Flow experience, characterized by deep immersion and complete engagement in a task, is highly recognized for its positive psychological impacts. However, previous studies have been restricted to use a single type of task, and the exploration on its neural correlates has been limited. This study aimed to explore the neural correlates of flow experience with the employment of multifac-eted flow-induction tasks. Six tasks spanning mindfulness, artistic tasks, free recall, and varying levels of Tetris complexity (easy, flow, and hard conditions) were employed to have a relatively complete coverage of the known flow-induction tasks for a better induction of individualized flow experience. Twenty-eight participants were recruited to perform these six tasks, with a sin-gle-channel prefrontal electroencephalography (EEG) recording. Significant positive correlations were observed between the subjective flow scores of individual’s best-flow-experience task and the EEG activities at delta, gamma, and theta bands, peaking at latencies around 2 minutes after task onset. The outcomes of our multiple regression analysis yield a maximum coefficient of de-termination (R²) of 0.279. Our findings report the EEG correlates of flow experience in naturalistic settings and highlight the potential of portable and unobtrusive EEG technology for an objective measurement of flow experience.

Although a lot of research has been carried out on hand sanitizer as an effort to prevent Covid-19, there is still limited research on non-alcoholic hand sanitizer lotion from the brown algae Scytosiphon lomentaria (S. lomentaria) as a raw material that provides antibacterial effects and maintains healthy skin. Therefore, this study aimed to analyze microbial inhibitory ability, physical and chemical characteristics of hand sanitizer lotion made from S. lomentaria algae. S. lomentaria powder was tested for phytochemicals, total phenolic content, free radical scavenging activity (IC50), and antibacterial tests. S. lomentaria slurry was prepared by adding distilled water (1:1) for lotion preparations in four treatment groups, such as normal control (lotion base without adding algae), lotion with the addition of algae 20%, 30%, and 40%. The lotion preparations for each treatment group were tested for antibacterial activity of Staphylococcus aureus and Escherichia coli, phytochemicals, pH, adhesion, spreadability, homogeneity, emulsion type, and hedonic. S. lomentaria powder contains bioactive polyphenolic compounds with a total phenolic content of 117.70±1.40 mg GAE/g dry weight and an IC50 value of 455±3.4 ppm, while lotion with the addition of S. lomentaria contains polyphenols and saponins The best treatment was shown by 40% S. lomentaria hand sanitizer lotion with inhibition of 6.30 ± 0.64 mm E. coli, 6.85 ± 1.12 mm S. aureus, hedonic test for color, texture and absorption with likes to likes very much level, neutral pH, greenish-white color, O/W emulsion type, high adhesion, homogeneous, and easily absorbed by the skin. This research can be an alternative reference in making non-alcoholic hand sanitizer lotion that is safe for the skin.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

Glioblastoma (GBM) is the most common malignant primary brain tumor, with a median survival rate of less than two years. Currently, there is no cure for GBM, underscoring the urgent need for innovative treatment approaches. Vaccine design emerges as a crucial strategy, offering a safe and effective means for both preventive and therapeutic interventions against GBM. In this study, we targeted four GBM-associated mutated surface proteins—urokinase plasminogen activator sur-face receptor (PLAUR), integrin beta-3 (ITGB3), and the B-41 alpha chain (HLA-B) and A-24 alpha chain (HLA-A) of the HLA class I histocompatibility antigens—to design a peptide-based vaccine. The vaccine construct includes cytotoxic T lymphocyte (CTL) and T helper cell (Th cell) epitopes, and was meticulously evaluated for antigenicity, allergenicity, and toxicity. The results indicate that the vaccine is antigenic and non-allergenic, making it a promising candidate. Additionally, the physico-chemical properties of the vaccine suggest stability and suitability for further de-velopment. Immune simulation studies predict efficient immune responses upon vaccine ad-ministration. Our vaccine shows promise as a potential tool in the fight against GBM, offering new hope for patients facing this devastating disease.

Using the data of China's A-share non-financial listed enterprises from 2015 to 2022 as a sample, this study empirically tests the impact of ESG rating disagreement on corporate debt financing cost. The results show that ESG rating disagreement significantly increases the debt financing costs of enterprises, and this result still holds after a series of robustness tests such as replacing the dependent and independent variables and PSM approach. Meanwhile, the heterogeneity analysis reveals that non-state-owned enterprises and enterprises in non-heavily polluting industries are more sensitive to ESG ratings disagreement. In addition, mechanism analysis shows that corporate financing constraints mediate the relationship between ESG rating disagreements and debt financing costs. The findings of this study provide important evidence for understanding the impact of ESG rating disagreement on the costs of debt financing, enrich the meaning of ESG rating disagreement, and reveal the significance of unifying ESG rating standards.

This research delves into librarians' perceptions of artificial intelligence (AI) support in learning experiences, lifelong learning, and digital literacy within the library context, undertaking a comparative analysis between Malaysia and Indonesia. Employing a survey methodology, a self-developed questionnaire was administered to 59 librarians in Malaysia and 85 in Indonesia. The questionnaire, utilizing a Likert scale, systematically explored subjective judgments on AI's impact across various dimensions. A noteworthy finding is the consistent and harmonized perception among librarians in both countries, underscoring a universal recognition of AI's perceived support for learning experiences, lifelong learning, and digital literacy. Of particular interest is the emphasis on sustainability in librarians' perspectives, as they recognize the enduring value of AI in fostering educational growth. Despite the limitations inherent in perceptual measures and a relatively modest sample size, the empirical and practical contributions of this study are significant. It offers a nuanced exploration of librarians' viewpoints, providing valuable insights for future research endeavors. Moreover, the study's findings have immediate practical implications for the integration of AI tools in library services, policy-making, and professional development, with a focus on ensuring sustainable implementation for long-term benefits.

Brand trust holds significant importance in the Mongolian cashmere industry. This study examines the primary predictors of customer brand trust among Mongolian cashmere users. Our research includes a survey with 800 participants and 20 individual interviews conducted among both Mongolian cashmere users and non-users. We utilized an online platform to reach participants, employing convenience sampling. The study investigates the relationship between various factors and brand trust within the context of Mongolian cashmere brands. Through a combination of in-dividual interviews and statistical analysis, we test six hypotheses. The findings indicate that higher brand quality, a strong reputation, greater transparency, effective issue resolution, commitment to environmental and social responsibility, and pre-purchase research on such commitments positively impact brand trust. Key insights gleaned from the interviews emphasize the importance of quality, reputation, transparency, customer service, and environmental responsibility in shaping consumer trust. These results offer valuable implications for cashmere brands aiming to bolster consumer trust and foster loyalty.

Excitotoxicity related to the dysfunction of the N-methyl-d-aspartate receptor (NMDAR) has been indicated to play an integral role in the pathophysiology of multiple disease states, including neurodegenerative disorders such as Parkinson’s disease. There is a notable gap in the market for novel NMDAR antagonists, however current methods to analyze potential antagonists rely on indirect measurements of calcium flux and hazardous radioligand binding assays. Recently, a fluorescent NMDAR ligand, N-adamantan-1-yl-dimethylamino-1-naphthalenesulfonic acid, known as AM-DAN was developed by our group. Additional studies on this ligand is necessary to evaluate its potential as a biological tool in NMDAR research. Therefore, this study was aimed at conducting structural analyses, fluorescence experiments, high-accuracy NMDAR molecular modelling and NMDAR phencyclidine (PCP) site competition binding studies using AM-DAN. Results revealed that AM-DAN has appropriate structural properties, significant fluorescent ability in various solvents and is able to bind selectively and compete for the PCP-binding site of the NMDAR. Therefore, AM-DAN holds promise as a novel fluorescent ligand to measure the affinity of prospective drugs binding at the NMDAR PCP-site and may circumvent the use of radioligands.

In the last decade, a higher level of reliability became a compulsory demand when it comes to modern DC-DC converters. This work addresses the main reliability metrics: the failure rate λλ and MTBF of an output capacitor bank used within a high current low voltage buck converter due to many studies have shown that the output capacitor bank was demonstrated being the most critical component within the converter. Many authors treated this issue, usually by doing reliability predictions. The majority of the papers use only one specific Standard Prediction to solve the problem. Herein calculation was done using both the older standard MIL-HDBK-217 and the latest one Telcordia SR-332, providing a benchmark comparison between the two which is a helpful tool for the output capacitor selection in the early stage design. Military standard was well accepted for decades in order to reliability prediction even on industrial electronics and is still used today under a critical manner because no more update after the latest version MIL-HDBK-217F - Notice 2 released in 1995. Since then, newer prediction standards had appeared in the electronics reliability market. Over time, this standard was mostly used but it does not accurately model the reliability because lack of taking account of mission profile. The above-mentioned newer standard – i.e., Telcordia SR-332 is trying to compensate also the lack of the newest component technology in the older standard (which is the first standard released on the market) supplying useful design data for design engineers who use the so-called “design with the reliability in mind” concept. Within the paper were established the environmental condition for the passive components by means of a PoL (Point of load) buck converter that is used for both calculation methods. The influence of temperature and several specific concepts like reference conditions, operating conditions, ripple, and internal self-heating were taking account in order to display the results. The temperature for the capacitor’s capsule needed in π_T stress factor calculation was derived by PSPICE simulation. High fidelity and dedicated SPICE models provided by the manufacturer were used for MOSFETs, polymer electrolytic, and MLCC capacitors that compose the converter.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

Small peptides (SPs), ranging from 5 to 100 amino acids, play integral roles in plants due to their diverse functions. Despite their low abundance and small molecular weight, SPs intricately regulate critical aspects of plant life, including cell division, growth, differentiation, flowering, fruiting, maturation, and stress responses. As vital mediators of intercellular signaling, SPs have garnered significant attention in plant biology research. This comprehensive review delves into SPs' structure, classification, and identification, providing a detailed understanding of their significance. Additionally, we summarize recent findings on the biological functions and signaling pathways of prominent SPs that regulate plant growth and development. The review also offers a forward-looking perspective on future research directions in peptide signaling pathways.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

In recent years, Chinese manufacturing enterprises compete to chase the wave of "digital revolution", digital empowerment has become an important strategic path of technological reform for many manufacturing enterprises. Based on the micro data of listed companies, this paper investigates the impact of digital transformation of Chinese listed companies on the quality of their export products. It is found that digital transformation can significantly improve the quality of enterprises' export products. After a series of robustness tests, this conclusion is still valid, and there are two ways to improve innovation performance and total factor productivity. The export product quality enhancement effect of enterprise digital transformation also has the heterogeneity of ownership, region and industry. In the further study, this paper also examines the impact of digital transformation on the internal salary gap of enterprises, and finds that digital transformation may increase the internal salary gap of enterprises, and form a "masking effect" on the quality of export products. To a certain extent, this paper deepens the understanding of the study of enterprise digital transformation on the quality of export products and its differences, and provides certain guidance for enterprises to implement the strategy of digital transformation.

