During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

An identification key to twenty-nine species of Porina known from the country is provided. In addition, new records of Porina interstes, P. nuculastrum, and P. rhaphidiophora are described from the protected rain forests in southern Vietnam. A detailed taxonomic account of each species is provided and supported by its ecology, distribution, and illustrations.

The increasing amount of data transmitted through digital broadcasting and communication channels requires efficient transmission methods that make the most of limited resources such as frequency, time, and power. The layered division multiplexing (LDM) system, which is adopted by the Advanced Television Systems Committee (ATSC) 3.0 standard, is considered one of a solution for achieving efficient transmission. Additionally, the layered time-division multiplexing (LTDM) and time layered division multiplexing (TLDM) systems have been developed as well. These layered transmission systems, utilizing multiple physical layer pipes (PLPs), offer a wide range of services including mobile and rooftop TV. To compare the efficiencies of different layered transmission systems, the article introduces the concept of normalized channel capacity. This measure allows for a fair comparison among the systems by taking into account the specific channel capacity requirements of each service. By summing the normalized channel capacities, a method is proposed to select the most efficient transmission system among the four systems: LDM, LTDM, TLDM, and time division multiplexing (TDM). The Lagrange multiplier method is employed to find the parameters that maximize the sum of the normalized channel capacities in these systems. Through simulations conducted with the determined parameters, it is demonstrated that the LDM system exhibits the highest efficiency among the four systems.

Metabolic surgery can promote comprehensive physiological improvements to alleviate metabolic disorders, particularly for patients with type 2 diabetes. Nevertheless, the therapeutic scope has been limited owing to unexpectedly inconsistent surgical outcomes. Therefore, this study to overcome these obstacles by determining the fundamental mechanism underlying the conflicting outcomes. The surgical anatomy, clinical course, and outcomes of various metabolic surgeries, including modified duodenal-jejunal bypass (DJB) procedures, were compared to understand the specific surgical patterns from different perspectives comprehensively. Patients in the nonobese group were exclusively included to prevent confounding effects from overweight patients with type 2 diabetes. Following intestinal anastomosis, the epithelial identity of the succeeding intestine was replaced by that of the proximal epithelium owing to altered crosstalk between the epithelium and opposing mesenchymal cells. Subsequent intestinal compensatory proliferation and rapid turnover rate accelerate the spread of the replaced epithelium. The main factors contributing to inconsistent outcomes of metabolic surgery are inadequate duodenal exclusion and inappropriate biliopancreatic limb length. Replacement of enteroendocrine cells during regeneration can lead to inconsistent outcomes in metabolic surgery. The type and density of enteroendocrine cells distributed at the terminal end of the proximal intestine play a significant role in diverse outcomes of metabolic surgery.

Metabolic surgery can promote integrated physiologic improvement to ameliorate metabolic illness, particularly type 2 diabetes. Nevertheless, the therapeutic scope has been limited by unexpectedly inconsistent surgical outcomes. Therefore, the purpose of this study is to overcome the obstacles by determining the core mechanism of conflicting results. The surgical anatomy, clinical course, and outcomes of various metabolic surgeries, including modified types of duodenal-jejunal bypass procedures, were compared to comprehend specific surgical patterns from distinctive perspectives. Patients in exclusively nonobese groups are subjected to avoid compounding by weight fluctuations. During intestinal anastomosis, the epithelial identity of the succeeding intestine is replaced by that of the proximal epithelium through altered crosstalk between the epithelium and opposing mesenchymal cells. The rapid turnover rate and compensatory proliferation of the succeeding intestine accelerate the propagation of the replaced epithelium. Propagation of replaced epithelium could provoke inconsistent outcomes of metabolic surgery. The major determinants of the conflicting results of metabolic surgery are inadequate duodenal exclusion and inappropriate length of the biliopancreatic limbs. The replaced enteroendocrine cells during regeneration provoke inconsistent outcomes of metabolic surgery. The critical factors are the type and density of enteroendocrine cells distributed at the terminal end of the preceding proximal intestine.

As symbionts of fungi and algae, lichens produce a variety of secondary products which pharmacological activities. This study aimed to investigate the anti-inflammatory activities of Heterodermia hypoleuca and its main compound, atraric acid. The results confirmed that atraric acid could regulating induced pro-inflammatory cytokine, nitric oxide, induced nitric oxide synthase and cyclooxygenase-2 expression by lipopolysaccharide (LPS)-stimulated RAW264.7 cells. Means while, atraric acid down-regulated expression of phosphorylated IκB, ERK and nuclear factor kappa B (NFκB) signaling pathway to exhibit anti-inflammatory effects in LPS-stimulated RAW264.7 cells. Based on these results, the anti-inflammatory effect of atraric acid during LPS-induced endotoxin shock in a mouse model was confirmed. In the atraric acid treated-group, cytokine production was decreased in the peritoneum and serum, and each organ damaged by LPS-stimulation was recovered. These results show that atraric acid has an anti-inflammatory effect and its molecular mechanism may be involved in the inactivation of the ERK/NFκB signaling pathway, demonstrating its value as a potential therapeutic for inflammatory diseases.

The RNA-binding protein Human antigen R (HuR) regulates stability, translation, and nucleus-to-cytoplasm shuttling of its target mRNAs. The protein has been progressively recognized as a relevant therapeutic target for several pathologies like cancer, neurodegeneration, as well as inflammation. Inhibitors of mRNA binding to HuR might thus be beneficial against a variety of diseases. Here we present the rational identification of structurally novel HuR inhibitors. In particular, by combining chemoinformatics approaches, high throughput virtual screening and RNA–protein pull-down assays, we show that the 4-(2-(2,4,6-trioxotetrahydropyrimidin-5(2H)-ylidene)hydrazineyl)benzoate ligand exhibits dose-dependent HuR inhibition in binding experiments. Importantly, the chemical scaffold is new with respect to the so-far known HuR inhibitors, opening up a new avenue for the design of pharmaceutical agents targeting this important protein.

3D printing is commonly used to create complex objects at a low cost. It has also been applied in the fabrication of metamaterials and metasurfaces, which alter the propagation path of electromagnetic waves. These structures have diverse applications, including enhancing beam direction, improving antenna gain and signal-to-noise ratio, and creating filters and reflectors. Metasurfaces are cheap to fabricate and their use is expected to boost antenna efficiency in 5G telecommunications and beyond. However, accurately characterizing their profile remains a significant challenge. This paper presents a low-cost fully automated 4-axis instrument for microwave metasurface charac-terization, overcoming limitations of manual methods and offering an efficient and accurate approach. This research represents a significant advancement in microwave metasurface characterization, enabling sophisticated techniques to advance wireless communication technolo-gies, as it is the case of the future 5G and millimeter-wave communication systems. The equipment has an approximate cost of $1550 USD and was able to characterize a metalens with a focal distance of 20 cm designed for signals at 30 GHz. It was possible to create 2D and 3D profiles of the intensity distribution focused by the metalens and extract parameters such as the gain (8.05 dB), 3dB depth of focus (11 cm) and full width at half maximum (2.17 cm). The comparison of the measurements with the diffraction calculations of the metalens showed a very good agreement between the in-tensity distributions and the parameters of the metalens.

As the incidence and prevalence of diabetes increases, intervention through dietary education is becoming more important for diabetes control. This systematic review aimed to confirm the ef-fect of dietary intervention education on diabetes control. The study subjects were type 2 diabet-ic patients, and the main outcome variable was glycosylated hemoglobin level (HbA1c). The target studies were randomized controlled trials. Thirty-six studies were included in the analysis, of which 33 were included in the meta-analysis. The effect size between the dietary education and general intervention, was -0.42 (n=5,639, MD=-0.42; 95% CI -0.53 to -0.31) and was signifi-cantly different (Z=7.73, P<.001). When subgroup analyses were performed following the appli-cation periods, intervention methods, and intervention contents, the mean differences in 4–6-month application, individual education, diet-exercise-psychosocial intervention were -0.51, (n=2,742, 95% CI -0.71 to -0.32), -0.63 (n=627, 95% CI -1.00 to -0.26), and -0.51 (n=3.244, 95% CI -0.71 to -0.32), respectively. Dietary education interventions provided for at least 3 months were highly effective in controlling blood sugar levels. Regarding the education method, individual-ized education was more effective, and for this, contact or non-contact education may be applied. Combining diet, exercise, and psychosocial intervention is more effective than diet education alone.

The treatment of peptides has played an important role in clinical practice since the discovery of insulin therapy in the 1920s. Over 60 peptide drugs are approved in the United States (US and other regional mar-kets, and peptides continue to undergo drug discovery steadily. Peptide research and development has lev-eraged a wider range of structures known from other plant sources, via pharmacology and medicinal molecular biology, beyond its conventional focus on individual endogenous peptides. We build a comprehensive database of peptides that have met scientific studies with more than 150 constantly evolving peptides. Here we provide a simple overview of the peptide-based drug therapy environment, comprising evolutionary points of view, structural properties, operational thresholds, and explanation of the therapeutic area.

The steering performance according to the steering angle control was tested by using the active steering bogie developed to reduce excessive wheels and rail wear and noise generated when the railway vehicle run in a curved section. As a result of the test of increasing the steering angle in accordance with the target steering angle in the 300m radius of curvature, the bogie is gradually aligned in the radial steering position, and when the control is carried out to 100% of the target steering angle, the bogie angles of the front and rear bogies appeared almost the same. As the steering angle increased, wheel lateral force and derailment coefficient also decreased. Therefore, the validity of the radial steering position control method applied in this paper was confirmed experimentally. This test results will be used for future research on active steering bogie commercialization.

Biosensors are smart devices that convert biochemical responses to electrical signals. Designing biosensor devices with high sensitivity and selectivity is of great interest because of their wide range of functional operations. However, the major obstacles in the practical application of biosensors are their binding affinity toward biomolecules and the conversion and amplification of the interaction to various signals such as electrical, optical, gravimetric, and electrochemical signals. Additionally, enhancement of sensitivity, limit of detection, time of response, reproducibility, and stability are considerable challenges when designing an efficient biosensor. In this regard, hybrid composites have high sensitivity, selectivity, thermal stability, and tunable electrical conductivities. The integration of phthalocyanines (Pcs) with conductive materials such as carbon nanomaterials or metal nanoparticles (MNPs) improves the electrochemical response, signal amplification, and stability of biosensors. This review explores recent advancements in hybrid Pcs for biomolecule detection. Herein, we discuss the synthetic strategies, material properties, working mechanisms, and integration methods for designing electrochemical biosensors. Finally, the challenges and future directions of hybrid Pc composites for biosensor applications are discussed.

In recent years, cancer therapy has witnessed significant advancements, with a focus on personalized and targeted treatment strategies. One promising approach involves the use of stimuli-responsive biomaterials for site-specific drug release. Among these biomaterials, pH, and redox-triggered polymer-nano composites have gained immense attention due to their ability to respond to the specific tumor microenvironment, enhancing therapeutic efficacy while reducing off-target effects. Cancer cells often exhibit anomalous biochemical properties, attributed to lower cytosolic pH (acidic) and elevated redox potential through the epitomized upregulation of undesired genes. Such biological process substantially imbalance the level ions (protons) and biological thiols glutathione (GHS) in the cytoplasm as well as in the subcellular organelles. Superfluous accumulation of ions and redox imbalance is associated with proliferation, invasion, and growth of tumor. Because of high surface area, deep tissue penetration capability, higher hydrophilicity, hydrophobic interior for drug/gene efficient loading, biocompatibility and site-specific targeting efficiency, functionalized polymer nanocomposites are superior to conventional small molecular materials. Paradoxically conventional methods of drug delivery aided therapeutics accompanied with inherent drug/genes are encapsulated in biocompatible carrier or suitable transfecting agents generally suffered with low bioavailability, uncontrolled drug release, low cellular penetration, cellular internalization, toxicity, and poor drug loading efficiency. To overcome these issues, recently various multifunctional nanomaterials were developed, based on synergistic stimuli responsive aided drug release in a specified cellular or subcellular system. High therapeutic efficacy, of nanoparticles (NPs) mainly associated with surface functionalization through biocompatible polymeric materials, site-specific targeting units accompanied with stimuli responsive components. Followed by therapeutically important drug or genetic materials were loaded into NPs either in covalent or non-covalent approach. Intriguingly, combined pH and redox dual stimuli based functional materials specially based on polymeric nanocomposites for cancer therapeutics scarcely reported. This article provides the recent progress in pH and redox-responsive polymer-nano composites for site-specific drug delivery in cancer therapy. It explores design principles, fabrication methods, mechanism of action, and prospects of these dual-stimuli responsive biomaterials.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

We report a new fabrication method for a fully stretchable supercapacitor based on single wall carbon nanotube (SWCNT)-coated electrospun rubber nanofibers as stretchable supercapacitor electrodes. The deposition conditions of SWCNT on hydrophobic rubber nanofibers are experimentally optimized to induce a uniform coating of SWCNT. For surfactant-assisted coating of SWCNT, both water contact angle and sheet resistance were the lowest compared to the cases with other surface treatment methods, indicating the most effective coating approach. The excellent electromechanical properties of this electrode under the stretching condition is demonstrated by the measurement of Young’s modulus and normalized sheet resistance. This superb tolerance of the electrode with respect to stretching results from i) high aspect ratios of both nanofiber templates and the SWCNT conductors, ii) highly elastic nature of rubbery nanofiber, and iii) strong adherence of SWCNT-coated nanofiber on the elastic ecoflex substrate. Electrochemical and electromechanical measurements on the stretchable supercapacitor devices reveal that the volumetric capacitance (15.2 F cm-3 at 0.021 A cm-3) of the unstretched state is maintained for strains of up to 40 %. At this level of strain, the capacitance after 1,000 charge/discharge cycles is not significantly reduced. The high stability of our stretchable device suggests potential future applications in various types of wearable energy storage devices.

