Serial femtosecond crystallography (SFX) using an X-ray free-electron laser (XFEL) enables determination of room-temperature structures without causing radiation damage. Using an optical pump-probe or mix-and-injection, SFX enables the intermediate state visualization of a molecular reaction. In SFX experiments, serial and stable microcrystal delivery to the X-ray interaction point is vital for reasonable data collection and efficient beam time. The Pohang Accelerator Laboratory X-ray Free Electron Laser (PAL-XFEL) facility established SFX instruments at a nanocrystallography and coherent imaging (NCI) experimental station. Various sample delivery methods, including injection, fixed-target scanning, and hybrid methods, have been developed and applied to collect XFEL diffraction data. Herein, we review the currently available sample delivery methods for SFX at the NCI experimental station at the PAL-XFEL. This article will help PAL-XFEL users access the SFX system for their experiments.

This paper presents a 32 GHz high power amplifier (HPA) with a design strategy to achieve a high-power output with reliable operation for the Ka-band deep space satellite communication in 150 nm GaN HEMT technology. The presented Ka-band HPA employs a cascaded two-stage common source amplifier topology, and the output stage is comprised of an 8-way power combining network in current mode. The interstage matching network is designed with the bandpass configuration utilizing capacitors and transmission lines to provide better stability at the low-frequency regime. The implemented Ka-band HPA achieved a peak power gain of 7.3 dB at 32 GHz and a 3 dB bandwidth was 3.5 GHz between 31.3 and 34.8 GHz. The saturated output power at the peak power added efficiency (PAE) of 19.3% was 38.2 dBm, and the output 1 dB gain compression point (OP1dB) was 27.4 dBm in the measurement. The designed HPA consumes an area of 19.35 mm^2 including RF signal, and DC pads

Decapod assemblages in Zostera marina beds from two bays adjacent to unvegetated habitats were investigated to assess their influence on decapod assemblages. Thirty-eight decapod species belonging to 4 taxa were collected using a small beam trawl at four habitat types from two different locations off the coast of Namhae Island, southern Korea. Dominant decapod taxon at all habitats was the caridean shrimps, with Eualus leptognathus, Heptacarpus pandaloides, Latreutes anoplonyx, La. laminirostris and Palaemon macrodactylus being the most abundant caridean species. Crabs were characterized by the highest biomass, but moderate species richness and abundance. Penaeoids and sergestoids shrimps only accounted for <1% of the total decapod abundance. The number of species, their abundance, and the diversity of decapod assemblages varied greatly by habitat type, season, and diel patterns. Species number and abundance peaked in seagrass beds of southern exposed bays during the autumn, and were lowest in unvegetated habitats during the summer months. Diel decapod species and catch rates were higher at night. Dense seagrass vegetation and nighttime supported greater decapod species richness and higher mean densities, but not diversity. Multivariate analyses revealed that habitat type and season significantly affected the structure of decapod assemblages, but diel patterns had a minor influence. Among decapod species, Pa. macrodactylus and Pugettia quadridens characterized the decapod assemblages in seagrass beds at the northern semi-closed bay, while Telmessus acutidens, Crangon affinis, Cr. hakodatei, Charybdis japonica and Portunus sanguinolentus were significantly associated with both vegetated and unvegetated habitats at the southern exposed bay, with the former two species more abundant during winter and spring.

Prostate cancer (PCa) used to be one of the most common nondermatologic cancers in men that can be treated only with surgery. However, a revolutionary breakthrough came in the 1980s with the introduction of long-acting luteinizing hormone-releasing hormone (LHRH) agonists for the cu-rative treatment of PCa. This paradigm shift contributed to the combined use of androgen depri-vation therapy (ADT), chemotherapy, and radiotherapy for the treatment. The latest data high-light the use of treatment intensification (TI), i.e., combined use of radiotherapy (RT) and hormo-nal or drug treatments, for localized or locally advanced PCa. Indeed, the results of combined modality treatments have shown a reduction in disease-specific mortality and improved overall survival. Although TI seems promising, more research studies are warranted to confirm its effi-cacy. This review summarizes the latest available outcome results of pivotal trials and clinical studies on the efficacy of TI.

Voice spoofing attempts to break into a specific automatic speaker verification (ASV) system by forging the user’s voice, and can be used through methods, such as text-to-speech (TTS), voice conversion (VC), and replay attacks. Recently, deep learning-based voice spoofing countermeasures have been developed. however, the problem with replay is that it is difficult to construct a large number of datasets because it requires a physical recording process. To overcome these problems, this study proposes a pre-training framework based on multi-order acoustic simulation for replay voice spoofing detection. Multi-order acoustic simulation utilizes existing clean signal and room impulse response (RIR) datasets to generate audios, which simulate the various acoustic configurations of the original and replayed audios. The acoustic configuration refers to factors, such as the microphone type, reverberation, time delay, and noise that may occur between a speaker and microphone during the recording process. We assume that a deep learning model trained on an audio that simulates the various acoustic configurations of the original and replayed audios can classify the acoustic configurations of the original and replay audios well. To validate this, we performed pre-training to classify the audio generated by the multi-order acoustic simulation into 3 classes: clean signal, audio simulating the acoustic configuration of the original audio, and audio simulating the acoustic configuration of the replay audio. We also set the weights of the pre-training model to the initial weights of the replay voice spoofing detection model using the existing replay voice spoofing dataset and then performed fine-tuning. To validate the effectiveness of the proposed method, we evaluated the performance of the conventional method without pre-training and proposed method using an objective metric, i.e., the accuracy. As a result, the conventional method achieved 92.94% accuracy and proposed method achieved 98.16% accuracy.

We evaluated the association of blood pressure with blood levels of cadmium, lead, and cadmium and lead together (cadmium+lead) in a representative sample of adolescents from Korea by use of 2010-2016 data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study enrolled adolescents aged at 10-18 years-old who completed a health examination survey and had blood measurements of lead and cadmium. The association of adjusted mean differences in diastolic and systolic blood pressure with doubling of blood lead and cadmium were estimated by regression of blood pressure against log₂-transformed blood metals and their quartiles after covariate adjustment. Adjusted odds ratios for prehypertension were calculated for log₂-transformed blood levels of lead and cadmium and their quartiles. Our analysis of adolescents in Korea indicated that blood levels of lead and cadmium were not significantly associated with increased blood pressure or risk of pre-hypertension. However, the cadmium+lead level was associated with pre-hypertension. Previous studies showed that blood levels of lead and cadmium were associated with increased blood pressure and risk of hypertension in adult populations. We found no such effect in Korean adolescents, although the cadmium+lead level was associated with prehypertension. These differences may be because adolescents generally have lower levels of these blood metals or because adolescents only rarely have hypertension.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

Bovine mastitis (BM) has been causing great economic and financial losses in the dairy industry worldwide and one of its major pathogenic agents is S. aureus. BM treatment still relies on antibiotics. The extensive use of antimicrobials gives rise to bacterial strains such as methicillin-resistant S. aureus (MRSA) and mupirocin-resistant S. aureus (MuRSA). This study aimed to investigate and compare the prevalence of MRSA and MuRSA and antimicrobial susceptibility in S. aureus isolates from bovine mastitis milk in conventional and organic dairy farms. Milk samples were taken from mastitis-infected cattle in 6 conventional and 7 organic dairy farms from South Korea. According to the Food Codex, 163 suspected S. aureus colonies were isolated from the pooled milk samples from each farm. Further rapid coagulase test confirmed 11 out of 74 isolates from 4 conventional farms (CF1, CF2, CF3, CF4) while 17 out of 89 isolates from 3 organic farms (OF1, OF2, OF3) exhibited coagulase activity. Multiplex PCR amplification showed that the nuc gene marker for S. aureus was found in all coagulase-positive isolates from OF 1 and at least one isolate from CF1, CF2, CF3, and CF4. Conversely, only 2 isolates from CF2 contained mecA gene for MRSA while none had the mupA gene for MuRSA. Antimicrobial susceptibility testing revealed that conventional farm isolates were more resistant to antibiotics particularly, against ampicillin and tetracycline, and, in turn, could imply a potential to develop multidrug resistance if stringent measures to control antimicrobial use in dairy farms is not implemented properly.

In order to reduce the large damage caused by train derailment, protective facilities of various shapes and conditions can be installed on railroad tracks. These protective facilities are referred to as derailment containment provisions (DCPs) and three different types are used worldwide. However, there are no clear standards for DCPs design such as installation location, size, and design load, and performance verification of DCPs installed in the actual railway field is not sufficiently performed. In this paper, the functionality of DCPs is analyzed through the full-scale derailment test. In order to propose a method for estimating the collision load acting on the DCP type I after derailment, the experimental results and simulation results are compared. The function of DCP type I according to the change of the vehicle's center of gravity is identified through comparative analysis of the post derailment behavior.

Background: This study investigated the prevalence of worsening problems using Post Stroke Checklist (PSC) at 3, 6, and 12 months post-stroke and their associations with health-related quality of life. Methods: In stroke patients admitted between June 2014 and December 2015, PSC and EuroQol-5Dthree level (EQ-5D-3L) were assessed at post-stroke 3 (n=181), 6 (n=175), and 12months (n=89). The prevalence of worsening problems and its association withEQ-5D-3L at post-stroke 3 and 6months were analyzed. Results: An average of 0.59 (range 0–12), 1.47 (range 0–12), and 1.00 (range 0–10) worsening problems per patient was identified at 3, 6, and 12months after stroke, respectively. The most frequently and continuously identified worsening problems were mood disturbances (reported by 8.8%, 16.0% and13.5% of patients at 3, 6, and 12 months post-stroke, respectively). Worsening mobility was significantly associated with worse EQ-5D index at post-stroke 3 months (β,-0.583; 95% CI, -1.045 to -0.120). The worsening of mobility and communication was significantly associated with worse EQ-5D index at post-stroke 6 months (mobility: β,-0.170; 95% CI, -0.305 to -0.034, communication: β,-0.164; 95% CI, -0.309 to -0.020). Conclusions: PSC may be useful for the detection of various subjective worsening problems during serial clinical follow-up after stroke. Appropriate rehabilitation and management strategy to solve the identified problems could improve the quality of life in stroke survivors.

Citrus peel has been used in Asian traditional medicine for the treatment of cough, asthma, and bronchial disorders. However, the anti-inflammatory effect of quercetogetin (QUE), a polymethoxylated flavone isolated from the peel of citrus unshui is poorly understood. We investigated the anti-inflammatory effect and the molecular mechanisms of QUE in lipopolysaccharide (LPS)-induced RAW264.7 cells. QUE inhibited the production of NO and prostaglandin E2 by suppressing the LPS-induced expression of inducible nitric oxide synthase and cyclooxygenase-2 at both the mRNA and protein levels. QUE suppressed the production of proinflammatory cytokines, such as interleukin (IL)-1β, IL-6, and tumor necrosis factor-α. QUE also inhibited the translocation of the nuclear factor kappa B subunit, p65, into the nucleus by interrupting the phosphorylation of IκB-α in LPS-induced RAW 264.7 cells. Based on the finding that QUE significantly decreased p-ERK protein expression in LPS-induced RAW264.7 cells, we confirmed that suppression of the inflammatory process by QUE was mediated through the MAPK pathway. This is the first report on the strong anti-inflammatory effects of QUE, which is a compound that can potentially be used as a therapeutic agent for inflammatory diseases.

