It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

Dissolved organic matter (DOM) derived from organic fertilizers may increase soil phosphorus (P) availability. However, the frequently observed correlation between soil P availability and dissolved organic carbon (DOC) content has led to an excessive focus on DOC content at the expense of DOM properties. The present study investigated the influence of DOM characteristics on soil P availability by using a 6-year field experiment and microcosms of P sorption in paddy soil. Our results showed that partial replacement of chemical P fertilizer with manure or crop straw increased P fertilizer-use efficiency, even when decreasing chemical P input by 34 %, compared to normal chemical fertilization. The microcosm experiment demonstrated that DOM properties, rather than total DOC content, determine soil P sorption capacity, despite the significant correlation between DOC content and P availability observed in the field experiment. Manure-DOM exerted stronger inhibitory effects on P sorption than straw-DOM, and high molecular weight (HMW)-fractionated DOM exerted stronger inhibitory effects on P sorption than low-molecular-weight-fractionated DOM by 16-20%. The mechanism was rooted in the HMW DOM with unique characteristics (e.g., strong aromaticity, hydrophobicity, abundant humic-like components, carboxyl groups, and benzene ring structures) competing for soil P sorption sites (e.g., reduction in specific surface area and micropore volume), decreasing the soil surface charge (e.g., zeta potential), and thereby suppressing P sorption in paddy soil. Our study points out a promising avenue for regulating organic matter properties with organic fertilization to improve P use efficiency in agricultural soils.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

In order to explore the effect of fertilization patterns on the growth of rapeseed seedlings under waterlogging stress, three fertilization patterns (conventional fertilization, supplemental organic fertilization, and supplemental microbial fertilization) were set up using the variety Xiangyou 708 as the material, and waterlogging treatment was carried out during the seedling stage of rapeseed. The effects of fertilization patterns on the growth of rapeseed seedlings and rhizosphere microorganisms under waterlogging stress were investigated. The results showed that all three fertilization patterns exhibited that waterlogging stress inhibited the growth of rapeseed seedlings, inhibited root activity, and changed the structure of rhizosphere bacterial colonies. However, supplemental organic fertilization and microbial fertilization could better promote the growth of rapeseed seedlings, reduce the impact of waterlogging stress on the growth of rapeseed seedlings, and accelerate the recovery of rapeseed seedlings after waterlogging stress. In addition, supplemental microbial fertilization could also change the structure of rhizosphere bacterial colonies. Under normal water supply, supplemental organic fertilization enriched P_Bacteroidota, P_Actinobacteriota, P_Chloroflexi, and G_Flavisolibacter in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Bacteroidota and G_Flavisolibacter in the rhizosphere soil of rapeseed. After 7 days of waterlogging treatment, supplemental organic fertilization enriched P_Verrucomicrobiota in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Actinobacteriota, G_SC-I-84, and G_Ellin6067 in the rhizosphere soil of rapeseed. The enrichment of these bacteria may be related to the growth promotion and waterlogging tolerance of rapeseed. This study provides evidence that microbial fertilizer and organic fertilizer can promote the growth of rapeseed and enhance its waterlogging tolerance, as well as evidence that some rhizosphere microorganisms have a potential role in promoting the growth and waterlogging tolerance of rapeseed.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

Many agricultural water uses crowd the river ecology of the river water, thus leading to irreversible habitat damage. This paper presents an agricultural economic loss calculation model that is based on river ecological basic flow (REBF) protection by introducing a typical crop water requirement coefficient. First, the water balance equation is used according to a set of REBF protection values to compute the agricultural water shortage that results in the REBF. Second, the agricultural water shortage that results in REBF protection and a typical crop water requirement coefficient are used to determine the food production generated by REBF protection. Finally, the loss of food production and the food market prices are used to determine the agricultural economic loss caused by the different protection levels of REBF. A case study of the Weihe River in China is conducted. The calculation model is used to compute the agricultural economic loss on the basis of REBF protection in the Baoji section of the Weihe River, and the change law of the agricultural economic loss that results in different levels of the REBF is discussed. In addition, changes in the canal water use coefficient and the crop structure that affect agricultural economic loss are analyzed. Results show that the spatial and temporal variations in the runoff affect the changes in time and space of the agricultural economic loss. The higher the REBF protection level, the higher the agricultural economic loss. In addition, agricultural economic loss can provide a quantitative basis for reasonable REBF protection. The size of agricultural economic loss helps the government sector in decision-making on REBF protection.

A large amount of accurate river cross-section data is indispensable for predicting river stages. However, the measured river cross-section data are usually sparse in the transverse direction at each cross-section as well as in the longitudinal direction along the river channel. This study presents three algorithms to resample the river cross-section data points in both the transverse and longitudinal directions from the original data. The resampled cross-section data based on the linear interpolation satisfactorily maintains the topographic and morphological features of the river channel, especially in the meandering river segment. A two-dimensional (2D) high-resolution unstructured-grid hydrodynamic model was used to assess the performance of the original and resampled cross-section data on a simulated river stage under low flow and high flow conditions. The simulated river stages are significantly improved using the resampled cross-section data based on the linear interpolation in the tidal river and non-tidal river segments. Furthermore, the performance of the 2D and three-dimensional (3D) models on the simulated river stage was also evaluated using the resampled cross-section data. The results indicate that the 2D and 3D models reproduce similar river stages in both tidal and non-tidal river segments under the low flow condition. However, the 2D model overestimates the river stages in both the tidal and non-tidal river segments compared to the 3D model under the high flow condition. The model sensitivity was implemented to investigate the influence of bottom drag coefficient and vertical eddy viscosity on river stage. The results reveal that bottom drag coefficient has a minor impact on river stage, but the vertical eddy viscosity is insensitive to river stage.

Marek’s disease (MD) is an important neoplastic disease caused by serotype 1 Marek's disease virus (MDV-1), which results in severe economic losses worldwide. Despite vaccination practices that have controlled the MD epidemic, current increasing MD-suspected cases indicate the persistent viral infections circulating among vaccinated chicken farms in many countries. However, the lack of available information about phylogeny and molecular characterization of circulating MDV-1 field strains in Taiwan reveals a potential risk in MD outbreaks. This study investigated the genetic characteristics of 18 MDV-1 isolates obtained from 17 vaccinated chicken flocks in Taiwan between 2018 and 2020. Based on the sequences of the meq oncogene, phylogenetic analysis demonstrated that the circulating Taiwanese MDV-1 field strains were predominantly in a single cluster that showed high similarity with strains/isolates from countries of East Asian region. Because the isolated strains were obtained from CVI988/Rispens vaccinated chicken flocks and the molecular characteristics of the Meq oncoprotein showed the features like vvMDV and vv+MDV strains, the circulating Taiwanese MDV-1 field strains may have higher virulence compared with vvMDV pathotype. In conclusion, the presented data demonstrate the circulation of hypervirulent MDV-1 strains in Taiwan and highlight the importance of routine surveillance and precaution strategies in response to the emergence of enhanced virulent MDV-1.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

Landslide is one of the most common geological disasters in China, which is characterized by suddenness and uncertainty, and it is difficult to realize accurate identification, early warning and forecasting of landslide disaster by conventional means. With the development of high-resolution remote sensing satellites and InSAR surface deformation monitoring technology, the traditional means of landslide monitoring data sources are limited, and there is a lack of effective methods to excavate the characteristics of the spatial distribution of landslide hazards and their triggering factors and other issues. In this paper, the area extending 10 km outside the VII isobar of the Gengma earthquake is taken as the study area, and 13 evaluation factors are screened out by integrating the factors of InSAR surface deformation, topography and geological environment, and the Bayesian Optimized Convolutional Neural Network (BO-CNN) is used for the evaluation of landslide susceptibility, and the BO-RF and PSO-SVM models are selected for the comparative analysis. The model accuracy evaluation was carried out by three indexes: ROC curve, AUC value and FR value, in which the ROC curves of PSO-SVM, BO-RF and BO-CNN were all close to the upper-left corner of the corner, and the AUC values were 0.9388, 0.9529, and 0.9535, respectively, and the FR value of landslide in the high susceptibility area of BO-CNN was as high as 14.9, and was higher than that of PSO-SVM and BO-RF, respectively. SVM and BO-RF model is 4.55 and 3.69 higher, the experimental results show that the BO-CNN model used in this paper has a better effect in landslide susceptibility evaluation, and the research results of the local government's disaster prevention and mitigation measures are of great significance.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The prediction of drug--target interactions is always a key task in the field of drug redirection. However, traditional methods of predicting drug--target interactions are either mediocre or rely heavily on data stacking. In this work, we merged heterogeneous graph information and obtained effective node information and substructure information based on mutual information in graph embeddings. We then learned high quality representations for downstream tasks, and proposed an end--to--end auto--encoder model to complete the task of link prediction. Experimental results show that our method outperforms several state--of--art models. The model can achieve the area under the receiver operating characteristics (AUROC) curve of 0.959 and area under the precise recall curve (AUPR) of 0.848. We found that the mutual information between the substructure and graph--level representations contributes most to the mutual information index in a relatively sparse network. And the mutual information between the node--level and graph--level representations contributes most in a relatively dense network.

