Obtaining a proper position for THA’s components is a crucial aspect for the implant perfor-mance and consequently patient outcomes. Patient specific kinematic seems to be a key factor to reach the optimal implant positioning. The aim of this study was to assess the accuracy and safety of a computed dynamic analysis system which through patient specific guides tries to improve implant positioning and functional orientation according to patient’s spinopelvic mobility and anatomy.A total of 100 consecutive patients were prospectively enrolled. All patients received an OPS dynamic hip preoperative planning. A TC scan protocol follow up analysis has done at 6 month after surgery.The mean deviation from the planned acetabular inclination and anteversion was 4.3° e 3.8° respectively. The 98% of cases was within +/- 10° of Lewinnek safe zone both for inclination and anterversion. The height of osteotomy deviated on the average of 1.6mm. The 100% cases were included within 4mm of osteotomy. Patient specific and laser guided instru-mentation is safe and accurately reproduce the dynamic planning in terms of components orien-tation, osteotomy level, leg length and offset.

“De-[Constructing] Growth” is offered as a deeper and more useful conceptualization that avoids the negative connotations of, and resistance to, “degrowth” by decoupling profit from unsustainable consumption, production, and inequality.

Different alcoholic beverages can have different effects on blood alcohol concentrations (BAC) and neurotoxicity even if equalized for alcohol content by volume. Anecdotal evidence suggested that natural wine is metabolized differently from conventional wines. This triple-blind study compared the BAC of 55 healthy male subjects after consuming the equivalent of 2 units of alcohol of a natural or conventional wine over 3 mins in two separate sessions one week apart. BAC was measured using a professional breathalyzer every 20 mins after consumption for 2 hrs. The BAC curves in response to the two wines diverged significantly at twenty minutes, at forty minutes and also at their maximum concentrations (peaks), with the natural wine inducing a lower BAC than the conventional wine (T20 0.40 vs. 0.46 [p<0.0002], T40 0.49 vs. 0.53 [p<0.0015], peak 0.52 vs. 0.56 [p<0.0002]). These differences are likely related to the development of different amino acids and antioxidants in the two wines during their production. This in turn may affect the kinetics of alcohol absorption and metabolism. Other contributing factors may also include pesticide residues, differences in dry extract content and the use of indigenous or selected yeasts. Further studies are needed to fully understand why natural wines are metabolized differently from conventional wines.

Skin cancer is a disease that reflects most malignant neoplasms worldwide, whose rate of involvement has increased significantly in recent decades. Treatments that offer efficient results with attenuation of adverse reactions and greater patient compliance have been the subject of many systematic investigations. This review aims to qualitatively present published works that showed new strategies to increase the penetration power of natural substances through the skin in the topical treatment against skin cancer. In this sense, nanoengineering mechanisms, the iontophoresis technique, and photodynamic therapy using natural products (NP) contribute to new knowledge about substance carrier strategies in topical treatments against skin cancer.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

In this paper we establish information theoretical bridges between 1) Thermal Heisenberg uncertainties $\Delta x \Delta p$ (at temperature $T$), and 2) LMC structural quantifiers. After having achieved such purpose, we determine to what an extent our bridges can be extended to both the semi classical and classical realms. Also, we find a strict bound relating a special LMC structural quantifier to quantum uncertainties.

Introduction: Due to the great development of digital technology, through CAD (Computer - Aided Design) and CAM (Computer - Aided Manufacturing) systems, digital models could be used in orthodontic treatment planning decision-making, as there are numerous studies in the literature that support the validity of measurements of digital models of anterior teeth and the total coefficient of Bolton analysis. The aim of the study was to compare the average length value of the current upper and lower arches with that of a hypothetical nickel-titanium wire and the accuracy of the Bolton index measurement. In the present study, 138 dental casts were analyzed using Ortho3Shape software. Using the Ortho3Shape software, it was possible to measure the real and ideal lower arch lengths and, with regard to Bolton analysis, the values of the anterior and total Bolton coefficients. By comparing the values obtained with those of the study by A. Anand Kumar et al. using CBCT and plaster casts, the reliability of the measurements obtained with such CAD/CAM orthodontic software was evaluated. Considering the validity of digital measurements demonstrated by the studies and systematic reviews in the literature, it can be stated that CAD/CAM digital models can be a viable alternative to plaster models in the coming years, as they can facilitate model preservation and retrieval. For future studies and research, it would be preferable to use intra-oral scanners (IOS) in order to ensure greater accuracy, requiring only one step and ensuring a better outcome for the patient.

The mutualistic interactions between the oleaginous yeast Lipomyces starkeyi and the green mi-croalga Chloroidium saccharophilum in mixed cultures were investigated to exploit possible syner-gistic effects. As a matter of facts, microalga could act as an oxygen generator for the yeast, while the yeast could provide carbon dioxide to microalga. A lignocellulosic hydrolysate from steam exploded Arundo donax (Giant reed) was used as low cost feedstock. The overall lipid content and lipid productivity obtained in the mixed culture treating the hydrolysate of Arundo donax were equal to 0.081 glipid.gbiomass-1 and 37.2 mglipid.L-1.d-1, respectively. They represented promising re-sults if compared to the model systems where synthetic media were used. This study provided new input for the integration of Single Cell Oil (SCO) production with agro-industrial feedstock and the fatty acid distribution mainly consisting of stearic (C18:0) and oleic acid (C18:1) allows promising applications in biofuels, cosmetics, food additives and other products of industrial interest.

(1) Background/Objectives: Accurate determination of chronological age is crucial in legal dental identification. This study aimed to compare the effectiveness of different formulas in estimating the age of a Brazilian subpopulation by analyzing the pulp/tooth ratio of the maxillary canine and mandibular second premolar in panoramic and periapical radiographs. (2) Methods: The sample consisted of panoramic and periapical radiographs of 247 individuals. The file of each radiograph was opened in the Adobe Photoshop CS4® program to outline and obtain values in pixels for calculating the pulp/tooth ratio. Statistical analysis was conducted using the SPSS program, with a significance level set at 5%. (3) Results: The interclass correlation coefficient demonstrated excellent intra-observer agreement (0.990 – 0.999). The determination coefficients (R2) suggested that only 30-35% of the actual age results could be explained by the pulp/tooth ratio. Smallest differences were observed with Cameriere's formula for the mandibular second premolar on panoramic radiographs (+4.1 years). The greatest differences were found with the formulas for the mandibular second premolar in panoramic radiographs of the Korean (+12.5 years) and Portuguese (-12.1 years) populations. (4) Conclusions: The equations employed allowed for estimating the age of a Brazilian subpopulation and showed little agreement between the actual age and the estimated age.

Reggio Calabria province (South Italy) is known for being almost the only area of cultivation of the bergamot fruit, grown principally for its essential oil, but today much studied for the health benefits of its juice. The biometrics and physico-chemical properties of the three (Citrus bergamia Risso) existing genotypes namely Castagnaro, Fantastico and Femminello were studied during fruit ripening from October to March. Castagnaro cv had the biggest and heaviest fruit during this harvest period. °Brix (7.9-10.0), pH (2.2-2.8) and Formol number (1.47-2.37 mL NaOH 0.1N/100mL) were shown to be influenced by both the genotype and by the harvest date. Titratable acidity (34.98-59.50 g/L) and Vitamin C (Ascorbic acid) (341-867 g/L) decreased during fruit ripening. The evolution of flavonoids such as neoeriocitrin, naringin, neohesperidin brutieridin and melitidin was studied both in bergamot juice and in the bergamot cloudy which is the aqueous extract of bergamot during fruit processing. Bergamot cloudy contained a higher quantity of flavonoids compared to the juice. This study gives important information regarding the cultivar and the harvest date for producers who want to obtain the highest juice quantity or the highest juice quality from the bergamot fruit.

Despite the efforts made to stop the tuberculosis (TB) epidemic, it still remains one of the leading causes of death from an infectious disease. Previous work in the group uncovered a new family of amides which showed promising activities against Mycobacterium tuberculosis. A closer look at the literature showed that these compounds are structurally related to the DNB family of DprE1 inhibitors, so, we decided to study a wide range of substituted amides and determine their activity, focusing on unexplored structures related to the dinitrobenzamides (DNB) found in the literature. To synthesize our library of compounds we started from 3,5-dinitrobenzoic acid to form the nitroaromatic core that is characteristic of the DNB’s, to which we then added linear or cyclic amine moieties. Additionally, the impact of terminal aromatic moieties was also assessed for some derivatives, via an ether, ester, or amide bond. In order to obtain the desired derivatives, multiple synthetic approaches were used, mainly focused on nucleophilic addition/elimination reactions, SN2 reactions and Mitsunobu reactions. The activity was impacted mainly by two structural features, the addition of an aromatic moiety as a terminal group and the type of the linker. The most interesting compounds exhibited activities comparable to isoniazid and DNB1. Computational studies were also performed aimed at understanding their possible interactions with DprE1. The most active compounds are a good starting point for further development, and we plan to study an extended family of compounds based in those structures.

