The frequency synthesizer is a critical component in Cs beam clock technology. In this paper, we present a demonstration of a direct microwave frequency-synthesis chain for a cesium-beam atomic clock, which utilizes frequency multiplication and a dual-phase-locked loop mode. A detailed analysis of the frequency-synthesis chain is conducted, and a mathematical model is established. The phase settling time and system stability are simulated, measured, and verified. The experimental results for the phase settling time align with the simulation outcomes. The phase settling time can be adjusted within the range of 644.5 µs to 1.5 ms, and the absolute phase noise values are -63.7 dBc/Hz, -75.7 dBc/Hz, -107.1 dBc/Hz, and -122.5 dBc/Hz at 1 Hz, 10 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Additionally, the Ramsey fringes are detected, and the Allan deviations of the 10 MHz output from the cesium-beam atomic clock are measured to be 2.99×10−12 at 1s and 8.02×10−14 at 10,000 s.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

In Hawaiʻi, the transition from customary subsistence flooded taro agroecosystems, which regulate stream discharge rate trapping sediment and nutrients, to a plantation-style economy (c. the 1840s) led to nearshore sediment deposition - smothering coral reefs and destroying adjacent coastal fisheries and customary fishpond mariculture. To mitigate sediment transport, Rhizophora mangle was introduced in estuaries across Hawai’i (c. 1902) further altering fishpond ecosystems. Here, we examine the impact of cultural restoration between 2012-2018 at Heʻeia Fishpond, a 600-800-year-old walled fishpond. Fishpond water quality was assessed by calculating water exchange rates, residence times, salinity distribution, and abundance of microbial indicators prior to and after restoration. We hypothesized that R. mangle removal and concomitant reconstruction of sluice gates would increase mixing and decrease bacterial indicator abundance in the fishpond. We find that Heʻeia Fishpond’s physical environment is primarily tidally driven; wind forcing and river flux are secondary drivers. Post-restoration, two gates in the northeastern region account for >80% of relative flux in the fishpond. Increase in exchange rates during spring and neap tide and shorter minimum water residence time corresponded with the reconstruction of a partially obstructed 56 m gap together with the installation of an additional sluice gate in the fishpond wall. Lower mean salinities post-restoration suggests increased freshwater influx due to R. mangle removal. Spatial distribution of microbial bio-indicator species inversely correlated with salinity. Average abundance of Enterococcus and Bacteroidales did not significantly change after restoration efforts, however, average abundance of a biomarker specific to birds nesting in the mangroves decreased significantly after restoration. This study demonstrates the positive impact of biocultural restoration regimes on water flushing and water quality parameters, encouraging the prospect of revitalizing this and other culturally and economically significant sites for sustainable aquaculture in the future.

Though Cyber Physical Systems (CPS) become very popular in last the decade, dependability of CPS is still a critical issue and related survey is rare. We try to spell out the jigsaw of technologies and figure out the technical trends of dependable self-managing CPS. This survey first recalls the motivation and the similar concepts. By analyzing four generic architectures, we summarize the common characteristics and related assurance technologies, and propose a more generic environment-in-loop processing flow of CPS and a formal interaction flow between physical space and cyber space. Further, the similarity between correctness and dependability is formally analyzed and the new five research questions of dependable self-managing CPS are presented. Then we review the critical technologies and related correctness verification & validation (V&V) methods, the architectures for dependable self-managing CPS. Further, the detail dependability management and V&V technologies are surveyed, which covers the areas of running-time fault management methods and whole life cycle V&V technologies, maintenance and available tool sets. For holistic CPS development, Modeling techniques and MDE (model driven engineering) based V&V methods are analyzed in detail. Then we complete the jigsaw of technologies and figure out the missing part. Further, we propose the technical challenges and the further direction. To our best knowledge, this is the first comprehensive survey on dependable self-managing CPS development and evaluation.

Cyber Physical Systems (CPS) has been a popular research area in the last decade. The dependability of CPS is still a critical issue, and rare survey has been published in this domain. CPS is a dynamic complex system, which involves various multidisciplinary technologies. To avoid human error and to simplify management, self-management CPS (SCPS) is a wise choice. And to achieve dependable self-management, systematic solution is necessary to verify the design and to guarantee the safety of self-adaptation decision, as well as to maintain the health of SCPS. This survey first recalls the concepts of dependability, and proposes a generic environment-in-loop processing flow of self-management CPS, and then analyzes the error sources and challenges of self-management through the formal feedback flow. Focus on reducing the complexity, we first survey the self-adaptive architecture approaches and applied dependability means; then we introduce a hybrid multi-role self-adaptive architecture, and discuss the supporting technologies for dependable self-management at the architecture level. Focus on dependable environment-centered adaption, we investigate the verification and validation (V&V) methods for making safe self-adaptation decision and the solutions for processing decision dependably. For system-centered adaption, the comprehensive self-healing methods are summarized. Finally, we analyze the missing pieces of the technology puzzle and the future directions. In this survey, the technical trends for dependable CPS design and maintenance are discussed, an all-in-one solution is proposed to integrate these technologies and build a dependable organic SCPS. To the best of our knowledge, this is the first comprehensive survey on dependable SCPS building and evaluation.

Heterosis plays a significant role in enhancing variety, boosting yield, and raising economic value, but the molecular mechanism is still unclear. We analyzed the transcriptomes and 3D genomes of hybrid (F1) and its parents (w30 and 082). Analysis of the expression revealed a total of 485 specially expressed genes (SEGs), 173 differentially expressed genes (DEGs) above parental expression level, more actively expressed genes and up-regulated DEGs in F1. Further study revealed that the DEGs detected in F1 and its parents were mainly involved in response to auxin, plant hormone signal transduction, DNA metabolic process, Purine metabolism, starch and sucrose metabolism, which suggested that these biological processes may play a crucial role in the heterosis of B. rapa. The analysis of 3D genome data revealed that hybrid F1 tend to contain more transcriptionally active A compartments after hybridization. Additionally, F1 had a smaller TAD (topologically associated domain) genome length, but the number was the highest, and the expression change of activated TAD was higher than repressed TAD. More specific TAD boundaries were detected between parents and F1. Subsequently, 140 DEGs with genomic structural variants were selected as potential candidate genes. Among them, we found two DEGs with consistent expression changes in A/B compartments and TADs. Our findings suggest that genomic structural variants, such as TADs and A/B compartments, may affect gene expression and contribute to heterosis in B. rapa. This study provides further insight into the molecular mechanism of heterosis in B. rapa.

Multiple sclerosis is a chronic, autoimmune disease that mainly affects the central nervous system, including the brain, spinal cord, and optic nerve. This disease can cause clinical symptoms such as cognitive decline, muscle weakness, spasms, and fatigue in patients, and the onset tends to be younger. Current medication can only prevent or alleviate symptoms, so early diagnosis of this disease can increase patients' chances of treatment. Although the use of nuclear magnetic resonance detection can improve the efficiency of early auxiliary diagnosis, it still requires experienced doctors to spend too much time and energy on comprehensive judgment. To reduce the time cost and improve the efficiency of multiple sclerosis diagnosis, this article proposes a detection and recognition algorithm for multiple sclerosis based on wavelet entropy and self-adaptive particle swarm optimization. Firstly, a triple discrete wavelet transform is performed on the brain image of multiple sclerosis, and then 10 wavelet entropies are extracted from the decomposed wavelet subbands, which can reduce the feature dimensions of the image; Then, the algorithm of self-adaptive particle swarm optimization is used to optimize the feedforward neural network, in order to obtain the optimal connection weights and thresholds during the training process. The result of the model is with an average sensitivity of 92.29±1.89, specificity of 92.54±0.67, precision of 92.48±0.59, accuracy of 92.42±0.88, and F1 score of 84.85±1.74, Matthews correlation coefficient of 92.37±0.96, and Fowlkes223 Mallows Index of 92.38±0.96. The experimental results indicate that this algorithm has a very important data support role in detecting multiple sclerosis.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

Recent prolonged dry periods and lack of irrigation water have severely affected the productivity of coffee farms’ in the Central Highlands of Vietnam. This paper analyzes the efficiency of irrigation water use for Robusta coffee (Coffea canephora) in Lam Dong province, Highlands, Vietnam. A Cobb-Douglas production function was used to determine coffee productivity’s response to the application of irrigation water and other production factors using data collected from 194 farmers while the Technical Efficiency (TE) and Irrigation Water Use Efficiency (IWUE) were analyzed using a Data Envelopment Analysis (DEA) model. The correlation of different factors to IWUE was determined using the Tobit model. The production function analysis using Cobb-Douglas shows that the volume of irrigation water, amount of working capital, labor and farm size significantly influence coffee productivity. It also shows that indigenous farmers are more efficient in utilizing irrigation water than the (mostly Kinh) migrant farmers. The Tobit result, on the other hand. indicates that farmers’ experience, education level, distance of farm to water source, security of access to water source, extension contact and credit access significantly affect IWUE. The study findings further suggest that mitigating water shortages in coffee farms require sub-regional and national policy support such as better access to credit and extension services, training, land management and household-level effort to improve farming practices, through the application of appropriate technologies and traditional knowledge.

Ecological stoichiometry is an important index to reflect ecological interaction and the balance of various elements in ecological processes. At present, the stoichiometric spatial distribution of soil carbon (C), nitrogen (N), phosphorus (P) and potassium (K) in farmland and grassland of Inner Mongolia and its influencing factors are still unclear. In this study, the spatial distribution of soil nutrient content and stoichiometry and the effects of environmental factors on soil C:N:P:K stoichiometry were analyzed under different land use patterns in four agro-pastoral areas. The results showed that there was a geographical gradient in the ecological stoichiometric relationship between farmland and grassland. RCN, RCP, RCK, RNP and RNK showed an "N" distribution from west to east, while RPK showed a "V" distribution. The difference in spatial distribution was more significant than the difference in land use pattern. The ecological stoichiometric relationship of grassland was mainly affected by the content of C and N, and was related to the similarity of soil properties. The field ecological stoichiometry was mainly affected by the content of nitrogen and phosphorus, and had a great relationship with fertilization. The effects of MAT and MAP on soil ecological stoichiometry were related to the inter-regional environmental heterogeneity. The influence of MAP on farmland and MAT on grassland was more significant. It was of great significance for field management according to local conditions, rational utilization of land resources and sustainable development of agriculture to clarify the ecological stoichiometric characteristics of farmland and grassland in agro-pastoral ecotone.

