This study presents the design and implementation of a PLC microprocessor adhering to the IEC-61131-3 standard, executed on a Cyclone-V FPGA using a DE10-NANO development board. Our microprocessor optimizes the central processing unit by streamlining the data path, achieving a remarkable simulated response time of approximately 60 ns, equivalent to three clock cycles at a 50MHz frequency for Boolean operations. To substantiate our approach, we conducted practical experiments utilizing a FESTO conveyor station, employing relays as actuators, and incorporating optical and inductive sensors. The results underscore the feasibility of our proposed approach and serve as practical validation of its efficacy. This work introduces a promising avenue for the development of cost-effective PLCs employing SoC FPGA variants. Additionally, a thorough comparison of execution times with other early reported architectures. Our microprocessor outperforms even well-established PLCs like the S7-312, with substantial reductions in execution times of 94.54% for floating-point operations, 71.42% to 93.33% for word operations, and up to 78.57% for bit operations.

Olive tree vegetal materials are considered a powerful source for isolation of bioactive compounds, mainly, phenols and triterpenic acids. However, the high humidity content of them reduces their preservation and extractability to a liquid solvent. Accordingly, a drying step is crucial to homogenize the material and to obtain an efficiency extraction. We studied the influence of the drying process on the extraction efficiency of bioactive compounds from olive vegetal material. For this purpose, we evaluated the effects of four drying processes on the solid–liquid extraction of bioactive compounds from two by-products, olive leaves and pomace, and olive fruits harvested from two cultivars, Alfafara and Koroneiki. Infrared-assisted drying (IAD) was the most suited approach to obtain extracts enriched in oleuropein from leaves. In the case of pomace, lyophilization and microwaves-assisted drying led to extracts concentrated in oleacein and oleuropein aglycone, whereas IAD and oven-drying led to extracts with enhanced content in hydroxytyrosol glucoside and hydroxytyrosol, respectively. The drying process affected considerably to the chemical composition of extracts obtained from fruits. Changes in the composition of extracts were explained essentially by the drying process conditions using auxiliary energies, temperature and time, which promoted chemical alterations and increased the extractability of compounds.

Obesity is a risk factor for the development of gestational diabetes mellitus (GDM). However, the most optimal type of nutritional intervention to prevent GDM in high-risk women is not clearly defined. This study investigates if nutritional treatment based on the Mediterranean diet (MedDiet) before 12th gestational week (GW) in women at high risk due to a body mass index (BMI)≥25kg/m2, reduces the rate of GDM and metabolic syndrome (MetS) at 3 years postpartum. We performed a post-hoc analysis of the San Carlos Gestational Prevention Study. A total of 735 women with BMI≥25kg/m2 were evaluated between 2015-2018, 246 in standard diet control group (CG) and 489 in MedDiet intervention group (IG). The rate of GDM was significantly lower in IG compared to CG (25.1%vs31.7%;p=0.037). Postnatal follow-up was completed by 141 women in CG (57%) and 312 women in IG (64%). At 3 years postpartum, we observed a reduction (relative risk 95% confidence interval) in the rates of impaired fasting glucose (IFG) (0.51 (0.28-0.92);p=0.019), obesity (0.51 (0.28-0.92),p=0.041), waist circumference (WC)≥89.5cm (0.54 (0.31-0.94);p=0.022) and MetS (0.56 (0.33-0.94);p=0.003). MedDiet reduces the rate of GDM and postpartum MetS in women with BMI)≥25kg/m2, suggesting that its implementation should be routinely recommended from the first GWs.

An aneurysm is a vascular malformation, it can be classified according to its location (cerebral, aortic); and according its shape (saccular, fusiform, and mycotic). The study of blood flow interaction with the aneurysms has gained attention from physicists an engineers in recent years. Shear stresses, oscillatory shear index (OSI), gradient oscillatory number (GON), and residence time had been used as potential variables to describe the hemodynamics as well as the origin and evolution of aneurysm. However, the causes of aneurysms and the hemodynamics conditions that promote the growth of these structures are still under debate. The present work presents numerical simulation on three aneurysms: 2 aortic and 1 cerebral. The results shows that the blood rheology is not relevant for aortic aneurysms, however, for cerebral aneurysm could play a relevant role in the hemodynamics. The turbulence models evaluated show equivalent results in both cases. Lastly, a simulation considering the fluid-structure interaction (FSI) shows that this phenomenon is the dominant factor for aneurysms simulation.

We present a model of space that considers it to be a quantized dynamical entity which is a component of the universe along with matter and radiation. The theory is used together with thermodynamic data to provide a new view of cosmic evolution and an insight into the nature of dark energy and dark matter. Space is made up of energy quanta. The universe started from an atomic size volume at very high temperature and pressure near the Planck epoch. Upon expansion and cooling, phase transitions occurred resulting in the formation of radiation, fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters. From a phase diagram of cosmic composition, we obtained a correlation between dark energy and the energy of space. Using the Friedmann equations, data from WMAP studies of the composition of the universe at 3.0 x 10⁵ (a=5.25 x 10^-2) years and at present (a=1), are well fitted by our model with an equation of state parameter, w= -0.7. The accelerated expansion of the universe, starting at about 7 billion years, determined by BOSS measurements, also correlates well with the dominance of dark energy at 7.25 x 10⁹ years ( a= 0.65). The expansion can be attributed to Quintessence with a space force arising from a quantum space field. From our phase diagram, we also find a correlation suggesting that dark matter is a plasma form of matter similar to that which existed during the photon epoch immediately prior to recombination. Our Quantum Space Model leads to a universe which is homogeneous and isotropic without the need for inflation. The thermodynamics of expansion is consistent with BOSS data that show the process to be adiabatic and the rate of expansion decelerating during the first 6 billion years after the Big Bang. However, it became non-adiabatic and accelerating thereafter. This implies an influx of energy from a source outside the universe; it warrants consideration as a possible factor in the accelerated expansion of the universe.

The production and N-glycosylation of recombinant human butyrylcholinesterase (BChE), a model highly glycosylated therapeutic protein, in a transgenic rice cell suspension culture treated with kifunensine, a strong α-mannosidase I inhibitor, was studied in a 5 L bioreactor. A media exchange was performed at day 7 of cultivation by removing spent sugar rich media (NB+S) and adding fresh sugar free (NB-S) media to induce the rice α-amylase 3D (RAmy3D) promoter to produce rice recombinant human BChE (rrBChE). Using a 1.25X concentrated sugar-free medium together with an 80% reduced working volume during the media exchange lead to a total active rrBChE production level of 79 ± 2 µg (g FW)^-1 or 7.5 ± 0.4 mg L^-1 in the presence of kifunensine, which is 1.5-times higher than our previous bioreactor runs using normal sugar free medium with no kifunensine treatment. Importantly, the amount of secreted active rrBChE in culture medium was enhanced in the presence of kifunensine, comprising 44% of the total active rrBChE at day 5 post-induction. Coomassie stained SDS-PAGE gel and Western blot analyses reveal different electrophoretic migration of purified rrBChE bands with and without kifunensine treatment, which is attributed to different N-glycoforms. N-Glycosylation analysis shows substantial increase of oligomannose glycans (Man5/6/7/8) in rrBChE treated with kifunensine compared to controls. However, mass transfer limitation of kifunensine is likely the major reason for incomplete inhibition of α-mannosidase I in this bioreactor study.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

We present a Quantum Space Model (QSM) of the evolution of the universe based on the theory that space consists of energy quanta from which it began. We used the Friedmann equations to trace its history and show that Dark Energy is the energy of space which caused its accelerating expansion.The universe started from a quanta of space which was triggered by quantum fluctuations that caused the Big Bang. It then expanded and cooled undergoing phase transitions to radiation, fundamental particles, and matter. Matter grew into galaxies, and was consolidated by gravity into Black Holes, ending in a Big Crunch and Deep Freeze inside a Black hole at 1.380 trillion years. Fluctuations caused a new Bang to start another cycle in its life. If the Law of Conservation of Energy is universal, then the cosmos is eternal. Our results support the theoretical predictions of a cyclic universe by Steinhardt and associates, as well as Penrose. Space and energy are equivalent as embodied in the Planck energy equation. They are the two most fundamental quantities that govern cosmic evolution. The two principal long range forces are the gravitational force and the space force,which maybe the fifth force in the universe. They provide the clockwork mechanism operating our cyclic universe.

Reactive oxygen species (ROS) are intermediates in oxidation-reduction reactions with the capacity to modify biomolecules and temporarily or permanently alter cell behaviour through signalling pathways under physiological and pathophysiological conditions where there is an imbalance between oxidative factors and the antioxidant response of the organism, a phenomenon known as oxidative stress. Evidence suggests that differential modulation of ROS-mediated oxidative stress occurs in the pathogenesis and progression of melanoma, and that this imbalance in redox homeostasis appears to be functionally linked to microRNA-mediated non-mutational epigenetic reprogramming involving genes and transcription factors. The relationship between ROS-mediated stress control, tumour microenvironment and microRNAs expression in melanoma is not fully understood. The aim of this review is to analyze the involvement of miRNAs in the modulation of signalling pathways involved in ROS-mediated oxidative stress in melanoma. It is hoped that these considerations will contribute to the understanding of the mechanisms associated with a potential epigenetic network regulation, where the modulation of oxidative stress is consolidated as a common factor in melanoma and therefore a potential footprint poorly documented.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

In this work, optimal consumption and investment strategies are derived for risk-averse investors under the 4/2 stochastic volatility class of models. We work under an expected utility (EUT) framework and consider a Constant Relative Risk Aversion (CRRA) investor, who might also be ambiguity-averse. The corresponding Hamilton-Jacobi-Bellman (HJB) and HJB-Isaacs (HJBI) equations are solved in closed-form for a subset of the parametric space and under some restrictions on the portfolio setting, for complete markets. Conditions for proper changes of measure and well defined solutions are provided. These are the first analytical solutions for the 4/2 stochastic volatility model and the embedded 3/2 model for the type of excess returns established in .

This short paper reveals a simple methodology to create local-correlation models suitable for the closed-form pricing of multi-asset financial derivatives. The multivariate models are built to ensure two conditions, first, marginals follow desirable processes, e.g. we choose the Geometric Brownian Motion (GBM), popular for stock prices. Second, the payoff of the derivative should follow a desired one dimensional process. These conditions lead to a specific choice of the dependence structure, in the form of a local-correlation model. Two popular multi-asset options are entertained, a spread option and a basket option.

This paper presents a novel integration of Systems Engineering (SE) methodologies and Industry 4.0 (I4.0) technologies in the design of robotic systems, with a focus on enhancing underwater robotic missions. Using the conceptual design of an underwater exploration vehicle as a case study, we demonstrate how SE can systematically incorporate I4.0 tools to improve mission performance and meet stakeholder expectations. The study begins with an overview of the SE approach, emphasizing the conceptual design stage, aligning with the application and case study of design theories. We then explore various I4.0 technologies, highlighting their functional benefits rather than technical specifics, addressing design methods for Industry 4.0. Remotely Operated Vehicles (ROVs) are examined in terms of classification, components, and tasks, showcasing their evolution driven by technological advancements, thus tackling the complexity and design of complex systems. The core of our study involves defining stakeholder expectations, using quality function deployment for requirements definition, and performing a functional and logical decomposition of the ROV system. Our approach underscores the importance of understanding and integrating new technologies functionally, aligning with the transition towards Industry/Society 5.0. This work not only illustrates the synergy between SE and I4.0 but also offers a structured methodology for advancing the design and functionality of complex systems, setting a blueprint for future developments in this field.

