Vibrations of blades and tower have important impact for wind turbine. This paper presents a active controller design to suppress blade edgewise vibrations under aerodynamic load and gravitational load.Treating the sum of aerodynamic load input in edgewise direction and gravitational load as unknown disturbance input,a stochastic disturbance accommodating control(SDAC) approach is proposed to design a controller which it utilizes a minimum-variance unbiased estimator(MVUE) to estimate both state and unknown input. The stability analysis proved that the proposed SDAC is bounded in mean square.In order to verify the performance of the minimum-variance unbiased estimator and the proposed SDAC, numerical simulations using Matlab/Simulink have been carried out for the National Renewable Energy Laboratory 5-MW wind turbine.Under the different circumstance which exists the random process and measure noise and noise free. It is shown that the estimation value by MVUE can tracking the real state and unknown input. The results are also compared to the traditional linear quadratic regulator(LQR) and show that the proposed stochastic disturbance accommodating control scheme can further reduce displacement in edgewise vibrations direction and the control strategy is more effective than the LQR.

To the best of the author’s knowledge, studies of mature plasmacytoid dendritic cell proliferation associated with T lymphoblastic lymphoma were extremely rare in the literature. Here, we report a patient who underwent both mature plasmacytoid dendritic cell proliferation and T lymphoblastic lymphoma. With the findings of lymph node biopsy taken from the right cervical and inguinal regions, we identified eye-catching mature plasmacytoid dendritic cells that were considered to be responsible for this lesion at the beginning, until the immunostaining of Ki67 and TDT showed a small group of positive cells hiding in these plasmacytoid dendritic cells. Bone marrow biopsy was also performed in this patient. Microscopically, the hematopoietic tissue was almost completely replaced by lymphoblastoid cells with condensed chromatin, inconspicuous nucleoli and scanty cytoplasm, which were basically the same as those seen in the lymph nodes in morphology. However, there was no sign of plasmacytoid dendritic cells or Langerhans cells in the bone marrow biopsy. With the help of bone marrow biopsy, our final diagnosis of the lymph node was T lymphoblastic lymphoma coexisting with mature plasmacytoid dendritic cell proliferation . Although accumulations of plasmacytoid dendritic cells may occur in some infections or reactive lymphadenopathy, the presence of extensive nodules or infiltration of plasmacytoid dendritic cells strongly reminds the pathologist to carefully evaluate the bone marrow or peripheral blood status of the patient to exclude a hidden myeloid or other neoplasm.

With reference to our 4G model of final unification, strong coupling constant and strong interaction charge of magnitude $e_s\cong 2.95e$, it is possible to understand the nuclear stability range with a simple power law of the form, $A_s\cong \left(Z+2.95\right)^{1.2\pm0.015}$

Feedback trading theory is one of the most primitive theories about financial market. But for a long time，researches and modelings on this topic are rarely seen. The model in this paper shows the effects of sentiment shocks on asset prices in a market characterized by feedback trading in the long run. We find that，generally，feedback trading will lead to cognitive bias effect and trading inducement effect. Cognitive bias effect increases with the feedback trading parameter ( FTP) . In our model，the abnormal volatility of asset prices is captured by cognitive bias effect，sentiment shock effect and trading inducement effect．

This paper explores how smart cities can cope with land subsidence and liquefaction in the context of rapid urbanization in Japan. Since the 1960s, liquefaction has become an important topic in geotechnical engineering, and great efforts have been made to evaluate the resistance of soil to liquefaction. There is currently a lack of machine learning applications specifically for smart cities in areas such as geological hazards. This study uses two machine learning techniques, artificial neural networks and ensemble learning, to obtain a prediction model with high performance in predicting the bearing layer depth to improve the accuracy of geo-engineering surveys. The model was developed by analyzing actual survey data from 433 locations in Setegaya, Tokyo, by using artificial neural networks (ANNs) and bagging, respectively. The results show that machine learning has great advantages in predicting the bearing layer depth. In addition, compared with a single model such as artificial neural networks, the prediction performance of ensemble learning can be improved by about 20%. Both interdisciplinary approaches can help predict address risks and thus promote sustainable urban development, highlighting the potential of smart cities in the future.

Fractional calculus is defined by expanded integer order integration and differentiation. In this paper, multiple mathematical models of a nonlinear dual tank device are precisely formulated by fractional calculus. Using the accurate model, multivariable Fractional-Order Controller is designed for the nonlinear device. The merits of the fractional-order design include: 1) Control of multivariable nonlinearities, 2) Compensation of uncertainties, 3) Elimination of coupling effects. Simulations and experiments are conducted to verify the precision of the fractional order models and the effectiveness of the multivariable fractional-order control design.

The continuous flowing spacetime forms a spacetime group G, one of its fundamental groups is the Poincare group PO(1,3), and the matter and interaction fields are representations of its intrinsic spacetime group. As a kind of quantized space-time unit, space-time group elements generate both space-time manifolds and matter. Matter and fields are aggregates of the quantum space-time within them and determine their type: the Lorentz group SO(1,3) represents a rotating spacetime corresponding to visible matter and the translation group P^1,3 represents a translational spacetime corresponding to dark matter and dark energy. The aggregation mode of space-time degrees of freedom in matter reveals that charge conjugation symmetry is the inverse symmetry of internal time of charged particles, and the external parity breaking of neutrinos is also due to their internal spatial aggregation mode.

Vertex-degree-based (VDB) topological indices have been applied in QSPR/QSAR. As an important category, the general logarithmic VDB topological index $T_{lnf}(G)$, is defined as the summation of $ln{f(d(u),d(v))}$, where the summation over all $uv\in E(G)$. In this paper, we give the sufficient conditions for that (1) the path $P_{n}$ is the only tree with the minimal $T_{lnf}$; (2) the star $S_n$ is the only tree with the maximal and the minimal $T_{lnf}$, respectively. As applications, the minimal and maximal trees of some logarithmic VDB indices are determined.

In this work, we discuss a newly proposed scalar-tensor theory in Minkowski spacetime. The basic frame in Minkowski spacetime is obtained. Consider a charged particle in the electromagnetic field, we make an attempt to connect this theory with conventional quantum theory. Two specific models are chosen to calculate values of the time delay.

The 2019 novel SARS-like coronavirus (SARS-CoV-2) entry depends on the host membrane serine protease TMPRSS2, which can be blocked by some clinically-proven drugs. Here we analyzed spatial relevance between glycosylation sequons and antibody epitopes and found that, different from SARS-CoV S, most high-surface-accessible epitopes of SARS-CoV-2 S are blocked by the glycosylation, and the optimal epitope with the highest surface accessibility is covered by the S1 cap. TMPRSS2 inhibitor treatments may prevent unmasking of this epitope and therefore prolong virus clearance and may induce antibody-dependent enhancement. Interestingly, a heparin-binding sequence immediately upstream of the S1/S2 cleavage site has been found in SARS-CoV-2 S but not in SARS-CoV S. Binding of SARS-CoV-2 with heparins may lead to exposure of S686, which then facilitates the S1/S2 cleavage, induces exposure of the optimal epitope, and therefore increases the antibody titres. A combination of heparin and vaccine (or convalescent serum) treatments thus is recommended.

Metastasis is a major cause factor for breast cancer (BC)-associated mortality. During the metastatic process, disseminated tumor cells (DTCs) detach from the primary sites, and enter the bloodstream and establish the secondary colonies. Recent studies have provided substantial evidence for the importance of Notch signaling in BC metastasis. Therefore, this review focuses on the mechanisms by which Notch contributes to the origin of BC DTCs, increases their motility, regulates their intravasation and extravasation, protects them from host surveillance, and finally facilitates colonization. Identification of the mechanisms underlying Notch-related BC metastasis will lead to the development of novel Notch-targeted therapeutic strategies to reduce metastasis and significantly improve outcomes.

This paper addresses challenges and solutions in urban development and infrastructure resilience, particularly in the context of Japan's rapidly urbanizing landscape. It explores the integration of smart city concepts to combat land subsidence and liquefaction, phenomena highlighted by the 2011 Great East Japan Earthquake. Using advanced technologies such as smart sensing and predictive analytics through kriging and ensemble learning, the study aims to improve the accuracy of geotechnical investigations and urban planning. By analyzing data from 433 geotechnical surveys in Setagaya, Tokyo, it develops predictive models to accurately determine the depth of bearing layers critical to urban infrastructure. The results demonstrate the superiority of ensemble learning in predicting the depth of bearing layers, with significant implications for smart city development and the sustainability of urban environments. This interdisciplinary approach not only seeks to mitigate risks associated with geological disturbances, but also promotes sustainable urban growth that prioritizes safety and prosperity. Through advanced technology and comprehensive research, the study underscores the potential of smart cities to address urban complexities and ensure a resilient, sustainable future.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

In this paper, we propose an assumption of which the relation between electron and phonon is discussed and investigated based on the experiment of γ photon and electric interconverting with each other. We calculated the charge of a particular standing wave topology with Maxwell’s equation rotated in accordance space with the SO3 transformation. The derived charge value is 1.6035 × 10E−19C around 0.0826% different from the experimental data, indicating the proposal is a promising theory to explain the origin of charge and spin of electron particle. Electron spin angular momentum comes from the orbital angular momentum of photon rotation (electromagnetic field rotation), and electron charge comes from photon, that is, the space-time rotation effect of electromagnetic wave.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

