This paper has experimentally measured volcanic tufa electrical conductance. The calculations are carried out in accordance with the potential of cyclic voltammetry in a constant state. The cyclic voltammograms nanoelectrode platinum prepared electrochemically were examined in the range -0.2 to 1.2 V vs. AgCl [Cl^-]:1.0 M in the presence and absence of volcanic tuff in the aqueous solution of 1.0 M HCl. The cyclic voltammetry studies show that the Nano platinum film suffers degradation when the potential exceeds +0.85 V, and below this potential, it is quite stable. The redox reaction of the electrode is reversible. The nanoparticle platinum synthesized at low temperature and high acid concentration exhibits higher electronic conductivities. It has been observed that, relative to area under the peak aggregate tests, the use of volcanic concrete was showing a large increase in electrical conductivity. It was shown that with cyclic voltammetry, three well-defined anode peak could be achieved at a power of 0.0, 0.4 and 0.6 V versus Ag/AgCl.

It is important to increase the quality of health and medicine. A wearable system for continuous monitoring of the patient is important to overcome this issue. Thus a patient with Arrhythmia due to its low cost and success in saving the life of the patient was the right option for the care partner. In addition, the device will provide a consumer with a smart smartphone application with accurate pulse beat and body temperature data in real time. MAX 30100 and LM35 are primarily used for the detection of human heart and temperature. The performance of these sensors is generated by an arrhythmia algorithm in the esp32 segment.

An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

Today, contamination from heavy metals in the atmosphere is a global concern. Efficient detection techniques are therefore necessary if heavy metal exposure levels in different media are to be determined. The voltammetry method for in situ detection of heavy metal ions is a very sensitive electrochemical method. This thesis explores emerging developments in electrode alteration, materials production and experimental optimization. An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

The outbreak of coronavirus 2 (SARS-CoV-2) has already taken on pandemic proportions and has affected more than 100 countries in recent weeks. It is imperative that global healthcare systems are prepared. Containment initiatives in Jordan, on the other hand, have decreased new cases by over 63%. The Jordanian national health system has been very pleased with its ability to adequately meet the needs of the patients diagnosed with SARS-CoV-2 pneumonia, and includes intensive care. From 2 March to 14 April 2020, between 4% and 8% of active infected patients in Jordan registered daily in intensive care. The percentage is very low.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

Bismuth oxides are well-known electro-catalysts in fuel cells systems; they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of BiO₂ and MnO₂ as catalysts in the pharmaceutical analysis is analytical method for the determination of heavy metal antibacterial agents in Pharmaceutical Dosage form is developed. The method is based on the voltammetric determination of heavy metal using Bidified platinum electrode by Bismuth oxide. The two components are oxidized at the Bidified electrode surface with the development of current that is linearly proportional to their concentrations in the range of 7.04*10^-7- 1*10^-3 M heavy metal. The oxidation reaction of the two components is pH-dependent, in which the buffer used is Britton-Robinson at pH = 7.00 where maximum peak current and maximum peak separation is obtained. The regression factors obtained from the calibration curves are 0.9812. The method of analysis was validated, where the limit of detection (LOD) and the limit of quantitation (LOQ) were calculated to be 1.44*10^-4 M, 4.36*10^-4 M and 1.27*10^-4 M, 3.84*10^-4 M respectively, the percentage recovery of both components was also calculated to 77 % for heavy metal.

Trends focused on the Global Innovation Index (GII) as a measure for progress of nanochemistry. This paper provides projections of recent developments in the word in nanochemistry based on the Global Innovation Index as a predictor for certain Arab countries. The GII is an annual ranking of countries by its ability and performance in innovation and is calculated on a basic average from five and two pillars in two sub-indexes, the Innovation Input Index and the Innovation Output Index. Each pillar represents a trait of creativity and consists of up to five measures, with a weighted average formula for measuring their ranking. In 2008, the GII rose to 36.3 in 2016 from 0.5. The GII is smaller than the GII in Arabic countries worldwide. During the years 2013-2016, the worldwide GII was increasing while for the same period, for Arabic countries, this decline could be explained by economic and industrial wars in the Arab region.

Ferrocene and its derivatives have ecologically effective antidetane properties. In this regard, ferrocene reacts with cyclic ketones and ferrosenylcarbinols are synthesized. It should be noted that ferrocene enters into electrophilic reactions and the process takes place in an acidic environment. In addition, the yield of the new product was small compared to the reactions of ferrocene with non-cyclic ketones. This is due to the spatial structures of molecules. The elemental analysis of obtained compounds was carried out; the structures were researched by cyclic voltammograms and Chronoamperometric.

As a consequence of a three-stage synthesis from terephthalic aldehyde, a series of 3,3 '- (1,4-phenylene) perchlorates including methyl, hydrogen, acetyl, bromio, methoxy and nitro groups (R = Br, H, Me). The matching formazans were reacted with formalin in dioxane in the presence of perchloric acid to produce tetrazin ium salts. Formazans were synthesized by reacting terephthalic aldehyde phenylhydrazone with ar ene diazonium tosylates in a DMF/pyridine combination. The use of ar ene diazonium tosylates greatly simplified the separation and purification of formazans. The p henylhydrazone was produced in aqueous dioxane using the usual approach from terephthalic aldehyde and phenylhydrazine/hydrochloric acid. Individual f ormazans and tetrazinium perchlorates were isolated and characterized by elemental analysis, IR, NMR, UV spectroscopy. The electrochemical reduction of tetrazinium perchlorates was investigated using cyclic voltammetry (CV). Thus, all salts in the cathode region have two one-electron reduction peaks, which are connected to the sequential production of a radical cation and a biradical. It was discovered that donor substituents (R: OMe, Me) in the aromatic ring at position 1 accelerate tetrazinium cation reduction, whereas acceptor substituents (R: NO₂, COMe,) inhibit this process. On this premise, it was proposed that in the presence of donor substituents in the aromatic ring at position 1, the matching bis-verdazyl radicals should be easily generated. As a result, 3,3'- (1,4-phenylene) perchlorates are possible antecedents of symmetric biradical systems based on verdazyl radicals.

This study on the production of a modern natural water electrochemical antimony (II) test include the use of platinum platinum electrode electrodes. Antimony (II) was pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = -680 mV. Compared to the platinum electrode, the platinum nanoelectrode exhibited superior performance and, unexpectedly, received a higher electrochemical response. After 25 min of accumulation, time the best-defined anodic peak was obtained with 0.2 mol L^-1 KNO₃ pH 5.0. Using these parameters, the L^-1 Sb ^{2 +} calibration plot was linear over range 1 = 10⁻⁸ to 5x10⁻⁶ mol. The precision was tested by carrying out eight replicate measurements at a concentration of 2.5x10⁻⁵ mol. L^-1; the variance coefficient was 2.9%. The method was applied to analyte determination in water samples from the river. Other metal ion attack on Sb's (II) voltammetric response has been studied. In the SEM image, the nanoparticle electrode was clearly observed and characterized by X-ray diffraction and cyclic voltammetry

Cold atmospheric plasma (CAP) has emerged as a promising therapeutic technology, distinguished by its safety, efficiency, and minimal side effects. With increasing applications in dermatology, CAP demonstrates antimicrobial efficacy against bacteria, viruses, and fungi, supports tissue proliferation and wound healing, and hinders the growth and migration of tumor cells. This review encompasses the concept, physical characteristics, and current research applications of CAP in dermatology. CAP, a gas cloud produced by ionizing gases, operates at room temperature, ensuring safety and efficacy in dermatological use. Its effects are mediated through active components like reactive oxygen and nitrogen species (RONS) and ultraviolet radiation. The extensive research covered in this paper explores CAP's applications in skin infections, immune-related diseases, and tumor diseases. As a biologically suitable technology, cold atmospheric pressure plasma finds widespread use in medicine, including medical device sterilization, dentistry, oncology, and dermatology. The direct and indirect forms of CAP applications, including plasma-activated liquids, complement each other. CAP holds promise as a dermatological treatment technique, but further exploration and research are needed. This article briefly explores CAP's diverse applications and potential utility within dermatology. The objective is to enhance the progress of plasma medicine by furnishing a concise overview of the applications of this groundbreaking technology in dermatological contexts.

Sensors became integrated through the control condition arrangement, either for visual, mechanical, biological, or chemical applications. New stuff is designed for detection, as Diluted Magnetic Semiconductors (DMS), and are considered attractive candidates that consist of a traditional 111- V, II-VI, or group IV semiconductor. Manganese Mn-doped GaN (Mn.Gac.N) epitaxial velum has a unique magnetic, visual and chemical properties in order to control system intelligent for detector design. The subject area of the magnetic properties of MnxGal-xN is on a large scale available, there are only a few studies on the visual properties and electrochemical properties of MnxGal-xN epitaxial velums. Where MnGaN velums were used in spintronic and opto-electronic applications according to their magnetic characterization and constructed MnGaN electrode are drop fabric potential for potentiometric sensor applications since they have good performance as ion-selective electrodes. The electrical and magnetic properties that allow the control of electron spin as well as complaint period, makes the materials ideal for spintronic applications. Designing such spintronic and optoelectronic devices based on MnxGal-xN requires a broader agreement of physical, visual, electrical and chemical properties epitaxial velums that are still seldom in the literature. This bailiwick displays the potential use of MnGaN semiconductor as an all solid-state potentiometric sensor for measuring anions in solutions in the control engineering field.

Background: This study was conducted to investigate medical students' lifestyle habits, including sleep quality, eating and drinking pattern, physical activity, and social status. Method: This research project is part two of a multi-institutional cross-sectional observational study conducted among medical students from six medical colleges in Saudi Arabia between September and December 2019. Results: 675 medical students were enrolled electively into the lifestyle study. About half of this number were male students, and the majority aged 18-24 years. Most students (87.6%) slept between 4-8 hours a day, and over 44% were dissatisfied with their sleep. Only 28.1% had three meals a day; about 40% of them usually or always skipped breakfast. While 44% usually or always eat fast food, 44.7% drink 2 liters of water per day. Moreover, male students were significantly consuming fast foods than females, p<0.001. The majority (63.3%) revealed they usually or always drink black coffee daily. Females were significantly more inclined to regular coffee consumption than males, p<0.001. Only 4.3% exercising for 30 minutes or more daily. The majority (65%) of the students were introverted; they had few close friends. Yet, 81% were somewhat satisfied or satisfied with their social life. Male students were predicted to be significantly more satisfied with their social life than females, p=0.001. Only 4.6% smoked cigarettes daily. Whereas 7.1% smoke e-cigarette daily. In contrast, only 0.3% use shisha (hookah) daily. Male medical students were substantially more predicted to be inclined to e-cigarette use than females (p <0.001. The top five leisure activities of a medical student are surfing social media (75.9%), watching movies (61.3%), hanging out with friends (58.1%), spent time with their family (55.4%), and browsing the internet (53.6%). Female medical students were significantly more inclined to surfing social media than male medical students, p=0.022; also, watching movies was preferred for females compared to males, p=0.006. Conclusion: This study revealed that the majority of medical students in Saudi Arabia exhibited healthy lifestyles to some extent, and these health-promoting behaviors differed based on gender, especially concerning physical activity and eating patterns. The findings of this study provide relevant information for future actions that will be geared towards effectively decreasing the occurrence of chronic illnesses and improving future doctor’s well-being.

