Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Glypicans are a family of heparan sulfate proteoglycans that are attached to the outer plasma membrane leaflet of the producing cell by a glycosylphosphatidylinositol anchor. Glypicans are involved in the regulation of many signalling pathways, including those that regulate the activities of Wnts, Hedgehog (Hh), Fibroblast Growth Factors (FGFs) and Bone Morphogenetic Proteins (BMPs), among others. In the Hh signalling pathway, glypicans have been shown to be essential for ligand transport and the formation of Hh gradients over long distances, for the maintenance of Hh levels in the extracellular matrix and for its unimpaired reception in distant recipient cells. Recently, two mechanistic models have been proposed to explain how Hh can form the signalling gradient and how glypicans may contribute to it. In this review, we describe the structure, biochemistry and metabolism of glypicans and their interactions with different components of the Hh signalling pathway that are important for the release, transport and reception of Hh.

This paper uses the numerical results of surveys sent to Huelva’s (Andalusia, Spain) households to determine the degree of knowledge they have about the urban water cycle, needs, values, and attitudes regarding water in an intermediary city with low water stress. In previous research, we achieved three different households’ clusters. The first one grouped households with high knowledge of the integral water cycle and a positive attitude to smart devices at home. The second cluster described households with low knowledge of the integral water cycle and high sensitivity to price. The third one showed average knowledge and predisposition to have a closer relationship with the water company. This paper continues with this research line, applying Classification and Regression Trees (CART) to determine which hierarchy of variables/factors/ independent components obtained from the surveys are the decisive ones to predict the range of household water consumption in Huelva. Positive attitudes towards improved cleaning habits for personal or household purposes are the highest hierarchy component to predict the water consumption range. Second in the hierarchy, the variable Knowledge Global Score about the integral urban water cycle, associated with water literacy, also contributes to predicting the water consumption range. Together with the three clusters obtained previously, these results will allow us to design water demand management strategies (WDM) fit for purpose that enable Huelva’s households to use water more efficiently.

This article shows the numerical results and the analysis of households' degree of knowledge in an intermediary city such as Huelva (Andalusia, Spain) about the sustainable use of urban water. It analyzes the needs and values regarding water and the attitudes that households maintain regarding the acceptance of reclaimed water and the use of new technologies to achieve more efficient and sustainable consumption. These results are part of the stages of needfinding and synthesis of Design Thinking methodology, adopted as a framework to improve the efficiency and sustainability of urban water among households in this city. Different statistical analysis techniques of surveys sent to households and the use of clustering are the mathematical tools used to draw conclusions and recommendations that allow the design of a web-based prototype grounded on Product Service Systems methodology, as a tool to improve the engagement of households concerning water and align citizens with the sustainability of their city. Strategies of customization and technological facilitators will be the means to improve the hydrosocial contract among households in Huelva in future later stages of the project.

The cultivation of pea pods spans across various regions and climates with a global production of around 20 million tons. The pea peel wastes, which make up 30–40% of the total weight of the peas, are freely available in large quantities. The biomass used was characterized via ultimate, proximate, and structural analysis obtaining a 20,2 %w of cellulose and 17,4 %w of hemicellulose which via valorization processes can be transformed into platform chemicals. Hydrothermal valorization presents itself as a clean form of treatment of said wastes, ranging from 120 – 180 ºC (LHW) to 180 to 260 ºC (HTC). The use of LHW can lead to the production of sugars (up to 70%w yield) and levulinic acid (4 %w yield) while the use of HTC leads to Formic acid (40 %w) and levulinic acid (4 %w yield). The use of LHW for longer times favors the production of HMF and Furfural. The use of homogeneous catalysts (H2SO4, CH3COOH, KOH and NaHCO3) was implemented and their selectivity described. Solid fractions of LHW and HTC were characterized via FTIR and elemental analysis and the change in their structure described as they shift from biomass to biochar. Optimal conditions for each platform chemical were reported for best utilization of the peapod waste.

Helicobacter pylori cytotoxin-associated gene A protein (CagA) has been associated with the increase in virulence and risk of cancer. It has been demonstrated that CagA's translocation is dependent on its interaction with phosphatidylserine. We evaluated the variability of the N-terminal CagA in 127 sequences reported in NCBI, by referring to molecular interaction forces with the Phosphatidylserine and the docking of 3 mutations chosen from variations in specific positions. The major sites of conservation of the residues involved in CagA-Phosphatidylserine interaction were 617, 621 and 626 which had no amino acid variation. Position 636 had the lowest conservation score, so mutations in this position were evaluated to observe the differences in intermolecular forces of the CagA-Phosphatidylserine complex. We evaluated the docking of 3 mutations: K636A, K636R and K636N. The models of the crystal and mutations presented a ΔG of −8.919907, −8.665261, −8.701923, −8.515097 Kcal/mol, respectively, while mutations K636A, K636R, K636N and the crystal structure presented 0, 3, 4 and 1 H-bonds, respectively. Likewise, the bulk effect of the ΔG and amount of H-bonds was estimated in all of the docking models. The type of mutation affected both the ΔG (χ²(1) = 93.82, p-value < 2.2 × 10⁻¹⁶) and the H-bonds (χ²(1) = 91.93, p-value < 2.2 × 10⁻¹⁶). In all the data, 76.9% of the strains that exhibit the K636N mutation produced a severe pathology. The average H-bond count diminished when comparing the mutations with the crystal structure of all the docking models, which means that other molecular forces are involved in the CagA-Phosphatidylserine complex interaction.

Sugarcane (Saccharum spp.) is a crop of great industrial and alimentary importance, essential for the production of numerous products. Given its significance, genetic improvement programs exist that involve a rigorous study process, from material selection to the development of new varieties, requiring at least seven selection phases. This study modeled the growth curve of the sucrose percentage (SP) in 33 hybrids and six control varieties (MEX 69-290, ITV 92-1424, CP 72-2086, COLMEX 94-8, COLMEX 95-27, RB 85-5113) during the plant and ratoon periods in the experimental fields of the Melchor Ocampo Sugar Mill, Jalisco, Mexico. For clustering the materials, k-means, k-medoids, and Density-based spatial clustering of applications with noise (DBSCAN) algorithms were used, considering four maturity types among the control varieties. The DBSCAN algorithm proved to be the most effective, as the means between groups were not statistically equal. The hybrids identified as candidates for subsequent phases due to their high SP were COSTA JAL, ATEMEX 99-48, ATEMEX 99-1, ATEMEX 99-61, MEX 70-486, MEX 80-1521, ITSAMEX 07-44814, ITSAMEX 06-6395, and ITSAMEX 07-1903. These results are crucial for improving the productivity and sustainability of the crop, with significant implications for the sugar industry.

Currently, there are different types of technology for the production of electricity that use various energy sources, this causes the establishment of generation centers that provide from a small amount to tens of megawatts of electrical energy. These centers are built to supply electricity to nearby loads through networks integrated into a large electrical system or in isolation with their electrical system. The technological evolution, the different energy sources, and the generation centers close to the consumers entail what has been called a distributed generation (DG), the DG carries with it aspects that need to be analyzed. In this paper, the impact of wind generation on the medium voltage energy distribution network is studied, it was determined that the addition to the distribution network of power by wind turbines less than the transmission center does not produce an impact on the network. Simulated results obtained using SIMULINK and DIgSILENT are presented and discussed.

This document summarizes the evidence currently available about the effects of the anesthetic agents and techniques used in primary cancer surgery and long-term oncologic outcomes, and the biomolecular mechanisms involved in their interaction..

(1) Background: Ultra-endurance exercise involves a high physical impact, resulting in muscle damage, inflammatory response and production of free radicals that alter the body's oxidative state. Supplementation with antioxidants, such as beetroot, may improve recovery in ultra-endurance runners. The aim of this study was to determine whether there is a correlation between the beetroot intake and the recovery of serum oxidative status, inflammatory response and muscle damage parameters after an ultra-endurance race. (2) Methods: An observational and longitudinal study was conducted by means of surveys and blood samples collected from 32 runners during the IX Penyagolosa Trails CSP® race and the two following days. The variables C-reactive protein (CRP), lactate dehydrogenase (LDH), creatine kinase (CK), the activity of the antioxidant enzymes glutathione peroxidase (GPx) and glutathione reductase (GR), as well as the oxidative damage markers malondialdehyde (MDA), carbonyl groups (CG) and loss of muscle strength using the Squat Jump test (SJ) were analyzed to discriminate whether beetroot consumption can modulate the recovery of ultra-trail runners. (3) Results: Significant differences were observed between runners who ingested beetroot and those who did not, in terms of oxidative status, specifically in serum GPx activity at 24 and 48 hours, muscle damage variables CK and LDH and in SJ test at the finish line. Therefore, the intake of supplements containing beetroot positively influences the recovery of serum oxidative status and muscle damage after ultra-endurance running.

The aim of this study was to evaluate the intensity of the annual sexual behavior (SB) of Boer bucks under tropical conditions in southern Mexico. For one year, 16 extensively grazing males were evaluated for SB individually with estrogenized goats. From the beginning of the experiment and every 30 days, body weight (BW), body condition (BC), testicular circumference (TC), odor intensity (OI) and SB (nudging, ano-genital sniffing, flehmen, mounting attempts, mounts with intromission, and self-urination) were recorded. The bucks showed a more intense SB during the months of November to May than during the months of June to October (p < 0.05). Greater frequency was found for nudging, ano-genital sniffing, mounting attempts, and self-urination in the months of November to May (p < 0.001). BW was lower during the months of January to August than in the months of September to December (p < 0.05). On the other hand, TC increased from October to December (p < 0.05). Similarly, the OI in males varied over time (time effect; p < 0.001). In fact, an increased odor was found from October to December. The conclusions were that breed male goats from the tropics of Guerrero have a more intense SB during the months of November to May, which corresponds to the time of the year when forage availability is the greatest.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

Obesity is a risk factor for the development of gestational diabetes mellitus (GDM). However, the most optimal type of nutritional intervention to prevent GDM in high-risk women is not clearly defined. This study investigates if nutritional treatment based on the Mediterranean diet (MedDiet) before 12th gestational week (GW) in women at high risk due to a body mass index (BMI)≥25kg/m2, reduces the rate of GDM and metabolic syndrome (MetS) at 3 years postpartum. We performed a post-hoc analysis of the San Carlos Gestational Prevention Study. A total of 735 women with BMI≥25kg/m2 were evaluated between 2015-2018, 246 in standard diet control group (CG) and 489 in MedDiet intervention group (IG). The rate of GDM was significantly lower in IG compared to CG (25.1%vs31.7%;p=0.037). Postnatal follow-up was completed by 141 women in CG (57%) and 312 women in IG (64%). At 3 years postpartum, we observed a reduction (relative risk 95% confidence interval) in the rates of impaired fasting glucose (IFG) (0.51 (0.28-0.92);p=0.019), obesity (0.51 (0.28-0.92),p=0.041), waist circumference (WC)≥89.5cm (0.54 (0.31-0.94);p=0.022) and MetS (0.56 (0.33-0.94);p=0.003). MedDiet reduces the rate of GDM and postpartum MetS in women with BMI)≥25kg/m2, suggesting that its implementation should be routinely recommended from the first GWs.