Background: Ultraviolet (UV) radiation from the sunlight can harm skin cells, causing short-term effects, such as sunburns and long-term effects, such as pigmentation changes, changes in the skin's immune responses, and increased risk of skin cancer. These conditions can be largely prevented with proper sun protection measures and behavioural changes. This study aims to assess the knowledge on sun protection behaviour and baseline knowledge of medical students from the “Carol Davila” University of Medicine and Pharmacy, Bucharest, Romania. Methods: Data in this cross-sectional study were collected through a Google Forms questionnaire, which was distributed from November 2023 to December 2023 via digital communication channels to students across all academic years. STROBE guidelines were consulted for data synthesis; Results: A total of 668 stu-dents responded. The student cohort demonstrated a commendable level of awareness of the risks associated with sun exposure and the advantages of employing sun protection factor (SPF); how-ever, the incidence of sunburns remained notably elevated (72.3%). Further analysis revealed cor-relations among gender, academic year, presence of photosensitizing conditions, and adherence to SPF application. Additionally, there is a need to improve understanding of the appropriate appli-cation techniques for SPF, as only 11.5% of the students exhibited proficiency in this regard; Con-clusions: As future healthcare providers, medical students hold significance in promoting healthy behaviours in the broader community. This study indicates that while their knowledge about sun protection is satisfactory, there is scope for enhancement.

The composition and pattern of ecosystems are important factors determining the overall status and spatial differences of ecosystem service functions. However, under the background of differential land policies and ecological protection policies, research on the trend of ecological system pattern changes in the Fenhe River Basin is insufficient. Taking the upper and middle reaches of the Fenhe River Basin as the study area, based on long-term NDVI index and multi-period LUCC remote sensing images, this study used spatial statistics and time trend analysis methods to analyze the spatio-temporal dynamic changes of vegetation, land use, landscape pattern, and explored the impact of major driving factors on ecosystem changes. The results show that: (1) From 2010 to 2020, the vegetation cover in the upper and middle reaches of the Fenhe River Basin increased, with an annual NDVI increment of 0.003 (P<0.001). NDVI showed an increasing trend spatially, with significant statistics (P<0.001) and significant changes (P<0.05) in vegetation in high-altitude mountain areas, and the vegetation cover was mostly forests or grasslands. There was no significant change in vegetation cover in the low-lying urban agglomeration area. (2) From 2010 to 2020, the area of water bodies or wetlands in the study area significantly decreased, with 51.3% converted to arable land and 33.9% transferred to construction land, while only 2.2% remained as water bodies or wetlands. From 2015 to 2020, the trend of water body changes slowed down, with the proportions of conversion to arable land and construction land being 44.0% and 18.4% respectively, while the area of wetlands or water bodies remained at 16.3%. During the period of 2015-2020, the area of water bodies or wetlands converted to other land types increased by more than 14% compared to 2010-2015. This proportion reached more than 30% compared to the 13th Five-year Plan Period. (3) From 2010 to 2020, the spatial changes of landscape diversity (SHDI) and evenness (SHEI) of LUCC showed heterogeneous characteristics. In the high-altitude areas near the river basin boundary, the values of SHDI and SHEI were below 1.0. While in the low-altitude plain areas and urban areas with relatively frequent human activities, the values of SHDI and SHEI were above 1.0, and the values in urban areas could reach above 1.5. The evolution of ecosystem patterns in the upper and middle reaches of the Fenhe River Basin in the past decade has been clarified, providing a scientific basis for the construction and management of ecological environment governance and restoration projects in the Fenhe River Basin, and providing practical references for ecological protection and high-quality development practice in the Yellow River Basin.

Solanum nigrum fruits have been conventionally available as a material of beverage due to its nutritional substances such as minerals, vitamins, amino acids, proteins, sugars, polyphenols and anthocyanins. Here has rarely reported on the characterizaton of the components and the regulatory mechanism of Anthocyanins in S. nigrum. In this study, we determined that the peel and flesh of S. nigrum fruits shared the similar HPLC profiles, but the different contents and total antioxidant activities for Anthocyanins. After an efficient purification method mainly including extraction with pH 1.0 distilled water and then desorption with pH 1.0 95% ethanol after a DM-130 resin adsorption step to obtain more pure anthocyanins extracts, the purity of anthocyanins extract from S. nigrum fruits reached to 56.1%. Moreover, eight anthocyanins from S. nigrum fruit were identified with HPLC-MS/MS for the first time. A typical R2R3-MYB transcription factor gene, SnMYB, was also cloned for the first time by RACE-PCR from S. nigrum. Moreover, the contents of anthocyanins was shown a good correlation (r = 0.93) with the expression levels of SnMYB during the fruits developmental stages. Most significantly, SnMYB successfully produced high anthocyanins contents (1.03 mg/g) when SnMYB was transiently expressed in tobacco leaves. Taken together, S. nigrum fruits are a promising resource for anthocyanins extraction and SnMYB is an activator that positively regulates anthocyanins biosynthesis in S. nigrum.

We present a class of efficient parametric closure models for 1D stochastic Burgers equations. Casting it as statistical learning of the flow map, we derive the parametric form by representing the unresolved high wavenumber Fourier modes as functionals of the resolved variables’ trajectory. The reduced models are nonlinear autoregression (NAR) time series models, with coefficients estimated from data by least squares. The NAR models can accurately reproduce the energy spectrum, the invariant densities, and the autocorrelations. Taking advantage of the simplicity of the NAR models, we investigate maximal and optimal space-time reduction. Reduction in space dimension is unlimited, and NAR models with two Fourier modes can perform well. The NAR model’s stability limits time reduction, with a maximal time step smaller than that of the K-mode Galerkin system. We report a potential criterion for optimal space-time reduction: the NAR models achieve minimal relative error in the energy spectrum at the time step where the K-mode Galerkin system’s mean CFL number agrees with the full model’s.

With forty years of developments, bio-macromolecule cryo-electron microscopy has met its revolution of resolution and is playing a very important role in structural biology study. According to different specimen states, cryo-electron microscopy (cryo-EM) involves three specific techniques, single particle analysis (SPA), electron tomography and sub-tomogram averaging, and electron diffraction. All these three techniques have not realized their full potentials of solving structures of bio-macromolecules and therefore need to be developed in the future. In this review, the current existing bottlenecks of cryo-EM SPA are discussed with theoretical analysis, which includes air-water interface during specimen cryo-vitrification, bio-macromolecular conformational heterogeneity, focus gradient within thick specimen, and electron radiation damage. Besides, potential solutions of these bottlenecks are proposed and discussed, which are worthy of further investigations in the future.

Expression of the breast cancer resistance protein (BCRP/ ABCG2) transporter is downregulated in placentas from women with preeclampsia (PE) and in an immunological rat model of PE, which closely resembles human PE. While many drugs are substrates of this important efflux transporter, the impact of BCRP downregulation on maternal and fetal drug exposure has not been investigated. Using the PE rat model, we performed a pharmacokinetic study with rosuvastatin (RSV), a BCRP substrate, to investigate this impact. PE was induced in rats during gestational days (GD) 13 to 16 with daily low-dose endotoxin. On GD18, RSV (3 mg/kg) was administrated intravenously, and rats were sacrificed at time intervals between 0.5-6 hours. Placental expression of Bcrp and Oatp2b1 significantly decreased in PE rats. A corresponding increase in RSV levels was seen in fetal tissues and amniotic fluid of the PE group (p&lt;0.05), while maternal plasma concentrations remained unchanged. An increase in Bcrp expression and decreased RSV concentration, was seen in the livers of PE dams. This suggests that PE-mediated transporter dysregulation leads to significant changes in the maternal and fetal RSV disposition. Overall, our findings demonstrate that altered placental expression of transporters in PE can increase fetal accumulation of their substrates.

In the realm of artificial intelligence, knowledge graphs have become a fascinating area of research. Relationships between entities are depicted through a structural framework in knowledge graphs. In this paper, we propose to build a domain-specific medicine dictionary (DSMD) based on the principles of knowledge graphs. Our dictionary is composed of structured triples, where each entity is defined as a concept, and these concepts are interconnected through relationships. This comprehensive dictionary boasts more than 348,000 triples, encompassing over 20,000 medicine brands and 1,500 generic medicines. It offers a groundbreaking approach to storing and accessing medical data. Our dictionary facilitates various functionalities, including medicine brand information extraction, brand-specific queries, as well as queries involving two words or question answering. We anticipate that our dictionary will serve a broad spectrum of users, catering to both human users, such as diverse range of healthcare professionals as well as AI applications.

Information encryption and anti-counterfeiting play an important role in many aspects of daily life, such as in minimizing economic losses, protecting secure communication and public security, and so on. Owing to the high information capacity and ease of operation, luminescent materials for advanced information encryption and anti-counterfeiting are essential to meet the increasing demand on encryption security. Herein, we summarize two emerging luminescent materials for information encryption and anti-counterfeiting, the AIE materials and room-temperature phosphorescent materials. At last, we discuss the opportunities and anticipations of these two information encryption and anti-counterfeiting materials.

Valles Marineris (VM), the most prominent example of a Martian Valley Network, has been extensively studied for over 50 years, yet no detailed examination of the principal azimuths of the system exists. To address this, two methods are presented to precisely calculate the principal azimuths, a Bezier Spline analysis, and a GIS technique. The medial axis of the main canyon of VM was determined analytically from cubic polynomial splines fitted to 93 coordinate points along both north and south edges of the canyon. These splines were optimized, and medial axis points were calculated through numerical techniques that ensured orthogonality between the tangents of each spline and their connecting normal lines. 1,000 Medial Axis points were extracted, and various regression models constructed, including fitting to sinusoidal and cubic polynomial curves, achieving accuracies with R² values of 0.98 and 0.99, respectively. Principal azimuths were obtained using the sinusoidal equation with the slope of the tangent at any point x simply determined by the derivative of the curve’s equation. This analytic approach was cross-validated by a GIS method (using QGIS software), where a vector medial axis was obtained which produced principal azimuths that agreed with values from the analytic study with a correlation coefficient of 1.00, and a p value of 6.43e-65. The findings suggest that a deterministic process plays a significant role in the structural geometry of VM, highlighting its potential importance in the canyon’s formation.

Wearable exoskeleton solutions for upper limb rehabilitation or assistance, particularly for the hand area, have become increasingly attractive to researchers, proving to be effective over time in treating hand movement impairments following various neurological diseases. In the present work, the development of a wearable exoskeleton-type device for active hand rehabilitation has been addressed, based on fluid actuators made of elastomeric material and on myoelectric control by capturing myoelectric signals from the forearm area. The flexion movement of the fingers (phalanges) is actively assisted by pneumatic actuation of the built-in actuators and the extension movement is assisted by a depressurization control of the actuator. The device has been designed to be as easy to use as possible, light in weight, and to provide a high degree of comfort when used by the patient for rehabilitation training or daily life activities (ADL), which can be performed in the comfort of one's own home.

The threat of fine particulate matter concentration (PM2.5) is increasing globally, Tackling this issue requires an accurate understanding of its trends and drivers. The article investigates the PM2.5 characteristics of 285 prefecture-level cities in China from 2000-2018 based on multiscale geographically weighted regression(MGWR), and the results show that（1）previous studies based on classical MGWR models may be somewhat unstable, while MGWR can reflect the scale of influence of different variables on the dependent variable, and its regression results are more reliable.（2）PM2.5 is very sensitive to carbon emission(CE) factors, and there is a high degree of spatial heterogeneity, and the influence scale of location is the smallest among all variables, close to the municipal scale.（3）In 2000, the constant term all, IS, OFT, CE, and LT positively affect PM2.5, while GDP (jurisdiction) and UR negatively affect PM2.5; in 2010, the constant term all, GDP (jurisdiction), IS, OFT and LT positively affect PM2.5, while UR and CE negatively affect PM2.5; in 2018 the constant term all, IS, OFT and CE factors positively affect PM2.5, and GDP (jurisdiction), UR and LT negatively affect PM2.5.

