A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

The physical roots, interpretation, controversies and precise meaning of the Landauer Principle are surveyed. Landauer's principle is a physical principle pertaining to the lower theoretical limit of energy consumption of computation. It states that an irreversible change in information stored in a computer, such as merging two computational paths, dissipates a minimum amount of heat kBTln2 per a bit of information to its surrounding. The Landauer Principle is discussed in the context of fundamental physical limiting principles, such as the Abbe diffraction limit, the Margolus-Levitin limit and the Bekenstein limit. Synthesis of the Landauer bound with the Abbe, Margolus-Levitin limit and Bekenstein limits yields the minimal time of computation, which scales as τmin~hkBT. Decrease in a temperature of a thermal bath will decrease the energy consumption of a single computation, but, in parallel, it will slow the computation. The Landauer principle bridges between John Archibald Wheeler “it from bit” paradigm and thermodynamics. Experimental verifications of the Landauer Principle are surveyed. Interrelation between thermodynamic and logical irreversibility is addressed. Generalization of the Landauer principle to the quantum and non-equilibrium systems is addressed. Landauer Principle represents the powerful heuristic principle bridging the physics, information theory and computer engineering.

Disk galaxies have a typical dimension of few tens of thousands of light years. It follows from the theory of general relativity that any signal originating from the galactic center will be noticed at the outskirts of the galaxy only tens of thousands of years later. This retardation effect is absent in modelling used to calculate rotation curves throughout the entire galaxy and its external gas. The considerable differences between Newtonian action at a distance predictions and observed velocities are currently removed either by assuming dark matter or by suggesting various modifications to the laws of gravity, MOND being a long standing alternative to Newtonian gravity. In previous papers we have shown that applying general relativity in a rigorous fashion without mindlessly neglecting retardation, one can explain the radial velocities of galactic matter without modifying gravity or adding unseen matter. Moreover, it was shown that dark matter effects as they appear in gravitational lensing, the Tully-Fisher relation, and mass estimations based on the virial theorem could also be explained as retarded-gravity effects. In the original main paper on the subject only one galaxy (M33) was analysed in detail. This was later amended somewhat with a published study of eleven galaxies. Here we give a more comprehensive retardation analysis of 143 galaxies of different types from the SPARC Galaxy collection. We show that in most cases we obtain an excellent fit without postulating dark matter or modifying general relativity.

Residual sugars (RS) in wine are the sugars that remain in a wine after fermentation is complete. In some wine styles, such as semi-dry wines, the accurate measurement of the RS concentration is critical for both qualitative and legislative reasons. Brix, measured by a simple refractometer, can give a good estimation of the RS concentration in the must, but during fermentation, the presence of alcohol leads to inaccurate sugar measurements. In order to measure the RS accurately, other more precise techniques are used, most of which are expensive or require professional skills. Therefore, novel approaches for rapid, easy, and practical measurements for estimating the sugar content were suggested over the years. However, most of these methods do not supply an actual measurement of RS but rather give brix values, and those that measure RS involve special equipment, which is less relevant for small wineries. This study suggests a novel model for predicting and controlling the wine's residual sugar. The data the model uses is the initial brix of the must before fermentation and its density during fermentation. The model was created by measuring actual residual sugars during the fermentation of natural and synthetic musts, with various degrees of initial brix levels, while simultaneously measuring their densities and correlating the two measurements. Linear regression between the residual sugar of the wine and its density was obtained for all treatments and repetitions (i.e., different values of must initial brix) with R² values above 0.97. Using the model, one can calculate (before commencing the fermentation) the density values at which the fermentation will reach a particular desired residual sugar value for a specific initial brix level; the model is applicable for the fermentation conditions used in this work, i.e., brix levels of 18-27˚Bx, Saccharomyces cerevisiae strains (fx-33 and fx-10) in common conditions of fermentation regarding temperature and aeration.

This paper investigates nonverbal communication in human interactions, with a specific focus on facial expressions. Employing a Long Short-Term Memory (LSTM) architecture and a custom-ized facial expression framework, our approach aims to improve virtual agent interactions by incorporating subtle nonverbal cues. The paper contributes to the emerging field of facial expres-sion generation, addressing gaps in current research and presenting a novel framework within Unreal Engine 5. The model's architecture, trained on the CANDOR corpus, captures temporal dynamics, and refines hyperparameters for optimal performance. During testing, the trained model showed a cosine similarity of -0.95. This enables the algorithm to accurately respond to non-verbal cues and interact with humans in a way that is comparable to human-human interac-tion. Unlike other approaches in the field of facial expression generation, the presented method is more comprehensive and enables the integration of a multi-modal approach for generating facial expressions. Future work involves integrating blendshape generation, real-world testing, and the inclusion of additional modalities to create a comprehensive framework for seamless hu-man-agent interactions beyond facial expressions.

Entropic Dynamics (ED) is a framework in which Quantum Mechanics is derived as an application of entropic methods of inference. In ED the dynamics of the probability distribution is driven by entropy subject to constraints that are codified into a quantity later identified as the phase of the wave function. The central challenge is to specify how those constraints are themselves updated. In this paper we review and extend the ED framework in several directions. A new version of ED is introduced in which particles follow smooth differentiable Brownian trajectories (as opposed to non-differentiable Brownian paths). To construct the ED we make use of the fact that the space of probabilities and phases has a natural symplectic structure (i.e., it is a phase space with Hamiltonian flows and Poisson brackets). Then, using an argument based on information geometry, a metric structure is introduced. It is shown that the ED that preserves the symplectic and metric structures -- which is a Hamilton-Killing flow in phase space -- is the linear Schrödinger equation. These developments allow us to discuss why wave functions are complex and the connections between the superposition principle, the single-valuedness of wave functions, and the quantization of electric charges. Finally, it is observed that Hilbert spaces are not necessary ingredients in this construction. They are a clever but merely optional trick that turns out to be convenient for practical calculations.

Ultrathin Bi₂Se₃-NbN bilayers comprise a simple proximity system of a topological insulator and an s-wave superconductor for studying gating effects on topological superconductors. Here we report on 3 nm thick NbN layers of weakly connected superconducting islands, overlayed with 10 nm thick Bi₂Se₃ film which facilitates enhanced proximity coupling between them. Resistance versus temperature of the most resistive bilayers shows insulating behavior but with signs of superconductivity. We measured the magnetoresistance (MR) of these bilayers versus temperature with and without a magnetic field H normal to the wafer (MR=[R(H)-R(0)]/\{[R(H)+R(0)]/2\}), and under three electric gate-fields of 0 and ±2 MV/cm. The MR results showed a complex set of gate sensitive peaks which extended up to about 30 K. The results are discussed in terms of vortex physics, and the origin of the different MR peaks is identified and attributed to flux-flow MR in the isolated NbN islands and the different proximity regions in the Bi₂Se₃ cap-layer. The dominant MR peak was found to be consistent with enhanced proximity induced superconductivity in the topological edge currents regions. The high temperature MR data suggest a possible pseudogap phase or a highly extended fluctuation regime.

The classical Lotka-Volterra predator-prey model is globally stable and uniformly persistent. However, in real-life biosystems extinction of species due to stochastic effects is possible. In this paper, we consider the classical Lotka-Volterra predator-prey model under stochastic perturbations. For this model, using an analytical technique based on the direct Lyapunov method and a development of the ideas of R.Z. Khasminskii, we find the precise sufficient conditions for the stochastic extinction of one and both species and the precise necessary conditions for the stochastic system persistence. The stochastic extinction occurs via a process known as the stabilization by noise of the Khasminskii type, and, in order to establish the sufficient conditions for extinction, we found the conditions for the stabilization. The analytical results are illustrated by numerical simulations. {\bf Keywords:} stochastic perturbations, white noise, Ito's stochastic differential equation, the Lyapunov functions method, stability in probability, stabilization by noise, stochastic extinction, persistence.