Capirona (Calycophyllum spruceanum Benth.) belongs to subfamily Ixoroideae, one of de major lineages in the Rubiaceae family, and is an important timber tree, with origin in the Amazon Basin and has widespread distribution in Bolivia, Peru, Colombia, and Brazil. In this study, we obtained the first complete chloroplast (cp) genome of capirona from department of Madre de Dios located in the Peruvian Amazon. High-quality genomic DNA was used to construct librar-ies. Pair-end clean reads were obtained by PE 150 library and the Illumina HiSeq 2500 platform. The complete cp genome of C. spruceanum has a 154,480 bp in length with typical quadripartite structure, containing a large single copy (LSC) region (84,813 bp) and a small single-copy (SSC) region (18,101 bp), separated by two inverted repeat (IR) regions (25,783 bp). The annotation of C. spruceanum cp genome predicted 87 protein-coding genes (CDS), 8 ribosomal RNA (rRNA) genes, 37 transfer RNA (tRNA) genes and 01 pseudogene. A total of 41 simple sequence repeats (SSR) of this cp genome were divided into mononucleotides (29), dinucleotides (5), trinucleotides (3), and tetranucleotide (4). Most of these repeats were distributed in the noncoding regions. Whole chloroplast genome comparison with the other six Ixoroideae species revealed that the small single copy and large single copy regions showed more divergence than invert regions. Finally, phylogenetic analysis resolved that C. spruceanum is a sister species to Emmenopterys henryi, and confirms its position within the subfamily Ixoroideae. This study reports for the first time the genome organization, gene content, and structural features of the chloroplast genome of C. spruceanum, providing valuable information for genetic and evolutionary studies in the genus Calycophyllum and beyond.

There are currently around 78 Nuclear Power Plants (NPP) in the world based on Boiling Water Reactors (BWR). The current parameter to assess BWR instability issues is the linear Decay Ratio (DR). However, it is well known that BWRs are complex non-linear dynamical systems that may even exhibit chaotic dynamics that normally preclude the use of the DR when the BWR is working at a specific operating point during instability. In this work a novel methodology based on an adaptive Shannon Entropy estimator and on Noise Assisted Empirical Mode Decomposition variants is presented. This methodology was developed for real-time implementation of a stability monitor. This methodology was applied to a set of signals stemming from several NPPs reactors (Ringhals-Sweden, Forsmark-Sweden and Laguna Verde-Mexico) under commercial operating conditions, that experienced instabilities events, each one of a different nature

The quest for youthful, healthy skin and full, vibrant hair has long been a driving force in the dermocosmetics field. However, traditional approaches often struggle to address the underlying causes of aging, damage, and hair loss. Regenerative cosmetics, powered by skin tissue engineering, offer a transformative alternative. This review explores the emerging field of using engineered skin tissues for cosmetic purposes, focusing specifically on their potential for anti-aging, repair, and hair restoration applications. We discuss how these technologies aim to rejuvenate aging skin by promoting collagen production, reducing wrinkles, and improving overall skin function. Additionally, the use of engineered skin for wound healing and scar reduction is examined, highlighting their potential to improve the appearance and functionality of damaged skin. Finally, we advance the exciting prospects of utilizing skin tissue engineering techniques to regenerate hair follicles, potentially offering solutions for hair loss and promoting denser hair growth.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

In December 2019, the novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) emerged in the province of Wuhan, China. Since then, it has spread worldwide with new mutations being reported. We performed genomic analysis to identify the changes in genetic diversity of SARS-CoV-2 between December 2019 and November 2020, and through molecular surveillance, we monitored the mutations that could be involved in viral fitness. We analyzed 2,213 complete genomes from 6 geographical regions worldwide, which were downloaded from GenBank and GISAID databases. Although SARS-CoV-2 presented low genetic diversity, there has been an increase over time, with the presence of several hotspot mutations throughout its genome. We identified 7 frequent mutations that resulted in non-synonymous substitutions (dN). Two of them, C14408T>P323L and A23403G>D614G, located in the nsp12 and Spike protein, respectively, emerged early in the pandemic and showed a considerable increase in frequency over time. Two other mutations, A1163T>I120F in nsp2 and G22992A>S477N in the Spike protein emerged recently and have spread in Oceania and Europe. Continuous molecular surveillance of SARS-CoV-2 will be necessary to detect and describe the transmission dynamics of new variants of the virus with clinical relevance. This information is important to improve programs to control the virus.

The integration of Industry 4.0 technologies in photovoltaic (PV) installations offers significant potential to enhance efficiency, reliability, and economic viability. This study evaluates the technical and economic impacts of implementing the Internet of Things (IoT), artificial intelligence (AI), and advanced data analytics in PV systems within the residential and industrial sectors in the Region of Murcia. Real-time monitoring technologies based on IoT sensors were analyzed to collect data on the operational performance of pilot PV installations. Advanced data analysis techniques, including machine learning, were analyzed to process the collected data, enabling predictive maintenance, performance optimization, and future production estimation. The study also explored the use of drones and computer vision for automated inspection of solar panels, identifying issues such as hotspots and dirt accumulation. The results demonstrate significant improvements in energy efficiency, system availability, and reduction of failures and downtime. Economic analyses indicate cost savings in operation and maintenance and increased overall system reliability. This research identifies key barriers and opportunities for adopting 4.0 technologies in the PV sector and proposes strategies to overcome challenges and leverage benefits. The findings contribute to the advancement of knowledge and the promotion of sustainable and efficient energy systems in the solar industry.

The generation of platform chemicals and hydrochar is of great interest because they reduce dependence on fossil resources and contribute to climate change mitigation by reducing carbon emissions. The main objective of this study was to evaluate the effect of biomass particle size and biomass water ratio in a hydrothermal conversion system for the generation of value-added products obtained from sugarcane bagasse. Biomass characterization was performed using proximal, elemental, and structural analysis; hydrothermal carbonization was carried out at 220 to 260 °C for one hour; and conversion was monitored using pH, conductivity, and IR spectroscopy. Platform chemicals were quantified by HPLC-IR. Hydrochars were characterized by scanning electron microscopy and energy dispersive spectroscopy. The results show that with a biomass:water ratio of 1:50 and a particle size of 212 μm at 220 °C, a yield of 31.07 % of platform chemicals was obtained on a dry basis. Likewise, the hydrochar with the highest carbon content and a higher porosity appearance was obtained with a biomass-to-water ratio of 1:50 and a particle size of 600 μm at 260 °C.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

Sweet cucumber (Solanum muricatum) sect. Basarthrum, is a neglected horticultural crop native of the Andean region. It is naturally distributed very close to potatoes (Solanum sect. Petota) and tomatoes (Solanum sect. Lycopersicon), two groups of high economic importance. To date, molecular tools for this crop are still undetermined. We here obtained the first complete chloroplast (cp) genome of sweet cucumber and compared with seven Solanaceae species. Pair-end clean reads were obtained by PE 150 library and the Illumina HiSeq 2500 platform. The complete cp genome of S. muricatum had a 155,681 bp with typical quadripartite structure, containing a large single copy (LSC) region (86,182 bp) and a small single-copy (SSC) region (18,360 bp), separated by two inverted repeat (IR) regions (25,568 bp). The annotation of chloroplast genome predicted 88 protein-coding genes (CDS), 8 ribosomal RNA (rRNA) genes, 37 transfer RNA (tRNA) genes, and one pseudogene. A total of 48 perfect microsatellites were identified, divided in mononucleotide repeats (32), followed by tetranucleotide (6) and dinucleotides (5). SSRs with trinucleotides repeats (3), pentanucleotide (1) and hexanucleotide (1) repeats motifs in these genomes were identified in lower quantity. Most of these repeats were distributed in the noncoding regions. Whole chloroplast genome comparison with the other seven Solanaceae species revealed that the small and large single copy regions showed more divergence than inverted regions. Finally, phylogenetic analysis resolved that S. muricatum is a sister species to members of sections Petota + Lycopersicum + Etuberosum. This study reports for the first time the genome organization, gene content, and structural features of the cp genome of S. muricatum. Also, this study may provide the basis for evaluating genetic diversity within Solanum, and will be useful to examine the evolutionary processes in sweet cucumber landraces.

The stellar winds of the central stars of planetary nebulae play an essential role in planetary nebulae shaping. In the interacting stellar winds model, the fast stellar wind injects energy and momentum which are transfered to the nebular envelope through an X-ray-emitting hot bubble. Together with other physical processes, such as the ionization of the nebular envelope, the asymmetrical mass-loss in the AGB, and the action of collimated outflows and magnetic fields, the presurized hot gas determines the expansion and evolution of planetary nebulae. \emph{Chandra} and \emph{XMM-Newton} have provided us with detailed information of this hot gas. Here in this talk I will review our current understanding of the effects of the fast stellar wind in the shaping and evolution of planetary nebulae and give some hints of the promissing future of this research.

This paper presents a novel improvement of MuSIASEM (Multiscale Integrated Analysis of the Societal and Ecological Metabolism) by incorporating a new regional analysis of the electricity metabolism across levels. An analysis of Mexico illustrates this toolkit and shows that the industry sector had Economic Energy Intensity (EEI) with 40.3 MWh/MMXN reached a higher value than the commerce and services sector with 0.84 MWh/MMXN. Regarding the Economic Labor Productivity (ELP) indicator (AV/h), the industrial sector with 208.5 TMXN/Kh reached a higher value than the Commercial and services sector with 114.3 TMXN/Kh. With reference to the Exosomatic Metabolic Rate (EMR), the Household sector obtained 59.3 KWh/Kh whereas the paid sector reached 2,486.4 KWh/Kh. Disaggregation of the EMR indicator into economic sectors shows that the Industrial sector obtained 8.4 KWh/Kh and the commercial and services sector reached 0.10 KWh/Kh. The lack of complete data for the agricultural sector does not allow us to calculate EEI, ELP, and EMR indicators accurately. Considering the analysis of indicators by regions, regarding the EEI rate, the Central region had the lowest value with 12.7 MWh/MMXN, followed by the Northeast with 21.4 MWh/MMXN and Western with 29.4 MWh/ MMXN, which means that they require less electricity to produce more added value. In terms of the ELP indicator, it was found regions with higher values were Northeast with 182.3 MMXN/Mh, Central with 177.5 MMXN/Mh, and North with 127 MMXN/Mh, which means that these regions produce more added value per hour of work. About the EMR, it is observed that regions in the northern part of the country had higher values: Northwest with 337 KWh/Kh, Baja California Sur with 334 KWh/Kh, Baja California with 328 KWh/Kh, North with 313 KWh/Kh and Northeast with 274 KWh/Kh, which means that these regions consume more electricity per hour. This innovative approach is useful for governance because it helps to understand and reduce asymmetries across regions, resulting in more social equality and a better economic equilibrium across sectors and regions.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

The aim of this article has been to evaluate the impact of a physical-sport education programme, based on the pedagogical model of Sport Education within the framework of quality Physical Education and approached from the field of social and emotional learning, on a set of psychological variables: subjective well-being (quality of life related to health, positive affect and negative affect); trait emotional intelligence and social anxiety. A total number of 113 Compulsory Secondary Education students were involved, aged 12 to 15 years old, 44 of whom belonged to the control group (CG) and 69 to the experimental group (EG). A quasiexperimental design of repeated pretest and posttest measures with the CG was used. The results obtained in this investigation revealed that the intervention programme caused significant improvements in the subjective well-being and the trait emotional intelligence for the EG. These findings reinforce the pedagogical efficiency of the programme with regards to the aim that has been set. Likewise, the findings also highlight the suitability and appropriateness in terms of innovative teaching proposals. In the same way, the results showed relevant empirical contributions in this given school context due to its psychological benefits and the encouragement of healthy living.

