The feasibility of recovering bioactive antioxidants from Phyllantus emblica leaves using ethanol -water mixture (0 – 100%) and heat-assisted extraction technology (HAE-T) was investigated in this present study. To this effect, the process parameter of operating temperature (OT: 30 -50 oC), solid -to-liquid ratio (S:L: 1:20 - 1:60 g/mL) and extraction time (ET: 45 - 180 min) were investigated on the extract total phenolic content (TPC, mg GAE/g d.w), yield (EY, %) and antioxidant activity (μM AAE/g d.w) by employing the Box-Behnken experimental design (BBD) available in response surface methodology (RSM). Multi-objective process optimization using the desirability function algorithm to determine set of process variables that simultaneously optimize process responses of TPC, EY and AA was also investigated. The recovery process was thereafter modeled with BBD-RSM and multi gene genetic programming (MGGP) algorithm and model reliability assessment via Monte Carlo simulation were conducted for the best performing set of models for predicting TPC, EY and AA values. The HPLC characterization of the recovered extract was carried out to ascertain the phenolic compound constituents of the Phyllantus emblica leaf extract. The 50% ethanol solution was found to be the best for the optimal extraction of antioxidants from Phyllantus emblica leaves. The HAE-T was suitable for recovering bioactive extract from Phyllantus emblica leaves and investigated process parameters have impacts on the recovery process. The process parameters that simultaneously gave the optimum EY of 21.6565%, TPC of 67.116 mg GAE/g and AA of 3.68583 µM AAE/g were OT of 41.61 oC, S:L of 1:60 g/mL and ET of 180 min. The HPLC extract profiling revealed that the bioactive constituents present in the recovered extract were betulinic acid, gallic acid, chlorogenic acid, caffeic acid, ellagic acid, and ferulic acid. Both the developed BBD-RSM and evolved MGGP-based models predicted the observed process response of TPC, EY and AA satisfactorily with BBD-RSM models marginally better in their predictions. The reliability results showed that the BBD-RSM models predicted TPC, EY and AA values with high certainty of 99.985%, 97.569% and 98.661%, respectively.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

Background: The link between nocturia and aging male symptoms (AMS) has not been scientifically established. This study aimed to measure the degree of severity of AMS that impact on the health-related quality-of-life (HRQoL) in adult males living with nocturia, and to determine the predictive values of nocturnal factors on AMS. Methods: It is an extended analysis of new data collected by using the Hong Kong Traditional AMS (HK-AMS) scale and Cantonese version of the Pittsburgh Sleep Quality Index (PSQI) in a recently published cross-sectional population-based survey. Results: Of the 781 respondents that have completed the set of questionnaires, 68% and 61% of men living with nocturia reported clinically significant (at moderate-to-severe levels) somato-vegetative and sexual AMS, whereas the prevalence and severity were increased with advancing nighttime voiding frequency. The nocturia-specific QoL (NQoL) score and nocturnal frequency were found to be significant predictive factors for composite, somato-vegetative and sexual AMS, in addition to age, global OSQI score, and certain metabolic diseases. Conclusions: Current findings suggested the inclusion of nocturia when measuring the male-specific HRQoL related to aging.

Background: Most prevalence surveys on nocturia have focused on older populations. This study aimed to measure the nocturia prevalence across the full spectrum of male adults living in Hong Kong, where severity and associated quality-of-life (QoL) were also explored. Methods: A cross-sectional population-based survey was conducted in men aged 18 or above using the ICIQ-NQoL Questionnaire. Results: With 1,239 respondents at age ranged 18-99, the overall nocturia prevalence were found to be 63.0% (ranged 41.6-84.6% at different age groups) and 31.2% (ranged 13.0-56.3% at different age groups), for ≥1 and ≥2 bedtime voiding episodes, respectively. The chance of nocturia was dramatically increased at age 60 or above while both prevalence and voiding frequency were increased with advancing age. About 83% of the nocturia men experienced 1-2 voiding episodes per night, but many of them had self-rated their QoL poor or very poor and indicated moderate-to-high bothersome. Younger men at age 18-39 were found to have high prevalence as 41.6% and almost 30% of them rated poor or very poor QoL. Conclusions: Nocturia was not only affecting the older populations but also caused significant bothersome and negative impacts on QoL in younger males.

The “Crisis of Reproducibility” has received considerable attention both within the scientific community and without. While factors associated with scientific culture and practical practice are most often invoked, I propose that the Crisis of Reproducibility is ultimately a failure of generalization with a fundamental scientific basis in the methods used for biomedical research. The Denominator Problem describes how limitations intrinsic to the two primary approaches of biomedical research, clinical studies and pre-clinical experimental biology, lead to an inability to effectively characterize the full extent of biological heterogeneity, which compromises the task of generalizing acquired knowledge. Drawing on the example of the unifying role of theory in the physical sciences, I propose that multi-scale mathematical and dynamic computational models, when mapped to the modular structure of biological systems, can serve a unifying role as formal representations of what is conserved and similar from one biological context to another. This ability to explicitly describe the generation of heterogeneity from similarity addresses the Denominator Problem and provides a scientific response to the Crisis of Reproducibility.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

A variable annuity is a popular life insurance product that comes with financial guarantees. Using Monte Carlo simulation to value a large variable annuity portfolio is extremely time-consuming. Metamodeling approaches have been proposed in the literature to speed up the valuation process. In metamodeling, a metamodel is first fitted to a small number of variable annuity contracts and then used to predict the values of all other contracts. However, metamodels that have been investigated in the literature are sophisticated predictive models. In this paper, we investigate the use of linear regression models with interaction effects for the valuation of large variable annuity portfolios. Our numerical results show that linear regression models with interactions are able to produce accurate predictions and can be useful additions to the toolbox of metamodels that insurance companies can use to speed up the valuation of large VA portfolios.

Using lightweight fire-rated board (LFRB) presents cost-effective opportunities for various passive fire protection measures. The aim of the project is to develop a LFRB with enhanced fire resistance, acoustic properties, and mechanical properties. These properties were determined using the Bunsen burner, furnace, energy dispersive X-Ray, impedance tube instrument, and Instron universal testing machine. To fabricate the LFRBs, vermiculite and perlite were blended with flame-retardant bind-ers, and four types of LFRBs were produced. A fire test was conducted to compare the fire-resistance performance of the LFRBs with a commercially available flame retardant board. The B2 prototype showed exceptional fire-resistant properties, with a temperature reduction of up to 73.0 °C as compared to the commercially available fire-rated magnesium board. Incorporating nano chicken eggshell into the specially formulated flame-retardant binder preserved the LFRBs’ structural integrity, enabling them to withstand fire for up to 120 minutes with an equilibrium temperature of 92.6 °C. This approach also provided an absorption coefficient of α = 2.0, a high flexural strength of 3.54 MPa, and effective flame retardancy properties with a low oxygen/carbon ratio of 2.60. These results make the LFRBs valuable for passive fire protection applications in the construction and building materials industry.

The basis of the work of electroencephalography (EEG) is the registration of electrical impulses from the brain or some of its individual areas using a special sensor/electrode. This method is used for the treatment and diagnosis of various diseases. The use of wet electrodes in this case does not seem viable, for several well-known reasons. As a result of this, a detailed analysis of modern EEG sensors developed over the past few years is carried out, which will allow researchers to choose this type of sensor more carefully and, as a result, conduct their research more competently. Due to the absence of any standards in the production and testing of dry EEG sensors, the main moment of this manuscript is a detailed description of the necessary steps for testing a dry electrode, which will allow researchers to maximize the potential of the sensor in the various type of research.

Dynamic hedging has been adopted by many insurance companies to mitigate the financial risks associated with variable annuity guarantees. In order to simulate the performance of dynamic hedging for variable annuity products, insurance companies rely on nested stochastic projections, which is highly computationally intensive and often prohibitive for large variable annuity portfolios. Metamodeling techniques have recently been proposed to address the computational issues. However, it is difficult for researchers to obtain real datasets from insurance companies to test metamodeling techniques and publish the results in academic journals. In this paper, we create synthetic datasets that can be used for the purpose of addressing the computational issues associated with the nested stochastic valuation of large variable annuity portfolios. The runtime used to create these synthetic datasets would be about 3 years if a single CPU were used. These datasets are readily available to researchers and practitioners so that they can focus on testing metamodeling techniques.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Background: The pathogenesis of duodenal ulcer has never been explained although the first description of this disease in medical literature appeared in 1817. Marshall et al. concluded that Helicobacter pylori was the most important etiological factor for duodenal ulcer in 1988, but the etiology based on this bacterium is controversial and how the bacterial infection leads to ulceration is presently unknown. Objectives: This study aims to identify the cause of duodenal ulcer, address the controversial issues surrounding Helicobacter pylori, elucidate the roles of gastric acid, and describe the pathological process of duodenal ulceration. Methods: First, a comprehensive systematic review on peptic ulcers (including gastric ulcer and duodenal ulcer) was conducted and the results were summarized. Second, a recently published causal relationship was employed to identify the etiology of peptic ulcers. Third, novel concepts and methods were applied to analyze the existing data on duodenal ulcer. Results: The etiology of duodenal ulcer and the roles of Helicobacter pylori and gastric acid in this disease were identified. The controversies surrounding Helicobacter pylori were addressed, and many characteristics and phenomena/observations of duodenal ulcer were elucidated. The pathological process of duodenal ulceration was described. Conclusion: Existing data accumulated over the past 300 years was sufficient, when analyzed using novel concepts, to understand the pathogenesis of duodenal ulcer. Duodenal ulcer is not an infectious disease caused by the infection of Helicobacter pylori, but a psychosomatic disease triggered by psychological stress. Helicobacter pylori plays a secondary role in only the late phase of duodenal ulceration.

Many parents have difficulty managing childhood asthma. In Hong Kong (HK), while medication is the primary form of treatment, traditional Chinese medicine is another favored option. In addition, HK follows a dual-track healthcare system, which may pose unique experiences for Chinese parents in childhood asthma management. This qualitative descriptive study aimed to explore the experiences of HK Chinese parents in caring for their children with asthma. Methods: Fourteen HK Chinese mothers of children (aged 3-10) suffering from asthma were purposively sampled to participate in individual, semi-structured interviews. A realist approach following conventional content analysis was used to interpret the interviews. Results: The mothers expressed feelings of uncertainty, fear of asthma crises, and searching for ways to cope. These feelings triggered various strategies to control their child’s asthma. As long as the child’s asthma symptoms recurred, the mothers’ distress continued. Their distress was sometimes exacerbated by self-doubt and worries about whether they would receive adequate support from their family and healthcare professionals. Conclusion: Helping parents to understand their limits may help them be more open to varied aspects of their caregiving experiences, and thus to cope better. Psychological interventions together traditional educational training may help to alleviate parents’ psychological difficulties.

The aim of the present study was to assess the efficacy of All Cosmos Industries (ACI) bio-organic and bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) on the paddy yields based on the field trial plots at Langkat, Medan, Indonesia. This application of ACI bio-organic fertilizer (NPK 5/5/5) and ACI bio-chemical (NPK 15/15/15) fertilizer and ACI N-Fixer tests were conducted at the paddy farm at Langkat from May-October 2018. This study employed a factorial randomized complete block design which consisted of two factors, namely: Factor I with four types of fertilizers while Factor II consisted of two paddy varieties (Inpari 30 and Inpari 32). Overall, the filled grains in the ACI treatments are significantly (P< 0.05) higher than those in the control treatments that used Normal Chemical Compound NPK. Overall, total weight per meter² (368-617g) in ACI treatments are also significantly (P< 0.05) higher than those (319-371g) in the control treatments. At harvesting time at 105 days after transplanting, significantly higher (P< 0.05) colony counts (13-15 x 10⁶ CFU/mL) (for ACI treatments), than those (8 x 10⁶ CFU/mL) in the controls positively indicated higher total yields of paddy grains per hectare. It was found that the application of ACI bio-organic and bio-chemical fertilizers and ACI N-Fixer can improve paddy yields of the two rice varieties, between 16.4-38.2% (up to 5.75 MT/ha), in the field trial plots at Langkat. These commercial fertilizers play an imperative role in refining the soil fertility and thereby can increase the yield of rice production. Therefore, it is highly recommended that ACI bio-organic and ACI bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) can be employed to increase the paddy yield in this region.

