Gas hydrate provinces are present in at least in two areas along Brazil’s continental margin: (1) the Rio Grande Cone in the southeast, and (2) the Amazon deep-sea fan in the equatorial region. The occurrence of gas hydrates in these depocentres was first detected geophysically and has recently been proven by seafloor sampling of gas vents, detected as water column acoustic anomalies rising from seafloor depressions (pockmarks) and/or mounds, many associated with seafloor faults. The gas vents include typical features of cold seep systems, including shallow sulphate reduction depths (<4 m), authigenic carbonate pavements and chemosynthetic ecosystems. In both areas, gas sampled in hydrate and in sediments is dominantly formed by biogenic methane. Calculation of the methane hydrate stability zone for water temperatures in the two areas shows that gas vents occur along its feather edge (water depths between 510-760 m in the Rio Grande Cone and 500-670 m in the Amazon deep-sea fan) but also in deeper waters within the stability zone. Gas venting along the feather edge of the stability zone could reflect gas hydrate dissociation and release to the oceans, as inferred on other continental margins, or upward fluid flow through the stability zone facilitated by tectonic structures recording the gravitational collapse of both depocentres. The potential quantity of venting gas on the Brazilian margin under different scenarios of natural or anthropogenic change require further investigation. The studied areas provide a natural laboratory where these critical processes can be analysed and quantified.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

We consider open non-twist Hamiltonian systems represented by an area-preserving two-dimensional map describing incompressible planar flows in the reference frame of a propagating wave, and possessing exits through which map orbits can escape. The corresponding escape basins have a fractal nature that can be revealed by the so-called basin entropy, a novel concept developed to quantify final-state uncertainty in dynamical systems. Since the map considered violates locally the twist condition, there is a shearless barrier that prevents global chaotic transport. In this paper we show that it is possible to determine the shearless barrier breakup by considering the variation of the escape basin entropy with a tunable parameter.

A Brewer Spent Grain (BSG), the most abundant by-product of the brewing process, is mainly used in animal feed and biogas production. The aim of the present work is BSG valorization by yeast fermentation to produce carotenoids. R. mucilaginosa CBS316 was cultured on BSG syrups, supplemented or not with YE and PEP (s-Fsa and Fsa). The biomass and carotenoid production were optimized in flasks and then scaled-up in bioreactor. In flask tests, the maximum biomass concentration was 5.3 and 6.2 g/L for Fsa and s-Fsa cultures, respectively. The maximum carotenoid production was 833 μg/L in Fsa and 1159 μg/L in s-FSA. Considering that the highest specific productivity value (P 7.16 μg/g*h) was obtained with Fsa syrup, this medium was selected for the process scale-up. In bioreactor tests, the maximum concentrations of biomass (4.29 g/L) and carotenoid (396 ug/L) was reached at 72 hours of fer-mentation, 24 h later than in flask. The total carotenoid produced was 524 and 150 ug in bioreactor and flask cultures, respectively. The carotenoids production by R. mucilaginosa was obtained both in Fsa and s-Fsa syrups. The results confirm the possibility to use the syrup as it is, Fsa, thus limiting the process costs.

Statins prevent cardiovascular diseases, yet their use is limited by the muscle disturbances they cause. Rarely, statin-induced myopathy is autoimmune, but more commonly it is due to direct muscle toxicity. Available evidence suggests that statin-induced creatine deficiency may be a major cause of this toxicity, and that creatine supplementation prevents it. Statins inhibit guanidinoacetate methyl transferase (GAMT), the last enzyme in the synthesis of creatine, thus they decrease its intracellular content. Such decreased content could cause mitochondrial impairment, since creatine is the final acceptor of the phosphate group of adenosine triphosphate (ATP) at the end of mitochondrial oxidative phosphorylation. Decreased cellular synthesis of adenosine triphosphate (ATP) would follow. Accordingly, ATP synthesis is decreased in statin-treated cells. In vitro, creatine supplementation prevents the opening of mitochondrial permeability transition pore caused by statins. Clinically, creatine administration prevents statin myopathy in statin-intolerant patients. Additional research is warranted to hopefully confirm these findings. However, creatine is widely used by athletes with no adverse events, and has demonstrated to be safe even in double-blind, placebo-controlled trials of elder individuals. Thus, it should be trialed, under medical supervision, in patients who cannot assume statin due to the occurrence of muscular symptoms.

In this paper, we have established Hermite-Hadamard inequalities for r-preinvex functions via fractional integrals.

This investigation aimed to explore the impact of acute and regular physical exercise on Brain-Derived Neurotrophic Factor (BDNF) levels in individuals with obesity. Using the Population, Intervention, Comparator, Outcome, and Study design (PICOS) approach, the inclusion criteria were defined as follows: i) population - individuals with overweight or obesity of any age or gender; ii) intervention - acute or chronic interventions involving aerobic or anaerobic methodologies; iii) comparator - for acute effect studies, pre- and post-evaluations served as comparators, while interventions included at least one experimental group or the inclusion of a control group; iv) outcome - BDNF variability concerning the applied methodology; v) study design - restricted to experimental studies exclusively. Conducted in August 2022, the searches were carried out on PubMed, Academic Search Complete, and Web of Science. The risk of bias was assessed using the Risk of Bias in Non-randomized Studies (RoBANS) tool. Out of 98 potentially relevant articles, 16 met the eligibility criteria, encompassing 23 trials. Substantial heterogeneity was observed for both acute (I2 = 80.4%) and long-term effects (I2 = 88.7%). Additionally, RoBANS analysis indicated a low risk of bias for the included studies. The study's findings revealed a significant increase in the concentration of circulating BDNF in individuals with obesity compared to the control group following acute exercise. However, such an effect was not evident in the context of long-term physical exercise, with a small effect size (ES = 0.49) recorded in the latter scenario. The observed significant increase in BDNF levels post-acute exercise suggests a potential acute response mechanism contributing to the intricate interplay between exercise and neurotrophic factors in this population. Nevertheless, the absence of a similar effect in the context of long-term physical exercise implies a potential adaptation or ceiling effect. These findings underscore the importance of considering both the duration and nature of exercise interventions when exploring the neurobiological responses associated with obesity and exercise. The study provides valuable insights for future research and clinical implications in understanding the nuanced relationship between exercise, neurotrophic factors, and obesity.

In this paper, we classify the function space of all real-valued functions on R denoted as F(R,R) into 28 distinct blocks. Each block contains elements that share common features in terms of the cardinality of their sets of continuity and differentiability. Alongside this classification, we introduce the concept of the Connection, which reveals a special relationship structure between four well-known real-valued functions in real analysis: the Cantor function, Dirichlet function, the Thomae function, and the Weierstrass function. Despite the significance of this field, several perspectives remain unexplored.

Coagulation is the most sensitive step in drinking water treatment. Underdosing may not yield the required water quality, whereas overdosing may result in higher costs and excess sludge. Traditionally, the coagulant dosage is set based on bath experiments performed manually. Therefore, this test does not allow real-time dosing control, and its accuracy is subject to operator experience. Alternatively, solutions based on machine-learning (ML) have been evaluated as a computer-aided alternative. Despite these advances, there is open debate on the most suitable ML method applied to the coagulation process, capable of the most highly accurate prediction. This study addresses this gap, where a comparative analysis between ML methods was performed. As a research hypothesis, a novel data-driven fuzzy inference system (FIS) should provide the best performance due to its ability to deal with uncertainties inherent to complex processes. Although ML methods have been widely investigated, only a few studies report hybrid neuro-fuzzy systems applied to coagulation. Thus, to the best of our knowledge, this is the first study thus far to address the accuracy of this novel data-driven FIS for such application. The novel FIS provided the smallest error (0.86), indicating a promising alternative tool for real-time and highly accurate coagulant dosing in drinking water treatment.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

The effective Supervisory Control and Data Acquisition (SCADA) system can improve the reliability, safety and economic benefits of microgrid operation. In this research, the lower central controller and upper WEB monitoring system are connected by the SCADA system which is as the hub of microgrid intelligent monitoring platform. This system contains a set of specific functions programmed by Java as a middleware which can provide control and communication between the central controller and the upper monitoring system. The system realizes the real-time data acquisition and storage, the control instructions parsing and transmitting, the microgrid security and stability, the load balancing and resource recovery of the microgrid. All that functions have been tested and verified in the actual operation.

A 52-day experiment was conducted to determine the crude protein (CP) requirements of juvenile matrinxã Brycon amazonicus, and to evaluate their resulting growth performance, hematological parameters and enzymatic activities. Sixty fish (29.03g ± 1.16g) were distributed in 12 tanks (310 L) with a completely randomized design, and maintained at four dietary crude protein levels (270, 320, 350, 390 g.kg-1) for 52 days. The results revealed that the fish fed diet 390 g.kg-1 CP had the best final weight, weight gain, feed conversion ratio, specific growth rate, protein efficiency ratio and lipid retention rate. The same could be stated for hematocrit, number of circulating erythrocytes, triglycerides and total proteins of the hematological profile (p&lt;0.05). In the whole body composition, dry matter content was lower in the fish fed 390 g.kg-1 CP, while lipid content was higher in the fish fed 350-390 g.kg-1 CP (p&lt;0.05). No differences were observed in CP and ash (p&gt;0.05), or in the activities of digestive enzymes (p&gt;0.05). In short, our findings suggest benefits of the 390 g.kg-1 CP feed for being the most adequate for this species’ juvenile stage.

Objective: To evaluate the direct costs of treating patients with neuromyelitis optica spectrum disorders (NMOSD) in outpatient care, from a hospital and Unified Health System (SUS) perspective. Methods: Observational study with data collection by microfunding, carried out with patients diagnosed with neuromyelitis optics, treated at a university hospital, in the city of Rio de Janeiro. Mann-Whitney tests were performed to measure cost differences between patient groups by disease severity and analysis perspective. Results: Nine individuals with a median age of 48 years (IQR 30 - 59 years) were included. The median total costs for patients with greater severity from the perspective of the SUS and the hospital were R$ 21,638.22 (IIQ: R$ 15,614.63; R$ 25,985.32) and R$ 32,094.11 (IIQ: R$ 25,610 .60; R$ 38,617.25) respectively. For patients with moderate severity the median was R$ 7,339.85 (IIQ: R$ 6,235.45; R$ 11,912.05) from the SUS perspective and R$ 11,505.80 (IIQ: R$ 7,339.85; R$ 22,424.76) from the perspective of the hospital, where the use of medications had a major impact. Conclusion: The main cost drivers were medicines, especially those used off-label, and procedures.