Although the water absorption feature (WAF) at 970 nm is not very well-defined, it may be used alongside other indices to estimate the canopy water content. The individual performance of a number of existing vegetation water content (VWC) indices against the WAF is assessed using linear regression model. We developed a new Combined Vegetation Water Index (CVWI) by merging indices to boost the weak absorption feature. CVWI showed a promise in assessing the vegetation water status derived from the 970 nm absorption wavelength. CVWI was able to differentiate two groups of dataset when regressed against the absorption feature. CVWI could be seen as an easy and robust method for vegetation water content studies using hyperspectral field data.

The field of water management is continually changing. Water has been subject to external shocks in the form of climate change and globalization. Analysis of water management is subject to disciplinary developments and inter-disciplinary interactions. Are these developments well documented in the literature? Initial observations on interdisciplinary literature suggest that results are fragmented, implying that a state-of-the-art review is needed. The objective of this paper is to close this gap by reviewing recent developments in water economics that address the increasing perceptions of water scarcity by looking first at changes in supply and quality of water, and then at impacts of climate change on water extremes. Among responses to such challenges, the paper identifies changes to water use patterns by including and co-managing water from different sources—surface and groundwater, wastewater, and desalinated water. Technological advancements also are among the resources that address water challenges. Water challenges reflect also on management of internationally shared water. A recent surge in scientific work identified international treaties as playing a significant role in water management. The paper reviews recently employed economic tools, such as experimental economics, game theory, institutional economics, and valuation methods. And finally, it explores modeling approaches, including hydro-economic and computable general equilibrium models that are being used to deal with water challenges.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

A qualitative analysis of pressure acting within the human eye is presented. The situation emerging within the human eye in rest and human eye of accelerated/training person should be distinguished. When the person is in rest, the hydrostatic pressure is much larger than the Laplace pressure. The dynamic (Bernoulli pressure) emerging from intraocular flows in this case is negligible. The situation is rather different for accelerated or decelerated person. In this case, the dynamical pressure and the water hammer pressure become dominant. Under certain circumstances, the water hammer pressure may be larger than the ultimate tensile strength of retina, choroid and the Bruch membrane‐choroid complex, which may possibly affect the retina. As a recommendation: physical training, which is not accompanied with ultimate acceleration/acceleration of the body, may be performed after posterior vitreous detachment; however, potentially traumatic activities such as boxing or competitive diving should be avoided.

Conventional academic debate on sustainability and transformation has begun to be disputed by researchers, policymakers and other stakeholders from the private sector. The complexity of linking sustainability with transformation necessitates the development of new ways of understanding and explaining actors, processes, issues, structures, and outcomes related to transformation to sustainability (T2S). A persistent problem in understanding and managing the T2S is the implied notion of a monolithic transformation to achieve sustainability. This notion underestimates the diversity of actors as well as the historical contexts of transformations. At the same time, achieving T2S is highly dependent on technical solutions as well as policies that can stir needed behavioural change, whereas these technical solutions and policies are not always socially acceptable or politically implementable. Therefore, achieving T2S also calls for evaluating normative foundations of policies and actions needed to advance T2S. This article argues that T2S is composed of different phases, each of which having a different set of actors, resources and audience. This article explains how collective decision can be achieved through multiple levels and types of negotiations that occur in an orchestrated manner. To understand this, this article introduces a theoretical model as an analytical framework to structure how T2S unfolds. This model uses insights from negotiation studies to focus on the actors’ perspectives on T2S. It proposes the division of the transformation process into phases – entry point, learning, sequencing, disrupting and fortifying. Using the Germany’s energy transition (Energiewende), each of these phases is analysed to determine the “quality” of cooperation that can help fulfil the tasks required to master the so-called “cognitive games” of T2S (ripeness game, power game, bargaining game, policy game, scaling game). Moreover, insights are presented to explain how the designated milestone can be achieved that indicates the advancing to the next phase and eventually entrench the transformation process. The lessons and findings resulting from the analysis of the phases of T2S suggest that there is also the need to revisit underlying assumptions on negotiations, sustainability and transformation.

The hyper-arid environment is characterized by high inter-annual climatic fluctuations. The yearly average rainfall can change substantially for several years, forming wet or dry sub-periods. Observing rainfall trends over a sub-period can lead to a false perception of a change in the trend but may in fact represent a periodic cycle when examined on a larger time scale. We aimed to better characterize the rainfall regime prevailing in the hyper-arid Arava Valley (Israel/Jordan), and to examine the response of vegetation to annual rainfall. We hypothesized that annual and perennial vegetation would respond differently to wet and dry sub-periods, and that grazing activities will impact vegetation growth. We used a time series of monthly rainfall, from which we calculated Standard Precipitation Index (SPI), and calculated proxies of perennial and annual vegetation over the last four decades using Landsat-derived Normalized Difference Vegetation Index (NDVI). We found no clear trend in rainfall amounts during this period, however we did identify wet and dry sub-periods which were statistically distinct in rain and in vegetation patterns from each other. The highest levels of correlation between rainfall and the NDVI derived proxies were found when examining average rainfall over a period of two- three years for the annual vegetation and over four years for perennial vegetation. Using the Mann-Kendall test, we identified a time lag of two to four years, with the proxies of annual vegetation responding faster than the proxies of perennial vegetation, to shifts between wet and dry sub-period. In addition, we found a consistent difference between natural vegetation cover in Jordan (grazed) and Israel (non-grazed), favoring the development of natural vegetation on the Israeli side. We conclude that integrating between long-term remote sensing satellite imagery and climatic records revealed the greater resilience of perennial vegetation in the hyper-arid region to climatic fluctuation, and enabled us to identify the vegetation’s sensitivity to anthropogenic impact.

The blood counts of α thalassemia carriers (α-thal) are similar to those of β thalassemia carriers, except for Hgb A2 that is not elevated. The objective of this study was to determine whether mathematical formulas are effective for detecting suspected α-thal. The data were obtained from the database of the prevention program for detecting couples at risk for having a child with hemoglobinopathy. RBC indices were analyzed using mathematical formulas and the sensitivity and negative predictive value (NPV) calculated. Among 1334 blood counts suspected α-thal analyzed, only the Shine&Lal and the Support Vector Machine formulas revealed high sensitivity and NPV. Sensitivity was 85.54 and 99.33% and NPV 98.93 and 99.93%, respectively. Molecular defects were found in 291, 81 had normal α genes. Molecular analysis was not performed in 962. Based on these results, mathematical formulas incorporating one of these reliable formulas for detecting suspected α or β thalassemia carriers in the program of the automatic analyzers can flag these results and increase the awareness of the primary physicians about the carrier risk and send an alert with a recommendation for further testing.

