Acrylamide (AA), a molecule which potentially increases the risk of developing cancer, is easily formed in food rich in carbohydrates, such as biscuits, wafers and breakfast cereals, at temperatures above 120 °C. Thus, it is eminent the need to detect and quantify the AA content in processed foodstuffs, in order to delineate the limits and mitigation strategies. This work reports the development and validation of a high-resolution mass spectrometry-based methodology for identification and quantification of AA in specific food matrices of biscuits, by using LC-MSⁿ with electrospray ionization and Orbitrap as mass analyser. The developed analytical method showed good repeatability (RSD_r 11.1%) and 3.55 μg kg^-1 and 11.8 μg kg^-1 as limit of detection (LOD) and limit of quantification (LOQ), respectively. The choice of multiplexed targeted-SIM mode (t-SIM) for AA and AA-d3 isolated ions provided enhanced detection sensitivity, as demonstrated in this work. Results for AA concentration obtained vary between 323.7 and 2056.1 μg kg^-1. During baking an increase in AA concentration was observed, as well as between samples taken from different areas of the baking oven. Statistical processing of data was performed in order to compare the AA levels with several production parameters, such as time/cooking temperature, placement on the cooking conveyor belt, color and moisture for different biscuits. The composition of the raw materials was statistically the most correlated factor with the AA content when all samples are considered. The statistical treatment presented herein enables an important prediction of factors influencing AA formation in biscuits contributing for putting in place effective mitigation strategies.

Sustainability, particularly in construction materials, has been a subject of growing interest. Civil construction is one of the industries where more materials are consumed, which leads to high energy consumption and CO2 emissions. The production of cement, especially clinker is largely responsible for these problems. As a solution, new materials emerge, which do not require much energy for their production, which are the alkaline cements, specifically the geopolymers. Geopolymers are inorganic polymers obtained by the alkaline activation of aluminosilicate precursors. In the present study geopolymers were developed with low grade kaolin (as a precursor) from a Portuguese company. The development of these geopolymers will be, due to their properties, a good solution for rehabilitation of earth buildings, especially in adobe. The development of these geopolymers is also a contribution to the sustainability of kaolin exploitations as it opens new markets for the low grade kaolins, presently not easily commercialized. As mechanical strength of adobe materials ranges in literature from 0.6 to 8.3 MPa, the values obtained for the developed geopolymers (between ~2 to 10 MPa) can be considered as totally adequate.

When a limb suffers a fracture, rupture, or dislocation, it is traditionally immobilized with plaster. This may induce discomfort in the patient, excessive itching and sweating, which creates the growth of bacteria, leading to an unhygienic and difficulty to keep clean from treatment. Furthermore, if the plaster remains for a long period, it may cause lesions in the joints and ligaments. To overcome all these disadvantages, orthoses have emerged as important medical devices to help patients in rehabilitation, as well as for self-care of deficiencies in clinics and daily life. Traditionally, these devices are produced manually, which becomes time-consuming and error prone. From another point-of-view, it is possible to use imageology (X-ray or computed tomography) to scan the human body; a process that may help orthoses manufacturing but induces radiation to the patient. To overcome this great disadvantage, several types of 3D scanners, without any kind of radiation have emerged. This article describes the use of various types of scanners capable of digitizing the human body, to produce custom orthoses. Studies have shown that photogrammetry is the most used and most suitable 3D scanner for the acquisition of the human body in 3D. With this evolution of technology, it is possible to decrease the scanning time and it will be possible to introduce this technology in clinical environment.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

The difficulty in detecting tumors in earlier stages is the major cause of mortalities of patients, despite the advancements in treatment and research regarding ovarian cancer. Deep Learning algorithms are applied to serve the purpose of a diagnostic tool by applying them on CT scan images of the ovarian region. The images go through a series of pre-processing techniques and further the tumor is segmented using the UNet model. Instances are then classified into two categories – benign and malignant tumors. Classification is performed using Deep Learning models like CNN, ResNet, DenseNet, Inception-ResNet, VGG16 and Xception along with Machine Learning models such as Random Forest, Gradient Boosting, AdaBoosting, XGBoosting. DenseNet 121 emerges as the best model on this dataset even after applying optimization on the Machine Learning models by obtaining an accuracy of 95.7%. The current work demonstrates the comparison of multiple CNN architectures among themselves and with common Machine Learning algorithms, with and without optimization techniques applied.

In this work, the decennial experience of Policumbent student team at Politecnico di Torino is summarized by focusing on the acquired knowledge in design of Human Powered Vehicles (HPVs) and on soft skills developed by both students and staff. Policumbent was funded by the authors at the end of 2008 in order to gather engineering students interested in design and construction of HPVs. In the last decade, the team has grown from 10 up to 50 students enrolled per year, exploring a range of HPV design for sports and mobility. Even when focusing on sport vehicles and extreme HPVs for speed record, such kind of projects allows students to familiarize with important concepts related to sustainable mobility: the amount of resistive forces and dissipated power, the role of vehicle weight and the impact of acceleration on the overall energetic balance as far as fundamental concepts about energy consumption, efficiency and emissions of the ``human engine'' in comparison with other kind of engines. By touching with hands such topics in the framework of a ``human-centred'' design project, the students have opportunity to develop awareness about the impact of design choices on sustainability of any kind of vehicle for transportation. Also, the paper retraces the team evolution path by focusing on a thorough analysis of what factors contributed to the success of this project.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Glutathione (GSH) and melatonin (MLT) are two antioxidants that have been described as having a protective role against oxidative stress in several animal species, improving sperm quality and survival after cryopreservation. Since there is no knowledge on the simultaneous use of these two substances concerning its effects on ram semen cryopreservation, this study aimed to evaluate the effects of MLT, GSH, or their association, on in vitro parameters of ram semen after thawing. During eight weekly sessions, the semen from three Merino rams was pooled, divided into four aliquots, and diluted with an egg yolk-based semen extender without (control) and with antioxidants (MLT 1mM, GSH 5mM, and MLT 1mM + GSH 5mM). Diluted semen was evaluated before and after freezing process. Supplementation of fresh semen with GSH at 5 mM had a deleterious effect on total motility progressive (TPM), curvilinear velocity (VCL), straight-line velocity (VSL), average-path velocity (VAP), linearity (LIN), straightness (STR) and increased slow spermatozoon (%). MLT at 1 mM also has a negative effect on TPM, VSL, and STR in fresh semen. In thawed semen, 1 mM of melatonin increased the TPM regarding the group control. Also, the combination of both antioxidants attenuates the negative effect of GSH 5mM on TPM, VSL and BCF. These results indicate that 5mM GSH impairs or does not improve sperm kinetic parameters in fresh semen and suggest that melatonin when combined with GSH plays a protective role on these effects.

60\% of the global population is expected to be in cities by 2050. At the same time the climate is changing at an accelerated rate. In this short paper we discuss the conflation of these two phenomena and how it may change the cities of the future. We formulate this as an optimization problem that could help answer important questions such as where are they likely to be located? How are they to be powered? What would be their demand for mobility and how might this be met? How over or under ground might these cities be? This paper first looks at a historical paradigm of cities in the absence of the climate crisis and then proposes the new paradigm to look at cities of the future faced by the challenge of the climate change crisis.

Background and Objectives: Rheumatic diseases often exhibit a complex pattern of comorbidities, including the increased occurrence of emotional disorders like anxiety and depression, which are closely related to the presence of chronic pain. Therefore, a multimodal approach is necessary for treatment, targeting both the physical and psychological functioning. Due to the increased burden within the healthcare context that emerged during the post-pandemic period, the need to adjust the content and length of psychological interventions became ubiquitous. In this way, the main objective of this study was to investigate the efficiency of a single-session, process-based psychological intervention for patients with rheumatic conditions and emotional comorbidities in a naturalistic, in-patient setting. Materials and Methods: After the screening, a total of 31 participants (Mage = 58.9, SD = 12.03) completed the single session intervention. The therapeutic protocol relied on a process-based cognitive-behavioural therapy framework aiming to improve cognitive, emotional and behavioural functioning. Assessments were conducted prior to the intervention, post-intervention and one month following the hospitalization. Results: Immediately after the intervention, significant reductions in dysfunctional cognitive and emotional processes, along with the improvement of behavioural strategies were observed. At the one-month telephonic evaluation, participants reported decreased pain, state anxiety and state depression levels. Conclusions: The single-session, process-based approach represents a promising intervention in healthcare contexts, targeting important psychopathological mechanisms in patients with rheumatic conditions. Future studies could clarify the extent to which these outcomes persist over time and their specific associations with anxiety and depressive symptoms, by using more controlled and rigorous trial designs.

Deep learning architectures like ResNet and Inception have produced accurate predictions for classifying benign and malignant tumors in the healthcare domain. This enables healthcare institutions to make data-driven decisions and potentially enable early detection of malignancy by employing computer-vision-based deep learning algorithms. These Convolutional Neural Network algorithms, in addition to requiring huge amounts of data, can identify higher and lower-level features that are significant while classifying tumors into benign or malignant. However, these algorithms have limitations concerning explainability and identifying the exact features that are of importance and contributing to the final classification of tumors as benign or malignant. In this paper, we implement several explainable AI techniques, namely, LIME, Saliency Map, Occlusion Analysis, Grad-CAM, SHAP, and Smooth Grad to interpret the results of a custom ResNet60 classifier in the classification of ovarian tumors as benign or malignant. The ResNet60 model attained an accuracy of 97.50% for the test dataset.

In this work, we incorporate a thixotropic-viscoelastic model into the widely used Computational Fluid Dynamics (CFD) software OpenFOAM, along with the rheoTool library. The model we implement is known as the Modified-Bautista-Manero (MBM), and effectively describes the rheological behavior of worm-like micellar solutions in extensional flows. We provide a detailed explanation of the numerical implementation of the model, specifically using the log-conformation tensor approach. Unlike previous works focused on this kind of fluids, we simulate inertial flows while considering convective terms in the governing equations, thus obtaining a more realistic behavior on the calculated results. The MBM model implementation is validated through numerical simulations on two different industrial-relevant geometries: the planar 4:1 contraction and the 4:1:4 contraction-expansion configurations. Furthermore, we investigate the influence of inertial, viscoelastic, and thixotropic effects on various flow field variables. These variables include velocity, viscosity, normal stresses, and corner vortex size. Our analysis encompasses both transient and steady solutions of corner vortexes across a range of Deborah and Reynolds numbers. Our results are also directly compared with simulations obtained using the non-thixotropic rubber network-based exponential Phan-Thien-Tanner (EPTT) model. From our planar 4:1 contraction results, we found that vortex-enhancement is seen when high elasticity is coupled with quick structural reformation and very low inertial effects. From our planar 4:1:4 contraction-expansion simulations, we show that an increase in inertia leads both to vortex-inhibition in the upstream channel and slight vortex-enhancement in the downstream channel. Lastly, we show the strong effect of the convection of fluidity into the fluidity profiles and into the upstream/downstream corner vortex sizes.

This critical review revisited the new classification system for periodontitis, specifically for staging, suggesting modifications, and introducing a new flowchart for a better clinical evaluation. It evaluated articles published between 2018 and 2024 in the English language, which had an educational motivation focused on staging periodontitis. PubMed/MEDLINE, Web of Science, and Embase databases were used to retrieve the articles. The focus questions involved the analysis of all parameters for staging periodontitis. A total of 836 articles were initially found; 388 duplicated were excluded; 448 were evaluated by title and abstract; 26 articles followed for full-text reading, and 6 articles were included in this critical review (k=0.98). All articles included detailed parameters and steps about how to diagnose periodontitis. Therefore, it was possible to observe instability and “gray zones” in the staging step, which was due to a lack of priority and an organized order sequence. This review suggests the severity parameters cannot be overcome by complexity parameters, following a cumulative sequence: CAL (1^st), RBL (2^nd), TLP (3^rd), and, after, complexity parameters. An exception must be permitted only for complexity factors between Stages III and IV that can change the initial Stage (III or IV) obtained through the severity analysis, but only between themselves. Moreover, for patients without tooth loss or with TLP of ≤4 teeth (without need for complex rehabilitation) and presenting any type of drifting or flaring or a secondary traumatic occlusion, it cannot be a justification for moving the diagnosis from Stage III to Stage IV.

Amid the covid-19 pandemic, other diseases, including viruses, are still acting to the detriment of their seasonality and risk factors for contagion. For this reason, it is interesting to know the degree of impact of other viruses, mainly respiratory, in which they have similar symptoms, in diagnoses for contamination by the new coronavirus based on epidemiological surveys, via epidemiological weeks, in Brazil. To what extent there may be a hypothesis of confusion of contaminated data, harming the health system, with regard to the need for intensive care units and control of viruses, and negatively or positively implying in the control or uncontrolling of viruses in general.