In this work, we will study at a basic level, a series of possible new three-dimensional monoclinic allotropes of silicon, with sp3 hybridization, of the bct type; where hexahedrons and octahedrons are combined, with other cluster shapes, with basic silicon geometries such as: triangles ( Si3 ), squares ( Si4 ), pentagons ( Si5 ) and hexagons ( Si6 ); similar to two-dimensional, sp2 hybridized graphene allotropes. Calculating its electron density, bandgap energy and electronic mobility.

In this work, we will study metallic clusters equivalent to the organic ones intercalated with metals, of solid benzene type, Ba anthracene and K3.45picene; and we will try to calculate its superconducting Tc, for each of these compounds, from electronic correlations at room temperature. We will also study metal hydrides and clusters, totally composed of metals, which adopt forms analogous to molecular organic picene and anthracene; also calculating its TC.

Climate change has become a major concern for developing countries given the risk that it posses on energy and food independence, and on general productivity. Despite having an energy system with low carbon intensity when compared to other Latin American countries, Colombia is already facing climate change impacts and requires urgent efforts to mitigate them. As a developing country, the challenge is bigger as policies for economic growth should be in line with the global commitment of reducing greenhouse gas emissions. With the aim of contributing to the design of climate policies, this study assesses the impact of economic development on the environment by examining the validity of the Environmental Kuznets Curve hypothesis for Colombia. Statistically validated and stable autoregressive distributed lag models are estimated for three different environmental indicators: carbon dioxide emissions, methane emissions, and ecological footprint. Moreover, the effects of other variables such as urbanization, foreign direct investment, value added of agricultural and industrial sectors, and energy use are analyzed with dynamic simulations. Empirical evidence supports a long-run equilibrium relationship among investigated variables and the existence of an inverted U-shaped EKC relationship between Gross Domestic Product (GDP) and methane emissions, and GDP and ecological footprint. Shifting to renewable energy sources and leveraging the use of cleaner technologies in agricultural and industrial sectors are found to be key for economic growth without harming the environment.

We present a thermodynamic approach in modeling the evolution of the universe based on a theory that space consists of energy quanta, the spaceons. From wave-particle duality, they can be treated as an ideal gas. The model is similar to the Big Bang but without Inflation. It provides an insight into the nature of dark energy and dark matter, and an explanation for the accelerated expansion of the universe. The universe started from an atomic size volume of spaceons at very high temperature and pressure. Upon expansion and cooling, phase transitions occurred resulting in the formation of fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters due to the action of gravity. From the cooling curve of the universe we constructed a thermodynamic phase diagram of cosmic composition, from which we obtained the correlation between dark energy and the energy of space. Using Friedmann’s equations, our model fits well the WMAP data on cosmic composition with an equation of state parameter, w= -0.7. The dominance of dark energy started at 7.25 x 10⁹ years, in good agreement with BOSS measurements. The expansion of space is attributed to a scalar quantum space field. Dark Matter is identified as a plasma form of matter similar to that which existed during the photon epoch, prior to recombination. The thermodynamics of expansion of the universe was adiabatic and decelerating during the first 7 billion years after the Big Bang; it accelerated thereafter. A negative pressure for Dark Energy is required to sustain the latter. This is consistent with the theory of General Relativity and the law of conservation of energy. We propose a mechanism for the acceleration as due to consolidation of matter forming Dark Energy Stars (DES) and other compact objects. The resulting reduction in gravitational potential energy feeds back energy for the expansion. Space will continue to expand and dark energy will undergo phase transition to a Bose-Einstein condensate, a superfluid form of matter. Self-gravitation can cause a bounce and start a new Big Bang. We show how the interplay of gravitational and space forces leads to a cyclic, maybe eternal, universe.

Objective: To identify risk factors(RF) related to abnormal glucose regulation(AGR) 3 years postpartum according to 3-month-postpartum glucose status. Research design: Normoglycemic pregnant women of the St. Carlos Gestational Study included before gestational week 12, during 2015-2017. Of 3,036 eligible women, 2529 were followed-up until delivery: 1400 participated in postpartum follow-up. AGR defined as fasting serum glucose (FSG)>5.6 mmol/L and/or HbA1c >5.7% (39 mmol/mol) and/or 2h-SG ≥140/mg/dL after 75-g OGTT. 12-modifiable and 3-unmodifiable RF were analyzed for associations with glycemic changes. Reinforcement of Mediterranean Diet adherence was provided to all women at the postpartum visit by a dietitian Results: 137/1400(9.8%) women presented AGR 3 years postpartum, 27/137(19.7%) also had at 3 months, whereas 110/137(80.2%) had not. The remaining 1,263(90.2%) women were normoglycemic 3 years postpartum, 1180/1263(84.3%) were at 3 months, while 83/1263(6.08%) had AGR and became normoglycemic. Women with GDM were more likely to progress to AGR 3 years postpartum (OR:1.60[1.33-1.92]) and less likely to remain normoglycemic (OR:0.22[0.15-0.33]) versus non-GDM women. Having >2/3 unmodifiable RF was associated with a reduced rate of maintained normoglycemia (OR:0.56[0.39-0.80]) and an increased risk of progression to AGR (OR:1.90[1.28-2.83]). Having >5/12 modifiable RF was associated with a reduced rate of maintained normoglycemic (OR:0.74[0.51-0.99]) and reversion of AGR (OR:0.49[0.25-0.97]), an increased progression to AGR (OR:1.40[1.00-2.09]), and persistence of AGR (OR:2.57[1.05-6.31]). Pre-gestational BMI≥25kg/m2 (OR:1.80[1.19-2.71]), post-delivery weight gain (OR:2.22[1.10-4.48]), and waist circumference >89.5cm (OR:0.54[0.36-0.79]), (all p<0.05) were the main modifiable RF. Conclusions: RF related to an increased probability for 3-year-postpartum AGR despite 3-month normoglycemia were identified, potentially useful when designing personalized strategies for pregnant women, directed towards minimizing unfavorable outcomes.

Microbial electrochemical technologies (MET) rely on the presence of the metabolic activity of electroactive bacteria for the use of solid-state electrodes for oxidizing different kind of compound, that could lead to the synthesis of chemicals, bioremediation of polluted matrices, the treatment of contaminants of interest, as well as the recovery of energy. Keeping in mind those possibilities, since the beginning of the present century, there has been a growing interest in the use of electrochemical technologies for wastewater treatment, and if possible with simultaneous power generation. In the last years, there has been a growing interest to explore the possibility of merging MET with constructed wetlands, to offer a new option of intensified wetland system that could keep a high performance with a lower footprint. Based on that interest, this paper explains the general principles of MET, and the different known extracellular electron transfer mechanisms ruling the interaction between electroactive bacteria and potential solid-state electron acceptors. Also, the adoption of those principles for the development of MET set-ups for simultaneous wastewater treatment and power generation, and the challenges that the technology face. Ultimately, the most recent developments in set-ups that merges MET with constructed wetlands are presented and discussed.

This study develops a structure for mapping native vegetation in a transition area between Brazilian Cerrado and Atlantic Forest from integrated spatial information from the Sentinel-1 and Sentinel-2 satellites. Most studies use this data separately, however, the integrated use of optical sensors with Synthetic Aperture Radar (SAR) sensors can improve the methodology for classifying land use and land cover (LULC). The fusion of Sentinel-1 and Sentinel-2, for example, can increase the accuracy of mapping algorithms, using complementary information, such as spectral, backscattering, polarimetry, and interferometry. The study area comprises the Lobo Reservoir Hydrographic Basin, which is part of an environmental conservation unit protected by Brazilian law and with significant human development. LULC were classified, using the random forest deep learning algorithm. The classifying attributes were backscatter coefficients, polarimetric decomposition, and interferometric coherence for radar data (Sentinel-1), and optical spectral data, comprising bands in the red edge, near infrared, and shortwave infrared (Sentinel-2). The attributes were evaluated in three settings in which the SAR and optical data were evaluated separately (C1 and C2, respectively) and in an integrated manner (C3). The study found greater accuracy for C3 (96.54%), an improvement of nearly 2% compared to C2 (94.78%) and more than 40% in relation to C1 (55.73%). The classification algorithm encountered significant challenges in identifying wetlandsin C1, but performance improved in C3, enhancing differentiation by stratifying a greater number of classes during training and facilitating visual interpretation during sampling. Accordingly, the use of SAR and optical data becomes an alternative to optimize LULC mapping in tropical regions, due to the limited influence of atmosphere on images in the microwave range.

Background: Bariatric surgery (BS) has a significant impact on body composition (BC) and con-sequently may affect established sarcopenic obesity (SO) in candidate patients. The aim of this study is to assess the utility of muscle ultrasound (MUS) of rectus femoris thickness (RFT) for the evalua-tion of BC and skeletal muscle function in patients undergoing BS compared to bioimpedance analysis (BIA), dual-energy X-ray absorptiometry (DEXA) and dynamometry. On the other hand, we aim to demonstrate how MUS of RFT correlates better with the quality of life (Qol) in this population, likely because it enables the detection of regional quadriceps muscle sarcopenia, in comparison to the other mentioned methods. Methods: This is a prospective pilot study including 77 subjects (64.9% female, mean age: 53.2 ± 8.67 years) who underwent BS. Handgrip strength was measured using a dynamometer, fat-free mass index (iFFM) was assessed by BIA, appendicular muscle index (AMI) was calculated using DEXA and RFT was measured by MUS. Moreover, Homeostasis Model Assessment of Insulin Resintance (HOMA-IR) was calculated. All these measurements were conducted 1 month prior to BS and at the 12-month follow-up. QoL was as-sessed using the Moorehead-Ardelt questionnaire. Results: The mean BMI decreased by 12.95 ± 3.56 kg/m2 (p=0.001). Firstly, we observed positive correlation pre-surgery between HOMA and: RFT (r=0.27, p=0.02), iFFM (r=0.36, p=0.001), AMI (r=0.31, p=0.01) and dynamometer (r=0.26, p=0.02). In addition, we found correlation between RFT and iFFM (pre-surgical: r=0.31, p=0.01; post-surgical: r=0.25, p=0.05) and between RFT and lower extremities AMI post-surgical (r=0.27, p=0.04). Secondly, we observed significant reductions in iFFM, AMI and RFT (p=0.001), but not with dynamometer (p=0.94). Finally, a tendency to a positive correlation between QoL question-naire and RFT post-surgery (r=0.23, p=0.079) was observed. Conclusions: Our results suggest that RFT measured by MUS for the evaluation of SO and the follow-up after BS of these patients. Moreover, RFT can provide relevant information about regional sarcopenia and probably has an accurate correlation with QoL in comparison with the other methods.

The purpose of this article is to analyze, in a three-stage research, the relationships between environmental expenses, the improvements achieved in 5 environmental variables analyzed and efficiency, from an economic and operational perspective. The stages of this research are analyzing the sustainability reports to determine the level of information, analyzing the economic and operational efficiency, and analyzing the alignment with the environmental priorities of the Eco Ports-ESPO (European Sea Ports Organization). The results reveal that (1) the type of traffic does not condition environmental actions; (2) environmental performance (improvements) depends on environmental expenditures; (3) environmental spending and efficiency in port operations are correlated; and (4) environmental spending and port economic efficiency are correlated.