Monin-Obukhov similarity theory (MOST) overestimates wind shear in some atmospheric stable conditions, i.e. Richardson number $R_f<0.25$. The overestimated wind shear that leads to an under-predicted friction wind speed and a lower ambient turbulence intensity for a given hub-height reference wind speed and a given roughness length, could influence wake modeling of a wind turbine. This work investigates the side effects of the breakdown of MOST on wake modeling under stable conditions and makes some modifications to the flow similarity functions to eliminate these side effects. Based on a field measurement in a wind farm, we firstly show that MOST predicts a larger wind shear for the atmospheric stability parameter $\zeta>0.1$ and proposes new flow similarity functions without constraining $R_f$ to limit the overestimated wind shear by MOST. Next, different turbulence models based on MOST and a modified one based on the new similarity functions are investigated through numerical simulations. These turbulence models are combined with the actuator disk model (AD) and Reynolds-averaged Navier–Stokes equations (RANS) to model wind turbine wakes under stable conditions. As compared to measurements, numerical results show that turbulence models based on MOST result in larger wake deficits and slower wake recovery rate with a square root of the mean-squared-error (RSME) of wake deficit in the range of 0.07-0.18. This overestimated wake effect is improved by applying the new similarity functions and the RSME of wake deficit is averagely reduced by 0.05. Finally, we check the role of the under-predicted turbulence intensity playing in the larger wake deficit predicted by models based MOST. Additional numerical simulations using the modified turbulence model are carried out, in which the roughness length is reduced to impose a hub-height ambient turbulence intensity equivalent to the MOST case. Simulation results show that reducing turbulence intensity enhances wake effects, however, it cannot reproduce the large wake deficit predicted by models based on MOST, which suggests that the overestimated wake effect by MOST could be also related to the overestimated wind shear.

Under the dual background of underemployment and health inequality, this paper empirically analyzes the impact of education level on underemployed workers’ health based on CLDS2016 data. The results show that underemployment is significantly related to the decline of self-rated health, increased depression tendency, and morbidity in a certain period. The results indicate that underemployment can significantly reduce the health level of workers in the low education level group and the high education level group. However, it has no significant impact on workers’ health in the middle education level group; even if we change the measurement method of indicators and consider endogeneity, the research conclusion is still robust. Moreover, this kind of health inequality mainly comes from the difference in economic effect and leisure effect of underemployment to workers with different educational levels. This paper provides empirical support for increasing the labor protection mechanism of underemployed people and reducing the health inequality caused by educational level differences.

Fully mechanized mining face production involves complex geological conditions; mining pressure; gas, water, fire and other mining environments. The working face needs a shearer, hydraulic support, a scraper conveyor and other equipment for coordination. The deep integration of intelligent technology with factors such as "humans, machines, the environment, and management" in the workplace is the core content of intelligent coal mines. This paper puts forward an advanced framework for coal mining robot technology systems, including single robots, robotized equipment, robot clusters and unmanned systems. The framework clarifies the common key technologies of coal mining robot research and development and cross-integration with new technologies such as 5G, the industrial internet, big data, artificial intelligence, and digital twins to improve the autonomous and intelligent application of coal mining robots. By establishing a scientific and complete standard system for coal mining robots, we aim to achieve customized research and development and standardized production of various types of robots. A specific analysis was conducted on the research progress of common key technologies such as explosion-proof design, mechanical system innovation, power drive, intelligent sensing, positioning and navigation, and underground communication of coal mining robots. The current research and application status of various types of coal mining robots in China are summarized. A new direction for future coal mine robot research and development is proposed. Moreover, robotic mining systems should be promoted to enhance the overall intelligence level and mining efficiency of mining equipment. To develop human‒machine environment-integrated robots to improve the autonomy and collaboration level of coal mining robots. The digital twinning of the entire mine robot system should be accelerated, the normalized operation level of coal mine robots should be improved, research on coal mining robots, support robots, and transportation robots should be carried out, intelligence should be achieved in fully mechanized mining faces, and equipment support for fewer and unmanned fully mechanized mining faces should be provided. The practical process of implementing coal mining robotization has been summarized, and the technical and engineering feasibility of the coal mining machine population has been verified.

To assure the opacity, an optimal problem is to retain the occurring events sequences as many as possible. Contrary to such problem, the other optimal problem is to preserve the minimal occurring events sequences. In the paper, based on the choosing cost, an optimal opacity-enforcing model is presented to minimize the sum of discount choosing cost, which is not only to preserve the opacity, but also to retain the secret to the maximum. To solve the model, two scenarios on opacity are considered. For the two scenarios, some algorithms are presented to achieve the optimal solution for the model by using the method of dynamic programming. And then, the solutions produced by the algorithms are proved correctly by theoretical proof. Finally, some illustrations for the algorithms are given.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Incident rates of neurodegenerative diseases have steadily increased globally, but there is no therapeutic access available. We newly prescribed medicinal herbal remedy including five different herbal plants called, Chen-Ma-Dan-Sam-Ga-Mi-Bang (CMST), purposed to prove for pharmacological properties and corresponded actions on hippocampus neuronal cell injury by hypoxia-induced mice model. Mice were adapted to normoxia or hypoxia with or without CMST for 5 days. We gathered pharmacological effects of CMST on cell injury by enhancement of dihydroethidium and 4-hydroxynonenal signals which were correlated with abnormal redox status in the protein or gene expression levels (abnormal elevations of nitric oxide, reactive oxygen species, lipid peroxidation and deteriorations of total glutathione, total antioxidant capacity, and activities of superoxide dismutase and catalase) due to hypoxia. CMST also notably exerted to attenuates molecules for neuronal cell injury markers such as p-tau, cleaved caspase-3 due to DNA oxidations (53bp1and phosphor-histone H2AX), inflammatory cytokines, and hemeoxigenase-1. We further figured out the underlying actions of CMST by in vitro experiment through inactivation of microglial cell which can mediate neuronal cell injury. Collectively, CMST prevented from hippocampal neuronal cells via inactivation of microglial cell with normalization of redox status on hypoxia-induced hippocampus neuronal cell injury.

This work presents the mathematical framework of the Second-Order Comprehensive Adjoint Sensitivity Analysis Methodology for Response-Coupled Forward/Adjoint Linear Systems (abbreviated as “2nd-CASAM-L”), which enables the most efficient computation of exactly obtained mathematical expressions of first- and second-order sensitivities of a generic system response with respect to functions (“features”) of model parameters. Subsequently, the first- and second-order sensitivities with respect to the model’s uncertain parameters, boundaries, and internal interfaces are obtained analytically and exactly, without needing large-scale computations. Within the 2nd-FASAM-L methodology, the number of large-scale computations is proportional to the number of model features (defined as functions of model parameters), as opposed to being proportional to the number of model parameters, which are considerably more than the number of features, being incomparably more efficient and more accurate than any other methods (statistical, finite differences, etc.) for computing exact expressions of response sensitivities (of any order) with respect to the model’s features and/or primary uncertain parameters, boundaries, and internal interfaces. The application of the 2nd-CASAM-L methodology is illustrated using a simplified energy-dependent neutron transport model of fundamental significance in nuclear reactor physics.

Work on callings has burgeoned in the past 20 years, yet recent reviews exposed a lack of conceptual clarity and disagreements around its definition, components and measures. One lingering point of contention revolves around the element of prosociality: Is a calling orientation primarily motivated by self-interest, prosocially orientated, or a mix of both? This conceptual paper reviews and examines the pro-self and prosocial component of a calling outlook, by examining and comparing the ways in which they feature in different calling subtypes: Classic, neoclassic, and modern callings. Our analysis suggests that these subtypes vary in where they are located on a pro-self – prosocial continuum: Classic callings are located on the prosocial side of the axis, modern callings are located on pro-self side of the axis, and neoclassic callings can be situated in the middle of the con-tinuum, integrating self-orientated and other-orientated motivations. Our analysis further suggests that these calling subtypes draw on divergent value systems: Classic callings are propelled by self-transcendent values, modern callings are driven by self-actualization motivations, and neoclassic callings integrate both value systems. We therefore argue that the subjective experiences of pursuing a calling within each subtype pathway differ, alt-hough they may culminate in similar outcomes. The paper offers a novel framework for analyzing people’s calling that draws on their values.

Objective To observe the effect of roxadustat on blood pressure and micro-inflammatory response in patients with hemodialysis anemia, and to provide a viable technique for the treatment of hemodialysis anemia patients. Methods A total of 100 hemodialysis anemia patients admitted to the Nephrology Department of our hospital from July 2020 to July 2021 were enrolled and randomly divided into an observation group (roxadustat) and a control group (human recombinant erythropoietin (rhEPO). The clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure were recorded and compared. Results There was no significant difference in baseline data and serum indicators (P>0.05). The study group demonstrated superior performance to the control group in terms of clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure (all P<0.05). Conclusion Compared with rhEPO treatment, roxadustat exhibits a promising outcome in treating anemia and has slight impact on blood pressure of patients.

EGFR tyrosine kinase inhibitors (TKIs) are the preferred initial treatment for non-small cell lung cancer (NSCLC) patients harboring EGFR mutations. However, remission is transient, and no further effective treatment options are available for EGFR-TKI-advanced EGFR-mutant NSCLCs. Immunotherapy with immune checkpoint inhibitors (ICIs) induces sustained cancer remission in a subset of NSCLCs. However, ICI therapy exhibits limited activity in most EGFR-mutant NSCLCs. Mechanistically, the strong oncogenic EGFR signaling in EGFR-mutant NSCLCs contributes to the non-inflamed tumor immune microenvironment (TIME), characterized by a limited number of CD8+ T cell infiltration, a high number of regulatory CD4+ T cells and a high number of inactivated infiltrated T cells. Besides, EGFR-mutant NSCLC patients are generally non-smokers with low levels of PD-L1 expression and tumor mutation burden. However, current understanding only partially explains why a small population of EGFR-mutant NSCLCs durably respond to ICI therapy, resulting in many researchers actively working in this field. This review reviews the hope seen from pre-clinical studies and clinical trials which may be adopted to improve the outcome of ICI therapy in EGFR-mutant NSCLCs. Besides, the underlying mechanisms leading to the inferior clinical outcome of ICI therapy in EGFR-mutant NSCLCs are discussed.

In intermediary metabolism, enzymes are mainly for the specific provision of one small molecule from another, B from A, for its further use. But there are also decades of work relating to another evolved purpose, which is to prevent untoward effects of odd compounds of various origins, and of ordinary intermediates, whose improper concentrations may be avoided by hydrolases and other activities of metabolic correction.