The space gravitational wave detection and drag free control requires the micro-thruster to have very low thrust noise within 0.1mHz~100mHz, which poses a great challenge to the ground thrust test. The evaluation and decoupling of thermal noise are the difficulties in the application of torsion balance for most thrusters dissipate heat in the experiment. The research has adopted a calibration scheme of micro-Newton thrust torsion balance. On the basis of Lisa Pathfinder's former research and using ideas inspired from PID control and multi time scale (MTS) for reference, the paper proposes to expand the state space of temperature to be applied on thrust prediction based on fine tree regression (FTR), to subtract the thermal noise filtered by transfer function fitted with z-domain vector fitting (ZDVF). The results show that the thrust amplitude thrust density in diurnal temperature fluctuation is decoupled from 24μN/Hz1/2 to 4.9μN/Hz1/2 at 0.11mHz. And the 1μN square wave modulations of electrostatic fins (ESF) is extracted from the simultaneously ambiguous background of temperature for PTC's heating and cooling. The FTR method is well demonstrated in thermal noise decoupling and can guide the design of thermal control and be extended to other physical quantities for noise decoupling.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

Cytochrome P450 monooxygenases (P450s) are promising versatile oxidative biocatalysts. However, the practical use of P450s in vitro is limited by their dependence on the co-enzyme NAD(P)H and the complex electron transport system. Using H2O2 simplifies the catalytic cycle of P450s; however, most P450s are inactive in the presence of H2O2. By mimicking the molecular structure and catalytic mechanism of natural peroxygenases and peroxidases, an artificial P450 peroxygenase system has been designed with the assistance of a dual-functional small molecule (DFSM). DFSMs, such as N-(ω-imidazolyl fatty acyl)-l-amino acids, use an acyl amino acid as an anchoring group to bind the enzyme, and the imidazolyl group at the other end functions as a general acid-base catalyst in the activation of H2O2. In combination with protein engineering, the DFSM-facilitated P450 peroxygenase system has been used in various oxidation reactions of non-native substrates, such as alkene epoxidation, thioanisole sulfoxidation, and alkanes and aromatic hydroxylation, which showed unique activities, and regio- and enantioselectivities when compared with native P450s. Moreover, the DFSM-facilitated P450 peroxygenase system can switch to the peroxidase mode by mechanism-guided protein engineering. In this short review, the design, mechanism, evolution, application, and perspective of these novel non-natural P450 peroxygenases for the oxidation of non-native substrates are discussed.

Excessive vibration of temporary grandstand owing to crowd has lateral rhythmic motions can cause human in panic, which attracted increasing attention in recent years. This paper focuses on experiments that a temporary grandstand occupied 20 participants is oscillated by a shaking table with a series of random waves and induced by crowd with rhythmic swaying motions at lateral direction, respectively. And then a series of vibration perception questionnaires about crowd reaction are obtained. Evaluation of annoying level derives in concept of degree of membership and annoying rate method is proposed, then the human health risk of vibration serviceability of temporary grandstand is assessed with acceleration vibration dose value(VDV). From these results it is clear that standing crowd is more tolerant to vibration than seated crowd. The measured vibrations generated by crowd activities on temporary grandstand can cause panic in crowd. New relationship between the annoyance rate and structural acceleration VDV at logarithmic coordinate is proposed. The findings of this study can be utilized to manage the vibration of temporary grandstand and assess the human health risk.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

In this work, we try to find a way to describe the physical law of micro-world under the frame of a space-time theory. By introducing the scalar fields $\mathcal{D}\left( x\right)$ and $\zeta\left( x\right) $, we rewrite the action of conventional field theory and the Lagrangian describing the motion of the particle, where a modified space-time relation is obtained. To test the correctness of this attempt, we demonstrate the Klein-Gordon equation by the Hamilton-Jacobi method in four dimensional form and present a time delay for the ground state of hydrogen atom.

Purpose: Physical activity (PA) is likely the most important modifiable element for the growth of skeletal muscle. However, a detailed investigation of PA’s impact on preschoolers’ of skeletal muscle development is lacking. This study aimed to determine whether PA level is related to skeletal muscle thickness among preschool children. Methods: 275 healthy preschoolers between the ages 4–6 were instructed to wear an accelerometer for 4 consecutive days. The daily steps and minutes spent in moderate-to-vigorous PA (MVPA) and total PA (TPA) were examined. Muscle thickness (MT) was measured by B-mode ultrasonography. The MT was measured at the anterior (AT) and posterior thigh (PT) and the anterior (AL) and posterior lower leg (PL). Results: Boys were more physically active and engaged in significantly more TPA and MVPA on weekdays compared with girls. Compared with that on the weekends, more physical activity, and significantly greater number of daily steps and higher TPA and MVPA were recorded for both boys and girls on the weekdays. Multivariable regression analyses, after adjusting for daylight duration, indicated that a daily increase in the TPA and MVPA would lead to higher muscle size in AT (β=1.11 and β=1.37, p<0.05), and PL (β=1.18 and β=0.94, p<0.05) among preschool children. Conclusions: The time spent involved in most of the different categories of MVPA was significantly higher for boys than for girls on the weekdays and weekends. MVPA was positively correlated with greater skeletal muscle development in the lower body.

The azimuth wheel-rail of large aperture radio telescope is the key component, it not only sup-ports the whole weight of the antenna, but also directly affects the pointing performance of the antenna with its surface accuracy. The whole weight of the radio telescope is hundreds or even thousands of tons, its azimuth frame rollers have great contact stress with the wheel-rail surface, repeated rolling can cause rolling contact fatigue on the wheel-rail surface, resulting in wear, cracks and other damage to the wheel-rail, and even lead to failure or fracture of the wheel-rail in serious cases, so it is very important to monitor the damage of the antenna wheel-rail. In order to visually detect the use of antenna wheel-rail surface, this paper proposed the method using electromagnetic ultrasonic detection to detect the damage of antenna wheel-rail surface for the first time. Based on the electromagnetic ultrasonic nondestructive testing principle, the simplified wheel-rail model containing wear, corrosion and crack damage is simulated. The results show that this method can effectively detect the surface damage of the antenna wheel-rail surface, and it can provide an important reference for the research of wheel-rail damage detection of large radio telescope.

The problems of operating range and costs are the two most critical bottlenecks restricting the extensive application of electric vehicles at home and abroad. There are also some prominent problems in China's electric vehicles, such as slow improvement of electric vehicle's operating range, difficulty in charging, slow charging, low utilization efficiency of charging resources, and high battery cost for electric vehicles, which lead to poor competitiveness of electric vehicles compared with traditional internal combustion engine (I.C.E.) vehicles. This paper analyzes the key factors restricting the development and popularization of electric vehicles in China from the aspects of strategic policy, sales situation and self problems. Through summarizing the experience and lessons of French standardization development strategy and electric vehicle development mode, this paper puts forward the hypothesis leading the development of electric vehicles through standardization to enhance their competitiveness, gives the specific suggestions, and briefly analyzes the feasibility from the aspects of product situation. The research content of this paper provides a certain basis and ideas for the future research work.

The coronavirus disease 2019 (COVID-19) has spread over the world for more than one year. COVID-19 often develops life-threatening hypoxemia. Endothelial injury caused by the viral infection leads to intravascular coagulation and ventilation-perfusion mismatch. However, besides above pathogenic mechanisms, the role of alveolar edema in the disease progression has not been discussed comprehensively. Since the exudation of pulmonary edema fluid was extremely serious in COVID-19 patients, we bring out a hypothesis that severity of alveolar edema may determine the size of poorly-ventilated area and the blood oxygen content. Treatments to pulmonary edema (alcohol-oxygen vapor therapy and fluid management) may be great helpful for reducing occurrence of severe cases. Given that late mechanical ventilation may cause mucus (edema fluid) to be blown to the deep of the small airways, oxygen therapy should be given at the early stages. The optimal time and SpO₂ threshold for oxygen therapy are also discussed.

Positioning based on wireless signals such as mobile communication networks has become an important means to provide high-precision location services in environments where satellite signals are blocked. In complex environments such as indoor and underground, wireless signal propagation is obstructed and non-line-of-sight (NLOS) phenomena appears due to serious occlusion and reflection. The time delay caused by NLOS effects has little impact on communication system but can significantly increase positioning errors in positioning systems. Therefore, effective suppression of NLOS errors is crucial to improving 5G positioning accuracy. To address the insufficient feature extraction of existing NLOS error suppression methods, the neglect of residual NLOS measurement errors, and poor stability of position estimation results, this paper innovatively proposes a NLOS mitigation and location estimation method for 5G positioning terminals. Simulation and experimental test results demonstrate that the proposed method outperforms the comparative methods both theoretically and practically, achieving an average positioning accuracy of 1.85 meters in complex indoor NLOS environments. The method proposed in this paper provides a new strategy for NLOS error suppression in indoor 5G positioning, which can significantly contribute to high-precision location services based on commercial 5G networks.

Air pollutants such as volatile organic compounds (VOCs), nitrogen oxides (NOx), sulfur dioxide (SO2), as well as water pollutants including heavy metal, are harmful to human and environment. Effective control and reduction of their pollution is therefore an important topic for today’s scientists. Fly ash (FA) is a type of industrial waste that can cause multiple environmental problems if discharged into the air. On the other hand, because of its high porosity, large specific surface area, and other unique characteristics, the FA can also be used as a low-cost and high efficient adsorbent with some simple modifications. This paper reviews the effects of FA on treatment of the above air and water pollution based on our research experience over many years, including to the current status of global FA utilization, physicochemical properties, principle of adsorption, and the application direction of FA in the future. It focuses on the use of nanocomposite technology to fabricate functional FA fibrous membranes to adsorb VOCs from air, and treat heavy metal wastewater. This present review first describes the fabrication technology of FA nanocomposites and their mechanism of adsorption VOCs from air. Utilization of nanofiber technology to fabricate multi-functional FA emerging composite materials to mitigate air and water pollution has great potential in the future, especially use of pollutant material to control other pollutants.

