Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Natural fibers are being increasingly used in different areas of engineering, including as composite reinforcement. Among these fibers, carauá stands out for its good mechanical properties and adherence to resin. Nevertheless, little is known about the behavior of this material in the manufacture of a composite or whether classic failure theory can be used in this case. In this context, the present study assesses the mechanical properties of two laminas made of unidirectional curauá fiber with volumetric fiber percentages of 30 % and 22 %, and compares the results with the values obtained for four failure criteria reported in the literature, using analysis of variance (ANOVA). To that end, tensile tests were conducted in the direction of the fiber and at other loading angles, in addition to iosipescu shear tests. The results show that the maximum stress criterion does not represent the failure behavior of these materials and that the best was the Hashin criterion.

Techniques and tools meant to aid fire management activities in the Cerrado, such as accurately determining fuel load and composition spatially and temporally, are pretty scarce. The need to have fuel information for more efficient management in a considerably heterogeneous, biodiverse, and fire-dependent environment makes a constant search for the improvement of the use of remote sensing techniques in determining fuel characteristics. This study presents the following objectives: (1) to assess the use of data from Landsat 8 OLI images to estimate the fine surface fuel load of the Cerrado during the dry season by adjusting multiple linear regression equations; (2) to estimate fuel load through Random Forest and k-Nearest Neighbor (k-NN) algorithms in comparison with re-gression analyses; and (3) to evaluate the importance of predictor variables from satellite images. Therefore, 64 sampling units were collected, and the pixel values associated with the field plots were extracted in a 3 x 3 pixel window surrounding the reference pixel. For the multiple linear regression analyses, the R² values ranged from 0.63 to 0.78, and the models fitted by the Random Forest al-gorithm ranged from 0.52 to 0.83, while those fitted by k-NN ranged from 0.30 to 0.68. Adopting the Random Forest algorithm resulted in improvements in the statistical metrics of evaluation of the fuel load estimates for Cerrado grassland relative to the multiple linear regression analyses.

In the present work, we evaluate the prediction capability of six Pedotransfer functions (PTFs), reported in the literature, for the saturated hydraulic conductivity estimations (Ks). We used a database with 900 measured samples obtained from the Irrigation District 023, in San Juan del Rio, Queretaro, Mexico. Additionally, six new PTFs were construct for Ks from clay percentage, bulk density and saturation water content data. The results show, for the evaluated models, that one model present an overestimation for Ks>0.5 cm h-1 values, three models have a underestimation for Ks>1.0 cm h-1 and two models have a good correlation (R2>0.98) but are necessary more than three parameters. Nevertheless, the last two models requires from three to four parameters in order to get the optimization. By other hand, the models proposed in this work have a similar correlation with a less number of parameters: the fit is seen to be much better than using the existing ones, achieving a correlation of R2 = 0.9822 with only one variable and a R2 = 0.9901 when we use two.

Leishmania spp. is the aetiologic agent of leishmaniasis, a disease endemic in several developing countries. The parasite expresses and secretes several virulence factors that subvert macrophage function and immune response. Extracellular vesicles (EVs) can carry molecules of the parasites that show immunomodulatory effects on macrophage activation and disease progression. In the present work, we detected a significantly higher expression of lpg3 and gp63 genes in Leishmania amazonensis promastigotes recovered after successive experimental infections (IVD-P) compared to those cultured for a long period (LT-P). In addition, we observed a significantly higher percentage of infection and internalized parasites in groups of macrophages infected with IVD-P. Macrophages previously treated with EVs from LT-P showed higher percentages of infection and production of inflammatory cytokines after challenge with the parasite compared to untreated ones. However, macrophages infected with parasites and treated with EVs did not reduce the parasite load. In addition, no synergistic effects were observed in infected macrophages treated with EVs and reference drugs. In conclusion, parasites cultured for a long period in vitro and recovered from animals’ infection differently affect the macrophage response. Furthermore, EVs produced by these parasites affected macrophage response in the early infection of these cells.

Cancer is a disease that encompasses multiple and different malignant conditions and is among the leading causes of death in the world. Therefore, the search for new pharmacotherapeutic options and potential candidates that can be used as treatments or adjuvants to control this disease is urgent. Natural products, especially those obtained from plants, have played an important role as a source of specialized metabolites with recognized pharmacological properties against cancer, therefore, they are an excellent alternative to be used. The objective of this research was to evaluate the action of the monoterpene isoespintanol (ISO) against the human tumor cell lines MDA-MB-231, A549, DU145, A2780, A2780-cis and the non-tumor line MRC-5. Experiments with MTT and fluorescence with propidium iodide (PI), DAPI and green plasma revealed the cytotoxicity of ISO against these cells; furthermore, morphological and chromogenic studies revealed the action of ISO on cell morphology and the inhibitory capacity on reproductive viability to form colonies in MDA-MB-231 cells. Likewise, 3D experiments validated the damage in these cells caused by this monoterpene. These results serve as a basis for progress in studies of the mechanisms of action of these compounds and the development of derivatives or synthetic analogues with a better antitumor profile.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

In order to meet the Millennium Development Goals set forth by the United Nations’ Millennium Summit that took place in 2000, in New York, particularly in the area of education, the Mozambican Government decided that, from 2003 onwards, during their primary school formation, students should be passed automatically even if they do not have enough intellectual capacities that justify their progress. In fact, this decision was made during a period when there were many pupils being failed, due to various reasons. After more than 15 years of its implementation, this paper aims to analyzing the results acquired from this decision, from the point of view of the quality of education. This will be done taking into account the prevailing situation of education in Mozambique. Having considered these aspects, the paper will move on to presenting some of the challenges and opportunities that the country should consider in the area of education, as a way to bring about better outcomes and promote development, in the country.

Cantharidin, a toxic monoterpene secreted by blister beetles, has long been used in traditional Chinese and modern medicine for its unique properties. However, despite its widespread use, its effects on fish have not been studied in depth. The aim of this study was to evaluate the potential therapeutic applications of cantharidin in fish by examining its antioxidant, hemoagglutinating, hemolytic and cytotoxic activities at different concentrations (0, 0.625, 1.25, 2.5, 5 and 10 μg mL-1) in three different cell lines. In addition, the study explored the bactericidal and bacteriostatic properties of cantharidin against various fish pathogenic bacteria. The results revealed that there were no significant differences in antioxidant, hemagglutinating or hemolytic activities between the different concentrations of cantharidin tested. However, the study found that cantharidin exhibited dose- and time-dependent cytotoxicity in sea bream (Sparus aurata) erythrocytes and in SAF-1, PLHC-1 and Hela cell lines, resulting in morphological changes indicative of apoptosis. Interestingly, the highest dose of cantharidin tested demonstrated potent bactericidal activity against four marine fish opportunistic bacteria, including Vibrio harveyi, V. anguillarum, Photobacterium damselae and Tenacibaculum maritimum, but no statistically significant changes in bacteriostatic activity were observed against any of the bacteria tested. Overall, these results provide valuable information on the potential therapeutic applications of cantharidin in fish aquaculture. Further research is needed to fully understand the mechanisms of action and to explore possible preventive uses of cantharidin in fish.

Cervical cancer is associated with persistent infections by high-risk HPV types that may have nucleotide polymorphisms and, consequently, different oncogenic potentials. Therefore, the objective of this study was to evaluate the genetic variability and structural effects of E7 oncogene of HPV58 in cervical scraping samples from Brazilian women. The study was carried out with patients from hospitals in metropolitan area of Recife, PE, Brazil. The most frequent HPV type was HPV16, 18 and 58, respectively. Phylogenetic analysis showed that the isolates were classified as sublineages A2, C1 and D2. Two positively selected mutations were found in E7: 63G and 64T. The mutations G41R, G63D and T64A in E7 protein were predicted to reduce the stability of the protein structure. Regarding the interaction of the E7 variant of HPV58 with the signaling of the NF-kB pathway, we observed that the variant HPV58/UFPE-54S decreased the activity of the pathway when compared to the prototype and the other variants behaved similarly to the prototype and the prototype increased the activity of the pathway when compared to pcDNA. In this study, it was possible to identify mutations that may interfere in the molecular interaction between the viral oncoproteins and host proteins.

In the realm of educational technology, Data Analytics (DA) is reshaping teaching and learning. This paper investigates the impact of DA on education, specifically comparing Student Information Systems (SIS) and Learning Management Systems (LMS). Data-driven insights from SIS and LMS platforms enable educators to tailor instructional strategies to individual student needs effectively. While SIS manages student data for administrative tasks, LMS offers tools for content delivery and collaboration. Using the strengths of SIS and LMS, educators can optimise teaching and learning experiences, tracking student progress, and fostering collaboration. The comparison emphasises their distinct roles: SIS manages administrative tasks, while LMS focusses on content delivery and collaboration. Using both systems, educators improve the teaching and learning experience, leveraging DA for continuous improvement. In summary, this paper underscores the transformative role of DA in education, framed within the context of comparing the SIS and LMS functionalities. By examining the intersection of data-driven decision making and educational technology, educators are equipped with the tools and knowledge to harness the power of data for meaningful and impactful teaching and learning.

This article describes the study and digital implementation of a system onboard a TMS 3208F28335 ® DSP for vector control of the bearing motor speed with 4 poles split winding with 250W of power. Smart techniques: ANFIS and Neural Networks were investigated and computationally implemented to evaluate the bearing motor performance under the following conditions: operating as an estimator of uncertain parameters and as a speed controller. Therefore, the MATLAB program and its toolbox were used for the simulations and the parameter adjustments involving the structure ANFIS (Adaptive-Network-Based Fuzzy Inference System) and simulations with the Neural Network. The simulated results showed a good performance for the two techniques applied differently: the estimator and a speed controller using both a model of the induction motor operating as a bearing motor. The experimental part for velocity vector control uses three control loops: current, radial position, and speed, where the configurations of the peripherals, that is, the interfaces or drivers for driving the bearing motor.

The endorsement from Christian circles in facilitating the rise of right-wing populism in Brazil, the United States, as well as the support and alliance of the Polish Catholic Church with the Law and Justice (PiS) government, is widely acknowledged. Embedded within the intricate fabric of multifaceted factors contributing to the surge of right-wing populism, the Culture War assumes a pivotal yet often underestimated role. Manifesting as a profound confrontation, the Culture War signifies an existential clash between contrasting perspectives concerning socio-cultural values grounded in religious scripture. Progressive endeavors strive to deconstruct longstanding norms, advocating for the ascendancy of post-materialistic ideals, while conservative domains portray an unwavering commitment to safeguarding national and religious socio-cultural values as sacrosanct. Both factions employ moral-ethical justifications in their respective pursuits, rendering the landscape of cultural discourse a nuanced tapestry of ideological contention. The influence of Christian doctrine on the conflict surrounding social justice, and the potential convergence between Christian doctrine and the positions of Populist right-wing movements on social justice issues, is underscored. By employing a singular case study focused on Portugal, owing to the nation's enduring relationship with Catholicism spanning from Monarchical times to the Republic and the Fascist Catholic regime, Portugal emerges as indisputably one of the most religious countries in the Western world, akin to Poland. Consequently, in theory, the support of the Portuguese Catholic Church for the nascent Populist right-wing and Christian-oriented party should be evident amidst the Culture War conflict, wherein conservative religious Christian values face existential challenge. However, the backing extended to CHEGA by both the Catholic Church and the Portuguese Episcopal Conference assumes an ambivalent and markedly diminished stance, diverging from the previously robust support observed in established center-right mainstream parties such as the PSD and CDS. Despite this reality and the absence of official support for CHEGA, numerous Christian politicians or activists have expressed endorsement or alignment with the right-wing party, departing from their former affiliations, primarily due to social justice concerns.