Underwater wireless sensor networks (UWSN) have recently been proposed as a way to monitor and explore the water depths' environments. Efficiently delivering the data is still a challenging problem in these networks because of the weaknesses in the acoustic transmission. To tackle such a problem, we propose a novel algorithm provides controlling mechanisms for critical long-term data forwarding underwater sensor networks, called Hop by Hop Power-Efficient Routing Protocol (Hⁿ-PERP). The proposed Hⁿ-PERP is a centralized full-control model that enhances the network's throughput and energy efficiency by a set of solutions depend on power monitoring in UWSN nodes. In particular, the model provides a guaranteed mechanism for scheduling and processing data transmission based on number of nodes, hops between the nodes, energy level and congestion within each node to minimize energy levels or power consumption by avoiding disconnected probability for any node, which in turn maximizing the network lifetime. Simulation results show that our proposed model is consistent with energy level and congestion, and is more accurate for enabling routing and data transmission. Therefore, the data packet delivery ratio and overall throughput also achieves robust scenarios of very sparse or/and weak networks, to keep on Performance stability in UWSN via adjusting hop-by-hop delay and energy consumption during packages delivery.

The speech entailed in human voice comprises essentially para-linguistic information used in many voice-recognition applications. Gender voice-recognition is considered one of the pivotal parts to be detected from a given voice, a task that involves certain complications. In order to distinguish gender from a voice signal, a set of techniques have been employed to determine relevant features to be utilized for building a model from a training set. This model is useful for determining the gender (i.e, male or female) from a voice signal. The contributions are involved in two folds: (i) providing analysis information about well-known voice signal features using a prominent dataset, (ii) studying various machine learning models of different theoretical families to classify the voice gender, and (iii) using three prominent feature selection algorithms to find promisingly optimal features for improving classification models. Experimental results show the importance of sub-features over others, which are vital for enhancing the efficiency of classification models performance. Experimentation reveals that the best recall value is equal to 99.97%; 99.7% of two models of Deep Learning (DL) and Support Vector Machine (SVM) and with feature selection the best recall value is 100% for SVM techniques.

Learning dental procedures is a complex task involving the development of fine motor skills. The reported use of theories and/ or evidence for designing learning activities to develop the fine motor skills needed for dental practice is limited. The aim of this review is to explore the available body of knowledge related to learning fine motor skills in dentistry. Evidence from studies investigating motor skill learning highlights the negative impact of self-focus and self-regulation on learning outcomes, particularly during the early stages of learning. The development of activities and schedules that enable novices to demonstrate characteristics similar to experts, without the reported long period of ‘deliberate practice’, is clearly of value. Outcomes of learning implicitly are important in dentistry because working under stressful conditions is common, either during undergraduate study or in practice. It is suggested that learning implicitly in the simulation stage can reduce disrupted performance when transitioning to clinical settings. Therefore, further investigation of effective methods for learning dental fine motor skills is indicated, using approaches that result in robust performance, even under stressful conditions.

Extensive genomic analyses of Enterococcus cecorum isolates from sepsis outbreaks in broilers suggests a polyphyletic origin likely arising from core genome mutations rather than gene acquisition. This species is normal intestinal flora in avian species with particular isolates associated with osteomyelitis. More recently, the species has been associated with sepsis outbreaks affecting broilers during the first 3 weeks post hatch. Understanding the genetic and management basis of this new phenotype is critical for developing strategies to mitigate this emerging problem. Phylogenomic analyses of 227 genomes suggest that sepsis isolates are polyphyletic and closely related to both commensal and osteomyelitis isolate genomes. Pangenome analyses detect no gene acquisitions that distinguish all sepsis isolates. Core genome SNP analyses identify a number of mutations, affecting protein coding sequence, that are enriched in sepsis isolates. Analysis of the protein substitutions supports mutational origins of sepsis isolates.

Hand gesture recognition has many valuable applications in engineering and health care. This study proposes a novel model which can accurately distinguish hand gestures using forearm muscles' surface electromyogram (sEMG) signals. A deep learning algorithm with hyper parameters impacting the final model’s accuracy and a convolutional neural network (CNN) were employed in the recognition stage. The number of convolutional layers, kernels per layer, and neurons in the dense layer were selected for optimization, while the remaining parameters, such as the learning rate, batch size, and number of epochs, were chosen based on trial and error and prior knowledge. The optimal values for the selected hyperparameters were obtained using a genetic algorithm to achieve maximum recognition accuracy. The UC2018 Dual-Myo database was used for training and testing the model based on EMG signals characterizing the activity of eight different hand gestures. The final structure of the model consisted of two convolutional layers with 131 and 28 kernels, a dense layer with 111 neurons, and a softmax layer with eight neurons. Upon optimizing the hyperparameters using the genetic algorithm, the accuracy of the proposed model increased from 91.86% to 96.4% at best and 95.3% on average in real-time applications and 99.6% in an offline mode. Future work is warranted towards improving the architecture and the computational cost.

Background: The COVID-19 pandemic has changed the way dentistry has been practiced world over , this study sought to assess the impact of the COVID-19 pandemic on the patterns of attendance for dental treatment in a large hospital in Kuwait compare them to data from the year prior to the pandemic Methods: A total of 176,690 appointment records of 34,250 patients presenting to the AlJahra specialist hospital, Kuwait for dental treatment from April 2019 to March 2021 were analyzed. Types of procedures and the departments to which they presented were analyzed and the patterns of attendance before and during the pandemic were compared; Results: While there was a significant reduction in the number of orthodontic, endodontic and periodontal procedures there was no impact on oral surgery, restorative procedures or pediatric dentistry; Conclusions: There has been a return in the numbers of patients availing dental treatment, however, there has been a definite shift in the use of certain dental procedures .

This research aims to explore the complex interplay between supply chain resilience (SCR), digital supply chain (DSC), and sustainability, focusing on the moderating influence of supply chain dynamism. The goal is to understand how these elements interact within the framework of contemporary supply chain management and how they collectively contribute to enhancing sustainability outcomes. The sample size is 300 CEOs and managers. The study approach integrates quantitative research methods. Structural equation modeling (SEM) is utilized to quantitatively analyze the direct and indirect effects of SCR and DSC on sustainability. The numerous surveys we conduct among supply chain ecosystem stakeholders provide a rich picture of practical implications and contextual nuances. In sum, our early findings generally support a positive relationship between SCR and sustainability in and of itself decrying the need for more resilient supply networks for sustainability. We further find the beneficial impact of digital technologies in promoting sustainability via enhancing environmental control and controlling for efficiency in supply chains. We also offer evidence to show that supply chain dynamism compounds the positive logic between SCR and DSC and sustainability. As a final word, it must be noted that our work speaks to the burgeoning Supply Chain Dynamism as moderator literature by examining the direct and contingent effects of SCR and DSC on not only performance but sustainability. By shedding light on the moderating role of dynamism, the study provides fresh insights into the multifaceted nature of supply chain management and sustainability practices. The study's findings enhance theoretical understanding by elucidating the synergistic effects of SCR, DSC, and sustainability in dynamic supply chain settings. It augments existing theoretical frameworks by integrating concepts of resilience, digitalization, and sustainability into a comprehensive model. Practical and economical, the research offers actionable guidance for organizations aiming to improve sustainability performance through resilient and digitally advanced supply chains. By acknowledging the role of supply chain dynamism, managers can tailor strategies to manage disruptions effectively and leverage digital innovations. Economically, adopting sustainable practices can result in cost savings and competitive advantages. The research emphasizes the importance of aligning supply chain strategies with sustainability goals to drive long-term value and societal impact.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

This paper presents a novel DQ-based multicarrier Pulse Width Modulation PWM for a single-phase, three-level PV-powered grid-connected F-type inverter. The main control objective in the proposed inverter is to regulate the grid current with low total harmonic distortion and load power components compensation. Despite the F-type inverter’s advanced advantages, there are only a few works addressing the control issue in the literature yet. The proposed control and switching methods aim to achieve both DC side voltage balance and lowest switching losses. The proposed scheme has been designed based on a modified multi-carrier PWM switching algorithm. Consequently, the proposed control method able to satisfy the requirements of DC side voltage balance and achieve lower switching losses. A further advantage of the proposed control and switching methods is that they retain the main advantage of the F-Type inverter, which is that only 25% of the power switches are exposed to full DC voltage. This is an important advantage since it reduces the overall cost of the inverter and improves its reliability. Overall, the proposed modified multi-carrier PWM switching algorithm appears to be a promising approach for controlling the F-Type inverter, offering improved performance and efficiency compared to other control methods. The theoretical model was verified through simulation using MATLAB/Simulink. According to the simulation results, the grid current and dc capacitor voltages are successfully managed in all operational situations.

Single-molecule magnets (SMMs) have garnered significant interest in the field of molecular magnetism due to their unique magnetic properties at the nanoscale. These molecular systems exhibit magnetisation behaviour reminiscent of conventional bulk magnets but with distinct advantages such as size-dependent properties and potential applications in quantum computing and high-density data storage. However, challenges remain in harnessing their properties for practical applications, including their susceptibility to degradation and limited control over their assembly and organisation.

Due to its built-up chemoresistance after prolonged usage, the demand for replacing platinum in metal-based drugs (MBD) is rising. The first MBD approved by the FDA for cancer therapy was cisplatin in 1978. Even after nearly four and a half decades of trials, there has been no significant improvement in osteosarcoma (OS) therapy. In fact, many MBD have been developed, but the chemoresistance problem raised by platinum remains unresolved. This motivates us to elucidate the possibilities of the copper and zinc (CuZn) combination to replace platinum in MBD. Thus, the anti-chemoresistance properties of CuZn and their physiological functions for OS therapy are highlighted. Herein, we summarise their chelators, main organic solvents, and ligand functions in their structures that are involved in anti-chemoresistance properties. Through this review, it is rational to discuss their ligands’ roles as biosensors in drug delivery systems. Hereafter, an in-depth understanding of their redox and photoactive function relationships is provided. The disadvantage is that the other functions of biosensors cannot be elaborated on here. As a result, this review is being developed, which is expected to intensify OS drugs with higher cure rates. Nonetheless, this advancement intends to solve the major chemoresistance obstacle towards clinical efficacy.

Although Cable driven rehabilitation devices (CDRD) have advantages over traditional link-driven devices, including lightweight, ease of reconfiguration, remote actuation, etc, the majority of existing lower-limb CDRD is limited to rehabilitation in the sagittal plane. In this work, we extend our previous sagittal plane model (2DOF) to accommodate hip motion in the frontal plane (abduction/adduction) toward studying the feasibility of tracking bi-planar motion (combined frontal and sagittal plane motion) via intra-planar cable routing. Two optimization problems have been formulated to estimate an optimal location of the hip cuffs, first to estimate the optimal cuff location at each time step to identify a single ‘averaged’ optimal cuff location and second to calculate a single optimal cuff location for the entire gait cycle. The optimization solutions identified for the 3DOF model revealed that optimization of the location of cuffs on the anterior and posterior side of the hip joint for 4 cable configuration is not sufficient to generate the desired bi-planar motion. For simultaneous tracking of the bi-planar motion, 2 additional cables have been added at hip joints and are routed in an intra-planar manner. The simulation result with the 3DOF model confirmed successful bi-planar trajectory tracking. The various number of cables and cable routings for tracking bi-planar motion will be studied in future work.

Chronic obstructive pulmonary disease (COPD) is increasingly being recognized as a systemic disease rather than a mere disorder of the lungs. Central (respiratory) and peripheral (limb) muscle weakness are among the main pronounced systemic effects of COPD. While the disease primarily affects the lower limb muscles and contributes to gait impairment, COPD is also associated with an increasing risk of falls in patients (COPDp). Previous studies have reported higher rates of falls among COPDp (1.17 to 1.20 falls/person-year), amounting to four times higher than an age-matched healthy group. Potential fall risk factors include muscle weakness, impaired daily activities, cognitive dysfunction, and gait and balance impairment. Although COPDp often manifest many of these risk factors, there remains a gap in literature regarding falls during walking in this population. This study aimed to 1. analyze the literature to identify the risk factors of falling in COPDp, and 2. investigate the underlying mechanisms by which these risk factors can lead to increased prevalence of falling. The results suggest that in addition to the known risk factors of falling, low back pain and mental fatigue should also be considered as relevant risk factors in the treatment process of these patients. Moreover, respiratory problems, which are common in this population, have demonstrated pronounced effects on energy expenditure, gait, and other types of activities of daily living (ADLs), leading to reduced intensity, disrupted coordination of the trunk-pelvic structure with the lower limbs during gait, and altered motor control performance due to activation of muscles in an inefficient synergic manner. These problems potentially lead to the increased vulnerability of these patients to external disturbances and higher incidence risk of falls and injuries. Cognitive problems, which are typically due to reduced oxygen received by the brain, as well as general inflammation caused by COPD, also play a significant role in gait disruption and balance. Future research is warranted to determine the prevalence of falls in COPDp by examining the response of these patients to Medio-Lateral (ML) and Anterior-Posterior (AP) disturbances during gait in association with traditional and recommended fall risk factors.

