This article discusses the results of fluid inclusions study in barite collected at the Jan Mayen vent field area (Troll Wall and Perle & Bruce) and Loki’s Castle vent field of the Mohns Ridge segment of the Arctic Mid-Ocean Ridge. Three mafic-hosted volcanogenic massive sulfide deposits were examined within the active vent fields that adequately correspond to geological settings of ultraslow-spreading ridges and PT-conditions. Hydrothermal sediments were investigated to determine the temperature and salinity of the fluids responsible for barite precipitation. The hydrothermal origin of the barite was confirmed by its morphology. Fluid inclusions are two-phase and homogenized into the liquid phase on heating at temperatures below 287ºC. The salt concentration in fluids trapped in inclusions is 2.6–4.4 wt.% NaCl eq. The crystallization temperatures varied from 276ºС to 119ºС and from 307ºС to 223ºС for the Jan Mayen and Loki’s Castle vent fields, respectively. The data obtained allowed us to confirm evidence of fluid phase separation in the hydrothermal systems and to expand our knowledge of the temperature and salinity of mineral fluids previously known from recent direct measurements during the cruises within the G.O. Sars research vessel. The fluid inclusions data obtained from barites emphasize the fluid features characteristic of volcanogenic massive sulfide deposits, the similarities and differences for the studied hydrothermal sites, and allow comparisons with similar products from other active hydrothermal systems.

A new approach to preparing a series of Co/Sm2O3 catalysts for hydrogen production by dry re-forming of methane (DRM) is developed. The catalysts precursors are synthesized by a simple method, including evaporation of aqueous solutions of cobalt and samarium nitrates, followed by a short-term calcination of the resulting material. The as-prepared and spent catalysts are characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), temperature-programmed reduction (H2-TPR), and thermogravimetric analysis (TGA). It is shown that the content of cobalt in the synthesized materials affects their phase composition and carbonization resistance in the DRM reaction. It is demonstrated that preheating under N2 affords catalysts providing stable hydrogen and CO yields of 94-98 % for at least 50 h at 900°C. These yields are among the highest ones currently available for DRM catalysts derived from Co-Sm complex oxides. It is found that reduction in the amount of cobalt in the catalyst and its preheating to an operating temperature of 900°C in a nitrogen flow con-tribute to preventing catalyst carbonization and metal particles sintering.

The microwave field is used for drying and disinfection of grain, during pre-sowing seed treat-ment. The use of a microwave field in these installations leads to an increase in their productivity and a decrease in the energy consumed by them. One of the principal problems of microwave field use for treatment of dense grain layers is to insure sufficient distribution uniformity of the field. In this article, waveguide design options have been discussed that serve to introduce microwave radiation into the grain layer. Mathematical simulation of the electromagnetic field distribution was performed with the use of CST Microwave Studio software in order to evaluate and compare horn-type, rectangular and semicircular waveguides. The data on the standing wave ratio and radiation efficiency for these types of waveguides have been reported. Specific features of the microwave electromagnetic field distribution and radiation power in the output of those wave-guides have been described. Results of mathematical simulations enabled to make out that sem-icircular waveguides with slot-type radiators are preferable for processing dense grain layers.

The paradigm of drug delivery via nano- and microcarriers is one of the leading ideas that enable overcoming the limitations of traditional chemotherapy. The trend toward more complex drug carriers capable of multifunctionality is observed in the literature. To date, prospects of stimuli-responsive systems to control the cargo release in the lesion nidus are widely accepted. Both endogenous and exogenous stimuli are employed for this purpose, however, endogenous pH is one of the most common triggers. Unfortunately, scientists face difficulties in the implementation of this idea since a range of biological barriers, drug bioavailability issues, and challenges in the synthesis of carriers with required properties have arisen. Here, we discuss fundamental strategies of pH-responsive drug delivery as well as limits in its application and reveal the main problems, weak sides, and reasons for poor clinical results. Also, we have made an attempt to formulate the profiles of "ideal" drug carrier in the frame of different strategies and considered recently published studies through the lens of these profiles. This approach enables the identification of current trends and promising vectors in the development of pH-responsive drug delivery systems, as well as challenges to be resolved in the next generation of carriers.

Reliable species identification is critical for detection and monitoring of biological invasions. In this study, we propose four sets of primers for efficient amplification of several loci, including the mitochondrial cytochrome oxidase-c (COI) subunit I gene which is a basis for DNA barcoding. This set of primers gives a shorter product which can be used in high-throughput sequencing systems for metabarcoding purposes. Another mitochondrial locus encoding the large ribosomal subunit (16S) may be useful to study the population structure and as an additional source of information in the metabarcoding of communities. We propose to use a set of primers for the nuclear locus of the small ribosomal subunit (18S) as a positive control and to verify the results of the barcoding. Our proposed sets of primers demonstrate a high amplification efficiency and a high specificity both for freshwater alien and indigenous fishes. The proposed research design makes it possible to carry out extremely cheap studies on the assessment of biological diversity using genetic analysis without expensive equipment, and with the technique for conducting laboratory work and processing of the results available to any researcher. The paper also presents original data on the genetic polymorphism of all mass alien fish species in the Volga-Kama region. High efficiency of DNA identification based on our primers is shown as compared to traditional monitoring of biological invasions.

Abstract: The objective of these studies was to determine the dependence of the distribution of the microwave field into a grain layer and the efficiency of energy transfer from the magnetron into the grain layer, via a waveguide, on the moisture content. The subject of the research was a semicircular waveguide with slot radiators that supply a microwave field to the grain surrounding the waveguide. The change in the directional diagram of the microwave field in the longitudinal direction of the waveguide was studied using CST Microwave Studio 2019 software. It was found that the change in the moisture content of the processed grain leads to a significant change in both the radiation and total efficiency values of the waveguide. For instance, the radiation efficiency of the waveguide decreases by 15.1% (from 68.729 dB to 58.294 dB) when the moisture content of the processed grain increases from 14% to 26%. The total radiation efficiency also decreases (from 11.27 dB to 21.7 dB). In this case, not only the value of the radiation efficiency but also the shape of its dependence on the magnetron radiation frequency change. Data were obtained on the change in the Q-factor for resonators in which grain layers are processed, depending on the variation in grain moisture content.

This paper develops the study of the effect of powerful ultrasound on the laser breakdown of liquids and a comparative study of the possibilities of acoustic and optical diagnostics of breakdown. The method of laser-induced breakdown spectroscopy (LIBS) for elemental analysis of liquids, along with high efficiency, continues to be less sensitive compared to traditional chemical methods. The paper develops a method of using additional ultrasound irradiation of the laser breakdown area in order to increase the efficiency of LIBS. Using the developed technique, spectral lines of chemical elements such as potassium, manganese, sodium, calcium, etc. were obtained for the first time depending on the frequency and power of ultrasound. It is shown that a sharp increase in the intensity of spectral lines of elements in water during laser breakdown is observed in the field of high-power ultrasound. It indicates an increase in the sensitivity of the combined method of ultrasonic LIBS. Along with the optical spectrum, the spectral and energy characteristics of acoustic emission were studied. An automated complex for hydrophysical and spectral studies is described, which was tested in the Sea of Japan during the voyage No. 81 of the research vessel RV "Professor Gagarinsky" in August 2022.

The mitochondrial network (MN) is a dynamic structure undergoing constant remodeling in the cell. It is assumed that the violation of MN may be associated with various pathologies, including Parkinson’s disease (PD). Using automatic image analysis and super-resolution microscopy, we have assessed the MN parameters in fibroblasts from patients with established hereditary PD mutations (associated with PINK1, LLRK2, α-synuclein, PINK1 and Parkin simultaneously proteins) under normal conditions and after hydrogen peroxide-induced stress. Fibroblasts with Pink1/Parkin mutation are the most different in morphology from fibroblasts obtained from conditionally healthy donors: MN is larger, contains longer mitochondria and accumulated individual mitochondria. In addition to MN, we evaluated other cellular parameters, such as: cytosolic and mitochondrial ROS production and mitochondrial membrane potential. It has been shown that mitochondria of fibroblasts with mutations in genes encoding PINK1, α-synuclein and Pink/Parkin tends to hyperpolarization and cytosolic ROS overproduction, while mitochondrial ROS production was higher only in fibroblasts with PINK1 and α-synuclein mutation.

The aim of our study was a comprehensive comparative assessment of the effect of consumption of 1 and 2% cholesterol as part of a standard diet with and without regular moderate physical activity on the main biomarkers of lipid and cholesterol metabolism, as well as the intestinal microbiota of male Wistar rats. The animals were randomly divided into 5 groups according to body weight and Open Field test results: Control (n=10), 1% Chol (n=10), 2% Chol (n=10), 1% Chol + RUN (n=10) and 2% Chol + RUN. The cholesterol was additionally added in the amount of 1g or 2g/100g, respectively, to the diet of animals. The rats of experimental groups 1% Chol + RUN and 2% Chol + RUN were subjected to regular (2 days a week) physical activity on a Treadmill. In rats of four experimental groups, when compared to the Control, a response of 39 indicators was revealed. The largest number of changes in biomarkers - 29 (statistically significant, p

The cryopreservation of gametes and embryos is an important element of biodiversity conservation. One species in need of conservation is the honey bee Apis mellifera L. Changing environmental factors, especially the anthropogenic factor, have led to a reduction in the numbers of this insect species. In this study, we provide an example of the creation of a biobank of honey bee drone sperm. For sperm cryopreservation, drones of the most common subspecies of honey bees common in Russia were selected. These were the dark forest bee, Apis mellifera mellifera from the Republic of Bashkortostan, with three subspecies (A. m. carnica, A. m. carpatica, and A. m. caucasica) from the southern regions of Russia, as well as two breeding stocks, the Far Eastern bee and Prioksky bee. For subspecies identification, morphometric and genetic methods were used. The subspecies of the studied samples were confirmed by the analysis of the tRNAleu-COII locus of mitochondrial DNA and nine microsatellite markers of nuclear DNA. It was shown that bees of the Prioksky breeding stock belong to the subspecies A. m. caucasica based on phylogenetic analysis, and the Far Eastern breeding stock is a stable hybrid, descending on the maternal line from the evolutionary lineage C or O. The results of the morphometric analysis are consistent with the results of the genetic analysis. For the cryopreservation of sperm, we used a honey diluent. As a result, the viability of frozen–thawed sperm decreased by 20.3% compared to fresh sperm, and overall motility decreased by 25-fold. The measurement of the sperm concentration in the spermatheca of artificially inseminated queens showed that it varied from 0.22 to 4.4 million/μL. Therefore, the use of honey in sperm cryopreservation has great potential.