An explanation of the origin of dark matter is suggested in this work. The argument is based on symmetry considerations about the concept of mass. In the Wigner's view, the rest mass and the spin of a free elementary particle in flat space-time are the two invariants that characterize the associated unitary irreducible representation of the Poincar\'e group. The Poincar\'e group has two and only two deformations with maximal symmetry. They describe respectively the de Sitter (dS) and Anti de Sitter (AdS) kinematic symmetries. Analogously to their shared flat space-time limit, two invariants, spin and energy scale for de Sitter and rest energy for Anti de Sitter, characterize the unitary irreducible representation associated with dS and AdS elementary systems. While the dS energy scale is a simple deformation of the Poincaré rest energy and so has a purely mass nature, AdS rest energy is the sum of a purely mass component and a kind of zero-point energy derived from the curvature. An analysis based on recent estimates on the chemical freeze-out temperature marking in Early Universe the phase transition quark-gluon plasma epoch to the hadron epoch supports the guess that dark matter energy might originate from an effective AdS curvature energy.

The electronic structure of 7/9-AGNR superlattices with up to eight unit cells has been studied by means of state of the art Density Functional Theory (DFT) and also by two model Hamiltonians, the first one including only local interactions (Hubbard model, Hu) while the second one is extended to allow long-range Coulomb interactions (Pariser, Parr and Pople model, PPP). Both are solved within mean field approximation. At this approximation level, our calculations show that 7/9 interfaces are better described by spin non-polarized solutions than by spin-polarized wavefunctions. Consequently, both Hu and PPP Hamiltonians lead to electronic structures characterized by a gap at the Fermi level that diminishes as the size of the system increases. DFT results show similar trends although a detailed analysis of the density of states around the Fermi level shows quantitative differences with both Hu and PPP models. Before improving model Hamiltonians, we interpret the electronic structure obtained by DFT in terms of bands of topological states: topological states localized at the system edges and extended bulk topological states which interact between them due to the long-range Coulomb terms of Hamiltonian. After careful analysis of the interaction among topological sates, we find that the discrepancy between ab initio and model Hamiltonians can be resolved considering a screened long-range interaction that is implemented adding an exponential cutoff to the interaction term of PPP model. In this way, an adjusted cutoff distance λ = 2 allows a good recovery of DFT results. In view of this, we conclude that the correct description of the density of states around the Fermi level (Dirac point) needs the inclusion of long-range interactions well beyond Hubbard model but not completely unscreened as is the case for the PPP model.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

The aim of the present study was to investigate the acute effect of caffeine supplementation on performance in official soccer matches. In double-blind, randomized crossover design, 13 professional soccer players performed two complete matches, with Caffeine (CAF) (6 mg/kg) and placebo (PLA) supplementation. Two-way repeated measures ANOVA showed that there was no effect of supplementation on the total distance covered (p = 0.536; ŋp² =0.033) or the total distance covered at different speeds (p = 0.453; ŋp² = 0.048), acceleration or deceleration (p = 0.387; ŋp² = 0.063) number of sprints (p = 0.521; µ² = 0.035) Heart Rate mean (p = 0.484; ŋp² = 0.042) Heart Rate maximum (p = 0.110; ŋp² = 0.199), Rate Perceived Effort (p = 0.151) or efficiency index (p = 0.480). Therefore, acute caffeine supplementation not effective to increase the performance of soccer players in official matches.

in the following article I analyze the trend of cultural and creative employment in the Italian regions between 2004 and 2022 through the use of ISTAT-BES data. After presenting a static analysis, I also present the results of the clustering analysis aimed at identifying groupings between Italian regions. Subsequently, an econometric model is proposed for estimating the value of cultural and creative employment in the Italian regions. Finally, I compare various machine learning models for predicting the value of cultural and creative employment. The results are critically discussed through an economic policy analysis.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

As a form of protection, a nature park is often created to protect and valorise natural and cultural heritage in peripheral rural areas. However, in terms of multi-functionality, new nature parks are incorporated into traditional productive activities, such as recreational and tourist activities, which sometimes compromise sustainability. The research objective is to study the relationship between tourism and sustainability in the Nature Parks of “Sierra de Aracena y Picos de Aroche”, “Sierra Norte de Sevilla” and “Sierra de Hornachuelos” that makes up the Dehesas de Sierra Morena Biosphere Reserve in Andalusia, Spain. Therefore, selective interviews have been carried out with the stakeholders to establish their perception of sustainable tourism and the presence of dominant discourses. The main conclusions indicate (1) the presence of different dominant discourses on sustainability, namely the conservationist and mercantilist ones, with the prevalence of the economic dimension; (2) poor awareness and adaptation to the context of global change; and (3) the presence of competitive relationships that generate difficulties for the governance of sustainable tourism.

Today's city needs more than ever methodological devices that ensure a specific urbanism, in keeping with the complexity of relationships that occur in the urban space. Networks or systems of diverse nature must be activated to achieve a certain success of the city, even more so in its fragile central fabrics. The study is focused on the historic neighborhoods of the city of Jaén (Spain), which have a high vulnerability index. The aim is to establish a strategy to revitalize their urban and social capital and improve their articulation with the rest of the urban and territorial structure. A methodological proposal for the analysis of vulnerability factors and an urban and cartographic analysis of the public space is addressed through an interweaving of a triple network: environmental, social, and urban. For this purpose, the configuration of this overlapping network of analysis and formulation of criteria is presented, which considers the urban multiplicity and promotes new dynamics for the integrated urban regeneration of the area and for the activation of public and collective urban spaces.

French Guiana, located in the Guiana Shield, is a natural reservoir for many zoonotic pathogens that are of considerable medical or veterinary importance. Until now, there are few data available on the description of parasites circulating in this area, especially on protozoan belonging to the phy-lum Apicomplexa; conversely, the neighbouring countries describe a high parasitic prevalence in animals and humans. Epidemiological surveillance is necessary, as new potentially virulent strains may emerge from these forest ecosystems, such as Amazonian toxoplasmosis. However, there is no standard tool for detecting protozoa in wildlife. In this study, we developed Meat-Borne-Parasite, a high-throughput meta-barcoding workflow for detecting Apicomplexa based on Oxford Nanopore Technologies sequencing platform using the 18S gene of fourteen Apicomplexa-positive samples collected in French Guiana. Sequencing reads were then analysed with MetONTIIME pipeline. Thanks to a scoring rule, we were able to classify as Apicom-plexa-positive 10 samples out of 14 and reveal the presence of co-carriages. The same samples were also sequenced with Illumina platform, for validation purposes. On samples identified as Apicomplexa-positive by both platforms, a strong positive correlation at up to genus level was reported. Overall, the presented workflow represents a reliable method for Apicomplexa detec-tion, which may pave the way for more comprehensive biomonitoring of zoonotic pathogens.

We discuss the consequences of the unique symmetry of the de Sitter spacetime. This symmetry leads to the specific thermodynamic properties of the de Sitter vacuum, which produces the thermal bath for matter. The de Sitter spacetime is invariant under the modified translations, ${\bf r}\rightarrow {\bf r} -e^{Ht}{\bf a}$, where $H$ is the Hubble parameter. For $H\rightarrow 0$, this symmetry corresponds to the conventional invariance of Minkowski spacetime under translations ${\bf r}\rightarrow {\bf r} -{\bf a}$. Due to this symmetry, all the comoving observers at any point of the de Sitter space perceive the de Sitter environment as the thermal bath with temperature $T=H/\pi$, which is twice larger than the Gibbons-Hawking temperature of the cosmological horizon. This temperature does not violate the de Sitter symmetry, and thus does not require the preferred reference frame, as distinct from thermal state of matter, which violates the de Sitter symmetry. This leads to the heat exchange between gravity and matter, and to instability of de Sitter state towards the creation of matter, its further heating, and finally to the decay of the de Sitter state. The temperature $T=H/\pi$ determines different processes in the de Sitter environment, which are not possible in the Minkowski vacuum, such as the process of ionization of an atom in the de Sitter environment. This temperature also determines the local entropy of the de Sitter vacuum state, and this allows us to calculate the total entropy inside the cosmological horizon. The result reproduces the Gibbons-Hawking area law, which is related to the cosmological horizon, $S_{\rm hor}=4\pi KA$, where $K=1/16\pi G$. This supports the holographic properties of the cosmological event horizon. We extend the consideration of the local thermodynamics of the de Sitter state using the $f({\cal R})$ gravity. In this thermodynamics, the Ricci scalar curvature ${\cal R}$ and the effective gravitational coupling, $K$, are thermodynamically conjugate variables. The holographic connection between the bulk entropy of the Hubble volume, and the surface entropy of the cosmological horizon remains the same, but with the gravitational coupling $K=df/d{\cal R}$. Such connection takes place only in the $3+1$ spacetime, where there is the special symmetry due to which the variables $K$ and ${\cal R}$ have the same dimensionality. We also consider the lessons from the de Sitter symmetry for the thermodynamics of black and white holes.