A field experiment was conducted in Ninghe, Tianjin, China, using 15N isotope method to evaluate the application of organic fertilizer on N distribution patterns of labelled and unlabeled N fertilizer, ammonium sulfate -15N uptake by rice, N use efficiency (NUE), and the fate of (15NH4)2SO4 applied. The experiment included eight treatments: CK-N (control + no-duck), CK-D (control + ducks), CF-N (chemical fertilizer + no-ducks), CF-D (chemical fertilizer + ducks), CM-N (chemical fertilizer + organic fertilizer + no-ducks), CM-D (chemical fertilizer + organic fertilizer + ducks), CD-N (chemical fertilizer 30% off + organic fertilizer + no-ducks), and CD-D (chemical fertilizer 30% off + organic fertilizer + ducks). The results showed that the application of organic fertilizer whether CM or CD significantly increased N and P concentrations over control (CK) and chemical fertilizer (CF). Moreover, no-significant differences were found in 15N fresh grain and husk concentration. Both organs ranged of 14.2-14.4 g kg-1 and 6.2-6.3 g kg-1, respectively. N derived from the fertilizer and soil significantly affected fresh grain compared to fresh husk. However, N uptake and N use efficiency did not show any differences. We concluded that organic fertilizer has a significant influence on rice growth and promote crop productivity.

During the smelting process of AOD furnace, the unbalanced reaction of material will lead to the occurrence of splashing. It will not only damage the smelting equipment, but also seriously injure the personnel. In this study, first, the information of liquid level, audio information, and vibration information are detected by multiple sensors respectively. Then, the fused information is used to forecast the splashing. Finally, the multitasking fuzzy controller is used to suppress splashing. The results show that the method of forecasting and suppressing splashing can accurately forecast and achieve rapid suppression. Thus, the efficiency of smelting can be improved.

This study aims to develop an in-situ field repair approach, special for aircraft composite structures, to enhance the interlaminar toughness of plain woven composites (PWCs) by adding multi-walled carbon nanotubes (MWCNTs). MWCNTs are dispersed at each interface between prepreg layers by means of solvent spraying with the density is 1.58 g/m2. And then, the layers are stacked with the predefined sequence and cured at 120℃ and 1 bar pressure using the heat repairing instrument. Moreover, double cantilever beam (DCB) standard test is used to investigate the interlaminar toughening effect due to the MWCNTs. For comparison, original samples are also prepared, the results indicate that the introduction of MWCNTs can favorably enhance the interlaminar toughness of PWCs at field repair approach and the Mode I fracture energy release rate GIC increases by 102.92%. Based on finite element method (FEM) of continuum damage mechanics, the original and MWCNTs toughening specimen under DCB Mode I fracture are modeled and analyzed. The simulation and experiment are in good agreement. Finally, the toughening mechanism of MWCNTs is explored by scanning electron microscope (SEM), it is founded that a large amount of Fiber-matrix (F-M) interface debonding and matrix cracking of mountain shape are the major modes of fracture accompanied with few fiber breakage and matrix peeling off for the MWCNTs toughening specimens.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

Since the development of CBCT had been utilized in dentistry, the images of the CBCT can assist the surgeon to evaluate the anatomy carefully. Despite the value of the radiology evaluation, the implant procedures may require additional consideration rather than only evaluating the anatomical factors. The purpose of this study is to evaluate the predictability of using CBCT alone to plan for implant placement on the edentulous patient digitally CBCT images were analyzed by clinicians, measuring the ridge heights and widths of 4 selected implant sites in the maxillary and 2 selected implant sites in the mandibular arches for 91 patients planning for the implant-supported overdenture. (A total of 47 patients out of the 91 had completed the implant placement on the edentulous ridge, contributing to 55 upper and/or lower arches (136 dental implants). . Both predictabilities are low, implying the CBCT planning for implant placement on the edentulous ridge is not a good index and is insufficient to predict the surgical procedures as a solo method. The finding of this study indicates that digital planning by CBCT is insufficient to serve as an individual tool to predict implant procedures. Further information and evaluation must be considered for implant placement on the edentulous ridge.

In this study, seventeen faceted gem-quality chrysoberyls exhibiting an attractive canary yellow color were investigated by a series of gemological, spectral, and chemical methods. Microscopic observation reveals distinct growth lines and inclusions, including CO2 fluids, carbon, and mineral crystals such as calcite, quartz, sillimanite, and mica, identified by the Raman spectrum. The FTIR spectrum exhibits the 2405 and 2160 cm-1 feature peaks and a 3223 cm-1 peak in all samples, which can be accompanied by the 3112 cm-1 shoulder, 3301, and 3412 and 3432 cm-1 peaks. The UV-Vis spectrum shows a Fe-related peak at 440 nm, along with the 650–660 nm band and the absorption band in the blue zone of the visible light. The chemical results of EDXRF reveal a V-poor, Cr-poor, and Fe-rich feature. The spectral and chemical results could contribute to explaining the origin of the canary yellow color, which originates from the abundant amount of Fe with very little influence from Cr or V.

The aim of this case-series report article is to provide a new topical view of the styletubation (video intubating stylet technique) in obese patients undergoing bariatric surgeries. In contrast to various conventional direct laryngoscopes (DLs), videolaryngoscopes (VLs) have been applied in such obese population with potentially difficult airway populations. The safety and effectiveness of VLs have been repeatedly studied and the superiority of VLs then has been observed and is advocated as a routine use. In this article, among our vast use experiences of the styletubation (more than 54,998 patients since 2016) for routine tracheal intubation, we present such unique experience to apply such intubating technique in obese patient undergoing bariatric surgery. Consistent with the experiences applied in other patient populations, we found the styletubation technique to be swift (the time to intubate from 5 s to 24 s), smooth (first-attempt success rate: 100%), safe (no airway complications), and easy (high subjective satisfaction). The learning curve can be steep but is easily overcome if technical pitfalls are avoided. We, therefore, propose that the styletubation technique can be feasibly applied for tracheal intubation in obese patients undergoing bariatric surgery.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Flavin-dependent monooxygenases (FMOs) have made substantial influence as catalysts for monooxygenation reactions, impacting diverse field such as drug metabolism, environmental studies, and natural product synthesis. Their application in biocatalysis boasts several advantages over conventional chemical catalysis, such as heightened selectivity, safety, sustainability, and eco-friendliness. In the realm of biomedicine, FMOs are pivotal in antibiotic research, modulating natural products, antimicrobial agents, and pathways involved in drug synthesis. They're also underscored as potential pharmaceutical targets, pivotal in disease progression and viable for therapeutic intervention. Additionally, FMOs play a substantial role in environmental science, especially in pesticide processing and plant vitality. Their involvement in biosynthesizing compounds like polyethers, tropolones, and ω-hydroxy fatty acids, with remarkable regio- and stereoselectivity, renders them indispensable in drug discovery and development. As our comprehension of FMOs' catalytic mechanisms and structures advances, coupled with cutting-edge biotechnologies like computational design and directed evolution, FMOs are poised to occupy an increasingly significant role in both scientific exploration and industrial applications.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