Protein-DNA interactions are critical for the successful functioning of all natural systems. The key role in these interactions is played by processes of protein search for specific sites on DNA. Although it has been studied for many years, only recently microscopic aspects of these processes became more clear. In this work, we present a review on current theoretical understanding of the molecular mechanisms of the protein target search. A comprehensive discrete-state stochastic method to explain the dynamics of the protein search phenomena is introduced and explained. Our theoretical approach utilizes a first-passage analysis and it takes into account the most relevant physical-chemical processes. It is able to describe many fascinating features of the protein search, including unusually high effective association rates, high selectivity and specificity, and the robustness in the presence of crowders and sequence heterogeneity.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

Rapid emergence of evasive SARS-CoV-2 variants is an on-going challenge for COVID-19 vaccinology. Traditional virus neutralization tests provide detailed datasets of neutralization titers against the viral variants. Such datasets are difficult to interpret and do not immediately inform on the sufficiency of the breadth of antibody response. Some of these issues could be tackled using the antigenic cartography approach. In this study, we created antigenic maps using neutralization titers of sera from donors who received Sputnik V booster vaccine after primary Sputnik V vaccination and compared them with the antigenic maps based on serum neutralization titers of Comirnaty-boosted donors. Traditional analysis of neutralization titers against WT, Alpha, Beta, Delta, Omicron BA.1 and BA.4/BA.5 showed a significant booster humoral response after both homologous (Sputnik V) and heterologous (Comirnaty) revaccinations against all the studied viral variants. However, despite this, a more in-depth analysis using antigenic cartography revealed that Omicron variants remain antigenically distant from WT, which is indicative of the formation of insufficient levels of cross-neutralizing antibodies. The implications of these findings may be significant when developing a new vaccine regimen.

Various iron oxides have been proven to be promising anode materials for metal-ion batteries due to their natural abundance, high theoretical capacity, ease of preparation, and environmental friendliness. However, the synthesis of iron oxide-based composites requires complex approaches, especially when it comes to composites with intrinsically conductive polymers. In this work we propose a one-step microplasma synthesis of a polyaniline-coated urchin-like FeOOH nanoparticles (FeOOH/PANI) for application as anode in lithium-ion batteries. The material shows excellent electrochemical characteristics, providing initial capacity of ca. 1600 mA∙h∙g−1 at 0.05 A∙g−1 and 900 mA∙g−1 at 1.2 A∙g−1. Further cycling lead to capacity decrease to 150 mA∙h∙g−1 by the 60th cycles, followed by a recovery that maintained the capacity at 767 mA∙h∙g−1 after 2000 cycles at 1.2 A∙g−1 and restored full initial capacity of 1600 mA∙h∙g−1 at low current density of 0.05 A∙g−1. Electrochemical milling of the material caused such interesting behavior of the material, and we confirmed this phenomenon by a combination of physico-chemical and electrochemical techniques. The anodes also exhibit high performance in a full cell with NMC532. NMC532//FeOOH/PANI full cell provided energy density of 224 Wh∙kg−1 which is comparable to the reference cell with graphite anode (264 Wh∙kg−1).

The transcriptional coactivators YAP (Yes-associated protein) and TAZ (transcriptional coactivator with PDZ-binding motif) are the main downstream effectors of the evolutionary conserved Hippo signaling pathway. YAP/TAZ is implicated in the transcriptional regulation of target genes that are involved in a wide range of key biological processes affecting tissue homeostasis and play dual roles in the aging process depending on cellular and tissue context. The aim of the present study was to investigate whether pharmacological inhibitors of Yap/Taz may increase the lifespan of Drosophila melanogaster. qRT-PCR was performed to measure the changes in the expression level of Yki (Yorkie, the Drosophila homolog of YAP/TAZ) target genes. We have revealed a lifespan increasing effect of YAP/TAZ inhibitors that was mostly associated with decreased expression level of wg and E2f1 genes. However further analysis is required to understand how YAP/TAZ pathway is linked with aging.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

For the KdV-Burgers equations on cylindrical and spherical waves the development of a regular profile starting from an equilibrium under a periodic perturbation at the boundary is studied. The equations describe a medium which is both dissipative and dispersive. Symmetries, invariant solutions and conservation laws are investigated. For an appropriate combination of dispersion and dissipation the asymptotic profile looks like a periodical chain of shock fronts with a decreasing amplitude (sawtooth waves). The development of such a profile is preceded by a head shock of a constant height and equal velocity which depends on spatial dimension as well as on integral characteristics of boundary condition; an explicit asymptotic for this head shock and a median of the oscillating part is found.

This review is focused on synephrine, the principal phytochemical found in bitter orange and other medicinal plants, and widely used as a dietary supplement for weight loss/body fat reduction. We examine different aspects of synephrine biology, delving into its established and potential molecular targets, as well as its mechanisms of action. We present an overview of the origin, chemical composition, receptors, and pharmacological properties of synephrine, including its anti-inflammatory and anti-cancer activity in various in vitro and animal models. Additionally, we conduct a comparative analysis of the molecular targets and effects of synephrine with those of its metabolite, selective glucocorticoid receptor agonist (SEGRA) Compound A (CpdA), which shares a similar chemical structure with synephrine. SEGRA, including CpdA, have been extensively studied as glucocorticoid receptor activators that have a better benefit/risk profile than glucocorticoids due to the reduced adverse effects. We discuss the potential of synephrine usage as a template for the synthesis of new generation of non-steroidal SEGRA. The review also provides insights into the safe pharmacological profile of synephrine.

A closed chain of oscillators can be considered as a model of ring-shaped ecosystems, such as atolls or coastal zones of inland reservoirs. As an oscillator model, we use the logistic map that often referred to as an archetypical example of how complex dynamics can arise from very simple nonlinear equations. We investigate the influence of the model parameters both on the nature of oscillations in the oscillator ring and on the spatial structures that arise in this case. Namely, we demonstrate a variety of emerging spatial structures depending on the initial conditions.

The results of experimental studies of ohmic conductivity degradation in the ensembles of nanostructured anatase bridges under long-term effect of direct current are presented. Stochastic sets of interelectrode partially conducting bridges consisting of close-packed anatase nanoparticles were formed by the seeding particles from drying aqueous suspensions on the surfaces of silica substrates with interdigital platinum electrodes. Multiple-run experiments at room temperature have shown that ohmic conductivity degradation in these systems is irreversible. It is presumably due to accumulated capture of conduction electrons by deep traps in anatase nanoparticles. The scaling analysis of voltage drops across the samples at the final stage of degradation gives a critical exponent for ohmic conductivity as 1.597. This value satisfactorily agrees with the reported model data for percolation systems. At an early stage of degradation, the spectral density of conduction current fluctuations wihin the frequency range of 0.01 Hz - 1 Hz decreases approximately as , while near the percolation threshold the decrease trend changes to . This transition is interpreted in terms of an increasing contribution of blockages and subsequent avalanche-like breakdowns of part of the local conduction channels in the bridges into electron transport near the percolation threshold.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

The terpolymers of N-vinylpyrrolidone (VP) with acrylic acid and triethylene glycol methacrylate were synthesized with more than 90% yield by radical copolymerization in ethanol from monomeric mixtures of different composition (98 : 2 : 2, 95 : 5: 2 and 98 : 2: 5). Their physical and chemical characteristics such as monomer composition, absolute molecular masses and hy-drodynamic radii in aqueous media at different temperature were determined. The temperature effect on the behavior of terpolymers in water and aqueous saline buffer solution with pH 7.4 has been studied and the ability of a copolymer enriched with dimethacrylates units was discovered to respond to a temperature change in these media. On the basis of terpolymers and linear polyvi-nylpyrrolidone (PVP), polymer compositions of hydrophobic dye methyl pheophorbide a, MPP, that is fluorescent in the red region of the spectrum, were obtained; the sizes of the polymer nanostructures of MPP in water were determined. The structures based on terpolymers were demonstrated to be more stable than MPP-PVP ones. It was carried out the quantum-chemical modelling of the possible structures of MPP-copolymer that formed as a result of intermolecular interaction between MPP and terpolymer’s chains; the possibility of the formation of hydrogen bonds between the donors of the electrons of terpolymer units and the proton donors of the MPP molecule was shown. Using the MTT test, it was established that copolymers of various compositions are low toxic for non-tumor Vero cells and HeLa tumor cells. It was shown that the cytotoxicity of polymer particles loaded with MPP for FetMSC and HeLa cells increased. Using fluorescence microscopy, the accumulation and distribution of polymer particles in non-tumor (FetMSC) and tumor (HeLa) cells was studied and an increase in the accumulation of MPP with both types of particles was shown.

We studied surface enhanced Raman spectra of amino acids D-alanine and DL-serine and their mixture on silver nanoisland films (SNF), immersed in phosphate buffer saline solution at millimolar amino acid concentrations. It is shown that the spectra from the amino acid solutions differ from the reference spectra for microcrystallites due to electrostatic orientation of amino acid zwitterions by the metal nanoisland film. Moreover, non-additive peaks are observed in the spectrum of the mixture of amino acids adsorbed on SNF, which means that intermolecular interactions between adsorbed amino acids are very significant. The results indicate the need for a thorough analysis of the Raman spectra from amino acid solutions in the presence of a nanostructured metal surface, and may also be of interest for studying molecular properties and intermolecular interactions.

Osteoconductive granulated biopolymers (OGB) are used to restore the lost volume of the jaw bone. OGB is employed as a loose fraction and exhibits physical traits common to bulk mixtures. By removing air bubbles and industrial dust from the OGB fraction through special processing, more accessible spaces are left over for the adsorption of bone growth factors. The recipient site's biological environment alters the OGB fraction's physical characteristics. This is the cause of the OGB fraction's volume changing uncontrollably during the first three weeks following surgery. Predictive indicators for describing the physical processes of osteoconduction include the compaction coefficient and adsorption capacity. Taking into account the prognostic indicators of the dynamics of changes in the physical properties of the OGB fraction in the postoperative period, 3D planning of the bioengineered structure should be done. The OGB fraction's adsorption and drainage properties are optimized by raising the purity of OGB production and preparing the biopolymer for clinical studies.

