The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

The NCO functional group of 3-isocyanatoproply triethoxysilane (IPTS) and the OH functional group of DOPO-BQ were used to conduct an addition reaction. Following completion of the reaction, triglycidyl isocyanurate (TGIC) was introduced to conduct a ring-opening reaction. Subsequently, a sol-gel method was used to take place a hydrolysis- condensation reaction on TGIC-IPTS-DOPO-BQ to form a hyperbranched nitrogen–phosphorous–silicon (HBNPSi) flame retardant. This flame retardant was incorporated into a polyurethane (PU) matrix to prepare a hybrid material. Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), limiting oxygen index (LOI), UV-VIS spectrophotometry, and Raman analysis were conducted to structure characterization and analyzed transparency, thermal stability, flame retardancy, and residual char to understand the flame retardant mechanism of prepared hybrid materials. After the flame retardant was added, the maximum degradation rate decreased from −36 wt%/min to −17 wt%/min, the integral procedure decomposition temperature (IPDT) increased from 348 ℃ to 488 ℃, and the char yield increased from 0.7 to 8.1 wt%. The aforementioned results verified that thermal stability of PU can be improved after adding HBNPSi. The LOI analysis indicated that the pristine PU was flammable because the LOI of pristine PU was only 19. When the content of added HBNPSi was 40%, the LOI value was 26; thus the PU hybrid became nonflammable.

Patients with lean NAFLD make up an increasing subset of liver diseases. The association between lean NAFLD and feutin-A, which serves as a hepatokine and adipokine, has never been examined. Our study aimed to explore the association of serum fetuin-A among lean and nonlean patients. The study comprised 606 adults from the community, stratified into lean or nonlean (BMI </≥ 24 kg/m2) and NAFLD or non-NAFLD (scoring of ultrasonographic fatty liver indicator, US-FLI ≥ 2/<2). Multivariate logistic regression analyses were performed to estimate the odds ratio of having NAFLD among the tertiles of fetuin-A after adjustment. The least square means were computed by general linear models to estimate marginal means of the serum fetuin-A concentrations in relation to the NAFLD groups. The OR of having NAFLD for the highest versus the lowest tertile of fetuin-A was 2.62 (95% CI: 1.72-3.98; P for trend<0.001). Stratifying by BMI, the OR of having lean NAFLD for the highest versus the lowest tertile of fetuin-A was 2.09 (95% CI: 1.09-3.98; P for trend 0.026), while nonlean NAFLD had no significant association with the fetuin-A gradient after adjustments. Fetuin-A was positively associated with lean NAFLD after adjusting for central obesity and insulin resistance.

This study used the sol–gel method to synthesize a non-halogenated hyperbranched flame retardant containing nitrogen, phosphorus and silicon, HBNPSi, which was then added to a polyurethane (PU) matrix to form an organic–inorganic hybrid material. Using 29Si nuclear magnetic resonance, energy-dispersive X-ray spectroscopy of P- and Si-mapping, scanning electron microscopy, and X-ray photoelectron spectroscopy, this study determined the organic and inorganic dispersity, morphology, and flame retardance mechanism of the hybrid material. The condensation density of the hybrid material PU/HBNPSi was found to be 74.4%. High condensation density indicates a dense network structure of the material. The P- and Si-mapping showed that adding inorganic additives in quantities of either 20% or 40% results in homogeneous dispersion of the inorganic fillers in the polymer matrix without agglomeration, indicating that the organic and inorganic phases had excellent compatibility. In the burning test, adding HBNPSi to PU resulted in the material passing the UL-94 standard at the V2 level, unlike the pristine PU, which did not meet the standard. The results demonstrated that after non-halogenated flame retardant was added to PU, the material’s flammability and dripping were lower, thereby proving that flame retardants containing elements such as nitrogen, phosphorus, and silicon exert an excellent flame retardant synergistic effect.

This paper designs and fabricates a small-type permanent-magnet linear motor and driver for automation applications. It covers structural design, magnetic circuit analysis, control strategies, and hardware development. Magnetic circuit analysis software JMAG is used for flux density distribution, back electromotive force(back-EMF), and electromagnetic force analysis. To address end effects and cogging force, auxiliary core structures and control strategies are proposed. The motor has a three-phase, six-coil, seven-pole configuration, achieving a peak phase voltage of 3.621 V at 1.0 m/s with a total harmonic distortion(THD) of 0.49 % and the voltages of each phase are balancing a phase voltage error of -0.002 V. The average electromagnetic force is 5.46 N/A. The driver uses a three-phase inverter with voltage space vector pulse width modulation(VSVPWM), dq-axes current closed-loop control, electromagnetic force control, and S-curve motion trajectory control. Simulations with JMAG-RT models in MATLAB/Simulink verify the control strategies. A microcontroller (TMS320F280045) serves as the control core, and a magnetic encoder with a 488 nm resolution provides position feedback. Each phase winding has an equivalent resistance of approximately 3.0 Ω and an inductance of approximately 1.98 mH. The S-curve motion trajectory control achieves a maximum position error of approximately 5.0 μm and a speed ripple of approximately 0.03 m/s at steady speed. With cogging force improvement, the maximum electromagnetic force is 4.90 N, and the q-axis current compensates around 1.05 A based on mover position. S-curve motion trajectory control results in highly stable and responsive performance. Practical tests show that the designed small-type permanent-magnet linear motor and its driver provide efficient, stable, and high-precision solutions for automation applications.

In this study, a composite flame retardant was created by combining fish scale (FS), fishery waste, and ammonium polyphosphate (APP), a commercially available flame retardant. The composite flame retardant was added to epoxy resin (EP) to form an EP/APP/FS composite that prevents burns and is environmentally friendly. The use of FS conforms to the concept of circular economy and lowers costs by reducing the consumption of APP. Thermogravimetric analysis (TGA), integral procedural decomposition temperature (IPDT), pyrolysis kinetics, limiting oxygen index (LOI), the Underwriters Laboratories 94 (UL94) flammability test, scanning election microscopy, Raman spectroscopy, and energy-dispersive X-ray spectroscopy were used to determine the thermal properties, flame retardant properties, flame retardant mechanism, char morphology, and composition of the composites. The TGA results indicated that the addition of 40% flame retardant raised the char residue from 16.45 wt% (pure EP) to 36.07 wt%, IPDT from 685.6 °C (pure EP) to 1143.1°C, LOI from 21% (pure EP) to 30%, and UL94 classification from fail (pure EP) to V-0. These results suggest an increase in char residue, which indicates better protection of the polymer matrix material. The improvements in IPDT, LOI, and UL94 classification, which indicate greater thermal stability, lower flammability (from flammable to fireproof), and higher flammability rating (from fail to V-0), respectively, suggest that the composite material has favorable thermal properties and is less inflammable.

(1) Background: Parents of children with autism spectrum disorders often experience psychological distress, which can affect the quality of childcare they provide. It is crucial to screen for psychiatric symptoms among these parents. The Core Symptom Index (CSI) is a widely used tool for assessing general symptoms such as depression, anxiety, and somatic symptoms, with demonstrated validity and reliability across various populations. However, there is limited research on the validity and reliability of the CSI in the general Chinese population. This study aimed to investigate the psychometric properties of the Chinese version of the CSI among parents of children with autism spectrum disorders using Confirmatory Factor Analysis (CFA). (2) Methods: A total of 794 Chinese parents raising children with autism participated in this study. All completed the CSI, along with the social inhibition subscale of the Interpersonal Problems Inventory and the Couple Satisfaction Index. Factorial validity was assessed using CFA to determine how well the bifactor three-factor model fits the data. Various structural models were compared using model fit indices. Convergent and discriminant validity were examined by exploring correlations with the social inhibition subscale and the Couple Satisfaction Index. Invariance testing of the CSI was conducted across multiple groups based on gender, age, and education using CFA. The reliability of the CSI was evaluated using McDonald’s omega coefficients. (3) Results: The bifactor model emerged as the best-fitting model for the data, suggesting that the total score of the CSI adequately represents overall psychiatric symptoms. The CSI exhibited significant correlations with the social inhibition subscale (r = 0.41, p &lt; 0.01) and smaller correlation coefficients with the Couple Satisfaction Index (r = -0.16, p &lt; 0.05), indicating both convergent and discriminant validity. Invariant tests supported scalar invariance levels based on gender and age but only partial invariance for education. The Chinese version of the CSI demonstrated high consistency, with McDonald's omega coefficients ranging between 0.86 and 0.95. (4) Conclusions: The bifactor model of the Chinese version of the CSI is validated, making it a suitable tool for measuring depression, anxiety, and somatization symptoms among parents of children with autism spectrum disorders. Further research on other Chinese populations is encouraged.

Zinc cobalt oxide-zinc hydroxide (ZnCo2O4-Zn(OH)2) microspheres were successfully fabricated on carbon cloth via a sample hydrothermal method. The surface morphology of these microspheres and their efficacy in degrading methyl violet were further modulated by varying the thermal annealing temperatures. The manipulation of thermal annealing temperatures was pivotal in adjusting the porosity of ZnCo2O4-Zn(OH)2 microspheres to amplify their photocatalytic performance. Various analytical techniques were utilized to evaluate the physical and chemical properties of the ZnCo2O4-Zn(OH)2 microspheres, including field-emission scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, field-emission transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis spectroscopy. Compared to untreated ZnCo2O4-Zn(OH)2 microspheres, those subjected to thermal annealing exhibited increased specific surface area and light absorption capacity, rendering them highly effective photocatalysts under UVC light exposure. Subsequent studies have confirmed the superior performance of ZnCo2O4-Zn(OH)2 microspheres as a reusable photocatalyst for degrading methyl violet and tetracycline. Additionally, trapping experiments during the photodegradation process involving ZnCo2O4-Zn(OH)2 microspheres have identified hydroxyl radicals (·OH) and superoxide radicals (·O2–) as the primary reactive species.

In this study, we demonstrate a high luminous efficacy of 118 lm/W and high reliability through 450°C thermal aging of white LEDs (WLEDs) utilizing four-inch YAG: Ce3+ phosphor-in-glass (PiG) plates designed for vehicle headlights. The sintering process of mixing glass and phosphor typically generates pores, which can scatter light and reduce the luminous efficacy of the fabricated PiG. In this study, we produced four-inch PiG plates under four different fabrication conditions to evaluate their luminous efficacy. Our results revealed that the PiG plate with a thin thickness of 0.08 mm exhibited a 16.83% increase in luminous efficacy compared to the 0.15 mm plate, attributed to reduced light interaction with the pores. Unlike silicone-based phosphor WLEDs, which offer high performance but lower reliability due to the silicone resin's low transition temperature (150°C), our novel thin PiG plate achieves high performance and reliability. This advancement suggests that the proposed thin PiG plate could replace traditional silicone-based phosphors, enabling the development of high-quality WLEDs for vehicle headlights in automotive applications.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

Vaccination represents the historical milestone in medical sciences, which has been saving millions of lives. Nonetheless, continued outbreaks of emergent infectious diseases are swamping from every coast to every border all over the world. Modern vaccines are our most powerful arsenals to defend the public health of a global population ever since 1796. As unexpected, modern vaccination approaches have brought out all sorts of unwelcome pathogenic disorders to varying extents. Pathogenic viruses have also continued to evolve to defeat elaborate arsenals devised by human intelligence. In this review, we have covered a variety of vaccination approaches along with their sophisticated materials from the past to the most recent development. Furthermore, we discuss varied serious pathogenic outcomes elicited by contemporary vaccination programmes involving novel materials in real clinical trials. The complex immune mediators will be discussed in the context to tackle the complication of vaccine-induced pathogenesis. We will offer the insight into the intractable discrepancy of vaccine-associated pathology. The precision approach bestowed with evolutionary concepts will be considered as a feasible option to confront various issues of pathogenic complicacy.

Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Litsea martabanica root's antioxidant and AChE activity showed promise as a pesticide detoxification agent in our previous study. In addition to roots, its leaves can help mitigate pesticide exposure, although there is limited scientific evidence supporting their efficacy. However, the use of roots in many countries, such as Thailand, could contribute to environmental degradation, as highland communities traditionally cut down whole trees to obtain them. This study aims to evaluate the antioxidant activity and anti-pesticide potential of water extracts from L. martabanica leaves instead of its roots through in vitro and in vivo investigations. The findings showed that L. martabanica water extracts and fractions demonstrated varied antioxidant activity. The water extract, obtained using traditional extraction methods, was chosen for in vivo experiments. Rats received the extract followed by chlorpyrifos exposure for 16 days. Results indicated reduced acetylcholinesterase activity in chlorpyrifos-exposed rats, while treatment with leaf extract led to increased activity, suggesting its potential as a detoxifying agent. Histopathological examination revealed no liver cell necrosis and showed liver cell regeneration, indicating potential protection against free radical-induced liver damage without affecting rat liver weight or biochemical profiles. Utilizing L. martabanica leaves for healthcare purposes holds promise without negative environmental impact.

In the extended malfatti problem, the numbers of circles in the triangle are triangle numbers, because the tangency properties among the internal circles and 3 sides of the triangle have special type of structure. That is, the corner circle tangent to two sides of the triangle and two boundary circles, the boundary circles tangent to one side of the triangle and 4 other circles, and the inner circles always tangent to 6 other circles. The circles we find in extended general Malfatti’s problem has the property that the smallest radius and the largest radius for the circle has big difference. In this paper, we proposed algorithms to solve the problem that the tangency properties among circles and sides of triangle is not fixed, so that the number of circles in the triangle is not necessary a triangle numbers. The purpose of this change is try to find the radii of the circles in the triangle is within a small range.

Background and Objectives: Although researchers suggested that non-pharmaceutical intervention (NPI) and vaccination together can provide the best protection from the COVID-19 [1], people’s willingness to adopt personal NPIs seems to decrease through the COVID-19 waves. This study seeks for an explanation for this observation based on the framework of risk perception. Materials and Methods: Two cross-sectional surveys (N = 407 in Survey 1 and N = 505 in Survey 2) were administered before and in the first outbreak of COVID-19 in Taiwan. The survey items were designed to measure people’s recognized severity of COVID-19, worry of COVID-19, intention to adopt personal NPIs, and attitude toward COVID-19 vaccines. We established a structural model according to the framework of risk perception, which was applied to fit the data of the two surveys. Results: The multigroup SEM (Structural Equation Modeling) results showed that worry (i.e., emotional component of risk perception) fully mediates the influence of recognized severity of COVID-19 (cognitive component of risk perception) on the intention to adopt NPIs in each survey. Before the outbreak (i.e., Survey 1), people’s attitude toward COVID-19 vaccines has nothing to do with their worry of COVID-19. However, when people have experienced the real outbreak of COVID-d19 (i.e., Survey 2), their attitude toward COVID-19 vaccines negatively predicts their worry of COVID-19, forming an indirectly negative effect on their intention to adopt personal NPIs, suggesting the occurrence of the Peltzman effect. That is, receiving vaccination makes people feel safer, that the other way around relaxes their alert for COVID-19, thus, declining the intention to adopt personal NPIs.

Limited understanding exists regarding the intricate dynamics between the levels of social inhi-bition exhibited by both wives and husbands concerning their perceived family support and de-pressive symptoms, particularly within couples who are parents of children diagnosed with au-tism spectrum disorder (ASD). This study used the actor-partner, interdependence mediation model to analyze data collected from 397 pairs of Chinese parents with children diagnosed with ASD. The findings of the study revealed significant indirect actor effects, indicating that the levels of social inhibition exhibited by both wives and husbands were associated with their own de-pressive symptoms through their respective perceptions of family support. In general, the study did not find significant partner effects, except for some indirect effect (IE) of wives on their hus-bands' depressive symptoms through the wives' perceived social support. This observation sug-gests that cultural norms and role expectations within the family context may influence these dy-namics. These results underscore the potential importance of interventions aimed at addressing social inhibition and enhancing perceived family support to alleviate depressive symptoms in this population. Additionally, interventions targeting fathers should emphasize the importance of their involvement in parenting and collaboration with their partners in caring for children with ASD. Such collaborative efforts may contribute to improved outcomes for both parents and chil-dren within families affected by ASD.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

In China, preschool teachers have a significant influence on the development of young children aged 3-6. It is imperative to understand their mental health and the factors associated with it to inform policies, optimize their mental well-being, and support their job performance. This study aimed to investigate the factors contributing to anxiety symptoms among preschool teachers. A sample of 393 Chinese preschool teachers (279 females, 114 males) aged 21-56 completed online questionnaires collecting their socio-demographic and work-related information and assessing anxiety symptoms, interpersonal difficulties, personality traits, perceived stress, resilience, and inner strength. Pearson correlation and multiple linear regression analyses identified significant predictors of anxiety symptoms. The prevalence of anxiety symptoms among the studied cohort was found to be 12.2%. Statistically significant factors positively correlated with anxiety symptoms included objective work-related stress (B=0.149, p<.001), interpersonal difficulties (B=0.921, p<.001), perceived stress (B=0.108, p=.001), and neuroticism (B=0.071, p=.002). The findings highlight the urgent need for measures to reduce work-related stress and anxiety. However, when negative mental health predictors were included, the effect of positive psychological factors became nullified. Positive mental health might have a moderating role in such a negative mental health outcome as anxiety. Therefore, further research is required to understand the impact of positive mental health factors more clearly.

Background: Echovirus 11 (EV-11) is a notable enterovirus linked to severe infections in neonates, often resulting in significant morbidity and mortality. In April 2019, an EV-11 outbreak occurred in the sick neonate room at a teaching hospital in Taichung, Taiwan, posing a serious threat to the vulnerable infants in this setting. Objectives: This study aimed to identify the source and transmission dynamics of the EV-11 outbreak in the neonatal unit and evaluate the effectiveness of the infection control measures implemented to contain the outbreak. Methods: Patient records, epidemiological data, and laboratory findings were reviewed. For all cases, confirmatory tests were performed using virus isolated from cerebrospinal fluid. Rapid quarantine measures were employed. The hospital’s nosocomial infection surveillance system was used to track confirmed cases and exposed individuals to facilitate effective management and monitoring; Results: Five neonates were confirmed to have EV-11 during the outbreak. Surveillance of 10 contacts and 11 newly admitted cases yielded negative results. All infected infants eventually recovered. The cohort comprised three males and two females, with a birth weight range of 2472–4224 grams. Their gestational ages range of 34 3/7 weeks to 39 weeks; including two premature and three full-term infants. Symptoms began between 6 and 27 days of life, with fever being the consistent clinical manifestation. Strict infection control measures, including isolation of infected cases, suspension of rooming-in, and rigorous disinfection protocols, successfully halted viral spread. The outbreak was contained within 39 days, with no additional cases reported post-intervention; Conclusions: The prompt and effective response, including robust infection control protocols, was crucial for managing and containing the EV-11 outbreak in the neonatal unit. These cases underscore the significance of immediate action, stringent infection control measures, and ongoing monitoring for addressing enterovirus outbreaks in neonatal care settings.

(1) Background: Proximal humerus fractures can be a debilitating condition if not properly treated. These fracture patterns are varied and differ in every patient. Functional outcomes may be determined by the integrity of the shoulder girdle involving the rotator cuff insertion. The post-operative resorption or malreduction of the greater tuberosity is an important factor contributing to the poor functional outcome of a patient. (2) Methods: A single-center retrospective comparative study was performed to evaluate the functional outcomes of patients undergoing operative fixation for this injury. A total of 387 consecutive cases treated operatively from 2019-2021 were included for analysis. (3) Results: 94 cases fulfilled our criteria for analysis. A matched-group comparison of 19 patients each was performed to compare demographics, post-operative fracture characteristics and functional outcomes. (4) Conclusions: The resorption or malreduction of the greater tuberosity contributes greatly to the prognostic outcome in patients treated with ORIF surgery. In our demographic study, obesity is another contributing factor affecting the parameters of post-operative reduction in proximal humerus fractures. Appropriate surgical planning and post-operative multidisciplinary care must be taken into consideration to attain a satisfactory prognostic outcome.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

Stallion mules have been used as working equids in several countries. Aggressiveness, under the influence of testosterone, resulted in the necessity for surgical castration before work training. The gonadotropin-releasing hormone (GnRH) vaccine may be an alternative method for immunocastration in mules. The objectives were to evaluate the effect of GnRH vaccine on anti-GnRH antibody production, serum testosterone level, clinical adverse effects, and behavior toward human manipulation. Twenty-five mules were separated into 3 groups: Control-intact, Control-castrated, and Treatment. Treatment was further divided into subgroups according to condition (intact or unilateral cryptorchid) and age. Treatment received 195 µg GnRH vaccine intramuscularly at week 0, 4, and 8. Anti-GnRH antibody increased at week 6 and 10, then gradually decreased to baseline at week 22. Treatment-intact-young had the highest anti-GnRH antibody, resulting in lower serum testosterone levels during week 2-6 and 12-16 compared to Control-intact. Subcutaneous edema adjacent to the injection site was detected only in Treatment-intact after booster vaccination. During week 6-22, the behavioral scores of Treatment significantly changed toward at ease with human contact compared to a score before vaccination. In conclusion, mules responded to GnRH vaccine, which could temporarily suppress testosterone for up to 16 weeks.

Cancer patients, susceptible to severe COVID-19 outcomes, exhibit varied vaccine responses, particularly those who are receiving chemotherapy. This prospective cohort study enrolled 115 cancer patients, and data from 91 patients who received two doses of COVID-19 vaccines were analyzed. Blood was drawn at baseline, day 28, and 6 months post-second dose for neutralizing antibody analysis. The primary outcome was seroconversion rate against wild type and Omicron at day 28. Secondary outcomes included seroconversion at 6 months, factors associated with seroconversion, and safety. Of the 157 cancer patients screened, 91 were enrolled, with 45% receiving chemotherapy. Seroconversion rates at day 28 were 77% for the wild type and 62% for Omicron. Chemotherapy did not affect seroconversion (p=0.789 for wild type, p=0.597 for Omicron). Vaccine type positively correlated with seroconversion, with an adjusted ORR of 25.86 (p=0.029) for the wild type and 17.38 (p<0.001) for Omicron with the primary heterologous vaccine. Adverse events were grade 1 in 34.0% and grade 2 in 19.7% of participants. Despite lower seroconversion against Omicron, no difference was noted between chemotherapy and non-chemotherapy groups. COVID-19 vaccinations demonstrated good tolerability. This data underscores vaccine efficacy considerations in cancer patients, informing tailored strategies for this vulnerable population.

With the advances in industry and commerce, passengers have become more accepting of environmental sustainability issues; thus, more people now choose to travel by bus. Government administration constitutes an important part of bus transportation services as the government gives the right-of-way to transportation companies allowing them to provide services. When these services are of poor quality, passengers may lodge complaints. The increase in consumer awareness and developments in wireless communication technologies have made it possible for passengers to easily and immediately submit complaints about transportation companies to government institutions, which has brought drastic changes to the supply-demand chain comprised of the public sector, transportation companies, and passengers. This study proposed the use of big data analysis technology including systematized case assignment and data visualization to improve management processes in the public sector and optimize customer complaint services. Taichung City, Taiwan was selected as the research area. There, the customer complaint management process in public sector was improved, effectively solving such issues as station-skipping, allowing the public sector to fully grasp the service level of transportation companies, improving the sustainability of bus operations, and supporting the sustainable development of the public sector-transportation company-passenger supply chain.

