On 17 October 1947, Niels Bohr was made a knight of the Order of the Elephant by the King of Denmark in view of his outstanding achievements and contributions to science. Bohr designed his own coat of arms that featured a pattern of Yin and Yang (Tai Chi symbol) to symbolize the wave-particle complementarity. However, Bohr’s Yin-Yang diagram (YYD) was neither drawn based on the principles of quantum mechanics, nor did it originate from the traditional Taoist YYD. Scientists still have doubts about the legitimacy of using YYD as the icon of the wave-particle complementarity, because the YYD belonging to quantum mechanics itself is unknown so far. This article reports the YYDs existing in quantum mechanics and justifies the role of YYD in the wave-particle duality by showing that any system, whether classical or quantum, has an ideal YYD as long as it satisfies Bohr’s principle of complementarity (BPC). The deviation of a deformed YYD from the ideal YYD indicates the extent to which a real system satisfies BPC. This article constructs the quantum YYD by the complex quantum trajectory of a particle tunneling via a step barrier, which displays the continuous transition between the wave behavior and the particle behavior. It appears that the YYD designed by Bohr in his coat of arms resembles the YYD generated by tunneling motion, not only in appearance but also in the governing equation.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

Physical inactivity is a well-known risk factor for various non-communicable diseases (NCDs). Sufficient physical activity (PA) is essential for the prevention of NCDs and thus it is imperative to study the current status of PA and its influencing factors among rural residents in China. A population-based survey was conducted in rural areas of Shandong, Shanxi and Yunnan Provinces using a stratified random sampling method. The International Physical Activity Questionnaire Short Form (IPAQ-S) was used to collect the data on PA. A total of 3780 rural residents participated in the survey. The result showed that 22.2% of rural residents were physical inactivity. The proportion of rural residents reporting practice of physical exercise was 54.4%. The most frequently performed physical exercise was walking/brisk walking(78.3%).Binary logistic regression analyses showed that being female, people at age between 15 to 34 years or 60 years old and above, employees of governmental departments/retirees, school students, the unemployed, people with NCDs were risk factors of PA and ethnic minority groups,smoking and alcohol consumption were risk factors of physical exercise. Health promotion programme aiming at increasing people’s PA in rural China is needed and it should focus on the populations groups of the female, people at age 60 years and above ,school students, the unemployed, and people with NCDs.

Background: The aim of this study was to investigate the risk of obstructive sleep apnea (OSA) among ankylosing spondylitis (AS) patients in a nationwide population. Methods: We conducted a nationwide cohort study between 2003 and 2013 using the Taiwan National Health Insurance Research Database. The AS cohort included 2210 patients who were newly diagnosed between 2003 and 2013. Randomly selected non-AS controls were matched at a 1:4 ratio based on age, sex and index date. The endpoint of OSA was occurrence or the end of 2013. Cumulative incidences, hazard ratios (HRs) and 95% confidence intervals (CIs) were calculated after adjusting for age, gender, comorbidities and co-medications. Multivariate analyses were performed using Cox proportional hazards model. Due to violation of the proportionality assumption, landmark analysis was conducted to explore the risk of OSA during specific follow-up periods. Results: The adjusted HR (aHR) of OSA for the AS group was 2.826 (95% C.I. = 1.727–4.625) compared to the control group. On landmark analysis, aHR was 7.919 (95% C.I. = 3.169–19.792) for AS group 0–24 months from index date, and decreased to 1.816 (95% C.I. = 0.944–3.494) at ≥ 24 months from index date. On subgroup analyses increased risks of OSA in AS group compared to the control group were found for both males and females (aHRs were 4.533 (95% C.I. = 1.441–14.262) and 2.672 (95% C.I. = 1.522–4.692) for females and males, respectively). On age stratified analysis, there was significant risk only for the 40–59 age group with aHR of 3.913 (95% C.I. = 1.890–8.102). Conclusions: A higher risk of developing OSA was found among newly diagnosed AS cohort during the 12-year follow-up period, especially within 2 years after AS index date and in the 40–59 age group.

The nonlinear dynamics exhibited by aircraft flying at high angle of attack (AOA) pose great challenges to the design of flight control. The control design based on nonlinear dynamic inversion (NDI) is to reversely find the required control input based on the current nonlinear dynamics of the aircraft and the control objectives to be achieved. Since it is derived from the nonlinear dynamics of the aircraft, a single NDI controller can cover the entire flight envelope without the need for controller switching or gain scheduling. This paper employs the layered structure of the flight control loop to implement the NDI controller through the combination of aerodynamic control and thrust vectoring control (TVC). The resulting NDI controller is applied to an experimental F-16 installed with TVC to verify its high AOA maneuverability in the post-stall region. The verification simulation shows that the experimental F-16 under the NDI control can effectively track the high AOA command and successfully demonstrate the Herbst maneuver by performing the heading reversal with 70° AOA.

With the realization of the Grand Canal's full water supply and the strong pursuit of green and low-carbon transportation in contemporary society, the value of the Grand Canal's water transport has been further affirmed, and its coordinated development with other transportation modes has become inevitable and important. This paper analyzes and combs through the characteristics, development status and existing problems of Grand Canal water transport and other transport modes in depth, and takes Jiangsu as an example. A collaboration model of Grand Canal water transport and other transport modes was built and their collaboration degree has been calculated. It is believed that the coordinated development of Grand Canal water transport and other transport modes can be greatly promoted via four aspects: optimizing the construction and governance of Grand Canal water transport, building an integrated management platform of transport modes, improving the integrated transport network structure, and promoting the deep integration of integrated shipping and tourism.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

Transition metal dichalcogenides (TMDs) monolayers exhibit unique valleytronics properties due to the dependency of the coupled valley and spin state at the hexagonal corner of the first Brillouin zone. Precisely controlling valley spin-polarization via manipulating the electron population enables its application in valley-based memory or quantum technologies. This study uncovered the uncompensated spins of the antiferromagnetic oxide (NiO) serving as the ferromagnetic (FM) order to induce valley spin-polarization in molybdenum disulfide (MoS₂) monolayers via the magnetic proximity effect (MPE). A spin-resolved photoluminescence spectroscopy (SR-PL) was employed to observe MoS₂, where the spin-polarized trions appear to be responsible for the MPE, leading to a valley magnetism. Results indicate that local FM order from the uncompensated surface of NiO could successfully induce significant valley spin-polarization in MoS₂ with the depolarization temperature approximately at 100 K, which is relatively high compared to related literature. This study reveals new perspectives and potential of AFM materials in the field of exchange-coupled van der Waals heterostructures.

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

Keywords: Porcine reproductive and respiratory syndrome virus, baculovirus surface display vectors, neutralizing antibody, IFN-γ, IL-4.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

In this paper, we present a novel Two-Echelon Ground Vehicle and Its Mounted Unmanned Aerial Vehicle Cooperated Routing Problem (2E-GUCRP). The 2E-GUCRP arises in the field of Unmanned Aerial Vehicle (UAV) Routing Problem such as those encountered in the context of city logistics. In a typical cooperated system, the UAV is launched from the Ground Vehicle (GV) and automatically flies to the designated target. Meanwhile, acting as a mobile base station, the GV can charge or change the UAV’s battery on the designated landing points to enable the UAV to continue its mission. The objective is to design efficient GV and UAV routes to minimize the total mission time while meeting the operational constraints. A Mixed Integer Programming (MIP) model, which could be solved by commercial software, is constructed to describe this problem. In order to quickly solve the medium-scale problems, two existing heuristics to solve 2E-VRP are improved. The computational experiments are set up to compare our model with the 2E-VRP. The results indicate that the 2E-GUCRP obtains a better efficiency. Further discussion of the practical instance points out that the increase in efficiency is related to the speed relationship between the GV and the UAV.

Like traditional single label learning, multi-label learning is also faced with the problem of dimensional disaster.Feature selection is an effective technique for dimensionality reduction and learning efficiency improvement of high-dimensional data. In this paper, Logistic regression, manifold learning and sparse regularization were combined to construct a joint framework for multi-label feature selection (LMFS). Firstly, the sparsity of the eigenweight matrix is constrained by the $L_{2,1}$-norm. Secondly, the feature manifold and label manifold can constrain the feature weight matrix to make it fit the data information and label information better. An iterative updating algorithm is designed and the convergence of the algorithm is proved.Finally, the LMFS algorithm is compared with DRMFS, SCLS and other algorithms on eight classical multi-label data sets. The experimental results show the effectiveness of LMFS algorithm.

Objective: Scaphoid fractures, particularly occult and non-displaced fractures, are difficult to detect using traditional X-ray methods due to their subtle appearance and variability in bone density. The study proposes a two-stage CNN approach to detect and classify scaphoid fractures using anterior-posterior (AP) and lateral (LA) X-ray views for more accurate diagnosis. Methods: The study emphasizes the use of multi-view X-ray images (AP and LA views) to improve fracture detection and classification. The multi-view fusion module helps integrate information from both views to enhance detection accuracy, particularly for occult fractures that may not be visible in a single view. The proposed method includes two stages that are stage 1: Detect the scaphoid bone using Faster R-CNN and Feature Pyramid Network (FPN) for region proposal and small object detection. The detection accuracy for scaphoid localization is 100% with Intersection over Union (IoU) scores of 0.8662 for AP views and 0.8478 for LA views. And stage 2: Perform fracture classification using a ResNet backbone and FPN combined with a multi-view fusion module to combine features from both AP and LA views. This stage achieves a classification accuracy of 89.94%, recall of 87.33%, and precision of 90.36%. Results: The proposed model performs well in both scaphoid bone detection and fracture classification. The multi-view fusion approach significantly improves recall and accuracy in detecting fractures compared to single-view approaches. In scaphoid detection, both AP and LA views achieved 100% detection accuracy. In fracture detection, using multi-view fusion, the accuracy for AP views reached 87.16%, and for LA views, it reached 83.83%. Conclusion: The multi-view fusion model effectively improves the detection of scaphoid fractures, particularly in cases of occult and non-displaced fractures. The model provides a reliable, automated approach to assist clinicians in detecting and diagnosing scaphoid fractures more efficiently.

