Ongoing climate change causes abnormal climate events worldwide such as increasing temperatures and changing rainfall patterns. With South Korea facing growing damage from the increased frequency of localized heavy rains, the country is not an exception. In particular, its steep slope lands, including mountainous areas, are vulnerable to damage from landslides and debris flows. In addition, localized short-term heavy rains that occur in urban areas with extremely high intensity tend to lead a sharp increase in damage from soil-related disasters and cause huge losses of life and property. Currently, South Korea predicts landslides and debris flows using the standards for forecasting landslides and heavy rains. However, as the forecasting is conducted separately for rainfall intensity and accumulated rainfall, this lacks a technique that reflects both amount and intensity of rainfall in an episode of localized heavy rainfall. This study, therefore, aims to develop such a technique by collecting past cases of debris flow occurrences and rainfall events that accompanied debris flows to calculate the rainfall triggering index (RTI) reflecting accumulated rainfall and rainfall intensity. In addition, the RTI is converted into the critical accumulated rainfall (Rc) to use precipitation information and provide real-time forecasting. The study classifies the standards for flow debris forecasting into three levels: ALERT (10%–50%), WARNING (50%–70%), and EMERGENCY (70% or higher), to provide a nomogram for 6 hr, 12 hr, and 24 hr. As a result of applying this classification into the actual cases of Seoul, Chuncheon, and Cheongju, it is found that about 2–4 hr of response time is secured from the point of the Emergency level to the occurrence of debris flows.

Abstract: Imaging devices of less than 300,000 pixels are mostly used for sewage conduit exploration due to the petty nature of the survey industry in Korea. P articular ly , devices of less than 100,000 pixels are still widely used, and the environment for image processing is very bitter . Since the sewage conduit image s covered in this study ha ve a very low resolution (240 × 320 = 76,800 pixels), it is very difficult to detect cracks. Because most of the resolution of the sewe r conduit images are very low in Korea, this problem of low resolution was selected as the subject of study. Cracks were detected through a total of six steps of improving the crack in Step 2, finding the optimal threshold value in Step 3, and applying an algorithm to detect cracks in Step 5. Cracks were effectively detected by the optimal parameters in Steps 2 and 3 and the user algorithm in Step 5. Desp ite the very low resolution, the cracked image s showed 96.4% accuracy of detection, and the non cracked image s showed 94.5% accuracy . Moreover, the analysis was excellent in quality , also . It is believed that the findings of this study can be effectively u sed for crack detection with low resolution images.

This study surveyed the variation in Perfluorinated Compounds (PFCs) concentration entering urban wastewater treatment plants and proposed an optimal PFCS treatment method. The PFCS concentration in influent was shown to be affected by the types of industries and operating rate. The concentration of PFCs in the wastewater treatment effluent was slightly lower than that of influent. Thus, PFCs were considered to have barely been removed by the existing biological treatments. The pilot test result showed that about 10% of PFCs were removed by coagulation and precipitation, and the ozone and chlorine test also showed that few PFCs were removed regardless of the amount of injection. The activated carbon adsorption test showed that the removal was significantly increased by the empty bed contact time, with about a 60% removal in five minutes and over a 90% removal in 15 minutes. Therefore it is determined that a more stable and higher PFCs removal would result from the continuous oxidation processes such as ozone and adsorption processes such as activated carbon rather than a single biological treatment.

Prevention and management of cytomegalovirus (CMV) reactivation is important to improve outcome of allogeneic hematopoietic cell transplantation (allo-HCT) recipients. The aim of this study was to analyze real-world data for incidence and characteristics of CMV infections until 1-year after allo-HCT under 100-day letermovir prophylaxis. A single-center retrospective study was conducted between November 2020 and October 2021. During the study period, 358 patients underwent allo-HCT, 306 of whom received letermovir prophylaxis. Cumulative incidence of clinically significant CMV infection (CS-CMVi) was 11.4%, 31.7%, and 36.9% at 14-weeks, 24-weeks, and 1-year post-HCT, respectively. In multivariate analysis, risk of CS-CMVi increased with graft-versus-host disease (GVHD) ≥ grade 2 (adjusted odds ratio 3.640 [2.036–6.510]; P < 0.001). One-year non-relapse mortality was significantly higher in letermovir breakthrough CS-CMVi patients than those with subclinical CMV reactivation who continued letermovir (P = 0.002). There were 18 (15.9%) refractory CMV infection in this study population. In summary, letermovir prophylaxis is effective in preventing CS-CMVi until day 100, which increased after cessation of letermovir. GVHD is still a significant risk factor in letermovir prophylaxis era. Further research is needed to establish individualized management strategies especially in patients with significant GVHD or letermovir breakthrough CS-CMVi.

The purpose of this study is to analyze the causes of cost variation in natural disaster prevention projects (NDPP) in Gyeongsangbuk-do and to develop effective cost and risk management strategies. The study collected data by conducting an online survey of 244 stakeholders. Binary logistic regression was used to analyze the impact of various variables on cost deviation, in-cluding project management risk (PMR), project costing and execution risk (PCER), project exe-cution strategy risk (PESR), construction project risk (CPR), project cost and schedule risk (PCSR), project management challenges (PMC), and construction project subcontractor and safety man-agement (CPSSM). The results showed that PMR (OR=3.744, 95% C.I. [1.657, 8.457]), PCER (OR=5.068, 95% C.I. [2.236, 11.484]), PESR (OR=3.447, 95% C.I. [1. 853, 6.413]), CPR (OR=2.292, 95% C.I. [1.020, 5.151]), PCSR (OR=4.817, 95% C.I. [2.250, 10.317]), PMC (OR=2.954, 95% C.I. [1.452, 6. 013]), and CPSSM (OR=2.419, 95% C.I. [1.297, 4.515]) had statistically significant effects on cost deviation. In particular, PMR, PCER, and PESR were identified as the main causes, and the effects of additional factors such as CPSSM were also important. The developed predictive model plays an important role in helping stakeholders of NDPP to manage risks in advance and take appro-priate preventive measures to ensure the success of the project. This study empirically supports the theoretical hypotheses of previous studies and provides a clear understanding of the causes of cost deviation in NDPP, which provides important insights for strategic decision-making and provides a new perspective on risk management.

This study proposes self-calibration of capacitor mismatch errors for high-resolution pipeline analog-to-digital converters (ADCs). The proposed calibration circuit recursively amplifies the capacitor mismatch error by re-utilizing a multiplying digital-to-analog converter in a pipeline stage without increasing the circuit complexity, and the amplified error voltage is converted into digital code by utilizing the remaining pipeline stages. Error correction is performed by subtracting the digital code from the ADC output during normal operation. A prototype of a 12-bit pipeline ADC is fabricated in a 0.18 µm standard CMOS process. The ADC comprises eight 1.5-bit stages, followed by a 4-bit flash ADC as the final stage; the capacitor mismatch errors in the first two pipeline stages are corrected by utilizing the proposed self-calibration technique. At a sampling rate of 30 MS/s, the measured differential and integral nonlinearities improve from +0.82/-0.75 and +1.12/-1.79 to +0.45/-0.41 and +0.47/-0.91 after calibration, respectively. Further, the measured dynamic performances improve significantly with calibration. For an input frequency of 2.09 MHz, the ADC achieves a spurious-free dynamic range (SFDR) and signal-to-noise and distortion ratios (SNDR) of 69.3dB and 63.9dB before calibration, respectively. After calibration, the SFDR and SNDR increase to 84.1dB and 68.9dB, respectively, and the effective number of bits is approximately 11.1bit. The power consumption of the ADC is 35mW under 1.8V supply, and the resulting figure of merit is 514fJ/conversion step.

This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

An efficient design method is proposed for a compact common-mode rejection (CMR) filter utilizing dumbbell-shaped defected ground (DS-DG) structures and gap-coupled stub (GCS) resonators. A CMR filter for differential lines helps to improve the signal integrity of high-speed digital signals on printed circuit boards. The proposed CMR filter design is based on the equivalent circuit models, while the previous designs depended heavily on the DS-DG structure optimization using the EM simulations. The proposed CMR filter effectively reject the common-mode components with minimally affecting the differential signals. To prove the simplified design approach, a 5th-order Chebyshev band-stop filter has been designed with three DS-DG structures and two GCS resonators. From the simulated and measured results, it is found that the proposed CMR filter provides ~90% fractional frequency bandwidth with more than 20 dB of common-mode rejection ratio and less than 0.6 dB of insertion loss of the differential signal.

This study investigated changes in the average BMI of 5th and 6th grade elementary school students in Korea and provided foundational data to suggest the role of physical education for student health and set future directions. The 2019–2021 Physical Activity Promotion System (PAPS) of the Korean Ministry of Education was used. Data corresponding to 5th and 6th grade students (124,693 from 2019, 126,226 from 2020, and 117,809 from 2021) in 1,208 elementary schools in Korea were collected. The BMI was obtained by dividing weight by the square of height (㎏/m2). Repeated measures ANOVA was conducted for data analysis, and confidence intervals were modified through the Bonferroni correction for multiple comparisons. The Greenhouse-Geisser correction was used for effects test. The study findings are: First, the average BMI of 5th and 6th grade elementary school students in Korea increased significantly in 2021 compared to 2019 and 2020. Second, changes in the yearly average BMI showed a significant difference depending on gender and grade. Obesity among 5th and 6th grade elementary school students in Korea increased steadily in 2019–2021, which may be due to a decrease in students’ physical activity. Male students showed a steeper increase, regardless of grade.

A flavonoid Astragalin (kaempferol-3-O-β-D-glucopyranoside, Ast) has several biological activities including anti-oxidant, anti-HIV, and anti-allergic effects. Nonetheless, its insolubility in hydrophilic solvents imposes restrictions on its therapeutic applications. In this study, we investigated the effects of water-soluble astragalin-galactoside (kaempferol-3-O- β-D-isomaltotrioside, Ast-Gal) on dendritic cell (DC) maturation and T helper (Th) cell-mediated immune responses. Ast-Gal significantly increased maturation and activation of DCs through up-regulation of surface markers, such as CD80, CD86, and MHC II in a dose-dependent manner, while Ast had little effects. Also, Ast-Gal-treated DCs markedly secreted immune-stimulating cytokines such as IL-1β, IL-6, and IL-12. Importantly, Ast-Gal strongly increased expression of IL-12, a polarizing cytokine of Th1 cells. In a co-culture system of DCs and CD4+ T cells, Ast-Gal-treated DCs preferentially differentiates naïve CD4+ T cells into Th1 cells. The addition of neutralizing IL-12 mAb to cultures of Ast-Gal-treated DCs and CD4+ T cells significantly increased IFN- γ production, thereby indicating that Ast-Gal-stimulated DCs enhance the Th1 response through IL-12 production by DCs. Injection with Ast-Gal-treated DCs in mice increased IFN-γ-secreting Th1 cell population. Collectively, these findings indicate that hydrophilically modified astragalin can enhance Th1-mediated immune responses via DCs, and point to a possible application of water-soluble astragalin-galactoside as an immune adjuvant.