We developed two human induced pluripotent stem cell (hiPSC)/human embryonic stem cell-specific glycan-recognizing mouse antibodies, R-10G and R-17F, using the Tic (JCRB1331) hiPSC line as an antigen. R-10G recognizes a low-sulfate keratan sulfate, and R-17F recognizes lacto-N-fucopentaose-1. To evaluate the general characteristics of stem cell glycans, we used the hiPSC line 201B7 (HPS0063), a prototype iPSC line. Using an R-10G affinity column, an R-10G-binding protein was isolated. The protein yielded a single but very broad band from 480 to 1,236 kDa by blue native gel electrophoresis. After trypsin digestion, the protein was identified as podocalyxin by liquid chromatography/mass spectrometry. According to Western blotting, the protein reacted with R-10G and R-17F. The R-10G positive band was resistant to digestion with glycan-degrading enzymes, including peptide N-glycanase, but the intensity of the band was decreased significantly by digestion with keratanase, keratanase II, and endo-β-galactosidase, suggesting the R-10G epitope to be a keratan sulfate. These results suggest that keratan sulfate-type epitopes are shared by hiPSCs. However, the keratan sulfate from 201B7 cells contained a polylactosamine disaccharide unit (Galβ1-4GlcNAc) at a significant frequency, whereas that from Tic cells consisted mostly of keratan sulfate disaccharide units (Galβ1-4GlcNAc(6S)). In addition, the abundance of the R-10G epitope was significantly lower in 201B7 cells than in Tic cells.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

Multicellular life forms have evolved many times in our planet, suggesting that this is a common evolutionary innovation. Multiple advantages have been proposed for multicellularity (MC) to emerge. In this paper we address the problem of how the first precondition for multicellularity, namely "stay together" might have occurred under spatially limited resources exploited by a population of unicellular agents. Using a minimal model of evolved cell-cell adhesion among growing and dividing cells that exploit a localised resource with a given size, we show that a transition occurs at a critical resource size separating a phase of evolved multicellular aggregates from a phase where unicellularity (UC) is favoured. The two phases are separated by an intermediate domain where where both UC and MC can be selected by evolution. This model provides a minimal approach to the early stages that were required to transition from Darwinian individuality to cohesive groups of cells associated with a physical cooperative effect: when resources are present only in a localised portion of the habitat, MC is a desirable property as it helps cells to keep close to the available local nutrients.

Let G be a connected Lie group with Lie algebra g. This review is devoted to studying the fundamental dynamic properties of elements in the normalizer NG of G. Through an algebraic characterization of NG we analyze the different dynamics inside the normalizer. NG contains the well-known left-invariant vector fields and the linear and affine vector fields on G. In any case, we show the shape of the solutions of these ordinary differential equations on G. We give examples in low-dimensional Lie groups. It is worth saying that these dynamics generate the linear and bilinear control systems on Euclidean spaces and the invariant and linear control systems on Lie groups. Moreover, the Jouan Equivalence Theorem shows how to extend this theory to control systems on manifolds.

Solid state sensors having timing capabilities are becoming an absolute need in particle tracking techniques of future experiments at colliders. In this sense, silicon sensors having 3D structure are becoming an interesting solution, due to their intrinsic speed and radiation resistance. A characteristics of such devices is the strict dependence of their performance on their geometric structure, which can be widely optimised by design, thus requiring suitable tools for an accurate modeling of their behaviour. This paper illustrates the development, performance and use of the TCoDe simulator, specifically dedicated to the fast simulation of carrier transportation phenomena in solid state sensors. Some examples of its effectiveness in the design and analysis of 3D sensors is also given.

The links between rural and urban have often been the subject of study in Portugal. Nevertheless, the asymmetries between rural and urban have not ceased to increase over the last decades, contributing to an imbalance of economic, social, and territorial dimensions between regions. In order to counter this trend, policies to attract the population and tourism have been endorsed but have not been sufficient to promote territorial cohesion. This makes it necessary to rethink the capacity and the potential of rural territories in terms of mobilising their resources and, through them, promoting new and/or renewed relations with urban territories. This article aims to explore and map the links between urban and rural areas by analysing the routes taken by agri-food products, from production to marketing, with the support of a spatial analysis, using Geographic Information Systems (GIS). For that, we analysed a set of specialised and/or gourmet shops in Oorto and Lisbon, and their relations with the territories from which the commercialized agri-food products come. Most of these products originate in the inland rural regions of the country, and there is a clear geographical connection between the shops analysed and specific territories. Thus, it was possible to verify the increase in interest and consumption of agri-food products of rural origin and the spontaneous increase of this type of shop in the cities analysed, as well as identify the target audience of the shops and the spatial influence they have in the respective cities. These shops, in addition to selling agro-food products, are also promoters of rural territories in an urban environment.

Uncovering hidden mixture correlation among variables have been investigating in the literature using mixture R-vine copula models. These models are hierarchical in nature. They provides a huge flexibility for modelling multivariate data. As the dimensions increases, the number of the model parameters that need to be estimated is increased dramatically, which becomes along with huge computational times and efforts. This situation becomes even much more harder and complicated in the mixture Regular vine models. Incorporating truncation method with mixture Regular vine models will reduce the computation difficulty for the mixture based models. In this paper, tree-by-tree estimation mixture model is joined with the truncation method, in order to reduce the computational time and the number of the parameters that need to be estimated in the mixture vine copula models. A simulation study and a real data applications illustrated the performance of the method. In addition, the real data applications show the affect of the mixture components on the truncation level.

Plants are affected by soil environments to the same extent they affect soil functioning through interactions between environmental and genetic factors. Here, five plant species (broad bean, pea, cabbage, fennel, and olive) grown under controlled pot conditions were tested for their ability to differently stimulate the degradation of standard litter. Litter, soil C and N contents and soil microbial abundance were measured. The architecture and morphological traits of roots systems were also evaluated by using specific open-source software (SmartRoot). Soil chemical and microbiological characteristics were significantly influenced by the plant species. Variations in soil C/N dynamics were correlated with the diversity of root traits among species. Early-stage decomposition of the standard litter changed on the basis of the plant species. The results indicated that key soil processes are governed by interactions between plant roots, soil C and N, and the microbial metabolism that stimulate decomposition reactions. This, in turn, can have marked effects on soil chemical and microbiological fertility, both fundamental for sustaining crops, and can promote the development of new approaches for optimizing soil C and N cycling, managing nutrient transport, and sustaining and improving net primary production.

The oral administration of (R)-3-hydroxybutyl-(R)-3-hydroxybutyrate, allows inducing a beneficial level of blood ketone bodies without the adverse effects due to the adhesion to a ketogenic diet. Several studies documented the therapeutic effectiveness of the (R)-3-hydroxybutyl (R)-3-hydroxybutyrate in treating neurodegenerative diseases as well as its boosting activity of athletic and cognitive performances during prolonged physical exercises. Further studies considering this ketone body ester for therapy of other pathologies are also underway. In the present work, we describe the synthesis of (R)-3-hydroxybutyl-(R)-3-hydroxybutyrate through the enantioselective transesterification of racemic ethyl 3-hydroxybutyrate with (R)-1,3-butanediol catalyzed by immobilized Candida antarctica lipase B (CAL-B). The enantiopure (R)-1,3-butanediol was in turn obtained from the kinetic resolution of the racemate by CAL-B catalyzed acetylation with vinyl acetate. The economy of the synthetic procedure has been improved by recycling the unreacted (S) enantiomers of the ethyl 3-hydroxybutyrate and 1,3-buatnediol after stereochemical inversion achieved by tosylation and SN2 with ammonium acetate. The overall procedure allows to incorporate up to 70% of the starting racemic reagents into the final product.

The compatibility between the de Sitter Swampland conjecture and Ho\v{r}ava-Lifshitz $F(\bar{R})$ theories with a flat FLRW metric is studied. We first study the standard $f(R)$ theories and show that the only way in which the dS conjecture can be made independent of $R$ is by considering a power law of the form $f(R)\sim R^{\gamma}$. The conjecture and the consistency of the theory puts restrictions on $\gamma$ to be greater but close to $1$. For the $F(\bar{R})$ theories described by its two parameters $\lambda$ and $\mu$ we use the equations of motion to construct the function starting with an ansatz for the scale factor in the Jordan frame of the power law form. By doing a conformal transformation on the three metric to the Einstein frame we can obtain an action of gravity plus a scalar filed by relating the parameters of the theory. The non-projectable and projectable cases are studied and the differences are outlined. The $F(\bar{R})$ function obtained consists of terms of the form $\bar{R}^{\gamma}$ with the possibility of having negative power terms. The dS conjecture leads to inequalities for the $\lambda$ parameter, in both versions it gets restricted to be greater but close to $1/3$. For the general case in which $\mu$ and $\lambda$ are considered as independent, the action contains an extra term but we propose that the conjecture is still applicable. Once again the non-projectable and projectable cases are studied. The $F$ function obtained has the same form as before, the consistency of the theory and the dS conjecture lead to a set of inequalities on both parameters that are studied numerically. In all cases $\lambda$ is restricted by $\mu$ around $1/3$ and we obtain $\lambda\to1/3$ if $\mu\to0$. Finally we consider the $f(R)$ limit $\mu,\lambda\to1$ and we obtain consistent results.

In this work, we explore a the different forms of a new type of modified gravity, namely f(φ) gravity. We construct the Big Rip type for the energy density and the curvature of the universe. We show that dark energy is a result of the transformation of the field φ mass (dark matter) to energy. In addition, we provide that Ω_{m}≈0,050, Ω_{DM}≈0,2, Ω_{DE}≈0,746, is in excellent agreement with observation data. We explore a generalized formalism of braneworld modified gravity. We also construct a new field equations, which generalize the Einstein field equations. We provide a relation between the extra dimension in 3-brane with the vacuum energy density. We show that the energy density of matter depends directly on the number of dimensions. We manage to find the value of the Gauss-Bonnet coupling α=1/4 which is a good agreement with the results in the literature, this correspondence creates a passage between f(R) gravity and Gauss-Bonnet gravity, this comparison leads to a number of bulk dimensions equal to D=10¹²¹+4.