The Urban heat island (UHI) effect has evolved into one of the key environmental problems affecting urban ecological environment and sustainable development. Based on 52 Urban Thermal Heat spots (UTHSs) with significant differences between land use structure and UGI spatial layout within the influence range of UHI in Shanghai, Landsat-8/9 satellite images were used to construct a high-dimensional data set reflecting the impact of built environment components on urban thermal environment. Descriptive statistical analysis was used to analyze the spatial difference qualitatively. Using stepwise regression model and partial least square regression (PLSR) model, the complex response relationship between UGI pattern differentiation and urban thermal environment in three spatial stratification ranges of UTHSs was quantitatively analyzed. Overall, the statistical explanatory power of the partial least square regression PLSR model is due to the stepwise regression model. The PLSR model points out that moderately increasing the average building height, CA, PLAND, LSI and LPI play a positive role in inhibiting/slowing down the growth of LST (land surface temperature), and the cooling effect of index weights decreases in order. However, the interaction effects of CA×Cohesion×AI×LPI and PLAND×CA×Cohesion×AI×LPI exert relatively small weight on the cooling effect, and according to the results, suggestions such as UGI structure and urban construction layout optimization can effectively alleviate the urban heat island effect are proposed.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

The present study investigated the insulin-like growth factors (IGFs) and their receptors and binding proteins among different pig breeds during weaning. Sixty Duroc (DR), Taoyuan black (TB), and Xiangcun black (XB) piglets (20 piglets per breed) were selected at 21 and 24 days of age (three days of post-weaning) to analyze organ indices, plasma concentrations of IGF and IGF-binding proteins (IGFBPs) using ELISA kits, and gene expression of IGF system-related components in different tissues. The plasma IGFBP-3 level in TB piglets was higher (P > 0.05) than in the XB and DR piglets at 21 days of age. At 21 days of age, compared with the DR piglets, the IGF-1 expression was lower (P < 0.05) in the kidney but was higher (P < 0.05) in the spleen of XB and TB piglets. At 24 days of age, the IGF-1 expression was higher (P < 0.05) in the kidney of TB piglets than in the XB and DR piglets, while IGFBP-3 in the stomach and IGFBP-4 in the liver of XB and TB piglets were lower (P < 0.05) compared with the DR piglets. Weaning down-regulated (P < 0.05) the IGF-1 expression in the jejunum, spleen, and liver of piglets, while up-regulated (P < 0.05) IGFBP-3 expression in the stomach, IGFBP-4 in the liver, IGFBP-5 in the ileum, and IGFBP-6 in the jejunum of DR piglets. Spearman’s correlation analysis showed a negative correlation (P < 0.05) between plasma IGFBP-2 and IGFBP-5 and the organ index of piglets. Collectively, there were significant differences in IGF system components among different pig breeds. The IGF system components were altered during weaning, which might be involved in weaning stress to decrease the growth of piglets.

In order to maintain the best conditions of the building from the first day of opening, explorations of office buildings in the world investigated the approaches of optimizing the building operation and property facilities, whereas building managers often have trouble prioritizing improvements toward their sustainable objectives. The challenge is due to numerous equipment types in the building, which has various durability in years and represents users’ different feelings of importance and satisfaction. When faced with multiple improvement projects, building managers are often unable to determine the order of implementation.Hence, this research applies the Analytic Hierarchy Process (AHP) using TAIPEI 101 Tower as a case study to explore the key factors affecting tenants’ willingness to lease office buildings by distributing questionnaires to real estate experts. By filtering out key indicators related to property facilities that users care about, this study used Importance and Satisfaction Analysis (IS Analysis) to identify items that need urgent improvement. The research revealed that air conditioning is the top priority for improvement through empirical evaluation and weight ranking. This study hopes to establish an evaluation model for facility improvements to help clarify the prioritization and defeat limited resources to projects effectively, which is helpful for sustainable property management.

Fracture grouting has been a widely used mitigation measure against seepage in the Yellow River Embankment. However, there is currently a lack of systematic investigation for evaluating the anti-seepage effectiveness of fracture grouting employed in this longest river embankment in China. Therefore, in this work, laboratory and in-situ experiments are carried out for investigating the reinforcement effect of fracture grouting in the Jinan Section of the Yellow River Embankment. In particular, firstly, the laboratory tests concentrate on studying the optimum strength improvement for cement-silicate grout by varying the content of backfilled fly ash and bentonite as admixtures. Flexural strength and Scanning Electron Microscope photographs are investigated for assessing the strength and compactness improvement. Subsequently, based on the obtained optimum admixtures content, in-situ grouting tests are carried out in the Jinan Section of the Yellow River Embankment to evaluate the anti-seepage effectiveness of fracture grouting, where geophysical prospecting and pit prospecting methods are employed. Laboratory results show that, compared with pure cement-silicate grouts, the gelation time of the improved slurry is longer and gelation time increases as fly ash content increases. The optimum mixing proportion of the compound cement-silicate grout is 70% cement, 25% fly ash and 5% bentonite, and the best volume ratio is 2 for the investigated cases. Geophysical prospecting using the Ground Penetrating Radar and High Density Resistivity methods can reflect the anti-seepage effectiveness of fracture grouting on site. It shows that the grouting material mainly flows along the axial direction of the embankment. The treatment that is used to generate directional fracture is proved to be effective. The injection hole interval distance is suggested to be 1.2 m, where the lapping effect of the grouting veins is relatively significant. For the investigated cases, the average thickness of the grouting veins is approximately 6.0 cm and the corresponding permeability coefficient is averagely 1.6 × 10⁻⁶ cm/s, which meets the anti-seepage criterion in practice.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Complex illumination condition is one of the most critical challenging problems for practical face recognition. In this paper, we propose a novel method to improve the illumination invariants for solving this challenge. Firstly, a new method based on the Lambert reflectance model is proposed to extract illumination invariant, which is less insensitive to complex illumination variations. Secondly, in order to repair the defects caused by process of illumination invariants extraction, Fast Mean Filter is utilized to smooth and remove noise. Lastly, for raising the richness of information in output image, a nonlinear normalization transformation is proposed. Compared with the state-of-the-arts, experimental results show that the proposed method can extract more robust illumination invariants. Apart from it, the richness of information in processed image is greater and superior performance in face recognition rate is superior.

Most of existing fuzzy forecasting models partition historical training time series into fuzzy time series and build fuzzy-trend logical relationship groups to generate forecasting rules. The determination process of intervals is complex and uncertainty. In this paper, we present a novel fuzzy forecasting model based on high-order fuzzy-fluctuation trends and the fuzzy-fluctuation logical relationships of the training time series. Firstly, we compare each data with the data of its previous day in historical training time series to generate a new fluctuation trend time series(FTTS). Then, fuzzify the FTTS into fuzzy-fluctuation time series(FFTS) according to the up, equal or down range and orientation of the fluctuations. Since the relationship between historical FFTS and the fluctuation trend of future is nonlinear, Particle Swarm Optimization (PSO) algorithm is employed to estimate the required parameters. Finally, use the acquired parameters to forecast the future fluctuations. In order to compare the performance of the proposed model with that of the other models, we apply the proposed method to forecast the Taiwan Stock Exchange Capitalization Weighted Stock Index (TAIEX) time series datasets. The experimental results and the comparison results show that the proposed method can be successfully applied in stock market forecasting or such kinds of time series. We also apply the proposed method to forecast Shanghai Stock Exchange Composite Index (SHSECI) to verify its effectiveness and universality.