Cashless payments are so common and popular that people are gradually not taking cash out of the house. But people still need to carry some cash and a couple of debit cards, which increases the risk of people having their cash or cards lost or stolen. The mobile payment method based on scanning codes solves the problem that you don't need to carry cash or cards when you go out, but you still need to enter the APP to scan the code to complete the payment. This report proposes a POS system with NFC technology, enabling people to complete transactions with new payment methods and reducing carrying other payment tools. Therefore, this paper explores the understanding of the proposed system and improves its functionality. The project aims to facilitate quickness for users to complete transactions, that is, near-field communication, using POS systems with received signals for transactions. Data is collected via triangulated research methods from various respondents across Malaysia with statistics and analysis on the proposed solution. The contactless NFC POS solution allows users to interact with the system via smartphone host card emulation application technology to complete transactions and allow people to reduce carrying other payment tools.

In the fast-paced internet world that we live in today, internet technologies and tools that enable us to connect online are rapidly changing and improving. To adapt to the changing environment, many game developers are changing their business models to adjust to this online environment by developing games that are centred around online gaming. As such, the internet demands of consumers such as gamers are increasing because of the need for quality internet connection for optimal gameplay. There are too many factors that can affect online gameplay. Moreover, not all gamers are equipped with the network knowledge and skills to diagnose and troubleshoot any internet issues that may arise during their gameplay session. The main contribution of this research was to gather insights from Malaysian broadband internet consumers, mainly from gamers and general users regarding their opinions of their ISP service experience in gaming, general use and service quality. A 1-click solution is presented as a smart autonomous network monitoring tool that can autonomously monitor, diagnose, and troubleshoot network problems with minimal input from the user. This research was conducted using a mixed-mode research methodology where the participants were asked to fill up a questionnaire regarding the user experience of their Internet Service Provider (ISP), and their perception of the 1 click-automated networking tool for their personal use. It is shown that there is a market demand for a 1 click-automated networking tool as gamers and general users both agree that such a tool would be beneficial to them by improving the internet quality of a network.

This paper investigated reliability modeling for systems subject to dependent competing risks considering that the variation of failure threshold is not considered in most studies on competing failure reliability. Firstly, the variation of degradation quantity under shocks was analyzed, and the variation of threshold was considered on this basis. Secondly, the cumulative degradation under the influence of the random shock process was analyzed. The attractive property of copula is symmetry. Then, A linear Wiener process model is applied to model performance degradation failure, and a multi-performance-degradation correlated-competition model based on a Copula function is constructed, which considers the correlated competition between multiperformance degradation failures. Lastly, the micromotor system is used to analyze the applicability of the proposed model for bivariate instances. demonstrating the rationality and effectiveness of the proposed model.

Superantigens are unconventional antigens which recognise immune receptors outside the usual binding sites e.g. complementary determining regions (CDRs), to elicit a response within the target cell. T-cell superantigens crosslink T-cell receptors and MHC Class II molecules on antigen-presenting cells, leading to lymphocyte recruitment, induction of cytokine storms and T-cell anergy or apoptosis among many other effects. B-cell superantigens, on the other hand, bind immunoglobulin receptors on B-cells affecting opsonisation, IgG-mediated phagocytosis, and drive B-cells into apoptosis. Here, through a review of the structural basis for recognition of immune receptors by superantigens, we show that their binding interfaces share specific physicochemical characteristics when compared with other protein-protein interaction complexes. Given that antibody-binding superantigens have been exploited extensively in industrial antibody purification, these observations could facilitate further protein engineering to optimize the use of superantigens in this and other areas of biotechnology.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

The average working person can spend between 35-60 hours a week in the workplace, making it an influential place for mental well-being while also being a place for socio-economic contribution. Workplace incivility can diminish positive mental health outcomes and negatively impact work engagement through increased social anxiety. To investigate this, 118 working adults aged between 19 to 67 years old in Singapore were recruited for a survey comprising of demographics questions, the Workplace Incivility Scale, Brief DSM-5 Social Anxiety Disorder Severity Scale, Utrecht Work Engagement Scale-9 over the period of November 2022 to April 2023. Correlational, regression and mediation analysis showed workplace incivility scale scores to significantly pre-dict social anxiety after controlling for covariates, supporting our hypothesis that employees exposed to work-place incivility would have higher levels of social anxiety that mediated work engagement after controlling for age and gender. The findings here show workplace incivility to be a possible intervention target for social anx-iety to reduce negative impacts on work engagement in order to improve employee experience and retention for organizations.

We study the brain segmentation by dividing the brain into multiple tissues. Given possible brain segmentation by deep, machine learning can be efficiently exploited to expedite the segmentation process in the clinical practice. To accomplish segmentation process, a MRI and tissues transfer using generative adversarial networks is proposed. Given the better result, we propose the transfer model using GAN. For the case of the brain tissues, white matter (WM), gray matter (GM) and cerebrospinal fluid (CSF) are segmented. Empirical results show that this proposed model significantly improved segmentation results compared to the stat-of-the-art results. Furthermore, a dice coefficient (DC) metric is used to evaluate the model performance.

This paper introduces a fusion convolutional architecture for efficient learning of spatio-temporal features in video action recognition. Unlike 2D CNNs, 3D CNNs can be applied directly on consecutive frames to extract spatio-temporal features. The aim of this work is to fuse the convolution layers from 2D and 3D CNNs to allow temporal encoding with fewer parameters than 3D CNNs. We adopt transfer learning from pre-trained 2D CNNs for spatial extraction, followed by temporal encoding, before connecting to 3D convolution layers at the top of the architecture. We construct our fusion architecture, semi-CNN, based on three popular models: VGG-16, ResNets and DenseNets, and compare the performance with their corresponding 3D models. Our empirical results evaluated on the action recognition dataset UCF-101 demonstrate that our fusion of 1D, 2D and 3D convolutions outperforms its 3D model of the same depth, with fewer parameters and reduces overfitting. Our semi-CNN architecture achieved an average of 16 – 30% boost in the top-1 accuracy when evaluated on an input video of 16 frames.

The target of an antibody plays a significant role in the success of antibody-based therapeutics and diagnostics, and to an extent, that of vaccine development. This importance is focussed on the target binding site – epitope, where epitope selection as a part of design thinking beyond traditional antigen selection using whole cell or whole protein immunisation can positively impact success. With purified recombinant protein production and peptide synthesis to display limited/selected epitopes, intrinsic factors that can affect the functioning of resulting antibodies can be more easily selected for. Many of these factors stem from the location of the epitope that can affect accessibility of the antibody to the epitope at a cellular or molecular level, direct inhibition of target antigen activity, conservation of function despite escape mutations, and even non-competitive inhibition sites. Through the incorporation of novel computational methods for predicting antigen changes to model-informed drug discovery and development, superior vaccines and antibody-based therapeutics or diagnostics can now be more easily designed to mitigate failures. With detailed examples, this review highlights the new opportunities, factors and methods of predicting antigenic changes for consideration in sagacious epitope selection.

As the world faces unprecedented environmental challenges and the rapid advancements of artificial intelligence (AI), it is crucial for universities to adapt their chemistry education to remain relevant and contribute to sustainability and the United Nations' Sustainable Development Goals (SDGs). This report offers critical insights into the development of university chemistry education over the next 10-20 years, forecasts its development over the next 10-20 years, and offers recommendations for the Ministry of Education and universities to ensure the continued relevance of chemistry programs in the face of AI.

(1) Background: To identify the association between the presence or absence of raphe and aortic valve dysfunction as well as the presence of aortopathy in patients with bicuspid aortic valve (BAV); (2) Methods: This retrospective study enrolled 312 participants (mean [SD] age, 52.7 [14.3] years; 227 men [72.8%]) with BAV. The BAVs were divided into those with presence (raphe+) or absence (raphe-) of raphe. Valvular function was classified as normal, aortic regurgitation (AR), or aortic stenosis (AS) using TTE. The pattern of BAV aortopathy was determined by the presence of dilatation at the sinus of Valsalva and the middle ascending aorta using CCT.; (3) Results: BAVs with raphe+ had a higher prevalence of AR (148 [79.5%] vs. 48 [37.8%], P < .001) but a lower prevalence of AS (90 [48.6%] vs. 99 [78.0%], P < .001) compared with those with raphe-. The types of BAV aortopathy were significantly different (P = 0.021) according to those with BAV-raphe+ and BAV-raphe-.; (4) Conclusions: The presence of a raphe was significantly associated with a higher prevalence of AR but a lower prevalence of AS and combined dilatation of the aortic root and middle ascending aorta. The presence of raphe was an independent determinant of AR.

The negative impact of the modern-day lifestyle on the environment is aggravated during the COVID-19 pandemic through the increased use of single-use plastics from food takeaways to medical supplies. Similarly, the closure of food outlets and disrupted supply chains have also resulted in significant food wastage. As the pandemic rages on, the aggravation of increased waste becomes an increasingly urgent problem that threatens the biodiversity, ecosystems, and human health worldwide through pollution. While there are existing methods to deal with the organic and plastic waste, many of the solutions also cause additional problems. Increasingly proposed as a natural solution to man-made unnatural problems, there are insect solutions for dealing with the artificial and organic waste products towards a circular economy, making the use of natural insect solutions commercially sustainable. This review discusses the findings and how some of these insects, particularly the Hermetia illucens, Tenebrio molitor, and Zophobas morio, can play an increasing important role in food and plastics, with a focus on the latter.

: Soil free living nematodes community composition was compared for five agro-management systems in a basaltic soil. The sites differed in their long-term management system and were designated as organic farming (OM), conventional (MI), natural pasture (NP), foliage farming (FF) and open field (OF). The effect of five diverse land use types in vineyard growth in basaltic soils on soil free living nematodes, density, diversity, and functionality in the plant rhizosphere was examined. We found 22 families, 42 genera of which only 14 genera were present in all soil samples, three bacteria feeders, 4 fungi feeders, 3 omnivores-predators and 4 plant parasites, in the soil collected from the five sampling sites. The organic and conventional managements were found to influence soil free living nematode community and its trophic composition. The higher abundance of bacteria feeders included the Cephalobidae and Panagrolaimidae families. The fungi feeders included the Anguinidae and Aphelenchidae families. Ominvores-predators included the Aprocelaimidae and Qudsianematidae, and the plant parasites included the Anguinidae (genus Anguina), Nothotylenchidae and Tylenchidae families. The changes in plant parasite nematodes were one of the main pests in the below-ground rhizosphere biome. Promoting the bacterial community could be a beneficial and promising way for a considerable increase in organic management.

We present the results of a twofold experimental and computational study of (0001) GaN/AlN multilayers forming pseudomorphic superlattices. High-Resolution Transmission Electron Microscopy (HRTEM) shows that heterostructures with GaN Quantum Wells (QW) four c-lattice parameters thick are misfit-dislocation free. Accurate structural data are extracted from HRTEM images via a new methodology optimizing the residual elastic energy stored in the samples. Total energy calculations are performed with several models analogous to the experimental QWs with increasing thicknesses of GaN, whereas this of the AlN barrier is kept fixed at n=8 c-lattice parameters. With vanishing external stresses, minimum energy configurations of the studied systems correspond to different strain states. Linear elasticity accurately yields the corresponding lattice parameters, suppressing the need for on-purpose total energy calculations. Theoretically justified parabolic fits of the excess interfacial energy yield the values of interfacial stress and elastic stiffness as functions of the GaN QW thickness. Total species-projected densities of states and gap values extracted therefrom allow deciphering the effect of the evolving strain on the electronic structure of the superlattice. It is found that the gap energy decreases linearly with increasing the strain of the QW. These results are briefly discussed in the light shed by previous works from the literature.