The study titled "Molecular Choreography of DNA: Insights and Innovations" explores the intricate dance of DNA, shedding light on its structure, function, and regulation. This comprehensive review delves into the historical significance of DNA research, from Watson and Crick's double helix discovery to recent innovations in genomics and molecular biology. The review highlights DNA's roles in replication, repair, gene regulation, and chromatin dynamics, emphasizing the precision and complexity of its molecular choreography. Innovations like CRISPR-Cas9 gene editing and advanced sequencing technologies have revolutionized our understanding of DNA, opening new avenues for scientific exploration. This study aims to provide readers with a deeper appreciation of DNA's central role in life's choreographed processes.

There has been no significant efficacy in treatment for osteosarcoma (OS) metastasis after nearly four decades of trials. This motivates us to elucidate OS therapies according to their four bidirectional mutation stages. To refresh the OS therapy status quo, the historical developments and clinical advancements are briefly described. However, the main issue of metastasis remains unresolved, accounting for 90% of pulmonary metastasis deaths. Thus, this metastasis problem is related to immune evasion and chemoresistance that are being induced after long-term treatment by the use of immunotherapy for tumorigenesis. Therefore, it is rationale to discuss the relationship cycles of mutation stages including tumorigenesis, metastasis, immune evasion, and chemoresistance. Even though many combinational and targeted therapies have been developed to intensify these mutation treatments, successful clinical translations with higher cure rates are still rare. Through this review, an in-depth understanding of the bidirectional relationship between the four OS mutation stages and their respective therapies is provided. Herein, we summarise the medicines used to treat tumorigenesis, including COLGALT2 inhibitors, Tra2B, and AGAP1, miR-148a and miR-21-5p EVs, and the lncRNA LIFR-AS1. Following the medicines used to treat metastasis are AXL, miR-135a-5p, mRNA BCL6, TGFβ1, Tim-3, SOCS5, CASC15, KLF3-AS1, PDCD4, ATG5, and Rab22a-NeoF1. Then the medicines used to treat immune evasion are N-cadherin, anti-IL-9, USP12 inhibitor, IgG-4+ B-cells, LAP inhibitor, anti-Wnt2 mAb, anti-αvβ8 integrin, HK2-mediated IκBα, IDO inhibitor with NO, and TGF-βRII with anti-IgG1. Finally, the medicines used to treat chemoresistance are DHFR, FPGS, HSP-90AA1, XCT-790, ATKI, and IGF1. As a result, this contribution is expected to serve as a reference and guide for scientists and clinicians.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

This paper evaluates the global sustainable competitiveness of three blocks of power (US, China and EU) based on OGT (Organic Growth Theory) structure. In addition, a sensitivity analysis of COVID-19 on three measures of global sustainable competitiveness, economy, environment and social is also presented. OGT is a well-thought-through and standard framework for evaluation of any type of organiza-tion in their pathway to experience truly sustainable growth. GDP (Gross Domestic Product) is used as an economic measure; total carbon emissions equivalent is used as an environmental measure and HMI (Human Development Index) as a social measure. It is concluded that the pandemic has paused the evolution of countries to be truly world centric countries. However, the recovery plans seem to be highly aligned with the OGT scores and it is expected that the scores to improve dramatically.

Innovation and technology are important tools of minerals sector efficiency and productivity im-provement. The uptake of technologies has proven important levelrs to improve the productivity of mining sector. This paper provides a comprehensive analysis of mine-level productivity by using a global data of copper, gold, and platinum from 1991-2020. Various drivers of proioductivity have been analysed to draw policy insights. Empirical findings reveal significant disparities in technical efficiency and productivity across mines and regions. A further decomposition of TFP into its different components suggest that the adoption of innovative practices and investment in technology adoption could improve the overall productivity of these commodities. The findings also suggest that an appropriate input mix and optimal scale of production could boost platinum mining productivity. Regional disparities in productivity in different commodities (e.g., South Africa vs. Zimbabwe) give policymakers with insights into how to support production scale and productivity through appropriate input mixtures.

The research aims to improve some of the physical and hydro-physical properties of some Vertisols in the southern region (part of the eastern Houran Plateau) in Sweda Governorate at the south of Syria. Using different quantities of volcanic ash, soil samples were collected from the Al-Thahallah village from a depth of (0-30) cm, The experiment was designed according to the complete random design with one factor that represents the ash quantity (1.25, 2.5, 5) %, with three replicates for each treatment in addition to the control treatment a0. The experiment was carried out within the plastic pots during agricultural season 2018/2019, in which the wheat of the Sham variety 3 were cultivated as a cover plant. The results showed that the addition of volcanic ash at the quantity of 5% led to a significant increase in the infiltration rate by (328.60) %,%, where the filtration rate increased from 0.42 cm/hr -1 to 1.80 cm.h-1, as well as for each of the air porosity by (89) % and the volume of infiltrate water by (40) %, compared with the control. The above-mentioned addition also resulted in a decrease in both dry bulk density, total soil porosity and volumetric swelling coefficient by (18.60, 5.80, 314) % Respectively, compared to the control. The addition also contributed to the reduce in the weighted moisture content when saturation and the field capacity, at the level of significance of 5%. The research recommends adding volcanic ash to the soil at a quantity of 5%, and adding enhancements with volcanic ash at various levels such as organic waste.

Machine Learning (ML) has brought about a transformative era in reactor operations, reshaping monitoring, control, and optimization strategies. This survey comprehensively explores the diverse spectrum of ML applications in industrial reactors. From real-time sensor analysis ensuring reactor functionality to adaptive control algorithms ensuring stability, ML's impact is profound and multifaceted. The benefits of ML are equally evident in optimization, encompassing performance trend prediction, proactive maintenance, and fine-tuning of operations for enhanced efficiency. This review identifies dominant ML techniques, operations stages receptive to ML integration, core data sources, and critical input-output parameters. Aimed at both academics and practitioners, this exploration enriches reactor technologies, unlocking their full potential through insights driven by ML.

Nanofibres have gained increasing attention due to their advantages of having a high porous structure, narrow pore size and distribution, and a high specific surface area. One of the most efficient techniques for producing nanofibres is via electrospinning. Nanofibres are currently being used in various fields, including water filtration. Although nanofibres possess the ability to filter various components, the fibres generally have a low mechanical strength that can mitigate the performance over time. Therefore, in overcoming this issue, several studies have focused on improving the strength of the nanofibre membranes for a water filtration application. This review discusses the advantages and challenges of nanofibres for water filtration membranes and summarises the methods to increase the strength of the membranes, including solvent vapour, thermal treatment, and chemical crosslinking.

The epigenetic mechanism of DNA methylation is essential for regulating gene expression and adaptation in plants, especially when exposed to various environmental stressors such as drought, heat, and nutrient availability. The impact of these stressors can lead to alterations in DNA methylation patterns and gene expression, which this study aims to investigate. Specifically, we are interested in understanding how DNA methylation plays a role in controlling the expression of stress-response genes, as well as genes involved in plant growth and development. To accomplish this, we are analyzing the changes in DNA methylation patterns and gene expression in response to different stressors like drought and heat. Our research findings suggest that DNA methylation is a vital regulator of plant adaptation to environmental stress, and we hope to gain further insight into these mechanisms by identifying genes that exhibit differential expression in response to stress and analyzing their DNA methylation status. This study offers valuable insights into the development of crops that can thrive under changing climate conditions.

Current research in the field of antimicrobials is focused on the development of novel antibiotics and antimicrobial agents to counteract the huge dilemma that the human population is mainly facing in regards to the rise of bacterial resistance and biofilm infections. Host Defense peptides (HDPs) are a promising group of molecules for antimicrobial development as they share unique characteristics suitable for antimicrobial activity including their broad spectrum of activity and potency against bacteria. AamAP1 is a novel HDP that was identified through molecular cloning from the venom of the North African scorpion Androctonus amoeruxi. In vitro antimicrobial assays revealed that the peptide displays moderate activity against different strains of Gram-positive and Gram-negative bacteria. Additionally, the peptide proved to be highly hemolytic and displaying significantly high toxicity against mammalian cells. In our study, a novel synthetic peptide analogue named A3 was designed from the naturally occurring scorpion venom host defense peptide. The design strategy depended on modifying the amino acid sequence of the parent peptide in order to increase its net positive charge, percentage helicity and optimize other physico-chemical parameters involved theoretically in HDPs activity. Accordingly, A3 was evaluated for its in vitro antimicrobial and anti-biofilm activity individually and in combination with four different types of conventional antibiotics against clinical isolates of multi-drug resistant (MDR) Gram-positive bacteria. A3 was also evaluated for its cytotoxicity against mammalian cells. A3 displayed potent and selective in vitro antimicrobial activities against a wide range of MDR Gram-positive bacteria. Our results also showed that combining A3 with conventional antibiotics displayed a synergistic mode of action which resulted in decreasing the MIC value for A3 peptide as low as 0.125 µM. These effective concentrations were associated with negligible toxicities on mammalian cells. In conclusion, A3 exhibits enhanced activity and selectivity when compared with the parent natural scorpion venom peptide. The combination of A3 with conventional antibiotics may be pursued as a potential novel treatment strategy against MDR and biofilm forming bacteria.

Central nervous system (CNS) uses vision, vestibular, and somatosensory information to maintain body stability. Research has shown that there is more lumbar proprioception error among low back pain (LBP) individuals as compared to healthy people. In this study, two groups of 20 healthy people and 20 non-specific low back pain participants (LBP) took part in this investigation. This investigation focused on somatosensory sensors and in order to alter proprioception, a vibrator (frequency of 70Hz, amplitude of 0.5 mm) was placed on the soleus muscle area of each leg and two vibrators were placed bilaterally across the lower back muscles. Individuals, whose vision was occluded, were placed on two surfaces (foam and rigid) on force plate, and trunk angles were recorded simultaneously. Tests were performed in 8 separate trials; the independent variables were vibration (4 levels) and surface (2 levels) for within subjects and 2 groups (healthy and LBP) for between subjects (4×2×2). MANOVA and multi-factor ANOVA tests were done. Linear parameters for center of pressure (COP) (deviation of amplitude, deviation of velocity, phase plane portrait (PPP), and overall mean velocity) and nonlinear parameters for COP and trunk angle ((recurrence quantification analysis) RQA and Lyapunov exponents) were chosen as dependent variables. Results indicated that NSLBP individuals relied more on ankle proprioception for postural stability. Similarly, RQA parameters for the COP on both sides and for the trunk sagittal angle indicated more repeated patterns of movement among the LBP cohort. Analysis of short and long Lyapunov exponents showed that people with LBP caused no use of all joints in their bodies (non-flexible), are less stable than healthy subjects.

