The presence of high concentrations of flammable gases and volatile organic compounds in the atmosphere has been widely reported to be detrimental to human survival. A lot of research effort has been put towards finding an efficient means of quick detection of these gases below their ‘immediately dangerous to life or health’ concentrations. Detecting these gases in an oxygen-deficient environment is a crucial task to consider and has been overlooked. In this research, double substitution spinel with chemical formula Co1-2xNixMnxFe2-yCeyO4, where 0 ≤ x = y ≤ 0.3, were prepared via the glycol-thermal technique. The final products following the appropriate substitution are CoFe2O4 (dried naturally), CoFe2O4 (dried with Infrared lamp), Co0.8Ni0.1Mn0.1Fe1.9Ce0.1O4, Co0.6Ni0.2Mn0.2Fe1.8Ce0.2O4, and Co0.4Ni0.3Mn0.3Fe1.7Ce0.3O4 spinel ferrites. The X-ray diffractometry (XRD), High resolution transmission electron micrographs (HRTEM), and X-ray photoelectron spectroscopy (XPS) of the samples confirm the formation of the spinel. The gas sensing performance of this samples were tested at operating temperature of 225 ºC towards liquefied petroleum gas (LPG), ammonia, ethanol, and propanol. The Co0.8Ni0.1Mn0.1Fe1.9Ce0.1O4-based sensor was selective to LPG, with a high response of 116.43 toward 6 000 ppm of LPG when helium was used as carrier gas, 3.35 when dry-air was the carrier gas, 4.4 when nitrogen was the carrier gas, but was not sensitive when argon was used as a carrier gas.

Reducing under-five mortality is a key indicator of a country's overall development, yet in Angola, understanding the factors contributing to hospital deaths in this vulnerable demographic remains incomplete despite improvements in healthcare infrastructure and public health policies. With one of the highest under-five mortality rates in Sub-Saharan Africa, Angola grapples with significant challenges, including malaria, malnutrition, pneumonia, neonatal conditions, and intestinal infectious diseases, as leading causes of death among children. This study aimed to identify factors associated with these hospital deaths in children aged 28 days to five years admitted to DBPH in Luanda between May 2022 and June 2023. Utilizing a hospital-based case-control design, a total of 1020 children were studied, with 340 cases of hospital deaths. Notably, distal and intermediate determinants emerged as primary predictors of hospital mortality, revealing significant associations with maternal education status, maternal alcohol consumption during pregnancy, short hospital stays (≤24h), poor nutritional status, short interbirth intervals, maternal age ≤19 years, and maternal age ≥35 years. These findings underscore the preventable nature of most under-five hospital deaths and emphasize the urgent need to address social inequities and enhance the quality of primary healthcare services to effectively mitigate child mortality.

The type 6 protein secretion system (T6SS) is prevalently utilized by Gram-negative bacteria to compete for resources and space. Upon activation, toxic effectors from this secretion system are translocated into the competitor prokaryote or eukaryote in a contact-dependent manner. While much has been reported on T6SS-mediated prokaryotic competition, very little is understood about the mechanisms of bacterial interactions with eukaryotic hosts. Likewise, many virulent T6SS effectors are known to be antibacterial. In recent years, however, evidence has emerged on numerous T6SS effectors that interact with related immunity proteins in a range of eukaryotic hosts. Insights into how this effector-immunity pairing alters the physiological responses of the recipient organism might provide opportunities relating to the T6SS agricultural and biotherapeutic applications. We, therefore, summarize the impacts of the T6SS effectors with a special focus on bacterial interactions with animals, plants, and fungi. We further briefly discuss pipelines that are currently used to characterize antieukaryotic T6SS effectors.

Phytopathogenic oomycetes are known to infect a host plant successfully due to their ability to secrete a set of protein effectors. Of interest to many researchers are effectors with the N-terminal RxLR motif (Arginine-any amino acid-Leucine-Arginine). Owing to the genome sequencing, we can now comprehend the high level of diversity among oomycete effectors, and similarly, their conservation within and among species core RxLR effectors (CREs). Currently, there are a couple of putative CREs that have been identified in oomycetes. The functional characterization of these CREs proposes their virulence role with the potential of targeting central cellular processes that are conserved across diverse plant species. This could be harnessed in engineering plants for broad-spectrum and durable resistance.

Abstract: The promise of regenerative medicine and tissue engineering is founded on the ability to regenerate diseased or damaged tissues and organs into functional tissues and organs or the creation of new tissues and organs altogether. In theory, all damaged and diseased tissues and organs can be regenerated or created using different configurations and combinations of extracellular matrix, cells and inductive biomolecules. Currently, regenerative medicine and tissue engineering can allow the improvement of patients’ quality of life through availing novel treatment options. Tissues and organs have a specific ECM, with specific proteins and factors released by cells residing within the local microenvironment. The coupling of regenerative medicine and tissue engineering field with 3D printing is revolutionizing the treatment of patients in a huge way. 3D bioprinting allows the proper placement of cells and ECMs, allowing the recapitulation of native microenvironments of tissues and organs. 3D bioprinting utilizes different bioinks made up of different formulations of ECM/biomaterials, biomolecules and even cells. The choice of the bioink used during 3D bioprinting is very important as properties such as printability, compatibility and physical strength influence the final construct printed. The extracellular matrix (ECM) provides both physical and mechanical microenvironment needed by cells to survive and proliferate. Decellularized ECM bioink contains biochemical cues from the original native ECM and also the right proportions of ECM proteins. Different techniques and characterization methods are used to derive bioinks from several tissues and organs and to evaluate their quality. This review discusses the uses of decellularized ECM bioinks and argues that they represent the most biomimetic bioinks available. In addition, we briefly discuss some polymer-based bioinks utilized in 3D bioprinting.

A systematic and comprehensive review of critical applications of Blockchain Technol-ogy with Differential Privacy integration lies within the privacy and security enhancement. This paper aims to highlight the research issues in the e-health domain (e.g., Electronic Medical Rec-ords) and to review the current research directions in Differential Privacy integration with Blockchain Technology.(1) Background: The current state of the art in the e-health domain is identified as follows: (a) healthcare information poses a high level of security and privacy concerns due to its sensitivity; (b) due to vulnerabilities surrounding the healthcare system, a data breach is common and presents a risk for attacks by an adversary; and (c) the current privacy and security apparatus needs further fortification. (2) Methods: The methodology uses a systematic literature review (SLR) to identify and select relevant research papers and academic journals in DP and BT. (3) Results: The results are categorized into: e-Health Record Privacy, Real-Time Health Data, and Health Survey Data Protection to identify inherent issues with Differential Privacy integra-tion with Blockchain and technical challenges.(4) Conclusion: This review thoroughly surveyed and summarized Differential Privacy mechanisms in EMR privacy, real-time health data, and health survey data protection while highlighting challenges.

The two-parameter distribution introduced by Kumaraswamy (1980) is a very flexible alternative to the Beta distribution with the same (0,1) support. Originally proposed in the field of hydrology, it has subsequently received a good deal of positive attention in both the theoretical and applied statistics literatures. Interestingly, the problem of testing formally for the appropriateness of the Kumaraswamy distribution appears to have received little or no attention to date. To fill this gap, in this paper we apply the “biased transformation” methodology proposed by Raschke (2009) to several standard goodness-of-fit tests based on the empirical distribution function. A simulation study reveals that these (modified) tests perform well in the context of the Kumaraswamy distribution, in terms of both low size distortion, and respectable power. In particular, the “biased transformation” Anderson-Darling test dominates the other tests that are considered.

Modern imaging strategies are paramount to studying living systems such as cells, bacteria, and fungi and their response to pathogens, toxicants, and nanomaterials as modulated by exposure and environmental factors. The need to understand the processes and mechanisms of damage, healing and cell survivability of living systems continues to motivate the development of alternative imaging strategies. Of particular interest is the use of label-free techniques that minimize interference of biological processes by foreign marking substances and reduce intense light exposure and potential photo-toxicity effects. This review focus on the potential synergic capabilities of atomic force microscopy (AFM) as a well-developed and robust imaging strategy with demonstrated applications to unravel intimate details in biomedical applications, with the label-free, fast, and enduring Holotomographic Microscopy (HT) strategy. We first review the operating principles that form the basis for the complementary details provided by these techniques regarding the surface and internal information provided by HT and AFM is essential and complimentary for the development of several biomedical areas studying the interaction mechanisms of nanomaterials with living organisms. First, AFM can provide superb resolution on surface morphology and biomechanical characterization. Second, the quantitative phase capabilities of HT enable superb modeling and quantification of the volume, surface area, protein content, and mass density of the main components of cells and microorganisms, including morphology of cells in microbiological systems. These capabilities result from directly quantifying refractive index changes without requiring fluorescent markers or chemicals. As such, HT is ideally suited for long-term monitoring of living organisms in conditions close to their natural settings. We present a case-based review of the principal uses of both techniques and their essential contributions to nanomedicine and nanotoxicology, emphasizing cancer and infectious disease control. The synergic impact of the sequential use of these complementary strategies provides a clear drive for adopting these techniques as interdependent fundamental tools.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

The ability to self-direct a research program determines graduate degree completion. Yet, research on incompletion of graduate physics programs assume students’ present level of self-direction adequate and neglects to recognize a lack of self-directed learning as key. One theoretical mathematical physicist focused on changing this challenge of physics graduate education by promoting self-directed learning through the type research flow that has been found to bring the greatest satisfaction to researchers with respect to their insights. This he provided through his space, time, open mindedness and theoretical contributions with his students and in collaboration with his colleagues. A self-directed learner himself, David J. Rowe developed methods of mentoring for encouraging physics graduate students to recognize symmetry as valuable in identifying solutions to problems quickly—helping these students take the lead in finding insightful resolutions to complex, multidimensional, mathematical physics uncertainties. How Rowe set about supporting self-directed learning in his graduate physics education interactions will be examined with the use of narrative research to interpret the texts and conversations with the author he made available. His techniques will be presented and recommendations made regarding how Rowe’s work in this regard can be modeled to improve self-direction in STEM graduate education.

Aim: Streptococcus pneumoniae and influenza H1N1 virus are common organisms associated with human infections. These infections could play a significant role in immune regulation. The study was performed to analyse the genome sequences of these organisms with human genome and study its functional significance. Methods: The study was performed to analyse the overlapping of genome sequences in Streptococcus pneumoniae and Influenza (H1N1) virus against human genome sequences by BLASTn sequence analysis. The alignments are studied against the corresponding genes for their functional significance with DAVID and NDEx software.Results: Several hits or overlapping nucleotide segments were identified. Between streptococcus and homo sapiens 287 overlaps were identified, and among influenza and homo sapiens 124 hits were identified. A wide range of functional significance of these genes were identified, and the results are presented in this study. The results show insights into functional pathways and biological activities associated with the respective vaccinations or infections by these microorganisms. Conclusion: The common organisms like Streptococcus pneumoniae and Influenza H1N1 virus actively interact with the immune system and result in a wide range of immune regulations.