This paper is motivated by spatio-temporal pattern in the occurrence of Leishmaniasis in Afghanistan and the relatively high number of zero counts. We hold the view that correlations that arise from spatial and temporal sources are inherently distinct. Our method decouples these two sources of correlations, there are at least two advantages in taking this approach. First, it circumvents the need to inverting a large correlation matrix, which is a commonly encountered problem in spatio-temporal analyses. Second, it simplifies the modelling of complex relationships such as anisotropy, which would have been extremely difficult or impossible if spatio-temporal correlations were simultaneously considered. We identify three challenges in the modelling of a spatio-temporal process: (1) accommodation of covariances that arise from spatial and temporal sources; (2) choosing the correct covariance structure and (3) extending to situations where a covariance is not the natural measure of association. Moreover, because the data covers a period that overlaps with the US invasion of Afghanistan, the high number of zero counts may be the result of no disease incidence or lapse of data collection. To resolve this issue, a model truncated at zero built on a foundation of the generalized estimating equations was proposed.

Parkinson’s disease (PD) is characterized by motor deficits and a wide variety of non-motor symptoms. The age of onset, rate of disease progression and the precise profile of motor and non-motor symptoms display considerable individual variation. Neuropathologically, the loss of substantia nigra dopaminergic neurons is a key feature of PD. The vast majority of PD patients exhibit alpha-synuclein aggregates in several brain regions, but there is also great variability in the neuropathology between individuals. While the dopamine replacement therapies can reduce motor symptoms, current therapies do not modify the disease progression. Numerous clinical trials using a wide variety of approaches have failed to achieve disease modification. It has been suggested that the heterogeneity of PD is a major contributing factor to the failure of disease modification trials, and that it is unlikely that a single treatment will be effective in all patients. Precision medicine, using drugs designed to target the pathophysiology in a manner that is specific to each individual with PD, has been suggested as a way forward. PD patients can be stratified according to whether they carry one of the risk variants associated with elevated PD risk. In this review we assess current clinical trials targeting two enzymes, leucine-rich repeat kinase 2 (LRRK2) and glucocerebrosidase (GBA), which are encoded by two most common PD risk genes. Because the details of the pathogenic processes coupled to the different LRRK2and GBA risk variants are not fully understood, we ask if these precision medicine-based intervention strategies will prove “precise“ or “personalized“ enough to modify the disease process in PD patients. We also consider at what phases of the disease that such strategies might be effective, in light of the genes being primarily associated with the risk of developing disease in the first place, and less clearly linked to the rate of disease progression. Finally, we critically evaluate the notion that therapies targeting LRRK2 and GBA might be relevant to a wider segment of PD patients, beyond those that actually carry risk variants of these genes.

Porous tantalum (Ta) is a promising biomaterial and has been applied in orthopedics and dentistry for nearly two decades. The high porosity and interconnected pore structure of porous Ta promise fine bone ingrowth and new bone formation within the inner space, which further guarantee rapid osteointegration and bone-implant stability in long term. Porous Ta has high wettability and surface energy that can facilitate adherence, proliferation and mineralization of osteoblasts. Meanwhile, low elastic modulus and high friction coefficient of porous Ta can effectively avoid stress shield effect, minimize marginal bone loss and ensure primary stability. Accordingly, the satisfactory clinical application of porous Ta based implants or prostheses are mainly derived from its excellent biological and mechanical properties. With the advent of additive manufacturing, personalized porous Ta based implants or prostheses have shown their clinical value in the treatment of individual patient who need specially designed implant or prosthesis. In addition, many modification methods have been introduced to enhance the bioactivity and antibacterial property of porous Ta with promising in vitro and in vivo research results. In any case, choosing suitable patients is of great importance to guarantee surgical success after porous Ta insertion.

2014 marked the first emergence of avian influenza A(H5N8) in Jeonbuk Province, South Korea, which then quickly spread worldwide. In the midst of the 2020-21 H5N8 outbreak, it spread to domestic poultry and wild waterfowl shorebirds, leading to the first human infection in Astrakhan Oblast, Russia. Despite being clinically asymptomatic and without direct human-to-human transmission, the World Health Organisation stressed the need for continued risk assessment given the nature of Influenza to reassort and generate novel strains. Given its promiscuity and spread to humans, the urgency to understand the mechanisms of possible species jumping to avert disastrous pandemics is increasing. Addressing the epidemiology of H5N8 and its mechanisms of species jumping and its implications, mutational and reassortment libraries can potentially be built, allowing them to be tested on various models complemented with deep-sequencing and automation. With the knowledge on mutational patterns, cellular pathways, drug resistance mechanisms and effects of host proteins can allow better preparedness against H5N8 and other influenza A viruses.

Visualising textual content could be helpful to professionals as well as amateurs across several fields. However, training a text-to-image generator in the mainstream domain requires large amounts of paired text-image and data, which is too expensive to collect since labeling millions of images and videos can be tiresome. GANs like StackGAN and StyleGAN can be considered as solutions to generate images from text. But the images generated may be of low accuracy and resolution, and the entire processing can be highly time-consuming. Moreover, image generation is a notion that is still being researched. Hence, the process of developing a Video Generation model necessitates substantial research. Despite the need for such a model, modern technology has lagged behind the solutions to this problem. This proposal suggests combining two methods, Text modification for Action Definition (TexAD) and SeQuential Image Generation for Video Synthesis (SQIGen). The proposed solution synthesises a sequence of images from textual information feeds and combines these images to create a video. TexAD uses Natural Language Processing and Deep Learning techniques to process, classify and modify text data. SQIGen is an extension of the VQGAN+CLIP neural network architecture that generates a sequence of images from the modified text data

In this paper we propose the generation of synthetic small and more sophisticated molecule structures that optimize the binding affinity to a target (ASYNT-GAN). To achieve this we leverage on three important achievements in A.I.: Attention, Deep Learning on Graphs and Generative Adversarial Networks. Similar to text generation based on parts of text we are able to generate a molecule architecture based on an existing target. By adopting this approach, we propose a novel way of searching for existing compounds that are suitable candidates. Similar to question and answer Natural Language solutions we are able to find drugs with highest relevance to a target. We are able to identify substructures of the molecular structure that are the most suitable for binding. In addition, we are proposing a novel way of generating the molecule in 3D space in such a way that the binding is optimized. We show that we are able to generate compound structures and protein structures that are optimised for binding to a target.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

For automobile insurance, it has long been implied that when a policyholder made at least one claim in the prior year, the subsequent premium is likely to increase. When this happens, the policyholder may seek to switch to another insurance company to possibly avoid paying for a higher premium. In such situations, insurers may be faced with the challenges of policyholder retention by keeping premiums low in the face of competition. In this paper, we seek to find empirical evidence of possible association between policyholder switching after a claim and the associated change in premium. In accomplishing this goal, we employ the method of association rule learning, a data mining technique that has its origins in marketing for analyzing and understanding consumer purchase behavior. We apply this unique technique in two stages. In the first stage, we identify policyholder and vehicle characteristics that affect the size of the claim and resulting change in premium regardless of policy switch. In the second stage, together with policyholder and vehicle characteristics, we identify the association among the size of the claim, the level of premium increase and policy switch. This empirical process is often challenging to insurers because they are unable to observe the new premium for those policyholders who switched. However, we used a 9-year claims data for the entire Singapore automobile insurance market that allowed us to track information before and after the switch. Our results provide evidence of a strong association among the size of the claim, the level of premium increase and policy switch. We attribute this to the possible inefficiency of the insurance market because of the lack of sharing and exchange of claims history among the companies.

Background: COVID-19 booster uptake remained poor among healthcare workers (HCW) despite evidence of improved immunity against Delta and Omicron variants. While most studies used a questionnaire to assess hesitancy, this study aimed to identify factors affecting true booster hesitancy by examining actual vaccine uptake across time. Method: COVID-19 vaccination database records among HCW working at 7 Singaporean public primary care clinics between January to December 2021 were extracted, with gender, profession, place of practice, vaccination type and dates. Time to booster was calculated from the date of vaccination minus date of eligibility. Chi-square test was used to compare relationship between 1st dose and booster hesitancy, Kaplan-Meier method and Log-rank test were adopted to evaluate differences in cumulative booster uptake. Multivariate cox regression was used to investigate predictors for timely booster vaccination. Vaccination rate was charted across time and corroborated with media releases pertaining to legislative changes. Results: 877 of 891 (98.9%) primary care HCW were fully vaccinated, 73.8% of eligible HCW had taken the booster. HCW were less booster hesitant [median 16 (5-31.3) days] compared to the 1st dose [median 39 (13-119.3) days]. 1st dose hesitant HCW were more likely to be booster hesitant (OR=3.66, 95%CI 2.61-5.14). Adjusting for sex, workplace and time to 1st dose, ancillary (HR=1.53, 95%CI 1.03-2.28), medical (HR=1.8, 95%CI 1.18-2.74) and nursing (HR=1.8, 95%CI 1.18-2.37) received boosters earlier compared with administrative staff. No temporal relationship was observed between booster uptake, legislative changes and COVID-19 infection numbers. Conclusion: Vaccine hesitancy among HCW had improved from booster to 1st dose, with timely booster vaccination among medical and nursing staff. Tailored education, risk messaging and strategic legislation might help to reduce delayed booster vaccination.

(1) In recent ten years, with the fast development of digital and engineering manufacturing technology, additive manufacturing has already been more and more widely used in the field of dentistry, from the first personalized surgical guides to the latest personalized restoration crowns and root implants. (2) Especially, the bioprinting of teeth and tissue is of great potential to realize organ regeneration and finally improve the life quality. (3) In this review paper, we firstly presented the workflow of additive manufacturing technology. Then we summarized main applications and recent research progresses of additive manufacturing in dentistry. (4) Lastly, we sketched out some challenges and future directions of additive manufacturing technology in dentistry.

With the development of deep learning, the Super-Resolution (SR) reconstruction of microscopic images has improved significantly. However, the scarcity of microscopic images for training, the underutilization of hierarchical features in original Low Resolution (LR) images, and the high-frequency noise unrelated with the image structure generated during reconstruction process are still challenges in the Single Image Super-Resolution (SISR) field. Faced with these issues, we first collected sufficient microscopic images through Motic, a company engaged in the design and production of optical and digital microscopes, to establish a dataset. Secondly, we proposed a Residual Dense Attention Generative Adversarial Network (RDAGAN). The network comprises a generator, an image discriminator, and a feature discriminator. The generator includes a Residual Dense Block (RDB) and a Convolutional Block Attention Module (CBAM), focusing on extracting the hierarchical features of the original LR image. Simultaneously, the added feature discriminator enables the network to generate high-frequency features pertinent to the image’s structure. Finally, we conducted experimental analysis and compared our model with six classic models. Compared with the best model, our model improved PSNR and SSIM by about 1.5dB and 0.2, respectively.

Augment reality (AR) is crucial for immersive human-computer interaction (HCI) and vision of artificial intelligence (AI). Labeled data drove object recognition in AR. However, manual annotating data is expensive and labor-intensive, and furthermore, scanty labeled data limits the application of AR. Aiming at solving the problem of insufficient training data in AR object recognition, an automated vision data synthesis method called BAGAN is proposed in this paper based on the 3D modeling and GAN algorithm. Our approach has been validated to have better performance than other methods through image recognition task on natural image database ObjectNet3D. This study can shorten the algorithm development time of AR and expand the application scope of AR, which is of great significance to immersive interactive systems.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

Self-administered pre-participation screening for physical activity (PA) requires an instrument that should be easily used and identify individuals at high risk. The Physical Activity Readiness Questionnaire (PAR-Q+) has been used for many years. Its ease of use and ability to identify those not fit to undergo PA has not been assessed. This study was to determine the rates of the PAR-Q+ in identifying adults who may not be fit for moderate or intense PA and obtain feedback on the use of this tool. A public on-line voluntary survey on the PAR-Q+ was carried out obtaining participants’ bio-characteristics, them completing the PAR-Q+ form and providing feedback. With 1019 participants, about 57.8% engaged in at least 150 minutes of PA weekly. This decreased with increasing number of co-morbidities. Increasing age was associated with more co-morbidities. About 33.1% of the participants using the PARQ+ would have required further medical evaluation. Only 3 of the 7 main PAR-Q+ questions were easily understood. Difficulties were encountered with 39 of the 44 follow-up questions, especially amongst those with co-morbidities. The large number of technical terms was also a source of concern. The PAR-Q+ would need extensive simplification before it may be recommended for use.