Currently, companies and SMEs (small and medium enterprises) are looking to be more competitive. In order to achieve this, they are adopting new business models and strategies that allow them to move towards sustainability. Strategies such as CSR (Corporate social responsibility) and supply chain management have become essential for ensuring a company’s permanence and financial consolidation. The literature has stated that the theories of Stakeholders and Sustainability are fundamental pillars for the development and sustained growth of business. The purpose of this article is to examine the effects of CSR and the SC (supply chain) on innovation, image and reputation, and in turn, their influences on profitability in SMEs. This research is based on a sample of 143 companies in the city of Guaymas Sonora, in Mexico. For the analysis and validation of the results, we used the SEM (Structural Equation Modeling) statistical technique based on the variance, through PLS (Partial Least Squares) (using SmartPLS version 3.2.6 Professional). The findings show that SMEs that develop social and sustainable practices increase their level of innovation, and improve their image, their reputation, and their financial profitability. This work contributes mainly to the development of Stakeholders and Sustainability.

Soil amendments with composted organic materials are recommended to increase soil organic matter (SOM), promote soil fertility, and the Circular Economy. Growing areas of hedged olive groves in southern Iberia peninsula generate huge amounts of olive leaves whose potential as soil organic amendment is not fully studied. An experimental field trial in a hedged olive grove (cv. “Cobrançosa”) was set up near Portalegre, Portugal, to test a compost of olive leaves plus sheep manure (2:1) applied in the row, at soil surface. Three nominal rates (0 or control, 2.5 and 5.0 kg m-2) were used, in a complete randomized block setup (3 treatments, 3 replicas, 9 plots) and soil chemical properties of layers 0-5, 5-15, and 15-30 cm deep were annually monitored. Results (mainly in layer 0-5 cm) showed increases in total N, carbon of the particulate organic matter (POM-C), permanganate oxidizable carbon (POX-C), extractable phosphorus, and zinc, after one year, and increases in soil organic carbon (SOC), C-stock, pHKCl, extractable phosphorus, and zinc, after two years. POX-C was the most sensitive SOM-related indicator, showing increases up to 30 cm deep after one year. This compost improved soil fertility, but should be monitored over longer periods of time, namely for SOC and extractable zinc content.

Few Sclerophyllous plants from the central coast of Chile have been systematically studied. This work describes the phytochemical composition and antimicrobial properties of Baccharis concava Pers. (sin. B. macraei), a shrub found in the first line and nearby the pacific coast between latitudes 29-38⁰S. B. concava has been traditionally used by indigenous inhabitants of today central Chile for their anthelmintic properties, wound healing properties and as a diuretic. Hydro-alcoholic extracts of B. concava were prepared from leaves and small branches. The qualitative phytochemical characterization indicated presence of alkaloids, steroids, terpenoids, flavonoids, phenolic and tannins compounds. The antimicrobial activity of this extract was assessed in a panel of microorganisms including Gram-positive, Gram-negative bacteria and pathogenic yeasts. The extract displayed important antimicrobial effects against Gram positive, Candida albicans, and Cryptococcus neoformans, but not against Gram negative, for which an intact Lipopolysaccharide (LPS) is apparently the determinant of resistant to B. concava extracts. The hydroalcoholic extract was then fractionated through a sephadex LH-20/methanol-ethyl acetate column. Followed, the fractions were pooled according to a similar composition that was visualized by TLC/UV analysis. Fractions obtained by this criterion were assessed for their antimicrobial activity against Staphylococcus aureus. The fraction presenting the most antimicrobial activity was HPLC-ESI-MS/MS analyzed obtaining a composition rich in structures derived from caffeoylquinic acid, dicaffeoylquinic acid and quercetin, among others. In conclusion, the extracts of B. concava show a strong antimicrobial activity probably due to their composition rich in metabolites derived from caffeoylquinic acid and quercetin, that in turn could be responsible for helping with wound healing, as reported from its ancient cultural use. In addition, the development of antimicrobial therapies based in the molecules found in B. concava could help to combat infection caused by pathogenic yeasts and Gram-positive bacteria, without affecting the Gram-negative microbiota.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

There is a long standing ‘two times problem’ in that a satisfactory reconciliation between the time of physics and that of psychology has not been realized. A partial solution to the past/present/future phenomenon has been successfully given by the Hartle information gathering and processing system (IGUS) view. That model IGUS robot is enhanced here for the entire ‘two times problem’ to deal with not only the temporal experiences of the flow of time but also those of manifest time. A dualistic robot is proposed which has a veridical system of temporal experiences that are compatible with various spacetime cosmologies. It also has an illusory system of corresponding temporal experiences. This dualistic IGUS robot was made possible by discovering temporal experience within the brain that correspond to those of physics. The dualistic theory suggests that the veridical system, as a result of evolution, begets the illusory system to enhance behavioral adaptation. Thus, there is just one fundamental physical time which the brain does, indeed, possess and then enhances with illusory counterparts. Therefore, there should no longer be a need to reify illusory temporal experiences as modern spacetime cosmologies tend to do. Physical time already resides within human time.

Spent batteries recycling is an important way to obtain low-cost graphite. Nevertheless, the obtaining of crystalline graphite with a rather low density of defects is required for many applications. In the present work, high-quality graphites have been obtained from different kinds of spent batteries. Black masses from spent alkaline batteries (batteries black masses, BBM), and lithium-ion batteries from smartphones (smartphone black masses, SBM) and electric and/or hybrid vehicles (lithium-ion black masses, LBM) were used as starting materials. A hydrometallurgical process was then used to obtain recycled graphites by acidic leaching. Different leaching conditions were used depending on the type of the initial black mass. The final solids were characterized by a wide set of complementary techniques.

Background: Although confirmed cases of infection with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) have been declining since late 2020 due to general vaccination, little research has been done regarding the impact of vaccines against SARS-CoV-2 in Spain in terms of hospitalizations and deaths. Objective: Our aim was to identify the reduction in severity and mortality of coronavirus disease 2019 (COVID-19) at a nationwide level due to vaccination. Methods: We designed a retrospective, population-based study to define waves of infection and to describe the characteristics of the hospitalized population. We also studied the rollout of vaccination and its relationship with the decline in hospitalizations and deaths. Finally, we developed two mathematical models to estimate non-vaccination scenarios using machine learning modeling (with the ElasticNet and RandomForest algorithms). The vaccination and non-vaccination scenarios were eventually compared to estimate the number of averted hospitalizations and deaths. Results: In total, 498,789 patients were included, with a global mortality of 14.3%. We identified six waves or epidemic outbreaks during the observed period. We established a strong relationship between the beginning of vaccination and the decline in both hospitalizations and deaths due to COVID-19 in all age groups. We also estimated that vaccination prevented 170,959 hospitalizations (CI 95% 77,844–264,075) and 24,546 deaths (CI 95% 2,548–46,543) in Spain between March 2021 and December 2021. We estimated a global reduction of 9.19% in total deaths during the first year of COVID-19 vaccination. Conclusions: Demographic and clinical profiles changed over the first months of the pandemic. Patients over 80 years old and other age groups obtained clinical benefit from early vaccination. The severity of COVID-19, in terms of hospitalizations and deaths, decreased due to vaccination.

The main aim of this work is to compare and characterize the state of decay developed in a set of 14 monuments, including churches and Pazos (Galician traditional house) of the architectural heritage of the Barbanza Peninsula (Galicia), considering its relationship with the influence of the environmental factor. A macroscopic inspection was carried out to determine the deterioration patterns. The most reported pathology across the peninsula, due to the moisture regime, was the formation of dark areas (generally as biofilms) and the lichen growth (biological colonization). Depending on the proximity to the coast, the study area was divided into two zones. Zone 1, closer to the sea (&lt;1 km) with an important influence of sea salts and wind and zone 2, further from the sea with higher altitudes (center of the peninsula) and important rainfall, humidity and therefore, fauna growth. Crusts (to a lesser degree, because it is a mainly rural area) are more frequent in zone 1, but the state of conservation of stone is better than in zone 2 due to the concentration of urban centers that require aesthetics and constant maintenance. In zone 2, however, abandonment is greater and biological colonization (mainly by lichens and plants) is more developed along with deterioration patterns due to biological damage. The synergy of several factors such as salt, climatic conditions and spatial characteristics of the architectural heritage studied define the degree of deterioration of each heritage objective. The research has a potential contribution to the conservation measures to be undertaken.

Background and objective: Addressing the global morbidity associated with pulmonary disease is an important need for the respiratory community. However, there is also a growing momentum to show the efficacy of new tools of diagnosis. Despite this, there are few physiotherapeutic tools that help identify and categorize these conditions. The aim was to analyze the variables of physiotherapy index of the ventilatory workload (PIVW) in people with chronic obstructive pulmonary disease (COPD) during stability and exacerbation in an outpatient setting. Material and Methods: Analyzed retrospectively of 198 clinical records were reviewed. The PIVW was extracted in stability and exacerbation of these patients with COPD. After applying the exclusion and inclusion criteria; 54 patients were classified. Through the statistical analysis of chi-square, a significant association was reported for each of the variables and the total PIVW score. Results: when analyzing the baseline with the peak of PIVW, there was a significant increase in patients COPD exacerbation. Similarly, the variables that constitute the loads, translations and supports underwent a significant increase from baseline to exacerbation (p<0.0001), except for the additional oxygen contribution, where the frequency of patients was the same in basal and exacerbation as well. Conclusions: the PIVW, serves to determine ventilatory problemas in outpatients, characterizing the specific changes of loads, translators or assistance.

In recent years, research has noted the increasing prevalence of mental health problems among university students. The current mental health needs of the university population, along with the multitude of stressors they face, increase the importance of examining their psychological well-being and determining the personal resources that effectively promote it. In this context, the present research aims to analyze the role of psychological capital (PsyCap) and coping strategies as personal resources facilitating psychological well-being (PWB) of university students. Specifically, the mediating role of coping strategies (both adaptive and maladaptive) in the relationship between PsyCap and PWB is explored. The study involved 391 university students from Spain. The results found a partial mediation effect of adaptive coping strategies on the relationship between PsyCap and PWB. Likewise, PsyCap was shown to be a direct positive predictor of adaptive coping strategies and PWB, as well as a direct negative predictor of maladaptive coping strategies. Therefore, it is concluded that PsyCap serves as a valuable personal resource that enhances and strengthens PWB in university students, as well as adaptive coping strategies. PsyCap also decreases the tendency to engage in maladaptive coping strategies. Similarly, the use of adaptive coping strategies contributes to improving students' PWB.

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

CO₂ geological storage in deep saline aquifers was recently developed at industrial scale mainly in sandstone formations. Experiences on CO₂ injections in carbonates aquifers for permanent trapping are quite limited, mostly from US projects such as AEP Mountaineer, Michigan and Williston Basin. The behavior of fractures in carbonates plays a key role in those reservoirs in which porous matrix permeability is very poor, which drives the CO₂ plume migration through the fracture network where hydromechanics and geochemical effects take place due to injection. Hontomín (Spain) is the actual on-shore injection pilot in Europe (EP Resolution of 14 January 2014), whose reservoir is comprised of fractured carbonates. Existing experiences from field scale tests conducted on site have supported to better understand the behavior of this type of reservoirs for CO₂ geological storage. Innovative CO₂ injection strategies are being carried out in ENOS Project (EU H2020 Programme, http://www.enos-project.eu). First results based on field tests conducted at Hontomín, and the advanced modelling developed so far will be analyzed and discussed in this article, as well as, the description of future works. The evolution of operating parameters such as flow rate, pressure and recovery term during the tests confirm the CO₂ migration through the fractures.