Gender Identity Dysphoria (GID) is a condition characterized by a strong and persistent identification with the opposite sex. These people consider themselves victims of a sort of biological accident: "a soul in a wrong body". There are numerous theories on the origin of transsexualism: genetic, hormonal and psychological causes have been hypothesized, but those currently most accredited are the neuroanatomical ones. The cornerstones of hormone conversion therapy (Gender Affirming Hormone Therapy, GAHT) are feminizing hormones for transgender women (MtFs) and virilizing for transgender males (FtMs). GID can be present among adolescents and older people. For adolescents is now accepted reversible treatment of puberty withdrawal with hormones that stops the progression of pubertal development in the biological direction not accepted; for elderly people is suggested GAHT in reduced doses. Physicians should consider and discuss with people with GID about fertility preservation, general and cancer risks. We present also data of 127 transsexual patients enrolled at the Garibaldi-Nesima Andrology Clinic in Catania (Italy) from 2003 to 2020. To optimize the conversion treatment with sex hormones, transsexuals require long-term follow-up. GAHT must be performed by a doctor who is familiar with these problems. Therefore, the “do-it-yourself” trend and the lack of medical and laboratory checks over time should be absolutely discouraged. Before proceeding with the surgical sex reassignment, it is recommended to refer to an endocrinologist and psychologist or psychiatrist for a period of 2-3 years. The transition surgical conclusion process must be practiced by a quality surgical team.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

Currently, there is no effective antiviral therapy recommended for the new coronavirus disease 2019 pneumonia (COVID-19). The purpose of this pilot study was to evaluate the safety of Ozonized Saline Solution (O₃SS) used as a complementary therapy in adult patients COVID-19. Twenty-five adult patients who were hospitalized with mild to severe COVID-19 symptoms, who met the inclusion criteria and were being treated from April 18^rd to April 26th, 2020, at the Viamed Virgen De La Paloma Hospital, Madrid, Spain were included in this study. Patients were allocated to receive standard care (SC) that included 200-400 mg hydroxychloroquine twice daily for 5-7 days plus Tocilizumab 400 mg twice daily for 5 days, low molecular weight heparin (LMWH) and 40 mg-60 mg metil-prednisone plus O₃SS, 200 mL, 3-5 µg/mL daily for 10 days. No control group was included, data were compared to clinical trials in this subject. Primary outcomes of treatment with O₃SS were an improvement of clinical symptoms and a reduction in mortality. Secondary end points evaluated included participant clinical status, laboratory examinations, and duration of viral shedding. None of the patients treated with SC + O₃SS died. Improvements in symptoms such as dyspnea, weakness, and reduction in body temperature were observed and corresponded with an improvement of laboratory finding including D-dimer, fibrinogen, LDH, and CRP. No side effects from the O₃SS treatment were observed. Conclusions: COVID-19 patients with mild to severe symptoms who received intravenous O₃SS as a complementary therapy demonstrated no side effects. This preliminary data will be served as base for a future study of the efficacy of this therapy.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

The effect of four soil-applied sulfur [S; 100 mg S kg-1 soil (100S) and 200 mg S kg-1 soil (200S)] in different sources (elemental S, ammonium sulfate, gypsum or magnesium sulfate) in protecting mustard (Brassica juncea L. Czern &amp; Coss.) from cadmium effects was studied. Based on the observed reduction in growth and photosynthesis in plants subjected to 100 and 200 mg Cd kg-1 soil, B. juncea cv. Giriraj was selected as the most Cd-tolerant among five cultivars (namely, Giriraj, RH-0749, Pusa Agrani, RH-406, and Pusa Tarak). Sulfur applied to soil mitigated the negative impact of Cd on sulfur assimilation, cell viability and photosynthetic functions, with a lower lipid peroxidation, electrolyte leakage, and contents of reactive oxygen species (ROS: hydrogen peroxide, H2O2, and superoxide anion, O2•−). Generally, added S caused a higher activity of antioxidant enzymes (ascorbate peroxidase, catalase and superoxide dismutase), and contents of ascorbate (AsA) and reduced glutathione (GSH), and increases in the activities of their regenerating enzymes (dehydroascorbate reductase and GSH reductase), as well as rises in S assimilation, biosynthesis of non-protein thiols (NPTs) and phytochelatins (PCs). Compared to the other S-sources tested, elemental S more prominently protected B. juncea cv. Giriraj against Cd-impacts by minimizing Cd-accumulation and its root-to-shoot translocation; decreasing cellular ROS and membrane damage, and improving Cd-chelation (NPTs and PCs), so strengthening the defense machinery against Cd. The results suggest the use of elemental S for favoring the growth and development of cultivated plants also in Cd-contaminated agricultural soils.

This paper proposes an upper bound for mine productivity and also a simple truck dispatch rule that demonstrates how tight the upper bound can be using simulation. It also proposes a greedy search to approximate the productivity upper bound, which is faster and often exact. Uncertainty is added to the simulation in order to verify how the productivity responds to it. Typically, the productivity upper bound is less tight close to its saturation point as a function of the number of trucks, where adding more trucks only increases queues. Furthermore, more uncertainty in the model typically leads to a less tight upper bound. The results are conducted using real data from an open pit mine in Brazil.

This research mapped significant social networks of victims of childhood sexual abuse, identifying relationships between childhood trauma and social bonds in adult life. Ten adult women, aged between 20 and 40 years, in psychiatric care for the consequences of trauma suffered in childhood participated in the research. For data collection, the map of significant social networks was used and analyzed through the structure, functions and attributes of the bonds. The network is composed of people from the Friendship, Family, Community, Work/Study and Health Teams group. The networks of friendships, family, co-workers or studies play a predominant role of emotional support, while the Health Teams also offer emotional support, but primarily provide clinical support in overcoming trauma and its consequences. The network of relationships has specific functions that maintain psychosocial integrity and help women to overcome the abuse suffered.

The increased availability of high resolution remote sensor data for precision agriculture 1 applications permits users to aquire deeper and more relevant knowledge about crops states that lead 2 inevitably to better decisions. The algorithm libraries being developed and evolved around these 3 applications rely on multi-spectral or hyper-spectral data acquired by using manned or unmanned 4 platforms. The current state of the art makes thorough use of vegetational indicies to guide the 5 operational management of agricultural land plots. One of the most challenging sub-problems is 6 to correctly identify and separate crop from soil. Thresholding techniques based on Normalized 7 Difference Vegetation Index (NDVI) or other such similar metrics have the advantage of being simple, 8 easy to read transformations of the data packed with useful information. Obvious difficulties arise 9 when crop/tree and soil have similar spectral responses as in case of grass filled areas in vineyards. 10 In this case grass and canopy are close in terms of NDVI values and thresholding techniques will 11 generally fail. Radiometric approaches could be integrated or replaced by a geometric approach that 12 is based on terrain data like Digital Surface Models (DSMs). These models are one of the ouputs 13 of orthorectification engines usually present in data acquired by using unmanned platforms. In 14 this paper we present two approaches based on DSM that are able to segment crop/tree from soil 15 while over gradient terrain. The DSM data are processed through a two dimensional data slicing or 16 reduction technique. Each slice is separately processed as a one dimensional time series to derive the 17 terrain and tree structures separately, here interpreted as object probability densities. In particular 18 the first approach is a Cartesian grid rasterization (CARSCAN) of the terrain and the second is its 19 immediate generalisation or radial grid rasterization of the DSM model (FANSCAN). The FANSCAN 20 recovers information from the original image at greater frequencies on the Fourier plane. These 21 approaches enable the identification of crop/tree from soil in case of slopes or hilly terrain without 22 any constraint on the displacement / direction of plant/tree row. The proposed algorithm uses pure 23 DSM information even if it is possible to fuse its output with other classifiers.

A wealth of Full Waveform (FW) LiDAR data are available to the public from different sources, which is poised to boost the extensive application of FW LiDAR data. However, we lack a handy and open source tool that can be used by potential users for processing and analyzing FW LiDAR data. To this end, we introduce waveformlidar, an R package dedicated to FW LiDAR processing, analysis and visualization as a solution to the constraint. Specifically, this package provides several commonly used waveform processing methods such as Gaussian, adaptive Gaussian and Weibull decompositions, and deconvolution approaches (Gold and Richard-Lucy (RL)) with users’ customized settings. In addition, we also developed functions to derive commonly used waveform metrics for characterizing vegetation structure. Moreover, a new way to directly visualize FW LiDAR data is developed through converting waveforms into points to form the Hyper Point cloud (HPC), which can be easily adopted and subsequently analyzed with existing discrete-return LiDAR processing tools such as LAStools and FUSION. Basic explorations of the HPC such as 3D voxelization of the HPC and conversion from original waveforms to composite waveforms are also available in this package. All of these functions are developed based on small-footprint FW LiDAR data, but they can be easily transplanted to the large footprint FW LiDAR data such as Geoscience Laser Altimeter System (GLAS) and Global Ecosystem Dynamics Investigation (GEDI) data analysis. It is anticipated that these functions will facilitate the widespread use of FW LiDAR and be beneficial for better estimating biomass and characterizing vegetation structure at various scales. The package and code examples can be found at https://github.com/tankwin08/waveformlidar.

Identification and segmentation of rock particles is very important in geology, mining, engineering construction, and environmental monitoring. Traditional methods for recognizing the rock particle characteristics are time-consuming, labor-intensive, and limited by the geographical scope of the sampling sites, which makes it more difficult to represent the spatial distribution of the rock particles accurately. Recent advancements in deep learning techniques offer promising solutions to automate this process. This study aims at utilizing state-of-the-art (SOTA) Mask R-CNN deep learning algorithm from the Detectron2 framework, to capture global features of rocks that will enable the recognition of rock particles more efficiently, just from having the rock images. These images are subject to image processing techniques such as a Gaussian filter, to denoise and smoothen the image, and an Illumination Adaptive Transformer (IAT) framework, to adjust the lighting exposure; all of which add to improve the quality of the image dataset. Afterward, the Mask R-CNN and Detectron2 models are utilized in training the images using transfer learning. Experimental results from evaluating the performance of the proposed algorithms showcase the effectiveness of the approach, thereby highlighting its potential to revolutionize rock particle segmentation across various domains.