Background: A prospective study was conducted to follow-up how the living lifestyle of hikikomori could change the social, mental and physical health profile. Methods: A cohort consisted of 104 young people living as Hikikomori were interviewed at baseline, 6 months and 12 months by using the same set of questionnaires and anthropometric measurements. Results: Besides the high attrition of 30% in wave 2 and 25% in wave 3, almost half of the participants have recovered from hikikomori by returning to the workforce in society. The three domains of health profile of hikikomori were significantly improved over the follow-up period by: 1) increasing the social network scores from 2.791.80 to 3.091.87, 2) decreasing the perceived stress scores from 21.185.87 to 20.115.79, and 3) reducing blood pressure levels from 118/75 to 115/71 and waist-to-hip ratios. Those variables were also predictable by lifestyle living with the hikikomori according to the Generalized Estimating Equation analysis, whereas the participants of current study had increased the practice of moderate-intensity exercises. Conclusion: Social work intervention was effective in helping the recovery of hikikomori while physical assessments followed by encouragement from social workers to do more exercises might enhance their awareness in health modification towards a better health.

Control charts have been widely used for monitoring process quality in manufacturing and play an important role in triggering a signal in time when detecting a change in process quality. Many control charts in literature assume that the in-control distribution of the univariate or multivariate process data is continuous and not categorical. This research develops two exponentially weighted moving average (EWMA) proportion control charts for monitoring a process with multinomial proportions when considering both large and small sample sizes. For a large sample size , the charting statistic depends on the well-known Pearson χ2 statistic, and the control limit of the EWMA proportion chart is determined by an asymptotical chi-square distribution. For a small sample size, we derive the exact mean and variance of the Pearson χ2 statistic. Hence, the exact EWMA proportion chart is determined. The proportion chart can also be applied to monitor the distribution-free continuous multivariate process as long as each categorical proportion associated with specification limits of each quality variable is known or estimated. Lastly, we investigate the detection performance of the proposed EWMA proportion chart by numerical analyses. Real data analysis demonstrates the beneficial application of the proposed EWMA proportion charts.

Facial recognition systems are widely used systems around the globe. Their applications in real world scenarios like law enforcement, surveillance, ID card identification, information security, access control and many more has made them very important in today’s world. These systems have shown promising results and excellent performance; however, these systems need tremendous number of facial images for training before they are implemented in the real-world scenarios. The problem arises when we face lack of training images due to which the performance of such systems decreases exponentially. The problem becomes even worse when there is only one image per subject for training our facial recognition system, the probe image might contain variation like illumination, expression and disguise which are hard to be accurately recognized. Generative models have achieved great success for handling the lack of training data by generating synthetic data that resembles the original data. We have created a new method by fine tuning the basic Conditional Generative Adversarial Network (CGAN) to generate synthetic facial images provided only single image per subject. These synthetic facial images contain six variations that are smile, anger, stare, illumination and disguise. We increased the size of the dataset and then applied a convolutional neural network for facial recognition, which improved the accuracy of our system from 0.76 to 0.99.

Active magnetic bearings have higher efficiency than other bearings because there is no physical contact. However, this benefit is mitigated by the addition of electrical power consumption. It is therefore important for magnetic bearings to have efficient power electronics. Gallium nitride-based transistors are a relatively new form of transistor which have shown to be more efficient than MOSFETs. There is an insufficient body of literature in the area of application of these transistors for magnetic levitation. This work presents a simple 1 degree-of-freedom voltage controlled levitation experiment in which levitation is achieved with both a gallium nitride transistor and a MOSFET.
Voltage losses and current consumption are measured when using each transistor during levitation. In particular, transients during open-to-closed and closed-to-open states are measured for PWM pulsing. It is found that the
gallium nitride transistor is superior in both switching time and efficiency in situ for magnetic levitation.

The effect of growth temperature and precursor flows on the doping level and surface morphology of Ge-doped GaN layers was researched. The results show that germanium is more readily incorporated at low temperature, high growth rate and high V/III ratio, thus revealing a similar behavior to what was previously observed for indium. V-pit formation can be blocked at high temperature but also at low V/III ratio, the latter of which however causing step bunching.

In recent years, with the increasing research and development of the LED industry which contains GaN, it is expected that there will be a large amount of related wastes in the future. Especially the gallium has extremely high value of economic, therefore, it is necessary to establish the recycling system of the GaN waste. However, GaN is a direct-gap semiconductor and with high energy gap, high hardness, and high melting point make it difficult to recycle. Therefore, this study will analyze the physical characteristics of LED wastes containing GaN and carry out various leaching method to leach the valuable metals from the waste optimally. Different acids are used to find out the best reagent for leaching the gallium. Different experimental parameters are discussed such as the effect of the different acid agents , concentration, pressure, solid-liquid mass ratio, temperature, and time which influence the leaching efficiency of the gallium. In this study, various leaching methods which effect the leaching efficiency of the gallium are compared and the advantages and disadvantages are discussed. Finally, pressurized acid leaching method is preferred to leach the GaN waste, and hydrochloric acid is used as the leaching solution because of its better leaching efficiency of gallium. Eventually, the leaching efficiency of the gallium can reach to 98%.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Compressed Sensing (CS) MRI has shown great potential in enhancing time efficiency. Deep learning techniques, specifically Generative Adversarial Networks (GANs), have emerged as potent tools for speedy CS-MRI reconstruction. Yet, as the complexity of deep learning recon-struction models increases, this can lead to prolonged reconstruction time and challenges in achieving convergence. In this study we present a novel GAN-based model that delivers superior performance without escalating model complexity. Our generator module, built on the U-net architecture, incorporates dilated residual (DR) networks, thus expanding the network's receptive field without increasing parameters or computational load. At every step of the downsampling path, this revamped generator module includes a DR network, with the dilation rates adjusted according to the depth of the network layer. Moreover, we have introduced a channel attention mechanism (CAM) to distinguish between channels and reduce background noise, thereby fo-cusing on key information. This mechanism adeptly combines global maximum and average pooling approaches to refine channel attention. We conducted comprehensive experiments with the designed model using public domain MRI datasets of the human brain. Ablation studies af-firmed the efficacy of the modified modules within the network. Compared to other relevant models, our proposed model exhibits exceptional performance, achieving not only excellent sta-bility but also outperforming other networks in terms of Peak Signal-to-Noise Ratio (PSNR) and Structural Similarity Index (SSIM). The model presents a promising pathway for enhancing the efficiency and quality of CS-MRI reconstruction.

In recent years, land supply in Hong Kong has fallen sharply and fails to keep pace with the growth of population and number of households. Land shortage becomes urgent and dire. With the inadequate provision of residential land, housing supply is also adversely affected.Insufficient housing supply leads to surging property and rental price in the private market. According to the Rating and Valuation Department (RVD), the overall private domestic price index peaked in June 2017 at 336.1. Keen housing demand is also observed in the private rental market. RVD statistics showed that the domestic rental index also reached the peak at 183.6 in June 2017 and the vacancy rate of about 3.8% as at the end-2016, which is much lower than the average vacancy rate of 5% from 1996 to 2015 (Development Bureau, 2017).In addition, there is soaring housing demand in public housing. As at the end-December 2021, the average waiting time for general applicants was 5.7 years, which is nearly double of the Housing Authority’s target for providing the first flat offer to general applicants at around three years on average (Housing Authority, 2021). Identifying and securing sufficient land to meet both current and anticipated pressing housing demand becomes a key challenge of the government. In the light of this, the government has established a dedicated task force (Task Force on Land Supply) in September 2017 and appointed 30 professionals from different disciplines, such as planning, engineering, academia and think tank, to take a Marco-review on the land supply sources, look for feasible options as well as consider the pros and cons of various options. 18 land supply options were worked out for the public to make choices in the public engagement exercise. Among the 18 choices, the development area on the Periphery of Country Parks was regarded as one of the land supplies sources. This option does not only include the Hong Kong Housing Society’s studies on developing Two Pilot Areas on the Periphery of Tai Lam and Man On Shan Country Parks, but also include developing more areas on the periphery of Country Parks. The proposed option received overwhelming attention from the public and aroused debates in various perspectives. Its ecological value, recreational value, financial viability and even legitimacy were discussed. However, spatial analysis on the suitability of having residential development in Country Parks has not been conducted. Therefore, in this study, multi criteria GIS analysis is conducted to evaluate the geographic suitability of Hong Kong Country Parks for residential purpose with the consideration of various criteria.

The copper end paste used in multilayer ceramic capacitors sintered in nitrogen atmosphere will lead to carbon residue of organic vehicle, which will lead to the reduction of electrode conduc-tivity and high scrap rate. With an attempt to leave no residue in the sintering, the compatibility of solvents and thickeners should be improved because it has an important influence on the hi-erarchical volatilization and carbon residue of organic vehicles. In this work, the volatility of different solvents was compared and several solvents were mixed in a definite proportion to prepare an organic vehicle with polyacrylate resins. The hierarchical volatility and solubility parameters of mixed solvents were adjusted effectively by changing proportions of different components, the thermogravimetric curves of resins and organic vehicles were measured by thermogravimetric analyzer, the effect of solubility parameter on the dissolvability of resins in the solvent and the residual of organic vehicles were studied. Results showed that the hierar-chical volatilization of solvents can be obtained by mixing different solvents; the intrinsic vis-cosity of the organic vehicle is higher and the thermal decomposition residue of polyacrylate resins is lower when the solubility parameters of mixed solvents and polyacrylate resins are closer. The low residual sintering of organic vehicles can be achieved by using the mixed solvent with hierarchical volatility and approximate solubility parameters as resins.

In the present work, diamond films have been grown on GaN-on-Sapphire substrates by chemical vapor deposition (CVD) with the addition of nitrogen to the standard H2/CH4 precursor recipe. Diamond on GaN materials processing is not straight-forward, as GaN is susceptible to a quasi-pure hydrogen CVD plasma etching. 1%, 3% and 5% N2 gas was gradually added to the H2 gas with fixed 6% CH4 in the recipe to promote the growth of diamond nanocrystals. Different types of microstructures were produced, with addition of nitrogen to the precursor gas recipe. Nitrogen gas changes the diamond film microstructure from faceted to spherical grains, with signs of GaN etching. The sp3 bonded diamond film produced by nitrogen addition was found to be co-deposited along with a considerable amount of other non-diamond carbon phases (D - disordered graphite, G - crystalline graphite, TPA - trans-polyacetylene) and qualitatively all the diamond films were 50% pure (Raman peak ratio Isp3 / ID). The FWHM of the sp3 carbon Raman peak was calculated to be 6.5 cm-1, when there was no nitrogen gas in the precursor recipe, which deteriorates to a large extent after successive addition of N2. Fourier transform infrared spectroscopy (FTIR) showed a strong presence of the nitrogen related defects (peak positions at 1190 and 1299 cm-1) inside the nanocrystalline diamond (NCD) films grown with N2 addition. GaN layer etching from the base substrate by the CVD plasma was clearly evidenced by energy dispersive X-ray spectra (EDS) of the deposited films. Al elemental EDS peaks from the base sapphire substrate were observed for the films grown with nitrogen addition, but no Ga EDS peaks were detected. X-ray diffraction (XRD) micrographs further supported the enhanced GaN etching phenomenon. Nitrogen addition was thus found to be detrimental for growing CVD diamond films over GaN surfaces. The electrical resistivity of the uncoated GaN was initially measured to be 22.2 Ω-cm. However, the resistivity rose to 1.59×106 Ω-cm after the nitrogen assisted film deposition; due to the GaN etching - thereby exposing the underlying insulating sapphire substrate.

