Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

The application of space robotic manipulators and heightened autonomy for ios represents a paramount pursuit for leading space agencies, given the substantial threat posed by space debris to operational satellites and forthcoming space endeavors. This work presents a guidance algorithm based on drl to solve for the space manipulator path-planning during the motion synchronization phase with the mission target. The goal is the trajectory generation and control of a spacecraft equipped with a 7-dof robotic manipulator, such that its end effector remains stationary with respect to the target point of capture. The ppo drl algorithm is used to optimize the manipulator’s guidance law, and the autonomous agent generates the desired joints rates of the robotic arm, which are then integrated and passed to a model-based feedback linearization controller. The agent is first trained to optimize its guidance policy and then tested extensively to validate the results against a simulated environment representing the motion synchronization scenario of an ios mission.

There are several well-described molecular mechanisms that influence cell growth and are relat-ed to the development of cancer. Chemokines constitute a fundamental element which are not only involved in local growth but also affect angiogenesis, tumor spread and metastatic disease. Among them, the C-X-C motif chemokine ligand 12 (CXCL12) and its specific receptor the chemo-kine C-X-C motif receptor 4 (CXCR4) have been widely studied. The overexpression in cell mem-branes of CXCR4 has been shown to be associated with the development of different kinds of his-tological malignancies, such as adenocarcinomas, epidermoid carcinomas, mesenchymal tumors or neuroendocrine neoplasms (NENs). The molecular synapsis between CXCL12 and CXCR4 leads to the interaction of G proteins and activation of different intracellular signaling pathways in both gastroenteropancreatic (GEP) and bronchopulmonary (BP) NENs conferring greater ca-pacity for locoregional aggressiveness, epithelial-mesenchymal transition (EMT) and the ap-pearance of metastases. Therefore, it has been hypothesized how to design tools that target this receptor. The aim of this review is to focus on current knowledge of the relationship between CXCR4 and NENs, with a special emphasis on diagnostic and therapeutic molecular targets.

The coronaviral pandemic has led to a shift in traditional teaching methods to more innovative approaches, such as high-fidelity patient simulation (HFPS), which can improve students’ clinical judgement and decision-making for quality patient care. A modified guideline was introduced to enhance students’ satisfaction and self-confidence in learning through HFPS. The study involved 189 baccalaureate nursing students, with 92 in the intervention group and 97 in the control group. The intervention group received the modified HFPS guideline, while the control group received standard treatment with basic instruction. After the HFPS debriefing session, students provided narrative feedback on their learning experience. The quantitative results showed that students in the intervention group reported a significant improvement in satisfaction and self-confidence in learning compared to the control group. The modified HFPS guideline provided clear guidance for students to learn and apply knowledge and skills more effectively, leading to increased engagement during interactive simulation sessions. The results suggest that the HFPS guideline should be added to the curriculum to enhance students’ satisfaction and self-confidence in learning, even in junior students. Innovative teaching methods, such as HFPS, can be necessary and beneficial for healthcare professional training, after the pandemic.

Different alcoholic beverages can have different effects on blood alcohol concentrations (BAC) and neurotoxicity even if equalized for alcohol content by volume. Anecdotal evidence suggested that natural wine is metabolized differently from conventional wines. This triple-blind study compared the BAC of 55 healthy male subjects after consuming the equivalent of 2 units of alcohol of a natural or conventional wine over 3 mins in two separate sessions one week apart. BAC was measured using a professional breathalyzer every 20 mins after consumption for 2 hrs. The BAC curves in response to the two wines diverged significantly at twenty minutes, at forty minutes and also at their maximum concentrations (peaks), with the natural wine inducing a lower BAC than the conventional wine (T20 0.40 vs. 0.46 [p<0.0002], T40 0.49 vs. 0.53 [p<0.0015], peak 0.52 vs. 0.56 [p<0.0002]). These differences are likely related to the development of different amino acids and antioxidants in the two wines during their production. This in turn may affect the kinetics of alcohol absorption and metabolism. Other contributing factors may also include pesticide residues, differences in dry extract content and the use of indigenous or selected yeasts. Further studies are needed to fully understand why natural wines are metabolized differently from conventional wines.

In the former mining district of La Carolina (southern Spain), waste materials were accumulated without first waterproofing the substrate. Additionally, these mining dams were abandoned without any type of restoration, conditions that present a significant risk of contaminating the surrounding soils and waters. Prior to carry out the necessary works for isolating these residues, morphological characterization of the contact with the base substrate is needed. For that purpose, in recent years, different indirect study techniques have been used, among which electrical to-mography stands out. In this work, a less common geophysical technique, magnetometry, both in its magnetic and gra-diometric modalities, is used as an alternative method to analyse the geometry and structure of a mining dam. The results obtained with this methodology are compared with the results provided by electrical techniques, as well as with direct data from mechanical surveys and aerial photo-graphs prior to waste deposition. The magnetic anomaly curves obtained with geometric models generated with the Mag2dc program were also analysed. This comparative study shows the use-fulness of magnetic prospecting in characterizing the base geometry of these mining structures and therefore the interest in its application to environmental characterization studies.

Background: Diabetes mellitus (DM) and osteoporosis are two of the most widespread metabolic disease in the world. The aim of this study is to investigate the prevalence of DM among patients affected by osteoporosis and fragility fractures, and to search differences in clinical features. Methods: 713 patients belonging to CTO Bone Unit because of osteoporosis and fragility fractures were divided into two groups, according to the diagnosis of DM. The clinical and bone characteristics of patients were compared. Results: Prevalence of DM was 10.8%. When compared to patients without DM, the median age at the time of first fracture was similar (72 years ± 14 IQR vs 71 years ± 12 IQR); prevalence of combination of vertebral and hip fractures was higher (p=0.039), as well as prevalence of males, although not significantly (p=0.051). Bone mineral density (BMD) at all sites was higher in DM group; Trabecular Bone Score (TBS), instead, was significantly lower (p&lt;0.001). Conclusions: Patients with fragility fractures and DM more frequently show combination of major fractures with higher BMD levels. In these patients, TBS could be a better indicator of bone health than BMD and therefore should be used as a diagnostic tool in clinical practice.

Purpose - The purpose of the study is to investigate the missing link between leadership style and job satisfaction among Mongolian public sector employees. This study reiterates the mediating role of organizational climate (OC) and work style (WS) in a new proposed model. Methodology - The questionnaire is designed by a synthesis of existing constructs in the current relevant literature. The research sample consisted of 143 officers who work in the primary and middle units of territory and administration of Mongolia. Factor analysis, reliability test, collinearity test, and correlation analyses confirm validity and reliability of the model. Multiple regression analysis, using Structural Equation Modeling (SEM), tests the hypotheses of the study. Practical implications - This study has several important implications for studies related to organizational behavior and job satisfaction. Furthermore, the implications of findings are beneficial to organizations aiming at improving policies and practices related to organizational behavior and human resource management. Regulators and supervisors of private or public organizations aiming to increase the level of their employees’ job satisfaction will also benefit from the findings. Therefore, this study’s new proposed model can be the basis of fundamental research to build a better human resource policy. Although leadership style is an influential factor for job satisfaction, this study identifies the mediating missing links between leadership style and employees’ job satisfaction. Findings: The findings of this research indicate that organizational climate and work style complement and fully mediate the relationship between leadership style and job satisfaction. Appropriate leadership style is most effective when it matches organizational climate as well as employees’ work style. Furthermore, suitable organizational climate will increases the level of job satisfaction. If work style of employees is respected and taken into consideration, leadership style can find its way into job satisfaction. Originality/value - This study is the first to understand the motivators of job satisfaction in government sector of Mongolia. This study suggests valuable findings for executive officers, junior and primary unit’s officers of register sector of government in Mongolia. The findings of this study help managers and executives in their effort to develop and implement successful human resource strategies.

Global coverage and scale up of interventions to reduce newborn mortality remains low, though progress has been achieved in improving newborn survival in many low-income settings. An important factor in the success of newborn health interventions, and moving to scale, is appropriate design of community-based programs and strategies for local implementation. We report the results of formative research undertaken to inform the design of a newborn health intervention in Cambodia. Information was gathered on newborn care practices over a period of three months using multiple qualitative methods of data collection in the primary health facility and home setting. Analysis of the data indicated important gaps, both at home and facility level, between recommended newborn care practices and those typical in the study area. The results of this formative research have informed strategies for behavior change and improving referral of sick infants in the subsequent implementation study. Collection and dissemination of data on newborn care practices from settings such as these can contribute to efforts to advance survival, growth and development of newborns for intervention research, and for future newborn health programming.

Rice, as a staple crop feeding billions, faces constant threats from various diseases jeopardizing global food security. Precise understanding of disease resistance mechanisms is crucial for developing resilient rice varieties. Traditional genetic mapping methods, such as QTL mapping, provide valuable insights into the genetic basis of diseases. However, the complex nature of rice diseases demands a holistic approach to gain accurate knowledge of it. Omics technologies, including genomics, transcriptomics, proteomics, and metabolomics, enable a comprehensive analysis of biological molecules, uncovering intricate molecular interactions within the rice plant. Integration of various mapping techniques using multi-omics data has revolutionized our understanding of rice disease resistance. By overlaying genetic maps with high-throughput omics datasets, researchers can pinpoint specific genes, proteins, or metabolites associated with disease resistance. This integration enhances the precision of disease-related biomarkers with better understanding of their functional roles in disease resistance. Improvement of rice breeding for disease resistance through this integration represents a significant stride in agricultural science because better understanding of the molecular intricacies and interactions underlying disease resistance architecture leads to more precise and efficient development of resilient and productive rice varieties. In this review, we explore how the integration of mapping and omics data can give a transformative impact on rice breeding for enhancing disease resistance.

Flavours of Glenroy (2013-4) was a socially engaged art research project focused on developing strategies to connect the diverse, mobile and transforming community of Glenroy through the theme of growing and distributing edible plants. The project was action research based, where artist researchers used creatively imagined mobile edible gardens to connect and engage with locals through project presentation and execution. The process of producing, presenting and conversing about edible gardening revealed Glenroy to be a transnational Australian dream suburb, reflecting the fluid globalising conditions of our cities. The project emphasized how social relations encouraged through art, has the capacity to transform social spaces, providing a platform to introduce new voices and narratives of a community and encourage inclusive participation in sustainable citizenship.