A formulation of the Density Functional Theory (DFT) is constructed as an application of the method of maximum entropy for an inhomogeneous fluid in thermal equilibrium. The use of entropy as a systematic method to generate optimal approximations is extended from the classical to the quantum domain. This process introduces a family of trial density operators that are parametrized by the particle density. The optimal density operator is that which maximizes the quantum entropy relative to the exact canonical density operator. This approach reproduces the variational principle of DFT and allows a simple proof of the Hohenberg-Kohn theorem at finite temperature. Finally, as an illustration, we discuss the Kohn-Sham approximation scheme at finite temperature

Natural springs, recognized as biodiversity hotspots and keystone ecosystems, exert positive ecological influences beyond their immediate extent, particularly in dryland environments. The water feeding these springs, largely governed by natural climatic conditions, is susceptible to anthropogenic impacts. The objective of this study was to determine the factors that cause fluctuations in water availability to springs of the hyper-arid Arava Valley (Israel/Jordan). Using the Standard Precipitation Index, we statistically classified the historical record of yearly rainfall for the past four decades into clusters of dry and wet sub-periods. We assessed changes in vegetation cover around the springs using the Landsat-derived Normalized Difference Vegetation Index (NDVI) for each sub-period. To assess the anthropogenic effects, we examined the correlations between vegetation cover, water extraction from the aquifer, and the status of adjacent agricultural plots that share a hydrological connection with the springs. Our findings reveal fluctuations between wet and dry sub-periods over the last four decades. We observed high responsiveness of vegetation cover around the springs to these fluctuating sub-periods. Of the 25 studied springs, 12 were directly influenced by anthropogenic factors — seven experienced a decline in vegetation which we attributed to water extraction from the aquifers, while vegetation increase in five springs was attributed to water seepage from agricultural areas upstream. In conclusion, addressing vital habitats such as natural springs in arid drylands requires a holistic approach that integrates long-term climatic, ecological, and anthropogenic observations.

We propose a novel moving median estimator specifically designed for online detection of threshold crossings in multi-channel signals, such as extracellular neural recordings. This estimator offers two key advantages: a reduced sensitivity to outliers and the elimination of memory requirements for storing arrival times. Furthermore, its design facilitates parallel implementation on FPGAs, making it ideal for real-time processing of multi-channel recordings.

Background: Data suggest that food allergies greatly impact a child’s health and growth due to inadequate nutrient intake. Our study aimed to establish the long-term outcome of children with food allergies compared to a control group. Methods: This study was a retrospective cohort study with longitudinal follow-up with a mean period of 4.85 years from the diagnosis to the last study visit. The patients’ nutritional intake was assessed using a three-day food diary and analysed by a dietitian. Patients (61 boys and 33 girls, mean age 6.9 years) had a single food allergy including 21 patients with cow’s milk, 34 with egg, and 39 with peanut allergies. The control group included 36 children (19 boys and 17 girls, mean age 8.03 years). Blood analysis was performed on all participants. Results: Data from our study showed that patients with cow’s milk, egg or peanut allergies had normal growth and achieved catch-up growth from the diagnosis until the last study visit. In the cow's milk allergy group, the allergy was shown to affect calcium intake (p<0.05), while egg and peanut allergies did not impact the dietary intake of nutrients. None of the investigated food allergies affected blood results (p<0.05). Conclusions: In the present study, we showed that single food allergies do not compromise growth in children if they are provided with appropriate support and that the affected children reach catch-up growth from the diagnosis.

The manuscript delves into the intricacies of food production chains, offering a comprehensive breakdown of their components. Moreover, it sheds light on the initiatives orchestrated by government agencies to endorse sustainable practices and fortify areas of opportunity for producer organizations. While the context paints a broad picture, we contend that, to the best of our knowledge, there exists no comparable publication that succinctly encapsulates the role of government in bolstering food production chains. The document unfolds with a detailed exploration of the interaction mechanisms among the various components of the chain. Subsequently, it introduces a set of twelve elements meticulously outlining the multifaceted role of the government. Each element undergoes thorough scrutiny, fostering a nuanced understanding of the intricate relationship between the food production chain and the government's pivotal role in enhancing stability and efficiency. In conclusion, the manuscript not only lays bare the structural elements of food production chains but also presents a unique and in-depth analysis of the government's role, encapsulated within the framework of twelve essential elements.

Indonesia is an interesting case study for students of sustainable development and sustainable energy due to its ability to connect the multiple “worlds” it has become part of. Indonesia is an important bridge to Muslim countries, the voice of the Global South in the G20 and a main pillar of the 134-country-strong G77. Indonesia’s development trajectory is also key to the achievement of the Paris Climate Agreement as well as of the 2030 Agenda. Students can learn from how Indo-nesia address contradictions that would have been unsurmountable for other countries. Indone-sia’s energy transition offers helpful lessons, because of its aspiration to become a developed country by 2045. This goal is only possible when a country is able to effectively address barriers and caveats to sustainable energy. It is interesting how Indonesia focuses on silver linings and come up with pragmatic solutions to energy-related issues. This is followed by the “teaching guide,” which provides recommendations how the lessons from Indonesia can be embedded into a learning experience. The “learning activation approach” is introduced, which encourages stu-dents to systematically reflect on the complexity of selected contexts and understand this com-plexity by looking at the technical issues and processes that allow decision-making.

The energy sector plays an important role in Mexico’s development trajectory. Mexico makes an interesting case study, because it shows how difficult it is to reduce fossil energy dependence despite geographic and climatic conditions that favour renewable energy deployment and use. Resolving path dependencies and the related carbon lock-in are key to Mexico’s sustainable energy transition. This case study aims to identify and discuss how carbon lock-in affects Mexico’s sustainable energy transition. Mexico’s carbon lock-in involves oil and oil-run power plants that are costly to build but relatively inexpensive to operate. This case study identifies potential entry points for transitioning towards sustainable energy in Mexico – resources that can promote the use of clean energy despite carbon lock-in. For example, focusing on electrification – particularly of the carbon-intensive sectors – can help Mexico transit towards sustainable energy despite institutional constraints. Complementing this case study is a teaching guide with recommendations for using Mexico’s energy transition in courses on sustainability. It introduces a “learning activation framework” to identify emerging opportunities that can advance sustainable energy transitions in different cases of carbon lock-in. Finally, the framework also gives students a chance to help dismantle or cope with carbon lock-ins.

Introduction: Fractures in older individuals are often caused by falls, with approximately 90% of hip fractures resulting from falls. The risk of falling increases with age, and while a significant portion of individuals over 65 fall at least once per year, only a small percentage of these falls result in hip fractures. Factors that influence the likelihood of a fracture occurring include the intensity of the fall and the quality of the bone, with lower bone mineral content increasing the risk of fracture. Older women, particularly those in their 70s, are significantly more prone to hip fractures and any type of fracture. Efforts to reduce the likelihood of falls or mitigate the associated trauma are more complex than treating osteoporosis, due in part to a lack of understanding of the causes and contributing factors of falls in older age.Methods: This study analyzed data from patients admitted to Carmel medical center with upper or lower limb fractures between 2017 and 2019 to determine the side of wrist fractures and compare it to patient age in order to examine whether there was a difference in the distribution of sides in distal radius fractures based on age and test the hypothesis that falls are more likely to occur on the left side due to the assumption that dominant hand gross motor skills are better preserved. The study received approval from the Institutional Helsinki Committee and used statistical analysis with a significance level of 0.05. Potential sources of bias include limited availability of reliable data for many patients and the risk of errors in fracture registration or diagnosis, although the small sample size is expected to minimize these biases.Results: In this analysis of patient data from 2019 to 2017, a binomial test found that the probability of breaking the left wrist is significantly greater than the probability of breaking the right wrist (p < 0.05), while a t-test found no difference in the distribution of fractures between the right and left wrists of the distal radius based on age (p = 0.2774). Discussion: The findings of the study are consistent with previous research, and indicate that there is no change in side preference for fractures with age. Conclusion: The probability of breaking the left wrist is approximately 1.5 times greater than the probability of breaking the right wrist.