In industrial settings, gears play a crucial role by assisting various machinery functions such as speed control, torque manipulation, and altering motion direction.The malfunction or failure of these gear components can have serious repercussions, resulting in production halts and financial losses. As a result, there is an increasing requirement to monitor the state of these components in order to avoid such issues from occurring. To address this need, research efforts have focused on early defect detection in gears in order to reduce the impact of possible failures. This study focused on analyzing vibration and thermal datasets from two extruder machine gearboxes using an autoencoder Long Short-Term Memory (LSTM) model. The major goal is to implement an outlier detection approach to detect and classify defects. The results of this study highlighted the extraordinary performance of the Autoencoder LSTM model, which achieved an impressive accuracy rate of 94.42% in recognizing malfunctioning gearboxes within the extruder machine system. Furthermore, the study used a thorough global metrics evaluation methodology to further test the model’s dependability and efficacy, consequently substantiating the proposed approach’s validity.

The degradation of Proton-exchange membrane fuel cell (PEMFC) gasket materials is crucial in electric vehicles as it can cause hazardous hydrogen fuel leaks, which are usually due to high temperatures, pressures, and hydrogen fuel exposure. Degradation of gasket materials in PEMFC presents a critical concern for electric vehicle safety due to potential hydrogen fuel leaks. This study utilizes finite element analysis (FEA) to assess the suitability of gasket materials for PEMFC applications, focusing on aging and tensile conditions. The dual degradation framework, incorporating contact pressure and von Mises stress, is employed to evaluate Liquid Silicon Rubber (LSR) and Ethylene Propylene Diene Monomer (EPDM) materials. Under aging techniques, the Yeoh model exhibits the least Mean Absolute Percentage Error (MAPE) and computational cost of 0.27 seconds, while the Ogden model records the highest computational cost of 0.89 seconds. In evaluating MAE, Root Mean Square Error (RMSE), and R-squared metrics, LSR and EPDM materials demonstrate respective averages of 0.25%, 0.275%, 0.945%, and 0.815%, 0.685%, 0.77%. Tensile testing (Uniaxial) reveals RMSE and MAE values of 0.30%, 0.40%, and 0.50%, 0.40%, respectively. FEA proves instrumental in identifying suitable gasket materials for PEMFC applications. LSR emerges as the superior choice, demonstrating enhanced FEA modelling performance under aging and tensile conditions. These findings contribute valuable insights to the design and development of improved gasket materials, bolstering the safety and reliability of electric vehicles.

Background: This study explored the effects of a virtual reality exercise program on overweight middle-aged women. Methods: This randomized controlled trial included women 4065 years of age with a body mass index (BMI) of 23 kg/m2 or more living in D city. The virtual reality environment was set up by attaching an IoT sensor to an indoor bicycle and linking it with a smartphone, enabling exercise in an immersive virtual reality through a head-mounted display. Results: In the virtual reality exercise group, the BMI was significantly decreased after the 8-week intervention compared with the baseline value (F=100.806, p<.001). The depression scores were significantly different among the three groups, with the intervention effect being more significant in the virtual reality exercise group than in the indoor bicycle exercise and con-trol groups (F=3.462, p<.001). Furthermore, the levels of exercise fun (F=12.373, p<.001) and exer-cise immersion (F=14.629, p<.001) were significantly higher in the virtual reality exercise group than in the indoor bicycle exercise and control groups. Conclusions: The virtual reality exercise program positively affected the BMI and the levels of depression, exercise fun, and exercise im-mersion in overweight middle-aged women. It is an effective home exercise program for obesity management in this population.

In the era of big data, feature engineering has proved its efficiency and importance in dimensionality reduction and useful information extraction from original features. Feature engineering can be expressed as dimensionality reduction and is divided into two types of methods such as feature selection and feature extraction. Each method has its pros and cons. There are a lot of studies to combine these methods. Sparse autoencoder (SAE) is a representative deep feature learning method that combines feature selection with feature extraction. However, existing SAEs do not consider the feature importance during training. It causes extracting irrelevant information. In this paper, we propose a parallel guiding sparse autoencoder (PGSAE) to guide the information by two parallel guiding layers and sparsity constraints. The parallel guiding layers keep the main distribution using Wasserstein distance which is a metric of distribution difference, and it suppresses the leverage of guiding features to prevent overfitting. We perform our experiments using four datasets that have different dimensionality and number of samples. The proposed PGSAE method produces a better classification performance compared to other dimensionality reduction methods.

The construction industry, characterized by its intricate network of stakeholders and diverse workforce, grapples with the challenge of managing information effectively. This study delves into this issue, recognizing the universal importance of safeguarding data, particularly amid rising concerns of unauthorized access and breaches. Aiming to harness the potential of blockchain technology to address these challenges, this study used a hypothetical biographical and safety data of construction workers and securely stored on a Hyperledger Fabric blockchain. Developed within the Amazon Web Services (AWS) cloud platform, this blockchain infrastructure emerged as a robust solution for enhancing data security and privacy. Anchored in the core principles of data security, the model emerges as a potent defender against the vulnerabilities of traditional data management systems. Beyond its immediate implications, this study exemplifies the marriage of blockchain technology and the construction sector, potentially reshaping workforce management, especially in high-risk projects, optimizing risk assessment, resource allocation, and safety measures to mitigate work-related injuries. Practical validation through transaction testing using Hyperledger Explorer validates the model's feasibility and operational effectiveness, serving as a blueprint for the industry's data management. Ultimately, this research not only showcases the promise of blockchain technology in addressing construction data security challenges but also underscores its practical applicability through comprehensive testing, heralding a new era of data management that harmonizes security and efficiency for stakeholders' benefit.

This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. It posits two identical deterministic worlds -- one comprising a human agent and the other a machine agent. These agents exhibit different information processing mechanisms despite their apparent sameness in a causal sense. Providing a conceptual modeling of their difference, this paper resolves what it calls “the vantage point problem” – namely, how to justify an omniscient perspective through which a determinist asserts determinism from within the supposedly deterministic universe.

Switched-mode power supplies (SMPS) often utilize electrolytic capacitors due to their substantial energy density and economical pricing. However, their ability to function at low temperatures is essential for dependable operation in several sectors, including telecommunications, automotive, and aerospace. This study includes an experimental evaluation of how well standard SMPS electrolytic capacitors operate at low temperatures. This paper investigates the suitability of standard electrolytic capacitors used in switched-mode power supplies (SMPS) for low-temperature applications. The experimental evaluation exposed the capacitors to temperatures ranging from - 5 ∘C to - 40 ∘C, assessing capacitance (Cp), impedance (Z), dissipation factor (DF), and equivalent series resistance (ESR) at each temperature. The capacitor’s time-domain electrical signals were analyzed using the Pearson correlation coefficient to extract discriminative features. These features were input into an Artificial Neural Network (ANN) for training and testing. Results indicated a significant impact of low temperatures on capacitor performance. Capacitance decreased with lower temperatures, while ESR and leakage current increased, affecting stability and efficiency. Impedance proved to be a valuable diagnostic tool for identifying potential capacitor failure, showing a 98.44% accuracy drop at - 5 degrees and 88.75% at the peak temperature, indicating proximity to the manufacturer’s specified limit. The study suggests further research and development to improve electrolytic capacitors’ performance in SMPS systems under cold conditions to enhance efficiency and reliability.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

The negative energy solutions of the Klein-Gordon and Dirac equations have been used to define the antiparticle with the positive energy from the Feynman - Stueckelberg interpretation in the standard model based on the 4-D Minkowski space with the relative time. The negative energy solutions of the Klein-Gordon and Dirac equations are used to define the antiparticles with the negative energy in the present 3-D quantized space model. Note that all the present results are based on the 4-D Euclidean space with the absolute time (t) and relative time (t_l). Then the particle with the positive energy and antiparticle with the negative energy have the 4-D P₄ = TCP = T_cP symmetry. The continuity equations are derived from the Klein-Gordon, Dirac and Schrodinger equations. The Klein-Gordon and Schrodinger equations with the potential barriers are solved. The Klein paradox is explained by using the pair production of the electron with the positive energy and positron with the negative energy under the P₄ = _TcP symmetry, The effective velocity ( c_eff=√2 " c " ) and effective energy ("Etl =" √2 E ) along the relative time axis (ctl) give the relative time momentum of "p_tl"=E_tl/c_eff =(√2 E)/(√2 c)=E/c=p_t=p_x. This indicates that the photons with the energy of E have the constant photon velocity of c and the constant photon momentum of "ptl"=E_tl/c_eff =(√2 E)/(√2 c)=E/c=p_t=p_x. For the negative energy particles, the space momentum directions are opposite to the particle velocity directions because the energy is negative. And the matter collapse to the photons at the very high particle velocity is discussed from the length expansion. It is, for the first time, proposed that the gamma ray burst is originated from the matter collapse to the photons near the black hole. Also, the wave function collapse is explained from the length expansion. The wave function collapse takes place when the measurement makes the particle velocity to be zero. It is concluded that the negative energy solutions of the Klein-Gordon and Dirac equations support the existence of the partner antimatter universe with the negative energy and negative time direction. Our matter universe has the positive energy and the positive time direction.

Large epidemiological studies show U-shaped relationships between high-density lipoprotein cholesterol (HDL-C) levels and all-cause mortality in individuals without atherosclerotic cardiovascular diseases (ASCVD). Association in those with ASCVD by sex is unclear. We examined the association between HDL-C levels and 10-year all-cause mortality in subjects (≥40 years of age) with ASCVD using the 2010 National Health Insurance Service and the National Death Registry of Korea. We categorized HDL-C levels into three groups (low: <40 mg/dL for males, <50 mg/dL for females; high: 40-90 mg/dL for males, 50-90 mg/dL for females; extremely high: >90 mg/dL) and 10 mg/dL intervals. We conducted a sex-stratified and adjusted Cox proportional hazards analysis. Out of 1,711,548 individuals (54% female, mean age 61.4 years), 10-year mortality was observed in 218,252 (12.8%). Males had a higher mortality rate than females (16.2% vs 9.8%; P<0.001). When adjusting for age, body mass index, LDL-cholesterol, triglycerides, hypertension, diabetes, smoking, and alcohol consumption, the low and extremely high HDL-C groups had significantly higher hazard ratios for 10-year mortality compared to the high HDL-C group in males [1.183 (1.166-1.199), 1.359 (1.288-1.434)] and in females [1.153 (1.138-1.169), 1.095 (1.029-1.167)]. The frequency distribution bars for the 10-year mortality rate showed sex-specific nadirs of 50-59 mg/dL in males and 70-79 mg/dL in females. In this ASCVD cohort, the extremely high HDL-C (>90 mg/dL) group had 35.9% and 9.5% higher 10-year mortality risk than the high HDL-C group for males and females, respectively. There was a slightly U-shaped relationship between baseline HDL-C levels and 10-year mortality rate, with earlier inflection in males than in females.