Background: Limited research has explored sex-specific differences in death predictors of HF pa-tients with ischemic (iCMP) and nonischemic (niCMP) cardiomyopathy. This study assessed sex differences in niCMP and iCMP prognosis. Methods: We studied 7,487 patients with HF between February 2017 and September 2020. Clini-cal features and echocardiographic findings were collected. We used Kaplan-Meier, Cox propor-tional hazards models, and score chi-square of Cox regression to determine death predictors in women and men. Results: mean age was 64.3±14.2 years, with 4,417 (59%) males. Women with iCMP and niCMP exhibited significantly higher mean age, higher mean left ventricular ejection fraction, and smaller left ventricular diastolic diameter than men. Over 2.26 years of follow-up, 325 (14.7%) women and 420 (15.7%) men, and 211 women (24.5%) and 519 men (29.8%) died in niCMP (p=NS) and iCMP (p=0.004), respectively. Cumulative incidence of death was higher in men with iCMP (log-rank p<0.0001) but similar in niCMP. Cox regression showed chronic kidney disease, dia-betes, stroke, atrial fibrillation, age, and myocardial infarction, as main predictors of death for iCMP in women and men. Conclusion: Women exhibited a better prognosis than men in iCMP, but similar for niCMP. Nevertheless, sex was not an independent predictor of death for both CMP.

Vitamin D (VD) is a pro-hormone essential for life in higher animals. It is present in few types of foods and is produced endogenously in the skin by a photochemical reaction. The final step of VD activation occurs in the kidneys involving a second hydroxylation reaction to generate the biologically active metabolite 1,25(OH)₂-VD. Extrarenal 1α-hydroxylation has also been described to have an important role in autocrine and paracrine signaling. Vitamin D deficiency (VDD) has been in the spotlight as a major public health-care issue with an estimated prevalence of more than a billion people worldwide. Among individuals with chronic kidney disease (CKD), VDD prevalence has been reported to be as high as 80%. Classically VD plays a pivotal role in calcium and phosphorus homeostasis. Nevertheless, there is a growing body of evidence supporting the importance of VD in many vital nonskeletal biological processes such as endothelial function, renin-angiotensin-aldosterone system modulation, redox balance and innate and adaptive immunity. In individuals with CKD, VDD has been associated with albuminuria, faster progression of kidney disease and increased all-cause mortality. Recent guidelines support VD supplementation in CKD based on extrapolation from cohorts conducted in the general population. In this review, we discuss new insights on the multifactorial pathophysiology of VDD in CKD as well as how it may negatively modulate different organs and systems. We also critically review the latest evidence and controversies of VD monitoring and supplementation in CKD patients.

Eysenhardtia platycarpa (Fabaceae) is a medicinal plant used in México and it lacks biotechnological studies for its use. The aim of this work was to establish a cell suspension cultures (CSC) of E. platycarpa, determine the phytochemical profile, and evaluate its antifungal activity. Friable callus and CSC were established with 2 mg/L 1-naphthaleneacetic acid plus 0.1 mg/L kinetin. The highest total phenolics of CSC was 15.6 mg GAE/g dry weight and the total flavonoids content ranged from 56.2 to 104.1 µg QE/g dry weight. CG‒MS analysis showed that the dichloromethane extracts of CSC, sapwood and heartwood have a high amount of hexadecanoic acid (22.3 ‒ 35.3 %) and steroids (13.5 ‒ 14.7%). Heartwood and sapwood defatted hexane extracts have the highest amount of stigmasterol (≈ 23.4%) and β-sitosterol (≈ 43%), and leaf extracts presented β-amyrin (16.3%). Methanolic leaves extracts showed mostly sugars and some polyols, mainly D-pinitol (74.3%). Dichloromethane and fatty hexane extracts of CSC exhibited the percentages inhibition higher for Sclerotium cepivorum with 71.5 and 62.0%, respectively. The maximum inhibition for Rhizoctonia solani was with fatty hexane extracts of the sapwood (51.4%). Our study suggest that CSC extracts could be used as a possible complementary alternative to synthetic fungicides.

This paper investigates the path following control problem for a unmanned surface vehicle (USV) in the presence of unknown disturbances and system uncertainties. The simulation study combines two different types of sliding mode surface based control approaches due to its precise tracking and robustness against disturbances and uncertainty. Firstly, an adaptive linear sliding mode surface algorithm is applied, to keep the yaw error within the desired boundaries and then an adaptive integral non-linear sliding mode surface is explored to keep an account of the sliding mode condition. Additionally, a method to reconfigure the input parameters in order to keep settling time, yaw rate restriction and desired precision within boundary conditions is presented. The main strengths of proposed approach is simplicity, robustness with respect to external disturbances and high adaptability to static and dynamics reference courses without the need of parameter reconfiguration.

The installation of electric vehicle supply equipment (EVSE) increases demand and peak loads, potentially straining existing energy distribution infrastructure. Dispersed and inadequately planned placement of charging points (CPs) can disrupt the electrical grid, surpass contracted demand thresholds, and require infrastructure upgrades, thereby incurring unfeasible costs for Distribution System Operators (DSOs). In this context, it is necessary to recognize the role of business models in enabling effective electrification of the transportation sector. In response to these challenges, this paper introduces a novel e-mobility hub management strategy, tailored for implementation in the Brazilian context. The proposed strategy revolves around a microgrid configuration encompassing dispatchable and photovoltaic generation, a battery energy storage system (BESS), EVSE infrastructure, and local loads. Moreover, this centralized controller facilitates the implementation of dynamic pricing and demand-response mechanisms, integral to business models seeking to integrate EVSE into the distribution grid. To validate the efficacy of the proposed solution, hardware-in-the-loop (HIL) simulations of the microgrid system are conducted. These simulations, incorporating the centralized controller, serve as a tool for assessing system performance and viability before on-site equipment deployment. Finally, this paper concludes with the insights gleaned from test analysis and its discussion through a selection of the most expressive scenarios, including islanded and connected operation modes.

This study aims to evaluate the land surface temperature (LST) and the thermal characteristics of the Urban Canopy Layer (UCL) of the urban canyon in Avenida Rio Branco in the Central Business District (CBD) of Rio de Janeiro during summer. In order to conduct this evaluation, two methods were employed: 1) TIRS Landsat-8 sensor for data selection and processing (latest generation, 2011-2020); ; 2) field survey using nine sampling points — seven along two mobile transects, one fixed point, and one vertical measurement point, which required the use of a RPA (Remotely Piloted Aircraft). Three categories of analysis were established for the field survey based on the prevailing synoptic situations: stability, instability, and post-instability. The CBD is characterized by extensive areas with surface heat islands, in which temperatures were higher than 38.9°C; the areas with milder LSTs were Campo do Santana, Avenida Rio Branco, and one of the Mixed-Use Zones (Praça Mauá). With respect to Rio Branco Avenue, the LST niches of lowest elevation were derived through building shadowing; however, the orbital data diverged from the observation data of the ten field-study days. In situ data revealed that the characteristics urban morphology of Avenida Rio Branco is susceptible to the formation of heat islands, presenting heat islands of very strong magnitude (over 6.1°C) in atmospheric stability, strong magnitude (4.1-6.0°C) in atmospheric instability, and moderate magnitude (2.1°C-4.0°C) in post-atmospheric instability. Despite the synoptic situation, thermal cores were concentrated at 1 pm. The intersection between Avenida Rio Branco, Rua do Ouvidor, and Praça Mauá stored most of the solar energy received during the day due to the greater sky obstruction caused by the verticalization. Finally, vertical analysis demonstrated the formation of a thermal inversion on the night of the highest mean air temperature (29.5°C), probably, due to the roughness and number of buildings in the urban canyon.

The use of new assistive technologies in general, and Socially Assistive Robots (SAR) in particular is becoming increasingly common for supporting people’s health and well-being. However, it still faces many issues regarding long-term adherence, acceptability and utility. Most of these issues are due to design processes that insufficiently take into account the needs, preferences and values of intended users. Other issues are related to the currently very limited amount of long-term evaluations, performed in real world settings, for SAR. This study presents the results of two regional projects that consider as a starting hypothesis that the assessment in controlled environments and/or with short exposures may not be enough in the design of a SAR deployed in a retirement home and the necessity of designing for and with users. Thus, the proposed methodology has focused in use cases definitions that follow a human-centred and participatory design approach. The main goals have been facilitating system acceptance and attachment by involving stakeholders in the robots design and evaluation, overcoming usage barriers and considering user’s needs integration. The implementation of the first use case deployed and the two-phase pilot test performed in the retirement home are presented. In particular, a detailed description of the interface re-design process based on improving a basic prototype with users’ feedback and recommendations is presented together with main results of a formal evaluation that has highlighted the impact of changes and improvements addressed in the first redesign loop of the system.

Sporotrichosis is a subcutaneous mycosis affecting humans and other animals that can be transmitted a zoonosis with cats as the main vector. The conventional anti-fungal therapy is especially inefficient in immunocompromised patients, who tend to develop the most severe forms of the disease, thus prompting the search for alternative therapies. Given their antigen-presenting properties, dendritic cells (DCs) have been used in both prophylactic and therapeutic vaccination strategies. Hence, this study aims to assess the use of DCs as a prophylactic tool in sporotrichosis by evaluating the immune profile induced by Sporothrix schenckii cell wall proteins (SsCWP)-stimulated bone-marrow-derived DCs (BMDCs). Mouse BMDCs were stimulated with SsCWP for 24 hours and analyzed for the surface expression of co-stimulatory molecules and TLR-4, as well as the secretion of proinflammatory cytokines and IL-10. Following that, activated BMDCs were cocultured with splenocytes for 72 hours and had the same cytokines measured in the supernatant. SsCWP-stimulated BMDCs showed higher expression of CD80, CD86, and CD40, but not TLR-4, and higher secretion of IL-6, IL-17A, and TNF. On the other hand, higher levels of IFN-γ, IL-10, and IL-2 were found in the supernatants of the coculture as compared with the BMDCs alone; TNF secretion was almost completely abrogated, whereas IL-6 was only partially inhibited and IL-17A was unaffected. Our results thus suggest SsCWP-stimulated BMDCs are able to induce a Th1-prone cytokine profile, known to be protective against other fungal diseases. This result could lead to evaluate the development of prophylactic and/or therapeutic DC-based tools against sporotrichosis.

This paper shows the proposal of the use of linked data for smart metering systems. The aim of linked data in smart grid applications such as smart metering systems is to give semantic knowledge of the energy transactions between all participators in the power markets. In combination with other technologies like blockchain, the linked data could improve decentralization and security in the world's energetic future.

This paper introduces the implementation of a genetic programming (GP)-based procedure to the automatic design and tuning of process controllers. The proposed approach makes a significant contribution to the field of artificial intelligence (AI) in control engineering. Unlike other controller design methods, the GP-based program handles the entire design in the time domain, including differential operations like derivatives and integrals, without the need for intermediate inverse Laplace transformation. This approach not only simplifies the design process but also ensures that all generated controllers are implementable in physical systems. Furthermore, GP’s functions set includes various mathematical operations beyond basic arithmetic operators, such as trigonometric, exponential, and logarithmic operators. The performance and validity of the resulting controllers generated by the proposed GP-based approach are evaluated by verifying whether the generator can replicate the structure and performance of those produced by traditional controller design methods and, in some cases, achieve even better results. As a result, the GP-based approach presents a promising solution for automating the controller design process and addressing control problems in various engineering applications.

