Availability and continuous operation under critical conditions are very important in electric machine drive systems. However, such systems, are suffering from several type of failures that affect the electric machine or the associated voltage source inverter. Therefore, fault diagnosis and fault tolerance are highly required. This paper presents a new robust deep learning-based approach to diagnosis multiple open-circuit fault in three phase two level voltage source inverter for induction motor drive applications. The proposed approach uses fault diagnosis variables obtained from sigmoid transformation of the motor stator currents. The open-circuit fault diagnosis variables are then introduced to a Bidirectional Long Short-Term Memory algorithm to detect the faulty switch(es). Several simulation and experimental results are presented to show the proposed fault diagnosis algorithm effectiveness and robustness.

: Early and accurate detection of infectious diseases is a key step for surveillance, epidemiology, and control, notably timely disease diagnosis, patient management and follow-up. In this study, we aimed to develop hand-held ultra-fast duplex PCR assays coupled to amplicon detection by lateral flow (LF) immunoassay to deliver a rapid, and simple molecular diagnostic test for con-comitant detection and identification of the main Leishmania parasites encountered in Tunisia and the Old World. We selected two DNA targets to amplify L. major/L. tropica and L. infantum/L. tropica group of species DNAs, respectively. We optimized the experimental conditions of a du-plex ultra-fast PCR. The amplification is performed by a portable Palm convection PCR machine within 18 min and the products are detected by a LF cassette within 10 minutes. The test allows the identification of the infecting species according to the position and number of test lines re-vealed. Tested on a selection of DNAs of representative Leishmania strains of the three studied species (N=37), the ultra-fast duplex PCR-LF showed consistent, stable, and reproducible results. The analytical limit of detection of the test was 0.4pg for L. major, 4pg for L. infantum and 40pg for L. tropica.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

This study challenges the prevailing belief in the necessity of complex models for accurate forecasting by demonstrating the effectiveness of parsimonious econometric models, namely ARCH(1) and GARCH(1,1), over deep learning robust approaches, such as LSTM and 1D-CNN neural networks, in modeling historical volatility within pre-emerging stock markets, specifically the Moroccan and Bahraini stock markets. The findings suggest reevaluating the balance between model complexity and predictive accuracy. Future research directions include investigating the potential existence of threshold effects in market capitalization for optimal model performance. This research contributes to a deeper understanding of volatility dynamics and enhances forecasting models’ effectiveness in diverse market conditions.

Cell aging is associated with the increased production of mitochondrial reactive oxygen species (mtROS) due to mitochondrial dysfunction, and various phytonutrients and estrogens have been shown to improve skin health. Thus, the aim of the current study was to examine damage to dermal fibroblasts by chemically-induced mitochondrial dysfunction and to study the mechanism of the protective effects of carotenoids, polyphenols, and estradiol. Rotenone, a Complex I inhibitor, caused mitochondrial dysfunction in human dermal fibroblasts, substantially reducing respiration and ATP levels, followed by increased mitochondrial and cytosolic ROS, which resulted in apoptotic cell death, increased matrix metalloproteinase-1 (MMP1) secretion, and decreased collagen secretion. Pre-treatment with carotenoid-rich tomato extracts, rosemary extract, and estradiol reversed these effects. These protective effects can be partially explained by a cooperative activation of antioxidant response element (ARE/Nrf2) transcriptional activity by the protective compounds and rotenone, which led to upregulation of antioxidant proteins such as NQO1. To determine if ARE/Nrf2 activity is crucial for cell protection, we inhibited it using the Nrf2 inhibitors ML385 and ochratoxin A. This inhibition markedly reduced the protective effects of the test compounds by diminishing their effect to reduce cytosolic ROS. Our study results indicate that phytonutrients and estradiol protect skin cells from damage caused by mitochondria-generated ROS and, thus, may delay skin aging and improve skin health.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Pseudomonas aeruginosa is an opportunistic Gram-negative bacterium that remains a prevalent clinical and environmental challenge. Quorum sensing (QS) molecules are effective biomarkers in pinpointing the presence of P. aeruginosa. This study aimed to develop a convenient-to-use whole-cell biosensor using P. aeruginosa reporters individually encapsulated within alginate-poly-L-lysine (alginate-PLL) microbeads to specifically detect the presence of bacterial autoinducers. The PLL-reinforced microbeads were prepared using a two-step method involving ionic crosslinking and subsequent coating with thin layers of PLL. The alginate-PLL beads showed good stability in the presence of a known cation scavenger (sodium citrate), which typically limits the widespread applications of calcium alginate. In media containing synthetic autoinducers, such as N-(3-oxo dodecanoyl) homoserine lactone (3-oxo-C12-HSL) and N-butanoyl-L-homoserine lactone (C4-HSL) or cell-free supernatants of planktonic or flow cell biofilm effluent of wild P. aeruginosa (PAO1), the encapsulated bacteria enabled a dose-dependent detection of the presence of these QS molecules. The prepared bioreporter beads remained stable during prolonged storage at 4 and -80 °C and were ready for on-the-spot sensing without the need for recovery. This whole-cell biosensor demonstrates the practicality of the encapsulated bioreporter for bacterial detection based on specific QS molecules.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

Dynamic visualizations have been developed to exchange information that transforms over time across a broad range of professional and academic contexts. However, these visual tools may impose substantial demands on the learner’s cognitive resources that are very limited in current knowledge. Cognitive load theory has been used to improve learning from dynamic visualizations by providing certain design techniques to manage learner cognitive load without adding any oral/written explanations. This systematic review examined a series of experimental studies assessing the roles of these design techniques in learning tactical scenes of play through dynamic visualizations. Electronic databases PubMed and Google Scholar were used to search relevant articles. Eleven studies were eventually included for the systematic review based on the eligibility criteria. The present review revealed that adapting design techniques to the level of learners’ expertise, type of depicted knowledge, and level of content complexity is a crucial part of effective learning.

The main purpose of our research is the evaluation of the efficacity of solvent polarity on phenolic composition, as well as the antibacterial, and antioxidant activities of extract of Moroccan Mentha aquatica L., leaves. To attempt these objectives, the HPLC-DAD was used to identify the biomolecules. The total amount of phenolic and flavonoid content was determined using the Folin-Ciocalteu and aluminum trichloride processes as well as the DPPH, RP, and TAC tests were used to evaluate the antioxidant capabilities. In addition, by employing both in vitro and in silico analysis through the microdilution method, the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the extracts were assessed against multidrug-resistant bacteria. Furthermore, the High-Performance Liquid Chromatography (HPLC) analysis indicated that all extracts of M. aquatica were abundant in noteworthy phytochemical compounds, especially gallic acid, vanillic acid, chlorobenzoic acid, quercetin, and kaempferol. Furthermore, the results indicated that the total phenolic content was higher in hydroethanolic extract (62.19 ± 1.19 mg GAE/g DW) in contrast to the acetonic and aqueous extracts (22.22 ± 0.64, and 22.44± 0.57 mg GAE/g DW) respectively. Similarly, the aqueous ethanol extract contained the greatest flavonoid concentration, with values of 29.15± 0.09 mg QE/g DW when compared with the other extracts. The seam extract poses excellent antioxidant power with an IC50 of 0.06 ± 0.00 mg/mL for the DPPH test, and lower RP with EC50 of 80± 0.00 µg/ml when compared with acetonic and aqueous extract (370± 0.00 and 460± 0.01 µg/mL) respectively. Moreover, the hydroethanolic extract has a high level of TAC 75.09± 2.00 mg EAA/g DW, followed by aqueous extract carrying a value of 28.53 ± 1.36 mg EAA/g DW. The antibacterial capacity is ranged between 0.78 ± 0.05 mg/mL and 12.60 ± 0.00 mg/L. The results of the in-silico study demonstrated that quercetin, vanillic acid, and naringenin components contribute to the antioxidant capability. While gallic acid, kaempferol, and quercetin components are attributed to the antibacterial capacity.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

Abstract: Cherubism is a rare genetic disorder characterized by painless bilateral expansion of the mandible and maxilla. We present an unusual case of a 50-year-old female patient with Ramon syndrome, a rare variant of cherubism, accompanied by gingival fibromatosis. The patient exhibited symptoms of short stature, mental retardation, rheumatoid arthritis, epilepsy, hirsutism, and gingival enlargement. Clinical examination revealed generalized gingival inflammation with plaque and attachment loss. Radiographically, bilateral defined multilocular radiolucencies were observed in the mandibular body and ramus. The patient underwent a non-surgical phase, including oral hygiene motivation and periodontal debridement, followed by a surgical phase involving gingivoplasty and internal bevel gingivectomy with open flap debridement. Histopathological analysis confirmed the presence of fibroblasts, multinucleated giant cells, and fibrous connective tissue. The patient's son also presented with bilateral facial swelling and similar radiographic findings, indicating familial inheritance of cherubism. The case demonstrates the clinical, radiographic, and histopathological features of cherubism associated with gingival fibromatosis and highlights the challenges in diagnosis and management. Regular follow-up and maintenance are essential for long-term stability and prevention of recurrence. This report contributes to the limited literature on cherubism in older patients and emphasizes the importance of early identification and intervention in affected individuals.

The stringency of GMO regulation affects trade of agricultural products among countries. On that account, our investigation attempts to shed the light on the complexity of the impact of genetically modified organisms (GMO) regulations among countries on bilateral trade with a focus on GMO approvals. We develop a framework extending Xiong and Beghin (2014) and their decomposition of export supply and imports demand effects. Our approach encompasses the supplemental effect of GMO regulation laxity in production on the exporter’s productivity. It decomposes three effects that impact bilateral trade flows between trade partners: productivity in the source country, sorting cost from bilateral dissimilarity in regulations, and stringency impact on import demand. We estimate the model using a panel dataset of corn trade and two econometric approaches (PPML, Heckman sample-selection). We find that GMO laxity in production of exporters has the most prominent and robust effect of enhancing bilateral trade of corn. The effect of GMO laxity in demand appears to be smaller than the export booster effect of GMO adoption. Finally, bilateral dissimilarity in regulations does not appear to matter, once we account for the impact of GMO in production of the exporters and laxity in demand differentiated for importer and exporters. Hence, GMO approval regulations have dominating multilateral effects rather than bilateral ones.

Corrosion inhibitors are the natural or synthetic compounds that have the ability to inhibit the average of corrosion and reduce the damage of the mild steel. Enormous organic inhibitors nowadays employed in the corrosion domain but excluded due to costly. Comparatively cheap, and stable organic compound, namely 3-((4-nitrobenzylidene)amino)coumarin, have been utilized as an excellent corrosion inhibitor in hydrochloric acid for mild steel. The inhibition efficiency has been figured regarding to weight loss method. The corrosion inhibitor was identified according to spectroscopic techniques namely Fourier transform infrared and nuclear magnetic resonance in addition to micro-elemental analysis. Inhibition efficiency for the studied inhibitor was 71.4% that, at the highest studied concentration.