The properties of the charged dark matters are discussed in terms of the new three-dimensional quantized space model. Because of the graviton evaporations, the very small Coulomb’s constant (k(dd)) of 10 ⁻⁴⁸ k and large gravitation constant (G_N(dd)) of 10⁶ G_N for the charged dark matters at the present time are expected. The tentative values of G and k are used for the explanation purpose. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle. Also, the gravitation constant has been changed with increasing of the time because of the graviton evaporation. In the present work, the B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = 0 are explained as the good candidates of the dark matters. Also, the particle creation, dark matters and dark energy could be deeply associated with the changing gravitation constants (G). It is expected that the changing process of the gravitation constant between the matters from G_N(mm) ≈ 10³⁶ G_N to G_N(mm) = G_N happened mostly near the inflation period. Therefore, during most of the universe evolution the gravitation constant could be taken as G_N(mm) = G_N. And the effective charges and effective rest masses of the particles are defined in terms of the fixed Coulomb’s constant (k) and fixed gravitation constant (G_N). Then, the effective charge of the B1 dark matter with EC = −2/3 e is (EC)_eff = −2/3·10⁻²⁴ e. It is concluded that the photons, gravitons and dark matters are the first particles created since the big bang. The particles can be created from the decay of the matter universe and the pair production of the particle and anti-particle with decreasing of the gravitation constant (G_N(mm)). Also, the weak force, strong force and dark matter force bosons are created from the interactions of the elementary particles with the T fluctuations of the vacuum energy.

To enhance the overall reliability of the power system, engineers have redirected their focus toward health monitoring and early detection of faults in transformers. Among these faults, transformer core defects demand particular attention. While fault simulation using software has traditionally been the preferred approach, these methods suffer from data inaccuracies in real-world conditions. Consequently, conducting actual experimental setups with induced faults is imperative to investigate core issues. This study uses Hilbert Transform (HT) as a signal processing technique to extract crucial data characteristics, thereby enhancing the performance of the classifier model. The research involves analyzing electric current signals from a single-phase 1kVA transformer. A comparative assessment of our proposed model was conducted using raw data and Fast Fourier Transform (FFT), evaluating accuracy, precision, recall, F1-score, and computational time. The results demonstrate a significant improvement in all metrics for the classifier models, particularly the k-nearest neighbor (KNN) algorithm, which exhibited values of 83.89%, 84.39%, 83.89%, 83.79%, and 0.0156 seconds, respectively. Future work aims to extend this analysis under different loading conditions.

The spin magnetic moments and spin g factors (g_s = -2) of electron, muon and tau are explained based on the electric charges (EC) and lepton charges (LC) in terms of the three-dimensional quantized space model. The spin g factors of electron, muon and tau are g_s = -2 which is the sum of the EC g factor (g_EC = -1) and the LC g factor (g_LC = -1). The spin g factor (g_s = -2) of the electron is predicted by the Dirac’s equation. The orbit g factors of electron, muon and tau are g_L = g_EC = -1 from the EC g factor (g_EC = -1) without the contribution of the LC g factor (g_LC = -1). The spin g factors of the elementary fermions are calculated from the equation of g_s = g_EC + g_LC + g_CC where g_EC = EC/|EC|, g_LC = LC/|LC| and g_CC = CC/|CC|. For example, the spin g factors of the neutrinos and dark matters are g_s = -1. The spin g factors of the u and d quarks are g_s = 0 and g_s = -2, respectively. The g factor problem of neutrinos with the non-zero LC charges are solved by the LC Coulomb force of F_c(LC) ≈0. It is, for the first time, proposed that the binary motion (fluctuations) of the m_EC and m_LC masses for the electron, muon and tau leptons make the anomalous g factor. This binary motion could be originated from the virtual particle processes including the photons. Also, the weak force (beta) decay is closely related to the binary motion of the m_EC and m_LC for the electron, muon and tau leptons.

The properties of the dark matter, dark energy, graviton and photon are discussed in terms of the new three-dimensional quantized space model. Three new particles (bastons) with the electric charges (EC) are proposed as the dark matters. It is proposed that the EC, LC and CC charges are aligned along the time axes but not along the space axes. The photon is confined on its corresponding three-dimensional quantized space. However, the graviton can be evaporated into other three-dimensional quantized spaces. The rest mass of the electron neutrino (n_e) of 3.494·10⁻³ eV/c² is obtained from the experimental vacuum energy density in terms of quantum field theory (QFT). The rest mass and force range of the massive g(0,0,0) graviton with the Planck size are m_g = 3.1872·10⁻³¹ eV/c² and x_r = 3.0955·10²³ m = 10.0 Mpc, respectively, based on the experimental rest mass and rms charge radius of the proton. The possible diameter (10 Mpc) of the largest galaxy cluster is remarkably consistent with the gravitational force range (10 Mpc). Then, the diameter of the largest dark matter distribution related to the largest galaxy cluster is 9.2865·10²³ m = 30 Mpc equal to the force range of the massive g(0) graviton with the rest mass of 1.0624·10⁻³¹ eV/c². Because of the huge number (N) of the evaporated gravitons, the very small Coulomb’s constant of about 10⁻⁴⁸k and large gravitation constant of 10⁶G_N are expected for the charged dark matters. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = 0 for the proton-like particle. The proposed weak gravitational force between the dark matters and normal matters explains the observed dark matter distributions of the bullet cluster, Abell 1689 cluster and Abell 520 cluster. The transition from the galaxy without the dark matters to the galaxy with the dark matters are explained. Also, the accelerated space expansion is caused by the new space quanta created by the evaporated gravitons into the x1x2x3 space and repulsive electromagnetic force between dark matters corresponding to the dark energy. The decreasing coupling constant of the strong force, neutron lifetime anomaly and the pressure distribution inside the proton are explained by the unobservable proton and hadronization. And the rest mass of 1.4 TeV/c² is assigned to the Le particle with the EC charge of −2e. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. Also, the gravitation constant has been changing with the time because of the graviton evaporation.

Although ionizing radiation (IR) is widely used for therapeutic and research purposes, studies on low-dose ionizing radiation (LDIR) are limited compared with those on other IR approaches, such as high-dose gamma irradiation and ultraviolet irradiation. High-dose IR affects DNA damage response and nucleotide-protein crosslinking, among other processes; however, the molecular consequences of LDIR have been poorly investigated. Here, we developed a method to profile RNA species crosslinked to an RNA-binding protein, human antigen R (HuR), using LDIR and high-throughput RNA sequencing. The RNA fragments isolated via LDIR-crosslinking and immunoprecipitation sequencing were crosslinked to HuR and protected from RNase-mediated digestion. Upon crosslinking HuR to target mRNAs, such as PAX6, ZFP91, NR2F6, and CAND2, the transcripts degraded rapidly in human cell lines. Additionally, PAX6 and NR2F6 downregulation mediated the beneficial effects of LDIR on cell viability. Thus, our approach provides a method for investigating post-transcriptional gene regulation using LDIR.

The time symmetry of T_c = CT is redefined based on the 4-D Euclidean space. The time inversion symmetry of T_c = CT changes the signs of the charge (q) and absolute time (ct) of the particle. The P symmetry changes the signs of the space momenta and handedness of the particle. The T_c symmetry changes the signs of the time momentum (P_t=E/c) and charges. The handedness are classified as the left-handedness and right-handedness on the 3-D space. The charges (|q| = cDt) and energies (E= cDtDV) of the particles are originated from the upward warping (q>0) and downward warping (q<0) of the particles along the time axis. The evolution of our matter universe with P_t > 0 since the big bang can be interpreted based on the CTP symmetry with the partner antimatter universe with p_t < 0. The photon space is called as the vacuum space. Then the E and M waves are the space fluctuations, and the gravitational G wave is the time fluctuations. And the E, M and G fields are newly explained. The zero E and M fields of the photon space indicates that the photon space and gamma ray are the 2EM waves. The rest mass energy of the particle is the 4-D space volume of the warped photon space. In the present work, the quantum wave function is considered as the 4-D vector with the space wave function and time axis wave function in the 4-D Euclidean space. The warped photon space corresponds to the squared wave function which is the probability density. It is concluded that, in the quantum mechanics, the imaginary number concept is introduced in the quantum wave functions instead of the time axis component of the 4-D wave function vector. The left-handed neutrino puzzle is explained from the handedness partner relation with the right-handed dark matters. Finally, the modified Lorentz transformations derived in the 4-D Euclidean space are compared with the Lorentz transformations of the special and general relativity theories in the 4-D Minkowski space.

In the present work, the charged B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = k(lq) = 0 are explained as the good candidates of the dark matters. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. The missing neutrinos are newly explained by using the dark matters and lepton charge force. The neutrino excess anomaly of the MinibooNE data is explained by the B1 dark matter scattering within the Cherenkov detectors. And the rest masses of 1.4 TeV/c² and 42.7 GeV/c² are assigned to the Le particle and the B2 dark matter, respectively, from the cosmic ray observations. In the present work, the Q1 baryon decays are used to explain the anti-Helium cosmic ray events. Because of the graviton evaporation and photon confinement, the very small Coulomb’s constant (k(dd)) of 10^x-54k and gravitation constant (G_N(dd)) of 10^xG_N for the charged dark matters at the present time are proposed. The x value can have the positive, zero or negative value around zero. Therefore, F_c(mm) > F_g(dd) (?) F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

In the present work, the charged dark matters of B1, B2 and B3 bastons are explained as the right-handed partners of the left-handed neutrinos. The new Higgs mechanism of SU(2)_DM×SU(2)_Weak×SU(2)_Strong including electromagnetic and gravitational forces is applied. And the rest masses of the elementary particles depend on their charge configurations. The left-handed neutrinos have only the lepton charges (LC) and the right-handed dark matters have only the electric charges (EC). This explains the fact that the rest masses of the left-handed neutrinos are so small, and the rest masses of the right-handed dark matters are relatively very large. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. The missing neutrinos are newly explained by using the dark matters and lepton charge force. The neutrino excess anomaly of the MinibooNE data is explained by the B1 dark matter scattering within the Cherenkov detectors. The quark mixing and neutrino mixing are not required in the present model. It is shown that our matter universe and its partner antimatter universe can be created from the big bang in the point of view of time -, charge -, space -, and quantum state – symmetric universe evolution.

Origins of the time, mass, electric charges and magnetic monopoles are explained. The energies, electric charges and magnetic charges of the particles are defined as E = cDtDV and |q| = cDt = E/DV, and |q_m| = c²Dt, respectively, for the 3-D quantized spaces warped along the time axis direction of ct in the 4-D Euclidean space. The energy (or mass) and charges (or electric charges and magnetic charges) are the vectors along the time axis of ct in the 4-D Euclidean space. This new concept is closely connected to the wave function of the quantum mechanics. The electric charges, magnetic charges and energies have the property of the space direction independence. Magnetic monopoles (charges) are the force carrying bosons with the inside electric field time loop. Electric monopoles are the elementary fermions. Photon space fluctuations are explained with the quantized magnetic charges.

Space-time evolution of our universe is explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (E = cDtDV), charges and energy density (|q| = r = cDt) and absolute time (ct) are newly defined based on the 4-D Euclidean space. The photon flat space with the constant energy density of r = cDt_q is proposed as the dark energy (DE). The dark energy is separated into the n DE and photon DE which create the new photon spaces with the constant energy density of r = cDt_q. The v DE is from the n pair production by the CPT symmetry and the photon DE is from the photon space pair production by the T symmetry. The vacuum energy crisis and Hubble’s constant puzzle are explained by the photon space with the n DE and photon DE. The big bang and inflation of the primary black hole is connected to the accelerated space expansion and big collapse of the photon space through the universe evolution. The big bang from the nothing is the pair production of the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry. Our universe is the matter universe with the negative charges of electric charge (EC), lepton charge (LC) and color charge (CC). This first universe is made of dark matter -, lepton -, and quark - primary black holes with the huge negative charges which cause the Coulomb repulsive forces much bigger than the gravitational forces. The huge Coulomb forces induce the inflation of the primary black holes, that decay to the super-massive black holes and particles.