Spike-and-wave discharge (SWD) pattern detection in electroencephalography (EEG) signals is a key signal processing problem. It is particularly important for overcoming time-consuming, difficult, and error-prone manual analysis of long-term EEG recordings. This paper presents a new SWD method with a low computational complexity that can be easily trained with data from standard medical protocols. Precisely, EEG signals are divided into time segments for which the Morlet 1-D decomposition is applied. The generalized Gaussian distribution (GGD) statistical model is fitted to the resulting wavelet coefficients. A k-nearest neighbors (k-NN) self-supervised classifier is trained using the GGD parameters to detect the spike-and-wave pattern. Experiments were conducted using 106 spike-and-wave signals and 106 non-spike-and-wave signals for training and another 96 annotated EEG segments from six human subjects for testing. The proposed SWD classification methodology achieved 95 % sensitivity (True positive rate), 87% specificity (True Negative Rate), and 92% accuracy. These results set the path to new research to study causes underlying the so-called absence epilepsy in long-term EEG recordings.

Background: It is very important that nurses receive adequate training in Sexual and Reproductive Health (SRH). In this study, the contents of the SRH subject in the undergraduate nursing curricula of 77 Spanish universities were examined in order to determine what SRH training nursing students are receiving. Methods: The contents of the SRH subject of all the curricula that were available online were reviewed. The distribution of the contents (topics) in the two areas (reproductive health and sexual health) was analyzed, and the prevalence of each topic was established. It was also determined whether there were differences in topics between public (n=52) and private universities (n=25). Results: The training of nursing students focuses mainly on the area of Reproductive Health (15 topics). Most of the topics of this area had a prevalence greater than 50%. Although the area of Sexual Health had 14 topics, most of these topics had a low prevalence (&lt;20%), especially in private universities. Conclusions: It was found that there is considerable variation in the distribution and prevalence of SRH topics between universities. The contents of the area of Reproductive Health are usually prevalent in most of the curricula, however the contents of the area of Sexual Health are very limited in most of the universities. An organizational effort is required to determine and standardize the contents of SRH that nursing students should receive in Spain to avoid inequalities in their training.

Wrist shape varies greatly across primates and previous studies indicate that the numerous morphological differences among them are related to a complex mixture of phylogeny and function. However, little is known about whether the variation in these various anatomical differences is linked and to what extent the wrist bones vary independently. Here, we used 3D geometric morphometrics on a sample of extant hominids (Homo sapiens, Pan troglodytes, Gorilla gorilla, and Gorilla beringei), to find the model that best describes the covariation patterns among four of the eight carpals (i.e., capitate, lunate, scaphoid, and trapezium). For this purpose, 15 modular hypotheses were tested using the Covariation Coefficient. Results indicate that there is a covariation structure common to all hominids, which corresponds to stronger covariation within each carpal as compared to the covariation between carpals. However, the results also indicate that that there is a degree of codependence in the variation of some carpals, which is unique in humans, chimpanzees, and gorillas, respectively. In humans there is evidence of associated shape changes between the lunate and capitate, and between the scaphoid and trapezium. This covariation between lunate and capitate is also apparent in gorillas, while chimpanzees display the greatest disassociation among carpals, showing low covariation values in all pairwise comparisons. Our analyses indicate that carpals have an important level of variational independence which might suggest a high degree of independent evolvability in the wrists of hominids, and that although weak, the structure of associated changes of these four carpals varies across genera. To our knowledge this is the first report on the patterns of modularity between these four wrist bones in the Homininae and future studies might attempt to investigate whether the anatomical shape associations among carpals are functionally related to locomotion and manipulation.

Tourism, and particularly residential tourism, has led to a change in the urban and demographic model of towns along the European Mediterranean coastline. Water as a limited and limiting resource for the growth of tourism is a popular topic in the scientific literature. However, the incorporation of non-conventional resources (desalination) has meant, in theory, that this limitation has been overcome. The aims of this paper are: a) to identify the different tourism models implanted in this territory and describe them from the point of view of their consumption of water in the demand cycle from 2002 to 2017; b) analyse the hydrosocial cycle, highlighting the measures aimed at satisfying water demand; and c) identify the limitations associated with these hydrosocial systems. To this end, different types of information will be processed, and various complex indicators produced. The results show the importance that demand management and the use of desalinated water in increasing the resilience of this territory to aridity. However, this has generated other problems associated with a tsunami of construction and the continuity of a non-sustainable territorial model.

PEM fuel cell is a technology successfully used in the production of energy from hydrogen, allowing the use of hydrogen as an energy vector. It is scalable for stationary and mobile applications. However, the technology demands more research. An important research topic is fault diagnosis and condition monitoring to improve the life and the efficiency and to reduce the operation costs of PEMFC devices. Consequently, there is a need of physical models that let deep analysis. These models must be accurate enough to represent the PEMFC behavior and to allow the identification of different internal signals of a PEM fuel cell. This work presents a PEM fuel cell model that uses the output temperature in a closed loop, so it can represent the thermal and the electrical behavior. The model is used to represent a NEXA Ballard 1.2 kW; therefore it is necessary to fit the coefficients to represent the real behavior. Five optimization algorithms were tested to fit the model, three of them were taken from literature and two were proposed. Finally, the model with the parameters identified was validated with real.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

3D bioprinting, like 3D printing, is a process that builds structures by depositing material layer by layer. In the specific case of bioprinting, these layers are composed of a biocompatible material together with living cells, allowing the creation of three-dimensional structures that recreate functional tissues and organs. Bioprinting cell-laden structures is complicated by the high rate of cell damage and stress that occurs during the process, caused by the high pressures and stresses to which they are subjected. To minimise damage during the process, it is important to study and optimise certain bioprinting conditions beforehand and to analyse how they affect the cells by means of computational simulations. In this review, both quantitative and qualitative data are collected to improve the nozzle geometry through computational simulation studies. Optimal ranges for nozzle diameter (0.2-1mm) and length (8-10mm; 300-900μm) have been defined, and recommendations for improving nozzle performance during bioprinting, such as the provision of an inner angle of 20-30°, an inner EDTA coating and a shear stress of less than 10kPa, have been gathered. Finally, based on the data collected, a design of experiments is proposed to obtain an optimal bioprinting configuration for a particular bioink.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

The vegetation in constructed wetlands (CWs) plays an important role in wastewater treatment. Popularly, the common emergent plants in CWs have been vegetation of natural wetlands. However, there are ornamental flowering plants that have some physiological characteristics similar to the plants of natural wetlands that can stimulate the removal of pollutants in wastewater treatments; such importance in CWs is described here. A literature survey of 87 CWs from 21 countries showed that the four most commonly used flowering ornamental vegetation genera were Canna, Iris, Heliconia and Zantedeschia. In terms of geographical location, Canna spp. is commonly found in Asia, Zantedeschia spp. is frequent in Mexico (a country in North America), Iris is most commonly used in Asia, Europe and North America, and species of the Heliconia genus are commonly used in Asia and parts of the Americas (Mexico, Central and South America). This review also compares the use of ornamental plants versus natural wetland plants and systems without plants for removing pollutants (COD, BOD, nitrogen and phosphorous compounds). The removal efficiency was similar between flowering ornamental and natural wetland plants. However, pollutant removal was better when using ornamental plants than in unplanted CWs. The use of ornamental flowering plants in CWs is an excellent option, and efforts should be made to increase the adoption of these system types and use them in domiciliary, rural and urban areas.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

This work deals with the evaluation of adhesive single-lap joints using ultrasonic guided waves. An adhesive bonded lap joint can be modelled as a three-layer system made up of two adherents and an adhesive. The propagation of guided waves in the joint is developed from matrix formulations. The behavior of the different guided wave modes that propagate in the bonded region is characterized and it is found that their relative amplitudes can be estimated based on the properties of the incoming wave that propagates in the non-bonded region. It was verified that the excitation of these modes is ruled by the degree in which the shapes of both modes match each other. A 3D simulation of two aluminium bonded plates using 500 kHz ultrasonic transducers in a pitch and catch configuration was implemented using the Matlab k-Wave toolbox. Scattering effects due to some produced defects located in the bond line of the lap joints were simulated. Experimental setup with some artificial defects produced in the aluminum joints were used in order to compare with the simulated. Qualitative agreement was observed for the two approaches. The observed deviation can be due to the different characteristics of the experimental and simulated defects.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.

Abstract: Background: The periodization of physical exercise to optimize the objectives is common in competitive sports, however physical exercise programs for the older adults do not usu-ally present periodization in their programming, they are limited to carrying out similar sessions throughout the program. Methods:137 people over 60 years old performed a physical exercise program, 71 people participated in a multicomponent non-periodized program as the Control Group (CG) and 66 people participated in a program periodized in blocks as the Experimental Group (EG). The block periodization program was oriented to the development of strength, and was carried out in 86 sessions three times per week during a period of 8 months. Anthropometric assessments were made using: weight, height, BMI and electrical bioimpedance; and functional evaluations through standardized tests: SPPB, TUG, handgrip and two-minute stair test. Results: After the intervention, the EG presents significant improvements in the TUG, in the weight and in the BMI. On the other hand, the CG presents significant improvements in fat weight, in BMI and in the 2-minute stair test. The SPPB did not present changes after the intervention. Conclusion: The periodization of physical exercise for older adults does not have a significant impact on the functional capacity in this population group.

This paper constitutes a first advance in the paleoenvironmental study of a small group of peatland ecosystems, of reduced size, located in the interior of the Iberian Peninsula (Puebla de Don Rodrigo, Ciudad Real, Spain). It represents a singular enclave, because these ecosystems are home to the southern-most peatlands in Europe, located at the lowest altitude in Spain, and are unique to the region of Castilla-La Mancha. They form ecosystems similar to the peat bogs of northern Europe, but in a Mediterranean climate. The analysis is followed of sample collection and data collection from documentary, textual, and cartographic sources drawn up since the 16th century up until the present day. The scientific analyses that were performed and the documentation that was consulted point to the hypothesis that these peatlands are the result of a long process of historical modification of the landscape in which anthropogenic activity has played a leading role, triggering a series of processes on the hillslopes that are culminating in the exhumation of the waterlogged areas, thereby establishing a recent genesis of these ecosystems.

Background: Aging impacts semantic abilities, therefore semantic exercises might be a valuable tool for cognitive stimulation in healthy older adults. However, programs in this area are limited. Methods: In the current paper, we adapted the BOX linguistic semantic program for online use via the CerUp platform. Our goal was to prepare the optimization future experience of CerUp users, including potential changes in task structure, level of difficulty and instructions, and participants’ adherence, engagement, performance accuracy, perceived difficulty, and adequacy ratings assigned to the instructions we provided that might guide future changes. Additionally, we created a map of hypothesized task-specific features that may guide tailor-made uses of the program. Results: To that end, we present preliminary results on the usability of CerUp. By analyzing task-specific usability data alongside the hypothesized map of task-specific features, we also tested the validity of the latter. Conclusions: These preliminary results on the usability of the CerUp platform highlight the potential of programs for semantic stimulation. Such findings can inform future optimizations of the program, tailored to users’ needs and effectively supporting overall language skills and general cognition.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

The present study aimed to evaluate the technical feasibility of using a calcined aggregate with mining residue in different pavement layers, including base, sub-base, and wearing course. For this purpose, the physical characterization of the residue and clay was performed, as well as the production of calcined aggregates at temperatures ranging from 800ºC to 1100ºC. Additionally, the suitability of these aggregates in pavement layers was assessed, considering the current standards. The physical results characterization indicated that the studied clay is suitable for manufacturing calcined clay aggregates since the particle size distribution showed ceramic potential - according to the Winkler diagram - and presented a plasticity index (PI) higher than 15%. In the tests of boiling-induced mass loss and unit mass, the values obtained were within the limits established by the standards, being lower than 10% and 0.88 g/cm3, respectively. Regarding the abrasion loss test, the M1100 aggregate showed "Los Angeles" abrasion values lower than the limit established by the standard, demonstrating its potential as an artificial aggregate in pavement applications.

Starting 1994, the debate for regulating organic agriculture in Brazil was officially recognized in May 1999. Still, only in 2003, when the law # 10,831 was instituted, the country reached an effective milestone on organic production, both internally and externally. Since the industry regulation, the legislation underwent many modifications, constantly reviewing and adjusting. The current study examined the institutionalization of organic production in Brazil and what the current regulations can be used as a reference for those interested in this sector. The most recent update of Organic legislation and its implication on practice were also discussed. A case study on production of strawberry in organic system is presented and discussed.