Effective discharge, which represents the flow, or range of flows, that transport the most sediment over long term, was determined based on the mean daily flow discharge and mean daily suspended sediment discharge recorded between 1994 and 2014 at four gauging stations along the Trotuș River. This study proposes an efficient method for the estimation of effective discharge based on observed values of the suspended sediment load. By employing this method the suspended sediment load is no longer either under- or overestimated as in the cases when the assessment is based on sediment rating curves. The assessment on effective discharge was performed at two distinct levels: for the entire data series during the investigated time spans and, subsequently, for flows less than the bankfull discharge. The effectiveness curves of the suspended sediment transport characteristics revealed highly multimodal characteristics with many peaks, indicating ample ranges for the effective discharges. The main effective discharge corresponded to large flood events, which are typical for the upper end of the discharge range, whereas the secondary effective discharges corresponded to sub-bankfull flows, which are more frequent. The changes that occurred in the channel bed are reflected by the temporal variations in the effective discharge.

This work introduces the mathematical framework of the novel “First-Order Comprehensive Adjoint Sensitivity Analysis Methodology for Neural Ordinary Differential Equations (1st-CASAM-NODE)” which yields exact expressions for the first-order sensitivities of NODE decoder-responses to the NODE parameters, including encoder initial conditions, while enabling the most efficient computation of these sensitivities. The application of the 1st-CASAM-NODE is illustrated by using the Nordheim-Fuchs reactor dynamics/safety phenomenological model, which is representative of physical systems that would be modeled by NODE while admitting exact analytical solutions for all quantities of interest (hidden states, decoder outputs, sensitivities with respect to all parameters and initial conditions, etc.). This work also lays the foundation for the ongoing work on conceiving the “Second-Order Comprehensive Adjoint Sensitivity Analysis Methodology for Neural Ordinary Differential Equations (2nd-CASAM-NODE)” which aims at yielding exact expressions for the second-order sensitivities of NODE decoder-responses to the NODE parameters and initial conditions while enabling the most efficient computation of these sensitivities.

This study presents a modest attempt to interpret, formulate, and manipulate emotion of robots within the precepts of quantum mechanics. Our proposed framework encodes the emotion information as a superposition state whilst unitary operators are used to manipulate the transition of the emotion states which are recovered via appropriate quantum measurement operations. The framework described provides essential steps towards exploiting the potency of quantum mechanics in a quantum affective computing paradigm. Further, the emotions of multi-robots in a specified communication scenario are fused using quantum entanglement thereby reducing the number of qubits required to capture the emotion states of all the robots in the environment, and fewer quantum gates are needed to transform the emotion of all or part of the robots from one state to another. In addition to the mathematical rigours expected of the proposed framework, we present a few simulation-based demonstrations to illustrate its feasibility and effectiveness. This exposition is an important step in the transition of formulations of emotional intelligence to the quantum era.

This paper utilizes dynamic panel threshold technology to conduct a nonlinear test on the direct effect between environmental regulation and economic fluctuations and the effect of industrial structure upgrading by taking 35 industrial sectors in China from 2003 to 2016 . The research has found that there is an inverted "U" relationship between environmental regulation and economic fluctuations, with the enhancement of environmental regulations, the economic fluctuation increases first and then decreases. The cross-terms of environmental regulation and industrial structure rationalization or industrial structure upgrading are significantly negative, which indicates that the enhancement of environmental regulation is conducive to promoting industrial structure upgrading and reducing the economic fluctuations. While the rationalization factors of industrial structure and advanced industrial structure are significantly negative, indicating that both forms of industrial structure upgrading are conducive to reducing the economic fluctuations. Environmental regulation has technical innovation thresholds for industrial structure upgrading and economic fluctuations, but there are no human capital or FDI thresholds. In the rationalization model of industrial structure, there is a nonlinear "U" relationship between environmental regulation and economic fluctuations when the proportion of scientific research expenditure is more than 1.35%. With the enhancement of environmental regulation, the economic fluctuation reduces first and then increases, and the corresponding inflection point value is 2.398% of the environmental regulation level. At the same time, the environmental regulation can indirectly reduce economic fluctuations by pushing down the industrial structure upgrades. In the advanced model of industrial structure, there is a “U” relationship between environmental regulation and economic fluctuation when the proportion of scientific research expenditure is greater than 1.26%. With continuous enhancement of environmental regulation, the economic fluctuation reduces first and then increases. The corresponding inflection point value is 1.78% of the environmental regulation level, and environmental regulation can indirectly reduce economic fluctuations by promoting the industrial structure at the same time.

In South Sudan, three case-control studies found a positive association between Nodding Syn-drome (NS) and a Mansonella perstans infection. To investigate whether M. perstans could play the primary and sole causal role in the development of NS, we examined blood films of persons with and without epilepsy in rural villages affected by NS in Mahenge, Tanzania, to identify M. perstans infections. Study participants were also examined for onchocercal nodules and skin lesions and tested for the presence of anti-O. volvulus antibodies (Ov16 ELISA). One hundred and thirteen epilepsy cases and 132 controls were enrolled, with a mean age of 28.3 years (interquartile range 22 – 34 years); 125 (51%) were females. Of the persons with epilepsy, 43 (38.1%) met the probable NS criteria. M. perstans infection was absent in all participants, but Ov16 prevalence and oncho-cerciasis-associated skin manifestations were positively associated with epilepsy, including probable NS. Onchocercal nodules in the mothers of cases were also positively associated with epilepsy. In conclusion, in contrast with O. volvulus, M. perstans is likely not endemic in Mahenge and therefore cannot be a co-factor for NS in the area. Hence, this filaria cannot be the primary and sole causal factor in the development of NS.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

The Global Burden of Disease Study (GBD 2019 Diseases and Injuries Collaborators) found that diabetes significantly increases the overall burden of disease, leading to a 24.4% increase in disability-adjusted life years. Persistently high glucose levels in diabetes can cause structural and functional changes in proteins throughout the body, and the accumulation of protein aggregates in the brain is associated with the progression of Alzheimer's Disease (AD).To address this burden of type 2 diabetes mellitus (T2DM), a combined aerobic and resistance exercise program was developed based on the recommendations of the American College of Sports Medicine. The prospectively registered clinical trials (https://www.clinicaltrials.gov/ct2/show/NCT04626453, https://www.clinicaltrials.gov/ct2/show/NCT04812288) involved two groups: an Intervention group of older sedentary adults with T2DM and a Control group of healthy older adults who could be either active or sedentary. The completion rate for the 2-month exercise program was high, with participants completing on an average of 89.14% of the exercise sessions. This indicated that the program was practical, feasible, and well-tolerated, even during the COVID pandemic. It was also safe, requiring minimal equipment and no supervision. The exercise instructions were easy to understand, making them suitable for older adults with cognitive decline.The near-infrared spectroscopy (NIRS) based brain and muscle oxygenation study provided evidence on brain overactivation among older adults with T2DM, supporting the compensatory theory. It also demonstrated that the 2-month combined exercise intervention effectively reduced brain overactivation and contributed to improved cognitive function. Operational modal analysis showed an exercise-related effect on the very low-frequency hemodynamic oscillations cluster, which may be associated with better vascular muscle and/or perivascular neurogenic regulation. Furthermore, we personalized the exercise duration and interval based on muscle oxygenation during physical tasks, leading to improvements in muscle oxidative capacity within just two months. This finding has practical implications for physical therapists, as they can target muscle oxygenation changes during physical tests to prescribe appropriate exercise doses for enhancing physical performance.

Abstract—Low-frequency Fahræus–Lindqvist-driven (not blood pressure-driven) oscillations in the small vessels are crucial because oscillations in small vessels support nutrient supply. Understanding of this is critical in type 2 diabetes mellitus (T2DM) to develop therapeutic measures to prevent Alzheimer's Disease Related Dementias: vascular factors contribute to cerebrovascular disease as well as mild cognitive impairment and dementia, which are predicted to affect 152 million people by 2050 (Alzheimer's Disease International London, UK, 2019). In this clinical study, we performed functional near-infrared spectroscopy (fNIRS) of the forehead to investigate the effect of the Mini-Cog with three-item recall test on the prefrontal cortex (PFC) activation and the relative oscillatory power in the 0.01–0.02-Hz (Fahræus–Lindqvist effect) and 0.021–0.052 Hz (smooth muscle autonomic innervation) frequency bands in elderly (60 years and older) T2DM and age-matched controls. We found a significant (p<0.01) difference in the PFC activation between elderly subjects with T2DM and age-matched elderly controls. Moreover, power spectral density (PSD) analysis revealed a significantly lower relative power in 0.021–0.052 Hz (smooth muscle autonomic innervation) frequency band in elderly subjects with T2DM during the Mini-Cog three-item recall test. Furthermore, a drop in the oscillatory power in the 0.01–0.02-Hz frequency band during Mini-Cog three-item recall test was found more pronounced in the elderly subjects with T2DM. Therefore, our study highlighted portable brain imaging to capture cerebrovascular reactivity to cognitive load that may provide a biomarker of cerebrovascular dysfunction in T2DM.Clinical Relevance— Our study establishes forehead portable brain imaging for monitoring cerebrovascular function in T2DM under cognitive load.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

The article discusses early diagnosis and intervention for developmental delays in children, emphasizing the role of specialized services and personnel in supporting recovery and development. It presents findings from a pilot project initiated in Bucharest, aiming to assess the incidence of developmental delays in children aged 1-3 years in selected kindergartens, including ASD. The study involved children, parents, and specialists, utilizing systematic behavior observation (SBO) and semi-structured interviews. Results indicate that out of 613 evaluated children, 81 received specialized control recommendations, with 4 cases showing potential risk of ASD. Additionally, 8 children were diagnosed with autism. The incidence of autism in children aged 1-3 years was 1 in 51. Although exploratory, these findings suggest a model of good practice for future early diagnosis campaigns nationally. Conclusively, the study underscores the importance of early diagnosis and intervention for developmental delays, advocating for a responsive community and emphasizing the significance of national-level efforts to address these issues effectively.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Hyaluronic acid, in the form of a gel or viscoelastic colloidal solution, is currently used for viscosupplementation of joints affected by osteoarthritis, but its effectiveness is under debate in relation to newer alternatives. Based on meta-analytical arguments, the present article reinforces the opinion that there are still no decisive arguments for its complete replacement, but for its use adapted to the peculiarities of the disease manifestation and of the patients. A “broad” comparison is first made with almost all alternatives studied in the last decade, and then a meta-regression study is performed to compare and predict the effect size induced by viscosupplementation and platelet-rich plasma therapies. If they are computerized, the developed models can represent tools for clinicians in determining the appropriateness of the option or not for viscosupplementation, in a manner adapted to the pain felt by the patients, to their age, or to other clinical circumstances. The models were generated using the latest algorithms for meta-analysis and meta-regression implemented in the R language and assembled in different R packages. All primary data and necessary R scripts are provided in accordance with the philosophy of reproducible research. Finally, HA-based products, currently under circumspection, are still clinically useful.

