Subsurface drainage systems remove excess water from the soil profile thereby improving crop yields in poorly drained farmland. Knowledge of the position of the buried drain lines is important: 1) to improve understanding of leaching and offsite release of nutrients and pesticides, and 2) for the installation of a new set of drain lines between the old ones for enhanced soil water removal efficiency. Traditional methods of drainage mapping involve the use of tile probes and trenching equipment. While these can be effective, they are also time-consuming, labor-intensive, and invasive, thereby entailing an inherent risk of damaging the drainpipes. Non-invasive geophysical soil sensors provide a potential alternative solution. Previous research has focused on the use of time-domain ground penetrating radar (GPR), with variable success depending on local soil and hydrological conditions and the central frequency of the specific equipment employed. The objectives of this study were 1) to test the use of a stepped-frequency continuous wave (SFCW) 3D-GPR (GeoScope Mk IV 3D-Radar with DXG1820 antenna array) for subsurface drainage mapping, and 2) to evaluate the performance of a 3D-GPR with the use of a single-frequency multi-receiver electromagnetic induction (EMI) sensor (DUALEM) in-combination. The 3D-GPR system offers more flexibility for application to different (sub)surface conditions due to the coverage of wide frequency bandwidth. The EMI sensor simultaneously provides information about the apparent electrical conductivity (EC_a) for different soil volumes, corresponding to different depths. This sensor combination was evaluated on twelve different study sites with various soil types with textures ranging from sand to clay till. While the 3-D GPR showed a high success rate in finding the drainpipes at five sites (sandy, sandy loam, loamy sand, and organic topsoils), the results at the other seven sites were less successful due to limited penetration depth (PD) of the 3D-GPR signal. The results suggest that the electrical conductivity estimates produced by the inversion of EC_a data measured by the DUALEM sensor could be a useful proxy to explain the success achieved by the 3D-GPR in finding the drain lines. The high attenuation of electromagnetic waves in highly conductive media limiting the PD of the 3D-GPR can explain the findings obtained in this research.

River valley bottoms have hydrological, geomorphological, and ecological importance and are buffers for protecting the river from upland nutrient loading coming from agriculture and other sources. They are relatively flat, low-lying areas of the terrain that are adjacent to the river and bound by increasing slopes at the transition to the uplands. These areas have under natural conditions, a groundwater table close to the soil surface. The objective of this paper is to present a stepwise GIS approach for the delineation of river valley bottom within drainage basins and use it to perform a national delineation. We developed a tool that applies a concept called cost distance accumulation with spatial data inputs consisting a river network and slope derived from a digital elevation model. We then used wetlands adjacent to rivers as a guide finding the river valley bottom boundary from the cost distance accumulation. We present results from our tool for the whole country of Denmark carrying out a validation within three selected areas. The results reveal that the tool visually performs well and delineates both confined and unconfined river valleys within the same drainage basin. We use the most common forms of wetlands (meadow and marsh) in Denmark's river valleys known as Groundwater Dependent Ecosystems (GDE) to validate our river valley bottom delineated areas. Our delineation picks about half to two-thirds of these GDE. However, we expected this since farmers have reclaimed Denmark's low-lying areas during the last 200 years before the first map of GDE was created. Our tool can be used as a management tool, since it can delineate an area that has been the focus of management actions to protect waterways from upland nutrient pollution.

In order to enable patients with severe disabilities who have lost their limbs to accurately control their wheelchair movement and optimize the power loss of smart wearable tongue control devices, a non-invasive intraoral stand-alone tongue control system based on RSIC-V edge computing is proposed in this paper. Patients can detect the pressure signal of the tongue muscles’ touching the palate by placing the flexible carbon nanotube-PDMS pressure sensor array in the mouth, and the erroneous movement signal can be avoided by setting the pressure threshold, thereby improving the reliability of the device and the user's experience. The system converts the pressure data into specific control instructions on the edge of the RSIC-V chip and transmits them to the receiver, thus reducing the transmission of data. In this experiment, the speed response time test, the center click task and the power consumption experiment are carried out, whose results show that the adaptive fuzzy PID control algorithm has good robustness in the system: when the DC motor with a given speed of 750r/min reaches the steady state, its rise time is 0.108s and the adjustment time is 0.59s. The dynamic power consumption of the non-intrusive intraoral stand-alone tongue control system proposed in this paper is tested to be 3.745 MW, which is 11.5% lower than the total power consumption of the sTDs system.

The aim was to study alterations of bacterial communities in patients undergoing hip or knee arthroplasty to assess the impact of chlorhexidine gluconate soap decolonisation and systemic antibiotic prophylaxis. A Swedish multicentre, prospective collection of samples obtained from elective arthroplasty patients (n=83) by swabbing anterior nares, skin sites in the groin and the site of planned surgery, before and after arthroplasty surgery, was analysed by 16S rRNA (V3-V4) gene sequencing and a complementary targeted tuf gene sequencing approach to comprehensively characterise alterations in staphylococcal communities. Significant reductions in alpha diversity was detected for both bacterial (p=0.04) and staphylococcal (p=0.03) groin communities after arthroplasty surgery with significant reductions in relative Corynebacterium (p=0.001) abundance and S. hominis (p=0.01) relative staphylococcal abundance. In nares, significant reductions occurred for S. hominis (p=0.02), S. haemolyticus (p=0.02), and S. pasteuri (p=0.003) relative to other staphylococci. S. aureus colonised 35% of anterior nares before and 26% after arthroplasty surgery. S. epidermidis was the most abundant staphylococcal species at all sampling sites. No bacterial genus or staphylococcal species increased significantly after arthroplasty surgery. Application of a targeted tuf gene sequencing approach provided auxiliary staphylococcal community profiles and allowed species-level characterisation directly from low biomass clinical samples.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

Landslide is one of the most common geological disasters in China, which is characterized by suddenness and uncertainty, and it is difficult to realize accurate identification, early warning and forecasting of landslide disaster by conventional means. With the development of high-resolution remote sensing satellites and InSAR surface deformation monitoring technology, the traditional means of landslide monitoring data sources are limited, and there is a lack of effective methods to excavate the characteristics of the spatial distribution of landslide hazards and their triggering factors and other issues. In this paper, the area extending 10 km outside the VII isobar of the Gengma earthquake is taken as the study area, and 13 evaluation factors are screened out by integrating the factors of InSAR surface deformation, topography and geological environment, and the Bayesian Optimized Convolutional Neural Network (BO-CNN) is used for the evaluation of landslide susceptibility, and the BO-RF and PSO-SVM models are selected for the comparative analysis. The model accuracy evaluation was carried out by three indexes: ROC curve, AUC value and FR value, in which the ROC curves of PSO-SVM, BO-RF and BO-CNN were all close to the upper-left corner of the corner, and the AUC values were 0.9388, 0.9529, and 0.9535, respectively, and the FR value of landslide in the high susceptibility area of BO-CNN was as high as 14.9, and was higher than that of PSO-SVM and BO-RF, respectively. SVM and BO-RF model is 4.55 and 3.69 higher, the experimental results show that the BO-CNN model used in this paper has a better effect in landslide susceptibility evaluation, and the research results of the local government's disaster prevention and mitigation measures are of great significance.

Concurrent Optical and Magnetic Stimulation (COMS) combines extremely low frequency electromagnetic and light stimulation modalities for enhanced wound healing. In this report, we investigated the potential mechanistic synergism between magnetic and light components by comparing their individual and combined cellular responses. Although each individual stimulation mode was capable of stimulating cell proliferation, magnetic fields exposure alone produced greater proliferation enhancement than light alone, yet their combined effects of were supra-additive of the individual responses. Reactive oxygen species were incrementally reduced by exposure to light, magnetics fields and their combination, where statistical significance was ultimately achieved. On the other hand, ATP production was significantly enhanced in response to magnetic exposure alone or in combination with light. These results suggest that mitochondrial respiratory efficiency was preferentially improved by the combination of the two stimuli. Protein expression related to cell proliferation was preferentially enhanced by the combinatory COMS modality as were the protein levels of the TRPC1 cation channel previously implicated as part of a calcium-mitochondrial signaling axis invoked by electromagnetic exposure and involved in proliferation. These results corroborate that light facilitates functional synergism with magnetic fields that ultimately impinge on mitochondria-dependent developmental responses. The aminoglycoside antibiotics (AGAs) have been previously shown to antagonize TRPC1-mediated magnetotransduction. Streptomycin applied during the exposure to any of the stimulation modes reduced proliferation enhancement, whereas streptomycin added after the exposure did not. Notably, the COMS modality and magnetic field exposure were capable of partially overcoming streptomycin antagonism of proliferation, whereas light alone was not. Transductional antagonism of combinatorial photon-electromagnetic effects by streptomycin thus aligns with previous studies showing that the AGAs block TRPC1-mediated magnetotransduction when applied during exposure. The prophylactic usage of the AGAs (neomycin) should be avoided during COMS therapy to maintain clinical efficacy and would be a common concern with most other electromagnetic regenerative paradigms.

Transcription is carried out in most eukaryotes by three multimeric complexes (RNA polymerases I, II and III). However, plants contain two additional RNA polymerases (IV and V), which have evolved from RNA polymerase II. RNA polymerases II, IV and V contain both common and specific subunits that may specialize some of their functions. In this study, we conducted a search for the genes that putatively code for the specific subunits of RNA polymerases IV and V, as well as the corresponding of RNA polymerase II in olive. Based on the homology with the genes of Arabidopsis thaliana, we identified 13 genes that putatively code for the specific subunits of polymerases IV and V, and 16 genes that code for the corresponding specific subunits of polymerase II in olive. The transcriptomic analysis by RNA-Seq revealed that the expression of the RNA polymerases IV and V genes was induced during the initial stages of fruit development. Given that RNA polymerases IV and V are involved in the transcription of long non-coding RNAs, we investigated their expression and observed relevant changes in the expression of this type of RNAs. Particularly, the expression of the intergenic and intronic long non-coding RNAs tended to increase in the early steps of fruit development, suggesting their potential role in this process. The positive correlation between the expression of RNA polymerases IV and V subunits and the expression of non-coding RNAs supports the hypothesis that RNA polymerases IV and V may play a role in fruit development throughout the synthesis of this type of RNAs.