To realize fast and effective synthetic aperture radar (SAR) deception jamming, a high-quality SAR deception jamming template library can be generated by performing sample augmentation on SAR deception jamming templates. However, current sample augmentation schemes of SAR deception jamming templates face certain problems. First, the authenticity of templates is low due to the lack of speckle noise. Second, the generated templates have low similarity to the target and shadow areas of the input templates. To solve these problems, this study proposes a sample augmentation scheme based on generative adversarial networks, which can generate a high-quality library of SAR deception jamming templates with shadows. The proposed scheme solves the two aforementioned problems from the following aspects. First, the influence of the speckle noise is considered in the network to avoid the problem of reduced authenticity in generated images. Second, a channel attention mechanism module is used to improve the network's learning ability of shadow features, which improves the similarity between the generated template and the shadow area in the input template. Finally, the proposed scheme and the SinGAN scheme are compared regarding the equivalent numbers of looks and the structural similarity between the target and shadow in the sample augmentation results. The comparison results demonstrate that, compared to the templates generated by the SinGAN scheme, those generated by the proposed scheme have targets and shadow features similar to those of the original image, and can incorporate speckle noise characteristics, resulting in higher authenticity, which helps to achieve fast and effective SAR deception jamming.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

InGaN/GaN samples grown on c-plane sapphire substrate with different In concentrations by metal organic chemical vapor deposition are demonstrated. The subsequent capping GaN layer growth opens a possibility for dislocation reduction due to the lateral strain relaxation in growth geometry. We present the further growth optimization and innovative characterization of InGaN layers overgrown on different structures with varying In concentrations. The photoelectrical and optical properties of the InGaN layers with or without capping GaN layer were investigated by time-resolved picosecond transient grating and temperature dependence photoluminescence. We note a 10-fold increase in carrier lifetime in the InGaN layers when the sample structure changes from PIN to single InGaN layer.

Contrary to optical images, Synthetic Aperture Radar (SAR) images are in different electromagnetic spectrum where the human visual system is not accustomed to. Thus, with more and more SAR applications, the demand for enhanced high-quality SAR images has increased considerably. However, high-quality SAR images entail high costs due to the limitations of current SAR devices and their image processing resources. To improve the quality of SAR images and to reduce the costs of their generation, we propose a Dialectical Generative Adversarial Network (Dialectical GAN) to generate high-quality SAR images. This method is based on the analysis of hierarchical SAR information and the “dialectical” structure of GAN frameworks. As a demonstration, a typical example will be shown where a low-resolution SAR image (e.g., a Sentinel-1 image) with large ground coverage is translated into a high-resolution SAR image (e.g., a TerraSAR-X image). Three traditional algorithms are compared, and a new algorithm is proposed based on a network framework by combining conditional WGAN-GP (Wasserstein Generative Adversarial Network - Gradient Penalty) loss functions and Spatial Gram matrices under the rule of dialectics. Experimental results show that the SAR image translation works very well when we compare the results of our proposed method with the selected traditional methods.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

Deep learning dominates automated animal activity recognition (AAR) tasks due to the high performance on large-scale datasets. However, constructing centralised data across diverse farms raises data privacy issues. Federated learning (FL) provides a distributed learning solution to train a shared model by coordinating multiple farms (clients) without sharing their private data. Whereas directly applying FL to AAR tasks often faces two challenges: client-drift during local training and gradient conflicts during global aggregation. In this study, we develop a novel FL framework called FedAAR to achieve AAR with sensor data. Specifically, we devise a prototype-guided local update module to alleviate the client-drift issue, which introduces global prototypes as shared knowledge to force clients to learn consistent features. To reduce gradient conflicts between clients, we design a gradient refinement-based aggregation module to eliminate conflicting components between client gradients during global aggregation, thereby improving the agreement between clients. Experiments are conducted on a public dataset to verify FedAAR’s effectiveness, which consists of 87,621 2-s motion data. The results demonstrate that FedAAR outperforms state-of-the-arts, with precision (75.23%), recall (75.17%), F1-score (74.70%), and accuracy (88.88%), respectively. The ablation experiments also show FedAAR’s robustness against various factors (i.e., different data sizes, communication frequency, and client numbers).

Colorectal cancer (CRC) is the third most common cancer, with rising incidence due to lifestyle and diet. 40% of CRC cases are found to have KRAS mutations. In this study, we investigate the survival outcome of metastatic Colorectal cancer mCRC) patients in Brunei Darussalam restrospectively. Chi-squared test was used to compare the survival outcomes of mCRC patients, and Mann-Whitney U test was used to compare the median ages of both groups. Kaplan-Meier survival curves were drawn and logrank test was used to compare the survival outcome between two groups. There was a total of 105 patients with stage IV CRC being treated during the study period. 81.6% (n=62) of mCRC patients were found to have the primary tumours on the left side of the colon. 19 of these 26 (73.1%) mutant KRAS mCRC patients died, while 23 of 50 (46.0%) wild-type KRAS mCRC patients died at the end of the study period, contributing to death rates of 45.2% and 54.8%, correspondingly. 30.3% (n=23) of the study population had a single metastatic site detected (either liver, or lung or any other organs), while 69.7% (n=53) of the 76 mCRC patients had two (double) or more metastatic sites. 69.2% (n=18) and 30.8% (n=8) of the mutant KRAS mCRC patients had mutations within codons 12 and 13, respectively. To our knowledge, this is the first study in Brunei Darussalam to analyse both the survival outcomes of metastatic CRC patients and those of mutant KRAS mCRC patients. Chi-squared analysis showed a significant difference between the survival outcomes of wild-type KRAS and mutant KRAS mCRC patients (p-value = 0.024). There was a significant difference in the survival outcome between the mutant KRAS mCRC patients with RCC and mutant KRAS mCRC with LCC patients. There was no significant difference between the survival outcomes of mutant KRAS patients with mutations in either codon 12 or 13 of the KRAS gene (Table 3). However, there is a significant difference in the median survival periods between the mutant KRAS mCRC patients with mutations in codon 12 and those with mutation in codon 13 of the KRAS gene (p-value = 0.003). In conclusion, we found that mutant KRAS mCRC patients had a significantly poorer OS, which was shown to be worse when the primary tumours were found at the left side of the colon. Mutant KRAS mCRC patients with mutations in codon 12 were found to have shorter survival median periods than those with mutations within codon 13.

The high mutation rate of human immunodeficiency virus type 1 (HIV-1) plays a major role in treatment resistance from the development of vaccines to long-lasting drugs. In addressing the crux of the issue, various attempts to estimate the mutation rate of HIV-1 resulted in a large range of 10-5 - 10-3 errors/bp/cycle due to the use of different types of investigation methods. In this review, we discuss the different assay methods, their findings on the mutation rates of HIV-1 and how the location of these mutations can be further analyzed for their potential allosteric effects to reveal potentially new inhibitors with different pharmacodynamics that can be used to circumvent fast occurring HIV drug resistance. Given that HIV is one of the fastest mutating viruses, it is a good model for comprehensive study of its mutations that can give rise to much horizontal understanding towards overall viral drug resistance as well as emerging viral diseases.

Therapeutics antibodies have increasingly shifted the paradigm of disease treatments, from small molecules to biologics, especially in cancer therapy. Despite the increasing number of antibody candidates, much remains unknown about the antibody and how its various regions interact. In fact, the constant region can govern effects that might be useful in reducing the unwanted consequences resulted from systemic circulation. For this reason, apart from the commonly used IgG isotypes, IgA antibodies are promising therapeutics drugs, given its localized mucosal effects. While the antibody Fc effector cell activity has been well explored, recent research has shown evidences that the constant region of the antibody can also influence antigen binding, challenging the conventional idea of region-specific antibody functions. To further investigate this, we analyzed the IgA antibody constant and its allosteric effects onto the antigen binding regions, using recombinant Pertuzumab IgA1 and IgA2 variants. We found mutations in the C-region to reduce Her2 binding, and our computational structural analysis showed that such allosteric communications were highly dependent on the antibody hinge, providing the evidence to consider antibodies as a whole protein rather than a sum of functional regions.

This paper presents a 32 GHz high power amplifier (HPA) with a design strategy to achieve a high-power output with reliable operation for the Ka-band deep space satellite communication in 150 nm GaN HEMT technology. The presented Ka-band HPA employs a cascaded two-stage common source amplifier topology, and the output stage is comprised of an 8-way power combining network in current mode. The interstage matching network is designed with the bandpass configuration utilizing capacitors and transmission lines to provide better stability at the low-frequency regime. The implemented Ka-band HPA achieved a peak power gain of 7.3 dB at 32 GHz and a 3 dB bandwidth was 3.5 GHz between 31.3 and 34.8 GHz. The saturated output power at the peak power added efficiency (PAE) of 19.3% was 38.2 dBm, and the output 1 dB gain compression point (OP1dB) was 27.4 dBm in the measurement. The designed HPA consumes an area of 19.35 mm^2 including RF signal, and DC pads

We have investigated the interfacial dislocations in InxGa1–xN/GaN (0 ≤ x ≤ 0.20) heterostructures using diffraction contrast analysis in a transmission electron microscopy. The analysis indicate that the structural properties of the interface dislocations depend on the indium composition. For lower indium composition up to x = 0.09, we observed that the screw-type dislocations and dislocation half loops occurred at the interface even though the former do not contributes toward elastic relaxation of the misfit strain in the InGaN layer. With the increase of indium composition (0.13 ≤ x ≤ 0.17), in addition to the network of screw-type dislocations, edge-type misfit dislocations were found generated with their density gradually increasing. For higher indium composition (0.18 ≤ x ≤ 0.20), all the interfacial dislocations are transformed into a network of straight misfit dislocations along the <10-10> directions leading to partially relaxation of the InGaN epilayer. The presence of dislocation half loops may be explained by slip on the basal plane, the formation of misfit dislocations are attributed to punch-out mechanism.

In recent years, neural networks based on attention mechanisms have been increasingly widely used in speech recognition, separation, enhancement, and other fields. In particular, the convolution-augmented transformer has achieved good performance as it can combine the advantages of convolution and self-attention. Recently, the gated attention unit (GAU) has been proposed. Compared with the traditional multi-head self-attention, approaches with GAU are effective and computationally efficient. In this article, we propose a network for speech enhancement called CGA-MGAN, a kind of Metric GAN based on convolution-augmented gated attention. CGA-MGAN captures local and global correlations in speech signals at the same time through the fusion of convolution and gated attention units. Experiments on Voice Bank + DEMAND show that the CGA-MGAN we propose achieves an excellent performance (3.47 PESQ, 0.96 STOI, and 11.09dB SSNR) at a relatively small model size (1.14M).

One of the industries with the fastest rate of growth is healthcare, and this industry's enormous data requires extensive cloud storage. The cloud may offer some protection, but there is no assurance that data owners can rely on it for refuge and privacy amenities. Therefore, it is essential to offer security and privacy protection. Increased customer satisfaction with security and privacy preservation is crucial since healthcare big data and its sources are stored in the cloud and contain increasingly private and sensitive information. However, maintaining privacy and security in an untrusted green cloud environment is difficult, thus the data owner should have complete data control. A new work SecPri-BGMPOP(security and privacy of Boost graph Convolutional Network -Pinpointing-Optimization Performance) is suggested that can offer a solution that involves several different steps in order to handle the numerous problems relating to security and protecting privacy. Initially Boost Graph Convolutional Network Clustering (BGCNC) algorithm, which reduces computational complexity in terms of time and memory measurements, is first applied to the input dataset to begin the clustering process. Second, enlarge by employing a piece of the magnifying bit string to generate a safe key, pinpointing based encryption avoids amplify leakage even if a rival or attacker decrypts the key or asymmetric encryption. Finally, to determine the accuracy of the method, an optimal key was created using a meta-heuristic algorithmic framework called Hybrid fragment horde bland lobo Optimization (HFHBLO). Our proposed method currently kept in a cloud environment, allowing analytics users to utilize it without risking their privacy or security.

