In this paper, fiber sensor based on Vernier effect for simultaneous measurement of relative humidity (RH) and temperature is proposed. The sensor is fabricated by coating two kinds of ultraviolet (UV) glue with different refractive indexes (RI) and thicknesses on the end face of a fiber patch cord. Vernier effect is formed by the inner lower-RI polymer cavity and the cavity composed of both polymer films. By calibrating the RH and temperature response of two peaks on the envelope of the reflection spectrum, simultaneous measurement of RH and temperature is realized by solving a set of quadratic equations. Experimental results show that the highest RH and temperature sensitivities of the sensor are 387.3 pm/%RH (in 20%RH to 90%RH) and -533.0 pm/°C (in 15°C to 40°C), respectively. The sensor has merits of low cost, simple fabrication, and high sensitivity, which makes it very attractive for applications that need to simultaneously monitor these two parameters.

Novel Ca3(BTC)2 metal-organic frameworks with different sizes and shapes constructed by Ca2+ and trimesic acid as metal center and ligands respectively were synthesized by a surfactant-assisted method. The relationship between the quantity of surfactant and the particle morphology of the product have been further studied. The samples were characterized by scanning electron microscope, powder X-ray diffraction and Inductively coupled plasma mass spectrometry. The results indicated that the size and shape of Ca3(BTC)2 could be regulated by changing the quantity of surfactant. Rod- and sheet-like Ca3(BTC)2 MOFs have been readily availabled. The removal kinetics of heavy metals of Pb(II) were also studied by rod-like Ca3(BTC)2. The results showed that as-synthesized Ca3(BTC)2 could effectively remove heavy metals of Pb(II) from the sewage.

The chitin synthase B gene is a key enzyme in the chitin synthesis of insect peritrophic matrix (PM), affecting insects' feeding behavior. The chitin synthase B gene has been cloned from the transcription library of Heortia vitessoides Moore. RT-qPCR showed that HvChsb was highly expressed in the larval stage of H. vitessoides, especially on the first day of the prepupal stage, and in the midgut of larvae and the abdomen of adults. After starvation treatment, HvChsb was found to be significantly inhibited with time. After 48 h of starvation, the feeding experiment showed that HvChsb increased with the prolongation of the refeeding time. The experimental data showed that feeding affected the expression of HvChsb. HvChsb was effectively silenced by RNA interference, so its function was lost, significantly decreasing the survival rate of H. vitessoides. The survival rate from larval-to-pupal stages was only 43.33%, accompanied by abnormal phenotypes. It can be seen that HvChsb plays a key role in the average growth and development of H. vitessoides.

Lipid nanoparticles (LNPs) are promising carriers for constructing drug delivery systems (DDSs) in disease treatments. Previous studies have suggested that lipid composition and biophysical properties of LNPs can significantly impact their interaction with cells and tissues, allowing for the development of suitable LNPs for precise drug delivery. Our previous study proposed the concept and facile preparation of reconstituted lipid nanoparticles (rLNPs), which not only have the advantages of traditional LNPs but also contain the lipids of mother cell/tissue. In this study, we have found that brain-derived rLNPs (B-rLNPs) can have much better accumulation to the ischemic area of the ischemic stroke (IS) model than liver-derived rLNPs (L-rLNPs). This homing effect hopefully makes rLNPs a useful tool for developing highly accessible devices with homologous targeting ability for precise drug delivery.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

Transposable elements (TEs), also known as mobile elements (MEs), are interspersed repeats that constitute a major fraction of the genomes of higher organisms. As one of their important functional impacts on gene function and genome evolution, TEs participate in regulating the expression of genes nearby and even far away at transcriptional and post-transcriptional levels. There are two known principal ways by which TEs regulate expression of genes. First, TEs provide cis-regulatory sequences in the genome with their intrinsic regulatory properties for their own expression making them potential factors for regulating the expression of the host genes. TE-derived cis-regulatory sites are found in promoter and enhancer elements, providing binding sites for a wide range of trans-acting factors. Second, TEs encode for regulatory RNAs with their sequences showed to be present in a substantial fraction of miRNAs and long non-coding RNAs (lncRNAs), indicating the TE origin of these RNAs. Furthermore, TEs sequences were found to be critical for regulatory functions of these RNAs including binding to the target mRNA. TEs thus provide crucial regulatory roles by being part of cis-regulatory and regulatory RNA sequences. Moreover, both TE-derived cis-regulatory sequences and TE-derived regulatory RNAs, have been implicated to provide evolutionary novelty to gene regulation. These TE-derived regulatory mechanisms also tend to function in tissue-specific fashion. In this review, we aim to comprehensively cover the studies regarding these two aspects of TE-mediated gene regulation, mainly focusing on the mechanisms, contribution of different types of TEs, differential roles among tissue types, and lineage specificity, based on data mostly in humans.

The phonon modes in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems have been systematically studied by Raman spectroscopy. The new phonon modes of 104 cm^-1, 94 cm^-1, and 89 cm^-1 were found in all these samples. A crude estimate about the wavenumber of the collective vibration of the stable CuO2 plane was given in this paper. The standard deviations of the new phonons in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems were discussed. The results of the calculation indicated that the 104 cm^-1 mode probably stands the c-direction collective vibration of the stable CuO2 plane, the 94 cm^-1 mode stands the a-direction vibration, and the 89 cm^-1 mode stands b-direction vibration. The relevance between these phonons and the superconductivity was discussed. It is found that, as the T_c decreased, the 104 cm^-1 mode and the 94 cm^-1 mode softened, and the 89 cm^-1 mode hardened slightly.

Background: Gestational diabetes is a common complication during pregnancy that can lead to numerous adverse outcomes. Some studies suggest that probiotics may be used to treat gestational diabetes, however, the results remain controversial. We conducted a systematic review and meta-analysis to evaluate the effect of probiotics on blood glucose and pregnancy outcomes in women with gestational diabetes. Methods: A systematic search of PubMed, Embase, and Cochrane databases was performed (start date to August 22, 2023). Primary outcomes included fasting blood sugar (FBS), fasting serum insulin (FSI), homeostasis model assessment of insulin resistance (HOMA-IR), and quantitative insulin sensitivity check index (QUICKI). Secondary outcomes included pregnancy and neonatal outcomes. Results: 15 articles (n = 1006 women) met the inclusion criteria and were included in the analysis. Compared to a placebo, probiotics can decrease FBS (MD -2.58, 95% CI -4.38 to -0.79, p < 0.01), FSI (MD -2.29, 95% CI -3.40 to -1.18, p < 0.01), HOMA-IR (MD -0.56, 95% CI -0.81 to -0.32, p < 0.01), birthweight (MD -101.20, 95% CI -184.62 to -17.77, p = 0.02), neonatal intensive care unit (NICU) (RR 0.60, 95% CI 0.40 to 0.89, p = 0.01), and hyperbilirubinemia (RR 0.31, 95% CI 0.16 to 0.61, p < 0.01), alongside higher QUICKI (MD 0.01, 95% CI 0.00 to 0.01, p < 0.01). However, no other significant results were obtained. Conclusion: Probiotics may improve blood glucose indicators and reduce neonatal hyperbilirubinemia, NICU admissions, and birth weight in women with GDM.

We employed the Riemannian Face Manifold (RFM) as an alternative approach to the conventional linear Euclidean space for explaining the atypicality bias in face likeliness judgments. The RFM posits that the mental representation of faces is better captured as a manifold of stable states, accounting for the nonlinearity in the physical properties of faces. To examine the relationship between physical and psychological distance of morph and typical/atypical faces, we manipulated the parameter k and incorporated a weight function in the Riemannian metric. Our results indicate that the psychological distance between the morph and typical face was longer than that between the morph and atypical face, consistent with prior research on the atypicality bias in perceptual similarity. The RFM approach provides mathematical support and is a powerful tool for studying face perception and recognition, offering potential implications for explaining the other-race effect. Future research can utilize the RFM to investigate individual differences in face recognition abilities and expertise, and how they impact psychological distance and face processing.

Copper-based nanoparticles were synthesized using the glycine–nitrate process (GNP) by using copper nitrate trihydrate [Cu(NO₃)₂‧3H₂O] as the main starting material and glycine [C₂H₅NO₂] as the complexing and incendiary agent. The as-prepared powders were characterized through X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy. Using Cu(NO₃)₂.3H₂O as the oxidizer (N) and glycine as fuel (G), we obtained CuO, mixed-valence copper oxides (CuO + Cu₂O, G/N = 0.3–0.5), and metallic Cu (G/N = 0.7). The XRD and BET results indicated that increasing the glycine concentration (G/N = 0.7) and reducing particle surface area increased the yield of metallic Cu. The effects of varying reaction parameters such as catalyst activity, catalyst dose, and H₂O₂ concentration on nonylphenol-9-polyethoxylate (NP9EO) degradation were assessed. With a copper‐based catalyst in a heterogeneous system, the NP9EO and total organic carbon removal efficiencies were 83.1% and 70.6%, respectively, under optimum operating conditions (pH, 6.0; catalyst dose, 0.3 g/L; H₂O₂ concentration, 0.05 mM). The results suggested that removal efficiency increased with an increase in H₂O₂ concentration but decreased when the H₂O₂ concentration exceeded 0.0.5 mM. Furthermore, the trend of photocatalytic activity was as follows: G/N = 0.5 > G/N = 0.7 > G/N = 0.3. The G/N = 0.5 catalysts showed the highest photocatalytic activity and resulted in 94.6% NP9EO degradation in 600 min.