This study examines the DCMA concerning the future risk of the water security status. We considered three risk factors: population growth, economic growth, and natural water supply demand differences. In the risk analysis part, we consulted with experts from several sectors including academia, Non-Governmental Organization (NGOs), and industry, to predict that the probability of future water stresses in high, medium, and low scenarios are 0.73, 0.24, and 0.03, respectively. In the decision analysis part, we adopted two Multiple Criteria Decision Analysis (MCDA) approaches that include Multiple Attribute Value Theory (MAVT) and Analytic Hierarchy Process (AHP) methods to evaluate the best alternative decision to alleviate future water stresses in the DCMA. The sensitivity analysis demonstrates the best option closely connects to the weighting scheme of the criteria considered in the framework. This study provides a valuable risk and decision analysis framework to analyze the water security status associated with the future water supply and demand gap decrease caused by three risk factors: population growth, climate change, and natural water supply.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Image segmentation is the process of partitioning an image into multiple segments where the goal is to simplify the representation of the image and make the image more meaningful and easier to analyze. In particular, semantic segmentation is an approach of detecting the classes of objects, based on each pixel. In the past, most semantic segmentation models were for only one single style, such as urban street views, medical images, or even Manga. In this paper, we proposed a semantic segmentation model called Dual-Pyramid Wide Residual Network (DPWRN) to solve the segmentation for cross-style datasets, which is suitable for diverse segmentation applications. The DPWRN integrated the Pyramid of Kernel paralleled with Dilation (PKD) and Multi-Feature Fusion (MFF) to improve the accuracy of segmentation. To evaluate the generalization of the DPWRN and its superiority over most state-of-the-art models, three datasets with completely different styles are tested in the experiments. Finally, the DPWRN verified its generalization and also showed its superiority over most state-of-the-art models.

Given the recent advances in information technology, speed has become an important requirement in data transmission. Given that an LED (light emitting diode) can turn on and off several thousand or even millions of times per second, then LiFi (light fidelity) technology has strong advantages over WiFi (wireless fidelity) in terms of speed. In this research project, a consortium involving an academic institution decided to evaluate the maturity of LiFi technology and design a demonstrator that could be integrated in a vehicle via an intra-vehicle data transmission system. The demonstrator is to implement a two-way LiFi communication between the reading light of a vehicle and a portable device such as a tablet or smartphone. The nomadic device must display, via an interface, data in real time. The data is RNT (Digital Terrestrial Radio) and TNT (Digital Terrestrial Television) provided by an in-house antenna. LiFi depends on optical technology. The optical characteristics have significant influences on the system. The paper shows ways to improve the system’s throughput, communication range, and reception area. By replacing the reading light with a more powerful one with better optical characteristics, the communication range and reception area improve. By using symmetrical power supply, the throughput improves. Likewise, by using optical filters that eliminate noise, the throughput also improves. We have demonstrated that LiFi data transmission in the vehicle is feasible; low-definition videos were successfully transmitted. The paper acknowledges that there are still various avenues for this work’s improvement.

The purpose of interdisciplinary communication during the early architectural design stage is to achieve the early integration of knowledge in different professional fields, which can help architects to choose correct design development strategies during the early architectural design stage. However, because there is too little information at the early design stage, and design solutions are still rapidly changing and developing, the uncertainties at this stage make it difficult for consultants in other disciplines to provide their views and analysis. In spite of this situation, the emergence of generative modeling is changing design procedures and methods of communication and cooperation for architectural teams, and has brought about a shift in the way architects transmit design information from "what" (declarative information) to "how" (procedural information). Generative modeling is like an aircraft's dashboard: It can provide a basis for interdisciplinary communication, provide interdisciplinary knowledge packages, and bring about a shift in interdisciplinary communication that will reduce the architectural team's communication needs and cost. This study uses a real design case to show the feasibility of generative modeling. Employing generative modeling as a basis, architects can enhance the efficiency of design change and multi-disciplinary communication during the early design stage, integrate specialized knowledge in relevant fields, use this knowledge to formulate design criteria for the next stage, and effectively transmit design decisions. As a consequence, the changes to the cost structure of design revisions and communication between different disciplines has initiated a paradigm shift toward multi-disciplinary communication in architectural design.

The utilization of primary school buildings is multifaceted, primarily due to the high occupancy density, varying thermal preferences among occupants, diverse indoor activities (such as walking, sports, and conversation), and a constant flow of individuals entering and exiting the building. This results in frequent opening and closing of external windows and doors and fluctuations in internal heat gain. Consequently, frequent interactions between the indoor and outdoor microenvironments lead to energy losses. This study conducts a comprehensive literature review on building energy loss stemming from occupant behavior and the interactions between indoor and outdoor microenvironments. Furthermore, it proposes a dynamic real-time monitoring system based on a computer data capture and visualization platform foundation for building energy loss. The research methods include data crawling, data association rule mining, and data association analysis. The research findings yield a universally applicable and informative building energy-saving design theory based on extensive data analysis. Additionally, the system presents information on occupants' behavior and the microclimate data of indoor and outdoor environments on a computer screen, facilitating human-machine communication and enabling timely adjustments to design strategies for new buildings and operation and maintenance strategies for existing buildings.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Smallsats are becoming the predominant electro-optical Earth observation (EO) imaging platforms. While atmospheric correction of smallsat data enhances its utility, an established pathway to do so may constrain accuracy and utility. The alternative, Closed-form Method for Atmospheric Correction (CMAC), developed for smallsat application provides surface reflectance derived solely from scene statistics. In a prior paper, CMAC closely agreed with Land Surface Reflectance Code (LaSRC) software for correction of the four VNIR bands of Landsat-8/9 images for conditions of low to moderate atmospheric effect over quasi-invariant warehouse-industrial targets. Those results were accepted as surrogate surface reflectance to support analysis of CMAC and LaSRC reliability for surface reflectance retrieval in two contrasting environments: shortgrass prairie and barren desert. Reliability was defined and tested through a null hypothesis: the same top-of-atmosphere reflectance under the same atmospheric condition will provide the same estimate of surface reflectance. Evaluated against the prior surrogate surface reflectance, the results found decreasing error with increasing wavelength for both methods. From 58 comparisons across the four bands, LaSRC average absolute error ranged from 0.59% (NIR) to 50.30% (blue). CMAC error was well constrained from 0.01% (NIR) to 0.98% (blue) sustaining the null hypothesis for reliability.

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

This study uses machine learning to predict the convergence results of the Duffing equation with and without damping. The Duffing equation represents a nonlinear second-order differential equation with interesting behavior in undamped free vibration and forced vibration with damping. Convergence alternates randomly between 1 and -1 in undamped free vibration, depending on initial conditions. For forced vibration with damping, multiple factors influence vibration patterns. We utilize the fourth-order Runge-Kutta method to collect convergence results for both conditions. Machine learning techniques, specifically the long short term memory (LSTM) and LSTM-Neural Network (LSTM-NN) method, are employed to predict these convergence values. The LSTM-NN model is a hybrid approach that combines the LSTM method with the addition of hidden layers of neurons. Both the LSTM and LSTM-NN models are thoroughly explored and analyzed in this research. The research process involves three stages: data preprocessing, training, and verification. The results show that the LSTM-NN model becomes more adept at predicting binary datasets, boasting an impressive accuracy of up to 98%. However, when it comes to predicting multiple solutions, the traditional LSTM method outperforms the LSTM-NN approach.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

Thrombosis is the pathological clot formation under abnormal hemodynamic conditions, which can result in vascular obstruction, causing ischemic strokes and myocardial infarction. Thrombus growth under moderate to low shear (<1000 s^-1) relies on platelet activation and coagulation. Thrombosis at elevated high shear rates (>10,000 s-1) is predominantly driven by unactivated platelet binding and aggregating mediated by von Willebrand factor (VWF), while platelet activation and coagulation are secondary in supporting and reinforcing the thrombus. Given the molecular and cellular level information it can access, multiscale computational modelling informed by biology can provide new pathphysiological mechanisms that are otherwise not accessible experimentally, holding promise for novel first-principle-based therapeutics. In this review, we summarize the key aspects of platelet biorheology and mechanobiology, focusing on the molecular and cellular scale events and how they build up to thrombosis through platelet adhesion and aggregation in the presence or absence of platelet activation. In particular, we highlight recent advancements in multiscale modeling of platelet biorheology and mechanobiology and how they can lead to better prediction and quantification of thrombus formation, exemplifying the exciting paradigm of digital medicine.