Landslides are serious geological hazards that become a disaster worldwide, causing a large number of casualties and economic losses every year. There are many factors affecting landslide susceptibility, such as rainfall, soil and slope. Each of them has an important role in the process of slope losing stability. In this paper, the effects of rainfall intensity, rainfall pattern, slope gradient and soil type on landslide susceptibility are studied. In the process of rainfall-induced landslide, the relevant physical quantities of soil changes continuously. Their values and processes are closely related to the time of landslide occurrence. Hence, the variation of soil volumetric water content, matrix suction, pore water pressure and total stress throughout the rainfall are measured. As the results, soil type, slope gradient and rainfall intensity have a large influence on landslide susceptibility. The occurrence of landslides has a prerequisite that the slope is greater than or equal to 15°. The rainfall intensity needs to be not less than 80 mm/h. The difference of rainfall pattern also affects the landslide susceptibility. The rainfall pattern with rainfall intensity peak at the later stage is more likely to induce landslide. Coarser soils with gravels are prone to landslides when other conditions are the same. Steeper slopes, stronger rainfall, and coarser soils can all increase the amount of sediment yield.

A face serum composed of a combination of biologically active compounds was evaluated for safety and efficacy in vitro, in a repeat insult patch test and in a human clinical efficacy trial. The serum inhibited tyrosinase activity modestly, decreased collagenase activity and exhibited notable free radical scavenging activity in vitro. It is gentle to the skin, as the serum did not irritate the skin or produce symptoms of allergic contact dermatitis in the 55 healthy adults that participated in the repeat insult patch test. In the efficacy trial, daily application of the face serum for 30 days significantly increased skin hydration, with all 35 volunteers experiencing improvement. Substantial improvements in skin elasticity, roughness (fine lines and wrinkles), and brightness also occurred during the trial. Dermatological examination also revealed a trend for reduced comedone count with use of the serum. Self-assessment responses revealed that all volunteers experienced improvements in multiple skin quality parameters and that participant perceptions are consistent with the results of the instrumental analyses. These findings indicated that the measured improvements in skin quality are not only statistically significant but are also clinically relevant as they were great enough for users of the face serum to feel and recognize.

The plant productivity-richness relationship (PPR) is one of the most debated and important issues in ecology. There have been distinct stages in the research of this issue, including the discovery of the different PPR shapes, respective tests of influencing processes, and integrative research with vegetation investigation, manipulation experiments, and theoretical analysis. The debate largely focuses on what the dominant shapes and underlying mechanisms are. Recent integrative research works following analyses of respective processes affecting PPR have found that the humped, asymptotic, positive, negative, and irregular shapes of PPR are linked to each other. One shape of PPR may change into another. The balance between positive and negative processes determines the different shapes of PPR. Plant diversity has a globally positive effect on plant productivity.

NongXiangXing Baijiu (NBJ) is produced using a solid-state fermentation system, but the impact of stratified fermented grains on fermentation remains unclear. Therefore, in a typical distillery plant, we evaluated the physical and chemical composition, volatile compound profile, and microbial community of fermented grains in NBJ both above (FG-A) and below (FG-B) the Huangshui line. Significant differences in fermentation parameters between FG-A and FG-B were observed after 30 days of fermentation (P < 0.05). Additionally, the partial least squares projection to latent structure discriminant analysis (PLS-DA) revealed distinct differences in volatile compounds between FG-B and FG-A, identifying 26 discriminant markers. The diversity of short-chain fatty acids (SCFAs) and their esters was higher in FG-B compared to FG-A. Furthermore, microbial diversity and abundance differed significantly between the two layers of fermented grains (P < 0.05). Correlation and pathway enrichment analyses indicated that the higher SCFA content in FG-B could be attributed to the greater abundance of acid-producing microorganisms compared to FG-A. This study highlights the differences between the two layers of fermented grains in NBJ fermentation, offering new insights into solid-state fermentation and expanding the current understanding of the traditional NBJ fermentation process.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

The synthesis 2-tert-butyl-4-methylphenol is of great significance because of its widely application in industry, and the development of highly efficient catalyst is necessary to the alkylation of p-cresol and tert-butyl alcohol. Here, an efficient and mild method was established, caprolactam was chosen as hydrogen-bonding acceptor, p-toluenesulfonic acid was employed as hydrogen-bonding donor, and deep eutectic solvent (DES) was prepared to catalyze the alkylation reaction. The structure of the DES catalyst was characterized by 1H NMR spectra, thermogravimetric analysis and fourier transform infrared spectra (FT-IR). In addition, response surface design based on Box-Behnken method was employed to optimize the alkylation reaction process parameters, the study of reaction kinetics was also carried out subsequently. The recycle performance of the catalyst was evaluated by recovery experiments, and a good result was obtained. Comparing with the literature reported, we here provide a mild method to the synthesis of 2-tert-butyl-4-methylphenol.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

Toxoplasma gondii, a protozoan parasite with the ability to infect various warm-blooded vertebrates, including humans, is the causative agent of toxoplasmosis. This infection poses significant risks, leading to severe complications in immunocompromised individuals and potentially affecting the fetus through congenital transmission. A comprehensive understanding of the intricate molecular interactions between T. gondii and its host is pivotal for the development of effective therapeutic strategies. This review emphasizes the crucial role of proteomics in T. gondii research, with a specific focus on host-parasite interactions, post-translational modifications (PTMs), PTM crosstalk, and ongoing efforts in drug discovery. Additionally, we provide an overview of recent advancements in proteomics techniques, encompassing interactome sample preparation methods such as BioID, APEX, and Y2H, as well as various proteomics approaches, including single-cell analysis, DIA, targeted, top-down, and plasma proteomics. Furthermore, we discuss the integration of proteomics with other omics technologies, highlighting its potential in unraveling the intricate mechanisms of T. gondii pathogenesis and identifying novel therapeutic targets.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

Over recent years, the importance of patent literature has become more recognized in the academic setting. In the context of artificial intelligence, deep learning, and data sciences, patents are relevant to not only industry but also academe and other communities. In this article, we focus on deep tomographic imaging and perform a preliminary landscape analysis of the related patent literature. Our search tool is PatSeer . Our patent bibliometric data is summarized in various figures and tables. In particular, we qualitatively analyze key deep tomographic patent literature.

By the study of the pattern book Ying Zao Fa Shi (building regulations of Song Dynasty, 1103 AD), while analyzing the combining and dimensioning rule of timber framework and tile work, a model self-generating program has been compiled for the first time. The operating framework has been firstly defined, while solving the issues of clustering principle, connecting method, output classification, etc. with the detailed description of algorithm theory. Taking the corner bracket set and nine-ridge roof for example, after the compilation and debug by Grasshopper, according to various input parameters, various models have been generated automatically by the plugin, proving the velocity and the veracity of the algorithm.

Preeclampsia (PE) continues to be a significant cause of maternal and neonatal morbidity and mortality. Angiotensin II type I receptor autoantibody (AT1-AA) has been reported accompanied by PE women in numerous studies. Therefore, detecting the mechanism of AT1-AA production is the key breakthrough in understanding PE. Deficiency in MFG-E8 has been verified can lead to autoimmune diseases due to dysfunction in macrophage phagocytosis and the production of autoantibodies. In the present study, we examined the expression of MFG-E8 in PE patients. Compared with the control, PE patients had a lower expression of placental MFG-E8 and a higher expression of placental AT1R. Then, we tested the effect of MFG-E8 on AT1-AA production and macrophage phagocytosis of trophoblast apoptosis in PE rats induced by low-dose endotoxin(LPS) and trophoblast model. In vivo, experiments results showed that systolic blood pressure, 24h urinary protein, serum TNF-α,sLFt-1 and AT1-AA levels, and placental trophoblast apoptosis caused by LPS were all significantly alleviated by MFG-E8. Moreover, administrated with MFG-E8 has shown decreased trophoblast apoptosis and AT1R exposure in vitro, and enhanced the phagocytosis of dead trophoblasts by macrophages. That supports the idea that MFG-E8 could be a potential therapeutic target for attenuating AT1-AA and protecting patients from AT1-AA and PE.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

The purpose of this study is to investigate and validate the influencing factors of audiences’ attitude toward virtual concerts. To address this issue, the current study proposes a conceptual model integrating player experiences’ factors (autonomy, relatedness, and engagement) and the technology acceptance model (perceived usefulness, perceived ease of use, and perceived enjoyment). An online questionnaire on virtual concert experiences was distributed to Chinese audiences who had attended virtual concerts. Structural equation modeling was then used to establish the relationship between variables. The results suggested autonomy, relatedness and engagement positively impacted perceived usefulness, perceived ease of use, and perceived enjoyment. Furthermore, the perceived usefulness, perceived ease of use, and perceived enjoyment were significant predictors of audiences’ attitude. The findings of this study can provide a reference for relevant virtual entertainment providers and can also serve as a point of development and exploration for technology acceptance model and player experience in the field of virtual concerts.