Spontaneous tumours in higher plants can develop depending on plant genotype without any pathogen invasion. Spontaneous tumour formation on the taproots is consistently observed in certain inbred lines of radish (Raphanus sativus var. radicula Pers.). In this work, we have sequenced the genomes of two closely related radish inbred lines that differ in their ability to spontaneously form tumours. We have identified numerous single nucleotide variants (amino acid substitutions, insertions or deletions) that are likely to be associated with the spontaneous tumour formation. Furthermore, we performed the identification of CLE and WOX genes the genomic sequences of the radish inbred lines and, as a result, identified two unique radish CLE genes which probably encode proteins with multiple CLE domains. The results obtained provide a basis for investigating the mechanisms of plant tumour formation and also for future genetic and genomic studies of radish.

With the intensive development of data transmitting and processing devices of the terahertz (THz) frequency range, an important part of which are integrated plasmonic components and communication lines, it becomes necessary to measure correctly the optical constants of their conductive surfaces. In the paper we describe a reliable method for determining the effective permittivity εm of a metal surface from the measured characteristics (refractive and absorption indices) of THz surface plasmon polaritons (SPPs). The novelty of the method is the conduction of measurements on a metal surface with a dielectric layer of subwavelength thickness, suppressing the radiative losses of SPPs, which are not taken into account by the SPP dispersion equation. The method was tested on a number of flat "gold sputtering - zinc sulfide layer - air" structures with the use of the THz radiation (λ0 = 141 μm) of the Novosibirsk free electron laser (NovoFEL). The SPP characteristics were determined from interferograms measured with a plasmon Michelson interferometer. It was found that the method allowed a significant increase in the accuracy of εm in comparison with measurements on the same metal surface without a dielectric layer.

: In this article, the authors propose an algorithmic approach to building a model of the dynamics of economic and, in particular, innovation processes. The approach under consideration is based on a complex algorithm that includes (1) decomposition of the time series into components using singular spectrum analysis; (2) recognition of the optimal component model based on fuzzy rules, and (3) creation of statistical models of individual components with their combination. It is shown that this approach corresponds to the high uncertainty characteristic of the tasks of the dynamics of innovation processes. The proposed algorithm makes it possible to create effective models that can be used both for analysis and for predicting the future states of the processes under study. The advantage of this algorithm is the possibility to expand the base of rules and components used for modeling. This is an important condition for improving the algorithm and its applicability for solving a wide range of problems.

Effective therapeutics for Alzheimer's disease (AD) are in great demand worldwide. In our previous work, we responded to this need by synthesizing novel drug candidates consisting of 4-amino-2,3-polymethylenequinolines conjugated with butylated hydroxytoluene via fixed-length alkylimine or alkylamine linkers (spacers) and studying their bioactivities pertaining to AD treatment. Here, we report significant extensions of these studies, including the use of variable-length spacers and more detailed biological characterizations. Conjugates were potent inhibitors of acetylcholinesterase (AChE, minimum IC50 15.1±0.2 nM) and butyrylcholinesterase (BChE, minimum IC50 5.96±0.58 nM), with weak inhibition of off-target carboxylesterase. Conjugates with alkylamine spacers were more effective cholinesterase inhibitors than alkylimine analogs. Optimal inhibition for AChE was exhibited by cyclohexaquinoline and for BChE by cycloheptaquinoline. Increasing spacer length elevated potency against both cholinesterases. Structure-activity relationships agreed with docking results. Mixed-type reversible AChE inhibition, dual docking to catalytic and peripheral anionic sites, and propidium iodide displacement suggested the potential of hybrids to block AChE-induced β-amyloid (Aβ) aggregation. Hybrids also exhibited inhibition of Aβ self-aggregation in the thioflavin test; those with a hexaquinoline ring and C8 spacer were the most active. Conjugates demonstrated high antioxidant activity in ABTS and FRAP assays as well as inhibition of luminol chemiluminescence and lipid peroxidation in mouse brain homogenates. Quantum-chemical calculations explained antioxidant results. Computed ADMET profiles indicated favorable blood-brain barrier permeability suggesting CNS activity potential. Thus, the conjugates could be considered promising multifunctional agents for potential treatment of AD.

The quest for surgical advancements regarding the enhancement of the submental and cervicofacial regions has witnessed a remarkable upsurge in recent years. Informed patients are actively seeking sophisticated plastic surgery techniques to achieve comprehensive rejuvenation in these specific areas. Our clinical practice encounters an annual influx of approximately 400 patients, with 20% of them aged over 60, seeking facial rejuvenation encompassing the details of lower third of the face and neck. Common concerns expressed by these patients include sagging of the jawline, the emergence of deep perioral wrinkles, and the formation of "marionette lines" within the lower third of the face. Furthermore, the manifestation of age-related signs, including neck laxity, submental adipose accumulation, "witch's chin" deformity, and weakened platysma musculature, is frequently encountered within this intricate anatomical domain. This review aims to summarize the recent technical improvements, historical evolution, indications, postoperative care and challenges for facial rejuvenation of the lower third of the face and neck. Lastly, the application of minimally invasive procedures as part of a comprehensive approach to an aging face will also be discussed.

A method for studying properties of the earth's surface tremor, measured by means of GPS, is proposed. Four characteristics of tremor are considered: the entropy of the distribution of wavelet coefficients, the Donoho-Johnston wavelet index, and two estimates of the spectral slope. The anomalous areas of tremor are determined by estimating the probability densities of extreme values of the studied properties. The criteria for abnormal tremor behavior are based on the proximity to, or the difference between, tremor properties and white noise. The greatest deviation from the properties of white noise is characterized by entropy minima and spectral slope and DJ index maxima. This behavior of the tremor is called "active". The "passive" tremor behavior is characterized by the maximum proximity to the properties of white noise. The principal components approach provides weighted averaged density maps of these 2 variants of extreme distributions of parameters in a sliding time window of 3 years are considered. Singular points are the points of maximum average densities. The method is applied to the analysis of daily time series from a GPS network in the West USA in 2009-2022. It turned out that singular points of tremor form well-defined clusters.

A method for studying properties of the earth's surface tremor, measured by means of GPS, is proposed. Four characteristics of tremor are considered: the entropy of the distribution of wavelet coefficients, the Donoho-Johnston wavelet index, and two estimates of the spectral slope. The anomalous areas of tremor are determined by estimating the probability densities of extreme values of the studied properties. The criteria for abnormal tremor behavior are based on the proximity to, or the difference between, tremor properties and white noise. The greatest deviation from the properties of white noise is characterized by entropy minima and spectral slope and DJ index maxima. This behavior of the tremor is called "active". The "passive" tremor behavior is characterized by the maximum proximity to the properties of white noise. The principal components approach provides weighted averaged density maps of these 2 variants of extreme distributions of parameters in a sliding time window of 3 years are considered. Singular points are the points of maximum average densities. The method is applied to the analysis of daily time series from a GPS network in the West USA in 2009-2022. It turned out that singular points of tremor form well-defined clusters.

The correlations of seismic noise, recorded during 1997-2022 at 229 stations around the world are investigated. The property of waveforms, known as the Donoho-Johnston threshold, is analyzed, which separates the absolute values of the orthogonal wavelet coefficients into "small" and "large". Network of 50 reference points is considered. For each reference point, a time series with a time step of 1 day is calculated as the median of the values of the DJ index from the 5 nearest stations. For each reference point, the correlations between the values of the DJ index at other reference points are calculated in a sliding time window of 365 days. Average values of the DJ index decrease, which is interpreted as indicators of global seismic hazard increasing. The maximum distances between reference points with strong correlations show an explosive increase after 2011. Bursts in the mean coherences between the length of day (LOD) and the values of the DJ index at the reference points precede the release of seismic energy with a delay of about 530 days. High amplitude of the DJ index response to LOD for the times 2020-2022 was identified, which may forecast a strong earthquake in the second half of 2023.

A set of programs for the numerical simulation of the diffusion decomposition processes was developed by using simulation methods, kinetic and particle method. The complex has been validated on the model system Ni-Al by the growth of -phase separations. The results on the evolution of the distribution function and other characteristics of the ensemble, which in the zero volume fraction approximation are asymptotically in good agreement with the theory and the experiment, have been obtained. The peculiarity of the created program complex is the possibility of its adaptation to the description of the decomposition of multicomponent multiphase systems. Fig. 6, list of references - 19 titles.

Capabilities of hovering unmanned aerial vehicles (UAVs) in low-altitude sensing of atmospheric turbulence with high spatial resolution are studied experimentally. The experiment was carried out at the Basic Experimental Observatory of the V.E. Zuev Institute of Atmospheric Optics SB RAS. UAV findings are compared with objective data on the state of the atmosphere that were measured by acoustic anemometers installed at weather towers at altitudes of 4, 10, and 27 m. Profiles of atmospheric turbulence were recorded with three UAVs hovering at the same heights at a distance of 5 m from the anemometers. The behavior of the longitudinal and lateral wind velocity components is studied in the frequency band 0-10 Hz before and after one-minute smoothing, which reveals long turbulent wind gusts. The discrepancy between the UAV and anemometer data is analyzed. It is found that after smoothing, the discrepancy does not exceed 0.5 m/s in 95% cases. This value meets the requirements of the World Meteorological Organization for some applications in wind velocity measurements. The spectral and correlation analysis of the UAV and anemometer measurements is carried out. The profiles of the longitudinal and lateral scales of turbulence are examined based on the UAV data and are found to be in agreement with the anemometer data to a good accuracy.

The capabilities of a quadcopter in the hover mode for low-altitude sensing of atmospheric turbulence with high spatial resolution in urban areas characterized by complex orography are investigated. The studies were carried out in different seasons (winter, spring, summer, and fall), and the quadcopter hovered in the immediate vicinity of ultrasonic weather stations. The DJI Phantom 4 Pro quadcopter and AMK-03 ultrasonic weather stations installed in different places of the studied territory were used in the experiment. The smoothing procedure was used to main regularities in the behavior of the longitudinal and lateral spectra of turbulence in the inertial and energy production ranges. The longitudinal and lateral turbulence scales were estimated by the least-square fit method with the von Karman model as a regression curve. It is shown that the turbulence spectra obtained with DJI Phantom 4 Pro and AMK-03 generally coincide with minor differences observed in the high-frequency region of the spectrum. In the inertial range, the behavior of the turbulence spectra shows that they obey the Kolmogorov-Obukhov “5/3” law. In the energy production range, the longitudinal and lateral turbulence scales and their ratio measured by DJI Phantom 4 Pro and AMK-03 agree to a good accuracy. Discrepancies in the data obtained with the quadcopter and the ultrasonic weather stations at the territory with complex orography are explained by the partial correlation of the wind velocity series at different measurement points and the influence of the inhomogeneous surface.