This study presents the development of a number of finite element (FE) models of the pelvis using different continuum and structural modelling approaches. Four FE models were developed using different modelling approaches: continuum isotropic, continuum orthotropic, hybrid isotropic and hybrid orthotropic. The models were subjected to an iterative adaptation process based on the Mechanostat principle. Each model was adapted to a number of common daily living activities (walking, stair ascent, stair descent, sit-to-stand and stand-to-sit) by applying onto it joint and muscle loads derived using a musculoskeletal modelling framework. The resulting models, along with a structural model previously developed by the authors, were compared visually in terms of bone architecture, and their response to a single load case was compared to a continuum FE model derived from CT imaging data. The main findings of this study were that the continuum orthotropic model was the closest to the CT derived model in terms of load response albeit having less total bone volume, suggesting that the role of material directionality in influencing the maximum orthotropic Young's modulus should be included in continuum bone adaptation models. In addition, the hybrid models, where trabecular and cortical bone were distinguished, had similar outcomes, suggesting that the approach to modelling trabecular bone is less influential when the cortex is modelled separately.

The development of hybrid unmanned aerial underwater vehicles (HAUVs) compatible with the advantages of the aerial vehicles and the underwater vehicles is of great significance. This paper presents the first study on a new HAUV layout using four rotors to realize the medium crossing motion of a transverse slender body similar to the fuselage of a missile or a submarine, that is the hybrid aerial underwater quadrotor (HAUQ). Then a robust control strategy is proposed for the take-off HAUQ on the water in the presence of unknown disturbances and complex model dynamic uncertainties. As a semi-submersible HAUQ rises straightly from the water, the inside of the slender fuselage placed horizontally is filled with water. The center of the mass, the moment of inertia, and the arm of force of the HAUQ will change rapidly in the takeoff phase from the water since the rapid non-uniform change of mass caused by the passive fast drainage. It is difficult to establish a accurate mathematical model of the complex dynamic changes caused by the multi-media dynamics, the fast changing buoyancy, and the added mass crossing air–water surface. Therefore, an uncertain kinematic and dynamic model is established through the passive fast nonuniform change and the complex dynamics are considered as the unknown terms, and the external disturbances of gust and other factors are assumed as the bounded disturbance input. A robust design approach is introduced to deal with the fast time-varying mass disturbance based on the input-to-state stability (ISS) theorem. The complex dynamics are estimated using the basis function and the unknown weight parameters, and the adaptive laws are adopted for the on-line estimation of the unknown weight parameters. Consider the residual disturbance of the uncertain nonlinear system as a total disturbance term, a disturbance observer is introduced for disturbance observation. The numerical simulation shows the feasibility and robustness of the proposed algorithm.

The article presents a mathematical model to investigate the operability envelopes for subsea production tress (SPT) installation using drill pipe. The finite differential method was used to solve the established governing equations in which the ocean conditions were considered. Based on the evaluations of the ocean wave, ocean current, water depth, specification of drill pipe and SPT weight that might dominate the mechanical behaviors of the pipe, the operability envelopes with permissible ocean conditions for SPT installation were obtained. The results indicate that changes of depths in deep water and SPT weight have few effects on the operation conditions and it would be better to choose smaller pipe to obtain larger permissible ocean conditions during SPT installation.

Artificial intelligence (AI) systems are poised to become deeply integrated into society. If developed responsibly, AI has potential to benefit humanity immensely. However, it also poses a range of risks, including risks of catastrophic accidents. It is crucial that we develop oversight mechanisms that prevent harm. This article outlines a framework for evaluating and auditing AI to provide assurance of responsible development and deployment, focusing on catastrophic risks. We argue that responsible AI development requires comprehensive auditing that is proportional to AI systems’ capabilities and available affordances. This framework offers recommendations toward that goal and may be useful in the design of AI auditing and governance regimes.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

To solve the benefit allocation problem between the subjects of the supply chain of general contracting projects. The Cobb-Douglas function is applied to establish the benefit distribution model when the two cooperate in the supply chain system, analyze the optimal benefit situation of one-time cooperation between the two parties under two modes of egoistic decision and collectivistic decision as well as the benefit distribution problem of multiple cooperation, and conduct numerical simulation to calculate the functional relationship between each decision variable and the contribution degree of the general contractor under different effort cost coefficients. The results show that：In the case of one-time cooperation between general contractors and subcontractors, regardless of the decision mode, the degree of effort of both parties is positively related to their own contributions and negatively related to each other's contributions; the overall benefit of the supply chain system is positively proportional to the degree of contribution of the general contractor and inversely proportional to the share of benefit distribution of the subcontractor; in multiple cooperation, the equilibrium result of both parties achieving Pareto optimality at each stage is that both parties choose to cooperate.

Cadmium(Cd) is a highly toxic and cumulative environmental pollutant. Siderophores are heavy metal chelators with high tolerance to heavy metals such as Cd. Furthermore, ryegrass (Lolium perenne L.) has potential remediation capacity for soils contaminated by heavy metals. Consequently, using ryegrass alongside beneficial soil microorganisms that produce siderophores may be an effective means to remediate soils contaminated with Cd. In this study, Bacillus strains WL1210 and CD303 that were previously isolated from the rhizospheres of Nitraria tangutorum in Wulan and Peganum harmala L in Dachaidan, respectively, both arid sandy environments, were evaluated for heavy metal pollution mitigation. The results indicate that both strains of Bacillus exhibit favorable biological characteristics and stress resistance, and they are both producers of siderophores, which promote the growth of ryegrass under Cd stress.

Atmospheric stability affects wind turbine wakes significantly. High-fidelity approaches such as large eddy simulations (LES) with the actuator line (AL) model which predicts detailed wake structures, fail to be applied in wind farm engineering applications due to its expensive cost. In order to make wind farm simulations computationally affordable, this paper proposes a new actuator disk model (AD) based on the blade element method (BEM) and combined with Reynolds-averaged Navier–Stokes equations (RANS) to model turbine wakes under different atmospheric stability conditions. In the proposed model, the upstream reference velocity is firstly estimated from the disk averaged velocity based on the one-dimensional momentum theory, and then is used to evaluate the rotor speed to calculate blade element forces. Flow similarity functions based on field measurement are applied to limit wind shear under strongly stable conditions, and turbulence source terms are added to take the buoyant-driven effects into consideration. Results from the new AD model are compared with field measurements and results from the AD model based on the thrust coefficient, the BEM-AD model with classical similarity functions and a high-fidelity LES approach. The results show that the proposed method is better in simulating wakes under various atmospheric stability conditions than the other AD models and has a similar performance to the high-fidelity LES approach however in much lower computational cost.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

Reticulate evolution through the interchanging of genetic components across organisms can impact significantly on the fitness and adaptation of species. Bread wheat (Triticum aestivum subsp. aestivum) is one of the most important crops in the world. Allopolyploid speciation, frequent hybridization, extensive introgression, and occasional horizontal gene transfer (HGT) have been shaping a typical paradigm of reticulate evolution in bread wheat and its wild relatives, which is likely to have a substantial influence on phenotypic traits and environmental adaptability of bread wheat. In this review, we outlined the evolutionary history of bread wheat and its wild relatives with a highlight on the interspecific hybridization events, demonstrating the reticulate relationship between species/subspecies in the genera Triticum and Aegilops. Furthermore, we discussed the genetic mechanisms and evolutionary significance underlying the introgression of bread wheat and its wild relatives. An in-depth understanding of the evolutionary process of Triticum species should be beneficial to future genetic study and breeding of bread wheat.

To promote of the rural revitalization strategy in China, this study attempts to summarize the gains and losses by the review of the design practice of rural buildings of the People's Commune in the late 1950s. Firstly, from the macro perspective, this paper gleans the relevant commune housing design cases in the Architectural Journal from 1958 to 1960 and summarizes the overall common design policies. Secondly, from the micro perspective, the paper analyzes the process of the investigation and creation through a concrete case. The paper concludes that the actual production and living needs of farmers must be taken into consideration in the process of the implementation of rural modernization, instead of simply putting the focus on standardized construction. Finally, the article points out the two characteristics of "rural modernity" reflected in the process of promoting rural modernization during the early stage of modern China: 1) collective wisdom and efforts; 2) combining local and foreign cultures. This article aims to provide a historical reference for current architects to carry out effective design practices in combination with rural development.

Dryland winter wheat in Loess Plateau is facing yield reduction due to shortage of soil moisture and delayed sowing time. Field experiment was conducted at Loess Plateau in Shanxi Province, China from 2012 to 2014, to study the effect of subsoiling and conventional tillage and different sowing dates on the soil water storage and contribution of N accumulation and remobilization to yield of winter wheat. The results showed that subsoiling significantly improved the soil water storage at 0-300 cm depth, improved the number of tillers and pre-anthesis N translocation in various organs of wheat and post-anthesis N accumulation, eventually increased the yield up to 17-36%. Delaying sowing time had reduced the soil water storage at sowing and winter accumulated temperature by about 180˚C. The contribution of N translocation to grain yield was maximum in glume+spike followed by in leaves and minimum by stem+sheath. In addition a close relationship was found between the N accumulation and translocation and the soil moisture in the 20-300 cm. Subsoiling during the fallow period and the medium sowing date was beneficial for improving the soil water storage and increased the N translocation to grain, thereby increasing the yield of wheat, especially in dry year.

This work presents a new scheme for autonomous control and obstacle detection of a catamaran unmanned surface vessel. Based on the Newtonian mechanics, hydrodynamics, and maneuvering modelling group modelling principles in the attached coordinate system, a three-degree-of-freedom motion model of the catamaran unmanned surface vessel is constructed. The fuzzy inference method is used to overcome the drawback that the traditional PID control cannot tune the PID parameters online, and the trajectory controller is designed. Meanwhile, 3D LIDAR is used to achieve obstacle detection. The results of the trajectory tracking simulations and experiments verify the accuracy of the model design and the effectiveness of the autonomous control design.

This paper examines the use of business maturity models as a tool for achieving business maturity and improving organizational performance in a rapidly changing business environment. Specifi-cally, the paper evaluates existing maturity models and methodologies, analyzes their effective-ness, and develops a novel and enhanced model tailored to the oil and gas sector. The authors highlight the importance of considering fundamental factors that underlie the implementation of maturity models and the need to evaluate their fit with organizational goals and values. The pa-per concludes by emphasizing the ongoing nature of business maturity and the effectiveness of theproposed Business Maturity Framework (BMF) model in enhancing operational excellence, competitiveness, and sustainable growth in the oil and gas industry. The paper makes a notable contribution to the specialized literature precisely through the differ-ent approaches to the business maturity process and through the proposed business maturity model itself as a base of strategy formulation, which includes a new dimension. This dimension analyzes whether the market and customers are ready for the level of digitization that the com-pany wants to achieve in a future state.

B lymphocyte development has two DNA recombination processes: V(D)J recombination of the immunoglobulin (Igh) gene variable region and class switching of the Igh constant regions from IgM to IgG, IgA, or IgE. V(D)J recombination is required for successful maturation of B cells from pro-B to pre-B to immature-B and then to mature B cells in the bone marrow. CSR occurs outside of the bone marrow when mature B cells migrate to peripheral lymphoid organs, such as spleen and lymph nodes. Both V(D)J recombination and CSR depend on an “open chromatin” state that makes DNA accessible to specific enzymes, recombination activating gene (RAG), and activation-induced cytidine deaminase (AID). Acetyltransferases GCN5 and PCAF possess redundant functions acetylating histone H3 lysine 9 (H3K9). Here, we generated a mouse model that lacks both GCN5 and PCAF in B cells. We found that double-deficient mice possess low levels of mature B cells in the bone marrow and peripheral organs, an accumulation of pro-B cells in bone marrow, and reduced CSR levels. We conclude that both GCN5 and PCAF are required for B cell development in vivo.