Refractive index measurements have been an important task for a long time because that index plays an essential role in describing the optical properties of a material. Many methods have been developed to perform that task. Some of them use interferometry to achieve high precision, however these configurations are complicated. Some measure the critical angle using simple structures, but the accuracy is not satisfactory because it is difficult to judge the exact critical angle with intensity variations. Here we propose several new schemes based on measuring the polarization change in the total internal reflection. The proposed method has the merits of simple structure and easy incident angle determination that gives the maximum phase change. Additionally, it is possible to find the material dispersion by measuring the wavelength dependence of the polarization ellipticity. Some useful formulas relating the refractive index with the maximum phase change are obtained. This work can provide valuable alternatives for index measurement.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Tapping panel dryness (TPD) syndrome is a complex disease of Rubber tree (Hevea brasiliensis L.) which causes cessation of latex drainage upon tapping of rubber tree. Rubber tree virus (RTV1) was identified as a novel pathogen associated with rubber tree and a potential causal agent of TPD. RTV1 is a monopartite RNA virus that is linear, non-enveloped and has a single-stranded (ss) positive RNA genome of approximately 6081 nucleotides and is composed of two major open reading frames (ORFs), ORF1 (polyprotein), and ORF2 (movement protein. This study aimed to investigate the possibility of rubber genome encoded tree microRNAs (miRNAs) as novel therapeutic targets against RTV1 using in silico algorithms. Mature rubber tree miRNAs are retrieved from the miRBase database and are used for hybridization of RTV1 using five different five different computational algorithms including miRanda, RNA22, RNAhybrid and psRNATarget. A total of eleven common rubber tree miRNAs were identified based on consensus genomic positions. The consensus of four algorithms predicted the hybridization sites of hbr-miR396a and hbr-miR398 at common locus positions 6676, 1840 respectively. To validate the prediction, secondary structures of the consensual rubber tree miRNAs and free energy of duplex binding were calculated using the RNAfold and RNAcofold algorithms respectively. We created a plot between rubber tree miRNAs and RTV1 ORFs by using Circos algorithm. In this study, we predicted eleven consensual rubber tree miRNAs. Among these miRNAs, hbr-miR398 was identified as the most effectual miRNA that may target the ORF1 gene of the RTV1 genome. The predicted data will be important in the development of rubber trees resistant to RTV1.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

Importance: Because of the high prevalence of myopia in Taiwan, understanding the risk factors for its development and progression is important to public health. Background: This study investigated the risk factors for myopia and their influence on the progression of myopia in schoolchildren in Taiwan. Design: Patients’ clinical records were obtained retrospectively from ophthalmologists. Questionnaires were given to collect demographic information, family background, hours spent on daily activities, myopia progression, and treatment methods. Participants: A total of 522 schoolchildren with myopia from a regional medical hospital in northern Taiwan participated the study. Written informed consent was obtained from the participants of legal age or the parents or legal guardians. Methods: Multivariable regression analyses were performed. Myopia measured in dioptres was analysed, controlling for patients’ family and demographic information as well as their daily behaviours. Main Outcome Results: Children with high myopic parents were more myopic. Earlier onset age of myopia was associated with a higher level of myopia and greater annual myopic progression. Children reporting more near work activities had higher levels of myopia and greater progression of myopia. Lower levels of myopia were associated with more exercise, longer periods of sleep, and better vision care knowledge in children and parents. Intake of food supplements had no effect on myopia. Conclusions and Relevance: In addition to genetics, education, environment, and near work activity can influence the development of myopia. Health policies for schoolchildren should promote protective activities and vision care knowledge in order to protect the eyesight of schoolchildren.

Background: This study aims to compare the impact of early and late post-discharge cardiopulmonary rehabilitation on the outcomes of intensive care unit (ICU) survivors. Methods: The retrospective, cohort study used a sub-database of the Taiwan National Health Insurance Research Database (NHIRD) that contains information of all patients had ICU admission between 2000 and 2012. Early group was defined if patients had received cardiopulmonary rehabilitation within 30 days after ICU discharge, and late group was define as if patients had received cardiopulmonary rehabilitation between 30 days and one year after ICU discharge. The end points were mortality and re-admission during the 3-year follow-up. Results: Among 2136 patients received cardiopulmonary rehabilitation after ICU discharge, 994 was classified early group and other 1142 patients were classified as late group. Overall, early group had a lower mortality rate (6.64% vs 10.86%, p = 0.0006), and a lower ICU readmission rate (47.8% vs 57.97%, p < 0.0001) than late group after 3-year follow-up. Kaplan-Meier analysis showed that early group had significantly lower mortality (p=0.0009) and readmission rate (p<0.0001) than late group. In multivariate analysis, the risk of ICU readmission was found to be independently associated with late group (HR, 1.28; 95% CI, 1.13-1.47). Conclusions: Early post-discharge cardiopulmonary rehabilitation among ICU survivors has the long-term survival benefit and significantly decreases the readmission rate.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

The prediction of drug--target interactions is always a key task in the field of drug redirection. However, traditional methods of predicting drug--target interactions are either mediocre or rely heavily on data stacking. In this work, we merged heterogeneous graph information and obtained effective node information and substructure information based on mutual information in graph embeddings. We then learned high quality representations for downstream tasks, and proposed an end--to--end auto--encoder model to complete the task of link prediction. Experimental results show that our method outperforms several state--of--art models. The model can achieve the area under the receiver operating characteristics (AUROC) curve of 0.959 and area under the precise recall curve (AUPR) of 0.848. We found that the mutual information between the substructure and graph--level representations contributes most to the mutual information index in a relatively sparse network. And the mutual information between the node--level and graph--level representations contributes most in a relatively dense network.

Dry mouth, hyposalivation, or xerostomia is a significant problem in diabetic patients; however, there was no way to relieve these symptoms. This study was aimed to evaluate the effects of Ixeris dentata (IXD) in combination with lactobacillus extract on the salivation rate in diabetes-induced dry mouth, and its mechanism was also investigated. In the streptozotocin-induced diabetes model, dry mouth condition was established as a model. Both control and diabetic rats were treated with a sublingual spray of either water or IXD and subsequently treated with or without a spray of lactobacillus extract. In diabetes condition, the salivary flow rate, amylase activity, and aquaporin-5 and Na+/H+ exchanger (NHE-1) expressions were markedly decreased, whereas they were more significantly recovered in the sequential treatment of IXD-lactobacillus extract than each single treatment. Furthermore, oxidative stress and its related ER stress response were especially regulated in the IXD/lactobacillus extract condition, where the following anti-oxidative enzymes; GSH:GSSG ratio, superoxide dismutase (SOD), and glutathione peroxidase (GPx) were involved. This study suggests that the combination of IXD and lactobacillus would be a potential alternative medicine against diabetes-induced hyposalivation and xerostomia.

Physical inactivity is a well-known risk factor for various non-communicable diseases (NCDs). Sufficient physical activity (PA) is essential for the prevention of NCDs and thus it is imperative to study the current status of PA and its influencing factors among rural residents in China. A population-based survey was conducted in rural areas of Shandong, Shanxi and Yunnan Provinces using a stratified random sampling method. The International Physical Activity Questionnaire Short Form (IPAQ-S) was used to collect the data on PA. A total of 3780 rural residents participated in the survey. The result showed that 22.2% of rural residents were physical inactivity. The proportion of rural residents reporting practice of physical exercise was 54.4%. The most frequently performed physical exercise was walking/brisk walking(78.3%).Binary logistic regression analyses showed that being female, people at age between 15 to 34 years or 60 years old and above, employees of governmental departments/retirees, school students, the unemployed, people with NCDs were risk factors of PA and ethnic minority groups,smoking and alcohol consumption were risk factors of physical exercise. Health promotion programme aiming at increasing people’s PA in rural China is needed and it should focus on the populations groups of the female, people at age 60 years and above ,school students, the unemployed, and people with NCDs.

Plant-derived diterpene synthases (PdiTPSs) play a critical role in the formation of structurally and functionally diverse diterpenoids. However, the specificity or promiscuity of PdiTPSs remains unclear. In order to gain more understanding of this, the sequences of 199 functionally characterized PdiTPSs and their corresponding 3D structures were collected and manually corrected. Then, the correlations among sequences, domains, structures and their corresponding products were comprehensively analyzed. However, those features alone was insufficient for ef-fective product-specific classification of PdiTPSs as these methods could not establish a clear mapping between the enzymes and products. Nevertheless, local structural analysis can identify residues that have been experimentally proven to influence product outcomes through mutagenesis, and these residues exhibit conservation in spatial positioning and physicochemical properties. And aromatic residues surrounding the substrate exhibited selectivity towards its chemical structure. Specifically, tryptophan (W) was preferentially located around the linear substrate geranylgeranyl pyrophosphate (GGPP), while phenylalanine (F) and tyrosine (Y) were preferentially located around the initial cyclized diterpene intermediate. This analysis revealed the functional space of residues surrounding the substrate of PdiTPSs, most of which have not been experimentally explored. These findings provide guidance for screening specific residues for mutation studies to change the catalytic products of PdiTPSs.

