To reduce environmental impacts from sodium silicate synthesis it was suggested the use of sugarcane bagasse ash (SCBA) as a source of silicon dioxide and sodium carbonate using the ceramic method. Although the production of sodium silicate is carried out on a large scale, it should be noted that its process requires temperatures above 1000 °C or the use of highly corrosive agents such as sodium hydroxide and chlorine gas used to neutralize the remaining sodium hydroxide. In the present work, the synthesis temperatures were reduced to 800 °C with a reaction time of 3 hours by pressing equimolar mixtures of previously purified SCBA and sodium carbonate, then heat treatment was carried out under the indicated conditions. The resulting materials were analyzed by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). Among the crystalline phases, calcium disodium silicate was identified, in addition to sodium silicate, so it was inferred that the other components of the ash can interfere with the synthesis of silicate. Therefore, to obtain the highest composition of sodium silicate, a leaching treatment of the SCBA is required.

The screen-printed carbon nanofibers electrodes (SPCNFE) represent an alternative with great acceptance due to their results, as well as their low impact for the environment. In order to improve their performance, in the present work they were modified with silver nanoparticles (Ag-NPs) and electrochemically characterized by using anodic stripping voltammetry. From the Ag-NPs synthesis, silver seeds (Ag-NS) and silver nanoprisms (Ag-NPr) were obtained. The Ag-NPs formation was confirmed by micrographs where Ag-NPs with diameters of 12.20±0.04 nm for Ag-NS, and 20.40±0.09 nm for Ag-NPr were observed. The electrodes were modified by using three different deposition methods: drop-casting, spin-coating and in-situ approaches. It was observed that the last methodology showed a low amount of Ag-NS deposited on the electrode surface and a deep alteration of this surface. Those facts suggested that the in situ synthesis methodology were not appropriate for the determination of heavy metals and it was discarded. The incorporation of the nanoparticles by spin-coating and drop-casting strategies showed different spatial distribution on the electrode surface as proved by scanning electron microscopy. The electrodes modified by these strategies, were evaluated for the cadmium(II) and lead(II) detection using differential pulse anodic stripping voltammetry, obtaining detection limit values of 2.1 and 2.8 µg L^-1, respectively. The overall results showed that the incorporation route does not change directly the electrocatalytic effect of the nanoparticles, but the shape of these nanoparticles (spherical for seeds and triangular for prisms) has a preferential electrocatalytical enhancement over Cd(II) or Pb(II).

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

In many of the current software applications, numerous vulnerabilities may be present.1 Attackers attempt to exploit existing vulnerabilities that lead to security breaches, unauthorized entry,2 data theft, or incapacitation of a computer system. Rather than addressing software or hardware3 vulnerabilities at a later stage, it is better to address them immediately. DevSecOps, when utilized4 in application development, tackles these vulnerabilities at an early stage. AIBughunter is a tool5 that addresses this problem in software and was developed by the ASWM research group to predict,6 classify, and repair software vulnerabilities. AIBughunter integrates LineVul to find vulnerable7 code lines and returns information about the type of vulnerability and its severity to developers.8 It also includes a tool, VulRepair, which detects and repairs vulnerabilities. VulRepair currently9 predicts patches for vulnerable functions at 44%. In order to become truly effective, this number 10 needs to be increased. This study examines VulRepair to see whether the 44% Perfect Prediction 11 can be increased. VulRepair is a T5 based model that uses Natural Language and Programming 12 Languages for pre-training along with Byte Pair Encoding. It outperforms other existing models, 13 such as VRepair and CodeBERT. However, the hyperparameters may not be optimized due to the 14 development of new optimizers. We review a Deep Neural Network (DNN) optimizer developed by 15 Google in 2023. This optimizer called Evolved Sign Momentum (LION) is available in PyTorch. We 16 applied this optimizer to VulRepair and tested its influence on hyperparameters. After adjusting the 17 hyperparameters, we obtained a 56% Perfect Prediction, which exceeds the value of the VulRepair 18 report of 44%. This means that VulRepair can repair more vulnerabilities and avoid more attacks. As 19 far as we know, our approach of utilizing an alternative to AdamW, the standard optimizer, has not 20 been previously applied to enhance VulRepair and similar models. 21

This paper provides estimates of the elasticity of substitution between operational and managerial jobs in the US economy covering a period of almost five decades, derived from an aggregate CES production function. Estimating the long-term relationship between (the log of) the aggregate employment/self-employment ratio and (the log of) the returns from paid-employment relative to self-employment and testing for structural breaks, we report different estimates of the elasticity of substitution in each of the two regimes identified. Our results help to understand and interpret one of the most intriguing aspects in the evolution of self-employment rates in developed countries: the reversal of the trend in self-employment rates. Our estimates show that a higher level of development is associated with a greater number of entrepreneurs and smaller firms. Some rationales for understanding the growth of the elasticity between paid-employment and self-employment, including the recent trends in the digital economy—are also suggested.

The absorption of medium-chain fatty acids (MCFA) depends on the solubility of these components in the gastric fluid. Parameters such as the total MCFA concentration, carboxyl ionization level, and carbon chain length affect the solubility of these molecules. Moreover, the enzymatic lipolysis of solubilized triacylglycerol (TAG) molecules may depend on the carbon chain length of the fatty acids (FAs) components and their positions on the glycerol backbone. This present study aimed at investigating the effect of electrolyte usually formed during the gastric digestion phase on the solubility of MCFA, and evaluating the influence of the FA carbon chain length on the lipolysis rate during the in vitro digestion simulation. The results obtained here showed that the increasing of electrolyte concentrations tend to decrease the mutual solubility of systems composed by the caproic and caprylic fatty acids + sodium chloride, sodium bicarbonate, and potassium chloride solutions. We also observed that a conventional version of the thermodynamic UNIQUAC model was able to correlate the liquid-liquid phase behavior of the electrolyte solutions. Regarding the in vitro digestion simulation, the experimental data indicated that the action of the pancreatic enzyme occurred preferentially in TAG molecules comprised of short and medium-chain fatty acids.

The purpose of this paper is to analyze how Green Business Models (BMs) established by small and medium enterprises (SMEs) can incorporate product and process decarbonization in their components (value proposition, creation and capture) and to what extent this incorporation is affected by SME size. We use a database comprising 1,161 observations of SMEs, 466 in 2014 and 695 in 2016. The results show that SMEs’ value propositions give an intermediate valuation to both legally required and voluntary reduction of environmental impact, irrespective of SME size and the year analyzed. Regarding value creation, SMEs adopt practically no environmental practices, and there are significant differences according to size, with more difficulties than advantages stemming from small size. The study also shows that such environmental practices are not effective in reducing carbon. This diagnosis indicates that SMEs need help from the administration if they are to play a key role in the process of transformation toward a low-carbon economy. Legislative actions involving harsher environmental protection measures might help shape value propositions that place greater importance on reducing environmental impact, whereas training actions on available environmental techniques, promotion of research on how to adapt such techniques to SMEs and the development of specific practices for SMEs might enhance environmental value creation and capture in their BMs.

Patients with Multiple Myeloma have an increased susceptibility to severe infections due to several various factors, especially the high tumor burden. The use of the anti-CD38 monoclonal antibodies-based therapies has changed the frequency and epidemiology of infections. We report herein the safety profile of the pivotal clinical trials conducted with anti-CD38 mAbs (daratumumab and isatuximab) and anti-SLAMF7 mAbs (elotuzumab) that led to the approval of regimens employed today in NDMM and RRMM patients.

Theoretical approaches to calculate pKa values for Brønsted acids is a challenging task that, most of the time, involves sophisticated and time-consuming methods. Therefore, heuristic approaches are efficient and appealing methodologies to approximate these values. Herein, by considering the electrostatic potential on acidic hydrogen atoms in a similar fashion that a σ–hole is defined, we calculated the maximum surface potential, V_S,max, and used it as a descriptor to correlate it with experimental acidity constants. These values were calculated using the CPCM implicit solvent model (water) with six different methods: five density functionals and the Møller–Plesset second order perturbation theory. Six different basis sets were combined with each method in order to benchmark a total of thirty-six levels of theory. Overall, 1080 calculations were performed and found to correlate with experimental data. The ωB97X-D/6-31+G(d,p) level of theory stands as the best one for consistently reproduce the reported pKa values.

We report on recent experimental results on β decay into self-conjugate (N=Z) nuclei with mass number 58≤A≤70. Super-allowed β decays from the Jπ=0+ ground state of a Z=N+2 parent nucleus are to the isobaric analogue state, through so-called Fermi transitions, and to Jπ=1+ states, by way of Gamow–Teller (GT) transitions. The operator of the latter decay is a generator of Wigner’s SU(4) algebra and as a consequence GT transitions obey selection rules associated with this symmetry. Since SU(4) is progressively broken with increasing A, mainly as a consequence of the spin–orbit interaction, this symmetry is not relevant for the nuclei considered here. We argue, however, that the pseudo-spin–orbit splitting can be small in nuclei with 58≤A≤70, in which case nuclear states exhibit an approximate pseudo-SU(4) symmetry. To test this conjecture, GT decay strength is calculated with use of a schematic Hamiltonian with pseudo-SU(4) symmetry. Some generic features of the GT β decay due to pseudo-SU(4) symmetry are pointed out. The experimentally observed GT strength indicates a restoration of pseudo-SU(4) symmetry for A=70.

The superconductivity of CaC6 as a function of pressure and of abundant Ca isotopes is revisited using DFT calculations on a 2c – double hexagonal superlattice. The introduction of superlattices is motivated by previous synchrotron absorption and Raman spectroscopy results on other superconductors that show evidence of superlattice vibrations at low (THz) frequencies. A 2c superlattice for CaC6 is illustrative of atomic orbital symmetry and periodicity, including bonding and antibonding s-orbital character implied by cosine modulated electronic bands. Inspection of the cosine band reveals that the cosine function has a small (meV) energy difference between bonding and antibonding regions relative to a midpoint non-bonding energy. Fermi surface nesting is apparent in an appropriately folded Fermi surface using a superlattice construct. Nesting relationships identify phonon vectors for conservation of energy and for phase coherency between coupled electrons at opposite sides of the Fermi surface. Detailed analysis of this Fermi surface nesting provides accurate estimates of the superconducting gaps for CaC6 with change in applied pressure. Recognition of superlattices within a rhombohedral or hexagonal representation provides consistent mechanistic insight on superconductivity and electron−phonon coupling in CaC6.