Forty-five male Dorper crossbred lambs (40.17 ± 0.35 kg BW) were used in order to investigate the effects of the duration of calcium propionate (CaPr) supplementation in lambs finished with zilpaterol hydrochloride (ZH) on the productive performance, carcass characteristics, and meat quality. Lambs were individually housed and fed a finishing-diet for 42 d before being slaughtered. Lambs received the following treatments: 1) No additives (CTL), 2) ZH supplementation for 28 d (with 3 d ZH withdrawal before slaughter) at a dosage of at 7.2 mg/kg diet (ZH), for treatments 3, 4, and 5, lambs received ZH and 10g CaPr/lamb/d throughout the entire phase (42 d), or during the last 28 or 14 d before slaughter. Compared to CTL, ZH lambs exhibited a similar average daily gain (ADG) but had lower dry matter intake (DMI), leading to increased feed efficiency. Supplementing with ZH alone did not affect carcass traits, visceral mass, whole cuts, or meat quality. Lambs that received both CaPr and ZH exhibited quadratic increases (p &lt; 0.05) in final BW (FBW), ADG, and dressing percentage (D%). These increases were optimal at an estimated inclusion durations of 26 d for FBW, 30 for ADG, and 39 d for D%. The ADG:DMI ratio and the longissimus muscle area (LMA) both exhibited quadratic increases (p &lt; 0.05). The optimal duration of CaPr supplementation for ADG:DMI ratio was found to be 28 d, while for LMA, it was 14 d. As the period of CaPr supplementation increased, there was a linear increase (p &lt;0.05) in hot carcass weight, leg circumference, and whole cuts of breast IMPS209 and shoulder IMPS207. Cook loss percent increased quadratically (p &lt; 0.05), being higher when CaPr was included for an estimated duration of 26 d. As the duration of CaPr supplementation increased, the purge loss percentage (PLR) also increased linearly (p &lt; 0.05). In conclusion, including CaPr in the diet for a duration of 28 d in lambs improved the response to ZH supplementation on the productive performance, carcass weight and some whole cuts. However, it can also have a negative effect on PRL%.

A novel gas-phase electrocatalytic system based on a low-temperature proton exchange membrane (Sterion) was developed for the gas phase electrocatalytic conversion of CO2 to liquid fuels. This system achieved gas-phase electrocatalytic reduction of CO2 at low temperatures (below 90 ºC) over a Cu cathode by using water electrolysis-derived protons generated in-situ on an IrO2 anode. Three Cu-based cathodes with varying metal particle sizes were prepared by supporting this metal on an activated carbon at three loadings (50, 20, and 10 wt%; 50%Cu-AC, 20%Cu-AC, and 10%Cu-AC, respectively). The cathodes were characterized by N2 adsorption–desorption, temperature-programmed reduction (TPR), and X-ray diffraction (XRD) whereas their performance towards the electrocatalytic conversion of CO2 was subsequently studied. The membrane electrode assembly (MEA) containing the cathode with the largest Cu particle size (50%Cu-AC, 40 nm) showed the highest CO2 electrocatalytic activity per mole of Cu, with methyl formate being the main product. This higher electrocatalytic activity was attributed to the lower Cu–CO bonding strength over large Cu particles. Different product distributions were obtained over 20%Cu-AC and 10%Cu-AC, with acetaldehyde and methanol being the main reaction products, respectively. The CO2 consumption rate increased with the applied current and the reaction temperature.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Objective: To identify risk factors(RF) related to abnormal glucose regulation(AGR) 3 years postpartum according to 3-month-postpartum glucose status. Research design: Normoglycemic pregnant women of the St. Carlos Gestational Study included before gestational week 12, during 2015-2017. Of 3,036 eligible women, 2529 were followed-up until delivery: 1400 participated in postpartum follow-up. AGR defined as fasting serum glucose (FSG)>5.6 mmol/L and/or HbA1c >5.7% (39 mmol/mol) and/or 2h-SG ≥140/mg/dL after 75-g OGTT. 12-modifiable and 3-unmodifiable RF were analyzed for associations with glycemic changes. Reinforcement of Mediterranean Diet adherence was provided to all women at the postpartum visit by a dietitian Results: 137/1400(9.8%) women presented AGR 3 years postpartum, 27/137(19.7%) also had at 3 months, whereas 110/137(80.2%) had not. The remaining 1,263(90.2%) women were normoglycemic 3 years postpartum, 1180/1263(84.3%) were at 3 months, while 83/1263(6.08%) had AGR and became normoglycemic. Women with GDM were more likely to progress to AGR 3 years postpartum (OR:1.60[1.33-1.92]) and less likely to remain normoglycemic (OR:0.22[0.15-0.33]) versus non-GDM women. Having >2/3 unmodifiable RF was associated with a reduced rate of maintained normoglycemia (OR:0.56[0.39-0.80]) and an increased risk of progression to AGR (OR:1.90[1.28-2.83]). Having >5/12 modifiable RF was associated with a reduced rate of maintained normoglycemic (OR:0.74[0.51-0.99]) and reversion of AGR (OR:0.49[0.25-0.97]), an increased progression to AGR (OR:1.40[1.00-2.09]), and persistence of AGR (OR:2.57[1.05-6.31]). Pre-gestational BMI≥25kg/m2 (OR:1.80[1.19-2.71]), post-delivery weight gain (OR:2.22[1.10-4.48]), and waist circumference >89.5cm (OR:0.54[0.36-0.79]), (all p<0.05) were the main modifiable RF. Conclusions: RF related to an increased probability for 3-year-postpartum AGR despite 3-month normoglycemia were identified, potentially useful when designing personalized strategies for pregnant women, directed towards minimizing unfavorable outcomes.

The real estate market is exposed to many fluctuations in prices, because of existing correlations with many variables, some of which cannot be controlled or might even be unknown. Housing prices can increase rapidly (or in some cases, also drop very fast), yet the numerous listings available online where houses are sold or rented are not likely to be updated that often. In some cases, individuals interested in selling a house (or apartment) might include it in some online listing, and forget about updating the price. In other cases, some individuals might be interested in deliberately setting a price below the market price in order to sell the home faster, for various reasons. In this paper we aim at developing a machine learning application that identifies opportunities in the real estate market in real time, i.e., houses that are listed with a price substantially below the market price. This program can be useful for investors interested in the housing market. We have focused in a use case considering real estate assets located in the Salamanca district in Madrid (Spain) and listed in the most relevant Spanish online site for home sales and rentals. The application is formally implemented as a regression problem, that tries to estimate the market price of a house given features retrieved from public online listings. For building this application, we have performed a feature engineering stage in order to discover relevant features that allows attaining a high predictive performance. Several machine learning algorithms have been tested, including regression trees, $k$-nearest neighbors, support vector machines and neural networks, identifying advantages and handicaps of each of them.

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

Background: Schizophrenia is a mental disorder associated with inflammatory and oxidative stress markers such as lactate; in addition, the rate of physical inactivity in this population is very high, which leads to physical and metabolic alterations. Aims: This study measured the effect of assisted physical exercise over lactate levels in schizophrenia. Methods: Stable outpatients with schizophrenia and a group of Healthy controls received two different programs of Physical exercise (Aerobic and Functional) in a clinical trial. Results: Patients had higher lactate compared to healthy controls before and after intervention, and had higher rate of lactate increase after activity. The finding of increased lactate in schizophrenia detected before and after physical exercise deserve further attention in biomarker studies and in the development of physical rehabilitation in schizophrenia, suggesting different profile of oxidative metabolism after physical exercise. Basal increased lactate may reflect mitochondrial dysfunction or metabolic dysregulation, and the higher rate of increase may reflect a different metabolic and oxidative process. Conclusion: The finding is in line with recent studies as surrogate of mitochondrial dysfunction in schizophrenia and points to the need of additional studies on mitochondrial activity in schizophrenia, and to additional care in the design of physical interventions in schizophrenia.

Amplitude growth rates of monochromatic gravity waves were estimated and compared from multiple instrument measurements carried out in Brazil. Wave dynamic parameters were obtained from sodium density profiles from lidar observations carried out in Sao Jose dos Campos (23°S, 46°W), while all-sky images of multiple airglow layers provided amplitudes and parameters of waves over Cachoeira Paulista (23°S, 45°W). Growth rates of gravity wave amplitudes from lidar and airglow imager data were consistent with dissipative wave behavior. Only a small amount of the observed wave events presented freely propagating behavior. Part of the observed waves presented saturated amplitude. The general saturated/damped behavior is consistent with diffusive filtering processes imposing limits to amplitude growth rates of the observed gravity waves.

Ozonated oil has several benefits for humans, as it contributes to numerous interventions, maintaining the quality of life and the well-being of individuals. Being a natural product, it has few or almost no side effects. Thus, the study aimed to verify the sensitivity and/or resistance of fixed o “Ozonated” and “Non-Ozonated” oils from Mauritia flexuosa (Buriti), Carapa guaianensis (Andiroba) and essential “Ozonated” oils from Menta piperita (Mint), Eugenia caryophyllus (Clove) in different concentrations, against internationally known bacteria from the American Type Culture Collection – ATCC, comparing with the “Non-Ozonated” versions of the respective oils, using the Agar diffusion technique. Thus, it is evident that the ozonation of the fixed oils of Buriti and Andiroba, as well as the essential oils of Mint and Clove, provided significant results, although they were statistically different. The Buriti and Andiroba oil were ineffective in inhibiting microorganisms. On the other hand, the essential oil of Mint and Clove obtained similar activity of inhibition of microorganisms. With regard to Ozonation, the Essential Oil of “Ozonated” Clove provided greater activity than the “Non-Ozonated” one, which inhibited only one tested microorganism, in addition to producing changes in its chemical composition, requiring individualized studies for the ozonation of each essential oil.

The decapod fauna in intertidal rocky shore in continental Chile has high species diversity mainly in northern and central Chile due high productivity of these coast due influence of cold Humboldt stream. One of the abundant species in these ecosystems is decapod Cyclograpsus cinereus Dana, 1851. The aim of the present study was determine the spatial distribution pattern of C. cinereus along rocky shore in Antofagasta bay, north of Chile between spring and summer 2018-2020. Data was obtained counting individuals from random quadrants in intertidal zones, to the obtained data was applied the variance mean ratio for determine if the specimens have random, aggregate or uniform distribution, that are associated to Poisson, negative binomial or positive binomial distributions respectively. Data obtained revealed the existence of associated distribution with respective negative binomial distribution pattern in 16 observations, and uniform distribution for 3 observations. The sites corresponds to rocky shores in urban zones, and in a protected zone, and the density does not have significant differences for both kind of sites. The observed data about aggregated pattern agree with observations for decapods for rocky shore in central and southern Chile, specifically in interpretative probabilistic models.

