In the present work, the effects of ageing treatment on the microstructures of a near-β Ti alloy (TC18) are studied. The influence of ageing treatment on the tensile properties and failure mechanisms are systematically analyzed. It is found that the size and morphology of the primary α (αp) phases are insensitive to ageing temperature and time. Furthermore, the ageing temperature and time dramatically influence the precipitation of the secondary α (αs) phases. Massive αs phases precipitate and gradually coarsen, and finally weave together with increasing the ageing temperature or extending the ageing time. The thickness of αs phases is responsible for the material strengths, while the content of α phases can enhance the material ductility. The ductile characteristics of the alloy with coarser αs phases are more obvious than those with thinner αs phases. Therefore, the ageing treatment is helpful for the precipitation and homogeneous distribution of αs phases, which is essential for balancing the strengths and ductility of the studied Ti alloy.

With the development of hyperspectral technology, to establish an effective spectral data compressive reconstruction method that can improving data storage, transmission and maintaining spectral information is critical for quantitative remote sensing research and application in vegetation. By introducing the idea of compressive sensing in compressed reconstruction, the spectral adaptive grouping distributed compressive sensing algorithm is proposed, which enables a distributed compressed sensing reconstruction of plant hyperspectral data. The experimental results showed that comparing with orthogonal matching pursuit(OMP) and gradient projection reconstruction(GPSR), the proposed algorithm can significantly improve the visual effect of image reconstruction in the spatial domain. The PSNR in low sampling rate(sampling rate is lower than 0.2) increases by 13.72dB than OMP and 1.66dB than GPSR. In the spectral domain, the average normalized root mean square error、the mean absolute percentage error and the mean absolute error of the proposed algorithm is35.38%，31.83% and 33.33% lower than GPSR respectively.. Therefore, the proposed algorithm can achieve relatively high reconstructed efficiency.

This paper investigates a distributed, coordinated motion control network based on multiple direct-drive, linear switched reluctance machines (LSRMs). A hierarchical, two-level synchronization control strategy is proposed for the four LSRMs based motion control network. The high-level, reference signals agreement algorithm is first employed to correct the asynchronous behaviors of the position commands. Then, the low-level tracking synchronization method is applied for the collaborative position control of the four LSRMs. The proposed two-level, fault-tolerant control strategy eliminates the asynchrony of the reference signals and it also guarantees the coordinated tracking control performance of the four LSRMs. Experimental results demonstrate that effective coordinated tracking control can be ensured, based on successful agreement of reference signals and an absolute tracking error falling within 2 mm can be achieved.

Landslide is one of the most common geological disasters in China, which is characterized by suddenness and uncertainty, and it is difficult to realize accurate identification, early warning and forecasting of landslide disaster by conventional means. With the development of high-resolution remote sensing satellites and InSAR surface deformation monitoring technology, the traditional means of landslide monitoring data sources are limited, and there is a lack of effective methods to excavate the characteristics of the spatial distribution of landslide hazards and their triggering factors and other issues. In this paper, the area extending 10 km outside the VII isobar of the Gengma earthquake is taken as the study area, and 13 evaluation factors are screened out by integrating the factors of InSAR surface deformation, topography and geological environment, and the Bayesian Optimized Convolutional Neural Network (BO-CNN) is used for the evaluation of landslide susceptibility, and the BO-RF and PSO-SVM models are selected for the comparative analysis. The model accuracy evaluation was carried out by three indexes: ROC curve, AUC value and FR value, in which the ROC curves of PSO-SVM, BO-RF and BO-CNN were all close to the upper-left corner of the corner, and the AUC values were 0.9388, 0.9529, and 0.9535, respectively, and the FR value of landslide in the high susceptibility area of BO-CNN was as high as 14.9, and was higher than that of PSO-SVM and BO-RF, respectively. SVM and BO-RF model is 4.55 and 3.69 higher, the experimental results show that the BO-CNN model used in this paper has a better effect in landslide susceptibility evaluation, and the research results of the local government's disaster prevention and mitigation measures are of great significance.

This paper discusses about control of the linear switched reluctance machines (LSRMs) network for the zero phase-difference tracking to a sinusoidal reference. The dynamics of each LSRM is derived by online system identification and modeled as a second-order linear system. Accordingly, based on the coupled harmonic oscillators synchronization manner, a distributed control is proposed to synchronize each LSRM state to a virtual LSRM node representing the external sinusoidal reference for tracking it with zero phase-difference. Subsequently, a simulation scenario and an experimental platform with the identical parameter setup are designed to investigate the tracking performance of the LSRMs network constructed by the proposed distributed control. Finally, the simulation and experimental results verify the effectiveness of the proposed LSRMs network controller, and also prove that the coupled harmonic oscillators synchronization method can improve the synchronization tracking performance and precision.

The regenerated magnesia-calcium brick samples that had added 0, 1.5, 3.0 wt.% aluminium oxide (Al2O3) were prepared by using spent magnesia-calcium bricks, fused magnesia and Al2O3 powder additive as the main raw materials. The phases, microstructures, room temperature and hot flexural strength, resistance to cement clinker corrosion and strength of coating adherence were investigated respectively. It indicated that the addition of Al2O3 increased mainly resulting in the content of tetracalcium aluminoferrite (C4AF) and tricalcium aluminate (C3A) increased in the regenerate samples. The bulk density, the room temperature flexural strength and the strength of coating adherence all increased, while the hot flexural strength and corrosion resistance both deteriorated along with the increase of Al2O3 addition. It was because that on the one hand the low melting point phases of C4AF and C3A improved the sinterability of the regenerated samples during the burning stage, on the other hand they melted or existed in liquid phase during the experimental temperature (1573 K and 1823 K) which degraded hot flexural strength and corrosion resistance, and enhanced the strength of coating adherence as the wettability of the liquid phase. The content of Al2O3 in the regenerated magnesia-calcium brick should not be higher than 1.1 wt.%, considering its room and high-temperature performances for cement rotary kiln.

SARS-CoV-2, the newly identified human coronavirus causing severe pneumonia epidemic, was probably originated from Chinese horseshoe bats. However, direct transmission of the virus from bats to humans is unlikely due to lack of direct contact, implying the existence of unknown intermediate hosts. Angiotensin converting enzyme 2 (ACE2) is the receptor of SARS-CoV-2, but only ACE2s of certain species can be utilized by SARS-CoV-2. Here, we evaluated and ranked the receptor-utilizing capability of ACE2s from various species by phylogenetic clustering and sequence alignment with the currently known ACE2s utilized by SARS-CoV-2, predicting potential intermediate hosts of SARS-CoV-2.

In nature and engineering applications, flexible fiber beds covering biological surfaces can play a role in reducing resistance. These fibers deform under the action of fluids, and this deformation affects the fluid flow state, forming a complex fluid-solid interaction phenomenon. To quantitatively analyze such issues, the physical model is simplified to the deformation problem of an soft hair bed caused by Stokes flow, and the deformation problem of a single fiber caused by Stokes flow is further studied. The deformation problem of an elastic single fiber in a channel caused by Stokes flow can be described by a nonlinear integral equation. We have obtained a new series solution, which has been compared with the previous perturbation method to verify the accuracy and effectiveness of the series solution. Meanwhile, we have further provided an extended form of flexible fiber deformation through experimental fitting. This fluid-solid interaction problem involves multiple fields and is very important in many natural and engineering systems. The research in this paper can not only help us better understand complex phenomena in nature but also delve into the interaction mechanism between fluids and solids, providing a theoretical basis for future scientific research and engineering applications.

Biotic and abiotic factors influence the formation of fungal-algal pairings in lichen symbiosis. It is poorly known which factors determine the specific associations, especially when distantly related fungi are considered. Here, we investigated the effect of different drivers on the association patterns of taxonomically diverse lichenized fungi and their trebouxioid symbiotic partners. In 200 samples collected across three biomes, we found 41 species of lichenized fungi, associating with 16 species of trebouxioid green algae, of which 62% were previously unreported. Species identity of the fungal and algal partner had the greatest effect on the outcome of the symbiosis compared with abiotic factors such as climatic variables and geographic distance. Partner specificity was found to be higher in tropical regions than in temperate and arctic regions. Co-phylogenetic analyses indicated congruent phylogenies of trebouxioid algae and associated fungi, rejecting their random associations. Evolutionary mechanisms contributing most to the observed phylogenetic patterns were ‘loss’ and ‘failure to diverge’ of the algal partners. This study broadens our knowledge of fungi-algae symbiotic patterns in view of Trebouxia-associated fungi.

Resistive patch array incorporating with metallic backplane provided an effective way to the achievement of broadband metamaterial absorbers(MAs). When loading metallic metamaterial to resistive MA, the outstanding construction helps realize more flexible and diversified forms of broadband absorption. In this paper, we attempted to load metallic resonators(MRs) to resistive MA in the three-dimensional construction, which benefits further enhancement of lower-frequency absorption. Simulation showed that the partial absorption band was separated to lower frequency, while the rest of broadband absorption was unaffected. Meanwhile, after combining multi-unit of the proposed MAs, the stair-stepping broadband absorption was also achieved. At last, three samples were fabricated. The agreements between simulations and experimental results demonstrated that resistive MA loaded with MRs provided an effective way for further enhancement of lower-frequency absorption with almost no change of the absorbing structure and areal density. Thus, it is worthy to expect a wide range of applications to emerge inspired from the proposed attempt.

In cosmology, the cosmic curvature $K$ and the cosmological constant $\Lambda$ are two most important parameters, whose values have strong influence on the behavior of the universe. By analyzing the energy-momentum tensor and equations of state of ideal gas, scalar, spinor and vector potential in detail, we find that the total mass density of all matter is always positive, and the initial total pressure is negative. Under these conditions, by qualitatively analyzing the global behavior of the dynamical equation of cosmological model, we get the following results: (i) $K= 1$, namely, the global spatial structure of the universe should be a 3-dimensional sphere $S^3$. (ii) $0\le\Lambda < 10 ^ {-24} {\rm ly} ^ {-2}$, the cosmological constant should be zero or an infinitesimal. (iii) $a(t)>0$, the initial singularity of the universe is unreachable, and the evolution of universe should be cyclic in time. This means that the initial Big Bang is impossible at all. Since the matter components considered are quite complete and the proof is very elementary and strict, these logical conclusions should be quite reliable. Obviously, these conclusions will be much helpful to correct some popular misconceptions and bring great convenience to further research other problems in cosmology such as property of dark matter and dark energy.