In this article, we analyse the determinants of Regulatory Quality-RQ for 193 countries in the period 2011-2020. We use a database from ESG-Environment Social Governance of the World Bank. We apply OLS, Panel Data with Fixed Effects and Panel Data with Random Effects. We found that the variables that have the most positive impact on RQ, among others, are “GHG Net Emission”, “Mean Drought Index”, and “Heat Index”. We also found that the variables that have the most negative impact on RQ are among others “Renewable Energy Consumption”, “Voice and Accountability” and “Rule of Law”. Furthermore, we have applied the k-Means algorithm optimized with the Elbow Method and we find the presence of five clusters. In adjunct, we confront eight machine learning algorithms to predict the value of RQ and we found that the best predictor is Polynomial Regression. The predictive level of RQ for the analysed countries is expected to diminish of -1,29%. In the end, we present a network analysis with the Euclidean distance and we found the presence of a structure of seven networks using augmented data.

We show that the van der Waals gas does not exhibit just the celebrated liquid-gas 1 transition but also a quantum-classical one. We study the issue with reference to the LMC statistical 2 complexity and in relation to the order-disorder contrast.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Recurrent pregnancy loss (RPL) affects around 2 % of women of reproductive age. Primary RPL is defined by ≥2 pregnancy losses and no normal birth delivery. In secondary RPL, the losses are after a normal pregnancy and delivery. Most cases have no clear aetiology, although primary cases are the most complex. Several gene polymorphisms have been associated with RPL. Some polymorphisms are increased in women of Asian or Caucasian race. In admixed RPL populations, the information on possible genetic links is scarce and contradictory. The study aimed to assess the frequency of two SNP in different enzymes involved in medical conditions observed during pregnancy. Microsomal epoxy hydrolase (mEPH) is involved in detoxifying xenobiotics. It is present in ovaries, and it is hormonally regulated. The endothelial nitric oxide synthase forms nitric oxide from arginine and is involved in vascular tone. Two SNPs, rs1051740 and rs1799983, were assessed. The study included 26 controls and 63 primary RPL patients. Significant differences were observed in the frequencies of both SNP (p<0.05). The frequency of mutated alleles was higher in patients. Double mutated homozygotes were encountered only in RLP patients (p<0.05). Genetic polymorphisms rs1051740 and rs1799983 may be involved in primary RPL in the Venezuelan admix population. Genetic studies could provide crucial information on the aetiology of primary RPL.

In this article, I estimate the value of “Individual Using Internet”-IUI in the context of Environmental, Social and Governance-ESG database of the World Bank. I use data from 193 countries for the period 2011-2020. I found that among others the value of IUI is positively associated to “Methane Emissions” and “People Using Safely Managed Sanitation Services” and negatively associated among others to “Fossil Fuel Energy Consumption” and “Renewable Energy Consumption”. I apply the k-Means algorithm for the clusterization optimized with the Elbow Method and we find the presence of three clusters. Finally, I confront eight machine-learning algorithms to predict the future value of IUI. I found that the best predictive algorithm is Linear Regression and that the value of IUI is expected to decrease on average of 0.30% for the analysed countries.

There is an increasing interest in biomarkers of nitric oxide dysregulation and oxidative stress to guide management and identify new therapeutic targets in patients with chronic obstructive pulmonary disease (COPD). We conducted a systematic review and meta-analysis of the association between circulating metabolites within the arginine (arginine, citrulline, ornithine, asymmetric, ADMA, and symmetric, SDMA dimethylarginine), transsulfuration (methionine, homocysteine, and cysteine) and folic acid (folic acid, vitamin B6, and vitamin B12) metabolic pathways and COPD. We searched electronic databases from inception to 30 June 2023 and assessed the risk of bias and the certainty of evidence. In 21 eligible studies, compared to healthy controls, patients with stable COPD had significantly lower methionine (standardized mean difference, SMD=-0.50, 95% CI -0.95 to -0.05, p=0.029) and folic acid (SMD=-0.37, 95% CI -0.65 to -0.09, p=0.009), and higher homocysteine (SMD=0.78, 95% CI 0.48 to 1.07, p˂0.001) and cysteine concentrations (SMD=0.34, 95% CI 0.02 to 0.66, p=0.038). Additionally, COPD was associated with significantly higher ADMA (SMD=1.27, 95% CI 0.08 to 2.46, p=0.037), SDMA (SMD=3.94, 95% CI 0.79 to 7.08, p=0.014), and ornithine concentrations (SMD=0.67, 95% CI 0.13 to 1.22, p=0.015). In subgroup analysis, the SMD of homocysteine was significantly associated with the biological matrix assessed and the forced expiratory volume in the first second to forced vital capacity ratio, but not with age, study location, or analytical method used. Our study suggests the presence of significant alterations in metabolites within the arginine, transsulfuration, and folic acid pathways which can be useful for assessing nitric oxide dysregulation and oxidative stress and identifying novel treatment targets in COPD. (PROSPERO registration number: CRD42023448036)

Beaches are among the habitats most frequented by migratory birds for breeding and/or wintering. However, threats such as human pressure and sea level rise can reduce the availability of these habitats for different species. The presence of alternative areas, such as salt pans and brackish habitats, is essential for many migratory shorebird populations. This study addresses the post-breeding dispersal of the Kentish plover (Charadrius alexandrinus) in the Iberian Peninsula by analysing C and N isotopes in feathers. The study was conducted at six locations along the Iberian coast, which were categorized in three areas: NW Atlantic coast, the Atlantic coast of Andalusia and the Mediterranean coast. Although linear mixed models did not reveal any significant effects of sex or coastal area on isotopic levels, the variability in the data suggests different habitat-use strategies in the post-reproductive period. Birds from the northwest of the Iberian Peninsula exhibit greater fidelity to a single habitat type, i.e. coastal beaches, while populations from the Mediterranean coast and the Atlantic coast of Andalusia show different individual dispersal strategies, occupying coastal habitats and freshwater wetlands. The lack of alternative habitats for the northwest Iberian population, the reduction in available habitat due to rising sea levels and human pressure together pose a serious threat to the survival of this species, already with an unfavourable conservation status.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

We estimate the value of Research and Development Expenditures as a percentage of GDP-RDE in the context of Environmental, Social and Governance-ESG model. We use the ESG World Bank database. We analyze data from193 countries in the period 2011-2020. We apply a set of econometric techniques i.e. Pooled Ordinary Least Squares-OLS, Panel Data with Random Effects, Panel Data with Fixed Effects, Weighted Least Squares-WLS. We found that the level of RDE is positively associated, among others, to “Nitrous Oxide Emissions” and “Scientific and Technical Journal Articles”, and negatively associated, among others to “Heat Index 35”, “Maximum 5-day Rainfall”. Furthermore, we perform a cluster analysis with the application of the k-Means algorithm optimized with the Elbow Method. The results show the presence of four clusters. Finally, we confront eight different machine-learning algorithms to predict the future value of RDE. We find that Linear Regression is the best predictive algorithms. RDE is expected to growth on average of 0.07% for the analysed countries.