Middle East Respiratory Syndrome coronavirus (MERS-CoV) infects dromedary camels and zoonotically infects humans, causing a respiratory disease with severe pneumonia and death. With no approved antiviral or vaccine interventions for MERS, vaccines are being developed for camels to prevent virus transmission into humans. We have previously developed a chimpanzee adenoviral vector-based vaccine for MERS-CoV (ChAdOx1 MERS) and reported its strong humoral immunogenicity in dromedary camels. Here, we looked back at total RNA isolated from three immunised dromedaries pre and post-vaccination during the first day; and performed RNA sequencing and bioinformatic analysis in order to shed light on the molecular immune responses following a ChAdOx1 MERS vaccination. Our finding shows that a number of transcripts were differentially regulated as an effect of the vaccination, including genes that are involved in innate and adaptive immunity, such as type I and II interferon responses. The camel Bcl-3 and Bcl-6 transcripts were significantly upregulated, indicating a strong activation of Tfh cells, B cell, and NF-kB pathways. In conclusion, this study gives an overall view of the first changes in the immune transcriptome of dromedaries after vaccination; it supports the potency of ChAdOx1 MERS as a potential camel vaccine to block transmission and prevent new human cases and outbreaks.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

This study examines the moderating effect of trained human capital on the associations of accounting information systems, generalized auditing software, and technology adoption with the performance of external auditors among Saudi listed companies. This study used a survey-based methodology. The final sample consisted of 136 responses with an 8% response rate. Using Smart-PL4 analysis, the results showed that there is a positive correlation between accounting information systems and external auditors. Conversely, a negative relationship between generalized auditing software and external auditors has been documented. In addition, this study reported a negative association between technology adoption and external auditors. However, the results highlight the positive relationship between trained human capital and external auditors. Overall, this study provides valuable insights for accounting and auditing policymakers on how external auditors’ performance is influenced by several factors in the Saudi audit market.

Lifestyle physical activity (PA) and nutrition are known to be effective interventions in preventing and managing obesity related comorbidities is adult populations, but less so in children and adolescents. We examined the effectiveness of lifestyle interventions in children from minority ethnic populations in western high-income countries. Our systematic review included 53 studies involving 26045 children from minority ethnic populations within western countries, who followed lifestyle intervention programs lasting between 8 weeks and 5 years with an aim to prevent and/or manage childhood obesity and associated comorbidities, including adiposity and cardiometabolic risks. Studies were heterogenous in terms of lifestyle intervention components (nutrition, PA, behavioural counselling) and settings (community vs. schools and after schools). Our meta-analysis included 31 eligible studies and showed no significant effects of lifestyle interventions when they focused on body weight and body mass index (BMI) outcomes [pooled BMI mean change = -0.09 (95% CI -0.19, 0.01), p=0.09]. This was irrespective of the intervention program duration (< 6 months vs. ≥ 6 months), type (PA vs nutrition/combined intervention) and weight status (overweight or obese vs no normal weight), all showed no significant effects in the sensitivity analysis. Nonetheless, 19 of the 53 studies reported reduction in BMI, BMI z scores and body fat percentage. However, majority of lifestyle interventions adopting a quasi-design with a combined primary and secondary obesity measures (11 out of 15 studies), were effective in reducing obesity comorbidities of cardiometabolic risks including metabolic syndrome, insulin sensitivity, and blood pressure in children with overweight and obesity. Preventing childhood obesity and associated comorbidities in children from high-risk ethnic minority groups is best achieved using a combined PA and nutrition intervention approach, which jointly target preventing obesity and cardiometabolic disease primary and secondary outcomes, especially measures of diabetes, hypertension, and cardiovascular disease.

Nowadays, brain signal processing is performed rapidly in various brain-computer interface (BCI) applications. Most researchers focus on developing new methods for the future or improving the basic implemented models to identify the optimum standalone feature set. Our research focuses on four ideas. One of them introduces future communication models, and the others are for improving old models or methods. These are: 1) new communication imagery model instead of speech imager using the mental task: Due to speech imagery is very difficult, and it is impossible to imagine sound for all of the characters in all of the languages. Our research introduces a new mental task model for all languages that call Lip-sync imagery. This model can use for all characters in all languages. This paper implemented two lip-sync for two sounds, characters or letters. 2) New combination Signals: Selecting an inopportune frequency domain can lead to inefficient feature extraction. Therefore, domain selection is so important for processing. This combination of limited frequency ranges proposes a preliminary for creating Fragmentary Continuous frequency. For the first model, two s intervals of 4 Hz as filter banks were examined and tested. The primary purpose is to identify the combination of filter banks with 4Hz (scale of each filter bank) from the 4Hz to 40Hz frequency domain as new combination signals (8Hz) to obtain well and efficient features using increasing distinctive patterns and decreasing similar patterns of brain activities.3) new supplement bond graph classifier for SVM classifier: When SVM linear uses in very noisy, the performance is decreased. But we introduce a new bond graph linear classifier to supplement SVM linear in noisy data. 4) a deep formula recognition model: it converts the data of the first layer into a formula model (formula extraction model). The main goal is to reduce the noise in the subsequent layers for the coefficients of the formulas. The output of the last layer is the coefficients selected by different functions in different layers. Finally, the classifier extracts the root interval of the formulas, and the diagnosis does based on the root interval. For all of the ideas achieved the results of implementing methods. The results are between 55% to 98%. Less result is 55% for the deep detection formula, and the highest result is 98% for new combination signals.

The concerning rise in emergence and prevalence of resistant strains to drugs of M. tuberculosis has ,the prompted researchers to look for new and effective treatments. With this motive, biscoumarins were identified as the lead molecules on a whole-cell-based screening of several less explored low molecular weight bioactive compounds against M. tuberculosis strains. Among the screened biscoumarins, the highest dock score derivatives were synthesized (a-h) using a programmable microwave synthesizer for better yields and reaction control. The synthesized derivatives were evaluated against H37Rv, H37Ra, M. smegmatis, an MDR surrogate model, and other bacterial strains for the structure-activity response. Assessment of the synthesized library against mycobacterial strains led to the identification of compounds (f and d) as lead anti-tuberculosis agents. Compounds (f and d) exhibited less toxicity against human cell lines. At the same time, it displayed enjoyable activity wherein MIC concentrations were observed to be 16- and 32 µg/mL against the susceptible H37Rv, and H37Ra strains of M. tuberculosis and MIC value of 128 µg/mL for M. smegmatis, respectively. For mechanistic insights and identification of drug binding targets, molecular docking and dynamic simulations were employed for a panel of 16 mycobacterial enzymes essential for mycobacterial growth and survival. These in silico studies revealed the DprE1 enzyme as a druggable target for the anti-tuberculosis activity of the selected biscoumarins derivatives. Further investigation is underway in our laboratory, leading to its development as an anti-tuberculosis drug (animal model studies).

This paper addresses the conceptual exploration of various issues that form an integral part of the ethical dimensions surrounding the use of artificial intelligence (AI) in the field of marketing. We critically review some of the main ethical challenges AI poses to humanity: privacy, data security, bias, transparency, and accountability. Therefore, we will discuss the delicate balance between exploiting the transformation potential of AI for personally designed marketing strategies and ethical imperatives to safeguard the rights of consumers to retain trust. Then, the present regulatory landscape responding to these ethical challenges will be assessed by building on effective regulation, like the GDPR, existing proposed legislative frameworks, and industry guidelines. To underscore the role of an ongoing dialogue between marketers, technologists, ethicists, and regulators for developing a responsible AI ecosystem in marketing. Further, strategic recommendations for implementing company-based ethical AI marketing practices. The further strong guidelines provide enhancement transparency to consumers and investment in research to remove biases from algorithms. It also underscores principal scopes of further research and development, focusing on the need for new-age solutions to guide the ethical quagmires that AI-led marketing throws up. We suggest that integration should be done proactively and collaboratively. Thus, if attention is paid more to ethics and multidisciplinary dialogue, only such hyperbolic promises can be realized by AI-driven marketing. There are such promises through which AI-driven marketing will meet business goals and be huge at societies' values.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

Image registration (IR) is a process that deforms images to align them with respect to a reference space, making it easier for medical practitioners to examine various medical images in a standardized reference frame, such as having the same rotation and scale. This document introduces image registration using a simple numeric example. It provides a definition of image registration along with a space-oriented symbolic representation. This review covers various aspects of image transformations, including affine, deformable, invertible, and bidirectional transformations, as well as medical image registration algorithms such as Voxelmorph, Demons, SyN, Iterative Closest Point, and SynthMorph. It also explores atlas-based registration and multistage image registration techniques, including coarse-fine and pyramid approaches. Furthermore, this survey paper discusses medical image registration taxonomies, datasets, evaluation measures, such as correlation-based metrics, segmentation-based metrics, processing time, and model size. It also explores applications in image-guided surgery, motion tracking, and tumor diagnosis. Finally, the document addresses future research directions, including the further development of transformers.

Nowadays, speed up development and use of digital devices such as smartphones have put people at risk of internet crimes. The evidence of present crimes in a computer file can be easily unreachable by changing the prefix of a file or other algorithms. In more complex cases, either file divided into different parts or the parts of a file that has information about the file type are deleted, where the file fragment recognition issue is discussed. The known files are divided into different fragments, and different classification algorithms to solve the problems of file fragment recognition. A confusion matrix measures the accuracy of type recognition. In the present study, first, the file is divided into different fragments. Then, the file fragment features, which are obtained from Binary Frequency Distribution (BFD), are reduced by 2 feature reduction algorithms; Sequential Forward Selection algorithm (SFS) as well as Sequential Floating Forward Selection algorithm (SFFS) to delete sparse features that result in increased accuracy and speed. Finally, the reduced features are given to 3 classifier algorithms, Multilayer Perceptron (MLP), Support Vector Machines (SVM), and K-Nearest Neighbor (KNN) for classification and comparison of the results. In this paper, we proposed the algorithm of file type recognition that can recognize 6 types of useful files ( pdf, txt, jpg, doc, html, exe), which may distinguish a type of file fragments with higher accuracy than the similar works done.

Use of rhizosphere microorganisms provides an alternative or supplement to conventional plant breeding to improve water deficit tolerance of tomato plants. Experiment was carried out to explore the effect of two microbial species, AMF (Rhizophagus irregularis) and Bacillus subtilis, in single and co-application, on growth, colonization, and molecular aspects of tomato plants under drought stress. Co-inoculated plants showed less reduction in growth traits, photosynthetic pigments, colonization rate, and increased compatible solutes like proline which help in sustaining relative water content than non-inoculated plants. Inoculation considerably enhanced proline dehydrogenase activity, and significantly reduced both Δ1-pyrroline-5-carboxylate reductase Δ1-pyrroline-5-carboxylate synthetase activity causing lower proline accumulation in inoculated plants under drought stress. Co-inoculated plants showed obvious upregulation of antioxidant system, thus facilitating amelioration of oxidative stress through exclusion of reactive oxygen species. No inoculation under drought stress upregulated abscisic acid related genes expression but have no effect in plants inoculated either sole or mixed inoculation. Expression of aquaporin genes was upregulated in plants co-inoculated and with AMF alone under normal condition. However the expression of aquaporin genes were decreased or unaffected in plants inoculated with Bacillus subtilis but increased in non-inoculated plants. Co-applied AMF and bacillus subtilis substantially increase drought tolerance by upregulating proline metabolism, antioxidant enzymes and aquaporin genes. Therefore our results suggest that co-inoculation mediated drought tolerance is linked with increased proline accumulation, enhanced antioxidant enzyme activities and differential regulation of ABA biosynthetic and aquaporin genes, which is vital for osmotic adjustment of host plant.

The modulation of Nrf2 activity has been reported to be implicated in the pathology of various neurological disorders, including epilepsy. Previous studies have demonstrated that Nrf2 is activated in the post-status epilepticus rat model, however, the spatio-temporal, as well as cell type-specific expression of Nrf2 following brief epileptic seizures remains unclear. Here, we evaluated how an acute epileptic seizure affected the expression of Nrf2 and its downstream genes in the cortex and the hippocampus up to 1-week following the induced seizure. We found that after a pentylenetetrazol-induced seizure, Nrf2 significantly increased at 24 h at the mRNA level and 3 to 6 h at the protein level in the cortex. In the hippocampus, the Nrf2 mRNA level peaked at 3 h after the seizure, and no significant changes were observed in the protein level. Interestingly, the mRNA level of Nrf2 downstream genes peaked at 3-6 h after seizure in both the cortex and the hippocampus. A significant increase in the expression of Nrf2 was observed in the neuronal population of CA1 and CA3 regions of the hippocampus, as well as in the cortex. Moreover, we observed no change in the co-localization of Nrf2 with astrocytes neither in the cortex nor in CA1 and CA3. Our results revealed that following a brief acute epileptic seizure, the expression of Nrf2 and its downstream genes is transiently increased and peaked at early timepoints after seizure predominantly in the hippocampus, and this expression is restricted to the neuronal population.