This review evaluates the trajectory and sustainability of the global and Mexican aquaculture industry. Globally, the sector is experiencing rapid growth, catalyzed by evolving consumption patterns and technological advancements. Notwithstanding the benefits, environmental concerns necessitate an urgent shift towards sustainable practices. The focus then narrows to Mexico's aquaculture, tracing its history from the late 19th century. With an emphasis on species diversification, the country's sector demonstrates resilience and potential, with an impressive yield of 249,613.71 tons in 2021 despite regional consolidation. However, persistent challenges such as technological limitations, funding shortages, and access to quality seeds hinder progress. Risks, including disease outbreaks, negative environmental impact, economic volatility, regulatory compliance, and climate change, further underscore the need for sustainable strategies. With government support and unique geographical and climatic advantages, Mexico shows promise for a significant % growth projection of 25% over the next five years. This review underscores the importance of embracing technological innovation, implementing sustainable practices, and enacting supportive legislation for the long-term success of the aquaculture sector worldwide, with a particular focus on Mexico.

(+)-epi-Epoformin (1), is a fungal cyclohexene epoxide isolated together with diplopimarane and sphaeropsidins A and C, a nor-ent-pimarane and two pimaranes, from the culture filtrates of Diplodia quercivora, a fungal pathogen for cork oak in Sardinia, Italy. Compound 1 possesses a plethora of biological activities including: antifungal, zootoxic and phytotoxic activity. The last activity and the peculiar structural feature of 1 suggested to carry out a structure activity relationship study, preparing eight key hemisynthetic derivatives and their phytotoxicity was assayed. The complete spectroscopic characterization and the activity in the etiolated wheat coleoptile bioassay of all the compounds is reported. Most of the compounds inhibited growth and some of them had comparable or higher activity than the natural product and the reference herbicide Logran. As regards the structure-activity relationship, the carbonyl proved to be essential for their activity of 1, as well as the conjugated double bond, while the epoxide could be altered with no significant loss.

In the present work we propose a dynamical mathematical model of the lung cells inflammation process in response to SARS-CoV-2 infection. In this scenario the main protease Nsp5 enhances the inflammatory process, increasing the levels of NF kB, IL-6, Cox2, and PGE2 with respect to a reference state without the virus. In presence of the virus the translation rates of NF kB and IkB arise to a high constant value, and when the translation rate of IL-6 also increases above the threshold value of 7 pg mL^-1 s^-1 the model predicts a persistent over stimulated immune state with high levels of the cytokine IL-6. Our model shows how such over stimulated immune state becomes autonomous of the signals from other immune cells such as macrophages and lymphocytes, and does not shut down by itself. We also show that in the context of the dynamical model presented here, Dexamethasone or Nimesulide have little effect on such inflammation state of the infected lung cell, and the only form to suppress it is with the inhibition of the activity of the viral protein Nsp5.To that end, our model suggest that drugs like Saquinavir may be useful. In this form, our model suggests that Nsp5 is effectively a central node underlying the severe acute lung inflammation during SARS-CoV-2 infection. The persistent production of IL-6 by lung cells can be one of the causes of the cytokine storm observed in critical patients with COVID19. Nsp5 seems to be the switch to start inflammation, the consequent overproduction of the ACE2 receptor, and an important underlying cause of the most severe cases of COVID19.

Climacteric fruits undergo a characteristic ripening process regulated by ethylene, a key plant hormone. Extending the shelf life of these fruits while preserving their postharvest quality poses a significant challenge for the food industry. This review provides a comprehensive overview of physiological and molecular strategies to delay ethylene-mediated ripening in climacteric fruits and their impact on shelf life, postharvest quality, sensory attributes, and volatile compounds. Additionally, it examines the role of ethylene in fruit ripening analysing various ethylene managing strategies including ethylene inhibitors, ethylene adsorbents and ethylene scavengers by catalytic oxidation The review concludes with future research directions including integrated strategies, environmental considerations and commercial applications for improving postharvest handling and fruit quality.

Fruits of chayote [Sechium edule (Jacq.) Swartz] are widely consumed in Mesoamerica, but little is known about the nutraceutical potential. This study aimed to determine the chemical compositions, antioxidant activities from the juice fruits from two commercial varieties of chayote cultivated in Mexico, as well as a proposal for the elaboration of chayote juices with stevia leaves and pineapple juice. The physicochemical properties of juice from virens levis (VL) and nigrum spinosum (NS) varieties were determined using standard methods. The juice of the two varieties differ significantly regarding the concentrations of total soluble solids, total sugars, but not vitamin C. The total concentration of phenolics in NS extracts was slightly higher than in VL (1005 and 856 mg 100 g⁻¹ dry-weight, respectively) but the total flavonoid contents were similar (27 and 26 mg 100 g⁻¹ dry-weight, respectively). Cucurbitacin D was predominant in both varieties. The radical scavenging capacities of VL and NS extracts varied slightly (IC50 = 0.45 to 0.65 mg mL⁻¹), while the antioxidant activities were similar (~80%). The NS variety is particularly promising regarding nutraceutical application. The chayote juice combined with stevia and pineapple maintain the original nutraceutical characteristics from the fruit, but enhanced the organoleptic characteristics like density and sugar/acidity balance.

This paper introduces the implementation of a genetic programming (GP)-based procedure to the automatic design and tuning of process controllers. The proposed approach makes a significant contribution to the field of artificial intelligence (AI) in control engineering. Unlike other controller design methods, the GP-based program handles the entire design in the time domain, including differential operations like derivatives and integrals, without the need for intermediate inverse Laplace transformation. This approach not only simplifies the design process but also ensures that all generated controllers are implementable in physical systems. Furthermore, GP’s functions set includes various mathematical operations beyond basic arithmetic operators, such as trigonometric, exponential, and logarithmic operators. The performance and validity of the resulting controllers generated by the proposed GP-based approach are evaluated by verifying whether the generator can replicate the structure and performance of those produced by traditional controller design methods and, in some cases, achieve even better results. As a result, the GP-based approach presents a promising solution for automating the controller design process and addressing control problems in various engineering applications.

Satellite derived bathymetry methods over coastal areas were born to deliver basic and useful information like bathymetry. However, the process is not straightforward, the main limitation being the need of field data. The Self-calibrated Spectral Supervised Shallow-water Modeler (4SM) method was tested to obtain coastal bathymetry without the use of any field data. Using LANDSAT-8 multispectral images from 2013 to 2016, a bathymetric time series was produced. Groundtruthed depths and an alternative method, Stumpf’s Band Ratio Algorithm, were used to verify the results. Retrieved (4SM) vs groundtruthed depths scored an average r2 (0.90), and a low error (RMSE = 1.47 m). Also 4SM showed, over the whole time series, the same average accuracy of the control method (40%). Advantages, limitations and operability under complex atmosphere and water column conditions, and high and low-albedo bottom processing capabilities of 4SM are discussed. In conclusion, the findings suggest that 4SM is equally accurate as the commonly used Stumpf’s method, the only difference being the independence of 4SM to previous field data, and the potential to deliver bottom spectral characteristics for further modelling. 4SM represents a significative advance in coastal remote sensing potential to obtain bathymetry and optical properties of the marine bottom.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Composites of Ag and TiO2 nanoparticles on cotton fabrics were synthetized in-situ by sono-chemical and hydrothermal methods achieving the successive formation of Ag-NPs and Ti-NPs directly on the fabric. The impregnated fabrics were characterized by ATR-FTIR spectroscopy, high resolution microscopy (HREM), scanning electron microscopy coupled with Ener-gy-dispersive X-ray spectroscopy (SEM-EDS), Raman, photoluminescence, UV-vis and DRS spectroscopies and by tension tests. Results showed the successful formation and impregnation of NPs on the cotton fabric, with a negligible leaching of NPs after several washing cycles. The photocatalytic activity of supported NPs was assessed by the degradation of methyl blue dye (MB) under solar and UV irradiation revealing improved photocatalytic activity of the Ag-TiO2/cotton composites due to a synergy of both Ag and TiO2 nanoparticles. This behavior is attributed to a diminished electron-hole recombination effect in the Ag-TiO2 cotton samples. The biocide activity of these composites on the growth inhibition of Staphylococcus aureus (Gram+) and Escherichia coli (Gram-) was confirmed, revealing interesting possibilities for the utilization of the functionalized cotton fabric as protective cloth for medical applications.

Commonly, professors, students and researchers from universities around the world use software distributed under a license agreement for computer simulation purposes, which requires a computer with considerable hardware capabilities. Consequently, this implies a high cost to conduct simulations that require implementing numerical methods in all areas of engineering, particularly in the field of robotics and nonlinear control. This paper presents the design and results analysis of a low-cost and open-source frugal computer simulation tool with applications to robotic nonlinear control, for instance, for numerical simulations of manipulator robot control based on dynamic models. Using a single board minicomputer with with reduced computing power, Raspberry Pi, together with free software, GNU-Octave, trajectory tracking control simulations in the joint space of a Selective Conformal Assembly Robot Arm (SCARA) are achieved by solving a system of nonlinear differential equations, represented in matrix form, which includes the control law and the system model. The results of the proposed alternative are compared by running the same simulation code on a laptop computer using MATLAB and GNU Octave, which show minimal deviations and reasonable time complexity. Moreover, considering the frugality curve calculated for this approach, in addition to the low acquisition cost of the simulation software tool, it would allow the creation of a simulation laboratory in some universities with budgetary constraints for educational and research purposes.