(R)-(+)-3,5-Dinitro-N-(1-phenylethyl)benzothioamide 1 is a potential chiral solvating agent (CSA) for the spectral resolution of enantiomers by 1H NMR spectroscopy. The single enantiomer of 1 was synthesized from commercially (R)-(+)-a-methylbenzylamine 2 in two-steps with 85% yield.

We study certain function algebras and their operator algebra completions on r-discrete abelian groupoids, the corresponding conditional expectations, maximal abelian subalgebras (masa) and eigen-functionals.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Recently, we demonstrated the validity of anomalous numbers law, known as Newcomb-Benford´s law, at the mammalian neuromuscular transmission, considering different extracellular calcium concentrations . The present work continues to examine how alterations in extracellular solution modulate the first digit law in the context of the spontaneous release of acetylcholine from the neuromuscular junction. We investigated if the intervals of miniature potentials collected at the neuromuscular junction obey the law in a hyperkalemic environment. The analysis showed that the interval between the miniature potentials at high potassium concentrations follows Newcomb-Benford´s law. Also, our data allowed us to uncover a conformity fluctuation as a function of the number of intervals of the miniature potentials. Finally, we discuss the biophysical implications of the present findings.

In 2011, it was reviewed that there is a strong co-occurrence between major depression and chronic fatigue syndrome (CFS), with fatigue and physio-somatic symptoms being key symptoms of depression, and depressive symptoms appearing during the course of CFS. Moreover, the comorbidity between both conditions may in part be explained by activated immune-inflammatory pathways, including increased translocation of Gram-negative bacteria and increased levels of pro-inflammatory cytokines, such as interleukin (IL)-1. Nevertheless, the possible involvement of activated microglia in this comorbidity has remained unclear. This paper aims to review microglial disturbances in major depression, CFS and their comorbidity. A comprehensive literature search was conducted using the PubMed / MEDLINE database to identify studies that are relevant to this current review. Depressed patients present neuroinflammatory alterations, probably related to microglial activation, while animal models show that a microglial response to immune challenges including lipopolysaccharides is accompanied by depressive-like behaviors. Recent evidence from preclinical studies indicate that activated microglia have a key role in the onset of fatigue. In chronic inflammatory conditions, such as infections and senescence, microglia orchestrate an inflammatory microenvironment thereby causing fatigue. In conclusion, based on our review we may posit that shared immune-inflammatory pathways and activated microglia underpin comorbid depression and CFS and that activated microglia are the main orchestrators of this comorbidity. As such, microglial activation and neuro-inflammation may be promising targets to treat the overlapping manifestations of both depression and CFS.

Symmetry concepts in parametrized dynamical systems may reduce the number of external parameters by a suitable normalization prescription. If, under the action of a symmetry group G, parameter space A becomes a (locally) trivial principal bundle, A ~ A/G x G, then the normalized dynamics only depends on the quotient A/G. In this way, the dynamics of fractional variables in homogeneous epidemic SI(R)S models, with standard incidence, absence of R-susceptibility and compartment independent birth and death rates, turns out to be isomorphic to (a marginally extended version of) Hethcote's classic endemic model, first presented in 1973. The paper studies a 10-parameter master model with constant and I -linear vaccination rates, vertical transmission and a vaccination rate for susceptible newborns. As recently shown by the author, all demographic parameters are redundant. After adjusting time scale, the remaining 5-parameter model admits a 3-dimensional abelian scaling symmetry. By normalization we end up with Hethcote's extended 2-parameter model. Thus, in view of symmetry concepts, reproving theorems on endemic bifurcation and stability in such models becomes needless.

Previous studies demonstrate the critical importance of non-coding RNAs interfacing with chromatin-modifying machinery resulting in promoter-enhancer-based gene regulation and raise the possibility that many other enhancer-like RNAs may operate via similar mechanisms. Critically, more than 80% of the disease-linked variations identified in genome-wide studies are located in the non-coding regions of genomes, especially non-coding RNA, suggesting non-coding RNAs are relevant to disease. Thus, a critical path forward for understanding non-coding RNAs' role, especially long non-coding RNAs, is to understand the genomic regions' transcriptional regulation, especially non-coding regions. Here, we developed a user-friendly R package called SomaGene for studying and identifying enhancer-like non-coding RNAs with enriched somatic mutations in the cancer genome. SomaGene accepts different genomic variants (whole genome/exome somatic point mutations, structural variations, copy number variations) to identify those RNAs that significantly mutated in diseases (e.g., cancer). It then uses multiple publicly available genomics and epigenetics datasets including ENCODE epigenomics annotations, FANTOM5 tissue-specific expression profiles, disease-associated genome-wide association SNPs, and tissue-specific eQTL pairs to identify those RNAs with potentially enhancer function. SomaGene, as a powerful R package, can provide the opportunity to cancer scientists to study the roles of non-coding RNAs in different cancer genomes.

The authors previously found a model of universal quantum computation by making use of the coset structure of subgroups of a free group $G$ with relations. A valid subgroup $H$ of index $d$ in $G$ leads to a \lq magic' state $\left|\psi\right\rangle$ in $d$-dimensional Hilbert space that encodes a minimal informationally complete quantum measurement (or MIC), possibly carrying a finite \lq contextual' geometry. In the present work, we choose $G$ as the fundamental group $\pi_1(V)$ of an exotic $4$-manifold $V$, more precisely a \lq small exotic' (space-time) $R^4$ (that is homeomorphic and isometric, but not diffeomorphic to the Euclidean $\mathbb{R}^4$). Our selected example, due to to S. Akbulut and R.~E. Gompf, has two remarkable properties: (a) it shows the occurence of standard contextual geometries such as the Fano plane (at index $7$), Mermin's pentagram (at index $10$), the two-qubit commutation picture $GQ(2,2)$ (at index $15$) as well as the combinatorial Grassmannian Gr$(2,8)$ (at index $28$) , (b) it allows the interpretation of MICs measurements as arising from such exotic (space-time) $R^4$'s. Our new picture relating a topological quantum computing and exotic space-time is also intended to become an approach of \lq quantum gravity'.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

In this article, we give a brief review of the origin of the neutrino mass in some interesting non-linear supersymmetric models with R-symmetry. These models are able to address and solve the most important problems of the particle physics and provide mechanisms for neutrino mass generation and their mixing parameters in agreement with the current experimental data. Their prediction could be experimentally tested in the near future by collider experiments.

This paper presents a script that classify spatial patterns of residential urban growth using a morpho-structural approach. The script performs a combination of variography analysis and morphological closings over buildings possessing a residential function in 2002 and 2017 within a region located in southern France named Centre-Var. The different bounding regions then allow classifying new residential buildings into different categories according to their degrees of clustering/scattering and to their locations regarding existing urban areas. Preliminary results show that this protocol is able to provide useful insights regarding the degree of contribution of each new residential building to different patterns of urban growth (clustered infill, scattered infill, clustered edge-expansion, scattered edge-expansion, clustered leapfrog and scattered leapfrog). Open-access to the script and to the test region data is provided.

The study of energy sources has been an awareness of the modern world due to constraints on the current energy worldwide supply chain. The complexity of the theme as well as the consciousness of finite sources also the need of saving energy has become a priority. Although many papers have moved in this direction there is no record of papers studying the variables in a house heating system, which represents the highest energy consumption in many cold countries. This paper explores the energy-saving theme by studying the main variables present in houses’ heating systems in the winter season in cold countries like Canada, Russia, Norway, Iceland, Finland, etc. By using a novel combination of numerical thermal simulation by COMSOLTM and statistical analysis by MiniTabTM , it was possible to design an efficient thermal distribution in a house with the variables of the system by determining their significance and interaction qualitatively.

Nitrogen use efficiency (NUE) in maize (Zea mays L.) is an important trait to maximize yield with minimal input of nitrogen (N) fertilizer. Expired Plant Variety Protection (ex-PVP) Act-certified germplasm may be an important genetic resource for public breeding sectors. The objectives of this research were to evaluate the genetic variation of N-use traits and to characterize maize ex-PVP inbreds adapted to the U.S. Corn Belt for NUE performance. Eighty-nine ex-PVP inbreds [36 stiff stalk synthetic (SSS), and 53 non-stiff stalk synthetic (NSSS)] were genotyped using 26,769 single-nucleotide polymorphisms, then 263 single-cross maize hybrids derived from these inbreds were grown in eight environments from 2011 to 2015 at two N fertilizer rates (0 and 252 kg N ha⁻¹) and three replications. Genetic utilization and the yield response to N fertilizer were stable across environments and were highly correlated with yield under low and high N conditions, respectively. Cluster analysis identified inbreds with desirable NUE performance. However, only one inbred (PHK56) was ranked in the top 10% for yield under both N-stress and high N conditions. Broad-sense heritability across 12 different N-use traits ranged from 0.11 to 0.77, but was not associated with breeding value accuracy. Nitrogen-stress tolerance was negatively correlated with the yield increase from N fertilizer.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Acute lymphoblastic leukemia (ALL) is a blood cancer that primarily affects children but also adults. It is due to the malignant proliferation of lymphoid precursor cells that invade the bone marrow and can spread to extramedullary sites. ALL is divided into B cell (85%) and T cell lineages (10 to 15%); rare cases are associated with the natural killer (NK) cell lineage (<1%). To date, the survival rate in children with ALL is excellent while in adults continues to be poor. Despite the therapeutic progress, there are subsets of patients that still have high relapse rates after chemotherapy or hematopoietic stem cell transplantation (HSCT) and an unsatisfactory cure rate. Hence, the identification of more effective and safer therapy choices represents a primary issue. In this review, we will discuss novel therapeutic options including bispecific antibodies, antibody-drug conjugates,chimeric antigen receptor (CAR)-based therapies, and other promising treatments for both pediatric and adult patients.