Ultramafic rocks become promising candidates for carbon sequestration by enhanced carbon dioxide (CO2) mineralization strategies due to their highly CO2-reactive mineral composition and its abundant availability. This study reports a mineralogy and microtextures of a representative ultramafic rock from the Ma-Hin Creek in northern Thailand and observes evidence of CO2 mineralization occurring through the interaction between CO2 and the rock with the existence of water under ambient conditions. After sample collection, rock description was determined by optical petrographic analysis. The rock petrography reveals a cumulated wehrlite comprising over 50% olivine and minor amounts of clinopyroxene, plagioclase, and chromian spinel. Approximately 25% of the wehrlite has altered to serpentine and chlorite. A series of CO2 batch experiments were conducted on six different rock sizes at a temperature of 40°C and pressure of 1 atm over five consecutive days. The post-experimental products were dried, weighed, and geochemically analyzed to detect changes in mineral species. Experimental results showed that product weight and the presence of calcite increased with reducing grain size. Additionally, the modal mineralogy of the wehrlite theoretically suggests a potential CO2 uptake of up to 53%, which is higher than the average uptake values of mafic rocks. These findings support the suitable rock investigation approach and the preliminary assessment of carbon mineralization potential, contributing to enhanced rock weathering techniques for CO2 removal that could be adopted by mining and rock supplier industries.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Mistreatment can adversely affect students’ academic performance and mental health. This study aimed to investigate the prevalence of mistreatment and its association with academic motivation among Thai medical students in clinical years. A cross-sectional study was conducted among medical students throughout Thailand using the Composite Questionnaire of Mistreatment and Academic Motivation Scale (AMS). Descriptive statistics, chi-square tests, correlations, and regression analyses were conducted. A p-value &lt; 0.05 was considered statistically significant. The sample included 399 students, with mean age of 23 ± 1.29 years old, and 61.5% were female. A total of 81% of participants experienced mistreatment. Twenty-nine percents of students thought that mistreatment occurred because the maltreaters did not consider mistreatment as inappropriate or serious. Students who experienced mistreatment exhibited lower AMS (B = -9.16, 95% CI: -15.37 to -2.95, p-value = 0.004) than those who did not. Moreover, students who experienced academic mistreatment exhibited a higher amotivation score (B = 1.50, 95% CI: 0.16 to 2.85, p-value = 0.029) than those who did not. The prevalence of mistreatment was unexpectedly high, and it associated with students' motivation to study. Educational institutions should prioritize addressing this issue and developing strategies to provide assistance, including the enhancement of reporting systems.

In recent years, growing attention has been directed towards the potential of plant extracts as great therapeutic agents in controlling oxidative stress and inflammation. Gymnema inodorum (Lour.) Decne, an indigenous plant locally grown in Northern Thailand, is known for its anti-diabetic activity. This study aims to explore the antioxidant properties and phenolic profile of column chromatographic fractionated G. inodorum leaf extract. The ethanolic-reflux extracts of G. inodorum leaves were subjected to column chromatography for the isolation of bioactive molecules. Total phenolic and flavonoid content were assessed using Folin–Ciocalteu and aluminium chloride colorimetric methods, respectively. Total antioxidant activity was evaluated by employing different antioxidant assays, including 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulfonic)acid (ABTS) scavenging assay and ferric reducing antioxidant power (FRAP) assay. High-Performance Liquid Chromatography (HPLC) with a C18 column was employed to determine the level of gymnemic acid, while Liquid Chromatography Quadrupole Time-of-Flight/Mass Spectrometry (LC-QTOF/MS) was used to identify potential phenolic compounds. The three separated fractions indicating A, B, and C, exhibited remarkable antioxidant activity, with total phenolic content of 0.294 ± 0.056, 0.085 ± 0.039, and 0.227 ± 0.041 mg QE/mL, and total flavonoid content of 0.274 ± 0.050, 0.309 ± 0.110, and 0.384 ± 0.007 mg QE/mL, respectively. Fraction A exhibited the highest DPPH and ABTS scavenging activity, while fraction C demonstrated significantly higher ferric-reducing power. HPLC analysis revealed a highest concentration of gymnemic acid in fraction C (0.393 ± 0.003 mg/g) compared to fraction A (0.159 ± 0.003 mg/g) and fraction B (0.142 ± 0.000 mg/g). The LC-QTOF/MS phenolic screening showed seven potential phenolic compounds in fraction A, seven compounds in fraction B, and four compounds in Fraction C. A significant relationship is found between antioxidant potential and total phenolic content, suggesting that phenolic compounds are the major contributors to the antioxidant activity of G. inodorum.

This research focuses on optimization of coupled solar production and battery storage system to achieve Nearly Zero-Energy Building (nZEBs) based on building load behavior patterns. Moni-toring data from an office building with 120kW peak and 40kW average load consumption equipped with a 160kW solar photovoltaic (PV) system and a 50kW-45kWh energy storage system (ESS). The primary objective is to the primary objective is to analyze collected data from existing system and setup guideline to optimize ESS capacity to maximize clean energy consumption and thus minimize excess production losses, progressing the building toward Nearly ZEB Level 1 status (87.5%-100% energy usage). The study outcome has identified parameter impacts and demonstrates additional optimized cases with various PV and ESS installed capacity. Further analysis is performed based on working day load profile and appliance patterns. This ap-proach aims to learn the usage HVAC, lighting, and electronics, enabling the optimization scheme to be applied to buildings with different load patterns. Additionally, the analysis predicts other building behavior patterns and optimized clean energy system. The findings are then validated against actual data and the results demonstrate good model accuracy, especially daytime predic-tion. These insights also provide guidelines and strategies for further interventions on HVAC operations and adjusting concerned schedules to achieve desired ZEB level.

Wearable assistant devices play an important role in daily life for people with disabilities. Those who are hearing impaired may face dangers while walking or driving on the road. The major danger is their inability to hear warning sounds from cars or ambulances. Thus, the goal of this study is to develop a wearable assistant device for the hearing impaired to recognize emergency vehicle sirens on the road using edge computing. An EfficientNet-based fuzzy rank-based ensemble model was proposed to classify seven audio sounds, including human vocalizations and emergency vehicle sirens. This model was embedded in an Arduino Nano 33 BLE Sense development board. The audio files were respectively obtained from the CREMA-D dataset and Large Scale Audio dataset of emergency vehicle sirens on the road, with a total number of 8756 files. The seven audio sounds included neutral vocalization, anger vocalization, fear vocalization, happy vocalization, car horn sound, siren sound, and ambulance siren sound. The audio signal was converted into a spectrogram by the short-time Fourier transform as the feature. When one of the car horns, sirens, or ambulance sirens was detected, the wearable assistant device presented alarms through vibration and messages on the OLED panel. The performances of the EfficientNet-based fuzzy rank-based ensemble model in offline computing achieved an accuracy of 97.1%, precision of 97.79%, sensitivity of 96.8%, and specificity of 97.04%. In edge computing, the results were an accuracy of 95.2%, precision of 93.2%, sensitivity of 95.3%, and specificity of 95.1%. Thus, the proposed wearable assistant device has the potential benefit of helping the hearing impaired avoid traffic accidents.

Background Coronary artery disease (CAD) is a widely recognized cardiovascular disease that is considered the leading cause of death worldwide, affecting people on a global scale. Percutaneous coronary intervention (PCI), which involves procedures such as balloon angioplasty or stenting, plays an important role in opening blocked arteries and minimizing damage to the cardiac muscle. While the use of drug-eluting stents (DESs) has significantly reduced the occurrence of coronary restenosis, the problem of in-stent restenosis (ISR) continues to pose a significant clinical challenge. Gaining a deeper understanding of the clinical predictors associated with ISR is vital for early detection and appropriate treatment. Hence, this study aimed to evaluate the clinical predictors of ISR specifically in Taiwanese patients. Methods We conducted a single-center, retrospective case-control study, enrolling 517 CAD patients undergoing previous coronary stenting and stable angina with positive stress test or acute coronary syndrome (ACS) during follow-up between January 2019 and December 2022 at National Taiwan University Hospital. The patients were categorized into two groups: the ISR group, consisting of individuals who received drug-coated balloon (DCB) treatment (n=177), and the non-ISR group, comprising patients who did not receive DCB treatment (n=340). To gather relevant data, we meticulously reviewed the medical records and analyzed the findings from coronary angiography to assess the clinical characteristics of the patients. Results Patients with three-vessel disease (3VD) exhibited a higher prevalence of underlying diseases and were more likely to be taking aspirin and clopidogrel. Moreover, our analysis revealed that age (adjusted odds ratio [aOR] 1.02, 95% confidence interval [CI] 1.00 - 1.04, p = 0.037) and the presence of 3VD (adjusted odds ratio [aOR] 2.15, 95% confidence interval [CI] 1.03 - 4.46, p = 0.039) were significantly associated with an increased risk of coronary ISR. Conclusions Older age and 3VD were the independent predictors of coronary ISR in CAD patients receiving coronary stent implantation.

Background and Objectives: Fifty percent of individuals with borderline personality disorder (BPD) experience Non-Suicidal Self-Injury (NSSI). One of the crucial factors related to NSSI is the feeling of emptiness. Although some inner strengths, such as five precepts, meditation, and equanimity, have been identified as potential buffers against negative mental health outcomes in BPD, their role in mediating the relationship between emptiness and NSSI is not well-documented. This study aimed to explore how these inner strengths mediate the relationship between feelings of emptiness and NSSI in individuals with BPD symptoms. Materials and Methods: A total of 302 participants with BPD symptoms completed several assessments: the SCID-II Personality Disorder (Borderline PD) to assess feelings of emptiness and NSSI, the Inner-Strength-Based Inventory (i-SBI) to evaluate five precepts, meditation, and equanimity, and the Outcome Inventory Depression (OI-Dep) to assess depression. Mediation analysis was performed using IBM SPSS and AMOS, with NSSI as the outcome variable, feelings of emptiness as the predictor, and the inner strengths as mediators. Results: The participants had a mean age of 36.56, with 65.4% being female. The analysis showed that five precepts, meditation, and equanimity significantly mediated the relationship between feelings of emptiness and NSSI, with a standardized coefficient of β = 0.534 (95% CI = 0.417 to 0.647, p &lt; 0.001). The indirect effect of emptiness through these inner strengths was significant (β = 0.034, 95% CI = 0.009 to 0.075, p = 0.005). The mediation model explained 38% of the variance in NSSI with a 3% increase, albeit small but significant. Conclusions: The study highlights a negative mediating role of inner strengths in the relationship between feelings of emptiness and NSSI meaning that as these inner strengths increase, the direct impact of feelings of emptiness on NSSI decreases. This suggests that these inner strengths act as protective factors, reducing the likelihood that someone with feelings of emptiness will resort to NSSI as a coping mechanism. These findings suggest that targeting these inner strengths could be a valuable strategy in developing interventions aimed at reducing NSSI by addressing the underlying emotional challenges associated with BPD.

Sign language recognition technology can help people with hearing impairments to communicate with those who are hearing impaired. At present, with the rapid development of society, deep learning technology also provided certain technical support for sign language recognition work. In sign language recognition tasks, the use of traditional convolutional neural networks to extract spatio-temporal features from sign language videos suffers from insufficient feature extraction, resulting in low recognition rates. Nevertheless, video-based sign language datasets are very large and require a lot of computational resources for training and generalisation must be ensured, which poses a challenge for recognition. In this paper, we have presented a video-based sign language recognition method based on resnet and lstm. As the number of network layers increases, the ResNet network can effectively solve the granularity explosion problem and obtain better time series features. We use the Resnet convolutional network as the backbone model. At the initialisation stage, we obtain sign language features using ResNet; then, the learned feature space is used as the input of LSTM network to obtain long sequence features. The experimental results show that the accuracy of the above model is better than the mainstream model, and it can effectively extract the spatio-temporal features in sign language videos and improve the recognition rate of sign language actions.