The description of the microscopic world in quantum mechanics is very different from that in classical physics, and there are some points of view that are contrary to intuition and logic. The first is the loss of reality, the behavior of micro particles shows randomness and hopping. The second is the loss of certainty, the conjugate physical variables of a system cannot be determined synchronously, they satisfy the Heisenberg uncertainty principle. The third is the non-local correlation. The measurement of one particle in the quantum entanglement pair will change the state of the other entangled particle simultaneously. In this paper, some concepts related to quantum entanglement, such as EPR correlation, quantum entanglement correlation function, Bell's inequality and so on, are analyzed in detail. Analysis shows that the mystery and confusion in quantum theory may be caused by the logical problems in its basic framework. Bell's inequality is only a mathematical theorem, but its physical meaning is actually unclear. The Bell state of quantum entangled pair may not satisfy the dynamic equation of quantum theory, so it cannot describe the true state of microscopic particles. In this paper, the correct correlation functions of spin entanglement pair and photonic entanglement pair are strictly derived according to normal logic. Quantum theory is a more fundamental theory than classical mechanics, and they are not parallel relation in logic. However, there are still some unreasonable contents in the framework of quantum theory, which need to be improved. In order to disclose the real relationship between quantum theory and classical mechanics, we propose some experiments which show the wave-particle duality simultaneously and provide intuitionistic teaching materials for the new interpretation of quantum theory.

The magnetic field of the earth plays an important role in the ecosystem, and the magnetic field of celestial bodies is also important in the formation of cosmic large-scale structures, but the origin and evolution of the celestial magnetic field is still an unresolved mystery. Many hypotheses to explain the origin have been proposed, but there are some insurmountable difficulties for each one. At present, the theory widely accepted in scientific society is the dynamo model, it says that, the movement of magnetofluid inside celestial bodies, which can overcome the Ohmic dissipative effect and generate persistent weak electric current and macroscopic magnetic field. However, this model needs an initial seed magnetic field, and the true values of many physical parameters inside the celestial body are difficult to obtain, and there is no stable solution to the large range of fluid motion. These are all difficulties for the dynamo model. Furthermore, it is difficult for the dynamo to explain the correlation between the dipole magnetic field and angular momentum of a celestial body. In this paper, by calculating the interaction between spin of particles and gravity of celestial body according to Clifford algebra, we find that a rotational celestial body provides a field $\Omega^\alpha$ for spins, which is similar to the magnetic field of a dipole, and the spins of charged particles within the celestial body are arranged along the flux line of $\Omega^\alpha$, then a macroscopic magnetic field is induced. The calculation shows that the strength of $\Omega^\alpha$ is proportional to the angular momentum of the celestial body, which explains the correlation between the magnetic intensity and angular momentum. The results of this paper suggest that further study of the effects of internal variables such as density, velocity, pressure and temperature of a celestial body on $\Omega^\alpha$ may provide some new insights into the origin and evolution of celestial magnetic field.

Type 2 diabetes mellitus (T2DM), a multifactorial and complicated metabolic disorder, is a growing public health problems. Numerous studies indicated that bioactive compounds from herbal medicine have beneficial effects on T2DM prevention and treatment, owing to their numerous biological properties. Curcumin, the major curcuminoid of turmeric, is one of the most studied bioactive components of herbal supplements, which has a variety of biological activities. Clinical trials and preclinical research have recently produced compelling data to demonstrate the crucial functions of curcumin against T2DM via several routes. Accordingly, this review systematically summarizes the antidiabetic activity of curcumin, along with various mechanisms. Results showed that effectiveness of curcumin on T2DM is due to it being anti-inflammatory, anti-oxidant, anti-hyperglycemic, anti-apoptotic, anti-hyperlipidemia and other activities. In light of these results, curcumin may be a promising prevention/treatment choice for T2DM.

Relationships of the three bryophyte lineages (liverworts, mosses, and hornworts) to vascular plants is a pivotal question in the study of origin and evolution of land plants. In recent decades, this question has been subject to intense phylogenetic analyses using morphological characters, multigene DNA sequences, and genome structural characters. A tentative consensus reached ten years ago suggested that bryophytes are a paraphyletic group, with liverworts being sister to all other land plants and hornworts being sister to vascular plants. However, several more recent nuclear phylogenomic studies have concluded that bryophytes represent a monophyletic group that is sister to vascular plants. A discussion is presented here on strengths and weaknesses of different types of characters (morphological traits, nucleotide sequences, and genome structural arrangements), and their suitability for resolving deep phylogenetic relationships. Moreover, several criteria for credible phylogenetic reconstruction are proposed. Strong statistical support for reconstructed relationships should be derived from high quality, independent characters selected for suitability to the particular question being addressed. The relationships inferred in a study should be congruent with those from as many other lines of phylogenetic evidence as possible. Any incongruities should be explicable by well-understood biological mechanisms. It is concluded that the relationships of the three bryophyte lineages to vascular plants should currently be viewed as unresolved. This is a difficult phylogenetic problem; the land plants underwent a rapid radiation a long time ago. Yet, further exploration of analytical methods and careful choice of characters should lead to eventual elucidation of diversification patterns among early land plants.

The precise prediction of air contaminant dispersion is essential to the air quality monitoring and the emergency management of the contaminant gases leakage incidents in the chemical industry park. The conventional atmospheric dispersion models can seldom give precise prediction due to inaccurate input parameters. In order to improve the prediction accuracy of dispersion model, two data assimilation methods (i.e. one is merely based on the typical particle filter while the other is a combination of particle filter and expectation-maximization algorithm) are proposed to assimilate the UAV observations into the atmospheric dispersion model. Two emission cases are taken into consideration, the difference between which is the different dimensions of state variables. To test the performances of the proposed methods, experiments corresponding to the two emission cases are designed and implemented. The results show that the particle filter can effectively estimate the model parameters and improve the accuracy of model prediction when the dimension of state variables is low. In contrast, when the dimension of state variables becomes higher, the method of particle filter combining expectation-maximization algorithm performs better in the parameter estimation accuracy and warm-up time. Therefore, the data assimilation methods are able to effectively support the air quality monitoring and emergency management in chemical industry parks.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

Based on the Expected Utility Theory and Regret Theory, the Extended Regret Theory (ERT) is proposed in this paper to study the optimal pricing strategy of retailers in e-commerce environment. Taking the diversity of sales channels and the uncertainty of consumers in e-commerce environment into consideration, author of the paper designs an extended regret utility function which comprehensively considers both pessimistic and optimistic attitudes of decision makers in retailing industry to describe their regret-avoidance behavior. According to the sensitivity analysis, it is found that the optimal retail price decreases as the consumer price sensitivity coefficient increases, yet does not show variation with changes of the consumers pessimism degree. Moreover, the optimal retail price(s) obtained under EUT, ERT and combination of EUT and ERT represent the same.

Purpose: The purpose of this study is to further explore how e-loyalty and E-marketing influences E-trust and satisfy the demand by offering fresh perspectives based on research as well as emphasis on the factors influencing the E-trust such as culture as a mediator. This study not only contributed theoretically but also presented practical implementations. Design/methodology/approach: Online survey was used to obtain data by focusing the Hospitality sector (Hotel Industry) and verifying the conceptual framework. Data was collected in multiple time lags. Findings: Findings showed that the E-trust influenced by E-loyalty and E-Marketing. E-trust comes from the previous experiences, e-loyalty and e-marketing. Further, some trends such as culture influenced the e-trust. Research limitation/implications: The present study is quite suitable for those Researchers interested in learning more about the effects of E-loyalty and E-marketing on user E-trust and how to mitigate cultural influences can benefit from the current study. This research also has implications for those who wish to improve market allure and survival in digital world. This study focused on the hospitality sector (Hotel Industry) in China; however, the sector and geography could be altered to suit the needs of the study's participants. Practical implications: The present study delivers the practical guidelines which are quiet suitable for understanding the formation of E-loyalty, E-marketing, and E-trust through which specific E-marketing strategy can be designed to deal with the consumer’s E-loyalty and their expectations as per their Cultural perspective. At some particular regions/countries, cultural trends are more important than practical market. This research study practically showed that how culture changed the consumer set of mind. Originality/value: The relationship between E-loyalty, E-marketing, E-trust, specifically with the cultural influence in digital market has been the subject of few research.

The identification of spatiotemporal heterogeneity, its key determinants, and the interaction effects between the driving factors of urban resilience (UR) within and between subregions is fundamental for understanding its underlying mechanisms. A resilience evaluation model was applied to analyze the temporal and spatial differences in UR in Hunan Province, China. The standard deviation ellipse was used to explore the spatial and dynamic evolution and direction of UR. A hot spot analysis identified clusters of cold and hot spots. The contribution of spatiotemporal differences in UR within and between subregions was assessed using the Theil index. A geodetector analysis determined the factors influencing UR and their interactions. There was an increasing trend in UR from 0.2692 in 2014 to 0.3422 in 2022. The number of cities with high resilience gradually increased from 2014 to 2022, while there was a decreasing gradient in UR from northeast to southwest across the province. High-resilience cities had positive spillover effects on the surrounding area. Hot spots were predominantly located in the northeast, while cold spots were concentrated in the southwest. The barycenter of UR shifted from northeast to southwest by 2018, before moving southeast by 2022. The Theil index values declined over time both within and between subregions. Per capita GDP, average wages of on-the-job employees, per capita social consumption, and doctor density enhanced UR. Two-factor interactions had a greater influence on the spatiotemporal heterogeneity of UR than single factors. Two-factor and nonlinear enhancements were identified as the primary mode of influence.