Unmanned Aerial Vehicles (UAVs) severing as the relay is an effective technology method to extend the coverage. It can also alleviate the congestion and increase the throughput, especially applied in UAV networks. However, since the energy of UAVs is limited and the resources in UAV networks are scarce, how to optimize the network delay performance under these constraints should be well investigated. Besides, the relationship among different resources, e.g. power and bandwidth, is coupled which makes the optimization more complex. This article investigates the problem of joint power and bandwidth allocation in UAV backhaul networks, which considers both the delay performance and the resource utilization efficiency. Considering the heterogeneous locations characteristics of different UAVs, we formulate the optimization problem as a Stackelberg game. The relay UAV acts as the leader and extended UAVs act as followers. Their utility functions take both the delay durance and the resource consumption into account. To capture the competitive relationship among followers, the sub-game is proved to be an exact potential game and exists Nash equilibriums (NE). The Stackelberg Equilibrium (SE) is proved afterwards. We utilize a hierarchical learning algorithm (HLA) to find out the best resource allocation strategies, which also reduces the computational complexity. Simulation results demonstrate the effectiveness of the proposed method.

In this work, a novel silane coupled cationic precursor (SAGS) was synthesized by 3-glycidyloxypropyltrimethoxysilane and sodium 2-((2-aminorthyl)amino) ethanesulfonate. A series of cation exchange membranes were prepared with poly(vinyl alcohol) (PVA) and SAGS by sol-gel process. The structure of the prepared membranes were characterized by fourier transform infrared spectrum (FTIR) and scanning electron microscopy (SEM), and its properties were studied by water uptake (WR), cation exchange capacity (CEC), linear expansion ratio (LER), alkali stability, thermogravimetric analysis (TGA), mechanical properties and diffusion dialysis performance. FTIR and X-ray photoelectron spectroscopy (XPS）confirmed the successful preparation of SAGS membranes, and SEM images showed that the prepared membranes were dense and uniform. The WR values of the SAGS membranes were in the range of 91.49-122.39 %, and the LER values were 17.65-28.21 %. In addition, the SAGS membranes had suitable CEC value, good alkali resistance and thermal stability which ensured the application of membranes in the field of diffusion dialysis (DD) for alkali recovery. In DD test, the dialysis coefficients of NaOH (UOH) ranged from 0.012 mm/h to 0.023 mm/h, and the separation factors (S) was in the range of 30.77-16.43. In summary, the prepared membrane had good performance and simple preparation process, which had great application potential in textile industrial wastewater recovery.

Molecular hydrogen (H2) has been shown to have antioxidant and anti-inflammatory activities that may reduce the development and progression of many diseases. In this study, Hydrogen-rich water (HRW) was obtained by reacting hybrid magnesium-carbon hydrogen storage materials with water. Then the effects of intake of HRW on the activities of xenobiotic-metabolizing enzymes, membrane transporters, and oxidative stress in rats were investigated. Rats were given HRW ad libitum for 4 weeks. Results showed that intake of HRW had no significant effect on the activities of various cytochrome P450 (CYP) enzymes (CYP1A1, 1A2, 2B, 2C, 2D, 2E1, 3A, 4A), glutathione-S-transferase and UDP-glucuronosyltransferase. Except for a slight lower plasma glucose concentration, intake of HRW had no effect on other plasma biochemical parameters in rats. P-Glycoprotein and multidrug resistance-associated protein (Mrp)2 protein expressions in liver were elevated after intake of HRW. However, HRW had no significant effects on glutathione, glutathione peroxidase, or lipid peroxidation in liver. Results from this study suggest that consumption of HRW may not affect xenobiotic metabolism or oxidative stress in liver. However, intake of HRW may increase the efflux of xenobiotics or toxic substances from the liver into bile by enhancing the expression of p-glycoprotein and Mrp2 protein.

Layered 2D graphene oxide (GO) films are integrated with silicon nitride (SiN) waveguides to experimentally demonstrate an enhanced Kerr nonlinearity via four-wave mixing (FWM). Owing to the strong light–matter interaction between the SiN waveguides and the highly nonlinear GO films, the FWM performance of the hybrid waveguides is significantly improved. SiN waveguides with both uniformly coated and patterned GO films are fabricated based on a transfer-free, layer-by-layer GO coating method together with standard photolithography and lift-off processes, yielding precise control of the film thickness, placement and coating length. Detailed FWM measurements are carried out for the fabricated devices with different numbers of GO layers and at different pump powers. By optimizing the trade-off between the nonlinearity and loss, we obtain a significant improvement in the FWM conversion efficiency of ≈7.3 dB for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. We also obtain a significant increase in FWM bandwidth for the patterned devices. A detailed analysis of the influence of pattern length and position on the FWM performance is performed. Based on the FWM measurements, the dependence of GO’s third-order nonlinearity on layer number and pump power is also extracted, revealing interesting physical insights about the 2D layered GO films. Finally, we obtain an enhancement in the effective nonlinear parameter of the hybrid waveguides by over a factor of 100. These results verify the enhanced nonlinear optical performance of SiN waveguides achievable by incorporating 2D layered GO films.

Abstract: With the continuous integration of various energy systems and the reform of energy trading marketization, the traditional power demand response can no longer meet the needs of multi-energy coupling. For the joint response problem of multi-energy, this paper proposes a comprehensive demand response optimization incentive model considering the user response characteristics, with the complete energy service providers and multiple users as the participants of the comprehensive demand response, to solve the response strategy for the optimal goal of all parties. The implementation architecture of integrated demand response and the electrothermal energy hub model is introduced first. Secondly, the integrated demand response collaborative optimization strategy of the integrated energy service providers and users is established, and the existence and uniqueness of the optimal solution are proved. Finally, the example analysis demonstrates that the proposed strategy can reduce the integrated energy service providers' response cost and user dissatisfaction under multiple scenarios.

Sequential hypothesis test and change-point detection when the distribution parameters are unknown is a fundamental problem in statistics and machine learning. We show that for such problems, detection procedures based on sequential likelihood ratios with simple one-sample update estimates such as online mirror descent are nearly second-order optimal. This means that the upper bound for the algorithm performance meets the lower bound asymptotically up to a log-log factor in the false-alarm rate when it tends to zero. This is a blessing, since although the generalized likelihood ratio (GLR) statistics are optimal theoretically, but they cannot be computed recursively, and their exact computation usually requires infinite memory of historical data. We prove the nearly second-order optimality by making a connection between sequential analysis and online convex optimization and leveraging the logarithmic regret bound property of online mirror descent algorithm. Numerical and real data examples validate our theory.

Talker variability has been reported to facilitate generalization and retention of speech learning, but is also shown to place demands on cognitive resources. Our recent study provided evidence that phonetically-irrelevant acoustic variability in single-talker (ST) speech is sufficient to induce equivalent amounts of learning to the use of multiple-talker (MT) training. This study is a follow-up contrasting MT versus ST training with varying degrees of temporal exaggeration to examine how cognitive measures of individual learners may influence the role of input variability in immediate learning and long-term retention. Native Chinese-speaking adults were trained on the English /i/-/ɪ/ contrast. We assessed the trainees’ working memory and selective attention before training. Trained participants showed retention of more native-like cue weighting in both perception and production regardless of talker variability condition. The ST training group showed long-term benefit in word identification, whereas the MT training group did not retain the improvement. The results demonstrate the role of phonetically-irrelevant variability in robust speech learning and modulatory functions of nonlinguistic working memory and selective attention, highlighting the necessity to consider the interaction between input characteristics, task difficulty, and individual differences in cognitive abilities in assessing learning outcomes.

Strangeness flavor is abundant and in chemical equilibrium in the primordial Quark-Gluon Plasma(QGP) filling the early Universe. Upon hadronization near to T=150 MeV one may think that relatively short lived massive strange hadrons decay rapidly and strangeness disappears. However, we show using detailed balance considerations for inverse decay reactions that the back reaction repopulate strangeness keeping it in chemical equilibrium at least to the time when strange antibaryons annihilate near T≃30-50 MeV. However, our present study is focused on the meson sector of the hadronic Universe. Specifically, we establish here the temperature range in which the expansion of the Universe becomes faster compared to the production processes which balance natural strangeness decay: In the temperature interval 33MeV<T<20MeV: μ±+νμ→K±, π+π→K and l−+l+→ϕ reactions in sequence become slower compared to the characteristic Hubble time.

Atherosclerosis (AS) is an age-related disease. Mitochondria and telomere links have been considered to play important roles in AS. PinX1 is a potent and highly conserved endogenous telomerase inhibitor. However, the role of pinX1 in AS and its role in oxidative stress have not been reported. In order to investigate the role of pinX1 in AS, we established a classical AS mice model in the present work and increased pinX1 protein expression using pinX1 overexpression adeno-virus by tail vein injection. Then, red-oil O and HE staining were employed to evaluate the severity of AS. Serum lipid profile and oxidative stress were also detected by using its specific chemical testing kit. The results indicated that high-fat diet (HFD) markedly decreased pinX1 and increased p66shc protein expression, whereas overexpression of pinX1 protein expression in mice produced the opposite results. In addition, pinX1 significantly minimized plaque area and alleviated the abnormal serum lipid profile. By using Western blot and Biochemical assay kits, overexpression of pinX1 decreased p66shc and MMP-9 protein expression and reduced oxidative stress. This study showed pinX1 can inhibit p66shc, MMP-9, and related oxidative stress, pinX1 may be considered as a new candidate target for the treatment of AS.

Improper lifting measures of long-span spatial steel structures during construction process may delay the construction period and even cause safety accidents. Few studies on long-span spatial steel structures considered time-varying mechanical characteristic during construction process. In order to achieve safe and efficient installation in a long-span spatial steel structure, this research presents a time-varying mechanical analysis of the synchronous and asynchronous integral lifting and a single and interlaced point’s asynchronous integral lifting analysis method of a long-span spatial steel structure. The results showed that in the case of asynchronous lifting of single point, the displacement influence on other members is related to the distance. The closer the distance from the lifting point, the greater the influence. In asynchronous integral lifting, the lifting point with large lifting force is first installed to the specified position, and the lifting point with small lifting force is installed to the specified position.