Betel quid (BQ) use disorder (BUD) is prevalent in many Asian countries, impacting approximately 600 million people. We conducted a randomized clinical trial to analyze the impact of MAOA genetic variations on the severity of BQ craving. This was measured using DSM-5 criteria and Yale-Brown Obsessive Compulsive Scale modified for betel-quid (Y-BOCS-BQ). Participants were grouped according to the severity of BUD and MAOA gene single nucleotide polymorphism (SNP) rs5953210 genotypes. Y-BOCS-BQ were assessed at baseline (week 0) and during follow-up at weeks 2, 4, 6, and 8. The AA genotype group showed significantly greater reductions in Y-BOCS-BQ at weeks 2 (p=0.0194), 4 (p=0.0078), 6 (p=0.0277), and 8 (p=0.0376) compared to the GG genotype group. Additionally, within the antidepressant group, the AA genotype showed significant reductions in Y-BOCS-BQ at weeks 2 (p=0.0313), 4 (p=0.0134), 6 (p=0.0061), and 8 (p=0.0241) compared to the GG genotype. Statistical analysis revealed a significant interaction between the treatment and placebo groups based on MAOA genotypes, with the AA genotype in the treatment group exhibiting a more pronounced decrease in Y-BOCS-BQ (p interaction <0.05) at week 6. These findings highlight the importance of considering genetic factors when developing personalized treatment plans for BUD.

Background Diabetic patients have an increased risk of infections; however, the association between type 2 diabetes and hospital outcomes of sepsis remains controversial when the diabetes severity is not considered. We examined this association using nationwide and hospital-based databases concomitantly. Methods The first part of this study was conducted using 2 nationwide databases: the Longitudinal Cohort of Diabetes Patients and the Longitudinal Health Insurance Database 2000. The diabetic complication burden was evaluated using the adapted Diabetes Complications Severity Index score (aDCSI score). In the second part, we used the hospital-based database with laboratory data, such as initial blood glucose and HbA1c levels, to make comparisons between surviving and dead patients with type 2 diabetes and sepsis. Results The nationwide study included 19,719 type 2 diabetic sepsis patients and an equal number of non-diabetic patients. The diabetic sepsis patients had an increased odds ratio (OR) of 1.14 (95% CI 1.1-1.19) for hospital mortality. The OR for mortality increased as the complication burden increased (diabetic sepsis patients with aDCSI scores of 0, 1, 2, 3, 4, and ≥5 had ORs of 0.91, 0.87, 1.14, 1.25, 1.56, and 1.77 for mortality, respectively (all P<0.001 and P for trend <0.001)). A total of 1,054 diabetic sepsis patients were included from the hospital-based database. Initial blood glucose levels in the surviving and dead diabetic sepsis patients did not differ significantly: 273.9 ± 180.3 versus 266.1 ± 200.2 (mg/dL) (P=0.095). Moreover, the surviving diabetic sepsis patients did not have a lower HbA1c (%): 8.4 ± 2.6 versus 8.0 ± 2.5 (P=0.078). Conclusions In the case of type 2 diabetic sepsis patients, the diabetes-related complication burden is the major determinant of hospital mortality rather than the diabetes itself. Contrary to popular belief, initial blood glucose and HbA1c levels may not be as important as previously thought.

In northern Thailand, the problem of small particulate matter happens every year, with the pri-mary source being agricultural weed burning and wildfire. The tourism industry is strongly impacted and has been the spotlight for the past few years. Thus, the study aims to investigate the effect of small particulate matter on tourism and related SMEs in Chiang Mai, Thailand. The data was collected from 286 entrepreneurs in the tourism and related SMEs sectors. The data was analyzed using data mining and association rule techniques. The study revealed that small particulate matter has a considerable impact on customer factors, especially the number of customers has decreased. Operational factors and prod-uct/service factors are also affected by the dust in the form of adjustments to keep the business running and the protection of the health of employees and customers. Certainly, financial factors are affected by the small particulate matter situation, both lower revenues and higher costs.

In the last decades, cultivation of chia (Salvia hispanica L.) has expanded around the world and the seeds have become well known due to their rich composition in nutrients and bioactive compounds. The aim of this work was to evaluate the physical, chemical and nutritional profile of eight chia seeds grown in different Latin-American countries (Argentina, Bolivia, Chile, Ecuador, Mexico, Paraguay and Peru). The results showed that several nutritional parameters such as the protein content and amino acid profile, dietary fiber content, lipid content, mineral composition and phytate present in the seeds depend on the location they were grown in. Other parameters such as ash content, fatty acid profile or physical parameters were uniform across locations (except for color parameters). The results support the notion that nutritional characteristics of seeds are determined by the seed's origin, further analysis is needed to define the exact mechanisms that control the changes in the seeds nutritional properties.

Background: Most sepsis patients died during their first episode and the long-term survival post discharge was low. Major adverse cardiovascular events and repeated infections were regarded as the major causes in such conditions. No definite medications were proven to effectively improve the long-term outcome. We aimed to examine the benefit of statins on the long-term outcome of survived sepsis patients. Methods: Between 1999 and 2013, a total of 220,082 patients with the first episode of sepsis hospitalization were included and 134,448 ones (61.09%) survived to discharge. The survived patients who subsequently had statins use of >30 cumulative defined daily doses (cDDDs) post discharge were defined as the statin users. After propensity score matching of 1:5, a total of 7,356 and 36,780 survived patients were retrieved as the study (statin-users) and comparison cohort (non-statin users), respectively. The main outcome was the long term survival post discharge. HR with 95% CI was calculated using the Cox regression model to evaluate the effectiveness of statins with further stratification analyses according to cDDDs. Results: The study cohort, that is, the statin users had an adjusted HR of 0.29 (95% CI, 0.27-0.31) in long term mortality rate compared with the comparison cohort. For statin users with the cDDDs of 30–180, 180–365, and >365, the adjusted HRs were 0.32, 0.22, and 0.16, respectively, (95% CI, 0.30-0.34, 0.19-0.26, and 0.12-0.23, respectively) compared with the non-statin users (defined as statins use <30 cDDDs post discharge), and the P for trend <.0001. In the sensitivity analysis, after excluding the survived patients who died within three and six months post discharge, the adjusted HR of statins use remained significant (0.35, 95% CI 0.32-0.37 and 0.42, 95% CI 0.39-0.45, respectively). Conclusions: Statins decreased the long-term mortality post sepsis. Further randomized control trial deserved to be conducted to confirm this observation.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

The formula Chong-Lou-Yao-Fang (CLYF) is an herbal medicinal formulation developed by the indigenous Naxi people for treating liver cancer. This study is to reveal the biological activity, potential targets, and molecular mechanisms of CLYF for cancer treatment through network pharmacology, molecular docking and in vitro experiments. 35 key compounds were screened from 176 active ingredients in CLYF, which played a vital role in the treatment of cancer, 20 core targets were filtered through protein–protein interaction (PPI) network analysis. The enrichment analysis of Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) indicated that PI3K-Akt, MAPK, hepatitis B, hepatitis C might be effective in liver cancer treatment. Mo-lecular docking revealed stable binding between EGFR, TP53, and AKT1 with active ingredients. Experiments with cell cultures confirmed that CLYF-A suppressed the proliferation of HepG2 cells, which is consistent with the network pharmacology approach undertaken and the predictions of molecular docking. CLYF-A also induced significant apoptosis and cell cycle arrest in HepG2 cells, which was associated with the loss of mitochondrial membrane potential. This study explored the biological activity, potential targets, and molecular mechanisms of CLYF for cancer treatment. Our results may provide a scientific basis for the clinical use of CLYF for cancer treatment and have important implications for developing pharmaceutical preparations, which also need more phar-macological experiments.

The quality of healthcare services is a very important indicator of social welfare in developed and emerging countries. Good quality levels are critical to ensuring patient safety, improving health outcomes, increasing patient satisfaction, optimizing resource utilization, and meeting regulatory requirements. The stable and sustainable operation of medical institutions urgently requires the establishment of a reliable and effective medical quality performance evaluation platform. However, the complexity of the evaluation process, involving numerous evaluators and the consideration of different subjective and objective criteria, poses significant challenges and essentially constitutes a group multi-criteria decision-making problem. This article uses the overall medical environment of the institution, medical service attitude, medical security, administrative service measures, etc. as measurement standards to deal with this challenge. It proposes a medical service quality measurement model suitable for both qualitative and quantitative analysis. In view of the heterogeneity of information, the two-tuple fuzzy language calculation method is introduced to enable evaluators to skillfully manage diverse information and effectively avoid potential information omission problems in the subjective evaluation integration process. The effectiveness and feasibility of the model were demonstrated by applying it to the operational framework of a medical institution in central Taiwan.

Adlay (Coix lachryma-jobi L. var. ma-yuen Stapf) contains various phytonutrients for treating many diseases in Asia. To investigate whether orally administered of adlay bran oil (ABO) can cause drug interactions, the effects of ABO on the pharmacokinetics of five cytochrome P450 (CYP) probe drugs were evaluated. Rats were given a single oral dose (2.5 mL/kg BW) of ABO 1 h before administration of a drug cocktail either orally or intravenously, and blood was collected at various time points. A single oral dose of ABO administration did not affect the pharmacokinetics of five probe drugs when given as a drug cocktail intravenously. However, ABO increased plasma theophylline, dextromethorphan, and diltiazem when co-administered an oral drug cocktail. After 7-days of feeding with an ABO-containing diet, plasma concentrations of theophylline and chlorzoxazone were increased after oral administration of drug cocktail. The major CYP enzyme activities in liver and intestinal were not affected by ABO treatment. Results from this study indicate that a single oral dose or short-term administration of ABO may increase plasma drug concentrations when ABO is given concomitantly with drugs. ABO is likely to enhance intestinal drug absorption. Therefore, caution is needed to avoid food-drug interactions between ABO and co-administered drugs.

Among the plant resources in pre-Columbian Mexico and Central America, the Chia (Salvia hispanica L.) is unique in being the only member of the Lamiaceae cultivated for the mericarps. Recently the crop has gained considerable attention due to its high of content omega-3 polyunsaturated fatty acid, antioxidants, fibre and protein classifying it as a nutraceutical.

Hyperuricemia (HC) was one of the important risk factors for gout, arteriosclerosis, and cardiovascular disease. Animal studies have shown that Lactobacillus plantarum can improve the microbiota, immune regulation, and inhibit the uric acid production. However, it was not clear whether L. plantarum can improve HC and intestinal microbiota. We used potassium oxonate (PO) to induce HC in male SD rats, and then treated L. plantarum TCI227 in a dose dependent (HC+LD, HC+MD, HC+HD) for 4 weeks, and examined weight organs, biochemical examination of blood and urine, and analyzed the intestinal microbiota in feces by 16s rDNA sequence analysis. In this study, TCI227 improved body weight, decreased creatinine, serum uric acid, and increased urine uric acid compared to the HC group. Furthermore, TCI227 increased short-chain fatty acids (SCFAs). In fecal microbiota (family), TCI227 increased the level of Lactobacillaceae, and then decreased the level of Deferribacteres and Prevotellaceae compared to the HC group. Finally, in fecal microbiota (genus), TCI227 decreased the level of Prevotella, and then increased the level of Lactobacillus and Ruminococcus compared to the HC group. This study suggested that TCI227 can improve HC and change the compositions of the intestinal microbiota in PO induced male HC SD rats.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

In fuzzy decision problems, the ordering of fuzzy numbers is the basic problem. Among which, the fuzzy preference relation is the reasonable one to represent preference relation by a fuzzy membership function. This paper studies the Nakamura’s and Kołodziejczyk’s preference relations. Eight cases of representing different level of overlapping between two triangular fuzzy numbers are considered. We analyze the ranking behaviors of all possible combinations of decomposition and intersection of two fuzzy numbers for the Nakamura’s and Kołodziejczyk’s preference relations of these test cases. The results indicate that the decomposition and intersection can affect the fuzzy preference relations, thereby the final total order relation of fuzzy numbers.