Persistent organic pollutants (POPs) accumulation and hypoxia are two factors proposed to adversely alter adipose tissue (AT) functions in the context of excess adiposity. Studies have shown that preadipocytes exposure to dioxin and dioxin-like POPs have the greatest deleterious impact on rodent and immortalized human preadipocyte differentiation, but evidence on human preadipocytes is lacking. Also, hypoxia is known to strongly interfere with the dioxin-response pathway. Therefore, we tested the effects of pre-differentiation polychlorinated biphenyl (PCB)126 exposure and subsequent differentiation under hypoxia on human subcutaneous adipocytes (hSA) differentiation, glucose uptake and expression of selected metabolism- and inflammation-related genes. Pre-differentiation PCB126 exposure lowered the ATP content, glucose uptake and leptin expression of mature adipocytes but had limited effects on differentiation under normoxia (21% O2). Under hypoxia (3% O2), preadipocytes ability to differentiate was significantly reduced as reflected by significant decreased lipid accumulation and downregulation of key adipocyte genes such as PPARγ and adiponectin. Hypoxia increased glucose uptake and GLUT1 expression but abolished the adipocytes insulin response and GLUT4 expression. Expression of pro-inflammatory adipokine IL-6 was slightly increased by both PCB126 and hypoxia, while IL-8 expression was significantly increased only following the PCB126-hypoxia sequence. These observations suggest that PCB126 do not affect human preadipocyte differentiation, but do affect the subsequent adipocytes population, as reflected by lower ATP levels and absolute glucose uptake. On the other hand, PCB126 and hypoxia exert additive effects on AT inflammation, an important player in the development of chronic diseases such as type 2 diabetes and cardiovascular diseases.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

The present work is focused on the numerical solution of the complete energy equation used in fluid film lubrication. The work was motivated by the fact the complete energy equation has no analytic solution that could be used for validations. Its accuracy and computation time are related to the employed numerical method and to the grid resolution. The natural discretization method (NDM) applied on different grids is systematically compared with the spectral method (the Lobatto Point Colocation Method or LPCM) with different polynomial degrees. A one dimensional inclined slider is used for the numerical tests and the energy equation is artificially decoupled from Reynolds. This approach enables to focus all the attention on the numerical solution of the energy equation. The results show that the LPCM is one or two orders of magnitudes more efficient than the NDM in terms of computation time. The energy equation is then coupled with Reynolds equation in a thermo-hydrodynamic analysis of the same 1D slider; the numerical results confirm again the efficiency of the LPCM. A thermo-hydrodynamic analysis of a two-lobe journal bearing is then presented as a practical application.

Due to its application as an anti-cancer drug, pazopanib (1) has attracted the interest of many researchers and several studies on pazopanib synthesis have been reported over the years. This paper provides a novel route for synthesizing N,2,3-trimethyl-2H-indazol-6-amine (5) which is a crucial building block in the synthesis of pazopanib from 3-methyl-6-nitro-1H-indazole (6). By alternating between the reduction and two methylation steps compound 5 was obtained in comparable yield (55.0%) to what has been reported (54%). Noteworthy, the last step of N2-methylation also yielded N,N,2,3-tetramethyl-2H-indazol-6-amine (5’) as a new compound ever reported. Furthermore, the data presented in this paper can serve as instrumental for future research aimed at further refining the synthesis process of pazopanib.

There is a need for strategic healthcare workforce planning to address shortages and ensure universal health coverage, aiming to optimize work-force per population ratio, distribution, and competencies. Amidst rising demands exacerbated by aging populations and events like the COVID-19 pandemic, strategic workforce planning becomes crucial for addressing healthcare inequalities by forecasting needs, bridging skill gaps, and adapting to changing demographics and care models. Israel has invested in strategic planning to tackle healthcare workforce challenges; however, globally there is insufficient planning informed by health labor market analysis, which hinders efforts to address healthcare inequalities. The paper reviews national policies in Israel, Australia, Germany, and Norway, ex-amining statistics and government publications to highlight strategic plan-ning considerations and address challenges in healthcare workforce plan-ning. This paper focuses both on the critical role of physicians in healthcare systems, and on the changing borders between healthcare professions and different national contexts which demand more context dependent strategic workforce planning. We highlight common themes among national policies, including the need for data collection, increasing the capacity of domestic training programs, and the need to address geographic maldistribution of physicians. Ultimately, we aim to guide policy in the development of a re-silient and sustainable healthcare workforce capable of meeting diverse community needs and promoting equity in healthcare services.

This article discuss the effects of heat treatment and lubrication modes on the machinability of an A356 alloy (Al-Si-Mg); the alloy is studied as-received, with solution heat-treated alloy (SHT) as well as with an alloy that is solution heat-treated and then aged at 155, 180 and 220 °C. In the course of machinability evaluation, several criteria including cutting force, surface roughness, tool wears and burr analysis (chip) were studied. The results and analysis in this work indicated that the selected machinability criteria are important and necessary to effectively evaluate the machinability of A356 alloys. The machinability of both materials and tools were estimated in terms of cutting force, chip thickness ratio and burr formation, flank wear and roughness. The effects of different cutting parameters (cutting speed and feed rate) and lubrication modes (dry, mist and wet) on the machinability of the A356 cast alloy were also examined. The influence of heat treatments on the burr formation and surface quality was clearly revealed by the experimental results. Experimental work revealed that cutting forces were influenced significantly by aging and cutting speed. However, the different aging at 155, 180, and 220 °C and the cutting speed significantly affected the machinability of the A356 cast alloy. The results obtained show that a better drilling performance in terms of surface quality occurs at a high feed rate, with dry drilling and artificial aging at T6.

Modern organic synthesis is majorly focused on developing environmentally benign synthetic protocols by employing green chemistry principles. Accordingly, in our recent research work, we herein report the use of modified supramolecular host cyclodextrin as an effective solid based green catalyst for accessing structurally diverse and medicinally relevant pyrimidone architectures. The catalyst and the synthesized compounds 4 (a-r) were characterized using FT-IR, NMR and GC-Mass spectroscopy. Major highlights of the reported work include: atom economical process, extremely milder reaction conditions, operational simplicity, high isolated yields, and excellent catalyst turnover number. The molecular docking studies suggest that the compound 4n has the hydrogen bonding, hydrophobic and π-pair interactions with the active site of active sites of CXT M 15 receptor.

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

Introduction the outbreak of the Israel-Gaza conflict, initiated by a major attack on the civilian population in Israel provided a tragic opportunity to study the community wide association between severe emotional stressors related to acts of war and the incidence and clinical characteristics of Takotsubo cardiomyopathy (TCM) in this scenario. Methods Eight consecutive cases of TCM diagnosed during the first 50 days of the Israel-Gaza conflict were retrospectively collected from two southern medical centers who provided care to most of the war victims throughout the period of monitoring. The medical records were thoroughly reviewed and analyzed. Results During the monitoring period, the incidence of TCM increased substantially compared to the control period. Eight patients were included in the analysis. All patients were female and 100% of patients presented within the first 3 weeks of conflict whereas after this initial phase, despite the continuing war, the incidence of TCM reverted to pre-conflict levels. Two patients (25%) were under 50 years of age. All patients had hazardous clinical characteristics including severe left ventricular (LV) dysfunction (≤35%) and prolonged QTc interval (>500 ms). Five patients (62.5%) experienced complications. Nevertheless, no in-hospital mortality was reported. Conclusions Repeated exposure to severe emotional stress, on both personal and national level, due to mass crisis such as war is associated with an increased incidence of TCM potentially with high-risk phenotype in comparison to TCM following other, less potent, psychological insults.

The danger is still very large from cross site scripting attacks. When designing web applications We must follow as much as we can prevention rules and don’t leave any loophole to our programs. Experience is a great factor for programmers to know these attacks and for a trainee programmer is a difficult task to spot all the weak points. In this article we present a tutorial on launching an XSS attack and also we propose simple solutions.

In the Lemongrass (Cymbopogon citratus), the investigations showed a wide range of active molecules their biological properties. However, most of these studies were conducted on the wid varieties, while cultivated plan addressed. This study aimed to characterize the biomolecules and biological activities of Lemongrass growing us African conditions sons in in Marocco. Marocco. Phenolic compound profiles of aqueous (AE) E) ethanol ethanol (EE), (EE), and methanol (ME) extract: fractions were obtained with steric exclusion chromatography on Sephadex 050 gel and identified by LC-MS/MS polyphenols (TPC), flavonoids (TFC), and antioxidant activities (FRAP: scavenging value and TAC: Total Antioxidant C the fraction were evaluated as well as the antimicrobial activity Obtained results showed that the ME contained e compounds (ie. Apigenine-7-0-rutinoside and myricitine-3-0-rutinoside). The AE showed the presence of five mole kaemiferol-3-0-glucuronide), while EE showed the presence of three molecules (Le. Quercetine-3-0-rutinoside). Reg chemical characterization, the rization, e highest value of Total phenolic content (TPC) was obtained in conten btained in AE ΑΕ (25) (4.60-0.29 mg highest value of Total flavonoids content (TFC) was obtained Ined in ME (29) (0.7±0.08 mg/g). Concerning the antioxide the highest FRAP was obtained in ME (29) (97.89%) and the highest total antioxidant capacity (TAC) was obtained (89.89%) Correlation between FRAP, TPC, and TFC was noted poly in fractions of AE and ME. All tested extracts of and their fractions showed a significant antimicrobial effect. The lowest minimum inhibitory concentration (MIC) wa for ME against E. col. Extracts biological activities and their fractions were governed by their active molecules. Ther new and clarify a novel aspect of bioactive molecules in the extracts of cultivated C. citratus Equaly, throughout this we clarified the relationship between identified molecules and their biological properties including antioxidant and comparative studies new activities, which is new for the study area. This study is suggested to be a reference. assays of other biological activities for the study plant

Analytical instruments used for scientific research and education are often expensive. This limitation poses a challenge for schools and educators in low-income countries to provide practical science training to students. To address this problem, the improvisation of analytical instruments and instructional materials has emerged as a viable solution. By incorporating practical experiments into science education, students have the opportunity to engage directly with scientific instruments, conduct investigations, and collect data. This hands-on approach fosters a deeper understanding of scientific principles, enhances critical thinking skills, and cultivates scientific mindsets among students. Herein, we review and discuss, step-by-step, the approach of using a smartphone for quantitative analysis, referred to as smartphone digital image colorimetry (SDIC). SDIC, with its practicality and accessibility, utilizes smartphone digital cameras for image acquisition and the freely available image processing programs, such as ImageJ and smartphone Apps, for image quantification. Using SDIC can enable students in low-income countries to develop essential scientific skills, including critical thinking, data interpretation, and an evidence-based approach to scientific research. By leveraging the ubiquity and affordability of smartphone technology, SDIC offers an accessible and cost-effective approach to practical science education, bridging the gap between theory and practice in resource-constrained settings.