HIV treatment strategies against viral enzymes are continuously hampered by viral drug resistance. Recent findings show that viral substrate Gag contributes to HIV-1 Protease Inhibitor (PI) resistance, leading to demands for new strategies in HIV treatment where Gag is recognized as a drug target. To successfully target Gag, there is a need of in-depth understanding of the Gag polyprotein and the effects of Gag mutations. Here, we propose new strategies in designing novel Gag inhibitors against existing and novel emerging Gag mutations via a structural understanding of the Gag-Protease relationship in PI resistance. In this review, we discuss the role of both novel and previously reported mutations, revealing insights to how they aid in PI resistance, and how new Gag inhibitors can be designed.

This paper shares our work in developing and implementing an immersive gamification training platform for students who undergo manufacturing shopfloor training at the School of Engineering, Nanyang Polytechnic, Singapore. In this gamification training platform, we developed a virtual manufacturing shopfloor that is identical to the actual shopfloor located in the school. Students have the freedom to learn the manufacturing shopfloor operations and safety acts through the various game scenarios and training tasks which include workshop safety, CNC machine introduction, CNC machining dynamics, MES, etc. In addition, the assessment feature with immediate feedback were embedded within the gamification platform, which aim to help students to assess their level of understanding and help teachers to monitor the learning progress of their students. To investigate the impact of this gamification training platform on students’ learning outcome and motivation in manufacturing shopfloor technologies and safety acts, a pilot study was conducted in AY2018 semester 2 for a total 134 students from 4 classes of digital & precision engineering diploma. It is found that gamification can be integrated effectively into manufacturing education to motivate students and enhance their learning effectiveness. Based on the collected data from the technical quizzes and satisfactory survey, the results showed that the integration of gamification into the classroom learning not only added a stimulating and captivating game-like layer to the learning experience of the students, but also provided a safe environment for students to learn without fear of making errors. Challenges faced in implementing this gamification training platform will also be discussed in this paper.

Mobility is a vital welfare indicator which may influence broilers’ daily activities. Classical broiler mobility assessment methods are laborious and cannot provide timely insights into their conditions. Here, we proposed a semi-supervised Deep Learning (DL) model, YOLOv5, combined with Deep Sort algorithm conjoined with our newly proposed algorithm, Neo-Deep Sort, for individual broiler mobility tracking. Initially, 1,650 labeled images from five days were employed to train the YOLOv5 model. Through semi-supervised learning (SSL), this narrowly trained model was then used for pseudo-labeling 2,160 images, of which 2,153 were successfully labeled. Thereafter, the YOLOv5 model was fine-tuned on the newly labeled images. Lastly, the trained YOLOv5 and the Neo-Deep Sort algorithm were applied to detect and track 28 broilers in two pens and categorized them in terms of hourly and daily traveled distances and speeds. SSL helped in increasing the YOLOv5 model’s mean Average Precision (mAP), in detecting birds, from 81% to 98%. As compared with the manually measured covered distances of broilers, the combined model provided individual broiler's hourly moved distances with a validation accuracy of about 80%. Eventually, individual and flock level mobilities were quantified while overcoming the occlusion, false and miss detection issues.

Proposed as a response to the increasing global need for environmental protection, a green port balances economic vibrancy and environmental protection. However, because exhaust emissions (e.g., CO2 or sulfide) are difficult to monitor in and around ports, data on such emissions are often incomplete, which hinders research on this topic. To remedy this problem, this study aimed to formulate a method for collecting CO2 emissions data at their source; this method was applied to collect real-world operating data from a large container-handling company in Taiwan. Specifically, to account for undesirable outputs, we formulated a method that combines (1) data envelopment analysis based on a modified slack-based measure and (2) a multichoice goal programming approach. We found that rubber-tired gantry cranes are the greenest and should be used. Our findings aid port managers in selecting port equipment that best balances between environmental protection and profitability.

Despite widespread industrial use, the environmental safety of Hydroquinone (HQ), a benzene compound from plants used in processes like cosmetics, remains uncertain. This study evaluated the ecotoxicological impact of HQ on soil and river environments, utilizing non-target indicator organisms from diverse trophic levels: Daphnia magna, Vibrio fischeri, Allium cepa, and Eisenia fetida. For a more environmentally realistic assessment, microbial communities from a river and un-treated soil underwent 16S rRNA gene sequencing, with growth and changes in community-level physiological profiling assessed using Biolog EcoPlate™ assays. The water indicator D. magna exhibited the highest sensitivity to HQ (EC50 = 0.142 µg/mL), followed by V. fischeri (EC50 = 1.446 µg/mL), and A. cepa (LC50 = 7.631 µg/mL), while E. fetida showed the highest resistance (EC50 = 234 mg/Kg). Remarkably, microbial communities mitigated HQ impact in both aquatic and terrestrial environments. River microorganisms displayed minimal inhibition, except for a significant re-duction in polymer metabolism at the highest concentration (100 µg/mL). Soil communities demonstrated resilience up to 100 µg/mL, beyond which there was a significant decrease in population growth and the capacity to metabolize carbohydrates and polymers. Despite microbial mitigation, HQ remains highly toxic to various trophic levels, emphasizing the necessity for en-vironmental regulations.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

Fluorescence microscopic images of cells contain a large number of morphological features that are used as an unbiased source of quantitative information about cell status, through which researchers can extract quantitative information about cells and study the biological phenomena of cells through statistical and analytical analysis. As an important research object of phenotypic analysis, images have a great influence on the research results. Saturation artifacts present in the image result in a loss of grayscale information that does not reveal the true value of fluorescence intensity. From the perspective of data post-processing, we propose a two-stage cell image recovery model based on generative adversarial network to solve the problem of phenotypic feature loss caused by saturation artifacts. The model is capable of restoring large areas of missing phenotypic features. In the experiment, we adopt the strategy of progressive restore to improve the robustness of the training effect, and add the contextual attention structure to enhance the stability of the restore effect. We hope to use deep learning methods to mitigate the effects of saturation artifacts to reveal how chemical, genetic, and environmental factors affect cell state, providing an effective tool for studying the field of biological variability and improving image quality in analysis.

A millimeter-wave (mmWave) gallium nitride (GaN) high-power amplifier (PA) monolithic microwave-integrated circuit (MMIC) was implemented, considering a source via effect. In this paper, we introduce guidelines for designing GaN high PA MMICs, from device sizing to meeting high-power specifications, power matching considering source via effects, schematic design of three-stage amplifier structures, and electromagnetic (EM) simulation. Based on the results of load pull simulation and small-signal maximum stable gain (MSG) simulation, the GaN high electron-mobility transistor (HEMT) size was selected to be 8×70 μm. However, since the source via model provided by the foundry was significantly different from the EM results, it was necessary to readjust the power matching considering this. Additionally, when selecting the source via size, the larger the size, the easier the matching, but since the layout of the peripheral bias circuit is not possible, a compromise was required considering the actual layout. To prevent in-band oscillation, an RC parallel circuit was added to the input matching circuit, and low-frequency oscillation was solved by adding a gate resistor on the PCB module. The proposed PA was fabricated with a commercial 0.1 μm GaN HEMT MMIC process. It exhibited 38.56 to 39.71 dBm output power (Pout), 14.2 to 16.7 dB linear gain, and 14.1% to 18.2% power-added efficiency (PAE) between 34 and 36 GHz. The fabricated GaN power amplifier MMIC shows competitive Pout in the Ka upper band above 33 GHz

Micro-Raman spectroscopy was carried out to evaluate the localized residual stresses in commercial Gallium Nitride-based devices, specifically AlGaN/GaN High Electron Mobility Transistors (HEMTs) in a novel packaging design provided by STMicroelectronics S.r.l. The packaging plays a key role in protecting the device core against the external environment, thus minimizing damages caused by mechanical shocks, exposure to light, and contact with chemicals, conjointly achieving an efficient heat dissipation rate. Even though the packaging is a required step for the proper functioning of ready-to-use electronic devices, its application typically may introduce mechanical stress to AlGaN/GaN HEMTs, which can result in various reliability issues. In this paper, we investigate the impact of packaging on residual stress by analyzing the frequency shift of the E2 Raman peak along GaN layers and at the GaN/Si interface. An extensive evaluation was conducted using both a packaged device and a wafer-level device. The correlation between Raman frequency shifts of the E2 mode was accurately quantified, revealing a stress mitigation of approximately 0.1 GPa. This reduction is ascribed to the compressive stress introduced by the packaging, which partially offsets the intrinsic tensile stress of the wafer-level device. The proposed methodology could, in principle, be implemented to improve the development of a packaging.

GaN nanowires grown on metal substrates attract an increasing interest for a wide range of applications. Herein, we report GaN nanowires grown by plasma-assisted molecular beam epitaxy on thin polycrystalline ZrN buffer layers, sputtered onto Si(111) substrates. The nanowire orientation is studied experimentally and described within a model as a function of the Ga beam angle, nanowire tilt angle and substrate rotation. We show that vertically aligned nanowires grow faster than inclined nanowires, which leads to an interesting effect of geometrical selection of the nanowire orientation in the directional molecular beam epitaxy technique. After a given growth time, this effect depends on the nanowire surface density. At low density, the nanowires continue to grow with random orientations as nucleated. At high density, the effect of preferential growth induced by unidirectional supply of material in MBE starts to dominate. Faster growing nanowires with smaller tilt angles shadow more inclined nanowires that grow slower. This helps to obtain more regular ensembles of vertically oriented GaN nanowires despite their random position induced by the metallic grains at nucleation. The obtained dense ensembles of vertically aligned GaN nanowires on ZrN/Si(111) surfaces are highly relevant for device applications. These results are not specific for GaN nanowires and should be relevant for any nanowires which are epitaxially linked to the randomly oriented surface grains in the directional molecular beam epitaxy.

Kawasaki disease is a febrile illness characterised by systemic inflammation of small- and medium-sized blood vessels which commonly occurs in young children. Although self-limiting, there is a risk of developing coronary artery lesions as disease progresses with delay in diagnosis and treatment. Unfortunately, the diagnosis of KD continues to remain a clinical dilemma. Thus, this article not only summarises the key research gaps associated to KD, but also evaluates the possibility of using circulating endothelial injury biomarkers such as, circulating endothelial cells, endothelial microparticles and vascular endothelial cell-free DNA, as diagnostic and prognostic tool of KD: a “liquid biopsy” approach. The challenges of translating liquid biopsies to use in KD, and the opportunities for improvement in its diagnosis and management that such translation may provide are discussed. The use of endothelial damage markers, which are easily obtained via blood collection, as diagnostics is promising and we hope this will be translated to clinical applications in the near future.

Study Region -This study is conducted for a cluster of watersheds within the Matagorda Basin along the south Texas coast in the United States. Study Focus - Retrospective streamflow simulations of two hydrologic models of contrasting formulations and complexity, namely the TxRR, a simple analog model, and the National Water Model (NWM), a land surface-hydrologic model that explicitly accounts for surface energy balance in calculating water budget, and whose output. The comparison was motivated by a) the need for improving the modeling of runoff dynamics for watersheds along central Texas coast through the introduction of NWM to inform freshwater inflow monitoring and flood planning, and b) the need to better understand the potential ability of the NWM to address shortcomings of TxRR related to the latter’s mechanistic deficiencies in a region known for hydroclimatic extremes. The study focuses on the temporal scale and climate dependence in the relative performance of the two models, the behaviors of models during extreme floods and droughts, and the relative efficacy of parameter transfer schemes. It further seeks to relate the performance differentials to model physics and calibration approaches. New Hydrologic Insights – NWM, with sophisticated representations of energe closure, is advantageous to TxRR in capturing low-frequency (interannual) variations in streamflow modulated by the surface energy balance, as evidenced by the superior correlation of its streamflow simulations at the interannual range. Yet, its overall performance trails behind TxRR at daily scale, and it tends to underpredict runoff volumes during two major floods. These features underscore the tendency of the model to suppress soil moisture at the onset of these events. On the other hand, TxRR outperforms in reproducing the volumes for the flooding events, but it overpredicts runoff during the extreme drought episode of 2011, likely an outcome of inadequate representation of the impacts of root zone soil moisture in regulating runoff. TxRR’s parameteralization scheme proves more effective for adaptation across watersheds due to the presence of steep gradation in soil properties .