This paper investigates the integration of SHM within the frame of Industry 4.0 technologies, highlighting the potential for intelligent infrastructure management through the utilization of Big Data analytics, Machine Learning, and the Internet of Things (IoT). The study also presents a success case focused on a novel SHM methodology for detecting and locating damages in metallic aircraft structures, employing dimensional reduction techniques such as Principal Component Analysis (PCA). By analyzing strain data collected from a network of sensors and comparing it to a baseline pristine condition, the methodology aims to identify subtle changes in local strain distribution indicative of damage. Through extensive Finite Element Analysis (FEA) simulations and a PCA contribution analysis, the research explores the influence of various factors on damage detection, including sensor placement, noise levels, and damage size and type. The findings demonstrate the effectiveness of the proposed methodology in detecting cracks and holes as small as 2mm in length, showcasing the potential for early damage identification and targeted interventions in diverse sectors such as aerospace, civil engineering, and manufacturing. Ultimately, this paper underscores the synergistic relationship between SHM and Industry 4.0, paving the way for a future of intelligent, resilient, and sustainable infrastructure.

We believe that a natural focus of the Physics Education Research community is on understanding and improving student learning in our physics courses. For this purpose, we are introducing smartphones in the physics laboratory. Current smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. In this work, we have considered the magnetic field created by a linear quadrupole and we have studied its dependence on distance. Using an experimental procedure that is simple we have measured the magnetic field using the Hall sensor that most smartphones have, together with the corresponding app. The purpose of this work is to show that the laboratory is a powerful tool that increases significant learning under three conditions: 1) the practice must not be too sophisticated; 2) students must handle objects in the lab; and 3) the practice must be scientifically accurate, including the adjustments by minimum squares, and the following and necessary error calculation.

La integration (at various nominal contents) in SBA-15 prepared under acidic medium was intended from corresponding direct nitrate addition during mesoporous silica formation. Materials were impregnated with Pt (1.5 w%) and studied through several textural (N2 physisorption), structural (XRD, TG-DTG) and surface (FTIR, STEM-HAADF, SEM-EDS, NH3 and CO2 TPD) instrumental techniques. Pt-impregnated solids were tested in phenol hydrodeoxygenation (HDO, T=250 °C, 3.2 MPa, batch reactor, n-decane as solvent). Catalytic activity (in pseudo first order kinetic constant, kHDO basis) was related to Pt dispersion which was, however, not determined by nominal rare earth content. Determining actual composition of modified SBA-15 materials is crucial in reaching sound conclusions regarding their physicochemical properties, especially when La modifier is directly added during mesoporous matrices formation where efficient interaction among constituents could be difficult to get. Otherwise, results from some characterization techniques (N2 physisorption and FTIR, for instance) could be misleading and even contradictory. Indeed, extant modifier precursors when under SBA-15 synthesis conditions could affect the properties of prepared materials even though they were absent in obtained| formulations. Performing a simple compositional analysis could eliminate uncertainties regarding the role of various modifiers on characteristics of final catalysts. However, several groups have failed in doing so.

Endurance triathlons impose substantial physiological stress, yet effects of short-course formats remain relatively unexplored. In this preliminary study, we assessed proteinuria and hydration levels in 27 well-trained triathletes (41.9 [7.4] years) who completed a sprint triathlon consisting of a 1500-m swim, 26-km cycle, and 8-km run. Urine samples were collected before and after the race. The results showed an increase in cases of post-race proteinuria from four to nine (p=0.03). Also, one case of urobilinuria and ketoacidosis was observed after the race. Pre-race glucosuria, which was present in nine cases, decreased to three cases post-race. Although hematuria cases decreased from six to two (p=0.13), pre-race leukocyturia (found in two cases) resolved post-race. There was a significant increase in urine specific gravity (from 1.018 to 1.023, p=0.03), indicating dehydration. In conclusion, short-course triathlons were found to induce post-race proteinuria, urobilinuria, and dehydration without exacerbating pre-race glucosuria, hematuria, or leukocyturia. These preliminary findings contribute to our understanding of medical guidelines for sprint triathlons, an area of endurance sports that has received limited research attention. Further investigation, both mechanistic and longitudinal, is warranted in this regard.

Synthesis of nickel oxide nanoparticles (NiO NPs) is a low cost and ecofriendly route that brings great benefits over chemical and physical methods of synthesis. Our approach consisted of using aqueous extracts from treated waste of Manihot Esculenta (Cassava) as reducing, stabilizing and capping agents for the synthesis of NiO NPs. The results proved this approach might be a viable alternative. Extracts were mixed during 30 minutes with Ni(NO3)2.6H2O leading to NPs formation. NiO NPs were characterized through FTIR, XRD, TEM and Raman spectroscopy. NiO NPs showed different shapes and sizes around 5-10 nm in agreement with the particle size calculated by XRD Scherrer equation.

The process of establishing secure communication between devices in the Internet of Things (IoT) can be approached by using a One-time-Pad (OTP) protocol. We propose using a known secure multiparty sum protocol for generating a One-time-Pad key using true (physical) random numbers in each device (party). We implemented the proposal using ZeroC-Ice, a middleware for distributed computing. The protocol security properties were analyzed under the assumptions of the Dolev-Yao threat model.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

The Covid-19 pandemic has produced a change in the way of living, socializing and a modification in Health Systems around the world. A multicentre retrospective study was carried out to study orofacial trauma in one of the regions most affected during the first wave of the pandemic, with the participation of the five main tertiary hospitals in Madrid. The aim of this study is to evaluate the epidemiology of orofacial surgical trauma during the 1 year of COVID pandemic and compared to de prior year. Age, sex, mechanism, localization, and treatment were studied. P-value <0.05 was considered statically significative. Reduction of 39.36% (<0.001) in maxillofacial fractures was observed, without significance change in sex, localization or treatment. Significant increase in age (35,92 vs. 40,26) (p = 0.006) was observed. Significant decline in mechanism was noted (p = 0.025), decreasing personal violence (41% vs 35%) and sports (14% vs 8%); increasing in falls (27% vs 35%), precipitation (2 vs 5%), and traffic accidents (12% vs 13%). The mandible was the most frequent fractured bone. The COVID pandemic has produced epidemiological variations in orofacial trauma, making it necessary to monitor social and legal changes that may require reorganization to adjust to population needs.

Helicobacter pylori cytotoxin-associated gene A protein (CagA) has been associated with the increase in virulence and risk of cancer. It has been demonstrated that CagA's translocation is dependent on its interaction with phosphatidylserine. We evaluated the variability of the N-terminal CagA in 127 sequences reported in NCBI, by referring to molecular interaction forces with the Phosphatidylserine and the docking of 3 mutations chosen from variations in specific positions. The major sites of conservation of the residues involved in CagA-Phosphatidylserine interaction were 617, 621 and 626 which had no amino acid variation. Position 636 had the lowest conservation score, so mutations in this position were evaluated to observe the differences in intermolecular forces of the CagA-Phosphatidylserine complex. We evaluated the docking of 3 mutations: K636A, K636R and K636N. The models of the crystal and mutations presented a ΔG of −8.919907, −8.665261, −8.701923, −8.515097 Kcal/mol, respectively, while mutations K636A, K636R, K636N and the crystal structure presented 0, 3, 4 and 1 H-bonds, respectively. Likewise, the bulk effect of the ΔG and amount of H-bonds was estimated in all of the docking models. The type of mutation affected both the ΔG (χ²(1) = 93.82, p-value < 2.2 × 10⁻¹⁶) and the H-bonds (χ²(1) = 91.93, p-value < 2.2 × 10⁻¹⁶). In all the data, 76.9% of the strains that exhibit the K636N mutation produced a severe pathology. The average H-bond count diminished when comparing the mutations with the crystal structure of all the docking models, which means that other molecular forces are involved in the CagA-Phosphatidylserine complex interaction.

Groundwater flow and transport models are essential tools for assessing and quantifying the mi-gration of organic contaminants at polluted sites. Uncertainties in the hydrodynamic and transport parameters of the aquifer have a significant effect on model predictions. Uncertainties can be quantified with advanced sensitivity methods such as Sobol’s High Dimensional Model Reduction (HDMR) and Variogram Analysis of Response Surfaces (VARS). Here we present the application of VARS and HDMR to assess the global sensitivities of the outputs of a transient groundwater flow model of the Gállego alluvial aquifer which is located downstream the Sardas landfill in Huesca (Spain). The aquifer is subject to the tidal effects caused by the daily oscillations of the water level in the Sabiñánigo reservoir. Global sensitivities are analysed for hydraulic heads, aquifer/reservoir fluxes, groundwater Darcy velocity and hydraulic head calibration metrics. Input parameters in-clude aquifer hydraulic conductivities and specific storage, aquitard vertical hydraulic conductiv-ities, and boundary inflows and conductances. VARS, HDMR and graphical methods agree to identify the most influential parameters which for most of the outputs are the hydraulic conduc-tivities of the zones closest to the landfill, the vertical hydraulic conductivity of the most permeable zones of the aquitard, and the boundary inflow coming from the landfill. The sensitivity of heads and aquifer/reservoir fluxes with respect to specific storage change with time. The aquifer/reservoir flux when the reservoir level is high shows interactions between specific storage and aquitard conductivity. VARS and HDMR parameter rankings are similar for the most influential parameters. However, there are discrepancies for the less relevant parameters. The efficiency of VARS was demonstrated by achieving stable results with a relatively small number of simulations.

The tourism sector in general and the hotelier in particular face the challenge of managing appropriate measures to deal with the covid-19 pandemic. In this sense it is useful to know what the measures are most demanded by the clientele. This research, by analyzing the variance (ANOVA) of a factor concluded that women are more demanding than men in terms of the level of demand in relation to the measures to be taken in hotels. This, as a practical application, allows to know more accurately the expectations, demands and demands of the client segmented by sex, in order to satisfy and improve the tourist experiences.

The tourism sector in general and the hotelier in particular face the challenge of managing appropriate measures to deal with the covid-19 pandemic. In this sense it is useful to know what the measures are most demanded by the clientele. This research, by analyzing the variance (ANOVA) of a factor concluded that women are more demanding than men in terms of the level of demand in relation to the measures to be taken in hotels. This, as a practical application, allows to know more accurately the expectations, demands and demands of the client segmented by sex, in order to satisfy and improve the tourist experiences.

The tourism sector in general and the hotelier in particular face the challenge of managing appropriate measures to deal with the covid-19 pandemic. In this sense it is useful to know what the measures are most demanded by the clientele. This research, by analyzing the variance (ANOVA) of a factor concluded that women are more demanding than men in terms of the level of demand in relation to the measures to be taken in hotels. This, as a practical application, allows to know more accurately the expectations, demands and demands of the client segmented by sex, in order to satisfy and improve the tourist experiences.

Single-particle cryo-electron microscopy (cryo-EM SPA) has recently emerged as an exceptionally well-suited technique for determining the structure of membrane proteins (MPs). Indeed, in the last years, it was observed a huge increase in the number of MPs solved by cryo-EM SPA at a resolution better than 3.0 Å in the Protein Data Bank (PDB). However, sample preparation remains a significant challenge in the field. Here, we evaluated in the MPs solved by cryo-EM SPA deposited in the PDB in the last two years at a resolution below 3.0 Å the most critical parameters for sample preparation: i) the surfactant used for protein extraction from the membrane, ii) the surfactant, amphiphiles, nanodiscs or other molecules present in the vitrification step, iii) the vitrification method employed, and iv) the type of grids used. The aim is not to provide a definitive answer on the optimal sample conditions for cryo-EM SPA of MPs, but rather assess the current trends in the MP structural biology community towards obtaining high-resolution cryo-EM structures.