Objectives: The goal of this pilot study was to validate and introduce a new AI tool (algorithm), providing and comparing (1) the periodontal/peri-implant diagnosis between professional (specialist) and automated tool, (2) risk assessment and prognostication with the algorithm, and (3) establish cut-off limits for clinically significant disease with a new score system (GF-PeDRA score). Methods: All patients were evaluated by two evaluators, and in case of any divergence, the case was revisited and discussed until clarification and definition. The validation sample constituted 221 patients. The AI tool (GF-PeDRA©) had eighteen parameters to be assessed, involving systemic and local predictors, achieving an octadecagon (an eighteen-sided polygon). The parameters were: (1) The highest probing depth (PD); (2) Number of interproximal sites with bone loss; (3) The highest clinical attachment loss (CAL); (4) Maximum radiographic bone loss (RBL); (5) Bleeding on probing (% BoP); (6) Bone loss pattern; (7) Tooth loss including periodontally hopeless teeth planned for extraction; (8) Evidence of progression over five years; (9) Need for complex rehabilitation; (10) Patient’s age; (11) CAL and biofilm accumulation; (12) Smoking; (13) Diabetes; (14) Extension and distribution of the disease; (15) Peri-implant disease; (16) Other systemic conditions (other than diabetes); (17) Furcation involvement; and (18) Necrotizing lesion. A new score system (GF-PeDRA© score) based on the percentual of the octadecagon area is obtained; if the area was ≥0% to ≤9%, the prognosis is good; ≥10% and ≤ 24%, it is fair; ≥25% and ≤37%, poor; ≥38% and ≤49%, it is questionable; and between ≥50% to ≤100%, the prognosis is hopeless. Results: 221 patients were enrolled, with a mean age of 46.73. 5301 teeth were examined. 187 non-smokers (84.62%) and 34 smokers (15.38%) were included. 193 (87.33%) patients did not have diabetes, whereas 28 (12.67%) had. Comparing the diagnosis between both evaluators, k=0.83; all disagreed cases were re-discussed, and a final decision/diagnosis was reached. After this, the diagnosis found was contrasted with the diagnosis achieved by GF-PeDRA© and a perfect agreement was observed, 100% (k=1.0). 28 patients were diagnosed as periodontally healthy, 55 with plaque-induced gingivitis, and 138 with periodontitis. Only one case of molar/incisor pattern was observed. No peri-implant disease or necrotizing condition was found. The mean CAL found was 3.19 mm; 25 patients (11.31%) had a furcation involvement. The mean percentual of BoP found was 28.67% (median = 19%; maximum: 100%; minimum: 100%); and the mean PD was 5.31 mm. The mean of the new GF-PeDRA© score (ranging from 0% to 100%) was 28.64%, with a median of 32.2% (minimum: 0.6% and maximum: 64.1%). Then, analyzing the GF-PeDRA© score of 221 patients enrolled, 48 (21.73%) were sorted as a Good prognosis for periodontal treatment, 43 (19.45%) had a Fair prognosis, 43 (19.45%) had a Poor prognosis, 68 (30.77%) had a Questionable prognosis, and 19 (8.60%) had a Hopeless prognosis. Conclusion: The new AI tool (GF-PeDRA©) was validated and proved to be extremely helpful in diagnosing and providing risk assessment and prognosis.

Evaluation of drug permeability using cell monolayers is an important in vitro assay in the process of drug development, to identify compounds with favourable pharmacokinetics that may proceed to in vivo studies. When allowed to differentiate on permeable filters for at least 21 days, monolayers of Caco-2 cells develop morphological and functional properties similar to those of the intestinal epithelium. Permeability through Caco-2 monolayers is thus particularly relevant to assess drug absorption after oral administration. The major drawback of this assay is its very low throughput, with the cell monolayers being used in a single permeability assay. We have previously proposed a protocol to allow the re-use of the Caco-2 monolayer on additional permeability assays during the stable period and shown that cell monolayer integrity is maintained. In this work we evaluate the effect of re-use on the permeability of several reference compounds that permeate through passive pathways and show that the cell monolayers can be re-used twice in additional permeability assays. Preliminary results were also obtained regarding active transport pathways, and a new methodology is proposed to quantify the contribution from passive and active transport. This is a major step towards the full validation of the re-use methodology proposed, which at least triplicates the throughput of this important in vitro assay.

During normal ageing, physical changes take place, namely in terms of the biomechanical, musculoskeletal, and psychomotor systems, that reduce strength, flexibility, motor coordination, balance, and precision of movements. This article analyses the motion behaviour of a sample of 49 senior and pre-senior subjects during the process of entry to (ingress) and exit from (egress) new car models not experienced before, obtained over five days at the Geneva International Motor Show. The methodological process is based on visual studies using photography and video to analyse motion behaviour. This investigation identifies five entry movement strategies and three exit movement strategies in three types of vehicle groups. The movements adopted in the egress of the vehicle were more complex and difficult, in general, than those observed for ingress, requiring greater flexibility, agility/dexterity, and physical strength of subjects, involving more contact or support with vehicle parts. The main factor that influences movement strategies is essentially related to subjects’ levels of physical capacity and previous experiences. In conclusion, there are no significant changes in the subjects’ somatic movement strategies based on vehicle types.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

The literature, aimed at understanding the income-price elasticity of air passenger demand, bases its analysis on airport movement. The diversity of studies regarding the casualty between air transportation and economic growth are examples. Some studies covering this link, estimate the income-price relationship with the demand considering international traffic. Considering a domestic setting, where this traffic is significant in Brazil, studies related to remote regions are scarce, and the existing ones focus on governmental policies and subsidies. In addition, empirical studies on the theme consenter themselves in developed regions, such as Europe, North America, and Australia. For Brazil, where we find the Amazon region, there are no empirical researches. This paper analyses the price-income elasticity of the demand regarding domestic passengers in air links from remote cities of the Brazilian Amazon. This study uses panel data regression analysis method on a database of domestic scheduled flights of Brazil´s National Civil Aviation Agency. The results show that air passengers involving remote region flights present a lower sensitiveness regarding local income and airline´s price variations than those in flights among capitals. The higher difference is in income-elasticity of the remote city of origin, which is lower than that of the air traffic among capitals.

Background: Research articles are essential for describing new ideas, techniques, and procedures and consolidating concepts. It creates an opportunity to expose studies and publicly assimilate published knowledge. Therefore, one of them is the most used and accepted index to verify the author’s scientific impact is the H-index or Hirsch index. It provides a robust single metric that combines quality and quantity. Therefore, it presents disadvantages, (1) researchers with shorter scientific carriers may have fewer articles and citations than those with longer scientific life; (2) it allows scientists to receive citations even if no new papers are published; (3) it is only useful for comparing the better scientists in a field; (4) this indicator can never decrease; (5) it is only weakly sensitive to the number of citations received; (6) the major and minor (or no) contributor in the research gained equal h-index. Then, the H-index ignores the total of citations and the time of a researcher's experience (“scientific age” [sa]). Objective: Thus, the goal of this study was to present a new index system (GFsa index ©) based on the two variables completely forgotten (total of citations and “scientific age”), introducing a new terminology “scientific age”, to evaluate the best-ranked researchers in Dentistry. Methods: The AD Scientific Index was used, and all researchers included in this study were cited in the AD Scientific Index (2024) in the Dentistry field and had the Google Scholar page accessible for a consultation to manually obtain the total of citations and calculate the “scientific age”. The information was retrieved by two authors (G.V.O.F. and J.C.H.F.), who assessed the data twice to avoid errors or mistakes. For inclusion: a minimum H-index value of 30; for exclusion: (i) the author did not have a Google Scholar page; (ii) duplicated author; or (iii) presented any suspicious activities about manipulation of articles. Then, a dataset of all researchers who were reported in Dentistry was prepared (name, H-index, i10 index, and publications). The formula developed and applied was GFsa=(total number of citations)/(“scientific age)². The Pearson correlation statistically evaluated the data obtained; the confidence interval was 95%. Results: A total of 9,093 researchers in Dentistry were recorded, of whom 1,020 were included. Then, we collected all 1,020 researchers' Google Scholar data (publications, citations, and indexes), and each researcher's total citations and “scientific age” were registered and calculated. The mean “scientific age” registered was 34.18 ± 13.34 (standard error of mean = 0.4181). With this information and data collected, GFsa index © was calculated, presenting a minimum value of 0.2186 and a maximum of 154.8 (mean = 10.33 ± 11.82; standard error of mean = 0.3706). Then, the data was organized and sorted following the ranking obtained in the GFsa index ©. The Pearson correlation showed that the H-index had a weakly positive association with the researcher’s “scientific age”; this fact means that the H-index will increase according to the “scientific age” increase. Otherwise, a moderately negative correlation between GFsa and “scientific age” was demonstrated, whereby a higher GFsa © had a lower “Scientific age”. This assessment shows that the variables introduced were fairly used. Moreover, a positive correlation was observed between both indexes (H-index and GFsa). Conclusion: It is possible to conclude that the new variable reported (“Scientific age”) and using the total citations brought a fairer and more feasible evaluation among the researchers. Thus, we are launching the new GFsa index © and the new information named “Scientific age” for the first time in the literature. The future perspective of the GFsa © application will be (1) the evaluation of the 9,093 researchers in Dentistry (total initially registered), including more authors/researchers in the Dentistry field, (2) expanding the exposition of this new index for other areas of the knowledge, and (3) provide free access of all data through the website (http://gfindex.us.to).

The object of this work is to report some preliminary results on the mechanical harvesting of blueberry fruits of cv. Cargo® in the Piedmont region, one of the most productive areas of Italy that is specialized for fresh blueberry production. The automatization of harvesting operations could represent a competitive advantage for the investigated area’s blueberries supply chain, but could act as a limitation to maintaining the quality of fresh berries. A prototype machine and a commercial harvester (Easy Harvester®) were compared to manual picking, considering harvest efficiency (share of loss), labor productivity and harvesting cost. In the indicated context, the cost of labor exceeds 2.00 euros per kg of sellable product. The use of the prototype allowed a 37% re-duction of this cost, and the use of the Easy Harvester® allowed a reduction of about two thirds. It should be emphasized that these positive performances do not consider two other aspects: the re-duction in the marketable volume (attributable to losses in the harvest and post-harvest phase), and the reduction in the net sale price by 0.30 euros due to the sorting/selection costs in the ware-house. In this study, we highlight how the transition to mechanical harvesting requires the trans-formation of several farming and warehouse operations, such as new crop varieties, new field configurations, and new packaging processes. However, a possible technical improvement of the Easy Harvester® machine could represent an opportunity for Italian companies in the planning of the production and marketing of berries, involving all actors of the supply chain. Further research on the use of mechanization in the sector must still be continued and supported.

In the last years, new numerical methods have been applied to weather data for water budget es-timation. Geostatistics is one of the most powerful approaches, when it comes to studying spatially relevant natural phenomena, as it takes into account the spatial correlation among measurements over a specific study area and increases the reliability of the estimation by providing the associate uncertainty. In this study, we tested the feasibility of using a geostatistical method called Ordinary Kriging to provide a reliable estimation of the water budget of the Foro river basin (Periadriatic area, Central Italy), by comparing the obtained results with a more traditional yet robust approach based on the Thiessen polygon spatialization method, considered here as a reference. The spatial estimation with the selected geostatistical and traditional approaches was performed on the av-erage monthly rainfall and temperatures derived from 33-year-long time series measured at the weather station of the regional monitoring network. To transform the spatial variables quantities of both rainfall and air temperature into actual runoff estimates that ideally represent the river dis-charge, we used both the Turc and Thornthwaite methods, considering variable Potential Infiltra-tion Coefficients according to the hydrogeological complexes’ distribution. For the geostatistical method, the same procedure was applied to the 95% confidence interval limits, to quantitatively assess the possible impact of the spatial uncertainty on the estimation of the river discharge. The results obtained by both methods, subsequently converted into monthly discharges, were com-pared to the average monthly discharges related to 33-year-long time series measured at different locations along the Foro river. The results obtained with the geostatistical approach proved to be in line with the ones from the traditional method. Additionally, using the rainfall and temperature values obtained with the Ordinary Kriging and the corresponding confidence interval limits, it was possible to quantify the uncertainty associated with the discharge values, making the estimates more reliable than the ones obtained with the traditional approach. However, the yearly distribu-tion of river discharge obtained by both the geostatistical and traditional methods appeared to be dissimilar to the measured ones. In such anthropized and groundwater-dependent river basins, the surface water use as well as the regulatory effect of the alluvial aquifer regime may affect the river discharge variability over the year and then can account for similar discrepancies between the in-flow and outflow water volumes.

The present study deals with the transplantation of mature Argan trees (Argania spinosa L. Skeels) and focuses on optimizing survival rates depending on the seasons, the type of shoot pruning applied to the trees and preconditioning treatments consisting of root pruningand watering for a few months before transplanting. So far, the transplantation of this species at the adult stage has not received enough attention in spite of its ecological and socio-economic importance for the regions where it thrives. The results obtained show that transplanting in summer, autumn and winter resulted in survival rates exceeding 50%. The Argan trees transplanted in spring hardly achieved 10% survival. However, the total cutback of the crown induced survival improvement that reached a rate greater than 70% for summer, autumn and winter, and 50% for spring. Watering alone or combined with root pruning for 6 months helped improve the recovery rate but only when carried out in autumn with transplantation in spring. On the other hand, when these pre-treatments were applied in the spring to transplant the trees in summer, the recovery rate was not improved.

Advanced Nano structural hard coatings are thin materials films that range in thickness from a few nanometers to a few micrometers and are applied to different surfaces to increase their hardness and wear resistance. Physical vapor deposition (PVD) or chemical vapor deposition (CVD) methods are frequently used to deposit these coatings. These coating’s distinctive characteristics result from their microstructure, which is made up of material columns or grains with a diameter of only a few nanometers. Increased hardness, higher wear resistance, and improved tribological properties result from these short dimensions. In applications with significant wear and/or high contact pressures, such as cutting tools, bearings, and engine parts, the usage of sophisticated Nano structural hard coatings is crucial. Advanced Nano structural hard coatings include, 1. Amorphous carbon coatings with high hardness, low friction, and exceptional wear resistance are known as diamond-like carbon (DLC) coatings. DLC coatings are frequently used in a variety of industries, including the automotive, aerospace, and biomedical ones. 2. Coatings made of titanium nitride (TiN): These metallic coatings have high hardness and wear resistance. Cutting tool, machining, and aerospace industries frequently use TiN coatings. 3. Chromium nitride (CrN) coatings: These coatings have great corrosion resistance, good wear resistance, and high hardness. Cutting tools, gears, and bearings are just a few of the objects that use CrN coatings. 4. Tungsten carbide (WC) coatings: These coatings, which have a high degree of hardness and wear resistance, are frequently employed in cutting tools and other applications that require wear resistance. Advanced Nano structural hard coatings provide many advantages over conventional coatings, including better hardness, increased wear resistance, and improved tribological qualities. The automotive, aerospace, and biomedical industries are just a few that could use these coatings. In this paper the author will explain about the design synthesis and applications of advanced Nano structural hard coating in aerospace and automotive applications.