The once-held wisdom of the supreme efficiency of one-way streets has been gradually sup-planted by the perceived sustainability of two-way streets in the design of livable cities that prioritizes the safety of pedestrians and thriving of local businesses. However, it is rarely dis-cussed on whether one-way street conversions have truly improved the long-term traffic effi-ciencies on urban street networks, as conflating socioeconomic factors such as vehicular popula-tion growth and induced travel demand may render empirical analysis inconclusive. In this study, microscopic traffic simulations implemented on SUMO platform was performed to ana-lyze the effect of street conversion in Downtown Brickfields, Kuala Lumpur. This approach can control and standardize travel demand in both one-way and two-way street networks, and would therefore give a fairer evaluation by precluding all socioeconomic factors. It was found that one-way streets do not necessarily improve the traffic efficiency of the network, as it is very dependent on the traffic scenario evolution over time. One-way streets perform better at the on-set of traffic congestion due to its higher capacity, but on average, the 4-fold longer travel times that made it harder to clear traffic by getting vehicles to their destinations compared to two-way streets. As time progresses, congestion in one-way streets may become twice as worse compared to two-way streets. This study may contribute to a more holistic assessment of traffic circulation plan designed for smart and livable cities

The prevalence and factors associated with metabolic syndrome (MetS) remain unknown in Malaysian vegetarians. This cross-sectional study aimed to determine the prevalence of MetS among vegetarians in Kuala Lumpur and Selangor and its associated factors. The data on socio-demographic characteristics, vegetarianism practices, lifestyle behaviours, body weight, height, waist circumference (WC), systolic blood pressure (SBP), diastolic blood pressure (DBP), fasting blood glucose (FBG), and blood lipid profiles were collected from 273 vegetarians. A majority of the respondents were lacto-ovo vegetarians (44.0%), females (64.8%) and Chinese (54.9%). The prevalence of MetS was 24.2%. High BP (48.7%) and high WC (43.6%) were the most common MetS components. Females had lower WC, SBP, DBP, FBG, TG and higher HDL-c (p < 0.05) as compared to males. Multiple logistic regression analysis showed that advancing in age (OR = 1.03, 95% CI: 1.00-1.06), and overweight and obesity (OR = 7.90, 95% CI: 4.13-15.11) were the risk factors of MetS after adjusted for sex. This study found that one in four vegetarians had MetS. The present findings emphasize the need to focus among vegetarians with older age. An intervention program to reduce BMI should be established among vegetarians, especially among those vegetarians who were overweight and obese.

The detection performance of small objects in remote sensing images has not been satisfactory compared to large objects, especially in low-resolution and noisy images. A generative adversarial network (GAN)-based model called enhanced super-resolution GAN (ESRGAN) showed remarkable image enhancement performance, but reconstructed images usually miss high-frequency edge information. Therefore, object detection performance showed degradation for small objects on recovered noisy and low-resolution remote sensing images. Inspired by the success of edge enhanced GAN (EEGAN) and ESRGAN, we applied a new edge-enhanced super-resolution GAN (EESRGAN) to improve the quality of remote sensing images and used different detector networks in an end-to-end manner where detector loss was backpropagated into the EESRGAN to improve the detection performance. We proposed an architecture with three components: ESRGAN, EEN, and Detection network. We used residual-in-residual dense blocks (RRDB) for both the ESRGAN and EEN, and for the detector network, we used a faster region-based convolutional network (FRCNN) (two-stage detector) and a single-shot multibox detector (SSD) (one stage detector). Extensive experiments on a public (car overhead with context) dataset and another self-assembled (oil and gas storage tank) satellite dataset showed superior performance of our method compared to the standalone state-of-the-art object detectors.

The global demands for various grains including durum wheat (Triticum durum Desf.) are expected to increase substantially in the coming years due to ever-growing human population’s needs for food, feed and fuel. Thus, providing consistent or increased durum grain to the world market is one of the priorities for policy-makers, researchers, and farmers. What are the major achievements in agronomic advancement for durum wheat cultivation in recent decades? How might the current cropping systems be improved to increase crop yield and quality and improve resource use efficiencies while minimizing input costs and decreasing negative impact on the environment? Canada is one of the major durum wheat producers in the world, as Canada contributes about 50% to global trade of durum grain. Canada’s research achievements in durum wheat might serve as a guide for advancing the cultivation of the crop in other regions/countries on the planet. This review summarizes the major Canadian research findings in the aspects of durum wheat agronomics during the period 2001 to 2017 years. It highlights the main advancements in seeding and tillage, crop rotation and diversification, and use of pulse-induced microbiomes to improve soil health and feedback mechanism. The genetic gain and breeding for resistance against abiotic and biotic stresses are discussed. Finally, we identified main constraints and suggested some near-term research priorities. The research findings highlighted in this review will be of use for other areas on the planet to increase durum wheat productivity, improve soil fertility and health, and enhance long-term sustainability.

We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal-organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (¯201) orientation peaks of -Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 x1018 cm-3 and mobility of ~770 cm2V-1s-1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance-voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 x1013 cm-2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV-1. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.

Generative models for images, audio, text and other low-dimension data have achieved great success in recent years. Generating artificial human movements can also be useful for many applications, including improvement of data augmentation methods for human gesture recognition. The object of this research is to develop a generative model for skeletal human movement, allowing to control the action type of generated motion while keeping the authenticity of the result and the natural style variability of gesture execution. We propose to use a conditional Deep Convolutional Generative Adversarial Network (DC-GAN) applied to pseudo-images representing skeletal pose sequences using Tree Structure Skeleton Image format. We evaluate our approach on the 3D-skeleton data provided in the large NTU RGB+D public dataset. Our generative model can output qualitatively correct skeletal human movements for any of its 60 action classes. We also quantitatively evaluate the performance of our model by computing Frechet Inception Distances, which shows strong correlation to human judgement. Up to our knowledge, our work is the first successful class-conditioned generative model for human skeletal motions based on pseudo-image representation of skeletal pose sequences.

Europium is the most-studied and least-well-understood rare earth ion (REI) dopant in GaN. While attempting to increase the efficiency of red GaN light-emitting diodes (LEDs) by implanting Eu⁺ into p-type GaN templates, the Strathclyde University group, in collaboration with IST Lisbon and Unipress Warsaw, discovered hysteretic photochromic switching (HPS) in the photoluminescence spectrum of doubly doped GaN(Mg):Eu. Our recent work, summarised in this contribution, has used time-, temperature- and light-induced changes in the Eu intra-4f shell emission spectrum to deduce the microscopic nature of the Mg-Eu defects that form in this material. As well as shedding light on the Mg acceptor in GaN, we propose a possible role for these emission centres in quantum information and computing.

Digital healthcare systems play a pivotal role in providing efficient and accessible healthcare services. However, ensuring secure authentication and key agreement mechanisms is essential to protect sensitive patient data and maintain the integrity of the system. The existing methods face limitations in terms of vulnerability to cyber attacks, scalability, and resource utilization. Furthermore, the integration of blockchain technology introduces new complexities that need to be addressed. This research proposes an optimized fuzzy logic approach combined with blockchain technology to address the authentication and key agreement challenges in digital healthcare systems. The proposed solution leverages the flexibility and adaptability of fuzzy logic algorithms to handle uncertainty and imprecision in authentication decisions. By employing fuzzy logic, the system can effectively minimize false positives and false negatives, enhancing the robustness against adversarial attacks. Moreover, the integration of blockchain technology provides a decentralized and tamper-proof infrastructure for securely storing and managing authentication and key agreement data. This ensures transparency and trust in the system, mitigating the risks of unauthorized access and data manipulation. The blockchain-based architecture also enables efficient resource utilization and scalability, allowing the system to handle authentication requests in a timely manner, even in large-scale digital healthcare environments.The proposed method is evaluated by using the NIST Special Database 302 and it shows superior performance compared to existing methods, with minimum False Rejection Rate (FRR), False Acceptance Rate (FAR), and response time. Moreover, the proposed method minimizes communication overhead during the authentication process and resists different cyber attacks including a Replay attack, Man-in-the-middle attack, Denial of Service (DoS) attack, and Impersonation attack. The proposed method achieves excellent performance in terms of security, efficiency, and resistance to various cyber-attacks, making it a promising approach for secure data sharing in P2P cloud environments.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

To understand the health impacts of “hikikomori” lifestyle and to establish its first comprehensive health profile, a cross-sectional study was designed to measure how well the cases of hikikomori youths of Hong Kong were living, in terms of social, mental and physical aspects. This study involved 104 eligible participants at age 19.02 year-old who had completed the set of questionnaires and a series of anthropometric and physical health measurements. Despite SF36 score of 84.0 indicated good physical functioning in general, participants were lived sedentarily with high incidence of hypertension at 15.4% and prehypertension at 31.7%. Occurrence of hypertension in cases living as hikikomori >6 months was 3-times higher than those newly onset cases. The blood pressure levels were correlated with age and all obesity index parameters measured including waist circumference and body mass index. Half of the hypertensive cases involved the elevation of systolic blood pressure, which suggested higher odds of cardiovascular complications. Participants were mentally stable living with moderate levels of perceived stress and state anxiety, but borderline clinical depression. In conclusion, the hikikomori lifestyle could be a risk behavior that may harm the younger generation physically by promoting obesity and hypertension and probably other chronic illnesses.

Background Globally the average age of the worlds’ population of older persons continues to upsurge and social support becomes increasingly relevant. Overall, in Malaysia, social support and networking prevalence was found to be lower among older persons at 30.76%. In view of the scarce data on social support and its association with smoking status and its associated factors among the older Malaysian population this study was conducted. Methods Data from the National Health and Morbidity (NHMS) 2018 survey on health of older Malaysian adults was analyzed. This was a cross sectional population-based study using a two-stage stratified random sampling design. Elderly population aged 60 years and above was selected. Data were collected were sociodemographic characteristics, smoking status, and social support. A validated Malay language, interviewer-administered questionnaire of 11-item Duke Social Support Index was applied for assessing social support among the elderly. A complex sampling design analysis was used for the descriptive statistics. The associated risk factors for social support were identified using Multiple Logistic Regression analysis. Results A total of 3923 elderly respondents participated in the study. The prevalence of good social support was significantly higher among the 60-69 years old respondents compared to the > 80 years old (73.1%, 95% CI :69.3% -76.5% vs 50.1 %, 95% CI:41.7 %- 58.6%).Multivariate logistic regression analysis showed that the odds of poor social support were 1.7 times (aOR: 1.72 % ,95%CI: 1.19 -2.48) higher for the respondents aged > 80 years old, than those aged 60-69 years. Respondents with no formal education were 1.93 higher odds of poor social support than the respondents with tertiary education (aOR: 1.93%, 95%CI: 1.13,3.30). Respondents with income < RM 1000 were 1.94 times more likely to have poor social support compared to respondents with income > RM 3000 (aOR: 1.94, 95% CI : 1.21 -3.13). Former smokers have good social support compared to current smokers (73.6% ,95% CI: 67.7-78.7 vs 65.1 %, 95%CI:58.4 -71.2). For current smokers, the odds of poor social support were 42.0% higher than for non-smokers (aOR: 1.42, 95% CI: 1.05 -1.91. Conclusion There is poor social support among the older persons who are current smokers, advancing age, no formal education and low income However, further longitudinal studies are needed to determine the exact effects of the studied variables. These findings could assist the policymakers to develop strategies at the national level to enhance social support among the older smokers to ensure cessation of smoking.