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

On 17 October 1947, Niels Bohr was made a knight of the Order of the Elephant by the King of Denmark in view of his outstanding achievements and contributions to science. Bohr designed his own coat of arms that featured a pattern of Yin and Yang (Tai Chi symbol) to symbolize the wave-particle complementarity. However, Bohr’s Yin-Yang diagram (YYD) was neither drawn based on the principles of quantum mechanics, nor did it originate from the traditional Taoist YYD. Scientists still have doubts about the legitimacy of using YYD as the icon of the wave-particle complementarity, because the YYD belonging to quantum mechanics itself is unknown so far. This article reports the YYDs existing in quantum mechanics and justifies the role of YYD in the wave-particle duality by showing that any system, whether classical or quantum, has an ideal YYD as long as it satisfies Bohr’s principle of complementarity (BPC). The deviation of a deformed YYD from the ideal YYD indicates the extent to which a real system satisfies BPC. This article constructs the quantum YYD by the complex quantum trajectory of a particle tunneling via a step barrier, which displays the continuous transition between the wave behavior and the particle behavior. It appears that the YYD designed by Bohr in his coat of arms resembles the YYD generated by tunneling motion, not only in appearance but also in the governing equation.

Plant height is one of the key agronomic traits for improving the yield of sweetpotato. The phytohormones, especially gibberellins (GAs) are crucial to regulate plant height. The 9-cis-epoxycarotenoid dioxygenase (NCED) is the key enzyme for abscisic acid (ABA) biosynthesis signalling in higher plants. However, its role in regulating plant height has not been reported to date. Here, we cloned a NCED gene, IbNCED1, from sweetpotato cultivar Jishu26. This gene encoded the 587-amino acid polypeptide containing an NCED superfamily domain. The expression level of IbNCED1 was highest in the old tissues in the field-grown Jishu26. The expression of IbNCED1 was induced by ABA and GA. Overexpression of IbNCED1 promoted the accumulation of ABA and inhibited the content of active GA3 and plant height, and affected the expression levels of genes involved in the GA metabolic pathway. IbNCED1 overexpression reduced sensitivity to GA3 and exogenous application of GA3 could rescue the dwarf phenotype. In conclusion, we suggest that IbNCED1 regulates plant height and development by controlling the accumulation of active GA3 signalling pathway in transgenic sweetpotato.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

(1) Background : When placing implants in the maxillary posterior region with insufficient alveolar bone, a maxillary sinus elevation is necessary. Autogenous bone, though biologically ideal, poses risks and discomfort due to donor site harvesting. Block-type autogenous tooth bone graft material, made from the patient’s own extracted tooth, offers similar biological stability without these drawbacks; (2) Methods : This study observed the progress of 19 implant patients who were treated with maxillary sinus elevation procedures using block-type autogenous tooth bone graft material at the Daegu Catholic University Medical Center. Extracted teeth were processed into demineralized tooth block bone. After elevating the sinus membrane, implants and the tooth bone graft material were placed in the space, and the bony window was repositioned. Postoperative evaluations through clinical observation and radiographic imaging assessed sinus membrane elevation, alveolar bone height increase, and implant osseointegration; (3) Results : Results showed proportional increases in alveolar bone height to the graft material size, with long-term stability. No postoperative complications occurred, even with sinus membrane perforation, and implants remained stable; (4) Conclusions : The study concludes that maxillary sinus lifts using block-type autogenous tooth bone graft material provide excellent bone induction and biocompatibility, making it a highly beneficial method for both dentists and patients.

The Range–Doppler (R-D) model is extensively employed for the geometric processing of Synthetic Aperture Radar (SAR) images. Refining the sensor motion state and imaging parameters is the most common method for achieving high-precision geometric processing using the R-D model, comprising a process that involves numerous parameters and complex computations. In this study, we introduce a novel approach to improve the positioning accuracy of the R-D model, implementing a low-order polynomial to compensate for the original imaging errors without altering the initial positioning parameters. We also design low-order polynomial compensation models with different parameters. The models are evaluated on various SAR images from different platforms and bands, including spaceborne TerraSAR-X and GF3-C images, manned airborne SAR-X images, and unmanned aerial vehicle-mounted miniSAR-Ku images. Furthermore, image positioning experiments involving the use of different polynomial compensation models and various numbers and distributions of Ground Control Points (GCPs) are conducted. The experimental results demonstrate that geometric processing accuracy comparable to that of the classical rigorous positioning method can be achieved even when applying only an affine transformation model to the images. Compared to classical refinement models, however, the proposed image-compensated R-D model is much simpler and easy to implement. Thus, this study provides a convenient, robust, and widely applicable method for the geometric positioning processing of SAR images, offering a potential approach for the joint-positioning processing of multi-source SAR images.

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

In-depth insights into the profound impacts of climate change and human activities on water resources are garnered through the dynamic changes in surface water, a crucial aspect of effective water resource management and the preservation of aquatic ecosystems. This paper introduces an innovative approach employing the random forest algorithm for the systematic extraction and monitoring of surface water at large regional or national scales. This method integrates spectral bands, spectral indices, and digital elevation model data, offering a novel perspective on this critical task. A data filling model is proposed to mitigate the impact of missing data due to cloud cover. Leveraging the capabilities of the Google Earth Engine (GEE), detailed information on surface water dynamics during the rainy and dry seasons in the Yangtze River Basin (YRB) from 1991 to 2021 is extracted using Landsat time series imagery. The analysis encompasses spatial-temporal variation characteristics and trends, with a specific focus on the intricate interplay between the areal extent of surface water and hydro-meteorological factors in each sub-basin of the YRB. Importantly, this includes considerations of potential groundwater contributions to surface water. Key findings from our research include: (1) Achieving a remarkable overall accuracy of 0.96 ± 0.03 in obtaining reliable surface water datasets with the support of GEE. (2) Identifying significant trends, such as a noteworthy increase in rainy season surface water bodies (+248.0 km2·yr−1) and a concerning decrease in surface ice/snow cover during both rainy and dry seasons, with change rates of −39.7 km2·yr−1 and −651.3 km2·yr−1, respectively. (3) Uncovering the driving mechanisms behind these changes, revealing positive correlations between the areal extent of rainy season surface water bodies and precipitation, as well as negative correlations between surface ice/snow cover area and average surface skin temperature. It is crucial to note that these driving factors exhibit variation among secondary river systems, underscoring the complexity of surface water dynamics. Furthermore, comparative analyses with existing surface water products are conducted, contributing to a deeper understanding of the advantages and uncertainties inherent in our proposed extraction method. The proposed method for large-scale surface water extraction not only enhances the monitoring of spatio-temporal surface water dynamics in the YRB but also provides valuable insights for the sustainable utilization and protection of water resources, considering the potential role of groundwater in supplementing surface water.

In recent years, due to the low energy utilization of the whole life-cycle of buildings and the di-minished indoor and outdoor comfort of buildings and the impact on the surrounding environ-ment caused by the carbon emissions of the building life-cycle, the establishment of a whole life- cycle carbon emission model for buildings to improve their energy utilization at all stages of their life-cycle has received unprecedented attention. In China, the construction industry has become a major carbon emitter, and traditional houses, as a green development building type, are an effec-tive way to achieve carbon neutrality in buildings, but the existing green building evaluation system lacks quantitative indicators of carbon emissions in the building life-cycle. The exclusive evaluation indexes for regional and characteristic buildings, such as traditional houses, are ne-glected; This study explored the formula for calculating the life-cycle carbon emissions model of traditional residential houses under a carbon emission intervention and used real measurements of the physical environment and comparative analysis of the limitations of existing local stand-ards; The results showed that the carbon emission calculation formulas for each stage of the life-cycle of traditional residential houses must be established by combining the selection of local building materials, and the materials for sustainable energy and carbon sinks of green systems. Based on the results of indoor and outdoor heat and humidity environmental tests of residential houses and an analysis of the limitations of existing evaluation indexes due to locality, four im-portant factors affecting locality green buildings in terms of energy utilization, site ecology and landscape, land saving and material saving were extracted; on this basis, the whole life-cycle carbon emission model of traditional residential houses is constructed by combining the existing green building evaluation standards with the carbon emission indexes of the life-cycle of tradi-tional residential houses.

Ecological ternary cements (ECP) were perpared with powders of phosphogypsum (PG), fly ash (FA) and portland cement (PC). The evolution mechanism of the hydration product structure was characterized through macro and micro experiments.The thermodynamic characteristics of solid phase, solid solution phase and aqueous solution in process of hydration about phosphogypsum-fly ash-cement ternary cementitious system were studied based on the Gibbs-free-energy C-S-H thermodynamic model and GEM-Selektor software, and compared with experimental results. The results show that in the hydration reaction the thermodynamic interaction between mineral single-phase and hydration products plays an important role in the spatio-temporal distribution of ions in the cementitious system. The values of CaO、SiO2Hand H2Ohyd gradually increased with the increase of Ca/Si ratio, while the values of CaOext and H2OOH showed a positive proportional relationship, and the values of SiO2H and SiO2 showed an inverse proportional relationship. GEM-Selektor is accurate in the simulation calculation of the total amount of AFt and AFm mineral phases which quantitatively analysis the correlation between C-S-H gels formation and C3S with complex decomposition ion groups.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

Arabidopsis contains eight different h-type thioredoxins (Trx) being distributed in different cell organelles. Although Trx h2 is deemed to be localized in mitochondria, its subcellular localization and function remains a matter of debate. Here, Trx h2 localization and function were investigated using cell fractionation studies and reverse genetics. Differential centrifugation and immunodetection showed the Trx h2 protein to be distributed to the microsomal fraction rather than to mitochondrial preparations. To analyze whether Trx h2 has different roles than mitochondrial Trxs, Arabidopsis mutants lacking Trx h2 were compared with mutants deficient in mitochondrial Trx o1 and double mutants with joint deficiencies in both Trxs. Under constant medium light, trxh2 grew as the wild type, while trxo1 and trxo1h2 mutants showed impaired growth. This was accompanied by differences in the metabolite profiles. The trxo1 and trxo1h2 mutants clustered differently from the wild type during the night, revealing a decrease in ascorbate and glutathione redox states. In fluctuating light intensities, genotypic differences in growth rates were attenuated. Compared to the wild type, the fluctuating-light induced decrease in the NADPH/NADP ratio was diminished in the mutants, with the trxo1h2 double mutant showing the strongest effect. This was accompanied by an increase in the photosynthetic efficiency of the trxo1h2 mutant, specifically in the high light phases of fluctuating light. Conclusively, these results support the view that Trxs o1 and h2 are localized in different subcellular compartments, and have different effects on ascorbate and glutathione redox states and growth in medium light, but cooperatively affect NADP(H) redox state and photosynthetic efficiency in fluctuating light.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

The sample data are used from Shaanxi Statistical Yearbook （1999-2018）and poverty population in X County of Southern Shaanxi in 2018. By using Eviews and Excel, this report focuses on analyzing the relationship between education investment and economic growth, education for poverty population, per capita income and poverty caused by education in X county, which can explain reasons for the phenomenon of poverty caused by education. The countermeasures are proposed to solve the phenomenon of poverty caused by education, including establishing scientific education view, correctly understanding education investment and benefit, and improving the aid mechanism for poor students to realize the effective connect among poverty alleviation through education, accurate poverty alleviation and rural revitalization.