This study aimed to compare the efficacies and safety of enhanced and standard monofocal intraocular lenses (IOLs) in eyes with early glaucoma. Patients with concurrent cataracts and open-angle glaucoma (OAG) were enrolled. They underwent cataract surgery with IOL implantation. Manifest refraction; monocular uncorrected distance visual acuity (UDVA), corrected distance visual acuity (CDVA), uncorrected intermediate visual acuity (UIVA), and uncorrected near visual acuity (UNVA); visual field (VF); contrast sensitivity (CS); defocus curves and questionnaires were assessed three months postoperatively. Thirty-four and 38 patients had enhanced and standard monofocal IOLs, respectively. The enhanced monofocal IOL provided better UIVA than the standard monofocal IOL (p = 0.003) but similar UDVA, CDVA and UNVA. The enhanced monofocal IOL had more consistent defocus curves than the standard monofocal IOL, especially at -1 (p = 0.042) and -1.5 (p = 0.026) diopters. The enhanced monofocal IOL provided better satisfaction (p = 0.019) and lower spectacle dependence (p = 0.004) than the standard monofocal IOL for intermediate vision, with similar VF and CS. In conclusion, the enhanced monofocal IOL is recommended for patients with OAG because they provide better intermediate vision, higher satisfaction, and lower dependence on spectacles than standard monofocal IOL, without worsening other visual outcomes.

Cellular response to mechanical stimuli is an integral part of cell homeostasis. The interaction of the extracellular matrix with the mechanical stress plays an important role in cytoskeleton organisation and cell alignment. Insights from the response can be utilised to develop cell culture methods that achieve predefined cell patterns, which are critical for tissue remodelling and cell therapy. We report the working principle, design, simulation and characterisation of a novel electromagnetic cell stretching platform based on the double-sided axial stretching approach. The device is capable of introducing a cyclic and static strain pattern on a cell culture. The platform was tested with fibroblasts. The experimental results are consistent with the previously reported cytoskeleton reorganisation and cell reorientation induced by strain. The orientation of the cells is highly influenced by external mechanical cues. Cells reorganise their cytoskeleton to avoid external strain and to maintain intact extracellular matrix arrangements.

The ability to express and recognize emotion via facial expressions is well known to change with age. The present study investigated the differences in the facial recognition and facial expression of the elderly (n = 57) and the young (n = 115) and measure how each group uses different facial muscles for each emotion with Facial Action Coding System (FACS). In facial recognition task, the elderly did not recognize facial expressions better than young people and reported stronger feelings of fear and sad from photographs. In making facial expression task, the elderly rated all their facial expressions as stronger than the younger, but in fact, they expressed strong expressions in fear and anger. Furthermore, the elderly used more muscles in the lower face when making facial expressions than younger people. These results help to understand better how the facial recognition and expression of the elderly change, and show that the elderly do not effectively execute the top-down processing concerning facial expression.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

FMD is a highly contagious animal disease that occurs in cloven-hoofed animals including pigs. To prevent FMD, vaccines and adjuvants are used to induce an immune response, but it is not sufficient to show the effect of preventing viral infection. In this study, we conducted to evaluate the increasing effect of FMD vaccine SP antibody by administrating Zn-ASP to 100 pigs from three test pig farms with feed. FMD vaccine antibody titer and immunological index were analyzed using an enzyme-linked immunosorbent assay (ELISA) kit, and hematological and blood biochemical parameters were analyzed using an automatic blood analyzer. The titer of FMD vaccine SP antibody in the 0.2% Zn-ASP-administered group significantly increased compared to that in the positive control group only injected with FMD vaccine at 4 weeks after the first vaccination and at 4, 8 and 16 weeks after the second vaccination, respectively (p&lt;0.05). The FMD vaccine SP antibody positive rate was 100% until shipment. IFN-γ and IgA were significantly increased by Zn-ASP administration 4 weeks after the first vaccination and 4 weeks after the second vaccination (p&lt;0.05). On the other hand, serum AST, and CPK (p&lt;0.001) were significantly decreased by Zn-ASP. Our results show that the administration of Zn-ASP is effective in enhancing the antibody titer and immunity of the FMD vaccine by FMD vaccination, and it is thought that it can be used as an oral adjuvant (OrAd) to prevent viral diseases such as FMD.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

This article analyzes the Franco-Spanish invasion of Vietnam from 1858 to 1860. Research is based on documents such as correspondence, reports, archives and diplomatic treaties as well as monographs from the time France intended to invade Vietnam through missionary activities until the end of the Franco-Spanish invasion. The article focuses on three basic issues that are the causes of the alliance, the evolution of the French and Spanish coalition invasion in Vietnam and its impact on stakeholders. The research results on the Franco-Spanish invasion of Vietnam indicated that the invasion carried out by this alliance was more special than that of the other French coalitions before. The invasion was based on an alliance without any commitment to the interests and responsibilities of the parties. The goals of France and Spain in this invasion were different. That led to conflict between France and Spain during the invasion and the fall of the alliance. France achieved its goal through an invasion that turned Vietnam into a colony, while Spain had barely achieved its desire to have commercial and missionary interests in the area.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Purpose: To report the early clinical outcomes of combining intensity‐modulated radiation therapy (IMRT) and intensity‐modulated proton therapy (IMPT) in comparison with IMRT alone in treating the oropharynx cancer (OPC) patients. Materials and Methods: The medical records of 148 OPC patients were retrospectively reviewed, who underwent definitive radiotherapy (RT) with concurrent systemic therapy, from January 2016 till December 2019 at Samsung Medical Center. During the 5.5 weeks’ RT course, the initial 16 (or 18) fractions were delivered by IMRT in all patients, and the subsequent 12 (or 10) fractions were either by IMRT in 81 patients (IMRT only) or by IMPT in 67 (IMRT/IMPT combination), respectively, based on comparison of adaptive re-plan profiles and availability of equipment. Propensity‐score matching (PSM) was done on 76 patients (38 from each group) for comparative analyses. Results: With the median follow‐up of 24.7 months, there was no significant difference in overall survival and progression free survival between groups, both before and after PSM. Before PSM, IMRT/IMPT combination group experienced grade ≥3 acute toxicities less frequently: mucositis in 37.0% and 13.4% (p<0.001); and analgesic quantification algorithm (AQA) in 37.0% and 19.4% (p=0.019), respectively. The same trends were observed after PSM: mucositis in 39.5% and 15.8% (p=0.021); and AQA in 47.4% and 21.1% (p=0.016), respectively. In multivariate logistic regression, grade ≥3 mucositis was significantly less frequent in IMRT/IMPT combination group, both before and after PSM (p=0.027 and 0.024, respectively). AQA score ≥3 was also less frequent in IMRT/IMPT combination group, both before and after PSM (p=0.085 and 0.018, respectively). Conclusions: In treating the OPC patients, with comparable early oncologic outcomes, more favorable acute toxicity profiles were achieved following IMRT/IMPT combination than IMRT alone.

Reflux esophagitis, a treatment for gastric ulcers known as Ilaprazole (Ila), is not stable during storage and handling at room temperature, requiring storage at 5 degrees celsius. In this study, to address these issues with Ila, coformers rich in oxygen (O) and hydroxyl (OH) groups capable of forming hydrogen bonds with were selected. These coformers included Xylitol (Xyl), Meglumine (Meg), Nicotinic acid (Nic), L-Aspartic acid (Asp), and L-Glutamic acid (Glu). A 1:1 physical mixture of Ila and each coformer was prepared, and the potential for cocrystal for-mation was predicted using differential scanning calorimetry (DSC) screening. The results indi-cated the potential for cocrystal formation in the Ila/Xyl physical mixture. Subsequently, Ila and Xyl were mixed in ethyl acetate (EA) in a 1:1 ratio, and after 28 hours of slurry, the formation of Ila/Xyl cocrystal was confirmed through solid-state CP/MAS 13C NMR spectrum analysis, showing intermolecular hydrogen bonding and conformational changes. Furthermore, the 1:1 ratio of Ila/Xyl cocrystal was confirmed through solution-state NMR (1H, 13C, and 2D) molecular structure analysis. To assess the stability of Ila/Xyl cocrystal at room temperature, it was stored and com-pared with Ila at 25±2°C and relative humidity (RH) of 65±5% over three months. The results showed that the purity of Ila/Xyl cocrystal remained at 99.8% from the initial purity of 99.75% over the three months, while Ila was predicted to decrease from an initial 99.8% purity to 90% after three months. Additionally, at 25±2°C and RH 65±5%, a specific impurity B in Ila/Xyl cocrystal was observed to be 0.03% over three months, whereas Ila was predicted to increase from an initial 0.032% to 2.28% after three months. To evaluate the dissolution rate of Ila/Xyl cocrystal, a formulation was prepared and compared with Ila at pH 10, with a dosage equivalent to 10mg of Ila. The results showed that Ila/Xyl cocrystal reached 55% within 15 minutes and 100% within 45 minutes, while Ila was predicted to reach 32% at 15 minutes and 100% only after 60 minutes. However, overall, the Ila/Xyl cocrystal showed results equivalent to or exceeding the dissolution rate of Ila. Therefore, it is predicted that the Ila/Xyl cocrystal will maximize its effectiveness as a more convenient crystal structure for formulation development, allowing storage and preservation at room temperature without the need for the problematic 5°C refrigeration during ambient con-ditions and storage, addressing the issues associated with Ila.

This study aims to understand the global environment of COVID-19 management and guide future policy directions after the pandemic crisis. To this end, we analyzed a series of the World Economic Forum’s COVID-19 response reports through text mining and network analysis. These reports, written by experts in diverse fields, discuss multidimensional changes in socioeconomic situations, various problems created by those changes, and strategies to respond to national crises. Based on 3,897 refined words drawn from a morphological analysis of 26 reports (as of the end of 2020), this study analyzes the frequency of words, the relationships among words, the importance of specific documents, and the connection centrality through text mining. In addition, network analysis helps develop strategies for sustainable response to and management of national crises through identifying clusters of words with a similar structural equivalence.

