The effects of residual stress in a tungsten gate on a polysilicon channel in scaled 3D NAND flash memories were investigated using a technology computer-aided design simulation. The NAND strings with respect to the distance from the tungsten slit were also analyzed. The scaling of the spacer thickness and hole diameter induced compressive stress on the polysilicon channel. Moreover, the residual stress of polysilicon in the string near the tungsten slit had greater compressive stress than the string farther away. The increase in compressive stress in the polysilicon channel degraded the Bit-Line current (Ion) because of stress-induced electron mobility deterioration. Moreover, a threshold voltage shift (△Vth) occurred in the negative direction because of conduction band lowering.

Functional connectivity (FC) is a potential candidate that can increase the performance of brain-computer interfaces (BCIs) in the elderly because of its compensatory role in neural circuits. However, it is difficult to decode FC by current machine learning techniques because of a lack of its physiological understanding. To investigate the suitability of FC in BCI for the elderly, we propose the decoding of lower- and higher-order FCs using a convolutional neural network (CNN) in six cognitive-motor tasks. The layer-wise relevance propagation (LRP) method describes how age-related changes in FCs impact BCI applications for the elderly compared to younger adults. Seventeen younger (24.5±2.7 years) and twelve older (72.5±3.2 years) adults were recruited to perform tasks related to hand-force control with or without mental calculation. CNN yielded a six-class classification accuracy of 75.3% in the elderly, exceeding the 70.7% accuracy for the younger adults. In the elderly, the proposed method increases the classification accuracy by 88.3% compared to the filter-bank common spatial pattern (FBCSP). LRP results revealed that both lower- and higher-order FCs were dominantly overactivated in the prefrontal lobe depending on task type. These findings suggest a promising application of multi-order FC with deep learning on BCI systems for the elderly.

The physics of Hubble's law, motivated by the anomalous acceleration of Pioneer 10/11, suggests that the Hubble constant corresponds to a gravitational field of the Universe. The Hubble constant inferred from Pioneer 10/11 data is $\sim 69$ km/s/Mpc. The anomalous acceleration of Pioneer 10/11 can be interpreted as an observational evidence for Mach's principle. The redshift is an apparent value. Its intrinsic value has a limit resulting to $v

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Ultraviolet (UV) radiation has both harmful and beneficial effects on human health. It can cause skin damage and cancer, but also provides the primary source of vitamin D. Additionally, UV radiation affects energy metabolism in mice with metabolic diseases and has protective effects on hypertension and cardiovascular diseases.Metabolic Syndrome is a collection of metabolic dysfunctions such as dyslipidemia, hypertension, hyperglycemia, abdominal/central obesity, and insulin resistance. Chronic UVR exposure suppressed obesity and type 2 diabetes in high-fat diet-fed mice, while vitamin D supplementation did not replicate these effects. On the other hand, topical application of nitric oxide (NO) donors replicated UV effects on mice, and NO scavengers prevented the positive impact of UV. UVR may prevent the development of obesity and metabolic syndrome through mechanisms that depend on UVR-induced NO, not vitamin D. Exposure to sunshine has a protective impact on blood pressure and cardiovascular disease. Although lower vitamin D concentration is linked to increased hypertension and the incidence of CVD, oral vitamin D supplementation does not decrease blood pressure or the risk of CVD, indicating that vitamin D may not mediate the beneficial effects of sun exposure. Instead, NO plays a crucial role as an endogenous vasodilator, produced by the vascular endothelium. Solar UVA may release nitrogen oxides from skin storage into the bloodstream, lowering blood pressure and cardiovascular mortality.In conclusion, UVR exposure could be a promising non-pharmacological intervention for metabolic syndrome, hypertension, and CVD prevention, and NO may play a crucial role in mediating these effects. Further research is needed to explore the precise mechanisms and identify the optimal doses and exposure times of UVR.

Rammed earth in a built environment has vapor diffusion characteristics and humidity control ability each of which are respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties, which allows easily absorbing water parti-cles, hence, affecting the durability of a rammed earth wall. This paper presents the water repel-lency method for rammed earth walls which synthesizes siloxane copolymers containing fluo-rine. The water-repellent properties are investigated by measuring the contact angle, water ab-sorption rate, and compressive strength after spray coating with the synthesized siloxane co-polymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group is about 140o. The water absorption of the specimen obtained after immersing in water for 24 hours is low at about 3.5 wt.%. In addition, the compressive strength is remained more than 80% of the corresponding strength of the specimen which is not immersed into water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluo-rine group may assure the water-repellent performance and the economic competitiveness.

