Thyroid surgery has been for years one of the most common elective procedures performed in general surgery. In the last 25 years, there have been significant advances in the diagnosis and treatment of thyroid disorders, and new technologies are being implemented. The aim of this study was to ana-lyze 25 years of experience in thyroid surgery in the Department of General, Minimally Invasive and Endocrine Surgery at the Medical University of Wroclaw in terms of demographic changes, indica-tions for surgical treatment, the type of thyroid surgery performed and complications. The impact of recent advances on changes in endocrine surgery was evaluated. For this purpose, clinical material from the years 1996-2020 was analyzed, with a total of 3748 patients (7285 RLN at risk of injury). Period I included the years: 1996-2003, period II: 2011-2015 and 2018-2020. Results: In the last 25 years, the percentage of patients operated on for thyroid cancer has increased threefold (p <0.00001); the extent of thyroid surgery has changed: in 1996-2003, subtotal thyroid operation was performed in more than 90% of patients vs. 1.7% of total thyroid gland surgery; 2011-2015 and 2018-2020 were more than 94% of total thyroid surgery vs. 4% of subtotal surgery (p<0.00001). The increase in the extent of surgery did not affect the percentage of total amount recurrent laryngeal nerve palsy (RLN palsy) (5.17% vs. 4.38% p = 0.1785), it did affect the percentage of transient RLN palsy in group II vs. group I (0.41% vs. 1.34%, p<0.00001), while the percentage of permanent RLN palsy in group I was statistically significantly higher than in group II (4.77% vs. 3.05%, p=0.0016). An increase in the percentage of postoperative clinical hypoparathyroidism in group II was observed: 4.84% vs. 8.93% (p<0.00001). Conclusions: Over 25 years, there has been a significant increase in the number of sur-geries performed for thyroid cancer, the range of surgeries from partial resections to total excision of the thyroid gland has changed, and the increased range of surgeries did not have a statistically signifi-cant effect on the number of vocal fold paralysis, but increased the percentage of postoperative hypo-parathyroidism. Intraoperative neuromonitoring had a significant impact on changing the scope of surgery and preventing complications.

Background: Old age and illnesses can limit physical activity (PA). Objectives: To assess the level of PA and its limitations. Design: Cross-sectional study, January and June 2024. Setting: Diabetes Center. Subjects: Patients (N=207) >64 years with diabetes (DM). Methods: Surveying using: IPAQ, Accompanying Survey (AS). The significance was assessed by: Student’s t-test, Mann-Whitney U test, Pearson’s test. The relationships between the IPAQ and the AS results were analyzed based on a meta-analysis model for variable effects, OR with a 95% CI. ROC curve was used to determine the threshold values for age, BMI. Correlations between selected key variables were evaluated using the PCA. Results: The median age: 72 years (65–87), BMI: 28.70 kg/m2 (18.61–49.69). The median PA level: 1,837 MET-min/week (0–9,891). The individuals who obtained insufficient (n=28), sufficient (n=75), and high levels of PA (n=53) were 17.95%, 48.08%, and 33.97%, respectively. Diseases were the main factor limiting PA (53,54%) in patient’s opinion, followed by the lack of a companion or motivation. The meta-analysis found no diseases linked to insufficient PA, but those with BMI > 33.3 kg/m² and over 75 years old more often had insufficient PA. PCA revealed several characteristics that predispose individuals to insufficient PA. Conclusions: People over 75 years of age tend to avoid PA more than younger seniors, leading to its insufficient level, similarly like higher BMI. The individual with DM who has an insufficient level of PA is typically a single, woman, over 75, BMI>33.

The correlation between pain and emotional status in subjects with temporomandibular disorders (TMD) is known. Regardless of that up to date these findings were seldomly confronted with the objective assessment of pain using a digital algometer on the mastication muscles. The aim of the study was to investigate the relationship between the emotional status, chronic pain pain pressure threshold (PPT). 38 subjects were screened for the existence of temporomandibular disorders with the 3Q/TMD questionnaire, for chronic pain (GCPS) and emotional status (PHQ-9 and GAD-7). The results were confronted with the PPT measured with the digital algometer on the masseter muscles. Each subject was examined three times (after 1 month and after 7 months from the initial exami-nation session. Chronic pain scores (GCPS) were found to be higher in the TMD group in all three examination sessions (p<0,05). The pain, depression and anxiety levels were higher in females de-spite the existence of TMD, but only some were significant.A correlation between chronic orofacial pain scores and PPT was found in 2 out of 3 examination sessions. The PPT scores on the masseter muscles did not correlate with the emotional state in the study population.

Titania is one of the most comprehensively studied nanostructures due to its widespread applications in production of catalytic, gas- sensing and corrosion- resistance materials [1]. M-polynomial of nanotubes has been vastly investigated as it produces many degree-based topological indices which are numerical parameters capturing structural and chemical properties. These indices are used in the development of quantitative structure-activity relationships (QSARs) in which the biological activity and other properties of molecules are correlated with their structure like boiling point, stability, strain energy etc of chemical compounds. In this paper, we determine M-polynomials of single-walled titanium (SW TiO2) nanotubes and recover important topological degree based indices of them to theoretically judge these nanotubes. We also use Maple to plot surfaces associated to different types of single-walled titanium (SW TiO2) nanotubes.

Various autoimmune diseases, including autoimmune hypothyroidism (AHT), are associated with a higher risk of developing mood disorders throughout life. Depression is accompanied by the changes in the levels of inflammatory and trophic factors, including interleukines (IL-1beta, IL-2, IL-6), interferon alpha (IFN-alpha), tumor necrosis factor alpha (TNF-alpha), C-reactive protein (CRP) and brain derived neurotrophic factor (BDNF). Similar disturbances in the cytokine profile are seen in AHT patients and their relatives. Disclosure of the relationship between the co-existence of depression and autoimmune subclinical thyroiditis indicates that the pathomecha-nism of depression may be related to the changes in the immune system, it is possible that both conditions may be caused by the same immune processes. The above hypothesis is indirectly sup-ported by the observations that the treatment with both antidepressants and levothyroxine leads to a decrease in the levels of proinflammatory cytokines with an increase in BDNF concentrations, simultaneously correlating with an improvement in the clinical parameters. However, so far there are no long-term studies determining the causal relationship between depression, thyroid auto-antibodies, and cytokine profile, which could bring us closer to understanding the interrelation-ships between them and facilitate the use of an adequate pharmacotherapy, not necessarily psy-chiatric. We consider the above issues insufficiently investigated but of great importance. This ar-ticle is an overview of the available literature as well as an introduction to our research project.

This paper deals with bistatic subsurface probing of a horizontally layered dielectric half-space by means of ultra-wideband electromagnetic pulses. A receiver collects reflections from the air-ground interface and from the gradients of dielectric permittivity in the half-space. This scenario is of interest for ground penetrating radar (GPR) applications. For the analytical description of the received signal, we developed and implemented a novel time-domain version of the coupled-wave Wentzel–Kramers–Brillouin approximation. Our solution is in very good agreement with finite-difference time-domain results, radically accelerates calculations, and effectively accounts for the protracted return signals observed in the lower part of the GPR spectrum. The paper includes results showing the application of the proposed technique to two case studies: in particular, the method was employed for the post-processing of experimental radargrams collected on Lake Chebarkul, in Russia, and to simulate GPR probing of the Moon surface, to detect smooth gradients of the dielectric permittivity in lunar regolith.

This paper presents a methodology for indirectly estimating the scale of seabird bycatch using existing data, eliminating the need for regular monitoring. The study focuses on five species of ducks that winter in the Polish waters of the Baltic Sea and are highly susceptible to bycatch: Long-tailed Duck, Velvet Scoter, Common Scoter, Greater Scaup, and Tufted Duck. The evaluation units used are divided into the Bornholm and Gotland Groups within the Polish Exclusive Economic Zone (PEEZ). The analysis acknowledges the lack of data for certain areas known to have high concentrations of diving birds and fishing activity. The population sizes of waterbirds were assessed using ship-based surveys and a distance sampling approach. Fishing effort data from the winter seasons between 2015/2016 and 2019/2020 were analyzed. Bycatch rates were estimated based on surveys conducted in previous seasons, and threshold values for bycatch were established using the concept of "small numbers" defined in EU directives. The results show that within the Gotland subdivision of the PEEZ, the estimated average abundance of all diving waterbirds was 207,114 individuals, with an average bycatch of 7,921 birds (3.8% of the total). The Velvet Scoter was the most abundant species, followed by the Long-tailed Duck. Benthivorous ducks constituted the majority of the bird population in the area. In the Bornholm subdivision, the estimated average abundance of diving waterbirds was 600,845 individuals, with an average bycatch of 5,056 birds (0.8% of the total). The Long-tailed Duck was the most numerous species, followed by the Velvet Scoter. Benthivorous ducks also dominated in this area. The findings highlight the need for effective management and conservation measures to address the high mortality of seabirds due to bycatch. The methodology presented in this study offers a valuable approach for estimating bycatch scale and can support efforts to minimize the impact on seabird populations in the Baltic Sea.

Abstract: As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: b-O-4 linkage, B: phenylcoumaran, C: resinol, D: b-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70 % and significantly lower in stem and mixture lignins at around 60 % and almost 65 %. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20 % or more (maximum is M. sinensis Sin2 with over 30 %). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27 %. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.

The preparation of transition metal salt ammine complexes having oxidizing anions is a great challenge due to the reaction between the ammonia and oxidizing anions during the synthesis of these materials. However, they have an important role in the development of new oxidants in organic chemistry and especially as precursors in the preparation of mixed metal oxides and alloys in controlled temperature thermal decomposition reactions. Therefore, the synthetic procedures to prepare the complexes of transition metal permanganate, pertechnetate, and perrhenate (VIIB group tetraoxometallates) salts with ammonia as ligand or co-ligand have been comprehensively reviewed. The available data about the structure and spectroscopic properties of these compounds, including the hydrogen bonds that act as redox reaction centers under their thermal decomposition are given and evaluated. Their thermal decomposition processes and products have been summarized. The available pieces of information about their role in organic oxidation reactions like the oxidation of benzyl alcohols, and regeneration of oxo-compounds from oximes and phenylhydrazones including the kinetics of these processes have also been collected.