This work reports the isolation, purification, and anti-inflammatory evaluation of compounds from the plant species Ageratina pichinchesis. Using open-column chromatography, 11 known compounds were purified, whose chemical structures were elucidated by nuclear magnetic resonance techniques (1D and 2D). All compounds were evaluated in the in vitro model of RAW 264.7 mouse macrophage cells measuring nitric oxide inhibition as a determination of the anti-inflammatory effect. Outstandingly, the compound betuletol 3-O-β-glucoside (11) exhibited inhibition of nitric oxide with an IC50 of 75.08 ± 3.07% at 75 µM, additionally, it inhibited the secretion of interleukin 6 (IL-6) and activation of nuclear factor (NF-kβ). These results show that compound 11 could be considered as a potential anti-inflammatory agent in suppressing the expression of NF-kβ target genes such as the proinflammatory pathway and inducible nitric oxide synthase (iNOS). Consequently, the medicinal use attributed in traditional medicine to the A. pichinchensis species is due to the diversity of compounds that the plant biosynthesizes, demonstrating that its effect relates to anti-inflammatory effects associated with compound 11.

This paper deals with the analysis of the cognitive functions of the cerebral cortex or cortex in the evolutionary context. The triune brain model is presented given its notorious popularity in fields that are not strictly neuroscientific, and its limitations and inaccuracies are also shown. Although it is an outdated theory, this one represented the passage to a new era, because it really was the model of the movement towards understanding the brain in evolutionary terms. Next, the paper illustrates the different areas of the cortex and their functions, as well as the evolution of the brain and the cortex in vertebrates. To date, the expansion of the cortex with the amniotes was placed 300 million years ago, although recent studies place it in the lampreys more than 500 million years ago. Evolutionary changes in mammalian brain and cortex size are discussed, showing the evolution from three to six cell layers and trends in different groups of mammals. Finally, the most recent contributions in the field of research are illustrated, such as the role of neurogenesis and the evolution of the connectivity of the cortex.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

Objective: To identify risk factors(RF) related to abnormal glucose regulation(AGR) 3 years postpartum according to 3-month-postpartum glucose status. Research design: Normoglycemic pregnant women of the St. Carlos Gestational Study included before gestational week 12, during 2015-2017. Of 3,036 eligible women, 2529 were followed-up until delivery: 1400 participated in postpartum follow-up. AGR defined as fasting serum glucose (FSG)>5.6 mmol/L and/or HbA1c >5.7% (39 mmol/mol) and/or 2h-SG ≥140/mg/dL after 75-g OGTT. 12-modifiable and 3-unmodifiable RF were analyzed for associations with glycemic changes. Reinforcement of Mediterranean Diet adherence was provided to all women at the postpartum visit by a dietitian Results: 137/1400(9.8%) women presented AGR 3 years postpartum, 27/137(19.7%) also had at 3 months, whereas 110/137(80.2%) had not. The remaining 1,263(90.2%) women were normoglycemic 3 years postpartum, 1180/1263(84.3%) were at 3 months, while 83/1263(6.08%) had AGR and became normoglycemic. Women with GDM were more likely to progress to AGR 3 years postpartum (OR:1.60[1.33-1.92]) and less likely to remain normoglycemic (OR:0.22[0.15-0.33]) versus non-GDM women. Having >2/3 unmodifiable RF was associated with a reduced rate of maintained normoglycemia (OR:0.56[0.39-0.80]) and an increased risk of progression to AGR (OR:1.90[1.28-2.83]). Having >5/12 modifiable RF was associated with a reduced rate of maintained normoglycemic (OR:0.74[0.51-0.99]) and reversion of AGR (OR:0.49[0.25-0.97]), an increased progression to AGR (OR:1.40[1.00-2.09]), and persistence of AGR (OR:2.57[1.05-6.31]). Pre-gestational BMI≥25kg/m2 (OR:1.80[1.19-2.71]), post-delivery weight gain (OR:2.22[1.10-4.48]), and waist circumference >89.5cm (OR:0.54[0.36-0.79]), (all p<0.05) were the main modifiable RF. Conclusions: RF related to an increased probability for 3-year-postpartum AGR despite 3-month normoglycemia were identified, potentially useful when designing personalized strategies for pregnant women, directed towards minimizing unfavorable outcomes.

Diaminomaleonitrile (DAMN) is an electron-rich ligand which is commonly used in the synthesis of purines, amides and Schiff base ligands. In the last case lies the interest in this molecule, given its symmetry and apparent facility to form various ligands and complexes of interest in fields such as organic solar cells and catalysis among others. Nevertheless, its bisubstitution with aldehydes displays certain difficulty due to the double conjugated presence of the nitrile group (C≡N) in its structure, which significantly affect its coordination behavior by modulating the chemical reactivity of its amines. In addition to presenting a practical resume of guidelines for the preparation of different bisubstituted compounds from DAMN, this paper reviews the possibility of attaining a precise characterization by simple spectroscopic techniques. We provide an additional discussion for one of these techniques (commonly reported but often overlooked), given its potential to provide both the symmetry and E/Z configuration of the product. We hope the comprehensive evidence discussed and shown in this review will be helpful to further develop and understand the products derived of this interesting molecule in their broad applications.

Pomegranate juice possesses therapeutic properties against metabolic syndrome. Microencapsulation of pomegranate juice (MPJ) may extend its shelf life; however, further research is necessary to ascertain its comparative efficacy with fresh juice. This work evaluated the effect of (MPJ) in an animal model with induced metabolic syndrome (MetS). Male Wistar rats were induced-MetS by administering 30% sucrose orally for 22 weeks. Once MetS was verified in the animals, 7 groups were formed as follows: control (Ctrl); MetS, MetS+Placebo; Ctrl+MPJ; MetS+MPJ1 600, MetS+MPJ2 1800, and MetS+MPJ3 2900 mg/kg. Systolic and diastolic blood pressure, glucose, triglycerides, and total HDL-c levels in the MetS+MPJ groups improved significantly (p &lt; 0.05) vs. the MetS group at the end of the study. Microencapsulation maintained the anti-metabolic syndrome properties of pomegranate juice and could be used to control metabolic syndrome.

This study develops a structure for mapping native vegetation in a transition area between Brazilian Cerrado and Atlantic Forest from integrated spatial information from the Sentinel-1 and Sentinel-2 satellites. Most studies use this data separately, however, the integrated use of optical sensors with Synthetic Aperture Radar (SAR) sensors can improve the methodology for classifying land use and land cover (LULC). The fusion of Sentinel-1 and Sentinel-2, for example, can increase the accuracy of mapping algorithms, using complementary information, such as spectral, backscattering, polarimetry, and interferometry. The study area comprises the Lobo Reservoir Hydrographic Basin, which is part of an environmental conservation unit protected by Brazilian law and with significant human development. LULC were classified, using the random forest deep learning algorithm. The classifying attributes were backscatter coefficients, polarimetric decomposition, and interferometric coherence for radar data (Sentinel-1), and optical spectral data, comprising bands in the red edge, near infrared, and shortwave infrared (Sentinel-2). The attributes were evaluated in three settings in which the SAR and optical data were evaluated separately (C1 and C2, respectively) and in an integrated manner (C3). The study found greater accuracy for C3 (96.54%), an improvement of nearly 2% compared to C2 (94.78%) and more than 40% in relation to C1 (55.73%). The classification algorithm encountered significant challenges in identifying wetlandsin C1, but performance improved in C3, enhancing differentiation by stratifying a greater number of classes during training and facilitating visual interpretation during sampling. Accordingly, the use of SAR and optical data becomes an alternative to optimize LULC mapping in tropical regions, due to the limited influence of atmosphere on images in the microwave range.

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

The results of the bibliographic analysis show that the most explored nanomaterials in dentistry are graphene and carbon nanotubes, and their derivatives. A detailed analysis and a comparative study on their applications show that, although they are quite similar, graphene based materials seem to be more promising for most of the applications of interest in dentistry. The bibliographic study also demonstrated the potential of zeolite based materials, although the low number of studies on their applications shows that they have not been totally explored, as well as other porous nanomaterials that found important applications in medicine, such as metal organic frameworks, have not been explored. Subsequently, it is expected that the research effort will concentrate in graphene and zeolite based materials in the incoming years. Thus, present review paper presents a detailed bibliographic study, with more than 200 references, in order to describe briefly the main achievements that have been described in dentistry using nanomaterials, compare and analyze them in a critical way, with the aim of predicting the future challenges.

Traditional winglets are designed as fixed devices attached at the tips of the wings. The primary purpose of the winglets is to reduce the lift-induced drag, therefore improving aircraft performance and fuel efficiency. However, because winglets are fixed surfaces, they cannot be used to control lift-induced drag reductions or to obtain the largest lift-induced drag reductions at different flight conditions (take-off, climb, cruise, loitering, descent, approach, landing, and so on). In this work, we propose the use of variable cant angle winglets which could potentially allow aircraft to get the best all-around performance (in terms of lift-induced drag reduction), at different flight phases. By using computational fluid dynamics, we study the influence of the winglet cant angle and sweep angle on the performance of a benchmark wing at Mach numbers of 0.3 and 0.8395. The results obtained demonstrate that by adjusting the cant angle, the aerodynamic performance can be improved at different flight conditions.