An immiscible blend of poly(hydroxy ether of bisphenol-A) (phenoxy) and poly(1,4-butylene terephthalate) (PBT) with phase separation was observed in as-blended samples. However, compatibilization of the phenoxy/PBT blends can be promoted through chemical exchange reactions of phenoxy with PBT upon annealing. In contrast to the as-blended samples, the annealed phenoxy/PBT blends had a homogeneous phase with a single T_g that could be enhanced by annealing at 260°C. Infrared (IR) spectroscopy demonstrated that phase homogenization could be promoted by annealing of the phenoxy/PBT blend, where alcoholytic exchange occurred between the dangling hydroxyl group in phenoxy and the carbonyl group in PBT in the heated blends. The alcoholysis reaction changes the aromatic linkages to aliphatic linkages in carbonyl groups, which initially led to the formation of a graft copolymer of phenoxy and PBT with an aliphatic/aliphatic carbonyl link. The progressive alcoholysis reaction resulted in the transformation of the initial homopolymers into block copolymers and finally into random copolymers, which promoted phase compatibilization in blends of phenoxy with PBT. Due to the fact that the amount of copolymers increased upon annealing, crystallization of PBT was inhibited by alcoholytic exchange in the blends.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

Ganoderic Acid (GA), a major bioactive compound isolated from an oriental medicinal mushroom, i.e. Ganoderma tsugae, has traditionally been found to have significant medicinal properties. As a result of GA's poor solubility in water, formulation poses several challenges. Additionally, the traditional method of administering it via alcohol always results in unfavorable patient side effects. In order to overcome these problems, Ganoderma Tsugae extracts obtained by ethanol extraction were encapsulated in nanodispersions by ultrasonic cavitation and solvent evaporation to maximise bioavailability. Resultant nanodispersions contained Ganoderic acid in a hydrophobic core with a mean particle size of no more than 200 nm and a very narrow particle distribution. An analysis of the interactions between the control variables and the process optimisation was conducted using the Response Surface Methodology (RSM). Based on the results of the experiment, it was found that the particle size of nanodispersions was influenced by the Hydrophilic-Lipophilic Balance (HLB) number and the evaporation temperature. Moreover, the physical stability of micellar systems is generally determined by the organic phase within them. Regarding formulation stability, the zeta average of the nanodispersions remained virtually unchanged in solutions with different pH levels and short-term storage (14 days) at room temperature. Overall, it has been demonstrated that Ganoderic acid nanodispersions can be efficiently generated by combining ultrasound cavitation and solvent evaporation.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

Dielectric Elastomer Actuators (DEAs) are emerging as promising candidates for various applica-tions in robotics and optical devices due to their lightweight, miniaturization potential, high en-ergy density, simple structure, and low power consumption. However, their effective actuation always demands sophisticated high-voltage driving circuits that are compact and responsive. DEAs need to be capable of generating intricate high-voltage waveforms or simultaneously con-trolling multiple channels with distinct high-voltage levels. This paper proposes a high-voltage power supply for DEAs, featuring a four-channel high-voltage driving circuit. The circuit is ca-pable of independently generating high-voltage signals ranging from 100 V to 6000 V and can be programmed to produce arbitrary waveforms with adjustable frequencies. The independent op-eration of channels without crosstalk showcases the system's integration and potential for cross-disciplinary applications.

We employed the Riemannian Face Manifold (RFM) as an alternative approach to the conventional linear Euclidean space for explaining the atypicality bias in face likeliness judgments. The RFM posits that the mental representation of faces is better captured as a manifold of stable states, accounting for the nonlinearity in the physical properties of faces. To examine the relationship between physical and psychological distance of morph and typical/atypical faces, we manipulated the parameter k and incorporated a weight function in the Riemannian metric. Our results indicate that the psychological distance between the morph and typical face was longer than that between the morph and atypical face, consistent with prior research on the atypicality bias in perceptual similarity. The RFM approach provides mathematical support and is a powerful tool for studying face perception and recognition, offering potential implications for explaining the other-race effect. Future research can utilize the RFM to investigate individual differences in face recognition abilities and expertise, and how they impact psychological distance and face processing.

High-rise building fires pose a serious threat to the lives and property safety of the people. The lack of reliable and accurate positioning means is one of the main difficulties faced by rescue. In the absence of prior knowledge of the high-rise building fire environment, the coverage deployment of mobile base stations is a challenging problem that has not received much attention in the literature. This paper studies the problem of autonomous optimal deployment of base stations in high-rise building fire environment based on UAV group. A novel problem formulation is proposed that solves the non line of sight (NLOS) positioning problem in complex unknown environment. The purpose of this paper is to realize the coverage and deployment of mobile base stations in complex and unknown fire environment. The NLOS positioning problem in the fire field environment is turned into the line of sight (LOS) positioning problem through the optimization algorithm. And there are more than three LOS base stations nearby any point in the fire field. A control law which is formulated in a mathematically precise problem statement is developed that guarantees to meet mobile base stations deployment goal and to avoid collision. Finally, positioning accuracy of our method and that of common method were compared. The simulation result showed that the positioning accuracy of simulated firefighter in the fire field environment was improved greatly.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

The utilization of smart IoT devices, commonly referred to as digital twins, is aimed at the digitalization of human knowledge within aquaculture processes. This involves the incorporation of cutting-edge technologies, including information-based management with big data and modeling, to automate machinery and gain comprehensive insights into the aquaculture environment and fish farm conditions. The ultimate objective is to empower farmers to make informed decisions, furnishing them with objective data to enhance their capacity in monitoring and controlling the various factors impacting fish production. As a result, farming decisions can be fine-tuned to enhance fish health and optimize farm output. In the context of large and modern aquaculture farms, technological innovation becomes imperative to automate processes, minimize labor requirements, and streamline fish feeding operations. Remarkably, the literature currently offers limited discussions on the digital transformation of aquaculture through the application of digital twin methodologies. A prior study underscores the critical influence of factors such as market prices and fish survival rates on the profitability of offshore caging culture. In this study, we embark on an analysis of the prerequisites for establishing a digital twin infrastructure tailored to intelligent fish feeding management. This infrastructure is designed to facilitate the integration of technology and data-driven decision-making, ultimately enhancing the efficiency of fish feeding processes. The proposed architecture for the fish feeding digital twin encompasses various digital twin components, encompassing water quality forecasting, fish population assessment, fish metrics estimation, fish feed prediction, and evaluation of fish feeding intensity. Furthermore, we optimize the daily fish feeding process through reinforcement learning algorithms. Finally, we implement a cloud-based AIoT system that provides the runtime environment for executing digital twins and controlling our intelligent fish feeding machinery. Experimental findings underscore the efficacy of the proposed digital twin system in significantly improving traditional fish feeding processes, notably in terms of reducing food costs and labor requirements.

In recent years, the emergence of spatiotemporal big data has made the transition of functional identification from the physical dimension to socioeconomic or human activities becoming more common. In the identification of urban functional areas, most studies considered only a single data source and a single division scale, the research results have problems such as low update frequency or incomplete information in a single data set, and overfitting or underfitting in a single spatial resolution. Using taxi trajectory data and point of interest (POI) data as the main data source, this study proposes a multi-scale recursive identification method for urban functional areas based on cross-validation. First, used the dynamic time warping (DTW) algorithm generates a time series similarity matrix, the CA-RFM model combines the clustering algorithm and random forest model is constructed, the model uses a clustering algorithm (K-MEDOIDS) to extract sig-nificant feature regions as input, which are imported into the random forest model for UFZ identification. Then, to overcome the shortcomings of single scale in expressing urban structural characteristics, a recursive model of different levels of urban road networks is established to classify multi-scale functional areas. Finally, cross-validation using the CA-RFM model and POI quantitative identification method, obtains the final identification results of urban functional areas. This paper selects Shenzhen as the study area for the case study, the results show that the com-bination of clustering algorithm and random forest model greatly reduces the error of manual selection of training samples. In addition, the research shows the superiority of the multi-scale recursive identification method that fuses multi-source data and performs cross-validation from two aspects, that is, the division speed of urban functional area identification results is accelerated and the accuracy is improved.

In the first part of this talk we review some prerequisites for and essential arguments involved in the construction of the thermal-ground-state estimate for the deconfining phase in the thermodynamics of SU(2) Quantum Yang-Mills theory and how this structure supports its distinct excitations. The second part applies deconfining SU(2) Yang-Mills thermodynamics to the Cosmic Microwave Background in view of (i) a modified temperature-redshift relation with an interesting link to correlation-length criticality in the 3D Ising model, (ii) the implied minimal changes in the dark sector of the cosmological model, and (iii) best-fit parameter values of this model when confronted with the spectra of the angular two-point functions TT, TE, and EE, excluding the low-$l$ physics. The latter, which is treated in an incomplete way because of the omission of radiative effects, is addressed in passing towards future work.

Quantum coherence is an important physical resource in quantum information science, and also as one of the most fundamental and striking features in quantum physics. In this paper, we obtain a symmetry-like relation of relative entropy measure $C_r(\rho)$ of coherence for $n$-partite quantum states $\rho$, which gives lower and upper bounds for $C_r(\rho)$. Meanwhile, we discuss the conjecture about the validity of the inequality $C_r(\rho)\leq C_{\ell_1}(\rho)$ for any state $\rho$. We observe that every mixture $\eta$ of a state $\rho$ satisfying $C_r(\rho)\leq C_{\ell_1}(\rho)$ and any incoherent state $\sigma$ also satisfies the conjecture. We also note that if the von Neumann entropy is defined by the natural logarithm $\ln$ instead of $\log_2$, then the reduced relative entropy measure of coherence $\bar{C}_r(\rho)=-\rho_{\rm{diag}}\ln \rho_{\rm{diag}}+\rho\ln \rho$ satisfies the inequality ${\bar{C}}_r(\rho)\leq C_{\ell_1}(\rho)$ for any mixed state $\rho$.

Quinoa, known as the "golden grain" for its high nutritional value, is a significant source of essential nutrients, including proteins, minerals, vitamins, polyphenols, phytosterols, and flavonoids. However, the biological functions of quinoa polysaccharides remain understudied. In this research, two crude quinoa polysaccharides extracts (Q-40 and Q-60) were obtained extracting by 40% and 60% alcohol. The purity of Q-40 and Q-60 was 58.29% and 62.15%, with protein contents of 8.27% and 9.60%, respectively. Monosaccharide analysis revealed that Q-40 contained glucose (Glc), galacturonic acid (GalA), and arabinose (Ara) in a molar ratio of 0.967:0.027:0.006. Q-60 was composed of xylose (xyl), arabinose (Ara), galactose, and galacturonic acid (GalA) with a molar ratio of 0.889:0.036:0.034:0.020. The average molecular weight of Q-40 ranged from 47484 to 626488 Da, while Q-60 showed a range of 10025 to 47990 Da. Rheological experiments showed that Q-40 exhibited higher viscosity, while Q-60 demonstrated more elastic properties. Remarkably, Q-60 showed potent antioxidant abilities, with scavenging rates of 98.49% for DPPH and 57.5% for ABTS. Antibacterial experiments using the microdilution method revealed that Q-40 inhibited the growth of Methicillin-resistant Staphylococcus aureus (MRSA) and E. coli, while Q-60 specifically inhibited MRSA. At lower concentrations, both polysaccharides inhibited MDA cell proliferation, but at higher concentrations, they promoted proliferation. Similar proliferation-promoting effects were observed in HepG2 cells. The research provides important information in application of quinoa in food and functional food industries.