In this work, we investigated the effects of heat treatment on the microstructure, hydrogen storage characteristics and corrosion rate of a Ti₃₄V₄₀Cr₂₄Fe₂ alloy. The arc melted alloy was divided into three samples, two of which were separately quartz-sealed under vacuum and heated to 1000 °C for 1 h; one of these samples was quenched and the other furnace cooled to ambient temperature. The crystal structures of the samples were studied via X-ray diffractometry and scanning electron microscopy. Absorption/desorption characteristics were investigated using a Sievert apparatus. Potentiostat corrosion tests on the alloys were performed using an AutoLab^® corrosion test apparatus and electrochemical cell. All samples exhibited a mixture of body-center-cubic (BCC) and Laves phase structures. The corrosion rate, maximum absorption, and useful capacities increased after both heat treatments. The annealed sample had the highest absorption and reversible capacity. The plateau pressure of the as-cast alloy increased after quenching. The corrosion rate increased from 0.0004 mm/y in as-cast sample to 0.0009 mm/y after annealing and 0.0017 mm/y after quenching, due to a decrease in the Cr-content of the C14 phase.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

The study of the impact of polyQ expansion driven proteotoxicity on cell metabolism has evi-denced NAD molecule as a central player in regulating metabolic response and cell repair in neurodegeneration. The decline in NAD intracellular levels represents a hallmark of ageing aris-ing from a dysregulation between NAD-consuming and biosynthetic enzymatic reactions in which NMNAT plays a key role. By an integrated bioanalytical and proteomic experimental design, the derangement of NAD metabolism deriving from the accumulation of polyQ-Htt protein has been analysed in Saccha-romices cerevisiae harbouring a 103Q-Htt and compared with wild-type Htt, in absence and in presence of a phenolic extract from EVOO, as a source of antioxidant bioactive compounds. Quantification of NAD and its precursors and proteomic analysis of the differential protein ex-pression has been performed by LC-DAD-MS. Chronological lifespan and NAD homeostasis was strongly impaired by proteotoxic polyQ-Htt, eliciting a depletion of NAD levels and accumulation of NaMN. In parallel a downregulation of Sirt2 expression levels has been observed. Phenolic extract administration had no meaningful ef-fects on NAD replenishment to prevent proteotoxicity. NaMN can represent a biomarker of accel-erated aging, and/or a signaling molecule for cell repair.

In this study, the term dimension is introduced on fuzzy(neutrosophic) graphs. The classes of these specific graphs are chosen to obtain some results based on dimension. The types of crisp notions and fuzzy(neutrosophic) notions are used to make sense about the material of this study and the outline of this study uses some new notions which are crisp and fuzzy(neutrosophic).

The prevailing interpretations of physics are based on deeply entrenched assumptions, rooted in classical mechanics. Logical implications include: the denial of entropy as a fundamental physical property, and the inability to explain irreversible change, random quantum measurements, or nonlocality without untestable and implausible metaphysical implications. We propose a conceptual model that is based on empirically justifiable assumptions and consistent with observations. The WYSIWYG Conceptual Model (WCM) assumes no hidden properties: “What You can See Is What You Get.” The WCM contextually defines a system’s state with respect to its actual ambient background, and it extends existing models of physical reality by defining entropy and exergy as objective contextual properties of state. The WCM establishes the irreversible dissipation of exergy and the Second law of thermodynamics as a fundamental law of physics, it recognizes physical randomness, and it provides a physical explanation for nonlocality, consistent with Special Relativity, without hidden variables, superdeterminism, or “spooky action.”

The aim of this work is to introduce new ways to model the I-V characteristic of a PV cell or PV module using straight lines and Bézier curves. This is a complete novel approach, Bézier curves being previously used mainly for computer graphics. The I-V characteristic is divided in three sections, modeled with lines and a quadratic Bézier curve in the first case and with three cubic Bézier curves in the second case. The result proves to be accurate and relies on the fundamental points usually present in the PV cell datasheets: Voc (the open circuit voltage), Isc (the short circuit current), Vmp (the maximum power corresponding voltage) and Imp (the maximum power corresponding current) and the parasitic resistances Rsh0 (shunt resistance at Isc) and Rs0 (series resistance at Voc). The proposed algorithm completely defines all the implied control points and the error is analyzed. The temperature and irradiance influence is also analyzed. The model is also compared using the least squares fitting method. The final validation shows how to use Bézier cubic curves to accurately represent the I-V curves of an extensive range of PV cells and arrays.

BACKGROUNDː The so-called Low Cardiac Output Syndrome (LCOS) is one of the most common complications in pediatric patients with congenital heart disease undergoing corrective surgery. LCOS requires high concentrations of inotropes to support cardiac contractility and improve cardiac output, allowing for a better systemic perfusion. To date, serum lactate concentrations and central venous oxygen saturation (ScVO2) are the most commonly used perfusion markers, but they are not completely reliable to identify a state of global tissue hypoxia. The study aims to evaluate whether the venoarterial carbon dioxide difference/arterial-venous oxygen difference ratio [P(v-a)CO2/C(a-v)O2] can be a good index to predict the development of LCOS in the aforemen-tioned patients, so as to treat it promptly. METHODSː This study followed a population of 98 children undergoing corrective cardiac surgery from June 2018 to October 2020 at the Department of Cardiac Surgery of University Hospital Inte-grated Trust and their subsequent admission at the Postoperative Cardiothoracic Surgery Intensive Care Unit. During the study, central arterial and venous blood gas analysis were carried out before and after cardiopulmonary bypass (CPB) (pre-CPB and post-CPB), at admission to intensive care unit, before and after extubation and at any time of instability or modification of the patient’s clinical and therapeutic conditions. RESULTSː The data analysis shows that 46.9% of the children developed a LCOS (in line with the current literature) but that there is no statistically significant association between the P(v-a)CO2/C(a-v)O2 ratio and LCOS onset. Despite the limits of statistical significance, however, a 31% increase in the ratio emerged from the pre-CPB phase to the post-CPB phase when LCOS is present. CONCLUSIONSː This study confirms a statistically significant association between the most used markers in adult patients (serum lactate concentration, ScVO2 and oxygen extraction ratio-ERO2) measured in the pre-CPB phase and the incidence of LCOS onset, especially in patients with he-modynamic instability before surgery.

Control over the composition of III-V ternary nanowires grown by the vapor-liquid-solid (VLS) method is essential for bandgap engineering in such nanomaterials and fabrication of functional nanowire heterostructures for a variety of applications. From the fundamental viewpoint, III-V ternary nanowires based on group V intermix (InSbxAs1-x, InPxAs1-x, GaPxAs1-x and many others) present the most difficult case, because the concentrations of highly volatile group V atoms in a catalyst droplet are beyond the detection limit of any characterization technique and therefore principally unknown. Here, we present a model for the vapor-solid distribution of such nanowires, which fully circumvents the uncertainties that remained in the theory so far, and link the nanowire composition to the well-controlled parameters of vapor. The unknown concentrations of group V atoms in the droplet do not enter the distribution, despite of the fact that a growing solid is surrounded by the liquid phase. The model fits quite well the available data on the vapor-solid distributions of VLS InSbxAs1-x, InPxAs1-x and GaPxAs1-x nanowires grown with different catalyst. Even more importantly, it provides a basis for the compositional control of III-V ternary nanowires based on group V intermix, and can be extended over other material systems where two highly volatile elements enter a ternary solid alloy through a liquid phase.

We prove an analog of the removable singularity theorem for bounded harmonic functions on stratified sets. The harmonic functions are understood in the sense of the soft Laplacian. The result can become one of the main technical components for extending the well-known Poincaré–Perron’s method of proving the solvability of the Dirichlet problem for the soft Laplacian.

Background: Fullerenes and metallofullerenes can be considered promising nanopharmaceuticals themselves and as a basis for chemical modification. As reactive oxygen species homeostasis plays a vital role in cells, the study of their effect on genes involved in oxidative stress and anti-inflammatory response is of particular importance. Methods: Human fetal lung fibroblasts were incubated with aqueous dispersions of C60, C70, and Gd@C82 in concentrations of 5 nM and 1.5 µM for 1, 3, 24, and 72 hours. Cell viability, intracellular ROS, NOX4, NFκB, PRAR-γ, NRF2, heme oxygenase 1, and NAD(P)H quinone dehydrogenase 1 expression have been studied. Results & conclusion: The aqueous dispersions of C60, C70, and Gd@C82 fullerenes are active participants in ROS homeostasis. Low and high concentrations of AFDs have similar effects. C70 was the most inert substance, C60 was the most active substance. All AFDs have both a “prooxidant” and “antioxidant” effect, but with a different balance. Gd@C82 was a substance with more pronounced antioxidant and anti-inflammatory properties, while C70 had more pronounced “prooxidant” properties.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

Smallsats are becoming the predominant electro-optical Earth observation (EO) imaging platforms. While atmospheric correction of smallsat data enhances its utility, an established pathway to do so may constrain accuracy and utility. The alternative, Closed-form Method for Atmospheric Correction (CMAC), developed for smallsat application provides surface reflectance derived solely from scene statistics. In a prior paper, CMAC closely agreed with Land Surface Reflectance Code (LaSRC) software for correction of the four VNIR bands of Landsat-8/9 images for conditions of low to moderate atmospheric effect over quasi-invariant warehouse-industrial targets. Those results were accepted as surrogate surface reflectance to support analysis of CMAC and LaSRC reliability for surface reflectance retrieval in two contrasting environments: shortgrass prairie and barren desert. Reliability was defined and tested through a null hypothesis: the same top-of-atmosphere reflectance under the same atmospheric condition will provide the same estimate of surface reflectance. Evaluated against the prior surrogate surface reflectance, the results found decreasing error with increasing wavelength for both methods. From 58 comparisons across the four bands, LaSRC average absolute error ranged from 0.59% (NIR) to 50.30% (blue). CMAC error was well constrained from 0.01% (NIR) to 0.98% (blue) sustaining the null hypothesis for reliability.