Lymphangioleiomyomatosis (LAM) is characterized by lung cysts that cause lung deterioration, changes in the lymphatic system, and tumors in the kidneys. It mainly affects women of reproductive age and is a progressive disease. LAM can occur as an isolated disease or coexist with tuberous sclerosis (TSC). The source of LAM cells is unknown. Patients with confirmed LAM should be treated with an mTOR inhibitor, sirolimus, or everolimus. We present a case of LAM with TSC in a patient whose symptoms, including lymph nodes and chyaloperitoneum, mainly concern the abdominal cavity.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

Background/Objectives: Meconopsis has long been used in traditional Tibetan medicine to treat various diseases. However, blue-flowered Meconopsis (M. betonicifolia) is becoming increasingly scarce due to overharvesting. As a potential alternative, yellow-flowered Meconopsis (M. integrifolia) shows promise but requires comprehensive characterization. This study aimed to evaluate and compare the anti-inflammatory potential of yellow- and blue-flowered Meconopsis species. Methods: LC-MS was used to analyze the chemical profiles of yellow- and blue-flowered Meconopsis. Putative targets of shared constituents were subjected to GO and disease enrichment analysis. The LPS-induced RAW264.7 macrophage model was employed to assess anti-inflammatory effects. Metabolomics was applied to gain mechanistic insights. Results: LC-MS revealed over 70% chemical similarity between species. Enrichment analysis associated targets with inflammation-related pathways. In macrophage assays, both species demonstrated dose-dependent anti-oxidative and anti-inflammatory activities, with yellow Meconopsis exhibiting superior efficacy. Metabolomics showed modulation of key inflammatory metabolic pathways. Conclusions: This integrative study validated yellow-flowered Meconopsis as a credible alternative to its blue-flowered counterpart for anti-inflammatory applications. Metabolic profiling provided initial clues regarding their multi-targeted modes of action, highlighting clinical relevance and potential for sustainable utilization and biodiversity conservation.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

From a differential geometric perspective, information geometry (IG) aims to characterise the structure of statistical geodesic models. The research done for this paper offers a novel method for modelling the information geometry of a queuing system. From the perspective of IG, the manifold of the transient M/M/infinity queue is described in this context. The Fisher Information matrix (FIM) as well as the inverse of (FIM), (IFIM) of transient M/M/infinity QM are devised. In addition to that, new results that uncovered the significant impact of stability of QM on the existence of (IFIM) are obtained. Moreover, the Geodesic equations of motion of the coordinates of the underlying transient are obtained. Also, it is revealed that stable QM is developable (i.e., has a zero Gaussian curvature) and has a non-zero Ricci Curvature Tensor (RCT). Novel stability dynamics of transient M/M/iInfinity queue manifold is revealed by discovering the mutual dual impact between the behaviour of (RCT) and the stability(instability) phases of M/M/Infinity QM. Furthermore, a new discovery that presents the significant impact of stability of queue manifold and the continuity of the unique representation between M/G/1 queue manifold and Ricci Curvature Tensor (RCT). The information matrix exponential (IME) is devised. Also, it is shown that stability of the devised (IME) enforces the instability of M/M/ Infinity QM. More interestingly, novel relativistic info-geometric queueing theoretic links are revealed .

Kynurenic acid (KYNA), a tryptophan metabolite, is believed to exert neuromodulatory and neuroprotective effects in the brain. The study aimed to examine the KYNA’s capacity to modify gene expression and the activity of cellular antioxidant enzymes in specific structures of the sheep brain. Anestrous sheep were infused intracerebroventricularly with two KYNA doses: lower (4×5 μg/60 μL/30 min, KYNA20) and higher (4×25 μg/60 μL/30 min, KYNA100) at 30min intervals. The abundance of superoxide dismutase (SOD2), catalase (CAT) and glutathione peroxidase (GPx1) mRNA, as well as enzyme activities (µM/µg of protein), were determined in the hypothalamic medial-basal (MBH) and preoptic (POA) areas, and in the hippocampal CA1 field. Both doses of KYNA caused a decrease (P&lt;0.01) in the expression of SOD2 and CAT mRNA in all structures examined compared to the control group (except for CAT in the POA at the KYNA100 dose). Furthermore, lower levels of SOD2 mRNA (P&lt;0.05) and CAT mRNA (P&lt;0.01) were found in the MBH and POA and in the POA and CA, respectively, in sheep administered with the KYNA20 dose. Different stimulatory effects on GPx1 mRNA expression were observed for both doses (P&lt;0.05-P&lt;0.01). KYNA exerted stimulatory, but dose-dependent effects on SOD2, CAT and GPx1 activities (P&lt;0.05-P&lt;0.01) in all brain tissues examined. The results indicate that KYNA may influence the level of oxidative stress in individual brain structures in sheep by modulating the expression of genes and activity of at least SOD2, CAT and GPx1. The present findings also expand the general knowledge about the potential neuroprotective properties of KYNA in the central nervous system.

Complicated grief (CG) predicts decreased mental health over time. Furthermore, feeling connected to nature (CN) is positively associated with beneficial mental health outcomes, such as psychological wellbeing and perceived psychological resilience. Thus, we hypothesized that CN moderates the association between general grief or CG and negative mental health for bereaved people. Further, we hypothesized that one’s physical exposure to nature—that is, estimated time spent in nature and greenness (i.e., vegetation) surrounding one’s residential area—might moderate the association between general grief or CG and negative mental health for bereaved people. To test these hypotheses, we sampled 153 participants who experienced the death of a close other by COVID-19 infection. Participants reported CG, general grief, anxiety symptoms, depression symptoms, CN, estimated time spent in nature, and residential area postal code via a single online survey. We estimated greenness surrounding participants’ residential areas using their self-reported 5-digit U.S. postal code. Cross-sectional analyses indicated that, as predicted, CN attenuated the association between CG and depression, but only trended toward moderating the association between CG and anxiety and did not moderate the associations between general grief and depression or anxiety. Other variables related to the experience of nature—the estimated time an individual spends in nature and the greenness surrounding one’s residential area—did not moderate the association between general grief or CG and depression or anxiety. We thus conclude that a sense of feeling connected to nature—not simply spending more time in nature or being surrounded by nature—may serve an important role in the mental health status of people experiencing complicated grief, perhaps because CN replenishes general belonging when someone significant has passed away.

Retention mechanisms in HILIC have been investigated and reported in literature. However, the current understanding of the retention mechanisms is qualitative and lacks quantitative details. Previously, mechanism elucidation was based on indirect evidence, and unambiguous assignment of retention mechanisms has not been reported based on direct data. This study aims to quantitatively determine the contributions of two major retention mechanisms in HILIC, hydrophilic partitioning and surface adsorption to the overall retention of neutral compounds. Using the methodologies we developed previously, the phase ratio for adsorbed water layer and distribution coefficients were measured and used to calculate the retention factors attributed to hydrophilic partitioning. The methodology allows the determination of the contribution of surface adsorption simultaneously. The evaluation of five test compounds demonstrates that the retention may be controlled by hydrophilic partitioning, surface adsorption or both depending on compound characteristics. Quantitative assessment of retention mechanisms also makes it possible to better understand the effect of acetonitrile on retention in HILIC.

A new set of basis functions is presented. The foundation in mathematics is established. To reconstruct a signal, it is compared to the Fourier basis functions. The M-basis functions' potential applications are also presented.

Depression and metabolic diseases often coexist having several features in common, e.g., chronic low-grade inflammation and intestinal dysbiosis. Different microbiota interventions have been proposed to be used as a treatment for these disorders. In the paper we review the efficacy of probiotics in depressive disorders, obesity, metabolic syndrome and its liver equivalent based on the published experimental studies, clinical trials and meta-analyses. Probiotics seem to be effective in reducing depressive symptoms when administered in addition to antidepressants. Additionally, probiotics intake may ameliorate some of the clinical components of metabolic diseases. However, standardized methodology regarding probiotics clinical trials has not been established yet. In this narrative review we discuss current knowledge on the recently used methodology with its strengths and limitations and propose criteria that may be implemented to create a new study of the effectiveness of probiotics in depressive disorders comorbid with metabolic abnormalities. We put across our choice on type of study population, probiotics genus, strains, dosages and formulations, intervention period, as well as primary and secondary outcome measures.

Metabolic disorders, metabolic syndrome and non-alcoholic fatty liver disease, and depression are those of the most common and debilitating disorders worldwide that often coexist further increasing mortality risks. Although the exact mechanisms underlying this association are poorly known, several hypotheses have been proposed: antipsychotic medication and antidepressants use, diet and physical activity or any other lifestyle factors. However, the high co-occurrence rate of depression and metabolic disorders suggests a possible pathophysiological overlap. In this paper I review several raised mechanisms for this overlap which are the hypothalamic-pituitary-adrenal axis dysregulation, immune alterations with chronic inflammation, as well as oxidative stress. In my view, there is one common thread running through all the aforementioned areas of pathophysiology which is microbiota alteration. So far, several possible interventions in our microbiota have been introduced into clinical practice - dietary and other lifestyle changes, supplementation with prebiotics or probiotics, fecal microbiota transplantation – but with vague indications. A better characterization of the above associations may represent a critical step at phenotyping, and a more targeted approach to the treatment of both depressive and metabolic disorders. At the end of the paper, I give several practical applications for future studies.

This paper presents geometric analyses of welded frames after free relaxing and vibratory stress relief (VSR). Respected frames were tested components of a prototype packaging machine. Two types of relaxation were carried out to remove stresses introduced as a result of welding process. One of the frame was subjected to free relaxing, while the other one to accelerated vibration relaxing. Detection of the frame geometry changes was performed using a photogrammetric system. In addition, an evaluation of the geometry change was conducted for fifteen variants of steel frame support. A comparative analysis of the geometric deviations of the frames after free and vibratory stress relief confirmed the assumption that the frame after vibration stress relief better reproduces the nominal dimensions. Nevertheless, it should be emphasized that after vibratory stress relief the frame is not subject to further deformation, which is a desirable effect. In the case of free relaxing, the frame undergoes dimensional changes in a random manner. In summary, carrying out accelerated vibratory stress relief allows control of spontaneous dimensional changes in the designed frame of a packaging machine resulting from spontaneous relaxation of stresses arising from the welding process. The shortening of the relaxation process of the welded frame is also an unquestionable advantage.

Nowadays, rotor-stator mixers are widely used in the chemical process industry to carry out the dispersion and de-agglomeration processes for manufacturing the homogenous electrode slurries. Development of the process simulation models for the turbulent mixing of these slurries helps to optimize the mixing parameters such as rotational speed and dispersion time. In this work, computational fluid dynamics (CFD) approach through ANSYS Fluent are explored to determine and analyze the flow patterns, velocity fields and viscosity distribution during the dispersion of anode slurries. It utilizes a non-homogeneous Eulerian multiphase approach and the typical k-ε model to create turbulence fields and compute the mixing rate. This work significantly improves our understanding of the relationship between rotor speed, dispersion time, viscosity distribution, and mixer geometry in rotor-stator mixers.

The current work reveals the fine tuning between stability zones and randomness of GI/M/1 Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary D/M/1 queueing system. More specifically, this clearly provides more insights into developing a contemporary PSFFA theory that unifies non-stationary queueing theory with chaos theory and fields in both theoretical physics and chaotic systems. This opens new grounds for stability analysis of non-stationary queueing systems. A notable application of GI/M/1 queueing model to achieve ultra-low latency of autonomous driving service is highlighted. Concluding remarks associated with future avenues of research are given.

We report on the occurrence of natural Magnesium Alumina Silicate Hydrate (M-(A)-S-H) cement at Feragen and Leka in eastern and western Trøndelag Norway, respectively. Both occurrences are located in the sub-arctic climate zone and form in glacial till and moraine material deposited on ultramafic rock during the Weichselian glaciation. Weathering of serpentinized peridotite dissolve brucite and result in a relative high pH alkaline fluid that subsequently reacts with the felsic minerals of the till (quartz, plagioclase, K-feldspar) to form a cement consisting of an amorphous material or a mixture of nanocrystalline Mg-rich phyllosilicates, including illite. The presence of plagioclase in the till results in the enrichment of alumina in the cement, i.e., forms M-A-S-H instead of the M-S-H cement. Dissolution of quartz results in numerous etch-pits and negative quartz crystals filled with M-A-S-H cement. Where the quartz dissolution is faster that the cement precipitation, a honeycomb-like texture is formed. Compositionally the cemented till (tillite) contains more MgO and has a higher loss of ignition than the till, suggesting that the cement is formed by a MgO fluid that previously reacted with the peridotite. The M-(A)-S-H cemented till represent a new type of duricrust, coined magsilcrete. The study of natural Mg-cement provides information on peridotites as a Mg-source for Mg-cement and as a feedstock for CO2 sequestration.