Background and Objectives: The novel double-pigtail catheter (DPC) has an additional pigtail coiling at the mid-shaft with centripetal multiple side holes. The aim of the present study was to investigate the advantages and efficacy of DPC in overcoming the complications of conventional single-pigtail catheters (SPC) used to drain pleural effusion. Materials and Methods: Between July 2018 and December 2019, 382 pleural effusion drainage procedures were reviewed retrospectively (DPC, n = 156; SPC without multiple side holes, n = 110; SPC with multiple side holes [SPC+M], n = 116). All patients showed shifting pleural effusion in the decubitus view of chest radiography. All catheters were 10.2 Fr in diameter. One interventional radiologist performed all procedures and used the same anchoring technique. Complications (dysfunctional retraction, complete dislodgement, blockage, and atraumatic pneumothorax) were compared among the catheters using chi-square and Fisher’s exact tests. Clinical success was defined as improvement in pleural effusion within 3 days without additional procedures. A survival analysis was performed for calculating the indwelling time. Results: The dysfunctional retraction rate of DPC was significantly lower than that of the other catheters (p < .001). Complete dislodgement did not occur in any of the DPC cases. The clinical success rate of DPC (90.1%) was the highest. The estimated indwelling times were nine (95% confidence interval [CI]: 7.3–10.7), eight (95% CI: 6.6–9.4), and seven (95% CI: 6.3–7.7) days for SPC, SPC+M, and DPC, respectively, with DPC showing a significant difference (p < .05). Conclusions: DPC had a lower dysfunctional retraction rate compared to conventional drainage catheters. Furthermore, DPC were efficient for pleural effusion drainage with a shorter indwelling time.

This study investigated a novel radioimmunotherapy strategy for targeting tumor angiogenesis. We developed a radiopharmaceutical complex by labeling an anti-adenosine triphosphate syn-thase (ATPS) monoclonal antibody (mAb) with the radioisotope 177Lu using DOTA as a chelating agent. 177Lu-DOTA-ATPS mAb demonstrated high labeling efficiency (99.0%) and stability in se-rum. MKN-45 cancer cells exhibited the highest cellular uptake, which could be specifically blocked by unlabeled ATPS mAb. In mice, 177Lu-DOTA-ATPS mAb accumulated significantly in tumors, with a tumor uptake of 16.0 ± 1.5%ID/g on day 7. 177Lu-DOTA-ATPS mAb treatment sig-nificantly reduced the viability of MKN-45 cells in a dose-dependent manner. In a xenograft tumor model, this radioimmunotherapy strategy led to substantial tumor growth inhibition (82.8%). Furthermore, combining 177Lu-DOTA-ATPS mAb with sunitinib, an anti-angiogenic drug, en-hanced the therapeutic efficacy of sunitinib in the mouse model. Our study successfully developed 177Lu-DOTA-ATPS mAb, a radioimmunotherapy agent targeting tumor blood vessels. This ap-proach demonstrates significant promise for inhibiting tumor growth, both as a single therapy and in combination with other anti-cancer drugs.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

This study investigates the cooling effects of water facilities installed in urban parks, focusing on Sangju Namsan Park. The park features a water path and a cooling fog system, introduced as part of an environmental adaptation project to mitigate urban heat. Microclimate data were collected during the hot summer months of 2023 to assess the impact of these facilities on air temperature, humidity, and perceived thermal comfort. Results indicate that the water path and fog system reduced surface temperatures by up to 1.08°C, with additional benefits in reducing fine particulate matter and CO2 levels. The findings suggest that strategically placed water features can enhance thermal comfort and air quality in urban parks, offering a practical approach to climate change adaptation in urban planning. These insights are crucial for urban planners and policymakers aiming to improve public health and quality of life in the face of climate change.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

Alzheimer's disease (AD) is characterized by memory impairment and existence of amyloid-β (Aβ) plaques and neuroinflammation. Due to the pivotal role of oxidative damage in AD, natural antioxidative agents, such as polyphenol-rich fungi, have garnered scientific scrutiny. Here, the aqueous extract of mixed medicinal mushroom mycelia (MMMM) - Phellinus linteus, Ganoderma lucidum, and Inonotus obliquus - cultivated on a barley medium, was assessed for its anti-AD effects. A neuron-like PC12 cells, which were subjected to Zn2+, an Aβ aggregator, was employed as an in vitro AD model. The cells pretreated with or without MMMM assayed for Aβ immunofluorescence, cell viability, reactive oxygen species (ROS), apoptosis, and antioxidant enzyme activity. 5XFAD mice were administered with 30 mg/kg/day MMMM for 8 weeks and underwent memory function tests and histologic analyses. In vitro results demonstrated that the cells pretreated with MMMM exhibited attenuation in Aβ immunofluorescence, ROS accumulation, and apoptosis, and increment in cell viability and antioxidant enzyme activity. In vivo results revealed that 5XFAD mice administered with MMMM showed attenuation in memory impairment and histologic deterioration such as Aβ plaques accumulation and neuroinflammation. MMMM might mitigate AD-associated memory impairment and cerebral pathologies, including Aβ plaque accumulation, and neuroinflammation, by impeding Aβ-induced neurotoxicity.

This study aims to explore the potential inhibition effects of staurosporine isolated from a Strepto-myces sp. SNC087 strain obtained from seawater on nasal polyps. Staurosporine possesses antimi-crobial and antihypertensive activities. This research focuses on investigating the effects of stau-rosporine on suppressing the growth and development of nasal polyps and elucidating the un-derlying mechanisms involved. The experimental design includes in vitro and ex vivo evaluations to assess the inhibition activity and therapeutic potential of staurosporine against nasal polyps. Nasal polyp-derived fibroblasts (NPDFs) were stimulated with TGF- β1 in the presence of staurosporine. The levels of -smooth muscle actin (-SMA), collagen type-I (Col-1), fibronectin, and phosphory-lated (p)-Smad 2 were investigated using western blotting. VEGF expression levels were analyzed in nasal polyp organ cultures treated with staurosporine. TGF-β1 stimulated the production of Col-1, fibronectin, and -SMA and was attenuated by staurosporine pretreatment. Furthermore, these inhibitory effects were mediated by modulation of the signaling pathway of Smad 2 in TGF-β1-induced NPDFs. Staurosporine also inhibits the production of VEGF in ex vivo NP tissues. The findings from this study will contribute to a better understanding of staurosporine’s role in nasal polyp management and provide insights into its mechanisms of action.

This study focuses on the design, installation, and performance evaluation of a photovoltaic farm situated in Tulcea County, Romania, connected to a 20 kV distribution network. The farm, with a peak capacity of approximately 2800 kWp, benefits from Romania’s favorable climate conditions and supportive renewable energy policies. The analysis encompasses both the photovoltaic panel array and the electrical energy evacuation system. The substation at the park is equipped with technology that adheres to European standards and incorporates advanced features typical of modern electricity distribution networks. The assessment includes an evaluation of the park’s operational efficiency, with detailed calculations of the performance ratio and various power losses attributed to factors like temperature fluctuations, fouling, inverter efficiency, grid-related challenges, and availability issues. The farm contributes around 3620 MWh of electricity to the grid annually, demonstrating the effectiveness of photovoltaic installations in promoting sustainable energy solutions within regional energy networks.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

(1) Background: This study aimed to identify the recurrence and survival rates according to the mismatch repair (MMR), p53, and L1 cell adhesion molecule (L1CAM) states in patients with advanced and recurrent endometrial cancer receiving systemic chemotherapy.; (2) Methods: This single-center retrospective cohort study included chemotherapy-naïve patients (n=156) with advanced-stage (III/IV) or recurrent endometrial cancer who were administered chemotherapy as adjuvant therapy (n=112) or first-line palliative treatment (n=44) between January 2015 and June 2022. MMR and p53 states were assessed using PCR, and L1CAM was tested using immunohistochemistry in the no specific molecular profile (NSMP) group. The primary outcomes were progression-free survival (PFS) and overall survival (OS).; (3) Results: Of the 156 patients, 62 (39.7%), 53 (34.0%), and 41 (26.3%) had NSMP, abnormal p53 (p53abn), and an MMR deficiency (MMR-D), respectively. PFS and OS were longest in MMR-D, followed by NSMP, and were the least in p53abn tumors (PFS: p=0.0006, OS: p=0.0013). After NSMP was classified according to positive or negative L1CAM status, the L1CAM-negative group exhibited significantly lower survival rates than the L1CAM-positive group (PFS: p=0.0001, OS: p=0.0027); p53abn tumors were independent prognostic factors for poor PFS (p=0.039 on the multivariable analysis).; (4) Conclusions: In chemotherapy-naïve patients with advanced and recurrent endometrial cancer, the best prognosis after chemotherapy was obtained using MMR-D, followed by NSMP and p53abn tumors. The L1CAM status is a useful new marker for stratifying NSMP in advanced and recurrent patients.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

Background: Patients with burn scars often suffer from a ‘vicious cycle’ in which their skin becomes dry and pruritus. This greatly reduces patients' quality of life, but there is no well-known mechanism yet, and the development of drugs for effective treatment is necessary. Objective: This study evaluated the efficacy and safety of cosmetic formulation containing arginine glutamate ion pair (named as RE:pair) on epidermal barrier function and reducing pruritus. Materials and Methods: A total of 20 patients [15 male and 5 female; average age 48.35 ± 13.13 years] participated in evaluating the effectiveness of using the RE:pair formula topically twice daily for up to 4 weeks after burn pruritus. Treatment efficacy was evaluated by Numerical Rating Scale (NRS) for itching and pain, transepidermal water loss (TEWL), skin hydration, Vancouver Scar Scale (VSS) evaluation, and the patient’s overall satisfaction. Results: This formula was well-tolerated, with significant relief of NRS for itching and pain score after 2nd weeks and 4th weeks of application (p &lt; 0.05). The itching score was high in some patients, and overall, it decreased significantly after 4 weeks compared to before application. Also, the personal pain score decreased after 4th weeks. Overall TEWL showed 35 % improvement after 4th week, and 52 % improvement was confirmed in arms and 19 % in legs. The overall improvement effect of skin hydration was also 45 % (p = 0.0012), and the improvement effect was 40 % (p = 0.0371) in areas including arms and 54 % (p = 0.0313) in areas including legs. All patient satisfactory evaluations were "excellent". Conclusions: RE:pair formula was safe and effective in improving skin barrier and itch relief, and if further studies are conducted, it can be used as an excellent topical treatment for post-burn scar that strengthens the skin barrier.

Background: We aimed to identify overexpressed genes or related pathways associated with good responses to anti-HER2 therapy and to suggest a model for predicting drug response in neoadjuvant therapy with trastuzumab in HER2-positive breast cancer patients. Methods: We recruited 64 women with breast cancer and categorized them into three groups according to anti-HER2 therapy response. RNA from twenty core needle biopsy paraffin-embedded tissues and four cultured cell was extracted, reverse transcribed, and subjected to microarray. The obtained data were analyzed using Gene Ontology, Kyoto Encyclopedia of Genes and Genomes, and database for annotation, visualization, and integrated discovery. Results: In total, 6,656 genes differentially expressed between trastuzumab-susceptible and trastuzumab-resistant cell lines (3,224 upregulated and 3,432 downregulated). Expression changes in 34 genes in several pathways were found to be related to the response to trastuzumab-containing treatment, interfering with adhesion to other cells or tissues (focal adhesion) and regulating extracellular matrix interactions and phagosome action. Thus, decreased tumor invasiveness and enhanced drug effects might be the mechanisms explaining the better drug response in complete response group. Conclusions: This multigene assay-based study provides insights into breast cancer signal transduction and the possible prediction of treatment response to targeted therapies such as trastuzumab.