Antimicrobial resistance is one of the most important global health issues identified in recent decades. Different approaches have been used to establish the presence and abundance of antimicrobial resistance genes (ARGs) in the environment. In this study, we analyzed soil samples from Fildes Peninsula (King George Island, maritime Antarctica), exposed to different types of impact. The objective of the work was to identify ARGs in the samples, and evaluate if these genes were located in plasmids, using two different strategies. A metagenomic analysis was used to identify ARGs and if they were associated to plasmid sequences. The analysis showed that the site highly exposed to anthropogenic activity had a higher number of ARGs compared to other sites. A high percentage of those ARGs (19.4%), were located in plasmidic contigs. We also assessed replicon mobilization, using microbial communities from these soil samples as donors through an exogenous plasmid isolation method. In this case, we could recover plasmids with ARGs in a Tcr transconjugant clone. Although they could not be fully assembled, we could detect broad host range IncP1 and IncQ plasmid sequences. Our results indicate that sewage impacted soils could be a hotspot for ARGs spread into the Antarctic environment

Wireless Sensor Networks (WSNs) are being increasingly adopted in critical applications, where verifying the correct operation of sensor nodes is a major concern. Undesired events may undermine the mission of the WSNs. Hence their effects need to be properly assessed before deployment to obtain a good level of expected performance and during the operation in order to avoid dangerous unexpected results. In this paper we propose a methodology to support design and deployment of dependable WSNs by means of an event-based formal verification technique. The methodology includes a process to guide designers towards the realization of a dependable WSN and a tool ("ADVISES") to simplify its adoption. The tool allows to generate automatically formal specifications used to check correctness properties and evaluate dependability metrics at design time and at runtime. During the runtime we can check the behavior of theWSN accordingly to the results obtained at design time and we can detect sudden and unexpected failures, in order to trigger recovery procedures. The effectiveness of the methodology is shown in the context of two case studies, aiming to illustrate how the tool is helpful to drive design choices and to check the correctness properties of theWSN at runtime

Background: The effectiveness of the anti-COVID-19 vaccine remains a matter to be clarified. Methods: The humoral and cellular immunity after the administration of three doses of the Pfizer–BioNTech and Oxford AstraZeneca vaccines against SARS-CoV-2 over one year and the appearance of post-vaccination COVID-19 have been studied. Results: Anti-SARS-CoV-2 IgG and IgA antibodies showed a progressive increase throughout the vaccination period. This increase was greatest after the third dose. The highest levels were observed in subjects who had anti-SARS-CoV-2 antibodies prior to vaccination. There was an increase in CD4+ αβ, CD8+ γδ and TEM CD8+ γδ T cells, and a decrease in apoptosis in CD4+CD8+ and CD56+ αβ and γδ T cells. Post-vaccination SARS-CoV-2 infection was greater than 60%. The symptoms of COVID-19 were very mild and were related to γδ T cell deficit, specifically CD8+ TEMRA and CD56+ γδ TEM, as well as lower pre-vaccine apoptosis levels. Conclusions: Those results demonstrate the important role that γδ T cells play in SARS-CoV-2 vaccine immunization.

1960s Europe saw a large number of residential neighborhoods built to house those migrating from the countryside. Today, more than 50 years later, these neighborhoods suffer high levels of functional, social, and technical obsolescence. In response to this, University of Seville developed the Aura Strategy as an intervention methodology to find global solutions to issues in outdated neighborhoods. To provide visibility to this aspect of the Aura strategy, the retrofit proposal presented in this article provides a solution to improve the roofing of buildings in a case study neighborhood (Polígono de San Pablo, Seville) and an analysis of the results in terms of energy and financial savings for local residents. The results show that for a population of roughly 18,000 (in 2018), net savings, including energy and retrofitting costs, ranging from nearly 6.5 to over 8.6 million can be made over the 20-year life cycle span. Likewise, the results obtained on the reduction of thermal loads indicate a 72% decrease in energy consumption, equivalent to a saving of close to 4,500 tons of greenhouse gas emissions for the district and the entire life cycle time period, with the consequent benefits on the impact on air quality and and the fight against climate change. climate change.

Background: Selectively targeting dopamine receptors has been a persistent challenge in the last years for the development of new treatments to combat the large variety of diseases evolving these receptors. Although, several drugs have been successfully brought to market, the subtype-specific binding mode on a molecular basis has not been fully elucidated. Methods: Homology modeling and molecular dynamics were applied to construct robust conformational models of all dopamine receptor subtypes (D1-like and D2-like receptors). Fifteen structurally diverse ligands were docked to these models. Contacts at the binding pocket were fully described in order to reveal new structural findings responsible for DR sub-type specificity. Results: We showed that the number of conformations for a receptor:ligand complex was associated to unspecific interactions > 2.5 Å and hydrophobic contacts, while the decoys binding energy was influenced by specific electrostatic interactions. Known residues such as 3.32Asp, the serine microdomain and the aromatic microdomain were found interacting in a variety of modes (HB, SB, π-stacking). Purposed TM2-TM3-TM7 microdomain was found to form a hydrophobic network involving Orthosteric Binding Pocket (OBP) and Secondary Binding Pocket (SBP). T-stacking interactions revealed as especially relevant for some large ligands such as apomorphine, risperidone or aripiprazole. Conclusions: This in silico approach was successful in showing known receptor-ligand interactions as well as in determining unique combinations of interactions, key for the design of more specific ligands.

Heat pumps are increasingly becoming a key solution in the quest for decarbonization, offering a significant advantage over traditional boilers due to their superior energy efficiency. Not only can heat pumps provide both heating and cooling, but they also achieve thermal efficiencies exceeding 500%, which can seem to defy conventional expectations. The outdoor unit of a heat pump consists of about twenty main components, one of which is a complex network of copper pipes and sheets welded to valves, connectors, and other fittings. This set involves over thirty welded joints, highlighting a significant opportunity for reducing manufacturing time through process optimization. Copper is a critical material extensively used in various applications due to its excellent thermal and electrical conductivity. However, these very properties make welding copper particularly challenging, especially when aiming to automate and streamline industrial processes. Traditionally, connecting copper pipes and fittings is done through brazing, yet, alternative methods such as LASER welding, electron beam welding, resistance welding, friction welding, and ultrasonic welding also exist. This study focuses on the ultrasonic welding of copper, aiming to identify the optimal parameters that maximize the mechanical strength of overlapping joints and ensure effective tube sealing. Experimental results showed that for copper sheets, the best outcomes were achieved with a welding time of 3 s and a pressure of 6 bar. For tube sealing, the optimal conditions were a welding time of 3 s and a pressure of 4 bar. For both scenarios, the same variables were used, retention time of 0.62 s, initial pressure of 2 bar, retention pressure of 2 bar and sonotrode rising pressure of 3 bar. The analysis reveals that ultrasonic welding of copper can achieve both robust mechanical strength and reliable sealing, making it a promising technique for industrial applications.

In Mexico viticulture represents the second source of employment in the agricultural area after the fruit and vegetable sector. In developed countries, remote sensing is widely used for vineyard monitoring, however, this tool is barely used in developing countries of Iberoamerica. In this re-search, our overall objective is to characterize two vineyards in the state of Queretaro (Mexico) using Sentinel-2 and meteorological data, specifically spectral and thermal indices. Results showed that spectral indices obtained from Sentinel-2 bands have characterized adequately the phenolog-ical evolution of the different varieties of the vineyards. The Modified Soil-Adjusted Vegetation Index (MSAVI) was adequately used to discriminate the first stages of vineyards, while the Nor-malized Difference Vegetation Index (NDVI) was useful to monitor vineyards during the rest stages of vineyards. Thermal indices have shown that the best grape varieties were those that can adapt to both cooler and warmer temperatures, have a reasonable ripening period, and can produce wines with balanced acidity and flavors. In conclusion, the combination of meteorological (including thermal indices) and remote sensing data (NDVI and MSAVI) provide information for choosing the suitable grape variety for this region.

Individuals with Parkinson’s disease (PD) and freezing of gait (FOG) have a loss of presynaptic inhibition (PSI) during anticipatory postural adjustments (APAs) for step initiation. The mesencephalic locomotor region (MRL) has connections to the reticulospinal tract that mediates inhibitory interneurons responsible for modulating PSI and APAs. Here, we hypothesized that MLR activity during step initiation would explain the loss of PSI during APAs for step initiation in freezers. Thirty-four freezers were assessed in the ON-medication state. During a functional magnetic resonance imaging protocol of simulated APA task, we assessed beta of blood oxygenation level-dependent signal change of areas known to initiate and pace gait (e.g., MLR), in addition to PSI of the soleus muscle during APA for step initiation, and clinical (e.g., disease duration) and behavioral (e.g., FOG severity and APAs amplitude for step initiation) variables. A linear multiple regression model showed that MLR activity (R2=0.32, P=0.0006) and APA amplitude (R2=0.13, P=0.0097) explained together 45% of the loss of PSI during step initiation in freezers. Decreased MLR activity during a simulated APA task is related to a higher loss of PSI during APA for step initiation. Deficits in central and spinal inhibitions during APA may be related to FOG pathophysiology.

This paper presents new above-ground biomass (AGB) and biomass components equations for seventeen forest species in the temperate forests of northwestern Mexico. A data set corresponding to 1336 destructively sampled oak and pine trees was used to fit the models. Generalized method of moments was used to simultaneously fit systems of equations for biomass components and AGB, to ensure additivity. Additionally, the carbon content of each tree component was calculated by the dry combustion method, in a TOC analyser. The fitted equations accounted for on average 91, 83, 84 and 78% of the observed variance in stem wood and stem bark, branch and foliage biomass, respectively, whereas the total AGB equations explained on average 93% of the total observed variance in AGB. The inclusion of h or d²h as additional predictor in the d-only based equations systems slightly improved estimates of stem wood, stem bark and total above-ground biomass, and greatly improved the estimates produced by the branch and foliage biomass equations. The fitted equations were used to estimate AGB stocks at stand level from a database on growing stock from 429 permanent sampling plots. Three machine-learning techniques were used to model the estimated stand level AGB and carbon contents; the selected models were applied to map the AGB and carbon distributions in the study area, which yielded mean values of 129.84 Mg ha^-1 and 63.80 Mg ha^-1, respectively.

Mammalian fertilization initiates the reprogramming of oocytes and sperm, leading to the formation of a totipotent zygote. The zygotic genome remains transcriptionally silent throughout this intricate process, undergoing the maternal-to-zygotic transition (MZT) and subsequent zygotic genome activation (ZGA). Histone modifications are pivotal in shaping cellular identity and gene expression in many mammals. Recent advances in chromatin analysis enable a detailed exploration of histone modifications during ZGA. This review delves into conserved and unique regulatory strategies, providing essential insights into the dynamic changes in histone modifications and their variants during ZGA in mammals. The objective is to explore recent advancements in leading mechanisms related to histone modifications governing this embryonic development phase in depth. These considerations will be useful for informing future therapeutic approaches that target epigenetic regulation in diverse biological contexts, ranging from regenerative medicine to cancer research. It will also contribute to the extensive areas of evolutionary and developmental biology and possibly lay the foundation for future research and discussion on this seminal topic.

Diarrhoea is a serious cause of mortality worldwide that can lead to dehydration, gut barrier function impairment, nutrient malabsorption, and alterations of the gut microbiota (dysbiosis). Current solutions for its management, such as oral rehydration salts (ORS), inhibitors of the gut motility, antibiotics, and living probiotics only partially counteract the mechanisms of the disease and do not provide a full coverage of the problem. Potential risks of the use of living probiotic strains, particularly in immunocompromised patients, can be eliminated with the use of tyndallized (heat-killed) postbiotic bacteria and yeast. ABB C22® is a postbiotic combination of three tyndallized yeasts, namely Saccharomyces boulardii, Saccharomyces cerevisiae, and Kluyveromyces marxianus. To assess the action of the postbiotic combination on diarrhoea, immune and gut epithelial cell signaling assays, gut barrier formation assay and rotavirus gene expression assay were performed. ABB C22® showed a strong anti-inflammatory effect, an induction of the build-up of the gut epithelium, and a degree of protection against rotavirus infection. These experimental studies support the use of the postbiotic ABB C22® as a solution for the management of diarrhoea and gastrointestinal conditions, alone or in combination with existing but incomplete treatments.