The relative force strengths of the Coulomb forces, gravitational forces, dark matter forces, weak forces and strong forces are compared for the dark matters, leptons, quarks, and normal matters (p and n baryons) in terms of the 3-D quantized space model. The quark confinement and asymptotic freedom are explained by the CC merging to the A(CC=-5)₃ state. The proton with the (EC,LC,CC) charge configuration of p(1,0,-5) is p(1,0) + A(CC=-5)₃. The A(CC=-5)₃ state has the 99.6% of the proton mass. The three quarks in p(1,0,-5) are asymptotically free in the EC and LC space of p(1,0) and are strongly confined in the CC space of A(CC=-5)₃. This means that the lepton beams in the deep inelastic scattering interact with three quarks in p(1,0) by the EC interaction and weak interaction. Then, the observed spin is the partial spin of p(1,0) which is 32.6 % of the total spin (1/2) of the proton. The A(CC=-5)₃ state has the 67.4 % of the proton spin. This explains the proton spin crisis. The EC charge distribution of the proton is the same to the EC charge distribution of p(1,0) which indicates that three quarks in p(1,0) are mostly near the proton surface. From the EC charge distribution of neutron, the 2 lepton system (called as the koron) of the koron is, for the first time, reported in the present work.

The origins of the stellar mass neutron black holes and supermassive dark matter black holes without the singularities are reported based on the 4-D Euclidean space. The neutron black holes with the mass of m_BH = 5 – 15 m_sun are made by the 6-quark merged states (N_6q) of two neutrons with the mass (m(N_6q) = 10 m(n)) of 9.4 GeV/c² that gives the black hole mass gap of m_BH = 3 – 5 m_sun. Also, the supermassive black holes with the mass of m_SMBH = 10⁶ – 10¹¹ msun are made by the merged 3-D states (J(B1B2B3)₃ particles) of the dark matters. The supermassive black hole at the center of the Milky way galaxy has the mass of mSMBH = 4.1 10⁶ m_sun that is consistent with m_SMBH = 2.08 - 6.23 10⁶ m_sun calculated from the 3-D states (J(B1B2B3)₃ particles) of the dark matters with the mass of m(J) = 1.95 10¹⁵ eV/c². In other words, this supports the existence of the B1, B2 and B3 dark matters with the proposed masses. The first dark matter black hole (primary black hole) was created at the big bang. This first dark matter black hole decayed to the supermassive dark matter black holes through the secondary dark matter black holes that are explained by the merged states of the J(B1B2B3)₃ particles. The universe evolution is closely connected to the decaying process of the dark matter black holes since the big bang. The dark matter cloud states are proposed at the intermediate mass black hole range of m_IMBH = 10² – 10⁵ msun. This can explain why the dark matter black holes are not observed at the intermediate mass black hole range of m_IMBH = 10² – 10⁵ m_sun.

Our matter universe is made up of four components of dark energy (DE), dark matters (DMs), leptons and quarks which are created from the decay of the primary black hole through the inflation after big bang. In the three-dimensional quantized space model, the sum (DER) of the dark energy (DE) and radiations (R) is the flat photon space and there are 39 particles of 3 dark matters, 9 leptons and 27 quarks. Generally speaking, the mass ratio of the quarks with the 27 particles is smallest and the mass ratio of the DER photon space with the 1 massless photon is largest. Therefore, the mass ratios of DER, DMs, leptons and quarks are inversely proportional to the particle numbers of DER, DMs, leptons and quarks as the first assumption. This simple rule is called as the universe mass ratio golden rule in Fig. 12. This simple rule is successfully applied to the observed mass ratios of the Planck and WMAP missions. The best particle number combination (1, 3, 9, 27) of the four components (DER, DMs, Leptons, Quarks) to explain the Planck 2018 and WMAP results is the same as the particle number combination (1, 3, 9, 27) of the 3-dimensional quantized space model. The calculated mass ratios of DER, DMs, leptons and quarks are 67.5 %, 22.5 %, 7.5 % and 2.5 %, respectively. And the calculated mass ratios of neutrinos and ordinary matters are 5.0 % and 5.0 %, respectively. The mass ratios of the dark energy (68.47(23) %) and matters (31.53(23) %) obtained from the Planck 2018 results are consistent with the calculated mass ratios of the DER (67.5 %) and matters (32.5 %). The mass ratio of the dark energy (72.1(15) %) obtained from the WMAP 9 year results is explained as the summed mass ratio (72.5 %) of DER (67.5 %) and neutrinos (5.0 %). The universe evolution including the super-massive black holes (SMBHs) is shown in Fig. 4. The accelerated space expansion of our universe requires the addition of the new dark energy. If this new dark energy is added, the mass ratio of the dark energy is a little bit increased. The difference (0.97 %) between the observed value (68.47(23) %) and calculated value (67.5 %) is explained by adding the new dark energy in Figs. 2, 4, 7, 8, 9, 10 and 11. The corrected mass ratios of DER, DMs, leptons and quarks are 68.47 %, 21.8286 %, 7.2762 % and 2.4254 %, respectively. The corrected mass ratios of the neutrinos (called as cosmic background neutrinos) and ordinary matters (OMs) are 4.8508 % and 4.8508 %, respectively. These corrected mass ratios can explain the mass ratios obtained from the WMAP and Planck missions. In other words, the mass ratios calculated from the best particle number combination support the elementary particles, dark matters and dark energy (photon space) proposed by the three-dimensional quantized space model based on the 10-D Euclidean space.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (mass), charges and absolute time are newly defined based on the 4-D Euclidean space. The photons and gravitons are understood as the 2-D space fluctuations along the space axes and 1-D time fluctuations along the time axis, respectively. This indicates that the electromagnetic (EM) and gravitational (G) waves can be unified into the so called gravityelectromagnetic (GEM) wave which has both space and time fluctuations. The photon with zero force fields is the 2EM wave because an EM wave corresponds to a charged fermion. The dark matter bosons, weak force bosons, strong force bosons are the 1-D time fluctuations which can be expressed by the G waves. This indicates that all five forces are unified by the GEM wave. It is called as the super unification theory in the present work. And the force carrying bosons and mesons are, for the first time, proposed as the possible candidates of the magnetic monopoles like the fermions and baryons are the electric monopoles. The signs of the magnetic charges quantized as q_m=cq are newly defined. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry.

Three-dimensional quantized space model is newly introduced. Quantum mechanics and relativity theory are explained in terms of the warped three-dimensional quantized spaces with the quantum time width (Dt=t_q). The energy is newly defined as the 4-dimensional space-time volume of E = cDtDV in the present work. It is shown that the wave function of the quantum mechanics is closely related to the warped quantized space shape with the space time-volume. The quantum entanglement and quantum wave function collapse are explained additionally. The special relativity theory is separated into the energy transition associated with the space-time shape transition of the matter and the momentum transition associated with the space-time location transition. Then, the quantum mechanics and the general relativity theory are about the 4-dimensional space-time volume and the 4-dimensional space-time distance, respectively.

The purpose of this study is to analyze the causes of cost variation in natural disaster prevention projects (NDPP) in Gyeongsangbuk-do and to develop effective cost and risk management strategies. The study collected data by conducting an online survey of 244 stakeholders. Binary logistic regression was used to analyze the impact of various variables on cost deviation, in-cluding project management risk (PMR), project costing and execution risk (PCER), project exe-cution strategy risk (PESR), construction project risk (CPR), project cost and schedule risk (PCSR), project management challenges (PMC), and construction project subcontractor and safety man-agement (CPSSM). The results showed that PMR (OR=3.744, 95% C.I. [1.657, 8.457]), PCER (OR=5.068, 95% C.I. [2.236, 11.484]), PESR (OR=3.447, 95% C.I. [1. 853, 6.413]), CPR (OR=2.292, 95% C.I. [1.020, 5.151]), PCSR (OR=4.817, 95% C.I. [2.250, 10.317]), PMC (OR=2.954, 95% C.I. [1.452, 6. 013]), and CPSSM (OR=2.419, 95% C.I. [1.297, 4.515]) had statistically significant effects on cost deviation. In particular, PMR, PCER, and PESR were identified as the main causes, and the effects of additional factors such as CPSSM were also important. The developed predictive model plays an important role in helping stakeholders of NDPP to manage risks in advance and take appro-priate preventive measures to ensure the success of the project. This study empirically supports the theoretical hypotheses of previous studies and provides a clear understanding of the causes of cost deviation in NDPP, which provides important insights for strategic decision-making and provides a new perspective on risk management.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (E=cDtDV), charges (|q|= cDt) and absolute time (ct) are newly defined based on the 4-D Euclidean space. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry. Our universe is the matter universe with the negative charges of electric charge (EC), lepton charge (LC) and color charge (CC). This first universe is made of three dark matter -, lepton -, and quark - primary black holes with the huge negative charges which cause the Coulomb repulsive forces much bigger than the gravitational forces. The huge Coulomb forces induce the inflation of the primary black holes, that decay to the super-massive black holes. The dark matter super-massive black holes surrounded by the normal matters and dark matters make the galaxies and galaxy clusters. The spiral arms of galaxies are closely related to the decay of the 3-D charged normal matter black holes to the 1-D charged normal matter black holes. The elementary leptons and quarks are created by the decay of the normal matter charged black holes, that is caused by the Coulomb forces much stronger than the gravitational forces. The Coulomb forces are very weak with the very small Coulomb constants (k₁(EC) = k_dd(EC) ) for the dark matters and very strong with the very big Coulomb constants (k₂(EC) = k_nn(EC)) for the normal matters because of the non-communication of the photons between the dark matters and normal matters. The photons are charge dependent and mass independent. But the dark matters and normal matters have the similar and very weak gravitational forces because of the communication of the gravitons between the dark matters and normal matters. The gravitons are charge independent and mass dependent. Note that the three kinds of charges (EC, LC and CC) and one kind of mass (m) exist in our matter universe. The dark matters, leptons and quarks have the charge configurations of (EC), (EC,LC) and (EC,LC,CC), respectively. Partial masses of elementary fermions are calculated, and the proton spin crisis is explained. The charged black holes are not the singularities.

The absolute time and relative time are defined in terms of the 4-D Euclidean space. Our universe is the 3-D x₁x₂x₃ quantized photon space which follows the absolute time simultaneity when the universe moves along the absolute time axis of ct. The length expansion of Dx = gDx₀ is derived under the condition of the absolute time (ct) simultaneity. From the similarity between this length expansion of Dx = gDx₀ and the energy increasing of E = gE₀, it is assumed that the energy is proportional to the particle size of Dx. The extension of this assumption to the 4-D Euclidean space gives the new definition that the particle energy (E) is the 4-D volume. Then, the particle mass energy is defined as E= mc² = cDtDV = gE₀. The masses of the elementary particles are originated from the 4-D warped volume of the photon space because the particle is the warped photon space with the velocity of v < c. Therefore, the Higgs boson concept in the standard model (SM) is not needed in the present 3-D quantized space model (TQSM). The scalar boson with the spin of zero, photon with the spin of 1 and graviton with the spin of 2 are the two-boson states. Therefore, the observed Higgs boson is reinterpreted as the two-boson state of the scalar boson with the spin of zero. The cosmic muon observation and twin paradox are explained by using the absolute time and relative time. The relative time is the observed time in the twin paradox and cosmic muon observation. In the twin paradox, a person who travels the long distance is more aged than a person on the earth in terms of the relative time ages because of the space and time conversion effect (STCE effect) of the moving space distance (x). But twins are in the same ages in terms of the absolute time without STCE effect. The fast-moving cosmic muon has the expanded half-life from the time expansion of the relative time. Also, the quantum entanglement and Pauli exclusion principle are explained. The quantum base of the photon space line connects two entangled particles. Two particles and quantum base system is fluctuated along the absolute time axis by the time clicking when one particle is measured. Another particle is instantly selected by the time clicking. This is called as the quantum entanglement. The photons which are the flat photon space with the constant speed of c along the space axis and absolute time axis have the 4-D photon velocity of c_eff = 2^0.5 c. Total 10-D Euclidean space including three 3-D quantized spaces and one absolute time axis is required for the electric charges (EC), lepton charges (CC) and color charges (CC) of the elementary particles. The 3-D photon space is very stiff along the absolute time (ct) axis and very soft along the space axes. The Coulomb force through the photons (2EM waves) of the space fluctuations is much stronger than the Gravitational force through the gravitons (G waves) of the time fluctuations between two electrons.