In the last decade, the tremendous improvement in the sensitivity and also affordability of Liquid Chromatography-tandem Mass Spectrometry (LC-MS/MS) have revolutionized its application in pharmaceutical analysis, resulting in wide-spread of employing LC-MS/MS for determining pharmaceutical compounds including anticancer drugs in pharmaceutical research and also industries. Currently, LC-MS/MS has been widely used to quantify small molecule oncology drugs in various biological matrices to support preclinical and clinical Pharmacokinetic studies in R & D of oncology drugs. This mini-review article will describe the state-of-the art LC-MS/MS and its application in rapid quantification of small molecule anticancer drugs. In addition, efforts have also been made in this review to address several key aspects in the development of rapid LC-MS/MS methods, including sample preparation, chromatographic separation and matrix effect evaluation.

In the rapidly evolving field of data management, numerous terminologies, such as data warehouse, data lake, data lakehouse, and data mesh , have emerged, each representing a unique analytical data architecture. However, the distinctions and similarities among these paradigms often remain unclear. The present paper aimed to navigate the data architecture landscape by conducting a comparative analysis of these paradigms. The analysis a identified and elucidated the differences and similari- ties in features, capabilities, and limitations of these architectural constructs. The study outcome serves as a comprehensive guide, assisting practitioners in selecting the most suitable analytical data architecture for their specific applications.

The study reported the analytical approach on nine coins found in the wreck A of Fontanamare for understanding the complex corrosion processes that take place in underwater conditions. Optical microscopy (OM), combined with micro-Raman (µ-Raman) spectroscopy, and X-ray diffractometry (XRD) and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM + EDS) were used to analyse the nature and the microstructure of the corrosion patina in comparison with the non-degraded state of coins. Three main type of corrosion patina based on copper, lead chloride and carbonate were identified: white-green, black and the obtained results for understanding the complex corrosion processes that take place in underwater conditions.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

The food system, the most important driver of planetary transformation, is in a deep crisis. Therefore, seeking a sustainable and socially-fair transition pathway becomes an issue of utmost priority for our own survival. The consideration of food as a commodity, a social construct that played a central role in driving this crisis, remains the uncontested narrative to lead the different transition pathways what seems rather contradictory. By exploring the normative values in the transition landscape, this paper seeks to understand how relevant is the hegemonic narrative of “food as commodity” and its alternative of “food as commons” to determine transition trajectories and food policy beliefs. Applying the Multi-level Perspective framework and developing the ill-studied “agency in transition”, this research enquired food-related professionals that belong to an online community of practice (N=95) on valuation of food dimensions and agency in food transitions to check whether the valuation of food is relevant to explain personal stances in transition. Results suggest the socially-constructed view of food as commodity is positively correlated to the gradual reforming attitude, whereas food as commons is positively correlated to the counter-hegemonic transformers regardless the self-defined position in the transition landscape (regime or niches). At personal level, there are multiple loci of resistance with counter-hegemonic attitudes in varied institutions of the regime and the innovative niches, many of them holding this discourse of food as commons. Conversely, alter-hegemonic attitudes are not positively correlated to this alternative discourse and they may inadvertently or purportedly reinforce the ‘‘neoliberal narrative’’. Food as commons, a different narrative whose rationale is explained in the paper, seems to be a relevant framework that could enrich the multiple transformative constituencies that challenge the industrial food system and therefore facilitate the convergence of movements that reject the commodification of food.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

El Niño is warming of the sea surface temperature of the Pacific Ocean. Extreme flooding, drought, lack of potable water for livestock and domestic use, food insecurity and market imbalance are associated with El Niño and La Niña in Ethiopia. Drought following El Niño caused 50 to 90% crop failure, in the eastern parts of Ethiopia. El Niño episodes are detected using different statistical indices such as Oceanic Nino Index (ONI), Agricultural Stress Index System (ASIS) and the Southern Oscillation Index (SOI), with magnitude ranging from weak to strong. Identifying the El Niño and La Niña seasons it is very important to adopt suitable adaptation strategies, which can resolve and/or reduce the negative impacts. Early warning and immediate support to the impacted areas have been carried out to minimize risks from El Niño animal feed for livestock from other areas has been transported to the vulnerable areas. Planting early maturing and drought resistant crops, supplementary irrigation, early waning information on weather and climate have been exercised as climate change adaptation strategies, early warning mechanisms by the government of Ethiopia. El Niño and La Niña are natural phenomena; however, it is necessary to study the occurrence and distribution of El Niño and La Niña episodes to enable early warning and identify suitable adaptation strategies and policy implications in the country.

Lipoxygenases are non-heme iron-containing enzymes that catalyze the oxidation of polyunsaturated fatty acids, resulting in the production of lipid hydroperoxides, which are precursors of inflammatory lipid mediators. The enzymes are widely distributed in humans, other eukaryotes, and cyanobacteria. Lipoxygenases hold promise as therapeutic targets for several human diseases, including cancer and inflammation-related disorders. Inhibitors of lipoxygenase have potential applications in pharmaceuticals, cosmetics, and food. Bioactive peptides are short amino acid sequences embedded within parent proteins, which can be released by enzymatic hydrolysis, microbial fermentation, and gastrointestinal digestion. A wide variety of bioactivities have been documented for protein hydrolysates and peptides derived from different biological sources. Recent findings indicate that protein hydrolysates and peptides derived from both edible and non-edible bioresources can act as lipoxygenase inhibitors. In this review, we explore current knowledge on the production of anti-lipoxygenase protein hydrolysates and peptides from millet grains, chia seeds, insects, milk proteins, fish feed, velvet antler blood, fish scales, and feather keratins. We delve into the anti-lipoxygenase activities and modes of action of these protein hydrolysates and peptides, while also highlighting the strengths and shortcomings of previous research. Additionally, we propose potential research directions and areas of improvement that can propel the discovery of anti-lipoxygenase peptides in the near future.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

1) Background: A population-based cross-sectional study was conducted to understand how green cover and accessibility of common public open spaces in compact urban areas affect physical activeness of resident. 2) Methods: A total of 554 residents completed a structured questionnaire on quality-of-life, physical activity level, and healthy eating practice. 3) Results: The sampled population lived with green cover averaged 10.11 ± 7.95% (ranged 1.56–9.88), whereas majority (90%) of the residents performed physical activities at medium and high levels. Metabolic Equivalent of Task (MET)-minutes/week was associated with the green cover percentage (Pearson r = 0.092; p < 0.05). Irrespective of age and physical activity level, active residents commonly used public open spaces within district for performing exercise, especially parks and promenade were mostly used by older residents while sports facilities by the younger groups. 4) Conclusions: Current findings suggested promotion of exercise could be achieved by the design or redesign of built environment to include more parks accessible to the residents with the increase of vegetation.

It has been more than a century since Erlang published his paper in 1909. The classical queueing system for the M/D/c queue has been investigated by many authors. The key is to find the roots of an equation using explicit or numerical methods. We present an alternate form of explicit solution(s) of this/these root(s) using the Lambert-W function in this paper. In addition, the unsaturated probabilities of the number of customers in the system is derived explicitly in terms of this/these root(s). Finally, the mean number of customers in the system and the mean queueing delay are obtained from these probabilities. The exact queueing delay formula for the M/D/c queue is expressed in closed-form in terms of the root(s). Numerical results show that they are in excellent agreement with the numerical results published by Seelen, Tijms and Van Hoorn.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at &lt;2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) &gt; MRI (2.14 ± 0.08) &gt; EEG (1.87 ± 0.09) &gt; SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) &gt; MRI (0.518) &gt; EEG (0.446) &gt; SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) &gt; MRI (2.558) &gt; EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

On 19 September 2021, La Palma volcano (Canarias Archipelagos) started an eruption that persisted until 13 December 2021. Despite the Volcano Explosive Index (VEI) being estimated equal to 3, corresponding to not so powerful eruption, the long eruption activity posed much scientific in-terest in this natural hazard event. In this paper, we searched for possible effects of this eruption on the atmosphere and ionosphere, investigating the climatological archive and Swarm magnetic satellite data. In particular, we explored Aerosol, Sulphur Dioxide and Carbon Monoxide con-centrations in the atmosphere identifying both the direct emissions from the volcano as well as the plume that drifted toward West-South-West and was reinforced during the eruption period. The vertical profile of temperature from the Saber satellite was analysed to search for the possible presence of acoustic gravity waves induced by volcanic activity. Compared with the year before without eruption in the areas, a lot of Saber profiles present an Energy Potential very much higher than the previous year, proposing the presence of Acoustic Gravity Waves (AGW) induced by volcano eruption activity. We also identified Swarm magnetic disturbances on the day of the eruption and in November. The mechanism of coupling could be different for the latter one, as there is no evidence for AGW. They may be due to a more complex of physical and chemical al-terations that propagate from the lower atmosphere to the upper one into the ionosphere.

Blockchain technology (BCT) has the potential for sustainable development, enhancing business efficiency, reducing costs, and strengthening data security. Despite its potential, adoption among small and medium-sized enterprises (SMEs) is low due to the need for significant changes in technology infrastructure and the challenge of interoperability. A cross-sectional survey was done with 226 Hong Kong SMEs. The PLS-SEM results highlighted favorable transformation conditions as the most critical factor for SMEs considering the adoption of BCT. These conditions address both internal and external readiness for adopting the disruptive strategy. Other contributing factors to BCT adoption include trust in BCT developers, perceived usefulness and ease of use, government support, and perceived security. The research results contributed to the literature on disruptive technology acceptance, adoption, transformation conditions, technology readiness, and SMEs’ technology adoption. Government-supported policies and initiatives can promote BCT adoption, including educational programs, case studies, and resources for readiness. Financial support and regulatory frameworks can further encourage adoption. BCT developers can demonstrate the value of their systems, effectively communicate potential ROI and cost savings, and provide user-friendly interfaces to increase SMEs’ intention to adopt BCT.