The Saudi government has undertaken rapid and swift actions, such as suspending Omrah and holding international flights. Such affirmative actions enhanced citizens and residents’ confidence in the government officials’ ability to fight the pandemic. However, there are more than 361,178 reported cases of Covid-19 with 6131 deaths as of December 22, 202. As nurses are the largest component of the health care workforce in Saudi Arabia, it is important that they are trained and have the skills and resources to adapt, whether on the frontline of a crisis or in a clinical environment. Nurses play a key function in fulfilling the needs of medical treatment by being the most important part of the health care delivery system.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

The four solvent extractives obtained from aerial parts of Leucophyllum frutescens were evaluated for their Total Antioxidant Activity (TAA) by ammonium molybdate method, scavenging potential by 2,2-diphenyl-1-picrylhydrazyl (DPPH) and Trolox-Equivalent Antioxidant Capacity (TEAC) assays, metal-reducing potential by Cupric Reducing Antioxidant Capacity (CUPRAC) and Ferric Reducing Antioxidant Power (FRAP) assays, Total Phenolic Content (TPC), Total Flavonoid Content (TFC) and their biological activities. The study concluded that BULE exhibited total antioxidant activity (226.235±1.222 mg AA.Eq.gm-1 DE±S.D) by molybdate method, CHLE exhibited more scavenging potential (DPPH 209.589±8.500 mg trolox Eq.gm-1 DE±S.D and TEAC 210.166±7.954 mg trolox Eq.gm-1 DE±S.D) and reducing potential (CUPRAC 646.889±16.889 mg trolox Eq.gm-1 DE±S.D & FRAP 472.981±15.625 mg trolox Eq.gm-1 DE±S.D). Phytochemical quantification concluded high TPC by BULE (189.369±1.393 mg GA.Eq.gm-1 DE±S.D) and high TFC by CHLE (232.458±1.589 mg Qu.Eq.gm-1 DE±S.D). Strong inhibition of α-glucosidase and urease enzymes was observed by HELE (IC50 0.3321±0.007 mg.ml-1±SD) and BULE (IC50 4.09±0.357 mg.ml-1±SD) extractives, respectively. The hemolytic effect shown by hexane extract (HELE) was higher with HA50 25.545±0.927 ug.ml-1±SD whereas methanol (MELE), chloroform (CHLE), and butanol (BULE) exhibited hemolytic effects at higher concentration with HA50 400.067±1.364, 321.394±1.332, and 332.957±0.465 µg.ml-1±SD, respectively. GC-MS profiling of HELE of L. frutescens was performed for qualitative analysis. The principal phytochemicals tentatively identified by GC-MS analysis of HELE accounts for fatty acids (60.221%), lignans (17.687%), ketones (3.358%), phenols (2.584%), sesquiterpenes (1.265%), and aldehydes (0.345%).

The Kashmir valley is prone to flooding due to its peculiar geomorphic setup compounded by the rapid anthropogenic land system changes and climate change. The study assesses the impact of land use and land cover (LULC) changes between 1980 and 2020 and extreme rainfall on peak discharge and sediment yield in the Upper Jhelum Basin (UJB), Kashmir Himalaya, India using KINEROS2 model. Analysis of LULC change revealed a notable shift from natural LULC to more intensive human-modified LULC, including a decrease in vegetative cover, deforestation, urbanization, and improper farming practices. The findings revealed a strong influence of the LULC changes on peak discharge, and sediment yield relative to the 2014 timeframe, which coincided with the catastrophic September 2014 flood event. The model predicted a peak discharge of 115101 cubic feet per second (cfs) and a sediment yield of 56.59 tons/ha during the September 2014 flooding, which is very close to the observed peak discharge of 115218 cfs indicating that the model is reliable for discharge prediction. The model predicted a peak discharge of 98965 cfs and a sediment yield of 49.11 tons/ha in 1980, which increased to 118366 cfs and, 58.92 tons/ha respectively in 2020, showing an increase in basin’s flood risk over time. In the future, it is anticipated that the ongoing LULC changes will make flood vulnerability worse, which could lead to another major flooding in the event of an extreme rainfall as predicted under climate change and, in turn compromise achievement of sustainable development goals (SDG). Therefore, regulating LULC in order to modulate various hydrological and land surface processes would ensure stability of runoff and reduction in sediment yield in the UJB, which is critical for achieving many SDGs.

The objective of this study is to examine different types of bias present in assessment tools and techniques, identify and eliminate any forms of favoritism, and suggest effective approaches for advancing equity and objectivity in assessment procedures. The research utilizes a qualitative methodology, incorporating surveys and focus group discussions with educators and students to collect data. Thematic analysis is a method employed for the purpose of analyzing qualitative data. The results suggest that students hailing from diverse cultural backgrounds perceive partiality in the language and cultural context of evaluations, leading to diminished scores. According to academic professionals, standardized tests are subject to bias, and offering accommodations that cater to linguistic and cultural diversity may improve the academic achievement of students from diverse cultural backgrounds. The findings of this research are of great importance to professionals in the domains of education, policy development, and academia who seek to improve assessment practices and promote equitable educational opportunities for all learners.

We report the synthesis and characterization of Poly Methyl-Meth-Acrylate (PMMA)/Poly vinylalcohol (PVA) polymeric blend doped with different concentrations of Copper oxide (CuO) nanoparticles (NPs). The (PMMA-PVA)/CuO nanocomposite hybrid thin films (wt. % = 0%, 2%, 4%, 8%, and 16%) of CuO NPs are deposited on glass substrates via dip-coating technique. The transmittance (T%), reflectance (R%), the absorption coefficient (α), the optical constants [refractive index (n), extinction coefficient (k)], optical dielectric functions [ɛ',ɛ''] are investigated and interpreted. Tauc, Urbach, Spitzer-Fan, and Drude models are employed to calculate the optical bandgap energy (Eg) and the optoelectronic parameters of the nanocomposite thin films. The refractive index and optical bandgap energy of of (PMMA-PVA) polymeric thin film are found to be (1.5 to 1.85) and 4.101 eV, respectively. Incorporation of specific concentrations of CuO-NPs in (PMMA-PVA) polymeric thin films leads to a noticeable decrease in the optical bandgap energy and to an increase of the refractive index. Moreover, Fourier Transform Infrared Spectroscopy (FTIR) transmittance spectra are measured and analyzed for undoped and doped polymeric thin films to pinpoint the major vibrational modes in the spectral range (500 and 4000 cm-1), as well as, the nature of network bonding in both systems. Thermal stability of thin films is investigated by performing thermogravimetric analysis (TGA). The TGA thermograms confirm that both doped polymeric thin films are thermally stable at temperatures below 110°C which enables them to be attractive for a wide range of optical and optoelectronic applications. Our results indicate that optical, vibrational and thermal properties of both polymeric thin films can be tuned for specific applications by the appropriate corporation of particular concentrations of CuO-NPs.

Clustered regularly interspaced short palindromic repeats or CRISPR, one of the major technological tools from nature's toolbox, has revolutionized the scientific world with its potential use in humans and plants. CRISPR Cas9 was first known as an adaptive immune system of bacteria. It is a system that cleaves foreign DNA. It has been exploited to be used as a genome editing tool for correcting genetic diseases in humans, for plants to create stress-resistant plants, and for a variety of different purposes. This review provides a basic overview of its applications in different areas of biological research. It has immense potential for a variety of researches, but it's still a mystery for science. It feels like scientists just know a tip of an iceberg.

The Coronavirus disease due to SARS-CoV-2 emerged in Wuhan city, China in December 2019 and rapidly spread more than 200 countries as a global health pandemic. There are more 3 million confirmed cases and around 207,000 fatalities. The primary manifestation is respiratory and cardiac but neurological manifestations are being reported in the literature as case reports and case series. The most common reported symptoms to include headache and dizziness followed by encephalopathy and delirium. Among the complications noted are Cerebrovascular accident, Guillian barre syndrome, acute transverse myelitis, and acute encephalitis. The most common peripheral manifestation was hyposmia. It is further noted that sometimes the neurological manifestations can precede the typical features like fever and cough and later on typical manifestations develop in these patients. Hence a high index of suspicion is required for timely diagnosis and isolation of cases to prevent the spread in neurology wards. We present a narrative review of the neurological manifestations and complications of COVID-19. Our aim is to update the neurologists and physicians working with suspected cases of COVID-19 about the possible neurological presentations and the probable neurological complications resulting from this novel virus infection.

Noncoding RNA regions have emerged as pivotal players in the regulation of various cellular processes, and their involvement in HIV/AIDS pathogenesis is an evolving field of research. This review article delves into the intricate interplay between noncoding RNA regions and AIDS, shedding light on the diverse mechanisms by which these RNA molecules influence viral replication, immune responses, and disease progression. The review highlights recent discoveries, potential therapeutic applications, and the challenges ahead, illustrating the promising prospects of noncoding RNA research in the context of HIV/AIDS.

Non-coding RNA regions have long been considered the "dark matter" of the genome, with their significance in gene regulation remaining enigmatic. However, recent advances in genomics and molecular biology have illuminated the pivotal role that non-coding RNA regions play in the fine-tuned orchestration of hemoglobin expression. Hemoglobin, the oxygen-carrying protein vital for life, is tightly regulated, and any disruption in its production can lead to severe medical conditions, such as hemoglobinopathies. This review delves into the intricate world of non-coding RNA regions, exploring how they act as master conductors in controlling hemoglobin gene expression. We will discuss various classes of non-coding RNAs, including long non-coding RNAs, microRNAs, and circular RNAs, and their specific mechanisms in fine-tuning hemoglobin levels. Additionally, we will highlight emerging therapeutic approaches that target non-coding RNA regions to ameliorate hemoglobin-related disorders. Understanding the critical role of non-coding RNA regions in hemoglobin regulation opens new avenues for precision medicine and gene therapies, offering hope for those affected by hemoglobinopathies and related conditions. This comprehensive review sheds light on the significance of these non-coding RNA regions, demonstrating that the "silent" players in the genome are, in fact, the conductors of harmony in the symphony of hemoglobin regulation.

This study explores the potential of Eisenia fetida (Savigny) in vermicompost production within vermipits during winter months in the Rampur region of Uttar Pradesh, India. The vermipits were inoculated with 0.33 kg of E. fetida per pit, against the recommended rate of inoculation for assessment of real-time potential of earthworm on seasonal and regional grounds. The results revealed a significant increase in earthworm population, with three times production (4.1 kg) of the inoculated number (1.0 kg). The productivity dynamics of compost vs E. feida revealed a notable threefold and fourfold effectiveness, respectively. This dual advantage signifies the success of composting process, with the increased worm population indicating enhanced decomposition. The study attributes the combination of regional and edaphic factors viz., sandy loam soil with high humus content and good water passage, facilitating earthworm survival, reproduction and decomposition of agricultural waste. The loose and perforated soil structure allowed easy penetration of earthworms, transforming the soil into fertile compost. The research emphasizes the importance of soil moisture of semi-arid ecosystems thus highlighting the seasonal significance governing earthworm activity. The study provides insights into the mechanical ability of earthworms, its sensitivity to soil compaction and the influence of high hydration of the region. Inoculation during the winter period indicates increased earthworm activity setting the stage for enhanced compost production in the upcoming hot periods of summer months. The findings suggest that optimizing vermicomposting practices with altered feeding stocks, could further improvise compost and earthworm production and productivity in subsequent seasons. The study contributes for sustainable utilization of E. fetida in composting, its regional and seasonal efficacy turns trash to treasure for enhanced agricultural efficacy

The article outlines a creative approach by fusing ideas from fuzzy contractions, graph mappings, and Kannan mappings to create a brand-new notion known as "Kannan-graph-fuzzy contraction." This combination of concepts makes it possible to create a unique framework for resolving real-world issues controlled by nonlinear models. It is anticipated that using Kannan-graph-fuzzy contractions will offer a fresh approach to discussing solution existence in situations where these ideas overlap. This strategy might have a significant impact on a lot of real-world applications, proving how practical multidisciplinary techniques are for tackling issues in the real world originating from technology and engineering. The article includes several illustrated examples based on computer simulations, making the results more explicit.