The interaction between spinors and gravity is the most complicated and subtle interaction in the universe, which involves the basic problem to unified quantum theory and general relativity. By means of Clifford Algebra, a unified language and tool to describe the rules of nature, this paper systematically discusses the dynamics and properties of spinor fields in curved space-time, such as the decomposition of the spinor connection, the classical approximation of Dirac equation, the energy momentum tensor of spinors and so on. To split spinor connection into Keller connection $\Upsilon_\mu\in\Lambda^1$ and pseudo-vector potential $\Omega_\mu\in\Lambda^3$ by Clifford algebra not only makes the calculation simpler, but also highlights their different physical meanings. The representation of the new spinor connection is dependent only on the metric, but not on the Dirac matrix. Keller connection only corresponds to geometric calculations, but the potential $\Omega_\mu$ has dynamical effects, which couples with the spin of a spinor and may be the origin of the celestial magnetic field. Only in the new form of connection can we clearly define the classical concepts for the spinor field and then derive its complete classical dynamics, that is, Newton's second law of particles. To study the interaction between space-time and fermion, we need an explicit form of the energy-momentum tensor of spinor fields. However, the energy-momentum tensor is closely related to the tetrad, and the tetrad cannot be uniquely determined by the metric. This uncertainty increases the difficulty of deriving rigorous expression. In this paper, through a specific representation of tetrad, we derive the concrete energy-momentum tensor and its classical approximation. In the derivation of energy-momentum tensor, we obtain a spinor coefficient table $S^{\mu\nu}_{ab}$, which plays an important role in the interaction between spinor and gravity. From this paper we find that, Clifford algebra has irreplaceable advantages in the study of geometry and physics.

Clifford algebra is unified language and efficient tool for geometry and physics. In this paper, we introduce this algebra to derive the integrable conditions for Dirac and Pauli equations. This algebra shows the standard operation procedure and deep insights into the structure of the equations. Usually, the integrable condition is related to the special symmetry of transformation group, which involves some advanced mathematical tools and its availability is limited. In this paper, the integrable conditions are only regarded as algebraic conditions. The commutators expressed by Clifford algebra have a neat and covariant form, which are naturally valid in curvilinear coordinate system and curved space-time. For Pauli and Schr\"odinger equation, many solutions in axisymmetric potential and magnetic field are also integrable. We get the scalar eigen equation in dipole magnetic field. By the virtue of Clifford algebra, the physical researches may be greatly promoted.

In this note we construct explicit complex and real matrix representations for the generators of real Clifford algebra $C\ell_{p,q}$. The representation is based on Pauli matrices and has an elegant structure similar to the fractal geometry. We find two classes of representation, the normal representation and exceptional one. The normal representation is a large class of representation which can only be expanded into $4m+1$ dimension, but the exceptional representation can be expanded as generators of the next period. In the cases $p+q=4m$, the representation is unique in equivalent sense. These results are helpful for both theoretical analysis and practical calculation. The generators of Clifford algebra are the faithful basis of $p+q$ dimensional Minkowski space-time or Riemann space, and Clifford algebra converts the complicated relations in geometry into simple and concise algebraic operations, so the Riemann geometry expressed in Clifford algebra will be much simple and clear.

Most fully developed galaxies have vivid spiral structure, but the formation and evolution of spiral structure is still a mystery that is not fully understood in astrophysics. We find that the currently used equations of galactic dynamics contain some unreasonable components. In this paper, the following three working assumptions are introduced to simplify the galactic structural equations. 1. In the research of large-scale structure, the retarded potential of the gravitational field should be taken into account. The propagating time of the gravitational field from center to border is longer than the revolution periods of the stars near the center of galaxy. Newton's gravitational potential is unreasonable for such case, and the weak field and low velocity approximation of Einstein's field equation should be adopted. 2. The stars in a fully developed galaxy should be zero-pressure and inviscid fluid, and the equation of motion is different from that of ordinary continuum mechanics. Stars move along geodesics. 3. The structure of the galaxy is only related to the total mass density distribution. The equation of state of dark halo is different from that of ordinary luminous interstellar matter, so their trajectories are also very different. Dark halo and ordinary matter in galaxy are automatically separated. The total mass density distribution can be presupposed according to the observation data, and then it can be determined by comparing the solution of the equations with the observed data. These assumptions and treatments are supported by theory and observation. The variables of the equations of simplified galactic dynamics are separated from each other, and the equations are well-posed and can be solved according to a definite procedure. Therefore, this simplified dynamic equation system provides a more reasonable and practical framework for the further study of galactic structure, and can solve many practical problems. Besides, it is closely related to the study of dark energy and dark matter.

In this paper, we provide some enlightening examples of the application of Clifford algebra in geometry, which show the concise representation, simple calculation and profound insight of this algebra. The definition of Clifford algebra implies geometric concepts such as vector, length, angle, area and volume, and unifies the calculus of scalar, spinor, vector and tensor, so that it is able to naturally describe all variables and calculus in geometry and physics. Clifford algebra unifies and generalizes real number, complex, quaternion and vector algebra, converts complicated relations and operations into intuitive matrix algebra independent of coordinate systems. By localizing the basis or frame of space-time and introducing differential and connection operators, Clifford algebra also contains Riemann geometry. Clifford algebra provides a unified, standard, elegant and open language and tools for numerous complicated mathematical and physical theories. Clifford algebra calculus is an arithmetic-like operation that can be well understood by everyone. This feature is very useful for teaching purposes, and popularizing Clifford algebra in high schools and universities will greatly improve the efficiency of students to learn fundamental knowledge of mathematics and physics. So Clifford algebra can be expected to complete a new big synthesis of scientific knowledge.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

The shear stress generated by wall turbulence is the main cause of wall friction resistance in turbulent flow through pipes. This paper investigates the impact of inserting rest periods (regions of constant Reynolds number) within the pulsating operating cycle of velocity on the fully turbulent flow at large time-averaged Reynolds numbers, using the Large Eddy Simulation (LES) method. The study aims to explore the effect of increasing rest periods within pulsations on drag resistance. The dimensionless shear stress and drag reduction rates during different time periods of rest were analyzed. Numerical simulation results indicate that the pulsating velocity operation mode does not necessarily lead to drag reduction; it may even result in increased resistance. Inserting rest periods within the pulsation cycle can achieve drag reduction effects, with the maximum drag reduction rate reaching 21.8\%. Comparisons with experimental data and Direct Numerical Simulation (DNS) from the literature validate the feasibility of using the LES method for pipe pulsating operation modes.

People have always hoped to be able to fill an entire plane with ``single unit cells'' without periodicity. This wish was realized after the mathematician discovered a 13-sided ``single unit cell'' named `einstein'. These non-periodic tessellations generally exhibit anisotropic properties, making them superior in terms of mechanical performance compared to periodic structures. From the perspective of information entropy, the reason behind the improved mechanical properties of these structures is the higher entropy associated with non-periodic configurations. To quantify the disorder of non-periodic structures, we propose an entropy expression for the `einstein' metamaterial. To demonstrate the mechanical properties of these high-entropy structures, we fabricate specimens using 3D printing and conducte mechanical experiments. For comparative analysis, we also use ABAQUS to perform finite element analysis of the problem. The research results reveal that the mechanical properties of high-entropy structures created by the non-periodic stacking of cells are significantly improved compared to those of low-entropy structures created by periodic stacking. The conclusions drawn from the study of individual issues are generalizable and may be of assistance in future material and structural design.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

(1) Background: AI technology has been deeply applied to online shopping platform to provide more accurate and personalized services for consumers. It is of great significance to study the different functional experience of AI for consumers to improve the current application status of AI technology.(2)Method: Based on the "S-O-R" model, this study divided the AI technology expe-rienced by the consumers of online shopping platform into accuracy, insight and interaction experience. Takes the perceived value as the mediating variable from the prospect of perceived utility value and perceived hedonic value. This article use empirical research method to analyze the effect of three dimensions of online shopping AI experience to research the internal influence mechanism of consumers purchase intention. (3) Results:① The accuracy, insight and interaction experience of AI marketing technology have a significant positive impact on consumers' per-ceived utility value and hedonic value respectively; ②Both of the perceived utility value and perceived hedonic value obtained by AI technology experience can promote the formation of consumers' purchase intention; ③ The perceived hedonic value was better than perceived utility value to promote the consumers' purchase intention; ④The results of multi group analysis show that some younger and less experiences consumers groups prefer the pleasure experience such as shopping desire stimulation, shopping process relaxation and pleasure that AI marketing brought. However, utilitarian value cannot promote this kind of consumers' purchase intention. (4) Con-clusions: Perceived utility value and perceived hedonic value can be the intermediary between AI technology and consumers' purchase intention.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

This study introduces a novel predictive model for atomization droplet size, developed through comprehensive data collected under elevated temperature and pressure conditions using a twin swirl airblast nozzle. The model, grounded in flow instability theory, has been meticulously parameterized using the Particle Swarm Optimization (PSO) algorithm. Through rigorous analysis, including analysis of variance (ANOVA), the model has demonstrated robust reliability and precision, with a maximum relative error of 19.3% and an average relative error of 6.8%. Compared to the classical atomization model by Rizkalla and Lefebvre, this model leverages theoretical insights and incorporates a range of interacting variables, enhancing its applicability and accuracy. Spearman correlation analysis reveals that air pressure and the air pressure drop ratio significantly negatively impact droplet size, whereas the fuel-air ratio (FAR) shows a positive correlation. Experimental validation at ambient conditions shows that the model is applicable with a reliability threshold of ≥0.13 and highlight the predominance of the pressure swirl mechanism over aerodynamic atomization at higher fuel flow rates (q > 1.25 kg/h). This research effectively bridges theoretical and practical perspectives, offering critical insights for the optimization of airblast nozzle design.

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

(1) Background: in the context of sustainable development goals (SDGs), this work explores the repair direction of future cultivated land protection policies based on the Smith policy implementation model from the historical evolution to ensure that the cultivated land protection policy does not deviate during the implementation process. (2) Methods: this paper uses literature research and inductive deduction methods to sort out the evolution process of Chinese cultivated land protection policy, summarize the successful experience of transferring the focus of cultivated land protection in chronological order, and conclude the repair direction of Chinese cultivated land protection. (3) Results: although the Chinese cultivated land protection policy in the historical evolution has through three significant phases, there are still certain issues in the development trend of Chinese cultivated land protection policy based on regional division of labor for grain transportation and sales. (4) Conclusion: directly utilizing feedback from farmers as stakeholders will contribute to the maturity and improvement of cultivated land protection policies in the specific implementation of cultivated land protection policies.