The misuse of antibiotics during the last decades led to the emergence of multidrug resistant pathogenic bacteria. This phenomenon constitutes a major public health issue. Consequently, the discovery of new antibacterials in the short term is crucial. Colicins, due to their antibacterial properties, thus constitute good candidates. These toxin proteins, produced by E. coli to kill enteric relative competitors, exhibit cytotoxicity through ionophoric activity or essential macromolecule degradation. Among the 25-colicin types known to date, colicin M (ColM) is the only one colicin interfering with peptidoglycan biosynthesis. Accordingly, ColM develops its lethal activity in E. coli periplasm by hydrolyzing the last peptidoglycan precursor, lipid II, into two dead-end products, thereby leading to cell lysis. Since the discovery of its unusual mode of action, several ColM orthologs have also been identified based on sequence alignments; all of the characterized ColM-like proteins display the same enzymatic activity of lipid II degradation and narrow antibacterial spectra. This publication aims at being an exhaustive review about what is currently known on this new family of antibacterial enzymes as well as on their potential use of food preservatives or therapeutic agents.

Materials characterised by magnetorheological properties are non-classic engineering materials. A significant increase in the interest of scientific community in materials from this group can be observed over the recent several years. The results of research presented in this article are oriented on the examination of said materials’ mechanical properties. In order to do so, stress relaxation tests were conducted on cylindrical samples of magnetorheological elastomers loaded with compressive stress for various values of magnetic induction (B1 = 0 mT, B2 = 32 mT, B3 = 48 mT, and B4 = 64 mT) and temperature (T1 = 25° C, T2 = 30° C, and T3 = 40° C). The results of these tests indicate that the stiffness of examined samples increases along with the increase of magnetic field induction and decreases along with the increase of temperature. On this basis, it has been determined that: the biggest stress amplitude change caused by the influence of magnetic field was σ0ΔB = 12.7% and the biggest stress amplitude change caused by the influence of temperature was σ0ΔT = 11.3%. As a result of applying a mathematical model, it has been indicated that the stress relaxation in the examined magnetorheological elastomer for the adopted time range (t = 3600 s) has a hyperbolic decline nature. The collected test results point to examined materials being characterised by extensive rheological properties, which leads to a conclusion that it is necessary to conduct further tests in this scope.

(1) Background: The study presents an assessment of the psychometric properties of the Polish version the Short Schema Mode Inventory (SMI) adaptation. (2) Methods: First, the original version of the scale was translated. Subsequently, a validity and reliability study was conducted on a sample of 240 patients and 400 non-patients. In particular: the factor structure of the inventory was checked, internal reliability and intercorrelations between subscales were tested, differences between the clinical and non-clinical groups in terms of the severity of each factor were examined, and construct validity was assessed by comparing the association of results with external variables. (3) Results: The results did not conclusively confirm the 14-factor structure postulated in the original scale. Nevertheless, relatively the best fit indices were obtained for such a model. Internal reliability for the 14 subscales was in the acceptable to excellent range. Correlations between subscales took moderate to high values. The existence of differences between the clinical and non-clinical groups and the construct validity were confirmed. (4) Conclusions: The psychometric evaluation performed is mostly similar to the results obtained for other adaptations, and the results entitle the inventory to be used for research and clinical purposes with the knowledge of its limitations.

Hepatitis B surface antigen (HBsAg) is not only the biomarker of hepatitis B virus (HBV) infection and expression activity in hepatocytes, but also contributes to viral specific T cell exhaustion and HBV persistent infection. Therefore, anti-HBV therapies targeting HBsAg to achieve HBsAg loss are key approaches for HBV functional cure. In this study, we found that YZH-106, a rupestonic acid derivative, inhibited HBsAg secretion and viral replication. Further investigation demonstrated that YZH-106 promoted the lysosomal degradation of viral L- and M-HBs proteins. Mechanistic study by Biacore and docking analysis revealed that YZH-106 bound directly to PreS2 domain of L- and M-HBsAg, thereby blocking their entry to the endoplasmic reticulum (ER) and promoting their degradation in cytoplasm. Our work thereby provide basis for design of novel compound therapy to target HBsAg against HBV infection.

This article presents a novel analysis of Indus Seal M-282 [1] excavated from Mohenjo-Daro, a key Indus Valley Civilization site. Utilizing the proposed Sindhu Prakrit alphabet, the study investigates the relationship between the seal's iconography and the inscribed text. By examining the potential for a close correlation between these elements, the analysis aims to decipher the meaning embedded within the seal's motifs, potentially offering new insights into Indus Valley communication and symbolism.

Based on the example of wintering waterbirds in the Baltic Sea, we show a method that is useful in setting priorities for species management. The Value Factor (VF) shows which species in the region are the most valuable and on which ones conservation measures need to focus. Every year 4,400,000 waterbirds winter in the Baltic. Among which the highest priority species are velvet scoter Melanitta fusca (VS, VF=153) and long-tailed duck Clangula hyemalis (LTD, VF=204): 74% and 40%, respectively, of the world populations and over 90% of the EU populations of both species spend the winter there. Management plans (MP) regulating the protection of marine Natura 2000 sites (MPA) and dedicated to the protection of VS and LTD have been implemented in 65% and 51%, respectively, of MPAs in the Baltic. Poland, a key country for the survival of these species, has not implemented a single MP despite the existence of documentation confirming their crucial importance for seaducks, and on the pressures occurring there. We suggest using the VF concept to define priority species. On this basis, it will be possible to identify gaps in the protection of the most seriously threatened species and implement conservation measures in the most appropriate sites

Overcoming terrain obstacles presents a major problem for people with disabilities or with limited mobility who are dependent on wheelchairs. An engineering solution designed to facilitate the use of wheelchairs are assisted propulsion systems. The objective of the research described in this article is to analyse the impact of the hybrid manual-electric wheelchair propulsion system on the kinematics of the anthropotechnical system when climbing hills. The tests were carried out on a wheelchair ramp with an incline degree of 4°, using a prototype wheelchair with a hybrid manual-electric propulsion system in accordance with the patent application P.427855. The test subjects were three people whose task was to propel the wheelchair in two assistance modes supporting manual propulsion. The first mode is hill climbing assistance, while the second one is assistance with propulsion torque in the propulsive phase. During the tests, a number of kinematic parameters of the wheelchair were monitored. An in-depth analysis was performed for the amplitude of speed during a hill climb and the number of propulsive cycles performed on a hill. The tests performed showed that when propelling the wheelchair only using the hand rims, the subject needed an average of 13 pushes on the uphill slope, and their speed amplitude was 1.8 km/h with an average speed of 1.73 km/h. The climbing assistance mode reduced the speed amplitude to 0.76 km/h, while the torque assisted mode in the propulsive phase reduced the number of cycles required to climb the hill from 13 to 6. The tests were carried out at various values of assistance and assistance amplification coefficient, and the most optimally selected parameters of this coefficient were presented in the results. The tests proved that electric propulsion assistance has a beneficial and significant impact on the kinematics of manual wheelchair propulsion when compared to a classic manual propulsion system when overcoming hills. In addition, assistance and assistance amplification coefficient were proved to be correlated to operating conditions and the user's individual characteristics.

The effectiveness of a hybrid technique for identifying seismic damage in planar, multistory, steel X or V-braced frames is demonstrated here through an example of a six-story frame. This proposed technique, referred to as “M and P”, combines the instrumental Monitoring (M) with Pushover analysis (P). According to the methodology, the diagram of stepping eigenfrequencies of the frame in the inelastic region is initially plotted against seismic roof displacement. The fundamental natural frequency detected via the monitoring process is then utilized in this key diagram to reveal the inelastic roof displacement that corresponds to the damage state of the steel braced frame. This displacement is subsequently used as the target in the pushover analysis, facilitating the identification of seismic damage in the existing steel braced frame. Finally, the damage image is correlated with the damage stiffness matrix of the frame at the same inelastic roof displacement. The investigation results indicate that combining instrumental monitoring with pushover analysis enables accurate identification of seismic damage potential in existing steel braced frames.

Emerging semiconductor devices often lack accurate analytical models. The same is usually true of any devices working under extreme conditions like cryogenic temperatures. The usual workaround involves the use of approximation models, usually based on lookup tables or neural networks individually fitted to measurement data. In the case of experimental devices or ones working under extreme conditions, the number of units available for measurement is limited. As a result, the number of approximation-model instances is too small to enable a statistical simulation of even middle-sized circuits, which is a necessary step in integrated-circuit design since it provides the realistic picture of the circuit’s behavior in the presence of manufacturing process variations. Approximation models using structure parameters as inputs do exist in the literature, but are only useful if the end user knows the statistical distributions of those parameters, which is not usually the case. We propose a technique based on generative machine learning, namely the variational autoencoder, that uses only a small sample of devices to capture the essential features of their I–V curves under process variations and subsequently generates an arbitrary number of similarly disturbed curves. The model trained on as few as 20 instances per device type is shown to precisely reproduce the distributions of period and power consumption of a ring oscillator.

The World Health Organization(WHO) in 2016 considered mHealth as: “the use of mobile wireless technologies including smart devices such as smartphones and smartwatches for public health” as an important resource for health services delivery and public health given their ease of use, broad reach and acceptance. WHO emphasizes the potential of this technology to increase access to health information, services and skills as well as promoting positive changes in health behaviors and management of diseases. In this regard, the capability of smartphones and smartwatches for m-health monitoring as well as verification of the patient the signal has become an important component of mHealth system. Most of the smartwatches could extract more than one bioelectrical signal therefore, therefore they provide suitable platform for extracting health data for e-monitoring. The existing approaches have not considered the integrity of data obtained from these smart devices. Therefore, it is important that the integrity of the collected data be verified continuously through user authentication. This could be done using any of the bioelectrical signals extracted and transmitted for e-monitoring. In this article, a smartwatch is used for extracting bioelectrical signal before decomposing the signal into sub-bands of Detail and Approximation Coefficient for user authentication. To select suitable features using biorthogonal wavelet decomposition of signal from a non-intrusive extraction, a detailed experiment is conducted extracting suitable statistical features from the bioelectrical signal from 30 subjects using different biorthogonal wavelet family. Ten features are extracted using Biorthogonal wavelet to decompose the signal into three levels of sub-band Detail and Approximation Coefficient and features extracted from each level the decomposed Detail and Approximation Coefficients. Comparison analysis is done after the classification of the extracted features based on the Equal Error Rate (EER). Using Neural Network (NN) classifier, Biorthogonal Wavelet Detail Coefficient Sub-band level 3 of bior1.1 achieved the best result of EER 13.80% with the fusion of the best sub-band three levels of bior1.1 achieving a better result of 12.42% EER.

The current work reports the upper bound of the state variable of the of the Pointwise Steady Fluid Flow Approximation (PSFFA) model of non-stationary M/Ek/1 queueing system.

Let R be a commutative ring with identity and m, n be positive integers. In this paper, we introduce the class of (m,n)-prime ideals which lies properly between the classes of prime and (m,n)-closed ideals. A proper ideal I of R is called (m,n)-prime if for a,b∈R, a^{m}b∈I implies either aⁿ∈I or b∈I. Several characterizations of this new class with many examples are given. Analougus to primary decomposition, we define the (m,n)-decomposition of ideals and show that every ideal in an n-Noetherian ring has an (m,n)-decomposition. Furthermore, the (m,n)-prime avoidance theorem is proved.

We report on metastable defects introduced in n-type 4H-SiC material by epithermal and fast neutron irradiation. The epithermal and fast neutron irradiation defects in 4H-SiC are much less explored compared to electron or proton irradiation induced defects. In addition to silicon vacancy (Vsi) and carbon antisite-carbon vacancy (CAV) complex, the neutron irradiation has introduced four deep level defects, all arising from the metastable defect, the M-center. The metastable deep level defects were investigated by deep level transient spectroscopy (DLTS), high-resolution Laplace DLTS (L-DLTS) and isothermal DLTS. The existence of the fourth deep level M4, recently observed in ion implanted 4H-SiC, has been additionally confirmed in neutron irradiated samples. The isothermal DLTS technique has been proven as a useful tool for studying the metastable defects.