A polymer inclusion membrane (PIM) composed of 50 wt% poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) as its base polymer, 40 wt% Aliquat® 336 as its extractant and 10 wt% dibutyl phthalate (DBP) as plasticizer provided efficient extraction of vanadium(V) from its sulfate solutions adjusted to pH 2.5. It was suggested that V(V) was extracted as VO2SO4− via an anion exchange mechanism. Quantitative back-extraction was achieved in a sulfuric acid solution (6 mol L-1) containing 1 v/v% of hydrogen peroxide. It was assumed that the back-extraction process involved the oxidation of VO2+ to VO(O2)+ by hydrogen peroxide. The newly developed PIM with the optimized composition mentioned above exhibited excellent selectivity for V(V) in the presence of metallic species present in digests of spent alumina hydrodesulfurization catalysts (i.e., Al(III), Co(II), Cu(II), Fe(III), Mn(II), and Ni(II)). The co-extraction of Mo(VI) with V(V) was eliminated by its selective extraction at pH 1.1. The optimized PIM was characterized by contact angle measurements, atomic-force microscopy (AFM), energy dispersive X-ray spectroscopy (EDS), thermogravimetric analysis (TGA)/derivatives thermogravimetric analysis (DTGA), and the stress-strain measurements.

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

In this paper, we define a (p,v)-extension of Hurwitz-Lerch Zeta function by considering an extension of beta function defined by Parmar et al. [J. Classical Anal. 11 (2017) 81–106]. We obtain its basic properties which include integral representations, Mellin transformation, derivative formulas and certain generating relations. Also, we establish the special cases of the main results.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

This review summarizes the most recent developments of research on protozoan parasite infections ac-quired through food and drinking water and is aimed at gathering updated knowledge on the risk factors, illnesses caused, and measures for prevention. Reports included dated from 2019 to the present and regarded recent outbreaks and cases of severe infec-tions, prevalence in different population segments and food handlers, and occurrence in food and drinking water. Cryptosporidium spp., Entamoeba histolytica, Giardia intestinalis, Trypanosoma cruzi and Toxoplasma gondii were the microorganisms most frequently involved in large outbreaks and/or severe infections, while Cyclospora cayetanensis was most frequently involved in single case reports. Cystoisospora belli was implied in severe infections in immunocompromised patients, while Blastocystis homi-nis, Sarcocystis spp., Dientamoeba fragilis, Endolimax nana and Pentatrichomonas hominis appeared to be less relevant for number of symptomatic infections and pathogenic potential. A progressive improvement in surveillance of protozoan infections and infection sources was highlighted, especially in developed countries. The apparent increase in cases was concomitant with the implementa-tion of reporting systems and the application of molecular diagnostic methods that represent valuable in-struments for establishing epidemiological links and preventing or limiting outbreaks. The pathogenic role and sources of infection should be better elucidated for some species.

Transketolase (TKT) is an essential thiamine diphosphate (ThDP)-dependent enzyme of the non-oxidative branch of pentose phosphate pathway, with the glucose-6P flux through the pathway regulated in various medically important conditions. Here, we characterize the brain TKT regulation by acylation in rats with perturbed thiamine-dependent metabolism, known to occur in neurodegenerative diseases. The perturbations are modelled by administration of oxythiamine inhibiting ThDP-dependent enzymes in vivo, or by reduced thiamine availability in the presence of metformin and amprolium, inhibiting intracellular thiamine transporters. Compared to control rats, chronic administration of oxythiamine does not significantly change the modification level of the two detected TKT acetylation sites (K6 and K102), but doubles malonylation of TKT K499, concomitantly decreasing 1.7-fold the level of demalonylase sirtuin 5. The inhibitors of thiamine transporters do not change average levels of TKT acylation or sirtuin 5. TKT structures indicate that the acylated residues are distant from the active sites. The acylations-perturbed electrostatic interactions may be involved in conformational shifts and/or formation of TKT complexes with other proteins or nucleic acids. Acetylation of K102 may affect the active site entrance/exit and subunit interactions. Correlation analysis reveals that the action of oxythiamine is characterized by significant negative correlations of K499 malonylation or K6 acetylation with TKT activity, not observed upon the action of the inhibitors of thiamine transport. However, the transport inhibitors induce significant negative correlations between the TKT activity and K102 acetylation or TKT expression, absent in the oxythiamine group. Thus, perturbations in the ThDP-dependent catalysis or thiamine transport manifest in the insult-specific patterns of the brain TKT malonylation and acetylations.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Abstract: Two novel low-dimensional molecular magnetic materials were prepared by a self-assembling of 3d- and 5d-metal complexes. These are the first neutral heterobimetallic cyanobridged compounds involving one anisotropic Mn(III) Schiff base complex and one octacyanotungstate(V) per molecular unit. A slow diffusion of the constituents’ solutions leads to a formation of the 0D crystalline complex 1 due to coordination of a water molecule to the Mn center prevents a polymer formation. A rapid mixing of reagents results in a precipitation of the microcrystalline powder of the complex 2, which on a totality of experimental data possess 1D polymeric structure. The magnetic studies have shown that antiferromagnetic exchange interactions are dominating in 1 J/k_B= -13.1(7) K, D=-3.0(1.3) K, zJ'= -0.16(20) K and g_av=2.00(1); while the presence of the significant intramolecular Mn(III)–W(V) ferromagnetic couplings through cyanide bridges is characteristic for 2 (J/k_B = 46.1(5) K g_Mn = 2.11(3), fixed g_W = 2.0). Due to the weak interchain interactions, zJ'/k_B = –0.8(2) K, compound 2 is a metamagnet with the Néel temperature of 9.5 K undergoing a spin-flip transition at 2 kOe. The slow magnetization dynamics of 2 was investigated at DС field of 0 and 2 kOe, giving the values of τ₀ 32(15) and 36(15) ps respectively, well within the range typical for SCMs. The respective ∆_τ/k_B values were 48.4(1.2) and 44.9(1.0) K.

Abstract: Chloroplast is a new hotspot in the field of plant transformation system of plant genetic engineering. Initially developed in Chlamydomonas and tobacco, it is now feasible in a broad range of species. They exploit the homologous recombination and segregation pathways acting on chloroplast genomes and are based on direct repeats, transient co-integration or co-transformation and segregation of trait and marker genes. Foreign site-specific recombinases and their target sites provide an alternative and effective method for removing marker genes from plastids.Chloroplast genetic engineering has many advantages over nuclear genetic enginering, especially site-specific introduction of foreign genes ,leading to the absence of gene siliency and positon effect,which providing the available to explore the regulation and mechanism of chloroplast genes`expression in vitro .It also can identify the structure and function of the chloroplast genome , the expression of chloroplast affect the nulear genome. In this paper, the basic methodology of chloroplast transformation, the current techniques and applications, and the future possibilities for Chloroplast genetic engineering was reviewed[1-3].

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

Over the few decades, cancer-associated mortalities and morbidities were continuously increased worldwide despite sophisticated technological advancements. Pharmaceutical interventions associated with drugs exhibit a high degree of side effects and toxicities in addition to very high costs. Subsequently, to reduce or to vanish the side effects and high costs, researchers are now exploring natural bioactive compounds such as quercetin in its nanoformulations along with biologics as cargo delivery vehicles. Quercetin along with mesenchymal stromal lineage-derived extracellular vesicles (EVs) possesses an anti-cancer potential that can be explored to treat hepatocellular carcinoma (HCC). Exerting enhanced effect, nano quercetin synergistically with EVs triggers the anti-cancer mechanisms by regulating and dysregulating several signalling mechanisms including NF-κB, p53, JAK/STAT, MAPK, Wnt/β-catenin and PI3K/AKT, in addition to PBX3/ERK1/2/CDK2, and miRNAs modulation. In addition, findings regarding the potential checkpoints of anti-cancer signalling pathways were investigated that offer opportunities to develop engineered EVs incorporated with nano quercetin for the development of novel therapeutics to treat HCC in future. In this present mechanistic review, we abridged the regulation of such signalling mechanisms synergetic approach of nano quercetin and EVs. The regulatory role of EVs in the manifestation of innumerable miRNAs has also been tailed with special context to HCC.

We analyse recent contradictory results and conclusions about the spectrum of the screened Coulomb potential $V(r)=-r^{-1}e^{-C/r}$. The well known Hellmann-Feynman theorem shows that all the bound states of the Coulomb potential ($C=0$) remain bounded as $C$ increases. We derive a simple approximate analytical expression for the eigenvalues for sufficiently small values of the screening parameter $C$ and an approximate asymptotic expression for the asymptotic behaviour of the s-state eigenvalues when $C\rightarrow \infty $. Present results are expected to resolve the discrepancy about the spectrum of the quantum-mechanical model just mentioned.

Objectives: This study aimed to analyze the awareness of local residents regarding healthcare projects and to suggest some ideas for the revision of local ones. Methods: To delve into the opinions of local residents, the author of this study created a questionnaire composed of eight questions on the general characteristics of the respondents, eight questions on satisfaction with health centers, 16 questions on the awareness of healthcare projects, and 22 questions on local healthcare. The survey was conducted for 409 residents who visited public centers in Gimcheon from 15 March to 14 April 2021. Results: Data analysis revealed the following: The proportion of local residents who use health centers was 39.1%, and those users visit health centers, on average, 3.92 times a year. Among healthcare projects, the project known by the highest proportion of people was vaccinations (84.5%), which was also the project that was most used (38.1%). Among healthcare projects needed in the with-COVID-19 age, respondents awarded the highest score to vaccinations (4.15 points on a five-point Likert scale) and the second highest score to infectious disease management (4.12). Conclusions: For healthcare projects, central and local governments should focus on activating vaccinations, solving the problem of medical accessibility through untact remote treatment and establishing national infectious disease-specializing hospitals and local infectious disease management based on such national hospitals.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

Changes in coastal topography can affect the ecological environment and marine industries. In this study, we analyzed the patterns and causes of changes in shoreline and undersea topography in the Nakdong River estuary in the southeast of South Korea using depth and shoreline surveys of the estuary, as well as data on discharge, suspended sediments, and precipitation in the Nakdong River basin. The results showed that erosion and sedimentation occurred repeatedly owing to complex factors such as the discharge of the estuary and invasion by open sea waves. However, no clear unilateral trend was observed. Unlike previous survey data, a large amount of erosion occurred in the second half of 2020. Previously, sedimentation was the main process, but erosion occurred rapidly, which was observed in the summer of 2020 when the erosion was three times higher than that in other periods owing to the severe rainy season and torrential rains for over a month. In addition, regarding the flow rate and force of the river water outflow, the amount of discharge increased rapidly, causing erosion. Moreover, a strong typhoon in the summer of 2020 affected the topography of the estuary.