A Weyl semimetal is a novel crystal with low-energy electronic excitations that behave as Weyl fermions. It has received worldwide interest and was believed to have opened the next era of condensed matter physics after graphene and three-dimensional topological insulators. Howev-er, it is not easy to obtain a single large-size crystal because there are many nucleations in the preparation process. Here, a bottom-seed CVT growth method is proposed in this paper, and we acquired the large-size, high-quality NbAs single crystals up to 5x4x4 mm3 finally. X-ray diffrac-tion and STEM confirmed that they are tetragonal NbAs, which the key is to use seed crystal in vertical growth furnace. Notably, the photoelectric properties of the crystal are obtained under the existing conditions, which paves the way for the follow-up work.

Limoncella of Mattinata, a rare and ancient Mediterranean citrus fruit, was investigated by sequence analysis of the ribosomal internal transcribed spacer regions, which assigns it as a variety of Citrus medica L. Morphological, chemical, and biomolecular approaches were used to characterize flavedo and albedo, parts usually rich of bioactive compounds. The morphological findings showed albedo and flavedo cellular structures as “reservoirs” of nutritional components. Both albedo and flavedo hydroalcoholic extracts were rich in polyphenols, but they were different in compounds and quantity. The flavedo is rich in p-coumaric acid and rutin, whereas the albedo contains high levels of hesperidin and quercitrin. Antioxidant, anti-inflammatory, and genoprotective effects for albedo and flavedo were found. The results confirmed the health properties of flavedo and highlighted that albedo is also a rich source of antioxidants. Moreover, this study valorizes Limoncella of Mattinata's nutritional properties, cueing its crops' repopulation.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

Uterine leiomyosarcoma (LMS) is a rare and aggressive form of uterine cancer, with a poor prognosis and high number of uterine cancer-related deaths. Chimeric Antigen Receptor (CAR) T-cell therapy is an immunotherapy approach to antigen specific of cancer cell, thereby enhancing the immune system's ability to target and destroy cancer cells. This study aims to investigate the potential of targeting differentially expressed genes (DEGs) as a novel therapeutic strategy using CAR T-cell technology in LMS. Genome datasets were obtained from NCBI-GEO database, Of the five datasets, genes that experienced significant overexpression in at least three datasets were categorized as DEGs, and DEGs were evaluated for protein localization, Gene Ontology, bioactivity, interaction, and overexpression. The results identified 25 DEGs, with ten of them expressed on the plasma membrane; four of them—HMMR, KIF20A, PRC1, and ZWINT—were part of the main protein network derived from the 25 DEGs. The dominant bioactivity of these PMGs involves influencing the cell cycle, particularly processes related to chromosome segregation. In conclusion, HMMR, KIF20A, PRC1, and ZWINT are high-potential DEGs as candidates for tumor-associated antigen CAR T-cell therapy. Further research, both in vitro and in vivo, is needed to enhance the validity of these findings.

Tengchongite is a uranyl molybdate uranium mineral and it was found and named by Chen 1985.No more scholars studied on tengchongite after Chen’s work, The identification of this mineral has only been confirmed by single crystal X-ray diffraction. In the paper, micro laser Raman spectroscopy and infrared spectroscopy are used to identify the spectroscopy properties of tengchongite. The studies fill in the gaps of more than 30 years in terms of the molecular spectroscopy research of tengchongite. The mineral has an ideal model of Ca(UO₂)₆(MoO₄)₂O₅•12H₂O its bands attributed to the vibrating units are clearly identified in the Raman spectrum. Symmetric stretching modes at 812 cm^-1 and 839 cm^-1 are assigned to ν1 (UO₂)²⁺ ,The ν3 antisymmetric stretching modes of (UO₂)²⁺ are observed at 896 cm^-1, Symmetric stretching modes at 419^-1 and 440 cm^-1 are assigned to ν2 (UO₂)²⁺ .Symmetric stretching modes at 919cm-1 are assigned to ν1(MoO₄)^2-,The ν3 antisymmetric stretching modes of (MoO₄)^2- are observed at 752 cm^-1, the in-plane ν2(MoO₄)^2-and the out-of-plane ν4(MoO₄)^2- bending modes are at 169 cm^-1 and 254 cm^-1. IR spectrum of tengchongite shows the major uranyl band at 858 cm^-1 and 693 cm^-1, Mo-O bonds are observed at about 985 cm^-1 and 780 cm^-1, and H₂O groups are present with a wide range peaks from 3100 cm^-1 to 3500 cm^-1 and 1647 cm^-1, and the band at 1432.4 cm^-1 is probably due to the stretching vibration hydroxyl (OH^-1), therefore, tengchongite contains may include hydroxyl and its chemical formula needs to be modified .

The chemical industry is an integral part of the world economy and a substantial income source for developing countries. However, existing regulations or the enforcement of these regulations, on controlling atmospheric pollutants sometimes may be insufficient, leading to the deterioration of surrounding ecosystems and to a quality decrease of the atmospheric environment. Previous works in this domain fail to generate executable solutions for inspection agencies due to practical challenges. In addressing these challenges, we introduce a so-called Chemical Plant Environment Protection Game (CPEP) to generate reasonable schedules of high-accuracy air quality monitoring stations for inspection agencies. First, Stackelberg Security Games (SSGs) are incorporated together with source estimation methods into this research. Second, high-accuracy air quality monitoring stations as well as gas sensors are modeled into the CPEP. Third, simplified data analysis on the regularly discharging of chemical plants is utilized to construct the CPEP. Finally, an illustrative case study is used to investigate the effectiveness of the CPEP Game, and a realistic case study is conducted to illustrate how the models and algorithms being proposed in this paper, work. Results show that playing a CPEP Game can reduce operational costs of high-accuracy air quality monitoring stations; moreover, playing the game leads to more compliance from the chemical plants towards the inspection agencies.

The calculation of echo intensity involved in the SAR image simulation is usually based on the electromagnetic formula or approximate formula derived under certain assumptions. However, the parameters used in these formulas are often difficult to obtain, and the formulas have errors with the actual situation. In this paper, a method of embedding deep neural network (DNN) into the simulation process based on ray tracing is proposed, so that the DNN model can be directly used to fit the calculation formula of echo intensity from real SAR images. Simulation results show that this method can obtain SAR images with high similarity.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

Considering the spectrum shortage problem of IoT devices, we introduce a collaborative spectrum sensing (CSS) framework in this paper to identify available spectrum resources, so that IoT devices can access it and meanwhile avoid causing harmful interference to the normal communication of the primary user (PU). However, in the process of the PU’s signal detection in IoT devices, the issue about the stopping time and decision cost arises. To this end, we propose a distributed cognitive IoT model, which includes two IoT devices independently using sequential decision rules to detect the PU. On this basis, we define the stopping time and cost function for IoT devices, and formulate an average cost optimization problem in CSS. To solve this problem, we further regard the optimal stopping time problem as a finite horizon problem, and solve the threshold of the optimal decision rule by dynamic programming. At last, numerical simulation results demonstrate the correctness of our proposal in terms of the global false alarm and miss detection probability, and it always achieves minimal average cost under various cost of each observation taken and thresholds.

Two-dimensional (2D) transition metal dichalcogenides (TMDCs) draw much attention as critical semiconductor materials for 2D, optoelectronic, and spin electronic devices. Although controlled doping of 2D semiconductors can also be used to tune their bandgap and type of carrier and further change their electronic, optical, and catalytic properties, it remains an ongoing challenge. Here, we successfully doped a series of metal elements (including Hf, Zr, Gd, Dy) into the monolayers MoS2 through a single-step chemical vapor transport (CVT), and the atomic embedded structure is confirmed by scanning transmission electron microscope (STEM) with a probe corrector measurement. In addition, the host crystal is well preserved, and no random atomic aggregation is observed. More importantly, adjusting the band structure of MoS2 enhanced fluorescence and carrier effect. This work provides a growth method for doping nonlike elements into 2D MoS2 and potentially many other 2D materials to modify their properties.

Using the 2011-2020 digital inclusive finance data released by Peking University and the index system constructed by the Blue Book of China Rural Revitalization and Development Index (2018), this paper analyzes the dynamic evolution of the digital inclusive finance and the rural revitaliza-tion from time and space dimensions with the help of kernel density estimation, Markov chain and Moran index. Using The Gini coefficient decomposition method to analyze the source of differ-ences in digital inclusive finance, and then using the spatial autoregressive (SAR) model and ge-ographically weighted regression (GWR) model to study the boosting effect of digital inclusive finance on rural revitalization from the perspective of spatial aggregation and spatial differentia-tion, respectively. The results show that: (1) The growth rate of China's digital inclusive finance slows down year by year, and the inter-provincial differences increase year by year and show gradient characteristics, indicating that there may be a trend of multipolar differentiation. The overall level of Rural Revitalization shows an increasing trend, and the gap between provinces is still apparent. (2) The evolution of digital inclusive finance and rural revitalization is a slow ad-justment process, and there has been no cross-level jump in the past ten years. In digital inclusive finance, the liquidity from the highest and lowest levels to the medium level is high. However, the liquidity in the states of rural revitalization development level is not high. (3) Rural revitalization has a positive spatial spillover effect. The level of rural revitalization in the western area is signif-icantly lower than in the eastern area. At the same time, there is no significant difference between the east and central areas. The depth of the use of digital inclusive finance has a significant positive impact on the revitalization and development of rural areas, indicating that the further promotion of digital inclusive finance business in rural areas can substantially boost the revitalization of rural areas. (4) The boosting effect of digital inclusive finance on rural revitalization shows prominent spatial differentiation characteristics. The depth of use and the degree of digitization generally show a positive impact. The central and eastern coastal cities have the highest impact, decreasing toward the southwest and northeast. The areas with the lowest usage depth impact are clustered in the northeast, and the areas with the lowest digitization impact are clustered in the southwest.

Frequently Asked Questions (FAQs) systems rely on semantic symmetry similarity measuring between two sentences. To address the challenges of insufficient training data and limited domain-specific understanding in low-resource FAQs, this paper proposes a general framework, PDAMF-FAQ, to solve these issues. Firstly, we propose a paraphrasing-based data augmentation model that integrates syntactic information and edit vectors. Using a rule-based approach, it retrieves template sentences from a corpus and masks relevant words with special characters. Edit vectors between the original and paraphrase sentences are added to a pre-trained model's encoding layer to enhance the model's ability to learn the differences between the original and reference paraphrase sentences. Additionally, this paper presents a mixed-feature semantic matching model based on SimBERT. The model extracts keyword features from the text, replacing these keywords with special characters to construct intent features. These intent features, along with the user question and keyword features, are then concatenated to form the model's input. Experiments were conducted respectively on the paraphrasing-based data augmentation model, mixed-feature semantic matching model and their comprehensive application in a low-resource domain-specific FAQ. The experimental results show that the proposed framework effectively improve the performance of domain-specific FAQ system.