Based on the theory of turbulence, equations are derived for estimations of turbulent fluctuations of the longitudinal and transverse components of the wind velocity during ideal hovering of a quadcopter in a turbulent atmosphere. We present the results of experiments which were carried out on the territory of the Geophysical Observatory of Institute of Monitoring of Climatic and Ecological Systems, Siberian Branch, Russian Academy of Sciences, located in Tomsk Akademgorodok on the territory with complex orography, in a parkland zone with buildings of research institutes and motorways. Time series of turbulent fluctuations of the longitudinal and transverse components of wind velocity fluctuations were received with the use of an automated weather station, and time series of estimates of these components, from data of a DJI Phantom 4 Pro quadcopter during hovering. According to the automated weather station data, anisotropy was observed in one experiment during measurements in the atmosphere, but this phenomenon was not observed in the other experiment: the fluctuation spectra of all components of wind speed fluctuations coincide. The spectra of fluctuations of the longitudinal and transverse wind velocity components based on the automated weather station data and UAV telemetry are presented. The fluctuation spectra of these components for the automated weather station data and quadcopter generally coincide. The behavior of the spectra coincides with the spectrum which corresponds to Kolmogorov–Obukhov “–5/3” law within the inertial range. The turbulent spectra of the wind velocity fluctuations obtained with the use of the automatic weather station and with the unmanned aerial vehicle differ in the high-frequency spectral region.

In plants, water flows are the major driving force behind the growth and play a crucial role in the life cycle. To study hydrodynamics, methods based on tracking small particles inside water flows occupy a special place. Due to these tools, it is possible to get information about the dynamics of the spatial distribution of the fluxes characteristics. In this paper, using contrast-enhanced MRI, we have shown that gadolinium chelate, used as an MRI contrast agent, marks the structural characteristics of xylem bundles of maize stem nodes and internodes. Supplementing MRI data, a high-precision visualization of xylem vessels by laser scanning microscopy was used to reveal structural and dimensional characteristics of the stem vascular system. In addition, we proposed the concept of using the prototype "Y-type xylem vascular bundles" as a model of the elementary connection of vessels within the vascular system. A Reynolds number can match the microchannel model with the real xylem vessels.

Three-layer structures based on various multi-component films of III–V semiconductors heavily doped with Fe were grown by pulsed laser sputtering of InSb, GaSb, InAs, GaAs and Fe solid targets. The structures comprising InAsSb:Fe, InGaSb:Fe and InSb:Fe layers with Fe concentrations up to 24 at. % separated by GaAs spacers were deposited on (001) i-GaAs substrates at 200ºC. Transmission electron microscopy showed that the structures have a rather high crystalline quality and do not contain secondary-phase inclusions. X-ray photoelectron spectroscopy investigations revealed significant diffusion of Ga atoms from the GaAs regions into the InAsSb:Fe layers, which has led to the formation of an InGaAsSb:Fe compound with a Ga content up to 20 at. %. It has been found that the ferromagnetic properties of the InAsSb:Fe magnetic semiconductor improve with increasing Sb:As ratio. It has been concluded that the indirect ferromagnetic exchange interaction between Fe atoms occurs predominantly via Sb atoms.

The fractal dimension of geomagnetic variations at the Baigazan magnetic station at Russian Altay for 2011-2013 was calculated using the Higuchi method. The daily variation of Higuchi Fractal Dimension (HFD) for the D,H,Z-components of the geomagnetic field has been investigated, its contribution to the variability of HFD is from 30 to 40 percent of the total variance. A correlation analysis of the fractal dimension of the variations of the D,H,Z-components with Auroral Electrojet (AE) index and solar wind characteristics was carried out. A negative correlations with logarithms of AE-index, interplanetary magnetic field (IMF) strength and solar wind velocity were found. About 25 percent of the fractal dimension variance is controlled by the variability of these characteristics. Pair and partial correlation coefficients for these parameters were calculated for every month of 2011-2013.

Treatment of various diseases, in particular cancer, usually needs targeting biologically active molecules at a selected subcellular compartment. We modified our previously developed modular nanotransporters (MNTs) for targeting mitochondria. The new MNTs are capable of binding to the protein predominantly localized on the outer mitochondrial membrane, Keap1. These MNTs possessing antiKeap1 monobody co-localize with mitochondria upon addition to the cells. They efficiently interact with Keap1 both in solution and within living cells. A conjugate of the MNT with a photosensitizer, chlorin e6, demonstrates significantly higher photocytotoxicity than chlorine e6 alone. We assume that MNTs of this kind can improve efficiency of therapeutic photosensitizers and radionuclides emitting short-range particles.

Activated platelets are involved in blood coagulation by exposing phosphatidylserine (PS), which serves as a substrate for assembling coagulation complexes. Platelets accelerate fibrin formation and thrombin generation, two final reactions of the coagulation cascade. We investigated the effects of antiplatelet drugs on platelet impact in these reactions and platelet ability to expose PS. Washed human platelets were incubated with acetylsalicylic acid (ASA), ticagrelor, ASA in combination with ticagrelor, ruciromab (glycoprotein IIb-IIIa antagonist) or prostaglandin E1 (PGE1). Platelets were not activated or activated by collagen, sedimented in multiwell plates and plasma was added after supernatant removal. Fibrin formation (clotting) was monitored in a recalcification assay by light absorbance and thrombin generation in a fluorogenic test. PS exposure was assessed by annexin V staining using flow cytometry. Ticagrelor (alone and in combination with ASA), ruciromab and PGE1, but not ASA prolonged the lag phase and decreased the maximum rate of plasma clotting, and decreased the peak and maximum rate of thrombin generation. Inhibition was observed when platelets were not treated with exogenous agonists (activation by endogenous thrombin) and pretreated with collagen. Ticagrelor (alone and in combination with ASA), ruciromab and PGE1, but not ASA decreased PS exposure on washed platelets activated by thrombin and by thrombin + collagen. PS exposure on activated platelets in whole blood was lower in patients with acute coronary syndrome receiving ticagrelor + ASA in comparison with donors free of medications. These results indicate that antiplatelet drugs are able to suppress platelet coagulation activity not only in vitro but also after administration to patients.

In addition to nucleic acids, various viral proteins are involved in the assembly of virion. If it is possible to create a biologically active agent that leads to the degradation of one of the key proteins for virus assembly and/or destroys the viral factory, then this agent will effectively cope with virus replication. One of these key proteins for the SARS-CoV-2 virus is the nucleocapsid protein (N-protein). As such a bioactive agent, we offer a modular nanotransporter (MNT) developed by us, which, in addition to an antibody mimetic to the N-protein, contains an amino acid sequence for the attraction of the Keap1 E3 ubiquitin ligase. This should lead to the subsequent degradation of the N-protein. We have shown that functional properties of modules within the MNT permit its internalization into target cells, endosome escape into the cytosol, and binding to the N-protein. Using flow cytometry and Western blot, it was demonstrated that significant degradation of N-protein is observed when A549 and A431 cells transformed with N-protein are incubated with the developed MNTs. The proposed MNTs open up a new approach for the treatment of viral diseases.

Familial dysbetalipoproteinemia (FD) is a highly atherogenic genetically-based lipid disorder with the underestimated actual prevalence. In the recent years, several biochemical algorithms have been developed to diagnose FD using available laboratory tests. However, there is not enough data on their use in real-world clinical implementation. We studied the applicability of the most accessible biochemical algorithms to diagnose FD in clinical practice. We also investi-gated the prevalence of FD in one of the European regions of Russia based on a population sample. In this study there was detected a high prevalence of FD: 1 in 151. We demonstrated that the diagnostic algorithms of FD including a diagnostic apoB levels require correction, taking into account the characteristics of the distribution of apoB levels in the population. At the same time a triglycerides cutoff ≥1.5 mmol/L may be a useful tool in identifying subjects with FD. We also analyzed the presence and pathogenicity of APOE variants associated with the autosomal dominant FD in a large research sample.

This study evaluates audiogenic epilepsy in Krushinsky-Molodkina rats using a wireless EEG system to overcome the limitations of traditional methods that restrict animal movement. Nine male KM rats, prone to audiogenic seizures, were implanted with electrodes in areas critical for seizure activity (inferior colliculus, ventrolateral periaqueductal gray, dorsal area of the secondary auditory cortex, and motor cortex). This setup allowed for the observation of seizures without movement restriction. Results showed that targeted neural intervention via electrode implantation reduced the intensity of convulsive seizures in half of the subjects, suggesting a potential therapeutic approach. The severity of seizures was influenced by the pre-phonostimulation EEG background activity in specific brain regions, identifying them as key in the genesis and generalization of seizures. Observations of dual generalized seizure waves and induced hyperkinesis challenge conventional epilepsy models and suggest new directions for research and therapy development.

Mitochondrial pyruvate dehydrogenase complex (PDHC) is essential for the brain glucose and neurotransmitter metabolism, dysregulated in many pathologies. Using specific inhibitors of PDHC in vivo, we determine biochemical and physiological responses to PDHC dysfunction. Dose dependence of the responses to membrane-permeable dimethyl acetylphosphonate (Ac-PMe2) is non-monotonous. Primary decreases in glutathione and its redox potential, methionine and ethanolamine are alleviated with increasing PDHC inhibition, the alleviation accompanied by physiological changes. Comparison of 39 brain biochemical parameters after administration of four phosphinate and phosphonate analogs of pyruvate at a fixed dose of 0.1 mmol/kg reveals no primary, but the secondary changes, such as activation of 2-oxoglutarate dehydrogenase complex (OGDHC) and decreased levels of glutamate, isoleucine and leucine. The accompanying decreases in RMSSD of ECG and freezing time are most pronounced after administration of me-thyl acetylphosphinate and dimethyl acetylphosphonate. The levels of PDHA1 expression and phosphorylation, sirtuin 3 and total protein acetylation are not significantly changed by the PDHC inhibitors that affect the brain protein succinylation and glutarylation. Thus, decreased production of the tricarboxylic acid cycle substrate acetyl-CoA by inhibited PDHC is compen-sated by increased degradation of amino acids through the cycle with activated OGDHC, increas-ing total protein succinylation and decreasing anxiety indicators.