Carbon sequestration via carbon capture and storage (CCS) method is one of the most useful methods to lower the CO₂ emission in the atmosphere. Ethylenediamine (EDA) and triethylenetetramine (TETA) modified mesoporous carbon (MC) has been successfully prepared as CO₂ storage materials. The effect of various concentrations of EDA or TETA added to MC as well as activated carbon (AC) on their CO₂ adsorption capacity were investigated using high purity CO₂ as feed and titration method to quantitatively measure the amount of adsorbed CO₂. The results showed that within 60 min adsorption time, MCEDA49 gave the highest CO₂ capacity adsorption (19.68 mmol/g), followed by MC-TETA30 (11.241 mol/g). The improvement of CO₂ adsorption capacity at low TETA loadings proved that the four amine functional groups in TETA gave advantages to CO₂ adsorption. TETA functionalized MC has a potential to be used as CO₂ storage materials as it is used at low concentration. Therefore, it is more benign and friendly to the environment.

The adsorption of carbon dioxide on amino silanes-functionalized MCM-41 and SBA-15 materials is reported. The functionalization of mesoporous silicas was made by post-synthesis method, by impregnation of 3-aminopropyltriethoxysilane. The obtained materials were characterized by X-ray diffraction, scanning and transmission electron microscopies, nitrogen adsorption-desorption and X-ray photoelectron spectroscopy measurements. The carbon dioxide adsorption capacities for the samples were carried out under ambient pressures. The obtained results evidenced that amino-silanes with a terminal amine (–NH₂) were functionalized through covalent coupling of this group on the surface of the channels in the ordered mesoporous silica, meaning that the amine is anchored on the surface of the bigger pores of the MCM-41 and SBA-15 support. For functionalized materials, the CO₂ adsorption capacity of the AMCM-41 increased from 0.18 to 1.1 mmol·g⁻¹, whereas for ASBA-15, it was from 0.6 to 1.8 mmol·g⁻¹. The Lagergren kinetic algorithms were applied in order to validate the obtained results, evidencing the enhanced carbon dioxide adsorption capacity and stability of the functionalized ordered mesoporous molecular sieves.

The impacts of spice (sumac, cumin, black pepper, and red pepper) extract on Gram-positive (S. aureus and E. faecalis) and Gram-negative (K. pneumonia, P. aureginosa, C. jejuni, A. hydrophila, S. Paratyphi A, and Y. enterocolitica) food-borne pathogen bacterial strains (FBP) for their antibacterial activity and accumulation of ammonia (AMN), trimethylamine (TMA), and biogenic amines (BAs) in tyrosine decarboxylase broth (TDB) were investigated. Sumac extract exhibited the highest an-tibacterial potential against all FBP followed by cumin and peppers. Ammonia (AMN) production (844.24-543 mg/L) was strongly inhibited by sumac extract (55.10 mg/L), whilst suppression of trimethylamine (TMA) production (53.66-3.21 mg/L) was observed by sumac (1.28 mg/L), followed by red pepper (0.91 mg/L) extract. Cumin extracts stimulated the production of cadaverine, spermidine, tryptamine, and 2-phenylethylamine. Furthermore, sumac extracts inhibited hista-mine and tyramine production in the majority of FBP. This research suggests the application of sumac extracts as natural preservatives for inhibiting the growth of FBP and inhibiting the pro-duction of AMN, TMA, and BAs.

The classification of kidney tumors has undergone a remarkable evolution since the early 19th century, reflecting advances in medical science and technology. This historical overview traces the development of renal tumor classification, beginning with early clinical observations and macroscopic descriptions to the integration of molecular diagnostics in contemporary classifications. The establishment of international organizations like the World Health Organization (WHO) facilitated collaboration and standardization in tumor classification, leading to refined classifications and standardized nomenclature. Advancements in histological and molecular studies, particularly genetic analyses, revolutionized the understanding of renal cell carcinomas, enabling precise categorization based on molecular characteristics. The journey from rudimentary classifications to sophisticated systems based on detailed histological, immunohistochemical, and molecular criteria underscores the continuous evolution of kidney tumor classification. This article provides a comprehensive overview of this evolution, highlighting the contributions of scholars and the impact of technological advancements on our understanding and management of kidney tumors.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

Marketing is the manner of how to make our sales the best in the market, our prices the most accessible, our clients satisfactory, and thus our brand is the largest distributed. This needs sophisticated and advanced understanding of the total network related. Indeed, marketing data may be seen in different forms such as qualitative and quantitative. However, in the literature, it is easily noticed that large bibliography may be collected about qualitative studies, against few studies on the quantitative point of view. This is a major drawback that makes the marketing science still focusing on the design, although the market is strongly depending on quantities such as money and time. Indeed, marketing data may be a time series such as brand sales per specified periods, brand related-prices over specified periods, market shares, ..., etc. The purpose of the present work is to investigate some marketing models based on time series due to brands. We will precisely study the effect of the time scale on the persistence of brands sales in the market and on the forecasting of such a persistence according to the characteristics of the brand and the related market competition or competitors. Our study is acted on a sample of Saudi brands during the period November 22, 2017 to December 30, 2021.

In the present paper, we investigate the impact of the timescale factor on the quality of life index behavior on specific time intervals characterized by the presence of socio-economic, political, and/or health severe movements such as pandemics and crises. We essentially aim to show that effectively the quality of life measuring based on a single index in the existing studies may be described more adequately by a variable index due to the social, political, economic, and also healthy environment. The variability discovered is expressed by the existence and the estimation of a multi-index instead of a single one relatively to many factors. Our focus is mainly on the effect of the COVID-19 pandemic on the quality of life. Our model is applied empirically to a sample corresponding to Saudi Arabia as a case of study during the period from January 1990 to December 2021 as the main period affected by the COVID-19 pandemic. The sample is based on social media conversations and texts discussing and describing the satisfaction with the quality of life. The study confirms effectively that the role of the timescale factor is more described when considering a multi-index rather than measurement on the whole time interval.

In this contribution, the propylamine-functionalized cellulose (Cell-Pr-NH2) was employed as the catalyst in the three-component reaction between hydroxylamine hydrochloride, various type of aryl/heteroaryl aldehydes, ethyl acetoacetate/ethyl 4-chloroacetoacetate/ or ethyl 3-oxohexanoate. The results of these experiments were the formation of 3,4-disubstituted isoxazol-5(4H)-one heterocycles. The desired five-membered heterocyclic compounds were obtained in good to high yields at room temperature. The investigation of different solvents led us to the conclusion that water is the best solvent to perform the current one-pot, three-component reactions. Attempts to find the optimum catalyst loading clearly showed that 14 mg of Cell-Pr-NH2 seems to be sufficient to carry out the reactions. This method has highlighted some principles of green chemistry including less waste generation, atom economy, use of water as an environmentally friendly solvent, and energy saving. Purification without chromatographic methods, mild reaction conditions, simple work-up, low-cost reaction medium, saving time, and obtainable precursors are other notable features of this one-pot fashion.

The development of biosensors for target detection plays a crucial role in advancing various fields of bioscience. This work presents the development of a genosensor that exploits the colorimetric phenol-sulfuric acid sugar reaction for the detection of DNA, and RNA as specific targets, and DNA intercalator molecules. The biosensor combines simplicity and reliability to create a novel bio-assay for accurate and rapid analysis. A 96-well microplate based on polystyrene polymer was used as the platform for an unmodified capture DNA immobilization via a silanization process and with (3-Aminopropyl) triethoxysilane (APTES). After that, a hybridization step was carried out to catch the target molecule, followed by adding phenol and sulfuric acid to quantify the amount of DNA or RNA sugar backbone. This reaction generates a yellow-orange color on the wells measured at 490 nm that was proportional to the target concentration. Under the optimum conditions, a calibration curve was obtained for each target. The developed biosensor demonstrated high sensitivity, good selectivity, and linear response over a wide concentration range for DNA and RNA targets. Additionally, the biosensor was successfully employed for the detection of DNA intercalator agents that inhibit the hybridization of DNA complementary to the immobilized capture DNA. The developed biosensor offers a potential tool for sensitive and selective detection in various applications, including virus diagnosis, genetic analysis, pathogenic bacteria monitoring, and drug discovery.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

In this study, a monoethanolamine aerosol growth model was developed to investigate the aerosol growth factor. Interactions among the internal conditions in an absorber were considered in this aerosol model. Additionally, an experiment was conducted to measure aerosol particle size, for collecting in-house validation data. Sucrose was used as the aerosol nuclei instead of sulfuric acid to prevent the corrosion of equipment used in the experiment. Experimental results showed that the outlet aerosol sizes increased to the same size regardless of the sucrose concentrations. The aerosol growth model was validated using the in-house experimental data. The aerosol growth model efficiently predicted the aerosol size. For investigating aerosol growth effects, particle number concentration was determined to be the primary factor affecting aerosol growth and amine emissions. When the particle number concentration increased, the aerosol size decreased, whereas the MEA emission increased.

Nanopeening treatment was applied to the AISI 420 steel to decrease its sensitivity to the tribocorrosion damage. Microstructural investigation highlighted that the Nanopeening treatment led to a high plastic deformation and nanostructured surface layer with 110 µm depth. . In order to study the combined effect of corrosion and mechanical wear, tribocorrosion tests were performed on non–treated and nanopeened samples in boric acid and lithium hydroxide solution, considering both continuous and intermittent sliding. It was found that the AISI 420 steel is sensitive the synergism between mechanical friction and electrochemical corrosion with a domination of abrasive wear. Adhesive wear was also detected in the wear track. Indeed, the mechanical wear was pronounced under intermittent sliding because of hard wear debris generation from the repassivated layer during rotating time. The Nanopeening treatment led to enhance mechanical performance and corrosion properties. Such improvement could be explained by the high plastic deformation resulting in the nano-structuration of grains and increasing hardness of AISI 420 steel.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

water resources in Morocco have been severely influenced by climate change (CC) and pro-longed drought, particularly, in the pre-Saharan zone. The Tafilalet region faces increasing pres-sure due to high demographic growth, increased demand for water, excessive groundwater con-sumption, and investment in agriculture. Using the Water Evaluation and Planning System (WEAP), this study assessed land cover and elevation and created future scenarios using the Standard Precipitation Index (SPI) and Standard Groundwater Level Index (SGI) to monitor hy-droclimate drought conditions in the Ziz watershed from 1989 to 2022. Results show decreasing precipitation, particularly from 2010-2020, with the last four years being the most challenging (SPI<-2). SPI and SGI have a high correlation, suggesting precipitation impacts groundwater in-dicators. Future scenarios predict a high risk of CC, with a 30% decrease in annual precipitation accumulation by 2100 under the optimistic scenario SSP126. Minimum temperature is expected to increase by 1.08°C (SSP126) and 2.61°C (SSP585), and maximum temperature by 1.05°C (SSP126) and 2.93°C (SSP585). Keywords: Climate Change, Water Resources, SPI, SGI, WEAP, Ziz watershed, Drought

The field of Cooperative Intelligent Transport Systems and more specifically Pedestrians to Vehicles could be characterized as quite challenging, since there is a broad research area to be studied, with direct positive results to society. Pedestrians to Vehicles is a type of Cooperative Intelligent Transport System, within the group of Early Warning Collision/Safety System. In this article, we examine the research and applications carried out so far within the field of Pedestrians to Vehicles Cooperative Transport Systems by leveraging the information coming from Vulnerable Road Users’, smartphones. Moreover, an extensive literature review has been carried out in the fields of Vulnerable Road Users Outdoor Localisation via smartphones and Vulnerable Road Users Next Step/Movement Prediction, which are closely related to Pedestrian to Vehicle applications and research. We identify gaps that exist in these fields that could be improved/extended/enhanced or newly developed, while we address future research objectives and methodologies that could support the improvement/development of those identified gaps.