Telemedicine is the use of Information and Communication Technology (ICT) for clinical health care from a distance. The exchange of radiographic images and electronic patient health information/records (ePHI/R) for diagnostic purposes has the risk of confidentiality, ownership identity, and authenticity. In this paper, a data hiding technique for ePHI/R is proposed. The color information in the cover image is used for key generation, and stego-images are produced with ideal case. As a result, the whole stego-system is perfectly secure. This method includes the features of watermarking and steganography techniques. The method is applied to radiographic images. For the radiographic images, this method resembles watermarking, which is an ePHI/R data system. Experiments show promising results for the application of this method to radiographic images in ePHI/R for both transmission and storage purpose.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

A facilitative transport system exists on the blood brain barrier (BBB) that has been tacitly assumed to be a path for glutamate entry to brain. But glutamate is a non-essential amino acid whose brain content is much greater than plasma, and studies in vivo show that glutamate does not enter brain in material quantities except in those small regions with fenestrated capillaries (circumventricular organs). The situation became understandable when luminal (blood facing) and abluminal (brain facing) membranes were isolated and studied separately. Facilitative transport of glutamate and glutamine exist only on the luminal membranes whereas Na+-dependent transport systems for glutamate, glutamine and some other amino acids are present only on the abluminal membrane. The Na+-dependent cotransporters of the abluminal membrane are in a position to actively transport amino acids from the extracellular fluid (ECF) into the endothelial cells of the BBB. These powerful secondary active transporters couple the energy of the Na+-gradient to move glutamate and glutamine into the ECF whereupon glutamate can exit to blood on the luminal facilitative glutamate transporter. Glutamine may also exit brain on a separate facilitative transport system that exists on the luminal membranes or glutamine can be hydrolyzed to glutamate within the BBB thereby releasing ammonia that is freely diffusible. The γ-glutamyl participate cycle participates indirectly by producing oxoproline (pyroglutamate) that stimulates almost all secondary active transporters yet discovered in the abluminal membranes of the BBB.

Bone tissue engineering has been developed in the past decades, with the engineering of bone substitutes on the vanguard of this regenerative approach. PCL based scaffolds are fairly applied for bone regeneration, and several composites have been incorporated, as to improve the devices’ mechanical properties and tissue ingrowth. In this study, HA was incorporated on PCL based scaffolds with two different proportions, 80:20 and 60:40. Devices were produced with two different techniques, SC and MB, and further investigated with regards to their mechanical characteristics and in vitro cytocompatibility. Results show the MB devices to present more promising mechanical properties, along with the incorporation of HA. The latter is also related to an increase in osteogenic activity and promotion. Overall, this study suggest PCL:HA scaffolds to be promising candidates for bone tissue engineering, particularly when produced by the MB method.

Selenium and iodine are essential micronutrients for humans. They are often deficient in food supply due to low phytoavailable concentrations in soil. Agronomic biofortification of food crops is one approach to overcome micronutrient malnutrition. This study focused on German consumers’ willingness to purchase selenium- and/or iodine-biofortified apples. For this purpose, an online survey was carried out. In this context, consumers were asked to choose their most preferred apple product from a set card of product alternatives (Discrete Choice Experiment). The multinomial logit model results demonstrated that German consumers’ have a preference in particular for iodine-biofortified apples. Furthermore, apple choice was mainly influenced by price, health claims, and plastic-free packaging material. Viewed individually, selenium did not exert an effect on product choice whereas positive interactions between both micronutrients exist.

Staphylococcus aureus mastitis remains a major challenge for dairy farming. Here, 24 mice were immunized and divided into four groups: G1: control; G2: Granulocyte Macrophage Colony-Stimulating Factor (GM-CSF) DNA vaccine; G3: F0F1 ATP synthase subunit α (SAS), succinyl-diaminopimelate (SDD), and cysteinyl-tRNA synthetase (CTS) recombinant proteins; and G4: SAS+SDD+CTS plus GM-CSF DNA vaccine. The lymphocyte subpopulations and the intracellular interleukin-17A (IL-17A) and interferon-γ production in the draining lymph node cells were immunophenotyped by flow cytometry. The immunophenotyping and lymphocyte proliferation was determined in spleen cells cultured with and without S. aureus stimulus. Immunization with S. aureus recombinant proteins generated memory cells in draining lymph nodes. Immunization with the three recombinant proteins plus GM-CSF DNA led to an increase in the percentage of IL-17A+ cells among overall CD44+ (memory), T CD4+, CD4+ T CD44+ CD27-, γδ TCR, γδ TCR+ CD44+ CD27+ and TCRVγ4+ cells. Vaccination with S. aureus recombinant proteins associated with GM-CSF DNA vaccine downregulates TH2 immunity. Immunization with the three recombinant proteins plus the GM-CSF DNA led to a proliferation of overall memory T, CD4+ and CD4+ TEM cells upon S. aureus stimulus. This approach fostered type 3 immunity, suggesting the development of a protective immune response against S. aureus.

A Friedmann-Lemaitre-Robertson-Walker space-time model with all curvatures k=0,±1 is explored in f(R,T) gravity. The solutions are obtained via the parametrization of the scale factor that leads to a model transiting from a decelerated universe to an accelerating one. The physical features of the model are discussed and analysed.

Single image deraining (SID) has shown its importance in many advanced computer vision tasks. Though many CNN based image deraining methods have been proposed, how to effectively remove raindrops while maintaining background structure remains a challenge that needs to be overcome. Most of the deraining work focuses on removing rain streaks, but in heavy rain images, the dense accumulation of rainwater or the rain curtain effect significantly interferes with the effective removal of rain streaks, and often introduces some artifacts that make the scene more blurry. In this paper, we propose a new network structure R-PReNet for single image deraining with good background structure maintaining. This framework fully utilizes the cyclic recursive structure of PReNet. Moreover, we introduce residual channel prior (RCP) and feature fusion modules for better deraining performance by focusing on background feature information. Compared with the previous methods, our method has significantly improvement effect on the rainstorm image with the artifacts removing and good visual detail restoring.

We analyze the behavior of relativistic spherical objects within the context of modified $f(R,T)$ gravity considering Tolman VI spacetime, where gravitational lagrangian is a function of Ricci scalar(R) and trace of energy momentum tensor(T) i.e,$ f(R,T)= R+ 2\beta T$, for some arbitrary constant $\beta$. For developing our model, we have chosen $\pounds_{m} = -p$, where $ \pounds_{m}$ represents matter lagrangian. For this investigation, we have chosen three compact stars namely PSR J1614-2230 [Mass=(1.97$\pm$ 0.4)M$_\odot$; Radius= 9.69$_{-0.02} ^{+0.02}$ Km] ,Vela X-1 [Mass=(1.77$\pm$ 0.08)M$_\odot$; Radius= 9.560$_{-0.08} ^{+0.08}$ Km] and 4U 1538-52 [Mass=(9.69)M$_\odot$; Radius= 1.97 Km]. In this theory the equation of pressure isotropy is identical to standard Einstein's theory. So all known metric potential solving Einstein's equations are also valid here. In this paper, we have investigated the effort of coupling parameter ($\beta$) on the local matter distribution. Sound of speed and adiabatic index are higher with grater values of $\beta$ while on contrary mass function and gravitational redshift are lower with higher values of $\beta$ . For supporting the theoretical results, graphical representation are also employed to analyze the physical viability of the compact stars.

3D printing is commonly used to create complex objects at a low cost. It has also been applied in the fabrication of metamaterials and metasurfaces, which alter the propagation path of electromagnetic waves. These structures have diverse applications, including enhancing beam direction, improving antenna gain and signal-to-noise ratio, and creating filters and reflectors. Metasurfaces are cheap to fabricate and their use is expected to boost antenna efficiency in 5G telecommunications and beyond. However, accurately characterizing their profile remains a significant challenge. This paper presents a low-cost fully automated 4-axis instrument for microwave metasurface charac-terization, overcoming limitations of manual methods and offering an efficient and accurate approach. This research represents a significant advancement in microwave metasurface characterization, enabling sophisticated techniques to advance wireless communication technolo-gies, as it is the case of the future 5G and millimeter-wave communication systems. The equipment has an approximate cost of $1550 USD and was able to characterize a metalens with a focal distance of 20 cm designed for signals at 30 GHz. It was possible to create 2D and 3D profiles of the intensity distribution focused by the metalens and extract parameters such as the gain (8.05 dB), 3dB depth of focus (11 cm) and full width at half maximum (2.17 cm). The comparison of the measurements with the diffraction calculations of the metalens showed a very good agreement between the in-tensity distributions and the parameters of the metalens.

The main contribution of this paper is to develop a graphical tool to evaluate the suitability of a candidate parametric model to fit a data set. The practical motivation is to check the adequacy of the so called SAINT model proposed in Jarner and Kryger (2011). This model has been implemented in practice by an important European pension fund concerned with setting annuity reserves for all current or former employees of Denmark. So, one particular relevant question is whether this mortality model is actually fitting old-age. Our graphical test can be described as follows. First we transform the data by means of the parametric model which is being evaluated. Should the model be correct, the transformed data will be in accordance with an Exponential distribution with rate 1. Then we construct a family of local linear hazard estimates based on the data on the transformed scale. Finally we use the statistical tool SiZer to assess the goodness-of-fit of the Exponential distribution to the data on the transformed scale. If the model is correct the SiZer map should not reveal any significant feature in the family of kernel estimates. Our method allow us to establish a diagnostic regarding the validity of the SAINT model when describing mortality patterns in four different countries.

Malassezia species are part of human commensal microbiota and is also related to diseases. Little is known about the interaction of these microorganisms with their host. Here we established two standard culture conditions for Malassezia spp. to perform infection assays using C. elegans and T. molitor. Invertebrate hosts infected by Malassezia spp. cultured in M9M resulted in higher death rate on survival assays when compared to yeasts cultured in standard Dixon medium indicating that M9M cultured Malassezia species have increased virulence. The culture and infection conditions established in this work, using invertebrate alternative models, are valuable tools to understand Malassezia-host interaction.