Abstract: Chloroplast is a new hotspot in the field of plant transformation system of plant genetic engineering. Initially developed in Chlamydomonas and tobacco, it is now feasible in a broad range of species. They exploit the homologous recombination and segregation pathways acting on chloroplast genomes and are based on direct repeats, transient co-integration or co-transformation and segregation of trait and marker genes. Foreign site-specific recombinases and their target sites provide an alternative and effective method for removing marker genes from plastids.Chloroplast genetic engineering has many advantages over nuclear genetic enginering, especially site-specific introduction of foreign genes ,leading to the absence of gene siliency and positon effect,which providing the available to explore the regulation and mechanism of chloroplast genes`expression in vitro .It also can identify the structure and function of the chloroplast genome , the expression of chloroplast affect the nulear genome. In this paper, the basic methodology of chloroplast transformation, the current techniques and applications, and the future possibilities for Chloroplast genetic engineering was reviewed[1-3].

Over the few decades, cancer-associated mortalities and morbidities were continuously increased worldwide despite sophisticated technological advancements. Pharmaceutical interventions associated with drugs exhibit a high degree of side effects and toxicities in addition to very high costs. Subsequently, to reduce or to vanish the side effects and high costs, researchers are now exploring natural bioactive compounds such as quercetin in its nanoformulations along with biologics as cargo delivery vehicles. Quercetin along with mesenchymal stromal lineage-derived extracellular vesicles (EVs) possesses an anti-cancer potential that can be explored to treat hepatocellular carcinoma (HCC). Exerting enhanced effect, nano quercetin synergistically with EVs triggers the anti-cancer mechanisms by regulating and dysregulating several signalling mechanisms including NF-κB, p53, JAK/STAT, MAPK, Wnt/β-catenin and PI3K/AKT, in addition to PBX3/ERK1/2/CDK2, and miRNAs modulation. In addition, findings regarding the potential checkpoints of anti-cancer signalling pathways were investigated that offer opportunities to develop engineered EVs incorporated with nano quercetin for the development of novel therapeutics to treat HCC in future. In this present mechanistic review, we abridged the regulation of such signalling mechanisms synergetic approach of nano quercetin and EVs. The regulatory role of EVs in the manifestation of innumerable miRNAs has also been tailed with special context to HCC.

Porous tantalum (Ta) is a promising biomaterial and has been applied in orthopedics and dentistry for nearly two decades. The high porosity and interconnected pore structure of porous Ta promise fine bone ingrowth and new bone formation within the inner space, which further guarantee rapid osteointegration and bone-implant stability in long term. Porous Ta has high wettability and surface energy that can facilitate adherence, proliferation and mineralization of osteoblasts. Meanwhile, low elastic modulus and high friction coefficient of porous Ta can effectively avoid stress shield effect, minimize marginal bone loss and ensure primary stability. Accordingly, the satisfactory clinical application of porous Ta based implants or prostheses are mainly derived from its excellent biological and mechanical properties. With the advent of additive manufacturing, personalized porous Ta based implants or prostheses have shown their clinical value in the treatment of individual patient who need specially designed implant or prosthesis. In addition, many modification methods have been introduced to enhance the bioactivity and antibacterial property of porous Ta with promising in vitro and in vivo research results. In any case, choosing suitable patients is of great importance to guarantee surgical success after porous Ta insertion.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

Spirit of science is one of the important components of science education theory. It not only directly affects the level of science education, but also indirectly affects the selection, education and evaluation of scientific researchers, and the development of science and technology in a country or region. Although more than a century ago, the researchers began to discuss the topic of spirit of science. However, to date, the research of the definition, attribute, structural model and its characteristics of the spirit of science has not yet made a breakthrough. Based on the detailed literature review, the related theoretical analysis and the research of the structural model of the spirit of science, this paper puts forward the new definition, the attribute and the establishment of the structural model of the spirit of science, and analyzes the match the situation from new structural model of the spirit of science and the scientific nature published by the American Society for the Advancement of Science. The results of this study are of great significance for raising the level of scientific education and cultivating future scientific researchers, enhancing their motivation and skills in innovation in scientific research and promoting the development of future scientific undertakings.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

Objectives: This study aimed to analyze the awareness of local residents regarding healthcare projects and to suggest some ideas for the revision of local ones. Methods: To delve into the opinions of local residents, the author of this study created a questionnaire composed of eight questions on the general characteristics of the respondents, eight questions on satisfaction with health centers, 16 questions on the awareness of healthcare projects, and 22 questions on local healthcare. The survey was conducted for 409 residents who visited public centers in Gimcheon from 15 March to 14 April 2021. Results: Data analysis revealed the following: The proportion of local residents who use health centers was 39.1%, and those users visit health centers, on average, 3.92 times a year. Among healthcare projects, the project known by the highest proportion of people was vaccinations (84.5%), which was also the project that was most used (38.1%). Among healthcare projects needed in the with-COVID-19 age, respondents awarded the highest score to vaccinations (4.15 points on a five-point Likert scale) and the second highest score to infectious disease management (4.12). Conclusions: For healthcare projects, central and local governments should focus on activating vaccinations, solving the problem of medical accessibility through untact remote treatment and establishing national infectious disease-specializing hospitals and local infectious disease management based on such national hospitals.

Background: Despite advances in the treatment of hepatocellular carcinoma (HCC) over the last few decades, treatment opportunities for patients with HCC remain limited. HCC is the most common form of liver cancer, accounting for approximately 90% of all cases worldwide. Moreover, apart from the current pharmacological interventions, hepatic resection and liver transplantation are the mainstay curative approaches for patients with HCC. Methods: This systematic review included phase I, II, III, and IV clinical trials (CTs) and randomized controlled trials (RCTs) on current treatments for patients with HCC in an Asian population (2013–2023). A total of 427 articles were screened, and 184 non-duplicate publications were identified. After screening titles and abstracts, 96 publications were excluded, and another 28 were excluded after full-text screening. The remaining 60 eligible RCTs/CTs were finally included. Results: Sixty clinical trials fulfilled our inclusion criteria and screened 36 drugs as monotherapy or combination therapy for HCC. Most studies used sorafenib alone or in combination with any of the treatment regimens. Lenvatinib or atezolizumab with bevacizumab was used for HCC after initial sorafenib treatment. Eighteen studies compared the efficacy of sorafenib with that of other drugs, including lenvatinib, cabozantinib, tepotinib, tigatuzumab, linifanib, erlotinib, resminostat, brivanib, tislelizumab, selumetinib, and refametinib. Conclusion: This study provides comprehensive insights into effective treatment interventions for HCC in Asian populations. The overall assessment indicated that sorafenib alone or in combination with atezolizumab and bevacizumab has been the first treatment choice in the past decade to achieve better outcomes in patients with HCC in an Asian population

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

Avian influenza viruses (AIVs) are highly contagious respiratory viruses of birds, lead-ing to significant morbidity and mortality globally and causing substantial economic losses to the poultry industry. Since their first isolation in 2013, the Asian-origin H5N1 highly pathogenic avian influenza viruses (HPAI) of clade 2.3.4.4b have undergone unprecedented evolution and re-assortment of internal gene segments and have spread to Asia, Europe, Africa, and America, caus-ing outbreaks in all the poultry categories. Novel epidemiological and pathobiological character-istics, distinct from other clades, are specific of clade 2.3.4.4b viruses. Wild waterfowl, the natu-ral reservoir of AIVs, are frequently found infected with clade 2.3.4.4b viruses, which can also cause high morbidity and mortality in these birds. The sustained clade 2.3.4.4b virus circulation in waterfowl has also led to virus infection in other wild bird species, with implications for the conservation of endangered species. Furthermore, clade 2.3.4.4b viruses have been isolated in var-ious wild and domestic mammals worldwide, and critical mutations related to virus adaptation to mammalian species have been identified, raising concerns about virus spillover to humans. The main clinical signs, and anatomopathological findings associated to clade 2.3.4.4b virus infection in birds and non-human mammals are hereby summarized.

Changes in coastal topography can affect the ecological environment and marine industries. In this study, we analyzed the patterns and causes of changes in shoreline and undersea topography in the Nakdong River estuary in the southeast of South Korea using depth and shoreline surveys of the estuary, as well as data on discharge, suspended sediments, and precipitation in the Nakdong River basin. The results showed that erosion and sedimentation occurred repeatedly owing to complex factors such as the discharge of the estuary and invasion by open sea waves. However, no clear unilateral trend was observed. Unlike previous survey data, a large amount of erosion occurred in the second half of 2020. Previously, sedimentation was the main process, but erosion occurred rapidly, which was observed in the summer of 2020 when the erosion was three times higher than that in other periods owing to the severe rainy season and torrential rains for over a month. In addition, regarding the flow rate and force of the river water outflow, the amount of discharge increased rapidly, causing erosion. Moreover, a strong typhoon in the summer of 2020 affected the topography of the estuary.

Concatemeric viral DNA is packaged into Bacteriophage P22 procapsids via a headful packaging mechanism mediated by a molecular machine consisting of small (gp3) and large (gp2) terminase subunits. Although a negative stain reconstruction exists for the terminase holoenzyme, it is not clear how this complex binds dodecameric portal protein located at a 5-fold mismatch vertex. Herein, we describe new assemblies for the holoenzyme. Both native mass spectrometry and transmission electron microscopy reveal that the P22 terminase complex adopts three main assemblies, which include a nonameric S-terminase bound to two L-terminase 1(gp3)9:2(gp2), two nonameric S-terminase bound to five L-terminase 2(gp3)9:5(gp2), and three nonameric S-terminase bound to seven L-terminase 3(gp3)9:7(gp2). Native agarose gel electrophoresis shows that the terminase complex interacts with procapsid with mild crosslinking. These results herein illustrate the P22 terminase complex can adopt a variety of confirmations and assembly states.