Wearable Biosensor Technology (WBT) has emerged as a transformative tool in the educational system over the past decade. This systematic review encompasses a comprehensive analysis of WBT utilization in educational settings over a 10-year span (2012-2022), highlighting both the evolution of this field and its integration to address challenges in education by integrating technology to solve specific educational challenges, such as enhancing student engagement, monitoring stress and cognitive load, improving learning experiences, and providing real-time feedback for both students and educators. By exploring these aspects, the review sheds light on the potential implications of WBT for the future of learning. A rigorous and systematic search of major academic databases, including Google Scholar and Scopus, was conducted in accordance with PRISMA guidelines. Relevant studies were selected based on predefined inclusion and exclusion criteria. The articles selected were assessed for methodological quality and bias using established tools. The process of data extraction and synthesis followed a structured framework. Key findings include the shift from theoretical exploration to practical implementation with the EEG being the predominant measurement, aiming to explore mental states, physiological constructs, and teaching effectiveness. Wearable biosensors are significantly impacting the educational field, serving as an important resource for educators and a tool for students. Their application has the potential to transform and optimize academic practices through sensors that capture biometric data, enabling the implementation of metrics and models to understand the development and performance of students and professors in an academic environment, as well as to gain insights into the learning process.

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) &gt; MRI (2.14 ± 0.08) &gt; EEG (1.87 ± 0.09) &gt; SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) &gt; MRI (0.518) &gt; EEG (0.446) &gt; SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) &gt; MRI (2.558) &gt; EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

In Mexico viticulture represents the second source of employment in the agricultural area after the fruit and vegetable sector. In developed countries, remote sensing is widely used for vineyard monitoring, however, this tool is barely used in developing countries of Iberoamerica. In this re-search, our overall objective is to characterize two vineyards in the state of Queretaro (Mexico) using Sentinel-2 and meteorological data, specifically spectral and thermal indices. Results showed that spectral indices obtained from Sentinel-2 bands have characterized adequately the phenolog-ical evolution of the different varieties of the vineyards. The Modified Soil-Adjusted Vegetation Index (MSAVI) was adequately used to discriminate the first stages of vineyards, while the Nor-malized Difference Vegetation Index (NDVI) was useful to monitor vineyards during the rest stages of vineyards. Thermal indices have shown that the best grape varieties were those that can adapt to both cooler and warmer temperatures, have a reasonable ripening period, and can produce wines with balanced acidity and flavors. In conclusion, the combination of meteorological (including thermal indices) and remote sensing data (NDVI and MSAVI) provide information for choosing the suitable grape variety for this region.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

Proteins play a pivotal role in supporting athletes by promoting muscle hypertrophy and minimizing protein catabolism during exercise. They stimulate muscle protein synthesis, aiding in the repair of exercise-induced muscle damage and serving as an energy source, particularly for post-exercise glycogen replenishment. In individuals with phenylketonuria (PKU), for whom protein intake is limited to essential phenylalanine (Phe), supplementation with Phe-free amino acids or glycomacropeptides is necessary. Tailored for macronutrient and micronutrient content, these protein substitutes fulfill most protein requirements, but lack Phe, unlike dietary sources of protein. Protein requirements for athletes with PKU exceed general recommendations due to limited availability in supplements and potential catabolism mitigation. Various factors influence tolerated dietary Phe in PKU, including protein substitute quantity, distribution, pharmacological treatment, age, growth rate, pregnancy, catabolic states, and physical activity. While general protein requirements for PKU surpass those of the general population, adherence to supplement regimens is crucial for athletes and patients with PKU. Strategically timed protein substitutes enhance muscle protein synthesis, body composition, and sports performance within safety limits. Individualized intake is essential for optimal outcomes, as proteins have a multifaceted role in optimizing athletic performance and addressing challenges in PKU.

A review of quantitative risk assessment (QRA) models of L. monocytogenes in produce was carried out, with the objective of appraising and contrasting the effectiveness of the control strategies placed along the food chains. Despite nine of the thirteen QRA models recovered focused on fresh or RTE leafy greens, none of them represented important factors or sources of contamination in the primary production, such as type of cultivation, water, fertilisers or irrigation method/practices. Cross-contamination at processing and during consumer’s handling was modelled using transfer rates, which were shown to moderately drive the final risk of listeriosis; highlighting therefore the importance of accurately representing the transfer coefficient parameters. Many QRA models coincided in the fact that temperature fluctuations at retail or temperature abuse at home were key factors contributing to increasing the risk of listeriosis. In addition to a primary module that could help assess current on-farm practices and potential control measures, future QRA models for minimally-processed produce should also contain a refined sanitisation module able to estimate the effectiveness of various sanitisers as a function of type, concentration and exposure time. Finally, L. monocytogenes growth in the products down the supply chain should be estimated by using realistic time-temperature trajectories, and validated microbial kinetic parameters, both of them currently available in the literature.

This paper reviews the current knowledge of pepper anthracnose in the Philippines. We present research outputs on pepper anthracnose from the last three years. Then, we present evidence of the widespread occurrence of C. acutatum sensu lato in the Philippines. Finally, we highlight some research prospects that would contribute towards developing an integrated anthracnose management program.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

The current treatment for cervico-facial cancer involves radio and/or chemotherapy. Unfortunately, cancer therapies can lead to local and systemic complications such as mucositis, which is the most common dose-dependent complication in the oral cavity and gastrointestinal tract. Mucositis can cause a considerably reduced quality of life in cancer patients already suffering from physical and psychological exhaustion. However, melatonin, whose role in the treatment of mucositis has recently been investigated, offers an effective alternative therapy in the prevention and/or management of radio and/or chemotherapy-induced mucositis. This review focuses on the pathobiology and management of mucositis in order to improve the quality of cancer patients’ lives.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Members of the genus Armillaria are widespread forest pathogens against which effective protection has not yet been developed. Due to their longevity and the creation of large-scale cloning of Armillaria individuals, the use of mycoviruses as biocontrol agents (BCAs) against these pathogens could be an effective alternative. This work describes the screening of double-stranded RNA banding patterns as a first approach for potential virus discovery and the use of stranded total RNA-seq for viral detection and characterization in Armillaria spp. collected in the Czech Republic. A total of five single-stranded RNA viruses were detected in Armillaria ostoyae and A. cepistipes, including the first virus of the family Tymoviridae found infecting a member the genus Armillaria and four viruses belonging to the recently described virus group "ambiviruses" with circular ambisense genome organization. Both hammerhead (HHRz) and hairpin (HpRz) ribozymes were detected in all the ambiviricot sequences. Armillaria viruses were compared by phylogenetic analysis and confirmed their specific host by direct RT-PCR, which showed the occurrence of interspecies transmission.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

The term Conjugated Linoleic Acid (CLA) refers generically to a class of positional and geometric conjugated dienoic isomers of linoleic acid. Among the isomers of linoleic acid cis9, trans11-CLA (c9, t11-CLA) and trans10, cis12-CLA (t10, c12-CLA) are found to be bio-logically active isomers, and they occur naturally in milk, dairy products and meat from ruminants. In addition, some vegetables and some sea-foods have also been reported to contain CLA. Although the CLA levels in these natural sources are insufficient to confer the essential health benefits, anti-carcinogenic or anti-cancer effects are of current interest. In the rumen, CLA is an intermediate of isomerization and the biohydrogenation process of linoleic acid to stearic acid conducted by ruminal microorganisms. In addition to rumen bacteria, some other bacteria, such as Propionibacterium, Bifidobacterium and some lactic acid bacteria (LAB) are also capable of producing CLA. In this regard, Lactiplantibacillus plantarum (formerly Lactobacillus plantarum) has demon-strated the ability to produce CLA isomers from linoleic acid by multiple enzymatic activi-ties, including hydration, dehydration, and isomerization. L. plantarum is one of the most versatile species of LAB and the bacterium is widely used in the food industry as a micro-bial food culture. The studies reviewed in this article reveal how, in the production of some fermented foods, the use of appropriate strains of L. plantarum, as a starter or additional culture, can be considered a critical factor in the design of new CLA-enriched functional foods.

Energy and information are fundamental concepts that play crucial roles in the foundations of science, each contributing to different aspects of our understanding of the natural world. Here we encounter that Fisher' measure is able to link them. We also investigate some interesting relations between Fisher's information, Poisson's distribution, and thermal quantifiers in a grand canonical ensemble. These connections permit one to visualize interesting novel artifacts in statistical mechanics. We clearly see them emerge in discussing the ideal gas. For example, we encounter that the Poisson distribution is intrinsically involved in the physics of the ideal gas, and we are able to give a Fisher-estimation of the difference in informational content between the grand canonical and canonical ensembles.

