This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

In this paper we analyze the relationship between bankruptcy risk and the corporate life cycle in Pakistan from 2005 to 2014. For this purpose, we run a Hierarchical Linear Mixed Model (HLM) for a sample of 301 non-financial listed firms in 12 different sectors. The empirical outcomes reveal that firms during introduction, growth and, decline stages (mature stage) of life-cycle experience higher (lower) bankruptcy risk. Moreover, in juxtaposition with growth stage, bankruptcy risk is higher at the introduction stage of life-cycle. These findings suggest that financial managers should be cautious about the financial fragility of the firm at each stage of corporate life-cycle. The results also entail that Pakistani firms do not follow a sequential pattern in their life-cycle rather they have the tendency to revert to a previous stage or jump to the next stage of life-cycle. This is the first study that empirically examines the association between firm life-cycle stage and corresponding bankruptcy risk and asserts that managers must incorporate the life-cycle effects into their financial planning and decision making for sustainable working of an enterprise.

This study clearly shows that the corona pandemic has a significant impact on consumers’ eating habits. More food is eaten overall, and more convenience products such as ready meals and canned food with a longer shelf life are purchased. The consumption of alcohol and confectionery has also increased. In return, the consumption of fresh fruit and vegetables has declined. It becomes clear that families who are financially affected by the pandemic represent a vulnerable group. With the increasing duration of the pandemic, repeated lockdowns, corona-related closings of schools and kindergartens, health consequences are to be expected in the medium to long term, especially for this population group.

The food system represents a key industry for Europe and particularly Germany. However, it is also the single most significant contributor to climate and environmental change. A food system transformation is necessary to overcome the system's major and constantly increasing challenges in the upcoming decades. One possible facilitator for this transformation are radical and disrup-tive innovations that start-ups develop. There are many challenges for start-ups in general and food start-ups in particular. Various support opportunities and resources are crucial to ensure the success of food start-ups. One aim of this study is to identify how the success of start-ups in the food system can be supported and further strengthened by players in the innovation ecosystem in Germany. There is still room for improvement and collaboration toward a thriving innovation ecosystem. A successful innovation ecosystem is characterised by a well-organised, collaborative, and supportive environment with a vivid exchange between the members in the ecosystem. The interviewees confirmed this, and although the different actors are already cooperating, there is still room for improvement. The most common recommendation for improving cooperation is learning from other countries and bringing the best to Germany.

High levels of meat consumption are increasingly being criticised for ethical, environmental, and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein that, in comparison to meat, offer a number of social, environmental and health benefits and may play a role in reducing meat consumption. However, there has been a lack of research on the role they can play in the policy agenda and how specific meat substitute attributes can influence consumers to replace partially replace meat in their diets.

Meat-based diets are still the norm and vegans and vegetarians represent only a small minority of the population. A transition respectively behavioural change towards a diet with less meat can only occur with the adoption of a positive attitude towards dietary changes based on reasons and motivations. The main aim of this study is to validate the so-called meat attachment scale (MEAS) for Germany in order to analyse if this construct is a barrier towards a diet with less meat in this country. The findings show that the MEAS can be applied in Germany and a similar structure as reported for Spain and other countries could be found. Furthermore, a correlation analysis demonstrated that food neophobia and MEAS are not correlated with each other. That is, that meat attachment represents an independent and single predictor for trust in food (processing) technologies as e.g. plant-based proteins or cultured meat.

High levels ofmeat consumption are increasingly being criticised for ethical, environmental, 2 and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein in 3 comparison to meat. This alternative offers several social, environmental and health benefits and may 4 play a role in reducing meat consumption. However, there has been a lack of research on how specific 5 meat substitute attributes can influence consumers to replace or partially replace meat in their diets. 6 Research demonstrates that in many countries consumers are highly attached to meat.They consider 7 it as an essential and integral element of their daily diet. For these consumers which are not interested 8 in vegan or vegetarian alternatives to meat, so-called meathybrids could be a low-threshold option 9 for a more sustainable food consumption behaviour. In meathybrids only a fraction of the meat 10 product (e.g. 20% to 50%) is replaced with plant-based proteins. In this paper, the results of an online 11 survey with 500 German consumers are presented with focus on preferences and attitudes relating 12 to meathyrids. The results show that more than fifty percent of consumers substitute meat at least 13 occasionally. Thus, about half of the respondents reveal an eligible consumption behaviour in respect 14 to sustainability and healthiness to a certain degree. Concerning the determinants of choosing either 15 meathybrid or meat it becomes evident that the highest effect is exerted by the health perception. The 16 healthier meathybrids are perceived, the higher is the choice probability. Thus, this egoistic motive 17 seems to outperform altruistic motives like animal welfare or environmental concerns when it comes 18 to choice for this new product category.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

High levels of meat consumption are increasingly being criticised for ethical, environmental, and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein in comparison to meat. This alternative offers several social, environmental and health benefits and may play a role in reducing meat consumption. However, there has been a lack of research on how specific meat substitute attributes can influence consumers to replace or partially replace meat in their diets. Research demonstrates that in many countries consumers are highly attached to meat. They consider it as an essential and integral element of their daily diet. For these consumers which are not interested in vegan or vegetarian alternatives to meat, so-called meathybrids could be a low-threshold option for a more sustainable food consumption behaviour. In meathybrids only a fraction of the meat product (e.g. 20% to 50%) is replaced with plant-based proteins. In this paper, the results of an online survey with 501 Belgium consumers are presented with focus on preferences and attitudes relating to meathyrids. The results show that more than fifty percent of consumers substitute meat at least occasionally. Thus, about half of the respondents reveal an eligible consumption behaviour in respect to sustainability and healthiness to a certain degree. Concerning the determinants of choosing either meathybrid or meat it becomes evident that a strong effect is exerted by the health perception. The healthier meathybrids are perceived, the higher is the choice probability. Thus, this egoistic motive seems to outperform altruistic motives like animal welfare or environmental concerns when it comes to choice for this new product category.

Biomedical implants are the need of this era due to the increase in number of accidents and follow-up surgeries. Different types of bone diseases such as osteoarthritis, osteomalacia, bone cancer, etc. are increasing globally. Mesoporous bioactive glass nanoparticles (MBGNs) are used in biomedical devices due to their osteointegration and bioactive properties. In this study, silver (Ag) and strontium (Sr) doped mesoporous bioactive glass nanoparticles (Ag-Sr MBGNs) were prepared by a modified Stöber process. In this method, Ag+ & Sr2+ were co-substituted in pure MBGNs to harvest the antibacterial properties of Ag ions, as well as pro-osteogenic potential of Sr2 ions. The effect of the two ion concentration on morphology, surface charge, composition, antibacterial ability, and in-vitro bioactivity was studied. Scanning electron microscopy (SEM), X-Ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) confirmed the doping of Sr and Ag in MBGNs. SEM and EDX analysis confirmed the spherical morphology and typical composition of MBGNs, respectively. The Ag-Sr MBGNs showed a strong antibacterial effect against Staphylococcus carnosus and Escherichia coli bacteria determined via turbidity and disc diffusion method. Moreover, the synthesized Ag-Sr MBGNs develop apatite-like crystals upon immersion in simulated body fluid (SBF), which suggested that the addition of Sr improved in-vitro bioactivity. The Ag-Sr MBGNs synthesize in this study can be used for the preparation of scaffolds or as a filler material in the composite coatings for bone tissue engineering.

Endopolygalacturonase (EndoPGase) is one of the crucial pectinases belonging to the class of carbohydrase. The catalytic action of EndoPGase captivate the attention for production of this extremely valuable catalyst of industrial sector. The main focus was to ascertain a potential bacterial candidate for endoPGase production. The isolated bacterial strain was further identified by 16S rDNA gene sequencing. A genomic library was constructed by using Lambda ZAP II vector system to investigate the pectinolytic potential of the expressed genes. The parameters for enzyme biosynthesis were optimized by single as well as multiple factor approach at a time. The results of our investigation led to the identification of a potent strain of Bacillus subtilis NR2. The strain was found active for pectic enzyme activity under shaking- flask fermentation at pH 5.0 and 50 °C temperature of incubation. Among all monomeric and polymeric substrates, citrus pectin followed by wheat bran was considered the best enzyme inducers at 1 % concentration. Moreover, an increasing trend in enzyme activity was observed with the increasing inducer concentration. The combined effect of three variables (pH, substrates, and substrate concentration) was explored by response surface methodology involving Box Benken Design (BBD). The study concluded that the soil isolated B. subtilis can be utilized for commercial scale pectinase enzyme production.

The emergence of unmanned aerial vehicles (UAVs) raised multiple concerns, given their potential for malicious misuse in unlawful acts Vision-based counter-UAV applications offer a reliable solution compared to acoustic and radio frequency-based solutions because of their high detection accuracy in diverse weather conditions. The existing solutions work well on trained datasets, but their accuracy is relatively low for real-time detection. In this paper, we model deep learning-empowered solutions to improve the multi-class UAV's classification performance using single-shot object detection algorithms YOLOv5 and YOLOv7. The transfer learning is employed for performance improvement and rapid training with improved results. We customized a multi-class dataset containing multi-rotor, fixed-wing, and single-rotor UAVs in challenging weather conditions. Experiments show that the integration of transfer learning has achieved good results, with an overall best average-classification precision of 94\%, an average recall of 93.1\%, a mAP$@$0.5 average of 95.3\%, and an average F1 score of 92.33\%. The dataset and code are available as an open source: https://github.com/ZeeshanKaleem/YOLOV5-Large-vs-YOLOV7.git

In this paper a new monolithic Eulerian formulation in the framework of non-classical continuum is presented for the analysis of fluid-strucutre interaction problems. In this respect, Cosserat continuum theory taking into account the micro-rotational degrees of freedom of the particles is considered. Continuum description of the model and variational formulation of the governing flow dynamics for non-classical -fluid-structure interaction nCFSI is presented. The model is analyzed by computing a well known benchmark problem by Hecht and Pironneau [16]. The algorithmic description is presented and implemented using FreeFEM++. Code is validated with the benchmark solution of Turek and Hron [38] in case of flow around a flag attached with cylinder. New microstructral behavior of the solution is studied and numerical simulations and results are shown in the form of figures. Some interesting feature of the flow is observed and microstructural characteristics are discussed.

This study investigated the ability of a HYDRUS 1D model for predicting the vertical distribution of potassium iodine (200 ppm) in soil columns after amendment with five different common remediation materials (gypsum, lime, fly ash, charcoal and sawdust) at a rate of 2.5% (w/w), relative to an unamended control soil. Results shows that relative to the unamended soil, iodine leaching was decreased by all amendments but that the magnitude of the decreases varied with the soil amendment applied. Iodine content was highest in the upper layer of the soil columns and decreased progressively with soil depth. The model was evaluated via comparison of the model simulated values with measured values from the soil column studies. The results showed that the HYDRUS 1D model efficiency was near to 1, indicating that the stimulated results were near to the measured values. Therefore, this study showed that iodine leaching through a soil could be ascertained well using a HYDRUS 1D model. The model over predicted iodine leaching, resulting to a weak correspondence between the simulated and the measured results for iodine leaching. This suggests that the HYDRUS-1D model does not explain accurately different organic and inorganic amended soil and the preferential flow that occurs in these columns. This may be due to the fact that Freundlich isotherm, which is part of the transport equations, does not sufficiently describe the mechanism of iodine adsorption onto the soil particles. This study would help to select amendments for an effective management strategy to reduce exogenous iodine losses from agro-ecosystems. This would also improve understanding of iodine transport in soil profile.

The construction industries face several challenges related to productivity. Productivity mainly depends upon labour effort and performance. The poor productivity of labour is one of the major reasons of time over-runs and increasing cost in construction projects. Our study aims to build a comprehensive assessment on the relationship between various factors that affect labour productivity in the construction of prestressed concrete Buildings in Ghana. A sample of 200 re-spondents collected from workers of Construction Company in Ghana. The questionnaire was designed which comprises two parts; the first part contains background information of the staff of construction company while second section explores the opinion of the staff regarding factors af-fecting labour productivity. The Smart-PLS was utilized to analyze and estimate the relationship among construct variables. By utilizing relative importance index and multiple linear regressions, it is identified that the management factor such as inadequate incentives; material factor such as poor quality of material; labour factors such as poor quality and training of labors; supervision factor such as incompetence of site supervisor; equipment factor such as frequent damage of equipment have a negative and significant relationship with labour productivity in the construc-tion of prestressed concrete buildings in Ghana. The findings of this study recommend that in order to improve labour productivity, the construction industries must conduct labour productivity measurements by adopting schedule for procurement of materials, safety programs, motivational system, and frequent meeting with project professionals.

Thalassemia is genetic blood disease cause by absence or decrease of one or more of the globin chain synthesis. Beta thalassemia is characterized by one or more mutations in beta globin gene. Absence or reduced amount the of beta globin chains cause ineffective erythropoiesis which leads to anemia. Beta thalassemia has been further divided into three main forms: Thalassemia minor/silent carrier, major and intermedia. More severe form is thalassemia major in which patients depend upon blood transfusion for survival and high level of iron occur as a consequence of consistent blood transfusion. Over loaded iron invokes the synthesis of reactive oxygen species that are toxic in redundancy and triggering the impairment to vascular, endocrine and hepatic system. Thalassemia can be diagnosed and detected through various laboratory tests such as blood smear, prenatal testing (genetic testing of amniotic fluid), DNA analysis (genetic testing) and complete blood count. Treatment of thalassemia intermedia is symptomatic but it can also be managed by splenectomy and folic supplementation. While thalassemia major can be treated by transplantation of bone marrow, regular transfusion of blood and iron chelation treatment, stimulation of fetal hemoglobin production, hematopoietic stem cell transplantation and gene therapy.