A long-term forecast study on the electricity demand of Taoussa of Mali is conducted in this paper, with various scenarios of socioeconomic and technological conditions. The analysis tool, which is applied in scenarios simulation, is the Model for Analysis of Energy Demand from the International Atomic Energy Agency. The analysis results are annual electricity demand and peak load forecast for the electrification from the period 2020 to 2035. During the planning period, the analysis results show that the electricity demand will increase to 49.40 MW (332.57 GWh) for the low scenario (LS), 66.46 MW (472.61 GWh) for the reference scenario (RS), and 89.47 MW (635 GWh) for the high scenario (HS). In addition, the total electricity demand increased at an average rate of 8.13% in the LS, 10.31% in the RS and 12.56% in the HS in all sectors. The electricity peak demand is expected to grow at 7.92%, 10.53% and 12.91% corresponding to the three scenarios; in this case, the system peak demand in 2035 will increase to 64.88 MW for the LS, 92.2 MW for the RS and 126.22 MW, the days of peak load are between 17th -23rd in May. The Industry sector will be the biggest electricity consumer of Taoussa area.

Chinese texts often feature a substantial volume of normative content, and their analysis has increasingly become a focal point in recent semantic analysis endeavors. Enhancing the effectiveness of text classification and clustering is pivotal in unveiling the intricate semantics within extensive textual data. Empirical research within the realm of computational social science has underscored the need for improved explanatory power when it comes to general text clustering methods applied to normative texts. This study introduces an innovative hierarchical clustering method that incorporates part-of-speech (POS) features and pioneers a novel semantic network model. It achieves this by amalgamating a POS-based feature weight calculation method with hierarchical clustering techniques. To assess its efficacy, the method is rigorously evaluated across three diverse text datasets, encompassing normative reports, news articles, and social media content. The experimental results unequivocally demonstrate the superior performance of the POS-HC method, surpassing the traditional TF and TF-IDF feature extraction methods in terms of clustering accuracy, and surpassing some existing clustering methods. Furthermore, its classification effectiveness exhibits notable advantages, particularly in the semantic classification of normative texts.

With the changing relationship between urban and rural areas in China, the rural areas are experiencing rapid social transformation. To ensure successful implementation of the rural revitalization strategy, land consolidation has become a major measure of rural economic reform. Existing research focuses on quantitative studies exploring the relationship between land consolidation and rural economic development, but there is a lack of studies on the relationship between land consolidation and social change. In this study, Jin’an Village is selected as the research area, using semi-structured interviews and semi-participatory observation to obtain original materials, aiming to make a detailed description of the specific practice of land consolidation, and to analyze the impact of land consolidation on the transformation of rural social consciousness. The study found that rural land consolidation involves villagers in the land consolidation process, which can effectively stimulate villagers’ participation in public affairs. Concurrently, the interaction between villagers and outside investors disrupts the conventional socialization model in rural areas and motivates villagers to act in accordance with contractual agreements. The conclusion is that land consolidation in rural areas can enhance the political democracy and legal consciousness of local villagers, which can lead to a change in local social consciousness. Our findings also emphasize the crucial necessity to grant rural villagers with improved accessibility to professional services and information, coupled with the continued promotion of land consolidation to advance modernization in these areas.

In response to increasing urbanization and the need for infrastructure resilient to natural hazards, this study introduces an AI-driven predictive model designed to assess the risk of soil liquefaction. Utilizing advanced ensemble machine learning techniques, the model integrates geotechnical and geographical data to accurately predict the potential for soil liquefaction in urban areas, with a specific focus on Yokohama, Japan. This methodology leverages comprehensive datasets from geological surveys and seismic activity to enhance urban planning and infrastructure development in smart cities. The primary outputs include detailed soil liquefaction risk maps that are essential for effective urban risk management. These maps support urban planners and engineers in making informed decisions, prioritizing safety, and promoting sustainability. The model employs a robust combination of neural networks and gradient boosting decision trees to analyze and predict data points, assessing soil susceptibility to liquefaction during seismic events. Notably, the model achieves high accuracy in predicting soil classifications and N-values, which are critical for evaluating soil liquefaction risk. Validation against an extensive dataset from geotechnical surveys confirms the model’s practical effectiveness. Moreover, the results highlight the transformative potential of AI in enhancing geotechnical risk assessments and improving the resilience of urban areas against natural hazards.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Currently, active and intelligent packaging have been developed to solve the spoilage problem for rich protein foods during storage, especially by adding anthocyanin extracts. In such film system, the antioxidant and antibacterial properties were dramatically increased by adding anthocyanins. The physicochemical properties were enhanced through interactions between active groups in anthocyanins and reactive groups in polymer chains. Additionally, active and intelligent film could monitor the spoilage of rich protein foods in response to pH change. Therefore, this film could monitor the sensory acceptance, and extending the shelf life of rich protein foods simultaneously. In this paper, the structure and functional properties of anthocyanins, the composite actions of anthocyanin extracts and biomass materials, and their reinforced properties of active and intelligent film were discussed. Also, the applications of this film in quality maintenance, shelf-life extension and quality monitoring for fresh meat, aquatic product and milk were summarized. The film that achieves high stability and continuous release of anthocyanins on demand will become an underlying trend in packaging applications for rich protein foods.

There is a noticeable absence of health education among college students. This study aimed to evaluate the extent of general nutrition knowledge among Chinese university students and explore its association with eating attitudes. Data were collected from a group of 273 students in Spring of 2023, using a valid and reliable research instrument consisting of three sections: demographic variables, the General Nutrition Knowledge Questionnaire (GNKQ), and the Eating Attitudes Test (EAT-26). The results were analyzed using SPSS, with correlations and t-tests to examine the relationships between nutritional knowledge and dietary attitudes. Furthermore, the present study employed the Random Forest (RF) algorithm, a machine learning technique, utilizing the Mean Decrease Impurity (MDI) method to investigate the influence of various features on participants' eating attitudes. The findings revealed that Chinese university students had an average accuracy of over 60% in their nutritional knowledge, but their understanding of the relationship between diet and disease still needs improvement. Moreover, male students had significantly lower nutritional knowledge than female students, and there was a positive correlation between nutritional knowledge and parents’ income. The study also found a significant correlation between the level of nutritional knowledge and eating attitudes. RF results indicated that family income level exhibited the most substantial impact on the eating attitudes of the participants. The study highlights the need for nutrition education curriculum developers to focus more on improving students' nutritional knowledge, with particular attention given to male students, low-income individuals, and those with an abnormal BMI.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

This paper proposes an interpretable geometry solution based on the formal language set of text and diagram. Geometry problems are solved by machines, which still poses challenges in natural language processing and computer vision. Significant progress promotes existing methods in the extraction of geometric formal languages. However, the neglect of the graph structure information in the formal language and the lack of further refinement of the extracted language set can lead to the poor effect of the theorem prediction and affect the accuracy in problem solving. In this paper, the formal language graph is constructed by the extracted formal language set and used to theorem prediction by graph convolutional network. So as to better extract the relationship set of diagram elements, an improved diagram parser was proposed. The test results indicate that the improved method has good results in solving the problem with interpretability geometry.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

Under the oxidative stress condition, the small RNA (sRNA) Oxys that acts as essential post-transcriptional regulators of gene expression is produced and plays a regulatory function with the assistance of the RNA chaperone Hfq protein. Interestingly, experimental studies found that the N48A mutation of Hfq protein could enhance the binding affinity with OxyS while resulting in defection of gene regulation. But, how the Hfq protein interacts with sRNA Oxys and the origin of the stronger affinity of N48A mutation are both unclear. In this paper, molecular dynamics (MD) simulations were performed on the complex structure of Hfq and OxyS to explore their binding mechanism. The molecular mechanics generalized Born surface area (MM/GBSA) and interaction entropy (IE) method were combined to calculate the binding free energy between Hfq and OxyS sRNA, and the computational result is in excellent correlation with the experimental result. Per-residue decomposition of the binding free energy revealed that the enhanced binding ability of the N48A mutation mainly comes from the increased van der Waals interactions (vdW). This research explores the binding mechanism between Oxys and chaperone protein Hfq, and revealed the origin of the strong binding affinity of N48A mutation. The results provided important insights on the mechanism of gene expression regulation affected by protein mutations.

The objective of this study was to investigate the liquefaction resistance of chemically improved sandy soils in a straightforward and accurate manner. Using only the existing experimental databases and artificial intelligence, the goal was to make predictions without conducting physical experiments. Emphasis was placed on the significance of data from 20 loading cycles of cyclic undrained triaxial tests to determine the liquefaction resistance and the contribution of each explanatory variable. Different combinations of explanatory variables were considered. Regarding the predictive model, it was observed that a case with the liquefaction resistance ratio as the dependent variable and other parameters as explanatory variables yielded favorable results. In terms of exploring combinations of explanatory variables, it was found advantageous to include all variables as doing so consistently resulted in a high coefficient of determination. The inclusion of the liquefaction resistance ratio in the training data was found to improve the predictive accuracy. In addition, the results obtained when using a linear model for the prediction suggested the potential to accurately predict the liquefaction resistance using historical data.