Objective: The main purpose of the study is to investigate the combined effects of polydeoxyribonucleotide (PDRN) and extracorporeal shock wave therapy (ESWT) sequences on the regenerative processes in atrophied animal muscles. Methods: Thirty male New Zealand rabbits, aged 12 weeks, were divided into five groups: normal saline, PDRN, ESWT, PDRN injection before ESWT, and PDRN injection after ESWT. Following 2 weeks of cast immobilization, the respective treatments were administered to the atrophied calf muscles. Radial ESWT was performed twice weekly. The evaluation included measurements of calf circumference, tibial nerve compound muscle action potential (CMAP), and gastrocnemius (GCM) muscle thickness after 2 weeks of treatment. Histological and immunohistochemical staining, as well as Western blot analysis, were conducted 2 weeks post-treatment. Staining intensity and extent were assessed using semi-quantitative scores. Results: Groups 4 and 5 demonstrated significantly greater calf muscle circumference, GCM muscle thickness, tibial nerve CMAP, and GCM muscle fiber cross-sectional area (types I, II, and total) than in the remaining three groups (p < 0.05), while they did not did not differ significantly in these parameters. Groups 2 and 3 showed the higher values for all the observations compared to group 1 (p < 0.05). Group 4 had the greatest ratio of vascular endothelial growth factor (VEGF) to platelet endothelial cell adhesion molecule-1 (PECAM-1) in the gastrocnemius muscle fibers than in the other four groups (p < 0.05). Western blot analysis revealed significantly higher expression of angiogenesis cytokines in groups 4 and 5 than in the remaining (p < 0.05). Conclusion: The combination of ESWT and PDRN injection demonstrated superior regenerative efficacy for atrophied calf muscle tissue in rabbit models than these techniques alone or saline. Particularly, administering ESWT after PDRN injection yielded the most favorable outcomes in specific parameters.

In this paper, we introduce the partially degenerate Changhee-Genocchi polynomials and numbers and investigated some identities of these polynomials. Furthermore, we investigate some explicit identities and properties of the partially degenerate Changhee-Genocchi arising from the nonlinear dierential equations.

The horizontal flatbed electrophoresis system has been used for the electrophoresis of protein samples and is often preferred for a two-dimensional polyacrylamide gel electrophoresis. In currently available equipment, cathode and anode electrodes were placed on top of a gel at each end. An electric field entered from the top of a gel, and its strength was relatively weaker in the bottom part of the gel. Such configuration caused migrating protein bands to lie down forward in the migrating direction. New electrodes, i.e., the clamp-shaped and the double-deck electrodes, were developed to simultaneously apply an electric field from the top and bottom of a gel. Electrophoretic separation with these electrodes made protein bands more focused and improved protein band resolutions. When the FIGE technique was tested together with new electrodes, protein bands were aligned nearly vertically and showed the best electrophoretic resolutions.

A two-year-old male Pomeranian dog visited the hospital due to side effects of surgical correction for patellar luxation. Stifle joint arthrodesis (SJA) was performed on the patient’s right leg using autologous bone grafting techniques. The right leg’s femur and tibial joint were angled 120-130◦ and the SJA plate was fixed on the front of the two bones. After performing joint fusion of the right limb, medial patellar luxation (MPL)-corrective surgery was performed to cut the tibial tuberosity on the left leg and the fixing force was increased using the figure-of-eight tension band wiring technique. The results were observed for walking and trotting of the right hind limb, evaluated for 27 days after surgery. It was difficult for the patient to walk because weight loading was not performed for 3 days after surgery; short strides and partial weight bearing were possible 5 to 7 days after surgery. After 10 days, the patient was able to move while bearing weight with a slight disruption. For trotting, the patient showed intermittent normal steps 5 to 7 days after surgery, but the disruption continued. After 14 days, trotting was possible and movements were shown to be maintained during everyday activities.

Burrs form due to plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through experiments. Based on this new objective function, a prediction of deburring performance on the burr edge of the intersecting holes with offset was performed. The results between the predicted and experimental observation results were in reasonable agreement.