Zinc oxide (ZnO) has been widely studied over the last decade for its remarkable properties in optoelectronic and photovoltaic devices because of its high electron mobility and excitonic properties, probably the broadest range of nanostructured forms, and their ease and low cost of synthesis by a wide variety of methods. The volume of recent work on ZnO nanostructures and their devices can potentially overshadow significant developments in the field. Therefore, there is a need for a concise description of the most recent advances in the field. In this review, we focus on the effect of ZnO nanostructure morphologies on the performance of ZnO-based solar cells sensitized using methylammonium lead iodide perovskite. We present an exhaustive discussion of the synthesis routes for different ZnO nanostructure morphologies, ways to control the morphology, and the impact of morphology on the photo-conversion efficiency of a given PSC.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

The combination of statistical learning technologies with large databases of psychophysiological data has appropriately generated enthusiastic interest in future clinical applicability. It is argued here that this enthusiasm should be tempered with the understanding that significant obstacles must be overcome before the systematic introduction of psychophysiological measures into neuropsychiatric practice becomes possible. The nonspecificity of psychophysiological measures complicates their use in diagnosis. Low test-retest reliability complicates use in longitudinal assessment, and quantitative psychophysiological measures can normalize in response to placebo intervention. Ten cautionary observations are introduced and, in some instances, possible directions for remediation are suggested.

Purpose: The purpose of this study is to further explore how e-loyalty and E-marketing influences E-trust and satisfy the demand by offering fresh perspectives based on research as well as emphasis on the factors influencing the E-trust such as culture as a mediator. This study not only contributed theoretically but also presented practical implementations. Design/methodology/approach: Online survey was used to obtain data by focusing the Hospitality sector (Hotel Industry) and verifying the conceptual framework. Data was collected in multiple time lags. Findings: Findings showed that the E-trust influenced by E-loyalty and E-Marketing. E-trust comes from the previous experiences, e-loyalty and e-marketing. Further, some trends such as culture influenced the e-trust. Research limitation/implications: The present study is quite suitable for those Researchers interested in learning more about the effects of E-loyalty and E-marketing on user E-trust and how to mitigate cultural influences can benefit from the current study. This research also has implications for those who wish to improve market allure and survival in digital world. This study focused on the hospitality sector (Hotel Industry) in China; however, the sector and geography could be altered to suit the needs of the study's participants. Practical implications: The present study delivers the practical guidelines which are quiet suitable for understanding the formation of E-loyalty, E-marketing, and E-trust through which specific E-marketing strategy can be designed to deal with the consumer’s E-loyalty and their expectations as per their Cultural perspective. At some particular regions/countries, cultural trends are more important than practical market. This research study practically showed that how culture changed the consumer set of mind. Originality/value: The relationship between E-loyalty, E-marketing, E-trust, specifically with the cultural influence in digital market has been the subject of few research.

Current VAT rules for cross-border e-commerce companies in the EU are not sustainable, because they are extremely complex and often opaque, due to the lack of tax harmonization. The aim of the research is to explore, using a qualitative method, what kind of harmonization would make the current legislation more uniform, simpler, more transparent, and easier to understand, without conflicting with the rules of any Member State. To this end, the aspects of the new platform regulation introduced on 1 July 2021 and its potential for expansion are assessed through information from possible sales models. The research suggests that the rules on platforms do not cover all possible sales models, which in our view imposes an unnecessary extra administrative burden on some businesses and makes their tax activities less transparent. In the light of the results of the research, we propose that the current EU platform regulation should be extended to cover B2B, B2C transactions and services. As a result of this suggested harmonization, a simpler, more transparent, uniform and sustainable tax system would contribute to the whitening of the economy, generating additional tax revenue for Member States.

Late blight caused by the oomycete pathogen Phytophthora infestans is a devastating disease of potato and tomato worldwide, including Israel. The population structure of this pathogen was monitored in potato and tomato fields in Israel during a 36-year period of 1983-2019. Isolates of the pathogen were tested for sensitivity to phenylamide fungicides, mating type, race structure, and genotype. The phenotypic and genotypic structure of the population from potato have changed greatly from one year to another, from one season to the next, within a season and within a single field. Major changes also occurred in the population collected from tomato crops. The mechanisms driving these multiple changes and the heterogeneous nature of the population in Israel are shown to derive from multiple migration events of the pathogen via seed tubers from Europe and from fitness-driven selection processes.

Hepatitis E virus (HEV) is a common cause of acute hepatitis worldwide, accounting for approximately 25% of deaths among pregnant women. We previously reported that pregnancy serum facilitates HEV replication in vitro. However, the differences in host cells with HEV infection induced by pregnancy serum and fetal bovine serum (FBS) are unclear. In this study, differentially expressed proteins were identified in HEV-infected hepatoma cells (HepG2) supplemented with different sera by using isobaric tags for relative and absolute quantitation. Proteomic analysis indicated that HEV infection significantly induced 1014 differentially expressed proteins in HEV-infected HepG2 cells when supplemented with FBS compared with pregnancy serum. Further validation by Western blot confirmed that filamin A, heat-shock proteins 70 and 90, Cytochrome c, and Thioredoxin were associated with HEV infection. This comparative analysis provides an important basis to further investigate HEV pathogenesis in pregnant women and HEV replication.

Modules composed of a resistance gene flanked by Xer site-specific recombination sites, the vast majority of which were found in Acinetobacter baumannii, are thought to behave as elements that facilitate horizontal dissemination. The A. baumannii xerC and xerD genes were cloned, and the recombinant clones used to complement the cognate Escherichia coli mutants. The complemented strains supported resolution of plasmid dimers, and, as is the case with E. coli and Klebsiella pneumoniae plasmids, the activity was enhanced when cells were growing in low osmolarity growth medium. Binding experiments showed that partially purified A. baumannii XerC and XerD proteins (XerC_Ab and XerD_Ab) bound synthetic Xer site-specific recombination sites, some of them with a nucleotide sequence deduced from existing A. baumannii plasmids. Incubation with suicide substrates resulted in covalent attachment of DNA to a recombinase, probably XerC_Ab, indicating that the first step in the recombination reaction took place. The results described show that XerC_Ab and XerD_Ab are functional proteins and support the hypothesis that they participate in horizontal dissemination of resistant genes among bacteria.

Artificial regeneration is successful when high performing seedlings are transported with care to the planting site, stored for a short period in an environment without desiccation or fungal growth, and are planted in a deep hole so roots are in contact with moist soil. One of the requirements for success is the ability to avoid common planting mistakes. Due, in part, to use of container stock plus an increase in rainfall, average 1st year survival of pine seedlings (89%) in the southern United States is about 15% greater now than 45 years ago. However, when survival is less than 50% six months after planting, some landowners seek reimbursement for their loss. Some assume poor seedling quality was the cause without realizing that anaerobic soils or sudden freeze events or shallow planting holes or pruning roots, a lack of rain, or underground insects can kill pines. With a focus on pines planted in the southern United States, we list non-nursery factors that have killed seedlings in North America, Africa and Europe.

The urgency to develop vaccines against Covid-19 is putting pressure on the long and expensive development timelines which are normally required for development of lifesaving vaccines. There is a unique opportunity to take advantage of new technologies, smart and flexible design of clinical trials, and evolving regulatory science to speed up vaccine development against Covid-19 and transform vaccine development altogether.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

Viruses with spindle or lemon-shaped virions are rare in the world of viruses, but are common in viruses of archaeal extremophiles, possibly due to the extreme conditions in which they thrive. However, the structural and genetic basis for the unique spindle shape is unknown. The best-studied spindle-shaped virus, SSV1, is composed mostly of the major capsid protein VP1. Similar to many other viruses, proteolytic cleavage of VP1 is thought to be critical for virion formation. Unlike half of the genes in SSV1, including the minor capsid protein gene vp3, the vp1 gene does not tolerate deletion or transposon insertion. In order determine the role of the vp1 gene and its proteolysis for virus function, we developed techniques for site-directed mutagenesis of the SSV1 genome and complemented deletion mutants with vp1 genes from other SSVs. By analyzing these mutants we demonstrate that the N-terminus of the VP1 protein is required, but the N-terminus, or entire SSV1 VP1 protein, can be exchanged with VP1s from other SSVs. However, the conserved glutamate at the cleavage site is not essential for infectivity. Interestingly, viruses containing point mutations at this position generate mostly abnormal virions.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

Multichannel EEGs were obtained from healthy participants in the eyes-closed no-task condition (where the alpha component is typically abolished). EEG dynamics in the two conditions were quantified with two related binary Lempel-Ziv measures of the first principal component and with three measures of integrated information including the more recently proposed integrated synergy. Both integrated information and integrated synergy with model order p=1 had greater values in the eyes closed condition. If the model order of integrated synergy was determined with the Bayesian Information Criterion, this pattern was reversed, and in common with other measures, integrated synergy was greater in the eyes open condition. Eyes open versus eyes closed separation was quantified by calculation of the between-condition effect size. Lempel-Ziv complexity of the first principal component showed greater separation than the measures of integrated information. The performance of the integrated information measures investigated here when distinguishing between indisputably different physiological states encourages caution when advocating for their use as measures of consciousness.

Protein tyrosine phosphatase receptor type E (PTPRE) is a member of the “classical” protein tyrosine phosphatase subfamily and regulates a variety of cellular processes in a tissue-specific manner by antagonizing the function of protein tyrosine kinases. PTPRE plays a tumorigenic role in different human cancer cells, but its role in retinoblastoma (RB), the most common malignant eye cancer in children, remains to be elucidated. Etoposide resistant RB cell lines and RB patients display significant higher PTPRE expression levels compared to chemosensitive counterparts and the healthy human retina, respectively. PTPRE promotor methylation analyses revealed that PTPRE expression in RB is not regulated via this mechanism. Lentiviral PTPRE knockdown (KD) induced a significant decrease in growth kinetics, cell viability, and anchorage independent growth of etoposide resistant Y79 and WERI RB cells. Caspase-dependent apoptosis rates were significantly increased and a re-sensitization for etoposide could be observed after PTPRE depletion. In vivo chicken chorioallantoic membrane (CAM) assays revealed decreased tumor formation capacity as well as reduced tumor size and weight following PTPRE KD. Expression levels of miR631 were significantly downregulated in etoposide resistant RB cells and patients. Transient miR631 overexpression resulted in significantly decreased PTPRE levels and concomitantly decreased proliferation and increased apoptosis levels in etoposide resistant RB cells, impacts mirroring PTPRE KD effects and indicating PTPRE regulation via this miR. Additionally, PTPRE KD led to altered phosphorylation of protein kinase SGK3 and - dependent on the cell line - also AKT and ERK1/2, suggesting potential PTPRE downstream signaling pathways. In summary, these results indicate an oncogenic role of PTPRE in chemoresistant retinoblastoma.

Quantum gravity theories rely on a minimal measurable length for their formulations, which clashes with the classical formulation of the uncertainty principle and with Lorentz invariance from general relativity. These incompatibilities led to the development of the generalized uncertainty principle (GUP) from string theories and its various modifications. GUP and covariant formulations of the uncertainty principle are discussed, together with implications for space-time quantization.

The graphene based highly conductive and flexible devices has received momentous attraction and growth in recent years for potential multifunctional uses. The development of flexible and washable textile sensors, actuators, energy storage and energy harvesting systems. Textile fabrics coated with graphene and conductive polymers have been used for wearable self-powered e-textiles, such as tribo-electric, piezoelectric, and Thermoelectric. Herein this research, 100% woven cotton fabric is Fictionalized with graphene oxide (GO) using industrial-scale cold pad batch dyeing technique for the development of low-grade body heat into self-powered wearable e-textiles. The conductive polymer PEDOT: PSS was coated using layer by layer approach. The study demonstrates that the resultant textile electrodes showed reduced electrical sheet resistance from 2.5 MΩ to 15KΩ, with a reduced graphene oxide and further reduced to (2.5 -12.5 Ω) for conductive polymer. The sheet resistance was decreased with the number of dyeing cycles (10-15) and increased with 20 washing cycles vice versa. The study demonstrates that the sensor response and performance were improved with increasing the content percent of rGO and PEDOT: PSS. The tensile strength of as coated fabric electrodes was improved from (25.0-85.5 mPa) and fabric thickness was increased to (26-38µm) without compromising or influencing the air permeability. The resultant textile electrodes may potentially be used in smart textiles for self-powered flexible wearable generators, sensors, and energy storage. The study demonstrates that the cold pad batch dyeing method is a suitable and effective method for the fabrication of graphene-based textiles.