The flow behavior of Fe-6.5wt.%Si alloys during hot compression was investigated at temperatures 650–950 °C and strain rates 0.01–10 s^-1. The results showed that the flow stress depended distinctly on the deformation temperatures and strain rates. The flow stress and work hardening rate increased with the decrease of temperature and the increase of strain rate. The activation energy under all the deformation conditions was calculated to be 410 kJ/mol. The constitutive equation with hyperbolic sine function and Zener–Hollomon parameter was developed. The peak stress, critical stress, and steady-state stress could be represented as σ=A+Bln(Z/A). Dynamic recrystallization occurred under the deformation conditions where the values of Z were lower than 10²⁰. Processing maps were established to optimize the processing parameters. The power dissipation efficiency decreased in the high temperature and low strain rate region, increased in the high temperature and high strain rate region, and remained unchanged in other regions with the increase of true strain. Furthermore, the unstable area expanded. The true strain of 0.7 was the optimum reduction according to the processing map. Based on the analysis of surface quality, microstructures, and ordered structures, the optimized processing parameters for the Fe-6.5wt.%Si alloys were the temperature and strain rate of higher than 900 °C and 0.01–10 s^-1, respectively, or 800–900 °C and lower than 0.4 s^-1, respectively.

Crystallization often occurs in the laser welding of amorphous alloys, reducing the amorphous alloys’ properties. So, it is necessary to simulate the temperature field curve of the welding area by computer and then determine the power and laser moving speed of laser welding. In this paper, the temperature field curve of Zr41.2Ti13.8Cu12.5Ni10Be22.5(Vit1) amorphous alloy in laser welding is obtained by finite element analysis. The continuous heating curve (CHT) of Vit1 is fitted by the Vogel-Fulcher-Tammann (VFT) equation and the Kissinger equation. If the temperature field curve intersects with the CHT curve, crystallization occurs. The experiment results show that the VFT equation can be used to predict the crystallization of Vit1 better in laser welding. The tem-perature and welding time are increased by using low welding speed. Therefore, the temperature of the weld zone cannot fall in time, resulting intersection of the temperature field curve and the CHT curve. So, crystallization can be avoided if the welding speed is controlled within a rea-sonable range, and the highest temperature is kept under the CHT curve.

Cylindrical Fe-6.5wt.% Si bars with 7.5 mm in diameter were successfully fabricated from as cast ingot through three rolling stages within 10 passes: rough rolling at 850–900 °C and 8–10 m/min, medium rolling at 800–850 °C and 10–15 m/min, and finish rolling at 800–850 °C and 12–18 m/min. The evolution of microstructure, texture and ordered structure, and the mechanical property are investigated. The results showed that the grains were refined by the hot bar rolling. Area fractions of the {100}<011> oriented grains and the {011}<100> oriented grains decreased to 0 during the hot bar rolling. Whereas, the {100}<001> component, the {011}<211> component and the {112}<110> component increased, and γ fiber with {111}<110> component was dominant. DO₃ ordered phase were suppressed, and B2 ordered domains were refined after the hot bar rolling. Ductility of the as rolled bar was higher than that of the rotary swaged bar, due to the absence of the DO₃ ordered phase and the fine grains in the rolled bar. Hence, the hot bar rolling technology is an excellent process to fabricate the Fe-6.5wt.% Si bars.

Background Successful treatment for patients with metastatic colorectal cancer who failed to response to first-line treatment has been a challenge due to their low response rate for later-line treatment and poor progression free survival and overall survival. The application of dendritic cell-cytokine-induced killer cells (DC-CIK) immunotherapy combined with conventional treat-ment, either surgical resection or chemotherapy, showed improvement in survivals in first-line treatment for metastatic colorectal cancer. In this retrospective study, we aimed to evaluate the benefit of dendritic cell-cytokine-induced killer cells (DC-CIK) immunotherapy for patient with refractory metastatic colorectal cancer. Methods A total of 20 patients with refractory metastatic colorectal cancer receiving cell-cytokine-induced killer cells (DC-CIK) immunotherapy were enrolled to this study. Among these patients, 11 patients responded to the treatment and the remaining 9 patients did not. All patients were followed for at least one years and the determination of treatment response was mainly based on image study at 6 months after the completion of treatment. Data were analyzed with Kaplan-Meier method and log-rank test. Results The treatment response rate of the study group is 55% (11/20). The median progression free sur-vival (PFS) and median overall survival (OS) of responsive patients was 7 months and 12 months, respectively. The median overall survival of irresponsive patients was 9.5 months. Four responsive patients received subsequent metastectomy or cytoreduction plus hyperthermic in-traperitoneal chemotherapy surgery (CRS + HIPEC). Conclusion DC-CIK cell-based immunotherapy may provide benefits for patients with refractory mCRC with improved response rate and progression free survival.

Artificial Intelligence (AI) is a breakthrough technology that has been widely applied in many fields and its use in pharmacy is also gaining increasing attentions. Recently, ChatGPT, a newly developed virtual assistant and large language model, is showing strong ability in writing, which makes it a potential tool for review writing. Here in our study, we employ the public available ChatGPT and try to instruct it to generate a mini review on the topic of “lipid-based drug delivery systems” by conversation. Our results showed that ChatGPT can give reasonable outline for this topic and give seemingly sentences with concluding wording, which can give useful information to the readers. However, the accuracy and consistence of the review are not fully guaranteed and there is lack of reliable citations. Therefore, it is concluded that ChatGPT can only give general knowledge on the selected topic, but not capable of giving in-depth discussion. The generated review article can be a useful but occasionally unprecise electronic encyclopedia instead of rigorous scientific literature, which can give benefit for pharmaceutical education and interchange to some extent.

Short-form video has taken over social media and attracted attention from advertisers. As brands shift their advertising spending to short-form video social platforms, doubts remain about the advertising efficacy on these platforms, especially given the skyrocketing advertising costs in recent years. In a large-scale randomized experiment on ByteDance in collaboration with an automobile brand, we show a significant effect of the advertising campaign on ByteDance, compared with effects reported in other studies. Exposed users are eight times more likely to convert from outside than from within ByteDance, which raises the importance of information sharing between the platform and brands. When considering conversions outside ByteDance, the average cost per conversion, which brands commonly use to evaluate the cost of campaigns, shrinks by 5 or 25 times, depending on the methods used to calculate it. Information sharing can also affect a brand’s targeting strategy. While commonly used demographic variables by the automobile brand are effective for target marketing with only platform data, they are not when considering conversions outside ByteDance. Instead, a behavioral variable proposed herein (prior brand home page visits) effectively moderates the advertising effect but has no effect when including only platform data in the analysis.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Photodynamic therapy has been applied endoscopically to treat early esophageal cancer. However, the long-term survival outcome of this treatment option is unknown in literature. Patients and Method: The patients of early esophageal cancer (clinical stage I) treated with photophrin based photodynamic therapy were analyzed for their long-term survival outcome and compared to those patients undergoing esophagectomy by a single surgeon for stage I disease. Results: There were 15 and 16 patients undergoing PDT and esophagectomy enrolled in the current study respectively. Complete response was achieved in 10 (66.7%) patients after PDT. After adjuvant chemoradiation (CCRT) complete response was achieved in 13 patients (86%). There is no mortality after PDT. Severe complication was detected in 3 patients including trachea-esophageal fistulae, esophageal stenosis and skin photosensitivity respectively. With a median follow-up duration of 110.2 months (+9.6 months) for the patients after PDT, there were 4 and 3 recurrence in the primary tumor site and regional lymph node respectively with 73.3% of successful local control rate of the primary tumor. There were 7 (46.7%) patients died during clinical follow-up of this cohort with 5 (33.3%) from disease progression of esophageal cancer and two from other diseases respectively. The five-year survival rate after PDT is 64.3%, whereas 70.9% of the patients after esophagectomy without significant difference of these two group of patients (P=0.72). Conclusion: Our preliminary results suggested that PDT might provide an equivalent long-term oncological outcome as compared to that done by esophagectomy for early esophageal cancer. A prospective randomized clinical trial comparing the results with esophagectomy and other endoscopic abrasive therapies is warrant in the future.