There is a growing body of evidence supporting the significant role of bacterial biofilms in the pathogenesis of various human diseases including cancer. Biofilms are polymicrobial communities enclosed within an extracellular matrix composed of polysaccharides, proteins, extracellular DNA, and lipids. This complex matrix provides protection against antibiotics and host immune responses, enabling the microorganisms to establish persistent infections. Moreover, biofilms induce anti-inflammatory responses and metabolic changes in the host, further facilitating their survival. Many of these changes are comparable to those observed in cancer cells. This review will cover recent research on the role of bacterial biofilms in carcinogenesis, especially in colorectal (CRC) and gastric cancers, emphasizing the shared physical and chemical characteristics of biofilms and cancer. This review will also discuss the interactions between bacteria and the tumor microenvironment, which can facilitate oncogene expression and cancer progression. This information will provide insight into developing new therapies to identify and treat biofilm-associated cancers, such as utilizing bacteria as delivery vectors, using bacteria to upregulate immune function, or more selectively targeting biofilms and cancer for their shared traits.

Fractal analysis of time series aims to extract the hidden or complex structures issued from the associated real data, such as scaling laws, non-stationary, dynamics, and so on. In the present work, the air quality index and its components are considered as time series owing fractal structures. To understand their underlying dynamics, wavelet multifractal approach is applied starting with a wavelet multifractal spectrum test to confirm the multifractality of the underlying data. Next, a new model is introduced improving the classical minmax one, provided with a statistical measure for the adequacy of the new model. The theoretical findings are applied to the north west Tabuk region of Saudi Arabia for environmental and climate data related to pollutants and factors involved in the estimation of the air quality index.

Policing duties may inherently be dangerous due to stab, blunt trauma and ballistic threats. The addition of individual light armour vests (ILAVs) has been suggested as a means to protect officers. However, the addition of the extra load of the ILAV may affect officer ability to conduct occupational tasks. The purpose of this study was to determine if wearing any of 3 different ILAVs (ILAV A, ILAV B, & ILAV C) affected occupational task performance when compared to that in normal station wear. A prospective, within-subjects repeated measures design was employed, using a counterbalanced randomization in which each ILAV was worn for an entire day while officers completed a variety of occupationally relevant tasks. These tasks included a victim drag, car exit and 5 meter sprint, step down and marksmanship task. Results showed that performance in each task did not vary between any of the ILAV or normal station wear conditions. There was less variability in the marksmanship task with ILAV B, however. The results suggest that none of the ILAVs used in this study were heavy enough to significantly affect task performance in the assessed tasks when compared to wearing normal station wear.

Three different fields intersect in search of an understanding of the point-of-origin of modern-age diseases: 1) D-amino acids and their role under stress conditions; 2) evolutionary origin of the mitochondrion organelle in the eukaryotic cell; and 3) gut microbiota and human healthHere it is first suggested that D-amino acids function as universal signaling agents, after having evolved as prokaryotic communication, part of an organic communication process that governs the basic activities of all the cells and coordinates cell action.Mitochondria (symbiotic prokaryotic organelles), are creative source of D-amino acids as signaling agents in the central nervous system and in the neuroendocrine systems.Amino acids racemases catalyzes the conversion between the L-enantiomers ( protein building blocks) into D-enantiomers (signaling agents).It is suggested that hectic modern life may affect human health by causing stress to the gut microbiota. These affected, gut microbiota then secrete D-amino acids that enter the blood stream, as signaling agents, causing communication errors in the central nervous system, and in the neuroendocrine systems due to excessive quantity of D-amino acids.Treating gut microbiota with inhibitors of amino acids racemases or finding D-amino acid scavengers may be used in developing novel therapeutic strategies for diseases related to the central nervous system and neuroendocrine systems caused by stressed gut microbiota.

In insects, Adipokinetic hormone is the primary hormone responsible for the mobilization of stored energy. While a growing body of evidence has solidified role of Adipokinetic hormone (AKH) in modulating the physiological and behavioral responses to metabolic stress, little is known about the upstream endocrine circuit that directly regulates AKH release. We evaluated the AKH-producing cell (APC) transcriptome to identify potential regulatory elements controlling APC activity, and found that a number of receptors show consistent expression levels, including all known dopamine receptors and the Pigment Dispersing Factor receptor (PDFR). We tested the consequences of targeted genetic knockdown and found that AKH expression of RNAi elements corresponding to each dopamine receptor caused a significant reduction in survival under starvation. In contrast, PDFR knockdown significantly extended lifespan under starvation whereas expression of a tethered PDF in APCs resulted in a significantly shorter lifespan. These manipulations caused various changes in locomotor activity under starvation. We used live-cell imaging to evaluate the acute effects of the ligands for these receptors on APC activation. Dopamine application led to a transient increase in intracellular calcium in a sugar-dependent manner. Furthermore, co-application of dopamine and ecdysone led to a complete loss of this response, suggesting that these two hormones act antagonistically. We also found that PDF application led to an increase in cAMP in APCs, and that this response was dependent on expression of the PDFR in APCs. Together these results suggest a complex circuit in which multiple hormones act on APCs to modulate metabolic state.

The synergistic features of a three-component, photoinitiating system (A/B/C) based on the measured data and proposed mechanism of Liu et al. are analyzed. The co-initiators/additives B and C have dual-functions of : (i) regeneration of photoinitiator A, and (ii) generation of extra radicals for enhanced conversion efficacy (CE). The synergistic effects led to higher CE for both free radical polymerization (FRP) and cationic polymerization (CP). The CE of FRP has 3 terms due to the direct (tyep-I) coupling of the triplet state of A with the monomer (M) and the coupling of the two radicals, R and R', with M. The CE of CP has a transient state proportional to the effective absorption constant (b), the light intensity (I) and initiator concentration (A0), but a steady state is independent of the light intensity (I). For the CE of FRP, the contribution from radical R had two cases: (i) linear dependence on T=bIA0, or (ii) nonlinear square root dependence T0.5. The synergistic effects led to higher conversion of FRP and CP, consistent with the measured results. The theoretically predicted new features include: (i) co-initiator [C] which always enhances both FRP and CP conversions, and (ii) co-initiator [B] which leads to more efficient FRP, but it also reduces CP.

Trace amines are a separate, independent group of biogenic amines, close in structure to classical monoamine neurotransmitters such as dopamine, serotonin and norepinephrine. G protein-coupled Trace Amine-Associated Receptors (TAAR) are mostly investigated for their involvement in the pathogenesis of neuropsychiatric disorders, but expression of TAAR family receptors is observed also in various populations of cells of the immune system. The review is focused on the basic information on the interaction of trace amines and their receptors with cells of the general immune system of humans and other mammals, as well as on data on TAARs role in the function of individual populations of myeloid and lymphoid cells. With further research on the regulatory role of the trace amine system in the pathogenesis of the immune response and determination of the biological mechanisms for their action it would be possible to develop new methods for treating diseases related to immune system dysfunctions.

E-commerce is a rapidly evolving global trend that is having a significant impact on consumer behavior and business strategies. Despite its growing impact, e-commerce adoption by Moroccan firms remains low and research on this topic in this context is scarce. This study aims to fill this gap by investigating the main determinants influencing e-commerce adoption by Moroccan firms. We use logit, probit, and conditional mixed process-probit models to identify the critical factors driving e-commerce adoption. Our results reveal five key findings. First, newer firms that are more open to innovation and change are more likely to adopt e-commerce. Second, firms with a higher proportion of highly educated employees are more likely to adopt e-commerce. Third, the digital skills of new employees do not directly influence the likelihood of e-commerce adoption. Fourth, being listed on digital platforms increases the likelihood of e-commerce adoption. Finally, there is a positive relationship between firms engaged in innovation activities and e-commerce adoption. These findings highlight the need for additional investment in promoting modern organizational practices, reskilling workers, and implementing advanced technologies to facilitate effective e-commerce integration among Moroccan SMEs. By addressing these challenges, Moroccan firms can harness the full potential of e-commerce and contribute to the country’s economic growth and digital transformation.

Dictionary Learning (DL) and Sparse Representation (SR) based Classifier have impacted greatly on the classification performance and has had good recognition rate on image data. In Video Semantic Analysis (VSA), the local structure of video data contains more vital discriminative information needed for classification. However, this has not been fully exploited by the current DL based approaches. Besides, similar coding findings are not being realized from video features with the same video category. Based on the issues stated afore, a novel learning algorithm, called Sparsity based Locality-Sensitive Discriminative Dictionary Learning(SLSDDL) for VSA is proposed in this paper. In the proposed algorithm, a discriminant loss function for the category based on sparse coding of the sparse coefficients is introduced into structure of Locality-Sensitive Dictionary Learning (LSDL) algorithm. Finally, the sparse coefficients for the testing video feature sample are solved by the optimized method of SLSDDL and the classification result for video semantic is obtained by minimizing the error between the original and reconstructed samples. The experiment results show that, the proposed SLSDDL significantly improves the performance of video semantic detection compared with the comparative state-of-the-art approaches. Moreover, the robustness to various diverse environments in video is also demonstrated, which proves the universality of the novel approach.

In response to growing industrial demands, necessitated by larger ships and increased cargo volumes, many port authorities worldwide are undertaking a significant expansion of their infrastructure to increase their capacity. Significant expansion raises challenges such as potential congestion and environmental concerns, especially for port located in urban area as the case study explored in this paper. To address these issues, the study employs a combination of scenario analysis developed in collaboration with the port authority and logistic system simulation. This approach assesses the capacity of existing access gates to handle the increased trucking traffic and optimizes the unloading process of construction trucks at a new terminal. Key findings suggest that while the current gate capacities are adequate, optimizing unloading times at the new terminal is critical to prevent road congestion in urban area before the gate and reduce negative impacts such as sound and atmospheric pollution. The study advocates for an appointment system during peak hours to manage traffic flow effectively and underscores the importance of collaboration between the city and port authorities in managing truck traffic to mitigate congestion on the city side. Nonetheless, the study recognizes certain constraints, including the incomplete evaluation of the influence of intermodal transport on truck traffic. Furthermore, the study emphasizes the need for future research to consider the correlation between vehicle numbers and service levels, aiming to effectively adjust the time in the system.