Bacterial communities in rhizosphere and root nodules have significant contributions to the growth and productivity of the soybean (Glycine max L.). In this report, we analyzed the physiological properties and dynamics of bacterial community structure in rhizosphere and root nodules at different growth stages using BioLog EcoPlate and high-throughput sequencing technology, respectively. The BioLog assay found that the metabolic capability of rhizosphere is in increasing trend in the growth of soybeans as compared to the bulk soil. As a result of the Illumina sequencing analysis, the microbial community structure of rhizosphere and root nodules was found to be influenced by the variety and growth stage of the soybean. At the phylum level, Actinobacteria were the most abundant in rhizosphere at all growth stages, followed by Alphaproteobacteria and Acidobacteria and the phylum Bacteroidetes showed the greatest change. But, in the root nodules Alphaproteobacteria were dominant. The results of the OTU analysis exhibited the dominance of Bradyrhizobium during the entire stage of growth, but the ratio of non-rhizobial bacteria showed an increasing trend as the soybean growth progressed. These findings revealed that bacterial community in the rhizosphere and root nodules changed according to both the variety and growth stages of soybean in the field.

Smartphone-based point-of-care testing (POCT) is rapidly emerging as an alternative to traditional screening and laboratory testing, particularly in resource-limited settings. In this proof-of-concept study, we present a smartphone- and cloud-based artificial intelligence quantitative analysis system (SCAISY) for relative quantification of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2)-specific IgG antibody lateral flow assays that enables rapid and accurate evaluation of test strips. By capturing an image with a smartphone camera, SCAISY quantitatively analyzes antibody levels and provides results to the user. We analyzed changes in antibody levels over time in over 248 individuals, including vaccine type, number of doses, and infection status, with a standard deviation of less than 10%. We also tracked antibody levels in six participants before and after SARS-CoV-2 infection. Finally, we examined the effects of lighting conditions, camera angle, and smartphone type to ensure consistency and reproducibility. This study suggests that SCAISY is a simple and powerful tool for real-time public health surveillance, enabling the acceleration of quantifying SARS-CoV-2-specific antibodies generated by either vaccination or infection and tracking of personal immunity levels.

Cancer treatment is a significant focus in medicine owing to the increasing global incidence. Patients with advanced cancers that do not respond to conventional therapies have limited options and an unfavorable prognosis. Consequently, researchers are investigating complementary approaches to conventional treatments. One such approach is alkalization therapy, which aims to neutralize the acidic tumor microenvironment (TME) by increasing its pH level. The acidic TME promotes inflammation, tumor progression, and drug resistance. Alkalization therapy has been demonstrated to be effective for various cancers. In addition, natural products, such as triterpenoids, parthenolides, fulvic acid, Taxus yunnanensis, and apple pectin have the potential to alleviate symptoms, maintain physical fitness, and improve treatment outcomes of cancer patients through their anti-inflammatory, antioxidant, and anticancer properties. In this review, we focus on the effects of alkalization therapy and natural products on cancer. Furthermore, we present a case series of advanced cancer patients who received alkalization therapy and natural products alongside standard treatments, resulting in long-term survival. We posit that alkalization therapy together with the supplementation of natural products may confer benefits to cancer patients by mitigating the side effects of chemotherapy and complementing standard treatments. However, further research is warranted to validate these clinical findings.

A short review of the important studies was conducted to evaluate the potential of aerosol transmission of the Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2). The minimum size of droplets potentially carrying the SARS-CoV-2 was newly estimated and discussed in this review.

We previously found a novel a new sirtuin (SIRT) inhibitor MHY2256 that exerts anticancer activity through p53 acetylation in MCF-7 human breast cancer cells. Here, we investigated the anticancer activity of MHY2256 against hormone-related cancer, which is an endometrial cancer with poor prognosis. We found that MHY2256 markedly reduced cellular proliferation at low concentrations against Ishikawa endometrial cancer cells. The IC50 values of MHY2256 were much lower than that of salermide. Furthermore, MHY2256 significantly reduced the protein expression and activities of SIRT1, 2, and 3 with similar effects as salermide, a well-known SIRT inhibitor. Particularly, MHY2256 markedly inhibited tumor growth in a tumor xenograft mouse model of Ishikawa cancer cells. During the experimental period, there was no significant change in the body weight of mice treated with MHY2256. Detailed analysis of the sensitization mechanisms of Ishikawa cells revealed that late apoptosis was largely increased by MHY2256. Additionally, MHY2256 increased G1 arrest and reduced cell cyclic-related proteins, suggesting that apoptosis by MHY2256 was achieved by cellular arrest. Particularly, p21 was greatly increased by MHY225656, suggesting that cell cycle arrest by p21 is a major factor in MHY2256 sensitization in Ishikawa cells. We also detected a significant increase in acetylated p53, a target protein of SIRT1, in Ishikawa cells after MHY2256 treatment. In a mouse xenograft model, MHY2256 significantly reduced tumor growth and weight without apparent side effects. These results suggest that MHY2256 exerts its anticancer activity through p53 acetylation in endometrial cancer and can be used for targeting hormone-related cancers.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

The calmodulin-binding transcription activators (CAMTAs) mediate transcriptional regulation of development, growth, and responses to various environmental stresses in plants. To characterize the biological processes of soybean CAMTA (GmCAMTA) family members in response to abiotic stress, we identified 15 GmCAMTA genes from soybean (Glycine max L.) and investigated their roles in the abiotic stress response. The transcriptions of GmCAMTAs exhibited distinct circadian regulation patterns and were expressed differently in response to salt, drought, and cold stresses, except ABA. Interestingly, the expression levels of GmCAMTA2, GmCAMTA8, and GmCAMTA12 were higher in stem tissue than in other soybean tissues. To determine the roles of GmCAMTAs in the regulation of developmental processes and stress responses, we isolated GmCAMTA2 and GmCAMTA8 cDNAs from soybean and generated Arabidopsis overexpressing transgenic plants. The GmCAMTA2-OX and GmCAMTA8-OX plants showed hypersensitivity to drought stress. The water in the leaves of GmCAMTA2-OX and GmCAMTA8-OX plants was lost faster than that in WT plants under drought stress conditions. In addition, stress-responsive genes in the GmCAMTA2-OX and GmCAMTA8-OX plants were down-regulated under drought stress conditions. Our results suggest that GmCAMTA2 and GmCAMTA8 genes are regulated by circadian rhythms and function as negative regulators in development and drought stress responses.

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

Obesity, which is characterized by an excessive accumulation of body fat, is one of the critical factors causing metabolic syndrome. Many studies have been performed to identify appropriate agents to control obesity, but toxicity remains a problem. Herein, we identified that phenylbutyrate (PBA), which has been used to treat urea cycle disorder with very low toxicity for a long time, efficiently inhibited high fat-induced body weight gain in a diet-induced obesity mouse model (DIO model). PBA treatment decreased body fat mass and increased lean composition. Moreover, PBA increased brown adipose tissue (BAT) activity by increasing glucose uptake, thereby improving glucose tolerance and insulin tolerance. Interestingly, PBA could induce the expression of phosphofructokinase (PFKL), a key enzyme in the glycolytic pathway, and knocking down PFKL dramatically repressed the expression level of Ucp1 as well as those of Prdm16, Cidea, Pgc1α, and Pparγ, which are marker genes for BAT activation. These results strongly suggested that PBA could increase energy expenditure by increasing BAT activity via the induction of PFKL. Taken together, PBA could be used as a therapeutic agent for people with obesity to prevent the development of metabolic syndrome.

We investigate the behavior of the partial derivative approach to the change of scale formula and prove relationships among the analytic Wiener integral and the analytic Feynman integral of the partial derivative for the function space integral.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

Abstract The aim of our study is to analyse the perception of the families and concerned social workers. The research was conducted in an underprivileged and disadvantaged microregion in North Hungary. The main focus was the perception on the available health, educational, child welfare and social services and supports. The starting point was to enquire the target group’s knowledge of these services. The study examines the extent to which social work is able to provide support to disadvantaged, marginalized families with children, and the way how the dysfunctional operation of the system contributes to the perpetuation of the clients’ life conditions. Analysing the quality of these services and supports is crucial to understand the social mobility chance of the children living in this microregion. The results show that without capability and talent development for the children and given the lack of welfare services, the mobility chance and opportunities of these families are extremely low in Hungary.

Pyruvate kinase M2 (PKM2) is essential for aerobic glycolysis and is highly expressed in various cancer tissues. Although high PKM2 expression is observed in prostate cancer tissues, its functional role in cancer metabolism is unclear. Here, we investigated the role of PKM2 in regulating autophagy and its associated pathways in prostate cancer cells. PKM2 expression was silenced using various PKM2 small interfering RNAs (siRNAs) and then we measured PKM2-related cellular pathways associated with autophagy. PKM2 siRNA-transfected prostate cancer cells showed significantly reduced viability. Acridine orange staining and immunoblotting analysis showed that PKM2 downregulation markedly increased autophagic cell death. Results of western blotting analysis showed that PKM2 knockdown affected protein kinase B/mechanistic target of rapamycin 1 pathway, which consequently downregulated the expression of glycolytic enzymes lactate dehydrogenase A and glucose transporter 1. To the best of our knowledge, this is the first study to show that PKM2 inhibition alters cancer cell metabolism and induces autophagy. Thus, the present study provides a strategy for the development of PKM2-targeted novel anticancer drugs for the treatment of prostate cancer.

Computer and Smart Device-assisted Learning (CSDL) has gained increasing attention from educational researchers and practitioners in recent years. However, it remains controversial whether student can benefit from CSDL and what moderator could affect the impact of CSDL. Within the specific context of Korea, where the interest in digital education is steadily increasing, the number of empirical studies exploring the causal effect of CSDL remains relatively scarce. The primary objective of this empirical study was to investigate the impact of CSDL on students' academic achievement in Korea. To achieve this objective, a two-way fixed effect model was employed, utilizing a panel dataset spanning three years derived from the 'Korean Education Longitudinal Study 2013'. The findings revealed a significant positive impact of CSDL on students’ Mathematics achievement. Notably, higher income levels, increased availability of computer resources provided by schools, and the implementation of more individualized education were identified as factors that moderate the effect of CSDL on students' achievement levels in Korean and English subjects. These findings underscore the need for an approach that optimizes the educational benefits of CSDL by considering subject-specific characteristics. Furthermore, this study highlights the importance of allocating educational resources, such as computers and smart devices, and integrating individualized educational activities within the classroom environment.

Abstract: Cancer survivors are at an increased risk for cardiovascular disease (CVD). However, the association between particulate matter (PM) and CVD risk among cancer survivors (alive >5 years since diagnosis) is unclear. We investigated the risk of CVD among 40,899 cancer survivors within the Korean National Health Insurance Service database. Exposure to PM was determined by assessing yearly average PM levels obtained from the Air Korea database from 2008 to 2011. PMs with sizes <2.5 (PM2.5), <10 (PM10), or 2.5-10 (PM2.5-10) μm in diameter were compared, with each PM level exposure further divided into quintiles. Patients were followed up from January 2012 to date of CVD event, death, or December 2017, whichever came earliest. Adjusted hazard ratios (aHRs) and 95% confidence intervals (CIs) for CVD were calculated using Cox proportional hazards regression by PM exposure levels. Compared with cancer survivors in the lowest quintile of PM2.5 exposure, those within the highest quintile had a greater risk for CVD (aHR 1.31, 95% CI 1.07-1.59). Conversely, increasing PM10 and PM2.5-10 levels were not associated with increased CVD risk (p for trend 0.078 and 0.361, respectively). Cancer survivors who reduce PM2.5 exposure may reduce their risk of developing CVD.