The maintenance of traditional agricultural practices in protected small islands is closely linked to the preservation of the land, the protection of natural resources, and the conservation of local traditions. For this purpose, the Tuscan Archipelago National Park promoted the census of ancient horticultural varieties preserved by some farmers on the island of Elba. The survey revealed a deep-rooted historical, cultural, social, and economic link between this germplasm and the island’s territory. A scientific characterization of the landrace under ethnobotanical, morphological, and genetic aspects was carried out. Among these local varieties, two landraces of the Brassica species and three landraces of the Phaseolus species were identified and analyzed in this study. To ascertain their distinguishability and uniqueness, similar varieties were also identified based on morpho-physiological characteristics or territorial proximity and compared with the Elban landraces. Morpho-phenological data were collected, and molecular analyses were carried out using Simple Sequence Repeats (SSR) markers. Ten different SSR loci were considered for the Phaseolus species and nine for the Brassica species. The Tuscan Archipelago landraces showed a high level of internal variability but were clearly distinct from each other and from the analyzed varieties, as shown by AMOVA (Analysis of Molecular Variance). Their distinctness was further highlighted by the UPGMA dendrogram obtained from the genetic distance matrix. The same results were confirmed by Principal Coordinate Analysis (PCoA). This study confirms the peculiarity of the Elban landraces, their biodiversity is a heritage to be safeguarded, which can also be used in future breeding programs. These ancient Elban landraces were allocated to local farmers (most were young farmers) to protect them from extinction and to promote more resilient varieties cultivation compared to commercial hybrids widely spread in the area. Local farmhouses also play a strategic role in safeguarding the germplasm and dissemination of sustainable agricultural practices. There is high demand for ancient Elban landraces, this has led to the development of a new local economy balanced between agricultural tradition and innovation.

A healthy park-people relation depends essentially on the fair and sustainable maintenance of rural livelihood. When protected area is designated, rural people may face restrictions of access to land and resource use for multiple ecosystem services. In Wuyishan of China, we analysed the role of traditional tea cultivation during consistent protected area management to find ways to maintain stability of this social-ecological system in the new national park era. We used an intensive social survey to investigate tea’s role, perception of ecosystem services and impacts on tea cultivation from consistent conservation policies. Results showed that tea cultivation brought major household income and associated with multiple culture services. Protected area management affected land use and conservation outcomes were more obvious to farmers than economic and social ones. From the perspective of a social-ecological system, tea cultivation in national should be conservation-compatible activities from which the potentially lost economic value is remedied by ecological and cultural valorisation. To sustain the resilience of the social-ecological system, we proposed a three-scale management framework to regulate biophysical elements at land plot scale, to link production and market at the mountain level, and to secure tenure and encourage community participation at the landscape level.

This article examines the complex interactions of the multiplier effect within the realm of tourism, with a specific emphasis on national parks. The main objective is to evaluate the multiplier effect within national parks, specifically focusing on Buiratau State National Nature Park in Kazakh-stan as a case study. The multiplier effect is a fundamental principle in the field of economic analysis. Economic multiplier effect is the term used to describe the occurrence when an initial infusion of spending in a certain industry leads to subsequent rounds of extra and sustainable economic activity. In the context of national parks, this phenomenon arises when visitor expendi-tures result in several favorable consequences, including increased employment, infrastructure advancement, and general economic expansion. The article seeks to measure the multiplier effect of tourism activities in Buiratau State National Nature Park through a thorough assessment. This entails examining several variables and datasets pertaining to visitor expenditure and its influ-ence. The study contributes to the existing literature by examining a recently constructed national park in a developing country. It compares the findings of this park with well-established national parks in other areas, emphasizing the distinct problems and opportunities it presents. Further-more, the research presents a methodological framework for evaluating the multiplier effect of national parks, which may be utilized in comparable contexts. This research ultimately enhances our comprehension of the economic implications of national parks and emphasizes their function as drivers for local and regional growth.

Candida albicans is an opportunistic fungus that becomes pathogenic and problematic under certain biological conditions. C.albicans may cause painful and uncomfortable symptoms, as well as deaths in immunocompromised patients. Therefore, early detection of c.albicans is essential. However, conventional detection methods are costly, slow and inaccessible to women in remote or developing areas. To address these concerns, we have developed a wearable and discrete naked-eye detectable, colorimetric platform for c.albicans detection. With some modification, this platform is designed to be directly adhered to existing feminine hygiene pads. Our platform is rapid, inexpensive, user-friendly, disposable and only requires three steps: i) addition of vaginal fluid onto sample pads; ii) addition of gold nanoparticle gel and running buffer, and iii) naked eye detection. Our platform is underpinned by selective thiolated aptamer-based recognition of 1,3-β-D glucan molecules- a hallmark of c.albicans cell walls. In the absence of c.albicans, wearable sample pads turn bright pink. In the presence of c. albicans, the wearable pads turn dark blue due to significant nanoparticle target-induced aggregation. We demonstrate naked eye colorimetric detection of 4.4 ×106 c.albicans cells per ml. We believe that this proof-of-concept platform has the potential to have a significant impact on women’s health, globally.

The introduction of Maritime Autonomous Surface Ship (MASS) through the development of autonomous navigation technologies is expected to bring about new technologies, new vessel types, and new job roles such as remote operation center (ROC) and remote operator (RO). The MASS Code are currently being discussed through Maritime Safety Committee (MSC) of International Maritime Organization (IMO). This code is expected to be adopted in the form of non-mandatory guidelines until 2025, with the goal of establishing mandatory requirements by 2028. Additionally, revisions to the International Convention on Standards of Training, Certification and Watchkeeping for Seafarers (STCW) related to crew training and qualifications are planned for adoption by 2027, which will include requirements for MASS operators. This paper aims to examine the fundamental competencies required for safe MASS operation by remote operators using the Analytic Hierarchy Process (AHP) method, considering the emergence of the new profession of RO. Building upon the 66 Knowledge, Understanding &amp; Proficiencies (KUPs) outlined for marine officer in the STCW Convention, the study seeks to identify the additional competencies necessary for RO and contribute to the development of a training model for the future.

In this study, a motion control problem for the vessels towed by tugboats or towing ships on the sea is considered. The towed vessels including barge ships are need to have assistance of tugboats. Combining two vessels, some work purposes in the sea or harbor area can be completed. In this study, the authors give newly developed mathematical model and control system strategy. Especially, the system model fully presenting the physical characteristics of two vessels are derived. For controlling the system effectively, it is considered that the towed vessel has no power propulsion system but the rudder is activated to improve the maneuverability. Considering the strong nonlinearities included in the vessel dynamics, the modelled system is presented by nonlinear system without linearization of nonlinear parameters. Thus, the control system for the towed vessel is designed based on the nonlinear control scheme. Exactly, the back-stepping control method is applied to its motion control. Also, the PID control method is applied for comparing with the proposed control strategy.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Microstructured surfaces are renowned for their unique properties, such as waterproofing and low adhesion, making them highly applicable in the biomedical field. These surfaces play a crucial role in influencing cell response by mimicking the native microenvironment of biological tissues. In this study, we engineered a series of biomimetic micropatterned surfaces using polydimethylsiloxane (PDMS) to explore their effects on primary breast cancer cell lines, contrasting these effects with those observed on conventional flat surfaces. The surface topography was varied to direct cells’ attachment, growth, and morphology. Our findings elucidate that surface-free energy is not merely a background factor but plays a decisive role in cell dynamics, strongly correlating with the spreading behaviour of breast cancer cells. Notably, on micropillar surfaces with high surface-free energy, an increase in the population of cancer cells was observed. Conversely, surfaces characterised by lower surface-free energies noted a reduction in cell viability. Moreover, the structural parameters, such as the gaps and diameters of the pillars, were found to critically influence cellular dispersion and adherence, underscoring the importance of the microstructures’ topography in biomedical applications. These insights pave the way for designing advanced microstructured surfaces tailored to specific cellular responses, opening new avenues for targeted cancer therapies and tissue engineering.

The tricellular tight junction protein angulin-1/lipolysis-stimulated lipoprotein receptor (LSR) is associated with numerous signal transduction pathways that regulate gene expression, epithelial cell function, and morphogenesis. The impacts of particulate matter on LSR and asthma are not known. Therefore, the aim of the present study was to assess the impacts of particulate matter as one of air pollution on LSR expression in asthma. To this end, we investigated the involvement of LSR in the pathogenesis of bronchial asthma in an ovalbumin (OVA) mouse model of asthma exposed to titanium dioxide (TiO2), and examined plasma LSR levels and their relationship with clinical variables in asthma patients and healthy controls. Plasma LSR levels were lower in asthma patients than in healthy controls. Although plasma levels of receptor for advanced glycation end-products (RAGE) were lower in asthma patients than in healthy controls, high mobility group box protein 1 (HMGB1) levels did not differ between these groups. In asthma patients, LSR levels were correlated with the forced vital capacity percentage, ratio of forced expiration (first second)-to-forced vital capacity, white blood cell count, and blood lymphocyte proportion. In mice, LSR expression was significantly decreased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Transforming growth factor beta levels were increased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Overall, plasma LSR levels were decreased in asthma patients, and were influenced by exposure to air pollution. These findings suggest the involvement of LSR in the pathogenesis of asthma.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

Aim of the study was to determine the influence of climatic and hydrological changes on the growth of Scotch pine (Pinus sylvestris L.) and Black alder (Alnus glutinosa (L.) Gaertn) in the Narew National Park over past 50 years. The researches were based on tree increment cores extracted from 42 pine trees and 57 alder trees ranging in age from 25 to 88 years and climatic (temperature and precipitation for Bialystok) and hydrological (water level of the Narew River) data. Standardized data (5-year index) were analysed by species, generation (Y - 21-40 years, M - 41-60, O - 61-90) and decade using correlation analysis. The results of the study show that pine responded more strongly to changes in air temperature and changes in precipitation totals, while alder growth was more strongly related to fluctuations in the water level of the Narew River. The most variable climatic and hydrological conditions and the most difficult conditions for tree growth prevailed in the first and last decades (1971-1980, 2011-2020). The decrease in the water level of the Narew River that occurred over the last 50 years did not adversely affect the condition of the trees. Analysis of DBH growth rates showed that the younger generations (Y, M) grow faster than the older generation (O). One of the reasons for the accelerated tree growth and increased resistance to the decline in the water level of the Narew River may be the increase in CO2 concentration in the atmosphere. Accelerated tree growth and increased resistance to drought may have certain consequences like increased damage from wind as a result of the decrease in wood density or decline in the sensitivity of trees to climate and hydrological changes. However, less sensitivity to changes in climatic conditions may only apply to older trees.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

Dermal interstitial fluid (ISF) is a novel source of biomarkers that can be considered as an alternative to blood sampling for disease diagnosis and treatment. Nevertheless, in vivo extraction and analysis of ISF are challenging. On the other hand, microneedle (MN) technology can address most of the challenges associated with dermal ISF extraction and is well-suited for long-term, continuous ISF monitoring as well as in situ detection. In this review, we first briefly summarise the different dermal ISF collection methods and compare them with MN methods. Next, we elaborate on the design considerations and biocompatibility of MNs. Subsequently, the fabrication technologies of various MNs used for dermal ISF extraction, including solid MNs, hollow MNs, porous MNs and hydrogel MNs, are thoroughly explained. In addition, different sensing mechanisms of ISF detection will be discussed in detail. Subsequently, we identify the challenges and propose the possible solutions associated with ISF extraction. A detailed investigation is provided for the transport and sampling mechanism of ISF in vivo. Also, the current in vitro skin model integrated with the MN arrays will be discussed. Finally, future directions to develop a point-of-care (POC) device to sample ISF are proposed.