Pituitary adenylate cyclase-activating polypeptide receptor 1 (PAC1-R) has a higher affinity for pituitary adenylate cyclase- activating polypeptide (PACAP) than for vasoactive intestinal peptide (VIP). PACAP exerts its neuroprotective effects through PAC1-R. PAC1-R has become a target for drug development, and we targeted PAC1-R to screen small positive allosteric modulator 1 (SPAM1). SPAM1 has a neuroprotective effects, and in the D-galactose (D-gal) mouse model, SPAM1 improved the structure of the hippocampal dentate gyrus and restored the number of neurons. Compared with D-gal model mice, SPAM1 treatment upregulated the expression of Sirtuin 6 (SIRT6) and Lamin B1, and downregulated the expression of YinYang 1 (YY1) and p16. Consistent with this, the same results were obtained in senescent RGC-5 cells. Meanwhile, SPAM1 was also found to up-regulate SIRT6 and down-regulate YY1 expression in normal RGC-5 cells. Then, we further explored the mechanism of SPAM1 neuroprotection by whole transcriptome sequencing and proteomic analysis, and found that SPAM is involved in the longevity regulating pathway, and confirmed the up-regulation of neurofilament light polypeptide and neurofilament medium polypeptide by western blot, thus laying a pharmacological foundation for SPAM1 as a therapeutic agent for neurodegenerative diseases. polypeptide and neurofilament medium polypeptide. Thus, it lays a pharmacological foundation for SPAM1 as a therapeutic drug for neurodegenerative diseases.

Renewable energy sources are increasingly crucial for meeting global energy demands in an eco-friendly manner, particularly as the world shifts away from fossil fuels and faces higher volatility of the market prices. Portugal, a country with limited fossil fuel reserves and high energy dependency, has heavily invested in renewables in recent years. However, renewables like sunlight, wind, and water are inherently unsteady due to climate influences, resulting in energy production fluctuations. To mitigate this issue, energy storage systems are being deployed to stabilize renewable energy supply during production lulls. This project aims to assess an energy storage system and define technical specification in order to maximize profitability at the Finerge-owned Alto Douro wind farm. To achieve this, we've conducted an energy demand analysis, followed by simulations to assess system performance in relation to energy use and profit, while varying parameters such as power and efficiency. We've also compared commercial proposals from different battery manufacturers utilizing various technologies. Our findings suggest that high-power, quick charge-discharge lithium-ion batteries are the most suitable solution, given their efficiency and modularity. These attributes are vital for achieving current and future profitability.

In this paper, we first define the concepts of r-fuzzy soft α-open (semi-open and δ-open) sets on fuzzy soft topological spaces based on the article Aygunoglu et al. (Hacet. J. Math. Stat., 43 (2014), 193-208), and the relations of these sets with each other are established. In addition, we introduce the concepts of fuzzy soft δ-closure (δ-interior) operators, and study some properties of them. Also, the concept of r-fuzzy soft δ-connected sets is introduced and studied with help of fuzzy soft δ-closure operators. Thereafter, we define the concepts of fuzzy soft α-continuous (β-continuous, semi-continuous, pre-continuous and δ-continuous) functions, which are weaker forms of fuzzy soft continuity, and some properties of these functions along with their mutual relationships are discussed. Moreover, a decomposition of fuzzy soft α-continuity and a decomposition of fuzzy soft semi-continuity is obtained. Finally, as a weaker form of a fuzzy soft continuity, the concepts of fuzzy soft almost (weakly) continuous functions are defined, and some properties are specified. Additionally, we explore the notion of continuity in a very general setting called, fuzzy soft (L, M, N, O)-continuous functions and a historical justification is introduced.

Low-resource languages often face the problem of insufficient data, which leads to poor quality in machine translation. One approach to address this issue is data augmentation. Data augmentation involves creating new data by transforming existing data through methods such as flipping, cropping, rotating, and adding noise. Traditionally, pseudo-parallel corpora are generated by randomly replacing words in low-resource language machine translation. However, this method can introduce ambiguity as the same word may have different meanings in different contexts. This study proposes a new approach for low-resource language machine translation, which involves generating pseudo-parallel corpora by replacing phrases. The performance of this approach is compared with other data augmentation methods, and it is observed that combining it with other data augmentation methods further improves performance. To enhance the robustness of the model, R-Drop regularization is also used. R-Drop is an effective method for improving the quality of machine translation. The proposed method was tested on Chinese-Kazakh (Latin script) translation tasks, resulting in performance improvements of 4.99 and 7.7 for Chinese-to-Kazakh and Kazakh-to-Chinese translations, respectively.

Early detection of wildfires has been limited using the sun-synchronous orbit satellites due to their low temporal resolution and wildfires’ fast spread in the early stage. NOAA’s geostationary weather satellites GOES-R can acquire images every 15 minutes at 2km spatial resolution, and have been used for early fire detection. However, advanced processing algorithms are needed to provide timely and reliable detection of wildfires. In this research, a deep learning framework, based on Gated Recurrent Units (GRU), is proposed to detect wildfires at early stage using GOES-R dense time series data. GRU model maintains good performance on temporal modelling while keep a simple architecture, makes it suitable to efficiently process time-series data. 36 different wildfires in North and South America under the coverage of GOES-R satellites are selected to assess the effectiveness of the GRU method. The detection times based on GOES-R are compared with VIIRS active fire products at 375m resolution in NASA’s Fire Information for Resource Management System (FIRMS). The results show that GRU-based GOES-R detections of the wildfires are earlier than that of the VIIRS active fire products in most of the study areas. Also, results from proposed method offer more precise location on the active fire at early stage than GOES-R Active Fire Product in mid-latitude and low-latitude regions.

We present a methodology to enable users to interact with statistical information owned by an institution and stored in a cloud infrastructure. Mainly based on R, this approach was developed following the open-data philosophy. Also, since we use R, the implementation is mainly based on open-source software. R gives several advantages from the point of view of data management and acquisition, as it becomes a common framework that can be used to structure the processes involved in any statistical operation. This simplifies the access to the data and enable to use all the power of R in the cloud information. This methodology was applied successfully to develop a tool to manage the data of the Centre d’Estudis d’Opinió, but it can be applied to other institutions to enable open access to its data. The infrastructure also was deployed to a cloud infrastructure, to assure the scalability and a 24/7 access.

Multicriteria decision aid requires a database as a decision matrix, in which two or more alternatives are evaluated according to two or more variables selected as decision criteria. Several problems of this nature use measures by Likert scales. Depending on the method, parameters from these data (e.g. means, modes or medians) are required for calculations. This parameterization of data in ordinal scales has fueled controversy for decades between authors who favor mathematical/statistical rigor and argue against the procedure, stating that ordinal scales should not be parameterized, and scientists from other areas who have shown gains from the process that compensate for this relaxation. The aim of this article is to demonstrate the advantages of the Composition of Probabilistic Preferences (CPP) method in multicriteria problems with data from Likert scales. The CPP is capable of allaying the protests raised and obtaining more accurate results than descriptive statistics or parametric models can bring. The proposed algorithm in R-code involves the use of CPP with empirical distributions and fitting histograms of data measured by Likert scales. Two case studies with simulated datasets having peculiar characteristics and a real case illustrate the advantages of the CPP.

The Double Diaphragm Forming (DDF) process uses vacuum pressure and heat to pre-shape composite reinforcements between flexible diaphragms. Accurate modelling of heat transfer within DDF requires knowledge of the thermophysical properties of the constituent materials. This study investigates the specific heat and thermal conductivity of silicone diaphragms, carbon fibers (chopped and powdered), thermoplastic veils, and their combinations. Experiments measured the specific heat of each material using differential scanning calorimetry and the thermal conductivity of silicone and carbon fabric preforms using the transient plane source method and modified transient plane source method respectively. The influence of reheating cycles on specific heat of carbon fiber-veil samples and the effect of compaction on thermal conductivity of silicone and carbon fabrics were explored. While silicone exhibited linear specific heat behavior, the thermoplastic veil showed non-linearity due to phase change. The combined carbon fiber-veil samples demonstrated slight non-linear specific heat variations depending on reheating cycles. Thermal conductivity of the fabric preforms decreased with the addition of thermoplastic veil and under vacuum-compaction conditions. The established temperature-dependent property relationships provide valuable data for optimizing DDF preforming parameters and enhancing energy efficiency in composite manufacturing.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

The coffee leaf miner (CLM) Leucoptera coffeella moth is a major threat to coffee production. Insect damage is related to the feeding behavior of the larvae on the leaf. During the immature life stages, the insect feeds in the mesophyll, triggering necrosis and causing loss of photosynthetic capacity, defoliation, and significant yield loss to coffee crops. Chemical control is mandatory to sustain the coffee production chain, though market requirements move towards conscious consumption, claiming for more sustainable methods. In this overview, we discuss aspects about the CLM concerning biology, history, geographical distribution, economic impacts, and the most relevant control strategies in progress. Insights to develop an integrate approach for a safer and eco-friendly control of the CLM are discussed, including bio-extracts, nanotechnology, pheromones, and tolerant cultivars.

It has been proven that in standard Einstein gravity, exotic matter (i.e. matter violating the point-wise and averaged weak and null energy conditions) is required to stabilize traversable wormholes. Quantum field theory permits these violations due to the quantum coherent effects found in any quantum field . Even reasonable classical scalar fields violate the energy conditions. In the case of the Casimir effect and squeezed vacuum states, these violations have been experimentally proven. It is advantageous to investigate methods of minimizing the use of exotic matter. One such area of interest is extended theories of Einstein gravity. It has been claimed that in some extended theories, stable traversable wormholes solutions can be found without the use of exotic matter. There are many extended theories of gravity and in this review paper we first explore f(R) theories and then explore some wormhole solutions in f(R) theories including Lovelock gravity.

We analyse recent contradictory results and conclusions about the spectrum of the screened Coulomb potential $V(r)=-r^{-1}e^{-C/r}$. The well known Hellmann-Feynman theorem shows that all the bound states of the Coulomb potential ($C=0$) remain bounded as $C$ increases. We derive a simple approximate analytical expression for the eigenvalues for sufficiently small values of the screening parameter $C$ and an approximate asymptotic expression for the asymptotic behaviour of the s-state eigenvalues when $C\rightarrow \infty $. Present results are expected to resolve the discrepancy about the spectrum of the quantum-mechanical model just mentioned.