This paper presents the design and implementation of a remote supervision and control system for a gunpowder drum filling plant. The use of technologies such as SCADA (Ignition), IoT (Node-RED), ERP (Odoo) and digital twins (Factory I/O) to achieve remote monitoring and operation of the plant is described. The solution allows full control of the production process from any location through customized graphical interfaces. The challenges encountered in integrating multiple systems and platforms are discussed, along with the security measures implemented within the Azure cloud environment. The results demonstrate the effectiveness of 4.0 technologies in automating and digitizing critical industrial processes. This research will lay the groundwork for the adoption of these approaches in companies seeking greater efficiency, traceability and safety in their operations. The experience gained allows us to successfully face the digital transformation in modern manufacturing.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

Coffee is one of the most valuable agricultural products worldwide, and it is crucial to have efficient tools to obtain reliable information about production. This study aims to estimate coffee plantation production using segmentation and deep learning techniques in RGB images. Photographs of coffee plants were taken in Tabaconas, San Ignacio-Cajamarca, to create a dataset of crops during the harvest stage. The images were segmented to detect coffee fruits. A deep learning method was developed with YOLOv5 to detect the fruits and OpenCV to count them. The results showed that YOLOv5 achieved an accuracy of 97.25%, a recall of 95.77%, and an F1-Score of 96.37%, demonstrating high reliability in detecting coffee fruits. The average detection time per image was 17.9 seconds. The metrics were evaluated using a confusion matrix, highlighting the model's good performance. In conclusion, segmentation and deep learning techniques, along with counting algorithms developed with OpenCV, proved effective for estimating coffee production. This approach provides a valuable tool for farmers, improving crop management and facilitating decision-making in precision agriculture.

Pinus patula is one of the most planted wood conifer species worldwide; however, no foliar nutrient standards exist for this species up to date. The objective of the present study was to generate and verify two sets of foliar nutrient standards for nearly ten-year-old P. patula trees: critical nutrient concentrations and DRIS norms. Nutrients studied were N, P, K, Ca, Mg, Fe, Cu, Zn, Mn, and B. The reference standards were verified experimentally by installing two fertilization trials; one of them located in Huayacocotla, state of Veracruz and the other one in Aquixtla, state of Puebla, Mexico. Nutrient status of each fertilization trial was correctly predicted by critical nutrient values and DRIS as well. Both standards were able to detect the secondary growth-limiting nutrient deficiency in the Huayacocotla trial, where the primary limitation for growth was scarcity of solar radiation within tree crowns. The limiting nutrient in both experimental trials was K.

Herpes simplex virus type 1 (HSV-1) is a neurotropic virus that, occasionally, may spread to the central nervous system (CNS), being the most common cause of sporadic encephalitis. One of the main neurovirulence factors of HSV-1 is the protein ICP34.5 that, although initially seemed to be relevant only in neuronal infections, it can also promote viral replication in non-neuronal cells. New ICP34.5 functions have been discovered during the recent years, and some of them have been questioned. This review describes the mechanisms of ICP34.5 to control cellular antiviral responses and debates its most controversial functions. One of the most discussed roles of ICP34.5 is autophagy inhibition. Although autophagy is considered a defense mechanism against viral infections, current evidence suggests that this antiviral function is only one side of the coin. Different types of autophagic pathways interact with HSV-1 impairing or enhancing the infection, and both the virus and the host cell modulate these pathways to tip the scales in its favor. In this review, we will summarize the recent progress on the interplay between autophagy and HSV-1, focusing on the intricate role of ICP34.5 in the modulation of this pathway to gain the battle against cellular defenses.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

MATERIAL AND METHOD: This is an observational analytical cohort study carried out on a total of 160 patients, divided into 4 groups: healthy, with myopia, with primary open-angle glaucoma (POAG), and with POAG and myopia together. The study variables were Bruch's membrane opening area (BMO), the thickness of the RNFL and the RGC layer using the Glaucoma Premium program of the OCT Spectralis of Heidelberg. RESULTS: Regarding the analysis between age and the thickness of the RNFL, significant results were found in the healthy and glaucoma groups with myopia, for the rest of the groups, although there are no significant results, the correlation is negative, the older the younger is the thickness. Regarding intraocular pressure (IOP), significant results have been found in the nasal sector in the glaucoma group. In the glaucoma with myopia group, statistically significant results have been obtained when analyzing the thickness of the RNFL with refraction. In the analysis between the thickness of the RNFL and the RGC layer, significant results were obtained in the myopia and glaucoma groups; in the group of glaucoma with myopia, it occurs in the superior temporal sector. CONCLUSION: In the case of myopic patients with glaucoma, damage at the functional, both the thickness of the RNFL, the RCG and the BMO-MRW are greater than other groups. All these alterations can be evaluated and monitored with the OCT Spectralis thanks to the programs it includes, making this instrument one of the best for an early diagnosis of glaucoma and the damage produced in myopic patients.

The aim of this work was to classify the business incubators in Spain according to the four phases of the startup’s incubation process. Considering that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the business incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis has been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors. Finally, the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3, named activity monitoring and control, was related to phase 3 or basic incubation variables. Cluster analysis facilitates the grouping of business incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small sized business incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factors 1 and 2. Factor 3, although positive, it is susceptible to improvement. They are the largest group of business incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

We extensively studied serigraphic screen-printed commercial silver flake inks loaded with silicon inclusions in order to achieve pinning at the grain boundaries. Based on grain size measurements using electron backscattered diffraction (EBSD), commercial silver ink with silicon microparticle content of 5 wt.% shows a significant grain growth retardation compared to the pristine silver ink, which stabilizes electrical conductivity up to 700 ◦C via Zener pinning mechanism. The modified silicon-loaded silver ink experiences a two times increase in grain size when heated up to 700 ◦C, compared to a seven times increase for the pristine silver ink. In turn, this enables operation temperatures significantly higher than the conventional operational window of microparticle-based silver inks, which are usually limited to 400 ◦C. Using isothermal exposures of 10 minutes up to 4 hours this phenomenon is observed at temperatures ranging from 250 ◦C to 900 ◦C. The electrical conductivity stability, grain size evolution and oxide contents were studied up to 4 hours. The activation energy of silver ink with silicon inclusions is 54% lower than for the pristine silver ink due to pining effect, which retards grain growth via the Zener mechanism. Most importantly, the electrical resistivity becomes stable up to 700 ◦C, which is more than twice the operation limit for off-the-shelf screen-printable silver flake inks. Hence, we demonstrate that adding controlled amounts of silicon particles to silver inks towards grain structure engineering can open new vistas of possibilities for screen-printed metallic inks.

In recent years, research has focused on generating mechanisms to assess the levels of subjects' cognitive workload when performing various activities that demand high concentration levels, such as driving a vehicle. These mechanisms have implemented several tools to analyze cognitive workload where the electroencephalographic (EEG) signals are the most used due to its high precision. However, one of the main challenges in the EEG signals implementing is finding the appropriate information to identify cognitive states. Here we show a new feature selection model for pattern recognition using information from EEG signals based on machine learning techniques called GALoRIS. GALoRIS combines Genetic Algorithms and Logistic Regression to create a new fitness function that identifies and selects the critical EEG features that contribute to recognizing high and low cognitive workload and structures a new dataset capable of optimizing the model's predictive process. We found that GALoRIS identifies data related to high and low cognitive workload of subjects while driving a vehicle using information extracted from multiple EEG signals, reducing the original dataset by more than 50%, maximizing the model's predictive capacity-achieving a precision rate greater than 90%.

Biofilm formation is important in the free-living and symbiotic lifestyles of Sinorhizobium meliloti. Here we show that the S. meliloti NspS-MbaA system is homologous to the c-di-GMP modulating NspS-MbaA system described in Vibrio cholerae and modulates biofilm formation, exopolysaccharide (EPS) production and motility in S. meliloti in response to exogenous polyamines. Biofilm and EPS production in quorum sensing-deficient wild type strain 1021 decreased in cultures containing putrescine, 1,3-diaminopropane or spermine, but were unaffected in a 1021 nspS mutant (1021 nspS). Decreases in biofilm formation caused by these polyamines paralleled decreases in EPS production and increases in nspS transcription. Cell aggregation did not differ markedly between strain 1021 and 1021 nspS. The S. meliloti quorum sensing-proficient Rm8530 wild type strain and nspS mutant (Rm8530 nspS) produced similar levels of biofilm under control conditions and 3.2- and 2.2-fold more biofilm in cultures with norspermidine, but these changes did not correlate with EPS production. Rm8530 nspS aggregated up to several fold more than the wild type under most conditions. Changes caused by polyamines in swimming and swarming motility were not generally dependent on NspS-MbaA in either 1021 or Rm8530. We speculate that the S. meliloti NspS-MbaA system could modulate biofilm formation in response to environmental polyamines.

Cancer is a disease that encompasses multiple and different malignant conditions and is among the leading causes of death in the world. Therefore, the search for new pharmacotherapeutic options and potential candidates that can be used as treatments or adjuvants to control this disease is urgent. Natural products, especially those obtained from plants, have played an important role as a source of specialized metabolites with recognized pharmacological properties against cancer, therefore, they are an excellent alternative to be used. The objective of this research was to evaluate the action of the monoterpene isoespintanol (ISO) against the human tumor cell lines MDA-MB-231, A549, DU145, A2780, A2780-cis and the non-tumor line MRC-5. Experiments with MTT and fluorescence with propidium iodide (PI), DAPI and green plasma revealed the cytotoxicity of ISO against these cells; furthermore, morphological and chromogenic studies revealed the action of ISO on cell morphology and the inhibitory capacity on reproductive viability to form colonies in MDA-MB-231 cells. Likewise, 3D experiments validated the damage in these cells caused by this monoterpene. These results serve as a basis for progress in studies of the mechanisms of action of these compounds and the development of derivatives or synthetic analogues with a better antitumor profile.

This study aimed to analyze the population dynamics of the mite Varroa destructor in honey bee (Apis mellifera) colonies in a temperate semi-arid climate in Mexico. Ten colonies homogeneous in population, food stores, and levels of mite infestation, were used. The mite infestation rate in brood and adult bees, total number of mites, daily mite fall, brood and adult bee population, and food stores, were determined periodically for 10 months. There was a significant effect (P &lt;0.05) of sampling period on the population of V. destructor in adult bees, brood, total mite population, and daily fallen mites. The total mite population increased 26% on average per colony. The increase in brood amount reduced the mite infestation rate in adult bees, and the opposite occurred when the brood decreased. Monitoring V. destructor populations by recording fallen mites is more reliable than determining mite infestation rates in bees, as mite fall has a dynamic pattern similar to that of the total mite population. The best period to apply an acaricide treatment in the region of study is between November and December because most mites were in the phoretic phase, since there was less brood in the colonies compared to other times.