Management of chronic inflammation and wounds has always been a key issue in the pharmaceutical and healthcare sector. Curcumin (CCM) is an active ingredient extracted from turmeric rhizomes that has antioxidant, anti-inflammatory, and antibacterial activities, thus showing significant effectiveness toward wound healing. However, its shortcomings such as poor water solubility, poor chemical stability and fast metabolic rate limit its bioavailability and long-term use. In this context, hydrogels appear to be a versatile matrix for carrying and stabilizing drugs due to the biomimetic structure, soft porous microarchitecture, and pleasant biomechanical properties. The drug loading/releasing efficiencies can also be controlled by use of highly crystalline and porous metal organic frameworks (MOFs). Here, a flexible hydrogel composed of sodium alginate (SA) matrix and CCM-loaded MOFs was constructed for long-term drug release and antibacterial activity. The morphology and physicochemical properties of composite hydrogels were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), ultraviolet visible spectroscopy (UV-Vis), Raman spectroscopy and mechanical property tests. The results showed that the composite hydrogel was highly twistable and bendable to mechanically comply with human skin. The as-prepared hydrogel could capture efficient CCM for slow drug release as well as effective killing of bacteria. Therefore, such composite hydrogel is expected to provide a new management system for chronic wound dressings.

For bounded unit interval, we propose a new Kumaraswamy generalized (G) family of distributions from a new generator which could be an alternate to the Kumaraswamy-G family proposed earlier by Cordeiro and de-Castro in 2011. This new generator can also be used to develop alternate G-classes such as beta-G, McDonald-G, Topp-Leone-G, Marshall-Olkin-G and Transmuted-G for bounded unit interval. Some mathematical properties of this new family are obtained and maximum likelihood method is used for estimating the family parameters. We investigate the properties of one special model called a new Kumaraswamy-Weibull (NKwW) distribution. Parameter estimation is dealt and maximum likelihood estimators are assessed through simulation study. Two real life data sets are analyzed to illustrate the importance and flexibility of this distribution. In fact, this model outperforms some generalized Weibull models such as the Kumaraswamy-Weibull, McDonald-Weibull, beta-Weibull, exponentiated-generalized Weibull, gamma-Weibull, odd log-logistic-Weibull, Marshall-Olkin-Weibull, transmuted-Weibull, exponentiated-Weibull and Weibull distributions when applied to these data sets. The bivariate extension of the family is proposed and the estimation of parameters is given. The usefulness of the bivariate NKwW model is illustrated empirically by means of a real-life data set.

The versatile one-pot green synthesis of a highly concentrated and stable colloidal dispersion of AgNPs was carried out using the self-assembled tannic acid without using any other hazardous chemicals. Tannic acid (Plant-based polyphenol) was used as a reducing and stabilizing agent for silver nitrate in a mild alkaline condition. The synthesized AgNPs were characterized for their concentration, capping, size distribution, and shape. The experimental results confirmed the successful synthesis of nearly spherical and highly concentrated (2281 ppm) AgNPs, capped with poly-tannic acid (AgNPs-PTA). The average particle size of AgNPs-PTA was found 9.90 ± 1.60 nm. The colloidal dispersion of synthesized nanoparticles was observed stable for more than 15 months in the ambient environment (25 oC, 65 % relative humidity). The synthesized AgNPs-PTA showed an effective antimicrobial activity against Staphylococcus Aureus Escherichia coli. Ag-PTA also exhibited enhanced catalytic properties. It reduces 4-nitrophenol into 4-aminophenol in the presence of NaBH4 with a normalized rate constant (Knor = K/m) of 615.04 mL·s-1·mg-1. Furthermore, AgNPs-PTA were stable for more than 15 months under ambient conditions. The unique core-shell structure and ease of synthesis render the synthesized nanoparticles superior to others, with potential for large-scale applications, especially in the field of catalysis and biomedical.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

Lie algebra plays an important role in the study of singularity theory and other field of sciences. Finding numerous invariants linked with isolated singularities is always a main interest in the classification theory of isolated singularities. Any Lie algebra that characterizes simple singularity produces a natural question. The study of properties such as to find the dimensions of newly defined algebra is a remarkable work. Hussain, Yau and Zuo \cite{HYZ10} have been found a new class of Lie algebra \texorpdfstring{ $ \mathcal{L}_ k (V)$}{LG}, \texorpdfstring{$k\geq 1$}{LG} i.e., Der ($M_{k}(V), M_{k}(V)$) and purposed a conjecture over its dimension $\delta_{k}(V)$ for $k\geq0$. Later they proved it true for $k$ up to $k=1,2,3,4,5$. In this work, the main concern is whether it's true for a higher value of $k$. According to this, we calculate first, the dimension of Lie algebra \texorpdfstring{$\mathcal{L}_ k (V)$}{LG} for $k=6$ and then compute the upper estimate conjecture of fewnomial isolated singularities. Along with, we also justify the inequality conjecture: \texorpdfstring{$\delta_{k+1}(V) < \delta_{k}(V)$}{LG} for $k=6$. Our calculated results are innovative and a new addition to the study of singularity theory.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

Polymorphism in cytochrome P450 (CYP) 2C9 enzyme is known to cause significant inter-individual differences in drug response and occurrence of adverse drug reactions. Different alleles of the CYP2C9 gene have been identified but the notable alleles responsible for reduced enzyme activity are CYP2C9*2 and CYP2C9*3. No pharmacogenetic data is available on CYP2C9*2 and CYP2C9*3 alleles in Pakistani population. In Pakistan pharmacogenetics which examines the relationship between genetic factors and drug response, are in the early stages of development. We for the first time investigated the association between the CYP2C9 variant alleles CYP2C9*2 and CYP2C9*3 and the incidence of hypoglycemia in diabetic patients who were receiving the sulfonylurea medications. A total of n=400 individuals of Pashtun ethnicity were recruited from ten different districts of Khyber Pakhtunkhwa, Pakistan to participate in the study. The study participants were divided into two distinct groups: the case group (n=200) and the control group (n=200). The case group consisted of individuals with Type 2 Diabetes Mellitus (T2DM) who were receiving sulfonylurea medications and experience hypoglycaemia with it whereas the control group included individuals with T2DM who were receiving sulfonylurea medication but did not experience sulfonylurea-induced hypoglycaemia (SIH). Blood samples were obtained from study participants following informed consent. DNA was isolated from whole blood samples using Wiz-Prep DNA extraction kit. Following DNA isolation, CYP2C9 alleles were genotyped using MassARRAY sequencing platform at centre of genomics Rehman Medical Institute (RMI). The frequency of CYP2C9*2 (low activity allele) was more frequent in the diabetic patients with sulphonylurea-induced hypoglycaemia (SIH) compared to the control group (17.5% vs. 6.0%, p=0.021). The frequency of its corresponding genotype CYP2C9*1/*2 was higher in cases compared to control group (10% vs. 6% with P=0.036), same was true for genotype CYP2C9*2/*2 (7% vs. 3.5 % with P=0.028). Logistic regression analysis evident potential association of CYP2C9*2 allele and its genotypes with SIH. When adjusted for confounding factors such age, weight, sex, daily dose of sulphonylurea and triglyceride level the association between the CYP2C9*2 allele and hypoglycemia remains consistent. Confounding factors played no role in SIH because both groups (cases and controls) were closely matched in term of age, weight, sex, mean daily dose of sulphonylurea and trigyleride levels. Our study suggests that genetic information about a patient's CYP2C9 gene/enzyme can potentially assist physicians in prescribing the most suitable and safest drug based on their genetic make-up.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

Mill scale is the by-product of iron and steel industry. It can be recycled via sinter plant or solid as sinter feed materials. 85 to 90% of the constituent particles are more than 0.008 inches. The iron content is near around 70 %, with a very small amount of alkaline compounds and non-ferrous metals. Mill scale is polluted and contaminated with lubricants, oils and greases from the equipment. In this experiment for recovering of oil from mill scale, it is treated with three different methods. Then all methods were compared according to the ability of oil elimination and iron recovered. After washing and boiling with surfactants, large amount of polluted waste water becomes a problem for environment so this wastewater was utilized for making of Microbial Fuel Cells (MFCs), production of electricity in MFC depends on the biodegradation of organic materials, so different waste were added in wastewater for making MFC. The remaining of MFC was converted in bioethanol, biodiesel and biofertilizer. So this research is economical and environmentally friendly and fulfilled the important aspect of green environment with zero waste. It will be a mile stone in the research of metallurgy, environmental engineering, recycling technology and zero waste management.

Purpose: The aim of this research was to prepare adhesive nanoparticles for the topical application of Minoxidil (MXD). Methods: Thiolated β-CDs were prepared via conjugation of cysteamine with oxidized CDs. MXD was encapsulated within thiolated and unmodified β-CDs. Nanoparticles (Thio-NP and blank NP) were prepared by ionic gelation of CDs with chitosan. Particle size and zeta potential were measured. FTIR analyses were performed for characterization of inclusion complex. Drug dissolution studies were carried out. An in vitro adhesion study over human hair was performed. An in vivo skin irritation study was performed. Ex vivo drug uptake was evaluated by using a Franz diffusion cell. Results: Thiolated β-CDs presented 1804.68 ± 25 μmol/g thiol groups and 902.34 ± 25 μmol/g disulfide bonds. Nanoparticles displayed particle sizes within a range of 231 nm to 319 nm. The zeta potential was in the range of ̶ 8.1 to + 12.0. FTIR analyses confirmed no interaction between the excipients and drug. Delayed drug release was observed from Thio-NP. Thio-NP retained over hair surfaces for a significantly longer time. Similarly, drug retention was significantly improved. Thio-NP displayed no irritation over rabbit skin. Conclusion: Owing to the above results, nanoparticles developed with MXD-loaded thiolated β-CDs might be a potential drug delivery system for topical scalp diseases.

The wettability of the oil-brine-rock systems is very challenging mainly for the carbonate reservoirs and it plays a significant role to enhance the oil recovery (EOR). Carbonate rocks are mad-up of complex lithology, hence these requires careful treatments in controlling their wetting behavior for enhanced oil recovery. Therefore, it is extremely important to modify their wettability from an oil-wet rock behavior to a water-wet so that the residual oil can be produced efficiently. Thus, the present study has examined the effectiveness of alumina nanofluid as well as a new chemical methyl blue to alter the wettability. The methyl blue is released on massive scale from various industries i.e. pharma, textile and food industry which is a key environmental concern which contaminates the water table. Hence the study, explores the effects of MB and alumina nanofluid on the wettability. The effect of nanofluids formulated via dispersing the alumina nanoparticles in aqueous solutions at various concentration (0. 0.05, 0.3, 0.50, 0.75 and 1.0 wt. %) were tested for wettability modification under different physio-thermal conditions. Subsequently, the wettability change was examined for the samples treated with different concentrations of MB (10, 15, 30, 50 and 100 mg/L) for 7-days at two different temperatures of (25 and 50 0C). The results showed that hydrophobicity of the SML carbonate rock has significantly reversed while treating with alumina nanofluids and MB. Thus, the wettability modification/reversal via treatment of MB and alumina nanofluid can be an effective mechanism to hydrogen injection and for EOR processes.

Micro-expression (ME) is one of the key psychological stress reactions. It is a modest, spontaneous facial mechanism. ME has significant applicability in a variety of psychologically-related sectors because to its precision and unpredictability with regard to psychological manifestations. Nevertheless, the current Micro-expression recognition (MER) algorithms have poor accuracy and a limited quantity of ME data, and this study issue has not been thoroughly investigated. Therefore, we present an approach for deep learning based on a Spatio-temporal capsule network (STCP-Net). STCP-Net has four components: a jitter reduction module, a differential feature extraction module, an STCP module, and a fully linked layer. The first two modules are aimed to extract diversifying differential features more precisely and to limit the influence of head jitter. The STCP module is used to extract Spatio-temporal features layer by layer, taking the temporal and geographical connection between features into account. This research runs sufficient trials using the Leave One Subject Out (LOSO) methodology for cross-validation using the CASMEII dataset. The conclusion and analysis demonstrate that the algorithm is innovative and efficient.

A huge number of applications available for Android-based smartphone devices have emerged over the past years. Due to which a huge number of malicious applications has been growing explosively. Many approaches have been proposed to ensure the security and quality of application in the markets. Usually, Machine Learning approaches are utilized in the classification process of malicious application detection. Calculating accurate results of characterizing applications behaviors, or other features, has a direct effect on the results with Machine Learning calculations. Android applications emerge so quickly. The behavior of current applications has gotten progressively malicious. The extraction of malware-infected features from applications is thus become a difficult task. According to our knowledge, a ton of features have been extricated in existing work however no survey has overviewed the features built for identifying malicious applications efficiently. In this paper, we will in general give an extensive review of such sort of work that identifies feature applications by describing various practices of uses with various kinds of features. In this survey we have discussed the following dimensions: extraction and selection of feature methods if any, methods of detection and evaluation performed. In light of our review, we notice the issues of investigating malware-affected features from applications, give the scientific categorization and demonstrate the future headings.