The removal of harmful arsenic(V) from aqueous solutions using Cyanex 923 (solvation extractant) was investigated under various experimental variables: equilibration time, acidity of the aqueous phase, temperature, extractant and arsenic concentrations, and O/A ratio. Cyanex 923 extracted As(V) (and sulphuric acid) from acidic solutions, thus, its use to remove the metal from slightly acid or neutral solutions it is not possible. Extraction of arsenic is exothermic, and responded to the formation of H3AsO4·nL species in the organic phase (L represented the extractant and the stoichiometric factor n: 1 or 2, depends on the acidity of the aqueous phase). Extraction isotherms are derived from experimental results. Both arsenic and sulphuric acid loaded onto the organic phase can be stripped with water, and stripping isotherms are also derived from the experimental results. The selectivity of the system against the presence of other metals (Cu(II), Ni(II), Bi(III), Sb(III)) are investigated, and also it is investigated the ability of Cyanex 923 to extract As(V) and sulphuric acid against the use of other P=O based solvation reagents, such dibutyl butylphosphonate (DBBP) and tri-butyl phosphate (TBP).

A novel type of phosphazene containing additive that act both as catalyst and as flame retardant for benzoxazine binders is presented in this study. The synthesis of a derivative of hexachlorocyclotriphosphazene (HCP) and meta-toluidine was carried out in the medium of the latter, which made it possible to achieve complete substitution of chlorine atoms in the initial HCP. Thermal and flammability characteristics of modified compositions are revealed. The modifier catalyzes the process of curing and shifts the beginning of reaction from 222.0 C for pure benzoxazine to 205.9 C for composition with 10 phr of modifier. The additive decreases the glass transition temperature of compositions. Achievement of the highest category of flame resistance (V-0 in accordance with UL-94) is ensured both by increasing the content of phenyl residues in the composition and by the synergistic effect of phosphorus and nitrogen. Brief research of the curing kinetics disclosed the complex nature of the reaction. An accurate two-step model is obtained using extended Prout-Tompkins equation for both steps.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

Avian influenza viruses (AIVs) are highly contagious respiratory viruses of birds, lead-ing to significant morbidity and mortality globally and causing substantial economic losses to the poultry industry. Since their first isolation in 2013, the Asian-origin H5N1 highly pathogenic avian influenza viruses (HPAI) of clade 2.3.4.4b have undergone unprecedented evolution and re-assortment of internal gene segments and have spread to Asia, Europe, Africa, and America, caus-ing outbreaks in all the poultry categories. Novel epidemiological and pathobiological character-istics, distinct from other clades, are specific of clade 2.3.4.4b viruses. Wild waterfowl, the natu-ral reservoir of AIVs, are frequently found infected with clade 2.3.4.4b viruses, which can also cause high morbidity and mortality in these birds. The sustained clade 2.3.4.4b virus circulation in waterfowl has also led to virus infection in other wild bird species, with implications for the conservation of endangered species. Furthermore, clade 2.3.4.4b viruses have been isolated in var-ious wild and domestic mammals worldwide, and critical mutations related to virus adaptation to mammalian species have been identified, raising concerns about virus spillover to humans. The main clinical signs, and anatomopathological findings associated to clade 2.3.4.4b virus infection in birds and non-human mammals are hereby summarized.

Vertical III-V semiconductor nanowires have shown promising absorption of light for solar cell and photodetector applications. The absorption properties can be tuned through the choice of III-V materials and geometry of the nanowires. Here, we review recent progress in the design of the absorption properties of both individual nanowires and nanowire arrays. Future directions for the research field are proposed.

Metal hyperaccumulating plants should have extremely efficient defence mechanisms, enabling growth and development in a polluted environment. Brassica species are known to display hyperaccumulation capability. Brassica juncea (Indiana mustard) v. Malopolska plants were exposed to trace elements, i.e., cadmium (Cd), copper (Cu), lead (Pb), and zinc (Zn), at a concentration of 50 M and were then harvested after 96 hours for analysis. We observed a high index of tolerance (IT), higher than 90%, for all B. juncea plants treated with the four metals, and we showed that Cd, Cu, Pb and Zn accumulation was higher in the above-ground parts than in the roots. We estimated the metal effects on the generation of reactive oxygen species (ROS) and the levels of protein oxidation as well as on the activity and gene expression of antioxidant enzymes, including superoxide dismutase (SOD), catalase (CAT) and ascorbate peroxidase (APX). The obtained results indicate that organo-specific ROS generation was higher in plants exposed to essential metal elements (i.e., Cu and Zn), compared with non-essential ones (i.e., Cd and Pb), in conjunction with SOD, CAT and APX activity and expression at the level of encoding mRNAs and existing proteins. In addition to the potential usefulness of B. juncea in the phytoremediation process, the data provide important information concerning plant response to the presence of trace metals.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

Small interfering RNA (siRNA) holds significant therapeutic potential by silencing target genes through RNA interference. Current clinical applications of siRNA have been primarily limited to liver diseases, while achievements in delivery methods are expanding its applications to various organs, including the lungs. Cholesterol-conjugated siRNA emerges as a promising delivery approach due to its low toxicity and high efficiency. This study focuses on developing a cholesterol-conjugated anti-Il6 siRNA and the evaluation of its potency for the potential treatment of inflammatory diseases using the example of acute lung injury (ALI). The biological activities of different Il6-targeted siRNAs containing chemical modifications were evaluated in J774 cells in vitro. The lead cholesterol-conjugated anti-Il6 siRNA after intranasal instillation demonstrated dose-dependent therapeutic effects in a mouse model of ALI induced by lipopolysaccharide (LPS). The treatment significantly reduced Il6 mRNA levels, inflammatory cell infiltration, and the severity of lung inflammation. IL6 silencing by cholesterol-conjugated siRNA proves to be a promising strategy for treating inflammatory diseases, with potential applications beyond the lungs.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

Veratrum californicum is a rich source of steroidal alkaloids such as cyclopamine, a known inhibitor of the Hedgehog (Hh) signaling pathway. Here we provide a detailed analysis of the alkaloid composition of V. californicum by plant part through quantitative analysis of cyclopamine, veratramine, muldamine and isorubijervine in the leaf, stem and root/rhizome of the plant. To determine if additional alkaloids in the extracts contribute to Hh signaling inhibition, we replicated the concentrations of these alkaloids observed in extracts using commercially available standards and compared the inhibitory potential of the extracts to alkaloid standard mixtures using Shh-Light II cells. Alkaloid combinations enhanced Hh signaling pathway antagonism compared to cyclopamine alone, and significant differences were observed in the Hh pathway inhibition between the stem and root/rhizome extracts and their corresponding alkaloid standard mixtures, indicating that additional alkaloids present in these extracts contribute to Hh signaling inhibition.

Integrated ultra-low-loss waveguides are highly desired for integrated photonics to enable applications that require long delay lines, high-Q resonators, narrow filters, etc. Here we present an ultra-low-loss silicon waveguide on 500 nm thick SOI platform. Meter-scale delay lines, million-Q resonators and tens of picometer bandwidth grating filters are experimentally demonstrated. We design a low-loss low-reflection taper to seamlessly integrate the ultra-low-loss waveguide with standard heterogeneous Si/III-V integrated photonics platform to allow realization of high-performance photonic devices such as ultra-low-noise lasers and optical gyroscopes.

A new method for the synthesis of azido-propargyloxy derivatives of 1,3,5-triazine has been developed. The antibacterial activity against E. coli bacteria of propargyloxy substituted 1,3,5-triazines - 2,4,6-trispropargyloxy-1,3,5-triazine, 2-azido-4,6-bispropargyloxy-1,3,5-triazine and 2,4-diazido-6-propargyloxy-1,3,5-triazine and their hyperbranched polymers. It has been shown that the presence of an azide group in the compound directly affects the antibacterial activity. The cytotoxicity of these compounds against the M-HeLa, FetMSC and Vero cell lines was studied. The IC50 value was determined for low molecular weight compounds. It has been shown that hyperbranched polymers without azide groups don’t exhibit pronounced cytotoxicity and can be used in biomedical applications.

Thanks to several Vitis vinifera backcrosses with an initial V. vinifera L. × V. rotundifolia (previously Muscadinia rotundifolia) interspecific cross, the MrRUN1/MrRPV1 locus (resistance to downy and powdery mildews) was introgressed in genotypes phenotypically close to V. vinifera varieties. To check the consequences of introgressing parts of the V. rotundifolia genome on gene expression during fruit development, we conducted a comparative RNA-seq study on single berries from different V. vinifera cultivars and V. vinifera × V. rotundifolia hybrids, including ‘G5’ and two derivative microvine lines, ‘MV102’ (resistant) and ‘MV32’ (susceptible) segregating for the MrRUN1/RPV1 locus. RNA-Seq profiles were analyzed on a comprehensive set of single berries from the end of the herbaceous plateau to the ripe stage. Pair-end reads were aligned both on V. vinifera PN40024.v4 reference genome, V. rotundifolia cv ‘Trayshed’ and cv ‘Carlos’, and to the few resistance genes from the original V. rotundifolia cv ‘52’ parent available at NCBI. Weighted Gene Co-expression Network Analysis (WGCNA) led to classifying the differentially expressed genes into 15 modules either preferentially correlated with resistance or berry phenology and composition. Resistance positively correlated transcripts predominantly mapped on the 4-5 Mb distal region of V. rotundifolia chromosome 12 beginning with the MrRUN1/MrRPV1 locus, while the negatively correlated ones mapped on the orthologous V. vinifera region, showing this large extremity of LG12 remained recalcitrant to internal recombination during the successive backcrosses. Some constitutively expressed V. rotundifolia genes were also observed at lower density outside this region. Genes overexpressed in developing berries from resistant accessions, either introgressed from V. rotundifolia, or triggered by these in the vinifera genome, spanned various functional groups, encompassing calcium signal transduction, hormone signaling, transcription factors, plant–pathogen-associated interactions, disease resistance proteins, ROS and phenylpropanoid biosynthesis. This transcriptomic insight provides a foundation for understanding the disease resistance inherent in these hybrid cultivars and suggests a constitutive expression of NIR NBS LRR triggering calcium signaling. Moreover, these results illustrate the magnitude of transcriptomic changes caused by the introgressed V. rotundifolia background in backcrossed hybrids, on a large number of functions largely exceeding the ones constitutively expressed in single resistant gene transformants.