A locally-rotationally-symmetric Bianchi-I model filled with strange quark matter (SQM) is explored in f(R, T) gravity. We take f(R, T) = R + 2 f(T) = R + 2λT, where R is the Ricci scalar, T is the trace of energy-momentum tensor and λ is an arbitrary constant. Exact solutions are obtained by assuming that the expansion scalar is proportional to the shear scalar. This yields a constant value for the deceleration parameter, q = 2, which corresponds to the decelerated phase of the universe. The model is found to be physically viable for λ < −1. SQM during early evolution mimics ultra-relativistic radiation whereas at late times, it behaves as dust, quintessence or even the cosmological constant depending on the value of λ. The effective matter acts as a stiff fluid irrespective of the matter content and of the f(R, T) terms. The model is shear free at late times but remains anisotropic throughout the evolution. In the absence of the f(R, T) terms, SQM accelerates the universe. In the specific case when SQM vanishes at late times, the effect of f(R, T) is to accelerate the universe. The model admits the possibility that SQM could be an alternative to dark energy.

Polyhedral oligomeric silsesquioxane (POSS) is a suitable nanoscale reinforcement for thermosetting polymers, such as epoxy resin systems in order to modify its mechanical, thermal, and chemical properties. The inclusion of POSS in the epoxy resin at higher loading (greater than 1 wt.%), however, introduces the ductility during the fracture behavior of these nanocomposites. Consequently, the J-integral is used to quantify the fracture behavior of these materials and characterize the crack growth resistance curve against stable crack growth. A range of nanocomposites is prepared by adding 0.5, 1, 3, 5, and 8 wt.% of glycidyl POSS into DGEBF epoxy resin cured with an amine-based curing agent. From the fracture toughness experiment the load-displacement result confirms that when the POSS reinforcement is greater than 1 wt.%, the fracture behavior of the nanocomposite changes from brittle to ductile. For both brittle and ductile nanocomposites, the addition of POSS molecules improves the crack initiation toughness. The development of POSS–POSS compliant domains are reported previously, is attributed for this change in the failure behavior. The fractured images of POSS–epoxy nanocomposites, obtained using scanning electron microscopy, show that the increase in fracture resistance at higher values of POSS loading occurs due to the extensive shear yielding. Meanwhile, the increased fracture toughness at lower values of POSS loading occurs due to crack pinning and crack deflection.

We obtain exact solutions to the field equations for 5 dimensional LRS Bianchi type-I spacetime in $f(R,T)$ theory of gravity where specifically the following three cases are considered: (i) $f(R,T)=\mu(R+T)$, (ii) $f(R,T)=R \mu + R T \mu^2$ and (iii) $f(R,T)=R+\mu R^2+\mu T$ where $R$ and $T$ respectively the Ricci scalar and trace of the energy-momentum tensor. It is found that the equation of state (EOS) parameter $w$ is governed by the parameter $\mu$ involved in the $f(R,T)$ expressions. We fine-tune the parameter $\mu$ to obtain effect of phantom energy in the model, however we also restrict this parameter to obtain a stable model of the universe. It is noted that the model isotropizes at finite cosmic time.

In this paper, we introduce a new generalization of the r-Stirling numbers of the second kind based on the q-numbers via an exponential generating function. We investigate their some properties and derive several relations among q-Bernoulli numbers and polynomials, and newly de…ned (q, r, w)-Stirling numbers of the second kind. We also obtain q-Bernstein polynomials as a linear combination of (q, r, w)-Stirling numbers of the second kind and q-Bernoulli polynomials in w.

Background: We aimed to assess the association between DII and PD and the mediation effect of DII in the association of PD with systemic inflammation. Using the National Health and Nutrition Examination Survey (NHANES) 2009-2010, 2011-2012 and 2013-2014, participants that received periodontal exam and provided dietary recall data were included. The inflammatory potential of diet was calculated via DII. Periodontitis was defined according to the 2012 case definition. The clinical outcomes of interest were mean periodontal probing (PPD), mean clinical attachment loss (CAL) and thresholds of PPD and CAL. White blood cells (WBC), segmented neutrophils and C-reactive protein (CRP) were used as proxies for systemic inflammation. The periodontal measures were regressed across DII values using adjusted multivariate linear regression. Adjusted mediation analysis appraised the influence of DII in the association of periodontitis and systemic inflammation. 10,178 participants were included. DII was significantly correlated with mean PPD, mean CAL, thresholds of PPD and CAL, WBC, segmented neutrophils and DII (p&lt;0.01). A linear regression logistic adjusted for multiple confounding variables confirmed the association between DII and mean PPD (B = 0.02, Standard Error [SE]: 0.02, p&lt;0.001) and CAL (B = -0.02, SE: 0.01, p&lt;0.001). The association of mean PPD and mean CAL with both white blood cells and segmented neutrophils were mediated by DII (from 2.1 to 3.5%, p&lt;0.001). In the 2009-2010 subset, the association of mean CAL with serum CRP was mediated by DII (52.0%, p&lt;0.01). In conclusion, inflammatory diet and PD may be associated. Also, the inflammatory diet significantly mediated the association of leukocyte counts and systemic inflammation with periodontitis.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

Fowlpox virus (FPV) has been used as a vector for many years. To date, surprisingly, very little data exist on the persistence of fowlpox vaccines in chicken tissues, or what kind of immune cells respond to the vaccination at the site of inoculation. Although both humoral and cellular mediated immunity (CMI) play a part in overall immunity against FPV, little is known regarding the cell-mediated immune responses to FPV infection. The main aim of this paper was to measure persistence of the recombinant fowlpox vaccine in the skin tissues following vaccination. The results showed that the recombinant FPVs do not persist for long, and are cleared by 6 days post-vaccination (dpv). The response of immune cells (macrophages, B cells, CD4+ and CD8+ T cells) that infiltrating the site of vaccination was estimated.

Here, one hundred patients (50 smokers and 50 non-smokers) clinically diagnosed with COVID-19 were studied. Yet, bioinformatics was used to predict epitopes on Tobacco mosaic virus coat protein (TMV-CP) to produce antibodies towards SARS-CoV-2. Death was three times higher in non-smokers than in smokers. However, biochemical parameters did not separate the groups. Bioinformatics analysis predicted the presence of B-cell epitopes in TMV-CP, suggesting the production of antibodies anti-TMV-CP in smoker patients. Smokers may develop severe forms of COVID-19, but survival was superior in the evaluated group than in non-smokers. Anti-TMV-CP antibodies, potentially present in smokers, might act as a pro-immune agent against SARS-CoV-2 at earlier stages of infection. These data are helpful for future studies assessing COVID-19 in smokers.

Chamois are mountain ungulates (Subfamily Caprinae) which inhabit several medium and high altitude mountain ranges from southern Europe to the Near East. The first findings of Sarcocystis cysts in the musculature of chamois were reported in the 1970s. However, only limited work on the epidemiology of sarcocystosis and identification of the species of Sarcocystis in chamois has been done in the past. The present work was part of a comprehensive study on the parasites of chamois in Germany aiming to provide, for the first time, data on the prevalence and intensity of Sarcocystis infection in native Alpine chamois using histology examination of heart and/or diaphragm tissue samples collected from 216 chamois (40 kids and 176 chamois ranging of one up to 18 years of age). Sarcocysts were detected in either heart or diaphragm of 167/216 chamois (77.3%) with 131 of 183 heart samples and 127 of 215 diaphragm samples testing sarcocyst positive. Of the 181 chamois with both heart and diaphragm available (34 kids and animals up to 18 years of age), sarcocysts were detected in heart and/or diaphragm of 142 animals translating in an overall 78.5% prevalence of Sarcocystis infection (95%CI 72.5% - 84.4%). Sarcocysts were more frequently recorded in heart vs. diaphragm (72.4% vs. 56.4%; p=0.0021), and diaphragm positivity was associated with heart positivity (p=0.0001). Sarcocyst positivity (heart and/or diaphragm) was significantly (p<0.001) lower in kids than in the older chamois (27.1% vs. 88.6%, respectively) but prevalence did not differ between the sexes, regardless of the chamois’ age (p>0.3). Intensity of infection was generally low (<10 sarcocysts per cm² muscle cut) in both heart positive and diaphragm positive animals (94.7% and 93.7%, respectively) with heart yielding higher sarcocyst counts than diaphragm (p<0.001). Both heart and diaphragm sarcocyst counts were significantly (p<0.001) lower in kids than in the older chamois. Sarcocystis infection was demonstrated to be prevalent in chamois in Germany but intensity is apparently low. Further studies are desired to identify the species of Sarcocystis parasitizing the chamois using both phenotypic and molecular characteristics.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

This study clearly shows that the corona pandemic has a significant impact on consumers’ eating habits. More food is eaten overall, and more convenience products such as ready meals and canned food with a longer shelf life are purchased. The consumption of alcohol and confectionery has also increased. In return, the consumption of fresh fruit and vegetables has declined. It becomes clear that families who are financially affected by the pandemic represent a vulnerable group. With the increasing duration of the pandemic, repeated lockdowns, corona-related closings of schools and kindergartens, health consequences are to be expected in the medium to long term, especially for this population group.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

A national green planning strategy has recently been introduced in the Italian urban planning sector, aimed at making all local initiatives undertaken nationwide consistent with each other. At a regional level, Friuli Venezia-Giulia has recently implemented a Landscaping Plan, which is of an urban planning and ecological nature at an intermediate level between national and local. This article describes the local green plan of Latisana, which has been entitled Ecopolitana, given that it is represents the experimental phase, at a regional level, of the possibilities offered by landscape planning and design. Specifically, it outlines the multi-disciplinary approach used, demonstrating how landscape planning can be compared to the sustainable development of cities, with specific regard to the agricultural sector. Regarding the agricultural sector, a low-intensity cropping model is also suggested, based on the principles of agroecology and landscape ecology, which has already been implemented in the historical rural landscape of Plasencis (UD) and developed through GIS analysis and remote sensing processes. Its aim is to be the starting point for the achievement of the goals set in the 2030 Agenda, and especially Goals 13 (Climate action) and 15 (Life on land), given the current scarcity of agroecological infrastructures in the area of Latisana (UD) and the high percentage of soil used for intensive cropping.