This paper considers a two-way relay network, where two source nodes exchange messages through several relays in the presence of an eavesdropper, and the channel state information (CSI) of the eavesdropper is imperfectly known. The amplify-and-forward relay protocol is used and the relay beamforming weights are designed. The model is built up to minimize the total relay transmit power while guaranteeing the quality of service at users and preventing the eavesdropper from decoding the signals. Due to the imperfect CSI, a semi-infinite programming problem is obtained. An algorithm is proposed to solve the problem, and the iterative points are updated through the linesearch technique, where the feasibility are preserved during iterations. The optimality property is analyzed. The obtained subproblems are quadratic constrained quadratic programming problems, either with less than $4$ constraints or with only one variable, which are solved optimally. Simulation results demonstrate the importance of the proposed model, and imply that the proposed algorithm is efficient and converges very fast, where more than 85% of the problems are solved optimally.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

The availability of multiple sequenced genomes from a single species made it possible to explore intra- and inter-specific genomic comparisons at higher resolution and build clade-specific pangenomes of several crops. The pan-genomes of crops constructed from various cultivars/accessions, landraces, and wild ancestral species represent a compendium of genes and structural variations and allow researchers to search for the novel genes and alleles that were inadvertently lost in domesticated crops during the historical process of crop domestication or in the process of extensive plant breeding. Fortunately, many valuable genes and alleles associated with desirable traits like disease resistance, abiotic stress tolerance, plant architecture, and nutrition qualities exist in landraces, ancestral species, and crop wild relatives. The novels genes from the wild ancestors and landraces can be introduced back to high-yielding varieties of modern crops by implementing classical plant breeding, genomic selection, and transgenic/gene editing approaches. Thus, pan-genomic represents a great leap in plant research and offers new avenues for targeted breeding for mitigating the impact of global climate change. Here we summarize the tools used for pangenome assembly and annotations, web-portals hosting plant pangenomes. Furthermore, we highlight a few discoveries made in crops using the pan-genomic approach and its future potential.

BACKGROUND: Qu-aroma is a critical quality indicator for medium-high temperature Daqu (MT-Daqu), significantly influencing the aroma profile of strong-aroma Baijiu (SAB). SAB is produced across various regions in China, each with unique environmental conditions and production techniques. These regional differences are likely to cause variations in the Qu-aroma of MT-Daqu. Despite this, comprehensive research on the variations in Qu-aroma across different regions has been lacking. This study aims to address this gap by utilizing Gas Chromatography-Olfactometry-Mass Spectrometry (GC-O-MS) and electronic nose (E-nose) technology, combined with sensory evaluation, to analyze the differences in Qu-aroma characteristics and volatile compound profiles of MT-Daqu from seven distinct production areas.RESULTS: Sensory analysis identified seven broad aroma categories and 25 specific aromas characterizing the Qu-aroma of MT-Daqu samples. Chen aroma and roasted aroma were notably more prevalent in MT-Daqu samples from Sichuan compared to those from other regions (P < 0.05), while the fermentation aroma was less prominent in Sichuan samples. In total, 123 volatile compounds were detected in MT-Daqu, with 46 classified as aroma-active compounds. Among these, 21 aroma-active compounds were identified as markers distinguishing Sichuan MT-Daqu from those produced in non-Sichuan regions, showing significant differences in their concentrations (P < 0.05). Additionally, six major aroma-active compounds-ethyl isovalerate, ethyl heptanoate, hexanal, 1-nonanal, (E)-2,4-decadienal, and 2,3-dimethyl-5-ethylpyrazine-were found to significantly contribute to the aroma differences between Sichuan and non-Sichuan MT-Daqu.CONCLUSION: This study delineates the distinct Qu-aroma characteristics of MT-Daqu from various SAB production areas and identifies the aroma-active compounds responsible for these differences. The insights gained from this research offer valuable guidance for optimizing flavor profiles in MT-Daqu production, potentially enhancing the overall quality and regional distinctiveness of the product.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

Gaussian mixture models (GMMs) are powerful tools specifically suited for problems where data distributions are multi-modal. Inspired by Fourier expansion, we propose a concept called GMM expansion to approximate arbitrary densities. A simple learning method is introduced under this framework. Theoretical and numerical analyses are provided to show that densities under GMM expansion are able to approximate arbitrary densities with certain accuracy. The proposed learning algorithm demonstrates better accuracy and time efficiency compared to classic density approximation methods such as the Expectation Maximization (EM) algorithm and Bayesian variational inference (BVI) for Gaussian mixture models. The proposed framework also shows better accommodation of neural networks. Three neural network applications are built to demonstrate its usability. The accuracy of density estimation in neural networks is reported to be significantly improved in one of the applications. Another application shows that latent variables can be easily turned into random variables. This user-friendly method opens up more possibilities in terms of latent manipulation, embedding techniques, and many other potential uses.

In this paper, we design two inertial-type subgradient extragradient algorithms with line-search process for solving the pseudomonotone variational inequality problems (VIPs) and common fixed-point problem (CFPP) of finite Bregman relatively nonexpansive mapping and a Bregman relatively demicontractive mapping in p-uniformly convex and uniformly smooth Banach spaces, which are more general than Hilbert spaces. Under mild conditions, we derive weak and strong convergence of the suggested algorithms to a common solution of the VIPs and CFPP, respectively. Additionally, an illustrated example is furnished to back up the feasibility and implementability of our proposed methods.

The log data generated during the operation of a software system contains information about the system, and using logs for anomaly detection can detect system failures in a timely manner. Most of the existing log anomaly detection methods are specific to a particular system, have cold start problems, and are sensitive to updates in log format. In this paper, we propose a log anomaly detection method LogBD based on pre-training model and domain adaptation, which uses the pre-training model BERT to learn the semantic information of logs, and can solve the problems caused by multiple meaning words and log statement updates. An anomaly detection method LogBD based on distance to determine anomalies is constructed based on domain adaptation, using TCN networks to extract common features of different system logs and map them to the same hypersphere space. Finally, experiments are conducted on two publicly available datasets to evaluate the method, and the experimental results show that the method can better solve the log instability problem and has some improvement in the cross-system log anomaly detection effect.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

The research on the distribution of rural buildings is one of the fundamental works of urban-rural development in Vietnam. Adopting Mask R-CNN deep learning framework and collecting sub-meter remote sensing images, this research used a remote sensing interpretation model of rural buildings trained based on East Asian characteristics of rural buildings and successfully recognized about 2.87 million rural buildings in 34 Vietnamese provincial administrative districts with a total area of rural buildings of 2,492 million square meters. The reliability of the identification results was verified by manual detection and quantitative statistics, and a multi-scale database of rural buildings in Vietnam based on individual rural buildings was created. Based on the database, this paper analyzes the distribution characteristics of rural buildings and summarizes characteristics of rural buildings distribution at the country, regional, and provincial scales. The identification results lay the foundation for the next study of urban-rural relations in Southeast Asia and the construction of a basic database on villages.

Warming-induced drought stress and El Nino associated summer precipitation failure are responsible for increased forest fire intensities of tropical and temperate forests in Asia and Australia. However, both effects are unclear for boreal forests, the largest biome and carbon stock over land. Here we combined fire frequency, burned area and climate data in the Altai boreal forests, the southmost extension of Siberia boreal forest into China, and explored their link with ENSO (El Nino and South Oscillation). Surprisingly, both summer drought severity and fire occurrence have shown significant (P&lt;0.05) teleconnections with La Nina events of the previous year, and therefore provide an important reference for forest fire prediction and prevention in Altai. Despite a significant warming trend, the increased moisture over Altai has largely offset the effect of warming-induced drought stress, and lead to an insignificant fire frequency trend in the last decades, and largely reduced burned area since the 1980s. The reduced burned area could also benefit from the fire suppression efforts and greatly increased investment in fire prevention since 1987.

Previous studies on the water-energy nexus mainly focused on the calculation and comparison of resource consumption at the national or regional level, lacking interprovincial sector-sector transfer analysis. In this study, the intensity of water and energy consumption of various sectors in China were calculated, the key nodes and paths of resource networks were identified, and countermeasures for resource conservation were proposed from the new perspective of the “dual saving” and “bidirectional saving” of water and energy. The results showed that the metallurgical industry (Me) in Jiangsu and the chemical industry (Ch) in Hebei and Jiangsu had high node strength in the water and energy network and were key sectors in China with “dual saving” effects of water and energy. The construction industry, Ch, Me in Jiangsu, electricity and hot water production and supply industry in Beijing, and Me in Hebei had high node strength in the water-related energy network and energy-related water network, significantly supporting the “bidirectional saving” effect of water and energy in China. The electrical equipment industry (El) in Jiangsu→El in Zhejiang, El in Zhejiang→El in Shanghai frequently appeared in key paths, which could effectively reduce the resource consumption of the entire network.

China faces a persistent deficiency in feed protein resources. Enhancing the utilization efficiency of indigenous feed protein resources emerges as a viable strategy to alleviate the current deficit in protein feed supply. Corn gluten meal (CGM), characterized by high proportion of crude protein and glutamine, is predominantly employed in animal feed. Nonetheless, the water-insolubility of CGM protein hampers its protein bioavailability when utilized as feed material. This study aimed to augment protein bioavailability, liberate glutamine peptides from CGM, and produce gluta-mine-enriched CGM fermented feed. We executed a co-fermentation protocol using Bacillus subtilis A5, Lactobacillus 02002, and acid protease to generate the CGM fermented feed. Subsequent in vivo experiment with broilers were conducted to assess the efficacy of the fermented product. Findings revealed that the soluble protein, glutamine, small peptides, and lactic acid contents in the fer-mented feed increased by 69.1%, 700%, 47.6%, and 125.9%, respectively. Incorporating CGM fermented feed into the diet markedly enhanced the growth performance and intestinal health of broilers, positively modulated the cecal microbiota structure, and augmented the population of beneficial bacteria, specifically Lactobacillus. These results furnish both experimental and theoretical foundations for deploying CGM fermented feed as an alternative protein feed resource.