Glioblastoma multiforme (GBM) is the most frequent and aggressive primary brain tumor. GBM is formed by a very heterogeneous astrocyte population, neurons, neovascularization and infiltrating myeloid cells (microglia and monocyte derived macrophages). The IQGAP1 scaffold protein interacts with components of the cytoskeleton, cell adhesion molecules, and several signaling molecules to regulate cell morphology and motility, cell cycle and other cellular functions. IQGAP1 overexpression and delocalization has been observed in several tumors, suggesting a role for this protein in cell proliferation, transformation and invasion. IQGAP1 has been identified as a marker of amplifying cancer cells in GBMs. To determine the involvement of IQGAP1 in the onco-biology of GBM, we performed immunohistochemical confocal microscopic analysis of the IQGAP1 protein in human GBM tissue samples using cell type-specific markers. IQGAP1 immunostaining and subcellular localization was heterogeneous; the protein was located in the plasma membrane and, at variable levels, in nucleus and/or cytosol. Moreover, IQGAP1 positive staining was found in podosome/invadopodia-like structures. IQGAP1⁺ staining was observed in neurons (Map2⁺ cells), in cancer stem cells (CSC; nestin⁺) and in several macrophages (CD31⁺ or Iba1⁺). Our results indicate that the IQGAP1 protein is involved in normal cell physiology as well as oncologic processes.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

Zika virus (ZIKV) infection and pathogenesis are linked to the disruption of neurogenesis, congenital Zika syndrome and microcephaly by affecting neural progenitor cells. Nonstructural protein 5 (NS5) is the largest product encoded by ZIKV-RNA and is important for replication and immune evasion. Here, we studied the potential effects of NS5 on microtubules (MTs) and autophagy flux, together with the interplay of NS5 with histone deacetylase 6 (HDAC6). Fluorescence microscopy, biochemical cell-fractionation combined with the use of HDAC6 mutants, chemical inhibitors and RNA interference indicated that NS5 accumulates in nuclear structures and strongly promotes the acetylation of MTs that aberrantly reorganize in nested-like structures. Similarly, NS5 accumulates the p62 protein, an autophagic-flux marker. Therefore, NS5 alters events that are under the control of the autophagic tubulin-deacetylase HDAC6. HDAC6 appears to degrade NS5 by autophagy in a deacetylase- and BUZ domain-dependent manner and to control the cytoplasmic expression of NS5. Moreover, NS5 inhibits RNA-mediated RIG-I interferon (IFN) production, resulting in greater activity when autophagy is inhibited (i.e., effect correlated with NS5 stability). Therefore, it is conceivable that NS5 contributes to cell toxicity and pathogenesis, evading the IFN-immune response by overcoming HDAC6 functions. HDAC6 has emerged as an anti-ZIKV factor by targeting NS5.

The experiences gathered during the past 30 years support the operational use of irrigation scheduling based on frequent multi-spectral image data. Currently, the operational use of dense time series of multispectral imagery at high spatial resolution makes monitoring of crop biophysical parameters feasible, capturing crop water use across the growing season, with suitable temporal and spatial resolutions. These achievements, and the availability of accurate forecasting of meteorological data, allow for precise predictions of crop water requirements with unprecedented spatial resolution. This information is greatly appreciated by the end users, i.e. professional farmers or decision-makers, and can be provided in an easy-to-use manner and in near-real-time by using the improvements achieved in web-GIS methodologies. This paper reviews the most operational and explored methods based on optical remote sensing for the assessment of crop water requirements, identifying strengths and weaknesses and proposing alternatives to advance towards full operational application of this methodology. In addition, we provide a general overview of the tools which facilitates co-creation and collaboration with stakeholders, paying special attention to these approaches based on web-GIS tools.

The process of establishing secure communication between devices in the Internet of Things (IoT) can be approached by using a One-time-Pad (OTP) protocol. We propose using a known secure multiparty sum protocol for generating a One-time-Pad key using true (physical) random numbers in each device (party). We implemented the proposal using ZeroC-Ice, a middleware for distributed computing. The protocol security properties were analyzed under the assumptions of the Dolev-Yao threat model.

Antler is the fastest growing tissue. Because is based on proto-oncogenes, to avoid the risk of cancer, antlers evolved strong anticancer mechanisms, and thus its extract (DVA) is effective also against the few human tumours studied so far. We assessed whether DVA is a general anticancer compound testing direct effects in cells of different tumours: glioblastoma (GBM), colorectal and breast cancer, and leukaemia. DVA reduced viability of tumour but not healthy cells. Mobility decreased at least at the longest test (72 h). Intraperitoneal/oral 200 mg DVA/kg administration in GBM xenograft mice for 28 d reduced tumour weight 66.3% and 61.4% respectively, and also spleen weight. In addition, tumours treated with DVA showed symptoms of liquefactive necrosis. Serum cytokines showed DVA up-regulated factors related with tumour fighting and down-regulated those related with inducing immune tolerance to the tumour. DVA shows general anticancer effects in the lines tested and, in GBM mice, also strong indirect effects apparently mediated by the immune system.

As of July 7, 2022, the total number of confirmed cases caused by COVID-19 has reached 544,324 million, and the total number of 6.333 million deaths (WHO). Older people were globally the most vulnerable during the pandemic. This paper examined the mortality and psychological crisis of older people during the pandemic in four cities, namely Wuhan, Milan, London, and Hong Kong. The selection of cities was based on different degrees of social connectedness of older people and chronologically to cover the whole period of the outbreak from January 2020 to August 2022. Older people in Milan and Wuhan tended to rely on the close family relationship during times of crisis. Meanwhile, older people in Hong Kong and London were more dependent on social services. Both quantitative and qualitative approaches were employed to analyze the situations of older people under different government responses and the strengths and weaknesses of respective healthcare systems. Government reports and official statistics were used to illustrate the seriousness of each city's COVID-19 outbreak while stories reported by the press, NGOs, and journal articles were used to reflect the reactions of the older people. Interactions of social culture, health care provisions, and government responses to the pandemic were discussed from the perspective of health welfare regimes. On one hand, results showed that governments have not learned from the experiences of other countries. On the other hand, older people have not successfully coped with the life-threatening stress by breaking institutional boundaries and redefining cultural norms.

Autophagy is an evolutionarily conserved central process in host metabolism. Among its major functions are conservation of energy during starvation, recycling organelles, and turnover of long-lived proteins. Besides, autophagy plays a critical role in removing intracellular pathogens and very likely represents a primordial intrinsic cellular defence mechanism. More recent findings indicate that it has not only retained its ability to degrade intracellular pathogens, but also functions to augment and fine tune antiviral immune responses. Interestingly, viruses have also co-evolved strategies to manipulate this pathway and use it to their advantage. Particularly intriguing is infection-dependent activation of autophagy with positive stranded (+)RNA virus infections, which benefit from the pathway without succumbing to lysosomal degradation. In this review we summarise recent data on viral manipulation of autophagy, with a particular emphasis on +RNA viruses and highlight key unanswered questions in the field that we believe merit further attention.

Prostate cancer is the second leading cause of death in males in America, with advanced prostate cancers exhibiting a 5-year survival rate of only 32%. Castration-resistance is often developed during the course of treatment, though its influences require further understanding. This study explores the human microbiome for its implications in castration-resistance and metastasis in prostate cancer. RNA sequencing data was downloaded for bone and soft tissue biopsies of patients with metastatic castration-resistant prostate cancer. These sequences were mapped to bacterial sequences to yield species-level abundance approximations. Numerous species were found to correlate to the expression of known markers of castration-resistance, including AR, PI3K, and AKT. Castration-resistance-associated signaling pathways were also enriched with these species, including PI3K-AKT signaling and endocrine resistance. For their implications in cancer aggression and metastasis, cancer stem cell markers were further explored for relation to these species. EGFR and SLC3A2 were widely downregulated with greater abundance of most species. Our results suggest that the microbiome is heavily associated with castration-resistance and stemness in prostate cancer. By considering the microbiome’s importance in these factors, we may better understand the highly aggressive and highly invasive nature of prostate cancer, allowing for needed improvement in the treatment of this disease.

The aim of this study is to analyse the names given to streets, monuments, spots of interest, et cetera in a street guide of an imaginary city called The Manada, whose map is constructed as a painting. For this analysis, we start from the 257 entries of the Street Guide, select their possible antecedents in literature and contextualize this street guide with respect to these antecedents. Our methodology is focused on two specific aspects of the Street guide: (1) to detect the semantic fields that emerge (with a methodology inverse to the creative one, that is, asking ourselves what key questions would result in the names of the streets) and (2) to detect the literary devices that are put into practice in the names of the places on the map, in order to determine how the relationship with the viewer-reader is established from a connotative level. The main findings of this study demonstrate that this is a unique piece, a new format both pictorial and literary, and that it has transcendence in the theme it deals with: the concealment of systemic violence. Comments about feminism, apotropaic devices and surrealism end our text.

Chronic kidney disease (CKD) affects approximately 12% of the global population posing a significant health threat. Inflammation plays a crucial role in the uremic phenotype of CKD contributing to elevated cardiovascular and overall mortality in affected individuals. This study aimed to explore novel metabolic pathways in non-dialysis dependent stage 5 CKD patients using semitargeted metabolomics. In a prospective observational design involving 50 patients, blood samples collected before the initial hemodialysis session underwent liquid chromatography and high resolution mass spectrometer analysis. Univariate (Mann-Whitney test) and multivariate (logistic regression with LASSO regularization) methods identified metabolomic variables associated with inflammation. Notably, adenosine-5’-phosphosulfate (APS), dimethylglycine, pyruvate, lactate, and 2-ketobutyric acid exhibited significant differences in the presence of inflammation. Cholic acid, homogentisic acid, and 2-phenylpropionic acid displayed opposing patterns. Multivariate analysis indicated increased inflammation risk with certain metabolites (N-Butyrylglycine, dimethylglycine, 2-Oxoisopentanoic acid, and pyruvate), while others (homogentisic acid, 2-Phenylpropionic acid, and 2-Methylglutaric acid) suggested decreased probability. These findings unveil potential inflammation-associated biomarkers related to defective mitochondrial fatty acid beta oxidation and branched-chain amino acid breakdown in CKD, shedding light on cellular energy production and offering insights for further clinical validation.