This study focused on evaluating the potential of natural fermentation of pea flour (F) to improve the release of antioxidant compounds. Two fermentation conditions of F were performed: 1: 36.4% w/w, 24 h, 30°C (FF1); 2: 14.3% w/w, 24 h, 37°C (FF2); pH values decreased to 4.4-4.7, with a predominance of lactic acid bacteria. An increment of the proteolysis degree (TNBS method) (greater for FF2), polypeptides aggregation and decrease of solubility, increase of &lt; 2 kDa peptides, and increase in the ORAC potency of PBS-soluble fractions after fermentation was demonstrated. After simulated gastrointestinal digestion (SGID, COST-INFOGEST), FF1D and FF2D showed greater proteolysis degrees (63 and 53%) than F1D and F2D (45%), with differences in the molecular composition of the different digests. ORAC and HORAC potencies increased in all cases. FF2D presented the greater ORAC value, with higher activities for &gt; 4 kDa, some in the range 2 to 0.3 kDa. and &lt; 0.10 kDa fractions. Fermentation also increased the 60 % ethanol extracted phenolic compounds, mainly flavonoids, and the ORAC activity. After SGID, the flavan-3-ols disappeared but some phenolic acids increased respect to F. Fermentation in condition 2 was considered the most appropriate to obtain a functional antioxidant ingredient.

The potentiality of cv. Malbec grape pomace (GP) as a functional ingredient in the formulation of bakery foods (muffins, biscuits and cereal bars) was studied. The effect of GP addition on the phenolic compounds (PCs) composition, nutritional and sensory properties were evaluated. The addition of GP increased the content of dietary fiber, proteins, ash, total phenolic content (TPC), antioxidant activity (AA), anthocyanins and non-anthocyanins PCs while decreasing the carbohydrates content. The main PCs given by the GP to supplemented foods were (-)-gallocatechin, quercetin-3-O-glucoside, rutin, caffeic acid, syringic acid and (+)-catechin. For anthocyanins, the acylated derivatives were more stable to heat treatment (baking) in food processing which was evidenced by a higher proportion of these PCs compounds when compared to the same derivatives quantified in GP. In general, when the TPC or individual concentrations of PCs were analyzed in a nutritional or functional context, one portion of the supplemented foods showed levels high enough to satisfy the recommended dose per day of these bioactive compounds. Additionally, the foods were well received by consumers during the sensory evaluation and supplemented biscuits got the highest acceptability. This study demonstrated that GP could be a viable functional ingredient in bakery foods to give nutritionally enhanced properties like TPC, PCs, AA and dietary fiber in consumer’s diets.

Clinical screening tests for balance and mobility often fall short of predicting fall risk. Cognitive distractors and unpredictable external stimuli, common in busy natural environments, contrib-ute to this risk, especially in the elderly. Less is known about the effects of upper sensory-motor coordination such as coordinating one’s hand with an external stimulus. We combined move-ment sonification and affordable inertial motion sensors to develop a task for the precise meas-urement and manipulation of full-body interaction with stimuli in the environment. In a double-task design, we studied how a supra-postural activity affected quiet stance. The supra-postural task consisted of rhythmic synchronization with a repetitive auditory stimulus. The stimulus was attentionally demanding because it was being modulated continuously. The participant’s hand movement was sonified in real-time, and their goal was to synchronize their hand move-ment with the stimulus. In the unpredictable condition, the tempo changed at random points in the trial. A separate sensor recorded postural fluctuations. Young healthy adults were compared to elderly participants without known risk of falling. Results supported the hypothesis that su-pra-postural coordination would entrain postural control. The effect was stronger in the elderly, supporting the idea that diminished reserve capacities reduce the ability to isolate postural con-trol from sensory-motor and cognitive activity.

Characterised by the growth of benign tumours, fibropapillomatosis (FP) is a debilitating disease that predominantly afflicts the endangered green turtle (Chelonia mydas). A growing body of histological and molecular evidence has consistently associated FP tumours with Chelonid alphaherpesvirus 5 (ChHV5), leading this virus to be considered the most likely aetiological agent of FP. However, a recent study which detected both ChHV5 and Chelonia mydas papillomavirus 1 (CmPV1) DNA in FP tumour tissues has challenged this hypothesis. The present study aimed to establish the wider prevalence of CmPV1 and co-occurrence with ChHV5 in marine turtles in waters adjacent to the east coast of Queensland, Australia. This comprehensive molecular survey screened a total of 353 samples from 275 foraging turtles using probe-based qPCR. Three sample categories were used in this study: Group A (FP tumours), Group B (non-tumoured skin from turtles with FP tumours) and Group C (non-tumoured skin from turtles without FP tumours). Concurrent detection of ChHV5 and CmPV1 DNA is reported for all three categories, with the highest rate of concurrent detection reported for Group A samples (43.5%). Collectively, these results pivot the way we think about FP; as an infectious disease where two separate viruses may be at play.

Many physiotherapy treatments begin with a diagnosis process. The patient describes symptoms, upon which the physiotherapist decides which tests to perform until a final diagnosis is reached. The relationships between the anatomical components are too complex to keep in mind and the possible actions are abundant. A trainee physiotherapist with little experience naively applies multiple tests to reach the root cause of the symptoms, which is a highly inefficient process. This work proposes to assist students in this challenge by presenting three main contributions: (1) A compilation of the neuromuscular system as components of a system in a Model-Based Diagnosis problem; (2) The PhysIt is an AI-based tool that enables an interactive visualization and diagnosis to assist trainee physiotherapists; and (3) An empirical evaluation that comprehends performance analysis and a user study. The performance analysis is based on evaluation of simulated cases and common scenarios taken from anatomy exams. The user study evaluates the efficacy of the system to assist students in the beginning of the clinical studies. The results show that our system significantly decreases the number of candidate diagnoses, without discarding the correct diagnosis, and that students in their clinical studies find PhysIt helpful in the diagnosis process.

Previous research has explored different models of synchronous remote learning environments supported by videoconferencing and virtual reality platforms. However, few studies have evaluated the preference and acceptance of synchronous remote learning in a course streamed in an immersive or augmented reality platform. This case study uses ANOVA analysis to examine the engineering students´ preferences for receiving instruction during the COVID19 pandemic in three classroom types: face-to-face, conventional virtual (mediated by videoconferencing) and an immersive virtual classroom (IVC). Likewise, structural equation modeling, was used to analyze the acceptance of the IVC perceived by students, this includes four latent factors: ease of receiving a class, perceived usefulness, attitude towards IVC and IVC use. The findings showed that the IVC used in synchronous remote learning has a similar level of preference to the face-to-face classroom, and higher than the conventional virtual one. Despite the high preference for receiving remote instruction in IVC, aspects such as audio delays that affect interaction still need to be resolved. On the other hand, a key aspect for a good performance of these environments is the dynamics associated with the teaching-learning processes and the instructor´ qualities.