In the paper, a fully discrete compact difference scheme with $O(\tau^{2}+h^{4})$ precision is established by considering the numerical approximation of the one-dimensional Allen-Cahn equation. The numerical solutions satisfy discrete maximum principle under reasonable step ratio and time step constraint is proved. And the energy stability for the fully discrete scheme is investigated. An example is finally presented to show the effectiveness of scheme.

This work continues the review and illustrative application to energy systems of the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” (4th-BERRU-PM) methodology. The 4th-BERRU-PM methodology uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, in-cluding fourth (and higher) order sensitivities of computed model responses with respect to model parameters. The 4th-BERRU-PM methodology yields the fourth-order MaxEnt posterior distribution of experimentally measured and computed model responses and parameters, in the combined phase-space of model responses and parameters. The 4th-BERRU-PM methodology encompasses fourth-order sensitivity analysis (SA) and uncertainty quantification (UQ), which were reviewed in the accompanying work (Part 1), as well as fourth-order data assimilation (DA) and model calibration (MC) capabilities, which will be reviewed and illustrated in this work (Part 2). The applicability of the 4th-BERRU-PM methodology to energy systems is illustrated by using the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark, which is modeled using the linear neutron transport Boltzmann equation, involving 21976 im-precisely known parameters. This benchmark is representative of “large-scale computations” such as those involved in the modeling of energy systems. The result (“response”) of interest for the PERP benchmark is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. The impact of the high-order sensitivities of the response with respect to the PERP model parameters is quantified for “high-precision” parameters (2% standard deviations) and “medium-precision” parameters (5% standard deviations). Analyzing the best-estimate results with reduced uncertainties for the 1st- through 4th-order moments (mean values, covariance, skewness, and kurtosis) produced by the 4th-BERRU-PM methodology for the PERP benchmark indicates that, even for systems mod-eled by linear equations (e.g., the PERP benchmark), retaining only first-order sensitivities is insufficient for reliable predictive modeling (including SA, UQ, DA, MC). At least second-order sensitivities should be retained in order to obtain reliable predictions.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

Fluorescence microscopic images of cells contain a large number of morphological features that are used as an unbiased source of quantitative information about cell status, through which researchers can extract quantitative information about cells and study the biological phenomena of cells through statistical and analytical analysis. As an important research object of phenotypic analysis, images have a great influence on the research results. Saturation artifacts present in the image result in a loss of grayscale information that does not reveal the true value of fluorescence intensity. From the perspective of data post-processing, we propose a two-stage cell image recovery model based on generative adversarial network to solve the problem of phenotypic feature loss caused by saturation artifacts. The model is capable of restoring large areas of missing phenotypic features. In the experiment, we adopt the strategy of progressive restore to improve the robustness of the training effect, and add the contextual attention structure to enhance the stability of the restore effect. We hope to use deep learning methods to mitigate the effects of saturation artifacts to reveal how chemical, genetic, and environmental factors affect cell state, providing an effective tool for studying the field of biological variability and improving image quality in analysis.

China is in the climbing phase of the "Inverted U" environmental Kuznets curve, from excessive environmental consumption to the development stage of governance and protection, and green innovation. It is the most complex period of environmental quality. Environmental and policy regulation are very important. Select panel data of 29 provinces of China (excluding Hong Kong, Macau, Taiwan, Hainan and Tibet) from 2008 to 2017, construct a nonlinear two-threshold regression model, empirically analyse the impact of environmental tax and government innovation subsidies to green processes innovation, and attempt to explore whether the implementation of these two policies at the same time can make enterprises more inclined to green process innovation and whether there is an optimal space for policy implementation. It is proposed that the synergy effect of environmental tax and government innovation subsidy policies on enterprise green process innovation should be fully utilized, and the enterprise green process innovation environment and incentive mechanism should be improved to promote the green transformation and sustainable development of enterprises.

MIGAL – Galilee Research Institute is a regional R&amp;D center in the northeast peripheral region of Israel. An internationally recognized applied research institute, MIGAL specializes in biotechnology and computational sciences, plant sciences, precision agriculture and environmental sciences, as well as food, nutrition and health. Most of MIGAL’s researchers serve as the core faculty at Tel Hai Academic College (TH). Despite the country’s small surface area, socioeconomic inequality in Israel is high by OECD standards, with wage differences between rich and poor regions reaching up to 400%. The aims of this study are to identify possible socioeconomic impacts of MIGAL–TH on the peripheral northeast’s development. We discuss the effects of academic research and institutions of higher education on mitigating differences between the center and periphery of the country. Data for MIGAL, TH and the northeastern peripheral region were collected from the yearly reports of the two institutions and the Israel Central Bureau of Statistics. MIGAL was found to serve as a link between research, academic teaching and socioeconomic development in the northeast periphery. Several variables related to this link and describing MIGAL–TH and northeastern periphery development were analyzed over time: MIGAL’s budget, total number of employees and number of employees with PhDs; number of TH graduate students; socioeconomic index (SEI) of the northeastern periphery and its position on the Israeli list of regional SEIs. The signs and significance levels of their trends indicate a potential socioeconomic impact of academic research and higher education on peripheral development in the northeast of the country. Research budgets and the creation of jobs for academics living in the region are just a few examples of this impact.

Tulou dwellings in Southeast China have captivated global interest due to their distinctive appearance, sustainable construction materials and technologies, and their defensive and collective housing functions. Despite several recognized as World Cultural Heritage sites, the vast majority of tulou buildings are undergoing irreversible decline and destruction, necessitating a comprehensive and systematic study. Taking 83 Tulou buildings in Raoping County, Chaozhou City, Guangdong Province as the research object, this study reconstructs the historical scenes and systematically reveals the emergence, popularity, and consolidation process of tulou dwellings as integrated defensive and residential buildings for ordinary people by conducting a comprehensive analysis of historical documents and local chronicles. Based on an extensive field investigation, the study systematically analyzes the geospatial distribution and the spatial characteristics of Raoping tulou and its residential unit. The results demonstrate the adaptability and flexibility of tulou dwellings, showcasing their developmental process and revealing the inclusive nature of these traditional residences, as well as the initiative of those who reside within them. The research findings contribute to a more dynamic, comprehensive, and authentic understanding of tulou and Chinese traditional residences, providing valuable references for the preservation and sustainable development of tulou architectural heritage.

Lipid nanoparticles (LNPs) are promising carriers for constructing drug delivery systems (DDSs) in disease treatments. Previous studies have suggested that lipid composition and biophysical properties of LNPs can significantly impact their interaction with cells and tissues, allowing for the development of suitable LNPs for precise drug delivery. Our previous study proposed the concept and facile preparation of reconstituted lipid nanoparticles (rLNPs), which not only have the advantages of traditional LNPs but also contain the lipids of mother cell/tissue. In this study, we have found that brain-derived rLNPs (B-rLNPs) can have much better accumulation to the ischemic area of the ischemic stroke (IS) model than liver-derived rLNPs (L-rLNPs). This homing effect hopefully makes rLNPs a useful tool for developing highly accessible devices with homologous targeting ability for precise drug delivery.

The best business relationships are built as relationships between people and organizations that work together to achieve common goals. In the current digital era, B2B collaboration relationships are essential for business success. The response time to customer requests can be a key factor in maintaining these relationships and obtaining a competitive advantage. The use of VBA automation for repetitive tasks can help speed up this process, but it is important that computer operators have medium knowledge about using VBA macros. This work deals with issues related to improving response times to requests received by email, using a macro program for repetitive tasks. The empirical study was conducted on an average of 50 daily emails for order confirmation, with an average writing time of 68 s per email, resulting in a potential reduction in working time for the operator of approximately 1 h/day, only for order confirmation. The results show a significant improvement in working time for computer operators, using VBA buttons for repetitive tasks.

Supervised machine learning (SML) is a powerful method for predicting a small number of well-defined output groups (e.g., potential buyers of a certain product) by taking as input a large number of known well-defined measurements (e.g., past purchases, income, ethnicity, gender, credit record, age, favorite color, favorite chewing gum). SML is predicated upon the existence of a training dataset in which the correspondence between the input and output is known to be true. SML has had enormous success in the world of commerce, and this success may have prompted a few scientists to employ it in the study of molecular and genome evolution. Here, we list the properties of SML that make it an unsuitable tool in certain evolutionary studies. In particular, we argue that SML cannot be used in an evolutionary exploratory context for the simple reason that training datasets that are known to be a priori true do not exist. As a case study, we use an SML study in which it was concluded that most human genomes evolve by positive selection through soft selective sweeps (Schrider and Kern 2017). We show that in the absence of legitimate training datasets, Schrider and Kern (2017) used (1) simulations that employ many manipulatable variables and (2) a system of cherry-picking data that would put to shame most modern evangelical exegeses of the Bible. These two factors, in addition to the lack of methodological detail and negative controls, lead us to conclude that all evolutionary inferences derived from so-called SML algorithms (e.g., S-HIC) should be taken with a huge shovel of salt.

In training a deep learning system to perform audio transcription, two practical problems may arise. Firstly, most datasets are weakly labelled, having only a list of events present in each recording without any temporal information for training. Secondly, deep neural networks need a very large amount of labelled training data to achieve good quality performance, yet in practice it is difficult to collect enough samples for most classes of interest. In this paper, we propose factorising the final task of audio transcription into multiple intermediate tasks in order to improve the training performance when dealing with this kind of low-resource datasets. We evaluate three data-efficient approaches of training a stacked convolutional and recurrent neural network for the intermediate tasks. Our results show that different methods of training have different advantages and disadvantages.

Aspartame is the methyl-ester of the aspartate-phenylalanine dipeptide. Over time it became a very popular artificial sweetener. However, since its approval by the main food safety agencies, several concerns have been raised related to neuropsychiatric effects and neurotoxicity, due to its ability to activate glutamate receptors, as well as carcinogenic risks by increased production of reactive oxygen species. Within this review we critically evaluated reports concerning the safety of aspartame. Some studies evidenced subtle mood and behavioral changes upon daily high-dose intake below the admitted limit. Epidemiology studies also evidenced associations between daily aspartame intake and higher predisposition for malignant diseases like non-Hodgkin lymphomas and multiple myelomas, particularly in males, but association by chance still could not be excluded. While the debate over the carcinogenic risk of aspartame is ongoing, it is clear that its use may pose some dangers in peculiar cases, such as patients with seizures or other neurological diseases; it should be totally forbidden for patients with phenylketonuria, and reduced doses or complete avoidance are advisable during pregnancy. It would be also highly desirable for every product containing aspartame to clearly indicate on the label the exact amount of the substance and some risk warnings.