In this article, we delve into the intricate behavior of electronic mechanisms underlying NMR magnetic shieldings, σ, in molecules containing heavy atoms such as cadmium, platinum, and mercury. Specifically, we explore PtXn^{−2} (X = F, Cl, Br, I; n = 4, 6) and XCl2 Te2 Y2 H6 (X = Cd, Hg; Y = N, P) molecular systems. It is known that the leading electronic mechanisms responsible for the relativistic effects on σ are well characterized by the linear response with elimination of small components model (LRESC). In this study, we present results obtained from the innovative LRESC-Loc model, which offers the same outcomes as the LRESC model but employs localized molecular orbitals (LMOs) instead of canonical MOs. These LMOs provide a chemist’s representation of atomic core, lone pairs, and bonds. The whole set of electronic mechanisms responsible of the relativistic effects can be expressed in terms of both non-ligand-dependent and ligand-dependent contributions. We elucidate the electronic origins of trends and behaviors exhibited by these di- verse mechanisms in the aforementioned molecular systems. In PtX4^{−2} molecules, the predominant relativistic mechanism is the well-established one-body spin-orbit (σ^SO(1) ) mechanism, while the paramagnetic mass-velocity (σ^Mv ) and Darwin (σ^Dw ) contributing mechanisms also demand con- sideration. However, in PtX6−2 molecules, the σ Mv+ Dw contribution surpasses that of the SO(1) mechanism, thus influencing the overall ligand-dependent contributions. As for complexes con- taining Cd and Hg, the ligand-dependent contributions exhibit similar magnitudes when nitrogen is substituted with phosphorus. The only discrepancy arises from the σ^SO(1) contribution, which changes sign between the two molecules due to the contribution of bond orbitals between the metal and tellurium atoms.

The aim of this research work consisted of assessing the effects of the COVID-19 pandemic on the interurban public transport system in a rural region with a sparse population density, considering the number of tickets sold and passengers in each locality, as well as the different connecting lines. From a methodological point of view and with the intention of identifying patterns to explain the behaviour of both routes and passengers, a series of variables were selected, becoming determining factors that sought to offer a solution to the search for a common trend. Additionally, data processing by means of statistical analysis and the application of Geographic Information Systems (GIS) tools complemented the procedure. The results obtained in the investigation were provided both by municipality and by interurban route. An interesting finding of the research was the uneven recovery of the municipalities. The localities closest to the attractor nucleus have recovered more quickly to pre-pandemic mobility levels due to their geographical proximity, larger population, higher income per household and the need to access certain public services. In terms of routes, all lines showed significant decreases in ticket sales, although with variations. Although passenger numbers have shown a gradual recovery, the initial loss was considerable, and pre-pandemic normality has not been completely achieved. The authors consider that future research should include other alternative means of transport in these interurban areas, incorporating variables to characterise passengers, such as age, gender...etc.

At present, business strategies in SMEs (Small and medium enterprises) are crucial for consolidation in highly competitive markets, in achieving a better image and in business profitability. One of the strategies that have the most success and business success are sustainable practices and social responsibility such as: ISO 14001 and ISO 26001. The literature related to sustainable business is based mainly on the theory of resources and capabilities, and in theory based on Stakeholders. These currents state that companies should focus on profitable strategies to ensure significant and long-term results, in order to achieve organizational and financial results for stakeholders. In this work, the sample consists of 215 companies from the commerce, services and industry sectors, located in the southern region of the State of Sonora in Mexico. The objective of the work is to analyze the influence of ISO 14001 and 26001 standards on the image and profitability of SMEs. The statistical analysis of the data has been carried out through the linear regression technique by OLS (Ordinary Least Squares). The findings prove that the ISO 14001 standard is the one that most influences the improvement of the business image and the level of profitability of the SME. In addition, we discovered that ISO 26001 has a partial influence on the image and profitability of the SME.

This study explores the impact on the stability of drying and encapsulation of a camu camu extract (CCX) using the non-thermal, high-throughput electrospraying assisted by pressurized gas (EAPG) technique. The dried and encapsulated products by the EAPG processing techniques were compared in terms of total soluble phenolic compounds, antioxidant activity, and storage stability. Whey protein concentrate (WPC) and zein (ZN) were selected as the protective excipients for encapsulation. Dried and encapsulated products were obtained in the form of microparticles, which were smaller and more spherical in the case of the encapsulates. No significant differences were observed in the total polyphenolic content (TSP), and only relatively small differences in the antioxidant capacity were measured among samples. The generated products were subjected to various storage conditions to assess their stability and the preservation of the TSP and the antioxidant properties, i.e. 0% relative humidity (RH) and 4°C; 0% RH and 21°C; 23% RH and 21°C; 56% RH and 21°C; and UV light exposure. The results indicated that ZN encapsulation notably enhanced the retention of total soluble polyphenols and antioxidant activity compared to WPC and dried CCX, especially in the ratio 2:1 (encapsulating polymer: dried CCX). This study demonstrates the potential of protein-based encapsulation, particularly using ZN, for stabilizing bioactive compounds against degradation mechanisms induced by humidity, temperature, or ultraviolet radiation exposure.

Like many coastal lagoons in several countries, “Navío Quebrado” lagoon (La Guajira-Colombia) is a very delicate and precious environment; indeed, it is a nationally recognized Flora and Fauna Sanctuary. Several factors, amongst which climate change, are threatening its existence because of changes in the governing hydro-morphological processes. A first step to address this problem certainly is to understand its hydrological behavior and to be able to replicate via simulation its recent history and then infer likely futures. These potential futures will be marked by changes in the water input by its tributary, the Camarones River, and by a modified water exchange with the sea, according to a foreseen sea level rise pattern, as well as by a different evaporation from the free surface, according to temperature changes. In order achieve the required ability to simulate future scenarios, data on the actual behavior have to be gathered, i.e. a monitoring system has to be set up, which to date is not existent. Conceptually, designing a suitable monitoring system is not a complex issue and seems easy to implement. However, the environmental and socio-cultural and socio-economic context makes every little step a hard climb. An extremely simple –almost “primitive”- monitoring system has been set up in this case which is based on very basic measurements of current velocity and water levels and a direct participation of local stakeholders, first of all the National Park unit of the Sanctuary. All this may clash with the latest groovy advances of science, like in situ automatized sensors, remote sensing, machine learning and digital twins, and certainly several improvements are possible and desirable. But it has strong positive points: it is providing surprisingly reasonable data and…it is working at almost zero additional cost. Several technical difficulties made this exercise interesting in itself and worth being shared. Its novelty lies in showing how old, simple methods may offer a working solution to new challenges. This humble experience may be of help in several other similar situations across the world.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

This review presents an updated overview of research concerning Leishmania protein structures, primarily sourced from the Protein Data Bank (PDB), that play a role in the metabolic pathways of the Leishmania parasite. Furthermore, we assess the current progress in the identification and development of bioactive chemical agents aimed at addressing this substantially overlooked tropical disease. We have analyzed experimental data obtained from in vitro, in vivo and in silico sources. This data has been categorized into four main areas: a) vector taxonomy and geographic distribution; b) parasite taxonomy and geographic distribution; c) enzymatic functions of proteins engaged in parasite/host interactions throughout various developmental stages (such as oxidoreductases, transferases, hydrolases, lyases, isomerases, ligases, and cytokines); and d) established and experimental treatments employing bioactive chemical compounds. Our objective is to establish a foundational point of reference for research efforts concentrating on the elucidation of interaction mechanisms and the processes of ligand-protein activation/inactivation, specifically linked to Leishmania infections. Consequently, we emphasize enzymes recognized for their involvement in the biochemical pathways incited during Leishmania infection episodes. This review encapsulates the current understanding, offering insights to inform and direct future explorations aimed at targeting proteins and pathways to enhance the management of Leishmania-related diseases.

From the linear Nash-Green fluctuations of background metric, we present the perturbation equations in an embedded four space-time. In the context of a five-dimensional bulk, we show that the perturbations are only propagated by the gravitational tensorial field equation. In a Newtonian conformal gauge, we study the matter density evolution in sub-horizon regime and on how such scale may be affected by the extrinsic curvature. We use the "extended Gold 2018'' growth dataset with 25 datapoints and the best fit Planck2018/LambdaCDM parameters. Hence, we determine the evolution equation for the density growth delta(a) as a result from the embedded equations of the background geometry. By using solar constraints, we analyse the evolution of the effective Newtonian constant G_eff and showing that applying Taylor expansion to G_eff (a) under the constraint of time-derivative of G_eff(0)=G at a= 1 in matter domination era, we get an agreement with Big Bang Nucleosynthesis (BBN) and also an alleviation of the 3-sigma tension to 1-sigma contour between (sigma8-Omega_m) of the observations from Cosmic Microwave Background (CMB) and Large Scale Structure (LSS) probes.

The Baculoviridae, a family of insect-specific large DNA viruses, is widely used in both biotechnology and biological control. Its applied value stems from millions of years of evolution influenced by interactions with their hosts and the environment. To understand how ecological interactions, have shaped baculovirus diversification, we reconstructed a robust molecular phylogeny using 217 complete genomes and ~580 isolates for which at least one of four lepidopteran core genes was available. We then used a phylogenetic-concept-based approach (mPTP) to delimit 165 baculovirus species, including 38 species derived from new genetic data. Phylogenetic optimization of ecological characters revealed a general pattern of host conservatism punctuated by occasional shifts between closely related hosts and major shifts between lepidopteran superfamilies. Moreover, we found significant phylogenetic conservatism between baculoviruses and the type of plant growth (woody or herbaceous) associated with their insect hosts. In addition, we found that colonization of new ecological niches sometimes led to viral radiation. These macroevolutionary patterns show that besides selection during the infection process, baculovirus diversification was influenced by tritrophic interactions, explained by their persistence on plants and interactions in the midgut during horizontal transmission. This complete eco-evolutionary framework highlights the potential innovations that could still be harnessed from the diversity of baculoviruses.

A frequent problem in Geotechnics is the soils with inadequate physical-mechanical properties before the efforts to which they will be subjected by the constructions, incurring cost overruns caused by their engineering improvement. The need to improve the engineering properties of soils is not recent, currently observing that the most common alternatives are binders such as cement and lime. The climate change observed in recent decades and the uncontrolled emission of greenhouse gases have motivated Geotechnical and Geoenvironmental researchers to seek mechanisms for soil reinforcement from a more sustainable and environmentally friendly approach by proposing the use of recycled and waste materials. An alternative is natural fibers, which can be obtained as waste from many agro-industrial processes, implying their high availability and low cost. Sawdust as a by-product of wood processing has a rough texture that can generate high friction between the fiber and the matrix of the soils, leading to a significant increase in its shearing strength and bearing capacity. This concept of improving the properties of soils using natural fibers distributed randomly is inspired by the natural phenomenon of grass and/or plants that when growing on a slope can effectively stabilize a said slope.

The cultural and historical heritage of a city is a major resource to attract tourists. Therefore, reaching out to perceive and identify the characteristics of persons visiting a locality attracted by their property is relevant for the purpose of better meeting their expectations and needs. This research focuses on knowing the perceptions, motivations and satisfaction of women visiting Cordoba (Spain). Thus, on the basis of the questionnaire carried out on women visiting Cordoba during the months of June and November 2019, a statistical analysis has been made. Using various multivalent case-grouping techniques, tourist segments with similar perceptions of cultural heritage have been detected. Moreover, non-parametric statistical techniques have showed up significant differences between the valuations obtained in the various segments. This analysis has exposed a segment of women who, known as absorbent tourists, are characterized by the high cultural motivation to visit the city of Cordoba linked to the heritage they have visited. The conclusions obtained should be useful in adjusting the city's tourist supply to the specific demand of a population sector such as women visiting the city.