Current stock market forecasting methods encompass fundamental, technical, emotional, and bargaining factors. Predominantly, price prediction hinges on order volume and price, although correlating these two within existing models proves challenging. This study employs Cycle Generative Adversarial Network (Cycle GAN) to unravel the intricate price-volume relationship, combining it with Bollinger Bands for trading signal analysis, overcoming hurdles in short-term forecasting prevalent in numerical analysis and AI. Focusing on TSMC (2330.TW) stock price, the research leverages Cycle GAN in deep learning to master the price-volume nexus, juxtaposed with LSTM and RNN. Historical TSMC closing prices and transaction counts are model inputs, scrutinizing their interconnectedness for predictions. This innovative approach aligns stock price, volume, market value, taxes, and prior changes via system engineering. By intertwining Bollinger Bands with stock price forecasts, trading signals are distilled, factoring in extended index %b for a comprehensive market picture.

Tefluthrin (Tef) is categorized as a type-I pyrethroid insecticide, telmisartan (Tel) functions as an angiotensin II receptor blocker, and KB-R7943 was identified as an inhibitor of Na+-Ca2+ exchange process. However, the influence of these compounds on the amplitude and gating properties of voltage-gated Na+ current (INa) in neurons associated with pain signaling remains unclear. In cultured dorsal root ganglion (DRG) neurons, whole-cell current recordings revealed that Tef or Tel increased the peak amplitude of INa, concomitant with an elevation in the time constant of INa inactivation, particularly in the slow component. Conversely, exposure to KB-R7943 resulted in a depression in INa, coupled with a decrease in the slow component of the inactivation time constant of INa. Theoretical simulations and bifurcation analyses were performed on a modeled interneuron in the spinal dorsal horn. The occurrence of INa inactivation accentuated the subthreshold oscillations (SO) in the membrane potential. With an increase in applied current, SO became more pronounced, accompanied by the emergence of high-frequency spiking (HF) with a frequency of approximately 150 Hz. Moreover, an elevation in INa conductance further intensified both SO and HF. Consequently, through experimental and in silico studies, this work reflects that Tef, Tel, or KB-R7943 significantly impacts the magnitude and gating properties of INa in neurons associated with pain signaling. The alterations in INa magnitude and gating in these neurons suggest a close relationship with pain transmission.

Physical activity is well-established as an important protective factor against degenerative conditions and a promoter of tissue growth and renewal. The discovery of FNDC5 as the precursor of irisin in 2012 sparked significant interest in its potential as a diagnostic biomarker and a therapeutic agent for various diseases. Clinical studies have examined the correlation between plasma irisin levels and pathological conditions using a range of assays, but the lack of reliable measurements for endogenous irisin has led to uncertainty about its prognostic/diagnostic potential as an exercise surrogate. Animal and tissue-engineering models have shown the protective effects of irisin treatment in reversing functional impairment and potentially permanent damage, but dosage ambiguities remain unresolved. This review provides a comprehensive examination of the clinical and basic studies of irisin in the context of degenerative conditions and explores its potential as a therapeutic approach in the physiological processes involved in tissue repair/regeneration.

Equality and incomparability multi-label ranking have not been introduced to learning before. This paper proposes new native ranker neural network to address the problem of multi-label ranking including incomparable preference orders using a new activation and error functions and new architecture. Preference Neural Network PNN solves the multi-label ranking problem, where labels may have indifference preference orders or subgroups which are equally ranked. PNN is a nondeep, multiple-value neuron, single middle layer and one or more output layers network. PNN uses a novel positive smooth staircase (PSS) or smooth staircase (SS) activation function and represents preference orders and Spearman ranking correlation as objective functions. It is introduced in two types, Type A is traditional NN architecture and Type B uses expanding architecture by introducing new type of hidden neuron has multiple activation function in middle layer and duplicated output layers to reinforce the ranking by increasing the number of weights. PNN accepts single data instance as inputs and output neurons represent the number of labels and output value represents the preference value. PNN is evaluated using a new preference mining data set that contains repeated label values which have not experimented on before. SS and PS speed-up the learning and PNN outperforms five previously proposed methods for strict label ranking in terms of accurate results with high computational efficiency.

Accuracy and computational cost are the main challenges of deep neural networks in image recognition. This paper proposes an efficient ranking reduction to binary classification approach using a new feed-forward network and feature selection based on ranking the image pixels. Preference net (PN) is a novel deep ranking learning approach based on Preference Neural Network (PNN), which uses new ranking objective function and positive smooth staircase (PSS) activation function to accelerate the image pixels’ ranking. PN has a new type of weighted kernel based on spearman ranking correlation instead of convolution to build the features matrix. The PN employs multiple kernels that have different sizes to partial rank image pixels’ in order to find the best features sequence. PN consists of multiple PNNs’ have shared output layer. Each ranker kernel has a separate PNN. The output results are converted to classification accuracy using the score function. PN has promising results comparing to the latest deep learning (DL) networks using the weighted average ensemble of each PN models for each kernel on CFAR-10 and Mnist-Fashion datasets in terms of accuracy and less computational cost.

Fall armyworm Spodoptera frugiperda (J.E. Smith, 1797) is a major pest of corn, rice, and sorghum among other crops usually controlled using synthetic or biological insecticides. Currently, the new invention of nanotechnology is taking root in the agricultural industry as an alternative source of pest management that is target-specific, safe, and efficient. This study sought to determine the efficacy of commercial Zinc Oxide (ZnO) nanoparticles (NPs) towards S. frugiperda under labora-tory conditions. ZnO NPs were diluted into different concentrations (100- 500ppm), where the baby corn used to feed the S. frugiperda larvae was dipped. The development of the insect feeding on food dipped in ZnO solution was significantly (p<0.05) affected, and the number of days that the insect took to complete its life cycle had a significant difference compared to the control. There was a significant difference in the adults’ emergence at all the concentrations of ZnO NPs compared to the control, with over 90% of the eggs successfully going through the cycle until adult emergence. Additionally, several malformations were observed throughout the lifecycle of the insect. Also, the fecundity of the females was greatly affected. The findings of this study suggest the possibility of exploitation of ZnO nanoparticles not only to eradicate S. frugiperda but to significantly reduce their population in the ecosystem through deformations, reduced fecundity, reduced oviposition, and hatchability of eggs. It will be a valuable tool in integrated pest management regimens.

(1) Background: Water resources at Chia lagoon experience possible threat to its sustainability. Communities are seeking alternatives to improve water quality at the lagoon. The study evaluated the extent at which local communities are WTP to improve water quality at Chia lagoon and the influencing factors. (2) Methods: A study was conducted at Chia lagoon, Western Part of Lake Malawi from November, 2015 to March, 2016. Wide range of data collection approaches such as household surveys, exploratory surveys, focus group discussions, key informant interviews and field observation were employed. A sample of 240 households were selected randomly. Qualitative data was analysed using content analysis. Multivariate logistic regression analysis was used to determine factors influence WTP. (3) Results: Out of 240 respondents, 57.4% expressed WTP. Multivariate logistic regression analysis demonstrated significant (P<0.01 or P<0.05) relationship between demographic (Gender, age, literacy level), social-economic (Land ownership, main agriculture water source and income) and institution (civic education and social network, extension, water user rights) factors and WTP. (4) Conclusion: The findings from this study provide significant clues for further research and baseline information for local government and local communities in development of more effective and holistic approaches to improve water quality.

One of the most important sources of energy is the sun. Taiwan is located at north 22-25° latitude. Due to its proximity to the equator, it experiences only a small angle of sunlight incidence. Its unique geographical location which can obtain sustainable and stable solar resources. This study takes research on the forecast of solar radiation to maximize the benefits of solar power generation, and develops methods that can predict the future solar radiation pattern to help reduce the costs of solar power generation. This study builds supervised machine learning models, known as deep neural network (DNN) and long short-term memory neural network (LSTM). The hybrid supervised and unsupervised model, namely cluster-based artificial neural network (k-means clustering and fuzzy C-means clustering-based models), was developed. After establishing these models, the study evaluated their prediction results. For different prediction periods, the study selected the best-performing model based on the results and proposed combining them to establish a real-time updated solar radiation forecast system capable of predicting the next 12 hours. The study area covered Kaohsiung, Hualien, and Penghu in Taiwan. Data from ground stations of the Central Weather Administration, collected between 1993 and 2021, as well as the solar angle parameters of each station, were used as input data for the model. The results of this study show that different models have their advantages and disadvantages in predicting different future times. Therefore, the hybrid prediction system can predict future solar radiation more accurately than a single model.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

Globally, road traffic collisions cause over a million deaths annually, with pedestrians accounting for nearly one-quarter (23%) of these fatalities. This casualty proportion highlights the critical importance of adhering to traffic regulations. This study analyzes the factors influencing driver yielding behavior at midblock crosswalk improvements, comparing (1) a typical zebra crossing (C1) and (2) an intelligent signalized crosswalk (C2). The study used video-based observational data to investigate driver behaviors and factors influencing driver behaviors. The study applied multinomial logistic regression to formulate yielding behavior models. The results indicate that the number of traffic lanes, width of the traffic lanes, width and length of the crosswalk, vulnerable group, the number of pedestrian crossings, pedestrian crossing time, the number of vehicles approaching a crosswalk, speed of vehicle, headway, the post-encroachment time (PET) between vehicles and pedestrian, and roadside parking are the significant factors influence yielding behavior. These findings provide a better understanding of the factors influencing driver yielding behavior and propose measures to set proper physical improvements (e.g., curb extensions, raised pedestrian platforms, and pedestrian fencing), enforcement (e.g., parking restriction, speed violation detection), public awareness campaigns, and education initiatives.

This paper presents the design of a robust speed controller for brushless DC motors (BLDCM) under field-oriented control (FOC). The proposed robust controller integrates extension theory (ET) and sliding mode theory (SMT) to achieve robustness. First, the speed difference between the speed command and the actual speed of the BLDCM, along with the rate of change of the speed difference, are divided into 20 interval categories. Then, the feedback speed difference and the rate of change of the speed difference are calculated for their extension correlation with each of the 20 interval categories. The interval category with the highest correlation is used to determine the appropriate control gain for the sliding mode speed controller. This gain adjustment tunes the parameters of the sliding surface in the SMT, thereby suppressing the overshoot of the motor speed. Because the sliding surface reaching law of the sliding mode controller (SMC) adopts the exponential approach law, the system's speed response can quickly follow the speed command in any state and exhibit excellent load regulation response. The simplicity of this robust control method, which requires minimal training data, facilitates easy implementation. Finally, the speed control of the BLDCM is simulated using Matlab/Simulink software, and the results are compared with those of the SMC using the constant speed approach law. The simulation results demonstrate that the proposed robust controller exhibits superior speed command tracking and load regulation response compared to the traditional SMC.