Deforestation is an important environmental problem in México and a key promoter of regional climate change through modifying the surface albedo. The objective of this research was to characterize the impact of deforestation and land use changes on surface albedo (α) and climate patterns in the Municipality of Tapalpa, Jalisco, México between the years 2014 and 2021. The main land cover types are coniferous forests (CF), oak and gallery woodlands (OGW), and annual agriculture (AA); which represent more than 88% of the regional territory (1066.03 km2). We used 2014 and 2021 Landsat 8 OLI images with topographic and atmospheric correction, in order to develop an inventory of albedo values for each land cover type in both time scenarios. Albedo images were generated by using the equation proposed by Liang in 2001, which is based on the reflectance of the bands 2, 3, 4, 5, and 7. Differences in albedo values were calculated between the years 2014 and 2021, and those differences were correlated with variations in climate parameters, for which we used climate data derived from the WRF model. In addition, the different land use changes found were classified in terms of triggers for increasing or decreasing surface albedo. Results showed that between 2014 and 2021, at least 38 events of land use change or deforestation occurred, with albedo increments between 1 and 11%, which triggered an average increment of 0.57% of the regional surface albedo in comparison to 2014 scenario. From 2014 to 2021, the albedo for CF, OGW, and AA, increased significantly (p&lt;0.001; Mann-Whitney U Test) by 79, 12, and 9%, respectively. In addition, the regional albedo increment was found to be significant and negatively correlated (p&lt;0.01 Spearman’s coefficient) with relative humidity (RH), maximum temperature (Tmax), minimum temperature (Tmin), and diurnal thermal range (DTR). The decrease in the regional values of relative humidity in 2021, occurred even when in that year the annual precipitation levels were higher than those of 2014, hence, reinforcing the fact of a possible climatic effect of the regional albedo changes. Conversion of CF and OGW into AA, perennial agriculture (PA), or grassland (GR) always yielded an albedo increment, whilst the conversion of AA to irrigation agriculture or PA triggered a decrease in albedo, and finally, the pass from GR or AA to protected agriculture caused albedo increase or decrease, depending on the greenhouse covers materials. Reducing deforestation of CF and OGW, conversion of AA or GR into PA, and selecting adequate greenhouse covers could help to mitigate regional climate change.

The initial dilution generated by the final disposal of untreated wastewater through a submarine outfall in Santa Marta was examined with a near-field dilution model. Northward and eastward seawater velocity, salinity, and temperature profiles from a 3D hydrodynamic model were used to provide the oceanic conditions to calculate the dilution. At the wastewater discharge site, the upwelling phenomenon occurs two times a year, the major from December to March and the minor in July, eliminating the stratification condition of seawater. The results of the dilution model showed that in these periods the plume reaches the water surface achieving dilutions greater than 100. In addition, the external wave effect on the initial dilution of submarine outfall discharge in Santa Marta was determined. Surface waves increase dilution during the dry period of the year when trade winds increase the surge and start the upwelling phenomenon. The Dilution with/without waves factor is up to 1.90 for the center of the plume on the water column.

Coronavirus Disease-2019 (COVID-19) is an infectious disease caused by the Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2). There is sufficient experimental evidence to confirm that SARS-CoV-2 infection produces states of ciliary and flagellar dysfunction. However, these studies are unable to explain the observed effects molecularly, because they lack a sufficient understanding of the interaction between human proteins and virus proteins. Using the physical-chemical study of the human interactome in interaction with the SARS-CoV-2 proteome, we found evidence of interactions to explain the experimental effects from a molecular perspective. We found that ten viral proteins interact with key components in the maintenance of the molecular structure of axoneme. Additionally, we evaluated the pulmonary and extrapulmonary pathogenesis of COVID-19 from the point of view of ciliary dysfunction, and warned about other possible complications such as episodes of transient infertility that, due to the limitations of our work, would need verification.

This work presents an alternative to harnessing wind energy with an Electromagnetic Frequency Regulator (EFR) coupled to a hydrostatic transmission and associated with a horizontal axis wind turbine, a bidirectional frequency inverter and a secondary energy source, in a hybridized system. The hydrostatic transmision is composed by a fixed displacement axial piston pump and a variable displacement, swash plate, axial piston motor. Feedback linearization was used as a technique to control the motor geometric displacement, and a prediction algorithm for the steady state rotations of the armature and the electromagnetic field has been developed. A 5\,kW project was simulated on a Scilab platform, with combinations of constant or variable load, and constant or variable wind speed. The results indicated that the system was able to supply the generator load, adapting to fluctuations in wind speed. The possibility of storing wind energy through the inverter has also been proven. The system can accumulate energy in batteries during the fastest wind regimes, to use it when the turbine power is lower than the load.

Objectives: As institutions modified medical practices to mitigate the spread of the SARS-CoV-2 virus, providers were forced to modify care through the implementation of telemedicine. The objective of this article is to review the current practices of otolaryngology during the COVID-19 pandemic and the limitations of telemedicine in current practice. Methods: A thorough review of the PubMed and MEDLINE databases was performed for publications between 2020 and 2021. Studies discussing telemedicine in otolaryngology during COVID-19 pandemic were selected. Results: As worldwide cases of COVID-19 continue to oscillate, we must continue to be vigilant in our clinical practice, implementing safe techniques to mitigate the spread of the SARS-CoV-2 virus through the continual use of telemedicine in all specialties of otolaryngology. Trends of increased patient acceptance of the use of telemedicine have been seen across subspecialities, including otolaryngology. Conclusion: Currently there are challenges associated with the implementation of telemedicine in the field of otolaryngology that rely heavily on adjunct physical examination, imaging studies, and specialty procedures. However, telemedicine has tremendous potential and can be adapted to include in the otolaryngologist’s toolbelt during public health emergencies such as the COVID-19 pandemic.

Structural hydroxide groups in layered magnesium-aluminum double hydroxides were partially replaced by fluoride ions. Fluorinated and fluorine-free materials were used as hosts for two dyes, carminic acid and hydroxyl naphthol blue, resulting in a hybrid pigment color palette. Additionally, the pigments were protected with a magnesium hydroxide phase to prevent the color from fading over time. The color properties of the pigments were significantly influenced by the host of dye, since the presence of fluorine directly influences the acid-base properties of the layered double hydroxides. Finally, the pigments were successfully applied to prepare colored creams.

Manganese sludge, an industrial waste in the ferroalloy industry, contains various components and holds significant importance for sustainable development through its valorization. This study focuses on characterizing a manganese sludge and investigating its behavior during sulfuric acid leaching. The influence of process conditions, including temperature, acid concentration, liquid to solid ratio, and leaching duration, was examined. The results revealed that Mn, Zn, and K are the main leachable components, and their leaching rates increase with increasing temperature, liquid to solid ratio, and time. However, acid concentration requires optimization. High leaching rates of 90% for Mn, 90% for Zn, and 100% for K were achieved. Moreover, it was found that Pb in the sludge is converted to sulfate during the leaching which yields a sulfate concentrate rich in PbSO4. The leaching process for Mn and Zn species appears to follow a second or -third order reaction, and the calculation of rate constants indicated that Mn leaching kinetics are two to five times higher than those for Zn. Thermodynamic calculations were employed to evaluate the main chemical reactions occurring during leaching.