The effects of 1%~5% cold compression on the mechanical properties, microstructure and residual stress of 7050 aluminum alloy were investigated, and the results were applied to the complex die forging with stiffener structure. The results show that with the increase of cold compression, the tensile strength of forging decreases gradually, but the conductivity and fracture toughness of the forging have little change. TEM microstructure shows that with larger cold compression (5%), the dislocation density was relatively higher, which promoted the precipitation and growth of precipitated phases at positions with higher dislocation density during aging process. The ultrasonic tests of residual stress show that with the increase of cold compression, the residual stress in the forging decreases first, and then increases when cold compression reaches 5%. The results of the die forging of 7050 aluminum alloy with bar structure show that the residual stress of the die forging is obviously eliminated after 2-4% cold compression, and the deformation after machining is obviously less than of the uncompressed forgings. The combination of bar and web is more beneficial to the uniform distribution of residual stress of the die forging with bar structure.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

The buildup dynamics of diode-pumped passively mode-locked solid-state laser is thoroughly explored by the real-time measurement with temporal sampling rate up to 40 GHz. A concise cavity is developed to ensure the transient dynamics purely arising from the gain medium and saturable absorber. Experimental results reveal that the laser output in the buildup process exhibits numerous passively Q-switched pulses followed with a damped relaxation oscillation prior to the stable mode locking. Furthermore, it is confirmed that the laser output has already displayed single clean mode-locked pulses inside the first several Q-switched envelopes before stepping into the stage of relaxation oscillation. The present real-time exploration is expected to provide important information for practical applications with temporal modulation of the pump intensity.

COVID-19 is a highly infectious respiratory illness caused by SARS-CoV-2, and acute lung injury (ALI) is the major cause of COVID-19. The challenge in studying SARS-CoV-2 pathogenicity is the limited availability of animal models. Therefore, it is necessary to establish animal models that can reproduce multiple characteristics of ALI to study therapeutic applications. The present study established a mouse model that has features of ALI that are similar to COVID-19 syndrome to investigate the role of ACE2 and the administration of the Chinese herbal prescription NRICM101 in ALI. Mice with genetic modifications, including overexpression of human ACE2 (K18-hACE2 TG) and absence of ACE2 (mACE2 KO), were intratracheally instillated with hydrochloric acid. The acid intratracheal instillation induced severe immune cell infiltration, cytokine storms, and pulmonary disease in mice. Compared with K18-hACE2 TG mice, mACE2 KO mice exhibited dramatically increased levels of multiple inflammatory cytokines (IL-6, TNF-α, and TGF-β1) in bronchoalveolar lavage fluid, histological evidence of lung injury, and dysregulation of MAPK and MMP activation. In mACE2 KO mice, NRICM101 could ameliorate the disease progression of acid-induced ALI. In conclusion, the established mouse model provided an effective platform for researchers to investigate pathological mechanisms and develop therapeutic strategies for ALI, including COVID-19-related ALI.

The objective of this study was to review the study design and preliminary results of the Recovery trial and analyze the implementability of the Recovery trial by comparing it with the European Discovery trial.Method: The study design of the Recovery trial in the latest version of protocol was described and deeply analyzed to address the issue of implementation of the trial. A comparative analysis of study design and implementation between the UK Recovery trial and the European Discovery trial was conducted following the description.Results: The Recovery trial is a pragmatic, randomized, controlled, adaptive, open-label clinical trial. The study design of the Recovery trial was reported in the ISRCTN registry, the EU Clinical Trials Register and the U.S. National Library of Medicine ClinicalTrials.gov registry. Initially published on the 13^th March 2020, the study protocol of the Recovery trial has been updated five times at the time of this writing. More than 11,000 patients have been enrolled and 80% have completed the follow-up. Thousands of health care professionals at 175 Trusts in the UK have been involved. Conclusion: The Recovery trial applies a study design to address the issue of implementation in the context of the COVID-19 pandemic and emergency. It was conceptually pragmatic with a clear vision to address the top priority: the control of mortality and rational use of scarce resources. By contrast, the Discovery trial was designed as an intellectual exercise and consequently failed to address the issue of implementation in emergency.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

Currently, data regarding optimal treatment modality, response, and outcome specifically for N3 head and neck cancer are lacking. This study aimed to compare the treatment outcomes between definitive concurrent chemoradiotherapy (CCRT) to the neck and upfront neck dissection followed by adjuvant CCRT. 93 N3 squamous cell carcinoma head and neck cancer patients were included. Primary tumor treatment was divided to definitive CCRT (CCRT group) or curative surgery followed by adjuvant CCRT (surgery group). Neck treatment was also classified into two treatment modalities: definitive CCRT to the neck (CCRT group) or curative neck dissection followed by adjuvant CCRT (neck dissection group). Overall, the 2-year overall survival (OS), local recurrence-free survival (LRFS), regional recurrence-free survival (RRFS), and distant metastasis-free survival (DMFS) were 51.8%, 47.3%, 45.6%, and 43.6%, respectively. In both oropharyngeal cancer and nonoropharyngeal cancer patients, in terms of OS, LRFS, RRFS or DMFS no difference was noted regarding primary tumor treatment (CCRT vs. surgery) or neck treatment (CCRT vs. neck dissection). In summary, N3 neck patients treated with definitive CCRT can achieve similar outcomes to those treated with upfront neck dissection followed by adjuvant CCRT. Cautions should be made to avoid overtreatment for this group of patients.

Pain is unpleasant sensory and emotional experience accompanied by tissue injury. Often an indi-vidual experience, it can be influenced by different physiological, psychological, and social factors. Fibromyalgia, one of the most difficult-to-treat types of pain, is characterized by general muscle pain accompanied by obesity, fatigue, sleep, and memory and psychological concerns. Fibromyal-gia has increased nociceptive sensations via central sensitization in the brain and spinal cord level. We used intermittent cold stress to create a mouse fibromyalgia pain model (Day 0: 3.69  0.14 g; Day 5: 2.13  0.12 g). Mechanical pain could be reversed by eicosapentaenoic acid (EPA) admin-istration (Day 0: 3.72  0.14 g; Day 5: 3.69  0.13 g). A similar trend could be also observed for thermal hyperalgesia. The levels of elements in the transient receptor potential V1 (TRPV1) sig-naling pathway were increased in the ascending pain pathway, including the thalamus, medial prefrontal cortex, somatosensory cortex, anterior cingulate cortex, and cerebellum. EPA intake significantly attenuated this overexpression. Novel chemogenetics method was used to indeed in-hibit SSC to ACC activity presented an analgesic effect through TRPV1 downstream pathway. The present results provide insights as to the role of TRPV1 signaling pathway as in fibromyalgia and its potential as a clinical target.

Neuropathic pain is initiated by a malfunction of the somatosensory cortex system. Acupuncture had been shown to have therapeutic effects for neuropathic pain, although with uncertain mechanisms. We used electroacupuncture (EA) to treat mice spared nerve injury (SNI) model and explore the underlying molecular mechanisms through novel chemogenetic techniques. Both me-chanical and thermal pain were found in SNI mice till four weeks (mechanical: 3.23 ± 0.29 g; thermal: 4.9 ± 0.14 s). Hyperalgesia was attenuated by 2 Hz EA (mechanical: 4.05 ± 0.19 g; ther-mal: 6.22 ± 0.26 s) but not with sham EA (mechanical: 3.13 ± 0.23 g; thermal: 4.58 ± 0.37 s), sug-gesting EA’s specificity. In addition, animals with transient receptor potential V1 (Trpv1) deletion showed no significant induction of neuropathic pain (mechanical: 4.43 ± 0.26 g; thermal: 6.24 ± 0.09 s). Moreover, we found increased levels of inflammatory factors such as interleukin-1 beta (IL1-β), IL-3, IL-6, IL-12, IL-17, tumor necrosis factor alpha, and interferon gamma after SNI modeling, which decreased in EA and Trpv1-/- group rather than sham group. Western blot and immunofluorescence analysis showed similar tendency in the dorsal root ganglion, spinal cord dorsal horn, somatosensory cortex (SSC), and anterior cingulate cortex (ACC). In addition, a novel chemogenetics method was used to precisely inhibit SSC to ACC activity showed an analgesic effect through TRPV1 pathway. In summary, our findings indicate a novel mechanism underlying neuropathic pain as beneficial targets for neuropathic pain.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

The so-called “Chinese pyramids” are huge burial mounds covering the tombs of the Emperors of the Western Han dynasty. If we include also the mounds of the members of the royal families, these monuments sum up to more than 40, scattered throughout the western and the southern outskirts of modern Xi'an. They are mostly unexcavated and poorly known although, taken together, they form a fascinating sacred landscape, which was conceived as a perennial witness of one of the most magnificent Chinese dynasties. This sacred landscape is today encroached by the frenetic urban development of the Xi’an urban area. We discuss and elaborate here some of the results of a recent, new satellite-imagery survey of these monuments, highlighting the aspects which may contribute to solutions for a sustainable and compatible development within this important ancient landscape.