The study of complex systems deals with emergent behaviour that arises as a result of nonlinear spatio-temporal interactions between a large number of components both within the system, as well as between the system and its environment. There is a strong case to be made that neural systems as well as their emergent behaviour and disorders, can be studied within the framework of complexity science. In particular, the field of neuroimaging has begun to apply both theoretical and experimental procedures originating in complexity science – usually in parallel with traditional methodologies. Here, we demonstrate that the use of such traditional models may distort the outcomes of neuroimaging experiments – hence affecting their interpretability and raising questions about their reliability.Therefore, we argue in favor of adopting a complex systems-based methodology in the study of neuroimaging, alongside appropriate experimental paradigms, and with minimal influences from non-complex systems approaches. Our exposition includes a review of the fundamental mathematical concepts, combined with practical examples and a compilation of results from the literature.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

In recent years, the prevalence of tobacco and electronic cigarette (e-cigarette) use among adolescents has raised significant public health concerns worldwide. This study aims to investigate respiratory symptoms among Polish adolescents. We conducted an online survey among Polish school students from all provinces, collecting data over two months in Spring 2021. Students voluntarily complete the anonymous survey, answering questions about respiratory symptoms, smoking habits (both traditional and electronic cigarettes), and demographic information. Analysis focused on four subgroups: non-tobacco users, traditional cigarette smokers, e-cigarette users, and dual users, totaling 10,388 pupils aged 12-18 years, predominantly attending secondary technical and comprehensive schools. A total of 10388 pupils participated in the study, 55.6 % (5778) of whom were girls and 44.4 % (4610) boys. Adolescents, who admitted using both e-cigarettes and traditional cigarettes experienced more frequent episodes of cough during the day (39.70%) and at night (18.40%) compared to their peers in other groups. Chest discomfort, including pain and pressure, was also reported more often by adolescents, who used e-cigarettes and traditional cigarettes concurrently (27.60%) compared to their peers in other groups. Chest pressure was experienced less commonly by non-smoking adolescents (14.40%) than by smokers (18.90%). Higher severity of cough during the day and at night was observed in the group of adolescents using traditional cigarettes and e-cigarettes concurrently compared to the other groups. The adolescents in the dual user group experienced more severe dyspnoea and wheezing compared to the other groups included in the comparison. The results of this study confirm the correlation between the occurrence of respiratory symptoms in adolescents who smoke cigarettes, use e-cigarettes and in dual users. The respiratory symptoms occur most frequently and are the most severe in the group of adolescents who use e-cigarettes and traditional cigarettes

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Advances in the availability of multitemporal and global built-/human-settlements datasets as derived from Remote Sensing (RS) can now provide globally consistent definitions of “human-settlement” at unprecedented spatial fineness. Yet, these data only provide a time-series of past extents and urban growth/expansion models have not had parallel advances at high-spatial resolution. We present a flexible modelling framework for producing annual built-settlement extents in the near future past last observed extents as provided by RS-based data. Using a random forest and autoregressive temporal models with short time-series of built-settlement extents and subnational level data, we predict annual 100m resolution binary settlement extents five years beyond the last observations. We applied this framework within varying contexts and predicted annual extents from 2010 to 2015. We found that our model framework preformed consistently across all sample countries and, when compared to time-specific imagery, demonstrated the capacity to capture human-settlement missed by the input time-series and validation extents. When comparing building footprints of small settlements to forecast extents, we saw that the modelling framework had a 12 percent increase in ground-truth accuracy. This framework shows promise for predicting near-future settlement extents, and provides a foundation for forecasts further into the future.

Oncogenic protein E6 from Human Papilloma Virus 16 (HPV-16) mediates the degradation of Membrane-associated guanylate kinase with inverted domain structure-1 (MAGI-1), throughout the interaction of its protein binding motif (PBM) with the Discs-large homologous regions 1 (PDZ1) domain of MAG1-1. Generic variation in the E6 gene that translates to changes in the protein’s amino acidic sequence modifies the interaction of E6 with the cellular protein MAGI-1. MAGI-1 is a scaffolding protein found at tight junctions of epithelial cells, where it interacts with a variety of proteins regulating signaling pathways. MAGI-1 is a multidomain protein containing two WW (rsp-domain-9), one guanylate kinase-like, and six PDZ domains. PDZ domains played an important role in the function of MAGI-1 and served as targets for several viral proteins including the HPV-16 E6. The aim of this work was to evaluate, with an in silico approach, employing molecular dynamics simulation and protein-protein docking, the interaction of the intragenic variants E-G350 (L83V), E-C188/G350 (E29Q/L83V), E-A176/G350 (D25N/L83V), E6-AAa (Q14H/H78Y/83V) y E6-AAc (Q14H/I27RH78Y/L83V) and E6-reference of HPV-16 with MAGI-1. We found that variants E-G350, E-C188/G350, E-A176/G350, AAa and AAc increase their affinity to our two models of MAGI-1 compared to E6-reference.

Several pathotypes of enteric E. coli have been identified. The group represented by Shiga toxin-producing E. coli (STEC) is of particular interest. Raw milk and raw milk products are significant sources of STEC infection in humans; therefore, identifying pathogens at the herd level is crucial for public health. Most national surveillance programs focus solely on raw milk and raw milk cheeses that are ready for retail sale, neglecting the possibility of evaluating the source of contamination directly at the beginning of the dairy chain. In order to assess the viability of new molecular methodologies applied to raw milk filters enabling the identification of the presence of STEC serotypes in milk production and apply the same methods to identify the presence of these pathogens in calf feces we analyzed, through a commercial real-time PCR assay, a total of 290 samples coming from 18 different dairy herds; 88 bulk tank milk (BTM), 104 raw milk filters (RMF) and 98 calves’ feces samples. In total 3.4% of BTM, 41.4% of RMF and 73.4% of calves’ feces tested positive for stx presence, supporting our hypothesis that BTM is not a suitable matrix to assess the STEC presence at herd level, underestimating it. Our conclusion is that the surveillance program needs critical and extensive improvements such as RMF and calves’ feces analysis implementation in order to be more efficient in detecting and preventing STEC infections. The epidemiology of these infections and the characteristics of the pathogen clearly show how a One Health approach will be pivotal to improve our capabilities to control the spread of these infections.

The healthcare sector has undergone a profound transformation, owing to the influential role played by IoMT (Internet of Medical Things) technology. However, there are substantial concerns over these devices' security and privacy-preserving nature. Current literature on IoMT tends to focus on specific security features like data confidentiality or data integrity or data availability or access control and most solutions are simulated and not tested in a real-world live network. This paper proposes a smart secure by design solution that safeguards user’s data during health and wellbeing monitoring of patients locally (home, care-home, and hospital) and remotely. The proposed innovative solution is known as Secure by Design Real Time IoMT Architecture for e-Health Population Monitoring (RTPM) for smart hospitals and any healthcare monitoring management. In this system, keys can also be generated by the patient monitoring system independent to maintain high privacy standard and trust during the monitoring process and to enable the IoMT devices run independently even if the server is compromised and are made safe from external exploits to the client nodes. However, the session keys are controlled by the trusted IoMT server to lighten the IoMT devices overheads and the session keys are securely exchanged between the client system and the monitoring server. The proposed RTPM focuses on addressing the major security requirements for an IoMT system: confidentiality, integrity, availability, conducts authentication, protect from DoS attacks and prevent from non-repudiation attack of patient medical data and the devices in a real time, sensory data communication environment for live e-health monitoring. A secure communication is tested by capturing the live network traffic and the system’s performance analysis of RTPM using different security algorithms with different key sizes of RSA, AES, and SHA shows that resource constraint low powered system can also successfully integrate with high-end state-of-the-art secure parameters and features and have the potential to support real time secure interaction. A stress test is also conducted to ensure that the system can withstand huge key sizes and different data types including multi-media information.

Wastewater-based surveillance is emerging as an important tool for COVID-19 pandemic trending. Current methods of wastewater collection, such as grab and auto-composite sampling, have drawbacks that impede effective surveillance, especially from small catchments with limited accessibility. Passive samplers, which are more cost-effective and require fewer resources to process, are promising candidates for monitoring wastewater for SARS-CoV-2. Here, we compared traditional auto sampling with passive sampling for SARS-CoV-2 detection in wastewater. Torpedo-style 3D printed passive sampler device containing both cotton swabs and electronegative filter membranes was used. Between April and June 2021, fifteen passive samplers were placed at a local hospital wastewater outflow alongside an auto sampler. Reverse transcription and quantitative polymerase chain reaction (RT-qPCR) was used to detect SARS-CoV-2 in the samples after processing and RNA extraction. The swab and membrane of the passive sampler showed similar detection rates and Ct values for SARS-CoV-2 RNA for the N1 and N2 gene targets. The passive method performed as well as the grab/auto sampling, with no significant differences between N1 and N2 Ct values. There were discrepant results on two days with negative grab/auto samples and positive passive samples, which might be related to the longer duration of passive sampling in the study. Overall, the passive sampler was rapid, reliable and cost-effective, and could be used as an alternative sampling method for the detection of SARS-CoV-2 in wastewater.

Shiga toxigenic E. coli (STEC) are an important cause of foodborne disease globally with many outbreaks linked to the consumption of contaminated foods such as leafy greens. Existing methods for STEC detection and isolation are time-consuming. Rapid methods may assist in preventing contaminated products from reaching consumers. This proof-of-concept study aimed to determine if a metabolomics approach could be used to detect STEC contamination in spinach. Using untargeted metabolic profiling, the bacterial pellets and supernatants arising from bacterial and inoculated spinach enrichments were investigated for the presence of unique metabolites that enabled categorization of three E. coli risk groups. A total of 109 and 471 metabolite features were identified in bacterial and inoculated spinach enrichments, respectively. Supervised OPLS-DA analysis demonstrated clear dis-crimination between bacterial enrichments containing different risk groups. Further analysis of the spinach enrichments determined that pathogen risk groups 1 and 2 could be easily discriminated from the other groups, though some clustering of risk groups 1 and 2 was observed, likely representing their genomic similarity. Biomarker discovery identified metabolites that were significantly associated with risk groups and may be appropriate targets for potential biosensor development. This study has confirmed that metabolomics can be used to identify the presence of pathogenic E. coli likely to be implicated in human disease.

In 2020, students of Pakistan had to adapt to the online environment for the very first time. This study aims to analyze the perceptions of medical, dental, and allied health students about online education in Pakistan. A descriptive, cross-sectional study was done to assess the level of acceptance of undergraduate students. A pre-validated questionnaire regarding demographics, past-experience of e-learning, advantages disadvantages of e-learning, and general perception of students towards e-learning was distributed. Descriptive statistics were computed for demographics, Mann-Witney-U test was used to compare the differences of perceptions between pre-clinical year and clinical years students. Kruskal-Wallis test was applied to compare the results of three specialties of students. Chi-square was used to compare overall category-wise positive and negative responses of students. 1200 students participated in the study. The major advantage identified by all students was the ‘comfortable environment’ in which they studied online. The major disadvantage selected by preclinical year students was ‘anxiety due to social isolation’ and that chosen by clinical year students was ‘lack of patient interaction’. Overall, 72% of students had a negative perception of e-learning. Student-teacher training, student counselling sessions, and innovative techniques need to be introduced to enhance student engagement and reduce pandemic stress.