Purpose: The goal of this article was to introduce a new technique for root coverage (RC), the Mixed-Thickness Tunnel access (MiTT), approaching a full-split design, showing the results obtained in a case series and demonstrating it step-by-step. Methods: Healthy individuals, non-smokers, and non-diabetics, who were diagnosed with gingival recession (GR) type 1 or 2 (RT1 or RT2). After all necessary evaluations, prophylaxis was performed 14 days before the surgical procedure. Then, after the basics clinical conduct and anesthesia, one or two vertical incision(s) on the mucosa (around 1-2 mm apical to the MGJ), lateral to the papilla base, were done. Initial detachment of the mucosa from the muscles (split design); it was permitted (but not mandatory) to do intrasulcular incisions; from the MGJ to coronal, subperiosteal access was done to raise the full-thickness tunnel. It must communicate up to the gingival sulcus area and the papilla’s base, keeping the papilla’s tip intact. A connective tissue graft was harvested, which was inserted through the linear incision or intrasulcularly. Interrupted sutures were done and may be used as adjunctive material. Results: Nine healthy individuals (7 females and 2 males) aged 19 and 43 years were enrolled. They were treated following the MiTT steps. There were four cases with a single GR, 2 patients with 2 teeth involved, and three with 3 or 4 GR. Seven cases were RT1 and two RT2. All RT1 cases achieved 100% RC, while the mean RC obtained for RT2 was around 80%. Conclusion: MiTT can be considered a more straightforward approach for minimally invasive surgical technique, which is a feasible option to treat RC with a high success rate, predictability, and esthetic preservation. There is a technical sensitivity to performing the full-split design procedure.

Chronic noncommunicable diseases (CNCDs) have been a major public health concern worldwide, especially diabetes, cardiovascular disease, chronic obstructive pulmonary disease, hypertension, in addition to obesity, which is even more worrying when the subject involves the covid-19 pandemic, because such incidences correlate with the need for intensive care units, including the possibility of death of the patient. Therefore, for countries with the highest numbers of critical cases, it is important to assess the incidence of these diseases to guide the public that most needs guidance on public policies for social isolation.

Biomechanics is a branch of biophysics that deals with mechanics applied to biology. The biomechanics of the cornea plays a significant role in managing patients with glaucoma. While evidence suggests a higher risk of glaucoma in patients with thin and stiffer corneas, it also affects the measurement of intraocular pressure (IOP). We reviewed the pertinent literature to help the understanding of corneal biomechanics and how it can help optimize clinical and surgical treatments and a better approach to diagnosing and managing patients with glaucoma.

This study focuses on the potential medicinal properties of Campsis radicans L. extracts and its aim is to investigate the antioxidant and antiproliferative effects of these extracts on the human colon adenocarcinoma cell line (HT-29). Cytotoxic activity in the HT-29 cell line was evaluated, and the 3-dimensional structures of phenolic compounds were obtained using the GC-MS method. Docking simulations were performed with AutoDock Vina, targeting proteins that are crucial in the apoptotic pathway (Bax, Bcl-2, and Caspase-3). Drug similarities and ADMET estimates of the phenolic compounds were obtained from databases. The highest antioxidant activity of Campsis radicans L. plant was observed in ethanol and water extracts, with notable inhibition capacities. While the total phenolic content was highest in ethanol, water, and ether extracts respectively the total flavonoid content was highest in ethanol, then ether, and water extracts. Certain elements were undetectable in mineral determination, and others exceeded the toxic doses for plants. The water extract exhibited dose-dependent cytotoxic activity in the HT-29 cell line, with an IC50 value of 4.47 mg/mL. Molecular docking results revealed the binding of phenolic molecules to the active sites of apoptotic pathway proteins. The findings suggest that Campsis radicans L. plant possesses cytotoxic properties, significant phenolic and flavonoid content, and a high antioxidant capacity. These properties make it a potential candidate for treatment use, emphasizing its potential therapeutic value in the HT-29 cell line. Further research and exploration on the identified phenolic compounds could contribute to the development of novel therapeutic agents.

The study of phytotherapy in dentistry is relevant due to the low occurrence of research in the treatment of oral pathologies, such as caries and periodontal disease. Thus, the aim of this research was to characterize the chemical composition of extracts from the leaves of Couroupita guianensis Aubl, including toxicological evaluation and the antioxidant and antimicrobial potential against Staphylococcus aureus, Streptococcus mutans and Candida albicans. Three extracts were prepared using assisted ultrasound, originating the Crude Ultrasound Extract (CUE) and Soxhlet apparatus, originating the Crude Soxhlet Extract (CSE) and the Ethanol Soxhlet Extract (ESE). In the analysis of the chemical composition, the presence of flavonoids, tannins and saponins were detected. LC-DAD analysis revealed the presence of caffeic acid, sinapic acid, rutin, quercetin, luteolin, kaempferol and apigenin in all extracts. In the GC-MS analysis, stigmasterol and β-sitosterol were identified in CUE and CSE. The antioxidant potentials, determined by the DPPH• and ABTS•+ methods, the ESE showed higher antioxidant activity (2.98 ± 0.96 and 4.93 ± 0.90, respectively). In the evaluation of toxicity, the CUE 50µg/mL and the ESE 50 µg/mL presented growth stimulation of Allium cepa roots. At a concentration of 750µg/mL, all extracts inhibited root growth. None of the extracts showed toxicity against Artemia salina. Antibacterial action was detected in all extracts, mainly against the microorganisms S. aureus and S. mutans; however, the antifungal action against C. albicans was not detected. From the results, the extracts of C. guianensis have therapeutic potential for use in the control of microorganisms in the oral microbiota.

Chondrosarcoma, represents approximately 0.1% of all neoplasms of the head and neck, being considered a rare disease, but with a relatively good prognosis. The 5-year overall survival (OS) rate is estimated at 70-80%, being considered a disease with a low growth rate. About 13% of all cases of chondrosarcoma, are located in the region of the head and neck. We present the case of a young patient treated multimodally, lost from the oncological records less than two years after the diagnosis, without evidence of disease progression. The early loss from the oncological follow-up programs of patients with a lower risk of early repalpse, without evidence of a recurrence or metastasis could be the consequence of a major complication among which we could assume an aspiration pneumonia secondary to a dysphagia, associated with an aggressive multidisciplinary treatment. Large tumor size and positive resection margins (R1 resection) are risk factors that support an intensive adjuvant approach in order to reduce the risk of recurrence, but the low grade of tumor, associating a lower risk of recurrence as well as the adverse events (AE) of adjuvant radiotherapy and chemotherapy justifies a more reserved therapeutic approach. Taking into account the longer life expectancy of these patients, it is recommended to use a more conformal irradiation technique in order to reduce doses to radiosensitive structures as well as to omit elective neck irradiation, taking into account the lower risk of lymph node involvement. The lack of guidelines that include very rare tumors including low grade chondrosarcoma of head and neck make a unified approach difficult, but the data presented even in case reports could contribute to choosing the regimen that offers the best therapeutic ratio.

Callus induction (CI) is the critical trait for the transformation of desirable genes in plants. A genome-wide association study (GWAS) analysis was conducted on the rice germplasm of 110 diverse indica rice accessions. Three tissue culture media, including B5, MS, and N6, were used for CI in those rice panels. Seven quantitative trait loci (QTLs) on chromosomes 2, 6, 7, and 11 were found to confer a CI percentage in these three media. For the B5 medium, one QTL (qCI-B5-Chr6) was identified on the rice chromosome 6. For the MS medium, two QTLs were identified on the rice chromosomes 2 and 6 (qCI-MS-Chr2 and qCI-MS-Chr6, respectively). For the N6 medium, four QTLs were identified on the rice chromosomes 6, 7, and 11 (qCI-N6-Chr6.1, qCI-N6-Chr6.2, qCI-N6-Chr7, and qCI-N6-Chr11, respectively). Fifty-five genes were identified within the haplotype blocks corresponding to these QTLs. Thirty-one genes showed haplotypes associated with different CI in those media. The qCI-B5-Chr6 was located in the same region as the qCI-N6-Chr6.2. The caleosin-related family protein was identified in this region. Analysis of the gene-based haplotype reveals the association of this gene with different CI in both B5 and N6 media, suggesting that the gene may play a critical role in the CI mechanism. Moreover, several genes, including the beta-tubulin, the zinc finger proteins, the RNP-1 domain-containing protein, and the Lysophosphatidic acid acyltransferase, were associated with different CI in the N6 media. Results from this study provide insight into the potential QTLs and candidate genes for callus induction in rice that will fulfill the understanding of the physiological and biochemical processes involved in callus formation, which is an essential tool in the molecular breeding of rice.

Recent findings have demonstrated an increase in the prevalence of childhood obesity and overweight in Portugal, urging the need to study modifiable risk factors such as parental feeding practices. The Comprehensive Feeding Practices Questionnaire (CFPQ) is an important self-report measure assessing a broad range of responsive and non-responsive feeding practices. However, the CFPQ has not yet been validated in Portugal. Therefore, the present study aimed to test the validity of this measure with Portuguese parents of 2- to 8-year-old children. A sample of 409 parents completed a Portuguese-adapted version of the CFPQ and the already validated Child Feeding Questionnaire (CFQ). Confirmatory Factor Analysis (CFA), Exploratory Factor Analysis (EFA), and psychometric analysis were conducted. CFA demonstrated the original 12-factor structure did not fit the sample. EFA identified an 8-factor structure, comprising 29 items: Monitoring, Modeling, Environment, Involvement, Emotion Regulation, Restriction for Weight Control, Restriction for Health, and Pressure. Findings suggest that parental feeding practices are sensitive to parents’ background culture and children’s developmental period.

Pigmented corn is a gramineae food of great biological, cultural and nutritional importance for many Latin American countries, with more than 250 breeds in the American continent. It confers a large number of health benefits due to its diverse and abundant bioactive compounds. In this narrative review we decided to organize the information on the nutrients, bioactive compounds and phytochemicals present in pigmented corn, as well as their effects on human health. Phenolic compounds and anthocyanins are some of the most studied and representative compounds in these grasses, with a wide range of health properties, mainly the reduction of prooxidant molecules. Carotenoids are a group of molecules belonging to the terpenic compounds, present in a large number of pigmented corn breeds, mainly the yellow ones, whose biological activity incorporates a wide spectrum. Bioactive peptides can be found in abundance in corn, having very diverse biological effects that include analgesic, opioid, antihypertensive, etc. activity. Other compounds with biological activity found in pigmented corn are resistant starches, some fatty acids, phytosterols, policosanols, phospholipids, ferulic acid and phlobaphenes, as well as a great variety of vitamins, elements, and fibers. This review aims to disseminate and integrate the existing knowledge on compounds with biological activity in pigmented corn, in order to promote their research, interest and use by scientists, nutrition professionals, physicians, industries and the general population.

This review examines the effects of lingonberry (Vaccinium vitis-idaea L.) on general and oral health. The effects of lingonberry are based on the vitamins, minerals, fibers and polyphenolic compounds it contains. Lingonberry's bioactive substances have a diverse range of antimicrobial, anti-inflammatory, antiproteolytic, anticarcinogenic and antioxidant properties. Research results suggest that lingonberries can have a positive effect on human health. Berries, lingonberry juice/lingonberry nectar/fermented lingonberry juice and polyphenol fractions have been used in clinical studies. Lingonberries balance post-meal blood sugar, free fatty acids and insulin levels. Fermented lingonberry juice reduces Streptococcus mutans, Candida and periodontal pathogen counts, but is probiotic because it favors growth of Lactobacilli. In addition, it increases saliva secretion and thus lowers the risk of oral infections. It lowers the clinical parameters of periodontitis and the active matrix metalloprotease-8, reducing the low-grade inflammation associated with periodontal diseases. More studies on humans are needed.

Diabetes is a prevalent global health issue associated with significant morbidity and mortality. Diabetic retinopathy (DR) is a well-known inflammatory, neurovascular complication of diabetes and a leading cause of preventable blindness in developed countries among working-age adults. However, the ocular surface components of diabetic eyes are also at risk of damage due to uncontrolled diabetes, which is often overlooked. Inflammatory changes in the corneas of diabetic patients indicate that inflammation plays a significant role in diabetic complications, much like in DR. The eye´s immune privilege restricts immune and inflammatory responses, and the cornea and retina have a complex network of innate immune cells that maintain immune homeostasis. Nevertheless, low-grade inflammation in diabetes contributes to immune dysregulation. This article aims to provide an overview and discussion of how diabetes affects the ocular immune system’s main components, immune-competent cells, and inflammatory mediators. By understanding these effects, potential interventions and treatments may be developed to improve the ocular health of diabetic patients.

Lactobacilli are considered an inexhaustible source of potentially bioactive substances; indeed, several products from their metabolism are known to have immunomodulatory and anti-inflammatory activity. Recently, we demonstrated that cell-free supernatants (CFS) obtained from Lactobacillus (L.) acidophilus, L. plantarum, L. rhamnosus and L. reuteri can impair Candida pathogenic potential in an in vitro model of epithelial vaginal infection. This effect could be ascribed to a direct effect of living lactobacilli on Candida virulence and to the production of metabolites which are able to impair fungal virulence. In the present work, stemming from those data, we deepened our knowledge on the CFS from these 4 lactobacilli by performing a metabolomic analysis to better characterize their composition. By using an untargeted metabolomic approach, we detected consistent differences in the metabolites produced by these four different lactobacilli. Interestingly, L. rhamnosus showed the most peculiar metabolic profile. Specifically, after a hierarchical clustering analysis in positive and negative ionization mode, L. rhamnosus showed a specific area of significant overexpressed metabolites that strongly differed from the same area in other lactobacilli. In this area, inosine was identified among the overexpressed metabolites of L. rhamnosus. This molecule has been described to have antioxidant, anti-inflammatory, anti-infective and neuroprotective properties. The biological significance of its overproduction by L. rhamnosus might be important in its probiotic and/or postbiotic activity.