Wool quality and yield are important economic traits of livestock. In this study, the skin tissues of the upper scapula of Super Merino sheep (SM) and Small-Tailed Han sheep (STH) during the growing period were studied. Differentially expressed (DE) long non-coding RNAs (lncRNAs) and messenger RNAs (mRNA) were identified via histopathological observation and high-throughput RNA sequencing. Gene ontology (GO) and the Kyoto Encyclopedia of Genes and Genomes (KEGG) were used to analyze differentially expressed genes. Reverse transcription quantitative Polymerase Chain Reaction (RT-qPCR) was used to verify nine selected DE lncRNAs and five DE mRNAs. Significant differences were found in the expression levels of LOC114113396 (KRTAP15-1), CRABP1, KRT10, KRTAP1-3, KRTAP4.3, KRT2, FGF1, IGF-1, and KIT in SM and STH skin tissues. These results indicate that these mRNAs may play an important role in the growth and development of hair follicles and the regulation of hair fiber traits. Differentially expressed lncRNA target genes and mRNAs were mainly enriched in biological processes and pathways related to skin development and fiber traits, which is consistent with previous studies. LncRNA MSTRG.9225.1, MSTRG.124320.1, MSTRG.96951.1, MSTRG.91685.1, MSTRG.122229.1, MSTRG.89255.1, MSTRG.98769.1, and MSTRG.84658.1 may indirectly participate in the growth and development of sheep hair follicles and the regulation of hair fiber diameter by regulating the expression of their respective target genes. These candidate lncRNAs and mRNAs may provide a basis for the study of sheep hair follicle growth and development and hair fiber traits.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

The aim of this paper is to compare the taxonomic composition and species diversity of the macrozoobenthos in Maritsa River (Bulgaria) and Han River (South Korea). Samples were collected at 15 selected sites in each river, including some of their main tributaries in 2020 and 2021. The number of the taxa recorded in Maritsa River was more than twice as great as in Han River: 192 taxa belonging to 19 systematic groups compared to 88 taxa belonging to 18 groups respectively. The order Ephemeroptera had the highest species richness: 31 taxa in the Bulgarian rivers and 26 taxa in the South Korean ones. The macrozoobenthic communities responded and adapted to the various conditions and impacts in the water environment with changes in the species composition and structure. The analysis of the similarity in the taxonomic composition showed low resemblance between all study sites but displayed distinct separations between the rivers and the two years. In general, the species structure of the macrozoobenthic communities in Maritsa River and its studied tributaries was better than in Han River. In both years, high species diversity was recorded at the reference sites in the rivers, characterized by conditions closely resembling natural environments. The species richness and the evenness of macrozoobenthos were very low at sites downstream subjected to considerable anthropogenic pressure. Some of the communities in Han River were almost destroyed completely.

Background: The aim of this study was to investigate the risk of obstructive sleep apnea (OSA) among ankylosing spondylitis (AS) patients in a nationwide population. Methods: We conducted a nationwide cohort study between 2003 and 2013 using the Taiwan National Health Insurance Research Database. The AS cohort included 2210 patients who were newly diagnosed between 2003 and 2013. Randomly selected non-AS controls were matched at a 1:4 ratio based on age, sex and index date. The endpoint of OSA was occurrence or the end of 2013. Cumulative incidences, hazard ratios (HRs) and 95% confidence intervals (CIs) were calculated after adjusting for age, gender, comorbidities and co-medications. Multivariate analyses were performed using Cox proportional hazards model. Due to violation of the proportionality assumption, landmark analysis was conducted to explore the risk of OSA during specific follow-up periods. Results: The adjusted HR (aHR) of OSA for the AS group was 2.826 (95% C.I. = 1.727–4.625) compared to the control group. On landmark analysis, aHR was 7.919 (95% C.I. = 3.169–19.792) for AS group 0–24 months from index date, and decreased to 1.816 (95% C.I. = 0.944–3.494) at ≥ 24 months from index date. On subgroup analyses increased risks of OSA in AS group compared to the control group were found for both males and females (aHRs were 4.533 (95% C.I. = 1.441–14.262) and 2.672 (95% C.I. = 1.522–4.692) for females and males, respectively). On age stratified analysis, there was significant risk only for the 40–59 age group with aHR of 3.913 (95% C.I. = 1.890–8.102). Conclusions: A higher risk of developing OSA was found among newly diagnosed AS cohort during the 12-year follow-up period, especially within 2 years after AS index date and in the 40–59 age group.

Blocking the interaction of the SARS-CoV-2 spike protein with the human angiotensin-converting enzyme II (hACE2) protein serves as a therapeutic strategy for treating COVID-19. Traditional Chinese medicine (TCM) treatments containing bioactive products could alleviate the symptoms of severe COVID-19. However, the emergence of SARS-CoV-2 variants has complicated the process of developing broad-spectrum drugs. As such, the aim in this study was to explore the efficacy of TCM treatments for SARS-CoV-2 variants through targeting the interaction of the viral spike protein with the hACE2 receptor. The antiviral activity was systematically evaluated using a pseudovirus system. Scutellaria baicalensis was found to be effective against SARS-CoV-2 infection through affecting the interaction of viral spike protein with the hACE2 protein. The active molecules of S. baicalensis were identified and analyzed. Baicalein and baicalin, a flavone and a flavone glycoside, respectively, found in S. baicalensis, exhibited strong inhibitory activities, targeting the viral spike protein or hACE2 protein, respectively. Under optimized conditions, virus infection was inhibited by 98% via baicalein-treated pseudovirus and baicalin-treated hACE2. In summary, we identified the potential SARS-CoV-2 inhibitors of the interaction of the Omicron spike protein and hACE2 receptor from S. baicalensis. Future studies on the therapeutic application of baicalein and baicalin against SARS-CoV-2 variants are needed.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Saccharomyces cerevisiae (S. cerevisiae) ethanol fermentation has left an indelible trace in human history. It is regarded as the original beverage synthesis, and has developed into an essential energy supply for mankind today. However, the history of ethanol synthesis using S. cerevisiae, including the mechanism analysis process, has not been carefully and succinctly reported. In this paper, we review the history of ethanol synthesis using S. cerevisiae. In addition, we also review the substrates that drive S. cerevisiae ethanol synthesis, including the utilization of glucose, sucrose, starch and molasses, in order to summarize the current development status and to contribute to the further improvement of this field.

Recently, electrocatalysts for oxygen reduction reactions (ORRs) as well as oxygen evolution reactions (OERs) hinged on electrospun nanofiber composites have attracted wide research attention. Transition metal elements and heteroatomic doping are important methods used to enhance their catalytic performances. Lately, the construction of electrocatalysts based on metal-organic framework (MOF) electrospun nanofibers has become a research hotspot. In this work, bimetallic NixCoy-ZIF nanocrystals were synthesized in an aqueous solution, followed by NixCoy-ZIF/PAN electrospun nanofiber precursors, which were prepared by a simple electrospinning method. Bimetal (Ni-Co) porous carbon nanofiber catalysts doped with nitrogen, oxygen, and sulfur elements were obtained at high-temperature carbonization treatment in different atmospheres (Ar, Air, and H2S), respectively. The morphological properties, structures, and composition were characterized by SEM, TEM, SAED, XRD, and XPS. Also, the specific surface area of materials and their pore size distribution was characterized by BET. Linear sweep voltammetry curves investigated catalyst performances towards oxygen reduction and evolution reactions. Importantly, Ni1Co2-ZIFs/PAN-Ar yielded the best ORR activity, whereas Ni1Co1-ZIFs/PAN-Air exhibited the best OER performance. This work provides significant guidance for the preparation and characterization of multi-doped porous carbon nanofibers carbonized in different atmospheres.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

This study aimed at the investigation of the effect of substrate preheating on residual stress in laser powder bed fusion using a physics-based analytical model. In this study, an analytical model is proposed to predict the residual stress through the calculation of preheating affected temperature profile and thermal stress. The effect of preheating is super-positioned with initial temperature in the modeling of temperature profile using a moving heat source approach; the resultant temperature gradient is then employed to predict the thermal stress from a point body load approach. If the thermal stress exceeds the yield strength of the material, then the residual stress under cyclic heating and cooling will be calculated based on the incremental plasticity and kinematic hardening behavior of metal. IN718 is used as a material example to pursue this investigation. To validate the predicted residual stress, experimental measurements are conducted using X-ray diffraction on IN718 samples manufactured via laser powder bed fusion under different process conditions. Results showed that preheating of the substrate could reduce the residual stress in an additively manufactured part due to the reduction in temperature gradient and resultant shrinkage stresses. However, the excessive preheating could have an opposite impact on residual stress accumulation. Moreover, the results confirm that the proposed model is a valuable tool for the prediction of residual stress- eliminating the costly experiments and time-consuming finite element simulations.

The aim of this study was to examine the prevalence of self-reported and parent-reported bullying victimization, perpetration, and victimization-perpetration and the associations of autistic social impairment and attention-deficit/hyperactivity disorder (ADHD) and oppositional defiant disorder (ODD) symptoms with bullying involvement in adolescents with high functioning autism spectrum disorder (ASD). A total of 219 adolescents with high functioning ASD participated in this study. The associations of sociodemographic characteristics, parent-reported autistic social impairment on the Chinese Social Responsiveness Scale, and parent-reported ADHD and ODD symptoms on the Short form of the Swanson, Nolan, and Pelham Version IV Scale (SNAP-IV)-Chinese version with self-reported and parent-reported bullying victimization, perpetration, and victimization-perpetration evaluated using the Chinese version of the School Bullying Experience Questionnaire were examined using logistic regression analysis. The agreement between self-reported and parent-reported bullying involvement was low. Compared with bullying involvement experiences reported by adolescents themselves, parents reported higher rates of pure bullying victimization (23.7% vs. 17.8%) and victimization-perpetration (28.8% vs. 9.1%) but a lower rate of pure bullying perpetration (5.9% vs. 9.1%). Deficit in socio-communication increases the risk of being pure victims and victim-perpetrators. Parent-reported victim-perpetrators had more severe ODD symptoms than did parent-reported pure victims. The agreement between self-reported and parent-reported bullying involvement of adolescents with high functioning ASD was low. Deficit in socio-communication and ODD symptoms were significantly associated with a high risk of bullying involvement in adolescents with high functioning ASD.