Carbon monoxide (CO) is a cytoprotective endogenous gas that is ubiquitously produced by the stress response enzyme heme-oxygenase. Being a gas, CO rapidly diffuses through tissues and binds to hemoglobin (Hb) increasing carboxyhemoglobin (COHb) levels. COHb can be formed in the erythrocytes or in plasma from cell-free Hb. Herein, it is discussed whether endogenous COHb is or is not an innocuous and inevitable metabolic waste product and it is hypothesized that COHb has a biological role. In the present review literature data is presented to support this hypothesis based on two main premises: (i) there is no direct correlation between COHb levels and CO toxicity; and (ii) COHb seems to have a direct cytoprotective and antioxidant role in erythrocytes and in hemorrhagic models in vivo. Moreover, CO is also antioxidant by generating COHb, which protects against the pro-oxidant damaging effects of cell free Hb. Up to now COHb has been considered as a sink for both exogenous and endogenous CO generated during CO intoxication or heme metabolism, respectively. Hallmarking COHb as an important molecule with a biological (and eventually beneficial) role is a turning point on CO Biology research, namely in CO intoxication and CO cytoprotection.

This paper introduces the implementation of a genetic programming (GP)-based procedure to the automatic design and tuning of process controllers. The proposed approach makes a significant contribution to the field of artificial intelligence (AI) in control engineering. Unlike other controller design methods, the GP-based program handles the entire design in the time domain, including differential operations like derivatives and integrals, without the need for intermediate inverse Laplace transformation. This approach not only simplifies the design process but also ensures that all generated controllers are implementable in physical systems. Furthermore, GP’s functions set includes various mathematical operations beyond basic arithmetic operators, such as trigonometric, exponential, and logarithmic operators. The performance and validity of the resulting controllers generated by the proposed GP-based approach are evaluated by verifying whether the generator can replicate the structure and performance of those produced by traditional controller design methods and, in some cases, achieve even better results. As a result, the GP-based approach presents a promising solution for automating the controller design process and addressing control problems in various engineering applications.

Prior work has suggested that discrimination and immigration-related stress may impede mental health care seeking and utilization among Latinx populations. These effects may be more nuanced as both discrimination and immigration-related stress may increase symptomology, particularly posttraumatic stress disorder (PTSD) and depression. Both symptoms may in turn prompt attempts to seek care. The current study examined the direct effects of discrimination and immigration-related stress on care access, as well as potentially indirect effects with PTSD and depression symptoms as mediators. Interviews and online surveys were completed with 234 Latinx residents of the Midwest assessing everyday discrimination, discrimination in healthcare, PTSD symptoms, depression symptoms, current mental health utilization, and previous unsuccessful attempts to seek care. Direct effects of discrimination and immigration-related stress were largely unrelated to care access variables. Discrimination in healthcare settings predicted both unsuccessful attempts to seek care and current use, but this effect was positive. The indirect effect was largely supported, but only for PTSD symptoms and not depression. Results indicate further investigation is necessary to understand the direct effects of discrimination on care access. Further, discrimination and immigration-related stress may indirectly prompt attempts to seek mental health care.

Motivated by the fact that the restrictive conditions for a Turing instability are relaxed in sub- diffusive regime, we investigate the effects of subdiffu- sion in the predator−prey model with toxins under the homogeneous Neumann boundary condition. First, the stability analysis of the corresponding ordinary differ- ential equation is carried out. From this analysis, it fol- lows that stability is closely related to the coefficient of toxicity. In addition, the temporal fractional derivative does not systematically widen the range of parameters to maintain a point in the stability domain. Further- more, we derive the condition which links the Turing instability to the coefficient of toxicity in the subdif- fusive regime. System parameters are varied in order to test our mathematical predictions while comparing them to ecological literature. It turns out that the mem- ory effects, linked to the transport process can, depend- ing on the parameters, either stabilize an ecosystem or make a completely different configuration.

Information theory has been developed for seventy years with technological applications that have transformed our societies. The increasing ability to store, transmit, and process information is having a revolutionary impact in most disciplines. The goal of this work is to compare the formal approach to information with Buddhist philosophy. Considering both approaches as compatible and complementary, I argue that information theory can improve our understanding of Buddhist philosophy and vice versa. The resulting synthesis leads to a worldview based on information that overcomes limitations of the currently dominating physics-based worldview.

As the novel COVID-19 disease spreads around the world, the most affected population are those who suffer from the most common chronic diseases, such as obesity, hypertension, and type 2 diabetes, which are quite associated with the so-called age-related diseases. On the other hand, since the Spanish influenza outbreak, humanity has not experienced an infectious disease that synergizes so quickly with chronic diseases, making it mortal for those individuals with comorbidities. In this context, COVID-19 is challenging for health systems all around the world due to the high prevalence of chronic diseases. Nowadays, we are facing the beginning of a new era in which health infectious and chronic diseases meet. Therefore, epidemiologic and biomedical researchers must work together to solve further contingencies, and politicians should direct science-centered decisions on public health. In the present paper, we make an urgent call to learn from the COVID-19 lessons in order to mitigate the chronic diseases prevalence and to address the influence of the infectious diseases on the aging process; since we are about to begin the Decade of Healthy Aging.

The dual leucine zipper kinase (DLK) alias mitogen-activated protein 3 kinase 12 (MAP3K12) has gained much attention in recent years. DLK belongs to the mixed lineage kinases, characterized by homology to serine/threonine and tyrosine kinase but exerts serine/threonine kinase activity. DLK has been implicated in many diseases including several neurodegenerative diseases, glaucoma, and diabetes mellitus. As a MAP3K, it is generally assumed that DLK becomes phosphorylated and activated by upstream signals and phosphorylates and activates itself, the downstream serine/threonine MAP2K, and ultimately MAPK. In addition, other mechanisms such as protein-protein interactions, proteasomal degradation, dephosphorylation by various phosphatases, palmitoylation, and subcellular localization have been shown to be involved in the regulation of DLK activity or its fine-tuning. In the present review, the diverse mechanisms regulating DLK activity will be summarized to provide a better insight into DLK action and possibly new targets to modulate DLK function.

For tropical forests to survive anthropogenic climate change, the trees that comprise them will need to tolerate the newly emerging conditions through adaptation or acclimation, or they can avoid climate change through range shifts and “species migrations”. In this review, we show that the rapid pace and extreme severity of modern climate change makes it extremely unlikely that tropical tree species can adapt (with some possible exceptions). We also show that while many tropical tree species are shifting their distributions to higher, cooler elevations, the rate of these migrations are mostly insufficient to offset ongoing changes in temperatures, especially in lowland tropical rainforests where thermal gradients are shallow or nonexistent. We argue that the best hope for tropical tree species to avoid becoming “committed to extinction” is acclimation. While several new methods are being developed to test for acclimation, we unfortunately still do not know if tropical tree species can acclimate or what factors may prevent or facilitate acclimation. Until these questions are answered, our ability to predict the fate of tropical species and tropical forests – and the many services that they provide to humanity – remains critically impaired.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

In the whole world, including Mexico, the rising prevalence of diabetes poses significant challenges to healthcare systems, with a notable impact on hospital admissions even being an ambulatory care sensitive condition, that means, hospital admissions are avoidable. Traditional healthcare methodologies have been instrumental in managing diabetes and preventing complications, yet they often face limitations such as merging, cleansing, and outlier analysis of health data to identify and address diseases effectively. This paper aims to address this gap by conducting a comprehensive comparison of the methodologies used in healthcare and data science for this purpose. This work uses hospital diabetes discharge records from 2010 to 2023, a total of 36,665,793 records, which belong to medical units of the Ministry of Health of Mexico. In this work, we seek to provide the arguments why as a data scientist it is mandatory to learn the field of knowledge of the problem and its implications if this is not done, and therefore to disclose insights that can help in policy decisions and reduce the burden of avoidable hospitalizations. The approach is mainly based on the standardization or adjust rates by sex and age groups. This study provides the foundations for a new way of data scientist must deal with health data.

Objective: To determine blood lead levels (BLL) in a healthy paediatric population and to analyse related sociodemographic, dietary and haematological factors. Methods: A cross-sectional study was made of 1,427 healthy subjects aged 1-16 years from the city of Almería (south-eastern Spain). BLL, iron parameters and erythropoietin were determined, and sociodemographic and dietary data obtained. The study data were analysed by multiple logistic regression. Results: The mean BLL was 1.98±1.1 µg/dl (95% CI:1.91–2.04). For 5.7% of the population, mean BLL was 2-5 µg/dl, for 2.1% it was >5 µg/dl and for 0.15% it was >10 µg/dl. Multivariate analysis showed that immigrant origin (OR:11.9; p<0.0001), low level of parental education (OR:4.6; p<0.02) and low dietary iron bioavailability (OR: 3.2; p<0.02) were all risk factors for toxic BLL. Subjects with toxic and non-toxic BLL presented similar iron and erythropoiesis-related parameters, except erythrocyte protoporphyrin, which was significantly higher in the BLL >5 µg/dl group. Conclusions: BLL and the prevalence of toxic BLL in healthy subjects aged 1-16 years living in south-eastern Spain are low and similar to those found in other developed countries. The factors associated with toxic BLL are immigrant origin, low level of parental education and dietary iron deficiency. The toxicity of BLL was not related to changes in the analytical parameters studied.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

Wrist shape varies greatly across primates and previous studies indicate that the numerous morphological differences among them are related to a complex mixture of phylogeny and function. However, little is known about whether the variation in these various anatomical differences is linked and to what extent the wrist bones vary independently. Here, we used 3D geometric morphometrics on a sample of extant hominids (Homo sapiens, Pan troglodytes, Gorilla gorilla, and Gorilla beringei), to find the model that best describes the covariation patterns among four of the eight carpals (i.e., capitate, lunate, scaphoid, and trapezium). For this purpose, 15 modular hypotheses were tested using the Covariation Coefficient. Results indicate that there is a covariation structure common to all hominids, which corresponds to stronger covariation within each carpal as compared to the covariation between carpals. However, the results also indicate that that there is a degree of codependence in the variation of some carpals, which is unique in humans, chimpanzees, and gorillas, respectively. In humans there is evidence of associated shape changes between the lunate and capitate, and between the scaphoid and trapezium. This covariation between lunate and capitate is also apparent in gorillas, while chimpanzees display the greatest disassociation among carpals, showing low covariation values in all pairwise comparisons. Our analyses indicate that carpals have an important level of variational independence which might suggest a high degree of independent evolvability in the wrists of hominids, and that although weak, the structure of associated changes of these four carpals varies across genera. To our knowledge this is the first report on the patterns of modularity between these four wrist bones in the Homininae and future studies might attempt to investigate whether the anatomical shape associations among carpals are functionally related to locomotion and manipulation.

The environmental problems generated by waste from the mining industry in the mineral extraction for business purposes are known worldwide. The aim of this work is to evaluate the microalga Muriellopsis sp. as a potential remover of metallic ions such as copper (Cu⁺²), zinc (Zn⁺²) and iron (Fe⁺²), pollutants of AMD type waters. For this, the removal of these ions was verified in artificial acid waters with high concentrations of the ions under examination. As well as, the removal was evaluated in waters obtained from areas contaminated by mining waste. The results showed that Muriellopsis sp. removed metals in waters with high concentrations after 4 to 12 hours and showed tolerance to pH between 3 to 5. These results allow proposing this species as a potential bioremediator for areas contaminated by mining activity. In this work, some potential alternatives for application in damaged areas are proposed as a decontamination plan and future prevention.