Functional articular cartilage regeneration remains an unmet medical challenge, increasing the interest for innovative biomaterial-based tissue engineering (TE) strategies. Hydrogels, 3D macromolecular networks with hydrophilic groups, present articular cartilage-like features such as high water content and load-bearing capacity. In this study, 3D porous polyethylene glycol diacrylate (PEGDA) hydrogels were fabricated combining the gas foaming technique and an UV-based crosslinking strategy. The 3D porous PEGDA hydrogels were characterized in terms of their physical, structural and mechanical properties. Our results showed that the size of the hydrogels pores can be modulated by varying the initiator concentration. In vitro cytotoxicity tests showed that 3D porous PEGDA hydrogels presented high biocompatibility both with human chondrocytes and osteoblast-like cells. Importantly, the 3D porous PEGDA hydrogels supported the viability and chondrogenic differentiation of human bone marrow-derived mesenchymal stem/stromal cells (hBM-MSCs)-based spheroids as demonstrated by the positive staining of typical cartilage extracellular matrix (ECM) (glycosaminoglycans (GAGs)) and upregulation of chondrogenesis marker genes. Overall, the produced 3D porous PEGDA hydrogels presented cartilage-like mechanical properties and supported MSC-spheroid chondrogenesis, highlighting their potential as suitable scaffolds for cartilage TE or disease modelling strategies.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavourable drugs properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use as inhalable formulations. Particulate-solid HA-VAN25 complex by spray drying from an aqueous dispersion was obtained. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern by X-ray was observed. The powder density, geometric size and morphology showed a suitable aerosolization and aerodynamic performance of the powder, indicating the capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 hours. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus, showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

In this article we investigate the determinants of marketing or organizational innovators in Europe for 36 countries in the period 2010-2019. We have used data from the European Innovation Scoreboard-EIS of the European Commission. We perform different econometric models i.e. Dynamic Panel, Pooled OLS, Panel Data with Fixed Effects, Panel Data with Random Effects, WLS. Results show that the level of marketing or organizational innovators in positively associated, among others variables to “Innovation Index”, “Innovators” and “Knowledge Intensive Service Exports”, while is negatively associated with “Sales Impacts”, “Foreign Controlled Enterprises Share of Value Added” and “Government procurement of advanced technology products”.

The following article analyzes Italian companies with more than 10 employees that use online sales tools. The data used were acquired from the ISTAT-BES database. The article first presents a static analysis of the data aimed at framing the phenomenon in the context of Italian regional disparities. Subsequently, a clustering with k-Means algorithm is proposed by comparing the Silhouette coefficient and the Elbow method. The investigation of the innovative and technological determinants of the observed variable is carried out through the application of a panel econometric model. Finally, different machine learning algorithms for prediction are compared. The results are critically discussed with economic policy suggestions.

In the following article I analyze the determinants of regular internet users in the Italian regions. The data is analyzed both in terms of static analysis and also through the application of the k-Means algorithm optimized with the Elbow method. Subsequently, an econometric model is presented for estimating regular internet users in the Italian regions based on variables that reflect the state of technological innovation and digital culture. The results are analyzed and discussed in light of the implications that digitalisation has for triggering economic growth.

In the following article I take into consideration the role of knowledge workers in the Italian regions. The analysed data refers to the ISTAT-BES database. The metric analysis consists of an in-depth analysis of the trends of the regions and macro-regions, followed by clustering with the k-Means algorithm, the application of machine learning algorithms for prediction, and the presentation of an econometric model with panel methods date. The results are also critically discussed in light of the North-South divide and the economic policy implications.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

Turner syndrome (TS) is caused by a complete or partial absence of an X or Y chromosome, including chromosomal mosaicism, affecting 1 in 2,500 female live births. Sister chromatid exchange (SCE) is used as a sensitive indicator of spontaneous chromosome instability. Cells from mosaic patients constitute useful material for SCE evaluations as they grow under the influence of the same genetic background and endogenous and exogenous factors. We evaluated proliferation dynamics and SCE frequencies of 45,X and 46,XN cells of 17 mosaic TS patients. In two participants, 45,X cells exhibited a proliferative disadvantage in relation to 46,XN cells after 72h of cultivation. The analysis of mean PI showed significant differences between 45,X and 46,XN lineages; however there were no intraindividual differences. On the other hand, mean SCE frequencies showed no differences between the two lineages, but there were intraindividual differences in 5 patients. The absence of mean SCE frequency differences between 45,X and 46,XN lineages may indicate that both were equally unstable, as more than 70% of the 46,XN lineages had an anomalous karyotype. However, 46,XN had a higher mean PI, suggesting that the amount of cells with a karyotype distinct from 45,X may increase with time in mosaic TS women.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

In voice analysis, the electroglottographic (EGG) signal has long been recognized as a useful complement to the acoustic signal, if only when the vocal folds are actually contacting, such that this signal has an appreciable amplitude. However, phonation can occur also without vocal fold contacting, as in breathy voice, in which case the EGG amplitude is low, but not zero. It is of great interest to identify the transition from non-contacting to contacting, because this will substantially change the nature of the vocal fold oscillations; yet that transition is not in itself audible. The magnitude of the normalized peak derivative of the EGG signal is a convenient indicator of contacting, but no current EGG hardware has a sufficient signal-to-noise ratio of the derivative. The textbook techniques of spectral thresholding and static notch filtering are straightforward to implement, can run in real time, and can mitigate several noise problems in EGG hardware.

Recently quantum cosmology in tomographic representation was considered. as an important tool to analyze the quantum states of the early universe in relation with the subsequent classical evolution. Given a wave function the correspondent tomogram is defined proportional to the square modulus of its fractional Fourier transform. The classical limit obtained by taking the limit ℏ→0 can be compared with the classical tomogram obtained from the classical hamiltonian formalism. In this paper we show that a set of tomograms can be derived as exact solutions of a third order equation when a de Sitter quantum universe is considered. We finally discuss the limits of this approach to quantum cosmology because the extension to equations with arbitrary potentials can become extremely complicated for potentials given by algebraic polynomials of degree greater than two and therefore also for potentials expressible by arbitrary functions.

Despite advances in algorithms and computational platforms, de-novo genome assembly remains a challenging process. Due to the constant innovation in sequencing technologies (Sanger, SOLiD, Illumina, 454, PacBio and Oxford Nanopore), genome assembly has evolved to respond to the changes in input data type. This paper includes a broad and comparative review of the most recent short-read, long-read and hybrid assembly techniques. In this review, we provide (1) an algorithmic description of the important processes in the workflow that introduces fundamental concepts and improvements; (2) a review of existing software that explains possible options for genome assembly; and (3) a comparison of the accuracy and the performance of existing methods executed on the same computer using the same processing capabilities and using the same set of real and synthetic datasets. Such evaluation allows a fair and precise comparison of accuracy in all aspects. As a result, this paper identifies both the strengths and weaknesses of each method. This comparative review is unique in providing a detailed comparison of a broad spectrum of cutting-edge algorithms and methods.

Ideas about Artificial Intelligence appeared about half a century ago, but only now is it becoming an essential element of everyday life. The data provided is getting bigger and bigger and, in this case, we need artificial intelligence that helps us with superhuman powers. The interaction with medicine is getting closer and closer, medicine being a field that continues to be perfected. Machine learning, deep learning, neural networks, computer vision are some of the mechanisms that are already applied in medicine, becoming a trend in healthcare worldwide. Artificial intelligence will be the thing that will change contemporary medicine. Developed countries such as Japan, France, Germany have already implemented artificial intelligence in their medical systems. The help is in medical diagnosis, patient monitoring, personalized therapy, and workflow optimization. Artificial intelligence will help surgeons to perfect their skills, to standardize techniques, to choose the best surgical technique. The goal is to predict complications, reduce diagnostic time, diagnose complex pathologies, guide the surgeon intraoperatively and reduce medical errors. We are at the beginning but the potential is enormous.

A single water pollution by dyes is a huge environmental problem; there is a necessity to produce new decolorization methods that are effective, cost-attractive, and suitable in industrial use. Magnetic chitosan polymers offer the advantage of easy separation from the dye solution. In this work, a Chitosan-Fe polymer was synthesized, characterized, and tested for removal of the azo dye Direct Red 83:1 from water. The polymer was characterized in terms of surface morphology (SEM), elemental analysis (EA), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), infrared spectrophotometry (IR), X-ray powder diffraction (XRD) and density functional theory (DFT). The reported results hint that 1 g and pH 7.0 were the best conditions to carry out both kinetic and isotherm models. To understand the adsorption behavior of Direct Red 83:1 onto the polymers, adsorption rate and maximum adsorption capacity were calculated using kinetic tests and isotherm curves respectively. The kinetic data and mechanism of the adsorption process were analyzed by three models and the equilibrium data by three adsorption isotherms. The results indicated that the adsorption process follows a pseudo-second-order kinetics (R2= 0.999) and fits the Temkin isotherm (R2= 0.946), indicating that the adsorption occurred on heterogeneous surfaces. The newly synthesized Chitosan-Fe polymer exhibited good adsorption properties and easy separation of cleaned water.