Background and Objective: China has managed to control the coronavirus disease (COVID-19) with confinement measurements and treatment strategies, while other countries are struggling to contain the spread. This study discusses the guidelines related to COVID-19 in China in order to provide important references for other countries in the fight against COVID-19. Methods: Chinese guidelines relevant to COVID-19 were systematically searched via the China National Knowledge Infrastructure database, YiMaiTong database, and World Health Organization (WHO) COVID-19 database on March 20^th, 2020. Guideline information was extracted, including date of publication, source, objectives and the target population. Guidelines specific to the pharmacological treatment of COVID-19 were further investigated to identify the types of antivirus drugs recommended and to report on how treatment recommendations for COVID-19 have evolved overtime. Results: A total of 114 guidelines were identified, of which 87 were national guidelines and 27 were regional guidelines. The scope of included guidelines consisted of: the diagnosis and treatment of COVID-19, the management of hospital departments and specific diseases during the outbreak of COVID-19. Sixty-four of the included guidelines targeted all COVID-19 patients, while the remaining guidelines concentrated on special patient populations (i.e., geriatric population, pediatric population, and pregnant population) or patients with coexisting diseases. Twenty-three guidelines focused on the pharmacological treatments for all COVID-19 patients. Interferon, Lopinavir/Ritonavir, Ribavirin, Chloroquine, and Umifenovir represented the most recommended antivirus drugs. With the emergence of encouraging results from preclinical and preliminary clinical studies, Chloroquine Phosphate was recommended in the national Diagnosis and Treatment Protocol for Novel Coronavirus Pneumonia (6^th version) on February 19^th, 2020. Thereafter, more detailed guidelines regarding the adjustment of dosage regimens and the monitoring of adverse events of Chloroquine Phosphate were published. To date, 8 Chinese guidelines have recommended Chloroquine Phosphate or Hydroxychloroquine as mainstream antivirus drug for the treatment of COVID-19. Conclusions: China has generated a plethora of guidelines covering almost all aspects of COVID-19. Chloroquine, as one widely affordable treatment, holds great potential to become the gold standard choice as more clinical evidence is shared by researchers from China as well as other countries.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

Dissolved organic matter (DOM) derived from organic fertilizers may increase soil phosphorus (P) availability. However, the frequently observed correlation between soil P availability and dissolved organic carbon (DOC) content has led to an excessive focus on DOC content at the expense of DOM properties. The present study investigated the influence of DOM characteristics on soil P availability by using a 6-year field experiment and microcosms of P sorption in paddy soil. Our results showed that partial replacement of chemical P fertilizer with manure or crop straw increased P fertilizer-use efficiency, even when decreasing chemical P input by 34 %, compared to normal chemical fertilization. The microcosm experiment demonstrated that DOM properties, rather than total DOC content, determine soil P sorption capacity, despite the significant correlation between DOC content and P availability observed in the field experiment. Manure-DOM exerted stronger inhibitory effects on P sorption than straw-DOM, and high molecular weight (HMW)-fractionated DOM exerted stronger inhibitory effects on P sorption than low-molecular-weight-fractionated DOM by 16-20%. The mechanism was rooted in the HMW DOM with unique characteristics (e.g., strong aromaticity, hydrophobicity, abundant humic-like components, carboxyl groups, and benzene ring structures) competing for soil P sorption sites (e.g., reduction in specific surface area and micropore volume), decreasing the soil surface charge (e.g., zeta potential), and thereby suppressing P sorption in paddy soil. Our study points out a promising avenue for regulating organic matter properties with organic fertilization to improve P use efficiency in agricultural soils.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Objectives: This study aims to identify, report, and analyze registered and published clinical trials and observational studies for the pharmacological treatment of COVID-19 conducted in China. Methods: A strategic search was conducted via the Chinese Clinical Trial Registry to identify and extract clinical trials and observational studies registered and conducted in China for the pharmacological treatment of COVID-2019 between January 1^st, 2020 and March 21^st, 2020. This was further supplemented by searches conducted via the China National Knowledge Infrastructure (CNKI) database, the MEDLINE database, the World Health Organization (WHO) database, and MedRxiv and BioRxiv electronic platforms for preprint articles, published up until April 8^th, 2020. Studies available in Chinese and English were included in the searches and extracted. A primary descriptive analysis was performed for registered clinical trials and observational studies identified in the Chinese Clinical Trial Registry based on the extraction of the following clinical study information: trial ID, planned date of enrollment, recruitment status, study design, population, sample size, intervention/exposure group, control /reference group, dosage, and primary outcomes. A secondary descriptive analysis was performed for published clinical trials and observational studies identified from the supplementary databases based on the extraction of the following published clinical study information: study design, population, intervention/exposure group, control /reference group and main results as appropriate. Results: A total of 221 clinical trials and observational studies were included from all databases searched. From the Chinese Clinical Trial Registry, 195 registered clinical studies including 170 clinical trials and 25 observational studies were identified and included for primary analysis. From the supplementary databases, 26 published clinical studies including 8 clinical trials and 18 observational studies were included for secondary analysis. Of these 26 published clinical studies, 18 studies, including 3 clinical trials and 15 observational studies were identified from CNKI, 2 studies including 1 clinical trial and 1 observational study from MEDLINE, 2 including 1 clinical trials and 1 observational studies from the WHO database, and 4 including 3 clinical trials and 1 observational studies from MedRxiv and BioRxiv platforms. In the primary analysis, among the 170 clinical trials included from the Chinese Clinical Trial Registry, 101 investigated western medicines (WMs), while 15 investigated Traditional Chinese Medicines (TCMs), and 54 investigated a combination of TCMs and WMs. Among the 25 included observational studies from the Chinese Clinical Trial Registry, 2 investigated WMs, 2 investigated TCMs, and 21 investigated a combination of TCMs and WMs. The total number of exposed patients in all 195 clinical studies from the Chinese Clinical Trial Registry amounted to 24,500. In the secondary analysis, treatment with Lopinavir-ritonavir and treatment with Hydroxychloroquine was not associated with a difference from standard of care in the rate of RT-PCR negativity; treatment with a combination of Lopinavir-ritonavir, interferon α, and Lian-Hua-Qing-Wen capsule was found to significantly improve the effective rate of treatment compared with Interferon α combined with Lian-Hua-Qing-Wen capsule. Conclusions: China is generating a massive source of evidence that is critical for defeating the COVID-19 pandemic. Not only the clinical experience, but also the scientific evidence should be shared with the global scientific community.

Transcription factors (TFs) in the homeodomain-leucine zipper (HD-ZIP) family serve as essential regulators of plant development and control responses to environmental stimuli. To date, however, the HD-ZIP gene family in Prunus nana remains to be fully characterized. Accordingly, a genome-wide analysis of P. nana HD-ZIP family genes was performed using the most recent genomic data available, leading to the classification of 30 HD-ZIP TFs. These genes were annotated and subjected to systematic analyses of phylogenetic relationships, protein physicochemical properties, sequence-based structural characteristics, chromosomal distributions, and associated cis-acting regulatory elements. High levels of diversity were observed with respect to the gene structures for these PnaHD-Zip genes and the cis-regulatory elements found in the promoter regions upstream of these genes, suggesting that they play diverse roles in a range of biological contexts. These 30 PnaHD-Zip genes were further classified into four subgroups based on the results of phylogenetic, gene structure, and conserved motif analyses. Subsequent qPCR analyses indicated that PnaHD-Zip1 and PnaHD-Zip7 expression levels tended to increase was continuously inhibited in response to cold stress, suggesting that proteins in this HD-ZIP gene family may exhibit distinct responses to low-temperature stress exposure. Overall, these results offer a robust foundation for future studies seeking to explore the functional roles that HD-ZIP TFs play as regulators of cold stress tolerance in P. nana, in addition to offering more general insight regarding the regulatory functions and characteristics of these different HD-ZIP genes in P. nana.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

Nasopharyngeal carcinoma (NPC) has not been thoroughly studied, and the pathogenesis of NPC is unclear. Scientists have neither discovered effective therapies nor achieved a desirable prognosis. Some studies have found that the regulation of intra- and extracellular ion channels hinges directly on cell apoptosis, and treatment with Gambogenic acid (GNA) brings changes to the volume-sensitive outwardly rectifying chloride (VSOR Cl-) current of CNE-2Z cells recorded by the patch clamp method. Nevertheless, rarely have any researchers probed into the relevance between this variation and the anti-tumor mechanism of GNA. This paper is suggested that GNA activates the VSOR Cl- current on the CNE-2Z cell membrane, and the activation of VSOR Cl- currents by GNA in CNE-2Z cells is blocked by the chloride channel blockers DIDS and DCPIB. GNA induces the down-regulation of GRP78 and up-regulation of ATF4 as well as chop proteins, which is evidence for the induction of CNE-2Z cell apoptosis, and this correlates with ER stress. GNA can activate the VSOR Cl- channel and lead to the occurrence of ER stress, thus inducing the apoptosis of CNE-2Z cells and inhibiting the proliferation of CNE-2Z cells.