The article explores Qualitative Comparative Analysis (QCA), an approach for establishing causal relationships between conditions and outcomes. QCA, applied in case studies and empirical analyses, facilitates generalizations for future research and addresses causal complexity by identifying various causal "recipes" leading to the same outcome. Three widely used QCA variants are Crisp-Set QCA (csQCA), Multi-value QCA (mvQCA), and Fuzzy-Set QCA (fsQCA), each with unique approaches. The article emphasizes the significance of bibliometric analysis in mapping a research field's intellectual structure, revealing key contributions and trends. In QCA, bibliometric analysis identifies leading researchers, affiliations, and influential countries. Results show QCA's widespread adoption across disciplines, with continuous growth in article production since 2013. The favored variant is fsQCA, followed by csQCA, and China notably contributes to QCA-related research. In conclusion, QCA proves a potent tool for discerning complex causal relationships in empirical studies, with its increasing interdisciplinary use indicating substantial potential for advancing scientific knowledge.

This paper introduces the spatial component in cross-section econometric estimations and specifically, the spatial dependence effect inherent in some of the variables involved in the modelling process. First, the spatial structure of the data from thematic maps is observed and Moran's spatial autocorrelation indicators are presented. Subsequently, the spatial weights matrix is built under different specifications. Finally, several modelling specification strategies are shown and the interpretation of the estimated coefficients. The theoretical concepts are illustrated with examples and their corresponding R software codes. This code and databases are available in a freely accessible repository in the BE2SHARE-EUDAT platform so that they can be easily reproduced.

This paper introduces an application of R programming language for geostatistical data processing with a case study of the Mariana Trench, Pacific Ocean. The formation of the Mariana Trench, the deepest among all hadal oceanic depth trenches, is caused by complex and diverse geomorphic factors affecting its development. Mariana Trench crosses four tectonic plates: Mariana, Caroline, Pacific and Philippine. The impact of the geographic location and geological factors on its geomorphology has been studied by methods of statistical analysis and data visualization using R libraries. The methodology includes following steps. Firstly, vector thematic data were processed in QGIS: tectonics, bathymetry, geomorphology and geology. Secondly, 25 cross-section profiles were drawn across the trench. The length of each profile is 1000-km. The attribute information has been derived from each profile and stored in a table containing coordinates, depths and thematic information. Finally, this table was processed by methods of the statistical analysis on R. The programming codes and graphical results are presented. The results include geospatial comparative analysis and estimated effects of the data distribution by tectonic plates: slope angle, igneous volcanic areas and depths. The innovativeness of this paper consists in a cross-disciplinary approach combining GIS, statistical analysis and R programming.

Radar altimetry provides valuable measurements to characterize the state and the evolution of the Antartica and Greenland ice sheet cover. Global Navigation Satellite System Reflectometry (GNSS-R) has the potential capacity of complementing the dedicated radar altimeters incrementing the temporal and spatial resolution of the surface height measurements. In this work we perform an study of the Greenland ice sheet using data obtained by the GNSS-R instrument aboard the British TechDemoSat-1 (TDS-1) satellite mission, designed primarily to provide sea state information, like sea surface roughness or wind, but not altimetric products. The data has been analyzed with altimetric methodologies, already proved in aircraft based experiments, to extract signal delay observables to be used to infer the topography of the Greenland cover. The penetration depth of the GNSS signals into ice has also considered. The topographic signal obtained is consistent with those obtained with other passive or active microwave sensors. The main conclusion derived from this work is that GNSS-R also provides valuable measurements of the ice sheet cover and, as taken at a variety of geometries and at least two frequency bands, they prospect different depths into the ice. They have thus potential to complement our understanding of the ice firn and its evolution.

Evidence on adult mammalian neurogenesis and scarce studies with human brains led to the idea that adult human neurogenesis occurs in the subgranular zone (SGZ) of the dentate gyrus and in the subventricular zone (SVZ). However, findings published from 2018 rekindled controversies on adult human SGZ neurogenesis. We systematically reviewed studies published during the first decade of characterization of adult human neurogenesis (1994–2004) – when the two-neurogenic-niche concept in humans was consolidated – and compared with further studies. The synthesis of both periods is that adult human neurogenesis occurs in an intensity ranging from practically zero to a level comparable to adult mammalian neurogenesis in general, which is the prevailing conclusion. Nonetheless, Bernier and colleagues showed in 2000 intriguing indications of adult human neurogenesis in a broad area including the limbic system. Likewise, we later showed evidence that limbic and hypothalamic structures surrounding the circumventricular organs form a continuous zone expressing neurogenesis markers encompassing the SGZ and SVZ. The conclusion is that publications from 2018 on adult human neurogenesis did not bring novel findings on location of neurogenic niches. Rather, we expect that the search of neurogenesis beyond the canonical adult mammalian neurogenic niches will confirm our indications that adult human neurogenesis is orchestrated in a broad brain area. We predict that this approach may, for example, clarify that human hippocampal neurogenesis occurs mostly in the CA1-subiculum zone and that the previously identified human rostral migratory stream arising from the SVZ is indeed the column of the fornix expressing neurogenesis markers.

In this paper, we explore a new norm on L^p-space called r-norm, and hence producing a new normed space called r-normed space. Measure theoretic and functional analytic properties are covered such as the relation between r-norm and the classical p-norm. An application of r-normed space in probability theory and statsitics is also presented, notably, its role as a rigorous framework in describing the coefficient of determination.

Motivation: UCSC Xena platform provides huge amounts of processed cancer omics data from big public projects like TCGA or individual reserach groups for enabling unprecedented research opportunities. In 2019, we developed UCSCXenaTools, an R package for retrieval of UCSC Xena data. However, an easier dataset exploration and analysis tool is still lack, especially for researchers without programming experience. Results: We develop UCSCXenaShiny, an R Shiny package to quickly explore, download all datasets from UCSC Xena data hubs. In addiction, a module based analysis framework is constructed to analyze and visualize data. Availability: https://github.com/openbiox/UCSCXenaShiny or https://cran.r-project.org/package=UCSCXenaShiny.

In this paper we have defined the effect of bulk viscosity on Quintessence model and scaler field potential as well as on classical field. We have shown the same effect for modified gravity with f(R,T)= R+f(T). In the derivation we have predicted the possibility of time dependent evolution of gravitational constant G and anisotropy.

This article investigates hydraulic percolation in saturated porous media, focusing on containment systems using sheet pile walls and gravity concrete dams. The Laplace equation, which governs hydraulic flow in porous media, is solved using the Finite Element Method through the ANSYS software. The modeling of the porous media employs a planar quadratic element called Plane 55, originally used for thermal problems, composed of four nodes and one hydraulic degree of freedom per node. The numerical results of the water pressure acting on the hydraulic structure, flow rate, and hydraulic gradient at the outlet of the porous media are compared with results obtained in the technical-scientific literature using flow nets. Two different methodologies are used to obtain the rate of seepage: by using the average hydraulic velocity or by calculating the integral of the hydraulic gradient perpendicular to the flow area. Both methodologies are compared and validated in the numerical simulations. This work also demonstrates the importance of mesh refinement for obtaining the flow rate in the studied hydraulic systems.

Background: Several kinds of research say that adjuvant blood glucose and blood pressure are usual, but an efficient solution for medical application count remains. This review analyzes the pandemic blood pressure and blood glucose to identify the publications which tell about the clinical practices and research gaps in systematic research.Methods: A study guides to identify the research of Blood Pressure (BP) and Blood Glucose. In order to analyze the recent innovations and research on BP and Blood glucose, the relevant publications and literature from journals were identified.Results: Co-morbidity of BP and Blood glucose is reported as very high. The commonness of blood pressure is thrice as high in type I diabetes patients and almost two times higher in type II diabetes patients when compared to others without Diabetes. The pervasiveness of getting depression is more in the female when compared with men. A detailed study about the linkage of BP and blood glucose tells that the relationship between them is not exactly clear.Limitations: Nearly all reviews providing the linkage of BP and blood glucose are with some limitations and they are not providing any clear conclusion.Conclusions: Present research tells that people having high blood glucose will have a greater chance of getting high blood pressure. More research is needed to state the linkage between BP, blood glucose, and the growth of diabetes mellitus issues and to provide support for managing Diabetes.

Micellar Casein Concentrate (MCC) is manufactured from microfiltration (MF) of skim milk utilizing ceramic or polymeric membrane filtration. While ceramic filtration has higher efficiency, use of polymeric is cost effective and the process is familiar to several US dairy processors. The aim of the present study was to develop an optimized membrane filtration process to produce MCC using spiral wound polymeric membrane filtration (SW MF) system by systematic selection of transmembrane pressure (TMP) and level of diafiltration (DF). Using skim milk as feed material, preliminary lab-scale MF experiments were conducted using 0.5 µm polyvinylidene fluoride (PVDF) membrane. Three TMP (34.5, 62.1, and 103.4 kPa) and three levels of DF (70, 100, and 150%) along with a process without DF as control were used in the study. Effect of TMP and effectiveness of DF on flux rates, SP removal, casein to total protein (CN/TKN) ratio, casein to true protein (CN/TP) ratio, rejection of casein (rej CN) and SP (rej SP) were evaluated. At all TMP values used in the study, the overall flux (O Flux) increased with the level of DF. Highest O Flux of 30.77 liter per meter square per hour (LMH) was obtained with 34.5 kPa pressure and 150% DF. The impact of DF was more pronounced at lower pressures than at the higher pressures used in the study. With controlled DF, instantaneous flux was maintained within 80% of initial flux for the entire process run. For all the experiments, casein has a rejection of 0.97 to 1.0, while serum protein has the lowest rejection of 0.10 at 34.5 kPa pressure and 150% DF level. Use of 34.5 kPa and DF level of 150 % contributed to 81.45% SP removal, and casein to true protein ratio of 0.96. SP removal data from the lab-scale experiments were fitted into a mathematical model using DF and square of TMP as factors. The model predicts SP removal within 90-95% of actual SP removal got from the pilot plant experiments.