Background: Respiratory syncytial virus (RSV) is a significant cause of illness in adults, especially older adults and those with underlying conditions. This study aimed to assess the incidence of RSV hospitalizations in adults and identify risk factors for hospitalization and poor outcomes. Methods: A retrospective cohort study was conducted using data from two hospitals in southern Israel from 2016-2022. We calculated incidence rates of RSV and influenza hospitalizations. Risk factors for hospitalization were analyzed using Poisson regression. We evaluated poor outcomes (death, ICU admission, or mechanical ventilation) among RSV-hospitalized patients. Results: The median annual incidence of RSV hospitalization was 28.2/100,000 population, increasing with age to 199/100,000 in those ≥75 years. Significant risk factors for RSV hospitalization included pulmonary diseases (RR 4.2, 95% CI 3.4-5.2), cardiovascular diseases (RR 3.3, 95% CI 2.6-4.2), and chronic renal failure (RR 2.9, 95% CI 2.3-3.7). Among hospitalized RSV patients, 13.9% had poor outcomes. Renal failure (RR 1.81, 95% CI 1.23-2.66), neutropenia (RR 2.53, 95% CI 1.19-5.35), neutrophilia (RR 1.66, 95% CI 1.81-2.34), and lymphopenia (RR 2.03, 95% CI 1.37-3.0) were associated with poor outcomes. Conclusions: RSV causes a substantial burden of hospitalizations in adults, particularly among older adults and those with comorbidities. Identifying high-risk groups can help target prevention and treatment strategies, including vaccination.

In the realm of the Internet of Things (IoT), a network of sensors and actuators collaborates to fulfill specific tasks. As the demand for IoT networks continues to rise, it becomes crucial to ensure the stability of this technology and adapt it for further expansion. Through an analysis of related works including Feedback-based Optimized Fuzzy Scheduling Approach (FOFSA) algorithm, Adaptive Task Allocation Technique (ATAT) and Osmosis Load Balancing algorithm (OLB), we identify their limitations in achieving optimal energy efficiency and fast decision-making. To address these limitations, this research introduces a novel approach to enhance the processing time and energy efficiency of IoT networks. The proposed approach achieves this by efficiently allocating IoT data resources in the Mist layer during the early stages. We apply the approach to our proposed system known as the Mist-based Fuzzy Healthcare System (MFHS) that demonstrates promising potential to overcome the existing challenges and pave the way for efficient Industrial Internet of Healthcare Things (IIoHT) of the future.

3D printing is commonly used to create complex objects at a low cost. It has also been applied in the fabrication of metamaterials and metasurfaces, which alter the propagation path of electromagnetic waves. These structures have diverse applications, including enhancing beam direction, improving antenna gain and signal-to-noise ratio, and creating filters and reflectors. Metasurfaces are cheap to fabricate and their use is expected to boost antenna efficiency in 5G telecommunications and beyond. However, accurately characterizing their profile remains a significant challenge. This paper presents a low-cost fully automated 4-axis instrument for microwave metasurface charac-terization, overcoming limitations of manual methods and offering an efficient and accurate approach. This research represents a significant advancement in microwave metasurface characterization, enabling sophisticated techniques to advance wireless communication technolo-gies, as it is the case of the future 5G and millimeter-wave communication systems. The equipment has an approximate cost of $1550 USD and was able to characterize a metalens with a focal distance of 20 cm designed for signals at 30 GHz. It was possible to create 2D and 3D profiles of the intensity distribution focused by the metalens and extract parameters such as the gain (8.05 dB), 3dB depth of focus (11 cm) and full width at half maximum (2.17 cm). The comparison of the measurements with the diffraction calculations of the metalens showed a very good agreement between the in-tensity distributions and the parameters of the metalens.

Copper (Cu) is a critical element for cancer cell proliferation and considerably accumulates in the nucleus. 64Cu2+ is an anticancer radiopharmaceuticals targeting the copper requirement of cancer cells. However, intravenously injected 64Cu2+ ions primarily accumulate in the liver. Ligand complexation of 64Cu2+ would be a promising method for increasing tumor delivery by reducing liver uptake. Herein, we used three tripodal amine ligands [tris(2-aminoethyl)amine (Tren), diethylenetriamine (Dien), and tris(2-pyridylmethyl)amine (TPMA)] to enclose 64Cu2+ ions and compared their in vivo tumor and liver uptake using a tumor-bearing xenograft mouse model of the extrahepatic bile duct carcinoma cell line TFK-1. We examined intracellular Cu distribution using microparticle-induced X-ray emission (micro-PIXE) analysis for these compounds. 64Cu2+-Tren and 64Cu2+-Dien showed higher tumor uptake than 64Cu2+-TPMA and 64Cu2+ ions in TFK-1 tumors. Among the three 64Cu2+ complexes and 64Cu2+ ions, liver uptake was inversely correlated with tumor uptake. Micro-PIXE analysis showed that in vitro cellular uptake was similar to in vivo tumor uptake and nuclear delivery was the highest for 64Cu2+-Tren. Conclusively, an inverse correlation between tumor and liver uptake was observed using three 64Cu2+ complexes of tripodal amine ligands and 64Cu2+ ions. These results provide useful information for the future development of anticancer 64Cu radiopharmaceuticals.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Several stochastic H∞ filters for estimating the attitude of a rigid body from line-of-sight measurements and rate gyro readings are developed. The measurements are corrupted by white noise with unknown variances. Our approach consists of estimating the quaternion while attenuating the transmission gain from the unknown variances and initial errors to the current estimation error. The time-varying H∞ gains are computed through differential and algebraic linear matrix inequalities whose parameters are independent of the state. The case of a gyro drift is addressed, too. Extensive Monte Carlo simulations show that the proposed stochastic H∞ quaternion filters perform well for a wide range of noise variances. The actual attenuation, which improves with the noise level and is worst in the noise-free case, is better than the guaranteed attenuation by one order of magnitude. The proposed stochastic H∞ filter produces smaller biases than a standard quaternion Kalman filter and similar standard deviations at large noise levels. An essential advantage of this H∞ filter is that the gains are independent of the quaternion, which makes it insensitive to modeling errors. This desired feature is illustrated by comparing its performances against those of unmatched Kalman filters. When provided with too high or too low noise variances the Kalman filter is outperformed by the $H_\infty$ filter, which essentially delivers identical error magnitudes.

Head and neck squamous cell carcinoma (HNSCC) is a highly heterogeneous and the most common form of head and neck cancer, posing significant challenges for disease management. Single-cell RNA sequencing (sc-RNAseq) has emerged as a valuable tool for addressing these challenges by enabling detailed characterization of the tumor microenvironment (TME) at the cellular level. This review assesses the utility of sc-RNAseq in HNSCC research, compiling current strategies employing single-cell technologies. For HNSCC etiology, sc-RNAseq allows for the construction of cellular atlases, characterization of different cell types, and investigation of key genes and processes involved in cancer initiation, development, and progression within the TME. In terms of HNSCC diagnosis and prognosis, the high resolution offered by sc-RNAseq enables the identification of cell type-specific signatures, enhancing prognostic models and disease stratifiers for more accurate patient outcome assessments. Regarding HNSCC treatment, sc-RNAseq provides insights into cellular responses to various treatments, including radiotherapy, chemotherapy, and immunotherapy, contributing to improved patient stratification and personalized treatment strategies. This review highlights the unique contributions of sc-RNAseq to HNSCC research, addressing its cellular and biological complexity, and emphasizes its potential for advancing research and clinical practice in other cancer types.

Trace amine-associated receptors (TAARs) are a family of G protein-coupled receptors present in mammals in the brain and in several peripheral organs. Apart from its olfactory role, TAAR5 is expressed in the major limbic brain areas and regulates brain serotonin functions and emotional behaviors. However, most of its functions remain undiscovered. Given the role of serotonin and limbic regions in some aspects of cognition, we used a temporal decision-making task to unveil a possible role of TAAR5 in cognitive processes. We found that TAAR5 knock-out (KO) mice showed a generally better performance due to a reduced number of errors and displayed a greater rate of improvement at the task than WT littermates. However, task-related parameters, such as time accuracy and uncertainty have not changed significantly. Overall, we show that TAAR5 modulates specific domains of cognition, highlighting a new role in brain physiology.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

This scoping review comprehensively explores the existing literature on fenugreek (Trigonella foenum-graecum), a versatile herb known for its culinary and traditional medicinal uses. The review focuses on two key aspects: the hypoglycemic mechanism of fenugreek and its impact on milk production in breastfeeding women. By systematically analyzing and synthesizing the available evidence, this review aims to enhance our understanding of fenugreek's potential applications and identify research gaps for future systematic reviews. The search strategy targeted English-language animal studies published within the last five years that specifically investigated fenugreek's hypoglycemic mechanism and its effects on milk production. A total of 15,236 articles were initially identified from databases such as PubMed, Sci finder and ScienceDirect. After a rigorous selection process, including thorough evaluation of titles, abstracts, and full-texts, a subset of articles (including those titled "Impact of Fenugreek on Milk Production in Rodent Models of Lactation Challenge" and "Fenugreek Stimulates the Expression of Genes Involved in Milk Synthesis and Milk Flow through Modulation of Insulin/GH/IGF-1 Axis and Oxytocin Secretion") were included for detailed analysis. The findings 18 articles from the included studies demonstrate promising results regarding fenugreek's potential to stimulate milk production and regulate blood glucose levels. However, further research is necessary to unravel the underlying molecular pathways, establish optimal dosage guidelines, and assess long-term side effects. Overall, this scoping review offers valuable insights for lactating women seeking to enhance milk production and individuals managing blood sugar levels, providing potential alternative approaches for supporting lactation and glycemic control.

Modern engineering faces challenges in ensuring technical standards for service, durability, and sustainability. Political, administrative, and budgetary factors, coupled with climate change, pose tasks to structural integrity, affecting industries and economies. Marine infrastructures represent a strategic asset of the country as it handles a large part of the economic exchanges. This article analyzes five essential factors that play a fundamental role in the performance analysis of coastal structures: Chloride-induced corrosion, degradation models, maintenance strategies, monitoring, and climate change. Starting with reinforcement corrosion, considered as the main cause of distress, particularly in coastal zones for the long-term behavior of structures. Additional pressure from the influences of climate change is becoming evident and extreme, leading to reduction in capacity. To guarantee the lifespan, degradation models contribute by estimating the long-term performance of the asset as a strategic piece to the development of effective maintenance solutions. Additionally, quantifying the condition of the structure from monitoring data, plays a crucial part that provides information on the current situation of the structure. Finally, this review summarizes the challenges associated with the maintenance of aging marine structures considering aspects such as corrosion, monitoring, and the future challenges this area will face due to climate change.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

Climate data are important in building a hydrological risk assessment model. The ClimInonda web application enables interactive and dynamic visualizations of different data collected from different weather stations in the study area on a single platform, allowing users to explore and analyze data in an easy way. This can assist decision-makers and stakeholders in understanding the current state of the environment and in identifying areas of flooding risk. Visualizations can include different types of data, such as satellite imagery, weather data, and terrain data, and can be displayed using various techniques, such as heat maps, contour maps, and 3D models by providing easy-to-understand visualizations. The different stations of the Gafsa and Kasserine governorates in the study area are included and other stations of the Algerian territory (Tebessa governorate) are incorporated. This web application also provides the capability to include each user's stations.