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p&lt;.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p&lt;.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p&lt;,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

The geographical environment, food culture, and dietary habits are substantially different between the southern and northern regions in China. We investigated the associations with dietary patterns and metabolic syndrome between Chinese adult from the southern and northern regions (North: 1249; South: 1849) using data from the Chinese Health and Nutrition 2009 survey. Respectively, four dietary patterns were identified by factor analysis in the two regions. Each dietary pattern of factor score was calculated for three groups by tertile (T1<T2<T3). In the northern region, the association between the Alcohol and Western pattern and the risk of abdominal obesity (OR: 1.31; 95%:1.01, 1.68), hypertriglyceridemia (OR: 1.35; 95%:1.05, 1.74), high fasting blood glucose (OR: 1.37; 95%: 1.05, 1.80), and hypertension (OR: 1.55; 95%: 1.45, 1.99) was increased. In the southern region, the Convenience Food pattern was positively associated with hypertriglyceridemia (OR: 1.53; 95%: 1.03, 2.26), low HDL-cholesterol (OR: 1.96; 95%: 1.12, 3.43), and metabolic syndrome (OR: 1.79; 95%: 1.03, 3.11). The Alcohol dietary pattern was positively associated with high fasting blood glucose (OR: 1.83, 95%: 1.13, 2.97). There are some dietary pattern differences in the two regions. It is necessary to consider the factors of food culture and food intake habits in order to provide nutrition education to Chinese individuals from different regions in the future.

If an algebra of type $A$ contains a subalgebra which is also an algebra of type $B$, then it is a Smarandache $B$-type $A$-algebra provided the subalgebra of type $B$ contains at least two elements. This generalizes the notion of Smarandache group, where the group of order $\geq 2$ is a subsemigroup of a semigroup. In this paper we investigate a number of such pairings and we deduce a number of conclusions as a consequence.

In this paper, we observe that if X is a set and (Bin(X), □) is the semigroup of binary systems on X, then its center ZBin(X) consists of the locally-zero-semigroups and that these can be modeled as (simple) graphs and conversely. Using this device we show that we may obtain many results of interest concerning groupoids by reinterpreting graph theoretical properties and at the same time results on graphs G may be obtained by considering them as elements of centers of the semigroups of binary systems (Bin(X), □) where X = V(G), the vertex set of G.

We studied the dynamics of stable carbon (δ13C) and nitrogen (δ15N) isotopes in litters from Norway spruce (NSL) (Picea abies) and Scots pine (SPL) (Pinus silvestris) during in situ decomposition over a period of more than 4 years. Relative to initial values, δ13CNSL showed a weak enrichment (0.33‰), whereas δ13CSPL resulted in depletion (-0.74‰) at the end of decomposition. Both litter types experienced a depletion in δ15N during decomposition; δ15NNSL decreased by -1.74‰ and δ15NSPL decreased by -1.99‰. The effect of the selective preservation of or acid unhydrolyzable residue (AUR) in lowering δ13C of the residual litter was evident only in SPL. In the NSL, only in the initial stage C/N had a large effect on the δ13C values. In the later stages, there was a non-linear decrease in δ13CNSL with a simultaneous increase in AUR concentrations , but the effect size was large, suggesting the role of lignin in driving δ13C of residues in later stages. Depletion in 15N of the residual litters concomitant with the increase in N concentration suggests bacterial transformation of the litter over fungal components. A consistent decline in δ15N values further implies that bacterial dominance prompted this by immobilizing nitrate depleted in 15N in the residual litter.

Alzheimer’s disease (AD) and type 2 diabetes mellitus (T2DM) are comorbidities that result from the sharing of common genes. The molecular background of comorbidities can provide clues for the development of treatment and management strategies. Here, the common genes involved in the development of the two diseases and in memory and cognitive function are reviewed. Network clustering based on protein-protein interaction networks identified tightly connected gene clusters that have an impact on memory and cognition among the comorbidity genes of AD and T2DM. Genes with functional implications were intensively reviewed, and relevant evidence was summarized. Gene information will be useful in the discovery of biomarkers and the identification of therapeutic targets for AD.

This study investigates the specific factors affecting the usage intention of distributed ledger technology (DLT), such as availability, diversity and economic value from the perspective of a unified theory of technology acceptance. Users of DLT in public and private sectors were surveyed. Availability and economic value affect performance expectancy, while availability, diversity, and profitability have an influence on effort expectancy. Performance expectancy and transparency have a positive effect on the intention to use DLT which in turn exerts a positive effect on usage behavior. This study provides implications for researchers in that it attempts to investigate the factors affecting the usage intention of DLT based on the extended unified theory of acceptance and encompassing diverse industries that adopt DLT, such as the public, financial, medial, and logistics sectors.

Serum carbohydrate antigen 19-9 (CA19-9) levels can increase in nontuberculous mycobacteria pulmonary disease (NTM-PD) and the levels correlate with disease activity. We compared the clinical characteristics of NTM-PD patients with and without elevated CA19-9 levels and evaluated its association with the antibiotic response in a retrospective study of NTM-PD patients diagnosed between January 1994 and December 2020. We analyzed 1,112 patients who had serum CA19-9 measured: 322 with elevated CA19-9 and 790 with normal CA19-9. The erythrocyte sedimentation rate and C-reactive protein levels were significantly higher in the elevated CA19-9 group (p < 0.001 and p = 0.029, respectively). The 1-year culture conversion rate after antibiotics did not differ between the elevated (n = 206) and normal (n = 377) CA19-9 groups (80% vs. 72%, p = 0.055). Analysis of a subset of 434 patients revealed that current smoking, bronchiectasis, acid-fast bacilli smear positivity, and the M. abscessus strain significantly reduced microbiological cure rates. Serum CA 19-9 levels did not have a significant association with microbiological cure in a multivariate analysis. These findings suggest that the role of serum CA19-9 in predicting antibiotic treatment outcomes is limited, and that elevated CA19-9 does not necessarily indicate a poor outcome.

Metabolic-associated fatty liver disease (MAFLD) and diabetic kidney disease (DKD) share various pathophysiological factors, and epidemiological evidence suggests that these two diseases are associated. Albuminuria and the estimated glomerular filtration rate, which are conventional biomarkers of DKD, are reportedly associated with the risk or severity of MAFLD. Recently, novel DKD biomarkers reflecting renal tubular injury have been introduced to complement conventional DKD markers. In this article, we looked at previous studies that showed an association between MAFLD and DKD and also reviewed the significance of DKD biomarkers as predictive risk factors for MAFLD.

We produced a recombinant eel luteinizing hormone (rec-eel LH) analog with high potency in Chinese hamster ovary DG44 (CHO DG44) cells. The eel LH mutant (LH-M), which had a linker comprising the equine chorionic gonadotropin (eCG) β-subunit carboxyl-terminal peptide (CTP) region (amino acids 115 to149), was inserted between the β-subunit and α-subunit of wild-type tethered eel LH (LH-wt). Monoclonal cells transfected with the eel LH-wt and eel LH-M plasmids were isolated from five and nine clones of CHO DG44 cells, respectively. The secreted quantities abruptly increased on day 3, with peak levels of 5,000–7,500 ng/mL on day 9. The molecular weight of eel LH-wt was 32–36 kDa while that of eel LH-M increased to approximately 38–44 kDa, indicating the detection of two bands. Treatment with peptide N-glycanase F decreased the molecular weight by approximately 8 kDa. The oligosaccharides at the eCG β-subunit O-linked glycosylation sites were appropriately modified post-translation. The EC50 value and maximal responsiveness of eel LH-M increased by approximately 2.90- and 1.29-fold, respectively, indicating that the mutant exhibited more potent biological activity than eel LH-wt. Phosphorylated extracellular regulated kinase (pERK1/2) activation resulted in a sharp peak 5 min after agonist treatment, with a rapid decrease thereafter. These results indicate that the new rec-eel LH analog which contains the eCG β-subunit CTP linker comprising O-linked glycosylation sites, had more potent activity than the wild-type in vitro. Taken together, this new eel LH analog can be produced in large quantities using a stable CHO DG44 cell system.

This study aimed to produce single-chain recombinant eel follicle-stimulating hormone (rec-eel FSH) analogs with high activity in Chinese hamster ovary DG44 (CHO DG44) cells. We recently reported that an O-linked glycosylated carboxyl-terminal peptide (CTP) of the equine chorionic gonadotropin (eCG) β-subunit plays contributes on high activity and time-dependent secretion in mammalian cells. We constructed a mutant (FSH-M) in which a linker including the eCG β-subunit CTP region (amino acids 115 to149) was inserted between the β-subunit and α-subunit of wild-type single chain eel FSH (FSH-wt). Plasmids containing eel FSH-wt and eel FSH-M were transfected into CHO DG44 cells. Single cells expressing each protein were isolated from 10 and 7 clones, respectively. Secretion increased gradually during the cultivation period and peaked at 4,000–5,000 ng/mL on day 9. The molecular weight of eel FSH-wt was 34–40 kDa, while that of eel FSH-M increased substantially, with two bands at 39–46 kDa. Treatment with PNGase F to remove the N glycosylation sites decreased the molecular weight remarkably to approximately 8 kDa. The EC50 value and maximal responsiveness of eel FSH-M were approximately 1.23- and 1.06-fold higher than those of eel FSH-wt, indicating that the mutant showed slightly higher biological activity. Phosphorylated extracellular regulated kinase (pERK1/2) activation exhibited a sharp peak at 5 min, followed by a rapid decline. These findings indicate that the new rec-eel FSH molecule with the eCG β-subunit CTP linker showed potent activity and could be produced in massive quantities using the stable CHO DG44 cell system.

We identified a novel heterozygous hypofibrinogenemia, γY278H (Hiroshima). To demonstrate the cause of reduced plasma fibrinogen levels (functional level: 1.12 g/L and antigenic level: 1.16 g/L), we established γY278H fibrinogen-producing Chinese hamster ovary (CHO) cells. An enzyme-linked immunosorbent assay demonstrated that synthesis of γY278H fibrinogen inside CHO cells and secretion into the culture media were not reduced. Then, we established an additional five variant fibrinogen-producing CHO cell lines (γL276P, γT277P, γT277R, γA279D, and γY280C) and performed further investigations. We have already established 33 γ-module variant fibrinogen-producing CHO cell lines including 6 cell lines in this study, but only the γY278H and γT277R cell lines showed disagreement, namely recombinant fibrinogen production was not reduced but the patients’ plasma fibrinogen level was reduced. Finally, we performed fibrinogen degradation assays and demonstrated that the γY278H and γT277R fibrinogens were easily cleaved by plasmin whereas their polymerization in the presence of Ca2+ and “D:D” interaction was normal. In conclusion, our investigation suggested that patient γY278H showed hypofibrinogenemia because γY278H fibrinogen is secreted normally from the patient’s hepatocytes but had accelerated degradation by plasmin in the circulation.