Objective: To evaluate the direct costs of treating patients with neuromyelitis optica spectrum disorders (NMOSD) in outpatient care, from a hospital and Unified Health System (SUS) perspective. Methods: Observational study with data collection by microfunding, carried out with patients diagnosed with neuromyelitis optics, treated at a university hospital, in the city of Rio de Janeiro. Mann-Whitney tests were performed to measure cost differences between patient groups by disease severity and analysis perspective. Results: Nine individuals with a median age of 48 years (IQR 30 - 59 years) were included. The median total costs for patients with greater severity from the perspective of the SUS and the hospital were R$ 21,638.22 (IIQ: R$ 15,614.63; R$ 25,985.32) and R$ 32,094.11 (IIQ: R$ 25,610 .60; R$ 38,617.25) respectively. For patients with moderate severity the median was R$ 7,339.85 (IIQ: R$ 6,235.45; R$ 11,912.05) from the SUS perspective and R$ 11,505.80 (IIQ: R$ 7,339.85; R$ 22,424.76) from the perspective of the hospital, where the use of medications had a major impact. Conclusion: The main cost drivers were medicines, especially those used off-label, and procedures.

Obesity is a risk factor for the development of gestational diabetes mellitus (GDM). However, the most optimal type of nutritional intervention to prevent GDM in high-risk women is not clearly defined. This study investigates if nutritional treatment based on the Mediterranean diet (MedDiet) before 12th gestational week (GW) in women at high risk due to a body mass index (BMI)≥25kg/m2, reduces the rate of GDM and metabolic syndrome (MetS) at 3 years postpartum. We performed a post-hoc analysis of the San Carlos Gestational Prevention Study. A total of 735 women with BMI≥25kg/m2 were evaluated between 2015-2018, 246 in standard diet control group (CG) and 489 in MedDiet intervention group (IG). The rate of GDM was significantly lower in IG compared to CG (25.1%vs31.7%;p=0.037). Postnatal follow-up was completed by 141 women in CG (57%) and 312 women in IG (64%). At 3 years postpartum, we observed a reduction (relative risk 95% confidence interval) in the rates of impaired fasting glucose (IFG) (0.51 (0.28-0.92);p=0.019), obesity (0.51 (0.28-0.92),p=0.041), waist circumference (WC)≥89.5cm (0.54 (0.31-0.94);p=0.022) and MetS (0.56 (0.33-0.94);p=0.003). MedDiet reduces the rate of GDM and postpartum MetS in women with BMI)≥25kg/m2, suggesting that its implementation should be routinely recommended from the first GWs.

Mammary neoplasm affects a population of intact and elderly female dogs and 50% are malignant. In order to study this disease, cell culture is as a promising preclinical model, creating the opportunity to deposit cell lines at a cell bank, allowing a great reproducibility of the assays and making the validation of the results more reliable. Another important aspect is the possibility to establish models for better understanding tumour characteristics, such as vasculogenic mimicry. Due the importance of cancer cell lines in preclinical models, this study aimed to establish and characterize primary cell lines from canine mammary gland tumours according to immunophenotype and tumorigenicity, and with its ability to form vasculogenic mimicry-like structures in vitro and in vivo. Cell cultures were evaluated for morphology, phenotype, vasculogenic mimicry and tumorigenicity abilities. We collected 17 primary mammary carcinoma and 3 metastasis and had a satisfactory result in 10 of them. All cell lines presented spindle shape or polygonal morphology and expressed concomitant pan-cytokeratin and cytokeratin 8/18. Four cell lines had vasculogenic mimicry ability in vitro and two of them showed in vivo tumorigenic potential and forming VM in the xenotransplant tumour. Cell characterization of those lines will help to create a database for more knowledge of mammary carcinomas in dogs, including studies of tumour behaviour and new therapeutic targets.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

Circulating tumor cells (CTC) have shown to be prognostic in advanced colorectal cancer (advCRC), but their value for predicting response to treatment or as a source of molecular data is debated. We compared CellSearch® (Janssen Diagnostics, LLC) and IsoFlux^TM (Fluxion Biosciences Inc, South San Francisco, CA) systems for the enumeration of CTC in patients with newly diagnosed advCRC (group 1; n=34). Using castPCR^TM we studied KRAS status in CTC isolated with IsoFlux^TM and compared it with that of the primary tumor in patients from group 1 and in KRAS wild-type (KRAS^WT) patients with progressive disease (group 2; n=22). Median number of CTC detected with CellSearch® (groups 1 and 2) was 1 (range: 0-78) and with IsoFlux^TM (group 1) was 8 (range: 0-419), showing a modest correlation (r=0.345, P=0.036), which improved if lung metastases (r=0.805, P=0.016) or if lung and liver metastases were present (r=0.812, P=0.05). A Bland-Altman plot showed that the higher the number of CTC detected the larger the difference between both methods in favor of IsoFlux^TM. After a median follow-up since CTC collection of 16 months (range: 1-30) CellSearch® ≥ 3 CTC (HR 2.77, 95% CI 0.77-9.95) and IsoFlux^TM ≥ 11 CTC (HR 4.14, 95% CI 1.05-16.19) were established as the best cutoff points for predicting survival. Using castPCR^TM we found KRAS mutations in CTC in 4 out of 8 patients from group 1 and in 2 out of 3 patients from group 2. None of these mutations were found in the primary tumor using standard methods, possibly reflecting intratumor heterogeneity or treatment selection pressure. We conclude that IsoFlux^TM is more efficient than CellSearch® in the isolation of CTC in patients with advCRC, achieving, in a majority of cases, the established minimum of CTC for castPCR^TM-based genetic analyses.

Developing prolonged antigen delivery systems that mimick the long-term exposure to pathogens appears as a promising, still poorly explored approach to reach durable immunities. In this study, we have used a simple technology by which his-tagged proteins can be assembled, assisted by divalent cations, as supramolecular complexes with progressive complexity, namely protein-only nanoparticles and microparticles. Microparticles produced out of nanoparticles are biomimetics of secretory granules from the mammalian hormonal system. Upon subcutaneous administration, they slowly disintegrate, acting as an endocrine-like secretory system, and rendering the building block nanoparticles progressively bioavailable. The performance of such materials, previously validated for drug delivery in oncology, has been tested here regarding the potential for time-prolonged antigen release. This has been done by taking, as building blocks, a nanostructured version of p30, a main structural immunogen from the African swine fever virus (ASFV). By challenging the system in both mice and pigs, we have observed unusually potent pro-inflammatory activity in porcine macrophages, and long-lasting humoral and cellular responses in vivo, which might overcome the need for an adjuvant. The robustness of both innate and adaptive responses tag, for the first time, these dynamic depot materials as a novel and valuable instrument with transversal applicability in immune stimulation and vaccinology.

The aim of this study was to describe the trend of traffic accident mortality and social inequalities in Ecuador for the period 2011-2020, distributed by year, gender, age group, geographic location, and type of accident, alongside social disparities. An ecological approach was used to evaluate traffic accident mortality data. The average traffic accident mortality rate in the country during this period was 19.1 per 100,000 inhabitants, with rates being significantly higher in males (31.3) than in females (7.2). The highest mortality rate was recorded in 2011, predominantly impacting the 60 and older age group, the Santo Domingo de los Tsáchilas province, and the Amazon region. The study also noted a declining trend in these rates over the years, with an Annual Percentage Variation of -1.2%. A notable finding was the decrease in traffic accident mortality inequality based on per capita income in 2019, compared to 2011, which rose by 247.7%, whereas the inequality based on illiteracy rates decreased by 18.9% from 2014 to 2019. These findings highlight the significant decrease in traffic accident mortality rates across Ecuador, though marked disparities remain evident across different genders, age groups, and provinces.

Diarrhoea is a serious cause of mortality worldwide that can lead to dehydration, gut barrier function impairment, nutrient malabsorption, and alterations of the gut microbiota (dysbiosis). Current solutions for its management, such as oral rehydration salts (ORS), inhibitors of the gut motility, antibiotics, and living probiotics only partially counteract the mechanisms of the disease and do not provide a full coverage of the problem. Potential risks of the use of living probiotic strains, particularly in immunocompromised patients, can be eliminated with the use of tyndallized (heat-killed) postbiotic bacteria and yeast. ABB C22® is a postbiotic combination of three tyndallized yeasts, namely Saccharomyces boulardii, Saccharomyces cerevisiae, and Kluyveromyces marxianus. To assess the action of the postbiotic combination on diarrhoea, immune and gut epithelial cell signaling assays, gut barrier formation assay and rotavirus gene expression assay were performed. ABB C22® showed a strong anti-inflammatory effect, an induction of the build-up of the gut epithelium, and a degree of protection against rotavirus infection. These experimental studies support the use of the postbiotic ABB C22® as a solution for the management of diarrhoea and gastrointestinal conditions, alone or in combination with existing but incomplete treatments.

The development of high complexity geometry parts is one of the main goals of the additive manufacturing technology. However, the failure of printed structures and the joining of different parts to create complex assemblies represents a real challenge in the research of efficient and sustainability techniques for the permanent assembly of polymers. Laser welding processes have been used as a single step method to join metals until years ago. Nowadays, the growing trend in the use of thermoplastics for additive manufacturing has led to the need to adapt this technique to materials with a very specific nature and more sensitive to thermal effects. Also, the possibility of transmitting the laser beam through transparent polymer layers allows to focus the energy supply on internal sections of the assembled components. In this research, an infrared laser marking system was used to join two different samples of polylactic acid manufactured by fused deposited modeling technology. In order to increase the effectiveness of the bonding process, a transparent and a dark sample have been used as assembly material, focusing the laser beam on the interface area of the two parts. By means of tensile tests, dimensional measurement and the use of optical microscopy techniques, a basis was established that links the supplied energy by laser to the joining performance.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

Eating disorders (EDs) refer to a group of diseases characterized by a strong tendency toward chronicity, often involving distortions in body image distortion and other related symptoms The prevalence of EDs has increased in recent years, specifically in athletic populations. Therefore, the purpose of this study was to analyse risky eating attitudes in a sample of 1102 subjects from Se-ville (Spain): 142 women and 960 men aged between 15-25 years old. An online survey, designed using Google Forms, consisted of three questionnaires (EAT-26, SCOFF, and BITE), were com-pleted individually and anonymously. With regards to the cut-off points, the percentage of posi-tive cases with significant scores was 11.43% for EAT-26, 31.22% for SCOFF and 4.36% for BITE. The study found that the probability of testing positive for EDs is significantly higher in women than in men (p < 0.001). Specifically, the risk attitude for EDs in female athletes measured by the EAT-26 test is three times higher than in male athletes, while the risk attitude measured by the SCOFF test is twice as high in females. Risk attitude for EDs in athletes measured by the BITE test is 8 times higher in females than in males. This study’s findings confirm several important as-sumptions made at the outset of the research. There is indeed a higher risk of EDs in athlete populations. Moreover, all three tests therefore show a higher frequency of possible events of EDs in women, with very similar percentages of difference between sexes. The tests also confirm the role played by the coaches in the prevention of EDs in sports and their capacity to reduce ab-normal food-related behaviours. Thus, the future inclusion of these tests in the screening of athletes is highly recommended.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

Canine mammary tumors (CMT) are the most common cancer in noncastrated female dogs. Interestingly, triple-negative tumors are the most common molecular subtype in female dogs. In this study, we proposed to evaluate the expression of VEGFR-2, PDGFR and microvascular density (MVD) in a group of metastatic and nonmetastatic triple-negative CMT and compare the expression based on clinical parameters. Twenty-six female dogs with triple-negative mammary tumors were divided into three groups: nonmetastatic tumors (NMT) (N=11), tumors with lymph node metastasis (LNM) (N=10) and tumors with lung metastasis (LM) (N=5). We observed increased VEGFR-2 expression in LNM compared with NMT and a positive correlation between tumor grade and VEGFR-2 expression. A positive correlation was noted between VEGFR-2 and PDGFR expression. Regarding microvascular density (MVD), we identified a higher number of vessels in primary tumors with lymph node metastasis and lung metastasis compared with tumors with no metastasis. The primary tumors with lung metastasis exhibited an increased MVD compared with carcinoma with lymph node metastasis. Overall, our results suggest a deregulation of VEGFR-2 and PDGFR and high MVD in metastatic tumors, indicating a role for angiogenesis in tumor progression.