Access to urban green and blue spaces (UGBS) has been associated with positive effects on health and wellbeing; however, the past decades have seen a decline in quality and user satisfaction with UGBS. This reflects the mounting challenges that many UK cities face in providing appropriate public facilities alongside issues such as health inequalities, an ageing population, climate change, and loss of biodiversity. At present, little is known about the preferences of different population subgroups and, specifically, the UGBS they visit and the spaces they avoid. Using a public participatory geographic information system (PPGIS), the overall aim of the research presented here was to investigate the preferences of different population subgroups in urban areas, and the UGBS they visit, using Edinburgh, Scotland as a case study. We created a baseline visitor demographic profile for UGBS use, and highlighted how visitors perceive, physically access, use, and engage with UGBS. The results revealed considerable variation in UGBS preference: one person’s favourite UGBS may be one that someone else dislikes and avoids. It is clear that adapting UGBS to suit local communities should not be a ‘one-size-fits-all’ approach. The conflicting views and preferences of different groups of respondents point to the importance of developing policies and park management plans that can accommodate a variety of uses and experiential qualities within individual parks. PPGIS offers an ideal tool for achieving this

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Rottlerin(R) is a natural extract from Mallotus philippensis with antiviral properties. Feline Infectious Peritonitis (FIP) is a fatal disease characterized by systemic granulomatous inflammation and high mortality, with no established prevention or cure. We investigated antiviral effect of liposome loaded R, Rottlerin-liposome(RL) against Feline infectious peritonitis virus (FIPV), the causative agent. We demonstrated that R and RL inhibited FIPV replication in dose dependently with a PKCδ related manner, not only in the early endocytosis step but also in the late step of replication. RL resolved the low solubility issue of rottlerin and improved its inhibition efficacy at the cellular level. Based on these findings, we suggest that RL has a value for further research as a potential antiviral agent against FIPV.

Cultural heritage is a fundamental part of the society’s identity, and its conservation is of great relevance as it transcends time and memory. To minimize its deterioration, cultural heritage has traditionally undergone diverse preservation and maintenance treatments and the attention of researchers to develop new and innovative methods for state diagnosis and protection treatments has been increasing in the recent decades. Therefore, in this study, a literature review using a bibliometric analysis and LDA methodology was conducted to systematically map scientific research outputs on cultural heritage conservation and protection. Data was retrieved from the Scopus database and the annual publications, countries, most-cited publications, authors, institutions, and keywords have been comprehensively analyzed, leading to the detection of research trends. Findings show an increasing number of studies in this field in the last decades, particularly since 2010. Italy, home to the largest number of UNESCO heritage sites, is the most prolific country. Most of the studies are related to metal, paper and stone as substrate to be protected. Significant progress has been made in understanding the deterioration processes through precise diagnosis and the development of innovative treatments for protection. In this sense, latest trends have been detected such as the use of non-invasive techniques for diagnosis and the use of nanotechnology and nature-based treatments for the conservation treatments.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

Various peptides or non-structural amino acids are recognized by their specific target proteins and perform biological role in various pathways in vivo. Understanding the interactions between target protein and peptides (or non-structural amino acids) provides key information on the molecular interactions, which can be potentially translated to the development of novel drugs. However, it is experimentally challenging to determine the crystal structure of protein-peptide complexes. To obtain structural information on substrate recognition of peptide-recognizing enzyme, X-ray crystallographic studies were performed using triglycine (Gly-Gly-Gly) as main-chain of peptide. The crystal structure of Parengyodontium album Proteinase K in complex with triglcyine was determined at 1.4 Å resolution. Two different bound conformations of triglycine were observed at the substrate recognition site. The triglycine backbone forms stable interactions with β5-α4 and α5-β6 loops of main-chain. One of the triglycine-binding conformations was identical with the binding mode of a peptide-based inhibitor from a previously reported crystal structure of Proteinase K. Triglycine has potential application X-ray crystallography to identify substrate recognition sites in peptide binding enzymes.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

Corresponding to the principles of biological synapses, an essential prerequisite for hardware neural networks using electronics devices is continuous regulation of conductance. We implemented artificial synaptic characteristics in a (GeTe/Sb2Te3)16 iPCM with a superlattice structure under optimized identical pulse trains. Based on atomically controlling the Ge switch in the phase transition that appears in the GeTe/Sb2Te3 superlattice structure, multiple conductance states were implemented by applying the appropriate electrical pulses. Furthermore, we found that the bidirectional switching behavior of a (GeTe/Sb2Te3)16 iPCM can achieve a desired resistance level using the pulse width. Therefore, we also fabricated a Ge2Sb2Te5 PCM and designed a pulse scheme based on the phase transition mechanism to compare to the (GeTe/Sb2Te3)16 iPCM. We designed an identical pulse scheme that implements linear and symmetrical LTP and LTD based on the iPCM mechanism. As a result, the (GeTe/Sb2Te3)16 iPCM showed relatively excellent synaptic characteristics by implementing gradual conductance modulation, a nonlinearity value of 0.32, and LTP/LTD 40 conductance states using identical pulses trains. Our results demonstrate the general applicability of the artificial synaptic device for potential use in neuro-inspired computing and next generation non-volatile memory.

In-wheel motor vehicles are gaining attention as a new type of electric vehicle due to their efficient power units located inside each wheel hub. However, they are more susceptible to wheel resonance due to the increase in unsprung mass caused by the motor's weight. This can result in decreased both the ride comfort and driving stability. To resolve this issue, this study aims to apply an optimal switching controller with a semi-active n actuator; magnetorheological (MR) damper. For the implementation of the optimal switching controller, a road type classification is also carried out. An acceleration sensor is used for road type classification, and control logics include a ride comfort controller; the linear quadratic regulator (LQR _Paved Road) and a wheel motion controller (LQR_Off Road) for improved driving stability. For paved roads, the LQR_Paved Road control input is applied to the MR damper. However, if a road type prone to wheel resonance is detected, the control logic switches to the LQR_Off Road. During the transition, a weighted average of both LQR_ Paved Road and LQR_Off Road control input is applied to the actuator. Computer simulations are undertaken to evaluate vibration control performance, including the ride comfort and driving stability at various road profiles.

The aim of this paper is to study changes in land use and the evolution of vegetation in Cacheu River Mangroves Natural Park in the Republic of Guinea-Bissau. To do this, we will study variations in the NDVI, Normalized Difference Vegetation Index. In order to perform the calculations and subsequent analysis, images from three years— 2010, and 2017—were used, all corresponding to the same time of year so that the phenological stage is the same. To perform a more reliable analysis, the park was divided into five classes based on the main use of the land: mangals, palm forest, paddy fields, savannahs and others. Using a statistical sample, same areas were selected for each class and the corresponding NDVIs were calculated for the years in which ASTER images were available. The study made it possible to conclude that at present, management of the park is not the most suitable, given that the changes in land use observed represent a decrease in mangrove swamps, despite the fact that these forests constitute the most important ecological area of all those that make up the park. Mangals are being replaced by other land uses.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

The purpose of this study is to explore the effects of dual-task training, including cognitive tasks, on cognitive and bodily functioning and β-amyloid levels in Alzheimer's dementia patients. The subjects were 34 inpatients diagnosed with Alzheimer's dementia at a nursing hospital located in Gyeongsansi, South Korea. The patients were randomly divided into a dual-task group (n = 16) and a single-task group (n = 18). The dual-task group performed cognitive tasks at the same time as exercising tasks, while the single-task group performed only exercise tasks. Each group was trained for 30 minutes three times a week for eight weeks. The Mini-Mental State Examination was used to measure the patients’ cognitive function. Static and dynamic balance were measured to evaluate bodily functioning. Static balance was measured using Biorescue, while dynamic balance was measured using the Berg Balance Scale. Blood analysis was performed to measure levels of β-amyloid, which is known to cause Alzheimer's dementia. Both groups exhibited statistically significant improvements in gait function after the training (p < .05). The dual-task group exhibited statistically significant differences in cognitive function, static and dynamic balance function, and β-amyloid levels after training (p < .05). A significant difference was observed between the two groups (p < .05). Dual-task activities were found to be effective in improving cognitive and bodily functioning and reducing β-amyloid levels in Alzheimer's dementia patients. Therefore, dual-task training is thought to be an effective method of treating and preventing Alzheimer's dementia.

Mushroom cultivation vastly improves the yield of mushrooms under optimized, controlled conditions, but may be susceptible to opportunistic colonization by pest species that can establish themselves, as well as the pathogens and pests they may transmit. Here we describe our investigation into the bacterial communities of adult Lycoriella ingenua (Diptera: Sciaridae) and Megaselia halterata (Diptera: Phoridae) collected from button mushroom (Agaricus bisporus) production houses in Pennsylvania. We collected adult flies and sequenced the hypervariable v4 region of the bacterial 16S rRNA using the Illumina MiSeq. The most abundant bacterial genus detected in both species was Wolbachia, but phylogenetic analysis revealed that the infections are from different clades. Future studies include the characterization of Wolbachia infections on fly behavior and biology, comparison of microbial diversity of fly species colonizing wild mushrooms, and other microbiota that may contribute to the success of certain pest fly species.