A rapid synthesis of chiral sulfoxide-functionalized meta-terphenyl derivatives by a 2,5-[C4+C2] ring transformation reaction of pyrylium salts with in-situ generated enantio-merically pure .alpha.-sulfinylacetaldehydes is described. This synthetic method demonstrates for the first time the use of .alpha.-sulfinylacetaldehydes in a reaction sequence initiated by nu-cleophilic attack of pyrylium salts by .alpha.-sulfinylcarbanions to generate chiral aromatic systems. The method presented shows broad applicability starting with various methyl sulfoxides and a number of functionalized pyrylium salts, furnishing meta-terphenyls with complex substitution patterns from readily accessible starting compounds.

Abstract: Plasma hemopexin (HPX) is the key antioxidant protein of the endogenous clearance pathway that limits the deleterious effects of heme released from hemoglobin and myoglobin. During intra-vascular hemolysis, heme partitioning to protein and lipid increases as the plasma concentration of HPX declines. Therefore, the development of HPX as a replacement therapy during high heme stress could be a relevant intervention for hemolytic disorders. A logical approach to enhance HPX yield involves recombinant production strategies from human cell lines. The present study focuses on a biophysical assessment of heme binding to recombinant human HPX (rhHPX) produced in the Expi293FTM (HEK293) cell system. In this report, we examine rhHPX in comparison with plasma HPX using a systematic analysis of protein structural and functional characteristics related to heme binding. Analysis of rhHPX by UV/Vis absorption spectroscopy, circular dichroism (CD), SEC-HPLC and catalase-like activity demonstrated a similarity to HPX fractionated from plasma. In particular, the titration of HPX apo-protein(s) with heme was performed for the first time using a wide range of heme concentrations to model HPX-heme interactions to approximate physiological conditions (from extremely low to more than 2-fold heme excess). The CD titration data showed an induced bisignate CD Soret band pattern typical for plasma and rhHPX versions at low heme-to-protein molar ratios and demonstrated that further titration is dependent on the amount of protein-bound heme to the extent that the arising opposite CD couplet results in a complete inversion of the observed CD pattern. The data generated in this study suggests more than one binding site in both plasma and rhHPX. Further, our study provides a useful analytical platform for detailed characterization of HPX-heme interactions and potentially, novel HPX fusion constructs.

Epidemiological studies indicate that skipping breakfast as a universal behavior, may have adverse effects on cardiovascular diseases [CVDs}and metabolic diseases. However, eating breakfast regularly, may increase satiety, thereby reducing overeating later in the day which prevents weight gain. Recent studies indicate that skipping breakfast increases the risk of obesity, metabolic syndrome, hypertension, hypercholesterolemia, type 2 diabetes mellitus (T2DM), coronary artery disease (CAD), and cardiovascular mortality as well as all-cause mortality. However, many studies also reported that regular taking of breakfast decreases the risk of CVDs and T2DM and all-cause mortality. Previous studies reported that heavy breakfast, in particular eating western diet may increase circadian rhythm of CVDs and sudden cardiac death. It seems that those who do not eat breakfast, they tend to eat refined and sweetened products, possibly, more in the night resulting in to greater risk of CVDs and T2DM. Breakfast skipping and eating in the night, may be associated with circadian misalignment in the central and peripheral clocks, leading to oxidative stress and inflammation. Increased systemic inflammation damages the adipocytes, beta cells of pancreas, endothelial cells and smooth muscle cells as well as neurons, which may produce dysfunction in these cells resulting in to related diseases. The beneficial effects of breakfast, may also be, at least in part, due to nutrient dense foods rather than time of eating. Eating regular breakfast, in particular rich in Indo-Mediterranean foods; vegetables, whole grains, fruits, spices and nuts may be protective against circadian increase in oxidative stress in the morning, resulting in to significant decline in the risk of CVDs and T2DM.

Pulmonary infections with Mycobacterium avium occur in susceptible individuals following exposure to the bacterium in the environment, where it often persists in biofilms. Many methods have been used to generate biofilms of M. avium, and it is unknown whether different approaches generate similar structures and cell phenotypes. To make a parallel comparison of in vitro biofilm ultrastructure, extracellular matrix (ECM) composition, and drug susceptibility of biofilm resident bacteria, we used two published methods to generate M. avium biofilms: four week incubation in M63 medium or 24 hour exposure to dithiothreitol (DTT). Scanning electron microscopy revealed differences in biofilm ultrastructure between the two methods, including variation in appearance of ECM materials and morphology of resident cells, while light microscopy and staining with calcofluor white indicated that both biofilms contained polysaccharides characteristic of cellulose. Measuring susceptibility of biofilms to degradation by enzymes suggested differences in structurally important ECM molecules, with DTT biofilms having important protein and, to a lesser extent, cellulose components, and M63 biofilms having moderate protein, cellulose, and DNA components. Both biofilms conferred resistance to the bactericidal effects of amikacin and clarithromycin, with resident cells being killed at &gt;10-fold lower rates than planktonic cells at almost all concentrations. Though these comparisons indicate differences in biofilm responses by M. avium under differing conditions, they also suggest common features of biofilm formation including cellulose production and antimicrobial resistance.

The topological index is a numerical quantity based on the characteristics of various invariants or molecular graph. For ease of discussion, these indices are classified according to their logical derivation from topological invariants rather than their temporal development. Degree based topological indices depends upon the degree of vertices. This paper computes degree based topological indices of Bismuth Tri-Iodide chains and sheets with the help of M-polynomial.

The motivation of this work is to investigate experimentally the influence of non-thermal plasma (NTP) application on the reaction kinetics of atmospheric pressure steam gasification of charcoal using a thermostatically controlled drop tube reactor. A gliding-arc generator provides about 1 kW electrical power NTP. For comparison thermal gasification is investigated under comparable flow and specific energy input conditions providing additional heat to the steam. Optical temperature measurement 20 cm flow down of the NTP zone is utilized to characterize the specific enthalpy of the reactive flow. The composition of produced syngas is measured by a gas analyzer and used for the calculation of gas flow rates. The results show a NTP-enhancement on the production of individual syngas components (H2, CO, CH4), especially on hydrogen production by around 39%. The syngas-based carbon conversion and hydrogen release are calculated from the carbon and hydrogen balance between the correspondent content in syngas and in the feedstock. The NTP promoted the carbon conversion and hydrogen release by 25% and 31%, respectively. The first-order reaction kinetics are determined by data-fitting in an Arrhenius diagram. The plasma enhanced the reaction rate coefficients by 27%. Based on experimental results and other literature, possible plasma-induced reactions are proposed.

Current conventional methods of evaluating microstructures are characterized by a high degree of subjectivity and a lack of reproducibility. Modern machine learning (ML) approaches have already shown great potential in overcoming these challenges. Once trained with representative data in combination with an objective ground truth, the ML model is able to perform a task properly in a reproducible and automated manner. However, in highly complex use cases, it is often not possible to create a definite ground truth. This study addresses this problem using the underlying showcase of microstructures of highly complex quenched and quenched and tempered (Q/QT) steels. A patch-wise classification approach combined with a sliding window technique provides a solution for segmenting entire microphotographs where pixel-wise segmentation is not applicable due to the problem of reproducibly creating unambiguous training masks. Using correlative microscopy, consisting of light optical microscope (LOM) and scanning electron microscope (SEM) micrographs as well as corresponding data from electron backscatter diffraction (EBSD), a training dataset of reference states that covers a wide range of microstructures was acquired in order to train accurate and robust ML models. Despite the enormous complexity associated with the steels treated here, classification accuracies of 88.8% in the case of LOM images and 93.7% for high-resolution SEM images were achieved. These high accuracies are close to super-human performance, especially in consideration of the reproducibility of the automated ML approaches compared to conventional methods based on subjective evaluations through experts.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Sepsis is defined as life-threatening organ dysfunction caused by a dysregulated host response to an infection. Recent in-vitro studies have investigated the effects of CytoSorb hemoadsorption on endothelial function in sepsis showing a reduction in markers of endothelial dysfunction, but to this day there is a lack of clinical studies showing whether this approach could actually positively influence the disturbed vascular barrier function in septic conditions. We analyzed the data on administered fluid volumes and catecholamines to determine the potential benefit of CytoSorb hemoadsorption therapy on endothelial function in a clinical scenario. We performed a retrospective analysis of 124 septic shock patients who had undergone adjunctive treatment with CytoSorb hemadsorption therapy. We collected volume requirements, and calculated the volume balance within different time periods to obtain an assumption on the stability of the vascular barrier. We also calculated catecholamine requirements. With regard to the entire study cohort our findings revealed a significant reduction in fluid balance at 72 hours (T72) compared to both baseline (T0) and the 24-hour mark (T24). Fluid balances from T72 – T0 were significantly lower in hospital survivors compared to non-survivors. Patients who received a second catecholamine had a significantly lower in-hospital mortality. Our findings showed that use of hemoadsorption therapy results in a reduced positive fluid balance paralleled by reductions in vasopressor needs suggesting a positive effect on endothelial integrity. These results, derived from a large cohort of patients, provide valuable insights that may greatly improve our understanding of the multiple effects of hemoadsorption treatment in septic shock patients.

Sarcosine (N-methylglycine), a glutamatergic modulator, reduces the primary negative symp-toms of schizophrenia. These beneficial changes might be mediated by trophic factors such as ep-idermal growth factor (EGF). We assessed associations between initial serum EGF levels or changes in serum EGF levels and symptom severity during the addition of sarcosine to stable an-tipsychotic treatment and thereby evaluate the associations between glutamatergic modulation, clinical changes and peripheral EGF concentrations. 58 subjects with a diagnosis of chronic schizophrenia with dominant negative symptoms, stably treated with antipsychotics completed a prospective 6-month, randomized, double-blind, placebo-controlled study. Subjects received orally 2 grams of sarcosine (n=28) or placebo (n=30) daily. Serum EGF levels and symptom se-verity (using Positive and Negative Syndrome Scale - PANSS and Calgary Depression Scale for Schizophrenia - CDSS) were assessed at baseline, 6 weeks, and 6 months follow-up. Augmenta-tion antipsychotic treatment with sarcosine had no effect on EGF serum levels at any time-points. Only the sarcosine group showed a significant improvement in negative symptoms, general psy-chopathology subscales, and the overall PANSS score. We found reduction of serum EGF levels in the placebo group, but levels in the sarcosine remained stable during the study. Our data indicate that improvement in negative symptoms due to sarcosine augmentation is not mediated by EGF, but effective treatment may induce the production or block the decrease in EGF concentrations, which indicates the neuroprotective effect of treatment and confirms the relationship between neuroprotection and EGF levels.

Over the years, chitosan has been the subject of numerous studies and has gained significant popularity as a biomaterial due to its various characteristics, including biocompatibility, biodegradability, and bioactivity. In this work, chitosan fibres surface was modified with ursolic acid to improve their antibacterial properties by wet impregnation method. Five specimens of chitosan fibres were immersed in ursolic acid (UA) solution for varying immersion times of 1, 2, 4, 6, and 8 hours. Characterization was carried out by means of FTIR, SEM, UV-Vis spectroscopy; the results indicated an ongoing chemical reaction between chitosan and ursolic acid resulting in changes to the chemical structure. After 2 hours, the absorbance ratio remained constant; suggesting that the reaction had reached completion and the chemical structure of the sample remained stable. Antibacterial tests were performed on the resulting chitosan fibres against two bacterial strains. The fibres without ursolic acid did not exhibit any noteworthy antibacterial activity against either strain. However, the chitosan fibres modified with ursolic acid showed significant and almost strong antibacterial activity against the Gram-positive strain, S. aureus. These results suggest that chitosan fibres modified with ursolic acid could have potential applications as antibacterial materials, particularly against Gram-positive bacteria.