Rapid emergence of evasive SARS-CoV-2 variants is an on-going challenge for COVID-19 vaccinology. Traditional virus neutralization tests provide detailed datasets of neutralization titers against the viral variants. Such datasets are difficult to interpret and do not immediately inform on the sufficiency of the breadth of antibody response. Some of these issues could be tackled using the antigenic cartography approach. In this study, we created antigenic maps using neutralization titers of sera from donors who received Sputnik V booster vaccine after primary Sputnik V vaccination and compared them with the antigenic maps based on serum neutralization titers of Comirnaty-boosted donors. Traditional analysis of neutralization titers against WT, Alpha, Beta, Delta, Omicron BA.1 and BA.4/BA.5 showed a significant booster humoral response after both homologous (Sputnik V) and heterologous (Comirnaty) revaccinations against all the studied viral variants. However, despite this, a more in-depth analysis using antigenic cartography revealed that Omicron variants remain antigenically distant from WT, which is indicative of the formation of insufficient levels of cross-neutralizing antibodies. The implications of these findings may be significant when developing a new vaccine regimen.

Sialylated milk oligosaccharides (SMOs) is the most important oligosaccharides in human milk oligosaccharides (HMOs), and have a multifunctional health benefit, and the most abundant SMOs are sialyllactose (SLs). The previous studies indicate that the growth of tumor cells, and angiogenesis on tumor tissues with Lewis lung carcinoma, melanoma, and colon carcinoma cells could be prevented by SL. Thus, it has been proposed that SL might be an ideal candidate for the development of anti-angiogenic drugs without any side effects. It has been proposed that the Sialic acid (Sia) can be produced through SL’s hydrolysis, and the dietary Sia is further transported to the brain and other tissues though blood for formation of CMP-Sia, the activated precursor of Sia, and then is catalyzed by polysialyltransferases (polySTs) for synthesis of polysialic acid (polySia) or polysialylation of neural cell adhesion molecule (NCAM). Thus, it’s necessary to study and develop new inhibitors, which not only modulate a proper balance between the gut health and neuros system development, but also inhibit the overexpression of polySia, and thus block the tumor cell migration. In this study, we proposed that 3’-SL and 6’-SL may be more ideal inhibitors comparing with two previous inhibitors, the low molecular weight heparin (LMWH) and cytidine monophosphate (CMP) in the previous studies.

Vernonia amygdalina is an important nutritional and medicinal plant that is used to treat various diseases such as malaria and diabetes in Nigeria. In this study, we sequenced, assembled, and annotated the complete nucleotide sequence of the chloroplast genome of a V. amygdalina species isolated in Awka, Nigeria. The chloroplast genome is 153 149 bp in length and has a conserved structure that includes the LSC (84261 bp) region, the SSC (13152 bp) region, and the IR (27868 bp) regions. A total of 131 genes were identified, including 86 protein-coding genes, 37 tRNA genes, and 8 rRNA genes. Comparative analysis of the genome revealed species variations in the LSC region associated with the geographical location of the V. amygdalina plant. Phylogenetic analysis of the chloroplast genomes using FastTree showed that V. amygdalina clustered closest to the chloroplast of the Crepidiastrum genus. This study identifies the characteristics of the V. amygdalina chloroplast genome, which will improve our understanding of intraspecies diversity and the identification of potential molecular markers to determine geographical origin.

In the field of embedded systems, energy efficiency is a critical requirement, particularly for battery-powered devices. RISC-V processors have gained popularity due to their flexibility and open-source nature, making them an attractive choice for embedded applications. However, not all RISC-V processors are equally energy-efficient, and it is important to evaluate their performance in specific use cases. This paper evaluates the energy consumption and resource utilization of a new RISC-V processor, RisCO2, and four existing processors - Zero-riscy, Micro-riscy, Ri5cy, and CV32E40P - in a signal demodulation application for NDIR CO2 sensors. The processors were implemented in the PULPino SoC and synthesized using Vivado IDE. The processor named RisCO2 is based on the RV32E_Zfinx instruction set and was designed from scratch by the authors specifically for low-power signal processing applications such as signal demodulation in CO2 NDIR sensors. The other processors are Ri5cy, Micro-riscy, and Zero-riscy, developed by the PULP Platform team, and CV32E40P (derived from Ri5cy) from the OpenHW Group, all of them widely used in the RISC-V community. Our experiments showed that RisCO2 had the lowest energy consumption among the five processors, with a 53.5% reduction in energy consumption compared to CV32E40P and a 94.8% reduction compared to Micro-riscy. Additionally, RisCO2 had the lowest FPGA resource utilization compared to the best-performing processors, CV32E40P and Ri5cy, with a 46.1% and a 59% reduction in LUTs, respectively. Our findings suggest that RisCO2 is a highly energy-efficient RISC-V processor for NDIR CO2 sensors that require signal demodulation. The results also highlight the importance of evaluating processors in specific use cases to identify the most energy-efficient option. This paper provides valuable insights for designers of energy-efficient embedded systems using RISC-V processors.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is an enigmatic condition characterized by exacerbation of symptoms after exertion (post-exertional malaise or “PEM”), and by fatigue whose severity and associated requirement for rest are excessive and disproportionate to the fatigue-inducing activity. There is no definitive molecular marker or known underlying pathological mechanism for the condition. Increasing evidence for aberrant energy metabolism suggests a role for mitochondrial dysfunction in ME/CFS. Our objective was therefore to measure mitochondrial function and cellular stress sensing in actively metabolising patient blood cells. We immortalized lymphoblasts isolated from 51 ME/CFS patients diagnosed according to the Canadian Consensus Criteria and an age- and gender-matched control group. Parameters of mitochondrial function and energy stress sensing were assessed by Seahorse extracellular flux analysis, proteomics, and an array of additional biochemical assays. As a proportion of the basal oxygen consumption rate (OCR), the rate of ATP synthesis by Complex V was significantly reduced in ME/CFS lymphoblasts, while significant elevations were observed in Complex I OCR, maximum OCR, spare respiratory capacity, nonmitochondrial OCR and “proton leak” as a proportion of the basal OCR. This was accompanied by a reduction of mitochondrial membrane potential, chronically hyperactivated TOR Complex I stress signalling and upregulated expression of mitochondrial respiratory complexes, fatty acid transporters and enzymes of the β-oxidation and TCA cycles. By contrast, mitochondrial mass and genome copy number, as well as glycolytic rates and steady state ATP levels were unchanged. Our results suggest a model in which ME/CFS lymphoblasts have a Complex V defect accompanied by compensatory upregulation of their respiratory capacity that includes the mitochondrial respiratory complexes, membrane transporters and enzymes involved in fatty acid β-oxidation. This homeostatically returns ATP synthesis and steady state levels to “normal” in the resting cells, but may leave them unable to adequately respond to acute increases in energy demand as the relevant homeostatic pathways are already activated.

Plant-derived compounds have been historically used for the treatment of various diseases and an important source of several clinically useful anti-cancer agents. The Artemisia annua is known as a medicinal herb that is effective against cancer. Thus, the purpose of this study was to investigate whether ethanol extracts of Artemisia annua could increase an anti-cancer effect against LS174T cells. Our results show that Artemisia annua extracts (AAE) induces apoptosis through the regulation of mitochondria outer membrane potential. We demonstrate that apoptosis is induced by p53-dependent manner when cells were treated with Nutlin-3 (MDM2 inhibitor) and LY294002 (Akt inhibitor). In addition, the apoptotic effect was also observed in the p53-independent manner through pifithrin-α (p53 inhibitor) and celecoxib (COX-2 inhibitor) treatment. As in in vitro, AAE induced apoptotic effects and regulated apoptosis-related proteins in LS174T xenograft model. Taken together, these results suggest that Artemisia annua extracts exerts an anti-cancer effect through p53-independent manner, as well as p53-dependent manner by p53´ translocation in LS174T colon cancer cells.

(1) Background: in the context of sustainable development goals (SDGs), this work explores the repair direction of future cultivated land protection policies based on the Smith policy implementation model from the historical evolution to ensure that the cultivated land protection policy does not deviate during the implementation process. (2) Methods: this paper uses literature research and inductive deduction methods to sort out the evolution process of Chinese cultivated land protection policy, summarize the successful experience of transferring the focus of cultivated land protection in chronological order, and conclude the repair direction of Chinese cultivated land protection. (3) Results: although the Chinese cultivated land protection policy in the historical evolution has through three significant phases, there are still certain issues in the development trend of Chinese cultivated land protection policy based on regional division of labor for grain transportation and sales. (4) Conclusion: directly utilizing feedback from farmers as stakeholders will contribute to the maturity and improvement of cultivated land protection policies in the specific implementation of cultivated land protection policies.

Gravity-aided inertial navigation system (GAINS) is an important development in autonomous underwater vehicle (AUV) navigation. An effective path planning algorithm plays an important role in the performance of navigation in long-term underwater missions. By combining the gravity information obtained at each position with the error information from the INS, the posterior Cram\'er-Rao bound (PCRB) of GAINS is derived in this paper. The PCRB is the estimated lower bound of position variance for navigation along the planned trajectory. And the sum of PCRB is used as the minimum cost from the initial state to the current state in the state space, and the position error prediction variance of inertial navigation system (INS) is used as the minimum estimated cost of the path from the current state to the goal state in the A* algorithm. Thus, a path planning method with optimal navigation accuracy is proposed. According to simulation results, traveling along the path planed by the proposed method can rapidly improve the positioning accuracy while consuming just slightly more distance. Even when measuring noise changes, the planned path can still maintain optimal positioning accuracy, and high positioning accuracy is possible for any trajectory located within a certain range of the planned path.