In recent years, many libraries and archives have started digitizing their collections thus making maps by Indigenous peoples more easily available for scholars to study. While a number of these maps were discussed by G. Malcolm Lewis in the History of Cartography series (volume 2, book 3, Chapter 4: 1984), more have since been found and disseminated. These maps are critical in understanding the historic and current land tenure of Indigenous groups. Further, Indigenous claims to land can be seen in their connections via toponymy. European concepts of territory and political boundaries did not coincide with First Nation/American Indian views resulting in the mistaken view that Natives did not have formal concepts of their territories. Further, Tribes/First Nations with cross-border territory have special jurisdictional problems. This paper will illustrate how many Native residents were very spatially cognizant of their own lands, as well as neighboring nations’ lands, overlaps between groups, hunting territories, populations, and trade networks. Currently, the Sinixt First Nation provides a perfect example of how an Aboriginal people are inputting and using a GIS representation of their territory with proper toponymy and use areas.

Background and Objectives: In recent years Electronic scooters (E-Scooters) have gained popularity, whether for private use or as a publicly available transportation method. With introduction of these vehicles, reports of E-Scooter related accidents have surged, sparking a public debate and concern. Aim of this study was to analyse epidemiological data, characteristics and severity of traumatic brain injury (TBI) related to E-Scooter accidents. Materials and Methods: This retrospective case series evaluated 28 patients who were admitted to three largest neurosurgery clinics in Riga, Latvia between time period from April to October in two separate years – 2022 and 2023 after an E-Scooter related accident. Data were collected on patient demographics, time of the accident, alcohol consumption, helmet use, type of TBI, other related injuries, treatment and assessment at discharge. Results: A total of 28 patients were admitted with TBI related to E-Scooter use, with median age 30 years (Q1-Q3, 20.25-37.25), four individuals under age of 18, majority (64%) were male. In 23 cases the injury mechanism was fall, in 5 cases collision. None were wearing a helmet at time of injury. Alcohol intoxication was evident in over half of the patients (51.5%), with severe intoxication (>1.2ppm) in 75% cases among them. Neurological symptoms upon admission were noted in 50% of cases. All patients had intracranial trauma - 50% brain contusions, 43% traumatic subdural hematoma, almost 30% - epidural hematoma. Craniofacial fractures were evident in 71% of cases, fractures in other parts of body in 3 patients. 6 patients required emergency neurosurgical intervention. Neurological complications were noted in 2 patients, 1 patient died. Conclusions: E-Scooter related accidents result in a significant number of brain and other associated injuries, with notable frequency linked to alcohol influence and lack of helmet use. Prevention campaigns to raise awareness of potential risks and implementation of more strict regulations should be done.

Diabetic foot ulcers (DFUs) significantly affect the lives of patients and increase the risk of hospital stay and amputation. We suggest a remote-monitoring platform for better DFU care. This system uses digital health metrics (scaled from 0 to 10, where higher scores indicate a greater risk of slow healing) to provide a comprehensive overview through a visual interface. The platform features smart offloading devices that capture behavioral metrics such as offloading adherence, daily steps, and cadence. Coupled with remotely measurable frailty and phenotypic metrics, it offers an in-depth patient profile. Additional demographic data, wound characteristics, and clinical parameters, such as cognitive function, were integrated, contributing to a comprehensive risk factor profile. We evaluated the feasibility of this platform with 124 DFU patients over 12 weeks; 39% experienced unfavorable outcomes such as dropout, adverse events, or non-healing. Digital biomarkers were benchmarked (0-10), categorized into low, medium, and high risk for unfavorable outcomes, and visually represented using color-coded radar plots. The initial results of case reports illustrate the value of this holistic visualization to pinpoint the underlying risk factors for unfavorable outcomes, including a high number of steps, poor adherence, and cognitive impairment. Although future studies are needed to validate the effectiveness of this visualization in personalizing care and improving wound outcomes, early results in identifying risk factors for unfavorable outcomes are promising.

Technological advances in the last decades have led to the realization of the concept of a smart environment. A significant part of this development is decentralized ledger technology and its variant, a blockchain. The blockchain database is immutable, open to all stakeholders, secure by architecture and robust. Applying a blockchain in water supply sanitary control creates opportunities for optimization, higher quality of service, cost reduction, better sanitary standards and public control. Physical, chemical, and biological water supply contamination is a great source of public health hazards. Implementation of a blockchain for water supply IoT, from the source point to the consumption point, enables effective response to changing environments, possible cross-contamination, stormwater management or disaster and emergency action. The chapter encompasses all fundamental elements and principles of water collection, distribution and consumption, with a focus on the health hazards and sanitary requirements for potable water. The chapter listed the main contaminants, methods of their registration and elimination, and requirements for drinking water in accordance with WHO, EU Drinking Water Directive and EPA standards. Blockchain technology solutions are described for smart water supply, including smart supply management, smart contracts, tokenization, smart compliance systems, and, most importantly, effective utilization of distributed ledger technologies for sanitary monitoring of water sources, water treatment, and water distribution systems.

The relentless challenges posed by the COVID-19 pandemic have placed immense pressure on densely populated regions, such as Hong Kong, particularly in the context of an aging population. The burgeoning demand for healthcare services has necessitated the optimization of resource al-location within healthcare systems. This research presents an innovative analytical queueing model specifically tailored to address the intricate gridlock dynamics prevalent in healthcare systems, with a focused application in the challenging landscape of COVID-19 management. Hong Kong, like numerous other regions, has experienced a demo-graphic transition leading to heightened healthcare demands. Traditional methodologies for scrutinizing gridlock issues in healthcare settings, including simulation models, often prove suboptimal within the context of sophisticated optimization frameworks. This study, however, delves into analytical queueing models, offering a more efficient and effective approach. These models have been underexplored, primarily due to the intricacies involved in modeling gridlock propagation within restricted capacity, a critical concern magnified by the COVID-19 pandemic. The novel Queueing Model introduced in this research incorporates the maintenance of queue capacities and topological aspects as exogenous parameters, rendering it exceptionally adaptable for diverse gridlock-related applications. This adaptability is especially pertinent to healthcare management during the COVID-19 crisis. The model meticulously integrates the concept of gridlock, furnishing a comprehensive comprehension of its origins and repercussions. Validation of this model involves rigorous comparison with established methodologies, exact results, and simulation data, consistently high-lighting its versatility and precision. By applying the model to healthcare management, we scrutinize the dynamics of patient flow within a Hong Kong hospital, placing specific emphasis on the critical issue of bed blockage, further exacerbated by the COVID-19 pandemic. The model's gridlock decomposition unearths the nuanced impact of bed blockage on distinct hospital units, addressing the imperative requirement for quantifying in-patient bed blockage within healthcare systems during a pandemic.

High-resolution forecasting of vegetation type shifts may prove essential for anticipating and mitigating the impacts of future climate change on bird populations. Here, we used the US Forest Service Ecological Response Unit (ERU) classification to develop and assess vegetation-based breeding habitat profiles for eight owl species occurring in foothills and mountains of the southwestern US. Shifts in mapped habitat were forecast using an ecosystem vulnerability model based on the pre-1990 climate envelopes of ERUs and the A1B moderate IPCC emission scenario of future climate. For five of the eight owl species, regional breeding habitat extent was projected to decline by at least 60% by 2090. Three species, the boreal owl (Aegolius funereus; at the trailing edge of its distribution), flammulated owl (Psiloscops flammeolus), and northern pygmy-owl (Glaucidium gnoma) were projected to experience the steepest habitat-loss rates, or 85%, 85%, and 76%, respectively. Projected vegetation shifts overlaid with well-documented flammulated owl breeding populations showed complete or near complete loss of habitat by 2090 in areas of montane forest currently supporting dense aggregations of owl territories. Generalist or lower-elevation owl species were predicted to be less impacted, while for the whiskered screech-owl (Megascops trichopsis), the contraction of current habitat was nearly offset by a projected northward expansion. In general, the results of this study suggest high exposure to climate change impacts for upper-elevation forest owls of semi-arid southwestern North America. Long distance migration and low natal philopatry may prove important to some montane owl populations for adapting to regional loss of habitat.

We report a broadband radio frequency (RF) channelizer with up to 92 channels using a coherent microcomb source. A soliton crystal microcomb, generated by a 49 GHz micro-ring resonator (MRR), is used as a multi-wavelength source. Due to its ultra-low comb spacing, up to 92 wavelengths are available in the C band, yielding a broad operation bandwidth. Another high-Q MRR is employed as a passive optical periodic filter to slice the RF spectrum with a high resolution of 121.4 MHz. We experimentally achieve an instantaneous RF operation bandwidth of 8.08 GHz and verify RF channelization up to 17.55 GHz via thermal tuning. Our approach is a significant step towards the monolithically integrated photonic RF receivers with reduced complexity, size, and unprecedented performance, which is important for wide RF applications ranging from broadband analog signal processing to digital-compatible signal detection.

The adverse relationship between viral hepatitis and pregnancy in developing countries was seen as a reflection of retrospective biased hospital-based data collection by the West. However, the discovery of HEV from an epidemic of non-A, non-B hepatitis in Kashmir and documenting increased incidence and severity of hepatitis E in pregnancy from a house-to-house survey unmasked the unholy alliance. Among the family of HEV’s, genotype (gt)-1, with a unique ORF4-encoded protein enhancing viral polymerase activity and viral replication, is the sole HEV that shows this adverse relationship. The epidemics caused by HEV-gt1 and not by HEV-gt2 show adverse relationship with pregnancy. The pathogenesis of the unholy alliance is complex and at present not well understood. Possibly multiple factors play a role in causing severe liver disease in the mother including: infection, replication and damage to the maternal-foetal interface by HEV-gt1; vertical transmission of HEV to foetus causing severe foetal/neonatal hepatitis; and combined viral and hormone related immune dysfunction of diverse nature in the mother promoting viral replication. Management is multidisciplinary and needs a close watch for the development and management of ALF. Preliminary data suggest beneficial maternal outcomes by early termination of pregnancy in patients with lower grades of encephalopathy.

Recently, the concept of participatory democracy developed in the early 1970s has come back into fashion to revitalize the public involvement in political decision-making processes. Public par-ticipation in forest policy has been fully conceptualized by the scientific community in the late 1990s and early 2000s, but in many contexts the practical application remains unfulfilled. The aim of this study is to identify and analyze the participatory techniques used in literature to increase knowledge and facilitate its transferability into forest policies and strategies. A literature review was carried out to offer an overview of the participatory techniques adopted in the deci-sion-making process. At the end of literature review, 25 participatory techniques were identified based on over 2,000 publications. Afterwards, the participatory techniques were assessed using seven indicators (degree of participation, type and number of participants, time scale, cost, po-tential influence on policy). The results showed that the type of actors involved in the participa-tory technique is a key variable for the complexity and usefulness of the process, while the number of participants influences how information is disseminated. The Principal Component Analysis highlighted that the participatory techniques can be divided in three groups: the first group includes those techniques with a high degree of participation and a contextual high po-tential influence on policies, the second one includes techniques with a costs in terms of re-sources, while the third one consists of those with a large number of participants and reduced time requirements.