Tardive dyskinesia (TD) is a phenomenon predominantly observed as a result of the long-term use of dopamine receptor blockers (antipsychotics). TD is a group of involuntary, irregular hyperkinetic movements, mainly in the muscles of the face, eyelid muscles, lips, tongue, and cheeks, and less frequently in the limbs, neck, pelvis, and trunk. In some patients, TD takes on an extremely severe form, massively disrupting functioning, moreover, causing stigmatization and suffering. Deep brain stimulation (DBS), a method used, among others, in Parkinson's disease, is also an effective treatment for TD and often becomes a method of last resort, especially in severe, drug-resistant forms. The procedure is relatively new in TD, so the available reliable clinical studies are few and consist mainly of case reports. Unilateral and bilateral stimulation of two sites has proven efficacy in TD treatment. Most authors describe stimulation of the globus pallidus internus (GPi); less frequent descriptions involve the hypothalamic nucleus (STN). In the present paper, we provide up-to-date information on the stimulation of both mentioned brain areas. We also compare the efficacy of the two methods by comparing the two available studies, which included the largest groups of patients. Although GPi stimulation is more frequently used clinically, our initial analysis indicates comparable results (reduction of involuntary movements) with STN DBS.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

The seismic damage in reinforced concrete bridges is identified in this study using the "M and P" hybrid technique initially developed for planar frames. The proposed methodology involves a series of pushover and instantaneous modal analyses with a progressively increasing target deck displacement along the longitudinal direction of the bridge. From the results of these analyses, the diagram of the instantaneous eigenfrequency of the bridge, ranging from the health state to near collapse, is plotted against the inelastic seismic deck displacement. By pre-determining the eigen-frequency of an existing bridge along its longitudinal direction through "monitoring and frequency identification", the target deck displacement corresponding to the damage state can directly be found from this diagram. Subsequently, the damage can be identified by examining the results of the pushover analysis at the step where the target deck displacement is indicated. The effectiveness of this proposed technique is evaluated in the context of multiple span bridges with unequal pier heights, illustrated through an example of a four-span bridge. The findings demonstrate that the damage potential in bridge piers can be successfully identified by combining the results of a monitoring process and pushover analysis.

It has been more than a century since Erlang published his paper in 1909. The classical queueing system for the M/D/c queue has been investigated by many authors. The key is to find the roots of an equation using explicit or numerical methods. We present an alternate form of explicit solution(s) of this/these root(s) using the Lambert-W function in this paper. In addition, the unsaturated probabilities of the number of customers in the system is derived explicitly in terms of this/these root(s). Finally, the mean number of customers in the system and the mean queueing delay are obtained from these probabilities. The exact queueing delay formula for the M/D/c queue is expressed in closed-form in terms of the root(s). Numerical results show that they are in excellent agreement with the numerical results published by Seelen, Tijms and Van Hoorn.

Let R be a commutative ring and m, n be positive integers. We define a proper submodule N of an R-module M to be (m,n)-closed if for r∈R and b∈M, r^{m}b∈N implies rⁿ∈(N:_{R}M) or b∈N. This class of submodules lies properly between the classes of prime and primary submodules. Many characterizations, properties and supporting examples concerning this class of submodules are provided. The notion of (m,n)-modules is introduced and characterized. Furhermore, the (m,n)-closed avoidance theorem is proved. Finally, the (m,n)-closed submodules in amalgamated modules are studied.

Acid proteins capable of nucleating Ca2+ and displaying aggregation capacity play key roles in the formation of calcium carbonate biominerals. EF-hands are among the largest Ca2+-binding motif in proteins. Gad m 1, an Atlantic cod β-parvalbumin isoform, is a monomeric EF-hand protein that acts as a Ca2+ buffer in fish muscle and is able to form amyloids under acidic conditions. Since nucleating Ca2+ protein have a propensity to form extended β-strand structures, we wondered whether amyloid assemblies of a protein containing refolded EF-hand motifs were able to influence the in vitro calcium carbonate crystallization. Here we have used the Gad m 1 chain as model to generate monomeric and amyloid assemblies and analyze their effect on in vitro calcite formation. We found that only amyloid assemblies alter calcite morphology.

Exploring new ways to represent and discover organic molecules is critical for developing novel therapies. With recent advances in bioinformatics, virtual screening of databases is possible. However, biochemical data must be encoded using computer algorithms to make them machine-readable, taking into account distance and similarity measures to support tasks such as similarity searching. Motivated by the ubiquity of the carbon element and the structured patterns that emerge, we propose a parametric approach to molecular encodings of carbon-based multilevel atomic neighborhoods. It implements a walk along the carbon chain of an organic molecule to compute different representations of its feature encoding in the form of a binary or numerical array that can be exported later into an image. Resulting encodings are reproducible and readily formatted for various domain tasks including machine learning tasks. This approach was evaluated using a 10-fold stratified cross validation for binary classification with eight data sets and six different encodings (384 models) in the domain knowledge of cell-penetrating peptides. The parametric approach is built on open-source software and is implemented as a Python package (cmangoes). Source code and documentation are available at https://github.com/ghattab/cmangoes.

The current study characterizes the transient M/M/1 queue manifold info-geometrically, through devising Fisher Information matrix(FIM) and its inverse(IFIM). Additionally, the impact of stability on the existence of IFIM and explore the geodesic equations of motion has been revealed. More potentially, the paper discusses some info-geometric applications to Machine Learning are highlighted. Closing remarks with some challenging open problems combined with the next phase of research are given.

Shape memory alloys (SMA) are becoming a more important factor in actuation technology. Due to their unique features, they bring the potential to safe weight, installation space and reduce energy consumption. The system integration of the generally small diameter NiTi wires is an important cornerstone for the emerging technology. Crimping, a common method for the mechanical and electrical connection of SMA wires, has several drawbacks when it comes to miniaturization and high force outputs. For high force applications for example, multiple SMA wires in parallel are needed to keep actuation frequencies high, while scaling up the actuation force. To meet these challenges, the proposed study deals with the development of a resistance welding process for manufacturing NiTi wire bundles. The wires are welded to sheet metal substrate, resulting in promising functional properties and high joint strengths. The welding process benefits from low cost, easy to control parameters and good automation potential. A method for evaluating the resistance welding process parameters is presented. With these parameters in place, a manufacturing process for bundled wire actuators is discussed and implemented. The welded joints are examined by peel tests, microscopy, and fatigue experiments. The performance of the manufactured bundle actuators is demonstrated by comparison to a single wire with the same accumulated cross-sectional area.

We summarize structural instabilities exhibited by the one dimensional (1D) (arene)2X family of organic conductors in relation with their electronic and magnetic properties. With a charge transfer of one electron to each anion X these salts exhibit a quarter-filled (hole) conduction band located on the donor stacks. Compounds built with donors such as fluorenthene and perylene derivatives and anions X such PF6 or AsF6 exhibit a high temperature (TP~170K) conventional Peierls transition which is announced by a sizeable regime of 1D 2kF charge density wave fluctuations (kF is the Fermi wave vector of the 1D electron gas located on Per stacks). Surprisingly, and probably because of the presence of a multi-sheet warped Fermi surface, the Peierls transition is considerably reduced in the perylene series α-(Per)2[M(mnt)2] where X is the dithiolate molecule with M=Au, Cu, Co and Fe. A special attention is devoted in this paper to physical properties of α-(Per)2[M(mnt)2] salts which with M=Pt, Pd and Ni incorporate segregated S=1/2 1D antiferromagnetic (AF) dithiolate stacks with 1D metallic Per stacks. We analyse conjointly the structural and magnetic properties of these salts in relation with the 1D spin-Peierls (SP) instability located on the dithiolate stacks. We show that the SP instability of the Pd and Ni derivatives occurs in the classical (adiabatic limit) while the SP instability of the Pt derivative occurs in the quantum (anti-adiabatic limit). Furthermore we show that in the Pd and Ni derivatives frustrated 1st neighbour direct and 2nd neighbour indirect (through a fine tuning with the mediated 2kF RKKY coupling interaction on Per stacks) AF interactions add their contribution to the SP instability to open a singlet-triplet gap. Our analysis of the data show unambiguously that magnetic α-(Per)2[M(mnt)2] salts are a typical realization of the physics predicted for two chain 1D Kondo lattices.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

Carbon nanotubes (CNTs) can be considered as semi-rigid all-carbon polymers. However, unlike conventional polymers that can form 3D networks such as hydrogels or elastomers through crosslinking with each other in solution, the cylindrical carbon lattice of CNTs was not believed to be directly crosslinkable in solution until our recent discovery of UV-defluorination driven direct CNT crosslinking. In this study, we further reveal that the UV-defluorination-driven crosslinked CNTs are metastable and can decompose more readily than fluorinated or pristine CNTs upon exposure to Raman laser irradiation. Specifically, we investigate the stability of UV-defluorinated single-walled and multi-walled fluoro-nanotubes using Raman spectroscopy under controlled varying laser power. The results indicate that both the defluorinated single-walled and multi-walled CNTs are thermally less stable than pristine CNTs or untreated fluorinated CNTs, which can be attributed to the strains on the crosslinking bonds created from the curved carbon lattice of linked CNTs. This instability, particularly evident under high-power laser irradiation, leads to combustion processes ignited at relatively lower temperatures that cause an extended burned area centered on the laser spot, offering potential future applications as mechanically robust, lightweight materials with feasible post-use degradation options.

Quinacridone (QA) and 2,9-dimethylquinacridone (DQA) are synthetic substances suitable as a hard, abrasion-resistant, self-organizing gliding layer on ice, snow, and water. For sustainable use, a large number of parameters must be considered to demonstrate that these non-biogenic substances and their by-products and degradation products are harmless to humans and the environment in the quantities released. For this task, available experimental data are used and supplemented for all tautomers by numerous relevant physical, chemical, toxicological and ecotoxicological estimated values based on various Quantitative Structure Activity Relationship (QSAR) methods. On the one hand, the low solubility of QA and DQA leads to stable gliding layers and thus low abrasion and uptake by plants, animals, and humans. On the other hand, the four hydrogen bond forming functional groups per molecule allow nanoparticle decomposition and enzymatic degradation in natural environments. All available data justify a sustainable use of QA and DQA as a gliding layer. The assessment of the toxicological properties is complemented with an investigation of the size and morphology of DQA particles as well as field tests indicating an excellent performance as a gliding layer on snow.

While significant efforts have been made to recycle metals like lithium or cobalt for sustainable development in the battery industry, other high-value materials in the renewable energy sector, such as fluorinated carbon nanotubes (FCNTs), have not been adequately explored for re-utilization after their quality has been downgraded. FCNTs are expensive and energy-intensive to produce, making their sustainable use crucial. This study explores the potential of reusing quality-downgraded fluorinated carbon nanotubes (QD-FCNTs) as eco-friendly nano-additives in microgel composites for water retention applications. By employing a surface treatment process that avoids additional energy costs and environmentally harmful chemicals, we successfully enhanced the interaction between QD-FCNTs and microgels. This treatment significantly improved water retention time by reducing rapid evaporation, enabling sustained water release. Our findings demonstrate a promising avenue for the sustainable application of quality-downgraded fluorinated carbon nanotubes in agricultural and environmental technologies.