In this article we analyze the determinants and the export trend of European countries of medium and high technology products. The data were analyzed using various econometric models, namely WLS, Pooled OLS, Dynamic Panel, Panel Data with Fixed Effects, Panel Data with Random Effects. The results show that exports of medium and high-tech products are positively associated, among other variables, with the value of “Average Annual GDP Growth”, “Total Entrepreneurial Activity” and “Sales Impacts”, and negatively associated with, among other variables, “Human Resources”, “Government and Procurement of Advanced Technology Products” and “Buyer Sophistication”. A cluster analysis was realized with the k-Means algorithm optimized with the Silhouette coefficient. The result showed the presence of only two clusters. Since this result was considered poorly representative of the industrial complexity of the European Union countries, a further analysis was carried out with the Elbow method. The result showed the presence of 6 clusters with the dominance of Germany and the economies connected to the German economy. In addition, a network analysis was carried out using the distance to Manhattan. Four complex network structures and two simplified network structures were detected. A comparison was then made between 10 machine learning algorithms for predicting the value of exports of medium and high-tech products. The result shows that the best performing algorithm is the SGD. An analysis with Augmented Data-AD was implemented with a comparison between 10 machine learning algorithms for prediction and the result shows that the Linear Regression algorithm is the best predictor. The prediction with the Augmented Data-AD allows to reduce the MAE by about 0.0022131 compared to the prediction with the Original Data-OD.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

In this article we investigate the determinants of the European “Most Cited Publications”. We use data from the European Innovation Scoreboard-EIS of the European Commission for the period 2010-2019. Data are analyzed with Panel Data with Fixed Effects, Panel Data with Random Effects, WLS, and Pooled OLS. Results show that the level of “Most Cited Publications” is positively associated, among others, to “Innovation Index” and “Enterprise Birth” and negatively associated, among others, to “Government Procurement of Advanced Technology Products” and “Human Resources”. Furthermore, we perform a cluster analysis with the k-Means algorithm either with the Silhouette Coefficient and the Elbow Method. We find that the Elbow Method shows better results than the Silhouette Coefficient with a number of clusters equal to 3. In adjunct we perform a network analysis with the Manhattan distance, and we find the presence of 4 complex and 2 simplified network structures. Finally, we present a confrontation among 10 machine learning algorithms to predict the level of “Most Cited Publication” either with Original Data-OD either with Augmented Data-AD. Results show that the best machine learning algorithm to predict the level of “Most Cited Publication” with Original Data-OD is SGD, while Linear Regression is the best machine learning algorithm for the prediction of “Most Cited Publications” with Augmented Data-AD.

We consider an $N$ fermion system at low temperature $T$ in which we encounter special particle number values $N_m$ exhibiting special traits. These values arise in focusing attention upon the degree of mixture (DM) of the pertinent quantum states. Given the coupling constant of the Hamiltonian, the DMs stay constant for all $N$-values, but experience sudden jumps at the $N_m$. For a quantum state described by the matrix $\rho$, its purity is expressed by $Tr \rho^2$ and then the degree of mixture is given by $1 - Tr \rho^2$, a quantity that coincides with the entropy $S_q$ for $q=2$. Thus, Tsallis entropy of index two faithfully represents the degree of mixing of a state, that is, it measures the extent to which the state departs from maximal purity . Macroscopic manifestations of the degree of mixing can be observed through various physical quantities. Our present study is closely related to properties of many-fermion systemsn that are usually manipulated at zero temperature. Here we wish to study the subject at finite temperature. Gibbs' ensemble is appealed to. Some interesting insights are thereby gained.

Cervical cancer is a public health issue with high disease burden and mortality in Brazil. The objectives of the present study were analyzing age, period, and cohort effects on cervical cancer mortality in women 20 years old or older from 1980 to 2019 in the North, South, and Southeast Regions of Brazil; and evaluating whether the implementation of a national screening program and the expansion of access to public health services caused impacts over the examined period and reduced the risk of death over the past years and among younger cohorts. The effects were estimated by applying Poisson regression models with estimable functions. The highest mortality rate by 100,000 women was found in Amazonas (24.13), and the lowest in São Paulo (10.56). A positive gradient was obtained for death rates as women’s age increased. The states in the most developed regions (South and Southeast) showed a reduction in the risk of death in the period that followed the implementation of the screening program and in cohort from the 1960s onwards. The North Region showed a decreased risk of death only in Amapá (2000–2004) and Tocantins (1995–2004; 2010–2019). The findings indicated that health inequities remain in Brazil and suggested that the health system has limitations regarding decreasing mortality associated with this type of cancer in regions with lower socioeconomic development.

Solid state sensors having timing capabilities are becoming an absolute need in particle tracking techniques of future experiments at colliders. In this sense, silicon sensors having 3D structure are becoming an interesting solution, due to their intrinsic speed and radiation resistance. A characteristics of such devices is the strict dependence of their performance on their geometric structure, which can be widely optimised by design, thus requiring suitable tools for an accurate modeling of their behaviour. This paper illustrates the development, performance and use of the TCoDe simulator, specifically dedicated to the fast simulation of carrier transportation phenomena in solid state sensors. Some examples of its effectiveness in the design and analysis of 3D sensors is also given.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows to estimate direct, diffuse and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterisation techniques and allows the generation of high quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data and its resolution if two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

The new IoT/IoE (internet of things/everythings) paradigm and architecture permits to rethink about the way the Smart City infrastructures are designed and managed, on the other hand a number of problems have to be solved. In terms of mobility the cities that embrace the sensoring era can take advantage of this disruptive technology to improve the quality of life of their citizen, also thanks the rationalization in the use of their resources. In Sii-Mobility, a national smart city project on mobility and transportation, a flexible platform has been designed and here, in this paper, is presented. It permits to setup heterogeneous and complex scenarios that integrate sensors/actuators as IoT/IoE in an overall scenario of Big Data, Machine Learning and Data Analytics. A detailed and complex case-study has been presented to validate the solution in the context of a system that dynamically reverse the traveling direction of a road segment, with all the safety conditions in place. This case study composes several building blocks of the IoT platform, which demonstrate that a flexible and dynamic set-up is possible, supporting off-grid, security, safety, cloud and mixed solutions.

The experiences gathered during the past 30 years support the operational use of irrigation scheduling based on frequent multi-spectral image data. Currently, the operational use of dense time series of multispectral imagery at high spatial resolution makes monitoring of crop biophysical parameters feasible, capturing crop water use across the growing season, with suitable temporal and spatial resolutions. These achievements, and the availability of accurate forecasting of meteorological data, allow for precise predictions of crop water requirements with unprecedented spatial resolution. This information is greatly appreciated by the end users, i.e. professional farmers or decision-makers, and can be provided in an easy-to-use manner and in near-real-time by using the improvements achieved in web-GIS methodologies. This paper reviews the most operational and explored methods based on optical remote sensing for the assessment of crop water requirements, identifying strengths and weaknesses and proposing alternatives to advance towards full operational application of this methodology. In addition, we provide a general overview of the tools which facilitates co-creation and collaboration with stakeholders, paying special attention to these approaches based on web-GIS tools.

Artisanal and small-scale gold mining (ASGM) has been an important source of income for communities in the Madre de Dios River Basin in Peru for hundreds of years. However, in recent decades, the scale of ASGM activities in the region has increased dramatically, and exposures to a variety of occupational and environmental hazards related to ASGM, including mercury, are becoming more widespread. The aims of our study were to: (1) examine patterns in the total hair mercury level of human participants in several communities in the region and compare these results to the 2.2 µg/g total hair mercury level equivalent to the World Health Organization (WHO) Expert Committee of Food Additives (JECFA)’s Provisional Tolerable Weekly Intake (PTWI); and (2), to measure the mercury levels of paco (Piaractus brachypomus) fish raised in local aquaculture ponds, in order to compare these levels to the EPA Fish Tissue Residue Criterion of 0.3 µg Hg/g fish (wet weight). We collected hair samples from 80 participants in four communities (one control and three where ASGM activities occurred) in the region, and collected 111 samples from fish raised in 24 local aquaculture farms. We then analyzed the samples for total mercury. Total mercury levels in hair were statistically significantly higher in the mining communities than in the control community, and increased with increasing distance away from the Madre de Dios headwaters (as the crow flies), did not differ by sex, and frequently exceeded the reference level. Regression analyses indicated that higher hair mercury levels were associated with residence in ASGM communities. The analysis of paco fish samples found no samples that exceeded the EPA tissue residue criterion. Collectively, these results align with other recent studies showing that ASGM activities are associated with elevated human mercury exposure. The fish farmed through the relatively new process of aquaculture in ASGM areas appeared to have little potential to contribute to human mercury exposure. More research is needed on human health risks associated with ASGM to discern occupational, residential, and nutritional exposure, especially through tracking temporal changes in mercury levels as fish ponds age, and assessing levels in different farmed fish species. Additionally, research is needed to definitively determine that elevated mercury levels in humans and fish result from the elemental mercury from mining, rather than from a different source, such as the mercury released from soil erosion during deforestation events from mining or other activities.