For some persistent pollutants, such as recalcitrant pesticides, the polluted water (urban, agricultural and/or industrial) treated by conventional wastewater treatment plants is in some cases insufficient to achieve the legally required level of purity. This issue is of particular concern in areas where low rainfall does not provide sufficient water resources to meet the needs of agriculture, requiring increased reuse of water from wastewater treatment plants. In this context, Advanced Oxidation Processes (AOPs) hold great promise for the removal of organic pollutants. This study first evaluates the effectiveness of UV/S2O8= compared to heterogeneous photocatalysis using UV/TiO2 processes on the degradation of two commonly used herbicides (terbutylazine and isoproturon) in aqueous solutions using a photoreactor. In addition. the effect of UV wavelength on the degradation efficiency of both herbicides was investigated. Although degradation rate was higher under UV-254/S2O8= nm than under UV-365/S2O8= nm, complete degradation of the herbicides (0.2 mg L-1) was achieved within 30 min under UV-366 nm using a Na2S2O8 dosage of 250 mg L-1 in the absence of inorganic anions. To assess the impact of water matrix, the individual and combined effects of sulphate, bicarbonate and chloride were evaluated. They can react with hydroxyl and sulphate radicals formed during AOPs to form new radicals with a lower redox potential. The results showed negligible effects of sulphate, while the combination of bicarbonate and chloride seemed to be the key for the decrease in herbicide removal efficiency found when working with complex matrices. Finally, the main intermediates detected during the photodegradation process were identified and the likely pathways are proposed and discussed.

In this study, a critical review was carried out using the Web of ScienceTM Core Collection database to analyse the scientific literature published to date to identify lines of research and future perspectives on the presence of chemical pollutants in beer brewing. Beer is one of the world's most popular drinks and the most consumed alcoholic beverage. However, a widespread challenge with potential implications for human and animal health is the presence of physical, chemical and/or microbiological contaminants in beer. Biogenic amines, heavy metals, mycotoxins, nitrosamines, pesticides, acrylamide, phthalates, bisphenols, microplastics and, to a lesser extent, hydrocarbons (aliphatic chlorinated and polycyclic aromatic), carbonyls, furan-derivatives, polychlorinated biphenyls and trihalomethanes are the main chemical pollutants found during the beer brewing process. Pollution sources include raw materials, technological process steps, the brewery environment and packaging materials. Different chemical pollutants have been found during the beer brewing process, from barley to beer. Brewing steps such as steeping, kilning, mashing, boiling, fermentation and clarification are critical in reducing the levels of many of these pollutants. As a result, their residual levels are usually below the maximum levels allowed by international regulations.

Threats to natural ecosystems are closely linked to human development, and the lack, insufficiency or inefficiency of public policies are some of the most important drivers of negative effects on the environment. The contribution of the IUCN’s Red List of Ecosystems (RLE) to conservation topics has been discussed in previous studies; however, to date its implications for conservation in public policies have not been addressed. This perspective discusses how the RLE may support the improvement and development of these policies, specifically through the implications for public policy of each of the criteria that substantiate the threat status of ecosystems. We aim to provide a plausible baseline to the operationalization of RLE in public and conservation policy, facilitating the work of governments, practitioners and decision makers. Finally, we provide recommendations and examples as to how to proceed in creating and modifying different public policy instruments, such as land-use planning, spatial zoning, tax reduction, compensation schemes, climate change adaptation plans, management of introduced species, development offsets and restoration investment. This perspective contributes to implement RLE into public policy and to improve ecosystem conservation by expanding the current scope of RLE into practical and political dimensions through plausible actions, policies and strategies.

Cyclic STAT3 decoy (CS3D) is a second-generation, double-stranded oligodeoxynucleotide (ODN) that mimics a genomic response element for signal transducer and activator of transcription 3 (STAT3), an oncogenic transcription factor. CS3D competitively inhibits STAT3 binding to target gene promoters, resulting in decreased expression of proteins that promote cellular proliferation and survival. Previous studies have demonstrated antitumor activity of CS3D in preclinical models of solid tumors. However, prior to entering human clinical trials, the efficiency of generating the CS3D molecule and its stability in biological fluids should be determined. CS3D is synthesized as a single-stranded ODN and must have its free ends ligated to generate the final cyclic form. In this study, we report a ligation efficiency of nearly 95 percent. The ligated CS3D demonstrated a half-life of 7.9 hours in human serum, indicating adequate stability for intravenous delivery. These results provide requisite biochemical characterization of CS3D that will inform upcoming clinical trials.

According to the World Health Organization, approximately 20 million people worldwide are infected annually with the hepatitis E virus (HEV). There are 4 main genotypes of HEV. Genotype 1 and genotype 2 are common in developing countries and are transmitted by contaminated water from a fecal-oral route. Genotype 3 and genotype 4 are common in developed countries and can lead to occasional transmission to humans by undercooked meat. Hepatitis E virus 1 and HEV3 can lead to fulminant hepatitis, and HEV3 can lead to chronic hepatitis and cirrhosis in immunocompromised patients. The majority of patients with HEV infection are asymptomatic and usually have spontaneous viral clearance without treatment. However, infection in immunocompromised individuals can lead to chronic HEV infection. Both acute and chronic HEV infections can have extrahepatic manifestations. No specific treatment is required for acute HEV infection, no treatment has been approved in chronic infection and no HEV vaccine has been approved by the (United States) Food and Drug Administration. This review focuses on the molecular virology (HEV life cycle, genotypes, model systems, zoonosis), pathogenesis, clinical manifestation, and treatment of chronic HEV infection, especially in immunocompromised patients, to provide clinicians a better understanding of the global distribution of these infections and the significant effect they can have on immunocompromised patients.

Proposed fundamental laws of biology and a model of health and disease underscore the importance of the lymphatic system. The lymphatics are responsible for two of the laws of biology and the fulcrum of health and disease balancing proliferation with regeneration through the immune system. It is responsible for protection from the environment and repair of senile and damaged tissue. Life is constantly bombarded by forces that increase entropy. Lymphatics provide negative entropy to maintain health. Lymphatics help maintain cellular homeostasis removing products of metabolism. Using these principles, the role of lymphatics is investigated in salt sensitivity hypertension, cardiorenal system, the new pillar of heart failure and kidney disease - Sodium-Glucose Transport Protein 2 (SGLT2) Inhibitors, and brain diseases. The realization of organ lymphatics in maintenance of health and disease opens the avenue to new therapeutics. This is the unrealized potential of lymphatic study.

Natural host defensins, also sometimes termed antimicrobial peptides, are evolutionarily conserved. They have been studied as antimicrobials, but some pharmaceutical properties, undesirable for clinical use, led to the development of synthetic molecules with constructed peptide arrangements and/or peptides not found in nature. The leading development currently is synthetic small molecule nonpeptide mimetics, whose physical properties capture the characteristics of the natural molecules, and share their biological attributes. We studied brilacidin, an arylamide of this type, for its activity in vitro against fungi (40 clinical isolates, 20 species) that the World Health Organization has highlighted as problem human pathogens. We find antifungal activity at low concentrations for many pathogens, which indicates further screening for activity, particularly in vivo, is justified to evaluate this compound, and other mimetics, as attractive leads for development of effective antifungal agents.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

Mallios and Zafiris emphasize that adjoint functors or adjunctions are not only "ubiquitous" in category theory but characterize the naturality of their approach to physical geometry. Hence in this paper, the history and theory of adjoint functors is investigated. Where do adjoint functors come from mathematically and how did the concepts develop historically?

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

Whistler mode waves play a major role in regulating the lifetime of trapped electrons in the Earth's radiation belts. Specifically, whistler mode hiss waves are one of the mechanisms that maintains the slot region between the inner and outer radiation belts. The generation mechanism of hiss is a topic still under debate with at least three prominent theories present in the literature. Lightning generated whistlers in their ducted or non-ducted modes, are considered to be one of the possible sources of hiss. We present a study of new observations from the Radio Receiver Instrument (RRI) on the Enhanced Polar Outflow Probe (ePOP: currently known as SWARM-E). RRI consists of two orthogonal dipole antennas, which enables polarization measurements, when the satellite boresight is parallel to the geomagnetic field. Here we present 75 passes of ePOP - RRI from 2014 - 2018, in which lightning whistlers and hiss waves were observed. In more than 50% of those passes hiss is found to co-exist with the lightning whistlers. Moreover, the whistler observations are correlated with observations of wave power at the lower-hybrid resonance. The observations and a whistler mode ray-tracing study suggest that multiple-hop lightning induced whistlers can be a source of hiss and plasma instabilities in the magnetosphere.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

Logical information theory is the quantitative version of the logic of partitions just as logical probability theory is the quantitative version of the dual Boolean logic of subsets. The resulting notion of information is about distinctions, differences, and distinguishability, and is formalized using the distinctions (`dits') of a partition (a pair of points distinguished by the partition). All the definitions of simple, joint, conditional, and mutual entropy of Shannon information theory are derived by a uniform transformation from the corresponding definitions at the logical level. The purpose of this paper is to give the direct generalization to quantum logical information theory that similarly focuses on the pairs of eigenstates distinguished by an observable, i.e., qudits of an observable. The fundamental theorem for quantum logical entropy and measurement establishes a direct quantitative connection between the increase in quantum logical entropy due to a projective measurement and the eigenstates (cohered together in the pure superposition state being measured) that are distinguished by the measurement (decohered in the post-measurement mixed state). Both the classical and quantum versions of logical entropy have simple interpretations as "two-draw" probabilities for distinctions. The conclusion is that quantum logical entropy is the simple and natural notion of information for quantum information theory focusing on the distinguishing of quantum states.

Field of ResearchThis research study investigates the role of distributed leadership and culture within small enterprises in Malta, an area in which there has been very limited research. It focuses on the interaction between these two elements and their impact on organizational behaviour and effectiveness. Several studies (Jardon et al 2019; Cope et al., 2011; de Oliveira et al., 2015; Mohanty et al., 2012;) suggest that effective leadership and culture are vital elements in the successful endeavours of small organizations. Schein (2006) further asserts that they are two different faces on the same coin and the dyadic interaction characterizes “how leaders create culture and how culture defines and creates leaders”. Distributed Leadership is a systematic practice of interactions and synergies between leaders, followers, and the situation (Spillane 2013). It is different from traditional leadership, which involves top-down management because it tends to be more democratic and participatory, whereby influence and decision-making are shared among multiple individuals rather than being controlled by a single leader. (Xhemajli et al. 2022) MethodologyAdopting a naturalistic approach and guided by an interpretivist, constructivist epistemological stance, this research delves into the intricate interplay between leadership and culture within small businesses. The chosen research methodology employs Grounded Theory, recognized for its robust and systematic process facilitating the observation of patterns through intensive iterative and highly analytical procedures (Charmaz, 2015).In the initial stages of field research, characterized by 'responsive interviewing' (Rubin and Rubin, 2012), data sampling commenced with convenience sampling. This initial phase gradually evolved into a refined strategy incorporating selective sampling and theoretical sampling (Corbin and Strauss, 2015). The shift in sampling approaches reflects a deliberate focus on collecting data based on its specific contribution to the development and comprehension of the dimensions, properties, and characteristics of key concepts.The induction of theory is a product of successive comparative analyses, involving the systematic comparison of data points to identify both similarities and variations. Abductive reasoning is integral throughout the analytical process, with particular emphasis during constant comparative analysis of categories, leading to theoretical integration (Charmaz, 2006). This meticulous approach aligns with the assertion of Strauss and Corbin (2015) that grounding theory in data enhances the likelihood of deriving theories that authentically reflect reality.The key advantage of using this approach is that the analysis carried out goes beyond deep exploration and rich description and actually develops a framework that explains the phenomena observed (Parker and Roffey, 1997, p.218). This is very important if the findings are to contribute to the knowledge enhancement of any field of practiceThe culmination of this research effort is the presentation of a set of interconnected concepts, intricately woven together into an emergent parsimonious model (Corbin and Strauss, 2015). This model serves to explain the dynamic interplay between leadership and culture, elucidating its tangible impact on the effectiveness of small enterprises. Research Contribution:Implications for PracticeThis research contributes to the literature on leadership and organizational culture in small enterprises, particularly in the context of Malta where such studies are scarce. By providing an initial exploration of these phenomena and their impact on organizational behavior, this paper lays the groundwork for further inquiry into this important area. Furthermore, the study offers practical insights for leaders of small enterprises by elucidating leadership behaviors observed in established organizations. Through applied cases, it demonstrates how the abstract concept of culture can be translated into a practical instrument that supports leadership and organizational development. This not only enriches the understanding of leadership dynamics but also provides tangible strategies for implementation. Moreover, the research contributes empirical evidence on the development of leadership functions within small enterprises, emphasizing the potential of shared and distributed leadership models. By grounding its findings in data, the study equips leaders with a deeper understanding of how these leadership approaches can shape organizational development, fostering more effective management practices in small businesses. Methodologically, the adoption of Grounded Theory methodology showcases its efficacy in exploring complex management phenomena. By employing this approach, the researchers were able to gather rich descriptions and develop an explanatory framework, highlighting its applicability in studying nuanced organizational dynamics. Implications for Policy and TheoryThis research also holds significant implications for policymakers, academic researchers and institutions involved in supporting small businesses. By providing insights into distributed leadership and cultural influences on organizational effectiveness, it offers a basis for informed policy formulation and support mechanisms. The conceptual model emerging from this study serves as a foundation for designing more targeted policies that cater to the unique needs of small enterprises. By understanding the intricacies of leadership dynamics and cultural contexts, policymakers can develop interventions that foster a conducive environment for small business growth and sustainability. Additionally, academic researchers can use these findings to further refine theoretical frameworks and empirical studies in the field, contributing to ongoing scholarly dialogue and knowledge advancement.