Abstract: Chloroplast is a new hotspot in the field of plant transformation system of plant genetic engineering. Initially developed in Chlamydomonas and tobacco, it is now feasible in a broad range of species. They exploit the homologous recombination and segregation pathways acting on chloroplast genomes and are based on direct repeats, transient co-integration or co-transformation and segregation of trait and marker genes. Foreign site-specific recombinases and their target sites provide an alternative and effective method for removing marker genes from plastids.Chloroplast genetic engineering has many advantages over nuclear genetic enginering, especially site-specific introduction of foreign genes ,leading to the absence of gene siliency and positon effect,which providing the available to explore the regulation and mechanism of chloroplast genes`expression in vitro .It also can identify the structure and function of the chloroplast genome , the expression of chloroplast affect the nulear genome. In this paper, the basic methodology of chloroplast transformation, the current techniques and applications, and the future possibilities for Chloroplast genetic engineering was reviewed[1-3].

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Chromosome elimination resulting in haploids is achieved by rapid loss of chromosomes from one parent during zygote stage, and is an important procedure to produce doubled haploid (DH) lines in plants. During crosses between an emasculated wheat (Triticum aestivum L.) and a maize (Zea mays L.) as pollen donor, the complete loss of maize chromosomes results in wheat haploid embryos. Through embryo rescue and chromosome doubling process, pure lines with stable traits can be quickly obtained. We here term it as the maize-obligated wheat doubled haploids (mowDH). Although this technology is not new, it remains a practical approach to date. In order to optimize and improve this technology, and to achieve its maximum potential in the winter wheat area of China, this paper reviews the previous and on-going research, proposes a technical scheme for production of wheat DH lines via the maize pollen induction, and presents outlooks on DH research and its application in wheat breeding.

In this paper, we shall introduce the interval-valued spatial error model. Based on the idea of least square method of single-valued case, we give the parameter estimator for interval-valued spatial error model. The theoretical properties of the proposed estimator are proved. Finally, we give the numerical analysis and a real example.

Transition between free-surface and pressurized flows is an crucial phenomenon in many hydraulic systems, including water distribution systems, urban drainage systems, etc. During the transition, the force exerted on the structures changes drastically, thus it is meaningful to simulate this process. However, severe numerical oscillations are widely observed behind filling-bores, causing unphysical pressure variations and even computation failure. In this paper, some oscillation-suppressing approaches are reviewed and evaluated on a benchmark model. Then a new oscillation-suppressing approach is proposed to admit numerical viscosity when the water surface is at proximity of conduct roof which has first order accuracy. This approach adds numerical viscosity when water surface is at the proximity of conduct roof. It can sufficiently suppress numerical oscillations under an acoustic wave speed of 1000m/s and is simple to apply. In comparison with two experiments, the simulation results of this method show good agreement and little numerical oscillations. The results in this paper can help readers to choose an appropriate oscillation-suppressing method to improve the robustness and accuracy of flow regime transition simulations.

Scaffoldings play a critical role as temporary structures in supporting construction processes. Accidents at construction sites frequently stem from issues related to scaffoldings, including insufficient support caused by deviations from the construction design, insecure rod connections, or absence of cross bracing, which result in uneven loading and potential collapse, leading to casualties. In this study, we introduce a deep-learning-based, augmented reality (AR)-enabled system called scaffolding assembly deficiency detection system (SADDS) to assist field inspectors in identifying deficiencies in scaffolding assemblies. Inspectors have the flexibility to utilize SADDS through various devices, such as video cameras, mobile phones, or AR goggles (i.e., Microsoft HoloLens 2), for automated detection of deficiencies in scaffolding assemblies. The training test yielded satisfactory results, with a mean average precision of 0.89 and individual precision values of 0.96, 0.82, 0.90, and 0.89 for “qualified” frames and frames with the “missing cross-tie rod,” “missing lower-tie rod,” and “missing footboard” deficiencies, respectively. Field tests conducted at two construction sites demonstrated improved system performance compared to that in the training test. However, these field tests also revealed certain limitations of the SADDS system.

Over the few decades, cancer-associated mortalities and morbidities were continuously increased worldwide despite sophisticated technological advancements. Pharmaceutical interventions associated with drugs exhibit a high degree of side effects and toxicities in addition to very high costs. Subsequently, to reduce or to vanish the side effects and high costs, researchers are now exploring natural bioactive compounds such as quercetin in its nanoformulations along with biologics as cargo delivery vehicles. Quercetin along with mesenchymal stromal lineage-derived extracellular vesicles (EVs) possesses an anti-cancer potential that can be explored to treat hepatocellular carcinoma (HCC). Exerting enhanced effect, nano quercetin synergistically with EVs triggers the anti-cancer mechanisms by regulating and dysregulating several signalling mechanisms including NF-κB, p53, JAK/STAT, MAPK, Wnt/β-catenin and PI3K/AKT, in addition to PBX3/ERK1/2/CDK2, and miRNAs modulation. In addition, findings regarding the potential checkpoints of anti-cancer signalling pathways were investigated that offer opportunities to develop engineered EVs incorporated with nano quercetin for the development of novel therapeutics to treat HCC in future. In this present mechanistic review, we abridged the regulation of such signalling mechanisms synergetic approach of nano quercetin and EVs. The regulatory role of EVs in the manifestation of innumerable miRNAs has also been tailed with special context to HCC.

Managing severe bleeding, particularly in soft tissues and visceral injuries, remains a significant challenge in trauma and surgical care. Traditional hemostatic methods often fall short in wet and dynamic environments. This study addresses the critical issue of severe bleeding in soft tissues, proposing an innovative solution using a Polyethylene Glycol (PEG)-based hydrogel combined with zinc oxide (ZnO). The developed hydrogel forms a dual-network structure through amide bonds and metal ion chelation, resulting in enhanced mechanical properties and adhesion strength. The hydrogel, exhibiting excellent biocompatibility, is designed to release zinc ions, promoting coagulation and accelerating hemostasis. Comprehensive characterization, including gelation time, rheological properties, microstructure analysis, and swelling behavior, demon-strates the superior performance of the PEG/ZnO hydrogel compared to traditional PEG hydro-gels. Mechanical tests confirm increased compression strength and adhesive properties, crucial for withstanding tissue dynamics. In vitro assessments reveal excellent biocompatibility and en-hanced procoagulant ability attributed to ZnO. Moreover, in vivo experiments using rat liver and tail bleeding models demonstrate the remarkable hemostatic performance of the PEG/ZnO hy-drogel, showcasing its potential for acute bleeding treatment in both visceral and peripheral sce-narios.

Objectives: This study aimed to analyze the awareness of local residents regarding healthcare projects and to suggest some ideas for the revision of local ones. Methods: To delve into the opinions of local residents, the author of this study created a questionnaire composed of eight questions on the general characteristics of the respondents, eight questions on satisfaction with health centers, 16 questions on the awareness of healthcare projects, and 22 questions on local healthcare. The survey was conducted for 409 residents who visited public centers in Gimcheon from 15 March to 14 April 2021. Results: Data analysis revealed the following: The proportion of local residents who use health centers was 39.1%, and those users visit health centers, on average, 3.92 times a year. Among healthcare projects, the project known by the highest proportion of people was vaccinations (84.5%), which was also the project that was most used (38.1%). Among healthcare projects needed in the with-COVID-19 age, respondents awarded the highest score to vaccinations (4.15 points on a five-point Likert scale) and the second highest score to infectious disease management (4.12). Conclusions: For healthcare projects, central and local governments should focus on activating vaccinations, solving the problem of medical accessibility through untact remote treatment and establishing national infectious disease-specializing hospitals and local infectious disease management based on such national hospitals.