In this article we investigate the role of “Renewable Energy Consumption” in the context of Circular Economy. We use data from the World Bank for 193 countries in the period 2011-2020. We perform several econometric techniques i.e., Panel Data with Fixed Effects, Panel Data with Random Effects, Pooled OLS, WLS. Our results show that “Renewable Energy Consumption” is positively associated among others to “Cooling Degree Days” and “Adjusted savings: net forest depletion” and negatively associated among others to “GHG net emissions/removals by LUCF” and “Mean Drought Index”. Furthermore, we perform a cluster analysis with the application of the k-Means algorithm optimized with the Silhouette Coefficient and we find the presence of two clusters. Finally, we compare eight different machine learning algorithms to predict the value of Renewable Energy Consumption. Our results show that the Polynomial Regression is the best algorithm in the sense of prediction and that on average the renewable energy consumption is expected to growth of 2.61%.

The use of privileged scaffolds as starting point for the construction of libraries of bioactive compounds is a widely used strategy in drug discovery and development. Scaffold decoration, morphing and hopping are additional techniques that allow to modify the privileged framework chosen and better explore the chemical space around it. In this study, two series of highly functionalized pyrimidine and pyridine derivatives were synthesized by scaffold morphing approach of triazine compounds obtained previously as antiviral agents. Newly synthesized azines were evaluated against lymphoma, hepatocarcinoma, and colon epithelial carcinoma cells showing in five cases acceptable to good anticancer activity associated to low cytotoxicity on healthy fibroblasts. Finally, ADME in vitro studies were conducted on the best derivatives of the two series showing good passive permeability and resistance to metabolic degradation.

We study different aspects of an exactly solvable master equation (ME). Its simplicity allows one direct access to the details of its workings, highlighting significant features and peculiarities. The existence of phase transitions is unveiled.

In this article, we estimate the value of Government Expenditure on Education-GEE in the context of Environmental, Social and Governance-ESG dataset of the World Bank. We use data from 193 countries in the period 2011-2020. We use Panel Data with Fixed Effects, Panel Data with Random Effects, Pooled Ordinary Least Squares-OLS, and Weighted Least Squares-WLS. Our results show that the value of GEE is positively associated among others to “Case of Death, by communicable disease and maternal, prenatal and nutrition conditions”, and “Unemployment”, and negatively associated among others to “Hospital Beds” and “Government Effectiveness”. Furthermore, we apply the k-Means algorithm optimized with the Elbow Method and we find the presence of four clusters. Finally, we confront eight machine learning algorithms for the prediction of the future value of GEE. We found that the Polynomial Regression is the best predictive algorithm. The Polynomial Regression predicts an increase in GEE of 7.09% on average for the analysed countries.

We analyze the question of GDP Growth-GDPG rate in the context of Environmental, Social and Governance-ESG framework. We use World Bank data for 193 countries in the period 2011-2020 using different econometric techniques i.e., Panel Data with Fixed Effects, Panel Data with Random Effects, Pooled Ordinary Least Squares-OLS. We found that GDPG rate is positively associated, among others, to “Government Effectiveness” and “Prevalence of Undernourishment” and negatively associated among others to “Unemployment” and “Research and Development Expenditure”. Furthermore, we have applied the k-Means algorithm optimized with the Elbow method and we found the presence of four clusters in the sense of GDPG rate. Finally, we confront eight machine learning algorithms to predict the value of GDPG rate and we found that the Polynomial Regression is the best predictor. The Polynomial Regression predicts an increase of GDPG rate equal to 2.88% on average for the analysed countries.

We estimate the determinants of Emissions-COE in the context of Environmental, Social and Governance-ESG model at world level. We use data of the World Bank for 193 countries in the period 2011-2020. We found that the level of COE is positively associated, among others to “Methane Emissions”, “Research and Development Expenditures”, and negatively associated among others to “Renewable Energy Consumption” and “Mean Drought Index”. Furthermore, we have applied a cluster analysis with the k-Means algorithm optimized with the Elbow Method and we find the presence of four cluster. Finally, we apply eight machine-learning algorithms for the prediction of the future value of COE and we find that the Artificial Neural Network-ANN algorithm is the best predictor. The ANN predicts a reduction in the level of COE equal to 5.69% on average for the analysed countries.

In this article, we estimate the role of Political Stability and Absence of Violence and Terrorism-PS in the context of Environmental, Social and Governance-ESG data at world level. We analyse data from 193 countries in the period 2011-2020. We apply Panel Data with Fixed Effects, Panel Data with Random Effects and Pooled Ordinary Least Square-OLS. We found that PS is positively associated, among others, to Population Density and Government Effectiveness, and negatively associated, among others, to Research and Development Expenditure and Maximum 5-day Rainfall. Furthermore, we apply the k-Means algorithm optimized with the application of the Elbow Method and we find the presence of four clusters. Finally, we propose a confrontation among eight different machine-learning algorithms for the prediction of PS and we find that the Polynomial Regression shows the higher performance. The Polynomial Regression predicts an increase in the level of PS of 0.25% on average for the analysed countries.

The development of plant-based meat analogues has become a significant challenge for the food industry in recent years due to the increasing demand for sustainable and healthier proteins in the context of a global protein transition. Plant-based meat analogues imitate the visual, textural, and chemical properties of traditional meat products and are required to closely resemble meat to appeal to consumers. In addition, consumers demand natural, clean-label, and nutritional and healthy products. To address these challenges, the food industry must develop highly healthy, nutritious, and E-number-free meat analogue products. Understanding the functionality of each ingredient and its role in the food matrix is crucial to being a key player in the innovation of the meat analogues market. This review provides updated information on the primary ingredients utilized for the development of plant-based burger meat alternatives and their functionality. The key components of meat analogue burgers are outlined, including plant proteins, binding agents, fats and oils, flavorings, colorings, preservatives, fortificants, and clean-label considerations.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p &lt; 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p &lt; 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

Glioblastoma multiforme (GBM) is the most frequent and aggressive primary brain tumor. GBM is formed by a very heterogeneous astrocyte population, neurons, neovascularization and infiltrating myeloid cells (microglia and monocyte derived macrophages). The IQGAP1 scaffold protein interacts with components of the cytoskeleton, cell adhesion molecules, and several signaling molecules to regulate cell morphology and motility, cell cycle and other cellular functions. IQGAP1 overexpression and delocalization has been observed in several tumors, suggesting a role for this protein in cell proliferation, transformation and invasion. IQGAP1 has been identified as a marker of amplifying cancer cells in GBMs. To determine the involvement of IQGAP1 in the onco-biology of GBM, we performed immunohistochemical confocal microscopic analysis of the IQGAP1 protein in human GBM tissue samples using cell type-specific markers. IQGAP1 immunostaining and subcellular localization was heterogeneous; the protein was located in the plasma membrane and, at variable levels, in nucleus and/or cytosol. Moreover, IQGAP1 positive staining was found in podosome/invadopodia-like structures. IQGAP1⁺ staining was observed in neurons (Map2⁺ cells), in cancer stem cells (CSC; nestin⁺) and in several macrophages (CD31⁺ or Iba1⁺). Our results indicate that the IQGAP1 protein is involved in normal cell physiology as well as oncologic processes.

In this study, using information theory tools, we investigate the quantum degree of mixedness, particle number fluctuations, and temperature variations in the paradigmatic Lipkin model, focusing on the interplay between these factors in a system of many fermions. Our analysis reveals intriguing dependencies of quantum mixedness on the total fermion number, showcasing distinct behaviors at different temperatures. Notably, we find that the degree of quantum mixedness exhibits a strong dependence on the total fermion number, with varying trends observed across different temperature regimes. Remarkably, this dependence remains unaffected by the strength of the fermion-fermion interaction (if it does not vanish, of course), underscoring the robustness of the observed phenomena. Through comprehensive numerical simulations, we provide illustrative graphs that depict these dependencies, offering valuable insights into the fundamental characteristics of many-fermion systems. Our findings shed light on the intricate dynamics of quantum degree of mixedness and particle number fluctuations in fermionic systems, with potential implications for diverse fields ranging from condensed matter physics to quantum information science.