It is of merit to study the appropriate amount of fiber to add to free-range chickens feed to improve the microbial diversity and gut health in times of plant fiber deprivation. OptiCell is a useful source of fiber as a type of eubiotic lignocellulose, and its positive effects on the growth performance and laying performance of chickens has already been proven. However, few researchers have researched the effects of adding OptiCell on the gut microbiota of chickens. In this research we added three different levels of OptiCell (0%, 2% and 4%) to the feed of caged and free-range Bian chickens from September to November, aiming to observe the effects of adding OptiCell and different feeding modes on the gut microbial diversity and gut health of chickens, and aiming to determine an appropriate amount of OptiCell. The results showed that adding OptiCell could increase the thickness of the cecum mucus layer and the abundance of Akkermansia and Faecalibacterium in caged chickens, and 4% OptiCell was optimum. In addition, adding OptiCell increased the microbial diversity and the abundance of the butyrate-producing bacteria Faecalibacterium and Roseburia of fee-range chickens. The α-diversity and the length of the small intestine with 2% OptiCell in free-range chickens were better than with 2% OptiCell in caged chickens. In addition, compared with caged chickens, the free-range chickens had longer small intestine and lower GLP-1. Taken together, an appropriate amount of OptiCell benefitted the microbial diversity and health of chickens; it was necessary to add dietary fiber to the feed of free-range chickens when plant fibers was lacking, and 2% OptiCell was found to be optimum.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

Comprehensively understanding the spatial ecology and habitat preferences of endangered species is essential for population restoration and conservation. We investigated the home range and movement of the endangered Amur soft-shell turtle (Pelodiscus maackii) in the Ussuri River, Heilongjiang Province, Northeastern China. The study involved tracking 19 Amur soft-shell turtles from late June to mid-October, 2022, resulting in complete and partial home range size data for eight subadults and two adults, respectively. The primary analysis focused on eight subadults, and the models that best described daily movement were identified. We also explored the potential factors influencing home range size. Mean movement rate ranged from 39.18 ± 20.04 m to 72.45 ± 29.36 m and was positively correlated with the linear home range and water temperature. The most insightful home range estimate was a 95% kernel density estimate, employing likelihood cross-validation smoothing with constraints set to the river boundaries. The mean home range size was 1.02 ha and was not correlated with body size. Subadults tended to establish well-defined home ranges over time; whereas, defining home ranges for adults proved challenging. This research addresses a gap regarding the ecology of the Amur soft-shell turtle and provides a foundation for future conservation plans.

Val-Phe-Val-Arg-Asn (VFVRN) has been identified and screened from lipid-lowering chickpea peptides (ChPs) by using a pharmacokinetic model in our previous experiment. The present study was conducted to investigate its effects and mechanisms on lipid metabolism. A high-fat diet C57BL/6J mice model and 3T3-L1 preadipocyte cell model were used. VFVRN was found to significantly decrease the levels of some blood lipids. The expressions of LDL receptor (LDLR), peroxisome proliferator-activated receptors (PPAR)α, liver X receptor (LXR)α, cholesterol 7α-hydroxylase (CYP7A1) and AMP-activated protein kinase (p-AMPK) in liver were up-regulated by VFVRN treatment. The expressions of 3-hydroxy-3-methylglutaryl-coenzyme A reductase (HMGR), fatty acid synthetase (FAS), 1-aminocyclopropane-1-carboxylate synthetase (ACC), sterol regulatory element-binding protein (SREBP)-1c and SREBP-2 in liver were significantly (P<0.05) down-regulated. Additionally, the expressions of PPARα and PPARγ in adipose tissues were up-regulated by VFVRN significantly (P<0.05). VFVRN might also contribute to transintestinal cholesterol efflux (TICE) by up-regulating the expressions of LXRα and ATP binding cassette G5/8 transporters (ABGC5/8). Moreover, VFVRN promoted 3T3-L1 preadipocyte apoptosis by up-regulating the expressions of BaX, cleaved Caspase-3 and down-regulating Bcl-2. VFVRN had potent effects in reversing metabolic disorders of blood and liver in a high-fat diet mice model, as well as to promote the apoptosis of 3T3-L1 preadipocytes.

Increasing numbers of researchers are interested in the importance of dietary fiber for the gut microbiota, microbiotal metabolite SCFA, energy metabolism and gut health of the host. However, studies have demonstrated that long-term and longitudinal observation may be needed to evaluate the effect of dietary fiber better, and few such works have been made in chickens. Therefore, we successively fed low-fiber, high--fiber and low-fiber diets to two breeds of chickens during different growth periods (1—8, 9—20 and 21—50 weeks), aiming to longitudinally observe the long-term effect of altered dietary fiber on the gut microbiota, SCFA and development of cecum of chickens with age. The results showed that the composition and function of the gut microbiota, SCFA and the development of the cecum were different during different periods, which was largly affected by dietary fiber. However, the causes of some effects were different during the different periods. For example, compared with that in low-fiber chickens at 8 weeks, dominant fiber-degradation bacteria such as Bacteroidetes, Alloprevotella and SCFA-producing bacteria such as Faecalibacterium increased due to a high-fiber diet at 20 weeks, while due to a high feed intake in 50 weeks. Moreover, the concentration of SCFA in 20 weeks was significantly higher than in 8 weeks and 50 weeks, but the causes of this difference were also distinct. It was proposed that a long-term observation was needed to evaluate the effect of dietary fiber better on chickens. The metabolite pathways of ATP-binding cassette (ABC) transporters encoded by Firmicutes were enriched in 8 weeks, while a two-component system and β–glucosidase encoded by Bacteroidetes were enriched in 20 and 50 weeks. The trend was the same in two breeds of chickens except for Alloprevotella. In addition, the total content of SCFA in the contents of cecum was also affected by the size of the cecum. Surprisingly, the length of the cecum shortened from 20—50 weeks, maybe due to reduced dietary fiber.

Managing epidemics need to unite each individual of the nations. Lockdown is an essential strategy to fatal and threatening epidemic. All of the citizens should realize that each of people has a responsibility to support the public health crisis. How to organize individual to fight against the epidemic plaque depends each of them. This essay discussed the COVID-19 pandemic relevant self-governance of community from a historical perspective in China. Self-governance of neighborhood committee and community residential office in urban and rural helped to control the COVID-19 pandemic in the communities in China. Co-operation and collective responsibility of citizens and community support is a critical condition to prevent epidemic. The community self-governance can track back Qin Dynasty in China history. It established baojia system to maintain social control for thousand years. Now, the community-based system, baojia system is becoming more autonomous for local citizenship and socialized governance in China. We reviewed a historical pneumonia plaque in North China in 1911. Chinese doctor, Wu Lien-teh (伍連德) confronted the epidemic crisis with many measures such as lockdown, quarantine, the wearing of mask, setup mobile hospitals, travel restriction, the cremation of victims, and border control. Dr. Wu made effort to establish the modern public health service in China. We think that the combination of culture background of China community with modern public healthcare system determinedly played important role to control the COVID-19 pandemic.

A systematic investigation of the dynamic clustering behavior of active particles under confinement, including the effects of both particle density and active driving force is presented based on a hybrid coarse-grained molecular dynamics simulation. First, a series of scaling laws were derived with power relationships for the dynamic clustering time as a function of both particle density and active driving force. Notably, the average number of clusters N ̅ assembled from active particles in the simulation system exhibits a scaling relationship with clustering time t described by N ̅∝t^(-m). Simultaneously, the scaling behavior of the average cluster size S ̅ is characterized by S ̅∝t^m. Our findings reveals the presence of up to four distinct dynamic regions concerning clustering over time, with transitions contingent upon the particle density within the system. Furthermore, as the active driving force increases, the aggregation behavior also accelerates, while an increase in density of active particles induce alterations in the dynamic procession of the system.

The inhibition of alpha-glucosidase and alpha-amylase is one of clinic strategies for remedy the type II diabetes. Herbal medicines are reported to alleviate hyperglycemia. However, the constituents from those sources whether are targeted to the alpha-glucosidase and alpha-amylase still unexplored. This study attempted to select the compounds for efficacy of hypoglycemia via cellular and mouse levels. The results illustrated that the cytotoxicity in all tested compounds at various concentrations except the concentration of 16-hydroxy-cleroda-3,13-dine-16,15-olide (HCD) at 30 µM were not significant difference (p > 0.05) when compared with the untreated control. Acarbose (reference drug), Antroquinonol, Catechin, Quercetin, Actinodaphnine, Curcumin, HCD, Docosanol, Tetracosanol, Berberine, and Rutin could effectively inhibit the alpha-glucosidase activity of Caco-2 cells when compared with the control (maltose). The compounds (Curcumin, HCD, Tetracosanol, Antroquinonol, Berberine, Catechin, Actinodaphnine, and Rutin) could reduce blood sugar level at 30 min in tested mice. The effects of tested compounds on area under curve (AUC) were significant (p < 0.05) among Acarbose, Tetracosanol, Antroquinonol, Catechin, Actinodaphnine, and Rutin along with Berberine and Quercetin. In in vitro (alpha-glucosidase) with in vivo (alpha-amylase) experiments suggest that bioactive compounds can be a potential inhibitor candidate of alpha-glucosidase and alpha-amylase for the alleviation of type II diabetes.