Topology optimization has become a very popular design tool when an optimum design with a concrete objective and subjected to several restrictions is searched. However, the resultant shape of the optimization process isn’t usually easy to manufacture with a typical manufacturing method as machining, being necessary an interpretation and validation of the result; besides, some parameters can be chosen, and the final shape is directly dependent on them. In this paper, a sensitivity analysis of the main parameters involved in 3D topology optimization, the penalization and the filter radius, is carried out for the concrete case of the density-based method, analyzing how manufacturable the results are for 3 axis machining. Also, a new filter and method is proposed for obtaining highly manufacturable and low interpretable parts. The main aim of the study is to help designers to choose the more appropriate parameters and showing what they must have into account for obtaining the desired optimized shapes. Note that the density-based topology optimization method has been chosen due to its popularity in commercial packages, so the conclusions may have direct applications in designers’ work. Finally, the results of the study are verified through different cases for checking the validity of the conclusions.

The macro-litter (plastic) sea bottom pollution of 14 city harbors and marinas in North Africa and in the western Baltic Sea was investigated using a new simple mobile underwater camera system. The study was complemented by a harbor manager survey and 3D-hydrodynamic transport simulations. The average pollution in German marinas was 0.1 particles/m² sea floor (0.04–1.75). The pollution in North African marinas on average was 7 times higher (0.7 particles/m²) and exceeded 3 particles/m² in city center harbors. The resulting &gt;100,000 litter particles per harbor indicate the existence of a problem. With 73%-74%, plastic particles are dominating. Existing legal and management frameworks explain the lack of plastic bottles and bags on sea floors in Germany and are one reason for the lower pollution levels. Items that indicate the role of untreated sewage water were not found. Harbor festivals seem not to be quantitatively relevant for open sea bottom pollution. Our method tends to underestimate the pollution level. Model simulations indicate that storms can cause litter reallocations and sediment cleanings. However, marina sea floor monitoring is recommendable, because it addresses pollution hot-spots, is cost-effective and takes place close to emission sources. Further, the effectiveness of land-based pollution reduction measures can easily be assessed.

Shot peening is an attractive technique for fatigue enhanced performance of metallic components, because it promotes crack initiation retardation and later crack growth. Engineering design based on fatigue crack propagation predictions applying the principles of fracture mechanics is commonly used in aluminum structures for aerospace engineering. The main purpose of present work was to analyze the effect of shot peening on the fatigue crack propagation of the 7475 aluminum alloy, under both constant amplitude loading and periodical overload blocks. The tests were performed on 4 and 8 mm thickness specimen's with stress ratios of 0.05 and 0.4. The analysis of the shot-peened surface showed a small increase of the micro-hardness values, due to the plastic deformations imposed by shot peening. The beneficial effect of surface peening on fatigue crack growth rates is quite limited to an increasing near the threshold. The specimens’ thickness has only marginal influence on the crack propagation, in opposite to the stress ratio. Periodic overload blocks of 300 cycles promotes a reduction of the fatigue crack growth rate for both intervals of 7,500 and 15,000 cycles.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

A key component for the proper functioning, availability, and reliability of power grids is the power trans- former. Although these are very reliable assets, the early detection of incipient degradation mechanisms are very important to prevent failures that may shorten their lifetime. In this work a review and comparative analysis, of classical Machine Learning algorithms (such as single and ensemble classification algorithms) and two automatic machine learning classifiers, are presented for the fault diagnosis of power transformers. The goal is to determine whether fully automated ML approaches are worse or better than traditional ML frameworks that require a human in the loop (such as a data scientist) to identify transformer faults from oil-dissolved gases data. The methodology uses a DB compiled from published and proprietary transformer fault samples. Faults data is obtained from the literature, the Duval pentagon method, and user-expert knowledge. The parameters from, either single or ensemble classifiers, were optimized through standard machine learning procedures. The results showed that the best performing algorithm is a robust automatic machine learning classifiers model followed by classical algorithms such as neural networks and stacking ensembles. These results highlight the ability of a robust automatic machine learning model for, handling imbalanced power transformers faults datasets with high accuracy, using the minimum tuning effort by the electrical experts. By providing the most probable transformer fault condition will reduce the time required to find and solve the fault.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

The addition of flaxseed and amaranth on the physicochemical, functional and microstructural changes of instant-extruded cereals was evaluated. Six different mixtures were made with additions of amaranth (30%–50%) and flaxseed (10% and 15%) using maize grits and minor additives as supplementary ingredients and then extruded in a twin-screw extruder. The extrudates evaluated, had insoluble and soluble fiber contents increased with the proportion of amaranth and flaxseed. The mixture 4 (higher flaxseed content) presented highest soluble fiber percentage (1.9%). Extruded cereals had the lowest viscosity (<99.5 cp) and highest hardness values (5.2 N) whereas the dietary fiber content was highest. Fiber content increase, resulted in a higher water solubility index (WSI) (0.5) and decrease the water absorption index (WAI) (2.5). Amaranth and flaxseed incorporation increased crystallinity, resulting in a larger, and more compact laminar structure. Amaranth and flaxseed addition resulted in extruded cereals with acceptable physicochemical and functional properties.

The aim of this work was to classify the business incubators in Spain according to the four phases of the startup’s incubation process. Considering that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the business incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis has been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors. Finally, the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3, named activity monitoring and control, was related to phase 3 or basic incubation variables. Cluster analysis facilitates the grouping of business incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small sized business incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factors 1 and 2. Factor 3, although positive, it is susceptible to improvement. They are the largest group of business incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

In this working paper we intended to address the emergence of what, potentially, will be a central concept in the very near future, Society 5.0 and that arises politically in (with) following the implementation of the concept of Industry 4.0. Society 5.0 proposes to deepen the potential of the individual-technology relationship in the promotion of the improvement of the quality of life of all people through a super smart society, is an extremely recent concept as a guiding social development that can have a profound impact in societies at all levels, such as quality of life and sustainability. It is a presentation that is based on very recent3 publications, but which also has a prospective component, which always generates some indetermination and uncertainty. Also, for this reason, it is a contribution that seeks above all else to contribute to this very urgent and necessary discussion.

Molecular dynamics(MD) simulations are playing an increasingly important role in structure-based drug discovery (SBDD). Here we review the use of MD for proteins in aqueous solvation, organic/aqueous mixed solvents (MDmix) and with small ligands, to the classic SBDD problems: binding mode and binding free energy predictions. The simulation of proteins in their condensed state reveals the solvent structure and preferential interaction sites (hot spots) on the protein surface. This information is largely transferable across all classes of protein ligands (from water to drugs) and can be used very effectively to understand ligand recognition and improve the predictive capability of well-established methods such as molecular docking. MD simulations for protein and drug or drug-like compounds are now being used but are still computationally expensive and can only be applied to specific cases. On the other hand, MDmix simulations can now be used in SBDD and we will describe the latest developments and implementations. We expect to see an increase in the application of these techniques to a plethora of protein targets to identify new drug candidates with the advent of new tools and faster computers.

CAD-CAE software companies have introduced numerous tools aimed at facilitating topology optimization through Finite Element Simulation, thereby enhancing accessibility for designers via user-friendly interfaces. However, the imposition of intricate constraint conditions or additional restrictions during calculations may introduce instability into the resultant outcomes. In this paper, an algorithm for updating the design variables called Adaptive Variable Design is proposed to keep the final design space volume of the optimized part always under the target value while giving the main algorithm multiple chances to update the optimization parameters and search for a valid design. This algorithm aims to producing results that are more conducive to manufacturability and potentially more straightforward in interpretation. A comparison between several commercial software and the proposed algorithm, implemented in MATLAB, is carried out to prove the robustness of the latter. By simulating identical parts under similar conditions, we seek to generate comparable results and underscore the advantages stemming from the adoption and comprehension of the proposed topology optimization methodology. Our findings reveal that the integrated enhancements within MATLAB pertaining to the topology optimization process yield favourable outcomes with respect to discretization, and the manufacturability of resultant geometries. Furthermore, we assert that the methodology evaluated within MATLAB holds promise for potential integration into commercial packages, thereby enhancing the efficiency of topology optimization processes.

Several studies have quantified the responses of Eucalyptus globulus plantations to weed control on its early development (2-3 years after establishment). However, long-term results of competing vegetation effects have been rarely incorporated into growth and yield models that forecast the long-term effects of reducing the intensity of competing vegetation control and its interaction with site resource availability on stem volume production close to rotation age. We compared several models predicting stand stem volume yield of Eucalyptus globulus plantations established across a water and fertility gradient growing under different intensity levels of free area of competing vegetation maintained during the first 3 years of stand development. Four sites were selected encompassing a gradient in rainfall and amount of competing vegetation. Treatments were applied at stand establishment and were monitored periodically until age 9 years. Competing vegetation control intensity levels considered 0, 5, 20, 44 and 100% weed-free cover around individual E. globulus seedlings. Maximum competing vegetation biomass production during the first growing season were 2.9, 6.5, 2.2 and 12.9 Mg ha^-1, for sites ranging from low to high annual rainfall. As expected, reductions in volume yield at age 9 years were observed as competing vegetation control intensity decreased during the first growing season. A strong relationship was established between stem volume yield loss and the intensity of competing vegetation control, the amount of competing vegetation biomass produced during the first growing season and mean annual rainfall. The slope of the relationship was different among sites and was related mainly to water and light limitations. Our results, suggest that the biomass of competing vegetation (intensity of competition) affecting site resource availability, contribute to observed long-term effects on E. globulus plantations productivity. The site with the lowest mean annual rainfall showed the highest volume yield loss at age 9 years. Sites with highest rainfall showed contrasting results related to the amount of competing vegetation biomass.

Blood biomarkers represent a promising future for studying cognitive impairment, particularly in Alzheimer's Disease (AD), as they offer a non-invasive alternative to cerebrospinal fluid tests and have potential as population screening tools. However, the relationships between these biomarkers and specific cognitive functions, as well as their utility in predicting longitudinal cognitive decline, are not yet fully understood. This descriptive review surveys the literature from 2018 to 2023, focusing on the associations between Amyloid-β, Total Tau, Phosphorylated Tau (p-tau), Neurofilament Light (Nfl), and Glial Fibrillary Acidic Protein (GFAP) with cognition. The reviewed studies are heterogeneous, varying in design and population (mixed, cognitively impaired, or unimpaired), and show results that are sometimes conflicting. Generally, cognition positively correlates with Aβ levels, especially when evaluated through the Aβ42/Aβ40 ratio. In contrast, Tau, Nfl, and GFAP levels typically show a negative correlation with cognitive performance. While p-tau measures tend to show stronger associations with cognitive functions than other biomarkers, no single blood marker has emerged as predominantly associated with a specific cognitive domain. These findings add to our understanding of the complex relationship between blood biomarkers and cognitive performance and underscore their potential utility in clinical evaluations of cognition.

The use of new assistive technologies in general, and Socially Assistive Robots (SAR) in particular is becoming increasingly common for supporting people’s health and well-being. However, it still faces many issues regarding long-term adherence, acceptability and utility. Most of these issues are due to design processes that insufficiently take into account the needs, preferences and values of intended users. Other issues are related to the currently very limited amount of long-term evaluations, performed in real world settings, for SAR. This study presents the results of two regional projects that consider as a starting hypothesis that the assessment in controlled environments and/or with short exposures may not be enough in the design of a SAR deployed in a retirement home and the necessity of designing for and with users. Thus, the proposed methodology has focused in use cases definitions that follow a human-centred and participatory design approach. The main goals have been facilitating system acceptance and attachment by involving stakeholders in the robots design and evaluation, overcoming usage barriers and considering user’s needs integration. The implementation of the first use case deployed and the two-phase pilot test performed in the retirement home are presented. In particular, a detailed description of the interface re-design process based on improving a basic prototype with users’ feedback and recommendations is presented together with main results of a formal evaluation that has highlighted the impact of changes and improvements addressed in the first redesign loop of the system.