Micro-combs [1-4] - optical frequency combs generated by integrated micro-cavity resonators – offer the full potential of their bulk counterparts [5,6], but in an integrated footprint. The discovery of temporal soliton states (DKS – dissipative Kerr solitons) [4,7-11] as a means of mode-locking micro-combs has enabled breakthroughs in many fields including spectroscopy [12,13], microwave photonics [14], frequency synthesis [15], optical ranging [16,17], quantum sources [18,19], metrology [20,21] and more. One of their most promising applications has been optical fibre communications where they have enabled massively parallel ultrahigh capacity multiplexed data transmission [22,23]. Here, by using a new and powerful class of micro-comb called “soliton crystals” [11], we achieve unprecedented data transmission over standard optical fibre using a single integrated chip source. We demonstrate a line rate of 44.2 Terabits per second (Tb/s) using the telecommunications C-band at 1550nm with a spectral efficiency – a critically important performance metric - of 10.4 bits/s/Hz. Soliton crystals exhibit robust and stable generation and operation as well as a high intrinsic efficiency that, together with a low soliton micro-comb spacing of 48.9 GHz enable the use of a very high coherent data modulation format of 64 QAM (quadrature amplitude modulated). We demonstrate error free transmission over 75 km of standard optical fibre in the laboratory as well as in a field trial over an installed metropolitan optical fibre network. These experiments were greatly aided by the ability of the soliton crystals to operate without stabilization or feedback control. This work demonstrates the capability of optical soliton crystal micro-combs to perform in demanding and practical optical communications networks.

Coral reefs are critical ecosystems globally for marine fauna, biodiversity and through the services they provide to humanity. However, they are significantly threatened by anthropogenic stressors, such as climate change. By combining 9 environmental variables and ecological and health-based thresholds obtained from the available literature, we develop, using fuzzy logic (discontinuous functions), a Coral Reef Stress Exposure Index (CRSEI) for remotely monitoring coral reef exposure to environmental stressors. Our approach capitalises on the abundance of readily available satellite Earth Observation (EO) data available in the Google Earth Engine (GEE) cloud-based geospatial processing platform. CRSEI values from 3157 distinct reefs were generated and mapped across 12 important coral reef ecosystem regions. Quantitative analyses indicated that the index detected significant temporal differences in stress and was, therefore, able to capture historic change at a global scale. We also applied the CRSEI to three case-study reef ecosystems, previously well-monitored for stress and disturbance using other methods. PCA analysis indicated that depth, current, sea surface temperature (SST) and SST anomaly accounted for the greatest contribution to the variance in stress in these three regions. The CRSEI corroborated temporal and spatial differences in stress exposure from known disturbances within these reference regions, in addition to identifying the potential drivers of inter- and intra-region differences in stress, namely depth, degree heating weeks and SST anomaly. We discuss how the index can be further improved in future with site-specific thresholds for each stress variable, and the incorporation of additional variables not currently available in GEE. This index provides an open access tool, built around a free and powerful processing platform, that has broad potential to assist in the regular monitoring of our increasingly imperilled coral reef ecosystems, and, in particular, those that are remote or inaccessible.

This study analyzes the eating behavior and factors associated with the presence of disordered eating attitudes in patients undergoing bariatric surgery. It is a cross-sectional, descriptive, and analytical study conducted at a hospital in the Amazon region of Brazil. The Disordered Eating Attitude Scale reduced version (DEAS-s) was used to assess the risk of eating disorders and the Three-Factor Eating Questionnaire (TFEQ-R21) to characterize eating behavior. A total of 205 patients participated, with a mean age of 37.5 ± 8.6 years, the majority being female (93.7%; p<0.001), the mean BMI was 45.3±6.7 kg/m2. It was found that cognitive restraint had the highest mean (52.6±19.9; p<0.001). As for the DEAS-s, the question with the highest mean was "spending one or more days without eating or consuming only liquids to lose weight" (2.80±1.99). Female participants had a higher score in the emotional eating (p=0.016). Disordered eating attitudes showed a correlation with emotional eating and uncontrolled eating. These results suggest that candidates for bariatric surgery may have susceptibility to eating disorders. The importance of a multidisciplinary team in monitoring during the preoperative period is highlighted.

Elevated immunoglobulin E (IgE) levels are commonly associated with allergies. However, high IgE levels are also found in several other infectious and non-infectious disorders. Elevated IgE levels typically suggest allergies, eczema, or recurrent skin infections. Very high IgE levels are uncommon in patients with active eczema but typically reflect a monogenic atopic condition or inborn immune defects with an atopic phenotype. The aim of our research is to identify if the possible cause of high IgE levels is also dependent on external factors, age, or associated recurrent pathologies such as infections. To answer this question, we performed a one-year retrospective study that included 200 hospitalized children who had at least two viral or bacterial infections in the six months preceding hospitalization. Measurements of IgE and allergen panels (respiratory and digestive) using blood samples revealed that individuals who tested positive for the body’s synthesis of hyperimmunoglobulin E were not observably allergic to any potential allergens despite having higher total serum IgE. According to the results, there was a strong correlation between elevated IgE serum levels and a history of infectious diseases among the patients.

The background of this research is the environmental sustainability assessments in the aviation ecosystem, particularly concerning airports, are getting significant attention from the industry, regulators, and researchers. A standardized and comprehensive approach is essential for uniformly addressing the global impacts of these assessments across the industry. The main objective of this study is to develop a unique framework that encompasses the requirements of aviation regulators as well as industry and academic metrics, aiming for a standardized approach to environmental sustainability assessments at airports. The methodology used the Sum of Ranking Method to evaluate each environmental indicator precisely. It was applied to five airports globally, providing a diverse testing ground to assess the proposed metrics’ applicability and effectiveness and validate the framework. The results showed that applying the framework across these varied airport environments demonstrated its viability and effectiveness, indicating that it can be successfully applied to different airport realities. The conclusion shows that the developed framework can be successfully applied globally, suggesting that it can be a valid method for international adoption in environmental airport sustainability analysis, offering a standardized approach that could be accepted and utilized worldwide.

Eucalyptus, a therapeutic plant mentioned in the ancient Algerian pharmacopeia, specifically two species belonging to the Myrtaceae family - E. radiata and E. cinerea, were investigated in this study for their antibacterial, antioxidant, and anti-inflammatory properties. The study used aqueous extracts (AE) obtained from these plants, and the extraction yields were found to be dif-ferent. The in vitro antibacterial activity was evaluated using a disc diffusion assay against three typical bacterial strains. The results showed that E. radiata EAq was effective against all three strains, while E. cinerea EAq was only effective against E. coli. Both extracts displayed significant antioxidant activity compared to BHT. The anti-inflammatory impact was evaluated using a pro-tein (BSA) inhibition denaturation test. The E. radiata extract was found to inhibit inflammation by 75% at a concentration of 250 g/ml, significantly higher than the placebo. Ellagic acid, a pri-mary phytochemical found in the extracts, demonstrated noteworthy toxic and pharmacokinetic characteristics and a maximum binding energy of -7.53 kcal/mol for its anti-TyrRS activity in sili-co. The study suggests that the extracts and their primary phytochemicals could enhance the effi-cacy of antibiotics, antioxidants, and non-steroidal anti-inflammatory drugs (NSAIDs). As phar-maceutical engineering experts, we believe this research contributes to developing natural-based drugs with potential therapeutic benefits.

1) Background: Several studies have shown the benefit of drawing when learning anatomy. Virtual Reality (VR) also appears to be useful to increase the understanding of the location of anatomical structures. This study aims to describe how students in an Operating Room Nursing (OR nursing) master study program perceive the benefit of active learning methods, including drawing and the use of VR. 2) Methods: We combined these two methods in a class of 29 students. 38 half-finished drawings of anatomical structures were made. The students were to complete these during lectures with guidance from the teacher. The students also attended a two-hour VR session where they were to find various anatomical structures. A paper questionnaire was applied to evaluate the teaching program. Data were analyzed statistically. 3) Results: The students highly appreciated these learning methods. They reported that drawing made them work more actively during lectures and increased their learning outcome. They also perceived that the use of VR technology increased their understanding of the location of anatomical structures. 4) Conclusion: The combination of drawing and VR technology may be of benefit to OR Nursing students when learning anatomy by both increasing student activity and learning outcomes.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

This paper reports on the optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment; Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating assisted hybrid (photovoltaic-battery-generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.

How complex morphological patterns form is an intriguing question in developmental biology. However, the mechanisms that generate complex patterns remain largely unknown. Here we sought to identify the genetic mechanisms that regulate the tan (t) gene in a multi-spotted pigmentation pattern on the abdomen and wings of Drosophila guttifera. Previously, we showed that yellow (y) gene expression completely prefigures the abdominal [1] and wing [2] pigment patterns of this species. In the current study, we demonstrate that the t gene is co-expressed with the y gene in nearly identical patterns, both transcripts foreshadowing the adult abdominal and wing melanin spot patterns. We identified cis-regulatory modules (CRMs) of t, one of which drives reporter expression in six longitudinal rows of spots on the developing pupal abdomen, while the second CRM activates the reporter gene in a spotted wing pattern. Comparing the abdominal spot CRMs of y and t, we found a similar composition of putative transcription factor binding sites that are thought to regulate the complex expression patterns of both terminal pigmentation genes y and t. In contrast, the y and t wing spots appear to be regulated by distinct upstream factors. Our results suggest that the D. guttifera abdominal and wing melanin spot patterns have been established through the co-regulation of y and t, shedding light on how complex morphological traits may be regulated through the parallel coordination of downstream target genes.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

Background: This study assessed the nature of healthcare services offered in the David Umahi Federal University of Health Sciences health clinic and students' disposition to access the facility. Objectives: To assess the knowledge, attitude and practice of students in accessing healthcare services in the David Umahi Federal University of Health Sciences health clinic.Methods: Used cross-sectional design, a structured questionnaire of a five-point Likert scale as a veritable instrument for collecting the data from 50 student respondents. The questionnaire is made up of four key sections comprising student’s demographic parameters, knowledge, attitude and practice of both students and the clinic staff. Data collected was analyzed in a table of descriptive statistics to determine the total, range, mean and median, which were used to ascertain students’ utilization/accessibility disposition, perception of barriers to accessing healthcare service and overall viability of the clinic.Results: The mean value outcome of knowledge of students falls between 3.1 and 3.9, the mean value for attitude of students falls between 2.5 to 3.4 and 4.0, while the practice of students falls between mean values 2.6 and 3.1. Most of these outcomes represent poor or weak weight factor which requires several levels of intervention.Conclusion: This study highlights the overriding importance of the university healthcare clinic in maintaining a healthy study season among students of David Umahi Federal University of Health Sciences and their health-seeking behaviour. This helps to promote health, attract higher intakes and retain them in the institution till graduation.