This paper shows that the empirical distribution of cross-sectional analyst coverage in China's stock markets follows an exponential law in a given month from 2011 to 2020. The findings hold in both the emerging (Shanghai) and the developed market (Hong Kong). Moreover, the unique distribution parameter (i.e., mean) is directly related to the amount of market-wide information. Average analyst coverage exhibits a significant negative predictive power for stock-market uncertainty, highlighting the role of security analysts in diminishing the total uncertainty. The exponential law can be derived from the maximum entropy principle (MEP). When analysts, who are constrained by average ability in generating information (i.e., the first-order moment), strive to maximize the amount of market-wide information, this objective yields the exponential distribution. Contrary to the conventional wisdom that security analysts specialize in the generation of firm-specific information, empirical findings suggest that analysts primarily produce market-wide information for 25 countries. Nevertheless, it remains unclear why cross-sectional analyst coverage reflects market-wide information, this paper provides an entropy-based explanation.

Environmental responsibility and economic benefits have promoted the development of closed-loop supply chain (CLSC), and shortages and channels are considered to be two important issues in CLSC. This paper explores ordering and channel decisions in CLSC with new and differentiated remanufactured products, and considers the price and sales effort-dependent demands, as well as the proportion of emergency orders determined by emergency order costs and backorder losses, and establishes an integrated and decentralized CLSC game models. We introduce a stochastic sales effort, which affects two types of products. Numerical results show that sales effort and the order quantity of new and remanufactured products exhibit concave and convex functions, respectively. Wherein, the upper limit of sales effort has a greater impact on supply chain decisions. High sales efforts can serve as a means of coordinating dispersed supply chains. Moreover, in different cases, decisions of integrated channel are better than those of decentralized channel. Finally, whether the supply chain adopts an emergency order strategy depends on the relative cost of emergency orders and out of stock costs. According to the research in this article, some management insights are also provided.

Virus-infected Flu is a common disease. To date, no specific drugs are available to manage the symptoms of cough, headache and sputum production. An alternative Chinese herb medicine is introduced for virus-infected Flu or similar infection. Before hospitalization, some of patients may scare for cross-infection with mild symptoms or hardly go to hospital if encountered a temporary lockdown or quarantine. Some Chinese practice self-treatment of cough, headache and sputum production by inhalation of volatile chemicals from onion and garlic. Author used to take the same alternative approach of inhalation of onion, garlic or scallions for self-treatment when suffered virus caused flu with cough, headache and sputum production at onset disease. In this article, the biomedical effects of onion and garlic are reviewed. To help patients with mild symptoms of virus infected Flu, a simple home-based treatment was suggested to self-treatment because of temporary isolation and hardly going to hospitalization. The alternative approach may also suggest for some mild virus infected respiratory diseases caused by virus at onset disease.

We still do not have satisfactory answers about the inflationary and accelerating expansions of the universe, the missing mass problem, and the origins of the four fundamental forces and the quantum phenomena. Here, we introduce a new model of matter and space and a postulate on a constant of motion, and then show that an equation of motion derived from the constant of motion could provide new understandings of the above problems. For example, we show that there is a natural inflation scenario and that the co-moving distance to the closest accelerating supernova is clearly given as $c/(\sqrt{3} H)$ ($\sim$8.1 billion ly). In addition, we show that, in a system including a proton and an electron, the equation of motion has eight acceleration terms, some of which are suspected to be responsible for the four fundamental forces and the galaxy rotation anomaly. From further discussion, we conjecture that in order to understand the gravitational and strong interactions and the quantum phenomena, it is necessary to consider the expansion of the universe. The lensing mass distribution is explained, based on another postulate on a method of representing superposition.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

The nonlinear dynamics exhibited by aircraft flying at high angle of attack (AOA) pose great challenges to the design of flight control. The control design based on nonlinear dynamic inversion (NDI) is to reversely find the required control input based on the current nonlinear dynamics of the aircraft and the control objectives to be achieved. Since it is derived from the nonlinear dynamics of the aircraft, a single NDI controller can cover the entire flight envelope without the need for controller switching or gain scheduling. This paper employs the layered structure of the flight control loop to implement the NDI controller through the combination of aerodynamic control and thrust vectoring control (TVC). The resulting NDI controller is applied to an experimental F-16 installed with TVC to verify its high AOA maneuverability in the post-stall region. The verification simulation shows that the experimental F-16 under the NDI control can effectively track the high AOA command and successfully demonstrate the Herbst maneuver by performing the heading reversal with 70° AOA.

Functional connectivity (FC) is a potential candidate that can increase the performance of brain-computer interfaces (BCIs) in the elderly because of its compensatory role in neural circuits. However, it is difficult to decode FC by current machine learning techniques because of a lack of its physiological understanding. To investigate the suitability of FC in BCI for the elderly, we propose the decoding of lower- and higher-order FCs using a convolutional neural network (CNN) in six cognitive-motor tasks. The layer-wise relevance propagation (LRP) method describes how age-related changes in FCs impact BCI applications for the elderly compared to younger adults. Seventeen younger (24.5±2.7 years) and twelve older (72.5±3.2 years) adults were recruited to perform tasks related to hand-force control with or without mental calculation. CNN yielded a six-class classification accuracy of 75.3% in the elderly, exceeding the 70.7% accuracy for the younger adults. In the elderly, the proposed method increases the classification accuracy by 88.3% compared to the filter-bank common spatial pattern (FBCSP). LRP results revealed that both lower- and higher-order FCs were dominantly overactivated in the prefrontal lobe depending on task type. These findings suggest a promising application of multi-order FC with deep learning on BCI systems for the elderly.

Tsallis entropy has been widely used in image thresholding because of its non-extensive properties. The non-extensive parameter q contained in this entropy plays an important role in various adaptive algorithms and has been successfully applied in bi-level image thresholding. In this paper, the relationships between parameter q and pixels’ long-range correlations have been further studied within multi-threshold image segmentation. It is found that the pixels’ correlations are remarkable and stable for images generated by a known physical principle, such as infrared images and medical CT images. And the corresponding non-extensive parameter q can be evaluated by using self-adaptive Tsallis entropy algorithm. The results of this algorithm are compared with those of Shannon entropy algorithm and the original Tsallis entropy algorithm, in terms of quantitative image quality evaluation metrics PSNR (Peak Signal-to-Noise Ratio) and SSIM (Structural Similarity). Furthermore, we observed that for image series with the same background, the q values determined by the adaptive algorithm are consistently kept in a narrow range. Therefore, similar or identical scenes during imaging would produce similar strength of long-range correlations, which provides potential applications for unsupervised image processing.

Neuronal lesion or injury is a traditional approach to investigate neural circuit. Is any new neural pathway or new neurodegeneration related central nerve system injury? Spinal disc herniation can cause the spinal cord injury. However, the histological examination is still lack. It happened that a case of spinal disc herniation of a 10-year old dog was examined with NADPH diaphorase (N-d) histology. We did not find the N-d neurodegenerative aberrant in the tissue of the mid-rostral lumber segment besides the metamorphoses by the compression of the disc herniation. However, the severe neuropathological changes majorly occurred in the lumbosacral spinal cord. We found more diverse neurodegenerative alterations: the aging-related N-d body (ANB), megaloneurite and N-d homogeneous formazan globule in the lumbosacral spinal cord. We also found that a new circuit pathway (intermedial collateral pathway) showed by a megaloneurite between the lateral collateral pathway and the medial collateral pathway. The enormous notch caused by spinal disc herniation located at the mid-rostral lumber segments. The aging-related neurodegeneration occurred the specific lumbosacral segments. The homogeneous formazan globule was round or oval homogeneous N-d positivity which distributed in the gray matter and dorsal column. In the medulla oblongata, ANBs were revealed in the gracile nucleus, nucleus reticularis lateralis (ventrolateral spinal trigeminal nucleus) and middle of the spinal trigeminal nucleus.

Street view images can help us better understand the city environment and potential characteristics. With the development of computer vision and deep learning, the technology of semantic segmentation algorithms has become more mature. However, DeeplabV3+, which is commonly used in semantic segmentation, has shortcomings such as a large number of parameters, high requirements for computing resources, and easy loss of detailed information. Therefore, this paper proposes LM-DeeplabV3+, which aims to greatly reduce parameters and computations of the model while ensuring the segmentation accuracy. Firstly, the lightweight network MobileNetV2 is selected as the backbone network, and the ECA attention mechanism is introduced after MobileNetV2 extracts shallow features to improve the ability of feature representation; secondly, the ASPP module is improved, and on its basis, the EPSA attention mechanism is introduced to achieve cross-dimensional channel attention and important feature interaction; thirdly, a loss function named CL loss is designed to balance the training offset of multiple categories and better indicate the segmentation quality. This paper conducted experimental verification on the Cityspaces dataset, and the results showed that the mIoU reached 74.9%, which was an improvement of 3.56% compared to DeeplabV3+; the mPA reached 83.01%, which was an improvement of 2.53% compared to DeeplabV3+.

Object detection is important in many applications, such as autonomous driving. While 2D images are lack of depth information and are sensitive to environmental conditions, 3D point cloud can provide accurate depth information and a more descriptive environment. However, sparsity is always a challenge in single-frame point cloud object detection. This paper introduces a two-stage proposal-based feature fusion method for object detection using multiple frames. The proposed method, called proposal features fusion (PFF), utilizes a cosine-similarity approach to associate proposals from multiple frames and employs an attention weighted fusion module to merge features from these proposals. It allows for feature fusion specific to individual objects and offers lower computational complexity while achieving higher precision. The experimental results on the nuScenes dataset demonstrate the effectiveness of our approach, achieving a mAP of 46.7%, which is 1.3% higher than the state-of-the-art 3D object detection method.