The eruption of COVID-19 patients in 215 countries worldwide has urged for robust predictive methods that can detect as early as possible the size and duration of the contagious disease and also providing precision predictions. In much recent literature reported on COVID-19, one or more essential parts of such investigation were missed. One of the crucial elements for any predictive method is that such methods should fit simultaneously as much data as possible; these data could be total infected cases, daily hospitalized cases, cumulative recovered cases, and deceased cases, and so on. Other crucial elements include sensitivity and precision of such predictive methods on the amount of data as the contagious disease evolved day by day. To show the importance of these aspects, we have evaluated the standard SIRD model and a newly introduced Gaussian-SIRD model on the development of COVID-19 in Kuwait. It is observed that the SIRD model quickly picks up the main trends of COVID-19 development, but the Gaussian-SIRD model provides precise prediction a longer period of time.

One of the special trends in health care is the increasing availability of data and services to the cloud, especially for convenience (for example, providing a complete patient medical record without interruption) and savings (for example, economic issues). Management of health care data). However, there are limitations to using common cryptographic prototypes and access control models to address security and privacy concerns in an increasingly cloudy environment. In this paper, we explore the potential and capacity of using China's Blockchain technology to protect health care data hosted in the cloud. We also explain the real challenges of such an approach and further research is needed. Health care is a highly data-dependent domain, with large amounts of data being created, published, stored and accessed daily. For example, data are created when a patient undergoes a number of examinations (such as computed tomography or computed tomography scans) and the data need to be sent to the radiologist and then to a physician. The visit results are then stored in the hospital, and then need to be accessed later by another physician at another hospital within the network. It is clear that technology can play an important role in improving the quality of care for patients (for example, using data analytics to make informed medical decisions) and potentially costing more by allocating resources more efficiently in terms of personnel, equipment, etc. , Reduce. For example, paper-based data extraction is difficult to extract into systems (for example, it is costly and may involve data entry errors), archiving them and accessing them as needed is costly. These challenges may cause medical decisions to be incomplete, requiring repeated tests for missing information or missing data stored in another hospital in another state or country (at the expense of increased costs and no convenience). (For patients) and so on. Because of the nature of the industry, it is important to ensure the security, privacy and integrity of health care data. As a result, there is definitely a need for a secure and secure data management system.

This study was to designed to develop sorafenib-loaded polymeric nanoparticles, surface-modified with pluronic F-127 for the effective treatment of hepatocellular (HCC) and renal cell carcinomas (RCC). Poly lactic coglycolic acid (PLGA) was used to encapsulate different concentrations of sorafenib by a simple modified solvent evaporation method applying pluronic F-127 as a surfactant and coating agent. The preformulation and characterization studies were conducted to evaluate the incompatibilities among sorafenib, PLGA and pluronic F-127, and physicochemical properties of the formulations, respectively. The sizes of the coated and plain PLGA nanoparticles were ~140 ± 14.7 nm and ~ 120 ± 10.1 nm, respectively. It has been confirmed from the in vitro release studies that PLGA sustained the release of sorafenib, avoiding the initial burst release, while the in vivo studies demonstared that surface-modified nanoparticles have greater affinity in the target aorgans than plain PLGA nanoparticles and free drug keeping the dose constant (20 mg/kg body weight). The delivery of sorafenib-loaded polymeric PLGA nanoparticles into the target tissues and their pharmacokinetic parameters have been improved significantly compared to the reported formulations.

To handle the huge amount of data generated by IoT devices, Big Data processing tools make it easier. This paper discusses the Big Data concept and its main V’s characteristics. It further describes IoT-enabling technologies; nominally cloud computing such as SaaS and PaaS. The centralization and infrastructure of Big Data systems, and how Cloud Computing gives a platform access to the data from anywhere. The paper explores IoT with big data architectural solutions for various use cases across the healthcare and transportation sectors.

In this paper, we discussed the motion of neutral and charged particles in Schwarzschild black hole immersed in an electromagnetic universe (SEBH). The SEBH represents a mass M coupled to an external electromagnetic field that was derived from the metric of colliding electromagnetic waves with double polarization. Our study examine how the external electromagnetic field affects the trajectory of neutral and charged particles. First, the trajectories of both photon and test particle are studied. Then, the exact solutions for the trajectories are obtained in terms of the Jacobi-elliptic integrals for all possible energy and angular momentum of test particle and photon. We have also discussed the motion of charged particle and obtained the radius of the innermost circular orbit (ISCO). It is especially interesting when the charge sign is positive since this creates a conflict between gravitational (attraction force) and electric (repulsion force). Furthermore, we discuss the Lyapunov exponent and the effective force influencing particles in SEBH spacetime.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

This study explored the living situations, financial conditions, religious obligations, and social distancing of Muslims during the covid 19 pandemic. In total, 20 Muslim community members living in the Kanto region were recruited, 15 of them were included in the in-depth qualitative and five in the focus group interviews. The Snowball method was used, and the questionnaires were designed into four themes. The audio/video interviews were conducted via Zoom and NAVIO was used to analyse the data thematically. The major Muslim events were cancelled, and the recommended physical distancing was maintained during the prayers at home and in the mosques. The Japanese government's financial support to each person was a beneficial step towards social protection, which was highlighted and praised by every single participant. Regardless of religious obligations, the closer of all major mosques in Tokyo demonstrates to the Japanese community how serious they are about adhering to the public health guidelines during the pandemic. This study highlighted that the pandemic has affected the religious patterns and behaviour of Muslims from inclusive to exclusive in a community and narrated the significance of religious commitments.

This paper presents a methodology for the integration of Building Information Modeling (BIM) and Life Cycle Cost Analysis (LCCA) to assess the economic implications of designing aging-in-place (AIP) homes at the conceptual stage. With the global increase in the aging population, there is an increased demand for housing solutions tailored to the needs of elderly individuals. Focusing on the importance of the early phase of design, this study aims to improve the process of making efficient decisions by providing a comprehensive assessment of the life cycle costs associated with AIP homes. The study introduces a semi-automated model for the economic evaluation of AIP homes, enabling the estimation of costs throughout the houses’ entire life cycle, from design and construction to operation, maintenance, and eventual renovation or disposal. The said model facilitates the exploration of the long-term economic feasibility of design’s related decisions with an emphasis on the importance of considering the life cycle costs early during the design process to optimize the functionality and economic viability. By investing in accessible and universal design features upfront, the initial costs for modifications can lead to long-term savings by reducing the need for extensive retrofits. The model can easily do comparison between different design alternatives in terms of their lifecycle costs, allowing designers to assess the financial impact of using important features in their design such as wider doorways, accessible bathrooms, and elevators. Overall, this study provides valuable insights for designers and homeowners about the economic aspects of designing AIP homes as a support for efficient decision-making during the early stages of the design process.

In computer networks, loss of data packets is inevitable, in particular, because of the buffer memory overflow of at least one of the nodes located on the path from the source to the receiver, including the latter. Such losses associated with overflows are hereinafter referred to as congestion of network nodes. There are many ways to prevent and eliminate overloads; these methods, in the majority, are based on the management of data flows. A special place is taken by the maintenance of packages, taking into account their priorities. The article considers a number of original technical solutions to improve the quality of control and reduce the required amount of buffer memory of network nodes. The ideas of these solutions are quite simple for their implementation in the development of appropriate software and hardware for telecommunication devices.

Background: Delivery of quality family planning services depends on availability of skilled health care providers, which is often a challenge in Low- and middle-income countries. This study evaluates the effects of a targeted training program on family planning services delivered by the Lady Health Workers (LHWs) in six districts of Punjab, Pakistan. The primary goal was to enhance the quality and accessibility of family planning services, recognizing the pivotal role of LHWs in community health. Methods: Using a robust panel data difference-in-differences (DiD) approach, we analyzed the electronic medical records (EMR) of 1,410 LHWs over a nine-month period. This timeframe in-cluded both pre-training (July to December 2022) and post-training (April to June 2023) phases. Our assessment focused on the impact of training on five outcome variables: the number of follow-up clients, the number of Intrauterine Contraceptive Device (IUCD) clients, the number of condom clients, the number of modern method clients, and the number of injection clients. We also con-sidered control variables such as LHW age, LHW education, the number of eligible couples in each LHW's catchment area, and a categorical variable for the districts. Results: The positive and statistically significant (p<0.05) coefficients across various service cat-egories – Follow Up Clients [Coeff: 1.00, CI: (0.30 - 1.70)], IUCD Clients [Coeff: 0.23, CI: (-0.01 - 0.46)], Condom Clients [Coeff: 1.41, CI: (0.97 – 1.86)], Modern Method Clients [Coeff: 1.82, CI: (0.96 – 2.68)], and Injection Clients [Coeff: 0.32, CI: (0.14 – 0.50)]. These findings indicate enhanced productivity among LHWs who have received training, with results significant at the 95% con-fidence interval (CI). Conclusion: The study highlights the effectiveness of targeted training programs in boosting family planning services at the community level and offers insightful implications for policy-makers and health practitioners. While focused on six districts in Punjab, these promising results emphasize the need for ongoing training and support for frontline health workers to bolster family planning initiatives.

Aravalli Mountain Range is an example of erosional mountains, trending NE-SW, shows numerous faults and lineaments. Udaipur area, situated south-east part of the mountain, is considered as tectonically active. So the main objective is to study relative tectonic activity of the Ahar watershed of Udaipur, Rajasthan, India. To assess relative tectonic activity of the area, geomorphic indices such as stream length gradient index (SL), asymmetry factor (Af), basin shape (Bs), valley floor width to valley height ratio (Vf), mountain front sinuosity (Smf), hypsometic integral (Hi), hypsometric curve and transverse topographic symmetry factor (T) is applied. DEM (SRTM), Google earth image and enhanced image of Landsat TM (2008) is used to extract linear features. Result of these geomorphic indices of each sub-watersheds are used to divide area from low to high relative tectonic activity classes, expressed as relative tectonic active index (Iat) and according to Iat value the sub watershed UDSW2, 3 and 4 is tectonically relatively more active than remaining part of the area. Field validation associated with evidences highlighted by using geomorphic indices as well as stream deflrction and lineament analysis reveals that the Ahar watershed of Aravalli Range, particularly the north-western flank, is most affected by tectonic activity.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

Online identity-based theft is known to be one of the most serious and growing threats to victims, such as individuals and organizations, over the last 10 years due to the enormous economic damage these crimes have caused. The availability of personal information on the Internet has increased the chances of this cyber-crime. Online identity theft crime is the result of a combination of cyber-crimes on the one hand and lack of awareness and training of users on the other hand to protect personal data on the other. Education and awareness, which also contributes to early detection, is the strongest tool for consumers to safeguard themselves from online identity fraud. This paper provides a comprehensive explanation of online identity theft, the various approaches that thieves use to attack individuals and organizations and the types of fraud involved in this cyber-crime. The aim of this research is to evaluate the need for a reformulation of the concept of identity theft in order to be compatible with the evolution of behaviors and fraud.