The present paper proposes a fractal analysis of the Covid-19 dynamics in 45 European countries. We introduce a new idea of using the box-counting dimension of the epidemiologic curves as a means of classifying the Covid-19 pandemic in the countries taken into consideration. The classification can be a useful tool in deciding upon the quality and accuracy of the data available. We also investigated the reproduction rate, which proves to have significant fractal features, thus enabling another perspective on this epidemic characteristic. Moreover, we studied the correlation between two meteorological parameters: global radiation and daily mean temperature and two Covid-19 indicators: daily new cases and reproduction rate. The fractal dimension differences between the analysed time series graphs could represent a preliminary analysis criterion, increasing research efficiency. Daily global radiation was found to be stronger linked with Covid-19 new cases than air temperature (with a greater correlation coefficient -0.386, as compared with -0.318), and consequently it is recommended as the first-choice meteorological variable for prediction models.

Rice canopy height and density are directly usable crop phenotypic traits for the direct estimation of crop biomass. Therefore, it is crucial to rapidly and accurately estimate rice canopy phenotypic parameters. To achieve non-destructive detection and estimation of essential phenotypic parameters in rice, a platform based on LiDAR point cloud data for rice phenotypic parameter detection was established. Data collection of rice canopy layers was performed across multiple plots. The LiDAR-detected canopy top point clouds were selected using a method based on the highest percentile, and the rice canopy surface model was calculated. Canopy height estimation was the difference between ground elevation and percentile value. To determine the optimal percentile defining the rice canopy top, testing was conducted incrementally from 0.8 to 1 with an increment of 0.005. The optimal percentile value was found to be 0.975. The root mean square error (RMSE) between LiDAR-detected canopy height and manually measured canopy height was calculated. The prediction model based on canopy height (R2=0.941, RMSE=0.019) exhibited a strong correlation with actual canopy height. Linear regression analysis was conducted between gap fraction of different plots and manually detected average Leaf Area Index (LAI) of rice canopy. Prediction models for canopy LAI based on ground return counts (R2=0.24, RMSE=0.1) and ground return intensity (R2=0.28, RMSE=0.09) showed strong correlations but had lower correlation with rice canopy LAI. Regression analysis was performed between LiDAR-detected canopy height and manually measured rice canopy LAI. The results indicated that the prediction model based on canopy height (R2=0.77, RMSE=0.03) was more accurate.

(1) In recent ten years, with the fast development of digital and engineering manufacturing technology, additive manufacturing has already been more and more widely used in the field of dentistry, from the first personalized surgical guides to the latest personalized restoration crowns and root implants. (2) Especially, the bioprinting of teeth and tissue is of great potential to realize organ regeneration and finally improve the life quality. (3) In this review paper, we firstly presented the workflow of additive manufacturing technology. Then we summarized main applications and recent research progresses of additive manufacturing in dentistry. (4) Lastly, we sketched out some challenges and future directions of additive manufacturing technology in dentistry.

Bone growth plate abnormalities and skull shape defects are seen in hypophosphatasia, a heritable disorder in humans that occurs due to deficiency of Tissue Nonspecific Alkaline Phosphatase (TNAP, Alpl) enzyme activity. Abnormal development of the cranial base growth plates (synchondroses) and abnormal skull shapes have also been demonstrated in global TNAP-/- mice. To distinguish local vs. systemic effects of TNAP on skull development, we utilized P0-Cre to knockout TNAP only in cranial neural crest derived tissues using TNAP flox mice. Here we show that TNAP deficiency in cranial neural crest leads to leads to skull shape defects and deficient growth of the intersphenoid synchondrosis (ISS). ISS chondrocyte abnormalities included increased proliferation in resting and proliferative zones with decreased apoptosis in hypertrophic zones. ColX expression is increased, indicative of premature differentiation in the absence of TNAP. Sox9 expression is increased in both resting and prehypertrophic zones of mutant mice. Expression of PTHrP and IHH were also increased. Finally, cranial base organ culture revealed that inorganic phosphate (Pi) and pyrophosphate (PPi) have specific effects on cell signaling and phenotype changes in the ISS. Together, these results demonstrate that TNAP expression in growth plate chondrocytes is essential for normal development, and that the mechanism likely involves Sox9, PTHrP, IHH and PPi.

The groundbreaking Advanced Forest-Based Tagging Framework (AFTF) represents a paradigm shift in the domain of information extraction from medical texts. AFTF introduces a novel dual-binary tree structure that redefines how entity-relation triples are extracted. This innovative approach directly tackles the limitations of traditional linear and graph-based methods, effectively addressing challenges related to overlapping triples and computational efficiency. The AFTF model stands as a beacon of excellence, surpassing established baselines by significant margins in comprehensive evaluations on two pivotal medical datasets. Notably, AFTF achieves remarkable improvements in F1 scores, showcasing its prowess in accurate information extraction from complex medical narratives. Beyond its exceptional performance in the medical domain, AFTF exhibits remarkable versatility. This adaptability is vividly demonstrated through its robust performance across three diverse public datasets, further affirming its position as a versatile and reliable solution for information extraction tasks. This paper provides a comprehensive exposition of the AFTF architecture, shedding light on its innovative design principles and its efficient handling of intricate medical texts. AFTF represents a groundbreaking step forward in the realm of information extraction, promising enhanced accuracy, efficiency, and adaptability for a wide range of applications.

In this paper, we present a groundbreaking methodology in the realm of aspect-level sentiment analysis, which capitalizes on the advanced capabilities of graph-based neural networks. Our approach, distinguished as the Aspect Correlation Graph Network (ACGN), represents a significant departure from conventional models. These traditional models often analyze aspects in isolation, failing to capture the intricate web of sentiment relationships that may exist within a single sentence. ACGN, however, is designed to address this gap by employing a sophisticated bidirectional attention mechanism, integrated with positional encoding. This unique combination not only enhances the model's ability to focus on relevant parts of the sentence but also aids in constructing detailed, aspect-focused representations. These representations are particularly crucial for understanding the nuanced interplay of sentiments associated with different aspects. Central to our model's architecture is the incorporation of a graph convolutional network. This network serves as a pivotal component in mapping and analyzing the complex network of sentiment correlations that can exist among various aspects within sentences. Through this integration, ACGN is able to unearth and interpret the subtle and often overlooked sentiment dynamics that traditional models might miss. Our comprehensive evaluations of the Aspect Correlation Graph Network, conducted using the SemEval 2014 datasets, have yielded promising results. These findings demonstrate a clear and significant advancement over the capabilities of existing models. Particularly, the results underscore the critical importance and utility of recognizing and understanding the connections between sentiments of different aspects in text analysis. This insight opens new avenues in the field of sentiment analysis, suggesting a broader application potential of ACGN in various contexts where understanding nuanced sentiment relationships is key. Overall, our study not only introduces a novel approach in aspect-level sentiment analysis but also sets a new standard for future research in this area. By highlighting the integral role of inter-aspect sentiment connections, ACGN paves the way for more sophisticated and accurate sentiment analysis tools, capable of handling the complexities of natural language with greater finesse and precision.

Water pollution is the main cause of global ecological degradation and seriously affects people's water supply. In order to respond to the water environmental protection policy and provide management departments with a basis for refining water quality, this paper used the environmental Gini coefficient (EGC) method based on four indicators such as water environmental capacity, population, land area, and gross domestic production (GDP) to represent social factors, economic factors, and environmental factors, respectively. After the optimization, for COD, the EGC based on the land area was 0.30, EGC based on population was 0.21, EGC based on environment capacity was 0.02, and the EGC based on GDP was 0.45, and the sum of EGC was 0.962. From this result, we observed that the change in the Gini coefficient of each indicator was not very big. Hence, the most significant change in the Gini coefficient was that of GDP, with a higher rate than other criteria. Then, the COD, AND, and TP discharge allocation model was constructed to obtain the total allocated discharge permit in Lushui Basin. The results found that the total discharge permit allocation of COD, AN, and TP to the Lushui basin were 51483.304 tons/year, 843.119 tons/year, and 340.926 tons/year, respectively. Based on the GIS spatial analysis technology, the distribution of unfair factors that cause pollution inequity was investigated. Finally, the reduction measures were proposed to implement environmental supervision and strengthen water environment management strictly.

The novel coronavirus pneumonia epidemic is still raging around the world. Therefore, during the period of a global pandemic, maintaining the normal circulation of medicine and health fields is the key to fight against the epidemic. This paper based on relevant data such as the export volume of cross-border e-commerce in Hangzhou, China from 2015 to 2019, the article uses system dynamics modeling to explore the impact of overseas warehouse services on cross-border e-commerce export transactions. Studies have shown that the introduction of overseas warehouses has significantly improved customer satisfaction and improved the quality of cross-border logistics services, which has a positive impact on cross-border e-commerce export transactions. Through sensitivity analysis, it can be seen that under the same conditions, the efficiency of customs clearance has the greatest impact on overseas warehouse services. Therefore, when allocating various investments in overseas warehouses, you can favor the customs clearance process to enhance the competitiveness of the cross-border e-commerce market and provide a feasible experience for healthcare supplies export from cross-border e-commerce.

In response to the fire protection design challenges faced by the integrated station-city engineering under the new model of station-city fusion, such as large building volume, diverse traffic types, functional integration, spatial complexity, and inapplicable standards, this paper selects Chongqing East Station as a typical engineering case. The fire safety engineering methods and performance-based fire protection design ideas were used. The paper summarized the fire protection difficulties, such as multifunctional combination construction, large fire protection distance, large fire protection zoning area, long evacuation distance, and design of evacuation (quasi) safety zones. Combining with the actual situation of the engineering, this paper analyzed the basic technical measures taken to address these design challenges. By adopting the method of fire safety engineering, the safety of the design scheme is verified, which can provide a solution approach for the current fire protection design challenges in the integrated station-city engineering.

The microstructure evolution during the cold rolling and subsequent annealing of Alloy 800H was investigated. Two distinct rolling methods, unidirectional rolling and cross-rolling, were intro-duced. Results show that better ductility was observed in the unidirectional rolling than in cross-rolling, whilst a higher volume fraction of large deformed grains was observed in the cross-rolled plates than in the unidirectionally rolled plates. Recrystallization occurred faster in plates from unidirectional rolling than from cross-rolling.

In this essay, I revisit Neural Networks (NNs) through the lens of evolutionary dynamics. From the two most important features of NNs, I recover the two most general equations of evolutionary dynamics. These two equations may thus serve as a connection between NNs and a body of knowledge that has been built over multiple centuries and has found application across a vast range of disciplines. This connection may therefore also help explain why NNs with the two features in question are applicable across a much broader range of domains than initially envisioned.

This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Open bidding is widely used in Sinopec's material procurement due to its advantages of openness, transparency, and cost savings. However, there have been many complaints about collusive bidding in recent years. Collusive bidding will pose significant challenges to fair competition and increase project costs for material procurement. Therefore, there is an urgent need for an analysis model to identify and prevent the collusive bidding. In this paper, we propose a statistical model for identifying collusive bidding using the coefficient of variation cv, the ratio of high to low average quotation rP and the deviation rate of quotation δ as indicators, based on the statistics of the historical quotations for material A. Through a case study of the framework agreement bidding for material B, we identified the collusion behavior of bidders effectively, thereby verifying the applicability of this statistical model.