Background. Escalating global plastic production, expected to reach 34,000 million tons by 2050, poses a significant threat to human and environmental well-being, particularly in aquatic ecosystems. Microplastics (MP) and nanoplastics (NP), which originate from the degradation of plastics, are of concern due to their potential bioaccumulation and uptake of pollutants. This study addresses identification methods and focuses on insect meal, a raw material for aquaculture feed. Methods. By using different techniques, the study was able to detect MP and NP in insect meal samples. Chemical digestion with KOH at 60°C efficiently removed organic matter without affecting the synthetic polymer polyethylene (PE). Filtration, confocal Raman microscopy, SEM and TEM were used for comprehensive analysis and integrity tests on PE films were performed using Raman and FTIR spectroscopy. The results showed the presence of PE microplastic particles in the insect meal, which was confirmed by correlative Raman and SEM mapping on a positively charged surface. In addition, the increased resolution of the Raman microscope identified submicrometric PE NP (800 nm). Transmission electron microscopy (TEM) with energy dispersive X-ray spectroscopy (EDX) confirmed plastic-like structures in the insect meal, highlighting the presence of PE plastics characterized by irregular shapes and some agglomeration. The higher carbon concentration in the EDX analysis supported the plastic nature, which was also confirmed by Raman spectroscopy. Conclusions. The study provides a robust method for the detection of MP and NP in insect meal and provides valuable insight into the possible presence of plastics in insect-based aquafeeds. The combination of different analytical methods increases the reliability of the results and sets the stage for future investigations that could focus on the quantification of NP and the assessment of their potential environmental impact.

Up to 13 million tons of plastic waste are estimated to enter the oceans every year. A generally accepted picture based on an increasing number of environmental studies suggests that the largest fraction of it consists or is rapidly degraded into microplastics (MPs). Most of the analytical studies focused on MPs are based on the detection and identification of the polymers. On the other hand, plastic debris in the environment undergo chemical (mainly photoxidative) and physical degradation processes leading not only to fragmentation but also to the formation of leachable, soluble and/or volatile degradation products that are released in the environment. The formation of such low molecular weight species is generally neglected in the studies on MPs even if these compounds, released in the environment from the plastics debris, may pose even higher risks for the environment and for the biota than the MPs particles themselves, risks that are far from being understood and assessed. In this study we performed the analysis of reference MPs - polymer micropowders obtained by grinding a set of five polymer types down to final size in the 857-509 μm range, namely high- and low-density polyethylene (HDPE and LDPE, respectively), polystyrene (PS), polypropylene (PP), and polyethylene terephthalate (PET). The reference MPs were artificially aged in a Solar-Box and their degradation products were analyzed to investigate their degradation processes. In particular, a systematic and thorough characterization of the aged (photo-oxidized) MPs and of their low molecular weight and/or highly oxidized fraction extractable in polar organic solvents was performed. For this purpose, the artificially aged MPs were subjected to selective extraction with organic solvent that are non-solvents for the virgin polymers, targeting selective recovery of the low molecular weight fractions generated during the artificial aging. Analysis of both the extractable fractions and the residues was carried out by a multi-technique approach combining evolved gas analysis-mass spectrometry (EGA-MS) and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). Up to 18 wt% of newly extractable, low molecular weight fraction was recovered from the photo-aged MPs, depending on the polymer type. The results highlight the need for more extensive studies about the potential harmfulness of the oxidation products (molecular and oxidized oligomeric species) that may leach out from plastic debris during their permanence in the environment.

The Asian clam Corbicula fluminea is a native aquatic species in Eastern Asia and Africa but has become one of the most ecologically and economically harmful invasive species in aquatic ecosystems in Europe, North America, South America. Due to their natural characteristics as a hermaphroditic species with high fecundity and dispersal capacity, Asian clams are extremely difficult to eradicate once they have infiltrated a waterbody. This is an emerging issue for states in the Northeastern United States as Asian clams expand their range farther North due to climate change. There has been extensive research conducted to develop chemical treatments to reactively control invasive mollusc populations and proactively prevent their further spread. However, treatments are mostly targeted toward biofouling bivalves in industrial settings. A comprehensive review of Asian clam chemical treatments used in open water systems was performed to evaluate molluscicides and identify toxicity ranges of emerging treatments that maximize Asian clam mortality and minimize negative impact to water quality and non-target species. The potential chemical applications in Asian clam control and management are summarized in this report to assist resource managers and practitioners on invasive Asian clam management.

In the last decades, the impacts of urbanization on the hydrological cycle have led to an increase in the frequency and magnitude of urban flooding events, also amplified by the effects of climate change. Sustainable Drainage Systems (SuDS) provide a revolutionary change in this field, improving the sustainability and resilience of cities. This research explores the integration of different SuDS with the aim of significantly reducing both flow volume and celerity of floods in a residual urban catchment area of metropolitan city of Querétaro (Mèxico), where extreme rainfall frequently occurs. This catchment is a representative suburb of urban pressure and environmental degradation problems. Currently, managing storm water under climate uncertainty through a multi-disciplinary approach is a major concern in this urban area. A 1D-2D coupling model of shallow water equations, finite volume method, unstructured meshing method, and hybrid parallel computing application defined the optimal configuration of SuDS at catchment scale to reduce the flood vulnerability in Querétaro. Specifically, in this paper we explore the management issues of the proposed SuDS configuration that acts as a water resource system with multiple purposes. A generic simulation model called MODSIM was applied to simulate the designed urban drainage system under a balanced IPCC future climate scenario in terms of reliability, resilience and vulnerability against water scarcity.

The La Oroya metallurgical complex reveals a process of structural or power pathology, where economic and environmental social policies lead to a citizenry without systemic freedom, characterized by environmental contamination (PAMA executed on average 67%, some processes with 0%) and sanitary (plumbosis 8.39 to 10.28 μg / dL), the economic dependence of this industry is also observed, which caused the weakening of the communities to maintain autonomy over their own destinies.The Doe Run Peru, operated the metallurgical complex, creating added value to the extractive-export chain of mineral concentrate, but also took advantage of the legal loopholes, the little coordination between the State institutions and the little authority of the supervisory institutions to get the most out of it, complying with the law in some cases, but without moral quality in some others, such as health in the oroinos.Government institutions must have strong links that provide a normative framework with prospects with sustainable development, where the beneficiary is society and not only certain interest groups. The economic benefits of the metallurgical complex operation are multiple, which begin with labor, the purchase and sale of materials and services, the collection of taxes and energy.

This paper presents the design and implementation of a multichannel bio-impedance spectroscopy system on field programmable gate arrays (FPGA). The proposed system is capable of acquiring multiple signals from multiple bio-impedance sensors, process the data on the FPGA and store the final data in the on-board Memory. The system employs the Digital Automatic Balance Bridge (DABB) method to acquire data from biosensors. The DABB measures initial data of a known impedance to extrapolate the value of the impedance for the device under test. This method offers a simpler design because the balancing of the circuit is done digitally in the FPGA rather than using an external circuit. Calculations of the impedance values for the device under test were done in the processor. The final data is sent to an onboard Flash Memory to be stored for later access. The control unit handles the interfacing and the scheduling between these different modules (Processor, Flash Memory) as well as interfacing to multiple Balance Bridge and multiple biosensors. The system has been simulated successfully and has comparable performance to other FPGA based solutions. The system has a robust design that is capable of handling and interfacing input from multiple biosensors. Data processing and storage is also performed with minimal resources on the FPGA.

A new trend in cow's milk has emerged in the market called type A1 and A2 milk. These products have piqued the interest of both consumers and researchers. Recent studies suggest that A2 milk may have potential health benefits, which is why researchers are investigating this product further. It is interesting to note that the A1 and A2 milk types have area-specific characteristics compared to breed-specific characteristics. Extensive research has focused on milk derivatives obtained from cow’s milk, primarily through in vitro and animal studies. However, few clinical studies have been conducted in humans, and the results have been unsatisfactory. New molecular techniques for identifying A1 and A2 milk may help researchers to develop new studies that can clarify certain controversies surrounding A1 milk. It is essential to exercise extreme caution when interpreting the updated literature. It has the potential to spread panic worldwide and have negative economic implications. Therefore, this study aims to investigate the new aspects of A1 and A2 milk in different research areas and clarify some aspects regarding these two types of milk.

Our goal was to determine the cellular immune response (CIR) among a random sample of the Borriana COVID-19 cohort (Spain) to identify its associated factors and their relationship with infection, reinfection and sequelae. We conducted a nested case-control study using a randomly selected sample of 225 individuals age 18 and older, including 36 individual naïve to SARS-CoV-2 infection, and 189 infected patients. We employed flow cytometry-based immunoassays for intracellular cytokine staining, utilizing Wuhan and BA.2 antigens and chemoluminescence microparticle immunoassay for detection SARS-CoV-2 antibodies. Logistic regression models were used. A total of 215 (95.6%) participants exhibited T-cell response (TCR) to at least one antigen. Positive responses of CD4+ and CD8+ T cells were 89.8% and 85.3% respectively. No difference in CIR was found for naïve and infected patients. Patients who experienced sequelae exhibited higher CIR than those without. A positive correlation was observed between TCR and Anti-Spike IgG levels. Factors positive associated with TCR included A-blood group, number of SARS-CoV-2 vaccine doses received, and Anti-N IgM; factors inversely related were the time elapsed since the last vaccine dose or infection, and B-blood group. These findings contribute valuable insights into the nuance immune landscape shaped by SARS-CoV-2 infection and vaccination.

The maintenance of traditional agricultural practices in protected small islands is closely linked to the preservation of the land, the protection of natural resources, and the conservation of local traditions. For this purpose, the Tuscan Archipelago National Park promoted the census of ancient horticultural varieties preserved by some farmers on the island of Elba. The survey revealed a deep-rooted historical, cultural, social, and economic link between this germplasm and the island’s territory. A scientific characterization of the landrace under ethnobotanical, morphological, and genetic aspects was carried out. Among these local varieties, two landraces of the Brassica species and three landraces of the Phaseolus species were identified and analyzed in this study. To ascertain their distinguishability and uniqueness, similar varieties were also identified based on morpho-physiological characteristics or territorial proximity and compared with the Elban landraces. Morpho-phenological data were collected, and molecular analyses were carried out using Simple Sequence Repeats (SSR) markers. Ten different SSR loci were considered for the Phaseolus species and nine for the Brassica species. The Tuscan Archipelago landraces showed a high level of internal variability but were clearly distinct from each other and from the analyzed varieties, as shown by AMOVA (Analysis of Molecular Variance). Their distinctness was further highlighted by the UPGMA dendrogram obtained from the genetic distance matrix. The same results were confirmed by Principal Coordinate Analysis (PCoA). This study confirms the peculiarity of the Elban landraces, their biodiversity is a heritage to be safeguarded, which can also be used in future breeding programs. These ancient Elban landraces were allocated to local farmers (most were young farmers) to protect them from extinction and to promote more resilient varieties cultivation compared to commercial hybrids widely spread in the area. Local farmhouses also play a strategic role in safeguarding the germplasm and dissemination of sustainable agricultural practices. There is high demand for ancient Elban landraces, this has led to the development of a new local economy balanced between agricultural tradition and innovation.