The new logic of partitions is dual to the usual Boolean logic of subsets (usually presented only in the special case to the logic of propositions) in the sense that partitions and subsets are category-theoretic duals. The new information measure of logical entropy is just the normalized quantitative version of partitions. The new approach to interpreting quantum mechanics (QM) is showing that the mathematics (not the physics) of QM is the Hilbert space version of the mathematics of partitions. Or putting it the other way around, the math of partitions is a skeletal version of the math of QM. The key concepts throughout this progression from logic to information theory to quantum theory are distinctions versus indistinctions, definiteness versus indefiniteness, or distinguishability versus indistinguishability. The distinctions of a partitions are the ordered pairs of elements from the underlying set that are in different blocks of the partition. Logical entropy is defined (initially) as the normalized number of distinctions. The cognate notions of definiteness and distinguishability run through the math of QM, e.g., in the key non-classical notion of superposition (= ontic indefiniteness) and in the Feynman rules for adding amplitudes (indistinguishable alternatives) versus adding probabilities (distinguishable alternatives).

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Modern organic synthesis is majorly focused on developing environmentally benign synthetic protocols by employing green chemistry principles. Accordingly, in our recent research work, we herein report the use of modified supramolecular host cyclodextrin as an effective solid based green catalyst for accessing structurally diverse and medicinally relevant pyrimidone architectures. The catalyst and the synthesized compounds 4 (a-r) were characterized using FT-IR, NMR and GC-Mass spectroscopy. Major highlights of the reported work include: atom economical process, extremely milder reaction conditions, operational simplicity, high isolated yields, and excellent catalyst turnover number. The molecular docking studies suggest that the compound 4n has the hydrogen bonding, hydrophobic and π-pair interactions with the active site of active sites of CXT M 15 receptor.

The research presents the inter-comparison of atmospheric variables measured by 9 automatic meteorological stations. This set of data was compared with the measurements of other meteorological stations in order to standardize the values that must be adjusted when taken to different areas. The data of a set of a total of 9 GMX500, which measures conventional meteorological variables, and 10 WS100 sensors, which measures precipitation parameters. The automatic stations were set up at the Huancayo Observatory (Geophysical Institute of Peru) for a period of 5 months. The data set of GMX500 were evaluated comparing with the average of the 9 sensors and the WS100 was compared with a optical disdrometer Parsivel2. The temperature, pressure, relative humidity, wind speed, rainfall rate, and drop size distribution was evaluated. A pair of GMX500 sensors presented high data dispersion, it was found found that the errors came from a bad configuration; once this problem was solved, good agreement was archived, with low RMSE and high correlation. I was found that the WS100 sensors overestimate the precipitation with a percent bias close to 100% and the differences increase with the greater intensity of rain. The DSD retrieved by WS100 have unrealistic behavior with higher concentrations in diameters of 1 mm and 5 mm, in addition to a flattened curve.

There are potentially promising mitigation activities for epidemic and pandemic scenarios that are not currently the subject of significant research effort. Large epidemics and pandemics pose risks that are important to mitigate, even if the likelihood of the events is low and uncertain. While some efforts are the subject of extensive funding and consideration, other approaches are neglected. Here, we consider such neglected interventions which could significantly reduce the impact of such an epidemic or large-scale pandemic. These are identified via a narrative literature review of extant literature reviews and overviews of mitigations in epidemic and pandemic situations, followed by consideration of the economic value of information of further study of heretofore neglected interventions and approaches.Based on that analysis, we considered several classes of mitigations, and conducted more exploratory reviews of each. Those discussed include mitigations for (1) reducing transmission, such as personal protective equipment and encouraging improved hygiene, (2) reducing exposure by changing norms and targeted changes for high-risk or critical professions and activities, (3) reducing impact for those infected, and (4) increasing large scale resilience using disaster and infrastructure continuity planning.Some proposed mitigations are found to be of low marginal value. Other mitigations are likely to be valuable, but the concepts or applications are underdeveloped. In those cases, further research, resources, or preparation are valuable for mitigating both routine and extreme disease outbreak events. Still more areas of research are identified as having uncertain value based on specific but resolvable uncertainties. In both of the latter cases, there is no guarantee that mitigations identified as worthy of further consideration will be valuable, but the argument for further research is clear.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

Infections with multi-drug-resistant (MDR) pathogens in food-animals threaten public health and food security. However, the epidemiology and factors associated with MDR Escherichia coli on Ugandan farms are not well known. This study investigated the prevalence, resistance patterns and factors associated with MDR E. coli carriage on chicken farms. A total of 158 E. coli strains were isolated from 158 chicken farms. The disc diffusion method for susceptibility testing was performed. Clinical breakpoints were interpreted according to Clinical and Laboratory Standards Institute guidelines. MDR was defined as resistance to three or more classes of antimicrobials. MDR E. coli prevalence on chicken farms was 62.7% (95% CI: 55.0 – 70.3). High resistance was observed against ampicillin 79.8% (95% CI: 72.7–85.4), tetracycline 72.8% (95% CI: 65.2–79.2), cotrimoxazole 55.7% (95% CI: 47.8–63.3), and ciprofloxacin 38% (95% CI: 30.7–45.9). Farmers who were males (APR = 0.72, CI: 0.55, 0.93), and attained at least secondary education (APR=0.64, CI: 0.46, 0.88) and administration of recommended antibiotic doses (APR = 0.76, CI: 0.59–0.96) posed a lower risk of MDR E. coli carriage. Farms without footbaths posed a heighten risk (APR=1.48, CI: 1.16–1.88). MDR E. coli were highly prevalent on chicken farms. This study underscores the need for antimicrobial stewardship and improved infection prevention strategies on chicken farms.

Background: Biomarkers are essential for identification of individuals at high risk of mild cognitive impairment (MCI) for potential prevention of dementia. We investigated DNA methylation in the ApoE gene and plasmatic apolipoprotein E (ApoE) levels as MCI biomarkers in Colombian subjects with MCI and controls. Methods: 100 participants were included (71% women, average age, 70 yrs., range 43-91). MCI was diagnosed by neuropsychological testing, medical and social history, activities of daily living, cognitive symptoms and neuroimaging. Multivariate logistic regression models adjusted by age and gender were performed to examine the risk association of MCI with plasma ApoE and APOE methylation Results: MCI was diagnosed in 41 subjects (average age, 66.5±9.6 yrs.) and compared with 59 controls. Elevated plasma ApoE and APOE methylation of CpGs 165, 190, and 198 were risk factors for MCI (P<0.05). Higher CpG-227 methylation correlated with lower risk for MCI (P=0.002). Only CpG-227 was significantly correlated with plasmatic ApoE levels (correlation coefficient=-0.665; P=0.008). Conclusion: Differential APOE methylation and increased plasma ApoE levels were correlated with MCI. These epigenetic patterns can be used as potential biomarkers to identify early stages of MCI.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

(1) Background: Hepatitis B virus (HBV) viral load (VL) is useful in determining treatment eligibility, however, due to high costs associated with the test, hepatitis B e antigen (HBeAg) is recommended as a proxy for HBV VL in resource-limited settings. (2) Methods: We used 299 archived plasma samples with hepatitis B surface antigen (HBsAg), HBeAg, and HBV VL (cut-off of 20,000 IU/mL and 200,000 IU/mL) results from people living with human immunodeficiency virus (PLWH). HBeAg and HBV VL results were analyzed to evaluate the use of HBeAg to determine CHB treatment eligibility and qualification of HBV prevention of mother-to-child transmission (PMTCT) prophylaxis for the first time in Botswana. (3) Results: Approximately 70.8% and 87.5% of participants with HBeAg-positive serology had HBV viral loads ≥20,000 IU/mL and 200,000 IU/mL respectively. Using logistic regression, the odds of having a qualifying HBV VL for CHB treatment and PMTCT prophylaxis were respectively 55.5 and 110.4 times higher in participants with positive HBeAg serology indicating a statistically significant association between HBeAg status and HBV VL. (4) Conclusions: HBeAg detection may not always correlate with high HBV VL, warranting further research focusing on this association, and other biomarkers that correlate better with HBV VL.

Cardiovascular disease (CVD) is the leading cause of death worldwide. Cardiac rehabilitation (CR) has proven to be effective in reducing the rate of recurrence and disease as secondary prevention (evidence-based intervention) in patients who have suffered from myocardial infarction (MI). CR is a multidisciplinary path in which the patient is followed pharmacologically, from a psychological, nutritional, nursing and physiotherapy point of view. Post-MI patients present a reduction in the performance of the diaphragm muscle, the main inspiratory muscle, and this condition can become a risk factor for further relapses or for the onset of heart failure. Despite the solidity of the international guidelines for CR, the latter are lacking in specifically indicating an evaluation and training path regarding the inspiratory muscles in post-MI patients who have not undergone cardiac surgery. The article reviews the information on the adaptation of the diaphragm post-MI and highlights the need for clearer indications for a rehabilitation process that gives importance to the diaphragm.

Preeclampsia (PE) is associated with an increased risk of cardiovascular disease (CVD) in later life. Postpartum cardiovascular risk screening could identify patients who would benefit most from lifestyle interventions. However, there are no readily available methods to identify these high-risk women. We propose that placental lesions may be useful in this regard. Here, we sought to determine the association between placental lesions and lifetime CVD risk. Placentas from 85 PE women were evaluated for histopathological lesions. At 6 months postpartum, a lifetime cardiovascular risk score was calculated. Placental lesions were compared between CVD risk groups and the association was assessed using odds ratios. Multivariable logistic regression was used to develop prediction models for CVD risk with placental pathology. Placentas from high-risk women had more severe lesions of maternal vascular malperfusion (MVM) and resulted in a 3-fold increased risk of screening high-risk for CVD (OR 3.10[1.20-7.92]) compared to women without these lesions. MVM lesion severity was moderately predictive of high-risk screening (AUC 0.63[0.51,0.75]; sensitivity 71.8%[54.6,84.4]; specificity 54.7%[41.5,67.3]. When clinical parameters were added, the model’s predictive performance improved (AUC 0.73[0.62,0.84]; sensitivity 78.4%[65.4,87.5]; specificity 51.6%[34.8,68.0]. The results suggest that placenta pathology may provide a unique modality to identify women for cardiovascular screening.

Additive Manufacturing (AM) provides an opportunity to fundamentally redesign components previously limited by conventional manufacturing techniques. A new process for this workflow of design, manufacture by Powder Bed Fusion (PBF) and validation is presented, to which a case study of a crank for a high performance racing bicycle is applied. Topology optimisation generated conceptually ideal geometry from which a functional design was interpreted. Design for AM considerations were employed to reduce build time, material usage and post-processing labour. PBF was employed to manufacture the parts, and the build quality assessed using Computed Tomography (CT). Static and dynamic functional testing was performed and compared to a Finite Element Analysis (FEA). CT confirmed good build quality of tall, complex geometry with no significant geometrical deviation from CAD over 0.5 mm. Static testing proved performance close to current market leaders, although failure under fatigue occurred after just 2495 ± 125 cycles, the failure mechanism was consistent in both its form and location. These physical results were representative of those simulated, thus validating the FEA. This research demonstrates a complete workflow from design, manufacture, post-treatment and validation of a highly loaded PBF manufactured component, offering practitioners with a validated approach to the application of PBF.