The shear factor of ore drawing is one of the important factors affecting the formation of underground debris flow, and it has an important contribution to the formation of underground debris flow. The purpose of this paper is to study the effect of mining shear factor on underground debris flow in natural caving method. Based on the research background of the underground debris flow in Plan copper mine, this paper analyzes the characteristics of the slurry material structure of the underground debris flow, the influence of drawing shear factor on formation mechanism of underground debris flow is analyzed. The results show that the slurry of the underground debris flow in Plan mine is not only a pseudoplastic fluid but also a thixotropic fluid. It is indicated that once there is shearing force in drawing, it will deform, and its viscosity will decrease with the increase of shear rate and time. It is considered that the shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of ore drawing, it is reduced in viscosity and increased in fluidity, so that its “Activation” and then become a flowable paste, along with the bulk ore flow through the mouth. The continuous ore drawing process will continuously shear the new moraine slurry in the ore drawing channel and continuously “Activate” the moraine slurry in the ore drawing channel, finally, a certain scale and destructive down-hole debris flow accident. This paper is the first to study the effect of ore drawing shear factor on the formation mechanism of underground debris flow. It not only broadens the research field of debris flow, but also fills up the deficiency of systematic research on underground debris flow, and provides theoretical guidance for the prevention and control of underground debris flow.

The Simplified Spherical Harmonic (SPN) approximation was first introduced as a three-dimensional (3-D) extension of the plane-geometry Spherical Harmonic (PN) equations. A third order SPN (SP3) solver, recently implemented in the Nodal Expansion Method (NEM), has shown promising performance in the reactor core neutronics simulations. This work is focused on the development and implementation of the transport corrected interface and boundary conditions in NEM SP3 solver, following recent published work on the rigorous SPN theory for piecewise homogeneous regions. A streamlined procedure has been developed to generate the flux zero and second order/moment discontinuity factors (DFs) of the generalized equivalence theory to eliminate the error introduced by pin-wise homogenization. Moreover, several color set models with varying size and configuration are later explored for their capability of generating DFs that can produce results equivalent to that using the whole-core homogenization model for more practical implementations. The new developments are tested and demonstrated on the C5G7 benchmark. The results show that the transport corrected SP3 solver shows general improvements to power distribution prediction compared to the basic SP3 solver with no DFs or only zero order/moment DFs. The complete equivalent calculations using the DFs can almost reproduce transport solutions with high accuracy. The use of equivalent parameters from larger size color set models show better prediction in the whole-core calculations. By coupling different color set models DFs can offer the best accuracy at both eigenvalues and power distributions.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

Splines and quasi-interpolation operators are important both in approximation theory and applications. In this paper, we construct a family of quasi-interpolation operators for the bivariate quintic spline spaces S₅³ (∆_mn⁽²⁾). Moreover, the properties of the proposed quasi-interpolation operators are studied, as well as its applications for solving two-dimensional Burgers’ equation and image reconstruction. Some numerical examples show that these methods, which are easy to implement, provide accurate results.

The purpose of this paper was to analyze the development trend of hazardous chemical packaging towards low carbon economy from both qualitative and quantitative perspectives. Four types of relatively small volume packaging with volume/weight less than 450L/400kg, respectively, and three intermediate bulk containers (IBCs), which are widely used for hazardous chemicals were studied to calculate the carbon footprint (CF) from cradle to grave using life cycle assessment (LCA) method and to predict the future carbon emission of hazardous chemical packaging in the next five years (2016-2020), based on the export data of Tianjin Port in China. Grey model (GM) was adopted in the prediction. The results showed that majority of IBCs have lower carbon footprint than other types when the packaging contained same amount of same hazardous chemical. With the development of international trading, the demand of hazardous chemicals will increase as well. As the result, carbon emission generated by hazardous chemical packaging will increase accordingly. However, based on GM simulation result, increasing the amount of IBC use will effectively reduce the relative amount of carbon emission.

To overcome the difficulty of separating bastnaesite from fluorite through the flota-tion technique, the present study examined the suitability of sodium alginate (SA) as a depressant in the flotation process. The effect of SA on the flotation separation of bastnaesite and fluorite was evaluated using micro-flotation tests, zeta potential meas-urements, adsorption density measurements, Fourier infrared spectroscopy, and X-ray photoelectron spectroscopy. The micro-flotation results showed that SA exerted a strongly detrimental effect on fluorite flotation, while slightly affecting bastnaesite flotation. The surface chemistry results revealed that the -COO- and HO- functional groups in SA coordinated with Ca2+ on the fluorite surface, which induced hydro-philicity and hindered the adsorption in the subsequent collector. However, the inter-action of SA with the bastnaesite surface was marginal and did not affect the anchor-ing of the collector on the surface of bastnaesite. Based on these results, the present study proposes a possible model for the interaction of SA on the surfaces of the two minerals, laying a foundation for the flotation separation of bastnaesite from fluorite with SA as an environmentally benign depressant.

With the development of deep learning, several Graph Neural Networks (GNN)-based approaches have been utilized for text classification. However, GNNs encounter challenges in capturing contextual text information within a document sequence. To address this, a novel text classification model RB-GAT is proposed by combining RoBERTa-BiGRU embedding and a multi-head Graph ATtention Network (GAT). First, the pre-trained RoBERTa model is exploited to learn word and text embeddings in different contexts. Second, the Bidirectional Gated Recurrent Unit (BiGRU) is employed to capture long-term dependencies and bidirectional sentence information from the text context. Next, the multi-head graph attention network is applied to analyze this information, which serves as a node feature for the document. Finally, the classification results are generated through a Softmax layer. Experimental results on three benchmark datasets demonstrate that our method can achieve an accuracy of 71.48%, 98.45%, and 80.32% on Ohsumed, R8, and MR, which is superior to the existing nine text classification approaches.

This paper provides the numerical investigation of two-dimensional stochastic Navier-Stokes equation driven by additive white noises. The vorticity-stream function method is presented to calculate the incompressible fluid flow. In order to solve the formulation of steam function equation, we propose a Crank-Nicolson Fourier pseudo-spectral method. Numerical results obviously show that the presence of stochastic forcing can have an impact upon the shapes of vortex in fluid flow. To a certain extent, the phenomenon of eddy shedding and the formation of some new vortex in a random medium can be observed, which make it possible for us to conduct optimal control experiments in the development of vortex structures.

Moral observer-licensing happens when people condone others’ morally questionable conducts due to their history of moral behaviors. We investigated in four studies (N = 808) this phenomenon in the context of cyberspace and its contributing factors and boundary conditions. Study 1 determined what participants perceived as typically moral and immoral behaviors in cyberspace. Then in Study 2, participants condemned less a story character’s online immoral behavior when they were informed of the character’s prior online moral behavior than when they were not, which indicates moral observer-licensing in cyberspace. Study 3 confirmed the presence of moral observer-licensing in cyberspace and further demonstrated that a character’s prior moral or immoral behavior online respectively reduces or intensifies the negativity of the character’s subsequent immoral behavior. Finally, Study 4 showed that participants who identified with the victim in a hypothetical scenario showed less forgiveness and more condemnation of a character’s immoral behavior than those who identified with the perpetrator or the bystander. These findings are of theoretical and practical significance for our understanding of cyber ethics.

Currently, peptic ulcers are widely studied as an infectious disease caused by Helicobacter pylori primarily due to 3 supporting evidences, and this etiology may explain the other 3 observations, but cannot confront the challenges of the 15 major characteristics and the other 75 observations/phenomena of peptic ulcers. To address the challenges, a recently published Complex Causal Relationship with its accompanying methodologies was applied to analyze existing data. Peptic ulcers are identified as a psychosomatic disease triggered by psychological stress, where Helicobacter pylori plays a secondary role in only the late phase of ulceration. This new etiology elucidated all the 15 major characteristics and 81 observations/phenomena of peptic ulcers in a series of 6 articles. This sixth article focuses exclusively on the controversies surrounding the role of Helicobacter pylori in peptic ulcers. In-depth analyses find that all the 3 evidences supporting “peptic ulcers are an infectious disease caused by Helicobacter pylori” are deceiving, and 2 of the 3 explainable observations may have been misinterpreted. Meanwhile, the definitions of ‘etiological factor’ and ‘causality’ do not support ‘H. pylori infection is an etiological factor of peptic ulcers’, and existing literatures have presented a controversial view on the role of Helicobacter pylori in peptic ulcers. Interestingly, if “peptic ulcers are an infectious disease caused by Helicobacter pylori” is considered an illusion, all the characteristics of the disease, along with all the clinical, epidemiological, and laboratory observations/phenomena, can be fully understood. This illusion has misguided peptic ulcer research over the past 36 years with little progress in the field, and that may represent a widespread situation in modern medical research, resulting in a direct interference with the true understanding of disease. Evidently, keeping the concept “illusion” in mind may help remove a huge obstacle that impedes medical advance, thereby facilitating the in-depth study of disease.

The iron roughneck is an automated equipment utilized for the connection and removal of drilling tools. This paper presents the design of an integrated iron roughneck, providing a detailed introduction to its clamp body structure, along with an analysis of its structural characteristics and performance requirements. The study delves into the integration mode and working characteristics of the clamping mechanism and spin buckle mechanism for the integrated upper clamp body structure of the iron roughneck. Additionally, this paper conducts an in-depth theoretical study on the spin buckle mechanism. Firstly, it analyzes the actual working condition of the spin buckle roller from two perspectives: contact theory and rolling friction theory, determining the structural form of the spin buckle roller. Secondly, it investigates the relative displacement between the spin buckle mechanism and the drilling tool, proposing a design method for the floating device mounted on the spin buckle roller and establishing the kinematic equation of the spin buckle roller under the influence of the floating device. Furthermore, the kinematic equations of the spin buckle roller under the influence of the floating device are established. Finally, a dynamics simulation experiment is performed to simulate the working process of the spin buckle mechanism under actual working conditions, analyzing the dynamics and kinematics of the spin buckle mechanism and obtaining the relevant parameter curves of the spin buckle mechanism and drilling tools. Through data comparison and analysis, the correctness of the theoretical analysis results and the rationality of the performance and structure of the spin buckle mechanism are verified.