Adipose tissue (AT) is a remarkably plastic and active organ with functional pleiot-ropism and high remodeling capacity. Although the expansion of fat mass, by defini-tion, represents the hallmark of obesity, the dysregulation of the adipose organ emerges as the forefront of the link between adiposity and its associated metabolic and cardio-vascular complications. The dysfunctional fat displays distinct biological signatures, which include enlarged fat cells (i.e., adipocyte hypertrophy), low-grade inflammation, impaired redox homeostasis, and cellular senescence. While these events are orches-trated in a cell-type, context-dependent and temporal manner, the failure of the adipose precursor cells to form new mature adipocytes appears the main instigator of the adi-pose dysregulation, which, ultimately, poses a deleterious milieu either by promoting ectopic lipid overspill in non-adipose targets (i.e., lipotoxicity) or by inducing an al-tered secretion of different adipose-derived hormones (i.e., adipokines and lipokines). This novel paradigm (“expandability hypothesis”) challenges and extends previous “adipocentric view”, which implies a reduced plasticity of the adipose organ at the nexus between “unhealthy” fat expansion and the development of obesity-associated comorbidities. In this review, we will briefly summarize the potential mechanisms by which adaptive changes to variations of energy balance may impair adipose plasticity and promote fat organ dysfunction. We will also highlight the conundrum with the perturbation of the adipose microenvironment and the development of cardio-metabolic complications by focusing on adipose lipoxidation and cellular senescence. Finally, we discuss the sci-entific rationale for proposing adipose organ plasticity as a target to curb/prevent adi-posity-linked cardio-metabolic complications.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

Environmental degradation leads to a totally unsustainable food system. In addition to this is-sue, the consumption of foods that improve people's health and well-being is recommend-ed. These guidelines create new challenges and the demand for alternatives to meet these needs in the short term. One of the alternatives is undoubtedly the use of by-products of winemaking, namely in the form of grape pomace flour (GPF), which is obtained in a totally sustainable way, requires no further water consumption or agricultural land, and is an ingredient that boasts all the characteristics that meet the circular economy and has colossal potential in promoting nutrition and healthy eating. To verify the benefits of using the Touriga Nacional and Arinto (Vitis vinifera L.) flour varieties, analytical determinations were made to identify and quantify different components, such as nitrogen and extractable phosphorus, ash, moisture, proteins, fats, dietary fibers, total sugars, and phenolic content. GPF could become a valuable ingredient due to its nutritional quality and high content in various polyphenols namely flavonoids and pyranoanthocyanins.

Spontaneous tumours in higher plants can develop depending on plant genotype without any pathogen invasion. Spontaneous tumour formation on the taproots is consistently observed in certain inbred lines of radish (Raphanus sativus var. radicula Pers.). In this work, we have sequenced the genomes of two closely related radish inbred lines that differ in their ability to spontaneously form tumours. We have identified numerous single nucleotide variants (amino acid substitutions, insertions or deletions) that are likely to be associated with the spontaneous tumour formation. Furthermore, we performed the identification of CLE and WOX genes the genomic sequences of the radish inbred lines and, as a result, identified two unique radish CLE genes which probably encode proteins with multiple CLE domains. The results obtained provide a basis for investigating the mechanisms of plant tumour formation and also for future genetic and genomic studies of radish.

The recent availability of commercial platforms for behavioral analysis in zebrafish larvae based on video-tracking technologies has exponentially increased the number of studies analyzing different behaviors in this model organism to assess neurotoxicity. Among the most commonly used assays in zebrafish larvae are basal locomotor activity (BLA) and visual motor response (VMR). However, the effect of different intrinsic and extrinsic factors that can significantly alter the outcome of these assays is still not well understood. In this work we have analyzed in 143 larvae the influence of age (5-8 days post-fertilization), time of day (8:00, 10:00, 12:00, 14:00; 16:00, 18:00, and 20:00 h), and experiment (three experiments performed at different days) on BLA and VMR results (4,004 analyses for each behavior). Results from both behaviors were adjusted to a Random-Effects linear regression model using generalized least squares (GLS), including in the model the effect of the three variables, the second-way interactions between them and the three-way interaction. The results presented in this manuscript show a specific effect of all three intrinsic factors and their interactions on both behaviors, supporting the view that the most stable time period for performing these behavioral assays is from 10:00 am to 04:00 pm, with some differences depending on age of the larva and the behavioral test.

Many protein expression systems are primary utilised to produce a single, specific recombinant protein. In contrast, most biological processes such as virus assembly rely upon a complex of several interacting proteins rather than the activity of a sole protein. The high complexity of the baculovirus genome, coupled with a multiphase replication cycle incorporating distinct transcriptional steps, made it the ideal system to manipulate for high-level expression of a single or co-expression of multiple foreign proteins within a single cell. We have developed and utilised a series of recombinant baculovirus systems to unravel the sequential assembly process of a complex non-enveloped model virus, Bluetongue virus (BTV). The high protein yields expressed by the baculovirus system not only facilitated structure-function analysis of each viral proteins but were also advantageous to crystallography studies and supported the first atomic level resolution of a recombinant viral protein, the major BTV capsid protein. Further, the formation of recombinant double-shelled virus-like particles (VLPs) provided insights into the structure-function relationships among the four major structural proteins of the BTV whilst also representing a potential candidate for a viral vaccine. The baculovirus multi-gene expression system facilitated the study of structurally complex viruses (both non-enveloped and enveloped viruses) and heralded in a new generation of viral vaccines.

Magnetorheological fluids (MRFs) are smart materials consisting of micro-scale magnetizable particles suspended in a carrier fluid. The rheological properties of a MRF can be changed from a fluid-state to a solid-state upon the application of an external magnetic field. This study reports the development of a particle-level simulation code for magnetic solid spheres moving through an incompressible Newtonian carrier fluid. The numerical algorithm is implemented within an open-source finite-volume solver coupled with an immersed boundary method (FVM-IBM) to perform fully-resolved simulations. The particulate phase of the MRF is modeled using the discrete element method (DEM). The resultant force acting on the particles due to the external magnetic field (i.e., magnetostatic polarization force) is computed based on the Clausius-Mossotti relationship. The fixed and mutual dipole magnetic models are then used to account for the magnetic (MAG) interactions between particles. Several benchmark flows were simulated using the newly-developed FVM-IBM-DEM-MAG algorithm to assess the accuracy and robustness of the calculations. First, the sedimentation of two spheres in a rectangular duct containing a Newtonian fluid is computed without the presence of an external magnetic field, mimicking the so-called drafting-kissing-tumbling (DKT) phenomenon. The numerical results obtained for the DKT case study are verified against published data from the scientific literature. Second, we activate both the magnetostatic polarization and the dipole-dipole forces and resultant torques between the spheres for the DKT case study. Next, we study the robustness of the FVM-IBM-DEM-MAG solver by computing multi-particle chaining (i.e., particle assembly) in a two-dimensional (2D) domain for area volume fractions of 20% (260 particles) and 30% (390 particles) under vertical and horizontal magnetic fields. Finally, the fourth computational experiment describes the multi-particle chaining in a three-dimensional (3D) domain allowing to study fully-resolved MRF simulations of 580 magnetic particles under vertical and horizontal magnetic fields.

Village has a vital role in the national development efforts. The concept of development considered village as an object instead of a subject of development. This study focused on determining the important points in enabling a village to be independent by shifting the paradigm of “building the village” into “the building village”. This study was an exploratory research of public policies with qualitative legal studies. This study was conducted in 3 villages in Bandung regency with different characteristics, namely Neglawangi with urban characteristics, Cibiru Wetan with sub-urban characteristics, and Rancamanyar with plural characteristics. The results of this study showed that the wise step in building an independent village is through “the building village” road maps. First, encourage the inception of critical and care community and community organizations who dynamically interact in the policy making processes of village development. Second, implement a participative, accountable, and transparent planning and budgeting system within the limits of their authorities. Third, empower inclusive village economic institutions. The three road maps can succeed if they are supported by good implementation of participative, systematic, effective and efficient planning and budgeting system, as well as good monitoring.

The olfactory system is capable of distinguishing individual odorants from among a virtually unlimited number. Fish, for example, detect changes in the electric field environment induced by prey and other sources. Floral electric fields exhibit variations in pattern and structure, which can be discriminated by bumblebees. We have constructed an electric field sensor, which, in the course of focussing on achieving maximum sensitivity and consistency, ultimately resembles features of the insect sensorium. A “fingerprint” 3D plot ( time, frequency range, voltage amplitude), representing the emitted electric field profile, is presented for each of a variety of odorants and other chemicals. The substance-specific electric-field emission and identification is not impeded by containers or barriers or distance.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

In many European countries over the last decades, arable fields dominate agriculture landscapes, leading to a very intensive land-use practices. This reason seems to be the main cause of popula-tions declines for numerous farmland species, including the European hare (Lepus europaeus Pallas, 1778). The Research institute for Animal Production (National Agricultural and Food Centre, Luzianky, Slovakia) has been engaged in a long monitoring project (project currently run-ning), collecting certain indicators of hare population dynamics during hunting season since 1987 to 2023 in the Slovak Danubian Lowland. In the same macro-area (Čiližská Radvaň and Lehnice) a study was conducted on the influence of permanent semi-natural vegetation in relation to re-cruitment, population density and production. The whole monitored period was aggregated into 5-years intervals (for a total of 7 time-intervals), with the aim of analyzing the brown hare popu-lation dynamics. Spring hare density in the Danubian Lowland is currently 20.8 hares/km2, with harvests of 4.6 hares/km2. During all the monitoring period, bag’s animals have been examined following the regular hunting operations for the purpose of age determination (weight of eye lenses), sex ratio and productivity. The results of our analysis showed that the proportion of juve-nile in bag (PYB) among those shot varied from 37.0 % of the last 5-years interval (2018-2023), to a maximum of 51.0 % in interval of years 1998-2002. On total average there were 1.86 juveniles per adult female (r). The proportion of adult females in gamebag varied from 22.58 % (years in-terval 1992-1997) to 31.26 % (years interval 2018-2023). Sex-ratio (SI; males : females) among shot hares showed a value of 0.50, ranged from 0.48 in the period 2008-2012 to 0.52 in the first observed period (years 1987-1991) and in the last one (years 2018-2023). Average weight of shot hares was 4.04 kg (juveniles 3.83 kg, adults 4.27 kg, adult males 4.21 kg and females 4.32 kg). There was a large positive effect of set-aside with special mixtures, created for hares in large-scale farmed agrarian landscape, on hare density, bag and recruitment. In model hunting grounds with such set-asides increased the spring stock by 25 %, bag by 100 % and recruitment by 20 %. This study reveals that the management of European brown hare is not sustainable, and the population is decreasing. It is proved through the decline of harvest hares and by population dynamics parameters. Environmental improvements lead to the stabilization and increasing of requested parameters.

Drafting is a common technique to reduce the drag experienced by elite runners on races, leading to better running efficiency and energy savings. The tactic has been successfully used in previous races where world records were set, especially by Eliud Kipchoge in the 2018 and 2022 editions of the Berlin marathon. In the 2023 edition of the Chicago Marathon, Kenyan runner Kelvin Kiptum broke the Marathon record after a 2:00:35 finish. This feat becomes even more impressive by the lack of use of drafting formations, despite the availability of two pacers for the majority of the race. In this study, the drag faced by Kiptum and his pacers during the race is calculated by means of computational fluid dynamics (CFD). The performance of each runner is evaluated from an energetic standpoint, and the analysis is extended to include more efficient drafting formations. Our results indicate that, by properly using the advantages of drafting, Kiptum could have finished the race at a staggering 1:57:34, a full three minutes better than his own record and 215 seconds better than the previous world record.

Nutraceuticals comprise dietary supplements, functional foods, medicinal foods, and pharmaceuticals. However, to date all these concepts are interpreted in different ways with the rapid increasing knowledge on nutrition, medicine, and plant biotechnology changing the concepts about food, health and agriculture. What matters are the bioactive elements conveyed by foodstuffs as nutrients or non-nutrients, which interfere with human metabolism and have impact on health, aging and well-being. Food, not nutrients, is the fundamental unit in nutrition and edible mushrooms, are fungi that supply unique biological compounds, different from plant or animal origin, which significantly impact on health status. Their influence on medicinal interventions has been known and studied for many years. The role on neurodegenerative disorders has been recently investigated and their significance on many other diseases has been well demonstrated. On this note it is synthesized the more recent knowledge of some edible mushrooms and preparations on Ménière’s disease, a lifelong condition it can develop at any age, but most commonly appearing between 40 and 60 years of age.