The decline in Pinus sylvestris var. mongolica in the introduction area has had a high profile in recent years. For the ecological restoration, management and silvicultural design of Mongolian pines in the introduction area, it is necessary to conduct a comprehensive and in-depth study on the ecological adaptation mechanism of Mongolian pines in provenances. The ecological process of water and nutrient accumulation as well as the influence of environmental factors on the photosynthetic physiology are the key to revealing the ecological adaptation mechanism of Mongolian pines. According to the differences of climate in the distribution area of Mongolian pines, sampling sites were set up, the effects of environmental factors on leaf δ13C and the relationship between leaf δ13C and nutrient content were analyzed. The results showed that leaf δ13C values were ranging from - 29.7 ‰ to - 23.76 ‰. The ecological stoichiometry, including LC (522.81 mg·g-1), LN (16.04 mg·g-1), LP (1.19 mg·g-1) and L-N:P (13.56), indicated that leaf photosynthesis and water use efficiency is greatly affected by environmental conditions, Mongolian pines had strong ability of carbon fixation, and its growth was obviously restricted by nitrogen. Although there was no significant correlation between δ13C with stoichiometric parameters in leaf, photosynthesis was the key link in the process of carbon fixation. It also showed that Pinus sylvestris var. mongolica was a stomatal limited plant. Leaf δ13C had significant correlation with climatic factors. VPD is the dynamic factor affecting the photosynthetic physiological process in leaves. Air and soil moisture are the dominate factors affecting the leaf stomatal conductance and determines leaf δ13C value, while other factors indirectly affect leaf δ13C by its impact on relative humidity or soil water content. Soil phosphorus content affected by clay is a key factor affecting soil water availability and soil nutrient cycling. Photosynthetic process in leaf is the dynamic process affecting the nutrient accumulation.

Parental phubbing behavior is a significant factor in predicting adolescent smartphone dependence, but prior research has predominantly focused on a unidirectional perspective from the child's viewpoint, overlooking potential perceptual differences between parents and their children regarding parental phubbing. Therefore, are there differences in the perceptions of parental phubbing between parents and their children? Based on the "Discrepancy-Maladaptive" hypothesis, the presence of perceptual discrepancies in family factors can lead to adverse developmental outcomes in children. Does the parent-child perceptual discrepancy in parental phubbing influence adolescent smartphone dependence? And what role does parent-child relationship play in this context? This study selected 728 families from a middle school in Wuhan, and surveys were administered to both children and parents. The findings reveal: (1) There exist significant parent-child perceptual discrepancies in parental phubbing. (2) Parent-child perceptual discrepancies in parental phubbing significantly positively predict adolescent smartphone dependence and negatively predict parent-child relationships, while parent-child relationships significantly negatively predict adolescent smartphone dependence. (3) The parent-child relationship plays a mediating role between parent-child perceptual differences in parental phubbing behavior and adolescent smartphone dependence.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

As the rapid development of communication industry, especially the 5G communication and IOT, there will be plenty of electromagnetic (EM) waves in the free space, which carry lots of energies. However, some of these energies are wasted in free space. To reuse these wasted energies, significantly growing interests are towards to the energy harvesting antennas. This paper is aimed to investigate a wearable antenna which can transfer RF energy from ambient sources to direct current by a soft and portable textile antenna. Among the numerous signals in mobile network, the GSM 1800, 3G, WiFi and 4G/5G will be chosen due to the city signal intensity distribution. Hence, a corresponding triple bands antenna has been designed to cover those frequency bands. The CST STUDIO SUITE is used in whole process of antenna design and simulation. The proposed antenna is a hooked dipole antenna with tuning bar (HATB) whose ends have small folded part in each side for better bandwidth performance. The presented antenna provides a wide operating band from 1.8 GHz to 2.5 GHz below -10 dB in return loss. And methods to overcome interference between antennas is found. Furthermore, using the corresponding rectifier to achieve the RF/DC conversion. The overall efficiency of whole rectifier is about 56.8 %, and output power level of the antenna system is 45.92nW. The experimental results could indicate that my textile hooked antenna harvester is a good choice for the charging system of personal wearable attachment, which could achieve low power absorbing for long distance anytime and anywhere.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

In this paper, polyurethane concrete (PUC) is used as wire embedding material to form a new polyurethane concrete- prestressed steel wire (PUC-PSW) reinforcement method. The lightweight and high-strength PUC materials not only bond and anchor the prestressed steel wire (PSW), but also passively participate in the structural force. The problems caused by using mortar or composite mortar as the embedding material are avoided. Twelve reinforced concrete T-beams were tested for PUC-PSW flexural reinforcement. It consists of 1 unreinforced beam, 4 PSW reinforced beams, and 7 PUC-PSW reinforced beams. The wire embedding material, wire anchorage form, PUC material depth, amount of wire, and loading type were used as variables. The test results show that PUC-PSW reinforcement can obviously enhance the flexural load and ultimate load of the reinforced beams compared with PSW reinforcement. The ability of PUC-PSW reinforcement to limit crack development is better than that of PSW reinforcement beam, especially after the main beam steel yield. The strength, stiffness and crack limiting ability of the reinforced beam increase with the PUC thickness of the reinforced layer.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Global food security for the increasing world population not only requires increased sustainable production of food but a significant reduction in pre- and post-harvest waste. The timing of when a fruit is harvested is critical for reducing waste along the supply chain and increasing fruit quality for consumers. The early in field assessment of fruit ripeness and prediction of the harvest date and yield by non-destructive technologies have the potential to revolutionize farming practices and enable the consumer to eat the tastiest and freshest fruit possible. A variety of non-destructive techniques have been applied to estimate the ripeness or maturity but not all of them are applicable for in situ (field or glasshouse) assessment. This review focuses on the non-destructive methods which are promising, or have already been, applied to the pre-harvest in field measurement including colorimetry, visible imaging, spectroscopy and spectroscopic imaging. Machine learning and regression models used in assessing ripeness are also discussed.

Fusarium head blight (FHB) disease is extensively distributed worldwide. This disease damages grain quality and reduces yield. The detection of this disease in a high throughput way is crucial to planters and breeders. Our study focused on developing a method for processing wheat color images and accurately detecting disease areas using deep learning and image processing techniques. The color images of wheat at the milky stage were collected and processed to construct datasets, which were used to retrain a deep convolutional neural network model using transfer learning. Testing results showed that the model can detect spikes, and the coefficient of determination of the number of spikes between the manual count and the detection was 0.80. The model was assessed, and the mean average precision for the testing dataset was 0.9201. On the basis of the results of spike detection, a new color feature was applied to obtain the gray image of each spike. Then, a modified region growing algorithm was implemented to segment and detect the diseased areas of each spike. Results show that the region growing algorithm performs better than K-means and Otsu’s method in segmenting the FHB disease. Overall, this study demonstrates that deep learning techniques enable the accurate detection of FHB in wheat using color images, and the proposed method can effectively detect spikes and diseased areas, thereby improving the efficiency of FHB detection.

As an emerging discipline, Design Morphology, with the advantage of "Form Study", has been integrated with many disciplines, and gradually formed its collaborative innovation paradigm. The inclusion of "Ecology" into Design Morphology is expected to promote the research of Design Morphology with the help of the systematic thinking and methods of ecology. The ecosystem of Design Morphology includes the natural ecosystem and the quasi-ecosystem closely related to human beings, and also put forward the concept of "Form Community" for the first time in the design field. In fact, this is exactly the research scope of Design Morphology. Advocating the ecological view of Design Morphology, can not only help to design researchers improve their values and world view, with new thinking and method to engage in "Form Study", but also contribute to the theoretical construction and thinking expansion of Design Morphology, and play a positive role in promoting interdisciplinary collaborative innovation led by Design Morphology. In addition, it can be used to evaluate the overall research and future development trend of Design Morphology, and provide the new research ideas and approaches for the development of design.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

The digital revolution has significantly impacted many Chinese Time-Honored businesses, particularly those slow to adapt to environmental changes, resulting in challenges related to long-term marketing capabilities and declining performance. This study explores the relationship between ambidextrous marketing capabilities and corporate performance. Utilizing a survey involving 91.8% of middle and upper-level managers across 47 Chinese time-honored firms, we construct a research model that demonstrates how the application of ambidextrous marketing capabilities can foster the development of Sustainable marketing capability, which in turn positively influence corporate performance. Sustainable marketing capability mediate the effect of ambidextrous marketing capabilities on corporate performance. Additionally, enhancements in market conditions or legislation may further amplify the impact of Sustainable marketing capability on business performance. In the context of Chinese time-honored firms, these findings offer managerial insights into building Sustainable marketing capability, enhancing performance, and achieving competitive advantages.

Gravity-aided inertial navigation system (GAINS) is an important development in autonomous underwater vehicle (AUV) navigation. An effective path planning algorithm plays an important role in the performance of navigation in long-term underwater missions. By combining the gravity information obtained at each position with the error information from the INS, the posterior Cram\'er-Rao bound (PCRB) of GAINS is derived in this paper. The PCRB is the estimated lower bound of position variance for navigation along the planned trajectory. And the sum of PCRB is used as the minimum cost from the initial state to the current state in the state space, and the position error prediction variance of inertial navigation system (INS) is used as the minimum estimated cost of the path from the current state to the goal state in the A* algorithm. Thus, a path planning method with optimal navigation accuracy is proposed. According to simulation results, traveling along the path planed by the proposed method can rapidly improve the positioning accuracy while consuming just slightly more distance. Even when measuring noise changes, the planned path can still maintain optimal positioning accuracy, and high positioning accuracy is possible for any trajectory located within a certain range of the planned path.

Sentinel-2 can provide multi-spectral optical remote sensing images in RGBN bands with a spatial resolution of 10m, but the spatial details provided are not enough for many applications. WorldView can provide HR multi-spectral images less than 2m, but it is a commercial paid resource with relatively high usage costs. In this paper, without any available reference images, Sentinel-2 images at 10m resolution are improved to a resolution of 2.5m through super-resolution (SR) based on deep learning technology. Our model, named DKN-SR-GAN, uses degradation kernel estimation and noise injection to construct a dataset of near-natural low-high-resolution (LHR) image pairs, with only low-resolution (LR) images and no high-resolution (HR) prior information. DKN-SR-GAN uses the Generative Adversarial Networks (GAN) combined of ESRGAN-type generator, PatchGAN-type discriminator and the VGG-19-type feature extractor, using perceptual loss to optimize the network, so as to obtain SR images with clearer details and better perceptual effects. Experiments demonstrate that in the quantitative comparison of the non-reference image quality assessment (NR-IQA) metrics like NIQE, BRISQUE and PIQE, as well as the intuitive visual effects of the generated images, compared with state-of-the-art models such as EDSR8-RGB, RCAN and RS-ESRGAN, our proposed model has obvious advantages.