This study discusses the experimental assessment of the in-plane mechanical behavior of a multi-leaf stone masonry wall built from cut stone and reinforced with metal connectors (cramps and dowels). The wall, inspired by conventional multi-leaf stone walls, is meant for use in modern stone masonry buildings. The wall is constructed from two parallel load-bearing walls with a cavity between them, which aims to conceal the installation and insulation needed in modern buildings. The load-bearing walls are connected with cramps and dowels at certain intervals so that the wall works as a single section against horizontal and vertical loads. To characterize the in-plane behavior of the proposed wall, compressive, triplet, and diagonal compression tests were conducted to investigate the compressive strength, shear strength, modulus of elasticity, stiffness, ductility, and energy absorption of the wall. Compared with dry and mortar joint walls, the use of dowels increased the initial shear capacity of the wall by 11 and 19 times, respectively. The application of cramps without curving channels inside the individual stone elements decreased the compressive strength by 18%. The energy absorption of the designed walls with metal connectors was substantially increased to that of the specimens representing conventional stone walls. The results obtained show the applicability of the wall due to its higher shear strength and minimal drop in compressive strength, which is within acceptable limits.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

The objective of this study is to determine the relationship between body condition score (BCS) and body carcass fat (BCF) of ewes at two key stages of the production cycle. Data were collected from 88 Coopworth ewes including BCS measurements manually evaluated by the farm manager, BCF measurements determined by computerized tomography (CT) and body parameter measurements automatically determined by an image processing application. Artificial neural network (ANN) statistical analysis method was used to develop a relationship between the body parameters and the BCF with an r2=0.96 and RMSE=1.01 using all top and side variables.

Background: MERS-CoV is a zoonotic virus that have emerged in humans in 2012 and caused severe respiratory illness with mortality rate of 34.4%. Since its appearance, MERS-CoV have been reported in 27 countries and most of these cases were in Saudi Arabia. So far, dromedaries are considered to be the intermediate host and the only known source of human infection. Method: This study was designed to determine the seroprevalence and the infection rate of MERS-CoV in slaughtered food-camels in Riyadh, Saudi Arabia. A total of 171 nasal swabs along with 161 serum samples were collected during the winter; from January to April 2019. Nasal swabs were examined by Rapid test and RT-qPCR to detect MERS-CoV RNA, while serum samples were tested primarily using S1-based ELISA Kit to detect MERS-CoV (IgG) antibodies and subsequently by MERS pseudotyped viral particles (MERSpp) neutralization assay for confirmation. Genetic diversity of the positive isolates was determined based on the amplification and sequencing of the spike gene. Results: Our results showed high prevalence (38%) of MERS-CoV infection in slaughtered camels and high seropositivity (70.81%) during the time of the study. These data indicate previous and ongoing MERS-CoV infection in camels. Phylogenic analysis revealed relatively low genetic variability among our isolated samples. When these isolates were aligned against published spike sequences of MERS-CoV, deposited in global databases, there was sequence similarity of 94%. Conclusion: High seroprevalence and high genetic stability of MERS-CoV in camels indicating that camels pose a public health threat. The widespread of MERS-CoV infections in camels increases the risk of future zoonotic transmission into people with direct contact with these infected camels. This study confirms re-infections in camels, highlighting a challenge for vaccine development when it comes to protective immunity.

Despite the 12-lead electrocardiogram (ECG) being the gold standard in evaluating clinical presentations of arrythmias of various kinds, several notable limitations, namely in accuracy and localization, have recently garnered concern with respect to administering appropriate therapeutic measures. The following text puts these limitations under the spotlight, highlighting the difficulty and challenging nature of standard ECG analysis and therapeutic measures, while simultaneously showing a novel body surface electrocardiographic mapping system that utilizes 3D spatial imaging and pinpoint localization algorithms in order to compensate for the shortcomings of the standard ECG, thereby providing higher precision data collection. We provide a brief overview of the novel device in a selection of arrhythmic demographics, along with its validity and reliability, while illustrating the benefits and positive outcomes of its utility.

The new emergence and re-emergence of arbovirus infections vectored by Aedes mosquitoes have been spread across Southeast Asia, Central Africa, United States, tropical Oceania and become a major of public health concerns. These arbovirus diseases found to have a similar vector, symptoms of the diseases and environments. The situation has become complicated without any specific vaccine or treatment for the diseases. As far as we concern, vector control is the best defense with many challenges, a scattered breeding site and biological behavioral sometimes, more difficult to control. Herein, we present a review of studies on current techniques proposed to combat arbovirus infections vectored by Aedes mosquitoes. A crucial gap in a vector control program is the inability to eliminate and destroy the cryptic breeding site by using conventional control methods. The idea and proper concept of using mosquitoes to bring insecticide to their oviposition site had been getting more interest in people to explore. Autodissemination is a self-delivery technique by manipulating the behavior of mosquitoes, carrying the insecticide and disseminate to cryptic breeding sites. This technique has shown a promising result in some countries and can be considered as additional tools in a vector control program

Big Data classification has recently received a great deal of attention due to the main properties of Big Data, which are volume, variety, and velocity. The furthest-pair-based binary search tree (FPBST) shows a great potential for Big Data classification. This work attempts to improve the performance the FPBST in terms of computation time, space consumed and accuracy. The major enhancement of the FPBST includes converting the resultant BST to a decision tree, in order to remove the need for the slow K-nearest neighbors (KNN), and to obtain a smaller tree, which is useful for memory usage, speeding both training and testing phases and increasing the classification accuracy. The proposed decision trees are based on calculating the probabilities of each class at each node using various methods; these probabilities are then used by the testing phase to classify an unseen example. The experimental results on some (small, intermediate and big) machine learning datasets show the efficiency of the proposed methods, in terms of space, speed and accuracy compared to the FPBST, which shows great potential for further enhancements of the proposed methods to be used in practice.

The water quality of the river is becoming deteriorated due to human interference. It is essential to understand the relationship between human activities and land-use types to assess the water quality of a region. GIS has the latest tool for analyzing the spatial correlation. Land use land cover and change detection is the best illustration to show the human interactions on land features. The study assessed water quality index of upper Ganga River near Haridwar, Uttarakhand and spatially correlated them with changing land use to reach a logical conclusion. At the upper course of Ganga along 78 Km long from Kaudiyala to Bhogpur, water samples were collected from five stations. For water quality index the physicochemical parameters like pH, EC, DO, TDS, CaCO3-, CaCO3, Cl¯, Ca++, Mg++, Na+, K+, F-, Fe2+ were considered. The result of the spatial analysis was evaluated through error estimation and spatial correlation. The root mean square error between spatial land use and water quality index of selected sampling sites was estimated as 0.1443. The spatial correlation between land-use change and site-wise differences in water quality index has also shown a high positive correlation with R² = 0.8455. The degree of positive correlation and root mean square error has strongly indicated that the water quality of the river at the upper course of Ganga is highly impacted through human activities.

Bread wheat (Triticum aestivum L.) is staple of Pakistani people. However, its yield at farmer field is low as compared with its genetic potential. Integration of various crop and soil management strategies might be an option to enhance wheat productivity at farmer field. This 2-year experiment was conducted to check the influence of combine application of natural plant water extracts and biochar on the productvity of wheat during the winter season of 2015-16. The experiment consisted of seven treatment viz. (1) control (2) application of biochar (0.18 kg pot-1) alone, (3) application of sorghum water extract (SWE) alone, (4) application of moringa water extract (MWE) alone, (5) application of biochar + SWE, (6) application of biochar + MWE, (7) application of biochar + SWE+MWE. The results revealed that application of both crop water extracts in combination with biochar improved the growth and grain yield of wheat. Use of MWE in combination with biochar enhanced the grain weight, grain number and grain yield of wheat by 44, 14, and 24%, respectively than the control treatment. In crux, use of MWE in combination with biochar might be a viable option to improve the productivity of bread wheat.

The canonical decomposition of a bipartite graph is a new decompositionmethod that involves three operators, parallel, series and K+S. The class of weak bisblit graphs is totally decomposable with respect of these operators, and the class of bicographs is totally decomposable with respect of parallel and series operators. We prove in this paper that the class of bipartite (P_6,C_6)-free graphs is exactly the class of bipartite graphs that are totally decomposable with respect of parallel and K+S operators. We simplify the recognition algorithm of weak-bisplit graphs to adepte with bipartite (P_6,C_6)-free graphs. As a result of this adapted algorithm, we prsent efficient solutions in this class of graphs for two optimization graph problems, the first is the maximm balanced bi-clique problem and the the second is the maximum independent set problem.

Background: A person living with HIV / AIDS bargains with stressors such as discrimination, stigma depression, and several psychological impacts. The stressors experienced by people with HIV/ AIDS will certainly have an impact on daily activities, welfare, and management of medications which in general will have an impact on the quality of life. To deal with these stressors, it is necessary to have good and proper coping from within the PLWHA. Coping strategies need to be owned and carried out by PLWHA in order to respond adaptively to the stressor conditions experienced. Purpose: The aim of this review is to describe the stress experienced and the coping strategies used among PLWHA. Methods: This literature review used keywords in the search for international references are coping strategy, stressor, HIV-AIDS. Inclusion criteria: selection of titles that are relevant to the formulation of the problem and objectives, full-text articles in English, articles published from 2019 to 2021. The exclusion criteria used were coping strategy articles that did not involve HIV patients. Search references from electronic database sources namely ProQuest, CINAHL, and ScienceDirect.Six articles that are deemed worthy of analysis are then discussed or analyzed. Results: Age, gender and sexual orientation have contributed to the emerging stressor among PLWHA. The internal and external coping strategies focusing on the problem are important for PLWHA in handling the stressor. Conclusion: People with HIV-AIDS have many stressors in their lives, but they also have proper coping strategies depending on their internal and external conditions.

The Storm Water Management Model (SWMM) was used to evaluate the impact of urbanization, climate change, and implementation of Low Impact Developments (LIDs) at the Mahabad Dam watershed, Iran. Several scenarios of urbanization, with and without climate change impacts, in different locations were defined, including near outlet, middle, far end, and whole watershed. Climate change was considered to change the intensity of rainfall and increase evaporation. Vegetative swales were implemented as LIDs to evaluate their applicability to reduce pollutant loads. Digital Elevation Model (DEM) of the area was input into ArcGIS, and the watershed was delineated using the ArcSWAT extension to identify topographic features. Water quality properties were defined in the software, and each scenario was run for a twelve-hour simulation. The results indicated that urbanization affects the imperviousness of sub-catchments, and location of urbanization affects the amount and timing of runoff and pollutant yields. Fifty-percent urbanization near the watershed outlet resulted in 23.1% and 27.4% increases in runoff and pollutant loads, respectively. Fifty-percent urbanization in the middle resulted in 28.8% and 35.4% increases in runoff and pollutant loads; and, at the far end, 23.1% and 3.9% increases in runoff and pollutant loads were the result; Fifty-percent urbanizing the whole watershed gave 58.6% and 66.3% increases in runoff and pollutant loads, respectively; Under climate change scenarios (higher intensity, shorter duration rainfall) peaks occurred earlier. Moreover, results showed LIDs decreased pollution loads up to 25%.

The synchronous generator, as the main component of power systems, plays a key role in these system’s stability. Therefore, utilizing the most effective control strategy for modeling and control the synchronous generator results in the best outcomes in power systems’ performances. The advantage of using a powerful controller is to have the synchronous generator modeled and controlled as well as its main task i.e. stabilizing power systems. Since the synchronous generator is known as a complicated nonlinear system, modeling and control of it is a difficult task. This paper presents a sum of squares (SOS) approach to modeling and control the synchronous generator using polynomial fuzzy systems. This method as an efficacious control strategy has numerous superiorities to the well-known T–S fuzzy controller, due to the control framework is a polynomial fuzzy model, which is more general and effectual than the well-known T–S fuzzy model. In this case, a polynomial Lyapunov function is used for analyzing the stability of the polynomial fuzzy system. Then, the number of rules in a polynomial fuzzy model is less than in a T-S fuzzy model. Besides, derived stability conditions are represented in terms of the SOS approach, which can be numerically solved via the recently developed SOSTOOLS. This approach avoids the difficulty of solving LMI (Linear Matrix Inequality). The Effectiveness of the proposed control strategy is verified by using the third-part Matlab toolbox, SOSTOOLS.