The global development of bioeconomy is impossible without technologies for comprehensive processing of plant renewable resources. The use of proven pretreatment technologies raises the possibility of industrial implementation of enzymatic conversion of polysaccharides from lignocellulose considering the process complexity. For instance, a well-tuned kraft pulping produces a substrate easily degraded by cellulases and hemicelulases. Enzymatic hydrolysis of bleached hardwood kraft pulp was carried out using an enzyme complex of endoglucanases, cellobiohydrolases, b-glucosidases and xylanases produced by recombinant strains of Penicillium verruculosum at a 10 FPU/g mixture rate and a 10 % substrate concentration. As a result of biocatalysis the following products are obtained: sugar solution, mainly glucose, xylobiose, xylose, as well as other minor reducing sugars; modified complex based on cellulose and xylan. The composition of biomodified kraft pulp was determined involving the use of HPLC. The method for determining the degree of crystallinity on an X-ray diffractometer was used to characterize the properties. The article shows the possibility of producing modified cellulose cryogels by amorphization with concentrated 85 % H3PO4 followed by precipitation with water and supercritical drying. Analysis of the enzymatic hydrolysate composition reveals the predominance of glucose (55...67 %) in reducing sugars with a maximum content of up to 6 % in the solution after 72 hours. The properties and structure of modified kraft pulp were shown to change during biocatalysis, in particular, the degree of crystallinity increased by 5 % after 3 hours of enzymatic hydrolysis. We obtained cryogels based on the initial and biomodified kraft pulp with conversion rates of 35, 50 and 70 %. The properties of these cryogels are not inferior to those based on industrial microcrystalline cellulose, as confirmed by the specific surface area, degree of swelling, porosity and SEM images. Thus, kraft pulp enzymatic hydrolysis offers prospects not only for producing sugar-rich hydrolysates for microbiological synthesis, but also for producing cellulose powders and cryogels with specified properties.

Flax seed is one of the richest plant sources of linolenic acid (LIN) and also contains unsaturated linoleic acid (LIO) and oleic acid (OLE). Stearoyl-ACP desaturases (SAD) and fatty acid desaturases (FAD) play a key role in the synthesis of flax fatty acids (FA). We sequenced flax seed transcriptomes at the 3, 7, 14, 21, and 28 day after flowering (DAF) for ten flax varieties with different oil FA compositions grown under three temperature/watering conditions. Expression levels of 25 genes of SAD, FAD2, and FAD3 families were evaluated. FAD3b, FAD3a, FAD2b-2, SAD3-1, SAD2-1, SAD2-2, SAD3-2, FAD2a-1, and FAD2a-2 had the highest expression levels, which changed significantly during seed development. These genes probably play a key role in the FA synthesis in flax seeds. High temperature and insufficient watering shifted the maximum expression levels of the FAD and SAD genes to earlier development stages, while the opposite trend was observed for low temperature and excessive watering. Differences in FAD and SAD expression profiles under different growth conditions could contribute to the FA composition of linseed oil. Stop codons in the FAD3a gene, resulting in reduced LIN content, decreased the level of the FAD3a transcript. Some difference in reaching the maximum expression level during seed development was observed between 1) SAD3-1, SAD3-2, and FAD2b-2 and 2) SAD2-1, SAD2-2, FAD2a-1, FAD2a-2, FAD3a, and FAD3b. These groups possibly contribute somewhat differently to the synthesis of FA at different development stages.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

S100 is a family of over 20 structurally homologous, but functionally diverse regulatory (calcium/zinc)-binding proteins of vertebrates. The involvement of S100 proteins in numerous vital (patho)physiological processes is mediated by their interaction with various (intra/extra)cellular protein partners, including cell surface receptors. Furthermore, recent studies revealed the ability of specific S100 proteins to affect cell signaling via direct interaction with cytokines. Previously, we have revealed binding of ca. 71% of the four-helical cytokines by S100P protein due to the presence in its molecule of a cytokine-binding site, which overlaps with the binding site for S100P receptor. Here we show that another S100 protein, S100A6 (pairwise sequence identity with S100P of 35%), specifically binds numerous four-helical cytokines. We have studied affinity of recombinant forms of 35 human four-helical cytokines covering all structural families of this fold to Ca2+-loaded recombinant human S100A6, using surface plasmon resonance spectroscopy. S100A6 recognizes 26 of the cytokines from all families of this fold with the equilibrium dissociation constants ranging from 0.3 nM to 12 µM. Overall, S100A6 interacts with ca. 73% of the four-helical cytokines studied to date with selectivity equivalent to that for S100P protein, with the differences limited to binding of Interleukin-2 and Oncostatin-M. The molecular docking study evidences presence in S100A6 molecule of a cytokine-binding site, analogous to that found in S100P. The findings argue the presence in some of the promiscuous members of S100 family of a site specific to a wide range of the four-helical cytokines. This unique feature of the S100 proteins potentially allows them to serve as universal inhibitors of signaling of the four-helical cytokines, which could be of value for reduction of severity of the disorders accompanied by excessive release of the cytokines.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

The article shows that active RC- and RLC- filters based on the simplest wideband SiGe transistor stages are quite promising for RF and microwave frequency ranges. The results of computer simulation of the RC- and RLC-filters proposed by the authors of this article, which are oriented for use in communication and telecommunications devices, incl. with tunable and adaptive parameters.

Ferroptosis is a unique variety of non-apoptotic cell death, driven by massive lipid oxidation in an iron-dependent manner. Since Ferroptosis was introduced as a concept in 2012, it was shown it's essential role in the pathogenesis in neurodegenerative diseases and an important role in therapy-resistant cancer cells. Thus, a detailed molecular understanding of both canonical and alternative ferroptosis pathways are required. There is a set of widely used chemical agents to modulate ferroptosis using different pathway targets: Erastin blocks cystine-glutamate antiporter, system xc-; ML210 directly inactivate GPX4; L-buthionine sulfoximine (BSO) inhibits γ-glutamylcysteine synthetase, an essential enzyme for glutathione synthesis de novo. Most studies were focused on lipidomic profiling of model systems undergoing death in a ferroptotic modality.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Chronobiotics is a group of drugs utilized to modify circadian rhythms targeting clock-associated molecular mechanisms. The circadian clock is known as a controller of numerous processes standing behind aging. Hypothesis: KL001 and KS15 targeting CRY, affect lifespan, locomotor activity and circadian rhythm of Drosophila melanogaster. We observed a slight (2%, p<0.001) geroprotective effect on median lifespan (5 µM solution of KL001 in 0.1% DMSO) and a 14% increase in maximum lifespan in the same group. KS15 10 µM solution extended males’ median lifespan by 8% (p <0.05). The statistically significant positive effects of KL001 and KS15 on lifespan were not observed in female flies. KL001 5 µM solution improved locomotor activity in young male imagos (p<0.05) and elevated morning activity peak in aged imagos and modified robustness of circadian rhythms, leaving the period intact. KS15 10 µM solution decreased the locomotor activity in constant darkness and minimized the number of rhythmic flies. KL001 5 µM solution improved by 9% the mean starvation resistance in male flies (p<0.01), while median resistance was elevated by 50% (p<0.0001). This phenomenon may suggest the presence of the mechanism associated with improvement of fat body glucose depos’ utilization in starvation conditions which is activated by dCRY binding KL001.

In addition to identifying and prosecuting cyber attackers, attack attribution activities can provide valuable information guiding the defenders’ security procedures and giving them greater confidence in incident response and remediation. However, technical analysis involved in cyberattack attribution requires high skills, experience, access to up-to-date Cyber Threat Intelligence, and significant investigators’ effort. Attribution results are not always reliable, and skilful attackers often work hard to cover their traces and mislead or confuse investigators. In this article, we present a tool designed to support technical attack attribution and implemented as a machine learning model extending the OpenCTI platform. We also discuss the tool’s performance in the investigation of a recent cyberattack.

: The article examines the regularities of structure formation of ultrafine fibers based on poly-3-hydroxybutyrat under the influence of technological (electrical conductivity, viscosity), molecular (molecular weight), and external factors (low-molecular and nanodispersed substances of different chemical nature). Systems with polar substances are characterized by the presence of intermolecular interactions and the formation of a more perfect crystalline fiber structure. Changes in technological and molecular characteristics affect the fiber formation process, resulting in alterations in the morphology of the non-woven fabric, fiber geometry, and supramolecular fiber structure. Polymer molecular weight, electrical conductivity, and solution viscosity influence fiber formation and fiber diameter. The fiber structure is heterogeneous, consisting of both crystalline and non-equilibrium amorphous phases. This is significant in the development of matrix-fibrillar systems for drug delivery, bioactive substances, antiseptics, tissue engineering constructs, tissue engineering scaffolds, artificial biodegradable implants, sorbents, and other applications.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

In the present paper, we describe several coleoid jaws discovered in the lower Toarcian black shales, cropping out along the Vilyui River (Yakutia, Russia). This is the first record of a Lower Jurassic coleoid jaw outside Europe and the first report of such a finding from the Mesozoic of Siberia. The described coleoid jaws demonstrate the same mode of preservation and morphology as the coeval jaws previously reported from Europe. Their preservation in Siberia became possible due to the widespread occurrence of black shale facies associated with the early Toarcian oceanic anoxic event (TOAE).

Triphenylphosphonium (TPP) derivatives of a decapeptide related to sequences of bactenecin 7 (Bac7) and oncocin (Onc112) were synthesized and studied as potential antimicrobial compounds using various biochemical and microbiological assays. It was shown that while the reduction of the Bac7 length to 10 a.a. residues dramatically decreases the affinity to bacterial ribosomes, the modification of peptide with alkyl-TPP moieties leads to an increase in the affinity. New analogs which structure combines a decapeptide related to Bac7 and Onc112 — Bac(1-10, R/Y) — and TPP, attached to the C-terminal amino acid residue through alkylamide linkers, inhibit translation in vitro and are found to be more selective inhibitors of bacterial translation as compared with eukaryotic translation, than Onc112 and Bac7. Triphenylphosphonium analogs of a decapeptide related to Bac7 and Onc112 suppress the growth of both gram-negative bacteria, similar to Onc112 and Bac7, and gram-positive ones as alkyl-TPP derivatives, and also act against some resistant laboratory strains. Bac(1-10, R/Y)-C2-TPP, containing a short alkylamide linker between the decapeptide and TPP, is transferred into the E. coli cells via the SbmA transporter protein. TPP derivatives of the decapeptide Bac(1-10, R/Y) containing either decylamide or ethylamide linker cause B. subtilis membrane depolarization, similar to alkyl-TPP. The Bac(1-10, R/Y)-C2-TPP analog is proved to be non-toxic for mammalian cells by MTT-test.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

In this article, the biocatalytic oxidation of ethanol into acetaldehyde was studied using a catalase entrapped within monolithic polyampholyte cryogel, p(APTAC-co-AMPS), derived from an anionic monomer, 2-acrylamido-2-methyl-1-propanesulfonic acid sodium salt (AMPS), and a cationic monomer, (3-acrylamidopropyl) trimethylammonium chloride (APTAC) as catalyst. Macroporous polyampholyte cryogels containing various amounts of catalase were synthesized in situ under cryo-polymerization conditions at a molar ratio of monomers [APTAC]:[AMPS] = 75:25 mol.% in the presence of 10 mol.% cross-linking agent, N,N-methylenebisacrylamide (MBAA). The conversion of ethanol into acetaldehyde in good-to-high yields was observed in flow-through and batch type reactors under optimal conditions: at T = 10-20 C, pH = 7.1, [C2H5OH]:[H2O2] = 50:50 vol.%. According to SEM image the pore sizes of p(AMPS-co-APTAC) cryogel vary from 15 to 55 μm. The catalytic activity of catalase entrapped within monolithic polyampholyte cryogel in the conversion of ethanol into acetaldehyde was evaluated through the determination of such kinetic parameters as Michaelis constant (Km), the maximum enzymatic rate (Vmax), activation energy (Ea), turnover number (TON) and turnover frequency (TOF). The catalase encapsulated within monolithic polyampholyte cryogel exhibits a high conversion of ethanol into acetaldehyde. The advantages and disadvantages of flow-through and batch type reactors were highlighted.