Metal plasmonic nanostructures have promising applications in biosensing due to their ability to facilitate light-matter interaction. However, the damping of the metal leads to a wide full width at half maximum (FWHM) spectrum and results which restricts its sensing capabilities. In this research, we present a novel non-full-metal nanostructure, namely indium-tin oxide (ITO)-Au nanodisk arrays consisting of top ITO nanodisk arrays and a bottom gold layer, and compare the coupling mode with the full-metal nanodisk arrays. The FWHM of proposed ITO-Au nanodisk array reduces to one fifth of that all metal nanodisk arrays, which is generated mode-coupling by surface plasmon modes at metal interfaces with magnetic resonance mode. Furthermore, the thickness variation of nanodisks has no impact on the sensing performance of this ITO-based nanostructure, ensuring excellent tolerance during preparation. We fabricated both structures by using template transfer and vacuum deposition techniques and calibrated their sensing performances by detect Immunoglobulin G (IgG) protein molecules. Both theoretical and experimental results demonstrate that ITO-Au nanodisk arrays provide an effective solution for biosensing applications.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

Ginkgolic acids (GA) have been reported to exhibit anticancer properties, however, the mechanisms remain unclear. This study aims to investigate the mechanisms of GA C13:0 that was isolated from Ginkgo biloba exocarp (GBE) for anti-proliferation, pro-apoptosis and anti-migration effects in human MCF-7 and mouse 4T-1 breast cancer cells. The cytotoxic effect, apoptosis induction and migration inhibition were measured using MTT, TUNEL and Wound healing assays. The expression of mRNA and protein were determined using qPCR and Western blot. Our results showed that no cytotoxicity was found at concentrations of C13:0 below 100µM. The effects of GA C13:0 was further demonstrated by up-regulation of the Bax/Bcl-2 apoptosis pathway and the expression of Apaf-1 protein in the mitochondria. In addition, GA C13:0 also suppressed cell migration and epithelial to mesenchymal transition (EMT) with the increase of E-cadherin expression accompanied by the decrease of Snail, MMP-2, MMP-9 and Vimentin expression. Moreover, GA C13:0 induced cytochrome P450 (CYP) 1B1 expression in aryl hydrocarbon receptor (AhR) pathway. Notably, the up-regulation of CYP1B1 also might play a pivotal regulatory role in mitochondrial and EMT pathways in MCF-7 and 4T-1 cells. Our results may have implications for the development of anticancer agents containing GA as functional additives.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

Hydrogels evolved as an outstanding carrier material for local and controlled drug delivery that tend to the shortcomings of old conventional dosage forms for small drugs (NSAIDS) and large peptides and proteins. Aqueous swellable and crosslinked polymeric network structure of hydrogels is composed of various natural, synthetic and semisynthetic biodegradable polymers. Hydrogels have remarkable properties of functionality, reversibility, sterilizability, and biocompatibility. All these dynamic properties of hydrogels have increased the interest in their use as a carrier for peptides and proteins to be released slowly in a sustained manner. The therapeutical peptide and proteins are remarkable therapeutic agents in today’s world that allows the treatment of severe, chronic and life‐threatening diseases, such as diabetes, rheumatoid arthritis, hepatitis in an easy manner. Despite few limitations, hydrogels provide fine tuning of proteins and peptides delivery with enormous impact in clinical medicine. The primary objective of this article is to review current issues concerned with the therapeutics peptides and proteins and impact of remarkable properties of hydrogels on these therapeutic agents. Different routes for pharmaceutical peptides and proteins and superiority over other drugs candidates are presented. The article will also review literature concerning classification of hydrogels on different basis, polymers used, release mechanisms their physical and chemical characteristics and diverse applications.

Liquid biopsy, based on the circulating tumor cells (CTCs) and cell-free nucleic acids has potential applications at multiple points throughout the natural course of cancer, from diagnosis to follow-up. The advantages of doing ctDNA assessment vs. tissue-based genomic profile are the minimal procedural risk, the possibility to serial testing in order to monitor disease-relapse and response to therapy over time and to reduce hospitalization costs during the entire process. However some critical issues related to ctDNA assays should be taken in consideration. The sensitivity of ctDNA assays depends on the assessment technique and genetic platforms used, on tumor-organ, stage, tumor heterogeneity, tumor clonality. The specificity is usually very high, whereas the concordance with tumor-based biopsy is generally low. In patients with renal cell carcinoma (RCC) qualitative analyses of ctDNA have been performed with interesting results regarding selective pressure from therapy, therapeutic resistance, exceptional treatment response to everolimus and mutations associated with aggressive behavior. Quantitative analyses showed variations of cfDNA levels at different tumor stage. Compared to CTC assay, ctDNA is more stable than cells and easier to isolate. Splice variants, information at single-cell level and functional assays along with proteomics, transcriptomics and metabolomics studies can be performed only in CTCs.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Fracture grouting has been a widely used mitigation measure against seepage in the Yellow River Embankment. However, there is currently a lack of systematic investigation for evaluating the anti-seepage effectiveness of fracture grouting employed in this longest river embankment in China. Therefore, in this work, laboratory and in-situ experiments are carried out for investigating the reinforcement effect of fracture grouting in the Jinan Section of the Yellow River Embankment. In particular, firstly, the laboratory tests concentrate on studying the optimum strength improvement for cement-silicate grout by varying the content of backfilled fly ash and bentonite as admixtures. Flexural strength and Scanning Electron Microscope photographs are investigated for assessing the strength and compactness improvement. Subsequently, based on the obtained optimum admixtures content, in-situ grouting tests are carried out in the Jinan Section of the Yellow River Embankment to evaluate the anti-seepage effectiveness of fracture grouting, where geophysical prospecting and pit prospecting methods are employed. Laboratory results show that, compared with pure cement-silicate grouts, the gelation time of the improved slurry is longer and gelation time increases as fly ash content increases. The optimum mixing proportion of the compound cement-silicate grout is 70% cement, 25% fly ash and 5% bentonite, and the best volume ratio is 2 for the investigated cases. Geophysical prospecting using the Ground Penetrating Radar and High Density Resistivity methods can reflect the anti-seepage effectiveness of fracture grouting on site. It shows that the grouting material mainly flows along the axial direction of the embankment. The treatment that is used to generate directional fracture is proved to be effective. The injection hole interval distance is suggested to be 1.2 m, where the lapping effect of the grouting veins is relatively significant. For the investigated cases, the average thickness of the grouting veins is approximately 6.0 cm and the corresponding permeability coefficient is averagely 1.6 × 10⁻⁶ cm/s, which meets the anti-seepage criterion in practice.

This paper presents the findings of an exploratory study on the continuously generating Big Data on Twitter related to the sharing of information, news, views, opinions, ideas, knowledge, feedback, and experiences about the COVID-19 pandemic, with a specific focus on the Omicron variant, which is the globally dominant variant of SARS-CoV-2 at this time. A total of 12028 tweets about the Omicron variant were studied, and the specific characteristics of tweets that were analyzed include - sentiment, language, source, type, and embedded URLs. The findings of this study are manifold. First, from sentiment analysis, it was observed that 50.5% of tweets had the ‘neutral’ emotion. The other emotions - ‘bad’, ‘good’, ‘terrible’, and ‘great’ were found in 15.6%, 14.0%, 12.5%, and 7.5% of the tweets, respectively. Second, the findings of language interpretation showed that 65.9% of the tweets were posted in English. It was followed by Spanish or Castillian, French, Italian, Japanese, and other languages, which were found in 10.5%, 5.1%, 3.3%, 2.5%, and <2% of the tweets, respectively. Third, the findings from source tracking showed that “Twitter for Android” was associated with 35.2% of tweets. It was followed by “Twitter Web App”, “Twitter for iPhone”, “Twitter for iPad”, “TweetDeck”, and all other sources that accounted for 29.2%, 25.8%, 3.8%, 1.6%, and <1% of the tweets, respectively. Fourth, studying the type of tweets revealed that retweets accounted for 60.8% of the tweets, it was followed by original tweets and replies that accounted for 19.8% and 19.4% of the tweets, respectively. Fifth, in terms of embedded URL analysis, the most common domains embedded in the tweets were found to be twitter.com, which was followed by biorxiv.org, nature.com, wapo.st, nzherald.co.nz, recvprofits.com, science.org, and other URLs. Finally, to support similar research and development in this field centered around the analysis of tweets, we have developed an open-access Twitter dataset that comprises tweets about the SARS-CoV-2 omicron variant since the first detected case of this variant on November 24, 2021.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Natural image matting is an essential technique for image processing that enables various applications, such as image synthesis, video editing, and target tracking. However, the existing image matting methods may fail to produce satisfactory results when computing resources are limited. Sampling-based methods can reduce the dimensionality of the decision space and therefore reduce computational resources by employing different sampling strategies. While these approaches reduce computational consumption, they may miss an optimal pixel pair when the number of available high-quality pixel pairs is limited. To address this shortcoming, we propose a novel multi-criterion sampling strategy that avoids missing high-quality pixel pairs by incorporating multi-range pixel pair sampling and high-quality samples selection method. This strategy is employed to develop a multi-criterion matting algorithm via Gaussian process, which searches for the optimal pixel pair by using the Gaussian process fitting model instead of solving the original pixel pair objective function. Experimental results demonstrate that our proposed algorithm outperforms other methods even with 1% computing resources, and achieves alpha matte results comparable to those yielded by the state-of-the-art optimization algorithms.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