The electronic properties of calcium intercalated graphite (CaC6) as a function of pressure are revisited using density functional theory (DFT). The electronic band structures of CaC6, like many other layered superconducting materials, display cosine-shaped bands at or near the Fermi level (FL). Such bands encompass bonding/antibonding information with a strong connection to superconducting properties. Using an hexagonal cell representation for CaC6, construction of a double supercell in the c-direction effects six-folding in reciprocal space of the full cosine function, explicitly revealing the bonding/antibonding relationship divide at the cosine midpoint. Similarly, folding of the Fermi surface (FS) reveals physical phenomena relevant to electronic topological transitions (ETT) with application of pressure. For CaC6, the peak value for the superconducting transition temperature, Tc, occurs at about 7.5 GPa, near to the observed pressure of the calculated ETT. At this pressure, the radius of the nearly spherical Ca 4s-orbital FS coincides with three times the distance from the G centre point to the Brillouin zone (BZ) boundary of the 2c supercell (which is equal to half the identically defined distance for the primitive rhombohedral BZ). In addition, the ETT coincides with alignment of the non-bonding (inflection) point of the cosine band (the point at which the sign of the cosine amplitude modulation is reversed) with the FL. At other calculated pressure conditions, the Ca 4s-orbital FS undergoes topological changes that correspond and can be correlated to experimentally determined changes in Tc. The ETT is a key mechanism that circumscribes the known significant drop in Tc for CaC6 as a function of increasing pressure.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

Sechium compositum (Cucurbitaceae) is a wild species that is distributed in the Soconusco region, Chiapas, Mexico, and the border with Guatemala. This species has an intangible biochemical value resulting from the pharmacological relevance of its secondary metabolites. However, as a consequence of the lack of knowledge about its importance, it is being displaced from its habitat at an accelerated rate, incurring the risk of genetic loss. Therefore, an in vitro culture protocol with two experimental phases was evaluated to propagate, conserve, and regenerate this species. The first phases considered the multiplication of seedlings, adding seven concentrations (0.1, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2 mg mL-1) of 6-benzylaminopurine (BA) and thidiazuron (TDZ) and evaluating the number of buds, shoots, and seedling height. The best multiplication response was recorded with 0.1, 0.2, 0.4, and 1.0 mg L-1 of BA and 0.1 mg L-1 of TDZ, as well as the MS base culture medium. With 0.1 mg L-1 of BA, 52-mm height, 1.36 shoots, and 9.22 buds were obtained, surpassing the MS control (MS culture medium alone); likewise, twice more roots (80%) and a 14% reduction in the bud structure were packed in 50 repetitions. The second phase consisted of inducing callus formation from stem and leaf explants through the addition of 0.5, 1.0, and 2.0 mg L-1 of TDZ and 2,4-Dichlorophenoxyacetic acid (2,4-D) to the medium. The results demonstrated that the induction of callogenesis in S. compositum has a better start from the stem in a medium with 2.0 mg L-1 of 2,4-D, whose value was 4.89 —equivalent to 97.8% callus formation around the explant. The addition of 500 mg L-1 of polyvinylpyrrolidone (PVP) is also suggested to reduce oxidation. This protocol represents a significant advance in the conservation, multiplication, and callogenesis of S. compositum and contributes to its rescue and revaluation in the face of the danger of extinction.

Wrist shape varies greatly across primates and previous studies indicate that the numerous morphological differences among them are related to a complex mixture of phylogeny and function. However, little is known about whether the variation in these various anatomical differences is linked and to what extent the wrist bones vary independently. Here, we used 3D geometric morphometrics on a sample of extant hominids (Homo sapiens, Pan troglodytes, Gorilla gorilla, and Gorilla beringei), to find the model that best describes the covariation patterns among four of the eight carpals (i.e., capitate, lunate, scaphoid, and trapezium). For this purpose, 15 modular hypotheses were tested using the Covariation Coefficient. Results indicate that there is a covariation structure common to all hominids, which corresponds to stronger covariation within each carpal as compared to the covariation between carpals. However, the results also indicate that that there is a degree of codependence in the variation of some carpals, which is unique in humans, chimpanzees, and gorillas, respectively. In humans there is evidence of associated shape changes between the lunate and capitate, and between the scaphoid and trapezium. This covariation between lunate and capitate is also apparent in gorillas, while chimpanzees display the greatest disassociation among carpals, showing low covariation values in all pairwise comparisons. Our analyses indicate that carpals have an important level of variational independence which might suggest a high degree of independent evolvability in the wrists of hominids, and that although weak, the structure of associated changes of these four carpals varies across genera. To our knowledge this is the first report on the patterns of modularity between these four wrist bones in the Homininae and future studies might attempt to investigate whether the anatomical shape associations among carpals are functionally related to locomotion and manipulation.

Background/Objectives Bowel endometriosis (BE) is defined as the presence of endometrial-like tissue in the muscular layer of the bowel wall. When BE does not cause severe obstruction to fecal transit, not leading to (sub)occlusive symptoms, the decision to operate becomes challenging as intestinal surgery is associated with higher complication rates and long-term bowel dysfunction. The aim of this cross-sectional study is to evaluate the quality of life (QoL) in patients with BE undergoing medical therapy or expectant management, investigating the impact of characteristics of BE nodules on QoL and intestinal function. Methods A retrospective cross-sectional analysis was conducted on 580 patients with BE who did not undergo surgery but were treated conservatively by medical therapy or expectant management between January 2017 and August 2022. The diagnosis of BE was done by transvaginal ultrasound and confirmed at double contrast barium enema. After at least one year of follow-up, QoL and intestinal function of patients were evaluated by the Endometriosis Health Profile-5 (EHP-5) questionnaire and Bowel Endometriosis Symptom score (BENS), whereas pain symptoms were assessed by the Visual Analogic Scale (VAS 0-10). Statistical analysis was performed to investigate possible associations between QoL and characteristics of bowel nodules (dimension, location, and evidence of stenosis) as well as type and length of eventual medical therapy. Results Patients with BE had a satisfying overall QoL with a mean EHP-5 score of 105.42 ± 99.98 points and VAS lower than 3 for all pain domains; additionally, they did not show a significant impartment of bowel function with mean BENS score of 4.89 ± 5.28 points. Notably, patients under medical therapy had a better QoL than patients without therapy (p

The role of foods is shifting from focusing on the provision of energy and basic nutrients to also include bioactive compounds that prevent the development of chronic age-related diseases. Mi-croalgae offer a source of nutritional compounds with important health effects, and have the po-tential for production of health-promoting products, without increasing agricultural land use and negatively impacting the environment. Here we investigate the health effects of microalgal ex-tracts with high levels of the colourless carotenoid phytoene. Phytoene is widely available from dietary sources and can be detected across different tissues in the human body. However, it is usually regarded as a precursor for the synthesis of other carotenoids, rather than a bioactive molecule. We utilised the model organism C. elegans to show that phytoene-rich extracts from Chlorella sorokiniana and Dunaliella bardawil have anti-ageing properties. The extracts protect against oxidative damage and amyloid-β42 proteotoxicity (a major pathology of Alzheimer's disease), and extends lifespan. We show that pure phytoene also has these anti-ageing effects, suggesting that phytoene is a bioactive molecule with positive effects on ageing and longevity.

The influence of humic aggregates in water solution upon the chemical stability under basic conditions of different substrates has been reviewed. The kinetic behavior of each substrate has been modelized in terms of micellar pseudophase model.

Learning systems have been very focused on creating models that are capable of obtaining the best results in error metrics. Recently, the focus has shifted to improvement in order to interpret and explain their results. The need for interpretation is greater when these models are used to support decision making. In some areas this becomes an indispensable requirement, such as in medicine. This paper focuses on the prediction of cardiovascular disease by analyzing the well-known Statlog (Heart) Data Set from the UCI’s Automated Learning Repository. This study will analyze the cost of making predictions easier to interpret by reducing the number of features that explain the classification of health status versus the cost in accuracy. It will be analyzed on a large set of classification techniques and performance metrics. Demonstrating that it is possible to make explainable and reliable models that have a good commitment to predictive performance.

The aim of this study was to identify gender differences in technical-tactical behaviour in football. To this end 68 matches of the first division of the Spanish men’s and women´s league, corresponding to 2016/17 season were analyzed. A comparison of medians was carried out using the Mann-Whitney U-test were conducted as post hoc test and a grouping of the variables through the clustering bootstrapping technique in both groups. We have detected statistically significant differences regarding all accurate passes, in favour of men, as well as a greater number of yellow cards. In female football, a greater number of picking up free balls, interceptions, lost balls, recoveries, challenges and attacks, both positional and counterattacks, are produced. The clustering analysis also allowed that in male football, the circumstance of receiving a red card is closely related to the number of goals conceded and most of the shots on goal are achieved by positional attacks. In women's football, ball possession on own half is closely related to the number of losses. These results could be useful for gender-specific training information for optimal preparation. However, more research is warranted to establish the main gender differences and characterize women's football.

Inflammatory Bowel Disease (IBD) presents distinct challenges during pregnancy due to its influence on maternal health and pregnancy outcomes. This literature review aims to dissect the existing scientific evidence on pregnancy in women with IBD and provide evidence-based recommendations for clinical management. A comprehensive search was conducted across scientific databases, selecting clinical studies, systematic reviews, and other pertinent resources. Numerous studies have underscored an increased risk of complications during pregnancy for women with IBD, including preterm birth, low birth weight, neonates small for gestational age, and congenital malformations. Nevertheless, it's evident that proactive disease management before and throughout pregnancy can mitigate these risks. Continuation of IBD treatment during pregnancy and breastfeeding is deemed safe with agents like thiopurines, anti-TNF, vedolizumab, or ustekinumab. However, there's a call for caution when combining treatments due to the heightened risk of severe infections in the first year of life. For small molecules, their use is advised against in both scenarios. Effective disease management, minimizing disease activity, and interdisciplinary care are pivotal in attending to women with IBD. The emphasis is placed on the continual assessment of maternal and infant outcomes and an expressed need for further research to enhance the understanding of the ties between IBD and adverse pregnancy outcomes.