The 2020 revision of South Korea’s Personal Information Protection Act (PIPA) updated procedures for the use of medical data for research. The PIPA provision allowing “pseudonymized information” to be used without the consent of the data subject for scientific research introduced ambiguity regarding the applicability of the PIPA versus the Bioethics and Safety Act (BSA), which allows “anonymized information” to be used for research only after data-subject consent and IRB approval for human-subject research are obtained. The main points requiring clarification include the distinction between “human-subject” and “scientific” research, the definition of anonymization and pseudonymization, the requirements for data-subject consent, and the procedures for institutional review boards (IRBs) and data review boards (DRBs). After reviewing the legal concepts and processes, this article recommends clarification of the guidelines for the use of medical data in research by distinguishing the concept and, in the long run, categorizing medical data based on the degree of risk.

Coronavirus-infected diseases have posed great threats to human health. In past years, highly infectious coronavirus-induced diseases, including COVID-19, SARS, and MERS, have resulted in world-wide severe infections. Our literature annotations identified 110 chemical drugs and 26 antibodies effective against at least one human coronavirus infection in vitro or in vivo. Many of these drugs inhibit viral entry to cells and viral replication inside cells or modulate host immune responses. Many antimicrobial drugs, including antimalarial (e.g., chloroquine and mefloquine) and antifungal (e.g., terconazole and rapamycin) drugs as well as antibiotics (e.g., teicoplanin and azithromycin) were associated with anti-coronavirus activity. A few drugs, including remdesivir, chloroquine, favipiravir, and tocilizumab, have already been reported to be effective against SARS-CoV-2 infection in vitro or in vivo. After mapping our identified drugs to three ontologies ChEBI, NDF-RT, and DrON, many features such as roles and mechanisms of action (MoAs) of these drugs were identified and categorized. For example, out of 57 drugs with MoA annotations in NDF-RT, 47 have MoAs of different types of inhibitors and antagonists. A total of 29 anticoronaviral drugs are anticancer drugs with the antineoplastic role. Two clustering analyses, one based on ChEBI-based semantic similarity, the other based on drug chemical similarity, were performed to cluster 110 drugs to new categories. Moreover, differences in physicochemical properties among the drugs were found between those inhibiting viral entry and viral replication. A total of 163 host genes were identified as the known targets of 68 anti-coronavirus drugs, resulting in a network of 428 interactions among these drugs and targets. Chlorpromazine, dasatinib, and anisomycin are the hubs of the drug-target network with the highest number of connected target proteins. Many enriched pathways such as calcium signaling and neuroactive ligand-receptor interaction pathways were identified. These findings may be used to facilitate drug repurposing against COVID-19.

Three species of subfamily Cultrinae currently live in Korea, but Erythroculter erythropterus has been introduced into the Nakdonggang River and has taken over the habitat, reducing the habitat of Culter brevicauda. Only the endangered species C. brevicauda still lives in the Yeongsangang River, and it is necessary to be careful not to introduce E. erythropterus in the future. And Hemiculter eigenmanni is also found throughout the country. In order to effectively manage and conserve the species in its various habitats and against invasions, this study was initiated. The ultrastructure of the egg envelopes of three species of Cultrinae— E. erythropterus, C. brevicauda, and H. eigenmanni, inhabiting the Geumgang and Yeongsangang Rivers were observed. It was found that the zona radiata of the egg envelopes of all three species were divided into two layers–an outer and inner layer, with the outer surface having a non-structural form. This form is characteristic of fishes with muddy, stagnant habitats or spawning grounds. The number of pore canals on the surface of the egg envelopes was 83 for E. erythropterus, 75 for C. brevicauda, and 58 for H. eigenmanni per 10 ㎛2, and the thickness was 7.89±0.34 ㎛, 12.27±0.46 ㎛, and 7.42±0.24 ㎛, respectively. The shape of the micropyle demonstrated a funnel shape narrowing toward the inner diameter in all three species, and the size of the inner diameter was 6.62±0.29 (6.09~7.10) ㎛ in E. erythropterus, 4.19±0.39 (3.39~4.58) ㎛in C. brevicauda, and 3.98±0.46 (3.47~4.93) ㎛in H. eigenmanni. The differences between species were identified in the number of pore canals, thickness, and micropyle inner diameter of egg envelopes, which were species-specific. Our study revealed a morphological mechanism in the egg envelope that prevents the formation of interspecific hybrids, and these features can be taxonomic traits that clarify species names. It also provided useful data for the production (breeding) of the second generation in aquaculture.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

Knowledge-intensive business services (KIBS) are professional services that create new added value by creating, accumulating, and disseminating new knowledge. When it comes to conducting business involving new technology, KIBS play the roles of innovator, user, and producer of new technology that has led to technological innovation. This study aimed to determine the role of KIBS as a tool for innovation in a country’s economic system. Specifically, the degree and role of their impact on the Korean economy were analyzed and compared for the entire KIBS sector, T-KIBS (a new technology-based professional service), P-KIBS (a traditional professional service), and every subsector. For this purpose, the demand-inducement model, supply inducement model, and interlinkage effects method were applied using the 2019 input-output table published in 2022. The analysis showed that the indirect production inducement effect of the entire KIBS industry on other industries was 0.800 KRW, the indirect added value inducement effect was 0.330 KRW, and the supply disruption effect was 1.144 KRW. For T-KIBS, the indirect production inducement effect was 0.687 KRW, the indirect added value inducement effect was 0.272 KRW, and the supply disruption effect was 0.730 KRW. For P-KIBS, the indirect production inducement effect was 1.472 KRW, the indirect added value inducement effect was 0.646 KRW, and the supply disruption effect was 2.657 KRW. Finally, regarding the economic ripple effect of the KIBS subsector, legal and management support services and advertisements corresponding to P-KIBS showed higher figures than the T-KIBS subsectors in all sectors, including production inducement, the added value inducement effect, and the supply disruption effect. These results revealed that in the South Korean economic system, KIBS contribute to production and value addition across all industrial sectors. It is apparent that the absence of supply significantly disrupts other industries. Furthermore, production inducement effects are evenly distributed among all the KIBS subsectors in the secondary and tertiary sectors, while the value-added effects have a greater impact on the tertiary sector. In terms of the supply shortage effects, the secondary sector experiences a more significant impact. This underscores the crucial role of KIBS in sustaining and enhancing overall economic activity in South Korea. This study is significant in that it not only investigated KIBS as an industry group using the advantages provided by industry linkage analysis but also examined and compared detailed subsectors, thereby elaborately evaluating the influence relationship between KIBS and other industries. Therefore, the results presented in this study are expected to be useful for fostering the KIBS industrial sector and establishing economic innovation policies using KIBS.

Recently, smart mobility intelligent traffic services have become a critical task in Intelligent Transportation Systems (ITS). This involves not only the use of advanced sensors and controllers but also the ability to respond to real-time traffic situations at intersections, alleviate congestion, and generate policies to prevent traffic jams. DRL (Deep Reinforcement Learning) provides a natural framework for processing tasks. In DRL, each intersection can control itself and coordinate with neighbors to achieve optimal network-wide policies. However, comparing approaches remains a challenging task due to the existence of numerous possible configurations. This research performs a critical comparison of various traffic controllers found in the literature. It demonstrates that using a nonlinear approximator for coordination mechanisms and enhancing observability at each intersection are key performance drivers.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. The results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

As human activities of the countries in the East Asia have been remarkably expanding over recent decades, various problems in relation to ships, such as oil spill and many other coastal marine pollution, are continuously occurring in the coastal region. In order to conserve marine resources and prepare for possible ship accidents in advance, the need for efficient ship management is increasing over time. Multi-satellite, multi-sensor, multi-wavelength or multi-frequency observations make it possible to monitor a variety of vessels in the coastal region. This study presents the results of ship detection methodology applied to multi-spectral satellite images in the seas around Korean Peninsula based on optical, hyperspectral, and microwave remote sensing. To detect ships from hyperspectral images with a few hundreds of spectral channels, spectral matching algorithms are used to investigate similarity between the spectra and in-situ measurements. In the case of SAR (Synthetic Aperture Radar) images, the Constant False Alarm Rate (CFAR) algorithm is used to discriminate the vessels from backscattering coefficients of Sentinel-1 SAR and ALOS-2 PALSAR2 images. The present ship detection methods can be extensively utilized for optical, hyperspectral, and SAR images for comprehensive coastal management purposes toward perpetual sustainability in the future.

In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

The investigation by the integrated approach newly introduced for this study indicates that insulin resistance (IR) would develop first preferentially in the muscle tissue with a relatively low cell turnover and then progress in sequence to the subcutaneous adipose tissue, to the visceral adipose tissue, and to the liver with higher cell turnovers. Moreover, metabolic disruptions due to IR vary widely from tissue to tissue, contrary to the conventional notion that IR merely impairs glucose uptake in the whole body. This warrants that IR be divided better into four distinct tissue specific IRs: muscle insulin resistance (MIR), subcutaneous adipose insulin resistance (s-AIR), visceral adipose insulin resistance (v-AIR), and hepatic insulin resistance (HIR). Tissue-specific IRs developing in the order of MIR, s-AIR, v-AIR, and HIR – producing tissue specific metabolic disruptions – would amount to nothing but the whole body insulin resistance (WBIR) evolving in four distinctively insulin resistant stages. The four stage metabolic evolution from rapid weight gain to visceral obesity to rapid weight loss to full blown diabetes not only complies well with the natural development history of diabetes but also resolves most of the controversies regarding obesity or diabetes, including visceral obesity, obesity paradox, and dawn phenomenon that have long remained metabolic puzzles. In addition, the four-stage WBIR evolution model refutes the entrenched notion of the lipid-induced insulin resistance (LIIR) but supports instead the glycation-induced insulin resistance (GIIR) proposed in this study. A speculation is that the glycation reaction activated ever more with WBIR evolving may serve as the common thread connecting each other a cluster of disorders or diseases that are often collectively referred to as the metabolic syndrome, such as obesity, diabetes, cardio/cerebral vasculopathy, nephropathy, neuropathy, and retinopathy.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

This study focused on the precise detection and concordant analysis of circulating tumor cells (CTCs) to verify the usefulness of CTCs as promising clinical markers. CTCs are traditionally achieved using immune-fluorescence and morphological techniques. By combining two prostate cancer-specific genes (PSA and PSMA) and two epithelial-specific genes (EpCAM and KRT19), the CTC detection efficiency can be enhanced. The detection rates of localized prostate cancer (LPC), locally advanced prostate cancer (LAPC), metastatic hormone-sensitive prostate cancer (mHSPC), and metastatic castration-resistive prostate cancer (mCRPC) were 63.04 % (29/46), 70.59% (34/51), 94.34% (50/53), and 90% (126/140), respectively. Subsequent correlation analysis between the four genes, baseline PSA, and CTC count revealed that only the CTC count correlated with baseline PSA in the localized stages of prostate cancer, whereas all four genes were correlated with baseline PSA and CTC count in the metastatic stages of prostate cancer. The precise detection of CTCs using both numerical and transcriptomic analyses can improve the accuracy of biomarker investigations. This study provides valuable insights into the limitations of serum PSA testing and offers a promising alternative to diagnose and manage prostate cancer via the CTC number and specific genes for prostate cancer.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

This study focused on the development and implementation of an educational simulation program based on Korean Triage and Acuity Scale (KTAS) for nurses in emergency medical centers who completed KTAS training. We also examined its educational effects based on the evaluation of clinical decision-making ability, job satisfaction, and customer orientation. The study participants were 30 nurses in the emergency medical center of a general hospital. Data were collected from May 3 to 24, 2017, and analyzed using SPSS 22.0. There was a significant difference in the mean scores in clinical decision-making ability, job satisfaction, and customer orientation before and after simulation education. In other words, emergency nurses who received KTAS-based simulation education program improved their clinical decision making ability, job satisfaction, and customer orientation. Based on the results of this study, it is expected that it can be used for KTAS education, and it was found that simulation-based education is a useful learning method for triage nurses in emergency medical center.