Scaffoldings play a critical role as temporary structures in supporting construction processes. Accidents at construction sites frequently stem from issues related to scaffoldings, including insufficient support caused by deviations from the construction design, insecure rod connections, or absence of cross bracing, which result in uneven loading and potential collapse, leading to casualties. In this study, we introduce a deep-learning-based, augmented reality (AR)-enabled system called scaffolding assembly deficiency detection system (SADDS) to assist field inspectors in identifying deficiencies in scaffolding assemblies. Inspectors have the flexibility to utilize SADDS through various devices, such as video cameras, mobile phones, or AR goggles (i.e., Microsoft HoloLens 2), for automated detection of deficiencies in scaffolding assemblies. The training test yielded satisfactory results, with a mean average precision of 0.89 and individual precision values of 0.96, 0.82, 0.90, and 0.89 for “qualified” frames and frames with the “missing cross-tie rod,” “missing lower-tie rod,” and “missing footboard” deficiencies, respectively. Field tests conducted at two construction sites demonstrated improved system performance compared to that in the training test. However, these field tests also revealed certain limitations of the SADDS system.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

In this paper, the effects of different food-grade enzymes on the antigenicity of casein (CN), β- lactoglobulin (β-LG) and ɑ-lactalbumin (ɑ-LA) in natural cow milk were studied. The degree of hydrolysis (DH), SDS-PAGE and molecular mas (MW) distribution of cow milk (CM) hydrolysates was assessed. Additionally, the residual antigenicity of CM hydrolysates was evaluated by using ELISA and western blotting with anti-CN, anti-β-LG and anti-ɑ-LA rabbit polyclonal antibody. The results showed that Alcalase and Protamex hydrolysis could efficiently reduce the antigenicity of CN, β-LG, ɑ-LA, showed a higher DH and the loss of density of CM proteins, as indicated by SDS-PAGE. The increasing of the low MW (<3 kDa) in CM hydrolysates was also presented. It was also found that Protamex, Alcalase could be more efficiently hydrolyzed major allergenic of CM than other enzymes for the development of hypoallergenic cow milk. Our research will lay a theoretical foundation for the study of hypoallergenic cow milk.

Human epidermal growth factor receptor 2 (HER2), a targetable transmembrane glycoprotein receptor of the epidermal growth factor receptor (EGFR) family, plays a crucial role in cell proliferation, survival, and differentiation. Aberrant HER2 signaling is implicated in various cancers, particularly breast and Gastric cancer, where HER2 overexpression or amplification correlates with aggressive tumor behavior and poor prognosis. Her2 activating mutations contribute to accelerated tumorigenesis and metastasis. This review provides an overview of HER2 biology, signaling pathways, mechanisms of dysregulation, diagnostic approaches, and therapeutic strategies targeting HER2 in cancer. Understanding the intricate details of HER2 regulation is essential for developing effective targeted therapies and improving patient outcomes.

This study analyzes the effect of economic growth and income distribution on health inequality using data from the Organization for Economic Cooperation and Development (OECD). A panel analysis was conducted by combining 21 years of data (from 2000 to 2020) from 38 OECD countries. Life expectancy and avoidable mortality were set as the dependent variables; gross domestic product and poverty gap were set as the independent variables; body mass index, consumption, smoking rate, healthcare personnel, number of beds in health service facilities, national medical expenses, and unemployment were set as control variables. First, economic growth and poverty gap significantly affect life expectancy and avoidable mortality. It has been confirmed that to resolve health inequality, growth during growth and distribution must be prioritized. Second, it has been confirmed that as the poverty gap increases, life expectancy increases and the avoidable mortality rate decreases. A mechanism different from the existence of a medical security system targeting the lowest class or an increase in the welfare of society worked. In conclusion, as a policy proposal to alleviate health inequality, this study suggests that policy intervention is necessary to block or alleviate the negative impact of income inequality in health care policies.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

The pathogenicity of grapevine geminivirus A (GGVA), a recently identified DNA virus, to grapevine plants remains largely unclear. Here, we report a new GGVA isolate (named GGVAQN) obtained from grapevine ‘Queen Nina’ plants with severe disease symptoms; the infectious clone of GGVAQN (pXT-GGVAQN) was also constructed. Infection assays indicated that Nicotiana benthamiana plants inoculated with GGVAQN display upward leaf curling and chlorotic mottling symptoms. Direct injection of Agrobacterium tumefaciens cells carrying pXT-GGVAQN into roots of in vitro-grown ‘Red Globe’ grape plantlets by syringe led to systemic infection with GGVAQN, and the plants exhibited chlorotic mottling symptoms on their upper leaves, and downward curling, interveinal yellowing, and leaf-margin necrosis symptoms on their lower leaves. Our results provide insights into the pathogenicity of GGVA, and a simple and efficient inoculation method to deliver infectious viral clones to woody perennial plants.

Brassica yellows virus (BrYV) is a tentative species of the genus Polerovirus, which occurs widely and mostly damage Brassicaceae plants in East Asia. Since BrYV could not be transmitted mechanically, an insect transmission method is required for further virus research. Here, a reliable and unrestricted method was described, in which non-viruliferous aphids (Myzus persicae) acquired BrYV from transgenic Arabidopsis thaliana plants with virus full length genome germinated from seeds and frozen infected leaves were used to transmit the virus to healthy plants, and there was no significant difference in acquisition rate though transmission rate from frozen infected leaves was somehow lower compared to fresh infected leaves. This novel simple method could be applied to preservation of virus inocula, evaluation of variety resistance to BrYV, biological research on interaction among BrYV, aphid and host, which also provide a new idea on establishing a basic method using virus genomic transgenic plants or frozen infected leaves for other poleroviruses research.

The artificial intelligence (AI) refers to the science and engineering of creating intelligent machines for imitating and expanding human intelligence. Given the ongoing evolution of the multidisciplinary integration trend in modern medicine, numerous studies have investigated the power of AI to address orthopaedic-specific problems. One particular area of investigation focuses on the shoulder pathology, which is a range of disorders or abnormalities of shoulder joint, causing pain, inflammation, stiffness, weakness, and reduced range of motion. There has not yet been a comprehensive review of the recent advancements in this field. Therefore, the purpose of this review is to evaluate the current AI applications in the shoulder pathology. This review mainly summarizes several crucial stages of the clinical practice, including predictive models and prognosis, diagnosis, treatment, and physical therapy. In addition, the challenges and future development of AI are also discussed.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Background: Accurate prediction of patients’ response to therapy is clinically indispensable, howbeit challenging. With increased understanding of the human genome and malignancies, there is the renaissance of in silico pharmacogenomics with renewed interest in drug response predictability based on gene-drug interaction. Objective: Evidence-based transcript-proteome profiling is essential for synthesizing clinically applicable algorithms for predicting response to anticancer therapy, including immune checkpoint blockade (ICBT); thus, saving physicians’ time, reducing polypharmacy, and curtailing unnecessary treatment expense. In this study, we tested and validated the hypothesis that a selected proteomic signature in ICBT-naïve patients is sufficient for the prediction of response to ICBT. Methods: Using a multimodal approach consisting of computational pharmacogenomics, transcript-proteome analytics, mathematical modeling, and machine learning systems; we delineated therapy-sensitivity and stratified patients into graduated response groups based on their proteomic profile. Protein expression levels in our cohort tissue specimens were evaluated based on T cell- and non-T cell- inflamed phenotypes by immunohistochemistry. Results: We established β-catenin, PDL1, CD3 and CD8 expression-based ICBT response model. Statistical regression models validated the predictive association between our predefined algorithms and therapeutic outcome. Interestingly, our 4-gene prediction classifier was constitutively independent of tumor tissue origin, correctly stratified patients into high-, low-, and non- responders pre-treatment, with high prediction accuracy, and exhibited good association with patients’ performance status and prognosis (p < 0.01). Conclusion: Our findings demonstrate the possibility of accurate proteomics based ICBT response prediction and provide a putative basis for drug response prediction based on selective proteome profile in untreated cancer patients.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.