Treatment of the [AuCl(tetrahydrothiophene)] complex with 4-chloro-2-iodo-1-isocyanobenzene furnished the gold(I) compound [AuCl(CNC6H3-4-Cl-2-I)] (1). In the crystal structure of 1, the linear C–Au–Cl group is subject to the solid-state head-to-tail pairing which is determined by the aurophilic Au···Au and the rare π-holeCN···Cl interactions. These two types of structure-determining interactions are complementary to each other and the system of Au···Au and CCN···Cl contacts accomplishes 2D extended ladder-type architecture. In addition, the terminal I-atoms are involved in the three-center halogen bonding. Density functional theory calculations, employing a set of computational tools, verified the role of Au···Au and π-holeCN···Cl noncovalent bonds in the spectrum of noncovalent forces.

Although there are extensive literature reports on the use of gold nanoparticle (AuNP) based homogeneous assays for detection of biomolecules, very few experimental description and procedures involving their preparation are described. In this study, AuNPs conjugated to Bovine Serum Albumin or Envelope protein from Dengue II were developed as a homogeneous immunoassay for antibody detection. We report here optimization of key parameters to prepare an immunoassay like conjugation protein concentration, centrifugation time, electrolyte addition and assay temperature. We determined that saturating protein concentrations improved AuNPs surface coverage and uniformity of the assay and addition of sodium chloride improved sensitivity of the antibody detection method and assay stability. Furthermore, we showed that dynamic light scattering can be used to monitor changes in gold nanoparticles in the preparation and detection steps. Additionally, numerical simulations of the plasmonic optical response of AuNPs were carried out to scan for size-dependent response of the AuNPs. The AuNPs homogeneous immunoassay developed was further used in the detection of antibodies in vitro to detect Dengue virus infection.

The critical systems, which the failure and malfunction may result in human, environment and financial severe damages, are essential components in various sectors and particularly in energy domains. Although unwished, integration error problems in supervision of critical systems occurs, incurring significant expenses because of operator’s subjective analysis and on hardware topology failures. In this work, a malleable model design approach is proposed to formulate and solve the integration error problem in the critical systems supervision in terms of reliability. A real Hybrid Power Plant (HPP) case is considered as a requirement for a study case with simulated data. A method framework with informal approach (C4 diagram) and formal approach (Hierarchical Coloured Petri Nets) in radial spectrum is applied to the HPP supervision design. Using formal methods, a formulation and solution to this problem through structured, scalable and compact mathematical representations are possible. This malleable model intends to guarantee functional correctness and then reliability of the plant supervision system based on system software architecture. Outcomes suggest corroboration that the malleable model is appropriate for energy domain, and can be used for other types of critical systems, bringing all the benefits of this methodology to the context in which it will be applied.

Rare Earth Elements (REE), also known as Lanthanides (Ln3+), are a group of 17 elements showing peculiar physical and chemical properties. Unlike technological applications, very little is known about the physiological role and toxicity of Ln3+ on biological systems, in particular on microorganisms (e.g., bacteria), which represent the most abundant domains on our planet. Up to now, very limited studies have been conducted due to Ln3+ precipitation with some anions commonly present in the culture media. Therefore, the development of a minimal medium is essential to allow the study of Ln3+-microbial interactions, limiting considerably the precipitation as insoluble salts. In this regard, a new minimal culture medium capable of solubilizing large amounts of Ln3+, and allowing the growth of different microbial taxa, was successfully developed. Assays have shown that the medium is capable of solubilizing Ln3+ up to 100 times more than other common culture media and allowed the growth of 63 bacteria and 5 fungi. The kinetic growth of one yeast and one gram-positive bacterium has been defined, proving to support superior growth and biomass compared to other commonly used minimal media. Moreover, the sensitivity and uptake/absorption of a Bacillus stratosphericus strain was tested, highlighting its capability to tolerate concentrations up to 10 mM of either Cerium, Gadolinium or Lanthanum and accumulate different quantities of the three.

Rising antimicrobial resistance (AMR) in Salmonella serotypes host-adapted to cattle is of increasing concern to the beef and dairy industry. The bulk of the existing literature focuses on AMR post-slaughter. In comparison, the understanding of AMR in Salmonella among pre-harvest cattle is still limited, particularly in Texas, which ranks top five in beef and dairy exports in the United States; inherently, the health of Texas cattle has nationwide implications for the health of the United States beef and dairy industry. In this study, long-read whole genome sequencing and bioinformatic methods were utilized to analyze antimicrobial resistance genes (ARGs) in 98 isolates from beef and dairy cattle in the Texas Panhandle. Fisher exact tests and elastic net models accounting for population structure were used to infer associations between ARGs and antimicrobial phenotypic profiles and metadata. Gene mapping was also performed to assess the role of mobile genetic elements in harboring ARGs. ARG were found to be statistically different between the type of cattle operation and Salmonella serotypes. Beef operations were statistically significantly associated with more resistance genes compared to dairy operations. Salmonella Heidelberg, followed by Salmonella Dublin isolates, were associated with the most ARGs. Additionally, specific classes of ARGs were only present within mobile genetic elements.

Current antibiograms cannot discern the particular effect of a specific antibiotic when the bacteria are incubated with a mixture of antibiotics. To prove that this task is achievable, Escherichia coli strains were treated with ciprofloxacin for 45 min, immobilized on a slide and stained with SYBR Gold. In susceptible strains, the nucleoid relative surface started to decrease near the MIC, being progressively condensed as dose increased. The shrinkage level correlated with the DNA fragmentation degree. Ciprofloxacin-resistant bacilli showed no change. Additionally, E. coli strains were incubated with ampicillin for 45 min and processed similarly. The ampicillin-susceptible strain revealed intercellular DNA fragments that increased with dose, unlike the resistant strain. Co-incubation with both antibiotics revealed that ampicillin did not modify the nucleoid condensation effect of ciprofloxacin, whereas the quinolone partially decreased the background of DNA fragments induced by ampicillin. Sixty clinical isolates, with different combinations of susceptibility-resistance to each antibiotic, were co-incubated with the EUCAST breakpoints of susceptibility of ciprofloxacin and ampicillin. The morphological assay correctly categorized all the strains for each antibiotic in 60 min, demonstrating the feasible independent evaluation of a mixture of quinolone and beta-lactam. The rapid phenotypic assay may shorten the incubation times and necessary microbial mass currently required for evaluation.

The dawn of Artificial Intelligence (AI) in healthcare stands as a milestone in medical innovation. A plethora of different medical fields are heavily involved and pediatric emergency medicine is no exception. These new tools do not merely provide more advanced and efficient systems for patients’ diagnosis, management and treatment. They rather concern a strict shift from traditional methods based upon broad categories towards a more personalized healthcare. AI offers many promises in pediatric emergency medicine with a wide range of applications involving clinical decision making, patients’ flows management and prioritization. Main barriers to a widespread diffusion involve technological challenges but also ethical issues and the paucity of extensive datasets in pediatric contexts. We conducted a narrative review structured in two parts. The first part explores the theoretical principles of AI, providing all the necessary background to feel confident with these new state-of-the-art tools. The second part presents an informative analysis of AI models in pediatric emergencies, pointing out the actual applications and challenges until future feasible research perspectives.

Nowadays, inherently safer designs are considered as key priorities to prevent or mitigate serious incidents with devastating consequences. The need for process safety assessment during early design phases has motivated the development of several contributions related to computer-aided assessment methodologies in order to measure the inherent safety of chemical processes. In this work, the large-scale production of chitosan from shrimp wastes was evaluated from process safety point of view using the numerical descriptive inherent safety technique (NuDIST).To this end, simulation of the chitosan production was performed using Aspen Plus ® to obtain extended mass and energy balances. The assessment of all the chemicals involved within the process was carried out for the following safety parameters: explosivity (EXP), flammability (FL) and toxicity (TOX). The safety assessment of the process included the parameters of temperature (T), pressure (P) and heat of reaction (HR). The maximum chemical safety score was estimated in 171.01 with ethanol as main contributor to the parameter of explosivity and flammability. The score associated with operating data was calculated in 209.30 and heat of reaction reported to be the most affecting parameter. The NuDIST score was estimated in 380.30. This NuDIST value revealed the low hazards associated with the handling of substances such as shrimp wastes, chitosan and water, as well as the non-extreme temperature and pressure conditions. In general, the large-scale production of chitosan from shrimp shells showed to be an inherently safe alternative of waste valorization.

The acoustic conditions of open-plan office spaces influence wellbeing and productivity perceived by users, but with an inadequate evaluation for workspace, acoustic design in open-plan offices can be a factor that alters user performance. Such is the case in Mexico, where there are no adequate standards to evaluate specific acoustic conditions such as intelligibility. For this reason, this case study aims to evaluate different types of measurement methods for intelligibility. This study was carried out in a university in northern Mexico. The sound measurements were based on the Mexican standard for noise analysis and the ISO 3382- part 3 standards for acoustic measurements for open-plan offices. The psychoacoustic parameters evaluated were Reverberation and Intelligibility, using objective methods determined on S/N and subjective methods based on loss of consonant; where it was analyzed distance between sound source and zones classified by building design characteristics. The results indicated in which points the intelligibility effects increased, observing that Reverberation remained stable in this office, and that the subjective methods presented greater size of the measured sound effect than the objective methods. This finding establishes that subjective methods conformed to Lognormal behavior, which is applicable to other linguistic elements describing speech behavior.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