The conserved MYST proteins form the largest family of histone acetyltransferases (HATs) that acetylate lysines within the N-terminal tails of histone, enabling active gene transcription. Here, we have investigated the biological and regulatory functions of the MYST family HAT Sas3 in the opportunistic human pathogenic fungus Aspergillus fumigatus using a series of genetic, biochemical, pathogenic, and transcriptomic analyses. The deletion of sas3 results in drastically reduced colony growth, asexual development, spore germination, response to stresses, and the fungal virulence. Genome-wide expression analyses have revealed that the sas3 mutant showed 2,402 significant differentially expressed genes; 1,147 up-regulated and 1,255 down-regulated. The representative up-regulated gene resulting from sas3 is hacA predicted to encode a bZIP transcription factor, whereas the UV-endonuclease UVE-1 was significantly down-regulated by sas3. Furthermore, our Western blot analyses suggest that Sas3 likely catalyzes acetylation of H3K9, K3K14, and H3K29 in A. fumigatus. In conclusion, Sas3 is associated with diverse biological processes and can be a potential target for controlling pathogenic fungi.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

Anesthetic management for pregnant suffering from airway pathology poses unique challenges. The presence of bilateral vocal cord granuloma adds further complexity to the management, as it can potentially cause airway compromise and respiratory distress. This case presents a pregnant patient with bilateral vocal cord granuloma who underwent anesthesia using high-flow nasal cannula (HFNC) oxygenation and oxygen reserve index (ORi) monitoring. A 33-year-old pregnant woman, who had undergone intubation six month ago, experienced hoarseness and was ultimately diagnosed with bilateral granuloma. Due to the significant airway obstruction, neither intubation nor ventilation was feasible, thereby requiring a surgical intervention. Before the surgical removal, the patient’s oxygenation was ensured using HFNC oxygenation. After confirming sufficient oxygenation of the patient with ORi of 0.38, the operation commenced and as it lasted approximately 3 minutes, the patient was able to tolerate the brief period without additional oxygen supply. Post-surgical excision, mask bagging and HFNC oxygenation was resumed, driving ORi to 0.39, then the operation was resumed. Throughout the procedure, SpO2 remained above 98. The combination of HFNC and ORi ensured adequate oxygenation and allowed for early detection of hypoxemia during the procedure. This approach may be a good option for managing granuloma.

Characters are one of the most important elements in composing digital animation. The appear-ance and voice of a character should be designed to express the personality and values of the character. However, it is not easy for animation producers to harmoniously match the appear-ance and voice of a character. Advances in deep learning technology have made it possible to overcome this limitation. To achieve this, firstly, an audio-visual dataset of characters is required. In this study, we construct and verify a Korean audio-visual dataset consisting of frontal face im-ages of various characters and short voice clips. We developed an application that can automati-cally extract the frontal face image and a short voice clip of a character by collecting videos up-loaded to YouTube. Through this, a dataset consisting of a total of 1,522 face images and a total of 7,999 seconds of voice clips was built based on 490 characters. Furthermore, we automatically la-bel characters by gender and age to validate the dataset. The dataset built in this study is expected to be used in various deep learning fields, such as classification, generative adversarial networks, and speech synthesis.

Aims TRAIL is a promising anticancer agent that has the potential to sensitize a wide variety of cancer or transformed cells by inducing apoptosis. However, resistance to TRAIL is a growing concern. Current manuscript aimed to employing combination treatment to investigate resveratrol induced TRAIL sensitization in NSCLC. Method A549 and HCC-15 cells were used in experimental design. Cell viability was determined by morphological image, crystal violet staining and MTT assay. Apoptosis was evaluated by LDH assay, Annexin V and DAPI staining. Autophagy and apoptosis indicator protein were examined by western blotting. TEM and puncta assay were carried out to evaluate the autophagy. MTP and ROS activity were evaluated by JC-1 and H₂DCFDA staining. Findings Resveratrol is a polyphenolic compound capable of activation of tumor suppressor p53 and its pro-apoptotic modulator PUMA. Herein, we showed the p53-independent apoptosis by decrease the expression of phosphorylated Akt-mediated suppression of NF-κB that is also substantiated with the downregulation of anti-apoptotic factors Bcl-2 and Bcl-xl in NSCLC, resulting in an attenuation of TRAIL resistance in combined treatment. Furthermore, apoptosis was induced in TRAIL-resistant lung cancer cells with a co-treatment of resveratrol and TRAIL assessed by the loss of MMP, ROS generations which resulting the translocation of cytochrome c from the mitochondria into the cytosol due to mitochondrial dysfunction. Moreover, autophagy flux was not affected by resveratrol-induced TRAIL-mediated apoptosis in NSCLC. Significance Overall, targeting the NF-κB (p65) pathway via resveratrol attenuates TRAIL resistance and induces TRAIL-mediated apoptosis which could be the effective TRAIL-based cancer therapy regimen.

To identify gender- and age-related associations between adult dental checkups and unmet dental care needs, we analyzed data of 14,000 participants, ages ≥ 19, from the 7th Korea National Health and Nutrition Examination Survey (2016–2018) (KNHANES VII). Data was collected via self-report questionnaires and interviews. Complex sample chi-square test and multiple logistic regression analysis indicated 31.7% of participants had unmet dental care needs; in the prior 12months, 67.1% had not utilized dental services, and 43.3% had not received dental checkups. Odds ratios (ORs) for dental checkups and unmet dental needs were 8.87 (CI:7.80–10.09, p < 0.001) for those who used dental services and 1.28 (CI: 1.13–1.44, p < 0.001) for those who had not. Significant age-dependent associations between those not receiving dental checkups and the rate of unmet dental care include men and women aged 50–59 years (OR: 1.77; CI = 1.22–2.58 and OR: 1.43; CI: 1.02–2.02; p = 0.040, respectively) and women ≥ 70 years (OR = 1.79, CI = 1.20–2.66, p = 0.004). Reducing unmet dental care needs requires greater public health promotion and education regarding regular dental checkups; additional practical strategies could enhance dental checkup compliance.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

Multidrug resistant (MDR) bacteria have become a severe problem for public health. Developing new antibiotics for MDR bacteria is difficult, from inception to the clinically approved stage. Here, we have used a new approach; we have modified the antibiotic, ciprofloxacin (CFX), with triphenylphosphonium (TPP, PPh3) moiety via ester- (CFX-ester-PPh3) and amide-coupling (CFX-ester-PPh3), to target bacterial membranes. In this study, we have evaluated the antibacterial activities of CFX and its derivatives against 16 species of bacteria, including MDR bacteria, using minimum inhibitory concentration (MIC) assay, morphological monitoring, and expression of resistance-related genes. TPP-conjugated CFX, CFX-ester-PPh3 and CFX-amide-PPh3 showed significantly improved antibacterial activity against Gram-positive bacteria, Staphylococcus aureus, including MDR S. aureus (MRSA) strains. The MRSA ST5 5016 strain showed high antibacterial activity, with an MIC values of 11.12 µg/mL for CFX-ester-PPh3 and 2.78 µg/mL for CFX-amide-PPh3. The CFX derivatives inhibited biofilm formation in MRSA by more than 74.9% of CFX-amide-PPh3. In the sub-MIC, CFX derivates induced significant morphological changes in MRSA, including irregular deformation and membrane disruption, accompanied by a decrease in the level of resistance-related gene expression. With these promising results, this method is very likely to combat MDR bacteria, through a simple TPP moiety modification of known antibiotics, which can be readily prepared at clinical sites.

Abstract: (1) Background: existing treatment methods for neglect are concentrated on egocentric neglect and lead to various problems, such as cost/space constraints and portability. Therefore, this study seeks to determine how treatment (a.k.a., Twins Therapy, TT) can improve an existing problem in relation to neglect in stroke patients; (2) Method: The research design was a pre-post test control group design and both groups maintained existing rehabilitation treatment and added TT intervention only to the experimental group. TT intervention was conducted for a total of 20 sessions (1 session 30 min/day, 5 days/week for 4 weeks); (3) Result: as a result of comparison be-fore and after the TT intervention, there was no significant difference in MFT and MBI items (p>.05). However, the score and execution time of the Apple Cancellation Test showed significant reduction only in the experimental group (p<.05); (4) Conclusion: as a result of the study, TT im-proved not only egocentric neglect, but also allocentric neglect symptoms in stroke patients

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

There are two major proposed forms of dark energy: the cosmological constant and the quintessence scalar field. However, the former has the cosmological constant problem and the latter does not have observational evidence to support the theory. In this paper, we propose a dark energy paradigm to solve the cosmological constant problem and to predict lepton masses as evidence. The dark energy paradigm is a unified dark sector that is based on Planck's dimensional analysis, Lambda CDM, energy conservation, and force equilibrium. We find that dark energy can vary from the cosmological constant to the Planck scale. We find that the predicted values of lepton masses based on the dark energy paradigm agree with the observed values to 1% (or within error ranges).

Recently, e-commerce companies have been adopting and continuously enhancing personalized product recommendation systems, and there is active research in this field within academia. However, personalized product recommendations in offline retail stores have not yielded significant outcomes thus far. Especially for small-format offline retail businesses like convenience stores, where customer information might be limited, providing personalized product recommendations poses even greater challenges. To address this issue, this study aimed to find a solution by shifting the perspective on recommendation methods and altering the target of recommendations in existing personalized recommendation models. In this study, recommending products that customers need in an offline store was defined as suggesting products that should be introduced and displayed within the store. In other words, the recommendation focus shifted from individuals to the stores themselves. This recommendation system proposes products that individual stores have not yet introduced but are anticipated to be purchased by customers among the products managed by the headquarters. Building upon this, we devised a store-based product recommendation system. The widely used user-based collaborative filtering model, a common technique in existing recommendation systems, was adapted into a store-based collaborative filtering model. Furthermore, various rules and logic pertinent to store operations and business considerations for convenience stores were integrated to implement this store product recommendation system. The accuracy and effectiveness of the system were demonstrated through its application in actual convenience stores. Results from the pilot implementation of the system showed that 88% of the newly recommended products in individual stores were sold based on one week of sales data, and the sales revenue was 1.75 times higher than the average sales revenue of those products across the entire company. Survey results on business owners' satisfaction yielded a score of 4.2 out of 5, indicating a high level of contentment. Additional observed effects included the expansion of product range and reduction in order lead times. However, 12% of the total recommended SKUs did not sell within one week, and 34% of the SKUs did not meet the overall average sales quantity. This research holds significance in extending the scope of personalized recommendation studies from primarily online platforms to offline retail businesses like convenience stores. It provides tangible methodologies and outcomes that can be implemented in real-world settings through the construction and validation of an actual system. The study also suggests avenues for future research to address some of the identified limitations.

Background: Diffuse large B-cell lymphoma is the most common type of non-Hodgkin's lymphoma. Due to the variety of clinical manifestations, accurate diagnosis can be challenging. Here, we present a case of DLBCL that was initially misdiagnosed as a hematoma, highlighting the importance of considering malignancy in the setting of non-responsive soft tissue swelling. Methods: A 76-year-old man presented to the emergency department with right periorbital swelling and ecchymosis. The symptoms first appeared after an injury and did not resolve spontaneously. The patient was taking warfarin for atrial fibrillation. A facial bone CT revealed a large irregular homogeneous mass. An extraconal hematoma was suspected based on clinical history and radiologic findings. Incision and drainage were performed, resulting in evacuation of old blood. Despite continued drainage, the patient's symptoms worsened. A comparison with the previous CT revealed an increase in the size of the lesion. As a result, a surgical excisional biopsy was performed. Results: Biopsy of the mass showed a diffuse infiltrate of lymphocytes around the tissue. The diagnosis of diffuse large B-cell lymphoma was confirmed pathologically. The patient was referred to hematology for further management. Conclusions: DLBCL is a rare disease associated with a poor prognosis. Due to the previous injury and the use of anticoagulants, the patient was initially misdiagnosed as having a hematoma. This delayed the prompt diagnosis and affected the timing of treatment initiation. We must be aware that a malignant mass is a potential cause of unresponsive soft tissue swelling.

The aim of this study is to propose and validate the state space mode decomposition technique for precise mode separation of non-classical damping systems and closely distributed modal systems. To assess the reliability and applicability of this technique, a 40-story building with a tuned mass damper is investigated, and acceleration responses measured by the building's health monitoring system are used for the verification of the technique. The mode separation results reveal that the separated modal power spectrum becomes distorted at neighboring natural frequency ranges when the performance index only considers the concentration of power spectral energy at the target natural frequency. However, by introducing an augmented performance index that includes a constraint condition to account for distortion, more accurate mode decomposition can be achieved.