A possible way to valorize citrus peels, which are byproducts of the juice extraction industry, is to use them as natural biopreservatives. In this paper we present early results from a compared Solvent Free Microwave Extraction (SFME) with Hydro-Distillation (HD) and Cold Pressing (CP) of essential oils (EOs) using fresh orange peel (Citrus sinensis L. var. Valencia late), a by-product in the production of orange juice in Algeria. The EOs were analyzed by gas chromatography coupled to mass spectrometry (GC-MS). All extracted C. sinensis EOs were chemotype limonene (94.64 to 95.48%). SFME is performed without added any solvent or water. SFME increases EO yield and eliminate wastewater treatment, resulting in a great progress in terms of time and cost efficiency. In its second part, the present study was conducted to evaluate “in vitro”, the antioxidant activities of Solvent Free Microwave (SFM) extracted orange EO by using the DPPH• (2,2-di-phenyl-1-picrilhydrazyl) free radical scavenging assay. The ability of orange EO to scavenge the free radical DPPH• was high, exceeding 80%. The result of the DPPH assay gives an IC₅₀ range value of 89.25 μg/mL (0.09 mg/mL) for the studied sample. Accordingly to the scientific literature, C. sinensis EO tested in the present study presented strong antioxidant activity, when looking to its values of AAI = 1.12 μg/mL. The feasibility of biopreservation used EOs as an alternative to synthetic techniques for liquid whole egg (LWE) stored under commercial retail conditions was investigated. The orange EO extracted by SFM was screened for its antibacterial and antioxidant activities in LWE at concentrations of 0.1, 0.3 and 0.5%. The TBA-RS results showed that the EO treatments significantly (p < 0.05) reduced the lipid oxidation in LWE. The long term oxidative, microbial and organoleptical stability of the LWE during display was positively influenced by orange EO treatments. Therefore, the results obtained here confirm that EO treatment as a promising technology to extend the commercial shelf-life of liquid egg products during retail/display.

Soil erosion seriously affects vineyards. In this study, the influence of two plant covers on soil moisture and the effect of different physiographic conditions on runoff and sediment yields were evaluated in a rainfed vineyard formed by four fields (NE Spain) during 15 months. One field had spontaneous vegetation as plant cover and three fields had a cover crop of common sainfoin. The vineyards’ rows were dry and stable, whereas the inter-row areas were wet although very variable, and the corridors were wet and very stable. Soil moisture in the inter-row areas with Common sainfoin was much higher than in the rows (62% - 70%) whereas this difference was lower with spontaneous vegetation (40%). Two runoff and sediment traps (STs) were installed in two ephemeral gullies, and 26 time-integrated surveys (TIS) done. The mean and maximum runoff yields were 9.8 and 30.7 l TIS^–1 in ST2 and 13.5 and 30.2 l TIS^–1 in ST3. The mean turbidity was 333 and 19 g l^–1, and the maximum sediment yields were 41,260 and 2,778 g TIS^–1 in ST2 and ST3. Changes in the canopy covers (grapevines and plant covers) and rainfall parameters explained the runoff and sediment dynamics.

All living cells maintain a charge distribution across their cell membrane (membrane potential) by carefully controlled ion fluxes. These bioelectric signals regulate cell behavior (such as migration, proliferation, differentiation) as well as higher-level tissue and organ patterning. Thus, voltage gradients represent an important parameter for diagnostics as well as a promising target for therapeutic interventions in birth defects, injury, and cancer. However, despite much progress in cell and molecular biology, little is known about bioelectric states in human stem cells. Here, we present simple methods to simultaneously track ion dynamics, membrane voltage, cell morphology, and cell activity (pH and ROS), using fluorescent reporter dyes in living human neurons derived from induced neural stem cells (hiNSC). We developed and tested functional protocols for manipulating ion fluxes, membrane potential, and cell activity, and tracking neural responses to wounding and re-innervation in vitro. Finally, using morphology sensor, we tested and quantified the ability of physiological actuators (neurotransmitters and pH) to manipulate nerve wound re-innervation. These methods are not specific to a particular cell type and should be broadly applicable to the study of bioelectrical controls across a wide range of combinations of models and endpoints.

Background: The genetic variants identified by three large genome-wide association studies (GWAS) of educational attainment were used to test a polygenic selection model. Methods: Average frequencies of alleles with positive effect (polygenic scores or PS) were compared across populations (N=26) using data from 1000 Genomes. A null model was created using frequencies of random SNPs. Results: Polygenic selection signal of educational attainment GWAS hits is high among a handful of SNPs within genomic regions replicated across GWAS publications. A polygenic score comprising 9 SNPs predicts population IQ (r=0.88), outperforming 99% of the polygenic scores obtained from sets of random SNPs (Monte Carlo p= 0.011). Its predictive power remains unaffected after controlling for spatial autocorrelation (Beta= 0.83). The largest polygenic score (161 SNPs) exhibits similar predictive power (Beta=0.8). Random polygenic scores are moderate predictors of population IQ (thanks to spatial autocorrelation), and their predictive power increases logarithmically with the number of SNPs, indicating an exponential reduction in noise. Conclusion: This study provides guidance for using GWAS hits together with random SNPs for testing polygenic selection using Monte Carlo simulations.

Streptococcus mutans is a key bacterium in dental caries- one of the most prevalent chronic infectious diseases. Conventional treatment both fails to specifically target the pathogenic bacteria and at-tempts to eradicate commensal bacteria as well. Thus, caries remains one of most common and challenging diseases. The use of bacterial viruses as anti-bacterial agents, is gaining interest worldwide. Hardly any phages were described against S. mutans. The objective of this study was to isolate anti-S. mutans phages and to characterize their antimi-crobial properties. Human saliva samples were filtered and screened for potential phages. Standard double-layered agar method was used for isolation. Whole genome sequence analysis and morphology visualization by TEM, were used for anti-S. mutans phage identification. Antibacterial properties were evaluated using clinical strains and ATCC strains of S. mutans in various states. Antibacterial effect was also tested on human cariogenic dentin. One phage against S. mutans was isolated and termed SMHBZ8. This phage showed effective lytic activity in vitro against both planktonic and biofilm S. mutans cultures. Moreover, the phage showed antibacterial effect when used on cariogenic dentin. The isolation and characterization of SMHBZ8 may be the first step in developing a potential phage therapy for dental caries.

Polymer electrolyte was used as a medium for testing the performance of microband electrodes under conditions of linear diffusion. Cyclic voltammetry and chronoamperometry experiments were performed in such viscous medium, where diffusion rates are much slower than in fluid solutions. Confirmation of the existence of such conditions from the log i vs. log v or log i vs. log t relationships in the current equation always yielded values lower than the expected value of 0.5. This could indicate impure linear diffusion profile, i. e. some contribution from radial diffusion (edge effect). However, performing these tests in monomeric solvents of similar viscosities, such as glycerol or propylene glycol, gave the desired value of 0.5. These results lead to the conclusion that current equations which are based on Fick’s laws may not be applicable for polymer electrolytes, where various obstruction to diffusion make it a more complicated process than in monomeric solvents.

This paper presents a novel method for automatic modulation classification (AMC) for cognitive radio (CR) networks based on a simple classifier that is trained with high-order cumulant. The proposed method focuses on the statistical behavior of modulated signals and includes analog modulation and digital schemes, which received less attention in the literature. The effectiveness of the proposed method is demonstrated through simulation results using high-quality generated signals under different signal-to-noise ratios (SNRs) and channel conditions. The classification performance achieved by the proposed method is superior to that of the more complex deep learning methods, making it well-suited for deployment in end units of CR networks, particularly in military and emergency service applications. The proposed method offers a cost-effective, high-quality solution for AMC that meets the stringent requirements of these critical applications.

Recently we have seen a relaxation of the historic restrictions on the use and subsequent research on the Cannabis plants, generally classified as Cannabis sativa and Cannabis indica. What research has been performed to date has centered on chemical analysis of plant flower products, namely cannabinoids and various terpenes that directly contribute to phenotypic characteristics of the female flowers. In addition, we have seen many groups recently completing genetic profiles of various plants of commercial value. To date, no comprehensive attempt has been made to profile the proteomes of these plants. We report herein our progress on constructing a comprehensive draft map of the Cannabis proteome. To date we have identified over 17,000 potential protein sequences. Unfortunately, no annotated genome of Cannabis plants currently exists. We present a method by which “next generation” DNA sequencing output and shotgun proteomics data can be combined to produce annotated FASTA files, bypassing the need for annotated genetic information altogether in traditional proteomics workflows. The resulting material represents the first comprehensive annotated protein FASTA for any Cannabis plant. Using this annotated database as reference we can refine our protein identifications, resulting in the confident identification of 13,000 proteins with putative function. Furthermore, we demonstrate that post-translational modifications play an important role in the proteomes of Cannabis flower, particularly lysine acetylation and protein glycosylation. To facilitate the evolution of analytical investigations into these plant materials, we have created a portal to host resources we have developed from proteomic and metabolomic analysis of Cannabis plant material as well as our results integrating these resources. All data for this project is available to view or download at www.CannabisDraftMap.Org

Several factors influence traffic congestion and overall traffic dynamics. Simulation modeling has been utilized to understand the traffic performance parameters during traffic congestions. This paper focuses on driver behavior of route selection by differentiating three distinguishable decisions, which are shortest distance routing, shortest time routing and less crowded road routing. This research generated 864 different scenarios to capture various traffic dynamics under collective driving behavior of route selection. Factors such as vehicle arrival rate, behaviors at system boundary and traffic light phasing were considered. The simulation results revealed that shortest time routing scenario offered the best solution considering all forms of interactions among the factors. Overall, this routing behavior reduces traffic wait time and total time (by 69.5% and 65.72%) compared to shortest distance routing.

The synthesis of the presented benzo[d]thiazol-2-amine derivatives was performed by condensing-(4-chlorobenzylidene) benzo[d]thiazol-2-amine with a number of substituted phenols in the presence of potassium iodide and anhydrous potassium carbonate in dry acetone. IR spectroscopy, 1HNMRspectroscopy and spectroscopy methods were used to characterize the structural properties of newly synthesized derivatives. In order to observe the attributes of drug-like candidates of these derivatives, the number of their molecular properties was estimated. Benzo[d]thiazol-2-amine derivatives were molecularly docked with selective enzymes COX-1 and COX-2. Findings suggested that Compounds G3, G4, G6, G8 and G11 possess higher binding affinity than diclofenac sodium, when docking was performed with enzyme COX-1. Compounds G1, G3, G6, G8and G10 showed lower binding affinity than Indomethacin when docking performed with enzyme COX-2.In vitro evaluation of the COX-1 and COX-2 enzyme inhibitory activities were performed for synthesized compounds. Compounds 10 and 11 exhibited significant COX-1 and COX- enzyme inhibitory action with IC50 values of 5.0 and 10 µM, respectively. Using the hot plate method and the carrageenan-induced rat paw edema model, the synthesized compounds were screened for their biological activities, including analgesic and anti-inflammatory activities. The highest analgesic action was exhibited by derivative G11and the compound G10 showed the highest anti-inflammatory response.