Inflammation is considered an important target for stroke therapy because it induces secondary brain damage after the initial ischemic insult. Peripheral monocytes migrate to the brain parenchyma after a central insult. They then differentiate to macrophages in a positive feedback fashion contributing to damage instead of ischemic resolution and inflammation control. A cyclic diterpenoid, (1S,2E,4R,6R,7E,11E)-cembra-2,7,11-triene-4,6-diol (4R), decreases neurodegeneration after ischemia with central anti-inflammatory activity. This study aims to determine whether the central anti-inflammatory effect of 4R is effective against peripheral inflammation triggered by brain ischemia. To investigate the anti-inflammatory effect of 4R, we treated macrophages with lipopolysaccharide (LPS) as an inflammatory model, followed by treatment with 4R. Microarray transcriptome analysis of over 30,000 genes identified the differential expression of 393 genes. Genes related to inflammation, cell adhesion, and transcription were validated with qPCR, and reduced expression was determined. Quantification of NF-kB phosphorylation served as a marker for the modulation of inflammation through gene transcription. Our results show that 4R was associated with a reduction in NFKB1 and ITGB5 gene expression, increased phosphorylation of NF-kB, and a decrease in macrophage adhesion in a blood-brain barrier model. These results indicate that 4R can partially modulate the peripheral immune response, making 4R a potential drug against post-ischemic inflammation.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

Background In this study we investigated in detail the role of cannabidiol (CBD), Beta-caryophyllene (BC), or their combinations in diabetic peripheral neuropathy (DN). The key factors that contribute to DN include mitochondrial dysfunction, inflammation, and oxidative stress. Methods Briefly, Streptozotocin (STZ) (55 mg/kg) was injected intraperitoneally to induce DN in Sprague Dawley rats and performed procedures including Randall Sellito Calipers, Von Frey Aesthesiometer, hot plate, and cold plate methods to determine mechanical and thermal hyperalgesia in vivo. The blood flow to the nerves was assessed by using the Laser Doppler device. Schwann cells were exposed to high glucose (HG) at a dose of 30 mM to induce hyperglycemia and DCFDA, JC1 & Mitosox staining were done to determine mitochondrial membrane potential, reactive oxygen species and mitochondrial superoxides in-vitro. The rats were administered i.p with BC (30mg/kg), CBD (15mg/kg), or combination while Schwann cells were treated with 3.65 µM CBD, 75 µM BC, or combination to assess their role in DN amelioration. Results Our results revealed that exposure to BC and CBD diminished HG-induced hyperglycemia in Schwann cells, in part, through reducing mitochondrial membrane potential, reactive oxygen species and mitochondrial superoxides. Further, BC and CBD combination treatment in-vivo could prevent the deterioration of mitochondrial quality control system by promoting autophagy and mitochondrial biogenesis while improving blood flow. CBD and BC treatments also reduced pain hypersensitivity to hyperalgesia and allodynia with increased antioxidant and anti-inflammatory action in diabetic rats. These in vivo effects were attributed to significant upregulation of AMPK, SIRT3, Nrf2, PINK1, PARKIN, LC3B, Beclin1 and TFAM functions while downregulation of NLRP3 inflammasome, NFκB, COX2 and p62 activity was noted as determined by western blotting. Conclusion the present studies demonstrated that STZ & HG induced oxidative and nitrosative stress play a crucial role in the pathogenesis of diabetic neuropathy. We find, for the first time, that CBD and BC combination ameliorate DN via modulating the mitochondrial quality control system.

A hallmark of Alzheimer’s disease (AD) are the proteinaceous aggregates formed by the amyloid-beta peptide (Aβ) that is deposited inside the brain as amyloid plaques. The accumulation of aggregated Aβ may initiate or enhance pathologic processes in AD. According to the amyloid hypothesis any agent that has the capability to inhibit Aβ aggregation and/or destroy amyloid plaques represents a potential disease modifying drug. In 2023, a humanized IgG1 monoclonal antibody (lecanemab) against the Aβ soluble protofibrils was approved by US FDA for AD therapy thus providing compelling support to the amyloid hypothesis. To acquire a deeper insight on the in vivo Aβ aggregation, various animal models, including aged herbivores and carnivores, non-human primates, transgenic rodents, fish and worms are widely exploited. This review is based on the recent data obtained using transgenic animal AD models and presents experimental verification of the critical role in Aβ aggregation seeding of the interactions between zinc ions, Aβ with the isomerized Asp7 (isoD7- Aβ) and the α4β2 nicotinic acetylcholine receptor.

Background: Meniere disease (MD) is an inner ear disorder associated with comorbidities such as autoimmune diseases or migraine. This study describes clinical and cytokine profile in MD according to the age of onset of the condition. Methods: A cross-sectional study including 83 MD patients: 44 with early onset MD (EOMD, <35 years old), and 39 with late onset MD (LOMD, > 50 years old), 64 patients with migraine and 55 controls was carried out. Clinical variables and cytokines levels of CCL3, CCL4, CCL18, CCL22, CXCL1 and IL-1β were compared among the different groups. Results: CCL18 levels were higher in patients with migraine or MD than in controls. Elevated levels of IL-1β were observed in 11.4% EOMD and in 10.3% LOMD patients and these levels were not dependent on the age of individuals. EOMD had a longer duration of the disease (p=0.004) and a higher prevalence of migraine than LOMD (p=0.045). Conclusions: Patients with EOMD have a higher prevalence of migraine than LOMD, but migraine is not associated with any cytokine profile in patients with MD. The levels of CCL18, CCL3 and CXCL4 were different between patients with MD or migraine and controls.

The Indian meal moth, Plodia interpunctella, poses a significant threat to global agricultural products. Although pheromone-based technologies show promise for P. interpunctella management, limitations like single-sex targeting necessitate exploring complementary strategies. Vegetable-based oils represent a potential alternative, but their efficacy, sex-specificity, and interaction with sex pheromones remain unclear. To answer these questions, we first examined attraction of P. interpunctella female and male adults to ten different vegetable oils, i.e., camellia, corn, olive, peanut, rapeseed, sesame, soybean, sunflower, walnut, and a blended oil (mixture of sunflower seed, rapeseed, soybean, peanut, and sesame oils), in the semi-field conditions. Sesame, olive, and blended oils demonstrated most attractive, capturing significantly more adults compared to other oils. We then evaluated effectiveness of these three attractive oils and their combinations with P. interpunctella sex pheromone in a grain warehouse. Traps baited with these oils captured significantly more females and males compared to control traps without attractants. However, sex pheromone addition did not improve male capture and significantly reduced female capture, suggesting an inhibitory effect. Our findings highlight the potential of blended, olive, or sesame oil trap alone as alternative monitoring and trapping tools for P. interpunctella, delivering novel insights into the development of efficient integrated pest management strategies for stored products.

This article addresses the problem of formation control of a quadrotor and one (or more) marine vehicles operating at the surface of the water with the end goal of encircling the boundary of a chemical spill, enabling such vehicles to carry and release chemical dispersants used during ocean cleanup missions to break-up oil molecules. Firstly, the mathematical models of the Medusa class of marine robots and quadrotor aircrafts are introduced, followed by the design of single vehicle motion controllers that allow these vehicles to follow a parameterized path individually using Lyapunov based techniques. At a second stage, a distributed controller using event triggered communications is introduced, enabling the vehicles to perform cooperative path following missions according to a pre-defined geometric formation. In the next step, a real time path planning algorithm is developed that makes use of a camera sensor, installed on-board the quadrotor. This sensor enables the detection in the image of which pixels encode parts of a chemical spill boundary and use them to generate and update in real time a set of smooth B-spline based paths for all the vehicles to follow cooperatively. The performance of the complete system is evaluated by resorting to 3-D simulation software, making it possible to simulate visually a chemical spill. Results from real water trials are also provided for parts of the system, where two Medusa vehicles are required to perform a static lawn-mowing path following mission cooperatively at the surface of the water.

We present a very computationally light and fast approximation algorithm and then verify it with genetic algorithm and simulated annealing. We show that our algorithm is on par with GA and SA in terms of output produced while having a tightly bounded time complexity. Our algorithm works best when there is a strong positive correlation between the reliability of a component and its cost. We present two algorithms with the same essence. One of them is system cost bounded and the other is target reliability bounded. Our proposed algorithm works on a subsystem level redundancy instead of component level redundancy.

This work describes a resonance Raman study performed in domes of monolayer MoS2 using 23 different laser excitation energies covering the visible and near-infrared (NIR) ranges. The multiple-excitation results allowed us to investigate the exciton-phonon interactions of different phonons (A1’, E’ and LA) with different electronic and excitonic optical transitions in biaxially strained monolayer MoS2. The analysis of the intensities of the two first-order peaks, A1’ and E’, and the double-resonance 2LA Raman band as a function of the laser excitation furnished the values of the energies of the indirect gap and the excitonic transitions in the strained MoS2 domes. It was noticed that the out-of-plane A1’ phonon mode is significantly enhanced only by the indirect gap I and the C exciton, whereas the in-plane E’ mode is only enhanced by the C exciton of MoS2 dome, revealing thus a weak interaction of these phonons with the A and B excitons in the strained MoS2 domes. On the other hand, the 2LA Raman band is significantly enhanced at the indirect gap I transition and by the A (or B) exciton, but not enhanced by the C exciton, showing thus that the LA edge-phonons that participate in the double resonance process in MoS2 have a weak interaction with the C exciton.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Oritavancin is a novel long-acting lipoglycopeptide with in vitro activity against methicillin-resistant (MR) Gram-positive pathogens and a good bactericidal activity even in presence of biofilm forming bacteria. It has been approved for acute bacterial skin and skin structure infections (ABSSSI), but recent reports have demonstrated possible off-label uses, as for prosthetic joint infections (PJI), which, in more than half of cases, are caused by MR Gram positive organisms. We reported a case of a man in his eighties with a late shoulder PJI caused by methicillin resistant Staphyloccus epidermidis (MRSE) with contraindications for surgical replacement and few oral therapeutic options for a long term suppressive antibiotic therapy. The prosthesis was retained, and the patient received ten outpatient sequential doses of 1200 mg of oritavancin during 28 weeks, based on therapeutic drug monitoring (TDM) as a guide for correct timing of administration of each dose. During oritavancin administration, the patient achieved clinical cure, with disappearance of the pain and regaining pre-infection joint mobility, with no side effects reported and no further surgery or hospitalization needed. The treatment is ongoing as a long-lasting suppressive antimicrobial therapy. Oritavancin could represent an excellent solution for treating PJI caused by MR organism, especially in patients who need a long-term suppressive therapy.