The purpose of this study was to assess the extent to which self-esteem and depression mediated the influence of internalized stigma on life satisfaction among Korean out-of-school youths. Cross-sectional data on 318 youths provided information on perceived stigma, self-esteem, depression, life satisfaction, and personal characteristics. A multinomial logistic regression analysis was followed by structured path analysis to investigate the mediation effects. Internalized stigma was negatively associated with life satisfaction. Self-esteem significantly mediated the influence of stigma on depression and the influence of depression on life satisfaction. Further, stigma directly and significantly influenced depression. This study demonstrated that self-esteem and depression were important to the relationship between internalized stigma and life satisfaction. Implications for possible policies and programs with the aim of helping out-of-school youths to integrate and lead successful satisfying lives are discussed.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

Individual investors often struggle to predict stock prices due to the limitations imposed by the computational capacities of personal laptop Graphics Processing Units (GPUs) when running intensive deep learning models. This study proposes solving these GPU constraints by integrating deep learning models with technical analysis methods. This integration significantly reduces analysis time and equips individual investors with the ability to identify stocks that may yield potential gains or losses in an efficient manner. Thus, a comprehensive buy and sell algorithm, compatible with average laptop GPU performance, is introduced in the study. This algorithm offers a lightweight analysis method that emphasizes factors identified by technical analysis methods, thereby providing a more accessible and efficient approach for individual investors. To evaluate the efficacy of this approach, we analyzed the performance of eight deep learning models: LSTM (4 layers), CNN, BiLSTM (4 layers), CNN Attention, BiGRU CNN BiLSTM Attention, BiLSTM Attention CNN, CNN BiLSTM Attention, and CNN Attention BiLSTM. These models were used to predict stock prices for Samsung Electronics and Celltrion Healthcare. The CNN Attention BiLSTM model displayed superior performance among these models, with the lowest validation mean absolute error value. In addition, an experiment was conducted using WandB Sweep to determine the optimal hyperparameters for four individual hybrid models. These optimal parameters were then implemented in each model to validate their back-testing rate of return. The CNN Attention BiLSTM hybrid model emerged as the highest-performing model, achieving an approximate rate of return of 5 percent. Overall, this study offers valuable insights into the performance of various deep learning and hybrid models in predicting stock prices. These findings can assist individual investors in selecting appropriate models that align with their investment strategies, thereby increasing their likelihood of success in the stock market.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

A systematic approach for model updating using the modal identification results is proposed. Modal identification provides mode shapes for physical quantities (acceleration strain, etc.) measured in specific directions at the location of the sensors. Besides, model updating involves the use of the mode shapes related to the nodal degrees-of-freedom of the finite element analytic model. Consequently, the mode shapes obtained by modal identification and the mode shapes of the model updating process do not coincide even for the same mode. Therefore, a method constructing transform matrices that distinguish the cases where measurement is done by acceleration, velocity and displacement sensors and the case where measurement is done by strain sensors is proposed to remedy such disagreement between the mode shapes. The so-constructed transform matrices are then applied when the mode shape residual is used as objective function or for mode pairing in the model updating process. The feasibility of the proposed approach is verified by means of a numerical example in which the strain or acceleration of a simple beam is measured and a numerical example in which the strain of a bridge is measured. Using the proposed approach, it is possible to model the structure regardless of the position of the sensors and to select the location of the sensors independently from the model.

In this paper, we introduce the partially degenerate Changhee-Genocchi polynomials and numbers and investigated some identities of these polynomials. Furthermore, we investigate some explicit identities and properties of the partially degenerate Changhee-Genocchi arising from the nonlinear dierential equations.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

Kim-Kim ([9]) studied some properties of the degenerate gamma and degenerate Laplace transformation and obtained their properties. In this paper, we define modified degenerate gamma and modified degenerate Laplace Transformation and investigate some properties and formulas related to them.

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

Synthetic polymer-based gradient foams have considered as promising category of functionally graded materials with unique properties. In this study, the carbon dioxide (CO₂) foaming technology has used for PET-PEN (Polyethylene Terephthalate - Polyethylene Naphthalate) copolymer towards porous functional materials with thermal insulation with reasonable mechanical strength. Through scanning electron microscope based morphological characterization, a potential to fabricate gradient foam structures with micro-pores has identified. It has shown that variation of post-foaming temperature can tune the pore size distribution although the very high post-foaming temperature tends to cause structural instability. Thermal measurement data set the limits of operation, confirmed by simultaneous differential scanning calorimeter and thermo-gravimetric analysis. Mechanical stress and thermal conductivity also has measured to find rationale of thermal insulation with reasonable mechanical strength and to elucidate the actual 3D grid foam of copolymer.

This study aimed to identify the most beneficial attitudes adopted by enterprise participants during their engagement in open-source software (OSS) activities. For this purpose, we selected repositories from GitHub, featuring the top 10 with the highest stars and forks, classified the participants according to their sentiment states, and compared their productivity. The results indicated that participants with positive sentiments were more productive than those with negative sentiments. Consequently, it can be inferred that encouraging organizations to express positive sentiments towards their developers publicly may stimulate OSS community activities and enhance productivity, thereby potentially leading to increased open innovation and sustainability.

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

Background: Albumin has a pivotal role in the homeostasis of osmotic pressure and is associated with cardiovascular, nephrotic, hepatic, and nutritional diseases. The detection of hypoalbuminemia is a cornerstone for diagnosis of hidden diseases and patient deterioration. We developed and validated a deep-learning-based model (DLM) for detection of hypoalbuminemia using electrocardiography (ECG). Methods: This historical cohort study included data from consecutive patients from two hospitals. The patient data in one hospital were divided into development (82,499 ECGs from 54,248 patients) and internal validation (20,664 ECGs from 20,664 patients) datasets, whereas the patient data in the other hospital were included in only an external validation (37,421 ECGs from 37,421 patients) dataset. An DLM was developed using a 12-lead ECG signal, age, and sex from the development dataset. The endpoint was hypoalbuminemia, defined by serum albumin concentration below 3.5 g/dL. Results: During the internal and external validations, the areas under the receiver operating characteristic curve of the DLM for the detection of hypoalbuminemia were 0.887 (0.877–0.897) and 0.888 (0.880–0.896), respectively. Among the 27,400 individuals without hypoalbuminemia at the initial laboratory exam, those identified by the DLM as higher-risk patients had a significantly larger change in developing hypoalbuminemia than those in the low-risk group (7.09% vs. 1.01%, p < 0.001) during 24 months. The sensitivity map showed that the DLM focused on the T wave and QRS complex for the detection of hypoalbuminemia. Conclusions: The DLM exhibited a high accuracy for hypoalbuminemia detection and prediction using 12-, 6-, and single-lead ECGs.

Incident rates of neurodegenerative diseases have steadily increased globally, but there is no therapeutic access available. We newly prescribed medicinal herbal remedy including five different herbal plants called, Chen-Ma-Dan-Sam-Ga-Mi-Bang (CMST), purposed to prove for pharmacological properties and corresponded actions on hippocampus neuronal cell injury by hypoxia-induced mice model. Mice were adapted to normoxia or hypoxia with or without CMST for 5 days. We gathered pharmacological effects of CMST on cell injury by enhancement of dihydroethidium and 4-hydroxynonenal signals which were correlated with abnormal redox status in the protein or gene expression levels (abnormal elevations of nitric oxide, reactive oxygen species, lipid peroxidation and deteriorations of total glutathione, total antioxidant capacity, and activities of superoxide dismutase and catalase) due to hypoxia. CMST also notably exerted to attenuates molecules for neuronal cell injury markers such as p-tau, cleaved caspase-3 due to DNA oxidations (53bp1and phosphor-histone H2AX), inflammatory cytokines, and hemeoxigenase-1. We further figured out the underlying actions of CMST by in vitro experiment through inactivation of microglial cell which can mediate neuronal cell injury. Collectively, CMST prevented from hippocampal neuronal cells via inactivation of microglial cell with normalization of redox status on hypoxia-induced hippocampus neuronal cell injury.

In order to realize the tram's low-floor structure, most of the trams that have been recently introduced adopt an independently rotating wheelset. In the case of trains driving in two regions with different gauges, an independently rotating wheelset may be applied to utilize the variable track technology. Since the independent rotation type wheelset has no rotational restraint of the left and right wheels, the difference in rotational speed between the outer and inner wheels occurs naturally during curved driving, and it is applied to railroad vehicles traveling in steep curve sections because it smoothly drives curved driving. However, the longitudinal creep force and the lateral restoring force are weakened as the left and right rotational constraints disappear. Lack of transverse direction restoring force weakens stability while causing continuous flange contact driving or zigzag phenomenon against disturbance. Under the conditions of driving in a steep curve, these railway vehicles generate excessive wear, noise, and lateral pressure, as well as deterioration of ride comfort and derailment. In order to overcome these drawbacks, a method has been proposed in which the torque of a motor mounted on each wheel is individually controlled to generate lateral restoring force or to improve driving performance through lateral displacement control using a yaw moment. In this paper, development using HILs was performed to check the performance and stability of the individual motor torque control technology before verifying by applying the individual motor torque control to the actual vehicle. HILs were constructed by combining a real-time dynamic analysis model of a railway vehicle with a drive motor to which real individual motor control was applied. Under the conditions of driving the test track where the actual test vehicle was tested, the analysis of the driving characteristics and the control characteristics of the disturbance was performed to confirm the proposed individual motor torque control performance.

Using a variety of theoretical foundations, this paper examines the association between corporate social responsibility (CSR) and employees’ knowledge-sharing behavior, investigating the sequential mediation role of perceived organizational support and organizational commitment as well as the moderating role of ethical climate. Hypotheses were formulated to address both the sequential mediation effect of perceived organizational support and organizational commitment on the link between CSR and knowledge-sharing and the moderation effect of ethical climate on the relationship between CSR and perceived organizational support. In order to mitigate the problems of potential common method bias, data were gathered from a sample of 204 South Korean employees at three distinct time points. The results of the study offer compelling evidence that CSR activities exert a positive influence on employees’ knowledge-sharing behavior, an effect that is sequentially mediated by both perceived organizational support and organizational commitment. Furthermore, the research uncovers the positive moderating role played by ethical climate in the relationship between CSR and perceived organizational support. By integrating multiple theoretical frameworks, this study not only advances the extant literature but also offers invaluable insights for organizations striving to bolster knowledge-sharing through the strategic implementation of CSR initiatives.