This study examines the Willingness-To-Pay (WTP) of consumers and the determinants of eco-labeling for the organic cocoa powder produced in the Dong Nai UNESCO Biosphere Reserve (DNBR), Southern Vietnam. Eco-labels are designed according to Tiers of eco-labeling for biosphere reserves (BR) introduced by UNESCO include BR Destination (Tier 1), BR Quality Label (Tier 2), and Professional Certification Label (Tier 3). Questionnaires are delivered to 203 customers in the DNBR and nearby places, such as Dong Nai and HCMC. This study employs a hybrid approach using descriptive statistics, ANOVA test, and Partial Least Squares Structural Equation Model (PLS-SEM). The results indicate that gender and educational level have a positive effect on consumers' preferences. Customers are willing to pay more for cocoa powder with an eco-label than one with an organic label. Perceived food safety and product knowledge lower customers’ WTP, whereas agricultural environment and pricing concerns increase it. Tier 2 is suggested for labeling cocoa powder in the DNBR. The DNBR Management Board, together with the federal and provincial governments, should all follow a similar certification process. Increased eco-label awareness is crucial for the future of environmentally responsible shopping and responsible business practices.

The power converter is the significant device in a wind power system. Wind turbine will be shut down and off grid immediately with the occurrence of the IGBT module open-circuit fault of power converter, which will seriously impact the stability of grid and even threaten personal safety. However, in the existing diagnosis strategies of power converter, there are few single and double IGBT modules open-circuit fault diagnosis methods producing negative results including erroneous judgment, omissive judgment and low accuracy. In this paper, a novel method to diagnose the single and double IGBT modules open-circuit faults of the permanent magnet synchronous generator (PMSG) wind turbine grid-side converter (GSC) is proposed. Above all, collecting the three-phase current varying with wind speed of 22 failure states including a normal state of PMSG wind turbine GSC as the original signal data. Afterward, the original signal data are decomposed by using variational mode decomposition (VMD) to obtain the mode coefficient series, which are analyzed by the proposed method base on fault trend feature for extracting the trend feature vectors. Finally, the trend feature vectors are used as the input of deep belief network (DBN) for decision-making and obtaining the classification results. The simulation and experimental results show that the proposed method can diagnose the single and double IGBT modules open-circuit faults of GSC, and the accuracy is higher than the benchmark models.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

This study provides an in-depth examination of the binary system of n-Nonadecane and 1-Octadecanol, representative of plant cuticular waxes. It emphasizes the crystallization and phase transitions in this hydrocarbon mixture. Using Differential Scanning Calorimetry (DSC) and Fourier Transform Infrared (FTIR) spectroscopy, the research uncovers detailed thermal properties and phase behaviors. The findings reveal the distinct phase transitions and enthalpy changes of each component in the binary system. This research is significant for its implications in under-standing the structural properties of plant waxes. Such insights are crucial for enhancing the effi-ciency of fertilizer and pesticide absorption in plant leaves, with broad applications in bionics and materials science. This study not only furthers the understanding of identifying specific phase transitions for each compound, facing challenges in detecting subtle changes using DSC. The re-search enhances understanding of plant cuticle waxes through FTIR analysis, revealing intricate molecular interactions and structural complexities. but also opens avenues for improved agri-cultural practices and material engineering, potentially influencing future innovations in these fields.

Abstract. Natural Thermoluminescence (TL) from the core of MD81349 marine calcareous biological ooze samples in the ninetyeast ridge of the equatorial northeast Indian Ocean and samples from the core of IODP306-U1312B in the high latitudes of the North Atlantic Ocean was studied. The spurious TL intensity of 395 °C peak is dose independent when the heating rate is 6 °C/s in a nitrogen atmosphere . TL signals exhibit a significant correlation on the marine isotope stages (MIS) at the two oceans since the mid-Pleistocene. High TL intensity corresponds to a negative δ18O in the interglacial stages, and low TL intensity corresponds to a positive δ18O in the glacial stages. TL of both cores at the two oceans reveal that the global climate has experienced eight cold and warm cycles since the mid-Pleistocene. Single-frequency spectrum analysis of MD81349 and U1312 TL in the last 300 ka was performed.Near the equator of the Northeast Indian Ocean，it is more significant that the short cycle of 38 ka and 5 ka while it is more significant that the cycle of 8 ka at the North Atlantic.In addition, correlation analysis shows that the TL has a significant positive correlation with trace elements 135Ba, a significant negative correlation with 47Ti. The impurity ions (e.g. Ba2+, Mn2+ and Ti2+) doped in carbonate are acting as activators and suppressants respectively.Time series of the TL of calcareous biological ooze tests provide an important record of climate change. The source of TL signal is also discussed.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

Imidacloprid is the first-generation neonicotinoid insecticide. But, the long-term use of im-idacloprid as a pesticide has caused severe water pollution. Recently, the toxicity of imidacloprid to aquatic organisms has received increasing attention. This study aimed to investigate the ab-sorption and distribution of imidacloprid in various tissues (gills, intestine, liver, muscle, brain, and gonads) of goldfish through short-term and continuous exposure tests for 28 days. The re-sults of short-term exposure indicated that the concentration of imidacloprid and its metabolites in tissues at the transfer stage decreased steadily after 1 day of 40 mg/l imidacloprid water treatment and was below the detection limit after 3 days. Continuous exposure for 28 days at various treatment concentrations showed that the concentrations of imidacloprid and its metab-olites differed significantly among the different tissues of the goldfish. In the 20 mg/l treatment group (S1), the highest concentration of imidacloprid was found in the liver (12.04 μg /gtissue), followed by the intestine (9.91 μg /gtissue), muscle (6.20 μg /gtissue), gill (6.11 μg /gtissue), gonads (5.22 μg /gtissue), and brain (2.87 μg /gtissue). In the 40 mg/l treatment group (S2), the order of tissue concentrations was similar to that of the S1 group, with the highest concentration observed in the liver (12.04 μg/gtissue), followed by the intestine (9.91 μg/gtissue), muscle (6.20 μg/gtissue), gill (6.11 μg/gtissue), gonads (5.22 μg/gtissue), and brain (2.87 μg/gtissue). Fur-thermore, the study detected 5-hydroxyimidacloprid, imidacloprid urea, and 6-chloronicotinic acid in imidacloprid metabolites in all tissues, while imidacloprid was detected only in the intes-tine and liver. Overall, the results of this study contribute to a better understanding of the met-abolic behavior of imidacloprid in organisms and provide new data to support the assessment of imidacloprid toxicity in fish.

When overhead lines are impacted by lightning, the traveling wave of the fault contains a wealth of fault information. The accurate extraction of feature quantities from transient components and their classification is fundamental to the identification of lightning faults. The extraction process may involve modal aliasing, optimal wavelet base issues, and inconsistencies between the lightning strike distance and the fault point, which have the potential to impact the effectiveness of recognition. This paper presents a method for identifying lightning strike faults by utilizing Kullback-Leibler (KL) divergence enhanced Variational Mode Decomposition (VMD) and Symmetric Geometry Mode Decomposition (SGMD) improved with Permutation Entropy (PE) to address the aforementioned issues. A model of a 220 kV overhead line is constructed using real faults to replicate scenarios of winding strike, counterstrike, and short-circuit. The three-phase voltage is chosen and then sub-jected to Karenbaren decoupling in order to transform it into zero mode, line mode 1, and line mode 2. The zero mode voltage is decomposed using KL-VMD and PE-SGMD methods, and lightning identification criteria are developed based on various transient energy ratios. The research findings demonstrate that the criteria effectively differentiate between winding strike, counterstrike, and short-circuit faults, thus confirming the accuracy and efficacy of the lightning fault identification criteria utilizing KL-VMD and PE-SGMD.

Brain metastasis (BrM), involving the spread of cells from a primary tumor through the blood circulation system to the brain microvasculature, eventually progresses despite multiple treatments and remains a substantial contributor to major mortality in patients with advanced- stage cancer. Molecular signatures and immune cellular components of the tumor microenvironment (TME) are emerging as essential regulators involved in establishing an organ-specific metastasis (colonization) and therapeutic response. A comprehensive understanding of detailed characterization and the immune landscape in context of process of BrM formation will greatly expand the horizon of treatments available to target these deadly diseases. In this review, we provide a comprehensive picture of the complex interactions between tumor cells and immune cellular components participated in the BrM process. Based on this knowledge, we will discuss opportunities and challenges for therapeutic strategies against BrM.

Convolutional Neural Networks (CNNs) are largely hand-crafted, which leads to inefficiency in the constructed network. Various other algorithms have been proposed to address this issue, but the inefficiencies resulting from human intervention have not been addressed. Our proposed EvolveNet algorithm is a task-agnostic evolutionary search algorithm that can find optimal depth and width scales automatically in an efficient way. The optimal configurations are not found using grid search, instead evolved from an existing network. This eliminates inefficiencies that emanate from hand-crafting, thus reducing the drop in accuracy. The proposed algorithm is a framework to search through a large search space of subnetworks until a suitable configuration is found. Extensive experiments on the ImageNet dataset demonstrate the superiority of the proposed method by outperforming the state-of-the-art methods.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Diamond-like carbon (DLC) films have a promising tribological application in green precision manufacturing, but their toughness represents a serious issue in the way of their application perspective. The film thickness is on the micrometer scale and makes conventional methods unsuitable for its toughness characterization. The absence of an accepted method for characterizing the DLC toughness has hindered the related research on the development of toughening methods and understanding the mechanism. This work intends to explore a relatively simple and acceptable characterization method to measure the film toughness. Moreover, toughening mechanisms of DLC films are proposed during the characterization to reveal the toughening mechanism. The toughness can be fully characterized through combining impact toughness and scratch toughness. The impact toughness can be obtained by observing the size of the indentation and the crack state around the indentation in the impact experiment. The scratch toughness could be assessed by combining the scratch morphology and Crack Propagation Resistance (CPRS). The improvement of film toughness should be carried out from two aspects: preventing microcrack initiation and suppressing crack propagation. Appropriate doping of non-carbide metal particles can effectively improve the toughness of the film, and there are seven main factors affecting the toughening of the film. Five toughening mechanisms of non-carbide metals from film preparation to test stage are revealed during the investigation of the change patterns.