The COVID-19 pandemic has exposed the inadequacies of the current healthcare system and needs a paradigm change, which is holistic, and community based illustrated by the healing wheel. The present paper proposes that existential positive psychology (PP 2.0) represents a promising approach to meet the rising needs in palliative care. This framework has a twofold emphasis on (a) How to transcend and transform suffering as the foundation for wellbeing, and (b) how to cultivate our spiritual and existential capabilities to achieve personal growth and flourishing. We propose that these objectives can be achieved simultaneously through dialectical palliative counselling, as illustrated by Wong’s integrative meaning therapy (Wong, 2020) and Lo’s Conceptual Model of CALM Therapy in palliative care (Lo et al., 2014). We then discuss existential suffering in general and at the last stage of life in particular; we also review recent research and interventions on existential suffering in palliative patients. Finally, we outline the objectives and the strategies of IMT in providing palliative counselling for palliative care and hospice patients.

Anemia is a well-developed discipline where the concepts of precision medicine have, in part and being studied extensively. This review discusses the treatment of EPO-deficient anemia and resistance in Chronic Kidney Disease (CKD). Traditionally, erythropoietin-stimulating agents (ESA) and iron supplementation have been used to manage anemia in CKD. However, these treatments have potential risks, including cardiovascular and thromboembolic events. Newer treatments have emerged to address these risks, such as slow-release and low-dosage intravenous iron, oral iron, and erythropoietin-iron combination therapy. Another novel approach is using hypoxia-inducible factor prolyl hydroxylase inhibitors (HIF-PHI). This review highlights the need for precision medicine targeting genetic components of EPO-deficient anemia in CKD and discusses individual variability of genes such as the erythropoietin gene (EPO), Interleukin-β gene (IL-β), and hypoxia-inducible factor gene (HIF). Pharmacogenomics testing aims to provide targeted therapies and interventions that are tailored to the specific characteristics of an individual, optimizing treatment outcomes and minimizing resistance and adverse effects. The article concludes by suggesting the potential of receptor modification to revolutionize treatment outcome of erythropoietin deficiency anemia through integration of the mentioned approach.

Despite concerns about the negative effects of social distancing and prolonged school closures on children’s lifestyle and physical activity (PA) during the COVID-19 pandemic, robust evidence is lacking on the impact of the COVID-19 pandemic on children’s wellbeing and daily life. This study aimed to examine changes in the PA levels, sleep patterns and screen time of school-aged children during the different phases of COVID-19 outbreak in Hong Kong using a repeated cross-sectional design. School students (Grades 1 to 12) were asked to report their daily electronic device usage and to fill in a sleep dairy recording their daily sleep and wake-up time. They were equipped with a PA monitor, Actigraph wGT3X-BT, to obtain objective data on their PA levels and sleep patterns. Students were recruited before the pandemic (Sep 2019 – Jan 2020; n=577), during school closures (Mar 2020 – Apr 2020; n=146), and after schools partially reopened (Oct 2020 – Jul 2021; n=227). Our results indicated lower PA levels, longer sleep duration, and longer screen time among participants recruited during school closures than those recruited before the COVID-19 outbreak. Primary school students were found to sleep on average for an extra hour during school closures. Our findings illustrate the impact of social distancing policies during the COVID-19 pandemic on the sleep pattern, screen time, and PA level in school-aged children in Hong Kong. Professionals should reinforce the importance of maintaining a physically active lifestyle, good sleep hygiene, and healthy use of electronic devices to parents and school-aged children during the COVID-19 Pandemic.

This article focuses on the economic dimensions of maternal health, highlighting the benefits of investing in maternal healthcare and the policy implications for sustainable development. Through a comprehensive review of the literature, the article explores the economic impact of maternal health, including its effects on human capital, productivity, and healthcare costs. It emphasizes the importance of addressing social determinants such as access to healthcare services, education, employment, income, and geographical disparities. By prioritizing maternal health, societies can unlock the economic potential of women, promote inclusive growth, and reduce gender disparities. The article discusses policy interventions, including the importance of healthcare infrastructure, financial support for maternal healthcare, and promoting gender equality. It also emphasizes the need for future research to quantify the economic benefits and evaluate the cost-effectiveness of different interventions. Overall, the article underscores the economic imperative of investing in maternal health and provides valuable insights for policymakers and researchers seeking to enhance maternal health outcomes and promote sustainable economic development.

Objective: We tested a model of individual health literacy information sharing with family members, personal preventive behaviours and family well-being during the Coronavirus Disease 2019 (COVID-19) pandemic in Hong Kong. Methods: We analysed data of 1501 randomly selected Chinese adults from a cross-sectional survey in Hong Kong from 9 to 23 April, 2020. Individual health literacy about COVID-19 with the items extracted from the questionnaire in World Health Organization Risk Communication and Community Engagement (RCCE) Action Plan Guidance for COVID-19 preparedness and response, COVID-19 information sharing with family members, preventive behaviours against COVID-19 and family well-being were measured. Structural equation modelling analysis tested the proposed model. Findings: COVID-19 information sharing with family members partially mediated the association between individual health literacy and personal preventive behaviours. The direct effect of 0.24 was shown, and the indirect effect through COVID-19 information sharing with family members was small at 0.03 (Z = 3.66, p < 0.001). Family well-being was associated with personal preventive behaviours against COVID-19. The model was adjusted for sex, age, and socioeconomic status factors and had good fit with RMSEA = 0.04, CFI = 0.98, TLI = 0.96, and SRMR = 0.02. Conclusion: COVID-19 information sharing with family members was a partial mediator between individual health literacy and personal preventive behaviours against COVID-19. Strategies for enhancing health literacy and preventive measures against COVID-19 are needed to promote family well-being in the pandemic.

Bacterial adhesion to the surface of the adhesive material is an important step in the formation of plaque and enamel demineralization. In order to correlate the material composition to the specific surface roughness of the resin and to the probable more favourable adhesion of bacteria, scanning electron microscopy, combined with focus ion bean micromachining, together with stylus profilometry analysis have been in vitro performed to reveal the structural nature of three orthodontic adhesive resins used for bracket bonding and, above all, to understand how compositional factors can influence specific pivotal properties such as material’s surface roughness and robustness. In particular, we speculated about the morphological features that determine an increase in the bacterial adhesion and we proposed focused ion beam technique as a valuable tool to compare the internal structures of the polymers and to determine the peculiar mechanical properties of the examined adhesive resins.

Obstructive sleep apnea (OSA) may be linked to various factors that narrow the upper airways, such as obesity, adenotonsillar hypertrophy and craniofacial abnormalities. Hypothyroidism has also been described as a risk factor for OSA. However, the implication of goiter independently of thyroid function in the occurrence of OSA remains unclear. We present the case of a 66-year-old patient, with a large compressive multinodular goiter for whom total thyroidectomy was indicated. During the preoperative assessment, the patient showed a body mass index (BMI) of 37.8 kg/m2 with symptoms of OSA. Respiratory polygraphy confirmed the diagnosis of severe OSA (apnea hypopnea index: AHI=32) and treatment with continuous positive airway pressure (CPAP) was initiated prior to thyroid surgery. Surprisingly, after total thyroidectomy, OSA symptoms disappeared and the patient abandoned CPAP therapy. Subsequent respiratory polygraphy after thyroidectomy showed a decrease in AHI to a normal value (AHI < 5). Interestingly, there was no change in BMI or other factors explaining the resolution of OSA, except for thyroidectomy. This case report suggests that goiter can be considered a risk factor for OSA. However, prospective studies are needed to accurately assess the effects of goiter on occurrence of OSA according to its dimensions and local extension.

In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

Background: Diabetes mellitus (DM) and periodontitis are two chronic diseases that are interconnected. The coexistence of these conditions leads to increased severity of periodontitis and challenges in controlling blood glucose levels in diabetic patients. Objectives: The aim of this study was to evaluate both the influence of periodontal disease and its treatment in patients with DM in terms of a reduction in glycosylated hemoglobin levels at 3 and 6 months after treatment. Methods: A sequential, nonprobabilistic, controlled, prospective and longitudinal case−control study was carried out at the University Dental Clinic of the Morales Meseguer Hospital in Murcia, Spain. Thirty diabetic patients were divided into two groups: patients with periodontitis (test group) and patients without periodontitis (control group). The periodontal and endocrine-metabolic variables were measured at baseline and at 3 and 6 months after periodontal treatment for both groups. Results: Statistically significant differences were found at 3 and 6 months after periodontal treatment with respect to HbA1c levels in the group of periodontal patients. However, these differences were not observed in the control group. Conclusion: The presence of periodontal disease increased HbA1c levels in patients with DM. Nonsurgical periodontal treatment significantly decreased the degree of periodontal inflammation and the HbA1c level at 3 and 6 months after treatment.

Quantifying different stocking rates effects in three study areas placed at Mediterranean forest (Cuenca, Spain) was conducted by applying a multiparametric soil quality index, SQI, developed in undisturbed forest soils (> 40 years). The main objective is to advance in the development and application of multiparametric indexes which allow for soil condition assessment. For it, is analyse the effectiveness of a multiparametric soil quality index (SQI) as an indicator livestock impacts on the soil in mediterranean forests. Control areas without stocking rates were compared in forest stands with different age (Thicket forest stand, < 30 years; High polewood forest stand, 30-60 years; Old growth forest stand, > 60 years); with various intensity grazing areas (permanent livestock passage: inactive sheepfold for 2-3 years, and active sheepfold; intermittent livestock passage: bare soil, pine stand, scrubland). The multiparametric soil quality index (SQI) applied sensitive to changes in forest ecosystems depending of different stocking rates. However, for even more preci-sion to assess cattle alteration, multiparameter index recalibrated, creating a new one; Soil Status Index by Livestock (SSIL). Correlation between quality ranges obtained with both indexes in dif-ferent study areas suggest that SSIL can be considered a livestock impact reference indicator in Mediterranean forest soils.