The low relative humidity (RH) levels in a greenhouse during the daytime in a strawberry (Fragaria × ananassa Duch) cultivation period negatively affect the growth of strawberry related to photo-physiology. Therefore, this study was conducted to confirm an efficient RH management method by analyzing the phenotypic characteristics related to photo-physiology by controlling the RH in a greenhouse during the daytime with a fog system. Strawberry plants were grown respectively in a greenhouse affected by natural RH changes (control) and in a greenhouse with 40% ~ 50% RH adjusted during the daytime using a fog system. In the greenhouse, with controlled RH, the temperature decreased, and the RH was higher in the initial growth stage of strawberry planting than the control. It was observed a significant increase in the survival rate of the strawberry plant, as well as the incidence of powdery mildew, was lowered. In addition, the photosynthetic rate and OJIP chlorophyll a fluorescence transients related to photosystem II efficiency of strawberry leaves were significantly higher in the fog treatment than in the control. In winter, during the day, the number of days on which the temperature dropped below 20℃ has increased, the greenhouse temperature with controlled RH was lower due to the fog system. When the yield per strawberry plant in January and February was investigated, the control was higher than the RH treatment. Therefore, RH management using a fog system must be controlled at a level where a temperature range is adequate for plant growth, in which the efficient control of these parameters increases strawberry productivity.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

In this study, the focus is on the drop test simulation of an MR (Magnetorheological) damper-based main landing gear (MRMLG), aiming to explore multi-degree-of-freedom (DOF) dynamic models during aircraft landing. Three different 6-DOF dynamic models are proposed in this work and their drop performances are compared with results achieved one of commercial softwares. The proposed models include a nonlinear aircraft model (NLAM), a linearized approximated aircraft model (LAAM) linearizing from the nonlinear equations of motion in NLAM, and a fully approximated aircraft model (FAAM) which linearizes the MRMLG's strut force model. In order to evaluate drop performance of the aircraft landing gear system with MR dampers, a 7-DOF aircraft model incorporating the nonlinear MRMLG is formulated using RecurDyn. The principal comparative param-eters are the coefficient of determination (R2) for system response of each model with Re-curDyn model and root mean square error (RMSE) which is the ensembles of CG dis-placement data for each model. In addition, the ensemble of time series data is created for diverse drop scenarios, providing valuable insights into the performance of the proposed drop test models of the aircraft landing gear system featuring MR dampers.

Magnetorheological (MR) fluid is recognized as one of intelligent materials that is widely used for various kinds of controllable devices since its rheological characteristics can be controlled by an external magnetic field (or input current). However, the density mismatch of the compositions between iron particles and carrier oil leads to inevitable sedimentation. Therefore, many works on the sedimentation problem of MR fluids have been carried out to improve the sedimentation stability using appropriate additives, surfactants, nanoparticles, particle coating as well as using several carrier oils with different densities. However, a study on the effect of the current magnitudes and profiles on the sedimentation is considerably rare. This study experimentally investigates the sedimentation behaviors due to the different current magnitudes and different profiles such as square and sine wave. It is shown that average sedimentation rate is 98.61% by applying 1 A of the square wave, while it is 97.83% under the sine type of the current. It is also identified that the higher intensity of the applied current results in stronger electromagnetic which can slow down the sedimentation rate. The results presented in this work are very helpful in designing a controller which provides the input current in terms of the magnitude and profile configuration.

Early detection of neurological conditions is critical for timely diagnosis and treatment. Identifying cellular-level changes is essential for implementing therapeutic interventions prior to symptomatic disease onset. However, monitoring brain tissue directly through biopsies is invasive and high-risk. Bodily fluids such as blood or cerebrospinal fluid contain information in many forms, including proteins and nucleic acids. Particularly, cell-free DNA (cfDNA) has potential as a versatile neurological biomarker. Yet, our knowledge of cfDNA released by brain tissue and how cfDNA changes in response to deleterious events within the brain is incomplete. Mapping changes in cfDNA to specific cellular events is difficult in vivo, where many tissues contribute to circulating cfDNA. Organoids are tractable systems for examining specific changes consistently in a human background. However, few studies have investigated cfDNA released from organoids. Here, we examined cfDNA isolated from cerebral organoids. We found that cerebral organoids release quantities of cfDNA sufficient for downstream analysis with droplet-digital PCR and whole-genome sequencing. Further, gene ontology analysis of genes aligning with sequenced cfDNA fragments revealed association with terms related to neurodevelopment and autism spectrum disorder. We conclude that cerebral organoids hold promise as tools for the discovery of cfDNA biomarkers related to neurodevelopmental and neurological disorders.

This article explored how some state policies on rehabilitation, protection and utilization of mangroves are implemented at two locals; namely, Ca Mau provice and its sub-unit Ngoc Hien District as well as Ho Chi Minh City and its sub-unit Can Gio District and what are considered as emgerging issues in the implementation process. The study employed mixed research methods including document and thematic analysis, in-depth interviews, and group discussion. The findings showed that state policies would be adapted through the ways in which these two locals manage to silmultaneously orient their work toward accommodating the madates placed upon them and cope with the reality of socio-economic difficulties at their levels. The findings also showed some issues that need to consider addressing; namely, locals’ struggles to fill the gaps between written and implemented policies in mangrove rehabilitation, conflict among sectors and stakeholders in mangrove utilization and protection, problems in guaranteeing adequate budget for in-need-locals, inconsistence in policies on "forest: water surface” ratio in mangrove-shrimp farm, and unintended consequences in forest thinning and exploitation regimes. Based on the finding analysis, the articles discussed lessons learned from the policy implementation process on mangrove rehabilitation, management and forest allocation to household in the south of Vietnam.

Flow sensing in hostile environment is of increasing interest for applications in automotive, aerospace, and chemical and resource industries. Compared to their counterparts, thermal flow sensors are attractive candidates due to the ease of fabrication, lack of moving parts and higher sensitivity. Recently, a number of thermal flow sensor prototypes have been reported in the literature demonstrating the measurement of fluid flows under hostile conditions. This paper summarizes the concept of thermal flow sensing, operational modes and transduction mechanisms. Then, the choice of materials and their corresponding properties are presented in details. The paper also reports recent progress in the development of thermal flow sensors for harsh environment. In addition, the issues and considerations in packaging are reviewed. Finally, we conclude the review with the future prospects.

As a form of protection, a nature park is often created to protect and valorise natural and cultural heritage in peripheral rural areas. However, in terms of multi-functionality, new nature parks are incorporated into traditional productive activities, such as recreational and tourist activities, which sometimes compromise sustainability. The research objective is to study the relationship between tourism and sustainability in the Nature Parks of “Sierra de Aracena y Picos de Aroche”, “Sierra Norte de Sevilla” and “Sierra de Hornachuelos” that makes up the Dehesas de Sierra Morena Biosphere Reserve in Andalusia, Spain. Therefore, selective interviews have been carried out with the stakeholders to establish their perception of sustainable tourism and the presence of dominant discourses. The main conclusions indicate (1) the presence of different dominant discourses on sustainability, namely the conservationist and mercantilist ones, with the prevalence of the economic dimension; (2) poor awareness and adaptation to the context of global change; and (3) the presence of competitive relationships that generate difficulties for the governance of sustainable tourism.

The number of people owning vehicles has been steadily growing, resulting in increased numbers of vehicles on the roads, making roads more congested, and increasing the risk of accidents. In addition, heavy rain, snow, and fog have increased due to abnormal weather caused by global warming. These bad weather conditions can also affect the safety of vehicles and drivers. The need to disseminate safety messages on the social internet of vehicles due to these problems has been steadily increasing. In this paper, we propose an efficient safety message dissemination scheme that focuses on urban environments with high vehicle density and mobility to address these problems. The proposed scheme reduces packet loss by considering frequent cluster departures and subscriptions through an efficient cluster management technique. In a vehicle-to-vehicle environment, the dissemination of safety messages is divided into an intra-cluster and an inter-cluster emergency as well as general safety message dissemination technique. In a vehicle to infrastructure environment, the proposed scheme reduces the number of processing requests and duplicate messages made to roadside units (RSUs) through a request operation process for each vehicle and an RSU scheduling technique. We conducted several performance evaluations of message packet loss and the number of RSU processing requests to demonstrate the superiority of the proposed scheme.

In the present era, infertility is one of the major issues which restricts many couples to have their own kids. Infertility is the inability to achieve a clinical pregnancy after regular unprotected sexual intercourse for the period of one year or more. Various factors including defective male or female germ cell development, unhealthy and improper lifestyles, diseases like cancer and associated chemo-or-radiation therapies, congenital disorders etc. may be responsible for infertility. Therefore, it is highly important to understand the basic concepts of germ cell development including primordial germ cell (PGC) formation, specification, migration, entry to genital ridges and their molecular mechanisms, activated pathways, paracrine and autocrine signaling, along with possible alteration which can hamper germ cell development and can cause adversities like cancer progression and infertility. Knowing all these aspects in a proper way can be very much helpful in improving our understanding about gametogenesis and finding possible ways to cure related disorders. Here in this review, various aspects of gametogenesis especially female gametes and relevant factors causing functional impairment have been thoroughly discussed.

Various short-range radars, such as impulse-radio ultra-wideband (IR-UWB) and frequency-modulated continuous-wave (FMCW) radars, are currently employed to monitor vital signs, including respiratory and cardiac rates (RR and CR). However, these methods do not consider the motion of an individual, which can distort the phase of the reflected signal, leading to inaccurate estimation of RR and CR because of a smeared spectrum. Therefore, motion compensation (MOCOM) is crucial for accurately estimating these vital rates. This paper proposes an efficient method incorporating MOCOM to estimate RR and CR with super-resolution accuracy. The proposed method effectively models the radar signal phase and compensates for motion. Additionally, applying the super-resolution technique to RR and CR separately further increases the estimation accuracy. Experimental results from the IR-UWB and FMCW radars demonstrate that the proposed method successfully estimates RR and CR even in the presence of body movement.

A simple approach was developed to predict corn yields using the MoDerate Resolution Imaging Spectroradiometer (MODIS) data product from two geographically separate major corn crop production regions: Illinois, USA and Heilongjiang, China. The MOD09A1 data product, which are 8-day interval surface reflectance data, were obtained from day of the year (DOY) 89 to 337 to calculate the leaf area index (LAI). The sum of the LAI from early in the season to a given date in the season [end of DOY (EOD)] was well fitted to a logistic function and represented seasonal changes in leaf area duration (LAD). A simple phenology model was derived to estimate the dates of emergence and maturity using the logistic function parameters b1 and b2, which represented the rate of increase in LAI and the date of maximum LAI, respectively. The phenology model predicted emergence and maturity dates fairly well, with root mean square error (RMSE) values of 6.3 and 4.9 days for the validation dataset, respectively. Two simple linear regression models (YP and YF) were established using LAD as the variable to predict corn yield; the yield model (YP) used LAD from predicted emergence to maturity, and the yield model (YF) used LAD for a predetermined period from DOY 89 to a particular EOD. When state/province corn yields for the validation dataset were predicted at DOY 321, near completion of the corn harvest, the YP model performed much better than the YF model, with RMSE values of 0.68 t/ha and 0.66 t/ha for Illinois and Heilongjiang, respectively. The YP model showed a similar or better performance, even for the much earlier yield prediction at DOY 257, compared to that of the YF model. In conclusion, the phenology and yield models were developed based only on logistic changes in remote sensing-derived LAD, and predicted phenological dates and corn yields with considerable accuracy and precision for the two regions selected for this study. However, these models must be examined for spatial portability in more diverse agro-climatic regions.