Machine Learning (ML) and Artificial Intelligence(AI) have revolutionized almost all fields that are linked to the acquisition of intelligent behavior in the real world. It is an attractive alternative for a researcher of artificial intelligence. Contrary to rule-based programming, ML is an algorithmic approach in which learning comes from existing data. The more data we have these computer systems look at, we say we’re ‘training’ the computer system, and as the computers begin to identify patterns in the data, identify abnormalities in the data from these abnormalities we improve the system architect according to the requirement. This article introduces the use of comprehensive concepts of machine learning, in general, particular, and their potential applications in communications. Furthermore, the current state and futuristic potentials of enabling universal communication with implications of machine learning methods have been explained. In this review paper, we offer a comprehensive talk on distinctive methods/techniques of information analytics, artificial intelligence (AI), and machine learning (ML) moved forward the contact aware communication system.

Incorporating substantial sustainable development issues into teaching and learning is the ultimate task of Education for Sustainable Development (ESD). The purpose of our study is to identify the confused students who have failed to master the skill(s) given by the tutors as a homework using Intelligent Tutoring System (ITS). We have focused ASSISTments, an ITS in this study and scrutinized the skill-builder data using machine learning techniques and methods. We used seven candidate models that include: Naïve Bayes (NB), Generalized Linear Model (GLM), Logistic Regression (LR), Deep Learning (DL), Decision Tree (DT), Random Forest (RF), and Gradient Boosted Trees (XGBoost). We trained, validated and tested learning algorithms, performed stratified cross-validation and measured the performance of the models through various performance metrics i.e., ROC (Receiver Operating Characteristic), Accuracy, Precision, Recall, F-Measure, Sensitivity & Specificity. We found GLM, DT & RF are high accuracies achieving classifiers. However, other perceptions such as detection of unexplored features that might be related to the forecasting of outputs can also boost the accuracy of the prediction model. Through machine learning methods, we identified the group of students which were confused attempting the homework exercise and can help students foster their knowledge, and talent to play a vital role in environmental development.

The diamondback moth (DBM), Plutella xylostella L. (Lepidoptera: Plutellidae) is very destructive crucifers specialized pest that has resulted in significant crop losses worldwide. The pest is well attracted to glucosinolate-containing crucifers such as; Barbarea vulgaris (Brassicaceae), and generally to other plants in the genus Barbarea. B. vulgaris on their part, build up resistance against DBM and other herbivorous insects using glucosinolates; that are plant secondary metabolites used in plant defense–contained only in plants of the order Brassicales. Aside glucosinolates, plants in this genus Barbarea (Brassicaceae) also contain saponins; which is toxic to insects and act as feeding deterrents for plant herbivores, most importantly, DBM, as it was found to prevent the survival of DBM larvae on the plant. Saponins are plant secondary metabolites have been established in higher concentrations in younger in contrast to older leaves within the same plant. Previous studies have found a relationship between ontogenetical changes in the host plant’s saponin content and attraction/resistance to P. xylostella. The younger leaves recorded higher concentrations of glucosinolates and saponins, which naturally attracts the plant herbivores. DBM was reported to have evolved mechanisms to avoid the toxicity of the former. The plant-herbivore had adapted glucosinolates for host plant recognition, feeding and oviposition stimulants. Despite the adaptation for oviposition by P. xylostella adults, larvae of the insect cannot survive on the same plant. An example is in some varieties of B. vulgaris. The triterpenoid saponins which act as feeding deterrents in larvae are responsible for this direct defense mechanism against P. xylostella. In the future, trials by plant breeders could aim at transferring this insect resistance to other crops. The previous trials had limited because of lack of knowledge on the biosynthetic pathways and regulatory networks of saponins. Herein, we discussed exclusively; saponins mediated plant defense mechanisms against the DBM.

COVID-19 has created anxiety not only in individuals but also in health organizations, and countries worldwide. Not a single industry is left un-influenced and loss is being estimated in billions of dollars. The widespread of this pandemic disease has challenged researchers all over the world. Some of the researchers are working to invent its cure while, others are applying computing technologies to stop its spread, by analyzing and identifying patterns for prediction and forecasting. This is by no doubt the hottest area of research for the last 100 years. This survey has targeted the research published in computing sub-domains to combat the pandemic. The survey has clustered the scientific efforts into logical groups: surveillance, metrological effects, social media analytics, image processing and business and economy, analysis and modeling. It will serve as a leading source for the followings: researchers who want to identify what has been achieved in different computing sub-domains, those who need fresh authenticated datasets openly accessible for different research contexts and what are future directions in this area of research. The findings of analysis and modeling can be also useful for government agencies who want to set priorities and formulate policies.

This study investigates the influence of economic growth on CO2 emissions levels in three developed countries—Argentina, Equatorial Guinea, and South Korea—based on their status as high-income countries. We test the environmental Kuznets curve (EKC) hypothesis using the time series approaches to check the relationship and direction of causality among the variables over a sample spanning 1974–2020. The results show an inverted U-shaped short-run relationship in all three countries. In the long run, only South Korea supports the EKC hypothesis. Further, Granger causality results indicate the existence of causality. These long-run causal relationships between economic growth and emissions recommend one policy implication that wealthy governments must expand investments in renewable clean energy projects and R&D, with regulatory measures to suppress harmful environmental procedures and support environmentally friendly development.

Glaciers in northern Pakistan are a prime source of fresh water, providing headwater in the Indus River System and serving as a lifeline to millions of people in the region. These glaciers undergo continuous changes by melting due to global warming or accumulation due to snowfall/precipitation at higher altitudes. In this study, we used remote sensing data to quantify glacier changes in spatiotemporal variability in the past three decades. Five glaciers in the Gilgit region (near the junction of the Hindukush and Karakoram Mountains) with an extent of less than 5 square kilometers were selected, namely Phakor glacier, Karamber glacier, East Gammu glacier, Bhort glacier, and Bad-e-Swat glacier. The fluctuations in these glaciers were monitored using a digital elevation model (DEM) and a cloud-free continuous series of Landsat satellite pictures from the minimal snow cover season. The annual climatic trends were studied through spatially interpolated gridded climate data WοrldClim version-1 climate database for 1970 – 2000. We used it to study the variations of minimum and maximum temperature, solar radiation, and precipitation by preparing sub-sets from the original global grids. The temporal assessment of Bhort, Bad-e-Sawat, East Gammu, Karamber, and other rivers was also carried out. It is observed that the glaciers in the Gilgit watershed are rather stable. The little variability of glaciers is due to their geographic condition, altitude, topography, and orientation. The mapped glacier classes have been validated to check the accuracy assessment through an error matrix method. The kappa coefficient from the error matrix has been calculated to be 84 %. The study makes a critical input to a greater understanding of watershed controlling and hydrological processes in the upper Indus catchment's Gilgit watershed.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

Concrete is a very common construction material. As time prevails, cracks often appear in structures that pose a threat to strength and durability, which ultimately affect the structural integrity of concrete. Extensive work has been carried out in past on utilization of Carbon Fiber Reinforced Polymer (CFRP) as a repair material. But, this research particularly focuses on: multiple fiber layers i.e. single and double, traditional concrete mix ratio with locally available materials and varying flexural reinforcement. Furthermore, this work presents an experimental analysis to strengthen the Reinforced Concrete (RC) beams using SikaWrap- 230 C as a CFRP wrap, and Sikadur-330 as a bonding material. The comparison between single and double layers of CFRP is of major interest in this research. Six reinforced concrete beams were repaired with CFRP and tested under three-point bending test. For these specimens, load deflection behavior along with crack propagation and failure of beams were studied. Experimental results show that beams repaired using CFRP wrapping achieved higher flexural capacity and ductility as compared with reference beam. Moreover, results reveal that introduction of second layer of fiber caused around 4-5.2% increment in flexural strength and resulted in higher ductility of RCC beam.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Diabetes is a life-threatening disease and chronic diabetes affects the parts of the body including the liver, kidney and pancreas. The root cause of diabetes is mainly associated with oxidative stress produced by reactive oxygen species. The minocycline is a polyphenolic drug with excellent antioxidant activities. The objective of the present study was to investigate the antidiabetic potential of minocycline modified silver nanoparticles (Mino/AgNPs) against alloxan-induced diabetic mice. The Mino/AgNPs were synthesized using minocycline as reducing and stabilizing agents. UV-vis, FTIR, X-ray diffraction (XRD) and transmission electron microscopy (TEM) were applied for the characterization of Mino/AgNPs. The 2,2-diphenyl-1-picrylhydrazyl (DPPH) free radical scavenging assay was conducted to determine the antioxidant potential of newly synthesized Mino/AgNPs. The results revealed that the Mino/AgNPs showed higher radical scavenging activity (IC50 = 19.7 µg/mL) as compared to the minocycline (IC50 = 26.0 µg/mL) and ascorbic acid (IC50 = 25.2 µg/mL). Further, the Mino/AgNPs were successfully employed to examine their antidiabetic potential against Alloxan-induced diabetic mice. Hematological results showed that the mice treated with Mino/AgNPs demonstrated a significant decrease in fasting blood glucose level and lipid profile as compared to the diabetic group. The histopathological examination confirmed that the diabetic mice treated with Mino/AgNPs showed significant recovery and revival of histo-morphology of kidney, central vein of liver and islet cells of the pancreas compared to the diabetic mice. Hence Mino/AgNPs have good antidiabetic potential and could be an appropriate nanomedicine to prevent the development of diabetes.

Punica granatum (PG) or Pomegranate is a bush, having many trunks and often get taller 1.8 to 4.7m long and their leaves are shiny and fleshy, approximately 7 to 8cm in length. Traditionally, it is used in diarrhea and dysentery due to its strong constricting property. Punica Granatum covering used in dysentery, diarrhea, piles, bronchitis. It is also used to minimize the risk of heart disease. The peel extract of Punica Granatum contain methanol and their dried peels has antidiarrheal venture, also help in wound healing activity. Peels of the pomegranate also holds around 60% of the fruit and they contain different types of ingredients including ellagitannins and proanthocyanidin compounds and minerals such as calcium, phosphorus, magnesium, potassium, flavonoids and sodium. Some animals were found in different local areas with both acute and chronic diarrhea. The condition of these animals were quite miserable because of dehydration and loss of electrolytes in the body cells of the animals. They were unable to move due to seriousness of the disease. 8 grams of PG Peel Powder mixed with 1 liter of water, 2 g of PG Peel Powder mixed with 250 ml water and 8 g of PG Peel Powder mixed with 1 liter of water were administrated orally by using sterilized bottles to the selected three cases. 3 days after the administration of different doses, all cases of diarrheal animals show a significant recovery. The condition of the animals seem to be healthier. Before administration of the pomegranate peel powder extract, all three cases had weak body structure due to diarrhea. Watery stool that may be yellow in color and mucus was also evident in the stool, due to this reason the patient calf was weak and depressed. In sometimes they also show unconsciousness and blood glucose levels seem to be reduced from the normal level.

Let G be a graph with n vertices and let 1; 2; : : : ; n be the eigenvalues of Randic matrix. The Randic Estrada index of G is REE(G) = Ón i=1 ei . In this paper, we establish lower and upper bounds for Randic index in terms of graph invariants such as the number of vertices and eigenvalues of graphs and improve some previously published lower bounds.

This comprehensive article explores Massive MIMO (M-MIMO) design and its associated concepts, focusing on the seamless integration requirements for Beyond 5G (B5G) and 6G networks. Addressing critical aspects such as RF chain reduction, pilot contamination, Cell-Free MIMO, and security considerations, the article delves into the intricacies of M-MIMO in the evolving landscape of B5G. Moreover, the emerging MIMO concepts in this article include AI-enabled M-MIMO three-dimensional beamforming, reconfigurable intelligent surfaces, visible light communication, and THz spectrum utilization. This review highlights challenges and open research issues, including Narrow Aperture Antenna Nodes, Plasmonic Antenna Arrays, Integrated Sensing with M-MIMO, and the application of Federated Learning in M-MIMO systems. By examining these cutting-edge developments, the article aims to contribute to advancing knowledge in the field and inspire future research directions in the exciting realm of B5G and 6G networks.

In everyday life, the birth of a number of blind people takes place and millions of people are already available. Visually impaired people struggle to walk safely and in- dependently because they have trouble detecting obstacles. In this work, we suggest a novel approach to detecting obstacles utilizing an Arduino UNO board and an ul- trasonic sensor (HC-SR04). The main goal of this research is to increase the mobility and security of blind people in a variety of settings. The suggested system makes use of the HC-SR04 ultrasonic sensor’s capability to precisely measure distance and identify nearby obstructions. As the main processor component, the Arduino UNO board processes algorithms for real-time obstacle detection while also collecting data from the sensor. The device is intended to give the visually impaired user immedi- ate aural input while informing them of the location and proximity of obstacles. To Extensive testing is done in controlled and real-world settings to assess the system’s performance and dependability. In the studies, the effectiveness of obstacle detec- tion, the system’s response time, and its practicality and usefulness for blind people are all measured. The findings show that the suggested obstacle detection method provides very accurate obstacle identification at a safe distance. Users who are blind or visually handicapped may successfully understand their surroundings thanks to the aural feedback system, which helps them to navigate by making judgments that are well-informed. Additionally, the system responds quickly, guaranteeing that the user receives real-time obstacle updates to increase safety and confidence while mov- ing. The study’s conclusions demonstrate the possibility of using the Arduino UNO board with the HC-SR04 ultrasonic sensor as a practical and affordable approach for detecting obstacles.