Background: Breast cancer and other neoplasms, such as acute lymphocytic leukaemia, are a severe hazard to public health globally. L-glutamine-degrading enzymes are required for the treatment of malignancies such as acute lymphocytic leukemia and breast cancer. L-glutaminase, an amidohydrolase, has been shown to be an effective chemotherapeutic tool for treating a variety of malignancies. The aim of the study: Molecular characterization is used in the study and production of bacterial L- glutaminase as an anticancer agent from a variety of Egyptian soil locales. The type of the study: Screening experimental study. Methodology: In the current study, many bacterial isolates were tested on mineral L-glutamine agar selective medium (MGA) to evaluate if they generated L-glutaminase. The most effective positive bacterial isolates that produce L-glutaminase, however, were discovered by morphological and biochemical analysis. The primary positive isolate producing L-glutaminase was also identified utilizing molecular detection by 16S rRNA sequencing homology technique. The properties of bacteria-produced L- glutaminase were investigated. The anticancer activity was assessed with an MTT assay. Results: Sole bacterial isolates that only needed L-glutamine for metabolic nitrogen grew well on MGA. The optimal conditions for producing positive bacterial isolates were pH 7.4 and 37 ̊C. The morphological and biochemical investigations of soil samples from diverse soil conditions in Egypt revealed that Bacillus subtilis subsp. niger (ATCC 9372) was the primary positive bacterial isolate producing L-glutaminase. At a pH of 7.4 and a temperature of 37 °C, the activators KCL, ZnSO4, FeSO4, K2HPO4, and MgSO4 offered ideal conditions for defining L-glutaminase production. L-glutaminase from Bacillus subtilis was detected to be a highly bioavailable and efficient anticancer treatment. The original yield [productivity] from MGA was 6.3 U/ml, but invitro coupled transcription and translation production raised it to 89± 1 U/ml. L-glutaminase had a molecular mass of approximately 36 kDa. The purification of L-glutaminase resulted total activity of 21,883 ± 15.67 (U), specific activity of 379.14 ± 7.35 (U/mg of protein), and purification fold of 1.82 ± 3.06. The enzymatic activators Ni2+ and Mg 2+ increased L-glutaminase activity by 20%, 27%, respectively. The compound showed significant anticancer activity (IC50 = 38.72, 8.6, 6.41, 19.02, 49.83, and 9.45 μg/ml) against cancer cell lines from the liver (HepG-2), colon (HCT- 116), breast (MCF-7), lung (A-549), lymphocytic (CCL-120), and cervical (Hela). The kinetic parameters Km and Vmax were 15.2^ 10 -3 M and 119.86 μmol/ml/min, indicating a higher affinity for the substrate. The enzyme demonstrated high efficacy at pH 6.5 and temperature 35. The enzyme was thermostable at 58 ̊C for 1 hour. Conclusion: Acute lymphocytic leukemia and breast cancer are two instances of auxotrophic malignancies for which L-glutamine is the sole metabolic source, and Bacillus subtilis- derived L-glutaminase was a suitable enzyme in their treatment.

Background: The World Health Organization identifies lung and prostatic cancers as solid tumors with significant global lethality, both being auxotrophic cancers for L-arginine aminoacid. The aim of the study: The study aims to detect L-arginase-expressing bacteria from various soil environments in Egypt using 16S rRNA and characterize its anticancer activity. Methodology: A hundred samples of Egyptian grassland soil were gathered at a depth of 11–20 cm, close to wheat mills. Using fast plate assay screening and spectrophotometric analysis, the presence of bacteria generating L-arginase was verified. The major soil bacterial isolates were identified by morphological characterization, biochemical responses, and 16SrRNA sequencing methods. The anticancer activity of the test enzyme was assessed using MTT assay. Results: On the MAA medium, only the bacterial isolates capable of using L-arginine as the only metabolic source for carbon and nitrogen were cultivated. Bacillus cereus DSM 360 was shown to be the prevailing bacterial isolate generating L-arginase using molecular detection and biochemical reactions. When Co+2, Ni+2, and Mn+2 metal ions were present as co-factors, bacterial L-arginase demonstrated remarkable anticancer action against auxotrophic tumors for L-arginine. The total protein content was 0.349 mg, while total enzyme activity was 8.174 U with 61% enzyme recovery. As well as the specific activity reached 23.4212 U/mg. Using the mass spectrometer, the molecular weight of the bacterial L-arginase was revealed to be 37 KDa. The bacterial L-arginase's IC50 values were 3.12 U/ml for the lung cancer cell line, 3.91 U/ml for prostatic cancer cell line, 0.91 U/ml for acute promyelocytic leukemia cancer cell line and 2.73 U/ml for kidney cancer cell line. The enzyme under test showed kinetic characteristics of 7.36 mmol/l and 6.14 μmol/min for Km and Vmax, respectively. The half-life time (T1/2) was 90.17 min at 50°С, while being 86.53 min at 60°С. The test enzyme was thermostable at 60°С for 1 hour. Conclusion: The study showed a potential strategy by identifying and determining a newly discovered bacterial L-arginase enzyme as an anticancer agent in Egypt's soil settings.

The development of electric aircrafts is becoming an important technology for achieving the goals set by the European Commission for the reduction of gases emissions by 2050 in the aeronautical transportation system. However, there is a gap between the values of specific power in commercial electric machines and the ones required for aeronautical applications. Therefore, the search for alternative materials and non-conventional designs is mandatory. One emergent solution is using superconducting machines and systems to overcome the current limits of conventional electrical machines. This work reviews the new hybrid and all-electric aircraft tendencies, complementing it with recent research on the design and development of high specific power superconducting machines. This includes the main topologies for hybrid and all-electric aircraft, with an overview of the ongoing worldwide projects of these types of aircrafts, systematizing the main characteristics of their propulsion systems. It also includes the research on superconducting machines for the purpose of high specific power, considering the impact on the redesign of aircraft systems in the electrical, cooling, and fuel source sense.

Background: Demographic aging is a reality in developed countries, which poses a social challenge of great responsibility. Thus, numerous studies have been developed in an attempt to understand which factors best predict healthy aging. The aim of this study was to investigate and systematize literature on intervention programs that simultaneously include cognitive stimulation and physical activity, understand the importance of the use of new technology in these programs, and understand their impact on cognitive function in older adults, giving indications about their contribution to healthy aging. Methods: A narrative approach was used for extraction and synthesis of the data. Relevant studies were identified from electronic databases such as PubMed, Scopus, Web of Science and Academic Search Complete. Results: Thirty-two articles, involving 2815 participants, were identified. All selected studies were randomized controlled studies. The studies were published between 2011 and 2020. All studies included a combination of cognitive and physical interventions. Many of the studies used technology to administer the cognitive stimulation program. Conclusions: Most of the analyzed studies use new technologies in physical and cognitive interventions, demonstrating that this new form of intervention exerts lasting and stable benefits in cognition.

This article provides a comprehensive review of the intersection of 5G technology and Beyond, and Smart Grids, focusing on the potential of Vehicle-to-Fog as an industrial alternative for addressing energy efficiency challenges in data processing. This study aims to investigate relevant articles and patents to understand the collaborative potential between 5G and Smart Grids. It explores how to establish new regulatory standards within the architectural framework of 5G to facilitate decentralized data processing and remodel energy consumption patterns. The hypothesis suggests that decentralized 5G architecture and Smart Grids can be most effectively applied through vehicular fogging powered by solar energy. A combined quantitative and qualitative methodology guides the exploration of articles and patents. The study concludes by advocating for new standards that embrace decentralized 5G data processing, emphasizing the potential of Vehicle-to-Fog and the future deployment of 6G technology in Smart Grids. These advancements can significantly enhance energy efficiency in the context of 5G and pave the way for future innovations.

Cannabis has long been used for its medicinal and psychoactive properties. With the relatively new adoption of formal medicinal cannabis regulations worldwide, the study of cannabinoids, both endogenous and exogenous, has similarly flourished in more recent decades. In particular, research investigating the role of cannabinoids in regeneration and neurodevelopment has yielded promising results in vertebrate models. However, regeneration-competent vertebrates are few, whereas a myriad of invertebrate species have been established as superb models for regeneration. As such, this review aims to provide a comprehensive summary of the endocannabinoid system, with a focus on current advances in the area of endocannabinoid system contributions to invertebrate neurodevelopment and regeneration.

Amidst worsening climate change, drought stress imperils global agriculture, jeopardizing crop yields and food security, necessitating urgent exploration of sustainable methods like biopriming, harnessing beneficial microorganisms to bolster plant resilience. Recent research has revealed diverse biological compounds with versatile applications produced by Schizophyllum commune, rendering this fungus as a promising contender for biopriming applications. For the first time this study aimed to investigate,the potential of S. commune exo- (EPSH) and intra-PSH (IPSH), isolated from two strains: Italian (ITA) and Serbian (SRB) under submerged cultivation, in enhancing the resilience of Pisum sativum L. seeds through biopriming technique. Testing of seed quality of bioprimed, hydroprimed, and unprimed seeds was done using a germination test, under optimal and drought conditions. In optimal conditions, the IPSH SRB increased germination energy by 5.50% compared to the control, while the highest percentage of germination (94.70%) was shown after biopriming with PSH isolated from the ITA strain. Additionally, all assessed treatments resulted in a boost in seedling growth and biomass accumulation, where the ITA strain demonstrated greater effectiveness in optimal conditions, whereas the SRB strain showed superiority in drought conditions. The drought tolerance indices increased significantly in response to all examined treatments during the drought, with EPSH ITA (23.00%) and EPSH SRB (24.00%) demonstrating the greatest effects. Results demonstrate a significant positive influence of fungal PSH, indicating their potential as biopriming agents and offers insights into novel strategies for agricultural resilience in the face of changing environmental conditions.

Athlete’s heart is characterised by structural, functional, and electrical remodelling. During an exercise session, the heart increases the use of oxygen, which is associated with decreased vascular resistance in the lungs’ circulation. Left ventricular hypertrophy is an echocardiographic modification especially met in endurance athlete’s heart. Moreover, left atrial dilatation represents another important characteristic of endurance athletes. Electrical modulation in the athletic heart induces neurological modifications leading to sinus arrhythmia, bradycardia, early repolarisation, and first-grade atrioventricular (AV) blocks. Athletes' nutritional status involves the assimilation of macronutrients such as proteins, carbohydrates, and fats. Depending on the duration of physical exercise, ATP can be obtained in aerobic or anaerobic conditions. This systematic review aims to find correlations between different evaluative methods of cardiac adaptation and present the metabolism in performance athletes.

Mineral nutrition is essential for plant growth and interaction of plants with biotic and abiotic stresses. Mango twig-tip dieback (MTTD) is a new type of mango decline, but its impact on the trees’ mineral nutrition is unknown. This study was conducted to determine the effect of MTTD infection on the nutrient status, balance, and resorption efficiency (RE) of mango. Leaf nutrient concentrations and deviation from the optimum percentage (DOP) indices of ‘Kensington Pride’ (KP) mango trees with low (LD) and high (HD) levels of MTTD infections were analyzed to compare the foliar nutrition status and nutrient balance between the LD and HD trees. Moreover, the nutrient resorption efficiency of MTTD-infected dried leaves (RE_D) was compared with the resorption efficiency of healthy (RE_S) leaves of KP mangoes. The concentrations of the total Ca, Mg, Cu, Fe, Mn, and Zn were lower in the HD trees than in the LD trees. But the total K content was higher in the HD trees, and its DOP index was sufficient, while the total K concentration was low and deficient level in LD trees. Moreover, DOP indices for total Ca, Mn, and Zn were less deficient in LD trees than in HD trees, and overall nutrient imbalances were exacerbated in HD trees. RE_D was significantly lower than RE_S for the total N, P, S, Cu, Fe, and Zn but significantly higher than RE_S for K. The study underscores the significant influence of MTTD on the mineral nutrition of KP mangoes, revealing distinct nutrient variations between trees with low and high MTTD infection levels. These findings have important implications for mango crop management, emphasizing the need for targeted nutrient interventions to address imbalances induced by MTTD and enhance the overall health and resistance of mango trees against MTTD infection.

In this paper, we introduce the application of Type-I fuzzy inference systems (FIS) as an alternative to improve the prioritization in the FMECA analysis applied in cyber-power grids. Classical FMECA assesses the risk level through the Risk Priority Number (RPN). The multiplication between three integer numbers computes this, called risk factors, representing the severity, occurrence, and detectability of each failure mode and are defined by a team of experts. The RPN does not consider any relative importance between the risk factors and may not necessarily represent the real risk perception of the FMECA team members, usually expressed by natural language; this is the main FMECA shortcoming criticized in the literature. Our approach considers fuzzy variables defined by FMECA experts to represent the uncertainty associated with the human language and a rule base consisting of 125 fuzzy rules to represent the risk perception of the experts. To test our approach, we select a cyber-power grid previously analyzed by the authors using the classical FMECA. The results reveal our proposed fuzzy approach as promissory to represent the uncertainty associated with expert knowledge and to perform an accurate prioritization of failure modes in the context of electrical power systems.

According to statistics from the Food and Agriculture Organization, the world population will increase to about 91 million (Asia 51 million, Africa 19 million). A rise in the world’s population means an increased need for food. However, climate change has caused desertification and unpredictable weather, creating problems in the supply and demand of food. Sweet potato (Ipomoea batatas) is an alternative to solving the food problem, as it is one of the world’s most important food crops, especially in developing countries. The tuberous roots of sweet potato are usually used as staple food, animal feed, industrial material, or raw material for alcohol production. In the future, more variations of sweet potato will be needed for breeding this crop. Recently, molecular markers developed for sweet potato have demonstrated good potential for use in genetic selection. In this study, a cDNA library was constructed from the total RNA of sweet potato leaves. A total of 789 copies of the cDNA were cloned in Escherichia coli by employing the pGEM-T Easy vector. Sequencing was carried out by Solgent Co. (Korea). As many as 579 expressed sequence tag–simple sequence repeat (EST-SSR) markers were designed (73.38%) from the known cDNA nucleotide base sequences. The lengths of the developed EST-SSR markers ranged from 100 to 499 bp (average length 238 bp). Their motif sequence types were varied, with most being dinucleotides and pentanucleotides, and the most commonly found motifs were CAGAAT (29.0%) and TCT (2.8%). Based on these SSR-containing sequences, 619 pairs of high-quality SSR primers were designed using WebSat and Primer3web. The total number of primers designed was 144. Polymorphism was evident in 82 EST-SSR markers among 20 Korean sweet potato cultivars tested and in 90 EST-SSR markers in the two parents of a mapping population, Yeseumi and Annobeny. In this study, the hexaploid sweet potato (2n = 6x = 90) EST-SSR markers were developed in the absence of full-sequence data. Moreover, by acting as a molecular tag for particular traits, the EST-SSR marker can also simultaneously identify information about the corresponding gene. These EST-SSR markers will allow the molecular analysis of sweet potato to be done more efficiently. Thus, we can develop high-quality sweet potato while overcoming the challenges from climate change and other unfavorable conditions.