In this work, polyacrylic acid-functionalized MCM-41 was synthesized, which was further interacted with calcium ions, to realize enhanced pH-responsive nanocarrier for sustained drug release. First, mesoporous silica nanoparticles (MSNs) were prepared by the sol-gel method. Afterward, (3-trimethoxysilyl)propyl methacrylate (TMSPM) modified surface was prepared by using the post-grafting method, then polymerization of acrylic acid was proceeded. After adding calcium chloride solution, polyacrylic acid-functionalized MSNs with calcium-carboxyl ionic bonds in the polymeric layer, which can prevent the cargo from leaking out of the mesopore, were prepared. The structure and morphology of the modified nanoparticles (PAA-MSNs) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, etc. The controlled release of guest molecules was studied by using 5-fluorouracil (5-FU). The drug molecules-incorporated nanoparticles showed different releasing rates under different pH conditions. It is considered that our current materials have the potential as pH-responsive targeted nanocarriers in the field of medical treatment.

In this paper, we investigate the effects of certain variants of the commutative laws on properties of several families of algebras which are in general not commutative, such as groups, linear algebras, or actually quite anti-commutative, such as $BCK$-algebras and $d$-algebras among others. From results obtained it becomes clear that by considering these variants in the presence of yet other axioms it is to be expected that a quite rich and varied set of results may be obtained both in the general and the particular setting of which what has been accomplished in this paper is a substantial sample.

As climate is not only a valuable tourism resource but also a factor influencing travel experience, estimating climate change can provide implications to sustainable development of the tourism industry. This study develops Climate Volatility Index (CVI) using GARCH model and estimates the relationship between CVI and Japanese tourism demand for Korea using a tourism demand model, based on data from January 2000 to December 2013. Time lag is applied based on a decision making process regarding travel destinations. The result shows that an increase in volatility of climate change leads to a decrease in tourism demand.

The modeling of flood-induced bend scour near embankment toes can provide important information for river engineering, embankment safety warnings, and emergency action management. During the rainy seasons, short-term general scour and bend scour are the most common causes for the failure of reinforced concrete embankments in Taiwan. To gain a deeper understanding of the scouring process near levee foundations, this study proposed a straightforward and practical method for bend scour simulation. The proposed simulation method is subdivided into three stages: two-dimensional flow simulation, general scour estimation, and bend scour estimation. A new bend-scour computation equation is proposed and incorporated into a two-dimensional hydraulic finite-volume model for simulating the evolution of bend scour depth around embankment toes. The proposed method is applied to simulate the temporal evolution of bend scouring near the Shuideliaw Embankment on the Cho-Shui River in Taiwan, where serious failure occurred during the June 2012 monsoon. Field data were gathered using the numbered-brick technique at the Shuideliaw Embankment to demonstrate the accuracy of the proposed method. The results of the bend scour simulations compared reasonably well with field measurements, indicating close agreement in terms of water levels and bend scour depths near the Shuideliaw Embankment. The proposed method was found to quickly estimate the maximum short-term general scour and bend scour depths for further enhancement of the safety of the embankment toe.

This study examines the impact of executives implicated in fraud on firms' investment decisions using AAERs in the US, aiming to address the underexplored aspect of rationalization within the fraud triangle. Executives implicated in fraud often display abnormal attitudes to justify accounting irregularities, prompting an investigation into how abnormal investment decisions are used for rationalizing fraud, given their critical role in a firm's long-term sustainability. Analysis of AAERs spanning from 1981 to 2013 reveals that implicated executives, particularly CEOs and CFOs, tend to make abnormal investment decisions, and that collusive fraud exacerbates this behavior. Notably, such executives lean towards overinvestment, particularly in R&amp;D expenditures, to hide or justify fraud; the duration of fraud amplifies its impact on investment decisions. By shedding light on the rationalization aspect of the fraud triangle, this research contributes valuable insights for investors, regulators, and academia emphasizing the significance of public disclosure of fraud to enhance transparency in capital markets and the importance of ethics-focused education in accounting to prevent corporate fraud.

Precise binding affinity predictions are essential for structure-based drug discovery (SBDD). Focal adhesion kinase (FAK) is a member of the tyrosine kinase protein family and is overexpressed in a variety of human malignancies. Inhibition of FAK using small molecules is a promising therapeutic option for several types of cancer. Here, we conducted computational modeling of FAK targeting inhibitors using 3-dimensional structure-activity relationship (3D-QSAR), molecular dynamics (MD), and hybrid topology-based free energy perturbation (FEP) methods. The structure-activity relationship (SAR) studies between the physicochemical descriptors and inhibitory activities of the chemical compounds were performed with reasonable statistical accuracy using CoMFA and CoMSIA. These are two well-known 3D-QSAR methods based on the principle of supervised machine learning (ML). Essential information regarding residue-specific binding interactions was determined using the MD and MM-PB/GBSA methods. Finally, physics-based relative binding free energy (〖∆∆G〗_RBFE^(A→B)) values of analogous ligands were estimated using the alchemical FEP simulation. An acceptable agreement was observed between the experimental and computed relative binding free energies. The overall results using ML and physics-based hybrid approaches could be useful for the rational optimization of accessible lead compounds with similar scaffolds targeting the FAK receptor.

In this paper, a positive answer to the open question of Fabino et al. is given, and the concept of I\c sik type set valued contractions is introduced and fixed point theorem for such contractions is established. Examples to support main theorems are given, and an application to integral inclusion is given.

This paper uses the complex regression analysis method to establish the customer’s load regression models, which consider economic indicators, temperature and rainfall. Furthermore, the proposed models are used to study the forecasting feasibility of the future energy sales and summer peak load demand. At first, this paper used least-squares techniques to derive regression models for considering economic indicators and temperature of 34 customer energy sales and total energy sales. Besides, the AMI high voltage customer demand data and system generating capacity for 24 hours were adopted to forecast summer peak load. The above-mentioned data analysis tool is used by EViews software to achieve, in order to verify the feasibility of the research framework. The study found that although its forecasting model accuracy is low only when mixed with temperature and high voltage demands. So, when mixed with high voltage demand data and system generating capacity for 24 hours to forecast peak load, the average error is ± 0.87% and in the majority of its energy sales forecasting model of average error is ±3%. This result can provide power company as future reference.

Currently, maritime traffic is increasing with economic growth in several regions worldwide. However, this growth in maritime traffic has led to increased risk of marine accidents. These accidents have a higher probability of occurring in regions where geographical features, such as islands, are present. Further, the positioning of rescue ships in a particular ocean region with a high level of maritime activity is critical for rescue operations. This paper proposes a method for determining an optimal set of locations for stationing rescue ships in an ocean region with numerous accident sites in the Wando islands of South Korea. The computational challenge in this problem is identified as the positioning of numerous islands of varying sizes located in the region. Thus, the proposed method combines a clustering-based optimization method and an image processing approach that incorporates flood filling to calculate the shortest distance between two points in the ocean that detours around the islands. Experimental results indicate that the proposed method reduces the distance from rescue ships and each accident site by 5.0 km compared to the original rescue ship locations. Thus, rescue time is reduced.

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

This study was conducted on elderly over 65 years of age to verify that healing garden activities control stress in the elderly. The experimental group performed garden activities once a week for 12 weeks, 2 hours each, and the control group continued their daily lives. Each group's cumulative stress at the beginning and end, total power (TP), the standard deviation of the normal-to-normal interval (SDNN), and root mean square differences of successive R-R intervals (RMSSD) were measured using a stress index meter, u-bio MACPA. As a result of the analysis, the experimental group had a statistically significant decrease in cumulative stress compared to the control group, and TP significantly increased compared to the control group. SDNN and RMSSD of the experimental group increased, respectively, and the control group decreased, respectively, but it was not statistically significant. The fact that cumulative stress decreased, and stress evaluation indicators increased shows that daily stress can be controlled through healing garden activities. This confirms that the value of the garden can extend to healing.

Few clinical factors can help predict spontaneous culture conversion (SCC) in patients with Mycobacterium avium complex-pulmonary disease (MAC-PD). We retrospectively classified 373 MPD patients who had undergone watchful waiting without antibiotics according to the so-called ‘body mass index (BMI), age, cavity, erythrocyte sedimentation rate (ESR), and sex (BACES)’ severity. We evaluated whether lower severity is associated with a higher rate of SCC. Of 373 patients, 153 (41%) achieved SCC without antibiotics during a median follow-up of 48.1 months. There was a trend toward a higher SCC rate in patients with lower BACES severity: 48% (87/183), 37% (58/157), and 24% (8/33) in the mild, moderate, and severe BACES groups, respectively. In addition, a favorable outcome, defined as maintaining SCC or having two consecutive negative sputum cultures until the last follow-up date, was also more common in patients with lower BACES severity with 53% (97/183), 34% (54/157), and 18% (6/33) in the mild, moderate, and severe BACES groups, respectively. In multivariate analysis, moderate (hazard ratio [HR]=0.63; 95% confidence interval [CI] 0.44 – 0.91; p = 0.013) and severe BACES (HR 0.37; 95% CI 0.16 – 0.90; p = 0.028) had a significantly negative impact on favorable outcomes compared to mild BACES. Lower BACES severity may be associated with SCC in MAC-PD patients.

Penile augmentation using filler injections is a growing trend; however, the foreign body reaction can cause complications such as ulcer and necrosis of the penis, which can requires reconstruction. The existing method of reconstruction of the penis focused on filling the deficit. We report a case involving a scrotal flap and autologous augmentation using a de-epithelialization technique for a soft tissue defect caused by delayed infection after a penile filler injection. The defect was reconstructed and an augmentation effect was achieved. The patient was a 41-year-old man who received an injection of Aquafilling® (Biomedica, Prague, Czech Republic) 7 years previously and developed a delayed infection. After debridement, the penile defect spanned the entire shaft, and the circumference of the penis was 7.5 cm. Using a bilateral scrotal flap technique, the inferior margins of both flaps were rolled inward after de-epithelialization to achieve autologous augmentation. No infection or flap necrosis occurred during the 3-month follow-up period after surgery. Additionally, the penis circumference was expanded to 12 cm, and the patient indicated that he was very satisfied with the result. This surgical technique can be widely applied as treatment for penile defects.

As broiler farming facilities have become larger and more concentrated in response to external environmental changes, there is a possibility of increased concentrations of fine dust and aerosols inside these facilities due to enclosure. In particular, workers are exposed to high concentrations of organic particulate matter and harmful gases while performing their tasks, and as they age, they become more vulnerable to respiratory diseases. It is essential to directly monitor the concen-trations to which workers are exposed, along with the spatial distribution of aerosols inside broiler house. In this study, we analyzed the regional aerosol concentrations using passive samplers in commercial tunnel-ventilated broiler farms. Simultaneously, we employed active samplers at the height of the workers' breathing zones to monitor real-time aerosol concentrations by particle size along their work routes. Spatial aerosol concentrations generally increased from the inlet to the exhaust in the breathing zone. The average aerosol concentrations were TSP -1,042 µg/m³, PM-10 718 µg/m³, and PM-2.5 137 µg/m³. To analyze the workers' exposure environments, we categorized the tasks in the barn into Static work period (SWP) and Moving work period (MWP) based on video analysis. The results showed that during MWP, fine dust concentrations exceeded the standards by up to 214%. Particularly, during MWP, the concentrations were 1.74 times higher for TSP, 1.40 times higher for PM-10, and 1.22 times higher for PM-2.5 compared to SWP. It was observed that during the movement of workers, physical generation of particles around 10 µm, such as feces, feed, and bedding, occurred due to the movement of chicken, which influenced the aerosol concentration.