The impact of antecedent soil moisture content on soil erosion is a complicated phenomenon, which is still under argument with contradictions in research results. Hence, the objective of this study is to investigate the impact of antecedent soil moisture content to soil loss on clay soil by conducting two-year field experiments under natural rainfall on runoff plots with length of 10 meters, width of 3 meters, and uniform slope of 9%. Volumetric soil moisture sensors were used to log soil moisture changes, and soil moisture readings were used along with rainfall records to quantify the antecedent soil moisture conditions for each rainfall event. Results of this study show duration of the effective erosion event outranks the antecedent volumetric soil moisture content. Field study also suggests that accumulative rain falling within 48 hours (Pp48) prior to an effective erosion event strongly correlated with soil loss per Rainfall-Runoff Erosivity Index (Soil Loss / EI30), particularly when the duration of an effective erosion event is either between 3 ~ 7 hours or 10~ 30 hours. Hence, Pp48 can be considered as an alternative to replace antecedent soil moisture content in RUSLE 2’s cover and management factor.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Signal preprocessing and feature extraction are two important and necessary steps of data analysis. In signal analysis, typically these two steps are implemented through multiple algorithms. Moreover, the significant parameters in most algorithms are set empirically. We have developed an algorithm that can preserve and highlight characteristic waveforms while attenuating non-feature waveforms. The parameters in the algorithm are set through difference analysis. We have conducted experiments on both clinical and open-source ECG data, obtaining effective test results.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

Infrared sensors incorporating suspended zinc oxide (ZnO) pyroelectric films and thermally-insulated silicon substrates are fabricated using conventional MEMS-based thin-film deposition, photolithography, and etching techniques. The responsivity of the pyroelectric film is improved through annealing at 500℃ for 4 h. The voltage response of the fabricated sensors is evaluated experimentally for a substrate thickness of 1 µm over a sensing range of 30 cm. The results show that the voltage signal varies as an inverse exponential function of the distance. A positioning system based on three infrared sensors is implemented in LabVIEW. It is shown that the position estimates obtained using the proposed system are in excellent agreement with the actual locations. In general, the results presented in this study provide a useful source of reference for the further development of MEMS-based pyroelectric infrared sensors.

A new-type vibration sensor based on a fiber Bragg grating combining with a special structure-packaged design is proposed for monitoring the mechanical vibration signals. Three different sensing structures including the film squeeze type, new film squeeze type and elastic tape squeeze type are proposed for measuring the vibration signals with the frequency range from tens to thousands of Hz. In the comparison of experimental results, the new film squeeze structure has a nice sensing performance in the range from 100 to 1000 Hz with the sensitivity of 35 mV/V. For the elastic tape squeeze structure, the elastic tape is designed to encapsulate the optical fiber with a good frequency response from 1100 to 3100 Hz. In addition, by using the new film squeeze structure to measure the steady-state and non-steady-state vibration signals, the spectral components of sensing signals are analyzed by using the wavelet transformation for confirming the testing signals. These vibration fiber sensors can be applied in the measurement of high-end manufacture-facility vibration or earthquake vibrations etc.

The mystery phenomenon of fungal bioluminescence has always captivated human curiosity, although more attempts need to be made, particularly to bring the new species to the surface. In this study, we devoted considerable space to the taxonomy of these fungi while discussing their biogeography, evolution, bioluminescence mechanism, and potential ecological roles. We provide a detailed explanation of how these fungi produce light, including the role of the enzyme luciferase and luciferin. We also discussed their applications. Here, we presented an updated list of 122 bioluminescent fungi identified from five distinct evolutionary lineages viz. Armillaria, Eoscyphella, Lucentipes, Mycenoid, and Omphalotus worldwide, mainly in tropical and subtropical areas. The bioluminescent fungi descended from the last common ancestor of the mycenoid and the marasmioid clades of Agaricales, which have been maintained for at least 160 million years of evolution. We highlighted the need for further research to understand the ecological role of bioluminescent fungi. Applying bioluminescent fungi in various areas (e.g., environmental and medicinal) demonstrates their validity.

Hypertrophic Cardiomyopathy (HCM) is a common inherited disorder characterized by unexplained left ventricular hypertrophy, with or without left ventricular outflow tract (LVOT) obstruction. Single nuclei RNA-sequencing (snRNA-seq) of both obstructive and nonobstructive HCM patient samples have revealed alterations in communication between various cell types but a direct and integrated comparison between the two HCM phenotypes has not been reported. We performed a bioinformatic analysis of HCM snRNA-seq datasets from obstructive and nonobstructive patient samples to identify differentially expressed genes and distinctive patterns of intercellular communication. Differential gene expression analysis revealed 37 differentially expressed genes, predominantly in cardiomyocytes but also in other cell types, relevant to aging, muscle contraction, cell motility and the extracellular matrix. Intercellular communication was generally reduced in HCM, affecting the extracellular matrix, growth factor binding, integrin binding, PDGF binding and SMAD binding, but with increases in adenylate cyclase binding, calcium channel inhibitor activity, and serine-threonine kinase activity in nonobstructive HCM. Increases in neuron to leukocyte and dendritic cell communication, in fibroblast to leukocyte and dendritic cell communication and in endothelial cell communication to other cell types, largely through changes in expression of integrin-b1 and its cognate ligands, were also noted. These findings indicate both common and distinct physiological mechanisms affecting the pathogenesis of obstructive and nonobstructive HCM and provide opportunities for personalized management of different HCM phenotypes.

Mitral valve disease is a common heart disease in dogs. The aim of this study was to describe the cases of dogs who underwent mitral valve repair using a v-clamp device and to provide their long-term follow-up data on cardiac function after mitral valve repair. Four dogs with mitral valve regurgitation who experienced coughing and dyspnea underwent surgical mitral valve repair between December 2023 and June 2024. The patients were evaluated by transthoracic and transesophageal echocardiography. Echocardiography revealed mitral valve leaflet regurgitation. Mitral valve repair was performed under general anesthesia using a v-clamp device introduced through an introducer wire guide. Echocardiography was conducted at baseline and the 6-month follow-up. Blood analysis results after surgical repair were normal. Follow-up echocardiography revealed no complications related to the procedure, with all dogs demonstrating improved respiratory signs and quality of life after repair. No adverse reactions were reported after surgery. A v-clamp device was used to repair mitral valve regurgitation in four dogs. Mitral valve repair using a v-clamp device is another treatment option for mitral valve disease in dogs.

This paper presents the findings of an exploratory study on the continuously generating Big Data on Twitter related to the sharing of information, news, views, opinions, ideas, knowledge, feedback, and experiences about the COVID-19 pandemic, with a specific focus on the Omicron variant, which is the globally dominant variant of SARS-CoV-2 at this time. A total of 12028 tweets about the Omicron variant were studied, and the specific characteristics of tweets that were analyzed include - sentiment, language, source, type, and embedded URLs. The findings of this study are manifold. First, from sentiment analysis, it was observed that 50.5% of tweets had the ‘neutral’ emotion. The other emotions - ‘bad’, ‘good’, ‘terrible’, and ‘great’ were found in 15.6%, 14.0%, 12.5%, and 7.5% of the tweets, respectively. Second, the findings of language interpretation showed that 65.9% of the tweets were posted in English. It was followed by Spanish or Castillian, French, Italian, Japanese, and other languages, which were found in 10.5%, 5.1%, 3.3%, 2.5%, and <2% of the tweets, respectively. Third, the findings from source tracking showed that “Twitter for Android” was associated with 35.2% of tweets. It was followed by “Twitter Web App”, “Twitter for iPhone”, “Twitter for iPad”, “TweetDeck”, and all other sources that accounted for 29.2%, 25.8%, 3.8%, 1.6%, and <1% of the tweets, respectively. Fourth, studying the type of tweets revealed that retweets accounted for 60.8% of the tweets, it was followed by original tweets and replies that accounted for 19.8% and 19.4% of the tweets, respectively. Fifth, in terms of embedded URL analysis, the most common domains embedded in the tweets were found to be twitter.com, which was followed by biorxiv.org, nature.com, wapo.st, nzherald.co.nz, recvprofits.com, science.org, and other URLs. Finally, to support similar research and development in this field centered around the analysis of tweets, we have developed an open-access Twitter dataset that comprises tweets about the SARS-CoV-2 omicron variant since the first detected case of this variant on November 24, 2021.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

In all areas of medicine, especially in radiology, computers are increasing year by year. Filmless radiology, speech recognition software, electronic application forms, and teleradiology are recent developments that have greatly improved radiologists' performance. This research explores radiology software trends, predictions, and the challenges posed by informatics and historical trend analysis. The rationale behind this research is that information technology (IT) is overgrowing almost every day. We must continuously seek new ways to apply IT to make more use of resources. Consequently, IT becomes increasingly crucial to radiology organizations' innovative thinking, workflow, and business models. This study aimed to analyze all radiology software publications in the Science Citation Index (SCI). From 1991 to July 2021, SCI was used to search for publications systematically. We have also widely used this historical method in radiology software research. The findings and discussions are base on an assessment of trends, predictions, contributions, and challenges in radiology software, and we are exploring radiology software with six evolutionary stages. The gift of this research is that radiology managers realize that the use of new information technologies is closely related to survival in a competitive environment. Radiology companies can review these new technologies to develop more innovative business models and services to improve operational deficiencies.

This study encourages volunteer managers to innovate when enhancing volunteers' organizational commitment by adopting the new variable of psychological ownership, thus creating new management practices and systems. The findings indicate that psychological ownership significantly affects organizational commitment and can also enhance it through the partial mediating effect of volunteer motivation. Evidently, psychological ownership can become a major factor influencing volunteer retention. Consequently, two innovative management strategies are suggested to foster volunteer organizational commitment: Firstly, construct a diverse knowledge base for volunteer managers, facilitating a cognitive shift in leaders to enhance leadership, achieve better information sharing, and collaboration using diverse knowledge. Secondly, treat the organization's volunteers as a subsystem, develop psychological ownership as the foundation for system operations, integrate the volunteer system with the staff system through a decentralized decision-making structure, 'empower' the volunteer system, and stimulate members' sense of participation and responsibility, thereby fostering innovation and continuous improvement.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

The study investigated the relationships between sarcopenia, frailty, and related factors in hemodialysis patients with chronic kidney disease. A prospective cross-sectional study with convenience sampling was conducted between August 2021 and February 2022 at a hospital-affiliated hemodialysis center. Ninety-six hemodialysis patients participated in the study. Quantitative data were collected with structured interviews. Sarcopenia was determined with a rapid screening tool. Frailty was determined with the Rockwood clinical frailty score. Descriptive analysis, Person Correlations, and Linear regression analysis were used to evaluate the associations between frailty, sarcopenia, and health-related factors in hemodialysis patients. The mean age of the participants was 65.4 11.5 years, with an average of 95.0 77.5 months of hemodialysis. The most common comorbidity was hypertension (72.9%), followed by diabetes mellitus (39.6%) and cardiovascular health problems (35.4%). A significant difference in frailty between sarcopenia patients and a healthy population (X2 =9.51, p &lt;.001) was identified. There was a strong negative correlation (r= −.853, p&lt;.001) between sarcopenia and frailty, while moderate correlations between sarcopenia and frailty in sarcopenia patients (r= −.66, p&lt;.001) and a healthy population (r= −.58, p&lt;.001) were observed. Age, body weight before dialysis, and hand grip strength were found to be potential predictors of sarcopenia and frailty. Left calf circumference was significantly associated with sarcopenia (ß= −.128, p = .049). Age, body weight before dialysis, and hand grip strength are potential predictors of sarcopenia and frailty in hemodialysis patients with chronic kidney disease. Comorbidities, which may be preventable, are common in this population.

Simulating the non-perturbative and non-Markovian dynamics of open quantum systems is a very challenging many body problem, due to the need to evolve both the system and its environments on an equal footing. Tensor network and matrix product states (MPS) have emerged as powerful tools for open system models, but the numerical resources required to treat finite temperature environments grow extremely rapidly and limit their applications. In this study we use time-dependent variational evolution of MPS to expore the striking theory of Tamescelli et al. that shows how finite temperture open dyanmics can be obtained from zero temperature, i.e. pure wave function, simulations. Using this approach, we produce a benchmark data set for the dynamics of the Ohmic spin-boson model across a wide range of coupling and temperatures, and also present detailed analysis of the numerical costs of simulating non-equilibrium steady states, such as those emerging from the non-perturbative coupling of a qubit to baths at different temperatures. Despite ever growing resource requirements, we find that converged non-perturbative results can be obtained, and we discuss a number of recent ideas and numerical techniques that should allow wide application of MPS to complex open quantum systems.