Metabolic Associated Steatohepatitis Liver Disease (MASLD) currently impacts a quarter of the global population and its prevalence is expected to increase in the future. As a result, the incidence of hepatocellular carcinoma associated with MASLD is also on the rise. Notably, hepatocellular carcinoma in this group does not always develop alongside liver cirrhosis, often leading to a more advanced stage at diagnosis. The challenge lies in accurately identifying patients who are at a higher risk of hepatocellular carcinoma to tailor screening processes effectively. Additionally, several therapeutic approaches are being explored to prevent hepatocellular carcinoma, although there are yet no universally accepted guidelines

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

While digitization can make the health industry faster and more efficient, there are many financial, social and organizational obstacles and barriers to its implementation. This article offers a systematic review of the main troubles detected from the literature review. Also there is a proposal of new kind of restrictions to pay attention. Finally, its offer an heterodox reading about the problem analyzed.

Various distance metrics and their induced norms are employed in the quantitative modeling of evolutionary dynamics. Minimization of these distance metrics when applied to evolutionary optimization are hypothesized to result in different outcomes. Here, we apply the different distance metrics to the evolutionary trait dynamics brought about by the interaction between two competing species infected by parasites (exploiters). We present deterministic cases showing the distinctive selection outcomes under the Manhattan, Euclidean and Chebyshev norms. Specifically, we show how they differ in the time of convergence to the desired optima (e.g., no disease), and in the egalitarian sharing of carrying capacity between the competing species. However, when randomness is introduced to the population dynamics of parasites and to the trait dynamics of the competing species, the distinctive characteristics of the outcomes under the three norms become indistinguishable. Our results provide theoretical cases when evolutionary dynamics using different distance metrics exhibit similar outcomes.

Aedes scapularis is a neotropical mosquito known to transmit pathogens of medical and veterinary importance. Its recent establishment in southeastern Florida has potential public health implications. We used an ecological niche modeling approach to predict the abiotic environmental suitability for Ae. scapularis across much of the Americas and Caribbean Islands. Georeferenced occurrence data obtained from the Global Biodiversity Inventory Facility and recent collection records of Ae. scapularis from southern Florida served as input for model calibration. Environmental layers included bioclimatic variables provided in 2000 to 2010 average Modern Era Retrospective-analysis for Research and Applications climatic (MERRAclim) data. Models were run in the software program Maxent. Isothermality values found often in costal environments contributed strongest to model performance. Model projections suggested areas predicted suitable for Ae. scapularis across portions of the Amazon Basin, the Yucatán Peninsula, the Florida Peninsula, and multiple Caribbean Islands. Additionally, model predictions suggested connectivity of highly suitable or relatively suitable environments spanning the United States Gulf Coast, which may facilitate geographic expansion of this species. At least sixteen Florida counties were predicted highly suitable for Ae. scapularis, suggesting vigilance is needed by vector control and public health agencies to recognize further spread of this vector.

With the growing demand for personal protective equipment (PPE) in the face of the pandemic events caused by SARS-COV-2, the opportunity arises for the development of materials with characteristics such as antimicrobial, antiviral, antifungal activity, etc. The use of polymeric nanocomposites based on polyester/copper offers an alternative of great interest due to the versatility of the raw material and the high efficiency of copper as an antimicrobial additive. In this study, textile fibers prototypes with different Cu nanoparticles (CuNP) content were produced using melt-spinning to obtain bi-component multifilament fibers, and melt-blowing to obtain non-woven fabrics. The prototypes were tested against different pathogenic microorganisms such as S. aureus, E. coli, and C. albicans. It was shown that bi-component fibers offer more excellent protection against pathogens, while non-woven fabric only shows activity against E. coli. It was possible to identify that the CuNP were confined exclusively in the outer cover of the bi-component fibers, using different analytical techniques, which may be associated with the increase in antimicrobial activity, compared to the fibers present in the non-woven fabric, even when they present the same CuNP content.

Lower back musculoskeletal disorders (MSD) are an important public health problem and the leading cause of disability worldwide, but with prevalence yet unknown among shellfish gatherers. To investigate the prevalence and work-related factors associated with lower back MSD in a population of female shellfish gatherers, an epidemiological cross-sectional study was carried out in Saubara, Bahia – Brazil, in 2013. The Brazilian version of the Job Content Questionnaire (JCQ) and the Nordic Musculoskeletal Questionnaire (NMQ), in addition to a questionnaire containing the physical demands adapted to the artisanal work, were applied to a random sample of 209 female shellfish gatherers. The prevalence of lower back MSD was 72.7%. Using multivariate logistic regression, the shellfish gatherers who had worked for more than 26 years in the activity showed a prevalence of 1.22 (95% CI: 1.04-1.44) times higher compared to those unexposed. Lower back MSD was 1.24 (95%CI: 1.08-1.42) times higher among those more exposed to work sitting with trunk flexion. Those performed manual handling and muscle force with the arms had a prevalence ratio of 1.18 (95%CI: 1.01-1.39). These results show the need for greater awareness of health and social welfare factors impacting workers in small-scale fisheries and will promote the elaboration of health care policies for this occupational class.

The Musa textilis var. Abuab has high fiber quality (FQ) but has low resistance against abaca bunchy top virus (AbBTV); the Musa balbisiana var. Pacol, has low FQ but high resistance against AbBTV. Their backcrosses (BC2 and BC3) possess both desirable traits. Analysis using RNA-seq showed that the regulatory divergence of Abuab and Pacol is largely explained by cis differences with 27.4% and 22.3% if we are to assess it using BC2 and BC3, respectively. Cis differences between the two genotypes are significantly reduced from BC2 to BC3 due to changes in genomic constitution. Trans, on the other hand, is robust to changes in allelic composition. All these are attributed to the loss of heterozygosity in the BC3 relative to BC2. Further analysis showed that both backcrosses exhibited genome-wide preferential expression of Pacol- over Abuab-specific alleles, despite the wider genetic presence of the latter in the hybrids. The ratio of the two genotype-specific expressed transcripts and the ratio of their corresponding genetic make-up are significantly disproportionate, a phenomenon which we refer here as “genome–transcriptome incongruence”. We also observed preferential expression switching in which several genes prefer Abuab- (or Pacol-) specific allele in the BC2 but switched to Pacol- (or Abuab-) specific allele in the BC3 genome.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

Cotton is the most ubiquitous and profitable fiber with diverse industrial and domestic applications. Grown in over 100 countries, it has a global market value of about $40 billion and employs over 350 million people from fields to textile mills, contributing about 7% of total labor-force recruitment in developing economies. Cotton has an indeterminate growth habit and an extensive tap root system affected by soil physicochemical and environmental conditions. There is a consensus among experts that conventional cotton cultivation still has a long way to attain sustainability, which is essential if cotton will maintain its competitive edge over other natural and synthetic fibers like hemp, polyesters, and rayon. Despite several efforts already committed to growing cotton sustainably, sustainability has eluded cotton cultivation globally because of the intense farm inputs (freshwater, pesticides, and heavy-duty equipment) needs, especially in developing economies. Some of the technological advancements towards achieving the goal of sustainable cotton cultivation include the development of new varieties, improved irrigation and mulching and precision agriculture techniques, application of remote sensing and Unmanned Aerial Systems (UAS) combined with image processing, and the introduction of autonomous and multi-purpose robotic platforms for growing and harvesting cotton. This review attempts to evaluate the successes already achieved by stakeholders in moving cotton towards sustainable production and identify areas where efforts are still needed to reach sustainable production and improved profitability goals for cotton with projections for future research directions.

Aimed to obtain purple garlic varieties, 360 bolting bulbs from the Protected Geographical Indication (PGI) “Las Pedroñeras” were selected for their size, and the presence of abundant external scales. After a further selection, 243 out of the 360 bulbs were discarded due to undesired characteristics, as light purple color, high number of small cloves, cloves affected by Fusarium spp. and mites, among other. It was stablished that each bulb would give rise to a family. Thus, 117 families were planted under a random design during season 2021-2022. Either physiological, morphological and phenological traits were assessed for each family, and the affectations by pest and pathogens were also controlled. After the assessment of this trial, 103 out 117 families remained in the program, and were used for the establishment of a second trial the next season. Unlike the first trial, after the evaluations only 23 families remained in the program. There was observed a high variability for most of traits, with a great influence of families. The phenotypic behavior of families was significative influenced by environment, highlighting the need of their assessment under different environmental conditions. The high variability registered for the target sample, opens the possibility to select new garlic varieties from this PGI.