This article explored how some state policies on rehabilitation, protection and utilization of mangroves are implemented at two locals; namely, Ca Mau provice and its sub-unit Ngoc Hien District as well as Ho Chi Minh City and its sub-unit Can Gio District and what are considered as emgerging issues in the implementation process. The study employed mixed research methods including document and thematic analysis, in-depth interviews, and group discussion. The findings showed that state policies would be adapted through the ways in which these two locals manage to silmultaneously orient their work toward accommodating the madates placed upon them and cope with the reality of socio-economic difficulties at their levels. The findings also showed some issues that need to consider addressing; namely, locals’ struggles to fill the gaps between written and implemented policies in mangrove rehabilitation, conflict among sectors and stakeholders in mangrove utilization and protection, problems in guaranteeing adequate budget for in-need-locals, inconsistence in policies on "forest: water surface” ratio in mangrove-shrimp farm, and unintended consequences in forest thinning and exploitation regimes. Based on the finding analysis, the articles discussed lessons learned from the policy implementation process on mangrove rehabilitation, management and forest allocation to household in the south of Vietnam.

Since the COVID-19 caused by SARS-CoV-2 break out in Wuhan China from Dec. 2019, it has spread to hundreds of countries up to now. Scientists from all over the world have paid tremendous efforts to research and try to control the disease. Previous studies suggested that some of the wild animals could be intermediate hosts between humans and origination of SARS-CoV-2, and some companion animals of humans can be infected by SARS-CoV-2, which raised our curiosity about cross-infection of SARS-CoV-2 between animals and humans. Thus, we select some kinds of animals that might have contact with humans to estimate the susceptibility to SARS-CoV-2 in different animals by evolutionary analysis of their receptors for SARS-CoV-2. The results show that some companion animals of the Felidae family like the cat has a higher infection possibility while the species of the Rodent family like the rat and mouse having close contact with humans show an opposite result, which consist with recent animal experiments and researches. These should raise concerns about cross-infection between human and companion animals or animals having close contact with humans which might turn animals into depositaries of the coronavirus even after control of SARS-CoV-2 spreading and cause second or more waves of infections after social reopening. Another side of our results stands by the opinion that bioinformatic analysis can be consistent with experiments in some respects so that we can prevent unnecessary sacrifice of laboratory animals in future experiments.

The high flammability and lack of charrability of polystyrene (PS) pose significant limitations on its broader applications. Therefore, there is an urgent need for a straightforward and efficient method for the synthesis of flame-retardant PS, which still poses a considerable challenge. In this study, we present an efficient approach to enhance the flame-retardant properties of PS through direct phosphorylating aromatic C(sp2)-H bonds using commercially available and inexpensive manganese catalyst. A range of phosphonates served as reactive substrates to enable a tunable degree of polymer functionalization. The corresponding phosphorylated PS specimens were determined by means of 1H NMR, 31P NMR, FTIR spectroscopy and GPC. Microscale combustion calorimetry (MCC) tests indicate that this protocol indeed enhances the flame-retardant performance of PS. Moreover, other advantages associated with the incorporation of the phosphonate group have been observed, including improved thermal resistance and wettability. This cost-effective strategy of Mn-catalyzed C-H can also be utilized to directly obtain phosphonate modification of waste foamed PS and styrene acrylonitrile copolymer, providing a new method for the purpose of recycling and upgrading PS plastics.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Multi-Object Tracking (MOT) is a key technology for Unmanned Aerial Vehicles (UAVs). Traditional tracking-by-detection methods firstly employ an object detector to retrieve targets in each image and then track them based on a matching algorithm. Recently, the popular multi-task learning methods has been dominating this area since they can detect targets and extract Re-Identification (Re-ID) features in a computationally efficient way. However, the detection task and the tracking task have conflicting requirements on image features, leading to the poor performance of the joint learning model compared to separate detection and tracking methods. The problem is more severe when it comes to UAV images due to the presence of irregular motion of large number of small targets. In this paper, we propose a balanced Joint Detection and Re-ID learning (JDR) network to address the MOT problem in UAV vision. To better handle the non-uniform motion of objects in UAV videos, the Set-Member Filter is applied which describes object state as a bounded set. An appearance matching cascade is then proposed based on target state set. Furthermore, a Motion-Mutation module is designed to address the challenges posed by the abrupt motion of UAV. Extensive experiments on the VisDrone-MOT2019 dataset demonstrate that our proposed model, termed as SMFMOT, outperforms state-of-the-arts by a large margin and achieves superior performance on the MOT tasks in UAV videos.

Detection of early stage corrosion on slender steel members is crucial for preventing buckling failures of steel structures. An active photoacoustic fiber optic sensors (FOS) system has been reported for early stage steel corrosion detection of steel plates and rebars using surface ultrasonic waves. The objective of this paper is to investigate the surface corrosion/rust detection problem on steel rods using numerically simulated surface ultrasonic waves. The finite element method (FEM) is applied in simulating the propagation of ultrasonic waves on steel rod models. Transmission mode of damage detection is adopted, in which one source (transmitter) and one sensor (receiver) are considered. In this research, radial displacements at the receiver were simulated and analyzed by short-time Fourier transform (STFT) for detecting, locating, and quantifying a surface rust located between the transmitter and the receiver. From our time domain and frequency domain analyses, it is found that the presence, location, and dimensions (length, width, and depth) of surface rust can be estimated by ultrasonic waves propagating through the surface rust.

The stability of the filling roof as an important bearing unit in the stope of the access stope in the filling mining method is of great significance to guarantee the safe and efficient production of the mine. Arrangement of mining approach in downward cemented filling stope is the key factor af-fecting stability of filling body roof. Based on combination of laboratory test, theoretical analysis and numerical simulation, the influence of different mining approach arrangement on stability of filling body roof is analyzed. The weak filling surface is formed between adjacent mining paths. The mechanical strength of the weak filling surface is significantly reduced by laboratory experiments. The relationship between distribution of the weak filling surface, azimuth angle and stability of filling roof is further studied by numerical simulation. The results show that the stability of the filler roof is the best when the upper and lower stratified mining approach is arranged vertically.

With global warming, arable land in boreal regions is tending to expand into high latitude regions in the northern hemisphere. This entails certain risks; such that inappropriate management could result in previously stable carbon sinks becoming sources. Agroecological models are an important tool for assessing the sustainability of long-term management, yet applications of such models in boreal zones are scarce. We collated eddy-covariance, soil climate and biomass data to evaluate the simulation of GHG emissions from grassland in eastern Finland using the process-based model DNDC. We simulated gross primary production (GPP), net ecosystem exchange (NEE) and ecosystem respiration (Reco) with fair performance. Soil climate, soil temperature and soil moisture at 5 cm were excellent, and soil moisture at 20 cm was good. However, the model overestimated NEE and Reco following crop termination and tillage events. These results indicate that DNDC can satisfactorily simulate GHG fluxes in a boreal grassland setting, but further work is needed, particularly in simulated second biomass cuts, the (>20 cm) soil layers and model response to management transitions between crop types, cultivation, and land use change.

As e-commerce services and Internet technology have rapidly developed in recent years, many services and applications integrating these technologies can now be completed online. These commercial activities include online auctions, online ticketing and online payments. The client shops from the store online, andthe store delivers the goods to the client. The goods can be divided into digital products without entities, as well as actual entities. If it is a physical product, the store will deliver the package to the client through itslogistics. However, there have been many cases of switched goods purchased by clients in recent years. Earlier, some scholars proposed a security mechanism with a subliminal channel for E-cash and digital content. Only the sender and the receiver would know that the secret information was hidden in the signature. So the privacy of this subliminal message couldbe ensured. We apply this concept to the logistics environment to design secure logistics architecture with subliminal messages. The client can check the subliminal message of the received package, and know whether the package has been switched by malicious people. In addition, the proposed scheme also applies sensor technology;the client can check the GPS location, the temperature and humidity at any time during the delivery process. So intelligent logisticswouldthereby be achieved. This paper proposes an intelligent and secure package sensoring logistics system based on a subliminal channel. The proposed architecture uses the related mechanisms tosolve the problems of a logistics system, including how to achieve mutual authentication, data integrity, anti-switch package, package location and status tracing, resisting replay attacks, forward and backward secrecy, and non-repudiation issues.

Nanoparticle-assisted polymerase chain reaction (nanoPCR) is a novel method for rapid detection of pathogens. A sensitive and specific multiple nanoPCR assay was developed for simultaneous detection of three subgroups avian leucosis virus (ALV). In this study, three pairs of primers that were designed based on gp85 gene sequences of subgroup A, B and J, optimizations were carried out for better performance of the nanoPCR assay and remarkably improved the detection limit of the assay. The detection limit of the assay was 101copies/μl, which was 100-fold more sensitive than conventional PCR assays. The nanoPCR assay amplified the specific 336 bp, 625 bp and 167 bp fragments of ALV-A, -B and –J respectively and no cross-reactivity were found with the genomic DNA or cDNA of Newcastle disease virus, avian infectious laryngotracheitis virus, Marek's disease virus, infectious bronchitis vaccine, infectious bursal disease virus and avian encephalomyelitis Virus. To evaluate the detection ability of the assay, 186 clinical samples were detected by nanoPCR and the detection results were further confirmed by sequencing. The sequencing results were 100% in coincidence with the nanoPCR detection results, suggesting the possibility of clinical application of the newly developed nanoPCR assay. Taking all the results together, a highly specific and sensitive nanoPCR was successfully developed, which could be useful for rapid diagnosis of ALV in poultry farming.