Background: Although confirmed cases of infection with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) have been declining since late 2020 due to general vaccination, little research has been done regarding the impact of vaccines against SARS-CoV-2 in Spain in terms of hospitalizations and deaths. Objective: Our aim was to identify the reduction in severity and mortality of coronavirus disease 2019 (COVID-19) at a nationwide level due to vaccination. Methods: We designed a retrospective, population-based study to define waves of infection and to describe the characteristics of the hospitalized population. We also studied the rollout of vaccination and its relationship with the decline in hospitalizations and deaths. Finally, we developed two mathematical models to estimate non-vaccination scenarios using machine learning modeling (with the ElasticNet and RandomForest algorithms). The vaccination and non-vaccination scenarios were eventually compared to estimate the number of averted hospitalizations and deaths. Results: In total, 498,789 patients were included, with a global mortality of 14.3%. We identified six waves or epidemic outbreaks during the observed period. We established a strong relationship between the beginning of vaccination and the decline in both hospitalizations and deaths due to COVID-19 in all age groups. We also estimated that vaccination prevented 170,959 hospitalizations (CI 95% 77,844–264,075) and 24,546 deaths (CI 95% 2,548–46,543) in Spain between March 2021 and December 2021. We estimated a global reduction of 9.19% in total deaths during the first year of COVID-19 vaccination. Conclusions: Demographic and clinical profiles changed over the first months of the pandemic. Patients over 80 years old and other age groups obtained clinical benefit from early vaccination. The severity of COVID-19, in terms of hospitalizations and deaths, decreased due to vaccination.

This study presents the development and implementation of a remote monitoring system for a dual-axis solar tracker, integrating Industry 4.0 technologies such as IoT, SCADA, and MQTT. The system, which combines a Siemens S7-1200 PLC, an IoT gateway, and a SCADA platform based on Ignition, demonstrated significant increases in solar capture efficiency, with production gains of 25-30% compared to fixed systems, reaching up to 67.65% under ideal conditions. In addition to improving operational management through predictive monitoring and early fault detection, the study identified areas for improvement, such as the need for real-world testing and the integration of weather predictions. In conclusion, the research validates the feasibility and effectiveness of automated IoT and SCADA-based systems to optimize solar trackers, significantly contributing to improved energy efficiency in photovoltaic installations.

This paper is a detailed study on radio frequency identification (RFID) technology focused on its application for warehouse traceability in the company FRUMECAR. It highlights the importance of controlling the traceability of items in warehouses or logistics companies, highlighting the need for reliable, real-time information to effectively manage inventory and resolve incidents quickly. The paper discusses in depth what RFID is, its types, main components such as tags, readers, and antennas, as well as discussing how it works, advantages, disadvantages, and specific applications. It also examines factors such as return on investment, cost feasibility, and environmental factors that influence the implementation of RFID systems. The paper presents a practical approach, proposing RFID-based solutions to improve traceability in FRUMECAR, analyzing the current state of the company and its warehouses, with the aim of implementing an efficient system that allows real-time tracking of products.

This work presents a novel compact CMOS potentiostat designed circuit for electrochemical cell. The proposed topology functions as a circuit interface, controlling the polarization of voltage signals at the sensor electrodes and facilitating current measurement during the oxidation-reduction process of a analyzed solution. The potentiostat, designed for CMOS technology, comprises a two-stage amplifier, two current mirror blocks coupled to this amplifier, and a CMOS push-pull output stage. It employs the electrochemical method of cyclic voltammetry, operating within voltage range of ±0.8 V and scan rates of 10mV/s, 25mV/s, 100mV/s and 250 mV/s. The circuit is capable of reading currents ranging from 10 µA to 500 µA. Experimental results were obtained using a potassium ferrocyanide (K3(FeCN)6) redox solution with concentrations of 10, 15 and 20 mmol/L, and their corresponding voltammograms were evaluated. The experimental results from a discrete circuit demonstrate that the proposed potentiostat topology produces outcomes consistent with those of classical topologies presented in the literature and industrial equipment.

Efforts to optimize the design and enhance the efficiency of standing-wave thermoacoustic refrigerators (SWTAR), particularly those with parallel plate stacks, are crucial for achieving rapid and straightforward engineering estimates. This study primarily focuses on optimizing the Coefficient of Performance (COP) by combining the linear thermoacoustic theory (LTT) with the Design of Experiments (DOE) approach. The investigation centers around five key parameters affecting the COP, once the working gas is selected. Then, based on the LLT theory, the COP was estimated numerically, over defined intervals of those five parameters. Moreover, through quantitative and qualitative effect analyses, these five parameters and their interactions are determined. Utilizing a transfer function and surface response analyses based on the COP, the study aims to delineate the best COP value as well as the contribution of the thermoacoustic parameters and their interactions. Furthermore, a comparison between contour and surface responses and several statistical decision approaches applying the Full Factorial Design verify the robustness of the study’s findings. Ultimately, the COP results obtained align with existing literature, underscoring the validity and relevance of the study’s methodologies and conclusions.

Solar radiation corresponds to fundamental parameters for solar photovoltaic (PV) technology. Reliable solar radiation prediction became valuable to design solar PV systems, performance, operatively efficient planning, safety operation, grid dispatch and financial characteristics. However, high quality ground-based solar radiation measurements are scarce, especially for very short-term time horizon. Most of the existent studies trained the machine learning (ML) model used dataset with time horizon of 1-hour or day, very fewer studies have been reported using a dataset with a 1-mitute time horizon. In this study, a comprehensive evaluation of nine ensemble learning algorithms (ELA) is performed to estimate the solar radiation in Santo Domingo with a 1-minute time horizon dataset collected from a local weather station. The ensemble learning evaluated included seven homogeneous ensembles; Random Forest (RF), Extra Tree (ET), Adaptive Gradient Boosting (AGB), Gradient Boosting (GB), Extreme Gradient Boosting (XGB), Light Gradient Boosting (LGBM), Histogram-based Gradient Boosting (HGB) and heterogeneous ensemble named as Voting and Stacking. RF, ET, GB, HGB were combined to develop Voting and Stacking and Linear Regression (LR) was adopted in the second layer of the Stacking. Five technical metrics, Mean Squared Error (MSE), Root Mean Squared Error (RMSE), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE) and Coefficient of Determination (R2) were used as criteria to determine the prediction quality of the developed ensemble algorithms. Comparison of the results indicates that the HGB algorithm offers superior prediction performance among the homogeneous ensemble learning and overall, the Stacking provides the best accuracy with metric values of MSE=3218.27, RMSE= 56.73, MAE=29.87, MAPE=10.60, R2=0.964.

Currently, the use of medications during pregnancy in Latin America is common; studies with Latin American samples find that nearly 90% of pregnant women use some medication at least once during pregnancy. Furthermore, approximately 21% of the respondents self-medicated. Worldwide, the prevalence of this disease is 32%. The most common medications are nonsteroidal anti-inflammatory drugs and analgesics. Many of these drugs are available over the counter without a prescription. For this reason, a systematic review of the literature on the adverse effects on the woman and the fetus was performed. Objective: To determine the adverse effects associated with the use of nonsteroidal anti-inflammatory drugs (NSAIDs) on pregnant women and fetuses during pregnancy. Methods: Systematic literature review. The following search strategy was used for the databases: Science Direct, PubMed, Scopus and Web of Science, through September 3, 2022. The population of pregnant women without previous comorbidities was defined. The intervention of interest was the use of NSAIDs during pregnancy. The outcomes of interest were adverse effects for the mother or fetus (weight of the newborn, congenital malformations present in the fetus, systemic effects in the pregnant woman during her gestation period). The types of studies included clinical trials, cohort studies and case‒control studies. Results: 1 study included 2,985 pregnant women without previous comorbidities. The use of aspirin more frequently during pregnancy stands out. The adverse effects on the fetus were preterm birth <37 weeks, low birth weight < 2500 g and increased admission to the neonatal intensive care unit. No adverse effects were found for the mother. Conclusions: There are not enough data indicating that the use of NSAIDs during pregnancy is safe. Some studies show that the use of NSAIDs during pregnancy could be related to problems in the development and growth of the fetus and health effects for the mother during pregnancy, so it is advisable to use these drugs under medical prescription and for the shortest possible time. in the gestation stage.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

Background: In 2020, the incidence of cancer was 844,778 cases among the population aged 0 to 19 years. Ninety percent of the population under 18 years of age lives in low- and middle-income countries, where cancer survivors report adverse outcomes. disease, which negatively impacts individuals’ general health, emotional state and external factors such as academic performance. Therefore, the objective of this article was to report the performance of the WCST and the sociodemographic characteristics of oncopediatric patients from Cali, Colombia. We report the reliability of the WCST instrument and indicate the association between the type of cancer and executive functioning in patients. Methods: In a cross-sectional observational study, 24 oncopediatric patients were interviewed and evaluated via the WCST. Results: The mean age was 12.08 years (3.98), 20.8% were women, 70.8% had a diagnosis of leukemia, 8 patients had acquired brain deficits, and more than 75% had adequate functioning in terms of the indicators of executive functions. Robust statistics were used to explore the differences between the types of diagnoses and performance in executive functions, and no statistically significant differences were found (p = 0.156). We accumulated evidence that the WCST has a reliable Cronbach's α of 0.804 and that oncopediatric patients without brain deficits had high scores for executive functions (p = 0.002) with a moderate effect size (0.727). Conclusions: The WCST is reliable for discriminating executive function among pediatric cancer patients. The evidence suggests that there are no differences between the types of cancer evaluated and executive functioning in the participants.

Two granulysin (GRNLY) based immunotoxins were generated, one containing the scFv of the SM3 mAb (SM3GRNLY) and the other the scFv of the AR20.5 mAb (AR20.5GRNLY). These mAb recognize different amino acid sequences of aberrantly O-glycosilated MUC1, also known as the Tn antigen, expressed in a variety of tumor cell types. We first demonstrated the affinity of these immunotoxins for their antigen using surface plasmon resonance for the purified antigen and flow cytometry for the antigen expressed on the surface of living tumor cells. The induction of cell death of tumor cell lines of different origin positive for Tn antigen expression was stronger in the cases of the immunotoxins than that induced by GRNLY alone. The mechanism of cell death induced by the immunotoxins was studied, showing that the apoptotic component demonstrated previously for GRNLY was also present, but that cell death induced by the immunotoxins included also necroptotic and necrotic components. Finally, we demonstrated the in vivo tumor targeting by the immunotoxins after systemic injection using a xenograft model of the human pancreatic adenocarcinoma CAPAN-2 in athymic mice. While GRNLY alone did not have a therapeutic effect, SM3GRNLY and AR20.5GRNLY reduced tumor volume by 42 and 60%, respectively, compared with untreated tumor-bearing mice, although the results were not statistically significant in the case of AR20.5GRNLY. Histological studies of tumors obtained from treated mice demonstrated reduced cellularity, nuclear morphology compatible with apoptosis induction and active caspase-3 detection by immunohistochemistry. Overall, our results exemplify that these immunotoxins are potential drugs to treat Tn-expressing cancers.