Fibroblast activation protein (FAP) is a membrane-tethered serine protease overexpressed in the reactive stromal fibroblasts of &gt; 90% human carcinomas, which makes it a promising target for developing radiopharmaceuticals for imaging and therapy of carcinomas. Here, we synthesized two novel (R)-pyrrolidin-2-yl-boronic acid-based FAP-targeted ligands; SB02055 (DOTA-conjugated (R)-(1-((6-(3-(piperazin-1-yl)propoxy)quinoline-4-carbonyl)glycyl)pyrrolidin-2-yl)boronic acid) and SB04028 (DOTA-conjugated ((R)-1-((6-(3-(piperazin-1-yl)propoxy)quinoline-4-carbonyl)-D-alanyl)pyrrolidin-2-yl)boronic acid). natGa- and 68Ga-complexes of both ligands were evaluated in preclinical studies and compared to previously reported natGa/68Ga-complexed PNT6555. Enzymatic assays showed that FAP binding affinities (IC50) of natGa-SB02055, natGa-SB04028 and natGa-PNT6555 were 0.41±0.06, 13.9±1.29 and 78.1±4.59 nM, respectively. PET imaging and biodistribution studies in HEK293T:hFAP tumor-bearing mice showed that while [68Ga]Ga-SB02055 presented with a nominal tumor uptake (1.08±0.37 %ID/g), [68Ga]Ga-SB04028 demonstrated clear tumor visualization with ~1.5-fold higher tumor uptake (10.1±0.42 %ID/g) compared to [68Ga]Ga-PNT6555 (6.38±0.45 %ID/g). High accumulation in the bladder indicated renal excretion of all three tracers. [68Ga]Ga-SB04028 displayed low background level uptake in most normal organs, and comparable to [68Ga]Ga-PNT6555. However, since its tumor uptake was considerably higher than [68Ga]Ga-PNT6555, the corresponding tumor-to-organ uptake ratios for [68Ga]Ga-SB04028 were also significantly greater than [68Ga]Ga-PNT6555. Our data demonstrate that (R)-(((quinoline-4-carbonyl)-D-alanyl)pyrrolidin-2-yl)boronic acid is a promising pharmacophore for the design of FAP-targeted radiopharmaceuticals for cancer imaging and radioligand therapy.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

Indoor environmental comfort is fundamental to human health as people spend 90% of their time indoors. This aspect is even more crucial in hospitals, where the concept of health is closely linked to well-being, ethics, and environmental aspects. Emerging methodologies and technologies such as Digital Twin, Building Information Modeling, the Internet of Things, sensing technologies, and data analytics offer new opportunities to ensure healthier environments and more efficient building management. This paper provides an assessment of how digitalization can support decision-making processes related to maintaining high levels of indoor environmental comfort in hospital settings, particularly by analyzing how real-time data processing and the application of machine learning can promote proactive interventions in these facilities. The methodological approach was based on four phases: defining the objectives of the digital twin, identifying the input data to build and feed the digital model, defining the KPIs to evaluate the system's correct functioning, and identifying the enabling technologies to be integrated into the system to achieve the set goal. The result is a digital twin for managing the operating room and its related services, with the aim of guiding decisions based on accurate data and improving operational efficiency, levels of environmental comfort, and safety regarding the diffusion of medical gases.

For children born with congenital heart defects (CHD), extracorporeal life support may be necessary. This study aimed to investigate the outcomes of children on extracorporeal membrane oxygenation (ECMO), focusing on various risk factors, including the type of CHD. The study was conducted as a retrospective single-center analysis at the Children's Hospital Zurich. All patients with CHD who required ECMO (veno-arterial or veno-venous) between 2009 and 2019 were included. Among the 88 patients, 36 (41%) had a single ventricle heart defect while 52 (59%) had a biventricular heart defect. Out of the total patients, 25 (28%) survived, with 7 (8%) having a single ventricle heart defect and 18 (20%) having a biventricular heart defect. Statistical analysis with a p-value of 0.19 revealed no significant difference in survival rates between the two groups. At the one-year follow-up, all children who survived to discharge were still alive. The rate of complications on ECMO was higher in children with a single ventricle (odds ratio [OR] 1.57, 95% confidence interval [CI] 0.67 - 3.7). The occurrence of a second ECMO run was more frequent in patients with a single ventricle compared to those with a biventricular physiology (22% vs. 9.6%). Although the study did not identify a significant difference in survival rates, it did indicate that patients with a single ventricle faced a higher risk of complications during ECMO and a greater likelihood of requiring a second ECMO run.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

The ability of S. aureus to infect humans and cause a wide range of infections so efficiently is a consequence of the many variant virulence factors that it can produce. Superantigens (SAgs) make up a group of them and include staphylococcal enterotoxins (SE). The main objective of this study was to detect enterotoxin gene cluster (EGC) in S. aureus isolates that caused infections in Paraguayan children in the year 2017, through an observational and cross-sectional study. The detection of the EGC including the seg, sei, sem, sen, seo, and seu genes, was carried out by end-point PCR. 181 S. aureus isolates were collected, most of them caused skin and soft tissue infections (SSTI, n=140, 77%) and came from children under 6 years 50% (n=90). At least one SE gene was detected in 96% (174/181) of isolates and 24% (44/181) carried the entire EGC. An association between methicillin resistance and seg, sei, seo, and seu gene carriage (p ≤0.05) was observed. A high prevalence of EGC was detected in S. aureus isolates collected from infected children attending the main health care centers in Paraguay, its importance is due to the potential of these toxins to aggravate staphylococcal infections.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

Three autonomous communities have been the ones that, in the 2022-2023 season, anticipated the document approved by the Public Health Commission, recommending influenza vaccination for all children aged 6 to 59 months. The main objective of this work is to evaluate the attitude of healthcare professionals towards the first universal vaccination campaign in our region, as well as the acceptability of the vaccines used and the attitude towards the piloting of school vaccination. Cross-sectional, survey-based, descriptive study. All healthcare professionals involved in the campaign were invited to participate. The 91.9% of surveyed professionals thought that flu vaccination from 6 to 59 months was important or very important. 89.8% had previous experience regarding the intramuscular vaccine. The professionals valued the intranasal vaccine significantly more positively; however, there were no differences when asking for each of the vaccines without comparison. The inhaled vaccine was preferred by 97.5% for the following campaign. Piloted school vaccination showed 75% acceptance. The inhaled vaccine was preferred by most professionals and the piloted school vaccination was highly accepted, and independently associated to the importance of vaccination as considered by physicians, being a medical doctor, and participation in the pilot program.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

The use of botanical extracts of the plant Jatropha curcas (Euphorbiaceae) represents a valuable alternative to control insect pests and avoid the detrimental effects on the environment and health that arise due to synthetic chemical insecticides. Thus, we conducted a systematic review to summarize the published evidence on the bioactivity of J. curcas against insect pests. Electronic databases were searched to identify studies that assessed J. curcas extracts against insect pests in various types of crops. We included 39 articles that reported the insecticidal and insectistatic activity of several botanical extracts from J. curcas against insects of eight different taxonomic orders. The evidence demonstrates that aqueous and methanolic extracts from seeds and leaves, seed oil, and petroleum ether seed extracts were effective against insect pests of stored grains, aphids of cabbage, sorghum, fruit flies, and desert locusts. The extracts caused high mortality, controlled the populations, reduced oviposition, diminished hatchability, and increased the antifeedant effect. However, the type of solvent used to obtain the botanical extract and the method of application (contact or food) are fundamental to increase its bioactivity. Therefore, botanical extracts from seeds and leaves of J. curcas should be considered as an alternative against insect pests and may be incorporated into integrative and sustainable management for insect control.

Innovative tissue engineering biomimetic hydrogels based on hydrophilic polymers have been investigated for their physical and mechanical properties. 5% to 25% by volume loading PHEMA-nanosilica glassy hybrid samples were equilibrated at 37°C in aqueous physiological isotonic and hypotonic saline solutions (0.15 and 0.05 M NaCl) simulating two limiting possible compositions of physiological extracellular fluids. The glassy and hydrated hybrid materials were characterized both for dynamo-mechanical properties and equilibrium absorptions in the two physiological-like aqueous solutions. Mechanical and the morphological modifications occurring in the samples have been described. The 5% volume nanosilica loading hybrid nanocomposite composition showed mechanical characteristics in the dry and hydrated states that were comparable to those of cortical bone and articular cartilage, respectively, and then chosen for further sorption kinetics characterization. Sorption and swelling kinetics were monitored up to equilibrium. Changes in water activities and osmotic pressures in the water-hybrid systems equilibrated at the two limiting solute molarities of the physiological solutions have been related to the observed anomalous sorption modes using the Flory-Huggins interaction parameter approach. The bulk modulus of the dry and glassy PHEMA-5% nanosilica hybrid at 37°C has been observed to be comparable with the values of the osmotic pressures generated from the sorption of isotonic and hypotonic solutions. The anomalous sorption modes and swelling rates are coherent with the difference between osmotic swelling pressures and hybrid glassy nano-composite bulk modulus: the lower the differences the higher the swelling rate and equilibrium solution uptakes. Bone tissue engineering benefits of use of tuneable biomimetic scaffold biomaterials that can be “designed” to act as biocompatible and biomechanically active hybrid interfaces are discussed.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Supramolecular structures are of great interest due to their applicability in various scientific and industrial fields. These fields of scientific action include promising applications i biomedical areas, in sensing, and in conductive and electrical phases. The sensible definition of supramolecular molecules is being set by investigators, who, because of the different sensitivities of their methods and observational timescales, may have different views as to what constitute these supramolecular structures. Besides, diverse polymers can be found to offer unique avenues for multifunctional systems with properties in medicine industrial applications. Aspects of this review provide different conceptual strategies to address molecular design, properties, and potential applications of self-assembly materials and the use of metal coordination as a feasible and useful strategy for constructing complex supramolecular structures. In this order of appreciations and ideas order, it is that this review report involves classic topics such as hydrogels that range from their relationship with drug delivery systems, to metallo-supramolecular materials, through applications in ophthalmic systems, in applications that require adhesiveness and electrically conductive hydrogels. This review also addresses systems that are largely based on hydrogel chemistry and the enormous opportunities to design very specific structures for applications that demand enormous specificity.

In this work, the analytical Lagrange-Kirchhoff model for the deformation for a taiko plate silicon is proposed. Under the conditions of validity of the linear theory of thin plates, the model is in agreement with the experimental data.