Unmanned surface vehicles have the advantages of maneuverability, concealment, wide activity area and low cost of use. Therefore, they have broad application prospects. This makes unmanned surface vehicles a research hotspot at home and abroad, and the sensing technology is the basis for the unmanned surface vehicles to perform tasks. The perception technology based on optical vision has the advantages of convenient application, relatively low cost, easy data acquisition and large amount of information, and has been widely studied by scholars at home and abroad. This paper mainly discusses the research of optical vision in unmanned surface vehicles from five aspects: Firstly, the water surface image preprocessing based on unmanned surface vehicles, mainly including water surface image stabilization research and defogging enhancement research; two water boundary detection; It is the use of light vision target detection; the fourth is the surface target tracking method. Finally, the light vision research of unmanned surface vehicles is summarized and forecasted.

Landslide is a sliding movement of rock mass, debris and soil along the slope under the action of gravity. Small Baseline Subset (SBAS) is an established method for the investigation and monitoring of landslide moments. This study focuses on monitoring the long-temporal displacement of mountainous terrain in Danba County, Sichuan Province via SBAS technique, based on 31 scenes of L-band ALOS/PALSAR data from Feb. 2007 to Oct. 2010.The results show that the largest velocity rates in LOS direction are ±120 mm/yr and maximum accumulated displacement is up to -300, which indicates fast movement of the mountainous terrain during the observation time. These results get good consistency against the results of previous study. This demonstrates the strong potential of SBAS technique for monitoring the landslides geohazard.

Many agricultural water uses crowd the river ecology of the river water, thus leading to irreversible habitat damage. This paper presents an agricultural economic loss calculation model that is based on river ecological basic flow (REBF) protection by introducing a typical crop water requirement coefficient. First, the water balance equation is used according to a set of REBF protection values to compute the agricultural water shortage that results in the REBF. Second, the agricultural water shortage that results in REBF protection and a typical crop water requirement coefficient are used to determine the food production generated by REBF protection. Finally, the loss of food production and the food market prices are used to determine the agricultural economic loss caused by the different protection levels of REBF. A case study of the Weihe River in China is conducted. The calculation model is used to compute the agricultural economic loss on the basis of REBF protection in the Baoji section of the Weihe River, and the change law of the agricultural economic loss that results in different levels of the REBF is discussed. In addition, changes in the canal water use coefficient and the crop structure that affect agricultural economic loss are analyzed. Results show that the spatial and temporal variations in the runoff affect the changes in time and space of the agricultural economic loss. The higher the REBF protection level, the higher the agricultural economic loss. In addition, agricultural economic loss can provide a quantitative basis for reasonable REBF protection. The size of agricultural economic loss helps the government sector in decision-making on REBF protection.

Many biological functions of curcumin have been reported. As certain bioactivities of curcumin are eliminated by antioxidants, reactive oxygen species generated by curcumin have been suggested as a relevant mechanism. In the present study, effects of different types of antioxidants on stability and bioactivities of curcumin were analyzed. High concentrations (>4mM) of the thiol antioxidants including N-acetylcysteine (NAC), glutathione (GSH) and β-mercaptoethanol accelerated decomposition of curcumin and other curcuminoids; Submillimolar levels (<0.5 mM) of GSH and NAC rather improved their stability. Ascorbic acid or superoxide dismutase also stabilized curcumin regardless of their concentration. Cellular levels and bioactivities of curcumin including cytotoxicity and induction of heme oxygenase-1 were significantly reduced in the presence of 8 mM of GSH and NAC. The effects were enhanced in the presence of submillilmolar GSH and NAC, or non-thiol antioxidants. The present results indicate that antioxidants with reduced thiol group could directly interact with α, β-unsaturated carbonyl moiety of curcuminoids and modulate their stability and bioactivity.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

As the fast growth of information technology (IT), the safety of image transmission and the storing of images are increasingly concerned. Traditional image encryption algorithms have certain limitations in transmission and security, so there is an urgent need for a secure and reliable image encryption algorithm. A universal compression sensing (CS) image encryption (IE) algorithm based on DNA-triploid mutation (DTM) is presented in this paper. Firstly, by using CS algorithm an image is compressed while obtaining a range of chaotic sequences by iteration of chaotic map. Then DNA sequences are generated by encoding the image, and based on the DTM, new mutant DNA sequences are generated according to specific rules. Next, the chaotic sequences are operated at the DNA level to do confusion and diffusion operations on the image to ensure the security of the data. At last, DNA decoding is carried out to obtain the compressed-encrypted image. Both simulation experiments and performance tests fully show that a high level of security and reliability of the proposed algorithm in protecting image privacy is achieved.

In this paper, we extend the KdVSKR equations in (1+1)-dimension and (2+1)-dimension to fractional KdVSKR equations with modified Riemann-Liouville derivative. The (2+1)-dimensional KdVSKR equation, which is a recent extension of (1+1)-dimensional KdVSKR equation, can model the resonances of solitons in shallow water. By means of the Hirota bilinear method, finite symmetry group method and consistent Riccati expansion method, many new interaction solutions have been derived. Soliton-cnoidal interaction solution of the (1+1)-dimensional fractional KdVSKR equation has been derived for the first time. For the (2+1)-dimensional frac-tional KdVSKR equation, two-wave interaction solutions and three-wave interaction solutions, including dark-soliton-sine interaction solution, bright-soliton-elliptic interaction solution, and lump-hyperbolic-sine interaction solution, have been derived. Impact of the fractional order on the shapes of these solutions has been illustrated by figures. Three-wave interaction solutions of fractional systems have not been reported in the existing references. The research idea in this paper can be applied to other fractional differential equations.

Pluripotent stem cells (PSCs) can differentiate into three germ layers and diverse autolo-gous cell lines. Being among the most commonly used large domesticated hoofed animals and serving as a vital source of food and bioreactors, cattle are among the many species in which PSCs have been developed. Bovine PSCs (bPSCs) are the "seed cells" of regenerative science and have immense potential to advance species propagation, genetic engineering, and disease treatment. Moreover, they can aid in screening new drugs for efficacy and toxicity, model human diseases, and establish a sustainable agricultural system that can cater to the needs of the growing global population. Establishing stable bPSCs in vitro has been a critical scientific challenge, and researchers have made numerous attempts to address this issue. This review primarily delves into the current research progress of bPSCs, the challenges faced, and their potential applications.

Smallsats are becoming the predominant electro-optical Earth observation (EO) imaging platforms. While atmospheric correction of smallsat data enhances its utility, an established pathway to do so may constrain accuracy and utility. The alternative, Closed-form Method for Atmospheric Correction (CMAC), developed for smallsat application provides surface reflectance derived solely from scene statistics. In a prior paper, CMAC closely agreed with Land Surface Reflectance Code (LaSRC) software for correction of the four VNIR bands of Landsat-8/9 images for conditions of low to moderate atmospheric effect over quasi-invariant warehouse-industrial targets. Those results were accepted as surrogate surface reflectance to support analysis of CMAC and LaSRC reliability for surface reflectance retrieval in two contrasting environments: shortgrass prairie and barren desert. Reliability was defined and tested through a null hypothesis: the same top-of-atmosphere reflectance under the same atmospheric condition will provide the same estimate of surface reflectance. Evaluated against the prior surrogate surface reflectance, the results found decreasing error with increasing wavelength for both methods. From 58 comparisons across the four bands, LaSRC average absolute error ranged from 0.59% (NIR) to 50.30% (blue). CMAC error was well constrained from 0.01% (NIR) to 0.98% (blue) sustaining the null hypothesis for reliability.

With correct dynamic system parameters (embodied in self-awareness statements), a controller can provide precise signals for tracking desired state trajectories. If dynamic system parameters are initially guessed incorrectly, a learning method may be used to find the correct parameters. In the deterministic artificial intelligence method, self-awareness statements are formed as mathematical expressions of the governing physics. When the nonlinear, coupled expressions are precisely parameterized as the product of known matrix components and unknown victrix (i.e., a regression form) tracking errors may be projected onto the known matrix to update the unknown victrix in an optimal form (in a two-norm sense). In this work, a modified learning method is proposed and proved to have global convergence of both state error and parameter estimation error. The modified learning method is compared with those in the prequels using simulation experiments of three-dimensional rigid body dynamic rotation motion. The modified approach is two magnitudes better than the methods in the prequels in terms of state error convergence.

Nonlinear ultrasonic testing has been accepted as a promising manner for evaluating material integrity in an early stage. Stress fatigue is the main threats to train safety, railways examinations for stress fatigue are more significant and necessary. A series of ultrasonic nonlinear wave experiments are conducted for rail specimens extracted from railhead with different degree of fatigue produced by three-point bent loading condition. The nonlinear parameter is the indicator of nonlinear waves for expressing the degree the fatigue. The experimental results show that the sensitivity of a third harmonic longitudinal wave is higher than second harmonic longitudinal wave testing. As the same time, collinear wave mixing shows strong relative with fatigue damages than a second longitudinal wave NDT method and provides more reliable results than third harmonic longitudinal waves nonlinear testing method.

Under the action of cement hydration heat, construction environment, thermal insulation measures, and pipe cooling system, the mass concrete pile cap produces a complex temperature field inside the structure, which makes it difficult to control the internal surface temperature difference, the maximum adiabatic temperature rise and the surface temperature of the structure. In this paper, the mass concrete pile cap of a super large bridge (the length, width, and height are 26.40m，20.90m, and 5.00m, respectively, and the central pier pile cap is constructed with concrete with a strength of C40) is taken as the research support project. The controlling factors affecting the temperature field of the mass concrete pile cap are found by comparing the temperature monitoring of the pile cap with the calculated value of finite element software simulation analysis. Through the finite element software Midas Civil and Midas FEA, the control factors affecting the temperature field of the main pier cap (concrete mold temperature, concrete surface convection coefficient, ambient temperature, and pipe cooling system parameters, etc.) are numerically analyzed, and the influence law and influence degree of the control factors are found out.