Accurate transfer learning of clinical outcomes, e.g., of the effects and side effects of drugs or other interventions, from one cellular context to another (in-vitro versus ex-vivo versus in-vivo, or across tissues), between cell-types, developmental stages, omics modalities or species, is considered tremendously useful. Ultimately, it may avoid most drug development failing in translation, despite large investments in the preclinical stages, which includes animal experiments requiring careful justification. Thus, when transferring a prediction task from a source (model) domain to a target domain, what counts is the high quality of the predictions in the target domain, requiring molecular states or processes common to both source and target that can be learned by the predictor, reflected by latent variables. These latent variables may form a compendium of knowledge that is learned in the source, to enable predictions in the target; usually, there are few, if any, labeled target training samples to learn from. Transductive learning then refers to the learning of the predictor in the source domain, transferring its outcome label calculations to the target domain, considering the same task. Inductive learning considers cases where the target predictor is performing a different yet related task as compared to the source predictor, making some labeled target data necessary. Often, there is also a need to first map the variables in the input/feature spaces (e.g. of gene names to orthologs) and/or the variables in the output/outcome spaces (e.g. by matching of labels). Transfer across omics modalities also requires that the molecular information flow connecting these modalities is sufficiently conserved. Only one of the methods for transfer learning we reviewed offers an assessment of input data, suggesting that transfer learning is unreliable in certain cases. Moreover, source domains feature their very own particularities, and transfer learning should consider these, e.g., as differences in pharmacokinetics, drug clearance or the microenvironment. In light of these general considerations, we here discuss and juxtapose various recent transfer learning approaches, specifically designed (or at least adaptable) to predict clinical (human in-vivo) outcomes based on molecular data, towards finding the right tool for a given task, and paving the way for a comprehensive and systematic comparison of the suitability and accuracy of transfer learning of clinical outcomes.

Taking into account the increase in the emission of greenhouse gases produced by ships, during navigation and maneuvering in the port, a direct consequence of the increase in maritime traffic, the international community has developed a broad set of regulations to limit such emissions. The installation in commercial ports of automatic mooring systems by means of vacuum suction cups (AMS), thus reducing considerably the time required to carry out the mooring and unmooring maneuvers of ships, is a factor that is considerably influencing the decrease in Emissions of polluting gases in commercial ports with high traffic. The objective of the present work is to verify the influence of the use of the AMS on the emissions of polluting gases produced in the facilities destined to the traffic of container ships. It examines the CO2 emissions of container ships that call in the only three container ports equipped with AMS: Salalah (Oman), Beirut (Lebanon) and Ngqura (South Africa). Between them, these three ports supported the transit of 6 million TEUS in 2017. The calculation of emissions is made taking into account the time saved when performing the mooring maneuvers using the new AMS system compared with when it is not used. To do this, two different calculation methods are used: EPA and ENTEC to then compare the results of the two and thus obtain the reduction in emissions per TEU in these terminals during the mooring maneuvers. The paper concludes with a discussion on the values of the reductions in emissions obtained and the advantages of the installation of AMS in commercial ports located near population centres.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

The carbapenemase OXA-244 is a derivate of OXA-48, and its detection is very difficult in laboratories. Here we report the identification and genomic analysis of an Escherichia coli isolate (28Eco12) harbouring the bla_OXA-244 gene identified in Colombia, South America. The 28Eco12 isolate was identified during a retrospective study and it was recovered from a patient treated in Colombia. The complete nucleotide sequence was established using the PacBio platform. A comparative genomics analysis with other bla_OXA-244–harbouring Escherichia coli strains was performed. The 28Eco12 isolate belonged to sequence type (ST) 38 and its genome was composed of two molecules, a chromosome of 5,343,367 bp and a plasmid of 92,027 bp, which belonged to the incompatibility group IncY and did not harbour resistance genes. The bla_OXA-244 gene was chromosomally-encoded and mobilized by an ISR1-related Tn6237 composite transposon. Notably, this transposon was inserted and located within a new genomic island. For our knowledge this is the first report of a bla_OXA-244–harbouring Escherichia coli isolate in American continent.Our results suggest that the introduction of the OXA-244-producing E. coli isolate was through clonal expansion of the ST38 pandemic clone. Other isolates producing OXA-244 could be circulating silently on the American continent.

Posttraumatic stress disorder (PTSD) and/or specific PTSD symptoms may evoke disordered eating and unhealthy lifestyles, resulting in adverse cardiometabolic events (e.g., hypertension and obesity) in certain groups, which may implicate the treatment of this complex condition. The diagnostic criteria of PTSD have lately expanded beyond the three common symptoms (intrusion, avoidance, and hyperarousal). Simultaneously, four-, five-, and six-dimensional structures of the Impact of Event Scale-Revised (IES-R), a popular PTSD measure, seem to be more robust than the original three-dimension structure. Within the context of COVID-19, this instrumental study used a convenience sample of 58 dental healthcare workers (HCWs) from Russia (mean age = 44.1±12.2 years, 82.8% females) to examine the criterion and predictive validity of two IES-R structures: the IES-R3 and the IES-R6 (with the added symptoms of numbing, sleep disturbance, and irritability). The subscales of the two IES-R structures expressed good internal consistency, strong correlations with the PTSD Symptom Scale (PSS), hypertension diagnosis, and high body mass index (BMI). In receiver-operating characteristic (ROC) curve analysis, all IES-R models perfectly predicted the PSS (all area under the curve (AUC) >0.9, p values <0.001). The IES-R, both hyperarousal subscales, and the IES-R3 intrusion subscale significantly predicted high BMI. Both avoidance subscales and the IES-R3 intrusion subscale, not the IES-R, significantly predicted hypertension. In conclusion, both IES-R structures can reliably measure PTSD symptoms. The IES-R, hyperarousal, and intrusion may be credible criterion variables for predicting high BMI within PTSD while the intrusion and avoidance subscales may reflect the cardiovascular consequences associated with PTSD more reliably than the IES-R itself. The IES-R subscales may predict cardiometabolic adversities in PTSD, signifying a need for proper assessment of lifestyle and the application of dietary and exercise interventions in order to lower physical morbidity in PTSD. Replicating the study in larger samples, which comprise different physical and mental conditions from heterogenous cultural contexts is pivotal to validate the results (e.g., in specific groups such as those with confirmed traumatic exposure and comorbid mood dysfunction).

Dysregulation of the arsenal of cells, growth factors, cytokines, proteases, and proteins involved in wound healing (WH), could delay the healing process. Plants and plant-derived molecules (PDMs) have been used as medicines for skin wounds. This study aimed to select and evaluate the pro-healing capacity of PMDs. Thirty-three PDMs and 10 therapeutic targets (TTs) were chosen for molecular docking and PDMs: aristolochic acid (AA), α-copaene, selinenes, β-caryophyllene (BC), and BCoxide, and TTs: metalloproteinase (MMP) 3, MMP13, and tumor necrosis factor (TNF α) for molecular dynamics. The bests inhibitor was AA, but because of its toxicity, BC and BCoxide were chosen for evaluation in HaCat cells and BALB/c mice excisional model. Both compounds were not toxic, and higher percentages of lesion area closure (LAC) were induced by BC treatment (p<0.05). All mice healed; however, an initial delay of LAC was induced by 0.05, 0.1% BCoxide, 0.1% BC, and allantoin. At the end of treatment, lower numbers of mast cells, level of cellular infiltrates (except 1% BCoxide and 0.05, 0.5%BC), epidermal thickness tendency (except 0.1, 0.5% BCoxide), and higher values of SC-thickness, and collagen fibers only by 0.5% BC treatment compared with untreated control (p<0.05) were observed. Our results show that BC is a promising multitarget candidate for wound healing treatment and optimization campaigns.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

Cancer is a disease that encompasses multiple and different malignant conditions and is among the leading causes of death in the world. Therefore, the search for new pharmacotherapeutic options and potential candidates that can be used as treatments or adjuvants to control this disease is urgent. Natural products, especially those obtained from plants, have played an important role as a source of specialized metabolites with recognized pharmacological properties against cancer, therefore, they are an excellent alternative to be used. The objective of this research was to evaluate the action of the monoterpene isoespintanol (ISO) against the human tumor cell lines MDA-MB-231, A549, DU145, A2780, A2780-cis and the non-tumor line MRC-5. Experiments with MTT and fluorescence with propidium iodide (PI), DAPI and green plasma revealed the cytotoxicity of ISO against these cells; furthermore, morphological and chromogenic studies revealed the action of ISO on cell morphology and the inhibitory capacity on reproductive viability to form colonies in MDA-MB-231 cells. Likewise, 3D experiments validated the damage in these cells caused by this monoterpene. These results serve as a basis for progress in studies of the mechanisms of action of these compounds and the development of derivatives or synthetic analogues with a better antitumor profile.

5-Hydroxytryptamine (5-HT) or serotonin plays a crucial role as a neuromodulator and/or neurotransmitter of several nervous system functions. Its actions are complex and depend on multiple factors, including the type of effector or receptor activated. Briefly, 5-HT can activate: (i) metabotropic (G-protein-coupled) receptors to promote inhibition (5-HT1, 5-HT5) or activation (5-HT4, 5-HT6, 5 HT7) of adenylate cyclase, as well as activation (5-HT2) of phospholipase C; and (ii) ionotropic receptors (5-HT3), which form a ligand-gated Na+/K+ channel. Regarding blood pressure regulation (and beyond the intricacy of central 5-HT effects), this monoamine also exerts direct postjunctional (on vascular smooth muscle and endothelium) or indirect prejunctional (on autonomic and sensory perivascular nerves) effects. At the prejunctional level, 5-HT can facilitate or preclude the release of autonomic (e.g., noradrenaline and acetylcholine) or sensory (e.g., calcitonin gene-related peptide) neurotransmitters facilitating hypertensive or hypotensive effects. Hence, we cannot formulate a specific impact of 5-HT on blood pressure level, since an increase or decrease in neurotransmitter release would be favoured depending on the type of prejunctional receptor involved. This review summarizes and discusses the current knowledge on the prejunctional mechanisms involved in blood pressure regulation by 5-HT and its impact on some vascular-related diseases.

Canistel (Pouteria campechiana (Kunth) Baehni) (yellow sapote, canistel). Originally from Mexico, the fruit is edible, and the tree is used as an ornamental and medicinal plant. Descriptive studies were carried out with the objective of morphologically characterizing the fruits and leaves of trees located in different regions of Mexico to select outstanding specimens and propose their massive reproduction. The trees were selected in three zones. In zone 2 from flower anthesis to harvest 11 months, fruits with 3 seeds, greater weight (180 to 330 g) and quantity of pulp (198.88 g), subglobose shape, total soluble solids 33 %. The fruits of zone 1 at harvest 8 months and zone 3 took 9 months to be harvested, in the rest of the characteristics evaluated were exceeded by the fruits of zone 2. To characterize the canistel (P. campechiana) leaf and identify accessions or cultivars, the three main variables, according to the principal component analysis were: leaf area, perimeter, and minor diameter. The three zones where canistel fruits and leaves were characterized are important and can be recommended for propagation in zones with favorable climatic conditions for fruiting in tropical and subtropical regions of Mexico.