Mobile elevating work platforms (MEWPs) consist of a work platform, extending structure, and chassis, and are used to move persons to working positions. MEWPs are useful but are composed of pieces of equipment, and accidents do occur owing to equipment defects. Among these defects, accidents caused by the fracture of bolts fixed to the extension structure and swing system are increasing. This paper presents a failure analysis of the fixing bolts of MEWP. Standard procedure for failure analysis was employed in this investigation. Visual inspection, chemical analysis, tensile strength measurement, and finite element analysis (FEA) were used to analyze the failure of the fixing bolts. Using this failure analysis approach, we found the root cause of failure and proposed a means for solving this type of failure in the future. First, the chemical composition of the fixing bolt is obtained by a spectroscopy chemical analysis method, which determined that the chemical composition matched the required standard. The tensile test showed that the tensile and yield strengths were within the required capacity. The stress analysis was carried out at five different boom angles, and it was determined that the fixing bolt of MEWP can withstand the loads at all the boom angles. The outcomes of the fatigue analysis revealed that the fixing bolt fails before reaching the design requirements. The results of the fatigue analysis showed primarily that the failure of the fixing bolt was due to fatigue. A visual inspection of the fractured section of the fixing bolt also confirmed the fatigue failure. We propose a method to prevent failure of the fixing bolt of the MEWP from four different standpoints: the manufacturer, safety certification authority, safety inspection agency, and owner.

Liver receptor homolog-1 (LRH-1) has emerged as a regulator of hepatic glucose, bile acid, and mitochondrial metabolism. However, the functional mechanism underlying the effect of LRH-1 on lipid mobilization has not been addressed. This study investigated the regulatory function of LRH-1 in lipid metabolism during fasting. The wild-type (WT) and LRH-1 liver-specific knockout (LKO) mice were either fed or fasted for 24 h, and the liver and serum were isolated. During fasting, the LRH-1 LKO mice showed greater accumulation of triglycerides in the liver compared to that in WT mice. Interestingly, LRH-1 LKO liver decreased the perilipin 5 (PLIN5) expression and genes involved in β-oxidation. Additionally, the LRH-1 agonist dialauroylphosphatidylcholine also enhanced PLIN5 expression in human cultured HepG2 cells. To identify new target genes of LRH-1, these findings directed to analyze the PLIN5 promoter sequence, which revealed −1620/−1614 to be a putative binding site for LRH-1. This was confirmed by promoter activity and chromatin immuno-precipitation assays. Moreover, fasted WT primary hepatocytes showed increased co-localization of PLIN5 in lipid droplets (LDs) compared to that in fasted LRH-1 LKO primary hepatocytes. Overall, these findings suggest that PLIN5 might be a novel target of LRH-1 to mobilize LDs and manage the cellular needs.

To address the challenges of climate change and food security, the establishment of smart farm complexes is necessary. While there have been numerous studies on the productivity and environmental control of individual greenhouses, research on greenhouse complexes is considerably limited. Conducting environmental studies during the design phase of these complexes poses financial constraints and practical limitations in terms of on-site experiments. To identify potential issues that may arise when developing large-scale greenhouse complexes, it is possible to utilize modeling techniques using Computational Fluid Dynamics (CFD) to assess environmental concerns and location issues before constructing the facilities. Consequently, simulating large-scale CFD models that incorporate multiple greenhouses and atmospheric conditions simultaneously presents significant numerical challenges. The objective of this study was to develop a guideline for verifying CFD models for a large-scale Venlo greenhouse, where acquiring field data before construction is not feasible for designing a greenhouse complex. The verification processes of the CFD models were conducted using 2D and 3D iterative simulations of a 2-hectare greenhouse model, using the improved Grid Independence Test (GIT) and wall Y+ approaches. Subsequently, the aerodynamic characteristics were analyzed in a 3D greenhouse model to access its performance when the wind direction was 90° in summer season. The findings revealed that a grid resolution of 0.8 meters and a first layer height of 0.04 meters were suitable for developing large-scale greenhouse models, resulting in a low Root Mean Square Error (RMSE) of 3.9% and a high coefficient of determination (R2) of 0.968. This process led to a significant reduction of 38% in the number of grid cells. These results will serve as design standards for large-scale greenhouses.

Autophagy, an alternative cell death mechanism, is also termed programmed cell death type II. Autophagy in cancer treatment needs to be regulated. In our study, autophagy inhibition by desipramine or the autophagy inhibitor chloroquine (CQ) enhanced tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) receptor-2 [death receptor (DR5)] expression and subsequently TRAIL-induced apoptosis in TRAIL-resistant A549 lung cancer cells. Genetic inhibition of DR5 substantially reduced desipramine-enhanced TRAIL-mediated apoptosis, proving that DR5 was required to increase TRAIL sensitivity in TRAIL-resistant cancer cells. Desipramine treatment upregulated p62 expression and promoted conversion of light chain 3 (LC3)-I to its lipid-conjugated form, LC3-II, indicating that autophagy inhibition occurred at the final stages of autophagic flux. Transmission electron microscopy analysis showed the presence of condensed autophagosomes, which resulted from the late stages of autophagy inhibition by desipramine. TRAIL, in combination with desipramine or CQ, augmented the expression of apoptosis-related proteins cleaved caspase-8 and cleaved caspase-3. Our results contributed to the understanding of the mechanism underlying the synergistic anti-cancer effect of desipramine and TRAIL and presented a novel mechanism of DR5 upregulation. These findings demonstrated that autophagic flux inhibition by desipramine potentiated TRAIL-induced apoptosis, suggesting that appropriate regulation of autophagy is required for sensitizing TRAIL-resistant cancer cells to TRAIL-mediated apoptosis.

Due to advances in power electronics technology and the evolution of automation devices, the number of electrical devices that are sensitive to power quality is rapidly increasing, and for this reason, users are increasing their demand for high quality. To meet power quality demands, many power conversion devices are used, including dynamic voltage restorers (DVRs). DVRs are rec-ognized as devices that can effectively manage problems such as voltage segment, swells, and harmonics. DVR control requires many samples for harmonic compensation, which has the dis-advantage of being complicated to implement due to fast digital signal processing computation and the application of the cyclic discrete Fourier transform. In this paper, a high-precision DVR system configuration is proposed that compensates for harmonics using a periodically equivalent time-interval sampling technique and a novel circular structured memory filter. The proposed circular structured multi-pointer memory filter is an effective filter algorithm for high-precision input voltage measurement because it can remove noise and compensate for the delay of the phase angle of the filter in voltage measurement. A simulation and DVR prototype system was built, and the feasibility and effectiveness of the phase angle multi-filter voltage detection method and the compensation method were verified by experiments.

The phenolics concentrations of rapeseed are important because they are antinutritional com-pound or directly positive related to antioxidant actives. In this study, single nucleotide poly-morphisms (SNPs) identified from genotyping-by-sequencing (GBS), and genome-wide associa-tion study of phenolic contents were investigated in 95 rapeseed mutant lines derived from gamma rays and their original cultivar. A total of 3,196,318 SNPs were detected, identifying a set of 70,208 union SNPs used to perform association studies. Six phenolics and glucosinolate (pro-goitrin) were identified, sinapine was the major phenolic compound (91.2–99.2%) in all geno-types. The association study was conducted for six phenolic compounds, progoitrin, total sinap-ine content (TSC), total phenolic content (TPC) and seed yield. The association study identified 241 SNPs that were significantly associated with six phenolic compounds, progoitrin, TSC and TPC. Based on the detected SNP markers, BnaA06g31740D, a gene associated progoitrin, BnaC-nng39930D, a gene associated trans-sinapine 1, BnaA07g31720D, a gene associated trans-sinapine 2, BnaC03g31950D and BnaA06g09180D, a gene associated TSC, and BnaAnng27700D, a gene associ-ated TPC, were selected as candidate genes. The SNP makers associated major phenolic com-pounds identified and could be used as targets for breeding programs aimed at improving anti-oxidant contents and reducing antinutritional components.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

The weakness of the dispersion-managed link combined with optical phase conjugation to compensate for optical signal distortion caused by chromatic dispersion and nonlinear Kerr effect of standard single mode fiber is its limited structural flexibility. We propose dispersion map that can simultaneously compensate for the distorted wavelength division multiplexed signal while increasing the configurational flexibility. Each residual dispersion per span (RDPS) in the former half of the proposed link is randomly determined, and in the latter half, the arrangement order of RDPS is the same as or inverted in the former half. We confirm that the dispersion maps in which the RDPS distribution pattern in the latter half is opposite to the arrangement order in the former half are more effective in compensation, and rather, the compensation effect is better than in the dispersion map of the conventional scheme. The notable result of this paper is that the increase of flexibility can be achieved through random arrangement of RDPS in the former half, and the compensation improvement can be achieved by through inverse arrangement in the latter half which make the distribution profile of each half link roughly symmetric with respect to the midway optical phase conjugator.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. Initial results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Artificial Intelligence and especially machine learning have noticed rapid advancement on image processing operations. However, its involvement in the architectural design is still in its initial stages compared to other disciplines. Therefore, this paper addresses the issues of developing an integrated bottom up digital design approach and details a research framework for the incorporation of Deep Convolutional Generative Adversarial Network (GAN) for early stage design exploration and generation of intricate and complex alternative facade designs for urban infill. This paper proposes a novel building facade design by merging two neighboring building’s architecture style, size, scale, openings, as reference to create a new building design in the same neighborhood for urban infill. This newly produced building contains the outline, style and shape of the parent buildings. A 2D urban infill building design is generated as a picture where 1) neighboring buildings are imported as a reference using mobile phone and 2)iFACADE decode their spatial adjacency. It is depicted the iFACADE will be useful for designers in the early design stage to generate new façades depending on existing buildings in a short time that will save time and energy. Besides, building owners can use iFACADE to show their architects their preferred architecture facade by mixing two building styles and generating a new building. Therefore, it is depicted that iFACADE can become a communication platform in the early design stages between architects and owners. Initial results properly define a heuristic function for generating abstract design facade elements and sufficiently illustrate the desired functionality of our developed prototype.

Let ${\mathcal{SR}}^*$ be the class of starlike functions with real coefficients, i.e., the class of analytic functions $f$ which satisfy the condition $f(0)=0=f'(0)-1$, Re{z f'(z) / f (z)} > 0, for $z\in\mathbb{D}:=\{z\in\mathbb{C}:|z|<1 \}$ and $a_n:=f^{(n)}(0)/n!$ is real for all $n\in\mathbb{N}$. In the present paper, the sharp estimates of the third Hankel determinant $H_{3,1}$ over the class ${\mathcal{SR}}^*$ are computed.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).

Regulatory macrophages (Mregs) are unique in that they have anti-inflammatory and immunosuppressive properties. Thus, treating inflammatory diseases using Mregs is an area of active research. Human Mregs are usually generated by culturing peripheral blood monocytes stimulated by macrophage colony-stimulating factor with interferon (IFN)-. Here, we generated Mregs with an elongated cell morphology from THP-1 cells stimulated with phorbol 12-myristate 13-acetate and cultured with arginylglycylaspartic acid and vitamin D3. These Mregs regulated macrophage function, and respectively downregulated and upregulated the expression of pro-inflammatory and immunosuppressive mediators. They also expressed Mregs-specific marker, such as dehydrogenase/reductase 9, even when exposed to inflammatory stimulants such as IFN-, lipopolysaccharide, purified xenogeneic antigen, and xenogeneic cells. The Mregs also exerted anti- inflammatory and anticoagulatory actions in response to xenogeneic cells and immunosuppressive effects on mitogen-induced Jurkat T-cell proliferation. Our method of generating functional Mregs in vitro without cytokines is simple and cost-effective.

Potential breeding habitat of egrets and herons was evaluated using the Maximum Entropy Model (MaxEnt). Model output can help guide management of nuisance egret and heron rookeries in urban forests of Daejeon Metropolitan City, Korea. This study examined 126 locations regarded as breeding sites of egrets and herons at the nationwide census conducted by the National Institute of Environmental Research between 2011 and 2012. In addition, 252 randomly selected locations were used to identify the significant variables among a total of 15 environmental variables within 4 factors (topography, natural environment, distance and climate). Twelve variables were significantly different between the breeding and randomly selected points. The final 10 variables were selected through Pearson’s correlation analysis. Using MaxEnt, breeding area was estimated using the 10 selected variables in Daejeon. The area under the receiver operating characteristic curve (AUC) was 0.950, which was the average value through 10-fold cross-validation to estimate the model reliability. The potential breeding habitat for egrets and herons was estimated to be 106.69 km2 (19.76% of the total area) in Daejeon. Within the estimated potential habitat, 11.82 km2 (12.46%) were less than 50 m from the residential district while 79.85 km2 (88.92%) were more than 50m from the residential district. Discriminative management strategies considering the breeding location of egrets and herons should be applied not only to minimize conflicts with residents, but also to maintain stable egret and heron breeding sites in Daejeon, Korea.