This study delves into the integration of Decentralized Finance (DeFi) within metaverses, probing its implications and potential. It elucidates DeFi protocols and the intricacies of metaverses before inspecting their intersection and the resulting economic prospects. The analysis further appraises inherent risks such as financial volatility, security, and regulatory issues. Case studies provide tangible insights into DeFi applications in metaverses. Future trajectories of DeFi in metaverses are projected, underlining the possible impact on the broader financial sector. This paper contributes to burgeoning research at the nexus of blockchain technology, finance, and virtual reality.

Virtual tours with 360 photos present a quick, easy and accessible way to create immersive experiences. The visualization in diverse devices, provide a user experience that can be different. A virtual tour with 360 photos of the Chapel of Dolores (Tenerife), has been created. Whose access is limited to specific days, so the creation of a virtual tour allows you to visit it at any time, in addition, a pilot test has been carried out with students of the degree of restoration and conservation of cultural heritage in order to measure the user experience of the virtual tour depending on the device used. The participants took a virtual tour of the Dolores Chapel, first with a cell phone and then with the virtual reality headset, and then completed a user experience questionnaire. The results obtained comparing both visualization technologies are detailed, highlighting that when using the virtual reality headset no better results are obtained in the immersion subscale, in addition, the visualization on a Smartphone is more comfortable and obtains better results in consequences such as dizziness and vertigo. Therefore, it may be an interesting strategy to have simple versions that work quickly on the cell phones.

This study focuses on the synthesis, characterization and study of a new perovskite-type materials as cathode in SOFC. The synthesized doped perovskites have been successfully synthesized with high purity. The electrochemical performance of these materials was extensively examined through the characterization of I-V-P and EIS curves at the three temperatures: 750, 800 and 850 °C. Where it is revealing a substantial reduction of total resistances by approximately 50% and 70%, accom-panied by an impressive increase in power densities by around 200% and 300%, respectively. The cell featuring Sm0.01Sr0.99Fe0.5Co0.5O3 exhibited the most commendable electrochemical properties at each temperature, following closely were Pr0.01Sr0.99Fe0.5Co0.5O3 and La0.01Sr0.99Fe0.5Co0.5O3.

It is important for researchers in material domain to reconstruct and visualize the microstructure of alloy, which helps discover morphologies and properties that can only be found in three dimensional and microscopic space. However, because of the limitation of state-of-the-art sensors, the internal microstructure of the material is not easy to obtain. In this paper, a novel automatic 3D reconstruction method is proposed using diffraction contrast tomography technology to capture the 3D microstructure of Al-La alloy. The pipeline of the proposed method starts from the imaging of Al-La alloy with the LabDCT technique from Carl Zeiss AG, which produces a sequence of 2D microstructure sections. Then, a segmentation algorithm based on superpixel and lifted multicut is proposed to extract the 2D microstructure in an image section. Finally, 2D segmentations are joined together to reconstruct and visulize the 3D microstructure. As a result, a novel morphology of Al-La alloy is recovered with both dendrite and lamellar morphologies. The proposed method has the advantage of the ability to losslessly recover the internal microstructure.

Bedbug (Cimex spp.) are a nuisance public-health pest that is on the rise globally, particularly in crowded cities such as Hong Kong. To investigate the health impacts of bedbug infestations among bedbug victims, online surveys were distributed in Hong Kong between June 2019 to July 2020. Data on sociodemographics, self-rated health, average hours of sleep per day, and details of bedbug infestation were collected. Bivariate and multivariable analysis were performed using logistic regression. The survey identified 422 bedbug victims; among them, 223 (52.9%) experienced ≥5 bites in the past month, most bites occurred on the arms (n=202, 47.8%) and legs (n=215, 51%), and the most common reaction to bites were itchiness (n=322, 76.3%), redness, and swelling of the skin (n=246, 58.1%), and difficulties sleeping or restlessness (n=125, 29.6%). Bites usually occurred during sleep (n=230, 54.5%). For impact on daily life in the past month, most bedbug victims reported moderate to severe impact on mental and emotional health (n=223, 52.8%) and sleeping quality (n=239, 56.6%). Lower self-rated health (aOR&lt;1) was independently associated with impact to physical appearance (p=0.008), spending money on medication or doctor consultation (p=0.04), number of bites in the past month (p=0.023), and irregular time of bites (p=0.003). Lower average hours of sleep per day (aOR&lt;1) was independently associated with impact on mental and emotional health (p=0.016). This study brings attention to the neglected issue of bedbug infestation by considering bedbugs as an infectious agent instead of a vector and providing empirical evidence describing its health impacts.

In recent decades, a number of high-profile cases involving fraud as research misconduct have been in the media and resulted in severe consequences for those convicted. According to the increased cases of allegations and coverage in the media, this reflects a heightened awareness that fraudulent actions exist. Nonetheless, the Office of Research Integrity data suggests that despite the growth in the number of the cases of allegation there has not been a commensurate increase in findings of misconduct. The purpose of this paper is to explore misconduct to better understand what it entails. An analysis of misconduct from the perspective of the definitions of allegations and fraud of is conducted and potential frameworks for understanding both are considered. The paper considers serial-positioning effects of primacy and recency on allegation phenomena, as well as supervenience theory and contextualism as a lens for understanding fraud. Discussion of the relational semantics of the core aspects of fraud and de facto grouping of forms of misconduct. It is concluded that the interrogative pronouns of “what” and “when” could be used to categorize forms of misconduct laying the foundation for the next paper that deconstructs the definition of falsification according to the Public Health Service.

Horn manure (Preparation 500) is a product used in the practice of biodynamic agriculture. It is obtained by an underground fermentation of cow faecal material incubated in cow horns for several months. The product is used as spray treatment meant to increase soil fertility. In the present report we analyzed the successional changes in bacterial and fungal communities throughout the process of horn manure maturation by high throughput sequencing of ribosomal 16S (bacterial) and ITS (fungal) gene markers. Marked shifts in the microbial community were seen involving a general decrease from a Firmicutes-dominated material to a product transiently enriched in Proteobacteria and later in Actinobacteria, mostly within the Nocardioidaceae family. In the fungal community evolution, the most abundant taxon in the starting faecal material resulted a member of the Onygenales order, known to specifically degrade keratin. Its abundance in the intestine is explained by the fact that keratin, which is also the structural component of hairs and horns, is found in all epithelial layers, including gut mucosae. This occurrence suggests a link of enzymatic/catabolic nature between manure and horn.

The American Academy of Arts and Sciences suggested the definition of science literacy emphasize how crucial understanding the scientific process and the ability to evaluate conflicting scientific evidence is. The purpose of this article is to present an evidence-supported curriculum covering the fundamentals of logic, reasoning, and argumentation skills to address the emphasized basic knowledge, skills, and abilities required to be scientifically literate, which will prepare the public to understand and engage with science meaningfully. An analytic-synthetic approach toward understanding the notion of public is taken using a theoretical biomimetics framework that identifies naturally occurring objects or phenomena that descriptively captures the essence of a construct to facilitate creative problem-solving. In the present case, the problem being solved is how to reconcile what is meant by public, how it ought to be interpreted, the different levels of confidence in science that exist, and various understandings of science all with one another. The results demonstrate there is an inherent denotative-connotative inconsistency in the traditional notion of public that can be explicated through the concept of a fractal allowing for comprehension of the relationship between public confidence in, and understanding of, science.

Children with Fetal Alcohol Spectrum Disorders (FASD) and Autism Spectrum Disorders (ASD) experience significantly higher rates of sleep disturbances than their typically developing peers. Pre-sleep anxiety and waking emotional content is known to affect the content and frequency of nightmares, which can be distressing to children and caregivers. This is the first study to analyse nightmare frequency and content in FASD, and to assess its association with psychometric outcomes. We assessed reports from 277 caregivers of children with ASD (n=61), FASD (n=112), and TD children (n=104) using the Children’s Sleep Habits Questionnaire (CSHQ), the Child Behavior Checklist (CBCL), the Spence Children’s Anxiety Scale (SCAS) and the Behavior Rating Inventory for Executive Functioning (BRIEF). Within the ASD group, 40.3% of caregivers reported their children had nightmares. Within the FASD group, 73.62% of caregivers reported their children had nightmares and within the TD group, 21.36% of caregivers reported their children had nightmares. Correlation analysis revealed significant associations between anxiety and nightmares, maladaptive behaviour and nightmares, and executive functioning and nightmares in the TD and FASD groups, but not ASD group. This paper adds to the emerging body of work supporting the need for sleep interventions as part of clinical practice with regard to children with ASD and FASD. As a relatively niche but important area of study this warrants much needed further research.

The will and intellect have been debated philosophically without resolution for centuries. It is for this reason that this article considers doctrines of the will and intellect of two 17^th-century rationalist philosophers, Rene Descartes, and Baruch Spinoza, both of whom were chosen as the focus for analysis because of their prominence and contrasting views. Our objective was to critique the doctrine of the will and intellect to develop an alternate theory that expounds on their previous work. A qualitative exploration was undertaken that compared their respective belief systems of Dualism and Monism. Despite the strengths of their arguments, an analysis of Part V of Spinoza’s Ethics and Discourse on Method and Meditations on First Philosophy by Descartes led the author to determine that both were partially correct in their positions yet consistent with one another. From this conclusion and building upon their work, this article presents the synthesis of the author’s alternate theory regarding the qualitative characteristics of both the will and intellect. An ontological argument against the existence of infinite entities as a corollary with the implication that neither the will, intellect, nor God can be infinite. While the limitation of the conclusions drawn is that they are dependent on the author’s philosophical framework, the originality of this paper is based on the author’s synthesis of one coherent theory from two philosophers espousing contrasting theistic systems and should serve as the foundation for future exploration and debate.