Many farms utilize closed-type livestock systems to enhance productivity and facilitate effective environmental management. However, the confined nature of these closed spaces poses an increased risk of exposure to harmful gases and organic dust for both workers and livestock. Additionally, the introduction of outside air through ventilation systems can lead to temperature fluctuations within the breeding environment, resulting in potential productivity issues. This research paper employs computational fluid dynamics (CFD) to develop ventilation operation management plans that address both the working environment and the breeding environment simultaneously. The proposed plans are designed to be easily implemented in practical farm settings. The findings of this study, based on simulation analysis, indicate that while ventilation is effective in reducing harmful gases and improving the working environment, its efficiency decreases after the initial 3 minutes of operation. Furthermore, uncontrolled ventilation can cause sudden temperature changes, which may adversely affect the well-being of the livestock. However, when upgraded ventilation structures are implemented, significant improvements in the working environment (an average of 27.3% improvement) can be achieved while maintaining temperature stability for the livestock. These results highlight the importance of referring to the provided ventilation operation management table before commencing work, as it enables workers to improve the working environment while minimizing the potential impact of ventilation on the breeding environment.

To solve the problem that sampling-based Rapidly-exploring Random Tree (RRT) method is difficult to guarantee optimality. This paper proposed the Post Triangular Processing of Midpoint Interpolation method minimized the planning time and shorter path length of the sampling-based algorithm. The proposed Post Triangular Processing of Midpoint Interpolation method makes a closer to the optimal path and somewhat solves the sharp path problem through the interpolation process. The experiments were conducted to verify the performance of the proposed method. Applying the method proposed in this paper to the RRT algorithm increases the efficiency of optimization compared to the planning time.

This study employs the FLACS code to analyze hydrogen leakage, vapor dispersion, and subsequent explosions. Utilizing pseudo-source models, a liquid pool model, and a hybrid model combining both, we investigate dispersion processes for varying leak mass flow rates (0.225 kg/s and 0.73 kg/s) in a large open space. We also evaluate explosion hazards based on overpressure and impulse effects on humans. The computational results, compared with experimental data, demonstrated reasonable hydrogen vapor cloud concentration predictions, especially aligned with the wind direction. For higher mass flow rate of 0.73 kg/s, the pseudo-source model and hybrid model proved appropriate, while the liquid pool model was more suitable for lower mass flow rate of 0.225 kg/s. Regarding explosion analyses using overpressure-impulse diagram, higher mass flow rates leaded to potentially fatal overpressure and impulse effects on humans. However, lower mass flow rates may cause severe eardrum damage at the maximum overpressure point.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Background: Brain-derived neurotrophic factor (BDNF) has attracted increasing attention as a therapeutic agent because of its potentially biological activities, including osteogenesis. However, the molecular mechanisms involved in the osteogenic activity of BDNF have not been fully investigated. This study aimed to investigate the action of BDNF on the osteoblast differentiation in bone marrow stromal cells, and its influence on signaling pathways. Methods: Preosteoblast cells (MC3T3-E1), bone marrow-derived stromal cells (ST2), and a direct 2D co-culture system were treated with BDNF. The effect of BDNF on cell proliferation was determined using the CCK-8 assay. Osteoblast differentiation was assessed based on alkaline phosphatase (ALP) activity and staining and the protein expression of multiple osteoblast markers. Calcium accumulation was examined by Alizarin red S staining. Results: BDNF significantly increased ALP activity, calcium deposition, and the expression of osteoblast differentiation-related proteins, such as ALP, osteopontin, etc. in both ST-2 and the MC3T3-E1 and ST-2 co-culture system. Moreover, the effect of BDNF on osteogenic differentiation was diminished by blocking tropomyosin receptor kinase B as well as inhibiting c-Jun N-terminal kinase and p38 MAPK signals. Conclusion: Our study results showed positive effect of BDNF on osteogenesis. It provides essential evidence for clinical applications of BDNF in treating osteoporosis.

This study aimed to investigate the effects of lupin flake supplementation on the growth, plasma parameters, carcass characteristics, and meat composition of late-fattening Hanwoo steers. The steers (n = 40) were randomly divided into the four groups with 10 steers each: LP0 (Lupin flake 0%), LP3 (lupin flake 3%), LP6 (Lupin flake 6%), and LP9 (lupin flake 9%). The total digestible nutriant intake increased as the concentration of lupin increased (linear and quadratic effects; P &lt; 0.05). The thiobarbituric acid-reactive substance content in the strip loins decreased as lupin flake supplementation levels increased (linear and quadratic effects; P &lt; 0.05), while carnosine levels increased linearly (P &lt; 0.05). As the lupin flake supplementation level increased, anserine and creatinine contents increased linearly and quadratically (P &lt; 0.05). Similarly, adenosine triphosphate (ATP) and adenosine monophosphate (AMP) contents increased with increasing lupin flake supplementation levels in linear and quadratic effects (P &lt; 0.001). Palmitoleic acid content increased significantly with increasing lupin flake supplementation level (linear and quadratic effects; P &lt; 0.05). The content of oleic acid in the strip loin was not significant, but the unsaturated fatty acid (UFA) (P &lt; 0.05) and n-6/n-3 ratio (P &lt; 0.05) increased. The results of this study indicated that although lupin flake supplementation did not markedly affect the growth, carcass characteristics, or meat composition of late-fattening Hanwoo steers, it exerted a positive effect on the flavor, taste profiles (anserine, creatinine, ATP, and AMP), hypotonicity(TBARS), and healthy meat production (UFA and n-6/n-3 ratio) related to beef.

This paper describes the first results of an Image Recognition Based Location (IRBL) for mobile application focusing on the procedure to generate a Database of range images (RGB-D). In an indoor environment, to estimate the camera position and orientation, a prior spatial knowledge of the surrounding is needed. In order to achieve this objective a complete 3D survey of two different environment (Bangbae metro station of Seoul and E.T.R.I. building in Daejeon – Republic of Korea) was performed using LiDAR (Light Detection And Ranging) instrument and the obtained scans were processed in order to obtain a spatial model of the environments. From this, two databases of reference images were generated using a specific software realized by the Geomatics group of Politecnico di Torino (ScanToRGBDImage). This tool allow to generate synthetically different RGB-D images) centered in the each scan position in the environment. Later, the external parameters (X, Y, Z, ω, φ, κ) and the range information extracted from the DB images retrieved, are used as reference information for pose estimation of a set of acquired mobile pictures in the IRBL procedure. In this paper the survey operations, the approach for generating the RGB-D images and the IRB strategy are reported. Finally the analysis of the results and the validation test are described.

Mechanical properties of cardiomyocytes from different transmural regions are heterogeneous in the left ventricular wall. The cardiomyocyte mechanical environment affects this heterogeneity because of mechano-electric feedback mechanisms. In the present study, we investigated the effects of load upon transmural differences in contraction of subendocardial (ENDO) and subepicardial (EPI) single cells isolated from the murine left ventricle. Various loads were applied to the cells using carbon fiber techniques for single myocytes. To simulate experimentally obtained results and to predict mechanisms underlying the cellular response to change in load, our mathematical models of the ENDO and EPI cells were used. Extent of the transmural gradient in the time course of contractions was independent of the loading conditions where unloaded and heavy loaded (isometric) contractions were examined, but the regional gradient of the relaxation time characteristics tended to decrease when the load decreased. Under auxotonic contractions, time to peak contraction (T_max) was significantly longer in ENDO cells than in EPI cells at low preload. An increase in preload (axial stretch) prolonged T_max in both cell types; however, the prolongation was greater in EPI cells, resulting in a decrease in transmural gradient in T_max at high preload. The [Ca²⁺]_i transient decay time constant was consistent with the greater preload dependency in T_max of EPI cells. Our modified mathematical models reproduced experimental results, suggesting that differences in cooperativity of cross bridges and calcium troponin C complex interactions between the ENDO and EPI cardiomyocytes may contribute to the different cellular responses to stretch, which may provide a decrease in transmural dispersion of cellular shortening in the intact heart.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

Mutations in the SACS gene are associated with autosomal recessive spastic ataxia of Charlevoix-Saguenay disease (ARSACS) or complex clinical phenotypes of Charcot-Marie-Tooth disease (CMT). This study aimed to identify SACS mutations in a Korean CMT cohort with cerebellar ataxia and spasticity. As a result, eight pathogenic SACS mutations in four families were identified as the underlying causes of these complex phenotypes. The prevalence of CMT families with SACS mutations was determined to be 0.3%. All the patients showed sensory, motor, and gait disturbances with increased deep tendon reflexes. Lower limb magnetic resonance imaging (MRI) was done in four patients, and all had fatty replacements. Of note, they all had similar fatty infiltrations between the proximal and distal lower limb muscles, different from the neuromuscular imaging feature in most CMT patients without SACS mutations who had distal dominant fatty involvement. Therefore, these findings were considered a characteristic feature in CMT patients with SACS mutations. Although further studies with more cases are needed, our results highlight lower extremity MRI findings in CMT patients with SACS mutations and broaden the clinical spectrum. We suggest screening for SACS in recessive CMT patients with complex phenotypes of ataxia and spasticity.

This paper addresses a method to transmit streaming data via rolling shutter camera-based optical camera communications (OCC). Since the amount of data that can be contained within one frame is limited, and the continuity of received data cannot be guaranteed due to OCC environmental variations, we introduce the concept of dividing the streaming data into several fragmented sets that are transmitted sequentially. We propose a superframe to contain sequential packets of fragmented data and corresponding indexes, so that sequential packets for streaming data can be continuously collected. When redundant frame transmission is considered, any packet lost due to OCC environmental conditions can be recovered. Experimental results show that the proposed method can be successfully used to transmit streaming data, with the number of redundant frames required to acquire all data packets based on image resolution. In addition, we describe how to identify missing packets from a network point of view to reduce the number of redundant frames needed to acquire all the data. This paper presents baseline results of communication performance when sending streaming data via a rolling shutter-based OCC.

Background: Probiotics can provide health benefits to an individual by regulation of the immune system. Many clinical trials have found that probiotics can prevent upper respiratory tracts infections. Aim: To perform a systematic review and meta-analysis of available trials to investigate the effectiveness of probiotics in the prevention of upper respiratory tract infections in individuals of all ages. Conclusion: Probiotics were found to be better in reducing the number of participants who experienced acute URTI, the average duration per episode of acute URTI, use of antibiotics in URTI related cases and absence due to URTI. Side effects were found to be minor, making probiotics a good candidate for clinical use. This shows that probiotics are effective in preventing acute URTIs. However, due to limited studies and small sample size, the results are subjected to bias and should be interpreted with care.