The United Nations' sustainable development goals have underscored the importance of enhancing supply chain sustainability while appropriately distributing orders. This study proposes a novel framework involving Z-number, game theory, indifference threshold-based attribute ratio analysis (ITARA), and combined compromise solution method (CoCoSo) to evaluate the sustainability of suppliers and order allocations. To better reflect the decision makers’ current choices for the sustainability of assessed suppliers and order allocations; enhance the comprehensiveness of decision-making, the importance parameter of the supplier is obtained through game theory objectively for transforming supplier performance into order allocation performance. The Z-numbers are involved in ITARA (so-called ZITARA) and CoCoSo (so-called ZCoCoSo) to overcome the issue of information uncertainty in the process of expert evaluation. ZITARA and ZCoCoSo are applied to assess the objective weight of criteria and the ranking of assessed order allocations, respectively. Afterwards, a case study of China’s company is illustrated the utility of the proposed framework and inform their decision-making process regarding the orders to be assigned to the assessed suppliers.

We present set-theoretical solutions of the Yang-Baxter equation in BCK–algebras. Some solutions in BCK−algebras are not solutions in other structures (such as MV −algebras). Related to our investigations we also consider some new structures: Boolean coalgebras and a unified braid condition – quantum Yang-Baxter equation. Finally, we will see how poetry has accompanied the development / history of the Yang–Baxter equation.

The investigation aims to analyze the effect of homogenization heat treatment on the quantity, distribution, morphology, and chemical composition of δ ferrite and sigma phase in the 316L austenitic stainless steel cast billet. Microstructures of the cast billet at different locations, center, 0.5 R, R, and the subsequent 2/6-hour homogenization heat treatment at 1240 oC were examined. The microstructure at the radius R was much more uniform and expected a better performance in the following hot/cold forging processes due to the highest cooling rate compared with those at 0.5R and center. The δ ferrite often accompanies the generation of the sigma phase, and the transformation of δ ferrite into the sigma/(austenite) and retained δ ferrite is strongly related to the cooling rate after homogenization heat treatment. The sigma phase is hard and detrimental to the subsequent hot/cold forgings. It must be removed from the homogenization heat treatment before forging. Fast air cooling from 850 oC to room temperature after homogenization heat treatment cannot prohibit the sigma phase formation. Rapid cooling between 850 and 1240 oC after homogenization treatment is required to avoid the sigma phase formation in the 316L stainless steel cast billet.

Patients with end stage liver disease (ESLD) undergoing liver transplantation are prone to thromboses both while on the waiting list or in the perioperative period. This hypercoagulability is associated with significant endothelial dysfunction (ED) due to nitric oxide dysregulation. ED in combination with increased thrombin generation are the main factors responsible for this hypercoagulability. Sepsis itself can significantly change the coagulation profile, but in combination with ESLD, sepsis, and septic shock is responsible for very complex changes in the patients coagulation making both assessment and management of coagulation in patients with ESLD very challenging. Viscoelastic testing (VET) is a preferred method of coagulation management in patients with cirrhosis because, as with standard laboratory testing, VET can assess the entire coagulation system including the interaction between both pro- and anticoagulants and platelets.

The rank-3 antisymmetric tensors which are the magnetic monopoles of SU(N) Yang-Mills gauge theory dynamics, unlike their counterparts in Maxwell’s U(1) electrodynamics, are non-vanishing, and do permit a net flux of Yang-Mills analogs to the magnetic field through closed spatial surfaces. When electric source currents of the same Yang-Mills dynamics are inverted and their fermions inserted into these Yang-Mills monopoles to create a system, this system in its unperturbed state contains exactly 3 fermions due to the monopole rank-3 and its 3 additive field strength gradient terms in covariant form. So to ensure that every fermion in this system occupies an exclusive quantum state, the Exclusion Principle is used to place each of the 3 fermions into the fundamental representation of the simple gauge group with an SU(3) symmetry. After the symmetry of the monopole is broken to make this system indivisible, the gauge bosons inside the monopole become massless, the SU(3) color symmetry of the fermions becomes exact, and a propagator is established for each fermion. The monopoles then have the same antisymmetric color singlet wavefunction as a baryon, and the field quanta of the magnetic fields fluxing through the monopole surface have the same symmetric color singlet wavefunction as a meson. Consequently, we are able to identify these fermions with colored quarks, the gauge bosons with gluons, the magnetic monopoles with baryons, and the fluxing entities with mesons, while establishing that the quarks and gluons remain confined and identifying the symmetry breaking with hadronization. Analytic tools developed along the way are then used to fill the Yang-Mills mass gap.

Questions：SAP in mountainous cities of China serve as crucial carriers for species and wild food, constituting potential green infrastructure. These patches should be recognized as locally specific resources. This study investigates the transformation characteristics of the landscape patterns of SAP, along with their elements, across urban-rural gradients, providing foundational support for the planning of conservation and utilization strategies. Location: Yongchuan area of Chongqing in southwest China. Methods: The study investigated urban-rural gradient-based transformation of SAP. A four-direction transect space was selected and divided into uniform sample squares. Fragstats 4.3 calculated the landscape index of SAP, and Spearman correlation coefficients in SPSS were used to evaluate the influence of landform and artificial factors on agroforestry patch transformation. Results: 1) Patch area (PA), Plaque density (PD), and CLUMPY of SAP systematically transform, showing increased SAP areas and higher connectivity with greater distance from the city, resulting in reduced patch fragmentation. However, Edge density (ED) and Largest plaque index (LPI) exhibit irregular transformation patterns. 2) With increased distance from the city, woodland patch area and connectivity increase, leading to decreased fragmentation, dispersal, and lower fractal dimensions. Conversely, Cultivated land follows the opposite trend. garden land patch area, fractal dimension, fragmentation, and dispersal all increase, while connectivity decreases. 3) Landscape pattern transformations of SPA are significantly influenced by artificial factors. Woodland patches are influenced similarly by landform and artificial factors. In contrast, cultivated land and garden land patches are more significantly impacted by artificial factors. Conclusions: SAP exhibit differentiated conservation and utilization measures across urban-rural gradients. Small patches located far from urban centers may benefit from systematic conservation measures to prevent further fragmentation and erosion in peri-urban areas.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

In this study, a composite flame retardant was created by combining fish scale (FS), fishery waste, and ammonium polyphosphate (APP), a commercially available flame retardant. The composite flame retardant was added to epoxy resin (EP) to form an EP/APP/FS composite that prevents burns and is environmentally friendly. The use of FS conforms to the concept of circular economy and lowers costs by reducing the consumption of APP. Thermogravimetric analysis (TGA), integral procedural decomposition temperature (IPDT), pyrolysis kinetics, limiting oxygen index (LOI), the Underwriters Laboratories 94 (UL94) flammability test, scanning election microscopy, Raman spectroscopy, and energy-dispersive X-ray spectroscopy were used to determine the thermal properties, flame retardant properties, flame retardant mechanism, char morphology, and composition of the composites. The TGA results indicated that the addition of 40% flame retardant raised the char residue from 16.45 wt% (pure EP) to 36.07 wt%, IPDT from 685.6 °C (pure EP) to 1143.1°C, LOI from 21% (pure EP) to 30%, and UL94 classification from fail (pure EP) to V-0. These results suggest an increase in char residue, which indicates better protection of the polymer matrix material. The improvements in IPDT, LOI, and UL94 classification, which indicate greater thermal stability, lower flammability (from flammable to fireproof), and higher flammability rating (from fail to V-0), respectively, suggest that the composite material has favorable thermal properties and is less inflammable.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

With the global warming and the frequent occurrences of harsh environments, mooring line failures are frequent. Response analysis of the platform structure and its residual mooring system under multiple mooring line failures is needed. Therefore, it is necessary to investigate the change law of platform motion response after mooring line failure to find out the reasons for the change. Studies for different failure combinations of mooring lines show that the variation of the steady-state equilibrium position of the platform is closely related to the stiffness, with a clear functional. The duration and amplitude of the transient response are mainly influenced by the Morison drag force. And it was found that the suspended mooring line reduced the motion responses. It is also found that the mooring line failure increased the effective tension and suspension length of the riser. Based on the improved Dezert-Smarandache theory (DSmT), it is calculated that mooring line failure has little effect on the failure probability in different zones of the riser.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

As the leader of the largest economy, President of the United States has substantive influence on addressing the global climate change problem. However, presidential election is often dominated by issues other than energy problems. This paper focuses on the on-going 2016 presidential election, examining the energy plans proposed by the leading Democrat and Republican candidates. Our data from the Iowa caucus survey in January 2016 suggests that voters are more concerned about terrorism and economic issues than environmental relative issues. We then compare the Democratic and Republican candidate’s view of American’s energy future, and evaluate their proposed renewable energy targets. We find that the view on renewable energy is polarized between Democratic and Republican candidates, while candidates from both parties agree on the need for energy efficiency. Results from our ordinal least squares regression models suggest that Democratic candidates have moderate to ambitious goals for developing solar and other renewable energy. The Republican candidates favor fossil fuel and they neglect to provide any plan for renewable energy. In addition, this trend of polarization has grown more significant when compared with the past three presidential elections. Our observation suggests that energy issues need to be discussed more to draw broader attention to salient issues of diversifying and decarbonizing the nation’s energy system.