Recently, a high internal surface of the titanium alloy pipe is required due to the increment of various applications of the pipe such as aerospace. However, the traditional machining process is unable to effectively polish the internal surface of the slender pipe. Thus, a vertical magnetorheological polishing (VMRP) apparatus is carried out in this work to implement high polishing performance on the internal surface of the titanium alloy pipe. The polishing process is realized by the combination of the rotating motion of the pipe and the reciprocating linear motion of the polishing head. Moreover, a series of comparative experiments are conducted to investigate the polishing mechanism of magnetorheological (MR) fluid and enhance the polishing performance. It is shown from the experimental results that proposed VMRP approach exhibits the better polishing performance than the conventional horizontal MR polishing method under same testing conditions. This is because the proposed VMRP method well eliminates the traces of polishing particles owing to the combination of polishing particles with different sizes. In addition, it is identified from the experimental test that the polishing time of the VMRP required to achieve the same polishing effect as the conventional method is shortened under the combination of different rotation speeds. It is identified from the above benefits of the VMRP that the final surface roughness after polishing is below 0.05 μm.

In this study, nano-diamond (ND) and MoS2 powder are used as additives in a carbonyl iron based magnetorheological fluid (MRF) to improve its tribological performance. MRFs are prepared by dispersing 35 wt.% of CI particles in silicone oil, and adding different proportions (0, 1, 3 or 5 wt.%) of ND and MoS2 additives. Seven kinds of MRFs are made and tested using reciprocating friction and wear tester under different normal loads, and then the friction characteristics are evaluated through analyzing experiment results. The morphology properties of MRFs and contacting surfaces before and after tests are also observed using a scanning electron microscope and analyzed by energy-dispersive X-ray spectroscopy. The results show that the appropriate weight percentage of MoS2 additives may decrease friction coefficient and wear zone. It is also demonstrated from the detailed analyses of worn surfaces that the wear mechanism is influenced not only by additives but also by applied normal load and magnetic field strength.

Bisphenol A production plant possesses considerable potential risks in the top of the methanol separation column, as pressurized acetone, methanol and water are processed at an elevated temperature, especially in the event of an abnormal pressure increase due to sudden power outage. This study assesses the potential risks in the methanol separation column through hazard and operability assessment and evaluates the damages in the case of fire and explosion accident scenarios. The study chooses three leakage scenarios: a 5-mm puncture on the methanol separation column, a 50-mm diameter fracture of a discharge pipe and a catastrophic rupture, and simulates using Phast (Ver. 6.531) the concentration distribution of scattered methanol, thermal radiation distribution of fires and overpressure distribution of vapor cloud explosions. Implementation of safety instrumented system equipped with two-out-of-three voting as a safety measure can detect overpressure at the top of the column and shut down the main control valve and the emergency shutoff valve simultaneously, all at the same time. By applying safety integrity level of three, the maximal release volume of the safety relief valve can be reduced and therefore, the design capacity of the flare stack can also be reduced. Such integration will lead to improved safety at a reduced cost.

Prosthetics have come a long way since their inception, and recent advancements in materials science have enabled the development of prosthetic devices with improved functionality and comfort. One promising area of research is the use of auxetic metamaterials in prosthetics. Auxetic materials have a negative Poisson's ratio, which means that they expand laterally when stretched, unlike conventional materials, which contract laterally. This unique property allows for the creation of prosthetic devices that can better conform to the contours of the human body and provide a more natural feel. In this review article, we provide an overview of the current state of the art in the development of prosthetics using auxetic metamaterials. We discuss the mechanical properties of these materials, including their negative Poisson's ratio and other properties that make them suitable for use in prosthetic devices. We also explore the limitations that currently exist in implementing these materials in prosthetic devices, including challenges in manufacturing and cost. Despite these challenges, the future prospects for the development of prosthetic devices using auxetic metamaterials are promising. Continued research and development in this field could lead to the creation of more comfortable, functional, and natural-feeling prosthetic devices. Overall, the use of auxetic metamaterials in prosthetics represents a promising area of research with the potential to improve the lives of millions of people around the world who rely on prosthetic devices.

Hepatitis C virus (HCV) is a major medical health burden and leading cause of chronic liver disease and cancer worldwide. More than 58 million people are chronically infected with HCV, with 1.5 million new infections occurring each year. An effective HCV vaccine is a major public health and medical need as recognized by the World Health Organization. However, due to the high variability of the virus and its ability to escape the immune response, HCV rapidly accumulates mutations making a vaccine a formidable challenge. An effective vaccine must elicit broadly neutralizing antibodies (bnAbs) in a consistent fashion. After decades of studies from basic research through clinical development, the antigen of choice is considered to be the E1E2 envelope glycoprotein due to conserved, broadly neutralizing antigenic domains located in the constituent subunits of E1, E2, and the E1E2 heterodimeric complex itself. The challenge has been elicitation of robust humoral and cellular responses leading to broad virus neutralization due to the relatively low immunogenicity of this antigen. In view of this challenge, structure-based vaccine design approaches to stabilize key antigenic domains have been hampered due to the lack of E1E2 atomic-level resolution structures to guide them. Another challenge has been development of a delivery platform in which a multivalent form of the antigen can be presented in order to elicit a more robust anti-HCV immune response. Recent nanoparticle vaccines are gaining prominence in the field due to their ability to facilitate a controlled multivalent presentation and trafficking to lymph nodes, where they can interact with both the cellular and humoral components of the immune system. This review focuses on recent advances in understanding the E1E2 heterodimeric structure to facilitate a rational design approach and the potential for development of a multivalent nanoparticle-based HCV E1E2 vaccine. Both aspects are considered important in the development of an effective HCV vaccine that can effectively address viral diversity and escape.

Singing melody extraction is the task that identifies the melody pitch contour of singing voice from polyphonic music. Most of the traditional melody extraction algorithms are based on calculating salient pitch candidates or separating the melody source from the mixture. Recently, classification-based approach based on deep learning has drawn much attentions. In this paper, we present a classification-based singing melody extraction model using deep convolutional neural networks. The proposed model consists of a singing pitch extractor (SPE) and a singing voice activity detector (SVAD). The SPE is trained to predict a high-resolution pitch label of singing voice from a short segment of spectrogram. This allows the model to predict highly continuous curves. The melody contour is smoothed further by post-processing the output of the melody extractor. The SVAD is trained to determine if a long segment of mel-spectrogram contains a singing voice. This often produces voice false alarm errors around the boundary of singing segments. We reduced them by exploiting the output of the SPE. Finally, we evaluate the proposed melody extraction model on several public datasets. The results show that the proposed model is comparable to state-of-the-art algorithms.

Pyruvate kinase M2 (PKM2) is essential for aerobic glycolysis and is highly expressed in various cancer tissues. Although high PKM2 expression is observed in prostate cancer tissues, its functional role in cancer metabolism is unclear. Here, we investigated the role of PKM2 in regulating autophagy and its associated pathways in prostate cancer cells. PKM2 expression was silenced using various PKM2 small interfering RNAs (siRNAs) and then we measured PKM2-related cellular pathways associated with autophagy. PKM2 siRNA-transfected prostate cancer cells showed significantly reduced viability. Acridine orange staining and immunoblotting analysis showed that PKM2 downregulation markedly increased autophagic cell death. Results of western blotting analysis showed that PKM2 knockdown affected protein kinase B/mechanistic target of rapamycin 1 pathway, which consequently downregulated the expression of glycolytic enzymes lactate dehydrogenase A and glucose transporter 1. To the best of our knowledge, this is the first study to show that PKM2 inhibition alters cancer cell metabolism and induces autophagy. Thus, the present study provides a strategy for the development of PKM2-targeted novel anticancer drugs for the treatment of prostate cancer.

This paper reports the design, development, and testing of a novel, yet simple and low-cost portable device for the rapid detection of SARS-CoV-2. The device performs loop mediated isothermal amplification (LAMP) and provides visually distinguishable images of the fluorescence emitted from the samples. The device utilises an aluminium block embedded with a cartridge heater for isothermal heating of the sample and a single-board computer and camera for fluorescence detection. The device demonstrates promising results within 20 minutes using clinically relevant starting concentrations of the synthetic template. Time-to-signal data for this device are considerably lower compared to standard qPCR machine (~10-20 minutes vs &gt;38 minutes) for 1×105 starting template copy number. The device in its fully optimized and characterized state can potentially be used as simple to operate, rapid, sensitive, and inexpensive platform for population screening as well as point-of-need SARS-CoV-2 detection and patient management.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

Cellular response to mechanical stimuli is a crucial factor for maintaining cell homeostasis. The interaction between extracellular matrix and mechanical stress plays a significant role in organ-izing the cytoskeleton and aligning cells. Tools that apply mechanical forces to cells and tissues, as well as those capable of measuring the mechanical properties of biological cells, have greatly contributed to our understanding of fundamental mechanobiology. These tools have been exten-sively employed to unveil the substantial influence of mechanical cues on the development and progression of various diseases. In this report, we present an economical and high-performance uniaxial cell stretching device. This paper reports the detailed operation concept of the device, ex-perimental design, and characterization. The device was tested with MDA-MB-231 breast cancer cells. Experimental results agree well with previously documented morphological changes re-sulting from stretching forces on cancer cells. Remarkably, our new device demonstrates compa-rable cellular changes within a 30-minute compared to the previous 2-hour stretching duration. Moreover, the device design incorporates an open-source software interface, facilitating conven-ient parameter adjustments such as strain, stretching speed, frequency, and duration. Its versatil-ity enables seamless integration with various optical microscopes, thereby yielding novel insights into the realm of mechanobiology.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

We report on an immunofluorescent paper-based assay for the detection of severe acute respiratory symptom coronavirus 2 (SARS-CoV-2) humanized antibody. The paper-based device was fabricated by using lamination technique for easy and optimized handling. Our approach utilises a two-step strategy that involves (i) initial coating of the paper-electrode with recombinant SARS-CoV-2 nucleocapsid antigen to capture the target SARS-CoV-2 specific antibodies, and (ii) subsequent detection of SARS-CoV-2 antibodies using fluorophore-conjugated IgG antibody. The fluorescence readout was observed with fluorescence microscopy. The images were processed and quantified using a MATLAB program. The assay can selectively detect SARS-CoV-2 humanized antibodies spiked in PBS and healthy human serum samples with the relative standard deviation of approximately 6.4% (for n = 3). It has broad dynamic ranges (1 ng to 50 ng/µL in PBS and 5 to 100 ng/µL in human serum samples) for SARS-CoV-2 humanized antibodies with the detection limits of 2 ng/µL (0.025 IU/mL) and 10 ng/µL (0.125 IU/mL) in PBS and human serum samples, respectively. We believe that our assay has the potential to be used as a simple, rapid, and inexpensive paper-based diagnostic device with a portable fluorescent reader to provide point-of-care diagnosis. This assay can be used for rapid examination of a large batch of samples toward clinical screening of SARS-CoV-2 specific antibodies as a confirmed infected active case or to evaluate the immune response to a SARS-CoV-2 vaccine.