UV induced photoluminescence of organosilica films with ethylene and benzene bridging groups in their matrix and terminal methyl groups on the pore wall surface is studied to reveal optically active defects and understand their origin and nature. Careful selection of the film’s precursors and conditions of deposition and curing, analysis of chemical and structural properties led to the conclusion that luminescence sources are not associated with the presence of oxygen-deficient centers, as in the case in pure SiO2. It is shown that the sources of luminescence are the carbon-containing components that are part of the low-k-matrix, as well as the carbon residues formed upon removal of the template and UV induced destruction of organosilica samples. A good correlation between the energy of the photoluminescence peaks and the chemical composition is observed. This correlation is confirmed by the results obtained by the Density Functional theory. The photoluminescence intensity increases with porosity and internal surface area. The spectra become more complicated after annealing at 400 °C, although Fourier transform infrared spectroscopy does not show these changes. The appearance of additional bands is associated with compaction of low-k matrix and segregation of template residues on the surface of the pore wall.

S100 proteins are multifunctional calcium-binding proteins of vertebrates that act intracellularly, extracellularly, or both, and are engaged in the progression of many socially significant diseases. Their extracellular action is typically mediated by the recognition of specific receptor proteins. Besides, recent studies indicate the ability of some S100 proteins to affect cytokine signaling through direct interaction with cytokines. S100P was shown to be the S100 protein most actively involved in interactions with some of four-helical cytokines. To assess selectivity of S100P protein binding to four-helical cytokines, we have probed interaction of Ca2+-bound recombinant human S100P with a panel of 32 four-helical human cytokines covering all structural families of this fold, using surface plasmon resonance spectroscopy. 22 cytokines from all families of four-helical cytokines are S100P binders with the equilibrium dissociation constants, Kd, ranging from 1 nM to 3 µM (below the Kd value for the S100P complex with the V domain of its conventional receptor, receptor for advanced glycation end products, RAGE). Molecular docking and mutagenesis studies revealed the presence in the S100P molecule of a cytokine-binding site, which overlaps with the RAGE-binding site. Since S100 binding to four-helical cytokines inhibits their signaling in some cases, the revealed ability of S100P protein to interact with ca 71% of the four-helical cytokines indicates that S100P may serve as a poorly selective inhibitor of their action.

In the current work, in continuation of our recent research [1] we synthesized and studied new chimeric compounds comprising the ribosome-targeting antibiotic chloramphenicol (CHL) and the membrane-penetrating cation triphenylphosphonium (TPP) connected by alkyl linkers of different lengths. Using various biochemical assays, we showed that these CAM-Cn-TPP compounds bind to the bacterial ribosome, inhibit protein synthesis in vitro and in vivo in a way similar to that of the parent CHL, and significantly decrease membrane potential. Similar to CAM-C4-TPP, the mode of action of CAM-C10-TPP and CAM-C14-TPP on bacterial ribosomes differ from that of CHL. By simulating the dynamics of complexes of CAM-Cn-TPP with bacterial ribosomes, we have proposed a possible explanation for the specificity of the action of these analogs on the translation process. CAM-C10-TPP and CAM-C14-TPP stronger inhibit the growth of the Gram-positive bacteria in comparison to the CHL and suppress some strains of CHL-resistant bacteria. Thus, we have shown that TPP derivatives of CHL are dual-acting compounds that target the ribosomes and the cellular membranes of bacteria. The TPP fragment of CAM-Cn-TPP compounds contributes to the inhibitory effect on bacteria. Moreover, since the mitochondria of eukaryotic cells have qualities similar to those of their prokaryotic ancestors, we demonstrate the possibility of targeting chemoresistant cancer cells with these compounds.

In recent years, the number of mole species for which the species status has been confirmed using genetic methods has been continuously increasing. Unfortunately, cytogenetic analysis is not available for all species. Here, for the first time, a GTG-banded karyotype of the small-toothed mole from Vietnam, Euroscaptor parvidens, a representative of the eastern clade of the genus Euroscaptor, was described. Through comparative analysis of available Euroscaptor (E. parvidens, E. klossi, and E. malayana) and Oreoscaptor (O.mizura) karyotypes we find cytogenetic signatures. Zoo-FISH with sorted chromosomes of the Siberian mole Talpa altaica on chromosome sets of the small-toothed mole E. parvidens, the small Japanese mole M. imaizumii from the close genus Mogera and the Japanese shrew mole Urotrichus talpoides from the tribe Urotrichini made it possible to identify syntenic regions between species that diverged about 35 million years ago. The low rate of chromosomal changes within the species of the genus Talpa - T.altaica and T.europaea - and the high rate of karyotypic reshuffling within the Asian genera of the tribe were confirmed. The pericentric inversions on four pairs of autosomes are shared between the closely related genera Euroscaptor, Oreoscaptor, and Mogera, while many more apomorphic rearrangements have occurred in each lineage additionally. The highest rate of chromosomal changes was recorded in the lineage of the small-toothed mole.

At least 50% of factors predisposing to alcohol dependence (AD) are genetic and women affected with this disorder present with more psychiatric comorbidities, probably indicating different genetic factors involved. We aimed to run a genome-wide association study (GWAS) followed by a bioinformatic functional annotation of associated genomic regions in male and female patients with AD and eight related clinical measures. A genome-wide significant association of rs220677 with AD (p-value = 1.33×10^-8 calculated with the Yates-corrected Chi-square test under the assumption of dominant inheritance) was discovered in female patients. Associations of AD and related clinical measures with seven other single nucleotide polymorphisms listed in previous GWAS of psychiatric and addiction traits were differently replicated in male and female patients. The bioinformatic analysis showed that regulatory elements in the eight associated linkage disequilibrium blocks define the expression of 80 protein-coding genes. Nearly 68% of these and of 120 previously published coding genes associated with alcohol phenotypes directly interact in a single network. This study indicates that a number of genes behind the pathogenesis of AD are different in male and female patients, but implicated molecular mechanisms are functionally connected. The results also suggest the genetic basis of sex-specific psychiatric comorbidities of AD.

The classification of Trojans in modern analog microcircuits is considered. Using high-speed operational amplifiers (Op-Amps) as an example, the relationship between Op-Amp circuit design and the formation of undesirable states in typical switching circuits is shown. Circuit solutions are proposed to minimize the Trojan states of high-speed Op-Amps. These include limiting the maximum output currents of the input stages of the Op-Amp during the transient process and the use of differentiating transient correction circuits in the Op-Amp.

The aim of the study was to examine the long-term prognostic value of changes in cardio-ankle vascular index (CAVI) within a year after coronary artery bypass grafting (CABG). Methods. Patients with coronary artery disease (n = 251) in whom cardio-ankle vascular index (CAVI) was assessed using the VaSera VS-1000 device before and in a year after CABG. Groups with improved CAVI (CAVI decreased from pathological value to normal or the index remained within normal values) or worsened CAVI (persistent pathological index value or an increase in CAVI to pathological values or an increase of 1 unit or more) were identified. The groups were compared for the following events at 10-year follow-up: death from all causes, myocardial infarction, stroke/transient ischemic attack, and the combined endpoint. Results. A year after CABG surgery, 45% of patients showed positive dynamics or stable normal CAVI values. Death from all causes was significantly more common in the group with CAVI progression - 32 (27.6%) than in the group with CAVI improvement - 14 (14.8%; p = 0.029). Patients with CAVI progression were more likely to have MACE (death, MI, stroke/TIA) in 49 (42.2%) cases, compared with patients with CAVI improvement - in 23 (24.5%; p=0.008). Negative dynamics of CAVI (p = 0.024), number of shunts (p = 0.006), and the presence of carotid stenosis more than 30% (p = 0.051) were independent predictors of death from all causes at 10-year follow-up after CABG. The presence of carotid stenosis more than 30% (p = 0.002) and the group with negative dynamics of CAVI after a year (p = 0.008) were independent predictors of the development of the combined endpoint during long-term follow-up. Conclusions. Patients with negative dynamics of CAVI one year after CABG were more likely to experience death from all causes and combined endpoint in the long-term follow-up than patients with normal CAVI. In further studies, it is advisable to evaluate the dynamics of CAVI and, based on this, identify the most effective interventions to improve the prognosis of patients after CABG.

Colletotrichum lini is a flax fungal pathogen, comprising differently virulent strains. In this work, we sequenced the genomes of three C. lini strains of different virulence: high virulent #390-1, medium virulent #757, and low virulent #771. We obtained more than 100× genome coverage with Oxford Nanopore Technologies reads and more than 50× genome coverage with Illumina data. To construct high-quality genomes, several assembly strategies were tested. The final assemblies were obtained using the Canu – Racon ×2 – Medaka – Polca scheme and were 54.0-55.3 Mb in length, contained 26-32 contigs, had an N50 > 5 Mb and the BUSCO completeness > 96%. Comparative analysis of the constructed genomes showed high similarity between mitochondrial and nuclear genomes. However, a rearrangement event and the loss of a 0.9 Mb contig were revealed. The candidate effectors were predicted in sets of proteins received after genome annotation. The obtained genome sequences of C. lini strains extend the knowledge on the genetic diversity of Colletotrichum species and are the basis for establishing molecular mechanisms of pathogenicity of the flax pathogen and effective control of flax anthracnose.