The integration of bacteriophages, a particular class of viruses that specifically infect bacteria and archaea, in biosensors for the monitoring of pathogens in foods and beverages is highly desirable. To this end, an increasing focus has been set on the exploration of covalent and physical methods for the immobilization of phages on solid surfaces. This work investigates the electrostatic assembly of tailed phages, specifically anti-Listeria monocytogenes P100 phages, on an ultrathin self-assembled monolayer (SAM) of 11-amino-1-undecanethiol (AUT). The cationic properties of AUT may allow for the electrostatic capture of P100 in a capsid-down fashion, thus, exposing the specific receptor-binding proteins on their tails to the corresponding pathogens in analytical samples. The physical properties of immobilized phages have been studied using AFM, SEM, and electrochemical techniques, providing insight into the orientation of the phages and revealing that the pH plays a remarkable role in the morphology and charge transfer behavior of the adsorbed films. Overall, this research portrays SAMs of amino-akylthiols as a valid platform for the oriented immobilization of bacteriophages on surfaces for electroanalytical purposes.

Biphasic oily/water nanoemulsions have been proposed as delivery systems for the intranasal administration of curcumin (CUR) and quercetin (QU), due to their high drug entrapment efficiency, the possibility of simultaneous drug administration and protection of the encapsulated compounds from the degradation. To better understand the physicochemical and biological performance of the selected formulation simultaneously co-encapsulating CUR and QU, a stability test of the compounds mixture was firstly carried out using X-ray powder diffraction and thermal analyses, such as differential scanning calorimetry (DSC) and thermogravimetric analyses (TGA). The determination and quantification of the encapsulated active compounds was then required being an essential tool for the development of innovative nanomedicines. Thus, a new HPLC–UV/Vis method for the simultaneous determination of CUR and QU in the nanoemulsions and their evaluation in stability studies in simulated biological fluids was developed and validated. The X-ray diffraction analyses demonstrated that no interaction between the mixture of active ingredients, if any, is strong enough to take place in the solid state. Moreover, the thermal analysis demonstrated that the CUR and QU are stable in the nanoemulsion production temperature range. The proposed analytical method for the simultaneous quantification of the two actives was selective and linear for both compounds in the range of 0.5 – 12.5 µg/mL (R2 > 0.9997), precise (RSD below 3%), robust and accurate (recovery 100 ± 5 %). The method was validated in accordance with ICH Q2 R1 “Validation of Analytical Procedures” and CDER-FDA 2validation of chromatographic methods” guideline. Furthermore, the low detection (LOD < 0.005 µg/mL for CUR and <0.14 µg/mL for QU) and quantification limits (LOQ < 0.017 µg/mL for CUR and < 0.48 µg/mL for QU) of the method were suitable for the application to drug release and permeation studies planned for the development of the nanoemulsions. The method was then applied for the determination of nanoemulsions CUR and QU encapsulation efficiencies (> 99%), as well as for the stability studies of the two compounds in simulated biological fluids over time. The proposed method represents, to our knowledge, the only method for the simultaneous quantification of CUR, and QU in nanoemulsions.

This comprehensive review is devoted to an under-exploited family of phenolic compounds, the coumarins, and the most relevant strands in which they are involved in some spirit beverages – wine spirit, brandy, whiskey, sugar cane spirits (rum and cachaça) and grape marc spirit – with great importance worldwide in terms of production, trade and consumption. It gathers the key discoveries on the topic considering the production process of each spirit beverage, the related sources of coumarins (different kinds of wood used in the ageing stage) along with the factors that govern them and can influence the sensory properties of the aged beverages. An overview of the analytical methods available for their identification/quantification is also included, as well as the corresponding trends for the advancement of knowledge in this field. Moreover, the remarkable role of coumarins as nutraceuticals, their importance as chemical markers for authenticity purposes, and their relationship with food safety of these spirit beverages are also addressed, highlighting the current gaps and issues, and providing clues for future research.

Chronic wounds remain a significant clinical challenge, necessitating the exploration of novel therapeutic agents. Sedum telephium L. (syn. Hylotelephium telephium (L.) H. Ohba) leaf juice, known for its traditional medicinal uses, was evaluated for its wound healing properties. This study aimed to chemically characterize the leaf juice and assess its efficacy in promoting wound healing in vitro. Fresh leaves were collected and processed to obtain the juice, which was analyzed for polyphenols, flavonoids, polysaccharides, and proteins. Key bioactive compounds, including flavonols such as kaempferol glycosides and quercetin glycosides, were identified. The juice and its polysaccharidic fraction were tested on human keratinocytes (HaCaT) and fibroblasts (HFF-1) to assess cell viability, wound closure, and the production of growth factors and pro-collagen I. Our results indicated that the whole juice significantly enhanced wound closure in both cell types, with a marked increase in fibroblast growth factor (FGF) and LAP(TGF-β1) production in keratinocytes, highlighting its potential mechanisms of action. The polysaccharidic fraction alone showed limited efficacy, emphasizing the importance of the complete phytocomplex. These findings suggest that Sedum telephium L. represents a promising candidate in the setting of skin regeneration and repair.

Nowadays the dynamism induced by the constant change of strategic decisions on the markets produces an extra difficulty in the management of an organization. The strategic decisions made by managers can become obsolete in a short period of time. One of the major difficulties in managing a commercial organization is to predict, with some precision degree, the impact some strategic decisions have on the financial results. Business Intelligence (BI) is an area widely used to help managers to make strategic decisions. But the methods used, behind the scenes, to achieve the conclusions are kept secret by BI company-based services. Modelling the environment can be a good option to study the impact of an action, provided by a strategic decision, in a real environment. A good model should give an approximate result of an action applied to a previous state of the environment. Artificial Neural Networks (ANNs) are proven to be excellent in modeling environments with some level of data noise. The same strategic action can have different results in different organizations. A tool that allows an evaluation of a strategic action applied to an environment should have a major importance in the management scope. Modeling the environment should save time and money for the organization to improve the performance of the strategic plan. If one evaluates the state of the environment after a strategic action being applied, it can be possible to mitigate the risk of failure of the strategic plan. As we will be able to verify, it is possible to use ANNs to model strategic environments that should allow the prediction of sales and operating results by the used strategies with some precision, although the level of success will be directly related with the user’s necessity.

L-gulonolactone oxidase enzyme (GULO) catalyzes the last step of L-ascorbic acid (vitamin C) biosynthesis. This enzymatic activity is lost in primates. The full-length rat GULO has been previously produced in plants and demonstrated to be active. In this study, we compare activity of two variants of GULO produced in Escheriachia coli cells, full-length rat GULO (fGULO) and its C-terminal catalytic domain (cGULO). The expression and purification of the recombinant proteins were optimised and their biological activity was confirmed by two methods, the GULO activity assay in the protein extracts and the ‘in-gel’ staining for GULO activity. Both variants of recombinant GULO were biologically active in both assays. However, cGULO is more promising than fGULO for ascorbic acid production because it is more efficiently produced by bacteria.

In this paper, we propose an imagined speech-based brain wave pattern recognition using deep learning. Multiple features were extracted concurrently from eight-channel Electroencephalography (EEG) signals. To obtain classifiable EEG data with fewer number of sensors, we placed the EEG sensors on carefully selected spots on the scalp. To decrease the dimensions and complexity of the EEG dataset and to avoid overfitting during the deep learning algorithm, we utilized the wavelet scattering transformation. A low-cost 8-channel EEG headset was used with MATLAB 2023a to acquire the EEG data. The Long-Short Term Memory Recurrent Neural Network (LSTM-RNN) was used to decode the identified EEG signals into four audio commands: Up, Down, Left, and Right. Wavelet scattering transformation was applied to extract the most stable features by passing the EEG dataset through a series of filtration processes. Filtration has been implemented for each individual command in the EEG datasets. The proposed imagined speech-based brain wave pattern recognition approach achieved a 92.50% overall classification accuracy. This accuracy is promising for designing a trustworthy imagined speech-based Brain-Computer Interface (BCI) future real-time systems. For better evaluation of the classification performance, other metrics were considered, and we obtained 92.74%, 92.50% and 92.62% for precision, recall, and F1-score, respectively.

Currently, in a context of biorefinery and bioeconomy, lignocellulosic biomass is increasingly used to produce biofuels, biochemicals and value-added products. Microwaves and ultrasounds are emerging techniques that enable efficient and environmentally more sustainable routes in the transformation of lignocellulosic biomass. This review is divided into four parts. In Part I, the theoretical foundations of microwaves and ultrasounds are revisited. Dielectric constants for biomass, factors that influence pre-treatment, are some of the subjects addressed. In Part II, the effects that these technologies have on lignocellulosic biomass (on the size and surface area of the particle; on the content of lignin, hemicellulose and cellulose; on the crystallinity index of cellulose; on the effect of solubilization of organic matter; on hydrolysis and reduction of sugars) are analyzed. In Part III, emphasis is given on how microwaves and ultrasounds can contribute to the achievement of value-added products. In this context, several examples of liquefactions and extractions are presented. Part IV describes examples of sonocatalysis of lignocellulosic biomass to obtain value-added products such as for instancethe production of furfural, which is significantly reduced by ultrasound.

Background: The 2021 “Universal Definition of Heart Failure (HF)” Proposed the following left ventricle ejection (LVEF) phenotype classification: ≤40%; HF with intermediate LVEF: between 41-49% and HF with preserved LVEF: ≥50%. LVEF represents the percentage of left ventricular ejected volume in each cardiac cycle and Cut-points considered statistically normal are: ≥52% in men and ≥54% in women. The prevalence HFpEF is of 35-60% among the HF phenotypes, with a facing to increase rates in relation to HFrEF and is associated with mortality rates similar to those of HFrEF. The pathophysiology of HFpEF is based on vascular and metabolic dysfunction, therefore, there is less neurohumoral stimulation compared to HFrEF. Methodology: A systematic review was performed to report of information related to Sacubitril-valsartan and the treatment of HFrEF. Terms related to “treatment” and “brazil” were used in the databases PubMed (MEDLINE) and Scientific Electronic Library Online (SCIELO). Results: Clinical trials testing drugs that modulate the neurohumoral system in patients with HFpEF failed to demonstrate benefit in the combined endpoint of reduced mortality/hospitalization due to HF compared to placebo to date. Sacubitril-valsartan is a drug with a mechanism of action surrogate the pathophysiological concept of HFpEF, it is safe and decreased endpoints of natriuretic peptides and left atrial structure in a phase II clinical study. Conclusions: The PARAGON-HF trial demonstrated that sacubitril-valsartan reduced the primary endpoint of the study when assessed the pre-specified subgroup of LVEF≤57% and improved the secondary endpoints of performance status and renal function in the population.

Nanostructured carriers have been widely used in pharmaceutical formulations for dermatological treatment. They offer targeted drug delivery, sustained release, improved biostability, and low toxicity, usually presenting advantages over conventional formulations. Due to its large surface area, small size and photothermal properties, graphene oxide (GO) has the potential to be used for such applications. Nanographene oxide (GOn) presented average sizes of 197.6 ± 11.8 nm, and a surface charge of -39.4 ± 1.8 mV, being stable in water for over 6 months. 55.5 % of the mass of GOn dispersion (at a concentration of 1 mg mL-1) permeated the skin after 6 h of exposure. GOn dispersions have been shown to absorb near-infrared radiation, reaching temperatures up to 45.7 °C, within mild photothermal therapy temperature range. Furthermore, GOn in amounts superior to those which could permeate the skin were shown not to affect human skin fibroblasts (HFF-1) morphology or viability, after 24 h of incubation. Due to its large size, no skin permeation was observed for graphite particles in aqueous dispersions stabilized with Pluronic P-123 (Gt-P-123). Altogether, for the first time, GOn potential as a topic administration agent and for delivery of photothermal therapy has been demonstrated.

The continued success of any conventional sweet potato breeding program is limited to knowledge of the inheritance of the traits studied, such as flesh color and tuberous root shape, because it is difficult to fractionate color frequencies by visual separation. The objective was to understand the mode of inheritance of these genetic traits. The crossing blocks were established at the Research Institute of Tropical Roots and Tuber Crops (INIVIT-Cuba). Eight parental genotypes of known compatibility were selected, with contrasting phenotypic characteristics to develop seg-regating populations. To express color objectively, the CIE L*a*b* color space was used (L*: lumi-nosity; a* and b*: chromatic coordinates), in addition, four morphometric variables associated with the shape and dimensions of the tuberous roots were evaluated. From 2419 reciprocal cross-es, 2045 botanical seeds and 1764 seedlings were obtained. Incomplete dominance of the white and purple flesh colors over the orange color was observed, as well as transgressive segregation for purple, orange and white flesh colours, and for the shape of the tuberous roots. The results al-lowed to propose a genetic model of biparental crosses to improve the flesh color of I. batatas, as well as a predictive formula of the progenies to be selected.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

Camelina (Camelina sativa L.) is an oilseed with potential for use as a raw material in second-generation biofuels. Camelina has a seed yield of up to 2380 kg ha^-1 and contains around 45% fatty acids. Selection of a suitable site is critical for production optimization. The objective of this study was to determine Chilean agro-climatic suitability for establishing camelina as a productive alternative. Climate and soil requirements and geographical restraints were evaluated for the species, considering the climatological characteristics of its regions of origin, as well as regions where camelina is successfully grown in the rest of the world. The variables considered include factors (maximum temperatures of the warmest month, water deficits, and degree days) and limitations (altitude, geomorphology, and current land use), which permitted the evaluation of the national territory for a certain level of suitability. It was determined that 1.3% of the national territory (960,664 ha) has some degree of suitability for camelina adoption. Between the Biobío and Los Lagos regions, 49.0% of land (471,203 ha) is in the category of without thermic restrictions, with mild water restrictions, and mild soil restrictions or without information, which can be used for camelina production. The Los Ríos region had 21.4% surface area (321,176 ha) with some level of suitability for camelina, the most suitable region to establish this crop in Chile.