Saline soil from the coast is a valuable resource that is readily available. It is also a valuable resource for reserving arable land. It has been demonstrated that adding organic fertilizers to salinized soils can effectively enhance them. However, since the improvement of saline soils cannot be achieved by a single measure, the effects of compound measures of organic fertilizers combined with mineral elements, humic acid, are significant and might be examined in depth. In order to explore the effects of various measures on the features of pH, electrical conductivity (EC), and nutrient changes in coastal salinized soils in Yancheng, Jiangsu Province, a ryegrass-alfalfa rotation with organic fertilizer as well as compound measures was designed. The findings indicated that the total nitrogen (TN) content of the soil increased and that all organic fertilizer composites decreased the electrical conductivity of the surface soil. However, the organic fertilizer with microbial fertilizer and humic acid was especially effective at regulating the pH and electrical conductivity of the surface soil during the time when salts were prone to accumulating. In conclusion, our findings point to new approaches to lowering salinity and boosting fertility in coastal saline soils: organic fertilizer with microbial fertilizers and humic acid, as well as organic fertilizer with Attapulgite clay.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

To elucidate the chemical compositions of the sugar fall maple leaves, the methanol extracts were firstly fractionated by ethyl acetate and n-butanol respectively. The phenolic acids-rich fractions (ethyl acetate extracts) were further purified by various chromatographic columns including XAD macroporous resin, Sephadex LH-20, ODS and semi-preparative HPLC to yield the compounds. The isolated compounds were characterized by ¹H-Nuclear Magnetic Resonance (¹H-NMR), ¹³C-NMR, and high resolution electrospray ionisation mass spectral (HR-ESI-MS) spectroscopy. Twenty eight phenolics including fourteen flavonoids (1-14), five quinic acid derivatives (15-19), five galloyl tannins (20-24) and four other phenolic acids (25-28) were isolated and their structures were identified. The isolated compounds were evaluated for their antioxidant and α-glucosidase inhibitory activities. All of the phenolics constituents showed DPPH scavenging antioxidant activities. While, glycosides of quercetin and myricetin, galloyl tannins were showed promising α-glucosidase inhibitory activity. All of the compounds except 4, 11, 12 and 28 were isolated from sugar maple for the first time. Moreover, Compounds 9, 10, 14, 20, 21, 23, 25 and 26 were isolated from the Acer species for the first time.

The prefabricated ECC/RC combined shear wall structure is an innovative prefabricated composite structure with better seismic performance by using ECC materials with better ductility in the main force and energy consumption regions of the prefabricated reinforced concrete (RC) shear wall structure. The key factors controlling the seismic energy dissipation capacity of this kind of structure are the use regions of ECC in composite coupling beams, use regions of ECC in shear walls, strength of ECC, stirrup ratio of coupling beams, strength of longitudinal reinforcement and so on. The parameters affecting seismic energy consumption are quantified by the finite element analysis method. By comparing and analyzing the load-displacement curves, hysteresis curves, energy dissipation capacity and stiffness degradation of the prefabricated ECC/RC combined shear wall structure specimen under these parameters, it is proposed that the best use regions of ECC is the cast-in-situ zone of the coupling beams with the scope of no more than400 mm at the shear walls’ bottom. The strength grade, the strength grade of longitudinal reinforcement, and the stirrup ratio of coupling beams are suggested design as E40, HRB400 and 0.5%, respectively.

Multicellular organisms organize themselves according to two principles; first, the equilibrium between the driving force of unstable state cells and apoptosis or senescence; and second, the mutual equilibrium between the functional requirements of different types of cells. For the first principle, we deduce that stem cells at different levels have their own growth limits, which are determined by two factors: the ability of the stem cells to enter an unstable state (specifically, the ability of cells to divide and differentiate); and the rate of cellular senescence, loss of function, and finally, apoptosis. The superposition of stem cell limits at different levels over each other can amplify small differences at the genetic level. Moreover, the growth limits of different organs are different, which lead to different individuals having completely different appearances. The second principle is that the sum of the specific output functions of an organ must be equal to the overall demand for the function to be provided by the organ. If negative entropy input can meet this equilibrium, defects in certain genes will cause these defective individuals to become larger or develop other morphology.

EGFR mutations are heterogenous but all carry the same weighting in the Lung-molGPA. The aim of this study was to elucidate the different prognostic implications of molecular subtypes and frontline TKIs in EGFR-mutated lung adenocarcinoma with synchronous brain metastases (BM) using the Lung-molGPA. Medical records were searched in hospital databases from 2011 to 2015. Patients with EGFR-mutated adenocarcinoma and brain metastases who received TKIs were included. The Kaplan-Meier method was used to estimate survival, and multivariate Cox proportional hazard models were used to estimate adjusted hazard ratios (HRs) and 95% confidence intervals (CIs). A total of 256 patients were included with a median overall survival (OS) of 17.2 months. In multivariate analysis of OS, only age (70 versus <70 years, HR:1.71, 95% CI:1.25-2.35, p<0.001), KPS (<70 versus 70, HR:1.71, 95% CI:1.26-2.31, p<0.001), and rare mutations (other versus exon 19 deletions, HR:1.78, 95% CI:1.04-3.05, p=0.037) remained statistically significant. In patients with a Lung-molGPA score 2.5, EGFR molecular subtypes had different median OS (exon 19 deletions versus Leu858Arg versus other, 18.8 vs 12.4 vs 12.1 months, p=0.021). In conclusion, different molecular subtypes treated with frontline TKIs have different prognostic implications in the Lung-molGPA. Further prospective studies are warranted to validate these findings.

In view of the limitations of the existing eccentricity error separation method of the rotary table, an eccentricity error separation method based on the phase feature of the moiré signal of single reading head is proposed herein. A grating pair transmission model is established based on the analysis of the principle of the rotary table, thereby the influence of eccentricity error on the phase feature of the moiré signal in the rotation course of the rotary table is clarified, and the corresponding model between the phase feature spectral components and the eccentricity error is established. The verification experiments of the proposed method are carried out based on the laboratory-made circuit system. After verifying the accuracy of the data acquisition of the laboratory-made circuit board, the verification experiments of the eccentricity error separation effect of the proposed method are carried out. The experimental data are compared with those of the traditional method and the results show that the error between the two methods is 2.34μm and the relative error is 2.3%.

Understanding and evaluating urban investment environment is essential for effectively improving the efficiency of resource allocation between cities and promoting overall development of the regional economy. This paper takes 15 node cities on maritime Silk Road covered by the “Belt and Road” as the research object, establishes a dynamic evaluation index system for investment environment, and uses projection pursuit cluster to analyze and evaluate the investment environment of the cities. It is found that the investment environment potential of a city is directly related to the level of social development, economic development, and the degree of opening to the outside world. It is recommended that node cities should seize the important opportunity of the construction of the Maritime Silk Road, introduce world-wide human, financial and material resources to promote regional resources allocation and flow, and continuously improve and upgrade the investment environment quality.

A dual-platform colorimetric and ratiometric chemosensor, namely 6-(2-hydroxynaphthalen)-N-n-butyl-naphthalimide (HNA), based on Schiff base constructed from N-n-butyl-4-amino-1,8-naphthalimide and 2-hydroxy-1-naphthaldehyde has been designed and fabricated for detecting fluoride anion (F−) in DMSO solution. HNA is a colorimetic and ratiometric probe with superior selectivity and sensitivity. The color changes of HNA from yellow to purple was observed by the naked eyes in the presence of F−. The absorbance in the UV-Vis spectra of HNA was decreasing in 422 nm, while gradually increasing in 583 nm by adding F−. The limit of detection (LOD) of HNA for detecting F− is low to 0.61 μM and the binding model of HNA and F− is in 3:2 stoichiometry. Meanwhile, HNA can be used to detect F− in real samples. Finally, the mechanism of HNA for the detection of F− was investigated. The present work indicated that HNA would be a superior potential chemosensor in monitoring F− selectively and sensitively.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

In this paper, we investigate a class of hierarchical variational inequalities (HVIPs, i.e., strongly monotone variational inequality problems defined on the solution set of multiple-set split common fixed point problems) with quasi-pseudocontractive mappings in real Hilbert spaces, which special cases can be found in many important engineering practical applications such as image recognizing, signal processing and machine learning. In order to solve HVIPs of potential application value, inspired by the primal-dual algorithm, we propose a novel accelerated cyclic iterative algorithm that combines the inertial method with a correction term and a self-adaptive step-size technique. Our approach eliminates the need for prior knowledge of the bounded linear operator norm. Under appropriate assumptions, we establish strong convergence of the algorithm. Finally, we apply our novel iterative approximation to solve multiple-set split feasibility problems and verify the effectiveness of the proposed iterative algorithm through numerical results.

Xaa-Pro dipeptidase (XPD, EC 3.4.13.9; also known as prolidase) catalyzes the hydrolysis of iminopeptide bond in the trans Xaa-Pro dipeptides (Xaa represents any amino acid except proline), which makes it find wide applications in food, medical and environmental protection fields. In the present study, a novel Xaa-Pro dipeptidase from Aspergillus phoenicis ATCC 14332 (ApXPD) was molecularly and biochemically characterized. Reclassification based on phylogenetic analysis and version 12.5 MEROPS database showed that this enzyme was the only fungal XPD in the unassigned subfamily which shared the highest sequence similarity with Xanthomonas campestris prolidase but not with that from the more related fungal species A. niudulans. As compared with other prolidases, ApXPD also contained an N-terminal tail (residues 81-89) and an additional region (PAPARLREKL), and used a different arginine residue for dipeptide selectivity. After heterologous expression and partial purification, recombinant ApXPD was highly active and stable over the alkaline range from 8.5 to 10.0, with a maximum activity at pH 9.0 and more than 80% activity retained after 1-h incubation at pHs of 8.5-10.0 (55oC). It also had an apparent optimum temperature of 55oC and remained stable at 20-30oC. Moreover, this enzyme was a cobalt dependent prolidase that only cleaved dipeptides Lys-Pro, Gly-Pro and Ala-Pro rather than other dipeptides, tripeptides and tetrapeptides. All these distinct features make A. phoenicis ATCC 14332 XPD unique among currently known prolidases, thus defining a novel Xaa-Pro dipeptidase subfamily.

Objectives. Invasive fungal spondylodiscitis (IFSD) is rare and could be lethal in certain circumstances. Previous literature revealed limited data concerning the outcomes. This study aimed to establish a risk-scoring system. Methods. A total of 53 patients were included in the study from a multi-centered database in Taiwan. All the clinicopathological and laboratory data were retrospectively analyzed. Variables strongly related to 1-year mortality were identified using a multivariate Cox proportional hazards model. A receiver operating characteristic curve was used to express the performance of our IFSD scoring model. Results. Five strong predictors were included in the IFSD score: predisposing immunocompromised state, the initial presentation of either radiculopathy or myelopathy, initial laboratory findings of WBC > 12.0 or < 0.4 103/uL, hemoglobin < 8 g/dL, and evidence of candidemia. 1-year mortality rates for patients with IFSD Scores of 0, 1, 2, 3, and 4 were 0%, 16.7%, 56.3%, 72.7%, and 100%, respectively. The area under the curve of the receiver operating characteristic curve was 0.823. Conclusions. We developed a practical scoring model with easily obtained demographic, clinical, and laboratory parameters to predict the probability of 1-year mortality in patients with IFSD. However, more large-scale and international validations would be necessary before this scoring model is commonly used.