Decision-making using evidence-based practice (EBP) is generally universally accepted by nurses. Such acceptance may affect the personnel’s behaviour towards patients, which is also demonstrated by taking into consideration the patient’s preferences, including the patient’s spiritual needs, in the care plan. The provision of such care requires the development of an attitude of approval and an adequate level of communicative competence, which will enable the actual implementation of the EBP. The purpose of our study was to assess the perception of spirituality and the nurse’s role in providing spiritual care, as well as the perception of the significance of communication skills in the approval of EBP in professional practice. A multi-centre cross-section study was conducted on a population of 1176 participants (459 undergraduate (Bachelor programme, BP) and 717 postgraduate students (Master programme, MP)) from 10 medical universities in Poland. Three tools were used in the study to evaluate the participants’ approach: Evidence-Based Practice Competence Questionnaire (EBP-COQ), The Spirituality and Spiritual Care Rating Scale (SSCRS), and Communication Skills Attitude Scale (CSAS). Structural equation modelling was used for the analysis. An analysis of structural equations revealed the presence of positive relationships of the attitude to spiritual care and the role of communicative competences with the approach to EBP regardless of the cohort. A significant difference was found related to the influence of age on the attitude toward learning communicative competences. The approval in this respect was observed to decrease with age in the MP group. Increasing approval of EBP requires strengthening the approach to activity-centred spiritual care, with the simultaneous development of a positive attitude towards learning communicative competences. The model reveals the need to integrate a humanistic approach with EBP, which can be achieved by planning different interventions in different groups of recipients: nurses, academic teachers and students.

Clarifying the impact mechanism of digital transformation of enterprises on the M&A efficiency of listed companies can provide a factual basis for improving capital market regulatory policies. Taking the mergers and acquisitions of listed companies from 2007 to 2021 as a research sample, the influence mechanism of the digital transformation degree of companies on their M&A efficiency was studied. The research results show that the digital transformation of listed companies will improve their M&A efficiency. Digital transformation will reduce the degree of mispricing of stocks of M&A companies, curb conflicts between managers and agents of M&A companies, and improve their M&A efficiency. Further research finds that the promotion effect of digital transformation on M&A efficiency is more significant in non-state-owned companies, with a higher degree of financing constraint and high analyst attention. In the future, regulatory authorities should actively promote the digital transformation of listed companies, curb mispricing and management agency problems in the capital market with digital governance, and improve the efficiency of mergers and acquisitions in the capital market.

Purpose. Moraxella is an ocular bacterial pathogen isolated in cases of keratitis, conjunctivitis, and endophthalmitis. Gram-negative brick-shaped diplobacilli from ocular specimens, and slow growth in culture, are early indications of Moraxella ocular infection; however, identifying Moraxella to species can be complex and inconsistent. Methods. In this study, bacteria consistent with Moraxella were identified to species using: 1) DNA sequencing coupled with vancomycin susceptibility, 2) MALDI-TOF Mass Spectrometry, and 3) Biolog ID System. Study samples consisted of 9 ATCC Moraxella controls, 82 isolates from keratitis, 21 isolates from conjunctivitis, and 4 isolates from endophthalmitis. Results. The ATCC controls were correctly identified. For keratitis, 66 (80.5%) were identified as M. nonliquefaciens, 7 (9.0%) as M. lacunata, 5 (6%) as M. osloensis, 2 (2.5%) as Acinetobacter lwoffi, 1 (1.0%) as M. bovis/nonliquefaciens, and 1 (1.0%) as M. osloensis/nonliquefaciens. For conjunctivitis, 9 (43.0%) were identified as M. osloensis, 6 (29.0%) as M. nonliquefaciens, 3 (14.3%) as Roseomonas, 2 (9.5%) as Acinetobacter (parvus, junii), and 1 (4.5%) as M. catarrhalis/M. nonliquefaciens. From endophthalmitis, 3 of 4 of the isolates were M. nonliquefaciens. Overall, M. nonliquefaciens and M. osloensis were identified in 70% (75 of 107) and 13% (14 of 107) of cases, respectively, totaling 83% (89 of 107). Conclusions. M. nonliquefaciens and M. osloensis are important bacterial pathogens of the eye as determined by DNA sequencing, MALDI-TOF MS, and Biolog. Although Moraxella catarrhalis is a clinical pathogen, other species of Moraxella appear to have a prominent role in eye infections.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

The paper deals with the problem of choosing the best O&M strategy for wind power plants. Current maintenance theory considers just production opportunities and minimizes the maintenance costs, but with the liberalization of the electricity market also the electricity price has become an important variable to take into account in the O&M scheduling. Another important variables that is often neglected by the existing maintenance theory is the weather condition. This paper proposes a new strategy that takes into account the electricity price and weather conditions, improves the expected profit of the systems, and reduce the overall maintenance and logistic costs. The maintenance schedule is formalized as an optimization problem where the discounted cumulative profit of a wind generation portfolio in a fixed-time horizon (e.g. two years ahead), subject to the technologically-derived maintenance time constraints is optimized. Both the theoretical and computational aspects of the proposed O&M strategy are discussed. Results show that taking into account market and weather opportunities in the design of the maintenance strategy, it is possible to achieve a more complete scheduling for a given set of wind power plants.

Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I-V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modelled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 \% to the total degradation rate.

Rising antimicrobial resistance (AMR) in Salmonella serotypes host-adapted to cattle is of increasing concern to the beef and dairy industry. The bulk of the existing literature focuses on AMR post-slaughter. In comparison, the understanding of AMR in Salmonella among pre-harvest cattle is still limited, particularly in Texas, which ranks top five in beef and dairy exports in the United States; inherently, the health of Texas cattle has nationwide implications for the health of the United States beef and dairy industry. In this study, long-read whole genome sequencing and bioinformatic methods were utilized to analyze antimicrobial resistance genes (ARGs) in 98 isolates from beef and dairy cattle in the Texas Panhandle. Fisher exact tests and elastic net models accounting for population structure were used to infer associations between ARGs and antimicrobial phenotypic profiles and metadata. Gene mapping was also performed to assess the role of mobile genetic elements in harboring ARGs. ARG were found to be statistically different between the type of cattle operation and Salmonella serotypes. Beef operations were statistically significantly associated with more resistance genes compared to dairy operations. Salmonella Heidelberg, followed by Salmonella Dublin isolates, were associated with the most ARGs. Additionally, specific classes of ARGs were only present within mobile genetic elements.

With the widespread use of the Internet of Things, underwater control and monitoring systems for purposes such as ocean data sampling, natural disaster prevention, underwater surveillance, submarine exploration, and the like have become a popular and challenging topic in computers. So far, various topology control and routing solutions have been proposed for these networks. However, as technology expands and applications grow, so does the need for a stable underwater communication platform. On the other hand, underwater communication is associated with challenges such as node mobility, long propagation delays, low bandwidth, limited resources, and high error rates. In this research, for the first time, a topology control platform based on the RPL tree is modelled by applying its structural changes underwater. The proposed RPLUW methods in the case of RPLUWM fixed nodes are introduced to support the mobility of nodes underwater. Flexible objective functions, utilisation of decision-making systems, and application of control schedules in these methods have increased network life, reduced overhead, and increased node efficiency. The simulation results of the proposed method, in comparison with recent methods in this field, show an increase in network efficiency.

The Drosophila spermatogenesis has the renewal of germline stem cells, meiosis of spermatocytes, and morphological transformation of spermatids into mature sperm. We previously demonstrated that Ocnus (ocn) plays an essential role in spermatogenesis. ValRS-m (Valyl-tRNA synthetase, mito-chondrial) gene was downregulated in ocn RNAi testes. By hatchability testing, we found that ValRS-m-knockdown induced complete sterility of male flies. We also concluded that ValRS-m-knockdown inhibited the transition from spermatogonia to spermatocytes and caused accumulated spermatogonia in testes. To understand the intrinsic reason for this destruction, we further conducted transcriptome sequencing analysis in ValRS-m RNAi testes. A total of 7710 dif-ferentially expressed genes (DEGs) were identified to have at least a 2-fold change with a p-value of

In order to investigate the coordination chemistry of O-alkyl N-aryl thiocarbamate ligands, BiI3 has been reacted with two equivalents of MeOC(=S)N(H)Ph in MeCN solution to afford the dinuclear title compound complexes [{I2Bi(μ2-I)2BiI2}{1-MeOC(=S)N(H)Ph}4] 1. Compound 1 has been characterized by IR, UV and NMR spectroscopy, the dinuclear framework has be ascertained by a single-crystal X-ray diffraction study performed at 100 K.

Cyclin dependent kinase 1 (CDK1) has been primarily identified as a key cell cycle regulator in both mitosis and meiosis. Recently, an extramitotic function of CDK1 emerged when evidence was found that CDK1 is involved in many cellular events that are essential for cell proliferation and survival. In this review we summarize the involvement of active CDK1 in the initiation and elongation steps of protein synthesis in eukaryotes. During its activation CDK1 influences the initiation of protein synthesis, promotes the activity of specific translational initiation factors and affects the functioning of a subset of elongation factors. Our review provides insights into gene expression regulation during the transcriptionally silent cell cycle/M-phase and describes quantitative and qualitative translational changes based on the extramitotic role of the cell cycle master regulator CDK1, to optimize temporal synthesis of proteins to sustain division-related processes: mitosis and cytokinesis.

To investigate this suitability of Black Mustard (Brassica Nigra L.) and Camelina (Camelina Sativa L.) for pulp manufacturing the nitrate-alkaline method was used. The non-wood plants were characterized by chemical analysis, especially lignin, cellulose, ash, extractives and alpha-, beta-, gamma-cellulose. The pulp was cooked in 6% nitric acid and then underwent the extraction by 5% sodium-hydroxide and neutralized by 1% acetic acid. The cooked pulp was characterized by delignification degree – Kappa number. The laboratory sheets were made from this cooked pulp and they were characterized by tensile index, breaking length, smoothness and compared with commonly available papers.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

The characteristics of powders on a bulk scale are heavily influenced by both the material properties and the size of their primary particles. Throughout the stages of storage and transportation in the powder processing industry, various forms of deformation and stress, such as pressure and shear, impact these materials. Recognizing the point at which a powder undergoes yielding becomes particularly significant in numerous applications. There are also times when you need to understand the level of stress needed to maintain it. Measurement of powder yield and flow properties remains a challenge and is addressed in this study. As part of the CALIPER collaborative project, a number of shear experiments were performed using two shearing devices: Schulze ring shearing device and Anton Paar Powder Cell (APCC). These experiments have three purposes: i) Test reproducibility/consistency between two shear devices and test protocols. ii) To relate bulk behavior to microscopic particle properties, focusing on bulk density and thus the effect of cohesion between particles; iii) Investigate the influence of the temperature of heated powders on the powder flow properties, which is important for the industrial reactors. Interestingly, for samples with small particle size, bulk cohesion increases slightly, but bulk friction increases significantly, because of particle interaction effects. The experimental data not only provide useful insight into the role of microscopically attractive van der Waals gravitational and/or compressive forces on the macroscopic flow behavior of bulk powders, but also have industrial relevance. We also provide a robust datas of cohesive and attritional fine powder for silo design used for calibration and validation of silos, models and computer simulations.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

Cells respond to DNA double-strand breaks by initiating DSB repair and ensuing a cell cycle checkpoint. The primary responder to DSB repair is non-homologous end joining, an error prone repair pathway. However, when DSBs are generated after DNA replication in the G2 phase of the cell cycle, a second DSB repair pathway, homologous recombination, can come into action. Both ATM and ATR are important for DSB-induced DSB repair and checkpoint responses. One method of ATM and ATR working together is through the DNA end-resection of DSBs. As a readout and marker of DNA end-resection, RPA is phosphorylated at Ser4/Ser8 of the N-terminus of RPA32 in response to DSBs. Here, the significance of RPA32 Ser4/Ser8 phosphorylation in response to DNA damage, specifically in S phase to G2 phase of the cell cycle is examined. RPA32 Ser4/Ser8 phosphorylation in G2 synchronized cells is necessary for increases in TopBP1 and Rad9 accumulation on chromatin and full activation of the ATR-dependent G2 checkpoint. In addition, our data suggest RPA Ser4/Ser8 phosphorylation modulates ATM-dependent KAP-1 phosphorylation and Rad51 chromatin loading in G2 cells.