Background: Gingival enlargement is defined as an abnormal overgrowth of gingival tissues. A case of a 34–year–old female presenting with maxillary chronic inflammatory gingival enlargement associated with a nickel wire allergy is reported here. Replacement of the wire, good oral hygiene therapy and surgical therapy was carried out to provide a good aesthetic outcome. Histopathological evaluation was done of the excised specimen. There is only one similar case reported in literature to the best of our knowledge and ours is the second case. Result: A Histopathological diagnosis of inflammatory fibrous hyperplasia was established. No recurrence was reported at the end of 1 year. Conclusion: The patient should be made aware of the allergy at the initial visit and oral hygiene instructions should be reinforced at every visit. The significance of patient compliance during and following therapy as an important factor in the success of treatment.

Cultivated adlay or Job’s tear (Coix lacryma-jobi L.) is an important food crop having numerous therapeutic and nutraceutical health benefits. Our study aimed to determine nutrients, minerals, fatty acid composition, and functional groups of seven wild Adlay accessions (brown, black, yellow, grey, green, off-white, and purple) to find out their scope as cereal crops using simple, rapid, and modern analytical techniques. Results revealed variations among bulk densities, specific densities, percent empty spaces, and corresponding grain counts per 10g of sample are valuable characteristics in distinguishing the accessions. Contents of fat, protein, ash, and fibre were found to be comparable to cultivated Adlay. Brown adlay was measured with the highest protein, fat, and fibre contents, 15.82%, 4.76% and 2.37%, respectively. Phosphorus, potassium, calcium, and sodium ranged 0.3% - 2.2%, whereas boron, iron, copper, zinc, and manganese were in the range 1.6mg/kg - 20.8mg/kg. Wild adlay triglyceride composition constituted of polyunsaturated fatty acids as primary fraction followed by olein and palmitic acid as prominent fatty acids. Distinguishing functional groups expressed infra-red frequencies in narrow bands and fingerprint region of proteins associated with out-of-plane region evident structural differences among adlay accessions. Frequency of functional groups in seven accessions indicated black genotype promising for varietal development.

This study delves into the impact of contrasting management practices on epiphytic bryolichenic communities, shedding light on their divergent responses to management regimes on Castanea sativa orchards. Lichens and bryophytes were sampled in managed and abandoned plots, in 95 trees, in north and south sides and at two heights in Galicia (NW Spain). The studied groups exhibit opposing reactions to these management practices, bryophytes suffer adverse effects in managed stands, experiencing reduced cover and species richness compared to abandoned orchards, while lichens displayed heightened cover and species diversity. The size of trees, included as a covariate in our analyses, displayed no significant impact on the overall species richness of lichens or bryophytes, although it did influence the cover of specific functional traits. These differing outcomes are linked to alterations in environmental conditions brought by management interventions. Furthermore, the study uncovers divergent responses within the taxonomic and functional composition of epiphytic communities. Different species and functional groups exhibit varying reactions to changing environmental conditions, making predictions a complex endeavor. In conclusion, this research emphasizes the need for management strategies that account for the diverse ecological requirements of different species and functional groups. Since no single management regime will suit all species or functional groups.

Rosemary is one of the most important medicinal plants for natural therapy due to its multiple pharmacological properties, such as antioxidant, anti-inflammatory, neuroprotective, antiproliferative, antitumor, hepato- and nephroprotective, hypolipidemic, hypocholesterolemic, antihypertensive, anti-ischemic, hypoglycemic, radioprotective, antimicrobial, antiviral, antiallergic, wound healing. Our study reports for the first time, over a 12-month period, the identification and quantification of polyphenols and the investigation of the antioxidant and acetylcholinesterase (AChE) inhibitory activity of the Rosmarinus officinalis L. species harvested at flowering from the flora of southwestern Romania (Oltenia Region). Identification and quantification of polyphenolic acids was made by ultra-high-performance liquid chromatography/mass spectrometry (UHPLC/MS). Total phenolic content was determined using the spectrophotometric method. In situ antioxidant and anticholinesterase activity was evaluated using 2,2-diphenyl-1-picrylhydrazyl (DPPH) and AChE inhibitory assay, respectively, on high-performance thin-layer chromatography (HPTLC) plates. DPPH radical scavenging activity was also assessed spectrophotometrically. The results revealed significant correlations between specific polyphenolic compounds and the measured biological activities, understanding the role of seasonal variations and providing insights into the optimal harvesting times and medicinal benefits of rosemary. Our research brings new information on the phytochemical profile of R. officinalis, as a natural source of polyphenols with antioxidant and AChE inhibitory properties.

Groundwater is becoming increasingly important in the Pacific Northwest of the USA due to declining snowpack volumes and shifts in precipitation type and timing, all connected with climate change. The Upper Williamson Basin of the Klamath Watershed is a groundwater dominated watershed with massive fluctuations in year-to-year streamflow volumes over the past four decades, including the complete absence of any live flow for several years. The precise relationship between groundwater and streamflow in the basin has been difficult to assess due to a limited number of monitoring wells and significant gaps in the water level time history. To address this challenge, we use a novel imputation technique that leverages Earth observations and machine learning to impute gaps in water level records. We use these more complete datasets to compute a groundwater storage change time series for the basin. We show that groundwater storage is highly correlated to streamflow and that groundwater storage is correlated to rainfall with a three- to four-year delay that appears variable depending on groundwater storage volumes. The tools and relationships we present make it possible for water managers to estimate when streamflows will return to the basin and be more informed to support better management.

As Chronic Non-Communicable Diseases (CNCD) increase, preventive approaches become more crucial. In this review, Calorie Restriction (CR) effects on human beings were evaluated, comparing benefits and risks of different CR diets: classic CR vs ketosis-inducing diets, including Intermittent Fasting (IF), Classic Ketogenic Diet (CKD), Fasting Mimicking Diet (FMD), Very-Low-Calorie Ketogenic Diet (VLCKD) and Spanish Ketogenic Mediterranean Diet (SKMD). Special emphasis on Insulin Resistance (IR) was placed, as it mediates Metabolic Syndrome (MS), a risk factor for CNCD, and predicts MS diagnosis. CR is the most robust intervention known to increase lifespan and health span, with high evidence and known biochemical mechanisms. CR improves cardiometabolic risk parameters, boosts exercise insulin sensitivity response, and there may be benefits of implementing moderate CR on healthy young and middle-aged individuals. However, there is insufficient evidence to support long-term CR. CKD is effective for weight and MS management, and may have additional benefits such as prevention of muscle loss and appetite control. SKMD has extreme significance benefits for all the metabolic parameters studied. Studies show inconsistent benefits of IF compared to classic CR. More studies are required to study biochemical parameters, reinforce evidence, identify risks, and seek effective and safe nutritional CR approaches.

A substantial amount of phosphorus (P) in soil is not readily available for plant uptake. Certain species may enhance P availability from poorly soluble P forms. This research aimed to compare the P solubilization capacity of the soil of two Lupine species, L. albus, and L. angustifolius, with a control crop of oats (Avena strigosa L.). Plants were planted in pots in four soils with varying texture, organic matter content, acidity, and P availability. Phosphorus solubilization capacity was assessed on variations of P availability (PBray1) at four points in time, comparing soils with lupine to oat-containing soils and their baseline values. At harvest, measurements of plant shoot biomass included their shoot dry weight and some nutrient concentrations such as P, nitrogen (N), manganese (Mn), and lupine nitrogen fixation. Compared to soils containing oats, lupine soils significantly increased PBray1 concentrations; increments ranged from 0.9 to 5.4 mg kg-1, depending on species, sampling time, and soil type. Lupine-induced soil acidification did not fully explain this P increase., As a proxy measurement of organic acid exudation, Manganese concentration was high in both lupine species' shoot biomass; however, these legumes had divergent Mn accumulation responses to soil acidity and P availability. Nitrogen fixed quantity varied with Lupine species (105-240 mg pot-1) and soil type (60-240 mg pot-1). Lupinus albus had a higher ability to mobilize non-labile P and provide N through biological N fixation (BNF), positioning it as a suitable crop for diversifying Uruguay's agricultural crop rotation systems.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

High Brassicaceae consumption reduces the risk of developing several cancer types, probably due to their glucosinolate amount. Extracts from Sinapis nigra L. and Sinapis alba L. have been obtained from leaves and seeds under different conditions using ethanol/water mixtures because well accepted by food industry. The EtOH/H2O 8:2 mixture gives better yields in glucosinolate amounts from grinded seeds, mainly sinalbin in S. alba and sinigrin in S. nigra. The highest antiproliferative activity in both non-tumour and tumour cell lines was induced by S. alba seeds extract. To evaluate whether Sinapis spp effect was only due to glucosinolate content or it was influenced by the extracts’ complexity, cells were treated with extracts or glucosinolates, in the presence of myrosinase. Pure sinigrin did not modify cell proliferation, while pure sinalbin was less effective than the extract. The addition of myrosinase increased the antiproliferative effects of the S. nigra extract and sinigrin. Antiproliferative activity was correlated to MAPKs modulation, which was cell and extract-dependent. Cell-cycle analysis evidenced a proapoptotic effect of S. alba on both tumour cell lines and of S. nigra only on HCT 116. Both extracts showed good antimicrobial activity in disc diffusion tests and on ready-to-eat fresh salad. These results underline the potential effects of Sinapis spp in chemoprevention and food preservation.

The interest in flying wings dates as far the early years of the aviation age. Over the 20th century, numerous attempts were made to investigate the feasibility of the concept, which demonstrated numerous early benefits: increased aerodynamic efficiency, reduced fuel consumption and lower noise and pollutant emissions compared to conventional tube and wing aircraft. However, major technical challenges prevented that type of design from entering mass production, especially with regards to structural design and manufacturing, stability and control and ride quality. In the 1990’s, a new concept, the blended wing body (BWB), was created to alleviate some of the concerns of flying wings while maintaining increased efficiency. Despite the promise, technical hurdles once again proved to be a deal breaker, and as of 2024, the only flying wing to enter serial production is the B-2 Spirit, an extremely complex and expensive aircraft. Thirty years later, as the world is quickly transitioning towards cleaner energy, the interest in the blended wing body has been renewed. The latest technological advancements in the aerospace industry should make the development of the BWB more plausible, however passenger comfort issues remain. Surprisingly, the BWB development may come from an unexpected application: as a tanker aircraft. As the U.S. Air Force is seeking a replacement to hundreds of aging tankers, a startup company was recently funded to develop the concept and build a prototype. In this study, we explore the history of blended designs from its early days, highlighting its opportunities and challenges – and why the design is an intriguing fit for application as a tanker aircraft.

Single-particle cryo-electron microscopy (cryo-EM SPA) has recently emerged as an exceptionally well-suited technique for determining the structure of membrane proteins (MPs). Indeed, in the last years, it was observed a huge increase in the number of MPs solved by cryo-EM SPA at a resolution better than 3.0 Å in the Protein Data Bank (PDB). However, sample preparation remains a significant challenge in the field. Here, we evaluated in the MPs solved by cryo-EM SPA deposited in the PDB in the last two years at a resolution below 3.0 Å the most critical parameters for sample preparation: i) the surfactant used for protein extraction from the membrane, ii) the surfactant, amphiphiles, nanodiscs or other molecules present in the vitrification step, iii) the vitrification method employed, and iv) the type of grids used. The aim is not to provide a definitive answer on the optimal sample conditions for cryo-EM SPA of MPs, but rather assess the current trends in the MP structural biology community towards obtaining high-resolution cryo-EM structures.

Background: Pediatric forearm fractures represent a substantial proportion of childhood injuries, requiring effective and minimally invasive treatments. Our study investigated the mid-term outcomes of biodegradable poly-L-lactide-co-glycolide (PLGA) intramedullary implants in managing diaphyseal forearm fractures in children. Methods: A follow-up cohort study was conducted with 38 patients treated with PLGA implants. Control examinations were performed one year post-operation, assessing bone healing through radiographic evaluations and functional outcomes using injured and uninjured limb range of motion (ROM) comparisons. Scarring was evaluated employing the Vancouver Scar Scale (VSS), and satisfaction via a questionnaire. Results: Children were predominantly female (76.4%), with a mean age of 9.71 (SD: 2.69) years. Effective fracture stabilization and bone healing were found in all patients, with a minor reduction (mean difference of -1.5°, p = 0.282) in elbow flexion on the operated side (139.3°) compared to the intact (140.8°). Elbow extension presented negligible average changes (0.2°, p= 0.098). Forearm movements were slightly reduced on the operated side (mean pronation: 80.8° vs. 83.7°, p= 0.166; average supination: 83.5° vs. 85.7°, p= 0.141). Wrist palmar flexion and dorsiflexion showed no significant differences. VSS ratings indicated minimal scarring (mean guardian and doctor scores were 1.13 and 0.55, respectively, p= 0.020), and all patients reported satisfaction with the treatment outcomes. Conclusion: Biodegradable implants are effective for pediatric forearm fractures, providing stable bone healing while preserving functional ROM with minimal scarring and high patient satisfaction. PLGA proved to be a viable alternative to traditional metal implants, eliminating secondary removal surgeries.

Although the water absorption feature (WAF) at 970 nm is not very well-defined, it may be used alongside other indices to estimate the canopy water content. The individual performance of a number of existing vegetation water content (VWC) indices against the WAF is assessed using linear regression model. We developed a new Combined Vegetation Water Index (CVWI) by merging indices to boost the weak absorption feature. CVWI showed a promise in assessing the vegetation water status derived from the 970 nm absorption wavelength. CVWI was able to differentiate two groups of dataset when regressed against the absorption feature. CVWI could be seen as an easy and robust method for vegetation water content studies using hyperspectral field data.