Sentinel-2 can provide multi-spectral optical remote sensing images in RGBN bands with a spatial resolution of 10m, but the spatial details provided are not enough for many applications. WorldView can provide HR multi-spectral images less than 2m, but it is a commercial paid resource with relatively high usage costs. In this paper, without any available reference images, Sentinel-2 images at 10m resolution are improved to a resolution of 2.5m through super-resolution (SR) based on deep learning technology. Our model, named DKN-SR-GAN, uses degradation kernel estimation and noise injection to construct a dataset of near-natural low-high-resolution (LHR) image pairs, with only low-resolution (LR) images and no high-resolution (HR) prior information. DKN-SR-GAN uses the Generative Adversarial Networks (GAN) combined of ESRGAN-type generator, PatchGAN-type discriminator and the VGG-19-type feature extractor, using perceptual loss to optimize the network, so as to obtain SR images with clearer details and better perceptual effects. Experiments demonstrate that in the quantitative comparison of the non-reference image quality assessment (NR-IQA) metrics like NIQE, BRISQUE and PIQE, as well as the intuitive visual effects of the generated images, compared with state-of-the-art models such as EDSR8-RGB, RCAN and RS-ESRGAN, our proposed model has obvious advantages.

Unmanned surface vehicles have the advantages of maneuverability, concealment, wide activity area and low cost of use. Therefore, they have broad application prospects. This makes unmanned surface vehicles a research hotspot at home and abroad, and the sensing technology is the basis for the unmanned surface vehicles to perform tasks. The perception technology based on optical vision has the advantages of convenient application, relatively low cost, easy data acquisition and large amount of information, and has been widely studied by scholars at home and abroad. This paper mainly discusses the research of optical vision in unmanned surface vehicles from five aspects: Firstly, the water surface image preprocessing based on unmanned surface vehicles, mainly including water surface image stabilization research and defogging enhancement research; two water boundary detection; It is the use of light vision target detection; the fourth is the surface target tracking method. Finally, the light vision research of unmanned surface vehicles is summarized and forecasted.

Landslide is a sliding movement of rock mass, debris and soil along the slope under the action of gravity. Small Baseline Subset (SBAS) is an established method for the investigation and monitoring of landslide moments. This study focuses on monitoring the long-temporal displacement of mountainous terrain in Danba County, Sichuan Province via SBAS technique, based on 31 scenes of L-band ALOS/PALSAR data from Feb. 2007 to Oct. 2010.The results show that the largest velocity rates in LOS direction are ±120 mm/yr and maximum accumulated displacement is up to -300, which indicates fast movement of the mountainous terrain during the observation time. These results get good consistency against the results of previous study. This demonstrates the strong potential of SBAS technique for monitoring the landslides geohazard.

Many agricultural water uses crowd the river ecology of the river water, thus leading to irreversible habitat damage. This paper presents an agricultural economic loss calculation model that is based on river ecological basic flow (REBF) protection by introducing a typical crop water requirement coefficient. First, the water balance equation is used according to a set of REBF protection values to compute the agricultural water shortage that results in the REBF. Second, the agricultural water shortage that results in REBF protection and a typical crop water requirement coefficient are used to determine the food production generated by REBF protection. Finally, the loss of food production and the food market prices are used to determine the agricultural economic loss caused by the different protection levels of REBF. A case study of the Weihe River in China is conducted. The calculation model is used to compute the agricultural economic loss on the basis of REBF protection in the Baoji section of the Weihe River, and the change law of the agricultural economic loss that results in different levels of the REBF is discussed. In addition, changes in the canal water use coefficient and the crop structure that affect agricultural economic loss are analyzed. Results show that the spatial and temporal variations in the runoff affect the changes in time and space of the agricultural economic loss. The higher the REBF protection level, the higher the agricultural economic loss. In addition, agricultural economic loss can provide a quantitative basis for reasonable REBF protection. The size of agricultural economic loss helps the government sector in decision-making on REBF protection.

Global food security for the increasing world population not only requires increased sustainable production of food but a significant reduction in pre- and post-harvest waste. The timing of when a fruit is harvested is critical for reducing waste along the supply chain and increasing fruit quality for consumers. The early in field assessment of fruit ripeness and prediction of the harvest date and yield by non-destructive technologies have the potential to revolutionize farming practices and enable the consumer to eat the tastiest and freshest fruit possible. A variety of non-destructive techniques have been applied to estimate the ripeness or maturity but not all of them are applicable for in situ (field or glasshouse) assessment. This review focuses on the non-destructive methods which are promising, or have already been, applied to the pre-harvest in field measurement including colorimetry, visible imaging, spectroscopy and spectroscopic imaging. Machine learning and regression models used in assessing ripeness are also discussed.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

This project focuses on using machine learning classification algorithms to determine whether two people are 6 feet apart or not. Two Raspberry Pis were used simulate smart phones. RSSI values of the Bluetooth beacons transmitted between the Raspberry Pis were collected and recorded to train the classifier. The Gaussian Support Vector Machine Classifer yielded the highest testing accuracy of 79.670 and the Decision Tree Classifier yielded the highest AUC of 0.80.

Many biological functions of curcumin have been reported. As certain bioactivities of curcumin are eliminated by antioxidants, reactive oxygen species generated by curcumin have been suggested as a relevant mechanism. In the present study, effects of different types of antioxidants on stability and bioactivities of curcumin were analyzed. High concentrations (>4mM) of the thiol antioxidants including N-acetylcysteine (NAC), glutathione (GSH) and β-mercaptoethanol accelerated decomposition of curcumin and other curcuminoids; Submillimolar levels (<0.5 mM) of GSH and NAC rather improved their stability. Ascorbic acid or superoxide dismutase also stabilized curcumin regardless of their concentration. Cellular levels and bioactivities of curcumin including cytotoxicity and induction of heme oxygenase-1 were significantly reduced in the presence of 8 mM of GSH and NAC. The effects were enhanced in the presence of submillilmolar GSH and NAC, or non-thiol antioxidants. The present results indicate that antioxidants with reduced thiol group could directly interact with α, β-unsaturated carbonyl moiety of curcuminoids and modulate their stability and bioactivity.

Background: Despite advances in the treatment of hepatocellular carcinoma (HCC) over the last few decades, treatment opportunities for patients with HCC remain limited. HCC is the most common form of liver cancer, accounting for approximately 90% of all cases worldwide. Moreover, apart from the current pharmacological interventions, hepatic resection and liver transplantation are the mainstay curative approaches for patients with HCC. Methods: This systematic review included phase I, II, III, and IV clinical trials (CTs) and randomized controlled trials (RCTs) on current treatments for patients with HCC in an Asian population (2013–2023). A total of 427 articles were screened, and 184 non-duplicate publications were identified. After screening titles and abstracts, 96 publications were excluded, and another 28 were excluded after full-text screening. The remaining 60 eligible RCTs/CTs were finally included. Results: Sixty clinical trials fulfilled our inclusion criteria and screened 36 drugs as monotherapy or combination therapy for HCC. Most studies used sorafenib alone or in combination with any of the treatment regimens. Lenvatinib or atezolizumab with bevacizumab was used for HCC after initial sorafenib treatment. Eighteen studies compared the efficacy of sorafenib with that of other drugs, including lenvatinib, cabozantinib, tepotinib, tigatuzumab, linifanib, erlotinib, resminostat, brivanib, tislelizumab, selumetinib, and refametinib. Conclusion: This study provides comprehensive insights into effective treatment interventions for HCC in Asian populations. The overall assessment indicated that sorafenib alone or in combination with atezolizumab and bevacizumab has been the first treatment choice in the past decade to achieve better outcomes in patients with HCC in an Asian population

With correct dynamic system parameters (embodied in self-awareness statements), a controller can provide precise signals for tracking desired state trajectories. If dynamic system parameters are initially guessed incorrectly, a learning method may be used to find the correct parameters. In the deterministic artificial intelligence method, self-awareness statements are formed as mathematical expressions of the governing physics. When the nonlinear, coupled expressions are precisely parameterized as the product of known matrix components and unknown victrix (i.e., a regression form) tracking errors may be projected onto the known matrix to update the unknown victrix in an optimal form (in a two-norm sense). In this work, a modified learning method is proposed and proved to have global convergence of both state error and parameter estimation error. The modified learning method is compared with those in the prequels using simulation experiments of three-dimensional rigid body dynamic rotation motion. The modified approach is two magnitudes better than the methods in the prequels in terms of state error convergence.

Nonlinear ultrasonic testing has been accepted as a promising manner for evaluating material integrity in an early stage. Stress fatigue is the main threats to train safety, railways examinations for stress fatigue are more significant and necessary. A series of ultrasonic nonlinear wave experiments are conducted for rail specimens extracted from railhead with different degree of fatigue produced by three-point bent loading condition. The nonlinear parameter is the indicator of nonlinear waves for expressing the degree the fatigue. The experimental results show that the sensitivity of a third harmonic longitudinal wave is higher than second harmonic longitudinal wave testing. As the same time, collinear wave mixing shows strong relative with fatigue damages than a second longitudinal wave NDT method and provides more reliable results than third harmonic longitudinal waves nonlinear testing method.

The natural flavonoid epigallocatechin gallate (EGCG) has a wide range of biological activities including binding to nucleic acids; however, mechanisms of interaction of EGCG with DNA organized in chromatin have not been systematically studied. In this work, interaction of EGCG with chromatin in cells, and with nucleosomes and chromatosomes in vitro was studied using fluorescent microscopy and single particle Förster resonance energy transfer approaches, respectively. EGCG effectively penetrates into the nuclei of living cells and binds to DNA there. Interaction of EGCG with nucleosomes in vitro induces large-scale, reversible uncoiling of nucleosomal DNA that occurs without dissociation of DNA or core histones at sub- and low-micromolar concentrations of EGCG. EGCG does not reduce the catalytic activity of poly(ADP-ribose) polymerase 1 (PARP1), but causes modulation of the structure of the PARP1-nucleosome complex. EGCG significantly changes the structure of chromatosomes, but does not cause dissociation of the linker histone. Reorganization of nucleosomes and chromatosomes by EGCG might facilitate access of protein factors involved in DNA repair, replication and transcription to DNA and thus might contribute to the modulation of gene expression by EGCG that was reported earlier.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Curcumin, a polyphenol with a rich history spanning two centuries, has emerged as a promising therapeutic agent targeting multiple signaling pathways and exhibiting cellular-level activities that contribute to its diverse health benefits. Extensive preclinical and clinical studies have demonstrated its ability to enhance the therapeutic potential of various bioactive compounds. While its reported therapeutic advantages are manifold, predominantly attributed to its antioxidant and anti-inflammatory properties, its efficacy is hindered by poor bioavailability stemming from inadequate absorption, rapid metabolism, and elimination. To address this challenge, nano-delivery systems have emerged as a promising approach, offering enhanced solubility, biocompatibility, and therapeutic effects for curcumin. We have analyzed the knowledge on curcumin nano-encapsulation and its synergistic effects with other compounds, extracted from electronic databases. We discuss the pharmacokinetic profile of curcumin, current advancements in nano-encapsulation techniques, and the combined effects of curcumin with other agents across various disorders. By unifying existing knowledge, this analysis intends to provide insights into the potential of nano-encapsulation technologies to overcome constraints associated with curcumin treatments, emphasizing the importance of combinatorial approaches in improving therapeutic efficacy. Finally, this compilation of study data aims to inform and inspire future research into encapsulating drugs with poor pharmacokinetic characteristics and investigating innovative drug combinations to improve bioavailability and therapeutic outcomes.