(1) Background: Bacterial reinfection and root fracture are the main culprits related to root canal treatment failure. This study aimed to assess the utility of quercetin solution as an adjunctive endodontic irrigant that strengthen root canal dentin with commitment anti-biofilm activity and bio-safety. (2) Methods: Based on a noninvasive dentin infection model, dentin tubules infected with Enterococcus faecalis (E. faecalis) were irrigated with sterile water (control group), and 0, 1, 2, 4 wt% quercetin-containing ethanol solutions. The live and dead bacteria proportions within E. fae-calis biofilms were analyzed using confocal laser scanning microscopy (CLSM). Elastic modulus and hydroxyproline release and X-ray photoelectron spectroscopy (XPS) characterization was tested on irrigant-treated demineralized dentin to evaluate irrigants’ biostability. The cytotoxicity of irrigants was tested by CCK-8 assay. (3) Results: Quercetin increased the proportion of dead bacteria volumes within E. faecalis, and improved the flexural strength of dentin collagen com-pared to control group. The XPS characterization revealed an increase in C-O peak area under both C1s and O1s narrow-scan spectra. The CCK-8 assay confirmed no cytotoxicity of quercetin solutions. (4) Conclusions: Quercetin exhibited anti-biofilm activity, collagen-stabilizing effect as well as cytocompatibility, supporting quercetin as a potential candidate for endodontic irrigant.

Background: Estrogen homeostasis is crucial for bladder function, and estrogen deprivation resulting from ovarian removal or ovarian dysfunction may lead to various bladder dysfunctions. However, the specific mechanisms are not fully understood. Methods: We simulated estrogen deprivation using a rat ovariectomy model and supplemented estrogen through subcutaneous injections. The metabolic characteristics of bladder tissue were analyzed using non-targeted metabolomics, followed by bioinformatics analysis to preliminarily reveal the association between estrogen deprivation and bladder function. Results: We successfully established a rat model with estrogen deprivation and, through multivariate analysis and validation, identified several promising biomarkers represented by 3, 5-tetradecadiencarnitine, lysoPC (15:0), and cortisol. Furthermore, we explored estrogen deprivation-related metabolic changes in the bladder primarily characterized by amino acid metabolism imbalance. Conclusions: This study, for the first time, depicted the metabolic profile of bladder resulting from estrogen deprivation, providing an important experimental basis for future research on bladder dysfunctions caused by estrogen deprivation.

Predicting trip purpose from comprehensive and continuous smart card data is beneficial for transport and city planners in investigating travel behaviours and urban mobility. Here we propose a framework, ActivityNET, using machine learning (ML) algorithms to predict passengers’ trip purpose from smart card data and Points-of-Interest (POIs) data. The feasibility of the framework is demonstrated in two phases. Phase I focuses on extracting activities from individuals’ daily travel patterns from smart card data and combining them with POIs using the proposed ‘activity-POIs consolidation algorithm’. Phase II feeds the extracted features into an artificial neural network (ANN) with multiple scenarios and predicts trip purpose under primary activities (home and work) and secondary activities (entertainment, eating, shopping, child drop-offs/pick-ups and part-time work) with high accuracy. As a case study, the proposed ActivityNET framework is applied in Greater London and illustrates a robust competence to predict trip purpose. The promising outcomes demonstrate that the cost-effective framework offers high predictive accuracy and valuable insights into transport planning.

Compounds with tyrosinase inhibitory efficacy could be effective as depigmenting agents. Although a large number of natural and synthetic tyrosinase inhibitors have been reported, few of them are used as skin-whitening agents due to poor activity and safety concerns. 3-(2,4-Dihydroxyphenyl)propionic acid (DPPA), a naturally occurring compound isolated from Ficus carica, was previously discovered as a moderate tyrosinase inhibitor. In this study, the structure-activity relationship study of DPPA was conducted. Compound 3g, with the 2,4-resorcinol subunit and terminal hydrophobic di-butylamino group, was identified with low nanomolar enzymatic IC₅₀ value. Additionally, compound 3g could effectively reduce melanin levels in B16-F10 melanoma cells treated with α-melanocyte-stimulating hormone (α-MSH) without affecting cell viability and proliferation. All these results indicated that compound 3g could be considered as a promising candidate for the treatment of diseases associated with hyperpigmentation.

Our previous retrospective observational study demonstrated the safety of laparoscopically assisted subtotal colectomy with ileorectal anastomosis and preservation of the superior rectal artery (SRA), without instances of leakage, in patients with slow-transit constipation (STC). Thus, we extended the enrollment period and enlarged the sample size to detect the differences in the post-operative complications, and surgical and functional outcomes between patients who underwent laparoscopically assisted subtotal colectomy with and without SRA preservation. We conducted a retrospective single-center analysis of patients with STC who underwent laparoscopically assisted subtotal colectomy between 2016 and 2020. The diagnosis of STC was based on the colonic transit and anal functional tests, and barium enema to exclude secondary causes. Patients were divided into group A that underwent surgery with SRA preservation, and group B that underwent ligation of the SRA during surgery. Outcome assessments for both groups included the incidence of anastomotic breakdown, intraoperative complications, length of hospital stay, estimated blood loss, time to first flatus, and complications. Propensity-score matching allocated 34 patients to groups A and B each. Postoperative bowel function, including time to first flatus, stool, and oral intake, recovered better in group A than that in group B. Anastomotic leakage, a significant postoperative complication, was less frequent in patients with SRA preservation. Preservation of the SRA in patients undergoing laparoscopically assisted subtotal colectomy with ileorectal anastomosis for STC is associated with favorable postoperative bowel function recovery and lower anastomotic leakage rates.

Marek’s disease (MD) is an important neoplastic disease caused by serotype 1 Marek's disease virus (MDV-1), which results in severe economic losses worldwide. Despite vaccination practices that have controlled the MD epidemic, current increasing MD-suspected cases indicate the persistent viral infections circulating among vaccinated chicken farms in many countries. However, the lack of available information about phylogeny and molecular characterization of circulating MDV-1 field strains in Taiwan reveals a potential risk in MD outbreaks. This study investigated the genetic characteristics of 18 MDV-1 isolates obtained from 17 vaccinated chicken flocks in Taiwan between 2018 and 2020. Based on the sequences of the meq oncogene, phylogenetic analysis demonstrated that the circulating Taiwanese MDV-1 field strains were predominantly in a single cluster that showed high similarity with strains/isolates from countries of East Asian region. Because the isolated strains were obtained from CVI988/Rispens vaccinated chicken flocks and the molecular characteristics of the Meq oncoprotein showed the features like vvMDV and vv+MDV strains, the circulating Taiwanese MDV-1 field strains may have higher virulence compared with vvMDV pathotype. In conclusion, the presented data demonstrate the circulation of hypervirulent MDV-1 strains in Taiwan and highlight the importance of routine surveillance and precaution strategies in response to the emergence of enhanced virulent MDV-1.

Photodynamic therapy has been applied endoscopically to treat early esophageal cancer. However, the long-term survival outcome of this treatment option is unknown in literature. Patients and Method: The patients of early esophageal cancer (clinical stage I) treated with photophrin based photodynamic therapy were analyzed for their long-term survival outcome and compared to those patients undergoing esophagectomy by a single surgeon for stage I disease. Results: There were 15 and 16 patients undergoing PDT and esophagectomy enrolled in the current study respectively. Complete response was achieved in 10 (66.7%) patients after PDT. After adjuvant chemoradiation (CCRT) complete response was achieved in 13 patients (86%). There is no mortality after PDT. Severe complication was detected in 3 patients including trachea-esophageal fistulae, esophageal stenosis and skin photosensitivity respectively. With a median follow-up duration of 110.2 months (+9.6 months) for the patients after PDT, there were 4 and 3 recurrence in the primary tumor site and regional lymph node respectively with 73.3% of successful local control rate of the primary tumor. There were 7 (46.7%) patients died during clinical follow-up of this cohort with 5 (33.3%) from disease progression of esophageal cancer and two from other diseases respectively. The five-year survival rate after PDT is 64.3%, whereas 70.9% of the patients after esophagectomy without significant difference of these two group of patients (P=0.72). Conclusion: Our preliminary results suggested that PDT might provide an equivalent long-term oncological outcome as compared to that done by esophagectomy for early esophageal cancer. A prospective randomized clinical trial comparing the results with esophagectomy and other endoscopic abrasive therapies is warrant in the future.

The color changes corresponding to chromophore structures in lignin caused by exposure of Eucalyptus（Eucalyptus grandis and E. urophylla）to heat were investigated. Eucalyptus wood samples were heated in saturated steam atmospheres for 10 h at 110℃, 130℃, and 150℃. The lignin was isolated before and after heat treatment. The physicochemical properties of the lignin and changes in chromophore structures during heat treatment was evaluated through wet chemical analysis, FTIR, UV-Vis, GPC, XPSand 13C-NMR. The color of the wood became darker and redder with the increase in pressure and temperature. Depolymerization and dehydration reactions occurred via demethoxylation with heat treatment in saturated steam at 110℃ or 130℃. Lignin condensed to form insoluble compounds after heat treatment in saturated steam at 150℃. G units increased and S units decreased through demethylation during heat treatment, as revealed by FTIR and 13C-NMR analysis.