The rapid expansion of livestock production sector to meet the world population demand is posing a big challenge to environmental sustainability. Plant-based feed additives extracted from food by-products could potentially result in a double outcome: improving animal zootechnical performances and mitigating environmental impacts of meat production chains. This presented study was carried out to assess the environmental impacts of the supplementation of a commercial Citrus extract feed additive (CEFA) in swine and broiler farming. Life cycle assessment (LCA) was applied to assess the impact of manufacturing and distributing 1 bag of 25 kg of CEFA and its use in feed in broiler and swine productions. With regard to CEFA manufacturing and distribution, results showed that the majority of impact came from the production of CEFA ingredients, accounting for 70% impact generated. The remaining 30% effect was divided to transportation to customer (25%), CEFA packaging (3%), CEFA manufacture, and production loss (2%). When enlarging the scope, the use of CEFA in piglet and broiler diets showed improving the measured environmental indicators, compared to such standard systems. Indeed, feed supplemented CEFA have demonstrated in elevating zootechnical performances, hence saving feed consumed. Consequently, that helped reduce environmental issues from animal feed ingredients’ agriculture. To be more specific, the supplementation of 25 kg of CEFA in feed led to a reduction of 6 tons of CO2 emitted along the life cycle of broiler production and 5 tons in the case of fattening pig. 0.7 hectares of land used had been saved as well as, 201 m3 of water (broiler) and 82 m3 (swine) were economized. Environmental performance assessment showed the interest in using this CEFA in swine and broiler diets to mitigate the environmental impacts.

Mercury (Hg (II)) contamination is indefatigable global hazard which causes severe permanent damages to human health. Extensive research has been carried out to produce mercury adsorbents however they are still facing certain challenges limiting their upscaling. Herein we reported the synthesis of novel amine impregnated inverse vulcanized copolymer for effective mercury removal. Poly(S-MA) was prepared using sulfur and methacrylic acid employing inverse vulcanization method following by functionalization. The polyethylenime (PEI) was impregnated on poly(S-MA) to increase the adsorption active sites. The developed adsorbent was then characterized using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR confirmed formation of copolymer and successful impregnation of PEI and SEM revealed composite porous morphology of the copolymer. Amine impregnated copolymer (amine@poly(S-MA)) outperformed poly(S-MA) in mercury as it showed 20 % superior performance with 44.7 mg/g maximum adsorption capacity. The adsorption data best fits the pseudo second order which indicates that the chemisorption is most influential mechanism in this case indicating the involvement of NH2 in mercury removal. The adsorption is mainly monolayer on homogenous surface as indicated by 0.76 value of Redlich-Peterson exponent (g) which describes the adsorption nature advent from R2 value of 0.99.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

A two scalar field model that incorporates non Riemannian Measures of integration or usually called Two Measures Theory (TMT) is introduced, in order to unify the early and present universe. In the Einstein frame, a K-essence is generated and as a consequence for the early universe, we can have an Inflation for the very early universe and then, after inflation, an early dark energy period and a late dark energy period for the present universe dark, both dark energy epochs have a consistent generation of dark energy (DE), dark matter (DM) and stiff matter. This is obtained when the scale invariance is introduced and then is spontaneously broken from the integration of the degrees of freedom associated with the modified measures. The resulting effective potentials and K-essence in the Einstein frame produce the three flat regions corresponding to the different epochs mentioned before. For the first flat region, we can associate an inflationary universe. Also assuming this first plateau, we study the inflation in the framework of the slow-roll approximation. In this scenario under the slow roll approximation, we obtain a linear combination that is a constant. The corresponding cosmological perturbations in our model are determined and we also obtain the different constraints on the parameter-space from the Planck data. The slow roll approximation can be arranged so that the transition from inflation to the next flat region can be achieved without problems. In the following two flat regions, in addition to the inflation phase, representing the Early Dark Energy and Late Dark Energy Periods, with DE and also the DM, do not need to be introduced separately, they are instead a result of a K-essence induced by the multi measures, multi field theory. Therefore the scalars generate both the DE and the DM . Also a stiff matter component is automatically generated from the K-essence theory from two scalar fields. From the perturbative analysis associated to the perturbation solution of background, we find a correlation between the two scalars. Besides, we obtain that our model during the dark epoch has a behaviour of tracking freezing mode

The realization of a BRST cohomology of the 4D topological gauge-affine gravity is established in terms of a superconnection formalism. Identification of fields in the quantized theory is occurred directly as usual in terms of superconnection and its supercurvature components with the double covering of the general affine group GA¯(4,R). Then, by means of an appropriate decomposition of the metalinear double-covering group SL¯(5,R) with respect to the general linear double-covering group GL¯(4,R) one can easily obtain the enlargements of the fields while remaining consistent with the BRST algebra. This leads to the descent equations allowing us to build the observables of the theory by means of the BRST algebra constructed using a sa¯(5,R) algebra-valued superconnection. In particular, we discuss the construction of topological invariants with torsion.

Newcastle Disease (ND) remains a critical disease affecting poultry in sub-Saharan Africa. In some countries, repeated outbreaks have a major impact on local economies and food security. Recently, we developed an adenovirus-vectored vaccine encoding the Fusion protein from an Ethiopian isolate of Newcastle Disease Virus (NDV). The adenoviral vector was designed and a manufacturing process developed in the context of the Livestock Vaccine Innovation Fund initia-tive funded by the International Development Research Centre (IDRC) of Canada. The industrial-ly-relevant recombinant vaccine technology platform is being transferred to the National Veteri-nary Institute (Ethiopia) for veterinary applications. Here, we demonstrate that the instillation of the adenoviral vector through the nasal cavity can confer protection to chickens against a lethal challenge with NDV. A manufacturing process using HEK293 suspension cells cultured in stirred-tank bioreactor for the vaccine production is proposed. Taking into consideration supply chain limitations, options for serum-free media selection have been evaluated. A streamlined downstream process including a filtration, an ultrafiltration and a concentration step was de-veloped. With high volumetric yields (infectious titers up to 5 x 109 TCID50/mL) in the culture su-pernatant, the final formulations were prepared at 1010 TCID50/mL, either in liquid or lyophi-lized forms. The liquid formulation was suitable and safe for mucosal vaccination and was sta-ble for 1 week at 37˚C. Both liquid and lyophilized formulations were stable after 6 months of storage at 4˚C. Overall, a manufacturing process for adenovirus vectored vaccine was developed and protective doses were determined using a convenient route of delivery. Formulation and storage conditions were established, and quality control protocols were implemented.

Sulfated polysaccharides from seaweed are highly active natural substances having valuable applications. In the present paper, attempts have been made to discuss the physicochemical and structural features of polysaccharides isolated from red marine alga Alsidium corallinum (ACPs) and its protective effect in hepatic impairments induced by tebuconazole (TBZ) in rats. Structural features were determined using High performance liquid chromatography, Fourier transformed infrared, and solid state ¹H and ¹³C-Nuclear magnetic resonance analysis. ACPs are found to be hetero-sulfated-anionic polysaccharides that contained carbohydrates, sulfate groups and uronic acids. In vitro biological activities suggested the effective antioxidant and antimicrobial capacities of ACPs. For antioxidant testing in vivo, the biochemical analysis and plasma profiles displayed that oral administration of ACPs could mitigate blood lipid indicators, including total cholesterol, triglyceride, low and high density lipoprotein cholesterol, bilirubin, liver function indexes involving alanine aminotransferase and aspartate aminotransferase, showed that ACPs possessed obvious antioxidant activities. Besides, the intervention of ACPs potentially inhibited lipid peroxidation, protein oxidation, key enzymes of lipid metabolism (<0.001) and increased levels and antioxidant status (<0.05). Histomorphological observation confirmed that ACPs intervention could partially repair liver injuries caused by TBZ. The computational results showed that A. corallinum monosaccharides bound 1JIJ, 1HD2 and 1WL4 receptors with acceptable affinities, which together with deep embedding and molecular interactions support the antioxidant, antimicrobial and hypolipidemic outlined effects in the in vitro and in vivo findings. In view of their prominent antioxidant effects, ACPs stand for promising candidates in liver diseases and need be considered in pharmaceutical applications.

The Capital Asset Pricing Model is a widely applied model to describe risky markets and to deduce their systematic risk. Its estimation, therefore, remains an important task in Econo-financial studies. Empirically, it focuses on the impact of return interval on the betas. Existing studies somehow turn around the same idea of measuring the value of the beta according to the uniform intervals of time during a fixed period. However, it is noticed easily, and especially in the last decade that many factors such as socio-political, and Econo-environmental ones have led to a perturbation in the timeline of the worldwide development, and especially in countries and regions having political changes. This led us to introduce a new idea of risk estimation taking into account the non-uniform changes in markets by introducing a non-uniform wavelet analysis. We aim to explain the Econo-political situation of Arab spring countries and the effect of the revolutions on the market beta. The main novelty is firstly the construction of a dynamic backward-forward model for missing data, and next the application of random non-uniform wavelets. The proposed procedure will be acted empirically on a sample corresponding to TUNINDEX stock as a representative index of the Tunisian market actively traded over the period January 14, 2016, to January 13, 2021. The chosen 5-years period is important as it constitutes the first 5-years-after the revolution and depends strongly on the Socio-Econo-political stability in the revolutionary countries.

Ocular drug delivery is one of the most challenging administration routes due to the very low drug bioavailability. In this work, we produce and characterize mucoadhesive mixed polymeric micelles (PMs) made of chitosan and poly(vinyl alcohol) backbones graft-hydrophobized with short poly(methyl methacrylate) blocks and use them to encapsulate cannabidiol (CBD), an anti-inflammatory cannabinoid. CBD-loaded mixed PMs are physically stabilized by ionotropic crosslinking of the CS domains with sodium tripolyphoshate and spray-drying. These mixed PMs display CBD loading capacity of 20% w/w and sizes of 100-200 nm, and spherical morphology (cryogenic-transmission electron microscopy). The good compatibility of the unloaded and CBD-loaded PMs is assessed in a human corneal epithelial cell line. Then, we confirm the permeability of CBD-free PMs and nanoencapsulated CBD in cornea cell monolayers under liquid-liquid and air-liquid conditions. Overall, our results highlight the potential of these polymeric nanocarriers for ocular drug delivery.

Recent years have seen dramatic growth in the number of scholarly scientific works dedicated to the topic of Artificial Intelligence (AI), banking, and finance. With the development of scientometric tools, it is now possible to map, visualize, analyze, and assess scientific activities in many fields of engineering and social sciences including Islamic banking and finance. Based on data retrieved from the Scopus database and using a qualitative method, this study investigates, evaluates, and identifies significant development, trends, and players in the application of AI in Islamic banking and finance using the Visualization Of Similarities Method (VOS) between objects in VOSviewer. From 2006 to 2022, 387 documents were retrieved from the Scopus database; Results revealed that the top five most active countries in terms of publications are Malaysia (117 documents), Indonesia (89 documents), the United Kingdom (36 documents), the USA (24 documents), and Saudi Arabia and Bahrain (24 documents each). The International Islamic University Malaysia and Universitas Indonesia came out on top of active institutions while the top funding source came from the Ministry of Higher Education, Malaysia. The comprehensive findings and analysis reported in this study serve as a roadmap for future academics to create theory and practice for applying AI in Islamic banking and finance.