In present paper, spatial Minkowski Pythagorean Hodograph (MPH) curves are characterized with Rational Rotation Minimizing Frames (RRMFs). We define Euler-Rodrigues Frame (ERF) for MPH curves and by means of this concept, we reach the definition of MPH curves of type (n, m). Expressing the conditions provided by these curves in the form of Minkowski-Hopf map that we define, it is aimed to establish a connection with the Lorentz force which occurs during the process of Computer Numerical Control (CNC) type sinker Electronic Discharge Machines (EDMs). This approach is reinforced by split quaternion polynomials. Finally, we give conditons satisfied by MPH curves of low degree to be type (n, m) and construct illustrative examples.

In this work, we derive the spectral efficiency, secrecy outage probability, and bit error rate of a communication system assisted by a large intelligent surface (LIS). We consider a single-antenna user and an array of antennas at the transmitter side and the possibility of a direct link between transmitter and receiver. Additionally, there is a single-antenna eavesdropper with a direct link to the transmitter, which is modeled as a Nakagami-m distributed fading coefficient. The channels from transmitter to the LIS and from the LIS to the user may or may not have the line-of-sight (LoS) and are modeled by the Nakagami- m distribution. Moreover, we assume that the LIS elements perform non-ideal phase cancellation leading to a residual phase error that assumes a Von Mises distribution. We show that the resulting channel can be accurately approximated by a Gamma distribution whose parameters are analytically estimated using the moments of the equivalent signal-to-noise ratio. We also provide an upper bound for the error probability for M-QAM modulations. With the derived formulas, we analyze the effect of the strength of the LoS link by varying the Nakagami parameter, m.

Aim: Evaluation of role of supplementation of omega-3 polyunsaturated fatty acids on endothelial function in patients with metabolic syndrome. Methods: Total of 80 patients with metabolic syndrome were enrolled to two groups. We evaluated endothelial function in subjects before and after three-month treatment with omega-3 polyunsaturated fatty acids in dose 2.4g daily (800mg 3 times a day) vs placebo. Using the Endo-PAT2000 device (Itamar Medical Ltd. Caesarea, Israel), reactive hyperemia index – a parameter of endothelial function and augmentation index– a parameter of arterial stiffness were measured. Plasmatic level of glutation peroxidase, homocysteine, apolipoprotein B and lipoprotein (a) were also evaluated. Results: The average values of reactive hyperemia index before the treatment with n-3PUFA was 1.62 ± 0.42 , whereas 1.96 ± 0.62 at the end of the study (p<0.005). Augmentation index changed from 14.66 ± 19.55 to 9.21 ± 15.64 after the treatment (p=0.003). We also observed statistically significant decrease of apolipopotein B (0.94 ± 0.36 vs 1.13 ± 0.35, p = 0.001) and homocysteine (19.31 ± 5.29 vs. 13.78 ± 3.05, p = 0.001) and increase of the glutathion perxidase plasma levels (41.65 ± 8.90 vs. 45.20 ± 8.01), p=0.001. Conclusion: We have observed significant improvement of the endothelial function in subjects with metabolic syndrome treated with omega-3 polyunsaturated fatty acids in dose 2.4g daily.

Mesenchymal stem cells (MSCs) hold immense therapeutic potential due to their regenerative and immunomodulatory properties. However, to utilize this potential, it is crucial to optimize their in vitro cultivation conditions. Three-dimensional (3D) culture methods using cell-laden hydrogels aim to mimic the physiological microenvironment in vitro, thus preserving MSC biological functionalities. Cellulosic hydrogels are particularly promising due to their biocompatibility, sustainability, and tunability in terms of chemical, morphological, and mechanical properties. This study investigated the impact of (1) two physical crosslinking scenarios for hydrogels derived from anionic cellulose nanofibers (CNF) used to encapsulate adipose-derived MSCs (adMSCs) and (2) physiological culture conditions on the in vitro proliferation, differentiation, and extracellular vesicle (EV) production of these adMSCs. Our results revealed that additional Ca2+-mediated crosslinking, intended to complement self-assembly and gelation of aqueous to-CNF in the adMSC cultivation medium, adversely affected both the mechanical properties of the hydrogel spheres and the growth of the encapsulated cells. However, cultivation under dynamic and hypoxic conditions significantly improved the proliferation and differentiation of the encapsulated adMSCs. Furthermore, we demonstrated that adMSCs in CNF hydrogel spheres exhibited potential for scalable EV production with potent immunosuppressive capacities in a bioreactor system. These findings underscore the importance of physiological culture conditions and the suitability of cellulosic materials for enhancing the therapeutic potential of MSCs. Overall, our study provides valuable insights for optimizing the in vitro cultivation of MSCs for various applications, including tissue engineering, drug testing, and EV-based therapies.

Background In this study we investigated in detail the role of cannabidiol (CBD), Beta-caryophyllene (BC), or their combinations in diabetic peripheral neuropathy (DN). The key factors that contribute to DN include mitochondrial dysfunction, inflammation, and oxidative stress. Methods Briefly, Streptozotocin (STZ) (55 mg/kg) was injected intraperitoneally to induce DN in Sprague Dawley rats and performed procedures including Randall Sellito Calipers, Von Frey Aesthesiometer, hot plate, and cold plate methods to determine mechanical and thermal hyperalgesia in vivo. The blood flow to the nerves was assessed by using the Laser Doppler device. Schwann cells were exposed to high glucose (HG) at a dose of 30 mM to induce hyperglycemia and DCFDA, JC1 & Mitosox staining were done to determine mitochondrial membrane potential, reactive oxygen species and mitochondrial superoxides in-vitro. The rats were administered i.p with BC (30mg/kg), CBD (15mg/kg), or combination while Schwann cells were treated with 3.65 µM CBD, 75 µM BC, or combination to assess their role in DN amelioration. Results Our results revealed that exposure to BC and CBD diminished HG-induced hyperglycemia in Schwann cells, in part, through reducing mitochondrial membrane potential, reactive oxygen species and mitochondrial superoxides. Further, BC and CBD combination treatment in-vivo could prevent the deterioration of mitochondrial quality control system by promoting autophagy and mitochondrial biogenesis while improving blood flow. CBD and BC treatments also reduced pain hypersensitivity to hyperalgesia and allodynia with increased antioxidant and anti-inflammatory action in diabetic rats. These in vivo effects were attributed to significant upregulation of AMPK, SIRT3, Nrf2, PINK1, PARKIN, LC3B, Beclin1 and TFAM functions while downregulation of NLRP3 inflammasome, NFκB, COX2 and p62 activity was noted as determined by western blotting. Conclusion the present studies demonstrated that STZ & HG induced oxidative and nitrosative stress play a crucial role in the pathogenesis of diabetic neuropathy. We find, for the first time, that CBD and BC combination ameliorate DN via modulating the mitochondrial quality control system.

During the recent pandemics of COVID-19, sequencing technics became powerful tool for gaining information about the SARS-CoV-2 virus and using this knowledge in our advantage. Thanks to this advantage, scientists over the world were able to search for emerging variations, watching the virus evolving in real time. Assembly of the virus genomes is crucial part of getting this kind of useful information. In our study, we sequenced 79 samples from nasopharyngeal swabs of COVID-19 patients. Positivity on disease was evaluated by qRT-PCR. By studying assembly success rate, we noticed, that Ct-value of qRT-PCR can predict success of genome assembly and SARS-CoV-2 lineage assignment. In this work we described the relationship between Ct-value and further steps of genome construction and its assignment to specific viral strain.

Cancer metastasis into the brain constitutes one of the most severe but not uncommon development of cancer growth. Several factors control how cancer types interact with the brain to establish metastasis These factors include system of migration, system of infiltration of the blood-brain barrier and the interaction with host cells (e.g., neurons, astrocytes) and the immune system fight against metastasis in the brain. Although, brain radiotherapy is the main treatment procedure carried out to treat, new therapies are emerging that constitute a glimpse of hope for increasing the diminutive life expectancy currently forecasted to cancer patients who are facing the prospectus of brain metastasis. However applying these therapeutic strategies has been has not been effective. Thus there is a need for better understanding of the metastasis process in order to suggest novel therapeutic targets. In this review, we follow the journey of various cancer cells from their primary location through the various process that they undergo including EMT, penetration of the ECM, intravasation, extravasation and infiltration of the blood brain barrier ending up with colonization and angiogenesis. In each phase, we focus on molecules that could potentially be drug target candidates.

Due to the deteriorating state of surface waters and the resulting reduction in their availability for the population, efforts have been undertaken to develop a biodegradable or compostable water filtration system capable of reducing the amount of harmful bacteria in this environment. The aim of this research was to develop nonwovens using the classic needle-punching method with commercially available polylactide (PLA) polymer, and subsequently, to select appropriate concentrations of modifiers to create systems with antibacterial properties. The resulting composites could potentially serve as filtration materials for the purification of surface waters. Nanoparticles such as zinc oxide, titanium dioxide, and silver were employed in this research. These compounds exhibit antibacterial properties and are insoluble in water. To confirm the bactericidal activity of the additives, biological tests were conducted, and the distribution of these additives on the structure of the filtration material was examined using scanning electron microscopy (SEM) equipped with an energy dispersive spectroscopy (EDS) detector.

To solve large scale linear equations involved in the Fast Multipole Boundary Element Method (FM-BEM) efficiently, an iterative method named the generalized minimal residual method (GMRES)(m)algorithm with Variable Restart Parameter (VRP-GMRES(m) algorithm) is proposed. By properly changing a variable restart parameter for the GMRES(m) algorithm, the iteration stagnation problem resulting from improper selection of the parameter is resolved efficiently. Based on the framework of the VRP-GMRES(m) algorithm and the relevant properties of generalized inverse matrix, the projection of the error vector r_m+1 on r_m is deduced. The result proves that the proposed algorithm is not only rapidly convergent but also highly accurate. Numerical experiments further show that the new algorithm can significantly improve the computational efficiency and accuracy. Its superiorities will be much more remarkable when it is used to solve larger scale problems. Therefore, it has extensive prospects in the FM-BEM field and other scientific and engineering computing.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

In Ultra-wideband (UWB)-based wireless ranging or distance measurement, differentiation between line-of-sight~(LOS), non-line-of-sight~(NLOS), and multi-path (MP) conditions are important for precise indoor localization. This is because the accuracy of the reported measured distance in UWB ranging systems is directly affected by the measurement conditions (LOS, NLOS or MP). However, the major contributions in literature only address the binary classification between LOS and NLOS in UWB ranging systems. The MP condition is usually ignored. In fact, the MP condition also has a significant impact on the ranging errors of the UWB compared to the direct LOS measurement results. Though, the magnitudes of the error contained in MP conditions are generally lower than completely blocked NLOS scenarios. This paper addresses machine learning techniques for identification of the mentioned three classes (LOS, NLOS, and MP) in the UWB indoor localization system using an experimental data-set. The data-set was collected in different conditions at different scenarios in indoor environments. Using the collected real measurement data, we compare three machine learning (ML) classifiers, i.e., support vector machine (SVM), random forest (RF) based on an ensemble learning method, and multilayer perceptron (MLP) based on a deep artificial neural network, in terms of their performance. The results show that applying ML methods in UWB ranging systems are effective in identification of the above-mentioned three classes. In specific, the overall accuracy reaches up to 91.9% in the best-case scenario and 72.9% in the worst-case scenario. Regarding the F1-score, it is 0.92 in the best-case and 0.69 in the worst-case scenario. For reproducible results and further exploration, we (will) provide the publicly accessible experimental research data discussed in this paper at PUB - Publications at Bielefeld University. The evaluations of the three classifiers are conducted using the open-source python machine learning library scikit-learn.