Multi-level shaking table tests were performed on 1:3 reduced scale two-story RC IMRF frames conforming to ACI-318-19. The exterior joints lacked shear reinforcement to assess the viability of the ACI model recommended for determining the design shear strength of the beam-column joint panel. The Northridge-1994 earthquake accelerogram was input to the frame for multi-level shaking table testing. Plastic hinges developed in beams under base input motion with a maximum acceleration equal to 0.40g. The exterior joints incurred extensive damage under base input motion with a maximum acceleration equal to 0.70g. The frame achieved displacement ductility and overstrength factors equal to 2.40 and 2.50 respectively. This gives a response modification factor equal to 6. The satisfactory performance of the frame is attributed to the high efficiency of the beam-column joint, which was confined by spandrel beams on two faces, and the high strength of the concrete. The inherent minimal confinement is sufficient to ensure good seismic behavior. The analysis confirmed overstrength equal to 1.58 for joint shear strength in comparison to the design strength determined using the ACI model. The data might serve as a reference for calibrating and validating numerical modeling techniques for performance evaluation, which are crucial in the context of performance-based engineering.

The coronavirus COVID-19 epidemic has wreaked havoc on inhabitants of earth killing thousands of humans from more than 150 countries. The epidemic has put a number of countries under complete lockdown and the deadly situation is still prevailing around the globe. Vaccines have been long known as the most effective means of preventing viral infections. However, the lack of vaccines against COVID-19 has further worsened the situation. In this time of health crisis, it is the duty of scientific research community to provide alternative, effective and affordable strategies to vaccinate human bodies against viral infections-COVID-19 based on focused experimental approaches. Growing evidence suggests that certain natural foods and lifestyle changes have potential to optimize immune functions against viral infections including improving defense function, resistance towards invading pathogens, while maintaining self-tolerance. Boosting immune system gives an edge in fending off viruses and staying healthy. This review presents the six smart steps to add to your to-do list which let the inner work of immunity take place against viral infections-COVID-19 by dissolving the powers of disease and illness. Many of these factors are associated in their functions to improve or properly maintain the immune function such as promoting anti-inflammatory functions, inhibiting pro-inflammatory mediators, modulating cell-mediated immunity, altering the antigen-presenting cellular functions as well as promoting communication between the innate and adaptive immune responses. Thus, a scientific illustration of boosting the immune system by proper sleep, moderate exercise, avoiding stress, utilizing vitamins enriched foods, intake of more water and use of fruits and vegetables will hopefully help the community to deal with the coronavirus by vaccinating the human systems naturally.

The governance of public sector infrastructure projects became an important topic of interest in the project, programme and portfolio management literature during the last decade. Today, it is becoming a central focus for policymakers seeking to ensure success in selecting, designing and implementing government-sponsored programme of multi-projects. Due to the multiple underlying risks and complexities, the governance of infrastructure programme constitutes a critical element in strategic planning in developing countries. This paper has analyzed infrastructure development programme and revealed shortcomings in the areas of appraisal, decision-making, quality assurance and stakeholder management. Approaches to remedy these shortcomings have been proposed.

Nowadays, more than 180 million people believe that the Holy Qur'an was sent by the Almighty Allah through Prophet Muhammad in 610-632 A.D in Mecca and Medina. However, the word Mecca (Q: 48:24) is mentioned only once in the entire Holy Qur'an, which is not related to the birth of the Prophet or any worship. Conventional Islam is mostly based on the hearsay of some Islamic narrators published in the eighth and ninth centuries. To think deeply and conduct research on the verses of the Holy Quran has been mentioned (special urge) directly and indirectly by this Holy Scripture itself many times but it would not be wrong to say that there is no scholarship on the verses of the Quran based on the research method described in the Holy Quran until the present century. Therefore, this paper has been dared to carry out by combining the methods of research followed in the Holy Quran and the academically accepted research methodology. The analysis shows that the results of almost fourteen hundred years of mythological history of conventional Islamic narrators are opposites. First of all, the proper name of the Prophet revealed by the Holy Quran is Ahmed, but Muhammad is an adjective and there are many such names. Secondly, this prophet was not born in Mecca, KSA, nor in 570/571 A.D, but in the Beqaa Valley of Lebanon, between the third and fourth centuries. Thirdly, the Muslim Hajj (pilgrimage) of Mecca is celebrated entirely according to the Lahwal Hadith (idle tales) (Q: 31:6) in the language of the Holy Quran. Originally the place designated for pilgrimage was in the Beqaa Valley, Lebanon. This article will have a double influence on the Muslim world, that is, Islamic scholars will think again deeply and research new ways of scholarship of the Holy Quran, instead of based on the hearsay of idle tales (Lahwal Hadith). On the contrary, those who are stubborn Islamic narrators, since they have already rejected the Holy Quran, will not hesitate to violently attack the researchers and they will not be positively motivated by this paper. This article specifically urges Islamic scholars to conduct in-depth studies on the most important issues of Islam using the Holy Quranic research method.

Irrigation water management components evaluation is mandatory for sustainable irrigated agriculture production in the era of water scarcity. In this research spatio-temporal distribution of irrigation water components were evaluated at canal command area in Indus Basin Irrigation System (IBIS) using remote sensing based geo-informatics approach. Satellite derived MODIS product-based Surface Energy Balance Algorithm for Land (SEBAL) was used for the estimation of the Actual Evapotranspiration (ETa). Satellite derived SEBAL based ETa was calibrated and validated using the ground data-based advection aridity method (AA). Statistical analysis of the SEBAL based ETa and AA shows the mean 87.1 mm and 47.9 mm and, 100 mm and 77 mm, Standard deviation of 27.7 mm and 15.9 mm and, 34.9 mm and 16.1 mm, R of 0.93 and 0.94, NSE of 0.72 and 0.85, PBIASE -12.9 and -4.4, RMSE 34.9 and 5.76 for the Kharif and Rabi season, respectively. Rainfall data was acquired from the Tropical Rainfall Measuring Mission (TRMM). TRMM based rainfall was calibrated with the point observatory data of the Pakistan Metrological Department Stations. Canal water data was collected from the Punjab Irrigation department for the assessment of canal water availability. Water The water balance approach was applied in the unsaturated zone for the quantification of the gross and net Groundwater irrigation. Mmonthly variation of ETa with the minimum average value of 63.3 mm in January and the maximum average value of 110.6 mm in August was found. While, the average annual of four cropping years (2011-12 to 2014-15) ETa was found 899 mm. Average of the sum of Net Canal Water Use (NCWU) and Rainfall during the study period of four years was only 548 mm (36% of ETa) and this resulted the 739.6 mm of groundwater extraction. While the annual based variation in groundwater extraction of 632 mm and 780 mm was found. Seasonal analysis revealed 39% and 61% of groundwater extraction proportion during Rabi and Kharif season, respectively. The variation in four cropping year’s monthly groundwater extraction was found 28.7 mm to 120.3 mm. This variation was high in the 2011-12 to 2012-13 cropping year (0 mm to 148.7 mm), dependent upon the occurrence of rainfall and crop phenology. Net groundwater irrigation, estimated after incorporating the efficiencies was 503 mm year-1 on average for the four cropping years.

Remote sensing technology is crucial for accurate rooftop detection, benefiting urban planning, disaster management, and solar resource estimation. This study employs Efficient Interactive Segmentation (EISEG) to enhance the efficiency of remote sensing image labeling, with a particular focus on rooftop detection. It is necessary to use modern technology because traditional manual labelling methods are labor-intensive and complicated. The study introduces a novel framework on deep learning semantic segmentation models, facilitating an efficient approach to rooftop identification using high-resolution UAV remote sensing datasets. Large dataset of labeled UAV rooftop building images, in which each superpixel region is assigned a binary label indicating rooftop presence. Advanced methods including Asymmetric Neural Network (ANN), Dual At-tention Network (DANet), PP-LiteSeg, and Deeplab3 are implemented for automatic rooftop detection due to their higher performance and advanced architectures. These models are executed on the Baidu deep learning platform PaddlePaddle, generating initial rooftop segmentation maps crucial for estimating photovoltaic resources. The ANN model emerges with the highest accuracy at 96%, followed by DANet at 95.09%, PP-LiteSeg at 94.54%, and Deeplab3 at 81.61%. The outcomes presenting efficient models for automated rooftop identification, and demonstrating the continuous need for improving deep learning techniques in smart and sustainable cities.

In general, remote sensing has proven to be a powerful tool in the overall understanding of natural and anthropogenic phenomena. Satellites have become useful tools for tasks such as characterization, monitoring, and the continuous prospecting of natural resources. This research aims to analyze spatial dynamic and destructive on coral reefs area and correlation between live coral reduction and population on small islands. Landsat MSS, TM, ETM, and OLI-TIRS are used to spatial analyze of coral reef dynamics from 1972 to 2016. The image processing includes gap-filling, atmospheric correction, geometric correction, image composite (true color), water column correction, unsupervised classification, reclassification, accuracy assessment. The statistical analysis identifies the relationship between dynamic population data with a reduction of live coral, namely Principal Component Analysis (PCA) and Multiple Regression Analysis. The effect of the population shows a positive correlation with the reduction in the area of live coral, although it is significant. The fact is the practice of coral destruction on an island; it is usually not only caused or carried out by residents who live on the island but also carried out by other residents of different islands.

The OPV is the vaccine of choice in polio eradication, especially in developing countries, as it has eliminated the wild poliovirus type 2. However, the immunity induced by IPV is better than that induced by the OPV. The present study compared the mucosal and humoral response to poliovirus vaccines administered to previously OPV-immunized children to assess the immunity gap in children at-risk of high poliovirus transmission. This was a community-based three-arm cluster randomized controlled trial conducted from June 2013 to May 2014 in healthy children under five years of age living in three high-risk districts of Pakistan, i.e., Karachi, Kashmore, and Bajaur. 387 clusters were randomized (131 to arm A, 127 to arm B, and 129 to arm C); however, 360 remained in the trial until the end (116 in arm A, 122 in arm B, and 122 in arm C). These clusters were randomly allocated using a computer algorithm to receive routine polio program (bOPV) activities (control, arm A), additional interventions with community mobilization and provision of short-term preventive maternal and child health services and routine immunization, including bOPV via health camps, (arm B), or all interventions of arm B with an additional provision of IPV (arm C ~ bOPV and IPV). Blood and stool samples were collected from a sub-sample to estimate humoral and intestinal immunity. Study findings showed that the serum titers were highest in Group C (IPV+OPV) at the baseline for P1, where its increase over time was also more prominent. Titers for P2 and P3 were statistically significantly higher amongst those who had received a routine OPV dose versus those who had not; this was true for all study groups and visits. In populations with high Oral Polio Vaccine (OPV) failure rates, administering an Inactivated Polio Vaccine (IPV) booster after a minimum of two OPV doses may effectively bridge immunity gaps. The IPV alone offers limited benefits to humoral immunity and doesn't provide intestinal immunity to prevent the infection and propagation of live poliovirus among unexposed populations.

Chemical fertilizers are commonly used to meet the nutritional demands of the crops and boost their yield. However, their high costs and excessive application in soils increases the cost of production and have negative effects on the soil and environmental health. Vermicompost is an organic amendment that can potentially lessen the dependence on chemical fertilizers with additional advantages of sustainable nutrient supply to crops and maintaining soil health. To evaluate the potential of two diverse vermicomposts, sole and combined application of these vermicomposts with reduced rates of chemical fertilizers were used for tomato cultivation in a field study. The results indicated that vermicompost produced from cow dung combined with chemical fertilizers proved to be more effective in improving tomatoes' growth, physiology, yield and nutritional attributes. Combined application of vermicompost and chemical fertilizer significantly improved root length (21.6%), plant height (167%), SPAD value (13.5%),chlorophyll 'a' (96%), chlorophyll 'b' (161%), relative water content (16%), membrane stability index (18%), carotenoid (87%), yield (82%), photosynthetic rate (148%), and fruit diameter (83%) protein (89%), fat (27.5%), fiber (12%), vitamin C (52%), calcium (54%), magnesium (117%), phosphorus (38%), potassium (128%), as compared to control treatment (NP applied). In addition, significant improvements in different soil physico-chemical properties were also pragmatic. The results suggest that vermicompost application with reduced doses of chemical fertilizers can be used to improve crop yield and soil physico-chemical properties.

Validation and verification are the critical requirements in the knowledge acquisition method for the clinical decision support system (CDSS). After acquiring the medical knowledge from diverse sources, the rigorous validation and formal verification process are required before creating the final knowledge model. Previously, we have proposed a hybrid knowledge acquisition method for acquiring medical knowledge from clinical practice guidelines (CPGs) and patient data in the Smart CDSS for treatment of oral cavity cancer. The final knowledge model was created by combining knowledge models obtained from CPGs and patient data after passing through a rigorous validation process. However, detailed analysis shows that due to lack of formal verification process, it involves various inconsistencies in knowledge relevant to the formalism of knowledge, conformance to CPGs, quality of knowledge, and complexities of knowledge acquisition artifacts. Therefore, it is required to enhance a hybrid knowledge acquisition method that thwarts the inconsistencies using formal verification. This paper presents the verification process using the Z formal method and its outcome as an enhanced acquisition method – known as the refined knowledge acquisition (ReKA) method. The ReKA method adopted verification method and explored the mechanism of theorem proving using the Z notation. It enables to identify inconsistencies in the validation process used for hybrid knowledge acquisition. Additionally, it refines the hybrid knowledge acquisition method by discovering the missing steps in the current validation process at the acquisition stage. Consequently, ReKA adds a set of nine additional criteria to be used to have a final valid refined clinical knowledge model. The criteria ensure the validity of final knowledge model concerning formalism of knowledge, conformance to GPGs, quality of the knowledge, usage of stringent conditions and treatment plans, and inconsistencies possibly resulting from the complexities. Evaluation, using four medical knowledge acquisition scenarios, shows that newly added knowledge in CDSS due to the addition of criteria by ReKA method always produces a valid knowledge model. The final knowledge model was also evaluated with 1229 oral cavity patient cases, which outperformed with an accuracy of 72.57\% compared to a similar approach with an accuracy of 69.7\%. Furthermore, ReKA method identified a set of decision paths (about 47.8%) in the existing approach, which results in a final knowledge model with low quality, non-conformed from standard CPGs. In conclusion, ReKA is formally proved method which always yields valid knowledge model having high quality, supporting local practices, and influenced from standard guidelines.