Background: Diabetes mellitus (DM) and periodontitis are two chronic diseases that are interconnected. The coexistence of these conditions leads to increased severity of periodontitis and challenges in controlling blood glucose levels in diabetic patients. Objectives: The aim of this study was to evaluate both the influence of periodontal disease and its treatment in patients with DM in terms of a reduction in glycosylated hemoglobin levels at 3 and 6 months after treatment. Methods: A sequential, nonprobabilistic, controlled, prospective and longitudinal case−control study was carried out at the University Dental Clinic of the Morales Meseguer Hospital in Murcia, Spain. Thirty diabetic patients were divided into two groups: patients with periodontitis (test group) and patients without periodontitis (control group). The periodontal and endocrine-metabolic variables were measured at baseline and at 3 and 6 months after periodontal treatment for both groups. Results: Statistically significant differences were found at 3 and 6 months after periodontal treatment with respect to HbA1c levels in the group of periodontal patients. However, these differences were not observed in the control group. Conclusion: The presence of periodontal disease increased HbA1c levels in patients with DM. Nonsurgical periodontal treatment significantly decreased the degree of periodontal inflammation and the HbA1c level at 3 and 6 months after treatment.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

Fungal infections caused by Candida spp. are responsible for high hospital morbidity and mortality rates. Therefore, there is a continuous search for new antifungal medicines, particularly ones with anti-Candida activity. This review analyzed articles published between 2002 and 2023 considering the anti-Candida activity of chemical compounds identified or isolated in plants of the Anacardiaceae family. In addition, the in-silico prediction of the isolated compounds described was performed. The analysis of 35 studies showed that extracts, essential oils, and compounds from the anti-Candida activity were frequently determined in vitro using the minimum inhibitory concentration (MIC). The most commonly tested species were Candida albicans, C. tropicalis, C. parapsilosis, C. glabrata, C. krusei, and C. guilliermondii, respectively. Essential oils were the most used form (37% of the studies). The isolated compounds with antifungal effects include cardanol, estragole, trans-anethole, β-caryophyllene, myrcene, catechin-3-o-rhamnoside, β-sitosterol-3-O-glucoside, 24Z-isomasticadienolic acid, oleanolic acid, and oleanolic aldehyde. The in-silico evaluation of those isolated compounds revealed the compounds' drug-likeness and possible antifungal activity. However, some of them showed high toxicity. In conclusion, compounds from the Anacardiaceae family show promise for developing new therapeutic antifungal drugs, especially in combination with conventional antifungals.

We explore an idea put forward many years ago by Zeldovich and Novikov concerning the existence of compact objects endowed with arbitrarily small mass. The energy-density of such objects, which we call “Ghost stars”, is negative in some regions of the fluid distribution, producing a vanishing total mass. Thus, the interior is matched on the boundary surface to Minkowski space-time. Some exact analytical solutions are exhibited and their properties are analyzed. Observational data that could confirm or dismiss the existence of this kind of stellar object, is commented.

A semi–numerical approach proposed many years ago for describing gravitational collapse in the post–quasi–static approximation , , , , is modified in order to avoid the numerical integration of the basic differential equations the approach is based upon. For doing that we have to impose some restrictions on the fluid distribution. More specifically, we shall assume the vanishing complexity factor condition, which allows for analytical integration of the pertinent differential equations and leads to physically interesting models. Instead, we show that neither the homologous nor the quasi–homologous evolution are acceptable since they lead to geodesic fluids, which are unsuitable for being described in the post–quasi–static approximation. Also, we prove that, within this approximation, adiabatic evolution also leads to geodesic fluids and therefore we shall consider exclusively dissipative systems. Besides the vanishing complexity factor condition, additional information is required for a full description of models. We shall propose different strategies for obtaining such an information, which are based on observables quantities (e.g. luminosity and redshift), and/or heuristic mathematical ansatz. To illustrate the method, we present two models. One model is inspired in the well known Schwarzschild interior solution, and another one is inspired in Tolman VI solution.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

The entropic gravity conception proposes that what has been traditionally interpreted as unobserved dark matter might be merely the product of quantum effects. These effects would produce a novel sort of positive energy that translates into dark matter via $E=mc^2$. In the case of axions, this perspective as been shown to yield quite sensible, encouraging results [DOI:10.13140/RG.2.2.17894.88641] . There, a simple Schrodinger mechanism was utilized, in which his celebrated equation is solved with a potential function based on the microscopic Verlinde's entropic force advanced in [Physica A {\bf 511} (2018) 139]. In this effort we revisit such technique with regards to fermions' behavior (specifically, baryons).

We have developed a family of N-alkyl-nitrobenzamides that exhibit promising antitubercular ac-tivities. These compounds are a simplification of the structure of known inhibitors of DprE1, an essential Mtb enzyme and an emergent anti-TB target. The compounds were obtained by a simple synthetic methodology and their antitubercular, cyto-toxicity and stability were studied. The most active compounds were the 3,5-dinitro and the 3-nitro-5-trifluoromethyl derivatives. Lipophilicity was shown to be a main parameter modulating activity within each family. The most active compound presented MIC of 16 ng/mL and had in-termediate lipophilicities. The activity was also studied in a macrophage model of infection. In this model the compounds with chain lengths of 6 and 12 carbon atoms presented the best results, ex-hibiting activity profiles comparable to isoniazid. Docking studies performed suggested that the fit of our highly active compounds to the DprE1 binding pocket was very similar to the literature compounds. Furthermore, the metrics used in the analysis were able to distinguish between the families of the highly and least active compounds. Assessment of susceptibility over multiple species and computational together with the structure of the compounds are complementary information that supports DprE1 as a likely target of action for this type of compounds.

There are several well-described molecular mechanisms that influence cell growth and are relat-ed to the development of cancer. Chemokines constitute a fundamental element which are not only involved in local growth but also affect angiogenesis, tumor spread and metastatic disease. Among them, the C-X-C motif chemokine ligand 12 (CXCL12) and its specific receptor the chemo-kine C-X-C motif receptor 4 (CXCR4) have been widely studied. The overexpression in cell mem-branes of CXCR4 has been shown to be associated with the development of different kinds of his-tological malignancies, such as adenocarcinomas, epidermoid carcinomas, mesenchymal tumors or neuroendocrine neoplasms (NENs). The molecular synapsis between CXCL12 and CXCR4 leads to the interaction of G proteins and activation of different intracellular signaling pathways in both gastroenteropancreatic (GEP) and bronchopulmonary (BP) NENs conferring greater ca-pacity for locoregional aggressiveness, epithelial-mesenchymal transition (EMT) and the ap-pearance of metastases. Therefore, it has been hypothesized how to design tools that target this receptor. The aim of this review is to focus on current knowledge of the relationship between CXCR4 and NENs, with a special emphasis on diagnostic and therapeutic molecular targets.

The objective of this study was to determine how application with dolomitic limestone and grazing type (continuous or deferred) affect sheep grazing location and feed preference when the pasture growth rate is maximum. A 4ha field was divided into 4 plots: P1 and P2- without application of dolomitic limestone, continuous (CG) and deferred grazing (DG), respectively; P3 and P4- with application of dolomitic limestone, DG (1AUE), and CG (2.4 AUE), respectively. In DG, animals were placed and removed from the plots depending on the height of the pasture. In each plot, 12 georeferenced sampling points were identified. Throughout the pasture's vegetative cycle (autumn, winter, spring, and early summer) several measurements of pasture height and cut were carried out. From the beginning of March to the beginning of June, animal behavior was observed, by trained observers, through binoculars on six dates. Animals' activity grazing and location was recorded. The results show that: (i) the application of dolomitic limestone combined with CG provided higher values of pasture height; (ii) there were no significant differences in pasture quality between treatments; (iii) Deferred grazing led to 50% more sheep grazing days than continuous grazing; (iv) there were no significant differences in soil compaction between CG and DG; (v) the type of grazing and the treatment with dolomitic limestone did not seem to change the grazing pattern between treatments. This work contributes to understanding the relationships between different types of grazing in dryland pastures, with and without application of dolomitic limestone, and preferred grazing locations for sheep. This work could help agricultural managers make more informed decisions with the aim of promoting the sustainable intensification of livestock production in the Montado ecosystem.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.