This is the fourth part of [6] on the existence of K¨ahler Einstein metrics of the general type I almost homogeneous manifolds of cohomogeneity one. We actually carry out all the results in [8] to the type I cases. In part II [14], we obtained a lot of new K¨ahler-Einstein manifolds as well as Fano manifolds without K¨ahler-Einstein metrics. In particular, by applying Theorem 15 therein, we have complete results in the Theorems 3 and 4 in that paper. However, we only have some partial results in Theorem 5 there. In this note, we shall give a report of recent progress on the Fano manifolds Nn,m when n > 15 and N′n,m when n > 4. We actually give two nice pictures for these two classes of manifolds. See our Theorems 1 and 2 in the last section. Moreover, we post two conjectures. Once we could solve these two conjectures, the question for these two classes of manifolds would be completely solved. With applying our results to the canonical circle bundles we also obtain Sasakian manifolds with or without Sasakian-Einstein metrics. That also give some open Calabi-Yau manifolds.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Human epidermal growth factor receptor 2 (HER2), a targetable transmembrane glycoprotein receptor of the epidermal growth factor receptor (EGFR) family, plays a crucial role in cell proliferation, survival, and differentiation. Aberrant HER2 signaling is implicated in various cancers, particularly breast and Gastric cancer, where HER2 overexpression or amplification correlates with aggressive tumor behavior and poor prognosis. Her2 activating mutations contribute to accelerated tumorigenesis and metastasis. This review provides an overview of HER2 biology, signaling pathways, mechanisms of dysregulation, diagnostic approaches, and therapeutic strategies targeting HER2 in cancer. Understanding the intricate details of HER2 regulation is essential for developing effective targeted therapies and improving patient outcomes.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

Changes in coastal topography can affect the ecological environment and marine industries. In this study, we analyzed the patterns and causes of changes in shoreline and undersea topography in the Nakdong River estuary in the southeast of South Korea using depth and shoreline surveys of the estuary, as well as data on discharge, suspended sediments, and precipitation in the Nakdong River basin. The results showed that erosion and sedimentation occurred repeatedly owing to complex factors such as the discharge of the estuary and invasion by open sea waves. However, no clear unilateral trend was observed. Unlike previous survey data, a large amount of erosion occurred in the second half of 2020. Previously, sedimentation was the main process, but erosion occurred rapidly, which was observed in the summer of 2020 when the erosion was three times higher than that in other periods owing to the severe rainy season and torrential rains for over a month. In addition, regarding the flow rate and force of the river water outflow, the amount of discharge increased rapidly, causing erosion. Moreover, a strong typhoon in the summer of 2020 affected the topography of the estuary.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

Some researchers in Taiwan argue that the current mechanism by which government subsidies are allocated for smart city demonstration projects warrants improvement. A comprehensive literature review determined that the development potential of smart cities should be prioritized in site selection for such demonstration projects. This study developed an evaluation framework on the basis of multi-criteria evaluation methods to enable the identification of suitable smart community demonstration sites. Evaluation criteria were first identified through the Delphi method. Next, the weights of each criterion were derived through the analytic hierarchy process. Furthermore, the capability of the proposed evaluation model was determined through simulation testing.

Quantitative and qualitative fuzzy measures have been proposed to hesitant fuzzy sets (HFSs) from different points. However, few of the existing HFSs fuzzy measures refer to the grey relational analysis (GRA) theory. Actually, the GRA theory is very useful in the fuzzy measure domain, which has been developed for such the intuitionistic fuzzy sets. Therefore, in this paper, we apply the GRA theory to the HFSs and interval-valued hesitant fuzzy sets (IVHFS) domain. We propose the HFSs grey relational degree, HFSs slope grey relational degree, HFSs synthetic grey relational degree and IVHFSs grey relational degree, which describe the closeness, the variation tendency and both the closeness and variation tendency of HFSs and closeness of IVHFSs, respectively, greatly enriching the fuzzy measures of HFSs. Furthermore, with the help of the TOPSIS method, we develop the grey relational based MADM methodology to solve the HFSs and IVHFSs MADM problems. Finally, combined with two practical MADM examples about energy policy selection with HFSs information and emergency management evaluation with IVHFSs information, we obtain the most desirable decision results, and compared with the previous methods, the validity, effectiveness and accuracy of the proposed grey relational degree for HFSs and IVHFSs are demonstrated in detail.

Erosion caused by the repeated impact of particles on a substance surface is a usual wear method resulting in gradual and continual loss of objects. It is a crucial problem in several modern industries because their surfaces are frequently subjected to destructive erosive situations. Polymers and their hybrid materials include several applications to be used as a coating in the form of powder for different applications. This review paper aims to provide extensive information on the erosion behavior of thermoset and thermoplastic neat resin and their hybrid materials composites. Focus is specifically paid to highlight the influence of properties of selected materials, impingnation parameters such as incident Angle of erodent, impact velocity of erodent, erodent nature, and the erosion mechanism. The review further extends the information about the erosion techniques and numerical simulation methods used for wear studies of surfaces. An investigation has been carried out for researchers to explore the selection of materials and methods in terms of conditions and parameters to meet the current and future needs and challenges for the protection of surfaces of the advanced industries. During review according to the findings achieved from the literature of the past fifty years, it has been noted that the thermoplastic nature of the composite is a key component to determine the anti-wear properties, the composites with lower glass transition, higher ductility, and greater crystallinity can provide better protection to erosion in advance surface applications.

In the rapidly evolving landscape of genetic engineering, the advent of CRISPR-Cas technologies has catalyzed a paradigm shift, empowering scientists to manipulate the genetic code with unprece-dented accuracy and efficiency. Despite the remarkable capabilities inherent to CRISPR-Cas sys-tems, recent advancements have witnessed the integration of small molecule to augment their functionality, introducing new dimensions to the precision and versatility of gene editing applica-tions. This review delves into the synergy between CRISPR-Cas technologies and small molecule drugs, elucidating the pivotal role of chemicals in optimizing target specificity and editing efficiency. By examining a diverse array of applications, ranging from therapeutic interventions to agricultural advancements, we explore how the judicious use of chemicals enhances the precision of CRISPR-Cas-mediated genetic modifications. In this review we emphasize the significance of small molecule drugs in fine-tuning the CRISPR-Cas machinery, which allows researchers to exert meticulous con-trol over the editing process. We delve into the mechanisms through which these chemicals bolster target specificity, mitigate off-target effects, and contribute to the overall refinement of gene edit-ing outcomes. Additionally, we discuss the potential of chemical integration in expanding the scope of CRISPR-Cas technologies, enabling tailored solutions for diverse genetic manipulation challenges. As CRISPR-Cas technologies continue to evolve, the integration of small molecule drugs emerges as a crucial avenue for advancing the precision and applicability of gene editing techniques. This re-view not only synthesizes current knowledge but also highlights future prospects, paving the way for a deeper understanding of the synergistic interplay between CRISPR-Cas systems and chemical modulators in the pursuit of more controlled and efficient genetic modifications.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

[Introduction]: In the contemporary international financial environment, marked by intricate complexities and increasing uncertainties, the impact of exchange rate fluctuations on national economies has become increasingly significant. In this context, this study uses the Chinese economy as a case study to delve deeply into the interaction effects between macroprudential and monetary policies, analyzing how these policies jointly address economic instability. The aim is to offer new perspectives and strategies for stabilizing the global economic and financial landscape. [Methods]: This paper constructs an open-economy Dynamic Stochastic General Equilibrium (DSGE) model specifically tailored for China, incorporating Bayesian estimation and numerical simulation techniques. The study meticulously examines how macroprudential and monetary policies can be coordinated to achieve economic stability in response to exchange rate shocks. [Results]: The research finds that (1) targeted coordination of macroprudential and monetary policies towards asset prices and price levels can maintain stability under exchange rate shocks; (2) the effective implementation of such coordinated policies not only mitigates the fluctuations in asset prices due to exchange rate shocks but also enhances the level of societal welfare; (3) in terms of choosing an exchange rate regime, a managed floating rate system can prevent policy overlaps and conflicts that might occur in a floating rate system during the coordination of macroprudential and monetary policies, thus offering comparative advantages. [Discussion]: The findings underscore the importance of policy integration in a dynamic and complex global economic environment. They provide policy recommendations for China and other emerging market countries on how to effectively maintain economic stability through the synergistic interplay of macroprudential and monetary policies amid fluctuations in exchange rates and asset prices.

Predicting the outcome of a future game between two National Basketball Association (NBA) teams poses a challenging problem of interest to statistical scientists as well as the general public. In this article, we formalize the problem of predicting the game results as a classification problem and apply the principle of maximum entropy to construct NBA maximum entropy (NBAME) model that fits to discrete statistics for NBA games, and then predict the outcomes of NBA playoffs by the NBAME model. The best NBAME model is able to correctly predict the winning team 74.4 percent of the time as compared to some other machine learning algorithms which is correct 69.3 percent of the time.