Background: Although antiretroviral therapy (ART) effectively halt disease progression in HIV infections, complete eradiation of the virus remains elusive. Additionally, challenges such as long-term ART toxicity, drug resistance, and the demanding regimen of daily and lifelong ad-herence required by ART highlight the imperative need for alternative therapeutic and preventa-tive approaches. In recent years, broadly neutralizing antibodies (bNAbs) have emerged as promising candidates, offering potential for therapeutic, preventative and possibly curative in-terventions against HIV infection. Objective: This review aims to provide a comprehensive overview of the current state of knowledge regarding the passive immunization of bNAbs in HIV-1 infected individuals. Main findings: Recent findings from clinical trials have highlighted the potential of bNAbs in treatment, prevention, and in the quest of an HIV-1 cure. While monotherapy with a single bNAb is insufficient in maintaining viral suppression and preventing viral escape, ultimately leading to viral rebound, combination therapy with potent, non-overlapping epitope-targeting bNAbs have demonstrated prolonged viral suppression and delayed time to rebound by effec-tively restricting the emergence of escape mutations, albeit largely in individuals with bNAb-sensitive strains. Additionally, passive immunization of bNAb have provided ‘proof-of-concept’ for antibody-mediated prevention against HIV-1 acquisition, although com-plete prevention was not obtained. Therefore, further research on the use of bNAbs in HIV-1 treatment and prevention remains imperative.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V-microalloying 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure was consisted of ferrite, RA and secondary martensite (SM) after subjected to SPA process. (V, Mo)C with disc-like morphology mainly precipitated during intercritial tempering, and the aspect ratio of particle decreased, leading to the appearance of near-spherical morphology. After subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: out layer of ferrite, interlayer of SM and inner layer RA) enabled high yield strength of 1097 MPa, total elongation of 14%, and impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated about 108 MPa.

The powdered sorbents were applied in a batch system under "static" conditions and showed a much higher adsorption capacity than the granular one. These type of sorbents are more suitable for small quantities of water with a high concentration of arsenic. The possibilities of using all the tested methods for arsenic removal have been evaluated, and a scheme of the technological process has been proposed.

The present work was aimed at the investigation of effect of High Energy Ball Milling (HEBM) time on the sintering kinetics, structure, and properties of heavy tungsten alloy (HTA) W-7%Ni-3%Fe. The HTA samples were obtained from the nanopowders (20-80 nm) by conventional liquid phase sintering (LPS) in hydrogen and by Spark Plasma Sintering (SPS) in vacuum. The HTA density was shown to depend on the HEBM time non-monotonously that originates from the formation of non-equilibrium solid solutions in the W-Ni-Fe systems during HEBM. The SPS kinetics of the HTA nanopowders was shown to have a two-stage character, the intensity of which depends on the Coble diffusion creep rate and on the intensity of diffusion of the tungsten atoms in the crystal lattice of the -phase. The kinetics of sintering of the initial submicron powders have a single-stage character originating from the intensity of the grain boundary diffusion in the -phase. The dependencies of the hardness and of the yield strength on the grain sizes were found to obey the Hall-Petch relation. The hardness, strength, and dynamic strength in the compression tests of the fine-grained tungsten alloys obtained by SPS and LPS were studied.

The concept of targeted drug delivery can be described in terms of the drug’s ability to mimic the other biological objects’ property to localize to target cells or tissues. For example, drug delivery systems based on red blood cells or mimicking some of their useful features, such as long circulation in stealth mode, have been known for decades. On the contrary, therapeutic strategies based on macrophages have gained very limited attention until recently. Here we review two biomimetic strategies associated with macrophages, that can be used to develop new therapeutic modalities: First, the mimicry of certain types of macrophages (i.e., the use of macrophages, including tumor-associated, or macrophage-like particles as a carrier for targeted delivery of therapeutic agents); and Second, the mimicry of ligands, naturally absorbed by macrophages (i.e., the use of therapeutic agents specifically targeted at macrophages). We discuss potential applications of biomimetic systems involving macrophages for the new advancements in treatment of infections, inflammatory diseases, and cancer.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

Microfluidic devices have been extensively investigated in recent years in fields including ligand-binding analysis, chromatographic separation, molecular dynamics, and DNA sequencing. To prolong the observation of a single molecule in aqueous buffer, the solution in a sub-micron scale channel is driven by the electric field and reversed after a fixed delay following each passage, so that the molecule passes back and forth through the laser focus and the time before irreversible photobleaching is extended. However, this practice requires complex chemical treatment to the inner surface of the channel to prevent unexpected sticking to the surface and the confined space renders features, such as a higher viscosity and lower dielectric constant, which slow the Brownian motion of the molecule compared to the bulk liquid. In this paper, we have fixed a capillary microchannel with an inner diameter of 2 microns on top of a piezo stage to recycle the molecule and collected the fluorescence by a confocal microscope. The passing times of the molecule through the laser focus are calculated by a real-time control system based on an FPGA and the commands of translation are given to the piezo stage through a feedback algorithm. We have achieved a maximum number of recycles of more than 200 and developed a maximum-likelihood estimation of the diffusivity of the molecule, which attains results of the same magnitude as previous reports. This technique simplifies the overall procedure of the single-molecule recycling and could be useful for the ligand-binding studies of biomolecules.

A large amount of accurate river cross-section data is indispensable for predicting river stages. However, the measured river cross-section data are usually sparse in the transverse direction at each cross-section as well as in the longitudinal direction along the river channel. This study presents three algorithms to resample the river cross-section data points in both the transverse and longitudinal directions from the original data. The resampled cross-section data based on the linear interpolation satisfactorily maintains the topographic and morphological features of the river channel, especially in the meandering river segment. A two-dimensional (2D) high-resolution unstructured-grid hydrodynamic model was used to assess the performance of the original and resampled cross-section data on a simulated river stage under low flow and high flow conditions. The simulated river stages are significantly improved using the resampled cross-section data based on the linear interpolation in the tidal river and non-tidal river segments. Furthermore, the performance of the 2D and three-dimensional (3D) models on the simulated river stage was also evaluated using the resampled cross-section data. The results indicate that the 2D and 3D models reproduce similar river stages in both tidal and non-tidal river segments under the low flow condition. However, the 2D model overestimates the river stages in both the tidal and non-tidal river segments compared to the 3D model under the high flow condition. The model sensitivity was implemented to investigate the influence of bottom drag coefficient and vertical eddy viscosity on river stage. The results reveal that bottom drag coefficient has a minor impact on river stage, but the vertical eddy viscosity is insensitive to river stage.

The use of analytical techniques is important and critical in all areas of REE research such as exploration, mining, extraction, and metallurgical activities at different stages. At every stage of these activities, rock, ore, mineral, and other related materials have to be analysed for their REE contents in terms of elemental, isotopic, and mineralogical concentrations using different analytical techniques. Spectacular developments have taken place in the area of analytical instrumentations during the last four decades, with some of them having shrunk in size and become hand-held. Among laboratory-based techniques, F-AAS, GF-AAS, ICP-OES, and MP-AES have become very popular. Because of high sensitivity, less interference effects, and ease of use. ICP-MS techniques such as quadrupole-ICP-MS, ICP-MS/MS, ICP-TOF-MS, MH-ICP-MS, HR-ICP-MS, and MC-ICP-MS, with both solution nebulisation as well as direct solid analysis using laser ablation sample introduction methods, have become extremely popular for REE analysis. For direct analysis of solids INAA, XRF, and LIBS techniques besides LA-based ICP-MS techniques are being extensively utilised. LIBS technique in particular requires little to no sample preparation. TIMS, SIMS, and SHRIMP techniques are being used for isotopic as well as dating REE depots. Portable analytical techniques such as pXRF, pLIBS, and Raman spectrometers are able to do in situ analysis even in the field helping to take fast decisions during exploration studies. At present hyperspectral remote sensing techniques including hand-held, drone, and satellite-based techniques have become very popular in REE exploration studies because of their ability to cover larger areas in a limited time and thus became very cost-effective. Deployment of microanalytical devices/sensors mounted in remotely operated vehicles (ROV) is being successfully utilized in detecting REE-rich deposits in the deep oceans. Providing updated in-depth information on all these important aspects with suitable examples, especially from the point of view of REE research studies is the focal point of this review article.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Laminate structures composed of stiff plates and thin soft interlayers are widely used in aerospace, automotive and civil engineering encouraging the development of reliable non-destructive strategies for their condition assessment. In the paper, elastodynamic behaviour of such laminate structures is investigated with emphasis on its application in ultrasonic based NDT and SHM for the identification of interlayer mechanical and interfacial contact properties. A particular attention is given to the practically important frequency range, in which the wavelength considerably exceeds the thickness of the film. Three layer model with spring-type boundary conditions employed for imperfect contact simulation is used for numerical investigation. Novel effective boundary conditions are derived via asymptotic expansion technique and used for analysis of the peculiar properties of elastic guided waves in considered laminates. It is revealed that the thin and soft film influences the behaviour of the laminate mainly via the effective stiffnesses being a combination of the elastic moduli of the film, its thickness and interface stiffnesses. To evaluate each of these parameters separately (or to figure out that the available experimental data are insufficient), a step-wise procedure employing the effective boundary conditions is proposed and tested versus the laser Doppler vibrometry data for Lamb waves in Aluminium/Polymer film/Alumunium structure. The possibility of using film-related thickness resonance frequencies to estimate the film properties and contact quality is also demonstrated. Additionally, the rich family of edge waves is also investigated, and the splitting of fundamental edge waves into pairs is revealed.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

In this paper, we explore the black hole solutions with the rainbow deformed metric in the presence of the exponential form of the nonlinear electrodynamics with asymptotic Reissner- Nordstr ̈om properties. We calculate the exact solution of metric function and explore the geometri- cal properties in the background of massive gravity. From the obtained solution, the existence of the singularity is confirmed in proper limits. Using the solutions we also investigate the thermodynamic properties of the solutions by checking the validity of the first law of thermodynamics. Continuing the thermodynamic study, we investigate the conditions under which the system is thermally stable from the heat capacity and the Gibbs free energy. We also discuss the possible phase transition and the criticality of the system. It was found that the quantum gravitational effects of gravity’s rain- bow render the thermodynamic system stable in the vicinity of the singularity. Hence, we obtained a first order phase transition which is interpreted as the large/small black hole phase transition. From the equation of state it was found that after diverging at the singularity, the system evolves asymptotically into pressure-less dust as one moves away from the central singularity. We also calculated the quantum work using the change of the Helmholtz free energy.