The genus Prototheca, unicellular, non-photosynthetic, yeast-like microalgae, is a pathogen of concern for the dairy industry causing bovine mastitis that currently cannot be cured and hence generates significant economic losses in milk production. In this study, for the first time in Ecuador, we identify Prototheca bovis as the etiologic agent of chronic mastitis in dairy cattle. Milk samples (n=458) of cows with chronic mastitis were cultured on Sabouraud Dextrose Agar (SDA). Microscopy and cytB gene sequencing were used to identify Prototheca, whereby Prototheca bovis was isolated from 15.1% (n=69) of the milk samples, one of the highest infection rates that can be found in the literature in a “non-outbreak” situation. No other Prototheca species were found. We were unable to isolate the alga from environmental samples. We showed that P. bovis was relatively resistant to disinfectants used to sterilize milking equipment on the cattle farms where it was isolated. We discuss how to avoid future infection and also hypothesize that the real prevalence of Prototheca infection in bovine mastitis is probably much higher than what was detected. We recommend a protocol to increase the diagnostic yield in the bacteriology laboratory.

The simplest possible structural transition that an electronic system can undergo is Wigner crystallization. The aim of this short review is to discuss the main aspects of three recent experimets on the one dimensional Wigner molecule, starting from scratch. To achieve this task, the Luttinger liquid theory of weakly and strongly interacting fermions will be shortly addressed, together with the basic properties of carbon nanotubes that are require. Then, the most relevant properties of Wigner molecules will be addressed, and finally the experiments will be described.

This work presents an application called APPMAR 1.0 based on Python ® environment, built to perform the downloading, treatment and analysis of meteorological and marine information. This application is composed of two main modules: the first module allows the downloading of information from the database (NOAA - WW3); the second module uses the principles of statistical mathematics for the treatment of waves and wind. The importance of this simple application is based on the free and agile access to meteorological and marine information for a coastal project. The determination of representative conditions of sea states ultimately will govern the process of design of coastal and oceanic infrastructure. The analysis of historical time series of local waves and winds allows the evaluation of average regimes or operational design, the ultimate limit states or extreme design, and the storms or design by persistence. In spite that the former analysis is a common task for coastal engineers, the codes generated are seldom shared for public use. In summary, for operational purposes is useful to have a freeware that can assist in the data processing for decision making and forcing of the mathematical models that are part of the common practice of coastal, oceanic and offshore engineering. This application has been tested in the Caribbean area of Colombia where meteorological and marine information are scarce.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

Aiming for the problems emerging in the PWM drive system with long cables, accurate modeling of power cables is the premise to predict and analyze the relevant phenomenon, and a proper filter design is the key solution to these problems. This paper proposes high-frequency cable models to represent the frequency-dependent characteristics, especially for the high-frequency resistance of the cable that is an easily overlooked factor but determines the damping of overvoltage. The proposed models can be used for accurately representing the cable parameters in a wide frequency range, and correctly simulating the differential mode (DM) overvoltage and common mode (CM) current, including the peak value, oscillation frequency and damping of the transient waveform. In addition, improved filter networks are proposed to suppress the DM voltage and CM current, with the merit of low losses, small volume and an excellent ability of suppressing overvoltage. The proposed cable models and the filter design have been validated in a 750W PWM drive system with 200m power cables.

In Mexico viticulture represents the second source of employment in the agricultural area after the fruit and vegetable sector. In developed countries, remote sensing is widely used for vineyard monitoring, however, this tool is barely used in developing countries of Iberoamerica. In this re-search, our overall objective is to characterize two vineyards in the state of Queretaro (Mexico) using Sentinel-2 and meteorological data, specifically spectral and thermal indices. Results showed that spectral indices obtained from Sentinel-2 bands have characterized adequately the phenolog-ical evolution of the different varieties of the vineyards. The Modified Soil-Adjusted Vegetation Index (MSAVI) was adequately used to discriminate the first stages of vineyards, while the Nor-malized Difference Vegetation Index (NDVI) was useful to monitor vineyards during the rest stages of vineyards. Thermal indices have shown that the best grape varieties were those that can adapt to both cooler and warmer temperatures, have a reasonable ripening period, and can produce wines with balanced acidity and flavors. In conclusion, the combination of meteorological (including thermal indices) and remote sensing data (NDVI and MSAVI) provide information for choosing the suitable grape variety for this region.

The daily path of the Sun across longitude yields night and day, but the Sun also travels across latitude on a belt 47° wide. The Sun meridian declination explains the annual budget of natural beam irradiance (NBI), which is the irradiance delivered to the Earth’s surface as a normal projec-tion from the Sun. Data for the sun meridian declination data were obtained from the geometric model. The distribution of NBI was weighed between the Tropics of Cancer and Capricorn. The variation patterns of the solar declination conform to the dynamics of pendular motion. The joint distributions of velocity or acceleration of meridian declination against declination fit circular graphs. The NBI budget fluctuates in inverse proportion to the velocity of declination, yielding 18 sun-paths per degree for latitudes above 20°, and 6 sun-paths per degree for latitudes under 20°. All sites of the planet, whose latitude coincide, whether within or between hemispheres, accumu-late an equivalent budget of NBI.

Intracranial hemorrhage is a serious medical problem that requires rapid and often intensive medical care. Identifying the location and type of any hemorrhage present is a critical step in the treatment of the patient. Diagnosis requires an urgent procedure, and the detection of hemorrhage is a difficult and time-consuming process for human experts. In this paper, we propose methods based on EfficientDet’s deep-learning technology that can be applied to the diagnosis of hemorrhages and thus become a decision-support system. Our proposal is two-fold. On the one hand, the proposed technique classifies slices of computed tomography scans for the presence hemorrhage or its lack, achieving 92.7% accuracy and 0.978 ROC-AUC. On the other hand, our methodology provides visual explanations of the classification chosen using the Grad-CAM methodology.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

Abstract: (1) Background: Minimally-invasive sacroiliac joint (SIJ) fusion is the preferred surgical intervention to treat chronically severe pain associated with SIJ degeneration and dysfunction. (2) Methods: This paper details the ten-step surgical procedure associated with the postero-inferior approach using the PsiF™DNA Sacroiliac Joint Fusion System. (3) Results: The posterior surgical approach with an inferior operative trajectory (postero-inferior) utilizes easily identifiable landmarks to provide the safest, most direct access to the articular joint space for transfixing device placement. Implanting the device through the subchondral bone, provides maximum fixation and stabilization of the joint by utilizing an optimal amount of cortical bone-implant interface. Approaching the joint from the inferior trajectory also places the implant perpendicular to the S1 endplate at a “pivot point” near the sacral axis of rotation, which addresses the most significant motion of the joint. (4) Conclusions: Further observational data from real-world clinical use are encouraged to further validate this procedure as the surgical preference for minimally-invasive SIJ fusion.

Minimizing optical losses in resonant cavities is crucial for improving photonic device performance. This study focuses on the development of a simulation tool to analyze scattering losses in Fabry-Pérot interferometers (FPI), offering precise modeling of waveguide dynamics and contributing to accurate loss predictions across various platforms. Optical cavities often suffer from scattering losses due to surface roughness and material defects. Our approach integrates theoretical models and simulations to quantify these losses, utilizing the FPI as a model system. We identified upper and lower reflectivity thresholds, beyond which accurate measurement of losses becomes unreliable. For reflectivity below a certain threshold, measurement errors arise, while excessively high reflectivity can reduce fringe visibility and introduce detector sensitivity issues. Simulations were used to validate the model's ability to predict reflectivity and attenuation in waveguides with varying loss levels. The software’s flexibility to adjust transmission parameters for different cavity configurations enhances its utility for a broad range of photonic systems. Our study offers a novel methodology for optical loss analysis, with practical applications in optimizing photonic devices. By providing a reliable tool for precise loss measurement, this work supports advancements in optical technologies, enabling the design of more efficient, high-performance devices across various applications.

Mitigation of Anthropogenic CO2 emissions possess a major global challenge for modern societies. Herein catalytic solutions are meant to play a key role. Among the different catalysts for CO2 conversion Cu supported on molybdenum carbide is receiving increasing attention. Hence, in the present communication we show the activity, selectivity and stability of fresh-prepared -Mo2C catalysts and compare the results with those of Cu/Mo2C, Cs/Mo2C and Cu/Cs/Mo2C in CO2 hydrogenation reactions. The results showed that all the catalysts were active and the main reaction product was methanol. The results showed that copper-cesium and molybdenum effectively interact and that cesium promoted the formation of metallic Mo. While, the incorporation of copper is positive to improve the activity and selectivity to methanol, the presence of Mo0 phase was detrimental for the conversion and selectivity. Moreover, the catalysts promoted by cesium underwent redox surface transformations during the reaction that diminished their catalytic performance. The molybdenum phase in Cu/Mo2C changes during reaction leading to metallic molybdenum and tuning the catalytic activity.

Tumors of the central nervous system produce adverse outcomes in everyday life; however, low-grade gliomas are uncommon in adults. For this reason, the objective is to describe the executive function of a 59-year-old adult neuro-oncological patient. Pre- and postintervention evaluation of neurological and neuropsychological functioning was performed through neuroimaging techniques (iRM, Spectroscopy, Electroencephalography), hospital history, psychological interview, and Wisconsin Card Classification Test (WCST). Executive performance exhibited a noticeable decline in typical and centile WCST results, as evidenced by deterioration in persistent scores, failure to maintain an attitude and difficulty learning from clinical samples. This information coincides with the evolution of the neuroimage over time. Finally, this topic is discussed in the literature.

As participating molecules in nucleic acids, nucleotides also have signaling functions and act as second messengers in both prokaryotic and eukaryotic cells, the most common example being cyclic AMP (cAMP). In bacteria, a great interest has arisen in studying nucleotide signaling. It has been determined that cyclic di-AMP (c-di-AMP), cAMP, and cyclic di-GMP (c-di-GMP) participate in biological events such as bacterial growth, biofilm formation, sporulation, cell differentiation, motility, virulence, and other. Moreover, these cyclic-di-nucleotides (c-di-nucleotides) produced in pathogenic intracellular bacteria can affect eukaryotic host cells for infection. On the other hand, the nucleotide molecules pppGpp, and ppGpp are alarmones involved in regulating bacterial nutritional stress; they are also considered second messengers. These second messengers can be used as therapeutic agents because of their immunological functions on eukaryotic cells. In this review, different topics on the role of c-di-nucleotides as second messengers in different bacterial processes are addressed.

The purpose of this article is to present a multi-criteria model designed to evaluate the potential of Sincelejo's cultural identity for tourism development. A descriptive quantitative methodology was used, which included a survey of 211 participants. A decision support method was applied, using the Weighted Additive Sum approach, following the multi-attribute method. Based on the information gathered, the elements of cultural identity shared by most of the criteria were identi-fied, highlighting the gastronomic, social, and cultural traditions and customs of the region, the results of which made it possible to design a composite indicator to evaluate the tourism potential of cultural identity in the area.