Propagation of human cytomegalovirus (CMV) in cultured cells results in genetic adaptations that confer improved growth in vitro and significant attenuation in vivo. Mutations in RL13 arise quickly during cell culture passage, while mutations in the UL128-131A locus emerge later during fibroblast passage and disrupt expression of a glycoprotein complex that is important for entry into epithelial and endothelial cells. As in vivo CMV replicates in the context of host antibodies, we reasoned that antibodies might mitigate the accumulation of adaptive mutations during cell culture passage. To test this, CMV in infant urine was used to infect replicate fibroblast cultures. One lineage was passaged in the absence of CMV-hyperimmuneglobulin (HIG) while the other was passaged with HIG in the culture medium. The former lost epithelial tropism and aquired mutations disrupting RL13 and UL131A expression, whereas the latter retained epithelial tropism and both gene loci remained intact after 22 passages. An epitheliotropic RL13+/ UL131A+ virus was isolated by limiting-dilution in the presence of HIG and expanded to produce a working stock sufficient to conduct cell tropism experiments. Thus, culture in the presence of antibodies may facilitate in vitro experiments using viruses that are genetically more authentic than has been previously possible.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.

The chiral recognition of enantiomers is a topic of great importance. In this study, a straightforward and effective chiral detection strategy was developed for distinguishing between tryptophan (TRP) enantiomers. The approach involved the preparation of a magnetic molecularly imprinted chitosan (MMIC) for the sample preparation, which was combined with a nitrocellulose membrane (paper-based analytical device, PAD) integrated with D-TRP covalently-grafted polymethacrylic acid (PAD_PMA_D-TRP). The discrimination between TRP enantiomers was achieved using AuNPs as a colorimetric probe. Indeed, the presence of D-TRP rapidly induced the aggregation of AuNPs due to its strong affinity to PAD-PMA_D-TRP, resulting in a noticeable color change of the AuNPs from red to purple. On the other hand, L-TRP did not induce any color change. The chiral analysis could be easily performed with the naked eye and/or a smartphone. The developed method exhibited a detection limit of 3.3 µM and it was successfully applied to detect D-TRP in serum samples, demonstrating good recovery rates. The proposed procedure is characterized by its simplicity, cost-effectiveness, rapidity, and ease of operation.

The authors present a novel sensing platform for a disposable electrochemical, non-enzymatic glucose sensor strip at physiological pH. The sensing material is based on dendritic gold nanostructures (AuNs) resembling feather branches, which are electrodeposited onto a Laser-scribed 3D-Graphene electrode (LSGE). The LSGEs were fabricated via a one-step laser scribing process on a commercially available polyimide sheet. This study investigates several parameters that influence the morphology of the deposited Au nanostructures and the catalytic activity towards glucose electro-oxidation. The electrocatalytic activity of AuNs-LSGE was evaluated using Cyclic Voltammetry (CV), Linear Sweep Voltammetry (LSV), and Amperometry, and was compared to commercially available carbon electrodes prepared under the same electrodeposition conditions. The sensor demonstrated good stability and high selectivity of the amperometric response in the presence of interfering agents, such as ascorbic acid, when a Nafion membrane was applied over the electrode surface. The proposed sensing strategy offers a wide linear detection range, from 0.5 to 20 mM, which covers normal and elevated levels of glucose in the blood, with a detection limit of 0.21 mM. The AuNs-LSGE platform exhibits great potential for use as a disposable glucose sensor strip for point-of-care applications, including self-monitoring and food management. Its non-enzymatic features reduce dependence on enzymes, making it suitable for practical and cost-effective biosensing solutions.

Discovered as an apparent pattern, a universal relation between geometry and information called the holographic principle has yet to be explained. This relation is unfolded in the present paper. As it is demonstrated there, the origin of the holographic principle lies in the fact that a geometry of physical space has only a finite number of points. Furthermore, it is shown that the puzzlement of the holographic principle can be explained by a magnification of grid cells used to discretize geometrical magnitudes such as areas and volumes into sets of points. To wit, when grid cells of the Planck scale are projected from the surface of the observable universe into its interior, they become enlarged. For that reason, the space inside the observable universe is described by the set of points whose cardinality is equal to the number of points that constitute the universe’s surface.

This paper presents a new method for approximating the classical arcsine function. The proposed approximating methodology is simpler in its approach than other classical approaches and undeniably innovative. It is based on matrix representation besides the basic interpolation to approximate the inverse trigonometric function. It provides an efficient model which allows for reliable and precise calculations. The results are as per our knowledge unseen results in the previous literature.

The present paper is concerned with the study of the quality of life index. Such an index has become an important index for measuring the well-being of individuals. However, the quality of life index is always a subjective, intangible, and often hard to quantify with precision due to the lack of quantitative models dealing with. The main goal of the present paper is thus to propose a mathematical, quantitative model for the measurement of a quality of life index. The main novelty is firstly the construction of a wavelet dynamic multiscale model to quantify and investigate the effect of time scale on the quality of life index measuring. The proposed procedure is acted empirically on a sample corresponding to Saudi Arabia as a case of study during the period from 2003 to 2020 as part of the 2030-vision plan. Saudi Arabia has implemented the so-called 2030-vision plan where the quality of life improvement is one of the main goals to be attempted. The findings show that wavelets are capable to localize the time-wise behavior of the index contrarily to classical studies which estimate a global view of the index. Moreover, the study shows the link between the quality of life behavior and many other indices.

The relative operating characteristic (ROC) curve is a popular diagnostic tool in forecast verification, with the area under the ROC curve (AUC) used as a verification metric measuring the discrimination ability of a forecast. Along with calibration, discrimination is deemed as a fundamental probabilistic forecast attribute. In particular, in ensemble forecast verification, AUC provides a basis for the comparison of potential predictive skill of competing forecasts. While this approach is straightforward when dealing with forecasts of common events (e.g. probability of precipitation), the AUC interpretation can turn out to be oversimplistic or misleading when focusing on rare events (e.g. precipitation exceeding some warning criterion). How should we interpret AUC of ensemble forecasts when focusing on rare events? How can changes in the way probability forecasts are derived from the ensemble forecast affect AUC results? How can we detect a genuine improvement in terms of predictive skill? Based on verification experiments, a critical eye is cast on the AUC interpretation to answer these questions. As well as the traditional trapezoidal approximation and the well-known bi-normal fitting model, we discuss a new approach which embraces the concept of imprecise probabilities and relies on the subdivision of the lowest ensemble probability category.

Lysine plays a crucial role in promoting development, enhancing immune function, and improving the function of central nervous system tissues. The two configurational isomers of amino acids have significantly different effects. Currently, methods for chiral recognition of lysine all have drawbacks such as expensive equipment and complicated detection processes, whereas fluorescence analysis boasts high sensitivity, strong selectivity, and simple operation. In this study, we synthesized four novel Binaphthyl-Amine (BINAM)-based fluorescent probes capable of specifically identifying the L-configuration of lysine among the twenty amino acids constituting human proteins. The enantiomeric fluorescence enhancement ratio (ef or ΔIL/ΔID) reached up to 15.29, demonstrating high enantioselectivity. We also evaluated the probe's recognition ability under different pH, reaction times, and metal ion conditions, as well as the Limit of Detection of the probe. Our findings indicate that this probe is a highly stable tool for detecting chiral lysine.

We seek to examine effective collaboration when engaging in value cocreation with the customer for mobile financial services in EMs. Our study is a motivation for multi-stakeholder engagement in value cocreation with financial inclusion of all consumers including marginalized populations. Furthermore, our work discovers that social sustainability is a product of social creativity and results in financial inclusion. We apply a qualitative descriptive methodology utilizing exemplars from extant research and phenomenology to analyze the data from the contexts of Ghana and Kenya. The results show that value is co-created for mobile financial services in networks in emerging markets when actors integrate resources for social and environmental sustainability as essential elements for mobile financial inclusion.

The aim of our study was to evaluate the impact of T. gondii status on eosinophils count (PNE), eosinophil to lymphocyte ratio (ELR) and eosinophil to neutrophil to lymphocytes ratio (ENLR) before and after can-nabis cessation in patients with psychiatric disorders. One hundred and eighty-eight patients were includ-ed in the study. T. gondii, PNE, ELR, ENLR, and urinary cannabis were measured at baseline and after 4 weeks of cannabis cessation. Highest PNE (p = .02), ELR (p = .03) and ENLR levels (p = .031) and highest increase of PNE (p = .044), and ENLR (p = .036) levels were found in patients after cannabis cessation only in the Toxo+ group. At four weeks, significant interactions between cannabis and T. gondii status for PNE (p = .038), and for ENLR (p = .043) levels were found, as well as for the evolution between baseline and 4 weeks for ENLR level (p = .049). After cannabis cessation, we found a positive correlation between negative symptoms and PNE levels at 4 weeks in the Toxo+ group. This study shows that the increase of inflammation after cannabis cessation might be modulated by T. gondii seropositivity status in patient after cannabis cessation.

Atomic force microscopy (AFM) has been extensively used for the nanoscale characterization of polymeric materials. The coupling of AFM with infrared spectroscope (AFM-IR) provides another advantage to the chemical analyses and thus helps to shed light upon the study of polymers. In this perspective paper, we review recent progress in the use of AFM-IR in polymer science. We describe first the principle of AFM-IR and the recent improvements to enhance its resolution. We discuss then the last progress in the use of AFM-IR as a super-resolution correlated scanned-probe IR spectroscopy for chemical characterization of polymer materials dealing with polymer composites, polymer blends, multilayers and biopolymers. To highlight the advantages of AFM-IR, we report here several results in studying crystallization of both miscible and immiscible blends as well as polymer aging. Then, we demonstrate how this novel technique can be used to determine phase separation, spherulitic structure and crystallization mechanisms at the nanoscale, which have never been achieved before. The review also discusses future trends in the use of AFM-IR in polymer materials, especially in polymer thin film investigation.

This article presents, for the first time, the kinetics and the general conversion features of free radical polymerization (FRP) in a 3-component system (A/B/N), with [A] being the initiator, and [B] and [N] are additives, based on the proposed mechanism of Rahal et al. Higher FRP can be achieved by additives [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals (R) via the radicals (S' and S) produced by N.The initiator (coumarin) shows a dual photo-oxidation and photo-reduction character for high efficacy. The FRP conversion efficacy (CE) depends not only on the property of the initiator [A], the additives [B] and [N}, but also the types of monomers. For example, when [A]=CoumC, [A]/NPG is more efficient than [A]/Iod, but revserse trend occurs in some monomers. However, 2-component systems (with CE=0% to 80%) are always less efficient than that of 3-component systems (with CE=70% to 86%, in TMPTA). Specific systems with [A]=coumarins, [B]=Iodonium salt, and N=NPG are analyzed. Analytical formulas for the role of each component concentration, light intensity and coupling rates on the conversion efficacy are derived.

The solar water heater must be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for efficient Domestic Hot Water "DHW" storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, phase change material "PCM" mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58°C and 62.58°C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. In this proposed configuration, one liter of hot water may cost around 0.1362 DZD/liter (i.e., 0.00096 US$/liter) compared to 0.4431 DZD/liter for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer, and therefore, other solar collectors such as vacuum tube collectors may provide enhanced energy performance.