Purpose: The aim of this article is to analyze the incidence of undiagnosed obstructive sleep apnea OSA in patients affected by dento-skeletal malformation. We also evaluated the patterns most affected by the condition and calculated the post surgical changes. Methods: We conducted a retrospective cohort study on 71 patients including 35 men and 36 women. Patients were evaluated with Polysomnography before surgery and at least 6 months after surgery to assess any improvement or worsening of the apnea hypopnea index AHI index. Regarding AHI evaluation criteria an AHI > 5 was considered indicative of OSA, 4 5, com-pared to 20.5% described in the Italian population. Conclusion: In patients who receive orthognathic surgery the presence of Obstructive Sleep Apnea is significantly higher than in the general population. When planning the surgical correction of a dentoskeletal malformation, the surgeon must aim not only to the aesthetics results, but also to a proper stomatognathic and respiratory function, this cannot be done without taking poly-somnography information into account.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

More than 20 years after the discovery of the first anelloviruses (AVs), they still remain a mysterious group of viruses. To date, there is no clear understanding of their impact on the host organism, although information is emerging about their participation in various pathologies. However, it is well known that AVs are an important component of the human virome. In the current study we assessed the abundance of AVs in viromes from four nasal and pharyngeal samples from children with respiratory symptoms using a metagenomic approach. It is worth noting that three patients had known respiratory viruses and one did not have any. Regarding AVs, they were detected in all samples, namely Torque teno mini virus (TTMV). The greatest abundance and diversity of AVs (Torque teno virus (TTV), TTMV and Torque teno midi virus (TTMDV)) were shown in a diseased patient with an absence of respiratory viruses, which may indicate the potential involvement of AVs in the maintenance of respiratory symptoms. An activated immune system to combat the main pathogens, against the background of which the number of AVs decreases, is discussed as a possible reason for the reduced diversity of anellome in other patients. We also compared the results of the metagenomic approach and qPCR for major respiratory viruses, which were in agreement. In addition, metagenomic sequencing made it possible to obtain additional data on viral genomes in order to establish their taxonomic identification and characterize individual viral profiles in patients from the Siberian part of Russia.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

Eysenhardtia platycarpa (Fabaceae) is a medicinal plant used in México and it lacks biotechnological studies for its use. The aim of this work was to establish a cell suspension cultures (CSC) of E. platycarpa, determine the phytochemical profile, and evaluate its antifungal activity. Friable callus and CSC were established with 2 mg/L 1-naphthaleneacetic acid plus 0.1 mg/L kinetin. The highest total phenolics of CSC was 15.6 mg GAE/g dry weight and the total flavonoids content ranged from 56.2 to 104.1 µg QE/g dry weight. CG‒MS analysis showed that the dichloromethane extracts of CSC, sapwood and heartwood have a high amount of hexadecanoic acid (22.3 ‒ 35.3 %) and steroids (13.5 ‒ 14.7%). Heartwood and sapwood defatted hexane extracts have the highest amount of stigmasterol (≈ 23.4%) and β-sitosterol (≈ 43%), and leaf extracts presented β-amyrin (16.3%). Methanolic leaves extracts showed mostly sugars and some polyols, mainly D-pinitol (74.3%). Dichloromethane and fatty hexane extracts of CSC exhibited the percentages inhibition higher for Sclerotium cepivorum with 71.5 and 62.0%, respectively. The maximum inhibition for Rhizoctonia solani was with fatty hexane extracts of the sapwood (51.4%). Our study suggest that CSC extracts could be used as a possible complementary alternative to synthetic fungicides.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

The SARS-CoV-2 polybasic furin cleavage site is still a missing link. Remarkably, the two arginine residues of this protease recognition site are encoded by the CGG codon, which is rare in Betacoronavirus. However, the arginine pair is common at viral furin cleavage sites, but are not CGG-CGG encoded. The question is: Is this genetic footprint unique to the SARS-CoV-2? To address the issue, using Perl scripts, here I dissect in detail the NCBI Virus database in order to report the arginine dimers of the Betacoronavirus proteins. The main result reveals that a group of Middle East respiratory syndrome-related coronavirus (MERS-CoV) (isolates: camel/Nigeria/NVx/2016, host: Camelus dromedarius) also have the CGG-CGG arginine pair in the spike protein polybasic furin cleavage region. In addition, CGG-CGG encoded arginine pairs were found in the orf1ab polyprotein from HKU9 and HKU14 Betacoronavirus, as well as, in the nucleocapsid phosphoprotein from few SARS-CoV-2 isolates. To quantify the probability of finding the arginine CGG-CGG codon pair in Betacoronavirus, the likelihood ratio (LR) and a Markov model were defined. In conclusion, it is highly unlikely to find this genetic marker in betacoronaviruses wildlife, but they are there. Collectively, results shed light on recombination as origin of the virus CGG-CGG arginine pair in the S1/S2 cleavage site.

Boron Neutron Capture Therapy (BNCT) is a promising binary disease-targeted therapy, as neutrons preferentially kill cells labeled with boron (¹⁰B), which makes it a precision medicine treatment modality that provides a therapeutic effect exclusively on patient-specific tumor spread. Contrary to what is usual in radiotherapy, BNCT proposes cell-tailored treatment planning rather than to the tumor mass. The success of BNCT depends mainly on the sufficient spatial biodistribution of ¹⁰B located around or within neoplastic cells to produce a high-dose gradient between the tumor and healthy tissue. However, it is not yet possible to precisely determine the concentration of ¹⁰B in a specific tissue in real-time using noninvasive methods. Critical issues remain to be resolved if BNCT is to become a valuable, minimally invasive, and efficient treatment. Moreover, functional imaging technologies such as PET can be applied to determine biological information that can be used for the combined-modality radiotherapy protocol for each specific patient. Anyway, not only imaging methods but also proteomics and gene expression methods will facilitate BNCT becoming a modality of personalized medicine. This work provides an overview of the fundamental principles, recent advances, and future directions of BNCT as cell-targeted cancer therapy for personalized radiation treatment.

Precise monitoring of individual crop growth and health status is crucial for precision agriculture practices. However, traditional manual inspection methods are time-consuming, labor-intensive, and often lack the spatial resolution required for detailed analysis. This research addresses the need for efficient and high-resolution crop monitoring by leveraging Unmanned Aerial Vehicle (UAV) imagery and advanced computational techniques. The primary objective was to develop a methodology for precise identification, extraction, and monitoring of individual corn crops throughout their growth cycle. This was achieved by integrating UAV-derived data with image processing, computational geometry, and machine learning techniques. UAV imagery was ac-quired bi-weekly at altitudes of 40m and 70m, capturing the entire growth cycle of a corn crop from planting to harvest. A time-series Canopy Height Model (CHM) was generated by analyzing the differences between the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) derived from the UAV data. Local spatial analysis and image processing techniques were em-ployed to determine the local maximum height of each crop. Subsequently, a Voronoi data model was developed to delineate individual crop canopies, successfully identifying 13,000 out of 13,050 corn crops in the study area. For enhanced accuracy in canopy size delineation, vegetation indices were incorporated into the Voronoi model segmentation, refining the initial canopy area esti-mates by eliminating interference from soil and shadows. The proposed methodology enables precise estimation and monitoring of crop canopy size, height, biomass reduction, lodging, and stunted growth over time, providing valuable insights for precision agriculture practices. This work contributes to the scientific community by demonstrating the potential of integrating UAV technology, computational geometry, and machine learning for accurate and efficient crop mon-itoring at the individual plant level.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Tuberculosis (TB) is an infectious disease declared a global emergency by the World Health Organization and continues as one of the world’s top ten causes of death. TB diagnosis is more critical in developing countries where demanded infrastructure for detection, and treatment complicates the efforts against the disease. These aspects related to limited resources are significant, especially in areas away from the main cities, with few mechanisms to make a timely diagnosis that contributes to successfully addressing the possible patients. Artificial intelligence has begun to be essential in providing additional strategies in the diagnosis processes for health professionals’ support. This paper uses natural language processing (NLP) and machine learning (ML) techniques to create models that can supply TB diagnosis when the needed infrastructure is unavailable. Two different sources were explored: text extracted from electronic medical records (EMR) and patient clinical data (CD). Four proposals using five different machine learning models were implemented. The first two models employed ML and each data source independently. Then, two additional approaches developed a data fusion from both sources. This strategy’s employment was analyzed with physicians according to their pertinence in the process and understanding of the EMR. Finally, the results of the data fusion were compared to each source, obtaining better performance at using only the CD, where an area under the ROC curve of 69.9±2.3% was obtained. However, the advantage of analyzing physician’s reports is the availability of this information contrasted to clinical-specific data, which can be more useful in places far from the main cities without enough basic structure for its obtaining.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

This work analyzes the visibility and scientific impact of publications related to agricultural value chains. The incidence of bibliometric indicators allows for the interpretation of bibliographic information generated worldwide. Objective: The objective of this research is to analyze the published literature and bibliometric indicators on agricultural value chains. The Web of Science database was used to extract value chains data. The study analyzed articles published between 2010 and 2020. The keywords used are "agricultural value chains'' and articles from journals or studies related to the subject were selected for bibliometric analysis and methodological review. In the search for the keyword, a total of 4208 results were extracted, of which 1,669 records were considered for analysis. The bibliometric analysis of the data reveals that Wageningen University (55) has the highest number of publications, followed by Chinese Acad Sci (26). The author Klerkx L (9) has the highest number of records, followed by Hellin J (7). With respect to the countries with the greatest contributions on the subject are: the People's Republic of China, Germany, Italy, France and the United States. The study contributes to the analysis of bibliometrics and provides a methodological review of published journal articles on agricultural value chains. This bibliographic study presents the history of research development in agricultural value chains.

“De-[Constructing] Growth” is offered as a deeper and more useful conceptualization that avoids the negative connotations of, and resistance to, “degrowth” by decoupling profit from unsustainable consumption, production, and inequality.

This study aimed to investigate the atherogenicity (quality) of LDL particles in patients with acute and recovered from COVID-19 infection. The participants were adults, aged 18 years or older of both sexes. Those with positive RT-PCR results at baseline were included in the Acute COVID-19 group (n=33), and those with negative RT-PCR six months after acute infection, were included in the Recovered COVID-19 group (n=30). The LDL quality was evaluated using three validated methods: Z-scan, UV-visible spectroscopy, and Lipoprint. The Recovered COVID-19 group showed significantly higher numbers of large LDL particles (less atherogenic) than the Acute COVID-19 group (P&lt;0.05). We also found that COVID-19 infection was associated with the oxidative modification of LDL particles. D-dimer and CRP levels were correlated with Z-scan results and antioxidant-amount estimate. Moreover, we noticed that the infection left a sequel in LDL quality, even after six months of recovery. These findings highlight the importance of monitoring lipids during and after recovery from COVID-19 infection, and their potential deleterious effect on the LDL profile might correlate with the progression of atherosclerosis and poor clinical outcomes.