INTRODUCTION: Achalasia is a pathology with an incidence of 1 in 100,000 inhabitants per year. There are very limited data on achalasia in the obese population, especially in those undergoing bariatric surgery. The approach of choice for cases of achalasia is fundoplication to correct the reflux; however, lacking a fundus due to a previous gastrectomy, an alternative that offers optimal results should be chosen. Here we present the surgical approach in a case of esophageal achalasia and a history of vertical sleeve gastrectomy, where we performed simultaneous Heller's cardiomyotomy and laparoscopic Roux-en-Y gastric bypass, as well as the results obtained. CASE PRESENTATION: 44-year-old woman with no chronic degenerative diseases, with a previous record of vertical sleeve gastrectomy 5 years ago, who started 1 year and 5 months earlier with dysphagia to liquids, then to solids, in addition to weight loss of 10 kilograms in 4 months. The BMI before vertical sleeve gastrectomy was 32 kg/m2, her BMI at the time of admission was 20 kg/m2; she also presented regurgitation and generalized weakness. After analyzing the surgical options, it was decided to perform a Heller cardiomyotomy and a Roux-en-Y gastric bypass. DISCUSSION AND CONCLUSIONS: The procedure turned out to be safe and successful in treating achalasia symptomatology, in addition to complete resolution of the reflux symptom.

Infections due to Candida spp., they are a threat to global health, with high rates of morbidity and mortality due to their drug resistance, especially in immunocompromised people. Thus, the search for new alternatives is urgent today. In recent years, combined therapy with compounds of natural origin has been proposed as an alternative. Considering the biological potential of isoespintanol (ISO) and continuing with its study, the objective of this research was to assess the effect of ISO in combination with the antifungals, fluconazole (FLZ), amphotericin B (AFB) and caspofungin (CASP), against clinical isolates of C. tropicalis and evaluate the cytotoxic effect of this compound in the acute phase (days 0 and 14) and chronic phase (days 0, 14, 28, 42, 56, 70 and 84), in female mice (Mus musculus) of the Balb/c lineage. The results show that ISO can potentiate the effect of FLZ, AFB and CASP, showing synergism with these antifungals. Evaluation of the mice by direct vision showed no behavioral changes or variation in weight during treatment; furthermore, the analysis of the cytokines IFN-γ and TNF in plasma, peritoneal cavity lavage (PCL) and bronchoalveolar lavage (BAL) indicated that there was no inflammation process and histopathological studies of lung, liver and kidney showed no signs of toxicity caused by ISO; this was consistent with the analysis of oxaloacetic transaminases (GOT) and pyruvic transaminases (GPT), which remained in the standard range. These findings indicate that ISO does not have a cytotoxic effect at the doses evaluated. Our results place ISO as a monoterpene of interest in the search for compounds with pharmacological potential.

The individual and combined effects of extracellular products (ECP) from Arthrobotrys oligospora (Ao) and A. musiformis (Am) growth in liquid media against Haemonchus contortus L3 (HcL3) were assessed. The following methodological steps were established: isolation, morphological (MI) and molecular identification (Mol-I), assessment of nematocidal activity (NA) of fungal liq-uid culture filtrates (LCF) produced in two liquid media alone and in combination and finally, the myco-compound profile identification (MCP). The MI of both isolates suggested that the fungi corresponded to the species Ao and Am. This result was confirmed by PCR analysis followed by sequencing, alignment and obtaining coverage and similarity with respect to isolates reported in the NCBI database. Likewise, the highest Hc mortalities were 91.4% with individual LCF of Am and 86.2% with those of Ao at the highest concentration (100 mg/mL) in Czapek-Dox Broth. The combination of both LCF resulted in a similarly high larval mortality with no statistical differ-ences in relation to individual activity (P>0.05). The MCP showed the presence of alkaloids in both fungi. Coumarins, triterpenes and saponins were found only in Ao. Both fungi produced ECP with a high NA that could be identified and assessed in future studies as potential natural an-thelmintic compounds.

Background/Objectives: Listeria monocytogenes is a foodborne pathogen that can infect humans and animals, causing non-invasive gastrointestinal listeriosis or invasive listeriosis. The objectives of this study were to determine: the genetic diversity of L. monocytogenes; the genes associated with the resistance to antibiotics, benzalkonium chloride (BC), and CdCl₂, and biofilm formation. Methods: Seventeen strains of L. monocytogenes isolated fresh fruits and vegetables were selected for this study. Genetic diversity and the genes associated with antibiotic resistance were determined by PCR amplification. Susceptibility to antibiotics were determined using the agar diffusion method. Resistance to BC and CdCl₂ was determined using the minimum inhibitory concentration method. Capacity for biofilm formation was evaluated using the crystal violet staining method. Results: This study demonstrates that the isolates of L. monocytogenes belong to serotypes 1/2a (29.4%) and 1/2b (70.5%). Potential hypervirulent strains containing 70.5% Listeria pathogenicity island 1 (LIPI-1-2), 17.6% (LIPI-1-3), and 11.7% (LIPI-1-4) were also identified. Antibiotic susceptibility tests show that L. monocytogenes exhibit six different multiresistant patterns with a MAR index of ³ 0.46 (70.5%); besides, the gen Ide, tetM, and msrA were detected in 52.9%, 29.4%, and 17.6%, respectively, associated with efflux pump Lde, tetracycline and ciprofloxacin resistance. Phenotypic test shows that 58.8% cadmium-resistant L. monocytogenes have a co-resistance to BC of 23.5%. Subsequently, all strains of L. monocytogenes exhibited moderate biofilm. Conclusions: This study contributes to the persistence and genetic diversity of strains L. monocytogenes isolated fresh fruits and vegetables; in addition, resistance to CdCl₂ and correlation with co-resistance to BC disinfectant used in the food industry.

A via ferrata (from the German “klettersteig”, hereinafter VF) is a sports route located on forest and mountains vertical rock walls equipped with steps, chains, artificial dams, bridges and other fixed elements and which have a steel cable (safety cable) all the way along allowing users to secure their progress and avoid possible falls [1]. This article aims to analyse the state of the art of the VF sector in Spain, especially in terms of the regulations of obligatory compliance, in addition to defining the basic characteristics of the installations to ensure that these are safe for users, providing a previously non-existent summary of the most important recommendations regardless of the country where they are installed.

Introduction: The HIV/AIDS pandemic in Spanish prison institutions has led to a series of necessary changes to adapt and provide an effective response. Materials and Methods: This research was conducted from an interpretative paradigm with a phenomenological perspective, interpreting the experiences of nursing professionals in Spanish prison institutions. Focus groups were conducted with professionals who worked before and after the emergence of antiretroviral treatments through the Microsoft Teams platform, using the ATLAS Ti v.9 software. The project received approval from the Ethics Committee of the UJI university. Results: Limited dissemination of news in the press regarding HIV/AIDS and Spanish prisons was observed. Changes occurred in organizational, material, and personnel resources, requiring adaptation among nursing professionals. The available resources and difficulties are described, along with patient perspectives, the role of professionals, their environment, and their experiences, both positive and negative. Discussion and Conclusions: There is minimal visibility of the problem, and a description is provided of an adaptation process to the environment compatible with the Callista Roy´s model.

In this research work, an adaptive scheme for the coordinated protection of AC Microgrids using directional overcurrent (DOCR) relays is presented. Protection of AC MGs is a complex and challenging issue due to the dynamic nature of the network including, a) its capability to reconfigure the modes of operation ranging from grid-connected to the islanded mode, c) bidirectional-power flow capability, and c) integration of intermittent renewable energy resources with real-time variations in the resource availability. Consequently, the fault current contributions may largely vary depending upon the incident conditions on the network. Conventional protection schemes, generally designed for radial networks, and unidirectional power flow from the source end to the load may either mal-operate or exhibit very poor performance, if not adapted according to the dynamic conditions of the network. To address this issue, a communication-based adaptive protection scheme capable to adapt its settings according to the generation resource availability and network configuration is presented in this work. The proposed scheme consists of an intelligent central protection unit (ICPU) capable to update the settings and communicate it to the individual relays based on the pre-calculated offline settings. The directional overcurrent relays employed in the scheme use two-stage settings, i.e. definite time and inverse definite minimum time characteristics for the effective coordination among the downstream and upstream relays. An adaptive algorithm for ICPU operation is presented and a case study is implemented for a modified IEEE 9-bus system using DigSilent Power factory. The results for various scenarios including, a) grid-connected mode of operation, b) islanded mode of operation, and c) variable distributed generation mode are obtained and compared to the static scheme, which validates the effectiveness of the proposed scheme.

Subjective cognitive decline (SCD) would correspond to a preclinical phase of Alzheimer's disease. The aim of this study was to find associations between lifestyle individual factors compatible scores with cognitive impairment (CI) in SCD people. Methods: This is a case-control study to detect SCD, CI and potential associated factors in 497 patients over 50 years in Community Pharmacies. Three screening tests detected possible CI and patients with at least one test compatible with CI were referred to Primary Care to be evaluated. Results: In self-complaint patients statistically significant with depressive feelings were found (86.8%) with benzodiazepines consumers (83.9%) and female patients (81.2%). Thirty percent of our sample obtained scores compatible with CI. Being older than 70 years old increased the odds of obtaining scores compatible with CI. High level education, reading and internet use were able to reduce the odds of positive scores compatible with CI (37%-91%, 7%-18% and 67%-86%), whereas, one extra hour television/day increased the risk in 8%-30%. Reading was able to nullify the effect of both internet and TV consumption. Conclusion: Not just the age but also modifiable lifestyle factors are acting in favour of a cognitive decline.

Smart grid software interconnects multiple Engineering disciplines (power systems, communication, software and hardware technology, instrumentation, big data, etc.). The software architecture is an evolving concept in smart grid systems in which systematic architecture development is a challenging process. The architecture has to realize the complex legacy power grid systems and cope up with current Information and Communication Technologies (ICT). The distributed generation in smart grid environment expects the software architecture to be distributed and to enable local control. Smart grid architecture should also be modular, flexible and adaptable to technology upgrades. In this paper, the authors have made a comprehensive review on architecture for smart grids. An in depth analysis of layered and agent based architectures is presented and compared under various domains.