In this paper, a systematic literature review is presented, through a survey in the main digital databases, about modelling methods for Short-Term Load Forecasting (STLF) for hourly electricity demand for residential electricity and to realize the performance evolution and impact of the Artificial Intelligent (AI) in STLF. With these specific objectives, it was developed a conceptual framework on the subject, a systematic review of the literature based on scientific publications with high impact and a bibliometric study directed to the scientific production of AI and STLF. The review of research articles over a 10-year period, which takes place between 2012-2022, uses the Preferred Reporting Items for Systematic and Meta-Analyses (PRISMA) method. This research resulted in more than 300 articles, available in 4 (four) databases: Web of Science, IEEE Xplore, Scopus and Science Direct. The research was organized around 3 (three) central themes, which were defined through keywords: STLF, Electricity, Residential and their corresponding synonyms. 334 research articles were analyzed and identified the year of publication, journal, author, geography by continent and country and the area of application. Of the 334 documents found in the initial research and after applying the inclusion/exclusion criteria, which allowed delimiting the subject addressed in the topics of interest for analysis, 37 (thirty-seven) documents are in English (25 are journal articles and 12 are conference papers). The results point to a diversity of modelling techniques and associated algorithms. The corresponding performance is measured with different metrics and, therefore, cannot be compared directly. Hence, it should be desirable to have a unified data set together with a set of benchmarks with well-defined metrics for a clear comparison of all the modelling techniques and the corresponding algorithms.

Antimicrobial resistance (AMR) is a growing public health concern worldwide, and it poses a significant threat to human, animal, and environmental health. The overuse and misuse of antibiotics have contributed significantly to the emergence and spread of antimicrobial resistance, which may lead to significant economic consequences like reduced productivity and increased healthcare costs. Nanotechnology offers a promising platform for addressing this challenge. Nanoparticles have unique properties that make them highly effective in combating bacterial infections by inhibiting the growth and survival of multidrug-resistant bacteria in three areas of health: human, animal, and environmental. To conduct an economic evaluation of surveillance in this context, it is crucial to have a comprehension of the connections to be addressed by several nations by implementing national action policies based on the One Health strategy. This review provides an overview of the progress made thus far and presents potential future directions to optimize the impact of nanobiotics on AMR.

Innovative tissue engineering biomimetic hydrogels based on hydrophilic polymers have been investigated for their physical and mechanical properties. 5% to 25% by volume loading PHEMA-nanosilica glassy hybrid samples were equilibrated at 37°C in aqueous physiological isotonic and hypotonic saline solutions (0.15 and 0.05 M NaCl) simulating two limiting possible compositions of physiological extracellular fluids. The glassy and hydrated hybrid materials were characterized both for dynamo-mechanical properties and equilibrium absorptions in the two physiological-like aqueous solutions. Mechanical and the morphological modifications occurring in the samples have been described. The 5% volume nanosilica loading hybrid nanocomposite composition showed mechanical characteristics in the dry and hydrated states that were comparable to those of cortical bone and articular cartilage, respectively, and then chosen for further sorption kinetics characterization. Sorption and swelling kinetics were monitored up to equilibrium. Changes in water activities and osmotic pressures in the water-hybrid systems equilibrated at the two limiting solute molarities of the physiological solutions have been related to the observed anomalous sorption modes using the Flory-Huggins interaction parameter approach. The bulk modulus of the dry and glassy PHEMA-5% nanosilica hybrid at 37°C has been observed to be comparable with the values of the osmotic pressures generated from the sorption of isotonic and hypotonic solutions. The anomalous sorption modes and swelling rates are coherent with the difference between osmotic swelling pressures and hybrid glassy nano-composite bulk modulus: the lower the differences the higher the swelling rate and equilibrium solution uptakes. Bone tissue engineering benefits of use of tuneable biomimetic scaffold biomaterials that can be “designed” to act as biocompatible and biomechanically active hybrid interfaces are discussed.

Obstacle-avoidance robots have become an essential field of study in recent years. This paper analyzes two cases that extend reactive systems focused on obstacle detection and its avoidance. The scenarios explored get data from their environments through sensors and generate information for the models based on artificial intelligence to obtain a reactive decision. The main contribution is focused on the discussion of aspects that allow comparing both approaches, such as the heuristic approach implemented, requirements, restrictions, response time, and performance. The first case presents a mobile robot that applies fuzzy logic to achieve soft turning basing its decision on depth image information. The second case introduces a mobile robot based on multi-layer perceptron and ultrasonic sensors to decide how to move in an uncontrolled environment. The analysis of both options offers perspectives to choose between reactive obstacle-avoidance systems based on ultrasonic or Kinect sensors, models that infer optimal decisions applying fuzzy logic or artificial neural networks, with key elements and methods to design mobile robots with wheels. Therefore, we show how AI or Fuzzy Logic techniques allow us to design mobile robots that learn from their “ experience ” by making them safe and adjustable for new tasks, unlike traditional robots that use large programs to perform a specific task.

Background: In recent years, the abusive use of the smartphone has reached a situation that could be considered pathological, although there is no such classification in the DSM-IV. In this sense, different instruments to assess this problematic use or addiction to the smartphone are used. Among them, we found the SPAI, which has been validated in the Spanish language. The main difficulty of these scales is to establish a cut-off point that determines such mobile addiction. On the other hand, self-perception has been used in different addictions as a predictor of the problem. Aim: The objective of this study is to establish the cutting point in the scores of the SPAI scale validated in Spanish, using as a referent the self-perception of addiction values. Methods: A receiver operating characteristics (ROC) analysis was carried out, establishing as the cut-off point the one that presented a higher value of Youden J, indicative of its sensitivity and specificity. Results: 2598 participants from the university community completed the SPAI-Spain questionnaire. When using the self-perception of smartphone addiction as the benchmark value, a score of 44 has been established as the cutting point of the SPAI questionnaire, with a Youden J corresponding to 0.416. Conclusions: The implementation of a cut-off point of the SPAI questionnaire makes it an instrument that allows early identification of those individuals at risk of addiction as well as the establishment of preventive and/or intervention measures.

This article addresses the problem of formation control of a quadrotor and one (or more) marine vehicles operating at the surface of the water with the end goal of encircling the boundary of a chemical spill, enabling such vehicles to carry and release chemical dispersants used during ocean cleanup missions to break-up oil molecules. Firstly, the mathematical models of the Medusa class of marine robots and quadrotor aircrafts are introduced, followed by the design of single vehicle motion controllers that allow these vehicles to follow a parameterized path individually using Lyapunov based techniques. At a second stage, a distributed controller using event triggered communications is introduced, enabling the vehicles to perform cooperative path following missions according to a pre-defined geometric formation. In the next step, a real time path planning algorithm is developed that makes use of a camera sensor, installed on-board the quadrotor. This sensor enables the detection in the image of which pixels encode parts of a chemical spill boundary and use them to generate and update in real time a set of smooth B-spline based paths for all the vehicles to follow cooperatively. The performance of the complete system is evaluated by resorting to 3-D simulation software, making it possible to simulate visually a chemical spill. Results from real water trials are also provided for parts of the system, where two Medusa vehicles are required to perform a static lawn-mowing path following mission cooperatively at the surface of the water.

As an essential component of our innate immune system, the complement system is responsible for our defense against pathogens. The complement cascade has complex roles in the central nervous system (CNS), most of what we know about it stems from its role in brain development. However, in recent years, numerous reports have implicated the classical complement cascade in both brain development and decline. More specifically, complement dysfunction has been implicated in neurodegenerative disorders, such as Alzheimer’s disease (AD), which is the most common form of dementia. Synapse loss is one of the main pathological hallmarks of AD and correlates with memory impairment. Throughout the course of AD progression, synapses are tagged with complement proteins and are consequently removed by microglia which express complement receptors. Notably, astrocytes are also capable of secreting signals that induce the expression of complement proteins in the CNS. Both astrocytes and microglia are implicated in neuroinflammation, another hallmark of AD pathogenesis. In this review, we provide an overview of previously known and newly established roles for the complement cascade in the CNS and we explore how complement interactions with microglia, astrocytes, and other risk factors such as TREM2 and ApoE4, modulate the processes of neurodegeneration in both amyloid and tau models of AD.

The commercial equipment that carries out the measurement of temperature has a high cost. Therefore, this article describes the development of a temperature measurement equipment, which uses a microcontrolled platform, responsible for managing the data of the collected temperature signals and making available the acquired information, so that they can be verified in real time at the measurement site, or remotely. The construction of the temperature measurement equipment was performed using open platform hardware / software, where performance tests were carried out with the objective of developing a temperature measurement equipment that has measurement quality and low cost.

Mucorales are the causal agents for the lethal disease known as mucormycosis. Mortality rates of mucormycosis can reach up to 90%, due to the mucoralean antifungal drug resistance and the lack of effective therapies. A concerning urgency among the medical and scientific community claims to find targets for the development of new treatments. Here, we reviewed different studies de-scribing the role and machinery of a novel non-canonical RNAi pathway (NCRIP) only conserved in Mucorales. Its non-canonical features are the independence of Dicer and Argonautes proteins. Conversely, NCRIP relies on RNA-dependent RNA Polymerases and an atypical ribonuclease III (RNaseIII). NCRIP regulates the expression of mRNAs by degrading them in a specific manner. Its mechanism binds dsRNA but only cuts ssRNA. NCRIP exhibits a diversity of functional roles. It represses the epimutational pathway and the lack of NCRIP increases the generation of drug resistant strains. NCRIP also regulates the control of retrotransposons expression, playing an essential role in genome stability. Finally, NCRIP regulates the response during phagocytosis, affecting the multifactorial process of virulence. These critical NCRIP roles in virulence and antifungal drug resistance, along with its exclusive presence in Mucorales, mark this pathway as a promising target to fight against mucormycosis.

Soil amendments with composted organic materials are recommended to increase soil organic matter (SOM), promote soil fertility, and the Circular Economy. Growing areas of hedged olive groves in southern Iberia peninsula generate huge amounts of olive leaves whose potential as soil organic amendment is not fully studied. An experimental field trial in a hedged olive grove (cv. “Cobrançosa”) was set up near Portalegre, Portugal, to test a compost of olive leaves plus sheep manure (2:1) applied in the row, at soil surface. Three nominal rates (0 or control, 2.5 and 5.0 kg m-2) were used, in a complete randomized block setup (3 treatments, 3 replicas, 9 plots) and soil chemical properties of layers 0-5, 5-15, and 15-30 cm deep were annually monitored. Results (mainly in layer 0-5 cm) showed increases in total N, carbon of the particulate organic matter (POM-C), permanganate oxidizable carbon (POX-C), extractable phosphorus, and zinc, after one year, and increases in soil organic carbon (SOC), C-stock, pHKCl, extractable phosphorus, and zinc, after two years. POX-C was the most sensitive SOM-related indicator, showing increases up to 30 cm deep after one year. This compost improved soil fertility, but should be monitored over longer periods of time, namely for SOC and extractable zinc content.

The scientific fields of complexity, artificial life (ALife), and artificial intelligence (A.I.) share several commonalities: historic, conceptual, methodological, and philosophical. It was possible to develop them only because of information technology, while their origins can be traced back to cybernetics. In this perspective, I'll revise the expectations and limitations of these fields, some of which have their roots in the limits of formal systems. I will use interactions, self-organization, emergence, and balance to compare different aspects of complexity, ALife, and A.I. The paper poses more questions than answers, but hopefully it will be useful to align efforts in these fields towards overcoming --- or accepting --- their limits.