Mulberry leaves, when infected by pathogens, can suffer significant yield loss or even death if early disease detection and timely spraying are not performed. To enhance the detection performance of mulberry leaf diseases in natural environments and to precisely locate early small lesions, we propose a high-precision, high-efficiency disease detection algorithm named YOLOv8-RFMD. Based on improvements to You Only Look Once version 8 (YOLOv8), we first proposed the Multi Dimension Feature Attention (MDFA) module, which integrates important features at the pixel-level, spatial and channel dimensions. Building on this, we designed the RFMD Module, which consists of the Conv-BatchNomalization-SiLU (CBS) module, Receptive-Field Coordinated Attention (RFCA) Conv, and MDFA, replacing the Bottleneck in the model’s Residual block. We then employed Adown down sampling structure to reduce the model size and computational complexity. Finally, to improve the detection precision of small lesion features, we replaced the complete intersection over union (CIOU) loss function with the Normalized Wasserstein Distance (NWD) loss function. Results show that the YOLOv8-RFMD model achieves an mAP50 of 94.3% and an mAP50:95 of 67.8% on experimental data, representing increases of 2.9% and 4.3% respectively compared to the original model. The model size is reduced by 0.53 MB to just 5.45 MB, and the number of floating-point operations is reduced by 0.3 G to only 7.8 G. The improved model meets the deployment requirements of mobile embedded devices and can provide a theoretical reference for the automated spraying operations of mulberry leaves.

BACKGROUND: Chronic hepatitis B infected with Hepatitis B virus remains a major health concern worldwide. Despite standard interferon-α and nucleotide analogues have been shown to reduce the deterioration of liver disease among chronic hepatitis B patients, covalently closed circular DNA was still difficult to eradicate. METHODS: A literature search of Pubmed and Web of science was performed with the following key words: ‘CRISPR’, ‘CRISPR/Cas9’, ‘hepatitis B’, ‘HBV’, ‘chronic hepatitis B’ and ‘HBV cccDNA’. The information about CRISPR/Cas9 for the treatment of HBV cccDNA or hepatitis B was reviewed. RESULTS: CRISPR/Cas9 could treat hepatitis B through suppressing or clearing HBV cccDNA with different gRNAs. CONCLUSION: With the emergence of CRISPR/Cas9 (the RNA-guided clustered regulatory interspaced short palindromic repeats, CRISPR) editing technology, clearance of hepatitis B virus and better prevention of liver carcinoma seemed to be possible.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

Microfluidic devices have been extensively investigated in recent years in fields including ligand-binding analysis, chromatographic separation, molecular dynamics, and DNA sequencing. To prolong the observation of a single molecule in aqueous buffer, the solution in a sub-micron scale channel is driven by the electric field and reversed after a fixed delay following each passage, so that the molecule passes back and forth through the laser focus and the time before irreversible photobleaching is extended. However, this practice requires complex chemical treatment to the inner surface of the channel to prevent unexpected sticking to the surface and the confined space renders features, such as a higher viscosity and lower dielectric constant, which slow the Brownian motion of the molecule compared to the bulk liquid. In this paper, we have fixed a capillary microchannel with an inner diameter of 2 microns on top of a piezo stage to recycle the molecule and collected the fluorescence by a confocal microscope. The passing times of the molecule through the laser focus are calculated by a real-time control system based on an FPGA and the commands of translation are given to the piezo stage through a feedback algorithm. We have achieved a maximum number of recycles of more than 200 and developed a maximum-likelihood estimation of the diffusivity of the molecule, which attains results of the same magnitude as previous reports. This technique simplifies the overall procedure of the single-molecule recycling and could be useful for the ligand-binding studies of biomolecules.

A large amount of accurate river cross-section data is indispensable for predicting river stages. However, the measured river cross-section data are usually sparse in the transverse direction at each cross-section as well as in the longitudinal direction along the river channel. This study presents three algorithms to resample the river cross-section data points in both the transverse and longitudinal directions from the original data. The resampled cross-section data based on the linear interpolation satisfactorily maintains the topographic and morphological features of the river channel, especially in the meandering river segment. A two-dimensional (2D) high-resolution unstructured-grid hydrodynamic model was used to assess the performance of the original and resampled cross-section data on a simulated river stage under low flow and high flow conditions. The simulated river stages are significantly improved using the resampled cross-section data based on the linear interpolation in the tidal river and non-tidal river segments. Furthermore, the performance of the 2D and three-dimensional (3D) models on the simulated river stage was also evaluated using the resampled cross-section data. The results indicate that the 2D and 3D models reproduce similar river stages in both tidal and non-tidal river segments under the low flow condition. However, the 2D model overestimates the river stages in both the tidal and non-tidal river segments compared to the 3D model under the high flow condition. The model sensitivity was implemented to investigate the influence of bottom drag coefficient and vertical eddy viscosity on river stage. The results reveal that bottom drag coefficient has a minor impact on river stage, but the vertical eddy viscosity is insensitive to river stage.

Rotavirus is a major cause of diarrhea globally in animals and young children under 5 years. Here, molecular detection and genetic characterization of porcine rotavirus in smallholder and commercial pig farms in the Lusaka Province of Zambia were con-ducted. Screening of 148 stool samples by RT-PCR targeting the VP6 gene revealed a prevalence of 22.9 % (34/148). Further testing of VP6-positive samples with VP7-specific primers produced 12 positives, which were then Sanger-sequenced. BLASTn of the VP7 positives showed sequence similarity to porcine and human rota-virus strains with identities ranging from 87.5% to 97.1%. By next-generation se-quencing, the full-length genetic constellation of the representative strains RVA/pig-wt/ZMB/LSK0137 and RVA/pig-wt/ZMB/LSK0147 were determined. Geno-typing of these strains revealed a known Wa-like genetic backbone and their genetic constellations were G4-P[6]-I5-R1-C1-M1-A8-N1-T1-E1-H1 and G9-P[13]-I5-R1-C1-M1-A8-N1-T1-E1-H1, respectively. Phylogenetic analysis revealed that these two viruses might have their ancestral origin from pigs, though some of their gene segments were related to human strains. The study shows evidence of reas-sortment and possible interspecies transmission between pigs and humans in Zambia. Therefore, the “One Health” surveillance approach for rotavirus A in animals and humans is recommended to inform the design of effective control measures.

Plant-derived compounds have been historically used for the treatment of various diseases and an important source of several clinically useful anti-cancer agents. The Artemisia annua is known as a medicinal herb that is effective against cancer. Thus, the purpose of this study was to investigate whether ethanol extracts of Artemisia annua could increase an anti-cancer effect against LS174T cells. Our results show that Artemisia annua extracts (AAE) induces apoptosis through the regulation of mitochondria outer membrane potential. We demonstrate that apoptosis is induced by p53-dependent manner when cells were treated with Nutlin-3 (MDM2 inhibitor) and LY294002 (Akt inhibitor). In addition, the apoptotic effect was also observed in the p53-independent manner through pifithrin-α (p53 inhibitor) and celecoxib (COX-2 inhibitor) treatment. As in in vitro, AAE induced apoptotic effects and regulated apoptosis-related proteins in LS174T xenograft model. Taken together, these results suggest that Artemisia annua extracts exerts an anti-cancer effect through p53-independent manner, as well as p53-dependent manner by p53´ translocation in LS174T colon cancer cells.

The emission of toxic gases from industrial production have intensified issues related to atmospheric pollution and human health. Consequently, the effective real-time monitoring and removal of these harmful industrial gases have emerged as significant challenges. In this work, the density functional theory (DFT) method was utilized to examine the adsorption behaviors and electrical characteristics of Ni-decorated InSe (Ni-InSe) monolayer when interacting with twelve gases (CO, NO, NO2, NH3, SO2, H2S, H2O, CO2, CH4, H2, O2 and N2). A comparative assessment of adsorption strength and sensing properties was performed through analyses of electronic structure, work function and recovery time. The results show that Ni doping enhances the electrical conductivity of the InSe monolayer and improves the adsorption capabilities for six toxic gases (CO, NO, NO2, NH3, SO2, H2S). Furthermore, the adsorption of these gases on the Ni-InSe surface is characterized as chemisorption, as indicated by the analysis of adsorption energy, density of states, and charge density difference. Additionally, the adsorption of CO, NO, NO2, and SO2 results in significant alterations to the bandgap of Ni-InSe, with changes of 18.65%, 11.37%, 10.62%, and –31.77%, respectively, underscoring its exceptional sensitivity. Moreover, the Ni-InSe monolayer exhibit moderate recovery times of 3.24 s and 22.72 s at 298 K for the SO2 and H2S, respectively. Consequently, the Ni-InSe is regarded as a promising gas sensor for detecting SO2 and H2S at room temperature. This research establishes a foundation for developing Ni-InSe based gas sensor in detecting and mitigating harmful gas emissions.

Green-space resources, in the context of urbanisation, cannot meet the actual needs of residents well, and the study of the balance of green-space resource allocation from the relationship between supply and demand is an urgent problem to be solved. This study quantitatively evaluates the green-space supply level from four dimensions by constructing a framework for assessment in the community life circle. It also evaluates the matching of green space supply and demand, resource distribution fairness, and distribution equilibrium under group differentiation through the supply–demand coupling matrix, Gini coefficient, and the Kruskal–Wallis H non-parametric rank-sum test, respectively. This study shows that (1) a significant spatial imbalance exists in green-space resource allocation in community life circles in different dimensions. (2) The comprehensive green-space supply level in the community life circle matched the total demand of residents to a low degree. (3) There was significant inequality in green-space resource allocation within the community life circle (the Gini coefficient of each evaluation perspective was > 0.4). Based on the study results, we were able to identify community life circles with spatial mismatches, different supply and demand, and other green-space resource allocation problems, which is of great significance to urban green-space research and planning practice under the "green justice" framework.

Most machine learning and deep learning algorithms can only use low-dimensional data as input, but the data that must be processed in practical applications is diverse and irregular. There are two main problems with big dynamic data. (1) The size of the embedding table grows linearly with the vocabulary size, resulting in massive memory consumption. (2) For different newly added vocabularies. To solve these two problems, this paper proposes a novel embedding algorithm that can learn attribute associations with entities based on deep and hash algorithms. Taking movie data as an example, the encoding method and the specific flow of the algorithm are presented in detail, and the effect of dynamic reuse of data models is realized. Compared with the four existing embedding algorithms which can fuse entity attribute information, the deep hash embedding algorithm proposed in this paper has obvious optimization of time and space complexity.