In recent years, the digital economy has played an increasingly important role in enhancing productivity, fostering growth, and facilitating the emergence of digital banking. With the widespread adoption of digital financial services for financial inclusion, the banking sector is experiencing a demand for digital transformation. It is important to note that despite the many advantages of this change, it also disrupts the familiar banking experience that customers have grown to expect, as well as introducing potential risks to maintaining customer protection at previous levels. Many critics have raised concerns regarding customer protection and potential exposure to various risks that may arise from digital financial services, which may result in both financial and non-financial losses. These risks can impact customer retention as dissatisfied customers may switch to alternative service providers. Additionally, reputation can be affected since merely offering digital financial services may not sufficiently safeguard customers. To remain competitive, financial institutions must deliver a secure experience that aligns with customer expectations while considering economic factors and societal needs. This is why it is essential to comprehend the severity of the risk factors that influence the protection of customers in the realm of digitalized banking services and products. In this study, five factors have been identified that influence customer protection when using digital financial services in Pakistan. Based on the analysis conducted using SmartPLS, it appears that all the factors proposed in this study have a significant and positive impact on the protection of customers. In particular, the information provided remains of paramount importance when it comes to determining the level of protection that a customer is entitled to within digital financial services, followed by responsiveness, privacy, authentication, and encryption mechanisms. Due to these findings, the implementation of enhanced information security management principles becomes imperative for the development and progress of the Pakistani digital banking industry.

Danyore Valley area is a new prospect of copper-gold mineralization in the Gilgit-Baltistan province, Kohistan terrane, northern Pakistan. The mineralization is Cu-Au vein-type, localized within quartz veins and controlled by a fracture system mainly trending NW and NE. The host units belong to the Ladakh-Kohistan arc terrane, which covers northern Pakistan and north-western India and mainly comprises Precambrian basement units, Paleozoic to Cenozoic magmatic rocks, and sedimentary strata. The mineralized wall rocks consist of Mesozoic gabbro and diorite, which have undergone an intensive hydrothermal alteration. The study area, Danyore Valley, has yet to be explored. The geological background and mineralization type in literature are scarce. Moreover, the tectonic setting, petrogenesis, age, and magmatic evolution of the gabbro-diorite hosting unit still need to be better understood. Furthermore, the sources of metals and mineralized fluids and the types of mineralization and alteration are also unexplored. This research's contribution presents the field investigation, microscopic observations, whole rock geochemistry (major, trace, and REE), mineral analysis (EPMA), in situ LA–ICP–MS zircon U–Pb age dating, and zircon trace elements data for Danyore Valley Cu-Au prospect of Kohistan Batholith. The current research work's objectives are to (a) constrain the emplacement ages of the Danyore Valley host rocks, (b) determine the petrogenesis and tectonic environment of the gabbro-diorite wall rocks, and (c) identify the mineralization style and alteration patterns of Cu-Au occurrences. The U-Pb isotopic data of studied zircons from Danyore Valley diorite specimens yielded concordia ages from 111.60 ± 0.90 Ma to 112.18 ± 0.74 Ma. Correspondingly, the gabbro rock sample displayed a concordia age of 110.21 ± 0.99 Ma, indicating the crystallization time of the host bodies is mainly the early cretaceous period (∼110 Ma). The findings of this study reveal that the calc-alkaline affinity and arc-like geochemical characteristics of the gabbro and diorite rocks have been characterized by a significant enrichment in large-ion lithophile elements and an apparent depletion in high-field strength elements. The parent magma probably originated from a partial melting process of mantle depletion, and geochemical traits are characteristic of magmas associated with subduction zones. The Danyore Valley area of Kohistan terrane is defined by the existence of several mineralized quartz veins, which are mainly sulfide assemblages. The sulfide ore is mainly comprised of chalcopyrite, pyrite, and bornite, with a smaller amount of covellite and sphalerite and significant traces of gold, which are distributed mainly in sulfides. Copper and gold mineralization of Danyore Valley is associated with phyllic, propylitic, and carbonatization alteration assemblages. Metal-rich quartz veins exhibit a spatial correlation with diorite and gabbro rocks. The discovery of several surface Cu-Au vein-type mineralized areas accompanying outcrops of copper supergene enrichment at the Danyore Valley prospect is significant evidence (predictor patterns) of porphyry-style deposits in the Gilgit district, Kohistan terrane, northern Pakistan. This work also advocates the importance of the Danyore Valley prospect and Kohistan Batholith region for further detailed geological studies.

In the field of 2-D image processing and computer vision, accurately detecting and segmenting objects in scenarios where they overlap or are obscured remains a challenge. This difficulty is worse in the analysis of shoeprints used in forensic investigations because they are embedded in noisy environments such as the ground and can be indistinct. Traditional Convolutional Neural Networks (CNNs), despite their success in various image analysis tasks, struggle with accurately delineating overlapping objects due to the complexity of segmenting intertwined textures and boundaries against a background of noise. This study introduces employs the YOLO (You Only Look Once) model enhanced by edge detection and image segmentation techniques to improve the detection of overlapping shoeprints. By focusing on the critical boundary information between shoeprint textures and the ground, our method demonstrates improvements in sensitivity and precision, achieving confidence levels above 85% for minimally overlapped images and maintaining above 70% for extensively overlapped instances. Heatmaps of convolution layers were generated to show how the network converges towards successful detection using these enhancements. This research may provide a potential methodology for addressing the broader challenge of detecting multiple overlapping objects against noisy backgrounds.

Selenium and iodine are essential micronutrients for humans. They are often deficient in food supply due to low phytoavailable concentrations in soil. Agronomic biofortification of food crops is one approach to overcome micronutrient malnutrition. This study focused on German consumers’ willingness to purchase selenium- and/or iodine-biofortified apples. For this purpose, an online survey was carried out. In this context, consumers were asked to choose their most preferred apple product from a set card of product alternatives (Discrete Choice Experiment). The multinomial logit model results demonstrated that German consumers’ have a preference in particular for iodine-biofortified apples. Furthermore, apple choice was mainly influenced by price, health claims, and plastic-free packaging material. Viewed individually, selenium did not exert an effect on product choice whereas positive interactions between both micronutrients exist.

Drought stress is a major production constraint in crops globally. Crop wild relatives are important source of resistance and tolerance for both biotic and abiotic stresses, respectively. A breeding program was initiated to introgress drought tolerance in sunflower through hybridization between the wild species Helianthus argophyllus and the cultigen pool of H. annuus. Selection was carried out in the F2 to F5 segregating populations for high cuticular waxes, smaller leaf area, single heading and high oil content. The selected F5 breeding lines were compared with non-adapted elite sunflower germplasm in a replicated randomized complete block research project using different water treatments comparing fully irrigated (T0), with 75 (T1), 50 (T2) and 25% (T3) irrigation treatments. The comparison between the two types of germplasm showed that drought tolerant breeding lines had comparatively lesser decreases in leaf area, shoot weight and root shoot ratio 10 under the various drought treatments. Leaf area of the drought selected F5 lines were smaller than that of the elite germplasm under controlled irrigated treatments, but they maintained their leaf area under the drought treatments. Several drought resistant promising lines D-2, D-5, and D-27 were identified and showed high leaf area, great root length and increase root to shoot ratio under the highest stressed treatments (T3). Some of the lines could be directly used for the development of drought tolerant hybrids. Combining ability test indicated D-27 (F7) as good general combiner for seed yield plant−1 and oil contents when mated with male line RSIN.82. These hybrids could help to minimize seed yield losses due to water stress and to achieve profitable cultivation of sunflower in 18 arid regions of Pakistan.

In recent years, the application of Indoor Positioning Systems (IPS) has experienced a significant increase in demand, with the aging of the world’s population and their changing lifestyles. While outdoor positioning systems, such as the Global Positioning System (GPS), have significantly advanced over the years, indoor positioning has been restrained by the limitations of the employed technologies. This paper presents a hybrid wireless positioning system able to locate wearables indoor accurately. It is based on the Wi-Fi and Bluetooth technologies, by using trilateration to determine the position of Bluetooth low energy (BLE) wearable devices with an accuracy of up to 1.8 meters. A graphical user interface (GUI) was used to illustrate the performance of the proposed systems, by allowing users to visualize the captured data in two dimensions and three- dimensions in real-time.

Laminitis is considered as an important underlying cause of lameness diseases, yet its specific pathogenesis remains unclear. Autophagy is an intracellular degradation mechanism that controls recycling of membrane-associated integrin and may aid in the progression of metabolic diseases. But the significance of autophagy for initiation and development of laminitis is unknown. The present study aimed to explore autophagy activity in the laminar tissue of dairy cows with oligofructose-induced laminitis. Twelve healthy non-pregnant Holstein cows were randomly divided to 2 groups of 6 cows each, entitled the control group and the oligofructose overload group (OF group), respectively. At 0 h, cows in OF group were gavaged with oligofructose (17 g/kg BW) dissolved in warm deionized water (20 mL/kg BW) through oral rumen tube, and dairy cows in control group were gavaged with the same volume of deionized water by the same method. At -72 h before perfusion as well as 0 h, 6 h, 12 h, 18 h, 24 h, 36 h, 48 h, 60 h, and 72 h after perfusion, clinical evaluations in both groups were monitored. After 72 h, laminar tissues of dairy cows in both groups were collected to examine genes and proteins. We found the significantly higher (P<0.05) levels of mRNA ATG5, ATG12, and Becilin1, but P62 and mTOR were extensively lower (P<0.01) in the laminar tissue of the OF group than the control group. Protein expression level of Becilin-1 was higher significantly (P<0.05), and the protein expression level of LC3II was lower significantly (P<0.05) in OF group than control group. However, the expression of P62 reduced (P>0.05) non-significantly in OF group than control group. The distribution of Beclin1 protein in laminar tissue increased (P<0.01) significantly, and distribution of P62 protein decreased (P<0.05) significantly in OF group than control group. In conclusion, laminar tissue damage occurred during the onset of laminitis, which promoted the occurrence of autophagy, and confirmed that autophagy was involved in the regulation and pathogenesis of laminitis in dairy cows.

One of the most important component of a Geographic Information Retrieval (GIR) is the geoparser, which performs toponym recognition, disambiguation, and geographic coordinate resolution from unstructured text domain. However, news articles which report several events across many place references mentioned in the document is not yet adequately modeled by regular geoparser types where the scope of resolution is either on toponym-level or document-level. The capacity to detect multiple events, geolocate its true locations and coordinates along with their numerical arguments are still missing from modern geoparsers, much less in Indonesian news corpora domain. We propose a novel type event geoparser which integrates an ACE-based event extraction model and provides precise event-level scope resolution. The geoparser casts the geotagging and event extraction as sequence labeling and uses Conditional Random Field with keywords feature obtained using Aggregated Topic Model as a semantic exploration from large corpus, which eventually increases the generalizability of the model. The geoparser also use Smallest Administrative Level feature along with Spatial Minimality-derived algorithm to improve the identification of Pseudo-location entities, resulting 19.4% increase for weighted F1 score. As a side effect of event extraction, the geoparser also extracts various numerical arguments and able to generate thematic choropleth map from a single news story.

This study was to designed to develop sorafenib-loaded polymeric nanoparticles, surface-modified with pluronic F-127 for the effective treatment of hepatocellular (HCC) and renal cell carcinomas (RCC). Poly lactic coglycolic acid (PLGA) was used to encapsulate different concentrations of sorafenib by a simple modified solvent evaporation method applying pluronic F-127 as a surfactant and coating agent. The preformulation and characterization studies were conducted to evaluate the incompatibilities among sorafenib, PLGA and pluronic F-127, and physicochemical properties of the formulations, respectively. The sizes of the coated and plain PLGA nanoparticles were ~140 ± 14.7 nm and ~ 120 ± 10.1 nm, respectively. It has been confirmed from the in vitro release studies that PLGA sustained the release of sorafenib, avoiding the initial burst release, while the in vivo studies demonstared that surface-modified nanoparticles have greater affinity in the target aorgans than plain PLGA nanoparticles and free drug keeping the dose constant (20 mg/kg body weight). The delivery of sorafenib-loaded polymeric PLGA nanoparticles into the target tissues and their pharmacokinetic parameters have been improved significantly compared to the reported formulations.

Pakistan is one of the few countries where poliovirus transmission still persists, despite intensive efforts to eradicate the disease. Adequate vaccination coverage is essential to achieve polio eradication, but misconceptions about polio vaccines have hindered vaccination efforts. To address this issue, we conducted a mixed-methods study to explore knowledge and perceptions regarding polio disease and immunization in high-risk areas of Pakistan. We collected quantitative data from 3780, 1258, and 2100 households in Karachi, Bajaur, and Pishin, respectively, and supplemented this with qualitative data from focus group discussions and in-depth interviews. Our findings reveal a high level of awareness about polio and its immunization; however, misperceptions about the polio vaccine persist, leading to vaccine refusal for both polio and routine immunization. Our study provides up-to-date data on knowledge and perceptions of polio and its immunization and identifies critical gaps. These findings can inform the development of future strategies and innovative approaches to improve the success of the polio program in Pakistan.