The monitoring of river discharge is vital for the correct management of water resources. A worldwide facility used for measuring discharge are flat-V gauging weirs. These structures consist of a small weir, with a triangular cross-section and a flat “V”-shaped notch. Their extensive use is a consequence of their utility in the measurement of both low and high flow conditions. However, depending on their size, local morphology and river discharge can act as full or partial hydraulic barriers to fish migration. To give answer to this question, the present work studies fish passage performance over flat-V weirs considering their hydraulic performance. For this, radio-tracking and video monitoring observations were combined with computational fluid dynamics (CFD) models in two flat-V weirs, using Iberian barbel (Luciobarbus bocagei) as target species. Results show that fish passage is conditioned by both hydraulic and behavioral processes, providing evidences about the scenarios where flat-V weirs may act as full or partial barriers to upstream movements. For the studied flat-V weirs, a discharge range of 0.27-8 m3/s, with a water drop difference between upstream and downstream water levels lower than 0.7 m and a depth downstream the weir higher than 0.30 m can be considered as an effective passage situation for barbels. These findings are of interest to quantify flat-V weir impacts, for engineering applications and to establish managing or retrofitting actions when required.

Fe- and Al-rich metapelite from the Transangarian segment of the Yenisey Ridge (East Siberia, Russia) is a potential new source of high-alumina refractories. The rocks have relatively high average contents of Al2O3 (20 wt.%) and Fe2O3 (7.91 wt%), moderate K2O (3.44 wt%), and low CaO (0.74 wt%). Their dominant mineral assemblages are andalusite + muscovite + margarite + chlorite + biotite + quartz or staurolite + kyanite or/and andalusite + chlorite + muscovite + biotite + quartz with ±garnet and ±plagioclase. Al2SiO5 polymorphs occur as up to 1.5 cm andalusite porphyroblasts and partial or complete pseudomorphs after andalusite (kyanite and staurolite). Accessories include abundant Fe-Ti oxides and sporadic REE-, Y-, Ca-phosphates; sulfides are negligible. The composition of Al2SiO5 concentrates obtained in laboratory by heavy-media and magnetic separation from ≥0.06 mm fractions meet all requirements for raw material of this type: &gt;56 wt% Al2O3, &lt;42 wt% SiO2, &lt;1 wt% Fe2O3, &lt;1.2 wt% TiO2, and &lt;0.2 wt% (CaO+MgO). The andalusite, kyanite, and mixed ores yield 0.7-4.1 wt%, 0.7-2.2 wt%, and 1.9-6.0 wt% of concentrate, respectively. The best-quality ores rich in Al2SiO5 polymorphs reside in zones of contact and/or dynamic metamorphism superimposed over regional metamorphism of Al-rich rocks.

Pluripotent stem cells (PSCs) can differentiate into three germ layers and diverse autolo-gous cell lines. Being among the most commonly used large domesticated hoofed animals and serving as a vital source of food and bioreactors, cattle are among the many species in which PSCs have been developed. Bovine PSCs (bPSCs) are the "seed cells" of regenerative science and have immense potential to advance species propagation, genetic engineering, and disease treatment. Moreover, they can aid in screening new drugs for efficacy and toxicity, model human diseases, and establish a sustainable agricultural system that can cater to the needs of the growing global population. Establishing stable bPSCs in vitro has been a critical scientific challenge, and researchers have made numerous attempts to address this issue. This review primarily delves into the current research progress of bPSCs, the challenges faced, and their potential applications.

The Yb/Al multilayer films exhibit excellent theoretical reflectivity in the 54-90nm wavelength range. This study attempted to incorporate 1.5% wt.% of Si impurities into Al to suppress the crystallization of Al, reduce interfacial roughness, and enhance the actual reflectivity of the prepared Yb/Al multilayer films. The internal microstructure changes of the film layers before and after Si impurity doping were investigated using GIXRR, AFM, and XRD techniques. The reflectivity of two types of multilayer films, Yb/Al(1.5wt.%Si) and Yb/Al(pure), was tested to evaluate the effect of Si impurity on the film performance.

The study is based on the results of long-term field studies, satellite and aerial data analysis. In the maximum of the Little Ice Age (LIA) 243 glaciers with a total area of 353.4 km2 were reconstructed. By the results of interpretation of Corona images by 1968 the number of glaciers increased (236), the total area reduced to 242 km2. In 2010 glaciation was represented by 237 glaciers with a total area of 201 km2. Thus, from the maximum of the LIA, the glaciation of the Tavan-Bogd mountains decreased by 43%, which is somewhat less than the neighboring glacial centers (Ikh-Turgen, Tsambagarav, Tsengel-Khayrkhan and Mongun-Taiga mountains). The probable cause is the predominance of larger glaciers relatively resistant to warming and higher altitudes. The effect of glacier size on their stability is supported by differences in the relative shrinkage of glaciers in different parts of the Tavan-Bogdo-Ola massif: the smallest decline occurred in the basins of the Tsagan-Gol (31.7%) and Sangadir (36.4%) rivers where the largest glaciers are located. On the contrary, on the lower periphery of the massif, where small glaciers predominate, the relative reduction was large (74-79%). On the background of the general retreat trend large valleys glaciers retreated faster in 1968-1977 and after 2010. In 1990-s the retreat was slow. After 2010 the glacial retreat was extremely fast. The retreat of glaciers in the last 50-60 years was caused by a trend towards a decrease in the amount of precipitation until the mid-1970s and a sharp warming in the 1990s and early 2000s.

Nowadays there is a need to increase the density of interconnections on printed circuit boards (PCBs). Does this mean that the only way out for quality PCB manufacturing is to proportional increase in precision of equipment, or is there another way? One of the main constraints to increasing the density of PCB interconnections is the transition holes. As the number of conductive layers increases, the number of vias increases and they cover a significant space on the PCB. On the other hand, reducing the size of the vias is limited by the capability of spatial alignment of the PCB stack during manufacturing. There are standards that set limits for the design of contact pads on a PCB (IPC-A-600G, IPC-6012B). However, depending on the precision of production, the contact pads may be of poor quality. This raises the issue of determining the reliability of a contact pad with defined parameters at the design stage, taking into account manufacturing capabilities. This research proposes an analytical method for evaluation of reliability of a via or plated through-hole based on calculation of its probability of production in accordance with the current standards. On the basis of the method a model was developed both for the case of a contact pad without any conductors connected to it (nonfunctional contact pad) and for the real case with a connected conductor. The model estimates the probability of making an acceptable via for a given reliability class depending on parameters such as the conductor width (minimum permissible and usable), drilled hole diameter and pad diameter, as well as the accuracy of the drilling operation. The analysis of the modeling results showed that for the real case, a reduction in the reliability class would insignificantly affect the probability of making an acceptable via due to the tight limitation on the connection place of the conductor and the contact pad. In conclusion, we propose an algorithm for determining the optimal parameters of teardrops to minimize the negative impact of the conductor on the reliability of the vias.

RISC-V offers a modular technical approach combined with an open, royalty-free instruction set architecture (ISA). This openness allows various researches to incorporate RISC-V into both open and proprietary solutions or services. However, despite its advantages as a fundamental building block for many embedded systems, the escalating complexity and functional demands of real-time applications have made adhering to response time deadlines challenging. This has led to an increased demand for comprehensive development insights for real-time systems based on RISC-V. To improve development efficiency, we offer a detailed performance analysis of RISC-V in comparison to various ISAs. In this paper, we analyze the real-time performance of RISC-V through two real-time approaches based on processor architectures. For RTOS applications, we adopted FreeRTOS and evaluated its performance on HiFive1 Rev B (RISC-V) and STM3240G-EVAL (ARM M) to evaluate real-time performance. For Real-time Linux, we utilized Linux with the Preempt-RT patch and tested its performance on VisionFive 2 (RISC-V), MIO5272 (x86-64), and Raspberry Pi 4 B (ARM A). Through these experiments, we examined the real-time mechanism of each operating system. Additionally, in the Preempt-RT experiments, scheduling latencies were evaluated using cyclictest. Finally, in order to practically show the real-time capabilities of RISC-V, we implemented motion control of a six-axis collaborative robot, which was performed on the VisionFive 2 platform. This implementation provided a comparative result of RISC-V’s performance against the x86-64 architecture of MIO-5272. Ultimately, the results indicated that the real-time performance of RISC-V for real-time applications was slightly inferior to that of the x86-64 architecture. A noticeable achievement of this research was the first implementation of an EtherCAT Master on RISC-V designed for real-time applications featuring a multi-tasking structure. The research offers valuable insights into the real-time capabilities of RISC-V compared to established architectures like x86-64. While RISC-V might not surpass these architectures in real-time performance, its flexibility, modularity, and open nature make it a compelling choice for a wide range of real-time applications. The successful implementation of the EtherCAT Master on RISC-V further expands its potential in the domain of real-time embedded control systems.