To encourage proper waste management from electrical and electronic devices (e-waste), it is necessary to invest heavily in the development of recycling technologies. One way to improve the process is to automate separating the shredded parts of e-waste using a robot. This paper's literature review, utilizing the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) framework, showcases potential robotic technologies for e-waste separation. However, the intricate design of these devices can pose significant challenges in their implementation. Various legal, organizational, and sociological obstacles have left Serbia's e-waste management practice underdeveloped, resulting in an unsatisfactory recycling rate. In this paper we examined the possibility of using robots on the precise example of recycling refrigerators in a recycling center in Eastern Serbia, concluding that such a solution would have multiple positive effects, both on the employees and the working environment, on the operations of the recycling center itself, and on increasing the e-waste recycling rate in the country.

Deep learning techniques, such as convolutional neural networks (CNN), generative adversarial networks (GAN), and graph neural networks (GNN), have over the past decade changed the ac-curacy of prediction in many diverse fields. In recent years, the application of deep learning tech-niques in computer vision tasks in pathology demonstrated extraordinary potential in assisting clinicians, automating diagnosis, and reducing costs for patients. Formerly unknown pathologi-cal evidence, such as morphological features related to specific biomarkers, copy number varia-tions, and other molecular features, were also able to be captured by deep learning models. In this paper, we review popular deep learning methods and some recent publications about their appli-cations in pathology.

A convenient and efficient strategy for the preparation of 2-sulfonylindoles has been achieved through iodophor/H2O2-mediated 2-sulfonylation of indoles with readily available sulfonyl hydrazides in aqueous phase. Iodophor is commercially available and serves as the green catalyst and aqueous phase. A series of 2-sulfonylated products from indoles and N-methylpyrrole were synthesized in moderate yields in only 10 min. Control experiments were also conducted to reveal the mechanism. This method is environment friendly, easy to operate and suitable for a wide range of substrates.

This paper presents the design and analysis of a novel 3-degree-of-freedom (3-DOF) parallel ma-nipulator equipped with self-sensing Ni-Ti (Nitinol) actuators. The manipulator's architecture and mechanical design are elucidated, emphasizing the integration of Nitinol actuators. The self-sensing technique implemented in a previous work was extended to a 20 mm actuator length, and the actuator was used to design the 3 DOF manipulator. Kinematic analyses were conducted to eval-uate the manipulator's performance under various operating conditions. A dynamic model was implemented for the dynamic dimensioning of the actuators, which work synergistically with a bias spring. The manipulator was realized, and a control strategy was implemented. Experimental tests, although documenting some positioning accuracy issues, show the efficacy and potential applica-tions of the proposed manipulator in robotics and automation systems, highlighting the advantages of self-sensing Nitinol actuators in small parallel manipulator designs.

This review summarizes the most recent developments of research on protozoan parasite infections ac-quired through food and drinking water and is aimed at gathering updated knowledge on the risk factors, illnesses caused, and measures for prevention. Reports included dated from 2019 to the present and regarded recent outbreaks and cases of severe infec-tions, prevalence in different population segments and food handlers, and occurrence in food and drinking water. Cryptosporidium spp., Entamoeba histolytica, Giardia intestinalis, Trypanosoma cruzi and Toxoplasma gondii were the microorganisms most frequently involved in large outbreaks and/or severe infections, while Cyclospora cayetanensis was most frequently involved in single case reports. Cystoisospora belli was implied in severe infections in immunocompromised patients, while Blastocystis homi-nis, Sarcocystis spp., Dientamoeba fragilis, Endolimax nana and Pentatrichomonas hominis appeared to be less relevant for number of symptomatic infections and pathogenic potential. A progressive improvement in surveillance of protozoan infections and infection sources was highlighted, especially in developed countries. The apparent increase in cases was concomitant with the implementa-tion of reporting systems and the application of molecular diagnostic methods that represent valuable in-struments for establishing epidemiological links and preventing or limiting outbreaks. The pathogenic role and sources of infection should be better elucidated for some species.

Through the half-unit circle area computation using the integration of the corresponding curve power series representation, we deduce a slow converging positive infinite series to $\pi$. However, by studying the remainder of that series we establish sufficiently close inequalities with equivalent lower and upper bound terms allowing us to estimate, more precisely, how the series approaches $\pi$. We use the obtained inequalities to compute up to four-digit denominator, what are in this sense, the best rational numbers that can replace $\pi$. It turns out that the well-known convergents of the continued fraction of $\pi$, $22/7$ and $355/113$ called, respectively, Yuel\"{u} and Mil\"{u} in China are the only ones found. Thus we apply a similar process to find rational estimations to $\pi+e$ where $e$ is taken as the power series of the exponential function evaluated at $1$. For rational numbers with denominators less than $2000$, the convergent $920/157$ of the continued fraction of $\pi+e$ turns out to be the only rational number of this type.

Irregular female migration to Europe is a growing phenomenon, as more and more women are fleeing their countries of origin due to gender inequality and violence. During the migration process, women experience physical, psychological and social problems that affect their sex lives. The aim of our study is to describe and understand how irregular migrant wom-en living in humanitarian reception centers experience their sexuality at different stages of the migration process. This qualitative phenomenological study collected data through a sixteen in-depth interviews with irregular migrant women between January and February 2023. Data anal-ysis was carried out using ATLAS-ti 23.0 software, from which three themes were extracted: 1) The sexual reality of sub-Saharan women, 2) In search of a better life: take the risk or surrender, and 3) The migrant sexual revolution. The sexual reality of sub-Saharan women is subject to a complex normative order. The migratory process has severe consequences on migrant women's sex life. The sexual needs of irregular migrant women admitted to humanitarian reception cen-ters undergo a process of change that must be understood by healthcare providers in order to make improvements to care provision.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

Under one-health perspective and the worldwide antimicrobial resistance concern, we investigate extraintestinal pathogenic Escherichia coli (ExPEC), uropathogenic E. coli (UPEC), and multidrug resistant (MDR) E. coli from 197 isolates recovered from healthy dogs in Spain between 2013 and 2017. Ninety-one (46.2%) isolates were classified as ExPEC and/or UPEC including 50 clones, among which (i) four clones were dominant (B2-CH14-180-ST127, B2-CH52-14-ST141, B2-CH103-9-ST372 and F-CH4-58-ST64815) and (ii) 15 had been shown to be displayed by previously published isolates causing extraintestinal infections in humans. Twenty-eight (14.2%) isolates were classified as MDR, associated with B1, D and E phylogroups and included 24 clones, of which eight had also been identified among human isolates causing infections. We selected 23 ST372 strains, 21 healthy dogs faecal isolates and two human clinical isolates for whole genome sequencing and built a SNP-tree with these 23 genomes and 174 genomes (128 from canine strains and 46 from human strains) obtained from public databases. The analysis of these 197 genomes allowed to identify six clusters. Cluster 1 comprised 74.6% of the strain genomes that were mostly composed of canine strain genomes (P &lt; 0.00001). Clusters 4 and 6 also included canine strain genomes, while clusters 2, 3 and 5 were significantly associated with human strain genomes. All these findings suggest that dogs are reservoirs of ExPEC, UPEC and MDR E. coli isolates with zoonotic potential.

We propose a pricing formula for a defaultable zero-coupon bond with imperfect information under a regime-switching model using a structural form of credit risk modelling. While the value of the firm’s equity is observed continuously, we assume that the total value of the firm is only observed at discrete times, such as the dates of the release of the firm’s annual reports, or quarterly reports. This uncertainty about the true value of the firm results in credit spreads that do not approach zero as the debt approaches maturity, which is a problem with many structural models. The firm’s value is typically defined as its equity and debt; however, we consider the asset-to-equity ratio, an accounting ratio used to examine a firm’s financial well-being. A dependent regime-switching process models the components of this ratio, and the Markov chain represents the states of the economy. The main contribution is to study this problem when the dynamics of a firm’s assets have different parameters with regime changes.

Bangladesh's railway system mostly uses typical manual railway crossing technique or boom gates through its 2,955.53 km rail route all over the country. The accidents are frequently happening in the railway crossings due to not having obstacle detectable and quickly operating gate systems, and also for fewer safety measures in the railway crossing. Currently, there are very few automatic railway crossing systems (without obstacle detectors) available, however, all of them are dependent on the national power grid without a backup plan for any emergency cases. Bangladesh is still running a bit behind in the power generation of its consumption, hence it is not possible to have a continuous power supply at all times all over the countryside. We aim to design and develop a smart railway crossing system with an obstacle detector to prevent common types of accidents in the railway crossing points. We design to use two infrared (IR) sensors to operate the railway crossing systems which will be controlled by the Arduino Uno. This newly designed level crossing system will be run with the help of sustainable renewable energy which is cost-effective, eco-friendly, and apply under the national green energy policy towards achieving sustainable development in Bangladesh as a part of the global sustainable goal to face climate change challenges. We have summarized the simulated results of several renewable energy sources including a hybrid system and optimized the Levelized Cost of Energy (LCOE), and the payback periods.

Gastric cancer is a challenging public health concern worldwide and remains a leading cause of cancer-related mortality. The primary risk factor implicated in gastric cancer development is infection with Helicobacter pylori. H. pylori induces chronic inflammation affecting the gastric epithelium, which can lead to DNA damage and promotion of precancerous lesions. Disease manifestations associated with H. pylori are attributed to virulence factors with multiple activities and its capacity to subvert host immunity. One of the most significant H. pylori virulence determinants is the cagPAI gene cluster, which encodes a type IV secretion system and the CagA toxin. This secretion system allows H. pylori to inject the CagA oncoprotein into host cells, causing multiple cellular perturbations. Despite the high prevalence of H. pylori infection, only a small percentage of affected individuals develop significant clinical outcomes, while most remain asymptomatic. Therefore, understanding how H. pylori triggers carcinogenesis and its immune evasion mechanisms is critical in preventing gastric cancer and miti-gating the burden of this life-threatening disease. This review aims to provide an overview of our current under-standing of H. pylori infection, its association with gastric cancer and other gastric diseases, and how it subverts the host immune system to establish persistent infection.

Phytophthora cinnamomi is a devastating soil-borne plant pathogen. The primary source of P. cinnamomi infection is the soil, where the pathogen can persist for long periods. Effective prevention and management of this pathogen in tree crops require an early and reliable detection method. In this study, we develop a simple, fast, reliable, and sensitive method based on real-time quantitative PCR (qPCR) for P. cinnamomi detection and quantification directly in plant or soil samples. Primers were developed targeting the nuclear single-copy ras-related protein gene Ypt1, suitable for Phytophthora-specific PCR. The specificity of the assay was confirmed by testing it against genomic DNA from 50 isolates across 8 different Phytophthora clades, including very similar P. parvispora. The efficiency and reliability of the qPCR protocol were evaluated on challenging environmental samples, such as plant tissue of different host trees (walnut, chestnut, oak) and naturally infected soils in walnut orchards. The main outcome was the development of a qPCR method for the specific identification and quantification of P. cinnamomi in natural soil samples. Additionally, this study established a systematic and repeatable soil sampling method and developed an efficient soil DNA extraction technique to apply the developed qPCR in naturally infested soils of walnut orchards.