Simply Summary: Translation of new cancer treatments between pets and human were noticed in comparative oncological investigation. The current study aims at evaluating a polyacetylenic glucoside purified from an edible herb, Bidens pilosa, to present its anti-angiogenic effects. We innovatively find this polyacetylenic glucoside, cytopiloyne, shows anti-angiogenic effect on different in vitro assays and various in vivo animal models under hypoxia. Based on results of this study, cytopiloyne will be a prospective herb angiogenesis inhibitor candidate to control animal or human cancer formation as adjuvant therapy. Abstract: Anti-angiogenesis is a pivotal combination treatment approach in cancer therapy but rare using on companion animals. This study aimed at evaluating the anti-angiogenic effect of a B. pilosa sourced polyacetylenic glucoside, cytopiloyne, on various in vitro assays and in vivo models. We provide evidences showing that CP has anti-angiogenic activities. Firstly, CP inhibited sponge/ Matrigel plug angiogenesis from tumor cells and decreased the survival of tumor cells on hypoxic conditions. Besides, CP declined PKCα protein expression which a protein leads to the growth and spread of tumors under hypoxia. Secondly, inhibitory effects of CP on endothelial angiogenesis were confirmed by chick chorioallantoic membrane assay, tube formation of SVEC4-10 cells and Matrigel plug assay. A dose-dependent CP treatment inhibited 4T1 cells proliferation under hypoxia and migration. It also suppresses VEGF transcription under hypoxia. Finally, we found that CP decreased PDIA4, a novel regulator of cancer growth, expression in endothelial cells. This effect was confirmed by PDIA4 knockout mice with reduced angiogenesis in Matrigel plug assay. Taken together, these results suggest that CP might act as a promising anti-angiogenic herbal agent candidate to be used in animal hypervascularized cancer of veterinary medicine or in combination to control human cancer as adjuvant therapy.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

The perturbations of DNA methyltransferase 3 alpha (DNMT3A) may cause uncontrolled gene expression, resulting in cancers and tumors. The DNMT inhibitors Azacytidine (AZA) and Zebu-larine (ZEB) inhibit the DNMT family with no specificities and consequently would bring side effects during the treatment. Therefore, it is vital to understand their inhibitory mechanisms in DNMT3A to inform the new inhibitor design for DNMTs. Herein, we carried out molecular dynamics (MD) and quantum mechanics/molecular mechanics (QM/MM) simulations to investigate the inhibitory mechanisms of AZA and ZEB. The results were compared to the methyl transfer of cytosine. We showed AZA might stop the methyl transfer process, whereas the ZEB might be stuck in a me-thyl-transferred intermediate (IM3). Such IM3 state then fails the elimination due to the unique protein dynamics that result in missing the catalytic water chain. Our results brought atomic-level insights into the mechanisms of the two drugs in DNMT3A, which could benefit the new generation of drug design for the DNMTs.

This study aims to develop an in-situ field repair approach, special for aircraft composite structures, to enhance the interlaminar toughness of plain woven composites (PWCs) by adding multi-walled carbon nanotubes (MWCNTs). MWCNTs are dispersed at each interface between prepreg layers by means of solvent spraying with the density is 1.58 g/m2. And then, the layers are stacked with the predefined sequence and cured at 120℃ and 1 bar pressure using the heat repairing instrument. Moreover, double cantilever beam (DCB) standard test is used to investigate the interlaminar toughening effect due to the MWCNTs. For comparison, original samples are also prepared, the results indicate that the introduction of MWCNTs can favorably enhance the interlaminar toughness of PWCs at field repair approach and the Mode I fracture energy release rate GIC increases by 102.92%. Based on finite element method (FEM) of continuum damage mechanics, the original and MWCNTs toughening specimen under DCB Mode I fracture are modeled and analyzed. The simulation and experiment are in good agreement. Finally, the toughening mechanism of MWCNTs is explored by scanning electron microscope (SEM), it is founded that a large amount of Fiber-matrix (F-M) interface debonding and matrix cracking of mountain shape are the major modes of fracture accompanied with few fiber breakage and matrix peeling off for the MWCNTs toughening specimens.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

COVID-19 is a highly infectious respiratory illness caused by SARS-CoV-2, and acute lung injury (ALI) is the major cause of COVID-19. The challenge in studying SARS-CoV-2 pathogenicity is the limited availability of animal models. Therefore, it is necessary to establish animal models that can reproduce multiple characteristics of ALI to study therapeutic applications. The present study established a mouse model that has features of ALI that are similar to COVID-19 syndrome to investigate the role of ACE2 and the administration of the Chinese herbal prescription NRICM101 in ALI. Mice with genetic modifications, including overexpression of human ACE2 (K18-hACE2 TG) and absence of ACE2 (mACE2 KO), were intratracheally instillated with hydrochloric acid. The acid intratracheal instillation induced severe immune cell infiltration, cytokine storms, and pulmonary disease in mice. Compared with K18-hACE2 TG mice, mACE2 KO mice exhibited dramatically increased levels of multiple inflammatory cytokines (IL-6, TNF-α, and TGF-β1) in bronchoalveolar lavage fluid, histological evidence of lung injury, and dysregulation of MAPK and MMP activation. In mACE2 KO mice, NRICM101 could ameliorate the disease progression of acid-induced ALI. In conclusion, the established mouse model provided an effective platform for researchers to investigate pathological mechanisms and develop therapeutic strategies for ALI, including COVID-19-related ALI.

Studies on the neurobiological causes of anxiety disorders suggest that the GABA system in-creases synaptic concentration and enhances the affinity of GABAA (type A) receptors for ben-zo-diazepine ligands. Flumazenil antagonizes the benzodiazepine binding site of the GABA (γ-aminobutyric acid) type /benzodiazepine receptor (BZR) complex in the central nervous sys-tem (CNS). The integration of the metabolites of flumazenil by LC-tandem mass spectrometry will complete understanding of the in vivo metabolism of flumazenil and accelerate radio-pharmaceutical inspection and registration. The main goal of our study was to investigate using reversed-phase HPLC (PR-HPLC) coupled with electrospray ionization triple quadrupole tan-dem mass spectrometry (ESI-QqQ MS) for the identification of flumazenil and its metabolites in a hepatic matrix. And a carrier-free nucleophilic fluorination with automatic synthesizer for [18F]flumazenil which applied to in vivo nano-positron emission tomography (Nano-PET)/computed tomography (CT) imaging and ex vivo bio-distribution used to analyze in normal rats. The study showed that 50% of the flumazenil was bio-transformed at 60 min by the rat liver homogenate, while one metabolite (M1) was a methyl transesterification product of flumazenil. In a rat liver microsomes system, two metabolites were identified (M2 and M3) as its carboxylic acid and hydroxylated ethylester forms, respectively. [18F]flumazenil in vivo nanoPET/CT imag-ing and ex vivo bio-distribution assay also showed significant effects on GABAA receptor availa-bility in the amygdala, prefrontal cortex, cortex, and hippocampus in the rat brain, worriless about the formation of metabolites. We showed completion of the bio-transformed course of flumazenil by the hepatic system; and [18F]flumazenil can be a good ligand and serve as a PET agent for determination of GABAA/BZR complex for multiplex neurological syndromes in the clinical stage.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

Breast cancer is a complex and heterogeneous disease that displays diverse molecular subtypes and clinical outcomes. Although it is known that the location of tumors can affect their biological behavior, the underlying mechanisms are not fully understood. In our previous study, we found a differential methylation profile and membrane potential between left (L) and right (R)-sided breast tumors. In this current study, we aimed to identify the ion channels responsible for this phenomenon and determine any associated phenotypic features. To achieve this, experiments were conducted in mammary tumors in mice, human patient samples, and with data from public datasets. The results revealed that L-sided tumors have a more depolarized state than R-ones. We identified a 6-ion channel-gene signature (CACNA1C, CACNA2D2, CACNB2, KCNJ11, SCN3A, and SCN3B) associated with side: L-tumors exhibit lower expression levels than R-ones. Additionally, in silico analyses show that the signature correlates inversely with DNA methylation writers and with key biological processes involved in cancer progression, such as proliferation and stemness. The signature also correlates inversely with patients’ survival rates. In an in vivo mouse model, we confirmed that KI67 and CD44 markers were increased in L-sided tumors and similar tendency for KI67 was found in patient L-tumors. Overall, this study provides new insights into the potential impact of anatomical location on breast cancer biology and highlights the need for further investigation into possible differential treatment options.

The performance of recycled aggregate concrete deteriorates due to the defects of adhesive mortar, pores and cracks on the surface of recycled aggregate. It is of great engineering significance to modify the reclaimed aggregate to improve its performance and adaptability. In this paper, the physical and chemical properties of waste concrete recycled aggregate are reviewed. Then, the existing modification methods and technologies of recycled aggregate, including physical, chemical and biological methods, are reviewed. Finally, the existing problems of the current modification technology are summarized, and the future research direction is proposed. It is expected to provide a new idea and method for the modification of waste concrete recycled aggregate.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

The MLL gene is a site of frequent rearrangement in acute leukemia with multiple fusion partners, but MLL-SEPT6 rearrangement is rare in clinical leukemia practice, and only 13 cases have been reported. We describe the case of an acute myelogenous leukemia child with MLL-SEPT6 rearrangement whose age of onset and accompanying gene mutations differs from previous reports. Considering the poor prognosis of leukemia children with MLL-SEPT6 rearrangement and the unsatisfactory results of existing treatments, the study of this case may provide new theories for diagnosis and treatment of MLL-SEPT6-associated childhood acute leukemia.

The objective of this study was to synthesize 9-/13-position substituted berberine derivatives and evaluated their cytotoxic and photocytotoxic effects against three human cancer cell lines. Among all the synthesized compounds, 9-O-dodecyl- (5e), 13-dodecyl- (6e) and 13-O-dodecyl-berberine (7e) exhibited stronger growth inhibition against three human cancer cell lines, (HepG2, HT-29 and BFTC905), in compare with structurally related berberine (1). These three compounds also showed the photocytotoxicity in human cancer cells in a concentration-dependent and light dose-dependent manner. Through flow cytometry analysis, we found out a lipophilic group at 9-/13-position of berberine may have facilitated its penetration into test cell and hence enhanced its photocytotoxicity on human liver cancer cell HepG2. Further, in cell cycle analysis, 5e, 6e and 7e induced HepG2 cells to arrest at S phase and caused apoptosis upon irradiation. In addition, photodynamic treatment of berberine (1) and its derivatives 5e, 6e and 7e again showed a significant photocytotoxic effects on HepG2 cells, induced remarkable cell apoptosis, greatly increased intracellular ROS level and the loss of mitochondrial membrane potential. These results over and again confirmed that berberine derivatives 5e, 6e and 7e greatly enhanced photocytotoxicity. Taking together, the test data led us to conclude that berberine derivatives with a dodecyl group at 9-/13-position could be great candidates for the anti-liver cancer medicines developments.