The Black population, often treated as ethnically homogenous, faces a constant challenge in accessing and utilizing healthcare services. This study examines the intragroup differences in health-seeking behavior among the multiple ethnic subgroups that comprise the Black community. A cross-sectional study was conducted among 239 adults ≥18 years who self-identified as Black in the United States and Canada. A multiple logistic regression model was fitted to evaluate the relationship between health-seeking behaviors and ethnic origin controlling for selected social and health related factors. The mean age of participants was 38.6 years, 31% were male, and 20% were unemployed. Sixty-one percent reported very good or excellent health status, and 59.7% reported not being treated for chronic disease at the time of the survey. Aging (OR=1.05, CI:1.01–1.09) and being female (OR= 0.30, CI: 0.14–0.65) were associated with favorable health-seeking behaviors. Compared with participants who had earned high school diplomas only, those who reported having earned graduate degrees were 75% less likely to have engaged in favorable health-seeking behavior (OR=0.25, 95% CI: 0.07–0.86). In the Black community of our sample, regardless of ethnic origins or country of birth, the factors associated with health-seeking behavior were age, gender, and educational attainment. Keywords: African American; African; Caribbean; Healthcare Utilization; Ethnic Disparities; Health-seeking behavior; intragroup difference, black populations, ethnic subgroups

The goal of the paper is to clarify the observed irrationality of decision making in conflict situations considered as one-step games of two players. To solve such situations, we consider the asymmetry in the relation of the players to their own rewards and the rewards of the opponents. Formalization of the decision-making process is based on recently developed non-commutative operators of multivalued logic algebra. The suggested method is applied to solve the well-known Prisoners’ dilemma game and the other situations of conflict, where it results in the expected strategies.

Savouring is an emotion regulation strategy and intervention that focuses on the process of attending, intensifying and prolonging positive experiences and positive affect associated with these memories. Personal savouring involves a reflection on positive memories that are specific to the individual and do not involve others. In contrast, relational savouring entails reflecting on instances when people were responsive to the needs of their significant others. Such interventions hold potential to benefit parents of children with autism spectrum disorder (ASD). Mothers of children with ASD tend to experience higher anxiety, lower positive affect (PA) and more negative affect (NA) compared to mothers of neurotypical children, leading to a diminished overall well-being. Moreover, ASD has multiplied by up to four times in the recent decade. Thus, this paper investigates whether savouring may enhance the overall well-being of mothers of young children with ASD by increasing positive affect and decreasing negative affect. 52 mothers of neurotypical children and 26 mothers of children with ASD aged 3-7 years old were given a series of questionnaires and randomly assigned to either relational savouring or personal savouring conditions. In relational savouring, mothers were asked to reflect upon a shared positive experience with their child while in the personal savouring condition, a personal positive experience was recalled. Across mothers of children with ASD and neurotypical children, findings suggest that savouring leads to a decrease in NA (p &lt; .01) but not increases in PA. Similarly, mothers with higher levels of anxiety experience a greater decrease in NA (p &lt; .001) compared to mothers with lower levels of anxiety post-savouring. This study proposes that a brief savouring intervention may be effective among mothers of preschoolers. As lower levels of negative affect is linked to healthier psychological well-being, mothers might be able to engage in more effective and warm parenting after savouring exercises, which would cultivate positive mother-child relationships that benefit their children in the long-term.

We studied the performance of a quantum magnetic Stirling cycle that uses a working substance composed of two entangled antiferromagnetic qubits (J) under the influence of an external magnetic field (Bz) and an uniaxial anisotropy field (K) along the total spin in the y-direction. The efficiency and work were calculated as a function of Bz and for different values of the anisotropy constant K given hot and cold reservoir temperatures. The anisotropy has been shown to extend the region of the external magnetic field in which the Stirling cycle is more efficient compared to the ideal case.

Philippines as an archipelago and tropical country, which is situated near the Pacific ocean, faces uncertain rainfall intensities. This makes environmental, agricultural and economic systems affected by precipitation difficult to manage. Time series analysis of Philippine rainfall pattern has been previously done, but there is no study investigating its probability distribution. Modeling the Philippine rainfall using probability distributions is essential, especially in managing risks and designing insurance products. Here, daily and cumulative rainfall data (January 1961 - August 2016) from 28 PAGASA weather stations are fitted to probability distributions. Moreover, the fitted distributions are examined for invariance under subsets of the rainfall data set. We observe that the Gamma distribution is a suitable fit for the daily up to the ten-day cumulative rainfall data. Our results can be used in agriculture, especially in forecasting claims in weather index-based insurance.

Gaucher Disease's (GD) pathophysiology generates anesthetic concerns in Total Hip joint Arthroplasty (THA), and due to its rareness, data on perioperative risks is scarce. This 22-year study at a large reference center addresses anesthetic management and perioperative outcomes in GD. This retrospective-cohort study assessed anesthetic success and safety in 30 THA patients, comparing them with a control-matched group. Data on clinical characteristics, perioperative events, and outcomes were collected. The primary outcome was difficult anesthesia-initiation incidence. Secondary outcomes were difficult intraoperative course and hemodynamic management, and the development of postoperative-complications. The age, sex, weight, body mass index, primary-to-revision hip arthroplasty ratio were similar in both groups. The mean age was 48±13 years. Ten arthroplasties were revision while twenty were primary. There was no significant difference at all-type anesthesia first initiation attempt success. No particular preference by staff anesthetists for general anesthesia or neuraxial procedures was observed. The GD group showed significantly higher mean intraoperative packed red blood cell units administered (0.73 vs 0.18);(p= 0.038)), higher intraoperative and postoperative platelet transfusion incidence (5/30 [16.7%] vs. 0/56 [0.00%];p=0.004) and (3/30 [10%] vs 0/56 [0%];p=0.040) and longer mean recovery-room length-of-stay (426±412 vs 175±140;p=0.004). Postoperative complications were not significantly different.

The aim was to assess the precision and accuracy of cephalometric analyses performed by artificial intelligence (AI) with and without human augmentation. Four dental professionals with varying experience levels and AI identified 31 landmarks on 30 cephalometric radiographs twice. These landmarks were re-identified by all examiners with the aid of AI. Precision and accuracy were assessed by using intraclass correlation coefficients (ICCs) and mean absolute errors (MAEs). AI revealed the highest precision with a mean ICC of 0.97, while the dental student had the lowest (mean ICC: 0.77). AI/human augmentation method significantly improved precision of the orthodontist, resident, dentist, and dental student by 3.26%, 2.17%, 19.75%, and 23.38%, respectively. The orthodontist demonstrated the highest accuracy with a MAE of 1.57 mm/˚. AI/human augmentation method improved the accuracy of the orthodontist, resident, dentist, and dental student by 12.74%, 19.10%, 35.69%, and 33.96%, respectively. AI demonstrated excellent precision and good accuracy in automated cephalometric analysis. The precision and accuracy of the examiners with the aid of AI improved by 10.47% and 27.27%, respectively. The AI/human augmentation method significantly improved the precision and accuracy of less experienced dental professionals to that of an experienced orthodontist.

The goal was to create a novel machine learning (ML) model which can predict the magnitude and direction of pubertal mandibular growth in males with Class II malocclusion. Lateral cephalometric radiographs of 123 males at three time points (T1: 12, T2: 14, T3: 16 years old) were collected from an online database of longitudinal growth studies. Each radiograph was traced, and 7 different ML models were trained using 38 data points obtained from 92 subjects. 31 subjects were used as a test group, to predict post-pubertal mandibular length and Y-axis using input data from T1 and T2 combined (2-year prediction), and T1 alone (4-year prediction). Mean absolute errors (MAEs) were used to evaluate the accuracy of each model. For all ML methods tested using the 2-year prediction, the MAEs for post-pubertal mandibular length ranged from 2.11-6.07mm and 0.85-2.74° for the Y-axis. For all ML methods tested with 4-year prediction, the MAEs for post-pubertal mandibular length ranged from 2.32-5.28 mm and 1.25-1.72° for the Y-axis. Besides its initial length, the most predictive factors for mandibular length were found to be chronological age, upper and lower face heights, upper and lower incisor positions and inclinations. For the Y-axis, the most predictive factors were found to be Y-axis at earlier time points, SN-MP, SN-Pog, SNB and SNA. Whilst the potential of ML techniques to accurately forecast future mandibular growth in Class II cases is promising, a requirement for more substantial sample sizes exists to further enhance the precision of these predictions.