Avian influenza viruses (AIVs) are highly contagious respiratory viruses of birds, lead-ing to significant morbidity and mortality globally and causing substantial economic losses to the poultry industry. Since their first isolation in 2013, the Asian-origin H5N1 highly pathogenic avian influenza viruses (HPAI) of clade 2.3.4.4b have undergone unprecedented evolution and re-assortment of internal gene segments and have spread to Asia, Europe, Africa, and America, caus-ing outbreaks in all the poultry categories. Novel epidemiological and pathobiological character-istics, distinct from other clades, are specific of clade 2.3.4.4b viruses. Wild waterfowl, the natu-ral reservoir of AIVs, are frequently found infected with clade 2.3.4.4b viruses, which can also cause high morbidity and mortality in these birds. The sustained clade 2.3.4.4b virus circulation in waterfowl has also led to virus infection in other wild bird species, with implications for the conservation of endangered species. Furthermore, clade 2.3.4.4b viruses have been isolated in var-ious wild and domestic mammals worldwide, and critical mutations related to virus adaptation to mammalian species have been identified, raising concerns about virus spillover to humans. The main clinical signs, and anatomopathological findings associated to clade 2.3.4.4b virus infection in birds and non-human mammals are hereby summarized.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

The anti-inflammatory effect of ginsenoside Rh2 (GRh2) is one of the most important ginsenosides. The purpose of this study is to identify the anti-inflammatory and antioxidant effects of GRh2 after LPS challenge lung injury animal model. GRh2 reduced LPS-induced NO, TNF-α, IL-1, IL-4, IL-6 and IL-10 productions in lung tissues. GRh2 treatment decreased the histological alterations in the lung tissues and BALF protein content and total cells number also diminished in LPS-induced lung injury mice. Moreover, GRh2 blocked iNOS, COX-2, the phosphorylation of IκB-α, ERK, JNK, p38, Raf-1 and MEK protein expression which is corresponded to the growth of HO-1, Nrf-2, catalase, SOD and GPx expressions in LPS-induce lung injury. An experimental study has suggested that GRh2 has provided with anti-inflammatory effects in vivo, and its potential therapeutic efficacy in major anterior segment lung diseases.

Primary urethral malignancies are rare in clinical practice and elderly female are prone to suffer. The cause of PUC is unknown and may be related to long-term chronic inflammation, infection, sexual intercourse, pregnancy and irritation of the urethra. Incipient symptom of PUC is not distinctness and can easily lead to misdiagnosis. The final diagnosis relied on transvaginal ultrasound-guided mass biopsy and urethral biopsy. Early tumor treatment is mainly based on surgical resection. For advanced tumors, it is recommended to adopt a comprehensive treatment plan combining surgery, radiotherapy and chemotherapy We report this case with the aim of bringing attention to that primary urethral cancer progresses rapidly and has a poor prognosis, it is urged to call for a need of diagnostic and treatment specification.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

In the TANGO study, the long-term noninferior efficacy of switching to dolutegravir/lamivudine (DTG/3TC) compared to continuing tenofovir alafenamide–based regimens was demonstrated in treatment-experienced adults with HIV. However, there is limited real-world data comparing the effectiveness and safety of bictegravir/emtricitabine/tenofovir alafenamide fumarate (BIC/FTC/TAF) and DTG/3TC in Asia. This retrospective observational study, conducted at a designated HIV-care hospital from March 2019 to January 2023, aimed to address this gap. Demographic, clinical, and laboratory data, including HIV viral loads and lipid profiles, were collected and analyzed. The primary outcome was the proportion of patients with HIV RNA <50 copies/mL at week 48 in both groups, utilizing a snapshot, per-protocol–exposed population. A total of 1086 patients were included, with 511 in the DTG/3TC group and 575 in the BIC/FTC/TAF group. At week 48, 98% of patients in the DTG/3TC group and 94% in the BIC/FTC/TAF group achieved HIV RNA <50 copies/mL (p <0.01). Logistic regression analysis identified risk factors for detectable viral loads at week 48, including HIV RNA >100,000 copies/mL (AOR 5.13, 95% CI 1.42–18.53), low-level viremia (AOR 3.91, 95% CI 1.07–14.25), and record of virologic failure ≥2 times (AOR 4.21, 95% CI 1.64–10.85) before the switch. Furthermore, no significant difference was found between the DTG/3TC and BIC/FTC/TAF regimens (AOR: 1.51, 95% CI 0.70–3.24). In conclusion, the study demonstrates that the effectiveness and safety profiles of DTG/3TC and BIC/FTC/TAF were comparable in treatment-experienced adults with HIV, particularly among those with undetectable viral loads at baseline.

Visual data on the geographic distribution of carbon storage helps policy maker to formulate countermeasures on global warming. However, Taiwan, as an island showing diversity in climate and topography, had lacked valid visual data in distribution of forest carbon storage between the last to forest surveys (1993-2015). This study established a model to achieve an estimation that capable to demonstrate the distribution of forest carbon storage. This model uses land use, stand morphology, carbon conversion coefficient databases accordingly for 51 types of major forest in Taiwan. An estimation on 2006 was conducted and shows an overall carbon storage of 165.65 Mt C, with forest carbon storage per unit area of 71.56 t C ha–1, where natural forests and plantations respectively contributed of 114.15 Mt C (68.9%) and 51.50 Mt C (31.1%). By assuming no change in land use type, the carbon sequestration from 2006 to 2007 by the 51 forest types was estimated to be 5.21 Mt C yr–1 using historical tree growth and mortality rates. The result reflects the reality of the land use status and event of coverage shifting with time by combining to the two forest surveys in Taiwan.

Leaf variegation pale yellowing is observed in the Calcineurin B-Like-Interacting Protein Kinase14 (CIPK14) overexpression line (oeCIPK14) and double knockout WHIRLY1/WHIRLY3 (why1/3) lines of Arabidopsis, the distribution of WHIRLY1 (WHY1) protein between plastids and the nucleus are affected by the phosphorylation of WHY1 by CIPK14. To elucidate the coregulation of CIPK14 and WHIRLY1/WHIRLY3 mediated leaf pale yellowing, a differential proteomic analysis is conducted between the oeCIPK14 variegated (oeCIPK14-var) line, why1/3 variegated (why1/3-var) line and wild type (WT). More than 800 protein spots are distinguished on each gel, 67 differential abundance proteins (DAPs) are identified by matrix-assisted laser desorption ionization-time of flight/time of flight mass spectrometry (MALDI-TOF/TOF-MS), of which, 34 DAPs are in the oeCIPK14-var, 33 DAPs are in the why1/3-var compared to WT. Five overlapping proteins differentially change both in the oeCIPK14-var and in the why1/3-var. They are ATP-dependent Clp protease proteolytic subunit-related protein 3 (ClpR3), Ribulose bisphosphate carboxylase large chain (RBL), Beta-amylase 3 (BAM3), Ribosome-recycling factor (RRF), Ribulose bisphosphate carboxylase small chain (RBS). Bioinformatics analysis show that most of DAPs are involved in photosynthesis, defense and antioxidation pathway, protein metabolism, amino acid metabolism, energy metabolism, malate biosynthesis, lipid metabolism and transcription. Thus, the photosystem parameters are measured that the content of chlorophyll, the photochemical efficiency of PSⅡ (Fv/Fm), and electron transport rates (ETR) decrease in the why1/3-var and oeCIPK14-var, but the non-photochemical quenching (NPQ) increases. Both mutants show high sensitivity to strong light. Based on the annotation of DAPs from both why1/3-var and oeCIPK14-var lines, we conclude that CIPK14 phosphorylation mediated WHY1 deficiency in plastids is related to impairment of protein metabolism leading to chloroplast dysfunction.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