The research was aimed at comparing the fire characteristics of different types of pepper in the context of designing explosion prevention. The following characteristics were studied: explosion pressure pmax and Kst at selected concentrations, ignition temperature of the deposited dust layer from the hot surface and minimum initiation energy. The comparison of the chemical properties of the used types of pepper was performed using TG/DSC. Results of the measurements suggest that different types of peppers exhibit different explosion characteristics. Each of the samples reached the maximum value of the explosion pressure, and their rate of pressure rise increased at different concentrations. The volume of the explosion chamber used also influenced the explosion characteristics. It is a consequence of the fact that the explosion characteristics strongly depend on the mechanism of action of a particular igniter. The minimum effect on the safety characteristics was observed when measuring the minimum initiation energy and the minimum ignition temperature of dust layer from the hot surface. The results of the measurements suggest that different types of peppers exhibit different explosion characteristics. This information should then be considered in explosion prevention.

(1) Background: Nicotine is implicated in the SARS-COV-2 infection through activation of the α7-nAChR and over-expression of ACE2. Our objective is to clarify the role of nicotine in SARS-CoV-2 infection exploring its molecular and cellular activity. (2) Methods: HBEpC or si-mRNA-α7-HBEpC were treated for 1, 48 h or continuously with 10-7 M Nicotine, a concentration mimicking human exposure to a cigarette. Cell viability and proliferation were evaluated by trypan blue dye exclusion and cell counting, migration by cell migration assay, senescence by SA-beta-Gal activity, and anchorage-independent growth by cloning in soft agar. Expression of Ki67, p53/phospho-p53, VEGF, EGFR/pEGFR, phospho-p38, intracellular Ca+2, ATP and EMT were evaluated by ELISA and/or western blotting. (3) Results: Nicotine induced through α7-nAChR (i) increase in cell viability (ii) cell proliferation; (iii) Ki67 over-expression, (iv) phospho-p38 up-regulation (v) EGFR/pEGFR over-expression; (vi) increase in basal Ca+2 concentration, (vii) reduction of ATP production; (viii) decreased level of p53/phospho-p53, (ix) delayed senescence, (x) VEGF increase, (xi) EMT and consequent (xii) enhanced migration, and (xiii) ability to grow independently of the substrate. (4) Conclusions: Based on our results and on evidence showing that Nicotine potentiates viral infection it is likely that Nicotine is involved in SARS-CoV-2 infection and severity

Background: Breast cancer and other neoplasms like acute lymphocytic leukemia pose a serious threat to public health worldwide. Treatment for malignancies including acute lymphocytic leukemia and breast cancer requires enzymes that break down L-glutamine. An amidohydrolase called L-glutaminase can be an effective chemotherapeutic tool for treating various cancers. Methods: On mineral L-glutamine agar selective medium (MGA), a few bacterial isolates were examined in the current investigation to see if they produced L-glutaminase. However, the most effective positive bacterial isolates generating L-glutaminase were identified using morphological and biochemical testing. Molecular detection using the direct Southern blotting approach was also used to determine the main positive isolate that produces L-glutaminase. L-glutaminase synthesis by bacteria was evaluated for its characteristics. Using an MTT test, the anticancer activity was evaluated. Results: exclusive bacterial isolates that used L-glutamine as their sole source of metabolic nitrogen exhibited favorable growth on MGA. PH 7.4 and a temperature of 37 0C were the ideal environmental and physiological conditions for developing positive bacterial isolates. From the soil samples taken from various soil conditions in Egypt, the morphological and biochemical analyses showed that Bacillus cereus 14579 was the main positive bacterial generating L-glutaminase isolate. At a pH of 7.4 and a temperature of 37 °C, the following activators—KCL, ZnSO4, FeSO4, K2HPO4, and MgSO4—provided the high-grade circumstances for characterizing L-glutaminase synthesis. Bacillus cereus-produced L-glutaminase has shown excellent bioavailability and effectiveness as an anticancer therapy. The yield [productivity] was 5.2 U/ml during the original manufacture from MGA, but it increased to 42.96 U/ ml by bacterial recombinant DNA manufacturing. The molecular mass of L-glutaminase was roughly 37 KDa. L-glutaminase was purified, yielding final enzyme recovery of 55 1.23%, total activity 12,990± 19.76 ( U), specific activity 384.66± 8.92( U/ mg of protein), and purification fold 2± 2.99. Furthermore, the L-glutaminase activity was raised by 19%, 23%, 15%, and 9%, respectively, by the enzymatic activators Mn2+, K+, Na+, and Fe3+. It demonstrated strong DPPH scavenging activity (IC50 = 61 μg/ mL) and anticancer activity( IC50 = 40.72, 9.7, 7.39, 20.61, 51.28, and 11.55 μg/ mL, respectively) against human liver (HepG-2), colon ( HCT-116), breast ( MCF-7), lung( A-549), lymphocytic( CCL-120), and cervical( Hela) cancer cell lines. A stronger affinity for its substrate was shown by the kinetic parameters of Km and Vmax, which were 13.2 10-5 M and 119.86 μmol/ ml/ min, respectively. Conclusion: Acute lymphocytic leukemia and breast cancer are examples of auxotrophic malignancies for which L-glutamine serves as the only metabolic source, and L-glutaminase generated by Bacillus cereus was an appropriate enzyme in the therapy of these diseases.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

The microbioma is presently one of the hottest areas of scientific and medical research and exerts a marked influence on the host during homeostasis and disease. Fermented foods arise in the human relationship to the microbial environment. Further to the traditionally recognized effects of fermented foods and beverages on the digestive health and well-being there is now strong evidence on their general health benefits, namely the significance on the gut microbiota and brain functionality. We highlight the possibilities in this field, how little is still known, and call for a convergence of interdisciplinary research fields of One Health microbe-nutrition with fermented foods and gut-brain research. A consequence of civilisation, changes in present-day society in diets with more sugar, fat and salt, habits and lifestyle, contributes to the likelihood of an inflammatory microbiome, particularly the global epidemics of obesity and mental health. Although two recent papers claim that probiotics perturb rather than aid in microbiota recovery back to baseline after antibiotic administration in humans, consuming fermented foods has shown to reduce inflammation so improve gut health and the proper function of the body’s immune system.

The G-protein-coupled estrogen receptor (GPER; G protein-coupled estrogen receptor 30, also known as GPR30) is a novel estrogen receptor and has emerged as a promising target for ovarian cancer. GPER, a seven-transmembrane receptor, suppresses cellular viability and migration in studied ovarian cancer cells. However, its impact on the fallopian tube, which is the potential origin of high-grade serous (HGSC) ovarian cancer, has not been addressed. This study was conducted to evaluate the relationship of GPER, ovarian cancer subtypes, i.e., high-grade serous cell lines (OV90 and OVCAR420), as well as potential HGSC ovarian cancer origin (i.e., the fallopian tube cell line FT190). The selective ligand assessed here is the agonist G-1, which was utilized in an in vitro study to characterize its effects on cellular viability and migration. As a result, this study has addressed the effect of a specific GPER antagonist in combination with an agonist on cell viability, providing a better understanding of the effects of these compounds on our diverse group of studied cell lines. Strikingly, attenuated cell proliferation and migration behaviors were observed in the presence of G-1. Thus, our in vitro study reveals the impact of the origin of HGSC ovarian cancers and highlights the GPER agonist G-1 as a potential therapy for ovarian cancer.

The study involved a comparison of the chemical, physical, microbiological, and functional attributes of must extracted from Solaris cultivar grapes cultivated under both conventional and organic farming systems. This study aimed to determine the influence of cultivation methods on various must properties, including the levels of health-promoting polyphenols and health-threatening mycotoxins and pesticide residues. It was observed that the organic grapes hosted a greater diversity and quantity (OTUs) of bacteria and fungi. The predominant bacteria were Sphingomonas (with similar numbers in both crops) and Massilia (more abundant in grapes from the conventional crop). These two bacterial groups collectively accounted, on average, for about 40% of all OTU sequences detected. Lower levels of bacteria of the genera Hymenobacter and Pseudomonas and others colonized the grapes. Among the fungi, Erysiphe and Aureobasidium were dominant, comprising about 50–70% of all detected taxa. Notably, Erysiphe was predominantly found in conventionally grown grapes, while Aureobasidium, Mycosphaerella, and Botryotinia were present in comparable quantities in fruit from both types of crops. No mycotoxins were detected in the must or marc, despite the presence of genes responsible for aflatoxin and ochratoxin biosynthesis in both types of grape juice. The organic must exhibited significantly higher levels of polyphenols and displayed improved antioxidant properties and technological characteristics. Moreover, sulfur and copper used in the protection of the organic plantation passed from the fruit surface into the must. Also, pesticide residues, namely cyprodinil and fludioxonil from conventional cultivation, were detected in the must.

Integrated nutrient management (INM) is an approach that optimizes the benefits derived from various nutrient sources and beneficial soil microorganisms in an integrated manner to increase crop productivity while maintaining soil fertility. An open-field experiment was conducted at Cabuyao, Laguna, Philippines to investigate the effects of combining chemical fertilizers, vermicompost, arbuscular mycorrhizal fungi (AMF), and nitrogen-fixing bacteria (Azospirillum spp.) on the growth, nutrient uptake and yield of tomato. The experiment was arranged in a randomized complete block design replicated four times. The treatments were recommended rate of chemical fertilizer (RRC), combined 50% RRC and 4 t ha-1 vermicompost (INM 1), AMF inoculation with combined nutrient sources (INM 2), and dual inoculation with AMF and Azospirillum in synergy with combined nutrient sources (INM 3). Results revealed that the growth parameters were not significantly affected by the treatments, but the highest data were observed in the treatments under INM. AMF inoculation significantly increased phosphorus, potassium, calcium, and magnesium uptake of tomato while INM 3 recorded the highest nitrogen uptake. Treatments with vermicompost application recorded significantly higher uptake of copper. INM 1, INM 2, and INM 3 gave a significantly higher fruit yield than the RRC with an increase of 7.98%, 13.40%, and 13.65%, respectively. The percentage of mycorrhizal root colonization and number of rhizosphere spores were higher in mycorrhizal plants. Fruit yield and AMF root colonization are positively correlated with uptake of various nutrients. The results imply that these INM strategies can improve growth of tomato, increase fruit yield, reduce the amount of chemical fertilizers applied, and potentially lead to economic, soil health and environmental benefits.

Eicheon properties are discussed. It is shown that the eicheon surface allows setting a boundary condition for the vacuum polarization and obtaining a solution describing the dark matter tail in the Milky Way. That is, the dark matter in the Milky Way is explained as the F-type of vacuum polarization, which could be treated as dark radiation. The model presented is spherically symmetric, but a surface density of a baryonic galaxy disk is taken into account approximately by smearing the disk over a sphere. This allows the reproduction of the large distance shape of the Milky Way rotational curve. Andromeda's rotational curves are also discussed.

Hazelnut shells (HS), scientifically known as Corylus avellana L. shells, are a waste produced in companies that process nuts. The main objective of this study was to find an efficient way to maximize the chemical potential of HS by solubilizing the hemicelluloses, which could then be used to recover sugars and at the same time increase the lignin content of this material in order to produce adhesives or high strength foams. In order to optimize the pre-hydrolysis process, two different temperatures (160 and 170 C) and times varying from 15 to 180 min were tested. All the remaining solid materials were then liquefied by polyalcohols with acid catalysis. The chemical composition of hazelnut shells was determined before and after the pre-hydrolysis. All the process was monitored by FTIR-ATR by determining the spectra of solids and liquids after pre-hydrolisis and liquefactions steps. The highest solubilization of hazelnut shells was found for 170 C and 180 min, resulting in a 25.8% solubilization. Chemical analysis after the hydrolysis process showed a gradual increase in the solubilization of hemicelluloses as both the temperature and time of the reactor were increased. Simultaneously, the percentages of α-cellulose and lignin in the material also increased with rises in temperature and duration. FTIR-ATR allowed for the detection of significant spectral changes in the hazelnut shells from their initial state to the solid residue and further into the liquefied phase. This confirmed that pre-hydrolysis was effective in enhancing the chemical composition of the material, making it more suitable for the production of adhesives or polyurethane foams with enhanced mechanical strength.

We present synthetic experiments of lactic acid (LA) polycondensation to produce poly(lactic acid) (PLA), as well as kinetic modeling calculations that capture the polymer molecular weight increase with time, given the initial concentrations. Tin-octoate-catalyzed polycondensation of (D,L)- or L-lactic acid, was carried out in pre-dried toluene after azeotropic dehydration for 48-120 hours at 130-137 °C. The polymerization was optimized by varying lactic acid and catalyst concentrations as well as the temperature. Gel Permeation Chromatography was used to experimentally follow the evolution of molecular weights and the products were characterized by NMR, TGA, DSC and IR. Under optimal conditions, PLLA with weight-average molecular weight (Mw) of 161 kDa could be obtained. The rate equations that describe polycondensation kinetics were recast in a condensed form that allowed very fast numerical solution and calculation of the number-average molecular weight with time. Deviations with respect to the experiment were minimized in a least-squares fashion, to determine rate constants. The optimized kinetics parameters are shown to reproduce the experimental data accurately

Reliability assessment in traditional power distribution systems has played a key role in power system planning, design, and operation. Recently, new information and communication technologies have been introduced in power systems automation and asset management, making the distribution network even more complex. In order to achieve efficient energy management, the distribution grid has to adopt a new configuration and operational conditions that are changing the paradigm of the actual electrical system. Therefore, the emergence of the cyber-physical systems concept to face future energetic needs requires alternative approaches for evaluating the reliability of modern distribution systems, especially in the smart grids environment. In this paper, a reliability approach that makes use of failure modes of power and cyber network main components is proposed to evaluate risk analysis in smart electrical distribution systems. We introduce the application of Failure Modes and Effects Analysis (FMEA) method in future smart grid systems in order to establish the impact of different failure modes on their performance. A smart grid test system is defined and failure modes and their effects for both power and the cyber components are presented. Preventive maintenance tasks are proposed and systematized to minimize the impact of high-risk failures and increase reliability.