Medium-deep Borehole Heat exchanger (MBHE) has been widely paid attention for building heating. In order to avoid the thermal interference of adjacent MBHEs, temperature distribution characteristics of medium-deep rock-soil was investigated in this work. The evolution on maximum rock-soil thermal affected radius (MTAR) in full life cycle was further analyzed. The results showed that the rock-soil thermal affected area (RTAA) continuously expands in both radial and vertical directions during a heating season. Several factors of thermal extraction load, fluid velocity, geothermal gradient and pipe length have main impacts on the RTAA in vertical direction. Rock-soil thermal conductivity affects the RTAA in both radial and vertical directions. In non-heating season, temperature difference of rock-soil in radial direction dominates the temperature recovery in the first year while geothermal flow nearly dominates temperature recovery after 20 years. The thermal affected radius (TAR) in the 30 th year could be determined as an effective MTAR in full life cycle. In order to decrease installed distance of adjacent MBHEs, a new well layout form by deflecting borehole was proposed. The recommended deflection angle is equal to or larger than 4 times TAR angle. This work provides scientific reference for promoting application of multiple MBHE arrays.

Link prediction is to complete the missing links in the network or to predict the generation of new links according to the current network structure information, which is very important for mining and analyzing the evolution of the network such for construction and analysis of logical architecture in 6G network. Link prediction algorithms based on node similarity need predefined similarity functions, which is highly hypothetical and only applies to specific network structures without generality. To solve this problem, this paper proposes a link prediction algorithm based on the subgraph of the target node pair. In order to automatically learn the graph structure characteristics, the algorithm firstly extracts the h-hop subgraph of the target node pair, and then predicts whether the target node pair will be linked according to the subgraph. Experiments on seven real data sets show that the link prediction algorithm based on target node pair subgraph is suitable for various network structures and superior to other link prediction algorithms.

The heat release response of the flame to acoustic excitation is a critical factor for understanding combustion instability. In the present work, the nonlinear heat release response of a methane-air non-premixed flame to the low frequency acoustic excitations is experimentally investigated. The flame describing function (FDF) was measured based on the overall CH* chemiluminescence intensity and the velocity fluctuations obtained by two-microphone method. The CH* chemiluminescence images and the schlieren images were analyzed to reveal the mechanism of nonlinear response. The excitation frequency ranges from 10Hz to 120Hz. The forced relative velocity fluctuation amplitude ranges from 0.10 to 0.50. The corresponding flame Strouhal number (Stf) ranges from 0.43 to 4.67. The study has shown that the flame length responds more sensitively to changes in excitation amplitude when subjected to relatively high frequency excitations. The normalized flame length (Lf/D) decreases from 3.79 to 2.37 with the increase of excitation amplitude at excitation frequency of 100Hz. The number of oscillation zones along the flame increases with increasing excitation frequency, which is consistent with the increase of the Stf. The low-pass filtering characteristic of FDF is caused by the dispersion of multiple oscillation zones, as well as the cancellation effect of the adjacent oscillation zones under relatively high frequency excitation. The cancellation effect of the positive and negative oscillation zones with various Stf is main mechanism for the local gain peak and valley. When two adjacent oscillation regions have approximate amplitudes, the overall phase-lag becomes more sensitive to changes in excitation frequency and amplitude. This sensitivity leads to nonlinear anomalous changes in the phase-lag near the frequency corresponding to the gain valley. The calculated disturbance convection time is consistent with the measured time delay in the short flame scenario. Future research is necessary to establish whether the observed agreement occurs due to the oscillation zone consistently occurring proximate to the flame's center of mass, coupled with a precise determination of the average convective velocity.

Based on data from the Yunnan Province farm household survey, we examine the effect of rural land rights policy on farmers’ income. The regression results show that right significantly raises the total income of farmers, with farm income serving as the primary source of total income. After performing numerous robustness tests, using instrumental variables to handle endogeneity and arriving at the same conclusion, the result is still valid. According to the heterogeneity analysis, in the sample of households with long-term migrant workers, the confirmation of rural land rights significantly increases total and nonfarm income while decreasing farm income. Furthermore, total income includes nonfarm income, which reflects the effect of different farmers' optimal labor allocation based on the external market environment. According to the impact mechanism anal-ysis, right can increase farmers' total income by promoting land transfer, and farmers in less developed areas are more willing to increase their income by land transfer out.

Wi-Fi based localization has become one of the most practical methods for mobile users in location-based services. However, due to the interference of multipath and high-dimensional sparseness of fingerprint data, the localization system based on received signal strength (RSS) is hard to obtain high accuracy. In this paper, we propose a novel indoor positioning method, named JLGBMLoc (Joint denoising auto-encoder with LightGBM Localization). Firstly, because the noise and outliers may influence the dimensionality reduction on high-dimensional sparseness fingerprint data, we propose a novel feature extraction algorithm, named joint denoising auto-encoder (JDAE), which reconstructs the sparseness fingerprint data for a better feature representation and restores the fingerprint data. Then, the LightGBM is introduced to the Wi-Fi localization by scattering the processed fingerprint data to histogram, and dividing the decision tree under leaf-wise algorithm with depth limitation. At last, we evaluated the proposed JLGBMLoc on UJIIndoorLoc dataset and Tampere dataset, experimental results show that the proposed model increases the positioning accuracy dramatically comparing with other existing methods.

An adaptive spatial clustering (ASC) algorithm is proposed in this present study, which employs sweep-circle techniques and a dynamic threshold setting based on the Gestalt theory to detect spatial clusters. The proposed algorithm can automatically discover clusters in one pass, rather than through the modification of the initial model (for example, a minimal spanning tree, Delaunay triangulation or Voronoi diagram). It can quickly identify arbitrarily-shaped clusters while adapting efficiently to non-homogeneous density characteristics of spatial data, without the need of prior knowledge or parameters. The proposed algorithm is also ideal for use in data streaming technology with dynamic characteristics flowing in the form of spatial clustering in large data sets.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

SARS-CoV2 (corona virus) has spread globally at an unprecedented rate; so far, increasing SARS-CoV2-infected individuals have been identified. Although the situation in China is improving and is currently under control, the outbreak in other countries and its pandemic management is only beginning to develop. Based on 154 SARS-CoV2 genome sequence analyses, we used receptor–ligand docking to identify one potential point mutation (V354F) on the spike structure which enhances spike binding to ACE2 receptors underlying potential super infection. Importantly, the V354F site on spike S1 had been identified in 5/10 infected French patients living in Paris, who sharing 100% identical SARS-CoV2 genomes. With Covid-19 cases increasing rapidly in France that could lead to a new explosion, we suggest that the French government should identify all potential super spreaders and treat them accordingly. In summary, our study provides on of the measures to avoid the potential second worldwide explosion of SARS-CoV2.

Objective: This research was aimed to estimate the anti-fatigue effects of arecoline and elucidate its underlying mechanisms using a murine model of central fatigue precipitated by sleep deprivation (SD). Methods: Seventy-two male C57BL/6 mice were randomly allocated into six groups: a control group, a SD-induced fatigue model group, a group receiving Rhodiola Rosea capsules (2.5 mg/kg), and arecoline groups administered low, medium, and high doses (10, 20, and 40 mg/kg, respectively). Following 28 days of continuous administrations, the effects of arecoline on the mouse fatigue-related behaviors was assessed by the behavioral tests, including grip strength, rotarod performance, and weight-bearing swimming endurance. Enzyme-linked immunosorbent assays (ELISAs) were utilized to measure the levels of the relevant biochemical markers. Western blotting was employed to quantify the expression of nuclear factor erythroid 2-related factor (Nrf2), Kelch-like ECH-associated protein 1 (Keap1), heme oxygenase 1 (HO-1), sequestosome-1 (p62), and NADPH quinone oxidoreductase 1 (NQO1) in the gastrocnemius muscle. Results: Arecoline administration notably enhanced grip strength, delayed the onset of fatigue as evidenced by extended latencies in rotarod tests, and increased the duration of weight-bearing swimming in mice. In the elevated plus maze, arecoline significantly reduced both the number of entries and the total distance traveled in the open arms. Arecoline markedly decreased serum levels of creatine kinase, blood urea nitrogen, lactate dehydrogenase, triglycerides, and cholesterol, while elevated total testosterone, lactate dehydrogenase, and immunoglobulin G levels. Furthermore, it significantly increased superoxide dismutase(SOD), catalase(CAT), and glutathione peroxidase activity in the gastrocnemius muscle, reduced malondialdehyde levels, augmented hippocampal SOD and CAT activity, and elevated glycogen stores in both liver and muscle tissues. Neurotransmitter levels were significantly increased, cytokine levels were markedly reduced, and the expression of Nrf2, Keap1, NQO1, p62, and HO-1 in brain tissue was significantly upregulated. Conclusion: The current study for the first time demonstrated that arecoline has significant anti-fatigue activity, and its mechanism of action is related to elevate the levels of glucose and lipid metabolism, relieve oxidative stress damage, inhibit neuroinflammatory response, regulate neurotransmitter levels and Keap1/Nrf2/HO-1 signaling pathway. The current study provides a new insight into the potential of arecoline in prevention and improvement of fatigue.

Two secondary waste materials, municipal incinerator bottom ash (MIBA) and sewage sludge ash (SSA), were mixed with clay for ceramic manufacturing in this study. Specimens with 5 different MIBA replacement amount of 0%, 5%,10%, 15%, and 20%(wt) and 3 different SSA replacement amount of 0%, 10%, and 20%(wt) were prepared and then a series of tests and analysis were conducted to investigate how the two materials affect the quality of the final product and to what extent. It concludes that a mix with up to 20% of SSA and 5% of MIBA could result in quality tiles complying with specifications for interior or exterior flooring applications at certain kiln temperatures.