In northern Canada where permafrost is prevalent, a shortage of accessible, affordable, and high-quality housing has been ongoing for decades. Design of foundations in permafrost presents unique engineering challenges due to permafrost soil mechanics and climate change. There is no specific design code for pile or shallow foundations in northern Canada. Consequently, the design process heavily relies on the expertise and experience of Arctic geotechnical engineers who have specialized knowledge in this field. Therefore, a comprehensive review of the practice or literature in foundation design in the Arctic would be necessary. The main objective of this review paper is to provide an overview of the common foundations in permafrost and the techniques adopted to counteract the effects of frozen soils. This study conducted a literature review of state-of-the-art practices on deep and shallow foundations used in northern Canada, including common steel pipe piles and thermosyphons. The review summarized the current principles, including adfreeze strength, creep settlement, and frost heave, used in the foundation design in permafrost. Then this paper summarized the findings from interviewing several engineers or professionals who have experiences in the design of foundations in permafrost. The interviews revealed the technical and non-technical aspects of foundation design practice in northern Canada. Lastly, in order to demonstrate the design methods, the paper presented two examples where screw piles and steel pipe piles were designed to support a residential building in northern Canada, according to the state-of-practice criteria for adfreeze strength, long term settlement and frost heave.

The electronic transport stability in nanodevices composed by metal/trans-polyacetylene /metal with different long length has contributed greatly for performance, homogeneity, stability, organization of the chains, reproducibility and higher conductivity. In this paper, we present an analytical study of the electronic transport characteristics from dimerized trans-polyacetylene (trans-PA) molecules containing an odd-even number of sites coupled to metal leads (left and right) in T-shaped geometry using the extended Su-Schrieffer-Heeger (SSH) model based on tight-binding Hamiltonian with the Non-Equilibrium Green´s Function (NEGF) via Heisenberg´s equation of motion and the Keldysh´s formalism. Due to the complexity of the T-shaped odd-even chain, our proposal was to test the effects on the finite-length network for three, four, five sites and furthermore foresee for 17-sites. We show how to tune dimerization strength () coupling to the parameters and T-shaped geometry of the device to which it affects the overlap integral localized at the three endpoints of the T-shaped system, making both the odd and even chains to undergo a metal-insulator transition in their electronic behavior. The results reached through control parity of the chain plane of the parameters governing () the electronic and experimental tunneling allow a better understanding of the subject.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

We present a model of space that considers it to be a quantized dynamical entity which is a component of the universe along with matter and radiation. The theory is used together with thermodynamic data to provide a new view of cosmic evolution and an insight into the nature of dark energy and dark matter. Space is made up of energy quanta. The universe started from an atomic size volume at very high temperature and pressure near the Planck epoch. Upon expansion and cooling, phase transitions occurred resulting in the formation of radiation, fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters. From a phase diagram of cosmic composition, we obtained a correlation between dark energy and the energy of space. Using the Friedmann equations, data from WMAP studies of the composition of the universe at 3.0 x 10⁵ (a=5.25 x 10^-2) years and at present (a=1), are well fitted by our model with an equation of state parameter, w= -0.7. The accelerated expansion of the universe, starting at about 7 billion years, determined by BOSS measurements, also correlates well with the dominance of dark energy at 7.25 x 10⁹ years ( a= 0.65). The expansion can be attributed to Quintessence with a space force arising from a quantum space field. From our phase diagram, we also find a correlation suggesting that dark matter is a plasma form of matter similar to that which existed during the photon epoch immediately prior to recombination. Our Quantum Space Model leads to a universe which is homogeneous and isotropic without the need for inflation. The thermodynamics of expansion is consistent with BOSS data that show the process to be adiabatic and the rate of expansion decelerating during the first 6 billion years after the Big Bang. However, it became non-adiabatic and accelerating thereafter. This implies an influx of energy from a source outside the universe; it warrants consideration as a possible factor in the accelerated expansion of the universe.

Objective: To evaluate which risk factors contribute directly or indirectly to Toxoplasma gondii infection in patients with ocular toxoplasmosis. Methods: Between 2018-2020, a total of 306 patients were selected, and treated at the Retinology Outpatient Clinic of the Specialty Hospital of Sāo José do Rio Preto, in the state of São Paulo. After the fundoscopy test, the Enzyme Linked Fluorescent Assay (ELFA) was used to determine IgG and IgM class anti-Toxoplasma gondii antibodies. Results: The results showed that individuals aged 60 years or older, and women who had a previous pregnancy, (p=0.000, OR= 8.137 and 95 % CI = 2.562 – 25.844), (p=0.016, OR= 7.395 and CI 95 % = 1,449 – 37,725) respectively, were 48.6 % more likely to develop ocular toxoplasmosis. Conclusion: In this way, previous pregnancy is a risk factor for the reactivation of toxoplasma, as well as for the generation of retinochoroiditis in previously infected women.

We present a thermodynamic approach in modeling the evolution of the universe based on a theory that space consists of energy quanta, the spaceons. From wave-particle duality, they can be treated as an ideal gas. The model is similar to the Big Bang but without Inflation. It provides an insight into the nature of dark energy and dark matter, and an explanation for the accelerated expansion of the universe. The universe started from an atomic size volume of spaceons at very high temperature and pressure. Upon expansion and cooling, phase transitions occurred resulting in the formation of fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters due to the action of gravity. From the cooling curve of the universe we constructed a thermodynamic phase diagram of cosmic composition, from which we obtained the correlation between dark energy and the energy of space. Using Friedmann’s equations, our model fits well the WMAP data on cosmic composition with an equation of state parameter, w= -0.7. The dominance of dark energy started at 7.25 x 10⁹ years, in good agreement with BOSS measurements. The expansion of space is attributed to a scalar quantum space field. Dark Matter is identified as a plasma form of matter similar to that which existed during the photon epoch, prior to recombination. The thermodynamics of expansion of the universe was adiabatic and decelerating during the first 7 billion years after the Big Bang; it accelerated thereafter. A negative pressure for Dark Energy is required to sustain the latter. This is consistent with the theory of General Relativity and the law of conservation of energy. We propose a mechanism for the acceleration as due to consolidation of matter forming Dark Energy Stars (DES) and other compact objects. The resulting reduction in gravitational potential energy feeds back energy for the expansion. Space will continue to expand and dark energy will undergo phase transition to a Bose-Einstein condensate, a superfluid form of matter. Self-gravitation can cause a bounce and start a new Big Bang. We show how the interplay of gravitational and space forces leads to a cyclic, maybe eternal, universe.

Genetic Programming (GP) is a powerful Machine Learning (ML) algorithm that can produce readable white-box models. Although successfully used for solving an array of problems in different scientific areas, GP is still not well known in Remote Sensing. The M3GP algorithm, a variant of the standard GP algorithm, performs Feature Construction by evolving hyper-features from the original ones. In this work, we use the M3GP algorithm on several sets of satellite images over different countries to create hyper-feature from satellite bands to improve the classification of land cover types. We add the evolved hyper-features to the reference datasets and observe a significant improvement of the performance of three state-of-the-art ML algorithms (Decision Trees, Random Forests and XGBoost) on multiclass classifications and no significant effect on the binary classifications. We show that adding the M3GP hyper-features to the reference datasets brings better results than adding the well-known spectral indices NDVI, NDWI and NBR. We also compare the performance of the M3GP hyper-features in the binary classification problems with those created by other Feature Construction methods like FFX and EFS.

A via ferrata (from the German “klettersteig”, hereinafter VF) is a sports route located on forest and mountains vertical rock walls equipped with steps, chains, artificial dams, bridges and other fixed elements and which have a steel cable (safety cable) all the way along allowing users to secure their progress and avoid possible falls [1]. This article aims to analyse the state of the art of the VF sector in Spain, especially in terms of the regulations of obligatory compliance, in addition to defining the basic characteristics of the installations to ensure that these are safe for users, providing a previously non-existent summary of the most important recommendations regardless of the country where they are installed.

Desmoplastic small round cell tumor (DSRCT) is an extremely rare, aggressive sarcoma affecting adolescents and young adults with male predominance. Generally, it originates from serosal surface of abdominal cavity. The hallmark characteristic of DSRCT is the EWSR1-WT1 gene fusion. This translocation up-regulates the expression of PDGFRα, VEGF and other proteins related to tumor and vascular cell proliferation. Current management of DSRCT includes a combination of chemotherapy, radiation and aggressive cytoreductive surgery plus intra-peritoneal hyperthermic chemotherapy (HIPEC). Despite advances in multimodal therapy, outcomes remain poor since the majority of patients present disease recurrence and die within 3 years. The dismal survival makes DSRCT an orphan disease with urgent need of new drugs. The treatment of advanced and recurrent disease with tyrosine kinase inhibitors, such as pazopanib, sunitinib, and mTOR inhibitors have been evaluated in small studies. Recent works using comprehensive molecular profiling of DSRCT identified potential therapeutic targets. In this review, we aim to describe the current studies conducted to better understand DSRCT biology and to explore the new therapeutic strategies under investigation in preclinical models and in early phase clinical trials.

When we attempt to define life, we tend to refer to individuals, those that are alive. But these individuals might be cells, organisms, colonies... ecosystems? We can describe living systems at different scales. Which ones might be the best ones to describe different selves? I explore this question using concepts from information theory, ALife, and Buddhist philosophy. After brief introductions, I review the implications of changing the scale of observation, and how this affects our understanding of selves at different structural, temporal, and informational scales. The conclusion is that there is no single ``best'' scale for a self, as this will depend on the scale at which decisions must be made. Different decisions, different scales.

The Musa textilis var. Abuab has high fiber quality (FQ) but has low resistance against abaca bunchy top virus (AbBTV); the Musa balbisiana var. Pacol, has low FQ but high resistance against AbBTV. Their backcrosses (BC2 and BC3) possess both desirable traits. Analysis using RNA-seq showed that the regulatory divergence of Abuab and Pacol is largely explained by cis differences with 27.4% and 22.3% if we are to assess it using BC2 and BC3, respectively. Cis differences between the two genotypes are significantly reduced from BC2 to BC3 due to changes in genomic constitution. Trans, on the other hand, is robust to changes in allelic composition. All these are attributed to the loss of heterozygosity in the BC3 relative to BC2. Further analysis showed that both backcrosses exhibited genome-wide preferential expression of Pacol- over Abuab-specific alleles, despite the wider genetic presence of the latter in the hybrids. The ratio of the two genotype-specific expressed transcripts and the ratio of their corresponding genetic make-up are significantly disproportionate, a phenomenon which we refer here as “genome–transcriptome incongruence”. We also observed preferential expression switching in which several genes prefer Abuab- (or Pacol-) specific allele in the BC2 but switched to Pacol- (or Abuab-) specific allele in the BC3 genome.

Climate change has become a major concern for developing countries given the risk that it posses on energy and food independence, and on general productivity. Despite having an energy system with low carbon intensity when compared to other Latin American countries, Colombia is already facing climate change impacts and requires urgent efforts to mitigate them. As a developing country, the challenge is bigger as policies for economic growth should be in line with the global commitment of reducing greenhouse gas emissions. With the aim of contributing to the design of climate policies, this study assesses the impact of economic development on the environment by examining the validity of the Environmental Kuznets Curve hypothesis for Colombia. Statistically validated and stable autoregressive distributed lag models are estimated for three different environmental indicators: carbon dioxide emissions, methane emissions, and ecological footprint. Moreover, the effects of other variables such as urbanization, foreign direct investment, value added of agricultural and industrial sectors, and energy use are analyzed with dynamic simulations. Empirical evidence supports a long-run equilibrium relationship among investigated variables and the existence of an inverted U-shaped EKC relationship between Gross Domestic Product (GDP) and methane emissions, and GDP and ecological footprint. Shifting to renewable energy sources and leveraging the use of cleaner technologies in agricultural and industrial sectors are found to be key for economic growth without harming the environment.