Iron overnutrition has been implicated with higher risk of developing metabolic and cardiovascular diseases, including metabolic syndrome (MetS), while iron deficiency anemia exacerbates many underlying chronic conditions. Hemoglobin (Hb) concentration in the blood, which reflects a major functional iron (i.e., heme iron) in the body, may serve as a surrogate of iron nutrition status. We conducted sex-specific observational association studies where we carefully titrated the association between Hb deciles and MetS and its components among the Taiwanese Han Chinese (HC) from the Taiwan Biobank and Europeans of White ancestry from the UK Biobank, representing two large ethnicities. Our data show that at higher-than-normal levels of Hb, increasing deciles of Hb concentration were significantly associated with MetS across all sex subgroups in both ethnicities, with the highest deciles resulting in up to three times greater risks than the reference group [Taiwanese HC: OR=3.17 (95% CI, 2.75-3.67) for Hb >16.5 g/dL in men, OR=3.11 (2.78-3.47) for Hb >14.5 g/dL in women; European Whites: OR=1.89 (1.80-1.98) for Hb >16.24 g/dL in men, OR=2.35 (2.24-2.47) for Hb >14.68 g/dL in women]. The association between stronger risks and increasing Hb deciles was similarly observed with all metabolic components except diabetes. Here we found that both the highest Hb decile groups and contrarily the lowest ones, with respect to the reference, were associated with higher odds of diabetes in both ethnic groups [e.g., Taiwanese HC men: OR=1.64 (1.33-2.02) for Hb >16.5 g/dL, OR=1.71 (1.39-2.10) for Hb <13.5 g/dL; European Whites women: OR=1.39 (1.26-1.45) for Hb >14.68 g/dL, OR=1.81 (1.63-2.01) for Hb <12.39 g/dL]. These findings confirm that elevated Hb concentrations, a potential indicator of iron overnutrition, may play a role in the pathophysiology of MetS and metabolic components.

The consumption of fiber in the human diet is a global recommendation to ensure a healthy diet. Quinoa (Chenopodium quinoa Willd.), a gluten-free grain, and chia (Salvia hispanica), a seed, contain high fiber content and both have the potential to be explored in the development of nutraceutical and pharmaceutical formulations. An interesting characteristic of chia is its ability to form viscous mucilage when in contact with water, bringing the prospect of a binder in solid formulations. To produce tablets with a high fiber content, it is more appropriate to transform the material into granules using a wet process, with the help of a tool that exploits this possibility. Therefore, the objective of the present work was to study, using the Mixer Torque Rheometer, the feasibility of using chia as a binder to produce granulated quinoa and the development of chewable tablets. To this end, an experimental design was carried out to evaluate the impact of variables on the rheometer results for subsequent granulation. It was possible to obtain the granulation point for the formulations and after producing the granules, physical tests were carried out in which we noticed improvements in the flow. In the end, a formulation was selected for the development of chewable tablets containing quinoa and chia fibers.

Previous research has paid little attention to the relationship between corporate governance and brand equity in the tourism industry. This study aims to investigate the moderating effect of corporate governance (CG) on the relationship between brand equity (BE) and corporate profit-ability (CP) with ten control variables including five company characteristics and five macroeconomic variables. Financial data is retrieved from the Taiwan Economics Journal Database (TEJ), covering a total of 196 records from 32 listed companies for 16 years. Results indicate that BE has a significantly positive impact on CP in Taiwanese-listed tourism companies, and that CG moderates the relationship between BE and CP. These findings could help management executives enhance profitability by deepening BE and CG in the tourism industry. Managerial implications are also discussed.

For many decades, X-ray diffraction (XRD) has been used for material characterization. With the recent development in material science understanding and technology, various new materials are being developed, which requires upgrading the existing analytical techniques such that intricate problems can be solved. Although, XRD is a well-established non-destructive technique, it still requires further improvements in its characterization capabilities, especially when dealing with complex mineral structures. The present review conducts comprehensive discussions on atomic crystal structure, XRD principle, its applications, uncertainty during XRD analysis, and required safety precautions, all in one place. It further discusses the future research directions, especially the use of artificial intelligence and machine learning tools for improving the effectiveness and accuracy of XRD technique for mineral characterization. It has been focused that how XRD patterns can be utilized for a thorough understanding of the crystalline structure, size, and orientation, dislocation density, phase identification, quantification, and transformation, information about lattice parameters, residual stress, and strain, and thermal expansion coefficient of materials. All these important discussions on XRD for mineral characterization are compiled in this short yet comprehensive review that would benefit specialists and engineers in the chemical, mining, iron, metallurgy, and steel industries.

Introduction: Obstructive sleep apnea (OSA) is not only common in the general population but even more so in patients with tumors of the head and neck region. Untreated, it leads to reduced quality of life, increased daytime sleepiness, and other comorbidities. The aim of this study was to determine the difference in the occurrence of OSA in the patient population with head and neck tumors compared to the general population as represented by the Trend cohort of the Study of Health in Pomerania (SHIP) , and to assess the influence of tumor treatment. Methods: Between July 2018 and December 2021, preoperative polysomnography was conducted in 47 patients with histologically confirmed squamous cell carcinoma in the oropharynx, hypo-pharynx, or larynx. A follow-up polysomnography was performed in 23 patients 2-11 months af-ter completing treatment. The collected data was correlated with tumor treatment and tumor size. Results: Of the included patients, 43 were male and four were female. Age ranged from 54 to 90 years. The pretherapeutic measurement found no significant difference in the prevalence of a pathologically elevated apnea-hypopnea index (AHI) in our patients compared to the SHIP-Trend cohort. In the follow-up measurement after treatment completion, a significant deterioration in AHI was observed. Initially, 70 % of patients had an AHI > 5, after therapy this increased to 87 %. The effect was particularly pronounced in the group of patients with advanced tumor stages who had received primary chemoradiation. Conclusion: OSA is a relevant condition in patients with head and neck cancer. Tumor treatment can lead to an increased occurrence of sleep-related breathing disorders, especially in patients with advanced tumor stages undergoing primary chemoradiation. Additional studies are neces-sary to better understand the exact mechanism involved.

Phage, which is often used therapeutically, has begun to receive interest as an alternative to antibiotic growth promoters (AGPs) to enhance chicken growth. Another option that has been extensively studied as a growth promoter in chicken is probiotics. However, there are no studies using phages and probiotics as prospective feed additives for broiler chickens. Therefore, this study demonstrated the effects of phage cocktail, probiotics and their combinations on growth performance and gut microbiota of broiler chickens. A total of 288 one-day-old male Cobb 500 broilers were randomly allotted to 1 of 6 treatments in a completely randomised design. The treatments were: (i) C (basal diet (BD) only), (ii) 1ɸ (BD + 0.1% phage cocktail), (iii) 2ɸ (BD + 0.2% phage cocktail), (iv) P (BD + 0.1% probiotic), (v) 1ɸP (BD + 0.1% phage cocktail + 0.1% probiotic), (vi) 2ɸP (BD + 0.2% phage cocktail + 0.1% probiotic). The 1ɸP treatment had significantly (P < 0.05) better BW (35 d), BWG (22 – 35 d, 1 – 35d), and FCR (1-21 d. 22-35 d, 1-35 d) compared to C. Unique gut microbiota diversity was also found between the ɸP (1ɸP and 2ɸP) and non-ɸP groups (C, 1ɸ, 2ɸ and P) in ilea, particularly in the 35 d chickens. Microorganisms associated with short-chain fatty acid (SCFA) producers were significantly (P <0.05) present in the ɸP group than in the non- ɸP group. The carbohydrate and amino acid metabolism predicted genes were significantly upregulated in ɸP groups compared to non- ɸP groups. These genes were involved in the digestion and absorption of nutrients as well as the production of energy. Our findings showed that 1ɸP treatment could be a potential alternative to AGPs for poultry where growth performance was enhanced, and gut microbiota was positively modulated.

It is well known that that there is an intrinsic link between the financial and energy sectors, which can be analyzed through their spillover effects, which are measures of how the shocks to returns in different assets affect each other’s subsequent volatility in both spot and futures markets. Financial derivatives, which are not only highly representative of the underlying indices, but can also be traded on both the spot and futures markets, include Exchange Traded Funds (ETFs), a tradable spot index whose aim is to replicate the return of an underlying benchmark index. When ETF futures are not available to examine spillover effects, “generated regressors” are useful for constructing both Financial ETF futures and Energy ETF futures. The purpose of the paper is to investigate the co-volatility spillovers within and across the US energy and financial sectors in both spot and futures markets, by using “generated regressors” and a multivariate conditional volatility model, namely Diagonal BEKK. The daily data used are from 1998/12/23 to 2016/4/22. The data set is analyzed in its entirety, and are also subdivided into three distinct subsets. The empirical results show there is a significant relationship between the Financial ETF and Energy ETF in the spot and futures markets. Therefore, financial and energy ETFs are suitable for constructing a financial portfolio from an optimal risk management perspective, and also for dynamic hedging purposes.

Postoperative adhesive arachnoiditis is an inflammatory response of the spinal leptomeninges that occurs after surgery, resulting in scar formation in the avascular nature of the arachnoid layer. Clinical manifestations of this condition include pain, sensory deficits, motor dysfunction, reflex abnormalities, and bladder/bowel impairments. In MRI scans, the signs of postoperative adhesive arachnoiditis can vary, but some specific indicators can assist surgeons in locating the lesion and planning surgical interventions more accurately. In this report, we reported a 37-year-old man with postoperative adhesive arachnoiditis after two surgeries for Chiari I malformation, demonstrating that the gradually-forming the delta cord sign with sequential syringomyelia. During the intraoperative examination, we identified the presence of the delta cord sign, which was formed by an arachnoid scar that was tethering the dorsal spinal cord to the dura. This discovery allowed us to precisely pinpoint the location of the arachnoid scar, thereby providing valuable guidance to avoid any unnecessary exploration of innocent structures during the procedure. Other localization signs were also reviewed.

Biocompatible and biodegradable poly(butylene succinate-co-adipate) (PBSA)/hexadecylamine-modified PPZn (m-PPZn) nanocomposites were prepared using a melt mixing process. Experimental results of wide-angle X-ray diffraction and transmission electron microscopy revealed that the stacking layers of the m-PPZn were partially intercalated and partially exfoliated into the PBSA polymer matrix. The isothermal crystallization kinetics of PBSA/m-PPZn nanocomposites were studied at the temperature range of 62−70 °C and the half-time for crystallization of 3 wt % PBSA/m-PPZn nanocomposite was reduced by 27−35% compared with that of pure PBSA. This finding suggests that the incorporation of m-PPZn might cause the heterogeneous nucleation and the subsequent crystallization growth, which enhances the isothermal crystallization rate of PBSA/m-PPZn nanocomposite. The biodegradation rates of PBSA using Lipase from Pseudomonas sp. increase as the contents of m-PPZn increase. The degradation behavior of the neat PBSA investigated using the change of weight-average molecular weight belongs to exo-type hydrolysis activity. It is necessary to point out that the change of degree of crystallinity and degradation rate are almost linearly proportional to the loading of hexadecylamine-modified PPZn. This finding would provide an important information for the manufacturing biodegradable PBSA nanocomposites.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