We present a cost- and time-efficient method for the controlled preparation of single phase La(IO3)3 nanoparticles via a simple soft-chemical route which takes a matter of hours, thereby providing an alternative to the common hydrothermal method which takes days. Nanoparticles of pure α-La(IO3)3 and pure δ-La(IO3)3 were synthesised via the new method depending on the source of iodate ions, thereby demonstrating the versatility of the synthesis route. The crystal structure, nanoparticle size-dispersal and chemical composition were characterised via angle- and energy-dispersive powder X-ray diffraction, scanning electron microscopy and Fourier-transform infrared spectroscopy.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In EBM process monitoring, data analysis for processed layer quality evaluation is currently focused on the extraction of information from the raw data collected in-EBM process, i.e. thermal/ optical / electronic images, and the comparison between the collected data and the Computed Tomography (CT)/ microscopy images generated post-EBM process. This article postulates that a stack of bitmaps could be generated from the 3D model at a range of Z heights during file preparation of the EBM process, and serve as a reference image set. In-EBM process comparison between that and the workpiece images collected during the EBM process could then be used for quality assessment purposes. In addition, despite the extensive literature on 3D model slicing and contour generation for AM process preparation, no methods regarding image generation from cross sections of the 3D models have been disseminated in details. This article aims to address this by presenting a piece of 3D model-image generation software. The software is capable of generating binary 3D model reference images with user-defined Region-of-Interest (ROI) of the processing area, and Z heights of the model. It is envisaged that this 3D model-reference image generation ability opens up new opportunities in quality assessment for the in-process monitoring of the EBM process.

The insurance sector has undergone a transformative shift with the emergence of Insurtech, integrating technological innovations into the industry. This review aims to provide a comprehensive overview of the impact of Insurtech on the insurance sector, focusing on the case study of Lemonade. By placing the study in the context of the broader insurance landscape, the review explores the significance and relevance of this transformation. The article analyzes Lemonade's unique business model and its departure from traditional insurance practices. Furthermore, it examines the implications of Lemonade's approach on the industry and the challenges it faces. Through this analysis, the review sheds light on how Insurtech and the transformation of the insurance sector are redefining insurance services and consumer experiences. The future implications of these trends for insurance companies, consumers, and the industry as a whole are also explored. In summary, this review provides valuable insights into the transformative power of Insurtech, emphasizing the importance of technological advancements and innovative approaches in shaping the future of the insurance sector.

The implementation of management systems has become a strategic advantage in achieving business goals, especially in industrial organizations, but the implementation of social responsibility requirements is especially ethical. Large multinational companies have long been developing and, in particular, implementing their own codes of conduct, which include their suppliers, to demonstrate their commitment to Corporate Social Responsibility (CSR). The compliance with CSR requirements from stakeholders is thus extended or intertwined with requirements in established management systems (MSs). The objectives of the study were to (1) analyze the different approaches to CSR in internationally recognized cross-industry and industry-specific standards and codes in different industries; (2) select the most appropriate framework for assessing the degree of applicability of CSR in the selected management systems and develop a methodology for its assessment; (3) apply the proposed methodology (referred to as SRIMS) in the selected areas: automotive industry, research organization, and metallurgical industry; (4) through ANOVA, validate its use for assessing the overall level of CSR applicability in an organization's established management systems. The application of the Bonferroni method confirmed the hypotheses that the developed SRIMS model is a sufficiently appropriate tool for assessing the overall level of applicability of CSR requirements to established MSs.

In today's world, news events are emerging incessantly. Classifying the same event reported by different countries is of significant importance for public opinion control and intelligence gathering. Due to the diverse types of news, relying solely on translators would be costly and inefficient, while depending solely on translation systems would incur considerable performance overheads in invoking translation interfaces and storing translated texts. To address this issue, we mainly focus on the clustering problem of cross-lingual news. To be specific, we use a combination of sentence vector representations of news headlines in a mixed semantic space and the topic probability distributions of news content to represent a news article. In the training of cross-lingual models, we employ knowledge distillation techniques to fit two semantic spaces into a mixed semantic space. We abandon traditional static clustering methods like K-Means and AGNES in favor of the incremental clustering algorithm Single-Pass, which we further modify to better suit cross-lingual news clustering scenarios. Our main contributions are as follows: (1) We adopt the English standard BERT as the teacher model and XLM-Roberta as the student model, training a cross-lingual model through knowledge distillation that can represent sentence-level bilingual texts in both Chinese and English. (2) We use the LDA topic model to represent news as a combination of cross-lingual vectors for headlines and topic probability distributions for content, introducing concepts such as topic similarity to address the cross-lingual issue in news content representation. (3) We adapt the Single-Pass clustering algorithm for the news context to make it more applicable. Our optimizations of Single-Pass include adjusting the distance algorithm between samples and clusters, adding cluster merging operations, and incorporating a news time parameter.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

Alzheimer´s disease (AD) is characterized by the brain deposition of senile plaques composed by amyloid-β peptides (Aβ) that increase inflammation. An endogenous peptide derived from the insulin-like growth factor (IGF)-I, glycine-proline-glutamate (GPE) has IGF-I-sensitizing and neuroprotective actions. Here, we examined the effects of GPE on Aβ levels and hippocampal inflammation generated by the intracerebroventricular infusion of Aβ25-35 during 2 weeks (300 pmol/day) in ovariectomized rats and the signaling-related pathways and levels of Aβ-degrading enzymes associated with these GPE-related effects. GPE prevented the Aβ-induced increase in the phosphorylation of p38 mitogen-activated protein kinase and the reduction in activation of signal transducer and activator of transcription 3, insulin receptor substrate-1 and Akt, as well as on interleukin (IL)-2 and IL-13 levels in the hippocampus. The functionality of somatostatin, measured as the percentage of inhibition of adenylate cyclase activity and the levels of insulin-degrading enzyme were also preserved by GPE co-treatment. These findings indicate that GPE co-administration may protect from Aβ insult by changing hippocampal cytokine content and somatostatin functionality through regulation of leptin- and IGF-I-signaling pathways that could influence the reduction in Aβ levels through modulation of levels and/or activity of Aβ proteases.

Abstract: The present work evaluates the feasibility of using volcanic fly ash (VFA), generated by the eruption of the Tajogaite volcano on the island of La Palma (Spain) in 2021, as a precursor in the preparation of cementitious materials with different Portland cement (PC) replacement levels (0%, 30%, 70% and 100%), in the absence (Blended Cement, BC) and presence of an alkaline ac-tivator (Hybrid Alkaline Cement, HAC, and Alkaline Cements, AC). Hydration kinetics (isother-mal conduction calorimetry), paste mechanical strengths and reaction products were character-ised by XRD, FTIR, TG/DTG and BSEM/EDX. The results obtained indicate that the strengths de-veloped by the hybrid alkaline cements (HAC) are higher than those of the blended cements (BC), especially at the age of 2 days, where 25 MPa was obtained with the replacement of 70% PC by VFA. Alkaline cements (AC, 100% VFA) prepared with 8M NaOH solution as activator reached 40 MPa after 2 days. It was observed that in all the binders, depending on the initial composition of the binder mixture and the percentage of replacement and/or activator, VFA reacts to form cementitious gels, C-A-S-H and N-A-S-H type, which supports its use as a mineral addition to blended cement or as a precursor in the preparation of alkaline and hybrid alkaline cements.

The 1,2,3-triazole derivative 2-(4-chlorophenyl)-5-(pyrrolidin-1-yl)-2H-1,2,3-triazole-4-carboxylic acid with potential anticancer activity was used as a ligand in complex formation with the lan-thanum(III) ion. The molecular structure and vibrational spectra of the complex were optimized at three DFT levels and the scaled IR and Raman spectra were compared to the experimental ones. Several scaling procedures were used. Through a detailed analysis, the structure predicted for the newly synthetized La(III) complex was confirmed by the good accordance of the calculat-ed-experimental IR and Raman spectra. The best DFT method appears to be M06-2X with the Lanl2mb basis set, followed closely by Lanl2dz. The effect of the lanthanide atom on the molecular structure and atomic charge distribution of the triazole ring was evaluated. Potential free radical scavenging activity of both, ligand and complex, was investigated in several radical-generating model systems. Potential mechanisms of antioxidant action (hydrogen atom transfer – HAT and single electron transfer - SET) were elucidated.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

Since the 1960s Rare earths (REs) applications gradually have expanded to everyday life. REs have great strategic importance in industrial and technological development, so it is expected an increase in their demand. Among the REs the European Commission considered Cerium and Lanthanum as critical raw materials. This research article studies the adsorption of Ce and La onto two carbon nanomaterials, multiwalled carbon nanotubes (MWCNT) and carboxylic functionalized multiwalled carbon nanotubes (MWCNT_ox). The latter has slightly more affinity for REs than MWCNT. The recovery percentage for Ce were 89 and 98% and in the case of for La were 99 and 92% using 0.8 g of MWCNT and 0.2 g of MWCNT_ox respectively. The adsorption process fits a pseudo second-order kinetic model and the Langmuir isotherm best represented the metal uptake.

Any quantization maps linearly functions on a phase space to symmetric operators in a Hilbert space. Covariant integral quantization combines operator-valued measure with symmetry group of the phase space. Covariant means that the quantization map intertwines classical (geometric operation) and quantum (unitary transformations) symmetries. Integral means that we use all ressources of integral calculus, in order to implement the method when we apply it to singular functions, or distributions, for which the integral calculus is an essential ingredient. In this paper we emphasize the deep connection between Fourier transform and covariant integral quantization when the Weyl-Heisenberg and affine groups are involved. We show with our generalisations of the Wigner-Weyl transform that many properties of the Weyl integral quantization, commonly viewed as optimal, are actually shared by a large family of integral quantizations.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

The Abnormal increase in the mass of adipose tissue during adipogenesis results in obesity. Obesity is a predominant disorder and its widespread has become a critical concern worldwide. This is due to the burden of its associated co-morbidities like cancer, cardiovascular diseases and diabetes. Over-nutrition and the sedentary lifestyle are considered as the most significant causes of abnormal adipose tissue development. Appropriate lifestyle and behavioural interventions are the corner stones of successful weight loss, but to maintain such a lifestyle is highly challenging. Accordingly, natural products from plants either as crude extracts or purified phytochemicals have shown to have anti-obesogenic properties and are generally non-toxic and cost-effective. In this review, we discuss the comparative analysis of molecular mechanisms involved in adipogenesis and the recently reported anti-obesogenic effects of various plant products. We will provide a common platform for understanding obesity and adipogenesis, and a possible mechanism of action for anti-obesogenic plant products through AMP-activated protein kinase (AMPK), which will support the scientific development of traditional herbal medicine.