Infectious keratitis (IK) represents a major cause of corneal blindness. This study aims to investigate the demographics, risk factors, microbiological characteristics and antibiotic susceptibility patterns of IK in Taiwan over the past 15 years. A retrospective population-based study was conducted using the Chang Gung Research Database. Patients with IK were identified by diagnostic codes for corneal ulcer from 2004 to 2019. Of 7807 included subjects, 45.2% of patients had positive corneal cultures. The proportion of contact lens-related IK declined, while that of IK related to systemic diseases grew. The percentage of isolated gram-positive bacteria surpassed that of gram-negative bacteria in the 15-year period. The prevalence of Pseudomonas aeruginosa showed a decreasing trend (p = 0.004), whereas coagulase-negative Staphylococcus (CNS) and Propionibacterium species were increasingly detected (p &lt; 0.001). Overall, the trend of antibiotic susceptibility of both gram-positive and gram-negative bacteria did not change throughout the study period. The susceptibility to the test antibiotics maintained over 90% in gram-negative isolates during 15 years. Vancomycin preserved 100% susceptibility to all gram-positive isolates. Since most tested antibiotics exhibited stable susceptibility over decades, this study reinforced that fluoroquinolones and fortified vancomycin continue to be good empiric therapies for treating bacterial keratitis in Taiwan.

In order to make full use of the complementarity of existing navigation systems to improve the navigation and positioning accuracy, this paper investigates the visual/INS integrated navigation system based on the factor graph optimization (FGO) algorithm. In the traditional visual/INS integrated navigation system, there is often the problem of image blurring due to the rapid change of light and shadow captured by the vision sensor and the attitude change of the carrier, which leads to the decrease of the positioning accuracy of the combined navigation system. Therefore, this paper firstly introduces Retinex algorithm and BID algorithm to carry out the design of image de-blurring method; then implements the visual/INS integrated navigation algorithm based on the factor graph optimization method; finally, the experimental scheme is designed, comparative experiments are carried out, and the researched method is verified by using the public dataset. The experimental results show that the combined navigation algorithm realized in this paper has high accuracy, and its positioning accuracy is improved by 40% compared with visual positioning.

The concept and policies of multiple early cancer detection (MCED) have gained significant attention from governments worldwide in recent years. In the era of burgeoning artificial intelligence (AI) technology, the integration of MCED with AI has become a prevailing trend, giving rise to a plethora of MCED AI products. However, due to the heterogeneity of both the detection targets and the AI technologies, the overall diversity of MCED AI products remains considerable. The types of detection targets encompass protein biomarkers, cell-free DNA, or combinations of these biomarkers. In the development of AI models, different model training approaches are employed, including datasets of case-control researches or real-world cancer screening datasets. Various validation techniques, such as cross-validation, location-wise validation, and time-wise validation are used. All of the factors show significant impacts on the predictive efficacy of MCED AIs. After the completion of AI model development, deploying the MCED AIs in clinical practice presents numerous challenges, including presenting the predictive reports, identifying the potential locations and types of tumor, and addressing cancer-related information such as clinical follow-up and treatment. This study reviews several mature MCED AI products currently available in the market, detecting their composing factors from serum biomarkers detection, MCED AIs training/validation, and the clinical application. The review illuminates the challenges encountered by existing MCED AI products across these stages, offering insights into the continued development and obstacles within the field of MCED AI.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

This study compared growth performance, serum biochemical indicators, rumen fermentation parameters, rumen bacterial structure, and fecal bacterial structure of cattle and yaks, fed for two months, given a feed containing concentrate to roughage ratio of 7: 3 on dry matter basis. Compared with cattle, yak showed better growth performance. The serum biochemical results showed that the albumin: globulin ratio in yaks serum was significantly higher than that in cattle. Aspartate aminotransferase, indirect bilirubin, creatine kinase, lactate dehydrogenase and total cholesterol were significantly lower in yaks than that in cattle. Rumen pH, acetate to propionate ratio, and acetate were lower in yaks than in cattle while the lactate in yaks was higher than in cattle. There were significant differences in the structure of ruminal as well as fecal bacteria between cattle and yaks. The prediction of rumen bacterial function showed that there was metabolic difference between cattle and yaks. In general, the metabolic pathway of cattle was mainly riched in de novo synthesis of nucleotides, while that of yaks was mainly riched in the metabolic utilization of nutrients. This study provides a basis for understanding the rumen ecology under the condition of high concentrate diet.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

The lengthy maturation period is the key cause of the reduced hot pepper market value. An experiment was performed to assess the effects of R/B/W light qualities on reducing the maturation period. The maturation period was shortened by 16 days under 4R:1B:5W compared to the control. The appearance of the first flower is a limiting factor affecting the maturation period. It exhibited a dark purple color and an abnormal petal under 4R:1B:5W compared to the control, which was associated with increased contents of flavonoids, total organic acids, and phenolics and decreased total amino acid and carbohydrate contents. Plant hormone, flavonoid, ABC transporters, key metabolites (such as amino acid, carbohydrate, organic acid) was associated with first flower development. Ethylene response factors (ERFs) mediated by light, especially ERF021, were identified as potential hub regulators during the development of the first flower due to their involvement in all the associated metabolic pathways.

In this paper, the effects of different food-grade enzymes on the antigenicity of casein (CN), β- lactoglobulin (β-LG) and ɑ-lactalbumin (ɑ-LA) in natural cow milk were studied. The degree of hydrolysis (DH), SDS-PAGE and molecular mas (MW) distribution of cow milk (CM) hydrolysates was assessed. Additionally, the residual antigenicity of CM hydrolysates was evaluated by using ELISA and western blotting with anti-CN, anti-β-LG and anti-ɑ-LA rabbit polyclonal antibody. The results showed that Alcalase and Protamex hydrolysis could efficiently reduce the antigenicity of CN, β-LG, ɑ-LA, showed a higher DH and the loss of density of CM proteins, as indicated by SDS-PAGE. The increasing of the low MW (<3 kDa) in CM hydrolysates was also presented. It was also found that Protamex, Alcalase could be more efficiently hydrolyzed major allergenic of CM than other enzymes for the development of hypoallergenic cow milk. Our research will lay a theoretical foundation for the study of hypoallergenic cow milk.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

We theoretically investigate and optimize four-wave mixing (FWM) in silicon nitride (SiN) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. Based on extensive previous measurements of the material parameters of the GO films, we perform detailed analysis for the influence of device parameters including waveguide geometry, GO film thickness, length, and coating position on the FWM conversion efficiency (CE) and conversion bandwidth (CB). The influence of dispersion and photo-thermal changes in the GO films is also discussed. Owing to the strong mode overlap between the SiN waveguides and the highly nonlinear GO films, FWM in the hybrid waveguides can be significantly enhanced. We obtain good agreement with previous experimental results and show that by optimizing the device parameters to balance the trade-off between Kerr nonlinearity and loss, the FWM CE can be improved by as much as ~20.7 dB and the FWM CB can be increased by ~4.4 folds, relative to the uncoated waveguides. These results highlight the significantly enhanced FWM performance that can be achieved in SiN waveguides by integrating 2D layered GO films.

Researches on flexible thermoelectric (TE) materials usually focus on conducting polymers (CPs) and CP-based composites; however, it is a great challenge to obtain high TE properties comparable to inorganic counterparts. Here, we report an n-type Ag₂Se film on flexible nylon membrane with an ultrahigh power factor ~987.4 ± 104.1 μWm⁻¹K⁻² at 300 K and an excellent flexibility (93% of the original electrical conductivity retention after 1000 bending cycles around a 8-mm diameter rod). The flexibility is attributed to a synergetic effect of the nylon membrane and the Ag₂Se film intertwined with numerous high-aspect-ratio Ag₂Se grains. A TE prototype composed of 4-leg of the hybrid film generates a voltage and a maximum power of 19 mV and 460 nW, respectively, at a temperature difference of 30 K. This work opens opportunities of searching for high performance TE film for flexible TE devices.

Taiwan’s Chi Mei Medical Center has a vision of becoming a sustainable organization. They found they violated the sustainable development goal (SDG) 13 (“Climate Action”) since its workflows consume excessive tangible resources and waste much operation time. To fulfill the vision, the Chi Mei Medical Center first introduced electronic invoicing. Implementing this electronic invoicing included adopting cloud E-invoice data and creating a software robot for auditing them. This study presents this software robot and its contributions. The software robot replaces an internal auditor to log into Taiwan’s E-invoice platform, download cloud E-invoice data, and detect the inconsistency between these cloud and on-premise data. Internal auditors of the Chi Mei Medical Center only needed to confirm the detection results. They welcome this software robot since it significantly reduces their work burdens. They approved more software robots for assisting other workflows. Besides, the Chi Mei Medical Center earned profits after eliminating paper invoices. This elimination helped release less carbon. This study concludes that chasing a sustainable organization is unnecessarily equivalent to the requirement of more costs. A software robot represents the last puzzle for constructing a paperless workflow since it can resolve the resistance of existing workers to a new workflow.

The parameter estimation problem for polynomial phase signals (PPSs) arises in a number of fields, including radar, sonar, biology, etc. In this paper, a fast algorithm of parameter estimation for monocomponent PPS is considered. We propose the so-called LSU-EKF estimator, which combines the least squares unwrapping (LSU) estimator and the extended Kalman filter (EKF). First, the coarse estimates of the parameters of PPS are obtained by the LSU estimator using a small number of samples. Subsequently, these coarse estimates are used to initial the EKF. Monte-Carlo simulations show that the computation complexity of the LSU-EKF estimator is much less than that of the LSU estimator, with little performance loss. Similar to the LSU estimator, the proposed algorithm is able to work over the entire identifiable region. Moreover, in the EKF stage, the accurate estimated results can be output point-by-point, which is useful in real applications.

Non-union is one of the severe complications of traumatic fracture and still no standard therapeutic recommendations currently. A total of eleven patients were treated on the lesions for non-union, after the failure of open reduction internal fixation (ORIF) or total hip replacement, by autologous conditioned serum (ACS) for one to three times monthly and followed up. Seven patients received ACS three times, three patients received it two times, and the only one who underwent total hip replacement received it once. Ten patients achieved union at the last follow-up visit, indicating the effectiveness of ACS on patients who suffered from non-union after ORIF. ACS has the potential as an alternative or adjective treatment for non-union and is worthy to be investigated further for the benefits of patients.