A hallmark of Alzheimer’s disease (AD) are the proteinaceous aggregates formed by the amyloid-beta peptide (Aβ) that is deposited inside the brain as amyloid plaques. The accumulation of aggregated Aβ may initiate or enhance pathologic processes in AD. According to the amyloid hypothesis any agent that has the capability to inhibit Aβ aggregation and/or destroy amyloid plaques represents a potential disease modifying drug. In 2023, a humanized IgG1 monoclonal antibody (lecanemab) against the Aβ soluble protofibrils was approved by US FDA for AD therapy thus providing compelling support to the amyloid hypothesis. To acquire a deeper insight on the in vivo Aβ aggregation, various animal models, including aged herbivores and carnivores, non-human primates, transgenic rodents, fish and worms are widely exploited. This review is based on the recent data obtained using transgenic animal AD models and presents experimental verification of the critical role in Aβ aggregation seeding of the interactions between zinc ions, Aβ with the isomerized Asp7 (isoD7- Aβ) and the α4β2 nicotinic acetylcholine receptor.

Helicobacter Pylori (H. Pylori) is a common pathogen with high prevalence of infection in human populations. Diagnosis of H. Pylori infection is critical for its treatment, eradication, and prognosis. Biosensors have been demonstrated to be powerful for rapid onsite detection of pathogens, particularly for point-of-care test (POCT) scenarios. In this work, we propose a novel optical biosensor, based on nanomaterial porous silicon (PSi) and photonic surface state Tamm Plasmon Polariton (TPP), for detection of cytotoxin-associated antigen A (CagA) antigen of H. Pylori bacterium. We fabricated the PSi TPP biosensor, analysed its optical characteristics and demonstrated through experiments towards sensing of CagA antigen, that TPP biosensor has sensitivity of 100 pm/(ng/ml), limit of detection of 0.01 ng/ml, and specificity in terms of positive-to-negative ratio of more than six. From these performance factors, it can be concluded that TPP biosensor can serve as an effective tool for diagnosis of H. Pylori infection, either in analytical labs or in POCT applications.

We present a very computationally light and fast approximation algorithm and then verify it with genetic algorithm and simulated annealing. We show that our algorithm is on par with GA and SA in terms of output produced while having a tightly bounded time complexity. Our algorithm works best when there is a strong positive correlation between the reliability of a component and its cost. We present two algorithms with the same essence. One of them is system cost bounded and the other is target reliability bounded. Our proposed algorithm works on a subsystem level redundancy instead of component level redundancy.

Sulfite and kraft pulping are two principal methods of industrial delignification of wood. In recent decades, those have been considered as possibilities to pretreat recalcitrant wood lignocellulosics for enzymatic hydrolysis of polysaccharides and subsequent fermentation of obtained sugars to valuable bioproducts. Current work compares chemistry and technological features of two different cooking processes in the preparation of polysaccharide substrates for deep sacchari-fication with P. verruculosum glycosyl hydrolases. Bleached kraft and sulfite pulps were subjected to hydrolysis with enzyme mixture of high xylanase, cellobiohydrolase and β-glucosidase activities at a dosage of 10 FPU/g of dry pulp and fiber concentration of 2.5, 5 and 10%. HPLC was used to analyze soluble sugars after hydrolysis and additional acid inversion of oligomers to monosaccharides. Kraft pulp demonstrated higher pulp conversion after 48 h (74-99%), mostly resulted from deep xylan hydrolysis. Sulfite-pulp hydrolysates, obtained in similar conditions, due to higher hexose concentration (more than 50 g/L), had higher fermentability for industrial strains producing alcohols, microbial protein or organic acids. Along with saccharification, enzymatic modification of non-hydrolysed residues occurred, which led to decreased degree of polymerization and composition changes in two industrial pulps. As a result, crystallinity of kraft pulp increased by 1.3%, which opens possibilities for obtaining new types of cellulosic products in pulp and paper industry. The high adaptability and controllability of enzymatic and fermentation processes creates prospects for the modernization of existing factories.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

Fokker-Planck PDEs (incl. diffusions) for stable Lévy processes (incl. Wiener processes) on the joint space of positions and orientations play a major role in mechanics, robotics, image analysis, directional statistics and probability theory. Exact analytic designs and solutions are known in the 2D case, where they have been obtained using Fourier transform on $SE(2)$. Here we extend these approaches to 3D using Fourier transform on the Lie group $SE(3)$ of rigid body motions. More precisely, we define the homogeneous space of 3D positions and orientations $\mathbb{R}^{3}\rtimes S^{2}:=SE(3)/(\{\mathbf{0}\} \times SO(2))$ as the quotient in $SE(3)$. In our construction, two group elements are equivalent if they are equal up to a rotation around the reference axis. On this quotient we design a specific Fourier transform. We apply this Fourier transform to derive new exact solutions to Fokker-Planck PDEs of $\alpha$-stable Lévy processes on $\mathbb{R}^{3}\rtimes S^{2}$. This reduces classical analysis computations and provides an explicit algebraic spectral decomposition of the solutions. We compare the exact probability kernel for $\alpha = 1$ (the diffusion kernel) to the kernel for $\alpha=\frac12$ (the Poisson kernel). We set up SDEs for the Lévy processes on the quotient and derive corresponding Monte-Carlo methods. We verify that the exact probability kernels arise as the limit of the Monte-Carlo approximations.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

Cotton is the most ubiquitous and profitable fiber with diverse industrial and domestic applications. Grown in over 100 countries, it has a global market value of about $40 billion and employs over 350 million people from fields to textile mills, contributing about 7% of total labor-force recruitment in developing economies. Cotton has an indeterminate growth habit and an extensive tap root system affected by soil physicochemical and environmental conditions. There is a consensus among experts that conventional cotton cultivation still has a long way to attain sustainability, which is essential if cotton will maintain its competitive edge over other natural and synthetic fibers like hemp, polyesters, and rayon. Despite several efforts already committed to growing cotton sustainably, sustainability has eluded cotton cultivation globally because of the intense farm inputs (freshwater, pesticides, and heavy-duty equipment) needs, especially in developing economies. Some of the technological advancements towards achieving the goal of sustainable cotton cultivation include the development of new varieties, improved irrigation and mulching and precision agriculture techniques, application of remote sensing and Unmanned Aerial Systems (UAS) combined with image processing, and the introduction of autonomous and multi-purpose robotic platforms for growing and harvesting cotton. This review attempts to evaluate the successes already achieved by stakeholders in moving cotton towards sustainable production and identify areas where efforts are still needed to reach sustainable production and improved profitability goals for cotton with projections for future research directions.

Tyrosyl-DNA phosphodiesterase 1 (TDP1) is a human DNA repair protein. It is a member of the phospholipase D family based on the structure similarity. TDP1 is a key enzyme involved in repairing stalled topoisomerase 1 (TOP1)-DNA complexes. Previously we obtained with the CRISPR/Cas9 method HEK293A cells with the homozygous knockout of the Tdp1 gene and used knockout cells as a cellular model for studying the mechanisms of anticancer therapy. In this work we studied for the first time by transcriptomic analysis the effect of Tdp1 gene knockout on genes expression changes in human HEK293A cell line. We received original data that may indicate a role of TDP1 in other process besides repair of DNA-TOP1 complex. The differentially expressed genes (DEGs) analysis revealed that TDP1 could be involved in different processes such as cell adhesion and communication, spermatogenesis, mitochondrial function, neurodegeneration, cytokine response, and MAPK pathway signaling.

A Pt(II) complex featuring chelating tridentate bis-aryloxide tetrahydropyrimidinium based N-heterocyclic carbene (NHC) was synthesized and characterized by using different techniques. The electrochemical properties of the complex were investigated by cyclic voltammetry as well as differential pulse voltammetry, which revealed two reversible one-electron oxidation processes. The chemical generation and isolation of one-electron-oxidized species were performed oxidizing the initial complex by means of AgBF4. The combined UV-Vis/NIR- and EPR-spectroscopy studies supported by density functional theory (DFT) calculations suggest the formation of Pt(II)-phenoxyl radical complex. The latter open-shell derivative was structurally characterized by means of X-ray diffraction analysis. Finally, the neutral platinum complex was tested as a mediator in the process of electrocatalytic oxidation of 2-(methylamino)ethanol (MEA).

Working memory refers to the capability of the nervous system to selectively retain short-term memories in an active state. The long-standing viewpoint is that neurons play an indispensable role and working memory is encoded by synaptic plasticity. Furthermore, some recent studies have shown that calcium signaling assists the memory processes and the working memory might be affected by the astrocyte density. Over the last few decades, growing evidence has also revealed that astrocytes exhibit diverse coverage of synapses which are considered to participate in neuronal activities. However, very little effort has yet been made to attempt to shed light on the potential correlations between these observations. Hence, in this article we will leverage a computational neuron-astrocyte model to study the short-term memory performance subject to various astrocytic coverage and we will demonstrate that the short-term memory is susceptible to this factor. Our model may also provide plausible hypotheses for the various sizes of calcium events as they are reckoned to be correlated with the astrocytic coverage.

An efficient approach to the previously unknown furo[2',3':2,3]pyrrolo[2,1-a]isoquinoline deriv-atives from readily available 1-R-1-ethynyl-2-vinylisoquinolines is described. The reaction fea-tures a simple procedure, occurs in hexaflouroisopropanol and does not require elevated tem-peratures. It has been found that the addition of glacial acetic acid significantly increases the yields of the target spirolactone products. Using trifluoroethanol instead of hexaflouroisopro-panol results into formation of pyrido[2,1-a]isoquinolines.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

Granulocyte-macrophage colony-stimulating factor (GM-CSF) is a pleiotropic myelopoietic growth factor and proinflammatory cytokine, clinically used for multiple indications and serving as a promising target for treatment of many disorders, including cancer, multiple sclerosis, rheumatoid arthritis, psoriasis, asthma, COVID-19. We have previously shown that dimeric Ca2+-bound forms of S100A6 and S100P proteins, members of the multifunctional S100 protein family, are specific to GM-CSF. To probe selectivity of these interactions, the affinity of recombinant human GM-CSF to dimeric Ca2+-loaded forms of 18 recombinant human S100 proteins was studied by surface plasmon resonance spectroscopy. Of them, only S100A4 protein specifically binds to GM-CSF with equilibrium dissociation constant, Kd, values of 0.3-2 μM, as confirmed by intrinsic fluorescence and chemical crosslinking data. Calcium removal prevents S100A4 binding to GM-CSF, whereas monomerization of S100A4/A6/P proteins disrupts S100A4/A6 interaction with GM-CSF and induces a slight decrease in S100P affinity for GM-CSF. Structural modelling indicates the presence in the GM-CSF molecule of a conserved S100A4/A6/P-binding site, consisting of the residues from its termini, helices I and III, some of which are involved in the interaction with GM-CSF receptors. The predicted involvement of the ‘hinge’ region and F89 residue of S100P in GM-CSF recognition was confirmed by mutagenesis. Examination of S100A4/A6/P ability to affect GM-CSF signaling showed that S100A4/A6 inhibit GM-CSF/S100-induced suppression of viability of monocytic THP-1 cells. The ability of the S100 proteins to modulate GM-CSF activity is relevant to progression of various neoplasms and other diseases, according to bioinformatics analysis. The direct regulation of GM-CSF signaling by extracellular forms of the S100 proteins should be taken into account in the clinical use of GM-CSF and development of the therapeutic interventions targeting GM-CSF or its receptors.