Self-adaptive systems are capable of reconfiguring themselves while in use to reduce the risks forced by environments for which they may not have been specifically designed. Run-time validation techniques are required because complex Self-adaptive systems must consistently offer acceptable behavior for important services. The run-time testing can offer further confidence that a Self-adaptive system will continue to act as intended even when operating in unknowable circumstances. This article introduces an evolutionary framework that supports adaptive testing for Self-adaptive systems. To ensure that the adaptive systems continue to operate following its requirements and that both test plans and test cases continuously stay relevant to shifting operational conditions. The proposed approach using the SPEA2 algorithm facilitates both the execution and adaptation of run-time testing operations.

Currently, software development is more associated with families of configurable software rather than the single implementation of a product. Due to the numerous possible combinations in a software product line, testing these families of software product lines (SPLs) is a difficult undertaking (SPL). Moreover, the presence of optional features makes the testing of SPLs impractical. Several features are presented in SPLs, but due to the environment's time and financial constraints, these features are rendered unfeasible. Testing subsets of configured products is thus one approach to solving this issue. In order to reduce testing effort and get better results, alternative methods of testing SPLs are required, such as the combinatorial interaction testing (CIT) technique. Unfortunately CIT method produces unscalable solutions for large size SPLs with excessive constraints. The CIT method costs more because of feature combinations. The optimization of the various conflicting testing objectives, such as reducing the cost and configuration number, have also been considered. In this article, we have proposed a search-based software engineering solution using multi-objective optimization algorithms (MOEAs). In particular, the research is applied to different types of MOEA methods; Indicator-Based Evolutionary Algorithm (IBEA), Multi-objective Evolutionary Algorithm based on Decomposition (MOEA/D), Non-Dominated Sorting Genetic Algorithm II (NSGAII), NSGAIII, and Strength Pareto Evolutionary Algorithm 2 (SPEA2). The results of the algorithms are examined in the context of distinct objectives and two quality indicators. The results revealed how feature model attributes, implementation context and the number of objectives affect the performance of the algorithms.

The experience of ego dissolution and self-transcendence induced by psychedelic substances offers a profound challenge to our conventional understanding of the self and our relationship with the natural world. This paper delves into the philosophical underpinnings and implications of this phenomenon, exploring how the temporary breakdown of ego boundaries during a psychedelic experience may foster a sense of profound interconnectedness with nature. Drawing from Western and Eastern philosophical traditions, as well as recent insights from neuroscience and consciousness studies, we examine the potential of psychedelic-induced self-transcendence to catalyze a shift in our perspectives on the human-nature relationship. The paper investigates the philosophical implications of this experience, including its resonance with deep ecological philosophies and its potential to inspire more ecocentric ethical frameworks. Furthermore, we explore the possible practical implications of fostering a sense of ecological connectedness through psychedelics, such as promoting environmentally sustainable behaviors and addressing the pressing challenges of climate change and ecological degradation. Ultimately, this exploration highlights the value of engaging with altered states of consciousness as a means to reconsider our place within the intricate web of life on Earth.

The aim of the current study was to develop and evaluate the therapeutic potential of apocynin (APO) loaded pH-sensitive nanoparticles (NPs) based transdermal hydrogel for management of rheumatoid arthritis (RA). Slightly modified nanoprecipitation technique was used for preparation of polymeric nanoparticles. Optimization was done through design expert software. Optimized APO-NPs were loaded into carbopol-934 based hydrogel as final dosage form and further studied for physicochemical properties. Optimized APO-NPs formulation had a minimum particle size 63.44 nm, polydisperibility index 0.161, and zeta potential -15mV with a maximum encapsulation efficiency of 89%. In-vitro and ex-vivo studies of APO-NPs based hydrogel was performed at pH 5.5 (pH of normal skin) and 6.8 (pH of inflammed joint) showed a pH-responsive sustained drug release and increased penetration in comparison to free APO based hydrogel. The stability studies of APO-NPs based hydrogel were done to strengthen the potential use of the prepared formulation through transdermal route. Assessment and therapeutic efficacy of the prepared pH-sensitive nanocarriers system was evaluated in chronic inflammatory RA mice model. Parameters associated with chronic inflammation were investigated including behavioral changes and histopathological, and radiological x-rays images of joints of mice paws. In-vivo study depicts improvement in behavioral parameter, decline in synovial hyperplasia and bone structure restoration. In conclusion, APO loaded pH-sensitive NPs based transdermal is a promising carrier system that can effectively manage RA.

In the present study, a simple approximation expression is given for the relationship between the period and amplitude of a simple pendulum under magnetic action. The analytical solution presented for the given problem. Two numerical quadrature methods Simpson's and Boole's method were utilized to demonstrate a new approximation of the problem. The results of the numerical quadrature have been compared to the exact solution. Absolute and relative mistakes of the problem have been presented. The Matlab program 2013R has created a numerical method that is used to analyze the outcome, It has been determined that the comparison's outcomes attest to the method's suitability and correctness. Moreover, the results show that numerical solution is suitable for the problem.

Study aimed to evaluate the impact of integrating family planning with maternal, newborn, and child health (FP-MNCH) on uptake of modern contraceptive methods and related health outcomes in two districts of the province of Sindh, Pakistan. Impact of intervention was evaluated using a quasi-experimental control before-after study design. Intervention included capacity building of healthcare providers and outreach workers, ensuring sustained supplies of family planning commodities, data-driven decision-making, and community engagement activities. Data was collected through household surveys at baseline (December2020) and endline (December 2022). The sample size was estimated as 880 married women of reproductive age (MWRA) in each district. The Difference and Difference(DiD) analytical method was used to estimate the impact of intervention adjusted for potential confounding factors. There was statistically significant increase of 11.3% in the current use of MCM in the intervention group compared to the control group (p value <0.001), with increases observed in the uptake of injection , implants, and condoms. Additionally, there was an increase in the proportion of women who had ANC visits (DiD 10.5% p value 0.003), FP counselling during ANC (DiD 15.6% p value < 0.001), LHW visits during pregnancy (DiD 15.1% p value 0.021), PNC check-ups for mother (DiD 25.2% p value <0.001), LHW visits after delivery (DiD 20.4% p value <0.001), and LHW advised for family planning at PNC visit n (DiD 14.5% p value 0.030). This study provides strong evidence for the scaling-up of integrated interventions through existing health care platforms utilizing human resources deployed by the government. This FP-MNCH model has the potential to be adopted in other provinces and at federally administered areas for both health and population planning. This model should be considered for replication in other districts of Sindh to accelerate current level of integration already existing.

Monkeypox virus belongs to the Orthopoxvirus genus, which belongs to the Poxviridae family. The Monkeypox virus is responsible to cause monkeypox, a developing zoonotic disease that has been identified as the most common orthopoxvirus infection in humans in the post-eradication era of smallpox. The virus can be transmitted by a variety of animals, including monkeys and rodents as well as person-to-person. Monkeypox has a clinical presentation that is quite similar to smallpox but mortality is low, in that the febrile prodrome is followed by a period of skin eruption. Monkeypox cases have extended outside the forests of central Africa, where they were first discovered, to other regions of the globe, where they have been imported. This pattern of transmission is most likely related to a global reduction in orthopoxvirus immunity following the discontinuation of smallpox vaccination in 1980, when smallpox was proclaimed eliminated. As a result, monkeypox might become the very common orthopoxvirus infection that affect humans. The emergence of epidemics outside of Africa emphasizes the disease's global significance. Increased monitoring and identification of monkeypox cases are critical tools for gaining a better knowledge of the disease's ever-changing epidemiology.

Coinfection of B virus (HBV) and hepatitis Delta virus (HDV) lead to severe forms of progressive liver diseases. However, commercially available antiviral drugs have shown considerable adverse effects and low efficacy in managing these patients. Thus, there is a pressing need to develop new, innovative, and evidence-based therapies for these pathological entities. In line with this, some investigators have attempted to develop anti-viral drugs targeting HBV/HDV coinfection. In another development, investigators have also attempted to establish immune therapy targeting for HBV infection as recovery or effective control of HBV infection also lead to efficient control of HDV infection. This review has discussed an account of the evolving antiviral and immune therapeutic drugs for HBV/HDV infection. Also, based on current scientific knowledge how we have described the pros and cons of these drugs as no suitable drug has been developed during the last forty years for treating HBV infection except the availability of two” repurposed drugs”; interferons and its derivatives and nucleoside analogs, for managing HBV or HBV/HDV coinfection. It seems that an evolving and innovative therapeutic regimen that combines both antiviral drugs and immune modulators may be the best and realistic option for management of HBV/HDV coinfection.

Hydrogels can provide instant relief to pain and facilitate the fast recovery of wounds. Currently the incorporation of medicinal herbs/plants in polymer matrix is being investigated due to their anti-bacterial and wound healing properties. Herein, we investigated the novel combination of chitosan (CS), chondroitin sulfate (CHI) and garlic (Gar) to synthesize hydrogels through freeze gelation process for faster wound healing and resistance to microbial growth at the wound surface. The synthesized hydrogels were characterized via Fourier transform infrared spectroscopy (FTIR), which confirmed the presence of relevant functional groups. The scanning electron microscopy (SEM) images exhibited the porous structure of the hydrogels, which is useful for the sustained release of Gar from the hydrogels. The synthesized hydrogels showed significant inhibition zones against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). Furthermore, cell culture studies confirmed the cyto-compatibility of the synthesized hydrogels. Thus, the novel hydrogels presented in this study can offer antibacterial effect during wound healing and promote tissue regeneration.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

While microcredits are, by the development practitioners, repeatedly hailed as a useful measure of development policy, this empirical research in Bangladesh arrives at different results: the governing and disciplinary measures are necessary to trigger the best possible repayment success. Based on interviews with the microfinance beneficiaries, loan officers, and microfinance experts in Bangladesh, I chart some of the most frequently used governing and disciplinary techniques including fictitious proximity of loan officers, their fields of visibility and surveillance processes. The “success” of credit delivery is a neoliberal stance that ensures the ceaseless debt repayment process using the intentional and planned conduct, capitalizing social capital and credit honour reputation, surveillance over business enterprises, use of equivocal language and different forms of deception. The development strategy through microfinance in Bangladesh is a development “dispositif” with a changing shift in its declared social missions.

The rapid advancement of technology has revolutionized language learning, introducing innovative methods that depart from traditional instructional approaches. This study employs a mixed-methods research design to examine the impact of chatbot-based language learning support, adaptive learning algorithms, and virtual reality language immersion on the language learning proficiency and self-regulated learning skills of English as a Foreign Language (EFL) learners. The research design includes quantitative analysis of language proficiency scores and qualitative exploration of learner experiences with the technological interventions. The theoretical implications of this study are rooted in constructivist and socio-cultural learning theories, which underpin the design and implementation of the technological interventions. The triangulation of qualitative and quantitative data revealed that the participants' positive perceptions of the effectiveness of chatbot-based language learning support were supported by the quantitative results, with the variable "chat-bot based support" demonstrating a substantial mean difference compared to other groups. This convergence of findings reinforces the positive influence of chatbot-based support on language learning outcomes and highlights the importance of integrating theoretical perspectives with empirical evidence to gain a comprehensive understanding of the impact of technological interventions on language learning outcomes for EFL learners. The study's findings provide insights into the potential of these technological interventions to optimize language learning outcomes for EFL learners and promote autonomous learning behaviors.

Introduction: The management performance of hospitals in emergency departments in coping with clinical hazards is necessary for their success in providing quality services. The purpose of this study is to provide an optimization procedure and applying management performance in health and medical emergency on the rate of emergency preparedness of the suburb city hospitals. Research method: A semi-experimental and interventional descriptive study in the emergency department of Shahid Motahari Hospital in 2015-2016. Data was collected through the standard checklist of hospital emergency responsiveness test to WHO disasters with 90 questions in 9 domains which is codified by the World Health Organization, in the form of interviews and observing evidences , and if necessary a numerical analysis. Initially, the situation was measured according to this checklist. In the next stage, a set of solutions was developed and then the solutions were implemented according to the obtained information. Data analysis before and after proposing the procedure and its application in order to improve the quality of health management performance and emergency preparedness was performed using central indices, and for describing and presenting the survey results, tables and graphs were used. Results: The highest and lowest emergency preparedness rates for disasters and emergencies before the proposed procedure were the Communication Factor (%77/8) and Human resource factor (%2/8) respectively. The degree of preparedness of the medical center was measured in the management performance according to the model (WHO) before proposing the procedure (%77.98). The researcher's procedure provided and applied based on the information obtained from survey environment, location and type of hospital structure. After providing the procedure, the maximum and minimum rates were the continuity of service factor (%58.3) and post-accident rebuilding factor (%100), respectively. Generally, the rate of emergency preparedness of studied medical center in management performance for coping with disasters and medical emergencies was measured (%97.2) according to hospital emergency responsiveness test for accidents and (WHO). The significance level is less than 0.05, so we can say that the effectiveness with confidence (95%) was effective. Conclusion: According to the statistics of accidents and disasters in the suburb cities, the results of the research and the importance of the role of emergency departments in interurban hospitals in controlling accidents, the need for planning and implementation of practical measures such as conducting training courses on health management in disasters and emergencies, having an estimate of critical and essential resources, changing the structure, providing manpower (emergency management) in order to more precise control and ease of service, maintenance and repair of equipment, timely triage and retrofitting of hospitals were effective in improving their preparedness.