Background and Objectives: Peanut allergy is the most common single cause of anaphylaxis in children. The risk factors for anaphylaxis in children with peanut allergy are not well defined. Therefore, we aimed to identify epidemiological, clinical and laboratory characteristics of children with peanut allergy that may predict the severity of allergic reaction and anaphylaxis. Materials and Methods: We conducted a cross-sectional study and included 94 children with peanut allergy. Allergy testing was performed, including skin prick testing and determination of specific IgE levels to peanut and its Ara h2 component. In case of discordance between patient history and allergy testing, an oral food challenge with peanut was performed. Results: Anaphylaxis, moderate and mild reactions to peanuts occurred in 33 (35.1%), 30 (31.9%) and 31 (33.0%) patients, respectively. The severity of the allergic reaction only weakly correlated (p = 0.04) with the amount of peanuts consumed. The median number of allergic reactions to peanut was 2 in children with anaphylaxis compared with 1 in other patients (p = 0.04). The median level of specific IgE to Ara h2 was 5.3 IU/ml in children with anaphylaxis compared to 0.6 IU/ml and 10.3 IU/ml in children with mild and moderate peanut allergy (p = 0.06). The optimal cutoff for distinguishing between anaphylaxis and a less severe allergic reaction to peanut was a specific IgE Ara h2 level of 0.92 IU/ml with 90% sensitivity and 47.5% specificity for predicting anaphylaxis (p = 0.04). Conclusions: Epidemiological and clinical characteristics of the patient cannot predict the severity of allergic reaction to peanut in children. Even standard allergy testing, including component diagnostics, is a relatively poor predictor of the severity of allergic reaction to peanuts. Therefore, more accurate predictive models including new diagnostic tools are needed to reduce the need for oral food challenge in most patients.

Background We intend to examine whether the COVID-19 outbreak influences medical decision-making (MDM) among Non-COVID patients. Method We recruit 287 patients who admit to ER department due to cardiovascular complaints. Anxiety level was measured using three questionnaires (GAD-7, Beck Inventory, and the cardiac anxiety questionnaire). A fourth survey was designed to assess MDM considerations. Results 64% of patients were male (median age 54). Almost half of the patients were found to have moderate to severe levels of anxiety.79.3% of patients reported that the outbreak influenced their MDM. 44.5% of patients sought medical care 2-3 from the onset of symptoms. Coronary artery disease was found in only 26 patients (9.1%). Almost half of the patients stated that they would have gone earlier if not for the current pandemic. Conclusion Non-COVID patients seeking medical care had a high anxiety level that directly affected decision-making and put them at unnecessary risk.

In the process of transcription initiation by RNA polymerase, promoter DNA sequences affect multiple reaction pathways determining the productivity of transcription. However, the question of how the molecular mechanism of transcription initiation depends on sequence properties of promoter DNA remains poorly understood. Here, combining the statistical mechanical approach with high-throughput sequencing results, we characterize abortive transcription and pausing during transcription initiation by Escherichia coli RNA polymerase at a genome-wide level. Our results suggest that initially transcribed sequences enriched with thymine bases represent the signal inducing abortive transcription. On the other hand, certain repetitive sequence elements broadly embedded in promoter regions constitute the signal inducing pausing. Both signals decrease the productivity of transcription initiation. Based on solution NMR and in vitro transcription measurements, we also suggest that repetitive sequence elements of promoter DNA modulate the rigidity of its double-stranded form, which profoundly influences the reaction coordinates of the productive initiation via pausing.

The COVID-19 pandemic caused by the SARS-CoV-2 virus has inflicted significant mortality and morbidity worldwide. Continuous virus mutations have led to the emergence of new variants. The Omicron BA.1 sub-lineage prevailed as the dominant variant globally at the beginning of 2022 but was subsequently replaced by BA.2 in numerous countries. Wastewater-based epidemiology (WBE) offers an efficient tool for capturing viral shedding from infected individuals, enabling early detection of potential pandemic outbreaks without relying solely on community cooperation and clinical testing resources. This study integrated RT-qPCR assays for detecting general SARS-CoV-2 and its variants levels in wastewater into a modified triple susceptible-infected-recovered-susceptible (SIRS) model. The emergence of the Omicron-BA.1 variant was observed, replacing the presence of its predecessor, the Delta variant. Comparative analysis between the wastewater data and the modified SIRS model effectively described the BA.1 and subsequent BA.2 waves, with the decline of the Delta variant aligning with its diminished presence below the detection threshold in wastewater. This study demonstrates the potential of WBE as a valuable tool for future pandemics. Furthermore, by analyzing the sensitivity of different variants to model parameters, we are able to deduce real-life values of cross-variant immunity probabilities, emphasizing the asymmetry in their strength.

The objective of this research was to study the dynamics of moisture and nutrition at the root zone and to quantify the variables linked to efficient water management in avocado orchards of mid and high-lands of Michoacán, México, in typical Andisols of low fertility with (A)C(w2) and C(w2) climates, respectively. Using the FDR (Frequency Domain Reflectometry) technology, the dynamics of soil moisture and salinity were recorded daily at four depths: 0-15, 15-30, 30-45, and 45-60 cm. The soil moisture balance model was used to determine actual evapotranspiration (ETr), crop coefficient (Kc), and water use efficiency (WUE). Results indicated that ETr is 66-73% of the total water at 0-30 cm depth; the fertilizer absorption is limited to 0-30 cm, being negligible at deeper layers. The water use efficiency is 4.4 to 5.6 kg of fruit m-3 of applied water, and the ratio of the water use index (ETr/irrigation sheet applied, ISA) is 0.65-0.70; while the annual avocado Kc is 0.72 in Cutzato and 0.78 in Tiamba. We concluded that avocado has a low water requirement, it does not cause leaching of nutrients and/or water, the absorption of water and nutrients mostly occurs at 30 cm depth, and from a hydrological point of view, the crop is environmentally friendly.

The use of antibiotics in neonatal units worldwide varies significantly. We included data from 2015-2022 from the EpicLatino database, which comprises a network of 32 units in Latin America and the Caribbean with gestational age at birth (GA) of ≤ 32 weeks. A questionnaire was sent to the EpicLatino units, to correlate practice with outcomes. Negative binomial regression with standard errors and confidence intervals computed for incidence-rate ratios (IRRs) was used for comparative statistics on antibiotic days per 1000 patient-days between units. All units that responded had 1-6 differences with the reference unit (Unit 2) with the best results, but there was no clear association with the IRR. Each EpicLatino unit should review its statistics to explore possibilities for reducing antibiotic usage.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

To support the decision making process of new investors, this paper aims to implement Machine Learning algorithms to generate investment indications. Three artificial intelligence techniques were implemented, namely: Multilayer Perceptron, Logistic Regression and Decision Tree, which performed the classification of investments. The results of the different algorithms were compared to each other using the metrics: accuracy, precision, recall, and F1-score. The Decision Tree was the algorithm that obtained the best classification metrics and an accuracy of 77%.