Seasonal precipitation variance significantly alters soil water content, potentially inducing water stress and affecting plant transpiration in semiarid deserts. This study explored the effects of environmental variables and hydraulic conductance on whole-tree transpiration (ET) in Mongolian pines (Pinus sylvestris var. mongolica) across different forest stages in the semiarid deserts of northern China. We measured ET using sap flow in mature (MMP), half-mature (HMP), and young (YMP) Mongolian pine plantations. Measurements included soil-leaf water potential difference (ΔΨ), atmospheric conditions, and soil moisture contents on sunny days, both in dry and wet periods. Seasonally variable rainfall distinctly affected soil moisture, correlating ET with photosynthetically active radiation (PAR) and vapor pressure deficit (VPD). Notable nocturnal sap flow occurred during the growing season. During the dry periods, both stomatal and hydraulic conductance influenced ET, whereas during the wet periods, stomatal conductance primarily regulated it. Discrepancies between predicted and measured ET were noticed: compared to the predicted ET, measured ET was lower during dry periods while higher during wet periods. Hydraulic conductance (KT) increased with tree height (H) and ΔΨ, although tall trees exhibited lower KT rates, suggesting that hydraulic compensation had occurred. This compensation, observed between 11:00 and 13:00, aligned with increased hydraulic resistance during dry periods. Decreasing hydraulic conductance intensified leaf water stress in dry periods, especially during the time when PAR and VPD were heightened, potentially increasing stomatal sensitivity to drought, promoting water conservation and plant survival. A linear relationship between predawn and midday leaf water potentials was noticed, indicating extreme anisohydric behavior across forest stages during both dry and wet periods. Although both stomatal and hydraulic conductance influenced ET during the dry period, MMP and YMP were more susceptible to drought conditions. Understanding these dynamics could help evaluate semiarid desert ecological functions for water conservation amidst uneven seasonal precipitation in Northern China.

In a p-uniformly convex and uniformly smooth Banach space, let the pair of variational inequality and fixed point problems (VIFPPs) consist of two variational inequality problems (VIPs) involving two uniformly continuous and pseudomonotone mappings and two fixed point problems implicating two uniformly continuous and Bregman relatively asymptotically nonexpansive mappings. This article designs two parallel subgradient-like extragradient algorithms with inertial effect for solving this pair of VIFPPs, where each algorithm consists of two parts which are of symmetric structure mutually. Under mild registrations, we prove weak and strong convergence of the suggested algorithms to a common solution of this pair of VIFPPs, respectively. Lastly, an illustrative example is furnished to verify the applicability and implementability of our proposed approaches.

Objective: To explore the hot spots and development trends of community public health research. Methods: The literature related to this topic was searched in CNKI and PubMed databases, and the trend map of the number of articles was drawn according to the obtained data. The included literature were analyzed with Vosviewer software for keyword and author co-occurrence, and CiteSpace 6.3.R1 Basic software was used for mechanism co-occurrence, key emergence and clustering analysis, and timeline distribution map drawing. Results: 189 Chinese literature and 77 English literature were selected. The Chinese literature focused on “community public health service, emergency management, and community governance”, and the research trend was “community public health emergency management and community governance”; English literature focuses on “nursing education, health education, human qualitative research”. Conclusion: Although the Chinese and English literature shows that scholars in this field have different emphases, the primary community health is the key and difficult point to realize the national public health service project, and improving the basic public health service in the primary community is related to the health of all the people, so it is very important.

The application of Explainable AI (XAI) to improve understanding of complex non-linear SST teleconnections and gain predictive skills is at the frontier of climate research. In this study, we attempt to refine the applications of XAI advancements to ENSO prediction by including SSTA in the western North Pacific (WNP) as a precursor. Our analyses indicate that the baseline accuracy increases from the 60% threshold previously reported for ENSO to &gt;85% for moderate warm, cold, and neutral ENSO states one year in advance when WNP SSTA is included. Precision increases to over 90% for higher magnitude El Niños and La Niñas. Experiments conducted at 4-year lead times yield a strong WNP SSTA signal. A moderate SSTA signal is observed at 3-year lead time with no predictability; however, predictability spikes to over 80% when stratospheric zonal winds are included with WNP SSTA. While additional scientific work is required to make robust connections between XAI and dynamical processes, our results demonstrate a potential to improve long term predictability of ENSO through the ability of XAI in capturing SST patterns evolving at extended spatial and temporal scales.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

2-Methylquinazolin-4(3H)-one was prepared by reaction of anthranilic acid, acetic anhydride and ammonium acetate. The reaction of 2-methylquinazolin-4(3H)-one with N-aryl-2-chloroacetamides in acetone in the presence of potassium carbonate gave nine N-aryl-2-(2-methyl-4-oxoquinazolin-3(4H)-yl)acetamide compounds. The structures of these compounds were elucidated on the basis of their IR, 1H-NMR, 13C-NMR and HR-MS spectral data. These synthesized compounds containing the 2-methyl-3,4-dihydroquinazolin-4-one moiety exhibited excellent activity against Aedes aegypti mosquito larvae with LC50 values in the range of 2.085-4.201 μg/mL after 72 h exposure. Interestingly, these compounds did not exhibit toxicity to the non-target organism Diplonychus rusticus. In silico molecular docking revealed acetylcholine binding protein (AChBP) and acetylcholinesterase (AChE) to be potential molecular targets. These data indicated the larvicidal potential and environmental friendliness of these N-aryl-2-(2-methyl-4-oxoquinazolin-3(4H)-yl)acetamide derivatives.

YG-13A represents the highest level of Chinese SAR satellites to date. In this paper, we report on experiments conducted to improve and validate ranging accuracy with YG-13A. We analyze the error sources in the YG-13A ranging system, such as atmospheric path delay, and transceiver channel delay. A real-time atmospheric delay correction model is established to calculate the atmospheric path delay, considering the troposphere delay and ionosphere delay. Six corner reflectors (CRs) were set up to ensure the accuracy of validation methods. Pixel location accuracies of up to 0.479-m standard deviation can be achieved after a complete calibration. We further demonstrate that the adjustment of the CRs can cause a marginal loss of ranging precision. After eliminating this error, the ranging accuracy is improved to 0.237 m. For YG-13A, a single frequency GPS receiver is used and the orbital nominal accuracy is 0.3 m, which is the biggest factor restricting its ranging accuracy. Our results show that the ranging accuracy of YG-13A can achieve decimeter-level, which is lower than centimeter-level accuracy with TerraSAR-X loading a dual frequency GPS. YG-13A has great convenience in terms of access to control points and target location that does not depend on ground equipment.

Infrared small target detection (ISTD) plays a crucial role in both civilian and military applications. The detection of small targets against dense cluttered backgrounds remains a challenging task, requiring the collaboration of false alarm source elimination and target detection. Existing approaches primarily focus on modeling targets while often neglecting false alarm sources. To address this limitation, we propose a Target and False Alarm Collaborative Detection Network to leverage the information provided by false alarm sources and the background. Firstly, we introduce a False Alarm Source Estimation Block (FEB) that estimates potential interferences present in the background by extracting features on multiple scales and employing stepwise upsampling for feature fusion. Subsequently, we propose a framework that employs multiple FEBs to eliminate false alarm sources across multiple scales. Finally, a Target Segmentation Block (TSB) is introduced to accurately segment the targets to produce the final detection result. Experiments on public datasets demonstrate that, compared to other methods, our model achieves high accuracy in segmenting targets while being able to extract false alarm sources which can be used for further studies.

Soil enzyme activity can be affected by both production and degradation, as enzymes can be degraded by proteases. However, the impact of nutrient addition on enzyme activity is often solely attributed to changes in enzyme production without fully considering degradation. Here, we demonstrated that the activities of β-1,4-glucosidase (BG), β-D-cellobiohydrolase (CBH), β-1,4-Xylosidase (BX), and β-1,4-N-acetyl-glucosaminnidase (NAG) were comparable in nitrogen (N) and phosphorus (P) fertilized soils and the unfertilized control under field conditions, but the reduction in activity was substantially greater in the fertilized soils during short-term laboratory incubation. The results show that the interruption of the natural, continuous supply of organic matter or non-soil microbial-derived enzymes, which typically occurs under field conditions, leads to a more significant reduction in apparent enzyme activities in fertilized soils compared to unfertilized control. This may be attributed to the higher abundance of protease in fertilized soils, resulting in faster enzyme degradation. Interestingly, P fertilization alone did not have a similar effect, indicating that N fertilization is likely the main cause of the larger decreases in enzyme activity during incubation in fertilized soils compared to unfertilized control soils, despite our study site being poor in P and rich in N. These findings highlight the importance of considering enzyme degradation when investigating material dynamics in forest ecosystems, including the impact of nutrient addition on enzyme activity, as enzyme production alone may not fully explain changes in apparent enzyme activity.

In this paper, a distributed algorithm is proposed to solve a consensus convex optimization problem. It is a Jacobi-proximal alternating direction method of multipliers with a damping parameter $\gamma$ in the iteration of multiplier. Compared with existing algorithms, it has the following nice properties: (1) The restriction on proximal matrix is relaxed substantively, thus alleviating the weight of the proximal term. Therefore, the algorithm has a faster convergence speed. (2) The convergence analysis of the algorithm is established for any damping parameter $\gamma\in(0,2]$, which is larger ones in the literature. In addition, some numerical experiments and an application to a logistic regression problem are provided to validate the effectiveness and the characteristics of the proposed algorithm.