Major depressive disorder (MDD) is one of the most prevalent and disabling mental disorders worldwide. Among the symptoms of MDD, sleep disturbance such as insomnia is prominent and the first reason patients may seek professional help. However, the underlying pathophysiology of this comorbidity is still elusive. Recently, genome-wide association studies (GWAS) have begun to unveil the genetic background of several psychiatric disorders, including MDD and insomnia. Identifying the shared genomic risk loci between comorbid psychiatric disorders could be a valuable strategy to understand their comorbidity. This study seeks to identify the shared genes and biological pathways between MDD and insomnia based on their shared genetic variants. First, we performed a meta-analysis based on the GWAS summary statistics of MDD and insomnia obtained from Psychiatric Genomics Consortium and UK Biobank, respectively. Next, we associated shared genetic variants to genes using two gene mapping strategies: (a) positional mapping based on genomic proximity and (b) expression quantitative trait loci (eQTL) mapping based on gene expression linkage across multiple tissues. As a result, a total of 719 shared genes were identified. Over half (51%) of them are protein-coding genes. Functional enrichment analysis shows that the most enriched biological pathways are related to epigenetic modification, sensory perception, and immunologic signatures. We also identified druggable targets using a network approach. Together these results may provide insights into understanding the genetic predisposition and underlying biological pathways of comorbid MDD and insomnia symptoms.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Based on the minimum conduction band edge caused by the minimum channel potential resulting from the quasi-3D scaling theory and the 3D density of state (DOS) accompanied by the Fermi-Dirac distribution function on the source and drain sides, a unified semiconductor-device-physics-based ballistic model is developed for the threshold voltage of modern multiple-gate (MG) transistors, including FinFET, W-gate MOSFET, and Nanosheet (NS) MOSFET. It is shown that the thin silicon, thin gate oxide, and high work function will alleviate the ballistic effects and resist the threshold voltage degradation. Besides, as the device dimension is further reduced to give rise to the 2D/1D DOS, the lowest conduction band edge is hence increased to resist the threshold voltage degradation. The nanosheet MOSFET exhibits the largest threshold voltage among the three transistors due to the smallest minimum conduction band edge caused by the quasi-3D minimum channel potential. Compared to P-type MOSFET (P-FET), the N-FET shows more threshold voltage because the electron has a more effective mass than the hole

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

This paper proposes an approach for image data extraction and driving behavior analysis using geographic information and driving data. Information derived from geographic and global positioning systems was used for image data extraction. In addition, we used an onboard diagnostic II and a controller area network bus logger to record driving data for driving behavior analysis. Driving behavior was analyzed using sparse automatic encoders and data exploration to detect abnormal and aggressive behavior. A regression analysis was used to derive the relationship between aggressive driving behavior and road facilities. Several traffic improvements were proposed for specific intersections and roads. The results indicate that lane ratios without lane markings and with straight lane markings are important features that affect aggressive driving behaviors.

Oriental lacquer, a natural and renewable polymeric coating, comes from the sap produced by lacquer trees. For practical application, oriental lacquer must be refined to reduce excess water and enhance its quality. In this study, drying oils were blended with oriental lacquer during the refining process to prepare an oil-modified refined lacquer (OMRL). The type and adding amount (0, 10, and 20% by wt.) of drying oils for wood coatings utilization were evaluated. Rhus succedanea oriental lacquer is composed of 54.1% urushiols, 34.3% water, 7.2% plant gum, and 4.4% nitrogenous compounds, and drying oils, including tung oil (TO), linseed oil (LO), and dehydrated castor oil (DCO) were used as materials in this study. The results show that the drying oil acts as a diluent, which reduces the viscosity and enhances the workability and could shorten the touch-free drying time and speed up the hardened drying of the OMRL. The results also indicate that the hardness, mass retention, Tg, tensile strength, abrasion resistance, and lightfastness of OMRL films decrease as more drying oils are blended. Conversely, the bending resistance, elongation at break, impact resistance increase, and particularly, the gloss, is greatly improved through the blending of more drying oils. In conclusion, the LO-modified refined lacquer (RL) has the highest film gloss and the DCO-modified RL has the shortest drying time for coating; otherwise, the film properties are similar among the three types of drying oil.

Background: The chin tuck maneuver has been suggested to increase suprahyoid muscle activation, but a method to measure the strength of the chin tuck maneuver has not been established. We developed a method to measure the strength of the chin tuck maneuver (chin tuck strength) and examined the reliability and validity of chin tuck strength measurement in community-dwelling older adults. Subjects and Methods: The participants were 233 older adults aged ≥65 years without dysphagia or physical disability. Chin tuck strength was measured twice consecutively using the developed device, and reproducibility was analyzed using intraclass correlation coefficients (ICCs). In addition, maximum tongue pressure, oral diadochokinesis, grip strength, knee extension strength, and the timed up and go test (TUGT) were measured as indices of swallowing-related muscle function and appendicular muscle function. The associations of chin tuck strength with swallowing-related muscle function and appendicular muscle function were analyzed statistically. Results: The ICCs for chin tuck strength were 0.82 (95% confidence interval [CI]: 0.73-0.88) in males and 0.87 (95%CI: 0.70-0.93) in females. Chin tuck strength was significantly associated with maximum tongue pressure, grip strength, knee extension strength, and TUGT. Conclusions: This study suggests that chin tuck strength is a reliable and valid assessment of swallowing-related muscle strength.

By using 0.35-um CMOS process, this work achieves a design of analogous band-gap reference voltage circuit with low temperature coefficient. The proposed circuit operates at 3V and generates a reference current of 44 uA. The HSPICE simulation results show the temperature coefficient of this circuit is 23 ppm/℃ at range of -10 ℃ to 100 ℃, and the line regulation (the ratio of output current variation to supply voltage variation) is estimated as 1.95 uA/V from supply voltage variation of 3 V to 5 V. The experimental chip is fabricated and measured. The circuit provides adjustable capability for output voltage among temperature variation of -10 - 100 ℃. The chip area is 534 × 695 um^2. In this new design, the operational amplifier is not necessary. The chip design effort can be great reduced.

This study investigates the asymmetric impacts of oil price changes on inflation in Algeria, Angola, Libya and Nigeria. Three different oil price data were applied in this study; the specific spot oil price of individual countries, the OPEC reference basket oil price and an average of the Brent, WTI and Dubai oil price. The dynamic panels ARDL were used to estimate the short and the long-run impacts. Also, this study partitioned the oil price into positive and negative changes to capture asymmetric impacts and found both positive and negative oil price changes positively influenced inflation. However, the impact was found to be more significant when oil prices dropped. The results from the study also found that money supply, the exchange rate and GDP are positively related to inflation while food production is negatively related to inflation. Accordingly, policymakers should be cautious in formulating policies between the positive and negative changes in oil prices as it was shown that inflation increased when the oil price dropped. Additionally, the use of contractionary monetary policy would help to reduce the inflation rate, and lastly, it is proposed that the government should encourage domestic food production both in quantity and quality to reduce inflation.

Torenia Concolor Lindley var. formosama Yamazaki ethanolic extract (TCEE) is reported to have anti-inflammatory and anti-obesity properties. However, the effects of TCEE and its underlying mechanisms in the activation of endothelial nitric oxide synthase (eNOS) have not yet been investigated. Increasing the endothelium-derived nitric oxide (NO) production has been known to be beneficial against the development of cardiovascular diseases. In this study, we investigated the effect of TCEE on eNOS activation and NO-related endothelial function and inflammation by using in vitro system. In endothelial cells (ECs), TCEE increased NO production in a concentration-dependent a manner without affecting the expression of eNOS. In addition, TCEE increased the phosphorylation of eNOS at serine 635 residue (Ser635) and Ser1179, Akt at Ser473, calmodulin kinase II (CaMKII) at threonine residue 286 (Thr286) and AMP-activated protein kinase (AMPK) at Thr172. Moreover, TCEE-induced NO production, and EC proliferation, migration and tube formation were diminished by pretreatment with LY294002 (an Akt inhibitor), KN62 (a CaMKII inhibitor) and compound C (an AMPK inhibitor). Additionally, TCEE attenuated the tumor necrosis factor-α-induced inflammatory response as evidenced by the expression of adhesion molecules in ECs and monocyte adhesion onto ECs. These inflammatory effects of TCEE were abolished by L-NG-nitroarginine methyl ester (a NOS inhibitor). Collectively, our findings suggest that TCEE confers protection from endothelial dysfunction by activating the Akt/CaMKII/AMPK/eNOS/NO signaling pathway.

The objective of this study is to investigate the use of excavation behavior prediction and analysis software in the field of civil en-gineering. PLAXIS and SoilWorks, widely used in the engineering and academic communities, were employed as research tools for analyzing gravel layers and deriving appropriate ranges of soil elastic modulus for different software programs. By collecting excavation cases in the Xindian area of New Taipei City, Taiwan, and conducting deep excavation analysis using the displacement of retaining walls, this study provides recommended ranges for localized selection of soil elastic modulus. The suggested range for PLAXIS is 7,840 N/m² to 9,800 N/m², while Soil-Works suggests a range of 2,450 N/m² to 3,430 N/m². These ranges allow for reasonable estimation of maximum deformations during the final excavation stage. Based on the research findings, it is recommended that engineers refer to the provided ranges when selecting soil elastic modulus for excavation analysis in gravel layers using different soft-ware programs in the Xindian area of Taiwan to improve the accuracy of deformation predictions during the final excavation stage. These results serve as important references for engineers and contribute to the effective prediction and management of excavation behavior in civil engineering projects.

Current-voltage characteristics curves of NFinFET are presented and are fitted with the modi-fied current-voltage (I-V) formulas, where the modified term in the triode region is demon-strated to be indispensable. In the as-known I-V formula, important parameters need determin-ing to make both the measured data and the fitting data as close as possible. Those parameters include kN (associated with the sizes of the transistor and mobility), (associated with Early Voltage), and Vth (the threshold voltage). The differences between the measured data and the fit-ting data vary as the applied source-drain bias, proving that the mobility of the carriers is not consistently constant. On the other hand, a modified formula, called kink effect factor, is nega-tively or positively added simulating solitary heat waves, which disturb the propagation of car-riers and thus influence the Source-Drain current (IDS). The new statistical standard deviations () are then found to be effectively suppressed as the kink effect is taken into account.

Building sustainable campuses has become a priority for various higher education institutes (HEIs). Internalization is one of the important tasks in the progress. Therefore, attracting and maintaining international faculty has converted to action for various internationalized campuses. During the COVID-19 pandemic, it has impacted most of the citizens’ life, while the international faculty members’ life might be tight during this period. The purpose of this study is to explore the perspectives of international faculty members on their life in higher education institutes by using partial least square structural equation modeling (PLS-SEM). Using a self-compiled online survey, we invited 80 international faculty members of HEIs in Taiwan to investigate this issue. The survey covers career and professional status, teaching and research status, and demographics of the faculty. This study proposes a novel conceptual framework for addressing international faculty’s campus life, the design will examine the relationships among working conditions, views of institutions, views of government’s measures, and levels of satisfaction through PLS-SEM. The demographic profile of the participants revealed (a) most international faculty are employed full-time as lecturers or assistant professors in most public universities; (b) most international faculty members earned their first degree outside of Taiwan; however, 66% of them earned their post-doctoral degrees in Taiwan. The results of PLS-SEM suggest that the international faculty perspective of government is more directly related to their current work satisfaction and overall satisfaction. The designed model has shown work well to assess this issue. This can be extended to other higher education settings to tackle similar issues.

Within the spectrum of a natural image, the amplitude of modulation decreases with spatial frequency. The speed of such an amplitude decrease, or the amplitude spectrum slope, of an image affects the perceived aesthetic value. Additionally, a human observer would consider a symmetric image more appealing than they do an asymmetric one. We investigated how these two factors jointly affect aesthetic preferences by manipulating both the amplitude spectrum slope and the symmetric level of images to assess their effects on aesthetic preference on a 6-point Likert scale. Our results showed that the preference ratings increased with the symmetry level but had an inverted U-shape relation to amplitude spectrum slope. In addition, a strong interaction existed between symmetry level and amplitude spectrum slope on preference rating, in that symmetry can amplify the amplitude spectrum slope’s effects. Such effects can be described by a quadratic function of the spectrum slope. That is, preference is an inverted U-shape function of spectrum slope whose intercept is determined by the number of symmetry axis. In addition, the interaction between the two factors is manifested as the modulation depth of the quadratic function.