Fluorescent bioprobes are invaluable tools for visualizing live cells and deciphering complex biological processes by targeting intracellular biomarkers without disrupting cellular functions. In addition to protein-binding concepts, fluorescent probes utilize various mechanisms, including membrane, metabolism, and gating-oriented strategies. This study introduces a novel fluorescent mechanism distinct from existing ways. Here, we developed a B-cell selective probe, CDrB, with unique transport mechanisms. Through SLC-CRISPRa screening, we identified two transporters, SLCO1B3 and SLC25A41, by sorting out populations exhibiting higher and lower fluorescence intensities, respectively, demonstrating contrasting activities. We confirmed that SLCO1B3, with comparable expression levels in T and B cells, facilitates the transport of CDrB into cells, while SLC25A41, overexpressed in T lymphocytes, actively exports CDrB. The observation suggests that SLC25A41 plays a crucial role in discriminating between T and B lymphocytes. Furthermore, it reveals the potential for reversible localization of SLC25A41 to demonstrate its distinct activity. This study is the first report to unveil a novel strategy of SLC by exporting the probe. We anticipate that this research will open up new avenues for developing fluorescent probes.

How perceptual limits can be overcome has long been examined by psychologists. This study investigated whether visual cues, blindfolding, visual-auditory synesthetic experience and music training could facilitate a smaller frequency difference limen (FDL) in a gliding frequency discrimination test. It was hoped that the auditory limits could be overcome through visual facilitation, visual deprivation, involuntary cross-modal sensory experience or music practice. Ninety university students, with no visual or auditory impairment, were recruited for this one-between (blindfold/visual cue) and one-within (control/experimental session) designed study. A MATLAB program was prepared to test their FDL by an alternative forced-choice task (gliding upwards/gliding downwards/no change) and two questionnaires (Vividness of Mental Imagery Questionnaire & Projector-Associator Test) were used to assess their tendency to synesthesia. Participants with music training showed a significantly smaller FDL; on the other hand, being blindfolded, being provided with visual cues or having synesthetic experience before could not significantly reduce the FDL. However, the result showed a trend of reduced FDLs through blindfolding. This indicated that visual deprivation might slightly expand the limits in auditory perception. Overall, current study suggests that the inter-sensory perception can be enhanced through training but not though reallocating cognitive resources to certain modalities. Future studies are recommended to verify the effects of music practice on other perceptual limits.

We evaluated the association of blood pressure with blood levels of cadmium, lead, and cadmium and lead together (cadmium+lead) in a representative sample of adolescents from Korea by use of 2010-2016 data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study enrolled adolescents aged at 10-18 years-old who completed a health examination survey and had blood measurements of lead and cadmium. The association of adjusted mean differences in diastolic and systolic blood pressure with doubling of blood lead and cadmium were estimated by regression of blood pressure against log₂-transformed blood metals and their quartiles after covariate adjustment. Adjusted odds ratios for prehypertension were calculated for log₂-transformed blood levels of lead and cadmium and their quartiles. Our analysis of adolescents in Korea indicated that blood levels of lead and cadmium were not significantly associated with increased blood pressure or risk of pre-hypertension. However, the cadmium+lead level was associated with pre-hypertension. Previous studies showed that blood levels of lead and cadmium were associated with increased blood pressure and risk of hypertension in adult populations. We found no such effect in Korean adolescents, although the cadmium+lead level was associated with prehypertension. These differences may be because adolescents generally have lower levels of these blood metals or because adolescents only rarely have hypertension.

Anxiety disorders affect patient quality of life (QoL). This study aimed to examine the associations between improved QoL and reduced clinical symptoms and Korean medicine (KM) in patients with anxiety disorders. Medical records of patients with anxiety who were treated with KM (acupuncture, Anxiety disorders affect patient quality of life (QoL). This study aimed to examine the associations between improved QoL and reduced clinical symptoms and Korean medicine (KM) in patients with anxiety disorders. Medical records of patients with anxiety who were treated with KM (ac-upuncture, psychotherapy, Chuna therapy, aromatherapy, or herbal medicine) for at least 4 weeks were retrospectively analyzed. Clinical, QoL, and cost outcomes were measured at baseline and at 4 and 12 weeks (Anxiety: State-Trait Anxiety Inventory[STAI X-1(state), X-2(trait)], Beck Anxiety Inventory[BAI]; anger: State-Trait Anger Expression Inventory State[STAXI-S(state), T(trait)], Anger Expression Inventory[AXI-K-I(anger-in), AXI-K-O(anger-out), AXI-K-C(anger-control); depression: Beck Depression Inventory-II[BDI II], QoL: QoL-related instruments Euro Quality of Life 5 Dimensions utility score[EQ-5D], Euro QoL Visual Analog Scale[EQ-VAS]). The quali-ty-adjusted life years (QALYs) and average cost-effectiveness ratio of KM for anxiety were esti-mated. The medical records for 67 patients were evaluated. KM treatments were found to be as-sociated with decreased anxiety (STAI X-1; STAI X-2; BAI, p

Background: Autonomic neuropathy commonly arises as a long-term complication in end stage kidney disease (ESKD) and can be diagnosed from heart rate variability (HRV), calculated from electrocardiogram (ECG) recordings. There is limited data about HRV using real-time ECG to predict HD efficiency in patients with ESKD who are routinely doing HD in real-world practice. Methods: Total of 50 patients (62.1 ± 10.7 years) with ESKD underwent continuous real-time ECG monitor (237.4 ± 15.3 min) during HD for HRV using remote monitoring system and checked electrolyte levels before/after HD. And we compared HRV according to electrolyte levels. Results: During the monitor, we checked total 2374 times of ECG and electrolyte level simultaneously of all patients. Both time and frequency domain HRV were higher when the patients had lower K+ level (&lt;0.5 mEq/L) and P+ level change (&lt;2 mEq/L) before/after HD as compared with those with higher K+ level (≥0.5 mEq/L) and P+ level (≥2 mEq/L) change respectively. In addition, there were higher incidence of arrhythmic events including atrial/ventricular premature complexes, even though no difference of mean heart rate in patients with lower K+ and P+ level change group (p &lt; 0.001). Conclusions: Higher HRV was independently associated with poor controlled K+ and P+ level during hemodialysis in patients with ESKD. This is further substantiated by independent continuous associations between real-time measures of higher HRV and K+ and P+ level. These data strongly suggest that cardiac autonomic dysfunction can be caused by lower change of electrolytes before/after hemodialysis alone.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

. Various elements such as evolutions in IoT services resulting from sensoring by vehicle parts and advances in small communication technology devices have significantly impacted the mass spread of mobility services that are provided to users in need of limited resources. In particular, business models are progressing away from one-off cost towards longer term cost as represented by shared services utilizing kick-boards or bicycles and subscription services for vehicle software. Advances in shared mobility services as described are calling for solutions that can enhance reliability of data aggregate by users leveraging mobility services in the next-generation mobility areas. However, mining process to renew status, ensures continued network communication and block creation demands high performance in public block chain. This thesis proposes random certificate node selection mechanism in block network that creates blocks via node that has tokens issued for block creation and lets only specific nodes selected by encrypting token information acquires token.

The fundamental objective is to study the application of multivariate sets of data in Gaussian distribution. This paper examines broad measurements of structure for both Gaussian and non-Gaussian distributions, which shows that they can be described in terms of the infor-mation-theoretic between the given covariance matrix and correlated random variables (in terms of relative entropy). In order to develop the multivariate Gaussian distribution with entropy and mutual information, several significant methodologies are presented through the discussion supported by illustrations, both technically and statistically. The content obtained allows readers to better perceive concepts, comprehend techniques, and properly execute software programs for future study on the topic's science and implementations. It also helps readers grasp the themes' fundamental concepts. Involving the relative entropy and mutual information as well as the potential correlated covariance analysis based on differential equations, a wide range of information is addressed, including basic to application concerns.

Patients with cancer experience insomnia or sleep disturbances. This study aimed to explore whether the discrepancy between a patient's desired time in bed and total sleep time (DBST) index is a measurement tool for insomnia severity or sleep onset latency [SOL] in patients with cancer. This retrospective medical records review study gathered clinical information and rating scale scores including Insomnia Severity Scale (ISI), Cancer-related Dysfunctional Beliefs about Sleep scale (C-DBS), Patient Health Questionnaire-9 items (PHQ-9), State subcategory of State and Trait Anxiety Inventory, and Short form of Fear of Progression Questionnaire. Sleep indices of time variables (bedtime, sleep onset time, and wake-up time), duration variables [SOL, time in bed (TIB), time in bed for 24 hours (TIB/d), and duration from wake-up time to bedtime (WTB)], and the DBST index were calculated. The ISI score was predicted by PHQ-9 (β=0.34, P&lt;0.001), C-DBS (β=0.17, P=0.034), and DBST index (β=0.22, P=0.004) with a significant correlation with the DBST index (r=0.19, p=0.020). The DBST index was significantly correlated with long SOL (r=0.23, P=0.005). Long SOL was predicted by early bedtime (β=0.18, P=0.045), short WTB (β=-0.26, P=0.004), and high DBST index (β=0.19, P=0.013). The DBST index was significantly correlated with a predicting variable each for insomnia severity and SOL in patients with cancer.

Cardiac hypertrophy is an adaptive response to various pathological insults including hypertension. However, sustained hypertrophy can cause impaired calcium regulation, cardiac dysfunction, and remodeling, accompanied by cardiac fibrosis. Our previous study identified miR-25 as a regulator of SERCA2a, and that inhibition of miR-25 improved cardiac function and reduced fibrosis by restoring SERCA2a expression in a murine heart failure model. However, the precise mechanism underlying the reduction of fibrosis by miR-25 inhibition remains unclear. Therefore, we postulate that miR-25 may have additional targets that contribute to regulating cardiac fibrosis. Using in silico analysis, Krüppel-like factor 4 (KLF4) was identified as an additional target of miR-25. Further experiments confirmed that KLF4 was directly targeted by miR-25 and that its expression was reduced by long-term treatment with Angiotensin II, a major hypertrophic inducer. Subsequently, treatment with a miR-25 inhibitor alleviated the cardiac dysfunction, fibrosis, and inflammation induced by Angiotensin II. These findings indicate that inhibiting miR-25 not only enhances calcium cycling and cardiac function via SERCA2a restoration but also reduces fibrosis by restoring KLF4 expression. Therefore, targeting miR-25 may be a promising therapeutic strategy for treating hypertensive heart diseases.