The phycobilisome (PBS) is the major light-harvesting apparatus in cyanobacteria and red algae, a large multi-subunit protein complex of several megadaltons that is found on the stromal side of thylakoid membranes in orderly arrays. Chromophore lyases catalyse the thioether bond between apoproteins and phycobilins of PBSs. Depending on the species, composition, spatial assembly and, especially, the functional tuning of different phycobiliproteins mediated by linker proteins, PBSs can absorb light between 450 and 650 nm, making them efficient and versatile light-harvesting systems. However, basic research and technological innovations are needed, not only to understand their role in photosynthesis but also to realise the potential applications of PBSs. Synthetic biology provides an innovative approach to expand our understanding of the distinctive properties that make the PBS such an efficient light-harvesting system and to explore its heterologous synthesis, photosynthetic functions and potential medical applications. Focusing on these topics, this review describes the essential components needed for PBS assembly, the functional basis of PBS photosynthesis and the applications of phycobiliproteins. Moreover, key technical challenges for heterologous biosynthesis of phycobiliproteins in chassis cells are discussed.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

The purpose of this study is to examine the relationship between the institutional investors which can affect financial performance for corporate sustainability on the income smoothing. Therefore, this study focus on the connection between the nature of stock rights and income smoothing in China. For this study, hypotheses were established on the relationship each state-controlled companies, income smoothing, and information equilibrium of individual investors, and empirical analysis was conducted through related variables. The analysis results are summarized in three categories as follows. First, this research finds that state-controlled firms (CONTs) prefer income smoothing activities compared to non-state-controlled firms for the long-term sustainable development of firms using data from 2011 to 2019. Second, this study found out that Institutional investors support the behavior of CONTs to smooth their earnings because this behavior is seen as an attempt by CONTs to convey valuable private information to other investors. Third, we was able to discover that institutional investors' monitoring effect is predominantly driven by pressure-resistant institutional investors. This research complements the lack of empirical research on income smoothing and enable to give a guideline that the type of stock rights is a critical key determinant of participation in income smoothing activities for stable growth and sustainability in the future.

The structure characterization of two new polysaccharides from Agrocybe aegerita (AA-P) and Hygrophorus olivaceoalbus (HO-P) by HPGPC, GC-MS, NMR and FT-IR indicated that AA-P was composed of Galactose, Glucose and Arabinose, in the ratio of 3:2:1. Its skeleton structure was consisted of (1→4)-Arap, (1→4,6)-Glup and (1→6)-Galp with one branched chain. The HO-P was consisted of mannose, galactose and glucose in a ratio of 1:1:2. Its skeleton structure was consisted of (1→6)-Galactose residues, (→1)-glucose residues, (1→4)-glucose residues and (1→4,6)-D-mannose residues. There were two branched chains connected to the main chain. AA-P and HO-P had the best stimulation effect on B cells and RAW264.7 cells, respectively, and could both mainly by impacting and reducing G0/G1 phase which lead to a significant proliferation of B cells, T cells and RAW264.7 cells. In addition, AA-P and HO-P could significantly promote the secretion of TNF-α from T cells, the secretion of IgA, IgD, IgE, IgG and IgM from B cells, and the secretion of TNF-α from RAW264.7 cells, but neither of them could impact the secretion of IL-1β from RAW264.7 cells.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

This article summarizes Chinese framework for regulating artificial intelligence and integrates evolutionary game theory with cost-benefit analysis to establish a model and simulation. This framework is employed to analyze the behavioral trends among three distinct entities: governmental bodies, third-party independent institutions, and AI companies within the context of regulatory relationship. The findings indicate that: (1) The cost-benefit dynamics within the regulatory legal nexus significantly influence the behaviors of these entities; (2) Under the condition of normalized government regulation approaching full enforcement, the behavioral choices of third-party independent institutions and AI companies exhibit cyclical fluctuations.The paper draws two principal conclusions: (1) The regulatory framework need to be tailored to the specific risks presented by AI and the relative costs and benefits of legal enforcement in different jurisdictions. (2) From a cost-benefit standpoint, government intervention in AI regulation ought to be circumscribed, with government regulation focusing on critical legal risks. Other aspects of regulatory control should be delegated to cooperative legal framework that allows the participation of the independent third-party institution,which brings a nuanced and specialized approach to the governance of AI.

Classical enzyme kinetics are summarized and linked with modern discoveries here. The time course of sequential catalytic events by biological macromolecular enzyme is analyzed at the molecular level; the relationships between catalytic efficiency (turnover number), catalytic rate/velocity, the amount of time taken and physical/biochemical conditions of the system are discussed. This writing tries to connect the microscopic molecular behavior of enzyme to kinetic data obtained in experiment, and the hypothesis proposed here provide an interpretation to previous experimental observations and can be testified by future experiments.

According to the development needs of marine seismic station networking, it is necessary to develop a marine seismometer with a networking function to realize quasi-real-time and large-scale long-term observation of undersea seismic signals. This can lay a solid foundation for marine seismic research and research on earth tectonics, activities, and processes. Based on the advantages and disadvantages of the existing observation equipment, this study proposed to develop a new type of the Autonomous Glide Marine Seismometer(AGMS) that can be applied to the global sea area, focusing on the design and study of the main structure of the carrier of the AGMS. The ultimate strength of the ellipsoidal pressure-resistant spherical shell is investigated by using the finite element analysis method. A reasonable finite element analysis model is proposed through comparing the finite element parameter results with the theoretical formulas and relevant specifications. Finally, the design process and strength checking of the pressure-resistant shell of the AGMS are established. These relevant results can also provide a reference for the design of other deep-sea pressure-resistant chambers.

To deal with the uncertainties in modeling offshore wind turbines, we proposed a parameter inversion method for the pile-soil interaction model based on structural health monitoring results and the numerical model. The proposed parameter inversion method has a numerical model, an objective function selected using both the numerical and identified results, and an inverse optimization using a random search algorithm in the assumed parameter space. The parameter results in the minimum optimization objective function are identified as the in-situ parameter. The proposed method is confirmed to converge after some iterations, whatever the initial parameter values are. However, different initial parameter cases may converge to slightly different optimal parameters, implying the pile results are sensitive to geological parameters. Moreover, a comparison with the original design results shows design redundancy or risks. Though the proposed method has several flaws, it can shed some light on the influence of uncertainties in offshore wind turbines, such as soil parameters in geological surveys.

The 11 system in iron-based superconducting family has become one of the most extensively studied materials in the research of high-temperature superconductivity due to their simple structure and rich physical properties. However, the research on 11 iron-based superconductors faces numerous obstacles, mainly stemming from the challenges associated with producing high-quality single crystals. Since the discovery of FeSe superconductivity in 2008, researchers have made significant progress in crystal growth, overcoming the hurdles that initially impeded their studies. Consequently, they have successfully established the complete phase diagrams of 11 iron-based superconductors, including FeSe1-xTex, FeSe1-xSx and FeTe1-xSx. In this paper, we aim to provide a comprehensive summary of the preparation methods employed for 11 iron-based single crystals over the past decade. Specifically, we will focus on hydrothermal, chemical vapor transport (CVT), self-flux, and annealing methods. Additionally, we will discuss the quality, size, and superconductivity properties exhibited by single crystals obtained through different preparation methods. By exploring these aspects, we can gain a better understanding of the advantages and limitations associated with each technique.

Machine fault diagnosis systems need to collect and transmit dynamic monitoring signals, like vibration and current signals, at high-speed. However, industrial wireless sensor networks (IWSNs) and Industrial Internet of Things (IIoT) are generally based on low-speed wireless protocols, such as ZigBee and IEEE802.15.4. To address this tension when implementing machine fault diagnosis applications in IIoT, this paper proposes a novel IWSN with on-sensor data processing. On-sensor wavelet transforms using four popular mother wavelets are explored for fault feature extraction, while an on-sensor support vector machine classifier is investigated for fault diagnosis. The effectiveness of the presented approach is evaluated by a set of experiments using motor bearing vibration data. The experimental results show that compared with raw data transmission, the proposed on-sensor fault diagnosis method can reduce the payload transmission data by 99.95%, and reduce the node energy consumption by about 10%, while the fault diagnosis accuracy of the proposed approach reaches 98%.

To address the problems of lining cracking and spalling of tunnel structures in coastal areas under the influence of special geologic conditions, environmental loading, and the coupling effect of chemical erosion effects, hybrid fibers were introduced to fly ash concrete in this study. The working performance, compressive strength, split tensile strength, and flexural strength of the hybrid fiber fly ash concrete were tested.The NEL chloride diffusion coefficient under steady-state conditions and the durability test for resistance to sulfate corrosion were carried out. Thus, in-depth analyses of the comprehensive performance of the hybrid fiber fly ash concrete used for tunnel lining were carried out and the damage mechanism were explored. The results showed that the hybrid fiber fly ash concrete exhibited higher strength compared to the control group concrete. However, when the fibers exceeded a certain dosage, the reduction in the working properties of the concrete structure led to the creation of larger pores in the matrix structure, which in turn affected the mechanical properties of the concrete. The most significant reduction in NEL chloride diffusion coefficient was observed when both steel fibers and coconut fibers were added at 1.0 % volumetric parameter, compared to the control group. The apparent state and compressive strength after sulfate corrosion were also minimally affected. This study ensured that the mechanical properties of the concrete were improved and also substantially improved the corrosion resistance of the matrix, providing a scientific basis for the performance improvement of tunnel lining concrete, confirming that steel-coconut fibers hybrid fiber fly ash concrete has a great potential to improve the structural load bearing capacity and durability, and may provide theoretical support for the continued use of tunneling projects and construction processes.