ExuR and UxuR are paralogous proteins belonging to the GntR family of transcriptional regulators. Both are known to control hexuronic acid metabolism in a variety of Gammaproteobacteria but the relative impact of each of them is still unclear. Here, we apply 2D difference electrophoresis followed by mass-spectrometry to characterise the changes in the Escherichia coli proteome in response to the uxuR or exuR deletion. Our data clearly show that the effects are different: deletion of uxuR resulted in significantly enhanced expression of D-mannonate dehydratase UxuA and flagellar protein FliC, and inhibition of outer membrane porin OmpF, while the absence of ExuR did not significantly alter the spectrum of detected proteins.This suggests that the roles of proteins predicted as homologs are far from identical. Effects of uxuR deletion were largely dependent on the cultivation conditions: during growth with glucose, UxuA and FliC were dramatically altered, while during growth with glucuronate activation of both was not so prominent. During growth on glucose, the maximal activation was detected for FliC. This was further confirmed by expression analysis and physiological tests thus suggesting involvement of UxuR in the regulation of bacterial motility and biofilm formation.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

The hydrodynamics of plasma formed in the interaction of 100-ns UV KrF laser pulses with foam targets with volume densities from 5 to 500 mg/cm3 was studied. Initial and dynamic transmittance at 248-nm wavelength have been measured. At intensities about 1012 W/cm2, the propagation rates of radiation through foam targets reached 80 km/s, while plasma stream velocities from both front and rear sides of targets were approximately the same ~ 75 km/s, which confirms a volumetric absorption of radiation within the target thickness and the explosive nature of the plasma formation and expansion.

Recent years witnessed progressive broadening of the practical use of 3D-printed aluminium alloy parts, in particular for specific aerospace applications where weight saving is of great importance. Selective laser melting (SLM) is an intrinsically multi-parametric fabrication technology that offers multiple means of controlling mechanical properties (elastic moduli, yield strength, ductility) through the control over grains size, shape, and orientation. Ultimately, this approach implies that structural elements can be purposefully fabricated to reinforce specific zones and directions where higher mechanical loads are anticipated by design. Targeted control over mechanical properties is achieved through the tuning of 3D-printing parameters and may even obviate the need of heat treatment or mechanical post-processing. Systematic studies of grain structure for different printing orientation with the help of EBSD techniques in combination with mechanical testing at different dimensional levels are the necessary first steps to implement this agenda. Samples of 3D-printable Al-Mg-Si RS-333 alloy were fabricated in 3 orientations with respect to the principal build direction and the fast laser beam scanning direction. Sample structure and proper-ties were investigated using a number of techniques, including EBSD, in situ SEM tensile testing, roughness measurements and nanoindentation. The as-printed samples we found to display strong variation in Young’s modulus values from nanoindentation (from 43 to 66 GPa) and tensile tests (from 54 to 75 GPa), yield stress and ultimate tensile strength (100…195 and 130…220 MPa) in different printing orientations, and almost constant hardness of about 0.8 GPa. A further preliminary study was conducted of the effect of surface finishing on the mechanical performance. Surface polishing appears to reduce Young’s modulus and yield strength, but improves ductility, whereas the influence of sand blasting is more controversial. The experimental results are dis-cussed in connection with the grain morphology and orientation.

Cereal crops, such as oats and barley, possess a number of valuable properties that meet the requirements for functional diet components. This review summarized the available information about bioactive compounds of oat and barley grain. The results of studying the structure and physicochemical properties of the cell wall polysaccharides of barley and oat are presented. The main components of the flavonoids formation pathway are shown and data, concerning anthocyanins biosynthesis in various barley tissues, are discussed. Moreover, we analyzed the available information about structural and regulatory genes of anthocyanin biosynthesis in Hordeum vulgare L. genome, including β-glucan biosynthesis genes in Avena sativa L species. However, there is not enough knowledge about genes responsible for biosynthesis of β-glucans and corresponding enzymes and plant polyphenols. The review also covers contemporary studies about collections of oat and barley genetic resources held by VIR. This review intended to provide information on the processes of biosynthesis of biologically active compounds in cereals that will promote further researches devoted to transcription factors controlling expression of structural genes and their role in other physiological processes in higher plants. Found achievements will allow breeders to create new highly productive varieties with the desirable properties.

COVID-19 pandemic provoked a number of restrictive measures, such as the closure or severe restriction of border transit for international trading traffic, quarantines and self-isolation. This caused a series of interrelated consequences that not only prevent or slow down the spread of disease, but also impact the medical systems’ capability to treat the patients and help their recovery. In particular, steeply growing demand for medical safety goods cannot be satisfied by regular suppliers due to the shortage of raw materials originating from other countries or remotely located national sources, under conditions of quarantined manpower. The current context inevitably brings back memories (and records!) of the situation 80 years ago, when WWII necessitated major effort directed at the rapid build-up of low cost mass production to satisfy all aspects of war-time need. In the present short report we document a successful case of fast mass-production of light transparent medical safety face shields (thousands per day) realized in Skolkovo Institute of Science and Technology (Skoltech) fabrication laboratory (FabLab). The demand for safety face shields by tens of hospitals in Moscow City and Region rapidly ramped up due to the need to protect medical staff during patient collection and transportation to hospitals, and within both the infected (“red”) and uninfected (“green”) zones. Materials selection for sterilizable transparent materials was conducted based on the analysis of merit indices, namely, minimal weight at given stiffness and minimal cost at given stiffness. Due to the need for permanent wear, design was motivated by low weight and comfortable head fixation, along with high production efficiency. The selection of minimal tooling in University fabrication workshops and the use of distributed volunteer labor are discussed.

The zero offset voltage in anti-aliasing low-pass filters (LPF) included at the ADC input has a significant effect on the effective bit rate of the ADC. The article discusses methods for minimizing the systematic component of the zero offset voltage (V_OS) of operational amplifiers (Op-Amp) in the structure of the LPF, due to the degradation of the current gain of the base (b) of bipolar transistors for an extremely common subclass of Op-Amp with one high-impedance node. The methods of matching a high-impedance Op-Amp node and a buffer amplifier with the help of special correcting SCM^p and SCMⁿ multipolars are proposed. Methods of description and formation of the given coefficients of weak current asymmetry of typical Op-Amp functional units (current mirrors, input DS, buffer amplifiers, SRC, etc.) are presented. As an example, the results of computer simulation of GaAs Op-Amp with small V_OS performed on JFET field and p-n-p bipolar transistors are given.

More than 20 years after the discovery of the first anelloviruses (AVs), they still remain a mysterious group of viruses. To date, there is no clear understanding of their impact on the host organism, although information is emerging about their participation in various pathologies. However, it is well known that AVs are an important component of the human virome. In the current study we assessed the abundance of AVs in viromes from four nasal and pharyngeal samples from children with respiratory symptoms using a metagenomic approach. It is worth noting that three patients had known respiratory viruses and one did not have any. Regarding AVs, they were detected in all samples, namely Torque teno mini virus (TTMV). The greatest abundance and diversity of AVs (Torque teno virus (TTV), TTMV and Torque teno midi virus (TTMDV)) were shown in a diseased patient with an absence of respiratory viruses, which may indicate the potential involvement of AVs in the maintenance of respiratory symptoms. An activated immune system to combat the main pathogens, against the background of which the number of AVs decreases, is discussed as a possible reason for the reduced diversity of anellome in other patients. We also compared the results of the metagenomic approach and qPCR for major respiratory viruses, which were in agreement. In addition, metagenomic sequencing made it possible to obtain additional data on viral genomes in order to establish their taxonomic identification and characterize individual viral profiles in patients from the Siberian part of Russia.

Magnetogenetics emerges as a transformative approach for modulating cellular signaling pathways through the strategic application of magnetic fields and nanoparticles. This technique leverages the unique properties of magnetic nanoparticles (MNPs) to induce mechanical or thermal stimuli within cells, facilitating the activation of mechano- and thermosensitive proteins without the need for traditional ligand-receptor interactions. Unlike traditional modalities that often require invasive interventions and lack precision in targeting specific cellular functions, magnetogenetics offers a non-invasive alternative with the capacity for deep tissue penetration and the potential for targeting a broad spectrum of cellular processes. This review underscores magnetogenetics' broad applicability, from steering stem cell differentiation to manipulating neuronal activity and immune responses, highlighting its potential in regenerative medicine, neuroscience, and cancer therapy. Furthermore, the review explores the challenges and future directions of magnetogenetics, including the development of genetically programmed magnetic nanoparticles and the integration of magnetic field-sensitive cells for in vivo applications. Magnetogenetics stands at the forefront of cellular manipulation technologies, offering novel insights into cellular signaling and opening new avenues for therapeutic interventions.

Additive manufacturing (3D printing) and computer-aided design (CAD) still have limited up-take in biomedical and bioengineering research and education, despite the significant potential of these technologies. The utility of organ-scale 3D-printed models of living structures is widely appreciated, while the workflows for microscopy data translation into tactile-accessible replicas are not well developed yet. Here, we demonstrate an accessible and reproducible CAD-based methodology for generating 3D-printed scalable models of human cells cultured in vitro and imaged using conventional scanning confocal microscopy and fused deposition modelling (FDM) 3D printing. We termed this technology CiTo-3DP (Cells-in-Touch for 3D Printing). As a proof-of-concept, we created CiTo-3DP models of human pancreatic cancer cells and healthy dermal fibroblasts by using selectively stained nuclei and the cytoskeleton components (f-actin and α-smooth muscle actin). The production of dismountable sets of cellular components was al-so shown. The CiTo-3DP approach can be adapted to comprehensively present various cell types, subcellular structures and extracellular matrices. We envisage that the resulting CAD and 3D printed models could be used for further applications, including but not limited to in silico simulations for biology, medicine, pharmacological research, tissue engineering, morphometrical analysis, multiphysics modelling, education, rehabilitation of visually impaired people, and integration into virtual reality.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.