ABSTRACT Background Ubiquitination plays an important role in protein post-translational processes and has been found to be involved in a number of regulatory functions including proteasome degradation, DNA repair, transcription, signal transduction, endocytosis, and sorting. As the identification of ubiquitination site is critical to furthering our understanding of the mechanism of ubiquitination, various experimental and machine learning methods have been used to conduct this task. It has been an important but challenging task to improve the accuracy of ubiquitination site prediction. In this research, we explore the possibility of improving the prediction performance of machine learning by incorporating grid search in the training process. Method We developed grid search procedures for each of six widely used machine learning methods including NB, LR, DT, SVM, LASSO, and KNN, and applied them to ubiquitination site prediction using the six PCP datasets that were previously developed. For each of the ML methods, we developed a set of values for each of the tunable hyperparameters available to the method. These sets of values then can be combined to form a large grid of hyperparameter settings, and each of these settings is used in the grid search. We integrated 5-fold cross-validation in grid search to train and test ML models and applied an additional independent validation procedure by conducting a pre-training 80-20 sample split. We evaluated the performance of the six methods by comparing them side by side for each of the six datasets. We also compared the grid search results with the results that were previously published without doing grid search. To optimize the prediction performance, we trained 1.1 million ML models in total through grid search. Results We compared the overall prediction performance of these six methods, as well as their prediction performance when working with balanced vs. imbalanced data, and large-scale vs. small-scale data. From the perspective of dataset, we find that the overall performance of every PCP dataset has been significantly improved in this study compared to the previous study, with the percentage increase of the average AUC of all six datasets ranging from 7.9% (PCP-4) up to 17.0% (PCP-1). From the perspective of method, we find that three out of four methods significantly benefit from grid search comparing to their previously published non-grid search results, with the maximum AUC improvement as high as 47% (LASSO on PCP-5), 43.3% (NB on PCP-1), and 33.7% (SVM on PCP-6). SVM overall ranks number one, followed by KNN as the number two performer based on their average AUCs on all datasets. But these two also ranked the top two (KNN 76 days and SVM 15 days) in terms of the total running time that they need to do grid search. We also find that SVM, KNN, and DT tend to handle small-scale and imbalanced datasets better, while LR, and LASSO are doing well with large-scale and balanced datasets. NB is more sensitive to data imbalance while less sensitive to the size of a dataset. Conclusions Our results show that using grid search has improved the performance of ubiquitination prediction significantly. We find that the performance of a method is closely related to its hyperparameter setting and the type of data it handles. Even though SVM is on average an outperformer, none of the methods can provide the best performance for all datasets. When sufficient computing resources are well accessible, grid search is an effective way to identify both a top performing model for a machine learning method and a suitable machine learning method for a particular dataset.

In the information age today, data are getting more and more important. While other industries achieve tangible improvement by applying cutting edge information technology, the construction industry is still far from being enough. Cost, schedule, and performance control are three major functions in the project execution phase. Along with their individual importance, cost-schedule integration has been a significant challenge over the past five decades in the construction industry. Although a lot of efforts have been put into this development, there is no method used in construction practice. The purpose of this study is to propose a new method to integrate cost and schedule data using big data technology. The proposed algorithm is designed to provide data integrity and flexibility in the integration process, considerable time reduction on building and changing database, and practical use in a construction site. It is expected that the proposed method can transform the current way that field engineers regard information management as one of the troublesome tasks in a data-friendly way.

A heat pump with thermal storage system is a system that operates a heat pump during night-time using inexpensive electricity; during this time, the generated thermal energy is stored in a thermal storage tank. The stored thermal energy is used by the heat pump during daytime. Based on a model of a dual latent heat storage tank and a heat pump, this study conducts control simulations using both conventional and advanced methods for heating in a building. Conventional methods include the thermal storage priority method and the heat pump priority method, while advanced approaches include the region control method and the dynamic programming method. The heating load required for an office building is identified using TRNSYS, used for simulations of various control methods. The thermal storage priority method shows a low coefficient of performance (COP), while the heat pump priority method leads to high electricity costs due to the low use of thermal storage. In contrast, electricity costs are lower for the region control method, which operates using the optimal part load ratio of the heat pump, and for dynamic programming, which operates the system by following the minimum cost path. According to simulation results for the winter season, the electricity costs using the dynamic programming method are 17% and 9% lower than those of the heat pump priority and thermal storage priority methods, respectively. The region control method shows results similar to the dynamic programming method with respect to electricity costs. In conclusion, advanced control methods are proven to have advantages over conventional methods in terms of power consumption and electricity costs.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

Major depressive disorder (MDD) is one of the most prevalent and disabling mental disorders worldwide. Among the symptoms of MDD, sleep disturbance such as insomnia is prominent and the first reason patients may seek professional help. However, the underlying pathophysiology of this comorbidity is still elusive. Recently, genome-wide association studies (GWAS) have begun to unveil the genetic background of several psychiatric disorders, including MDD and insomnia. Identifying the shared genomic risk loci between comorbid psychiatric disorders could be a valuable strategy to understand their comorbidity. This study seeks to identify the shared genes and biological pathways between MDD and insomnia based on their shared genetic variants. First, we performed a meta-analysis based on the GWAS summary statistics of MDD and insomnia obtained from Psychiatric Genomics Consortium and UK Biobank, respectively. Next, we associated shared genetic variants to genes using two gene mapping strategies: (a) positional mapping based on genomic proximity and (b) expression quantitative trait loci (eQTL) mapping based on gene expression linkage across multiple tissues. As a result, a total of 719 shared genes were identified. Over half (51%) of them are protein-coding genes. Functional enrichment analysis shows that the most enriched biological pathways are related to epigenetic modification, sensory perception, and immunologic signatures. We also identified druggable targets using a network approach. Together these results may provide insights into understanding the genetic predisposition and underlying biological pathways of comorbid MDD and insomnia symptoms.

Emotion detection holds significant importance in facilitating human-computer interaction, enhancing the depth of engagement. By integrating this capability, we pave the way for forthcoming AI technologies to possess a blend of cognitive and emotional understanding, bridging the divide between machine functionality and human emotional complexity. This progress has the potential to reshape how machines perceive and respond to human emotions, ushering in an era of empathetic and intuitive artificial systems. This paper introduces a novel approach to multimodal emotion recognition, seamlessly integrating speech and text modalities to accurately infer emotional states. Employing CNNs, we meticulously analyze speech using Mel spectrograms, while a BERT-based model processes the textual component, leveraging its bidirectional layers for profound semantic comprehension. The outputs from both modalities are combined using an attention-based fusion mechanism that optimally weighs their contributions. The proposed method undergoes meticulous testing on two distinct datasets: Carnegie Mellon University’s Multimodal Opinion Sentiment and Emotion Intensity (CMU-MOSEI) dataset and the Multimodal Emotion Lines Dataset (MELD). The results demonstrate superior efficacy compared to existing frameworks, achieving an accuracy of 88.4% and an F1-score of 87.9% on the CMU-MOSEI dataset, and a notable weighted accuracy (WA) of 67.81% and a weighted F1 (WF1) score of 66.32% on the MELD dataset. This comprehensive system offers precise emotion detection and introduces several significant advancements in the field.

This study aims to understand the changes in management trends among global companies before and after the onset of COVID-19. To achieve this, we employed keyword and topic modeling to analyze 420 CEO messages extracted from the reports of the Fortune Global 100 largest companies. The analysis revealed a noteworthy prevalence of keywords associated with shared culture, such as face-to-face interactions and cooperation, during the initial period. In the subsequent period, we observed a higher frequency of keywords related to community-centeredness and digital trans-formation, including employee health and well-being, inequality reduction, and sustainable cities. Furthermore, we identified common topics before and after COVID-19, such as risk management and competitive advantage. However, the topics that exhibited variation were the significance of corporate leadership and the evolution of digital technologies. This study is significant in that it enables us to analyze CEO messages and deduce the trajectory of corporate management post-COVID-19.

In this study, the focus is on the drop test simulation of an MR (Magnetorheological) damper-based main landing gear (MRMLG), aiming to explore multi-degree-of-freedom (DOF) dynamic models during aircraft landing. Three different 6-DOF dynamic models are proposed in this work and their drop performances are compared with results achieved one of commercial softwares. The proposed models include a nonlinear aircraft model (NLAM), a linearized approximated aircraft model (LAAM) linearizing from the nonlinear equations of motion in NLAM, and a fully approximated aircraft model (FAAM) which linearizes the MRMLG's strut force model. In order to evaluate drop performance of the aircraft landing gear system with MR dampers, a 7-DOF aircraft model incorporating the nonlinear MRMLG is formulated using RecurDyn. The principal comparative param-eters are the coefficient of determination (R2) for system response of each model with Re-curDyn model and root mean square error (RMSE) which is the ensembles of CG dis-placement data for each model. In addition, the ensemble of time series data is created for diverse drop scenarios, providing valuable insights into the performance of the proposed drop test models of the aircraft landing gear system featuring MR dampers.

This study proposed to use wearable EEG to study the impact of vipassana mindfulness practice on beginner's physiological and neurological responses. Mindfulness meditation has been shown to have numerous benefits, including stress reduction, improved attention and cognitive function, and enhanced emotional regulation. The roots of mindfulness meditation in Buddhism emphasize cultivating present-moment awareness and insight. However, the neural mechanisms together with physiological mechanism and their interaction underlying these benefits remain poorly understood. Method: One middle age man (50 years old) participated in this longitudinal study using wearable EEG to investigate the neurophysiological change during a one-month consecutive vipassana mindfulness practice. Both EEG and heart rate responses were recorded each time, before (5 minutes), during (20 minutes), and after (5 minutes) meditation sessions. The EEG and HR data were analyzed by Matlab and EEGlab to examine changes in brainwave activity and heart rate. Results: alpha peak frequency (APF) is significantly lower after mindfulness meditation, as shown by comparison of APF before mindfulness (pre-5) and during mindfulness practice (med-20), and comparison between APF of pre-5 and after mindfulness practice (post-5). The same is with the beta peak power. While for theta peak frequency, it is significant lower during mindfulness meditation (med-20), when comparing to either pre-5 or post-5. See figure 1a. However, peak power index is not so sensitive, and it is more obvious in theta wave band. That is, the theta power peak is significantly lower after meditation, as can be observed in comparison between pre-5 and med-20, also between pre-5 and med-20. See figure 1b. STATE Heart-mean (bpm) Heart-std(bmp) pre-5 69.88 3.88 med-20 68.36 2.81 post-5 69.55 4.13 t-value test (pre-med) 0.0694 0.0003 t-value test (pre-post) 0.7934 0.3656 t-value test (post-med) 0.3193 0.0001 Table 1. The difference of Heart rate (mean and SD) in before (pre-5), during (med-20) and after (post-5)mindfulness meditation. We find significant change in standard deviation (SD) of heart rate between meditation and non-meditation mental states, as shown in table 1. The study provides insights into the underlying neurophysiological mechanisms of mindfulness meditation using wearable EEG devices. It demonstrates that in term of EEG measurement, spectrum frequency can be more sensitive than spectrum power; also heart rate variability as measured by SD is more sensitive to mean of HR. The proposed study contributes to the literature by using wearable EEG devices to collect data in a more accessible and convenient manner.

As the digital transformation accelerates in our society, open data is being increasingly recognized as a key resource for digital innovation in the public sector. This study explores the following two research questions: 1) Can a machine learning approach be appropriately used for measuring and evaluating open data utilization? 2) Should different machine learning models be applied for measuring open data utilization depending on open data attributes (field and usage type)? This study used single-model (Random Forest, XGBoost, LightGBM, CatBoost) and multi-model (Stacking Ensemble) machine learning methods. A key finding is that the best-performing models differed depending on open data attributes (field and type of use). The applicability of the machine learning approach for measuring and evaluating open data utilization in advance was also confirmed. This study contributes to open data utilization and to the application of its intrinsic value to society.