The Semantic-Enhanced Tree-LSTM (SeT-LSTM) network, a novel advancement in the realm of linguistic modeling, marks a significant step forward from traditional Tree-based Long Short Term Memory (LSTM) networks. By intricately weaving in the nuances of typed grammatical dependencies, SeT-LSTMs offer a more nuanced understanding of language semantics. Traditional models often overlook the semantic shift caused by variations in word or phrase roles, a gap this paper aims to fill by focusing on the types of grammatical connections, or typed dependencies, within sentences. Our proposed architecture, dubbed the Semantic Relationship-Guided LSTM (SRG-LSTM), leverages a control mechanism to model the interplay between sequence elements. Additionally, we present a novel Tree-LSTM variant, the Semantic Dependency Tree-LSTM (SDT-LSTM), which integrates dependency parse structures with dependency types for more robust sentence embedding. The SDT-LSTM demonstrates superior performance in Semantic Relatedness Scoring and Sentiment Analysis compared to its predecessors. Qualitatively, it shows resilience to changes in sentence voice and heightened sensitivity to nominal alterations, aligning well with human intuition. This research underlines the pivotal role of grammatical relationships in sentence understanding and paves the way for further exploration in this domain.

Fire safety is a critical concern in various industries necessitating the development of sustainable and effective fire-resistant materials. Sustainable fire-resistant polysaccharide-based composite aerogels are regarded as innovative solutions in fire safety applications, and as such, research in this field has increased consistently over the past few years. Despite the plethora of literature on this important subject, only a few studies have attempted to map the global research of sustainable fire-resistant polysaccharide-based composite aerogels to identify the geospatial collaborative network and trend of research. This study utilizes a scientometric review of global trends in sustainable fire-resistant polysaccharide-based composite aerogels research between 2003–2023 by VOSviewer and biblioshiny to analyze co-author, co-word, co-citation, clusters, and geospatial map. A total of 234 bibliographic records from the Scopus database were analyzed to generate the study's research power networks and geospatial map. The most significant contributions in sustainable fire-resistant polysaccharide-based composite aerogels comes from China, the United States, Australia, Canada, and India with records of 194, 20, 11, 9, and 8 respectively. The top five sources for articles in this area of research include ACS Applied Materials and Interfaces, Chemical Engineering Journal, Composite Engineering, ACS Sustainable Chemistry and Engineering, and Carbohydrate Polymers. The application of sustainable fire-resistant polysaccharide-based composite aerogels spans the engineering and construction fields. The versatility in the fabrication and customization allows for seamless integration into diverse applications. The article concludes by emphasizing the significance of sustainable fire-resistant polysaccharide-based composite aerogels as a promising advancement in fire safety technology, combining sustainability, fire resistance, versatility, and mechanical strength to address critical challenges in the field. This study provides readers with an extensive understanding of the salient research themes, trends, and patterns of sustainable fire-resistant polysaccharide-based composite aerogel research worldwide.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

Three new cembranoids (1–3) and a new casbanoid (4), along with three known analogues (5–7), have been isolated from the soft coral Sinularia nanolobata collected off Ximao Island. The structures including the absolute configurations of new compounds were established by extensive spectro-scopic data analysis, time-dependent density functional theory/electronic circular dichroism (TDDFT-ECD) calculations and the comparison with spectroscopic data of known compounds. In in vitro bioassay, compounds 1 and 5 exhibited moderate cytotoxic activities against human erythroleukemia (HEL) cells line with IC50 values of 37.1 and 42.4 uM, respectively.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

BACKGROUND: Qu-aroma is a critical quality indicator for medium-high temperature Daqu (MT-Daqu), significantly influencing the aroma profile of strong-aroma Baijiu (SAB). SAB is produced across various regions in China, each with unique environmental conditions and production techniques. These regional differences are likely to cause variations in the Qu-aroma of MT-Daqu. Despite this, comprehensive research on the variations in Qu-aroma across different regions has been lacking. This study aims to address this gap by utilizing Gas Chromatography-Olfactometry-Mass Spectrometry (GC-O-MS) and electronic nose (E-nose) technology, combined with sensory evaluation, to analyze the differences in Qu-aroma characteristics and volatile compound profiles of MT-Daqu from seven distinct production areas.RESULTS: Sensory analysis identified seven broad aroma categories and 25 specific aromas characterizing the Qu-aroma of MT-Daqu samples. Chen aroma and roasted aroma were notably more prevalent in MT-Daqu samples from Sichuan compared to those from other regions (P < 0.05), while the fermentation aroma was less prominent in Sichuan samples. In total, 123 volatile compounds were detected in MT-Daqu, with 46 classified as aroma-active compounds. Among these, 21 aroma-active compounds were identified as markers distinguishing Sichuan MT-Daqu from those produced in non-Sichuan regions, showing significant differences in their concentrations (P < 0.05). Additionally, six major aroma-active compounds-ethyl isovalerate, ethyl heptanoate, hexanal, 1-nonanal, (E)-2,4-decadienal, and 2,3-dimethyl-5-ethylpyrazine-were found to significantly contribute to the aroma differences between Sichuan and non-Sichuan MT-Daqu.CONCLUSION: This study delineates the distinct Qu-aroma characteristics of MT-Daqu from various SAB production areas and identifies the aroma-active compounds responsible for these differences. The insights gained from this research offer valuable guidance for optimizing flavor profiles in MT-Daqu production, potentially enhancing the overall quality and regional distinctiveness of the product.

Leucine-rich repeat receptor-like kinases (LRR-RLKs) have been reported to play important roles in plant growth, development and stress responses. However, no comprehensive analysis of this family has been performed in Gossypium, which are important economic crop and suffer various stresses in growth and development. Here we conducted a comprehensive analysis of LRR-RLK family in four Gossypium species (G. arboreum, G. barbadense, G. hirsutum and G. raimondii). A total of 1641 LRR-RLK genes were identified in the four Gossypium species involved in our study. Maximum-likelihood phylogenetic tree revealed that all the LRR-RLK genes were divided into 21 subgroups. Exon-intron organization structure of LRR-RLK genes kept relative conserved in subfamilies and between Arabidopsis and Gossypium. Subfamilies XI and XII were found dramatically expanded in Gossypium. Tandem duplication acted as an important mechanism in expansion of Gossypium LRR-RLK gene family. Function analysis suggested that plant hormone signaling and plant-pathogen interaction pathway were enriched in Gossypium LRR-RLK genes. Promoters analysis and expression profiles analysis revealed that Gossypium LRR-RLK genes were extensively regulated by TFs, phytohormone and various environmental stimuli, and play key roles in stress defense and diverse development processes. Our study provided valuable information for further function study of Gossypium LRR-RLK genes.

Fifteen new diterpenoids, namely xishaklyanes A-O (1-15), along with three known related ones (16-18), were isolated from the soft coral Klyxum molle collected from Xisha Islands, South China Sea. The stereochemistry of the new compounds were elucidated by a combination of detailed spectroscopic analyses, chemical syntheses, quantum chemical calculations and comparison with the reported data. The absolute configuration of compound 18 was established by the modified Mosher's method for the first time. In bioassay, some of these compounds exhibited considerable antibacterial activities on fish pathogenic bacteria, and compound 4 showed the most effective activity with MIC of 0.225 g/mL against Lactococcus garvieae.

It is documented that maternal diseases or treatments influence a newborn’s clinical status at birth; autoimmune diseases with circulating antibodies are often clinically expressed transiently in newborns due to the crossover of the specific IgG through the placenta during pregnancy. The offspring can inherit maternal genetic anomalies, but clinical expression usually becomes patent later in life. If prenatal medical history is not available or if signs or symptoms of a mother’s disease are revealed for the first time during pregnancy or postpartum, their effects on the newborn may be misattributed. In this article, we present three cases of pregnant women, without any known pathology before or during pregnancy, who gave birth to very sick preterm newborns that required admission to the Neonatal Intensive Care Unit (NICU). The neonates’ complications were considered initially as consequences of prematurity or infection, but later investigations revealed transient autoimmune disease in two of the cases (myasthenia gravis and hyperthyroidism) and a severe form of thrombophilia in the third case. In all cases, mothers were asymptomatic and unaware of their subclinical disease. Preemies’ diagnosis has contributed to the identification of their mothers’ pathology and adequate treatment was prescribed with favourable short- and long-term outcomes. In one of the cases (myasthenia gravis) both mother and child had associated infectious diseases in the perinatal period that complicated the clinical picture and created problems of diagnosis. This article intends to emphasize the paramount importance of prenatal care, for both mother and newborn. Repeated medical visits and investigations throughout the pregnancy are a good opportunity to detect subclinical diseases or predispositions. As newborns usually develop non-specific signs, one should have experience and pay attention to differentiate among etiologies. Our paper takes a reversed approach to the usual medical diagnosis pathway: from infant to mother instead of mother towards the infant, proving that inter-speciality collaboration can work bi-directionally.

Stemming from the object overlap and undertraining from the few samples, the road dense object detection is confronted with the poor object identification performance and the inability to recognize edge objects. Based on this, one transfer learning-based YOLOv3 approach for identifying dense objects in the road has been proposed. Firstly, Darknet-53 network structure is adopted to obtain pre-trained YOLOv3 model, then the transfer training is introduced as the output layer for the special dataset of 2000 images containing vehicles; in the proposed model, one random function is adapted to intialize and optimize the weights of the transfer training model, which is seperately designed from the pre-trained YOLOv3; and the object detection classifier replaces the fully connected layer, which further improves the detection effect, the reduced size of the network model can further reduce the training and detection time, and can be better applied to actual scenarios. The experimental results demonstrate that the object detection accuracy of the presented approach is 87.75% for the Pascal VOC 2007 dataset, which is superior to the traditional YOLOv3 and the traditional YOLOv2 by 3.05% and 11.15%, respectively. Besides, the test was carried out using UA-DETRAC, a public road vehicle detection dataset, the object detection accuracy of the presented approach reaches 79.23% in detecting images, which is 4.13% better than the traditional YOLOv3, and compared with the existing relatively new object detection algorithm YOLOv5, the detection accuracy is 1.36% better. Moreover, the detection speed of the proposed YOLOv3 method reaches 31.2 Fps/s in detecting images, which is 7.6 Fps/s faster than the traditional YOLOv3, and compared with the existing relatively new object detection algorithm YOLOv5, the speed is 4.3 Fps/s faster; the proposed YOLOv3 performs 79.38Bn of floating point operations per second in detecting video, which obviously surpasses the traditional YOLOv3 and the newer object detection algorithm YOLOv5.

One important motivation for the implementation of the Water Framework Directive is the creation of non-market environmental benefits such as improved ecological quality, or greater opportunities for open-access river recreation via microbial pollution remediation. Pollution sources impacting on ecological or recreational water quality can be uncorrelated but non-market benefits arising from riverine improvements are typically conflated within benefit valuation studies. Using stated preference choice experiments, we seek to disaggregate these sources of value for different river users, thereby allowing decision makers to understand the consequences of adopting alternative investment strategies. Our results suggest anglers derive greater value from improvements to the ecological quality of river water, in contrast to swimmers and rowers for whom greater value is gained from improvements to recreational quality. We also find three distinct groups of respondents: a majority preferring ecological over recreational improvements, a substantial minority holding opposing preference orderings and a small proportion expressing relatively low values for either form of river quality enhancement. As such, this research demonstrates that the non-market benefits which may accrue from different types of water quality improvements are nuanced in terms of their potential beneficiaries and, by inference, their overall value and policy implications.