The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

When there are multiple key strata in the overburden of deep coal seam and the surface subsid-ence coefficient after mining is small, it indicates that the overlying key strata fail to break com-pletely after mining. On this occasion, the stress concentration on the working face occurs easily, which in turn leads to the occurrence of dynamic disasters such as rock burst. This study adopted a comprehensive analysis method of field monitoring and numerical simulation to explore the in-fluence of key stratum on the evolution law of mining-induced stress in the working face. Dis-tributed optical fiber sensor (DOFS) and surface subsidence GNSS monitoring system were re-spectively arranged inside and at the mouth of the ground observation borehole. According to the monitoring results of strain obtained from DOFS, the height of broken stratum inside the overlying strata was obtained; according to the monitoring results of surface subsidence, the sur-face subsidence coefficient was proved to be less than 0.1, indicating that the high key stratum does not break completely, but enters a state of bending subsidence instead. In order to reveal the influence of key stratum on the mining-induced stress of working face, two 3DEC numerical models with and without key stratum were established for comparative analysis. As the numeri-cal simulation results show, when there are multiple key strata in the overburden, the stress in-fluence range and stress concentration coefficient of coal seam after mining are relatively large. The study revealed the working mechanism of rock burst accidents after large-scale mining and predicted the potential area of rock burst risk after the mining of the working face, which has been verified by field investigation. The research results are of great guiding significance for the revelation of the working mechanism of rock burst in deep mining condition and its prevention and control.

According to the characteristics of the sustainable development of subway traffic, the establishment process of an evaluation index system is determined, and the evaluation method and basis are defined. The evaluation index system is established from the aspects of subway traffic sustainability, economic sustainability and urban coordination sustainability. The comprehensive evaluation method of the analytic hierarchy process (AHP) model is used to calculate the weights of comprehensive evaluation indexes at each level. Finally, the sustainable development model of Shijiazhuang subway traffic is evaluated. The results show that the proposed evaluation system and model reflect the degree of sustainable development of subway traffic and can be used for reference in the evaluation of regional subway traffic sustainable development.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

State transition in the multiple-levels system has the great potential applications in the quantum technology. In this article we employ a deterministic approach in complex space to analyze the dynamics of the 1s-2p electron transition in the hydrogen atom. The electron’s spin motion is embodied in the framework of quantum Hamilton mechanics that allows us to examine the transition dynamics more precisely. The transition is driven by an oscillating electric field in the z-direction. The electron’s transition process can be visualized by monitoring its motion in the complex space. The quantum potential and the total energy proposed in this paper provide new indices to observe the dynamic changes of electrons in the transition process.

Mucosal vaccines can target specific mucosal surfaces, such as the respiratory, genital, or intestinal mucosa. Conventional systemic immunization, such as intramuscular injections, do not provide mucosal immunity, including IgA, nor do they prevent pathogens from entering the mucous membranes. Nasal immunization protects mucosal membranes, but nasal antigen presentation appears to entail adjuvant to stimulate immunogenicity. Current treatments for mucosal diseases such as inflammatory bowel disease (IBD) and allergic dermatitis only aimed to temporarily relieve symptoms. Moreover, these treatments not only have drug resistance or side effects, but the disease can recur, leading to switching to other treatments. Therefore, there is a need to develop safe and effective treatments that provide better long-term outcomes to reduce the risk of recurrence. Regulatory T (Treg) cells have been used to suppress inflammation. To find advances in mucosal treatment, we investigated the therapeutic effects of intranasal pep27 mutant immunization. Here, a new method of Treg induction through intranasal immunization without adjuvant has been developed to potentially overcome allergies and mucosal inflammation of the lung-gut axis in animal models. The implementation of the pep27 mutant for these therapies should be preceded by studies of Treg resilience through clinical translational studies of dietary changes.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Aging is associated with muscle atrophy and fatty infiltration of skeletal muscle. The multifidus muscle stabilizes the lumbar spine and undergoes adipose accumulation with age, leading to functional decline in the elderly. Therefore, quantitative assessment of the multifidus muscle can be beneficial for the elderly when formulating treatment strategies and reducing future complications. Fifty-seven patients (mean age, 73.89 ± 6.09; 23 male patients) who underwent lumbar Magnetic resonance imaging (MRI) were prospectively recruited. The cross-sectional area (CSA) of the multifidus from the L2-S1 level and the CSA of the L4-5 level psoas muscle were measured. The functional CSA (fCSA) of the multifidus muscle was measured by excluding the fat infiltration area from the multifidus CSA. The CSA to fCSA ratio was obtained by multiplying 100 by the value obtained by dividing CSA by the fCSA. Pfrrmann classification was used to evaluate the degree of disc degeneration. The functional disability measurements were the Short Physical Performance Battery (SPPB), Berg Balance Scale (BBS), grip strength, and functional reach test (FRT). Pearson's correlation analysis was used to examine the relationship between the functional disability measurements and the multifidus muscle. The CSA to fCSA ratio value was relatively constant at each spine level and showed a significant correlation with the SPPB, grip strength, FRT, and psoas index (p&lt;0.05). However, degree of disc and multifidus muscle degeneration were not statistically significant. So, age-related changes play a significant role in developing back muscle fatty infiltration than disc dgeneration. Moreover, Grip strength showed a stronger relationship with the quality of the multifidus muscle than other functional disability measurements.

A new design scheme is proposed for twisting the walls of a microchannel, and its performance is demonstrated numerically. The numerical study was carried out for a T-shaped microchannel with twist angles in the range of 0 to 34π. The Reynolds number range was 0.15 to 6. The T-shaped microchannel consists of two inlet branches and an outlet branch. The mixing performance was analyzed in terms of the degree of mixing and relative mixing cost. All numerical results show that the twisting scheme is an effective way to enhance the mixing in a T-shaped microchannel. The mixing enhancement is realized by the swirling of two fluids in the cross section and is more prominent as the Reynolds number decreases. The twist angle was optimized to maximize the DOM, which increases with the length of the outlet branch. The twist angle was also optimized in terms of the relative mixing. The two optimum twisting angles are generally not coincident. The optimum twist angle shows a dependence on the length of the outlet branch but it is not affected much by the Reynolds number.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

This study focuses on the nuanced phenomenon of gendered parenting by exploring “how” and “when” maternal son preference associates with depressive symptoms among Chinese early adolescents. Focusing on 1,093 junior high school students from a relatively affluent city in western China, the research examined the mediating roles of mother-child attachment and father-child attachment, as well as the moderating role of school connectedness in the relationship between maternal son preference and depressive symptoms. The results revealed a noteworthy positive correlation between maternal son preference and depressive symptoms among female adolescents, with no significant association observed in males. In addition, mother-child attachment and father-child attachment mediated the relationship between maternal son preference and depressive symptoms, which supported the “spillover effect” and “crossover effect”. Moreover, moderation effect analysis indicated that higher level of school connectedness can buffer the effect of maternal son preference on girls’ depressive symptoms, while lower level of school connectedness can enhance the effect of maternal son preference on girls’ depressive symptoms. These insights help to enhance people's understanding of gendered parenting, emphasizing the enduring necessity of addressing son preference within the broader context of promoting gender equality.

This study aimed to select the most effective metabolites for controlling honey bee nosemosis using culture extracts from 342 entomopathogenic fungi of 24 species from 18 genera. The germination inhibitory activity of the fungal culture extract against Nosema ceranae spores was evaluated using an in vitro germination assay method. Among 89 fungal culture extracts showing germination inhibitory activity of approximately 80% or more, 44 culture extracts that maintained their inhibitory activity even at a concentration of 1% were selected. Finally, the honey bee nosemosis inhibitory activity was evaluated using the cultured extracts of 5 fungal isolates having a Nosema inhibitory activity of approximately 60% or more even when the extract was removed after treatment. As a result, the proliferation of Nosema spores was reduced by all fungal culture extract treatments. However, only the treatment of the culture extracts from Paecilomyces marquandii 364 and Pochonia bulbillosa 60 showed a reduction in honey bee mortality due to nosemosis. In particular, the extracts of these two fungal isolates also increased the survival of honey bees.

Examining the clustering characteristics and fluctuations within urban areas during peak hours through the lens of bike-sharing is of utmost importance in the optimization of bike-sharing systems and urban transportation planning. This investigation adopts the principles of urban spatial interaction network construction and employs streets as the fundamental units of analysis to model bike-sharing activities during morning and evening peak hours within Beijing's six central districts. Subsequent to this, a comprehensive analysis of the network's structural attributes was carried out. A walktrap method rooted in modularity analysis was introduced to discern and scrutinize the clustering patterns and characteristics of communities within the network across different temporal intervals. Empirical findings reveal a predominant usage pattern of shared bicycles for short-distance travel during both morning and evening peak hours. Notably, distinctive community structures manifest during these periods, characterized by two large communities and multiple smaller ones during the morning peak, while the evening peak showcases a single large community alongside several medium-sized and smaller ones. Moreover, the extended interaction radius points to an expanded geographic range of interactions among streets. These findings bear significant implications for the management of urban transportation, bike-sharing enterprises, and urban residents, proffering valuable insights for the optimization of bike-sharing schemes and transportation strategies.

Recently, there has been considerable research on deepfake detection. However, most existing methods face challenges in adapting to the advancements in new generative models within unknown domains. In addition, the emergence of new generative models capable of producing and editing high-quality images, such as Diffusion, Consistency, and LCM, poses a challenge for traditional deepfake training models. These advancements highlight the need for adapting and evolving existing deepfake detection techniques to effectively counter the threats posed by sophisticated image manipulation technologies. In this paper, our objective is to detect deepfake videos in unknown domains using unlabeled data. Specifically, our proposed approach employs Meta Pseudo Labels (MPL) with Supervised Contrastive Learning, so-called SupCon-MPL, allowing the model to be trained on unlabeled images. MPL involves the simultaneous training of both a Teacher model and a Student model, where the Teacher model generates Pseudo Labels utilized to train the Student model. This method aims to enhance the adaptability and robustness of deepfake detection systems against emerging unknown domains. Supervised Contrastive Learning utilizes labels to compare samples within similar classes more intensively, while encouraging greater distinction from samples in dissimilar classes. This facilitates the learning of features in a diverse set of deepfake images by the model, consequently contributing to the performance of deepfake detection in unknown domains. When utilizing the ResNet50 model as the backbone, SupCon-MPL exhibited an improvement of 1.58% in accuracy compared to traditional MPL in known domain detection. Moreover, in the same generation of unknown domain detection, there was a 1.32% accuracy enhancement, while in the detection of post-generation unknown domains, there was an 8.74% increase in accuracy.