Digital transformation of agriculture can support economic growth and food and nutri-tion security in Africa. This study provides an overview of the status of digital agriculture in five west African countries, analyzing their efforts in developing the enabling environment and inno-vations while formulating recommendations based on the identified gaps for the effective trans-formation of the sector. Information was retrieved through a literature search from various sources, including web pages and databases of national agricultural and digital transformation institutions and start-ups of the five target countries (Benin, Burkina Faso, Côte d'Ivoire, Ghana, Nigeria) and regional/international institutions. There have been increasing agri-digital initia-tives in the five countries, which were grouped into seven categories based on their objectives. Steady progress was also observed in mobile internet adoption, despite the differences in deploy-ing crucial infrastructure to promote digital agriculture. The mobile connectivity index (MCI) in all five countries is below 60. Nonetheless, Ghana and Cote d'Ivoire demonstrated more efforts in internet and electricity access, especially in rural areas. Benin and Nigeria have developed sep-arate documents depicting the roadmap for Digital Agriculture, while the other countries are working to create one or have it embedded in their national development plans. Similarities and specificities exist among countries for laws and processes protecting Agri-digital innovators. To be competitive and self-reliant in the global e-economy, these countries must reposition them-selves to accelerate changes in digital agriculture through effective governance and synergy of actions in different sectors and across nations.

Dioscorea composita is a plant native to México and Central America with a high concentration of diosgenin precursors. Currently, México is one of the two most important countries producers of this yam; however, climate change is altering the environmental conditions of its natural habits, threatening its preservation and productivity. This is why this research was focused to characterize the eco-geography of D. composita and predict its potential geographic distribution under climate change scenarios in México-Central America. A collection of 408 geo-referenced accessions was used to determine its climatic adaptation, ecological descriptors, and the current and future potential geographic distribution, which was modeled with MaxEnt model through the Kuenm R-package. For future climate scenarios, an ensemble of the GCMs HadGEM-ES and CCSM4 was used. Results showed that D. composita adapts to warm humid and very humid agro-climates and that the most contributing variables for its presence are annual and seasonal moisture availability indices, seasonal photoperiod, annual thermal range, Bio14 and Bio11. The year 2050 RCP 4.5 climate scenario would contract the potential distribution of D. composita, whilst the 2050 RCP 8.5 scenario would expand it, indicating that this species could be a good crop option under this scenario of emissions.

Various distance metrics and their induced norms are employed in the quantitative modeling of evolutionary dynamics. Minimization of these distance metrics when applied to evolutionary optimization are hypothesized to result in different outcomes. Here, we apply the different distance metrics to the evolutionary trait dynamics brought about by the interaction between two competing species infected by parasites (exploiters). We present deterministic cases showing the distinctive selection outcomes under the Manhattan, Euclidean and Chebyshev norms. Specifically, we show how they differ in the time of convergence to the desired optima (e.g., no disease), and in the egalitarian sharing of carrying capacity between the competing species. However, when randomness is introduced to the population dynamics of parasites and to the trait dynamics of the competing species, the distinctive characteristics of the outcomes under the three norms become indistinguishable. Our results provide theoretical cases when evolutionary dynamics using different distance metrics exhibit similar outcomes.

In the current study, we assessed the effects of conventional and Ultra High Dose Rate (UHDR) irradiation on behavioral and cognitive performance one month following exposure and assessed whether these effects were associated with alterations in the number of immune cells in the hippocampus using flow cytometry. Conventional- and UHDR-irradiated mice showed impaired novel object recognition. During fear learning, conventional- and UHDR-irradiated mice moved less during the inter-stimulus-interval (ISI) and UHDR-irradiated mice also moved less during the baseline period (prior to the first tone). In irradiated mice, reduced activity levels were also seen in the home cage; conventional- and UHDR-irradiated mice moved less during the light period and UHDR-irradiated mice moved less during the dark period. Following behavioral and cognitive testing, infiltrating immune cells in the hippocampus were analyzed by flow cytometry. The percent Ly6G+ CD45+ cells in the hippocampus was lower in conventional- and UHDR-irradiated than sham-irradiated mice, suggesting that neutrophils might be particularly sensitive to radiation. The percent of Ly6G+ CD45+ cells in the hippocampus was positively correlated with the time spent exploring the novel object in the object recognition test, suggesting that the reduced percent Ly6G+ CD45+ cells in the hippocampus might mediate some of the detrimental radiation-induced cognitive effects.

Capsicum annuum var. glabriusculum, is a variety of wild chili pepper belonging to the family Solanaceae and is considered as the origin for all cultivated chili species of the world. This species is an important genetic resource for agriculture and food, is widely distributed in northeastern Mexico in altitudes from 0 – 1200 m.a.s.l. This species grows mainly at low altitudes and its upper limit reaches 1000m., it prefers temperatures above 18.3^O C and its production and harvest may ocurr at two seasons, one during the beginning of the summer and the main one ocurring in the middle of the autumn in northeast México. It is estimated that the main production occurs in the state of Tamaulipas with 84 tons per year and is harvested from 23 municipalities. Concentration of capseicins and dihydrocapsaicine from wild populations may vary considerably from one location to another in the municipalities, ecotypes and diverse climatic conditions from this wide geographic zone. The high demands of wild chili as well as the variability on concentration of capseicins in fruits are considered as some of the main reasons why intensive cultivation of this species should be carried out in Northeastern Mexico.

Dioscorea remotiflora, a perennial climbing herbaceous plant wild and native to México, bears tubers of important ethnobotanical and nutritional value. However, the information for its production and use is precarious. The objective of this research was to characterize the adaptation habitats of D. remotiflora in order to determine its ecological descriptors and current distribution, as well as to model its potential distribution. A comprehensive database encompassing 481 geo-referenced accessions was assembled. Using the Agroclimatic Information System for México and Central America (SIAMEXCA), 42 environmental variables were formulated. The MaxEnt model within the Kuenm R-package was employed to predict the species distribution. The findings reveal a greater presence of D. remotiflora in harsh environments, characterized by arid to semi-arid conditions, poor soils, and hot climates with long dry periods. The plant's nutritional and medicinal attributes, combined with its ecological adaptability, suggest its viability within evolving regional cropping systems under the influence of climate change. Niche modeling revealed that seven key variables determine the geographical distribution of D. remotiflora: precipitation of the warmest quarter, precipitation of the driest month, minimum temperature of the coldest month, November-April solar radiation, annual mean relative humidity, annual moisture availability index, and May-October mean temperature. Favorable regions for D. remotiflora coincide with its current presence sites, while other suitable areas, such as the Yucatan Peninsula, Northeast region, and Gulf of México, offer potential expansion opportunities for the species distribution. The characterization obtained for D. remotiflora, together with the description of its edaphic and climatic adaptation habitats, will enable an efficient design of strategies for its use and conservation in the near future.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x104 – 2x107 CFU per ml and has a sensitivity of S = 1.655x105 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10-9 grams (g) which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Regeneration of lost tail is of great importance to lizards. Anolis carolinensis, a green lizard, is capable of regenerating its tail efficiently after autotomy. Hence, it is considered as a model organism in regeneration study. A. carolinensis shed its tail in order to distract the predator’s attention and thus makes a way to escape. Restoring of the amputated tail takes several days and the mechanism is currently clearly understood. Although save its life, tail regeneration is associated with the impairment of several vital functions in Anoles. In addition, various differences have been observed between original and regenerated tail in terms of mechanism and structure. To date, very little work has been conducted on tail autotomy and regeneration at molecular and genetic level. The genes responsible for regeneration in anoles are identified recently. These genes are evolutionarily conserved through all tetrapod vertebrates. They are, however, in a state of ‘switched-off’ in other vertebrates including humans. Consequently, a throughout study of these so called ‘switched-off’ genes may provide a way of restoring lost organs in human, and thus could revolutionize the modern medical science.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.