Background: G6PD is a rate-limiting enzyme of the pentose phosphate pathway. The loss of G6PD activity in red blood cells exposes to the risk of acute haemolytic anaemia under oxidative stress, induced by infections, some medications, or fava beans. More than 200 single missense mutations are known in the G6PD gene. This study reports a 41-year-old woman coming from Basilicata region (Italy) that carried out the G6PD status in our hospital for prenatal investiga-tions. Methods: DNA was extracted from peripheral blood sample and genotyped for common-est G6PD pathogenic variants (PVs). Positive results obtained by Restriction Fragment Length Polymorphism (RFLP), as per practice in our laboratory, are then re-confirmed in Sanger se-quencing. Results: RFLP analysis highlighted a variant compatible with G6PD Cassano variant. Confirmatory testing by Sanger unexpectedly identified a novel variant: c.1357G>A, p.(Val453Met) (NM_001360016.2). In silico models predicted a deleterious effect of this variant at the protein level. The novel G6PD variant was named "G6PD Potenza", on the basis of the pa-tient's regional origin. Conclusion: This case describes a novel G6PD variant. It also highlights how the Sanger sequencing technique still represents an indispensable confirmatory standard method for variants that could be miss-interpreted by using of “first-level” approached, as the RFLP. We stress that the evaluation of clinical manifestations in G6PD deficient patients is of primary importance for the classification of each new G6PD mutation, in agreement with the new WHO guidelines.

Land use/land cover (LULC) and climate changes are two main factors directly affecting hydrologic conditions. However, very few studies in Vietnam have investigated changes in hydrological process under the impact of climate and land use changes on a basin scale. The objective of this study is to assess the individual and combined impacts of land use and climate changes on hydrological processes for the Nam Rom river basin, Northwestern Viet Nam using Remote Sensing (RS) and Soil and Water Assessment Tools (SWAT) model. SWAT model was used for hydrological process simulation. Results indicated that SWAT proved to be a powerful tool in simulating the impacts of land use and climate change on catchment hydrology. The change in historical land use between 1992 and 2015 strongly contributed to increasing hydrological processes (ET, percolation, ground water, and water yield), whereas, climate change led to significant decrease of all hydrological components. The combination of land use and climate changes significantly reduced surface runoff (-16.9%), ground water (-5.7%), water yield (-9.2%), and sediment load (-4.9%). Overall climatic changes had more significant effect on hydrological components than land use changes in the Nam Rom river basin during the 1992–2015. Under impacts of projected land use and climate change scenarios in 2030 on hydrological process of the upper Nam Rom river basin indicate that ET and surface flow are more sensitive to the changes in land use and climate in the future. In conclusion, the findings of this study will basic knowledge of the effects of climate and land-use changes on the hydrology for future development of integrated land use and water management practices in Nam Rom river basin.

Non-Orthogonal Multiple Access (NOMA) is the key technology promised to be applied in next-generation networks in the near future. In this study, we propose a multi-points cooperative relaying (MPCR) NOMA model instead of just using a relay as the previous studies. Based on the channel state information (CSI), the base station (BS) selects a closest user equipment (UE) and sends a superposed signal to this UE as a first relay node. We have assumed that there are N UEs in the network and Nth UE, which is farthest from BS, has the poorest quality signal transmitted from the BS compared other UEs. Nth UE received the forwarded signal from N-1 relaying nodes that are UEs with better signal quality. At the ith relaying node, it detect its own symbol by using successive interference cancellation (SIC) and will forward the composite signal to the next closest user, namely i+1th UE, and include an excess power which will use for energy harvesting (EH) intention at the next UE. By these, the farthest UE in network can be significantly improved. In addition, closed-form expressions of outage probability for users over both the Rayleigh and Nakagami-m fading channels are also presented. Analysis and simulation results performed by Matlab software which are presented accurately and clearly show that the effectiveness of our proposed model and this model consistents with the multi-access wireless network in future.

This study aimed to examine the vitamin D status of professional volleyball athletes and to determine its correlation with shoulder muscle strength. We finally included 52 healthy male professional volleyball players (23.2 ± 4.5 years), who were categorized by vitamin D status (<20 ng/mL: deficiency, 20-30 ng/mL: insufficiency, and >30 ng/mL: sufficiency). We examined the strength of the internal rotator (IR) and external rotator (ER) muscles of the shoulder by using isokinetic dynamometer. Fourteen players (26.9%) had vitamin D deficiency, 24 players (46.2%) were vitamin D insufficient, and 14 players (26.9%) were vitamin D sufficient. There was no significant correlation between the vitamin D level and shoulder muscle strength at 60°/s (IR, r = 0.159, p = 0.26; ER, r = 0.245, p = 0.08), and at 180°/s (IR, r = - 0.093, p = 0.51; ER, r = - 0.037, p = 0.79). Moreover, the isokinetic shoulder strengths were not significantly different across the three groups in all settings. In conclusion, vitamin D insufficiency was common in elite volleyball players. Though not being associated with isokinetic muscle weakness, vitamin D should be regularly monitored and supplemented in young elite athletes, considering its importance on musculoskeletal health.

We interviewed 48 people including local communities, ex hunters and protected area management professionals. The purpose of the interviews was to understand the motivations for, and the nature of, illegal hunting of prey species of iconic predators - tigers and leopards - in the northern section of Bardia National Park. Participants reported that hunting of prey species occurs mostly in spring and autumn and is less common during the summer. In the past, hunting was primarily for the purposes of obtaining meat for household consumption. Since the introduction of a road network in the region, opportunities to sell wild meat at ad-hoc ‘highway markets’ have developed. The purported medicinal properties of wild meat was also cited as a driver for illegal hunting. Mostly, locally hand-made guns are used for hunting and the use of dogs in hunting was often reported. Protected area managers informed that illegal hunting problems in the study area are associated with a lack of presence of park authorities, remoteness and underdevelopment and poverty of the community. Our study suggested that skills development training for local community members might reduce dependency on wild meat for household consumption and earning thereby reducing illegal hunting.

1) Background: In service business areas, design enhances the customer experience through the elements which anticipate specific emotional responses of customers. Many service companies are keen to develop and examine design elements from the customer perspective. Furthermore, recently, having considered the significance of customers’ emotional responses by design elements, categorising design elements into manageable dimensions can facilitate the evaluation of design elements. However, design elements and dimensions of design value are not defined in the current service marketing literature, and companies need a measurement tool and managerial guideline to their innovative value creation and compelling service delivery. For these reasons, this research aims to categorise the design value dimensions and propose the managerial implication for the innovative use of design; 2) Methods: This study used the mixed methodology; two stages of interviews and SEM (Structural Equation Modelling); 3) Results: Interview analyses facilitate the identification of design elements in the service delivery process. SEM results underpin the relevance of the categorised design elements and their impact on customer loyalty by comparing different groups (country and time elapsed from experience); and 4) Conclusions: Findings are the fundamentals of developing measuring tool for design and trigger future studies for conceptualising intangible assets.

Ongoing climate change causes abnormal climate events worldwide such as increasing temperatures and changing rainfall patterns. With South Korea facing growing damage from the increased frequency of localized heavy rains, the country is not an exception. In particular, its steep slope lands, including mountainous areas, are vulnerable to damage from landslides and debris flows. In addition, localized short-term heavy rains that occur in urban areas with extremely high intensity tend to lead a sharp increase in damage from soil-related disasters and cause huge losses of life and property. Currently, South Korea predicts landslides and debris flows using the standards for forecasting landslides and heavy rains. However, as the forecasting is conducted separately for rainfall intensity and accumulated rainfall, this lacks a technique that reflects both amount and intensity of rainfall in an episode of localized heavy rainfall. This study, therefore, aims to develop such a technique by collecting past cases of debris flow occurrences and rainfall events that accompanied debris flows to calculate the rainfall triggering index (RTI) reflecting accumulated rainfall and rainfall intensity. In addition, the RTI is converted into the critical accumulated rainfall (Rc) to use precipitation information and provide real-time forecasting. The study classifies the standards for flow debris forecasting into three levels: ALERT (10%–50%), WARNING (50%–70%), and EMERGENCY (70% or higher), to provide a nomogram for 6 hr, 12 hr, and 24 hr. As a result of applying this classification into the actual cases of Seoul, Chuncheon, and Cheongju, it is found that about 2–4 hr of response time is secured from the point of the Emergency level to the occurrence of debris flows.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

Recently, “mature” silkworms (MS) of Bombix mori have been considered as a potential nutraceutical, with a number of health benefits reported for steamed and lyophilized MS powder (SMSP). However, no obesity-related effects have been reported for SMSP. In the present study, anti-obesity effects of SMSP were investigated in adult mice in vivo, aged 12 weeks at the onset of drug administration, fed normal diet (ND) and high-fat diet (HFD), respectively, for 12 weeks. SMSP significantly suppressed body weight gain, intra-abdominal adipose tissue, and food efficiency in both ND-fed and HFD-fed adult mice. In addition, SMSP significantly decreased food intake and liver weight in HFD-fed mice, indicating that SMSP suppressed appetite and simultaneously reduced the conversion of feed into body weight in HFD-fed mice. SMSP also significantly lowered serum levels of glucose, triglyceride, total cholesterol, low-density lipoprotein cholesterol, asparagine transaminase, alanine transaminase, and alkaline phosphatase. However, SMSP had no significant effect on the weights of kidney, spleen, and thymus and serum levels of blood urea nitrogen and creatinine. Taken together, the above results suggest that SMSP has potent anti-obesity effects and is safe for long-term use as a potential therapeutic and/or nutraceutical in both obese patients and non-obese individuals.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

The incidence of right-turning pedestrian accidents is increasing in South Korea. Most of the accidents occurred when the larger vehicle was turning right, and the main cause of the accidents was found to be the driver's limited field of vision. After these accidents, the government has implemented a series of institutional measures with the objective of preventing such accidents. However, despite the institutional arrangements in place, pedestrian accidents continue to occur. We focused on the many limitations that autonomous vehicles, like humans, can face in such situations. To address this issue, we propose a right-turn pedestrian collision avoidance system by installing a LiDAR sensor in the center of the intersection to facilitate pedestrian detection. Furthermore, the urban road environment is considered, as this provides the optimal conditions for the model to perform at its best. During this research, we collected data on right-turn accidents using the CARLA simulator and ROS interface and demonstrated the effectiveness of our approach in preventing such incidents. Our results suggest that the implementation of this method can effectively reduce the incidence of right-turn accidents in autonomous vehicles.