Background/Aim: Baricitinib (BAR) is the first oral selective Janus kinase inhibitor approved in Europe for rheumatoid arthritis (RA). Real-world data are still needed to clarify its long-term benefit/risk profile. This study aimed to evaluate the effectiveness, persistence, adherence, and safety of BAR in a real-world setting. Methods: An ambispective study was conducted between October 2017 and December 2021 in RA patients starting BAR. Effectiveness was evaluated by change from baseline in the Disease Activity Score using 28-joint counts-C reactive protein (DAS28CRP), and achievement of low disease activity/remission. Drug persistence was evaluated by Kaplan-Meier analysis. Adherence was estimated by medication possession ratio (MPR) and the 5-item Compliance Questionnaire for Rheumatology. Safety was assessed by global incidence proportion and adjusted incidence rates of adverse events. Results: 61/64 recruited patients were finally analyzed, 83.6% female, 78.7% seropositive, mean age of 58.1 (15.4) years, and disease duration of 13.9 (8.3) years. 32.8% were naïve to biologics and 16.4% received BAR on monotherapy. After a median exposure to BAR of 12.4 (6.6-31.2) months (range 3.1-51.4), a significant change in DAS28CRP was observed (difference -1.2, p=0.000). A total of 70.5% and 60.7% patients achieved low disease activity or remission, respectively and 50.8% (31/61) patients remained on BAR during follow-up with a median persistence of 31.2 (9.3-53.1) months. The average MPR was 0.96 (0.08) and all patients were “good adherents” by questionnaire. 21.3% patients discontinued baricitinib due to toxicity. Conclusion: In our real-world practice, BAR demonstrated effectiveness, large persistence, high adherence to treatment and acceptable safety profile.

This paper explores the rationale behind Booker T. Washington’s vocationalist philosophy of education for the then recently emancipated black population. Through the use of a critical thinking framework, an analysis of remarks from key speeches and his life according to scholars providing Washington’s prescriptive argument and rhetoric is undertaken. Despite Washington’s intentions, the argument for his vocational approach is demonstrated to be oppressive, myopic, and circular in its logic. The author proposes a framework for understanding the counterintuitive development of vocationalist philosophy based on the dichotomous nature of the human experience’s value-construct and context misalignment. Concordant or discordant dualities that result from misalignment are explained and how to reconcile Washington’s Vocationalism with opposing the philosophy of W.E.B. Du Bois due to equivalence or consistency of values with theoretical constructs is also discussed.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

Abnormal Tau phosphorylation and aggregation into neuronal paired helical filaments and neurofibrillary tangles cause tauopathies, a class of neurodegenerative diseases, that include Alzheimer’s disease, frontotemporal dementia and parkinsonism linked to chromosome 17, progressive supranuclear palsy, Pick's disease, and corticobasal degeneration. Glycogen synthase kinase-3β (GSK-3β) is the most critical kinase to phosphorylate Tau. We have developed the linoleic acid derivative 8-[2-(2-pentyl-cyclopropylmethyl)-cyclopropyl]-octanoic acid (DCP-LA), with cyclopropane rings instead of cis-double bonds, as an anti-dementia drug. DCP-LA serves as a selective activator of PKCε and a potent inhibitor of protein tyrosine phosphatase 1B (PTP1B). DCP-LA prevents Tau phosphorylation due to PKCε-mediated direct inactivation of GSK-3β, to PKCε/Akt-mediated inactivation of GSK-3β, and to receptor tyrosine kinase-mediated inactivation of GSK-3β in association with PTP1B inhibition. DCP-LA targeting GSK-3β, thus, could become a valid drug for treatment of tauopathies.

Because of an often complicated and difficult-to-access care system, help-seeking for people with suspected dementia can be stressful. Difficulty in help-seeking may contribute to carer burden, in addition to other known stressors in dementia care. This study examined the relationship between perceived help-seeking difficulty and carer burden, and the barriers contributing to perceived difficulty. We interviewed 110 carers accessing a community-based dementia assessment service for suspected dementia of a family member for their perceived difficulty, delays, and barriers in help-seeking, and carers burden in terms of role strain, self-criticism, and negative emotions. Linear regression models showed that perceived help-seeking difficulty is associated with carer self-criticism, while carer role strain and negative emotions are associated with symptom severity of the person with dementia but not help-seeking difficulty. Inadequate knowledge about symptoms, service accessibility, and affordability together explained more than half of the variance in perceived help-seeking difficulty (Nagelkerke R2 = .56). Public awareness about symptoms, support in navigating service, and financial support may reduce perceived difficulty in help-seeking, which in turn may reduce carer self-criticism during the early course of illness.

The application of electrospray ionization mass spectrometry (ESI-MS) as a direct method for detecting reactive intermediates is a technique of developing importance in the routine monitoring of solution-phase reaction pathways. Here, we utilize a novel on-line photolysis ESI-MS approach to detect the photoproducts of riboflavin in aqueous solution under mildly alkaline conditions. Riboflavin is a constituent of many food products, so its breakdown processes are of wide interest. Our on-line photolysis setup allows for solution-phase photolysis to occur within a syringe using UVA LEDs, immediately prior to being introduced into the mass spectrometer via ESI. Gas-phase photofragmentation studies via laser-interfaced mass spectrometry of deprotonated riboflavin, [RFH], the dominant solution-phase species under the conditions of our study, are presented alongside the solution-phase photolysis. The results obtained illustrate the extent to which gas-phase photolysis methods can inform our understanding of the corresponding solution-phase photochemistry. We determine that the solution-phase photofragmentation observed for [RFH] closely mirrors the gas-phase photochemistry, with the m/z 241 ion being the only major condensed-phase photoproduct. Further gas-phase photoproducts are observed at m/z 255, 212, and 145. The value of exploring both the gas- and solution-phase photochemistry to characterize photochemical reactions is discussed.

The recent outbreak of coronavirus disease 2019 caused by the new coronavirus, SARS-CoV-2, has become an international emergency. Since there is no effective therapy for the treatment of this disease, drugs or vaccine that can prevent or cure the SARS-CoV-2 infection are urgently needed. The viral 3-chymotrypsin-like cysteine protease (3CLpro), which plays a key role in the replication of coronavirus, is a potential drug target for the development of anti-SARS-CoV-2 drugs. With the crystal structure of 3CLpro, we performed virtual screening from a small chemical library of a Traditional Chinese Medicine recipe- FuFang Zhenzhu Tiaozhi (FTZ). Five compounds with the best scores were screened and could be considered as potential hit compounds to be investigated further with bioassays for their anti-virus effects.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.

One new La (III) based coordination polymer , namely, [La(1,4-bdc)(H2O)].(H2O) (1) (tpa = terephthalic acid) has been synthesized through the solvothermal synthesis using terephthalic acid. Structural analysis reveals that compound 1 has a 3-D network with a cube topology. The solid state photolumienescence study shows that compound 1 has a strong emission peak at 680 nm upon excitation at 220 nm . The emission peak is characteristic of the red light emission in the visible region of the electromagnetic spectrum.

If students do not fully apply themselves, then they may be considered responsible for the result of being inadequately prepared. +- Nevertheless, student outcomes are more likely to reflect a combination of both effort and systematic problems with overall course architecture. Deficiencies in course design result in inadequate preparation that adversely and directly impacts students’ productivity upon entering the workforce. Such an impact negatively influences students' ability to maintain gainful employment and provide for their families, which inevitably contributes to the development of issues concerning their psychological well-being. It is well-documented that incorporating active learning strategies in course design and delivery can enhance student learning outcomes. Despite the benefit of implementing active learning techniques, rarely in the real world will it be possible for techniques to be used in isolation of one another. Therefore, the purpose of this proposed study is to determine the interactive effects of two active learning strategies because, at a minimum, technique-pairs more accurately represent the application of active learning in the natural educational setting. There is a paucity of evidence in the literature directed toward investigating the interactive effects of multiple active learning techniques that this study is aimed at filling. The significance of this research is that, by determining the interactive effects of paired active learning strategies, other research studies on the beneficial effects of using particular active learning technique-pairs will be documented contributing to the literature so that ultimately classroom instruction may be customized according to the determination of optimal sequencing of strategy-pairs for particular courses, subjects, and desired outcomes that maximize student learning.

Currently, the textile industry is a poorly automated sector, due in part to problems in the handling of deformable leather and textile parts during production operations. In this work, several problems in the handling process of leather and textile parts are addressed, introducing methods to increase the automation of the process. A pneumatic actuator designed to pick up textile or leather parts avoiding their deformation during transport has been developed. This actuator maximizes the number of gripping points to improve handling, making it more stable and efficient. Additionally, a vision system has been implemented in the part picking task which, in conjunction with the CAD information of the part, sends the modified gripping position of the part to the robot. This allows customized handling of each textile or leather part. Finally, validation tests have been carried out on this development, both in simulations and in laboratory conditions, demonstrating its viability and direct applicability in the production line.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

Genetic diversity is the foundation of evolutionary resilience, adaptive potential, and the flourishing vitality of living organisms, serving as the cornerstone for robust ecosystems and the continuous evolution of life on Earth. The landscape of directed evolution, a powerful biotechnological tool inspired by natural evolutionary processes, has undergone a transformative shift propelled by innovative strategies for generating genetic diversity. This shift is fuelled by several factors, encompassing the utilization of advanced toolkits like CRISPR-Cas and base editors, enhanced comprehension of biological mechanisms, cost-effective custom oligo pool synthesis, and the seamless integration of artificial intelligence and automation. This comprehensive review looks into the myriad methodologies employed for constructing gene libraries, both in vitro and in vivo, categorized into three major classes: random mutagenesis, focused mutagenesis, and DNA recombination. The objectives of this review are threefold: firstly, to present a panoramic overview of recent advances in genetic diversity creation, secondly, to inspire novel ideas for further innovation in the genetic diversity generation, and thirdly, to provide a valuable resource for individuals entering the field of directed evolution.