In this study, I extend the Fama and French five-factor asset pricing model with a sixth factor, namely, carbon risk, to investigate its impact on equity returns. To measure carbon risk, a new factor ‘pollutant minus green,’ is developed using the difference between the weighted average returns of pollutant and green firms across 51 developed and emerging countries across four categories—North America, Europe, Emerging Markets, and the Asia Pacific. The results reveal that North America, Europe, and Asia Pacific markets have a carbon risk premium that gets eliminated in small-cap firms. The carbon risk factor is further tested in left-hand side (LHS) test asset portfolios and found to be more pronounced with size-effect anomaly; specifically, small stock firms report greater declining average returns because of more exposure than the mega-cap stocks to carbon dioxide emissions. Furthermore, size-effect anomaly prevails with profitability and investment factors across firms. Therefore, high profitability, as well as high investment small firms, show a greater decline than the big stock firms in average returns when their carbon dioxide emissions increase. The asset pricing model evaluation is carried out through the Gibbons, Ross, and Shanken test. The six-factor model directed at capturing carbon risk patterns in average equity returns performs better than the three-factor and five-factor models of Fama and French (1993 and 2015) in the majority of categories under 3x3 sorting and compete with both Fama and French model under 2x4x4 sorted LHS portfolios. The finding of this study offers various useful applications for investors, policymakers, brokers, corporations, governmental pollution abatement institutions, and other stakeholders who wish to obtain carbon risk premium.

The rapid development in industries manufacturing plastic bags is taking serious consideration to save the environment and human health, one way or the other. This study examines the composition of degradable and non-degradable plastic bags collected from the markets of different sectors of Islamabad. Hundred samples of both Degradable and non-degradable plastic bags were collected from the open market. The concentrations, proportion, and patterns of different heavy metals (additives) were used in the production of both degradable and non-degradable plastic bags by using the standard method with the help of Hands Held X-Ray Fluorescent (HHXRF) instrument. Samples results of the study showed Titanium, Calcium and Copper used in massive amounts, some of the toxic metals i.e., Arsenic, Lead, Cadmium, Chromium and Mercury were also detected. This study also reveals that degradable plastic bags might be more hazardous than non-degradable plastic bags because due to the Photolytic properties of additives used in degradable plastic bags when the chains of polymers break, the heavy metals are released in environment and become the part of it. So, concern department like Ministry of climate change and Pakistan Environmental Protection Agency should take serious step to control these serious issues.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is a positive sense single stranded RNA genome containing virus which has infected millions of people all over the world particularly China. The virus has been mutating rapidly enough resulting in the emergence of new variants and sub-variants which have reportedly been spread from Wuhan city of China, the epicenter of the virus, to the rest of China and all over the world. The occurrence of mutations in the viral genome especially in the viral spike protein region has resulted in the evolution of multiple variants and sub-variants which gives the virus benefit of host immune evasion and render the modern-day vaccines and therapeutics ineffective. Therefore, there is a continuous need to study the genetic characteristics and evolutionary dynamics of the SARS-CoV-2 variants. Hence, in this study, a total of 833 complete genomes of SARS-CoV-2 variants (including the wild-type or reference sequence) from Taiyuan and Wuhan cities of China were genetically characterized and studies their phylogenetic and evolutionary dynamics using phylogenetics, genetic similarity, and phylogenetic network analysis. Our results show a lot of useful information regarding the evolutionary dynamics of the viral variants, their genetic similarities/dissimilarities, and their phylogenetic relationships. It has been reported in this study that the SARS-CoV-2 variants have nine recombinant events which suggest very important information regarding the viral evolution. In addition, the phylogenetic network analysis shows the number of mutations resulting in emergence and clustering of the viral variants of both cities which reveal significant information regarding the phylodynamics of the virus. This study, to the best of our knowledge, is the first ever genetic comparative study of Taiyuan and Wuhan cities. This study will help better understand the virus, cope with the emergence, and spread of new variants at local level as well as at international level and inform the public health authorities to make better informed decisions in designing new viral vaccines and therapeutics.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

The most frequent, noticeable, and frequent natural calamity in the karakoram region is landslides. Extreme landslides have occurred frequently along Karakoram highway, particularly during the monsoon, causing a major loss of life and property. Therefore, it was necessary to look for a solution to increase growth and vigilance in order to lessen losses related to landslides caused by natural disasters. By utilizing contemporary technologies, an early warning system might be developed. Artificial neural networks (ANNs) are widely used nowadays across many industries. This paper's major goal is to provide new integrative models for assessing landslide susceptibility in a prone area of north of Pakistan. To do this, the training of an artificial neural network (ANN) is supervised using metaheuristic and Bayesian techniques: particle swarm optimization algorithm (PSO), Genetic algorithm (GA), Bayesian optimization Gaussian process (BO_GP), and Bayesian optimization Gaussian process (BO_TPE). 304 previous landslides and the eight most prevalent conditioning elements combine to form a geographical database. The models are hyper-parameter optimized, and the best ones are employed to generate the susceptibility maps. The area under the receiving operating characteristic curve (AUROC) accuracy index found demonstrated that the maps produced by both Bayesian and metaheuristic algorithms are highly accurate. The effectiveness and efficiency of applying artificial neural networks (ANNs) for landslide mapping, susceptibility analysis, and forecasting are studied in this research it’s observed from experimentation that the performance differences for GA, BO_GP, and PSO compared to BO_TPE are relatively small, ranging from 0.3166% to 1.8399%. This suggests that these techniques achieved comparable performance to BO_TPE in terms of AUC. However, it's important to note that the significance of these differences can vary depending on the specific context and requirements of the ML task. Additionally in this study, we explore eight feature selection algorithms to determine the geospatial variable importance for landslide susceptibility mapping along the KKH. The algorithms considered include Information Gain, Gain Ratio, OneR Classifier, Subset Evaluators, Principal Components, Relief Attribute Evaluator, Correlation, and Symmetrical Uncertainty. These algorithms enable us to evaluate the relevance and significance of different geospatial variables in predicting landslide susceptibility. By applying these feature selection algorithms, we aim to identify the most influential geospatial variables that contribute to landslide occurrences along the KKH. The algorithms encompass a diverse range of techniques, such as measuring entropy reduction, accounting for attribute bias, generating single rules, evaluating feature subsets, reducing dimensionality, and assessing correlation and information sharing. The findings of this study will provide valuable insights into the critical geospatial variables associated with landslide susceptibility along the KKH. These insights can aid in the development of effective landslide mitigation strategies, infrastructure planning, and targeted hazard management efforts. Additionally, the study contributes to the field of geospatial analysis by showcasing the applicability and effectiveness of various feature selection algorithms in the context of landslide susceptibility mapping.

Early-life adversity can profoundly impact individual development, yet some demonstrate resilience. Longitudinal studies tracking individuals over extended periods have aided our understanding of resilience and growth following adverse childhood experiences. This paper reviews insights from influential studies like the Kauai Longitudinal Study, the Adverse Childhood Experiences (ACE) Study, and the Dunedin Study. It explores key findings on risk and protective factors, adaptation trajectories, and long-term outcomes associated with resilience. Theoretical frameworks and methodological considerations are discussed. The paper examines how this research informs interventions, policies, and support systems for fostering resilience. It highlights the need for diverse samples, integrating biological and environmental factors, and investigating intergenerational impacts. By synthesizing longitudinal research, this paper elucidates complex pathways to resilience and positive development despite early adversity, offering insights for research and supporting vulnerable populations.

Longitudinal studies tracing high-risk samples over decades have illuminated powerful pathways of resilient adaptation among individuals who overcome adversities faced early in life. This research demonstrates resilience is a common phenomenon driven by dynamic interactions between individual traits and environmental resources that enable positive adjustment despite adversity exposure. For clinical social workers supporting clients impacted by childhood trauma, abuse, violence and other adversities, understanding these resilience processes is vital for developing strengths-based, trauma -informed interventions that enhance positive adaptation. This paper synthesizes key findings from landmark longitudinal resilience studies and explores specific practice implications for resilience-oriented clinical assessment, intervention planning, prevention efforts, and social worker training. By integrating resilience research insights, social workers can more effectively identify and cultivate clients' innate capacities for resilience, facilitating a journey towards posttraumatic growth.

The paper's main goal is to introduce a novel type of interpolative convex contraction and build up some fresh findings for it using the interpolative convex contractions' progressive approach. We have established certain conclusions using orbitally S-complete and Suzuki type contractions in F-metric spaces. My research aims to examine the fixed point method's efficacy in solving fractional differential equation with boundary conditions.

Findings of new targeted treatments with adequate safety evaluations is essential for better cancer cures and mortality rates. Immunotherapy holds promise for patients with relapsed disease, with the ability to elicit long-term remissions. Emerging promising clinical results in B-cell malignancy using gene-altered T-lymphocytes uttering chimeric antigen receptors have sparked a lot of interest. This treatment could open the path for a major difference in the way we treat tumors that are resistant or recurring. Genetically altered T cells used to produce tumor-specific chimeric antigen receptors are resurrected field of adoptive cell therapy by demonstrating remarkable success in the treatment of malignant tumors. Because of the molecular complexity of chimeric antigen receptors -T cells, a variety of engineering approaches to improve safety and effectiveness are necessary to realize larger therapeutic uses. In this study, we investigate at new strategies for enhancing chimeric antigen receptors-T cell therapy by altering chimeric antigen receptors proteins, T lymphocytes, and their relations with other solid tumor microenvironment (TME) aspects.

Khabib Nurmagomedov versus Conor McGregor Ultimate Fighting Championship (UFC) 229 battle was among the most controversial mixed martial art fights of the past decade. In this study, the author examined how the various popular media outlets from the Eastern and Western world portrayed Khabib Nurmagomedov after UFC 229. The author used Huntington’s (1993) clash of civilization thesis by grounding it in the Orientalism and Occidentalism paradigms to examine the phenomenon. Fairclough’s (1989, 1995) model for critical discourse analysis was employed to investigate the various Western and Eastern popular press and digital media platforms (i.e., newspapers, blogs, and sporting news websites). The author analyzed 57 (Western n = 38, Eastern n = 19) media reports per the inclusion criteria. The study results unveiled conflicting predispositions present in the Western and Eastern media for Khabib Nurmagomedov. This study contributes to the limited knowledge about how a Muslim man athlete with diverse racial and ethnic backgrounds is seen contrarily in the Western and Eastern media. The author discusses the theoretical implications of the study.

Forest road pavement needs an evaluation methodology based on a comprehensive assessment of road conditions. This research was conducted to evaluate the performance of a method for rating the surface condition of forest roads and eventually to adapt the method to the situation prevailing in a forest road network. The rating method selected as the basis for this experiment was the pavement condition index (PCI) developed by the U.S. Army Corps of Engineers. A 53 km of forest roads were selected contained the most influential factors and conditions variability. Eventually, 201 road segments were delineated between 150-300 m in length. Within the given segments, sample plots were set 20 m in length consecutively. It was concluded that the panel scores for distress and surface condition of sample unit and section differed from forest road pavement condition index (FRPCI) and PCI. Linear regression was used to derive equations between distress and PCI score to determine effective FRPCI parameters that provide a numerical rating for the condition of road segments within the road network, where 0 worlds are the worst possible condition, and 100 is the best possible condition best. Also, regression analysis showed the FRPCI model with a 0.87 correlation for the total of the road is a performance index used for the first time in forest roads. This study showed a range of FRPCI from 7.8 to 96.3, different from PCI and URCI ratings (0.85-45 and 1.2-53). The FRPCI index helps forest managers in road maintenance, harvesting, and planning to use road information.