Seaports are well known as the medium that has evolved into the central link between sea and land for complex marine activities. The growth in maritime logistics especially necessitates a large volume of energy supply to maintain the operation of sea trade, resulting in an imbalance between the generation and demand sides. Future projections for three major concerns show an increase in load demand, cost of operation, and environmental issues. In order to overcome these problems, integrating microgrids as an innovative technology in the seaport power system appears to be a vital strategy. It is believed that microgrids enhance the seaport operation by providing sustainable, environmentally friendly, and cost-effective energy. Despite the fact that microgrids are well established and widely used in a variety of operations on land, their incorporation into the seaport is still limited. The involvement of a variety of heavy loads such as all-electric ships, cranes, cold ironing, and buildings infrastructure makes it a complicated arrangement task in several aspects, which necessitate further research and leave space for improvement. In this paper, an overview of the seaport microgrids in terms of their concepts, requirements, and operation management is presented. It provides the perspectives of integrating the microgrid concept into a seaport from both shore side and seaside as a smart initiative for the green ports vision. Future research directions are discussed towards the development of more efficient marine power system.

Tuberculosis (TB) associated with diabetes (DM) is a growing problem, particularly in low and medium-resource countries. We conducted an open-label, parallel-group, randomized, and controlled trial in a tertiary care center in Mexico City to assess TB preventive treatment with isoniazid (INH) or rifampicin (RIF) in people with DM. Participants were assigned six months of INH 300mg/day plus pyridoxine 75mg or three months of RIF 600mg/day. The primary outcomes were adverse events resulting in permanent treatment cessation and considered possibly or probably related to study drugs. We included 130 subjects, 68 randomized to INH and 62 to RIF. We prematurely halted the study based on recommendations of the Adverse Event Safety Panel. There was no difference between arms in the overall frequency of adverse events. However, the INH group had significantly more permanent treatment interruptions due to grade 2 recurrent or grade 3 or 4 hepatoxicity. In comparison, the RIF arm had more treatment interruptions due to grade 3 or 4 gastrointestinal intolerance. TB preventive treatment is not safe enough to be considered a universal indication to patients with DM and LTBI. These results underline the need to search for alternative TB prevention in DM patients with better safety profiles.

Climate change has become a major concern for developing countries given the risk that it posses on energy and food independence, and on general productivity. Despite having an energy system with low carbon intensity when compared to other Latin American countries, Colombia is already facing climate change impacts and requires urgent efforts to mitigate them. As a developing country, the challenge is bigger as policies for economic growth should be in line with the global commitment of reducing greenhouse gas emissions. With the aim of contributing to the design of climate policies, this study assesses the impact of economic development on the environment by examining the validity of the Environmental Kuznets Curve hypothesis for Colombia. Statistically validated and stable autoregressive distributed lag models are estimated for three different environmental indicators: carbon dioxide emissions, methane emissions, and ecological footprint. Moreover, the effects of other variables such as urbanization, foreign direct investment, value added of agricultural and industrial sectors, and energy use are analyzed with dynamic simulations. Empirical evidence supports a long-run equilibrium relationship among investigated variables and the existence of an inverted U-shaped EKC relationship between Gross Domestic Product (GDP) and methane emissions, and GDP and ecological footprint. Shifting to renewable energy sources and leveraging the use of cleaner technologies in agricultural and industrial sectors are found to be key for economic growth without harming the environment.

We present a model of space that considers it to be a quantized dynamical entity which is a component of the universe along with matter and radiation. The theory is used together with thermodynamic data to provide a new view of cosmic evolution and an insight into the nature of dark energy and dark matter. Space is made up of energy quanta. The universe started from an atomic size volume at very high temperature and pressure near the Planck epoch. Upon expansion and cooling, phase transitions occurred resulting in the formation of radiation, fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters. From a phase diagram of cosmic composition, we obtained a correlation between dark energy and the energy of space. Using the Friedmann equations, data from WMAP studies of the composition of the universe at 3.0 x 10⁵ (a=5.25 x 10^-2) years and at present (a=1), are well fitted by our model with an equation of state parameter, w= -0.7. The accelerated expansion of the universe, starting at about 7 billion years, determined by BOSS measurements, also correlates well with the dominance of dark energy at 7.25 x 10⁹ years ( a= 0.65). The expansion can be attributed to Quintessence with a space force arising from a quantum space field. From our phase diagram, we also find a correlation suggesting that dark matter is a plasma form of matter similar to that which existed during the photon epoch immediately prior to recombination. Our Quantum Space Model leads to a universe which is homogeneous and isotropic without the need for inflation. The thermodynamics of expansion is consistent with BOSS data that show the process to be adiabatic and the rate of expansion decelerating during the first 6 billion years after the Big Bang. However, it became non-adiabatic and accelerating thereafter. This implies an influx of energy from a source outside the universe; it warrants consideration as a possible factor in the accelerated expansion of the universe.

ChatGPT has significantly increased in popularity in recent months because of its capacity to generate novel content and provide genuine responses to questions. Nevertheless, like all technologies, it is crucial to assess its limitations and features prior to implementing it into an educational setting. A major obstacle associated with ChatGPT is its tendency to produce consistent yet occasionally unreliable and inaccurate responses. Our study provides students with training in this area, and its objective was to analyse the opinion of those same university students studying education-related degrees regarding the efficacy of the usefulness of ChatGPT for their learning. We used a mixed methodology and two instruments for data collection: questionnaires and discussion groups. The sample comprised 150 university students pursuing degrees in Teaching and Social Education. The results show that the majority of students are familiar with the technology, but have not had any formal training at university. They use this tool to complete academic assignments outside the classroom, and they emphasise the need for training in it. Furthermore, following the training, the students highlight an increase in motivation and a positive impact on the development of generic skills such as information analysis, synthesis and management, problem-solving and learning how to learn. Ultimately, this study provides an opportunity to consider the implementation of educational training of this tool at university level in order to ensure its appropriate use.

We present a thermodynamic approach in modeling the evolution of the universe based on a theory that space consists of energy quanta, the spaceons. From wave-particle duality, they can be treated as an ideal gas. The model is similar to the Big Bang but without Inflation. It provides an insight into the nature of dark energy and dark matter, and an explanation for the accelerated expansion of the universe. The universe started from an atomic size volume of spaceons at very high temperature and pressure. Upon expansion and cooling, phase transitions occurred resulting in the formation of fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters due to the action of gravity. From the cooling curve of the universe we constructed a thermodynamic phase diagram of cosmic composition, from which we obtained the correlation between dark energy and the energy of space. Using Friedmann’s equations, our model fits well the WMAP data on cosmic composition with an equation of state parameter, w= -0.7. The dominance of dark energy started at 7.25 x 10⁹ years, in good agreement with BOSS measurements. The expansion of space is attributed to a scalar quantum space field. Dark Matter is identified as a plasma form of matter similar to that which existed during the photon epoch, prior to recombination. The thermodynamics of expansion of the universe was adiabatic and decelerating during the first 7 billion years after the Big Bang; it accelerated thereafter. A negative pressure for Dark Energy is required to sustain the latter. This is consistent with the theory of General Relativity and the law of conservation of energy. We propose a mechanism for the acceleration as due to consolidation of matter forming Dark Energy Stars (DES) and other compact objects. The resulting reduction in gravitational potential energy feeds back energy for the expansion. Space will continue to expand and dark energy will undergo phase transition to a Bose-Einstein condensate, a superfluid form of matter. Self-gravitation can cause a bounce and start a new Big Bang. We show how the interplay of gravitational and space forces leads to a cyclic, maybe eternal, universe.

When we attempt to define life, we tend to refer to individuals, those that are alive. But these individuals might be cells, organisms, colonies... ecosystems? We can describe living systems at different scales. Which ones might be the best ones to describe different selves? I explore this question using concepts from information theory, ALife, and Buddhist philosophy. After brief introductions, I review the implications of changing the scale of observation, and how this affects our understanding of selves at different structural, temporal, and informational scales. The conclusion is that there is no single ``best'' scale for a self, as this will depend on the scale at which decisions must be made. Different decisions, different scales.

While digitization can make the health industry faster and more efficient, there are many financial, social and organizational obstacles and barriers to its implementation. This article offers a systematic review of the main troubles detected from the literature review. Also there is a proposal of new kind of restrictions to pay attention. Finally, its offer an heterodox reading about the problem analyzed.

Information theory has been developed for seventy years with technological applications that have transformed our societies. The increasing ability to store, transmit, and process information is having a revolutionary impact in most disciplines. The goal of this work is to compare the formal approach to information with Buddhist philosophy. Considering both approaches as compatible and complementary, I argue that information theory can improve our understanding of Buddhist philosophy and vice versa. The resulting synthesis leads to a worldview based on information that overcomes limitations of the currently dominating physics-based worldview.

In the present work, we evaluate the prediction capability of six Pedotransfer functions (PTFs), reported in the literature, for the saturated hydraulic conductivity estimations (Ks). We used a database with 900 measured samples obtained from the Irrigation District 023, in San Juan del Rio, Queretaro, Mexico. Additionally, six new PTFs were construct for Ks from clay percentage, bulk density and saturation water content data. The results show, for the evaluated models, that one model present an overestimation for Ks>0.5 cm h-1 values, three models have a underestimation for Ks>1.0 cm h-1 and two models have a good correlation (R2>0.98) but are necessary more than three parameters. Nevertheless, the last two models requires from three to four parameters in order to get the optimization. By other hand, the models proposed in this work have a similar correlation with a less number of parameters: the fit is seen to be much better than using the existing ones, achieving a correlation of R2 = 0.9822 with only one variable and a R2 = 0.9901 when we use two.

The scientific fields of complexity, artificial life (ALife), and artificial intelligence (A.I.) share commonalities: historic, conceptual, methodological, and philosophical. Although their origins trace back to the 1940s birth of cybernetics, they were only able to properly develop as modern information technology became available. In this perspective, I offer a personal (and thus biased) account of the expectations and limitations of these fields, some of which have their roots in the limits of formal systems. I will use interactions, self-organization, emergence, and balance to compare different aspects of complexity, ALife, and A.I. Even when the trajectory of the paper is influenced by my personal experience, the general questions posed (which outweigh the answers) hopefully will be useful to align efforts in these fields toward overcoming --- or accepting --- their limits.

Microgrid is one of the promising green transition technologies that will provide enormous benefit to the seaport, as a solution to the major concerns in this sector, namely energy crisis, economical and environmental pollution. However, finest design of the microgrid is a challenging task considering different objectives, constraints and uncertainties involved. To ensure the optimal operation of the system, determining the right configuration framework and size for each component in the seaport microgrid at the minimum cost is a vital decision at the design stage. This paper aims to design a hybrid system of seaport microgrid with optimally sized component .The selected case study is the Port of Aalborg, Denmark. The proposed grid-connected structure consists of renewable energy sources (photovoltaic system and wind turbines), an energy storage system and cold ironing as seaport’ loads. The architecture is then optimized by utilizing HOMER to meet the maximum load demand by considering a few parameters such as solar global horizontal irradiance, temperature and wind resources. Then, the best configuration framework is analyzed in terms of economic feasibility, energy reliability and environmental impact.