Objective: We tested a model of individual health literacy information sharing with family members, personal preventive behaviours and family well-being during the Coronavirus Disease 2019 (COVID-19) pandemic in Hong Kong. Methods: We analysed data of 1501 randomly selected Chinese adults from a cross-sectional survey in Hong Kong from 9 to 23 April, 2020. Individual health literacy about COVID-19 with the items extracted from the questionnaire in World Health Organization Risk Communication and Community Engagement (RCCE) Action Plan Guidance for COVID-19 preparedness and response, COVID-19 information sharing with family members, preventive behaviours against COVID-19 and family well-being were measured. Structural equation modelling analysis tested the proposed model. Findings: COVID-19 information sharing with family members partially mediated the association between individual health literacy and personal preventive behaviours. The direct effect of 0.24 was shown, and the indirect effect through COVID-19 information sharing with family members was small at 0.03 (Z = 3.66, p < 0.001). Family well-being was associated with personal preventive behaviours against COVID-19. The model was adjusted for sex, age, and socioeconomic status factors and had good fit with RMSEA = 0.04, CFI = 0.98, TLI = 0.96, and SRMR = 0.02. Conclusion: COVID-19 information sharing with family members was a partial mediator between individual health literacy and personal preventive behaviours against COVID-19. Strategies for enhancing health literacy and preventive measures against COVID-19 are needed to promote family well-being in the pandemic.

Purposes: To provide abdominal contrast-enhanced MR image synthesis, we developed an image gradient regularized multi-modal multi-discrimination sparse-attention fusion generative adversarial network (GRMM-GAN) to avoid repeated contrast injections to patients and facilitate adaptive monitoring. Methods: With IRB approval, 165 abdominal MR studies from 61 liver cancer patients were retrospectively solicited from our institutional database. Each study included T2, T1 pre-contrast (T1pre), and T1 contrast-enhanced (T1ce) images. The GRMM-GAN synthesis pipeline consists of a sparse attention fusion network, an image gradient regularizer (GR), and a generative adversarial network with multi-discrimination. The studies were randomly divided into 115 for training, 20 for validation, and 30 for testing. The two pre-contrast MR modalities, T2 and T1pre images, were adopted as inputs in the training phase. The T1ce image at the portal venous phase was used as an output. The synthesized T1ce images were compared with the ground truth T1ce images. The evaluation metrics include peak signal-to-noise ratio (PSNR), structural-similarity-index (SSIM), and mean-squared-error (MSE). A Turing test and experts’ contours evaluated the image synthesis quality. Results: The proposed GRMM-GAN model achieved a PSNR of 28.56, an SSIM of 0.869, and an MSE of 83.27. The proposed model showed statistically significant improvements in all metrics tested with p-values <0.05 over the state-of-the-art model comparisons. The average Turing test score was 52.33%, close to random guessing, supporting the model's effectiveness for clinical application. In the tumor-specific region analysis, the average tumor contrast-to-noise ratio (CNR) of the synthesized MR images was not statistically significant from the real MR images. The average DICE from real vs. synthetic images was 0.90, compared to the inter-operator DICE of 0.91. Conclusion: We demonstrated the function of a novel multi-modal MR image synthesis neural network, GRMM-GAN, for T1ce MR synthesis based on pre-contrast T1 and T2 MR images. GRMM-GAN shows promise for avoiding repeated contrast injections during radiation therapy treatment.

This study explores the use of remote ultrasound vibration to enhance welding strength. It examines the effects of 20 kHz, and 40 kHz High Power Ultrasound Transducers (HPUT) in contact and contactless modes during ultrasonic assistance laser welding. Employing shear tests and microscopy for assessment, the research evaluates ultrasound's impact on welding strength and identifies the optimal transducer. Theoretical and numerical analyses investigate vibration transmission into the welding area, particularly examining the vibration distribution and cavitation initiation within the molten pool area. Results indicate that ultrasound-assisted welding increases pull test performance, including the resistance force and strain, and improves microscopic structural integrity. Numerical simulations suggest that narrow-band vibration intensifies pressure in specific welding zones. Contactless ultrasound application also shows enhanced welding quality, offering a promising alternative to current methods. This work contributes to electric car technology by suggesting improvements in welding techniques for power battery systems.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

Gestational Diabetes Mellitus (GDM) is related with adverse outcomes for both the mother and the offspring. Immune and senescence play a crucial role in GDM progression. This study aims to explore the diagnostic significance of immune-related senescence (IRS) genes in GDM. We used weighted gene co-expression network analysis (WGCNA) and single sample gene set enrichment analysis (ssGSEA) to compute the immune score and aging score in control and GDM samples. Machine learning identified core IRS genes. Then we performed unsupervised cluster analysis in GDM patients to explore immune infiltration. Finally, we validated the core genes in clinical samples. We used the intersection of MEblack module from WGCNA and differentially expressed genes (DEGs) to obtain the potential genes. Next, a univariate logistic regression model including 23 potential genes were constructed, and these genes were filtered by least absolute shrinkage and selection operator (LASSO) algorithm. There were 5 potential genes (COX17, RRAS2, RRAGC, CECR1, and TACC2), which defined as biomarkers, remained eventually, and the efficacy of these biomarkers was evaluated by nomogram. Finally, the results from both qRT-PCR and western blot analyses demonstrated CECR1 was down-regulated, while TACC2 was up-regulated in GDM placental tissue. Our study identified CECR1 and TACC2 as diagnostic biomarkers for GDM associating with immune and senescence, providing a new perspective on GDM progression.

Phage, which is often used therapeutically, has begun to receive interest as an alternative to antibiotic growth promoters (AGPs) to enhance chicken growth. Another option that has been extensively studied as a growth promoter in chicken is probiotics. However, there are no studies using phages and probiotics as prospective feed additives for broiler chickens. Therefore, this study demonstrated the effects of phage cocktail, probiotics and their combinations on growth performance and gut microbiota of broiler chickens. A total of 288 one-day-old male Cobb 500 broilers were randomly allotted to 1 of 6 treatments in a completely randomised design. The treatments were: (i) C (basal diet (BD) only), (ii) 1ɸ (BD + 0.1% phage cocktail), (iii) 2ɸ (BD + 0.2% phage cocktail), (iv) P (BD + 0.1% probiotic), (v) 1ɸP (BD + 0.1% phage cocktail + 0.1% probiotic), (vi) 2ɸP (BD + 0.2% phage cocktail + 0.1% probiotic). The 1ɸP treatment had significantly (P < 0.05) better BW (35 d), BWG (22 – 35 d, 1 – 35d), and FCR (1-21 d. 22-35 d, 1-35 d) compared to C. Unique gut microbiota diversity was also found between the ɸP (1ɸP and 2ɸP) and non-ɸP groups (C, 1ɸ, 2ɸ and P) in ilea, particularly in the 35 d chickens. Microorganisms associated with short-chain fatty acid (SCFA) producers were significantly (P <0.05) present in the ɸP group than in the non- ɸP group. The carbohydrate and amino acid metabolism predicted genes were significantly upregulated in ɸP groups compared to non- ɸP groups. These genes were involved in the digestion and absorption of nutrients as well as the production of energy. Our findings showed that 1ɸP treatment could be a potential alternative to AGPs for poultry where growth performance was enhanced, and gut microbiota was positively modulated.

In this paper, we present the investigation results of radiation-induced effects in metal-oxide-semiconductor (MOS) doped with moderate amounts of Zinc Oxide (ZnO) as a potential candidate for space-borne application. The samples were fabricated via the sputtering method at a working pressure of 3mTorr and a deposition temperature of 300oC. The ZnO samples were exposed to 1.25-MeV gamma-ray utilizing Co60 source, and their electronic response was measured at ionizing doses ranging from 10 kGy to 300 kGy. A comparative work was performed through finite element method to simulate the electronic response of the PN junction diode due to ionizing radiation. The results indicate that the ideality factor of the MOS diode increases as the ionizing dose increases, rendering it unsuitable for use as a diode. The degradation of the electrical parameters was also simulated, showing the increase in hole concentration. These findings suggest that the ejection of electrons occurred, which agrees with the gamma radiation effects trend. Furthermore, as the intensity of radiation increases, the spatial charge that arises from the separation of hole-electron pairs results in a substantial reduction of the electric field in the central portion of the n-type region. These findings provide insights into the degradation of electrical parameters in MOS devices under gamma radiation and have implications for their use in space-borne applications.

Point defect-based single-photon emitters (SPEs) in GaN have aroused a great deal of interest due to their room-temperature operation, narrow line width and high emission rate. The room-temperature SPEs at the telecommunication bands have also been realized recently by localized defects in GaN in experiments, which are highly desired for the practical applications of SPEs in quantum communication with fiber compatibility. However, the origin and underlying mechanism of the SPEs remain unclear to date. Herein, our first-principle calculations predict and identify an intrinsic point defect NGa in GaN that owns a zero-phonon line (ZPL) at telecommunication windows. By tuning the triaxial compressive strain of the crystal structure, the ZPL of NGa can be modulated from 0.849 eV to 0.984 eV, covering the fiber telecommunication windows from the O band to the E band. Besides the ZPL, the formation energy, band structure, transition process and lifetime of the SPEs under different strains are investigated systematically. Our work gives insight into the emission mechanism of the defect SPEs in GaN and also provides effective guidance for achieving wavelength-tunable SPEs working in fiber telecommunication windows.

The coronavirus (covid-19) pandemic is putting healthcare systems across the world under unprecedented and increasing pressure according to the World Health Organization (WHO). With the advances in computer algorithms and especially Artificial Intelligence, the detection of this type of virus in the early stages will help in fast recovery and help in releasing the pressure off healthcare systems. In this paper, a GAN with deep transfer learning for coronavirus detection in chest x-ray images is presented. The lack of benchmark datasets for covid-19 especially in chest x-rays images is the main motivation of this research. The main idea is to collect all the possible images for covid-19 that exists until the writing of this research and use the GAN network to generate more images to help in the detection of the virus from the available x-rays images with the highest accuracy possible. The dataset used in this research was collected from different sources and it is available for researchers to download and use it. The number of images in the collected dataset is 307 images for four different types of classes. The classes are the covid-19, normal, pneumonia bacterial, and pneumonia virus. The dataset is divided into 90% for the GAN and the training and the validation phase, while 10% used in the testing phase. The GAN helps in generating more images from the original dataset to be 30 times larger than the originally collected dataset. The GAN also help in overcoming the overfitting problem and made the proposed model more robust. Three deep transfer models are selected in this research for investigation. The models are the Alexnet, Googlenet, and Restnet18. Those models are selected based on their small number of layers on their architectures, which will reflect in reducing the complexity of the models and the consumed memory and time. Using a combination of GAN and deep transfer models prove it is efficiency according to validation, testing accuracy, and performance measurements such as precision, recall, and F1 score. Three case scenarios are tested through the paper, the first scenario which includes 4 classes from the dataset, while the second scenario includes 3 classes and the third scenario includes 2 classes. All the scenarios include the covid-19 class as it is the main target of this research to be detected. In the first scenario, the Googlenet is selected to be the main deep transfer model as it achieves 80.6% in testing accuracy. In the second scenario, the Alexnet is selected to be the main deep transfer model as it achieves 85.2% in testing accuracy, while in the third scenario which includes 2 classes(covid-19, and normal), Googlenet is selected to be the main deep transfer model as it achieves 100% in testing accuracy and 99.9% in the validation accuracy. All the performance measurement strengthen the obtained results through the research. Finally, this research may be considered one of the first trails to use GAN and deep transfer models together to help in detecting coronaviruses (covid-19) within the absence of a benchmark dataset around the world, especially in x-rays chest images.