The current study was formulated with the aim of assessing the impact of the Extent of Drug addiction on the Family environment and interventions for drug-addicted youth in rural areas of Dir Lower Khyber Pakhtunkhwa, Pakistan. The study comprised a dependent variable (Extent of Drug addiction) and an independent variable (Family Environment). A sample size of 266 was randomly selected for primary data collection through structured interviews. The collected information was evaluated through descriptive analysis (frequency and percentage distribution) and inferential analysis, specifically utilizing the Chi-square Statistical Test. The study concluded that drug addiction among youth has an adverse impact on the family environment, leading to instability and violent behavior. Further, families of drug-addicted youth experience a high level of dissatisfaction in relationships, often culminating in divorce. Similarly, the families of drug-addicted are characterized by low cohesion, role conflict, and tolerance. Thus, the government should formulate polices and strategies for the prevention of drug addiction, with speedy implementation across all institutional dynamics, including family. Moreover, It is also crucial to rehabilitate the lifeblood of a nation (youth) in terms of socio-economic, emotional and psychological growth. These recommendations were put forward in the light of the current study.

The second-order factor effect of burner optical ports and edge inter-matrices (EIM) and the first-order factor of pressure on the soot formation process and behavior of premixed sooting flames in a high-pressure burner are numerically investigated here. Three-dimensional computational fluid dynamics (CFD) simulations of a premixed flame C₂H₄/air at p = 1.01 and 10 bar using a one-step chemistry approach are first performed to justify the satisfied predictability of the prospective axisymmetric two-dimensional (2D) and one-dimensional (1D) simulations. The justified 2D simulation approach shows the generation of an axial vorticity around the EIM and axial multi-vorticities due to the high expansion rate of burnt gases at the high pressure of 10 bar. This leads to the development of axial multi-sooting zones, which are manifested experimentally by visible luminous soot streaks, and to the boosting of soot formation conditions of a relatively low-temperature field, < 1800 K, and a high mixing rate of gases in combustion around and above the EIM location. Nevertheless, a tolerable effect on the centerline soot volume fraction (f_V) profile, f_V < 3%, is manifested only at high heights above the burner of the atmospheric sooting flame C₂H₄/air ϕ = 2.1, and early at the high pressure of 10 bar of this flame, f_V < 10%. Enhancing the combustion process reactivity by decreasing the rich equivalence ratio of the fuel/air mixture and/or rising the pressure results in the prior formation of soot precursors, which shifts the sooting zone upstream.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

Peste des Petits Ruminants (PPR) is one of the major transboundary animal diseases that severely impact livestock production and trade worldwide. An investigation was carried into the seroprevalence and risk factors of PPR in small ruminants, camels, and wild ruminants in Bahrain. A total of 1240 serum samples were collected from 119 sheep flocks and 1224 serum samples from 125 goat herds. In addition, 100 sera from camels and 38 sera from wild ruminants, were collected. Serum samples were tested for the presence of PPR specific antibodies using a competitive ELISA. Flock management and health information of the flocks and herds were collected using a semi-structured questionnaire. The individual prevalence of PPR in sheep and goats was 26% and 25.5%, respectively. The flock or herd level prevalence of PPR was 22.7% and 29.6% in sheep and goats, respectively. None of the tested camels or wild ruminants were positive for PPR-specific antibodies. Sheep and goats from the Northern governorate were more likely to be seropositive to PPR than in other governorates. On the individual animal level, the univariate analysis suggested; age (&lt;12 months), sex (male), and health status (weak animals) as risk factors for PPR seropositivity. On the flock/herd level, the multivariable logistic regression analysis identified large flock/herd size and semi-intensive farming as risk factors for PPR seropositivity.

Lifestyle is the primary prevention of diabetes, especially type-2 diabetes (T2D). Nutritional intake of olive oil (OO), the key Mediterranean diet component has been associated with the prevention and management of many chronic diseases including T2D. Several OO bioactive compounds such as monounsaturated fatty acids, and key polyphenols including hydroxytyrosol and oleuropein, have been associated with preventing inflammation and cytokine-induced oxidative damage, glucose lowering, reducing carbohydrate absorption and increasing insulin sensitivity and related gene expression. However, research into the interaction of OO nutraceuticals with lifestyle components, especially physical activity is lacking. Promising postprandial effects have been reported when OO or other similar monounsaturated fatty acids was the main dietary fat compared with other diets. Animal studies have shown a potential anabolic effect of oleuropein. Such effects could be further potentiated via exercise, especially strength training, which is an essential exercise prescription for individuals with T2D. There is also an evidence from in vitro, animal and limited human studies for a dual preventative role of OO polyphenols in diabetes and cancer, especially that they share similar risk factors. Putative anti-oxidative and anti-inflammatory mechanisms and associated gene expressions resulting from OO phenolics, have produced paradoxical results making suggested inferences from dual prevention T2D and cancer outcomes difficult. Well-designed human interventions and clinical trials are needed to decipher such a potential dual anti-cancer and anti-diabetic effects of OO nutraceuticals. Exercise combined with OO consumption, individually or as part of a healthy diet is likely to induce reciprocal action for T2D prevention outcomes.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

In this paper, a local meshless method (LMM) based on radial basis functions (RBFs) is utilized for the numerical solution of various types of PDEs, due to the flexibility with respect to geometry and high order of convergence rate. In case of global meshless methods, the two major deficiencies are the computational cost and the optimum value of shape parameter. Therefore, research is currently focus towards localized radial basis function approximations, as the local meshless method is proposed here. The local meshless procedures is used for spatial discretization whereas for temporal discretization different time integrators are employed. The proposed local meshless method is testified in terms of efficiency, accuracy and ease of implementation using regular and irregular domains.

Abstract: The Internet of Things (IoT) has witnessed rapid and widespread adoption across various domains, including transportation, healthcare, education, agriculture, urban planning, smart homes, and more. Despite its transformative potential, this pervasive deployment of IoT devices has introduced new challenges, particularly concerning security and privacy threats such as unauthorized data access and device breaches. The excessive usage of these technological devices, coupled with the absence of robust security and privacy systems for user data, calls for a comprehensive approach to address these issues. In this study, we propose a novel framework designed to analyze, audit, test, and detect potential vulnerabilities within IoT environments and applications. The central components of the proposed framework include a machine learning algorithm for data classification and attack detection, along with the integration of Blockchain technology to enhance security measures. Specifically, the framework performs an in-depth analysis of user data to identify potential security or privacy vulnerabilities. Additionally, it conducts rigorous testing of smart services and automated data-collecting devices. To evaluate the effectiveness of our classification algorithm, we conducted a comprehensive implementation on a real-world IoT dataset. The results showcased the efficiency and accuracy of our approach in detecting and mitigating potential threats. Furthermore, based on our research findings, we provide valuable recommendations for enhancing security and privacy in IoT ecosystems. We also highlight emerging trends in the security and privacy domains, which can serve as valuable insights for researchers and practitioners. In conclusion, our proposed framework offers a robust and proactive approach to address the security and privacy challenges, such as unauthorized data access and device breaches posed by the widespread adoption of IoT devices. By combining machine learning algorithms and Blockchain technology, we contribute to safeguarding user data and fostering a secure environment for IoT applications. This study lays the groundwork for further advancements in the realm of IoT security and privacy, ensuring a safer and more resilient IoT landscape for the future.

Catalase can decompose hydrogen peroxide in plants under controlled and stressed condi-tions. In a stressed environment, the increase in hydrogen peroxide production makes catalase activity a major defense system for plant growth. The current study was conducted to evaluate the catalase activity of pre-isolated and identified bacterial strains Bacillus aryabhattai (AN30), Bacillus megaterium (AN24), Bacillus megaterium (AN31) and Bacillus megaterium (AN35) and their potential for rice seedlings growth promotion. These strains were characterized for quantita-tive catalase, urease, siderophores, and exopolysaccharides production using LB media. Sub-sequently, the effectiveness of these strains was checked by quantifying the catalase activity in the rhizosphere of rice seedlings. Furthermore, the catalase activity was quantified in the roots and shoots of rice seedlings. Plant growth parameters were also studied in a growth room trial. The strain AN24 showed the maximum catalase activity (1.36 mol cm-1), urease ac-tivity (1.35 mol cm 1), exopolysaccharides (4.20 µg mL-1), and siderophores (2.32%) production in LB media. All tested strains showed significantly higher catalase activity in soil compared to control. Among sole application, strain AN24 showed better results; however, consortium application of strains AN24+AN30+AN35+AN31 showed the maximum increase in catalase ac-tivity in the rhizosphere of rice seedlings. Moreover, consortium application of AN24+AN30+AN31+AN35 resulted in the highest increase in catalase activity, dry biomass of shoots and roots, shoot and root length of rice seedlings. The results showed that a consortium of these Bacillus strains with catalase activity has greater potential to enhance an antioxidant defense system and growth promotion of rice seedlings. However, further experimentation under natural conditions is required before using these strains as potential bioinoculants for improving the rice growth and yield.

The Soil Conservation Service - Curve Number (SCS-CN) method is extensively used to calculate the runoff from rainfall over a large catchment over the world. Slope is an important criterion for runoff but a very few attempts have been made to evaluate the effect of slope on the CN with runoff potential. The objective of this paper is to summarise the historical review on the effects of slope on CN and runoff potential in various regions by the hydrologists. This paper also depicts that how the various researchers proved the importance of consideration of slope for CN and runoff estimation. In addition, paper highlights the key features of research in future like to classify the watersheds on slope based CN, accurate Antecedent Moisture Condition (AMC) and proper initial abstraction in the various regions etc. Considering these parameters an accurate runoff estimation can be predicted and managed properly in the urban watersheds.

Background: Serious games are conceptualized as a broad topic and overlap segments of more modern forms of education: e-learning, edutainment, game-based learning, and digital game-based learning. Serious Games aligns with digitalization and the modern era and creates novel opportunities for learning and assessment in medical education. Escape rooms, a type of serious games, merge mental and physical aspects to reinforce critical skills useful in daily life. It challenges logic and reasoning and demands careful analysis of situations to correlate and solve different stages of the escape room under pressurized, timed conditions. Furthermore, it serves as an adequate environment to build problem-solving skills, communication skills, and leadership skills through the collaboration of people to achieve a common goal. The aim of this study was to investigate the applications of escape rooms in Medical Education. Method: This study investigated the applications of escape rooms in medical education. Serious games are expanding in education and have attained great relevance due to their intriguing and intrinsically motivating attributes. Within serious games, we focused on escape rooms in which participants are locked in a room, faced with puzzles that must be solved to ‘escape the room’. Compiling the data from the first 100 hits of medical application of escape rooms, we found 72 cases and categorized them by year, specialty, participants structure, simulation experience, and design. Results: We reported on escape rooms in medical education by the year in which they were reported, the medical specialty, the participant structure, grouped or individual, the experience design; real, hybrid, or digital, and the modality of the delivery. 72% of the escape rooms focused on four main areas: nursing education (25.0%), emergency medicine (22.2%), pharmacy (12.5%), and interprofessional education (12.5%). Most of the escape rooms had a group-based physical design and little attention was given to provide a detailed description of the design considerations, such as the pathway type (linear, semi-linear, open). Conclusion: Escape rooms are applied in a wide range of medical education areas. In Medical Education, group-based on-site escape rooms with a focus on nursing, emergency medicine, pharmacy and interprofessional education dominates the implementation landscape. To further advance the field, stronger emphasis on making explicit the design considerations will advance the research and inform implementations.