Very poor oral health, common among older adults, is associated with cognitive decline.This study aimed to investigate the association between denture use, chewing ability, and cognitive function in Korean middle-aged adults using samples representing middle-aged people at the national level. This longitudinal study included 9,998 middle-aged adults via Korea Longitudinal Study of Aging 7th special survey data. Denture use, chewing ability, health-related factors, and general characteristics were assessed by the Computer Assisted Personal Interview. After controlling general characteristics using a generalized estimating equation model, the association of denture use and MMSE scores with chewing ability of those with or without dentures and MMSE scores were analysed. Twenty-four percent of participants wore dentures among them, 35.1% complained of difficulty chewing when wearing dentures. Among participants who did not wear dentures, 16.4% complained of difficulty chewing. MMSE scores were lower among denture-wearers than non-denture wearers (β = -0.026, p < 0.001). In both groups, MMSE scores decreased with chewing difficulty and were significantly reduced among non-denture wearers (p < 0.05). Chewing ability was closely associated with cognitive function. Given the negative effect of difficulty chewing on cognitive function, maintaining chewing ability should be of great concern.

The frame construction of an apartment complex that consists of multiple buildings encounters various uncertainties, owing to the complex relationships among units of work. Currently, the period of such a construction is calculated based on the number of floors of the highest building in the complex. This study quantitatively analyzes an apartment frame construction period using a queue model and evaluates the validity of the estimated period. In this regard, a methodology is proposed for analyzing the construction period by applying the concept of a customer and a server. A case study on the duration of an apartment frame construction is conducted with Korea Land and Housing Corporation, which has supplied the largest number of apartments in South Korea. It was found that the stable state of a queue system was observed when the rate of server utilization was applied to the basement and aboveground floors. However, a stable state was not reached on the ground floor. This study includes non-working days in its calculation and quantitatively analyzes uncertainty factors during construction. Therefore, the findings can be practically utilized to quantitatively plan the durations of work units in an apartment frame construction.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

Lindera obtusiloba Blume has several activities, such as anti-inflammatory, anti-allergic, anti-tumor, anti-wrinkle, and antioxidant activities. Interleukin-6 (IL-6) is a classic pro-inflammatory cytokine that is associated with various functions, such as proliferation, invasion, inflammatory responses and functions within antioxidant defence systems. In this study, we investigated IL-6-induced STAT3 activation of lignan compounds isolated from L. obtusiloba. The structures of the isolated compounds were elucidated via spectroscopic nuclear magnetic resonance (NMR) and electrospray ionization mass spectrometry (ESI-MS). As a result, seven lignans were identified from L. obtusiloba. All the isolated compounds (1-7) were evaluated for their IL-6-induced STAT3 inhibitory effects in Hep3B cells using a luciferase reporter assay. Of the isolates, compounds 1 and 5 showed inhibitory effects against IL-6-stimulated STAT3 activation. Furthermore, the mRNA expression levels of inflammation-related genes such as CRP, IL-1b, and SOCS3 were significantly reduced by exposure to compound 1 and 5. The protein levels of p-STAT3, p-JAK2 in IL-6 induced U266 cells were regulated in the presence of lignans derived from Lindera obtusiloba by western blot assay. Based on the results, this study of L. obtusiloba demonstrates that the species has promise as a bioactive candidate for the treatment of IL-6-induced STAT3-related disease.

Background: Patients undergoing dual antiplatelet therapy (DAPT) may experience recurrent gastrointestinal bleeding (GIB). We investigated the clinical characteristics and risk factors for recurrent non-variceal upper gastrointestinal bleeding (NVUGIB) in patients who had experienced NVUGIB during receiving DAPT. Methods: We enrolled patients diagnosed with NVUGIB during receiving DAPT between 2006 and 2020. Definite bleeding was confirmed by esophagogastroduodenoscopy in all NVUGIB patients. Results: A total of 124 patients were diagnosed with NVUGIB during receiving DAPT. Male was predominant (n = 103, 83.1%), bleeding mostly from the stomach (n = 94, 75.8%) and peptic ulcers (n = 72, 58.1%). After successful hemostasis of NVUGIB, 36 patients (29.0%) experienced at least one episode of recurrent upper GIB, 19 patients (15.3%) died, and 7 (5.6%) patients had a bleeding-related death. Multivariate analysis showed that age was a significant factor for re-bleeding (odds ratio [OR],1.050; 95% confidence interval [CI]:1.001-1.102, P-value:0.047), all-cause mortality (OR,1.096; 95% CI:1.020-1.178, P=0.013), and re-bleeding related mortality (OR,1.187; 95% CI:1.032-1.364, P-value:0.016). In Kaplan-Meier analysis, the cumulative probabilities of re-bleeding, death, and bleeding-related death were significantly higher in patients aged 70 and older (P=0.008, &lt;0.001, and 0.009, respectively). Conclusion: Clinicians should be cautious about re-bleeding and mortality when elderly patients who experienced NVUGIB during receiving DAPT.Keywords: dual antiplatelet therapy; upper gastrointestinal tract; bleeding; mortality

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

There is a lack of data comparing sugammadex with anticholinesterase for the quality of anaesthesia recovery, especially following a single bolus dose of rocuronium. Thus, we evaluated the influence of reversal with sugammadex or neostigmine on post-operative quality of recovery by using the Post-operative Quality Recovery Scale (PQRS). A total of 86 patients undergoing trans-pars plana vitrectomy (TPPV) under general anaesthesia were intubated following a single bolus dose of rocuronium (0.6 mg/kg). At the end of surgery, patients were received either neostigmine or sugammadex. The quality of recovery was assessed using the PQRS at 15 minutes and 40 minutes after surgery, and on post-operative day 1. The recovery rate in the physiological domain was higher in the sugammadex group at 15 minutes after surgery (P = 0.02). Though there were no significant differences in the overall cognitive recovery domain, patients in the sugammadex group could recall more numbers in reverse order. However, there were no significant differences between the groups in the other domains of the PQRS. The use of sugammadex may increase the quality of the post-operative physiological recovery at early post-operative periods compared with neostigmine use following a single bolus dose of rocuronium in patients undergoing TPPV with general anaesthesia.

The application of 16S rRNA gene pyrosequencing has expanded our knowledge about the respiratory tract microbiome originally obtained using conventional, culture-based methods. In this study, we employed DNA-based molecular techniques for examining the sputum microbiome in bronchiectasis patients in relation to disease severity. Of 63 study subjects, 42 had mild and 21 had moderate or severe bronchiectasis, which was classified by calculating the FACED score based on FEV₁ (forced expiratory volume in 1 s, %) (F, 0–2 points), age (A, 0–2 points), chronic colonization by Pseudomonas aeruginosa (C, 0-1 point), radiographic extension (E, 0–1 point), and dyspnoea (D, 0–1 point). Bronchiectasis was defined as mild at 0–2 points, moderate at 3–4 points, and severe at 5–7 points. The mean age was 68.0 ± 9.3 years; 33 patients were women. Haemophilus (p=0.005) and Rothia (p=0.043) were significantly more abundant in the mild bronchiectasis group, whereas Pseudomonas (p=0.031) was significantly more abundant in the moderate or severe group. However, the alpha or beta diversity did not significantly differ among sputum microbiota, i.e. the same dominating genera were found in all samples. Further large-scale studies are needed to investigate the sputum microbiome in bronchiectasis.

Phytoremediation, a method of phytomanagement using the plant holobiont to clean up polluted soils, is particularly effective for degrading organic pollutants, such as alkanes and polycyclic aromatic hydrocarbons (PAHS). However, the respective contributions of host plants and their associated microbiota within the holobiont to the efficiency of phytoremediation is poorly understood. Identification of plant-associated bacteria capable of efficiently utilizing these compounds as carbon source while stimulating plant-growth, is a keystone for phytomanagement engineering in order to improve the efficiency of pollutant removal. In this study, we sampled the rhizosphere and the surrounding bulk soil of Salix purpurea and Eleocharis obusta from the site of a former petrochemical plant in Varennes, QC, Canada. Our objectives were to: (i) isolate and identify indigenous bacteria inhabiting these biotopes; (ii) assess the ability of isolated bacteria to utilize alkanes (dodecane and hexadecane) and PAHs (naphthalene, phenanthrene and pyrene) as the sole carbon source, and (iii) determine the plant growth-promoting (PGP) potential of the isolates using five key traits. A total of 438 morphologically different bacterial isolates were obtained, purified, preserved and identified through PCR and 16S rRNA gene sequencing. Identified isolates represent 62 genera, including taxa such as Acinetobacter, Arthrobacter, Bacillus, Enterobacter, Nocardia, Pseudomonas, Rhodococcus, Streptomyces and Variovorax. Approximately, 32% of bacterial isolates, including Arthrobacter, Pseudomonas, Streptomyces, Enterobacter, Nocardia, Acinetobacter and Microbacterium, were able to utilize all five different hydrocarbons compounds. Additionally, 5% of tested isolates belonging to genera Pseudomonas, Acinetobacter, Serratia, Klebsiella, Microbacterium, Bacillus and Stenotrophomonas possessed all five of the tested PGP functional traits. This culture collection of diverse, petroleum-hydrocarbon degrading bacteria, with multiple PGP traits, represents a valuable resource for future use in environmental bio- and phyto-technology applications, including phytoremediation of petroleum hydrocarbons contaminated soils and phytomanagement of anthropized areas.

The Advanced Meteorological Image (AMI) onboard GEOKOMPSAT 2A (GK-2A) enables the retrieval of dust aerosol optical depth (DAOD) from geostationary satellites using infrared (IR) channels. IR observations allow the retrieval of DAOD and the dust layer altitude (24 hour) over surface properties, particularly over deserts. In this study, dust events in northeast Asia from 2020 to 2021 were investigated using five GK-2A thermal IR bands (8.7, 10.5, 11.4, 12.3, and 13.3 μm). For the dust cloud, the observed brightness temperature differences (BTDs) of 10.5 and 12.3 μm were found to be always negative, while the BTD of 8.7 and 10.5 μm varies relying on the dust intensity. Making the best use of optical properties, a physical approach for DAOD lookup tables (LUTs) was developed using IR channels to retrieve the DAOD. This study simulated the characteristics of thermal radiation transfer using the forward model and dust aerosols can explain by BTD (10.5, 12.3 μm), which is an intrinsic characteristic of dust aerosol. The DAOD and property of dust can be gained from the brightness temperature (BT) of 10.5 μm and the BTD of 10.5, 12.3 μm. Additionally, the cumulative distribution function (CDF) was employed to strengthen the continuity of 24-hour DAOD, which was applied to the algorithm by calculating the conversion value coefficient for the DAOD error correction of the IR with daytime visible aerosol optical depth (VAOD) as the true value. The results show that DAOD product can be successfully used during both daytime and nighttime to continuously monitor the flow of yellow dust from the GK-2A satellite in northeast Asia. In particular, the validation result of IR DAOD was similar to that of the active satellite product (CALIPSO/CALIOP), which showed a tendency similar to that for IR DAOD at night.

Perfluorinated compounds (PFCs) are used in the manufacturing process of the semiconductor and display industries, and the need for emission reduction is growing as a greenhouse gas with a very large global warming potential. The decomposition characteristics of etch type and water film (WF) type plasma-wet scrubbers were investigated. The PFCs used in the study were CF4, SF6, NF3, CHF3, C2F6, C3F8, and C4F8, and the destruction removal efficiency (DRE) and by-product gas generation rate according to the changes in the parameters (total flow rate and power) of the plasma-wet scrubber were confirmed. When the total flow rate was 100 L/min and the measured maximum power (11 kW), the reduction efficiency of CF4 in the etch type was 95.60 % and the DRE of other PFCs was 99.99 %. And, in the WF type, the DRE of CF4 was 90.06 %, that of SF6 was 96.44 %, and that of other PFCs was 99.99 %. When the total flow rate was 300 L/min and 11 kW, the DRE of SF6 in the etch type was 99 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. And, in the WF type, the DRE of SF6 was 94.39 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. The by-product gas generation rate was significantly lower in the WF type.