To win a taekwondo competition, more points must be scored, and the key to scoring points is to improve the motor performance of the kick. The wing kick is an offensive and defensive maneuver. Core stability appears to be important for improving athletic performance, but the specific relationship and effect of core stability on athletic performance in the aerial phase of taekwondo is unclear. The aim of this study was to investigate the relationship between core stability and athletic performance in taekwondo in order to provide appropriate theoretical support for training and to help coaches and athletes to improve athletic performance. A total of 16 subjects (height: 167.34±9.2 cm; weight: 61±8.96 kg; age: 24.7±3.25 years) were studied. Data were captured using 13 infrared cameras at 120Hz, kinematic and kinetic data were captured using a motivated motion capture system, and the data were exported to Visual3D in order to calculate the execution time of the aerial phase, the angular momentum of the left lower extremity, and MVC analysis of the EMG using EMG works. The core stability level of the subjects were measured using the Sahrmann Core Stability Test (SCST) to correlate with the other data, and then the subjects were grouped according to their core stability levels and the data from both groups were analyzed with t-tests. Results During the double fly lifting of aerial segments, SCST levels showed a very strong negative correlation with execution time (r= -0.739) and there was a statistically significant difference in execution time between high and low SCST levels (p &lt; 0.001), and the desired negative correlation was also seen in lower limb angular momentum X-axis (thigh r= -0.6294, shank r= -0.536, foot r= -0.6175), especially in the X-axis. The left rectus femoris (LRF) data had greater activation in the low SCST group(p=0.0019*). Through this experiment, we found that athletes with high core stability had faster execution times, lower angular momentum, and higher core muscle activation. Therefore, we conclude that incorporating core stability training into taekwondo training has the potential to improve kicking performance.

Due to the fact that abrasive media can deform flexibly in abrasive flow machining (AFM) making this method easily to polish the complex holes and the curved surface of the hard machining shapes. Although abrasive media dominate the polishing behavior in AFM process, the mechanism of the abrasive media are not easy to understand because of the high viscous gels, therefore, many finishing works need lots of time to design AFM process. Power laws of the abrasive gels is studied here to evaluate the non-Newtonian flow of abrasive gels in complex holes polishing firstly, at the mean time different abrasive gels are utilized to finish the complex holes to follow the results by non-Newtonian flow calculation. Moreover, traditional AFM has difficulty to achieve a uniform roughness of radial distribution in the complex holes polishing because of the non-uniform abrasive forces. So a helical passageway is proposed to create a multiple motion of abrasive medium and to obtain the even surface of the complex holes in AFM process.

Ganoderic Acid (GA), a major bioactive compound isolated from an oriental medicinal mushroom, i.e. Ganoderma tsugae, has traditionally been found to have significant medicinal properties. As a result of GA's poor solubility in water, formulation poses several challenges. Additionally, the traditional method of administering it via alcohol always results in unfavorable patient side effects. In order to overcome these problems, Ganoderma Tsugae extracts obtained by ethanol extraction were encapsulated in nanodispersions by ultrasonic cavitation and solvent evaporation to maximise bioavailability. Resultant nanodispersions contained Ganoderic acid in a hydrophobic core with a mean particle size of no more than 200 nm and a very narrow particle distribution. An analysis of the interactions between the control variables and the process optimisation was conducted using the Response Surface Methodology (RSM). Based on the results of the experiment, it was found that the particle size of nanodispersions was influenced by the Hydrophilic-Lipophilic Balance (HLB) number and the evaporation temperature. Moreover, the physical stability of micellar systems is generally determined by the organic phase within them. Regarding formulation stability, the zeta average of the nanodispersions remained virtually unchanged in solutions with different pH levels and short-term storage (14 days) at room temperature. Overall, it has been demonstrated that Ganoderic acid nanodispersions can be efficiently generated by combining ultrasound cavitation and solvent evaporation.

Depression is the most common chronic mental illness and is characterized by low mood, insomnia, and affective disorders. However, the pathological mechanisms of depression remain unclear. Numerous studies have suggested that the ghrelin/GHSR system may be involved in the pathophysiologic process of depression. Ghrelin plays a dual role in the experimental animals, increasing depressed behavior and decreasing anxiety. By combining several neuropeptides and traditional neurotransmitter systems to construct neural networks, it modifies signals connected to depression. The present review emphasizes the role of ghrelin in neuritogenesis, astrocyte protection, inflammatory factor production, and endocrine disruption in depression. Furthermore, ghrelin/GHSR can activate multiple signaling pathways to produce antidepressant effects, including cAMP/CREB/BDNF, PI3K/Akt, Jak2/STAT3, and p38-MAPK. Given the antidepressant effects of ghrelin/GHSR1a system, it is expected to become a potential therapeutic target for the treatment of depression.

Consumption of refined foods and beverages high in sugar make the teeth susceptible to the formation of biofilm, and lead to dental caries and diseases of the oral cavity such as periodontitis and periodontal disease. The aim of the present study was to determine the ability of selected probiotics to inhibit growth and biofilm formation by the cariogenic bacterium Streptococcus mutans in vitro. We screened strains of latic acid bacteria (LAB) (n=120) from the Bioresources Collection and Research Center (BCRC), saliva of healthy adults and infant stool. The antimicrobial activity of LAB in vitro was evaluated by agar spot culture and co-culture of the S. mutans strains. We determined the effect of heating and dilution factors (2- and 4-fold) on the antagonistic activity of LAB. Antagonistic substances in the spent culture suspensions (SCS) of LAB were precipitated by extraction with ammonium sulphate and chloroform to characterise the protein and lipophilic fractions. Results of co-culturing show that the SCS of the three LAB strains (Lactobacillus pentosus 13-1, 13-4 and Lactobacillus crispatus BCRC 14618) subjected to heat treatment showed significantly high antimicrobial activity. We found that substances produced by L. pentosus 13-4 which have the potential to exhibit antimicrobial properties might be lipophilic proteins. Additionally, we infer that the mechanism of reducing biofilm formation by Lactobacillus strains is associated with sucrose-dependent cell–cell adhesion and the gtfC level of glucosyltransferases (Gtfs) in the biofilm. Native LAB strains screened in our study may be used in chewing gums and other processed foods for preventing tooth decay.

As the leader of the largest economy, President of the United States has substantive influence on addressing the global climate change problem. However, presidential election is often dominated by issues other than energy problems. This paper focuses on the on-going 2016 presidential election, examining the energy plans proposed by the leading Democrat and Republican candidates. Our data from the Iowa caucus survey in January 2016 suggests that voters are more concerned about terrorism and economic issues than environmental relative issues. We then compare the Democratic and Republican candidate’s view of American’s energy future, and evaluate their proposed renewable energy targets. We find that the view on renewable energy is polarized between Democratic and Republican candidates, while candidates from both parties agree on the need for energy efficiency. Results from our ordinal least squares regression models suggest that Democratic candidates have moderate to ambitious goals for developing solar and other renewable energy. The Republican candidates favor fossil fuel and they neglect to provide any plan for renewable energy. In addition, this trend of polarization has grown more significant when compared with the past three presidential elections. Our observation suggests that energy issues need to be discussed more to draw broader attention to salient issues of diversifying and decarbonizing the nation’s energy system.

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

Sialylated milk oligosaccharides (SMOs) is the most important oligosaccharides in human milk oligosaccharides (HMOs), and have a multifunctional health benefit, and the most abundant SMOs are sialyllactose (SLs). The previous studies indicate that the growth of tumor cells, and angiogenesis on tumor tissues with Lewis lung carcinoma, melanoma, and colon carcinoma cells could be prevented by SL. Thus, it has been proposed that SL might be an ideal candidate for the development of anti-angiogenic drugs without any side effects. It has been proposed that the Sialic acid (Sia) can be produced through SL’s hydrolysis, and the dietary Sia is further transported to the brain and other tissues though blood for formation of CMP-Sia, the activated precursor of Sia, and then is catalyzed by polysialyltransferases (polySTs) for synthesis of polysialic acid (polySia) or polysialylation of neural cell adhesion molecule (NCAM). Thus, it’s necessary to study and develop new inhibitors, which not only modulate a proper balance between the gut health and neuros system development, but also inhibit the overexpression of polySia, and thus block the tumor cell migration. In this study, we proposed that 3’-SL and 6’-SL may be more ideal inhibitors comparing with two previous inhibitors, the low molecular weight heparin (LMWH) and cytidine monophosphate (CMP) in the previous studies.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.