The move towards a new Circular Economy (CE) economic model has been advocated and supported in Portugal, however, there is limited research on this topic. To address this gap, a quantitative research based on an online survey was carried out among 99 Portuguese organizations, encompassing a wide range of sectors and sizes. The results show that CE is regarded as a strategic and relevant issue for profitability and value creation. Furthermore, the perception that it requires the adoption of new business models in addition to the classical “reduce, reuse, and recycle” approach is growing. Moreover, based on the hypotheses raised, results suggest that the level of CE adoption is positively impacted by the status of the EMS (Environmental Management System) certification and the willingness to improve the environmental performance and achieve a sustainable business model. However, CE activities are still relatively modest and a friendlier context (fiscal, legal, organizational, etc.) and the stronger support from supply chain agents and consumers are required. Future research should focus on how to design and shape the transition from a linear to a CE economy, and to ascertain if the positive attitude towards CE is materialized in changing the way business is done.

This paper is concerned about the novel exact solitons to the truncated M-fractional (1+1)-dimensional non-linear generalized Bretherton model with arbitrary constants . This model is used to explain the resonant nonlinear interaction between the waves in different phenomenon, including fluid dynamics, plasma physics, ocean waves, and many others. A series of exact solitons, including bright, dark, periodic, singular, singular-bright, singular-dark, and other solitons are obtained by applying the extended sinh-Gordon equation expansion (EShGEE), and the modified (G′/G2)-expansion tech- niques. A novel definition of Fractional derivative provides the solutions distinct from the present solutions. Mathematica software is used to obtain, and verify the solutions. The solutions are shown through 2-D, 3-D, and density plots. The stability process is performed to verify that the solutions are exact and accurate. The modulation instability is used to determine the steady-state stable results to the corresponding equation.

This study investigates the emergence of ertapenem-resistant, meropenem-susceptible (ErMs) among non-carbapenemase producing (NCP) and carbapenemase producing (CP) Escherichia coli and Klebsiella pneumoniae. As mutations for ertapenem resistance establish the genetic background for non-carbapenemase meropenem resistance, there is a great need for antibiotic stewards and researchers to understand the determinants of a strain’s propensity to become resistant. Whole genome sequencing was conducted on clinical carbapenem-resistant E. coli (CREC) and K. pneumoniae (CRKP) across 5 hospitals in San Antonio, U.S. from 2012-2018. The majority of carbapenem resistant Enterobacterales (CRE) were NCP (54%; 41/76). The blaCTX-M was found to be most prevalent among NCP isolates (p = 0.02). LC-MS/MS analysis of carbapenem hydrolysis revealed that blaCTX-M-mediated carbapenem hydrolysis, indicating the need to reappraise the term, “non-carbapenemase (NCP)” for quantitatively uncharacterized CRE strains harboring blaCTX-M. Antimicrobial susceptibility results showed that 56% of all NCPE isolates had an ErMs phenotype (NCPE vs. CPE, p &lt; 0.001), with E. coli driving the phenotype (E. coli vs. K. pneumoniae, p &lt; 0.001). ErMs strains carrying blaCTX-M, had approximately 4-fold more copies of blaCTX-M than ceftriaxone-resistant but ertapenem and meropenem susceptible (EsMs) isolates (3.7 v. 0.9, p &lt; 0.001). ErMs also carried more mobile genetic elements (MGEs), particularly IS26 composite transposons, than EsMs (37 vs. 0.2, p &lt; 0.0001). Immunoblot analysis demonstrated the absence of OmpC expression in NCP-ErMs E. coli, with 92% of strains lacking full contig coverage of ompC. Overall, this work provides evidence of a collaborative effort between blaCTX-M and OmpC in NCP strains that confer resistance to ertapenem but not meropenem. To thwart potential mismanagement of CRE infected patients, future efforts should focus on understanding the mechanism(s) underlying OmpC loss, developing rapid methods to detect blaCTX-M copy number variants, and targeted antimicrobials for NCPE and ErMs strains.

Background: Polycystic ovary syndrome (PCOS) is a common reproductive and endocrinological disease characterized by ovulatory dysfunction, polycystic ovaries, and hyperandrogenism. Adipokines are believed to contribute to developing PCOS and its accompanying metabolic complications such as dyslipidemia, insulin resistance, and cardiovascular diseases. Oncostatin M (OSM), a novel adipokine, plays a role in oogenesis, lipogenesis, and inflammation and may contribute to PCOS pathogenesis and its related metabolic problems. Methods: In this case-control study, the patients were grouped in a 1:1 ratio into either the PCOS (n = 32) or the control group (n = 32). Blood samples were obtained between the 3rd and 5th days of the menstrual cycle. Serum levels of fasting glucose, insulin, C-reactive protein (CRP), low-density lipoprotein, high-density lipoprotein, triglyceride, white blood cell count, thyroid-stimulating hormone, luteinizing hormone, follicle-stimulating hormone, total testosterone, prolactin estradiol, and OSM were analyzed. Results: OSM levels were significantly lower, but CRP levels were substantially higher in the PCOS group than in the control group (p = .002, p = .001, respectively). OSM was inversely correlated with total cholesterol, non-high-density lipoprotein cholesterol, fasting glucose, and the luteinizing hormone/follicle-stimulating hormone ratio (ρ = .329, p = .017; ρ = .386, p = .005; ρ = .440, p = .001; ρ = .316, p = .023, respectively). Conversely, there was no correlation between OSM and total testosterone level (ρ = .220; p = .118). In the context of inflammation and metabolic parameters, OSM was inversely correlated with CRP, Homeostatic Model Assessment for Insulin Resistance score (HOMA-IR), and low-density lipoprotein cholesterol (LDL) (ρ = .353, p = .019; ρ = .275, p = .048; ρ = .470, p &lt; .001, respectively). The performance of Oncostatin M for diagnosing PCOS showed 50% sensitivity, 75% specificity, and 63% accuracy (p = .009) in ROC curve analysis. Conclusions: Plasma OSM levels were considerably lower in patients with PCOS than in the control group, and this was inversely correlated with the hormonal and metabolic parameters of PCOS. Thus, OSM may be a novel therapeutic target for PCOS and metabolic complications.

In this paper, chaos sequence is used to replace the traditional Spread Spectrum sequence. From the perspective of the communication partner, a new method of generating the initial value of chaotic sequence is proposed, which is more suitable for the multi-base Spread Spectrum System and easy to extract. In order to further improve the error performance of the system and ensure the integrity of the system, an improved suboptimal soft information extraction method based on log-likelihood ratio (LLR) is proposed in the channel coding module, which can further improve the error performance of the system. On this basis, we choose the synchronization mode of multiple transmission of one reference signal to solve the problem that chaotic sequence is difficult to obtain synchronization because of its aperiodic characteristics. Finally, the system is simulated in the channel with low SNR. The simulation results show that chaotic sequence as Spread Spectrum code can make the signal transmit accurately in the worse channel environment. The performance gain of applying soft information decoding decision in the M-ary Spread Spectrum System with chaotic sequence as Spread Spectrum code can reach 5.2dB compared with the traditional Direct Spread Spectrum System.

Imbalance of homeostasis between the microbial communities and the host system leads to dysbiosis in oral micro flora. DMTU (1,3-di-m-tolyl-urea), is a biocompatible compound that was shown to inhibit Streptococcus mutansbiofilms by inhibiting its communication system (quorum sensing). Here, we hypothesized that DMTU is able to inhibit multispecies biofilms. We developed a multispecies oral biofilm model comprising an early colonizer Streptococcus gordonii, a bridge colonizer Fusobacterium nucleatum, and late colonizers Porphyromonas gingivalis, Aggregatibacter actinomycetemcomitans. We performed comprehensive investigations to demonstrate the effect of DMTU on planktonic cells and biofilms. Our findings showed that DMTU inhibits and disrupts multispecies biofilms without bactericidal effects. Mechanistic studies revealed significant down regulation of biofilm and virulence related genes in P. gingivalis. Taken together, our study highlights the potential of DMTU to inhibit polymicrobial biofilm communities and their virulence.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

There is a huge need to search for new treatment options and potential biomarkers of therapeutic response to antidepressant treatment. Depression and metabolic syndrome often coexist while pathophysiological overlap, including microbiota changes, may play a role. The aim of the study is to assess the effect of probiotic supplementation on symptoms of depression, anxiety and stress, metabolic parameters, inflammation and oxidative stress markers, and faecal microbiota in adult patients with depressive disorders depending on the co-occurance of MetS. The trial will be a four-arm, parallel group, prospective, randomized, double-blind, controlled design that will include 200 participants and will last 20 weeks. The probiotic preparation will contain Lactobacillus helveticus Rosell®-52, Bifidobacterium longum Rosell®-175. We will assess the level of depression, anxiety and stress, quality of life, blood pressure, body mass index and waist circumference, white blood cells count, serum levels of C-reactive protein, HDL cholesterol, triglicerides, fasting glucose, faecal microbiota composition and the level of some faecal microbiota metabolites, as well as inflammation markers and oxidative stress parameters in serum. The trial may establish a safe and easy-to-use treatment option as an adjunct in a subpopulation of depressive patients only partially responsive to pharmacologic treatment. (ClinicalTrials.gov identifier: ).

Hepatic vein outflow obstruction causes congestion of the liver, leading to necrosis, fibrosis, and portal hypertension (PH). Transjugular intrahepatic portosystemic shunt (TIPS) reduces congestion and PH by providing artificial outflow. The aim of the study was to investigate fibrosis progression in patients with Budd-Chiari syndrome (BCS) and TIPS using transient elastography (TE). From 2010 to 2022, 25 patients received 80 TEs using FibroScan® (3.2±2.1 per patient). TIPS function was assessed using Doppler ultrasound or radiological intervention. At the time of TE examination, 21 patients had patent shunts. Four patients had occluded shunts but normal pressure gradients during the intervention. The first TE measurement performed 9.8±6.8 years after the BCS diagnosis showed stiffness values of 24.6±11.5 kPa. A second or last measurement performed 7.0±2.9 years after the first measurement showed similar stiffness values of 24.1±15.7 kPa (p=0.943). Except for three patients, the liver stiffness was always >12 kPa, indicating advanced fibrosis. Stiffness values obtained <5 years (n=8, 23,8±9,2 kPa) or >5 years after the BCS diagnosis (24,9±12,7 kPa) did not differ (p=0.907). In addition, stiffness was not related to the interval between BCS and TIPS implantation (p=0.999). One patient received liver transplantation, and two patients died from non-hepatic causes. Most patients develop mild to moderate cirrhosis, possibly during the early phase of the disease. Timing of TIPS did not influence fibrosis progression. This and the release of portal hypertension may argue in favor of a generous TIPS implantation practice in patients with BCS.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.