Objectives: One of the home-made herbal remedy being traditionally used against gout is evaluated to identify any new and characteristic marker compound which may be used as characteristic analytical marker to standardize this polyherbal remedy. Materials and method: A distinct and remarkable peak in the HPLC chromatogram of remedy was identified which was further isolated by fraction collector. This fraction was then evaporated and characterized for structure elucidation using set of various techniques such as RP-HPLC,UV, FTIR, TLC, EIMS and NMR. Results: The compound characterized was non polar compound, ester of betulin and palmitoleic acid. Although the remedy has been standardized using set of four markers as discussed in literature but this newly developed marker compound can be used to further standardize this remedy and other herbal preparations comprising of this marker compound.Conclusion: Hence the isolated compound can be used as novel analytical marker in the standardization of this herbal remedy and the other herbal preparations containing such marker compound

Introduction: Child stunting remains a public health concern. It is characterized as poor cognitive and physical development in children due to inadequate nutrition during the first 1,000 days of life. Across South Asia, Pakistan has the second-highest prevalence of stunting. This study has assessed the most recent nationally representative data, the National Nutrition Survey (NNS) 2018, to identify the stunting prevalence and determinants among Pakistani children under five. Methods: The NNS 2018, a cross-sectional household-level survey, was used to conduct a secondary analysis. Data on malnutrition, dietary practices, and food insecurity was used to identify the prevalence of stunting among children under five years by demographic, socioeconomic, and geographic characteristics. The prevalence of stunting was calculated using the World Health Organization (WHO) height for age z-score references. Univariate and multivariable logistic regressions were conducted to identify factors associated with child stunting. Results: Analysis showed that out % of 52,602 children under five, 40.0% were found stunted. Male children living in rural areas were more susceptible to stunting. Furthermore, stunting was more prevalent among children whose mothers had no education, were between 20 and 34, and were employed. In the multivariable logistic regression, male children (AOR=1.08, 95% CI[1.04-1.14], P<0.001) from rural areas (AOR=1.07, 95% CI [1.01-1.14], P=0.014), with the presence of diarrhea in the last two weeks (AOR=1.15, 95% CI [1.06-1.25], P<0.001), with mothers who have no education (AOR=1.57, 95% CI [1.42-1.73], P<0.001) or lower levels of education (Primary: AOR=1.35, 95% CI [1.21-1.51], P<0.001; Middle: AOR=1.29, 95% CI [1.15-1.45], P<0.001) had higher odds of stunting. Younger children aged <6 months (AOR=0.53, 95% CI [0.48-0.58], P<0.001) and 6-23 months (AOR=0.89, 95% CI [0.84-0.94], P<0.001), with mothers aged 35-49 years (AOR=0.78, 95% CI [0.66-0.92], P=0.003) had lower odds of stunting. At the household level, the odds of child stunting were higher in the poorest households (AOR=1.64, 95% CI [1.46-1.83], P<0.001), with ≥7 members (AOR=1.09, 95% CI [1.04-1.15], P<0.001), with no access to improved sanitation facilities (AOR=1.14, 95% CI [1.06-1.22], P<0.001) and experiencing severe food insecurity (AOR=1.07, 95% CI [1.01-1.14], P=0.02). Conclusion: Child stunting in Pakistan is strongly associated with various factors, including gender, age, diarrhea, residence, maternal age and education, household size, food and wealth status, and access to sanitation. To address this, interventions must be introduced to make locally available food and nutritious supplements more affordable, improve access to safe water and sanitation, and promote female education for long-term reduction in stunting rates.

Purpose, This research aimed to examine the effect of green logistics (GL) and green human resource management (GHRM) on the performance of environmentally friendly manufacturing industries oriented towards sustainable development of organizations (SDO) through the role of sustainable production (SP) as a mediating variable. Methodology, A quantitative approach was employed through a standardized questionnaire to obtain data from 110 manufacturing industries in Indonesia that implemented environmentally friendly practices. Advanced statistical techniques, such as Structural Equation Modeling (SEM) and data analysis using Smart PLS (Partial Least Square) version 4 were utilized to analyze the collected data. Findings, The results showed that the model supported the statistical significance of all seven hypotheses and confirmed the direct and mediating effects of GL, GHRM, and SP on SDO. Practical implications, This research added critical insights into the theory and practice of GL and GHRM to realize SDO through the role of SP as a mediator in environmentally friendly manufacturing industries. Originality, This research contributd to the existing literature by adding to the effect of SP mediation on the relationship of GL and GHRM on SDO. There was no previous research that discussed the important role of SP mediation in influencing the relationship between GL and GHRM on SDO.

Soft tactile sensors based on piezoresistive materials have various large-area sensing applications. However, their accuracy is often affected by hysteresis, a phenomenon that poses a significant challenge during operation. This paper introduces a novel approach that employs a backpropagation (BP) neural network to address the hysteresis nonlinearity in conductive fibre-based tactile sensors. To assess the effectiveness of the proposed method, four sensor units with different layer configurations (1, 3, 6, and 12) were designed. These sensor units underwent force sequences to collect corresponding output resistances. A backpropagation network was trained using these force sequences, thereby correcting the resistance values. The training process exhibited excellent convergence, effectively adjusting the network's parameters to minimize the error between predicted and actual resistance values. As a result, the trained BP network accurately predicted the output resistances. Several validation experiments were conducted to highlight the primary contribution of this research. The proposed method reduced the maximum hysteresis error from 24.2% of the sensor's full-scale output to 13.5%. This improvement establishes the approach as a promising solution for enhancing the accuracy of soft tactile sensors based on piezoresistive materials. By effectively mitigating hysteresis nonlinearity, the capabilities of soft tactile sensors in various applications can be enhanced. These sensors become more reliable and more efficient tools for force measurement and control, particularly in the fields of soft robotics and wearable technology. Consequently, their widespread applications extend to robotics, medical devices, consumer electronics, and gaming. Notably, the complete elimination of hysteresis in tactile sensors may not be feasible. Nevertheless, the proposed method effectively modifies the hysteresis nonlinearity, leading to improved sensor output accuracy.

Various heterogeneous devices or objects shall be integrated for transplant and seamless communication under the umbrella of internet of things (IoT). It would facilitate the open accession of data for the growth of a glut of digital services. To build a general framework of IoT is very complex task because of heterogeneity in devices, technologies, platforms and services, operating in the same system. In this paper, we mainly focus on the framework for big data analytics in smart city applications , which being a broad category specifies the different domains for each application. IoT is intended to support the vision of Smart City, where advance technologies will be used for communication for the quality life of citizens. A novel approach used in this paper, is for enhancing the energy conservation and to reduce the delay in big data gathering at tiny sensor nodes used in IoT framework. To implement the smart city scenario in terms of big data in IoT, an efficient (optimized in quality of service) WSN is required where communication of nodes is energy effcient. That is why, a new protocol QoS-IoT is proposed on the top layer of the architecture which is validated over the traditional protocols.

Background and Objective: Segmentation of the femur in Dual Energy X-ray (DXA) images poses challenges due to reduced contrast, noise, bone shape variations, and inconsistent X-ray beam penetration. In this study, we investigate the relationship between noise and certain deep learning (DL) techniques for semantic segmentation of the femur to enhance segmentation and bone mineral density (BMD) accuracy by incorporating noise reduction methods into DL models. Methods: Convolutional neural network (CNN) based models were employed to segment femurs in DXA images and evaluate the effects of noise reduction filters on segmentation accuracy and its effect on BMD calculation. Various noise reduction techniques were integrated into DL-based models to enhance image quality before training. We assessed the performance of the fully convolutional neural network (FCNN) in comparison to noise reduction algorithms and manual segmentation methods. Results: Our study demonstrated that FCNN outperformed noise reduction algorithms in enhancing segmentation accuracy and enabling precise calculation of BMD. The FCNN-based segmentation approach achieved a segmentation accuracy of 98.84% and a correlation coefficient of 0.9928 for BMD measurements, indicating its effectiveness in the clinical diagnosis of osteoporosis. Conclusions: In conclusion, integrating noise reduction techniques into DL-based models significantly improves femur segmentation accuracy in DXA images. The FCNN model, in particular, shows promising results in enhancing BMD calculation and clinical diagnosis of osteoporosis. These findings highlight the potential of DL techniques in addressing segmentation challenges and improving diagnostic accuracy in medical imaging.

For a considerable length of time synthetic composts are utilized to satisfy the dirt necessity of supplements and yield, however huge measure of these substance manures are hazardous for condition, advantageous microorganisms, creatures, and people also. In this way, natural inviting and savvy biofertilizers are utilized. Biofertilizer are the substances which contain microorganisms those microorganisms might be growths, microscopic organisms, and protozoa which have capacity to build ripeness of soil by Nitrogen obsession, Phosphorous solubilization, and Iron sequestration. These cycles convert insoluble type of supplements into solvent structure and make it accessible to the foundations of plant which effectively take them up and use them. There are assortment of the yields whose profitability can be expanded by applying biofertilizer, for example, rice, oat, and other grain crops. In this audit we experience the method of utilization of biofertilizers, and how the assistance the plants and in which they help.

Biological polymers such as tissue-engineered scaffolds and skin grafts with improved properties are very required in the pharmaceutical field. The wound-dressing gelatin/chitosan/moringa leaf extract (G-CH-M biopolymer) was synthesised and characterised. The blood compatibility, anti-inflammatory, antioxidant, and antibacterial activities of the biopolymer were investigated. Our results showed that S. aureus swarming motility was drastically affected. However, the biopolymer had no significant effect on the swarming motility of E. coli compared to the control. In addition, biopolymers showed high antibacterial capacities, especially against S. aureus. The biopolymer was also found to be effective in protecting plasmid DNA against oxidative stress. Furthermore, the biopolymer exhibits greatly suppressed hemolysis (lower than 2%), even at a high concentration of 50 mg/mL. These results indicated that this novel biopolymer formulation could be further developed for wound care and contamination prevention.

Identifying ambient noise-based (ANb) signatures of streams can help in the estimation of their erosive potential (EP) that promotes reverie landslides and soil losses in the fluvial valleys. This is particularly imperative on flooding or rainy days, leading to stronger erosion-prone conditions (colluvium and boulders) of the valley beds inferred from georadar attribute analysis. Developing such research direction can benefit the local communities, as is the case with the Cerrado region of Brazil, where these phenomena have high destructive potential with social, economic, and climatic implications. For the present study, a seasonal stream in the Federal District of Brazil was investigated by ANb monitoring supported by Ground Penetration Radar (GPR) for site characterization. The ANb monitoring was conducted (at a safe distance) with a seismometer over several durations of dry and rainy conditions. The power spectral density (PSDs) was computed as a function of several variables, including weather conditions (rainfall, wind speed, and pressure), time-frequency spectrograms, and ambient noise displacement root mean square (RMS). This analysis also considered the single station horizontal-to-vertical spectral ratio (HVSR), where rain, wind, pressure, river flow and anthropogenic signatures were evident (at selective frequency ranges). Multi-peaks that emerged on the HVSR curve were further analyzed to identify amplitude and frequency changes, and the three peaks shift on average to a lower position during the rainy period. The GPR amplitude and waveform variation features were attributed to the stratigraphy (i.e., the boundary between valid and invalid regions and coherence value) of the floodplain and regions susceptible to erosion (erosion-prone lithological spots). This approach provides the basis for non-destructive monitoring tools enabling the detection of 'seismic signatures' and weak spots of the fluvial channels for improving environmental management.

Despite the increasing role of machine learning in various fields, very few works considered artificial intelligence for frequency estimation (FE). This work presents a comprehensive analysis of deep-learning (DL) approach for frequency estimation of single-tones. It is shown that DL network with two layers having a few nodes can estimate frequency more accurately than well-known classical techniques. The study is comprehensive, filling gaps of existing works, where it analyzes error under different signal-to-noise ratios, numbers of nodes, and numbers of input samples; also, under missing SNR information. It is found that DL-based FE is not significantly affected by SNR bias or number of nodes. DL-based approach can work properly using minimal number of input nodes N at which classical methods fail. It is possible for DL to use as little as two layers with two or three nodes each, with complexity of O{N} versus O{Nlog2 (N)} for DFT-based FE, noting that less N is required for DL. Hence, DL can significantly reduce FE complexity, memory, cost, and power consumption, making DL-based FE attractive for resource-limited systems like some IoT sensor applications. Also, reduced complexity opens the door for hardware-efficient implementation using short word-length (SWL) or time-efficient software-defined radio (SDR) communications.

With the advent of digitization, the integration of advanced technologies in operations and projects across all sectors is in progress. Accordingly, efforts are being made to utilize cutting-edge technologies to improve the circularity of the built environment. This study aimed to review the existing applications and limitations of building information modeling (BIM) tools for circular economy (CE) implementation from this perspective. A literature review was conducted to provide an overview of the use of BIM tools for conducting life cycle assessments, energy analysis, waste management, and formulation of material passports for buildings. It was found that BIM tools, which are available across all life cycle phases of building, have a great potential to improve the circularity of the sector. The overview provided on the use of various BIM tools may help stakeholders of the built environment understand the role of BIM for CE adoption in the sector.

High antioxidants level in food is gradually becoming popular because of the enhanced risk of oxidative stress in humans. Bread wheat is rich in vital antioxidants but its major bioactive compounds are not available for the human. This study was conducted with the aim to enhance the phytochemical constituents and antioxidative activity of wheat grains by fermenting it with the use of Bacillus subtilis KCTC 13241. The antioxidative potential was determined by DPPH (2,2-diphenyl-1-picryl- hydrazyl) and ABTS (3-ethyl-benzothiazo- line-6-sulfonic acid) radical scavenging assay as well by the concentration of amino acids, flavonoids, minerals, carbohydrates, and phenolic compounds. Different varieties showed different free radical scavenging potential on fermentation, which was significantly high with respect to their corresponding unfermented wheat varieties. The highest potential was found in a fermented wheat variety named Namhae and this combination can be used in the pharmaceutical and food industries.

As an on-going pandemic caused by the out-break of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) or simply COVID-19 sweeps through the globe at an unprecedented rate leaving behind trails of high infection and mortality, it is crucial to understand the propagation dynamics of the virus in a host population in order to take urgent and effective remedial and mitigating steps to save life. It is already observed in many countries and communities that accurate and timely testing, tracing, and tracking of the infection lead to better containment and slowing down of the spread. In this exploratory research, the early growth dynamics of infection within a population is pursued based on real data. The study posits that the early growth in a homogenous population follows an exponential pattern motivating further rigorous quantitative treatment based on a number of analytical models such as logistic model, Richard’s model, and Gompertz model– the acceleration pattern of the outbreak is ascertained from the daily inflection data, and regression analysis against population models yields dynamic growth indices which allow very accurate prediction of the successive outbreak size when calibrated continually with updated data. The performance of the various models is evaluated with the real dataset. More, the basic reproduction number of the COVID-19 virus propagation in the community is estimated based on the on-set phase dataset using multi-compartmental epidemiological model. Also, the maximum infection size, infection doubling time and the scope of the herd immunity are also inferred for COVID-19 in a population.