Aim The use of prophylactic antibiotics prior to colorectal surgery reduces surgical site infections. Cefazolin and metronidazole is a standard regimen. Ampicillin-sulbactam may be an alternative, but the data are limited. We compared the efficacy of ampicillin-sulbactam with cefazolin and metronidazole as prophylactic antibiotics. Methods Patients who underwent colorectal surgery at Inha University Hospital between 2010 and 2020 were treated prophylactically with cefazolin and metronidazole or ampicillin-sulbactam, and observed for 30 days following surgery. The primary outcome was surgical site infections. Secondary outcomes were deep/organ infections and the need for drainage. Results SSIs occurred in 2.6% (17/646) of the ampicillin-sulbactam group and was not inferior to the occurrence in the cefazolin and metronidazole group (3.8%, 21/556). There was no significant difference between the two groups in the secondary outcomes. Conclusion Compared with the cefazolin and metronidazole combination, the ampicillin-sulbactam group is non-inferior as a preoperative prophylactic antibiotic regimen for colorectal surgery.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

In patients with unilateral tinnitus with normal hearing, several studies have compared the ipsilateral and contralateral ears; however, few studies have investigated its relationship with the duration of tinnitus. We compared the auditory brainstem response and otoacoustic emission parameters between ipsilateral and contralateral ears in adults with unilateral tinnitus and normal hearing. This retrospective review included 84 patients with unilateral tinnitus and normal hearing who underwent auditory brainstem response and otoacoustic emission; they were categorized according to the duration of tinnitus. The latencies and amplitudes of waves I, III, and V, and V/I ratio of both ears in auditory brainstem response, and the results of distortion-product otoacoustic emission and transient evoked otoacoustic emission were examined. The auditory brainstem response parameters, distortion-product otoacoustic emission parameters, and transient evoked otoacoustic emission parameters between the ipsilateral and contralateral ears along the duration of tinnitus were analyzed. Moreover, the failure rates of both distortion-product otoacoustic emission and transient evoked otoacoustic emission between the ears along with the duration and the effects of the variables on the amplitude and latency of each wave were examined. Although there was little significant difference between the ipsilateral and contralateral ears, laterality seemed to have an effect on wave I latency in the multiple linear regression analysis. The distortion-product otoacoustic emission failure rate of the ipsilateral ear was higher than that of the contralateral ear in all patients. However, there was no remarkable difference between the ears in the distortion-product otoacoustic emission and transient evoked otoacoustic emission parameters throughout the duration. We found that outer hair cells and the distal portion of the cochlear nerve are possible pathologic lesions in tinnitus with normal hearing and cochlear synaptopathy could be suspected. Further studies, including those on inner hair cells and higher central cortex, are needed.

In this paper, we present a study of various ZnO/SiO2-stacked thin film structures for flexible micro-energy harvesting devices. Two groups of micro-energy harvesting devices, SiO2/ZnO/SiO2 micro-energy generators (SZS-MGs) and ZnO/SiO2/ZnO micro-energy generators (ZSZ-MGs), were fabricated by stacking both SiO2 and ZnO thin films, and the resulting devices were characterized. With a particular interest in the fabrication of flexible devices, all the ZnO and SiO2 thin films were deposited on ITO-coated PEN substrates using an RF magnetron sputtering technique. The effects of the thickness and/or position of the SiO2 films on the device performance were investigated by observing the variations of output voltage in comparison with that of a control sample. As a result, compared to the ZnO single-layer device, all the ZSZ-MGs showed much better output voltages, while all the SZS-MG showed only slightly better output voltages. Among the ZSZ-MGs, the highest output voltages were obtained from the ZSZ-MGs where the SiO2 thin films were deposited using a deposition power of 150 W. Overall, the device performance seems to depend significantly on the position as well as the thickness of the SiO2 thin films in the ZnO/ SiO2-stacked multilayer structures, in addition to the processing conditions.

Using the World Bank Global Findex Database for 91 countries in 2014, 2017, and 2021, we examine whether fintech levels influence bank performance and whether fintech’s interaction with GDP per capita causes differential effects on bank performance globally. Since fintech levels were already very high for rich countries when the World Bank started providing fintech development statistics in 2014, we estimate AbFintech by regressing fintech levels on GDP per capita by year. AbFintech is the difference between the fintech level and its fitted values. Then, using multiple regression analyses, we investigate the impact of AbFintech on bank performance worldwide, focusing on the differential effects of AbFintech and GDP levels on bank performance. We find AbFintech significantly increases bank performance, primarily in less developed countries. Specifically, AbFintech increases banks’ ROA in the least developed countries and net interest margin in the 75th percentile countries. Also, AbFintech decreases the cost-to-income ratio in the 75th percentile countries, while it increases the ratio in the most developed countries. AbFintech does not affect the ratio of noninterest income to total income, regardless of the level of economic development.

Changes in extreme weather patterns are expected under climate change. In this study, a risk assessment was conducted using 4 building damage history datasets and 33 weather datasets (precipitation, wind speed, snow, and temperature) from 230 regions in South Korea to quantitatively analyze and predict building damage caused by potential future natural disasters. Decision tree analysis was used to evaluate building damage risk in 230 regions. The decision tree model to determine the risk of flood, gale, and typhoon was generated, which excluded gales, with less damage. The weight (variable importance) and limit value (damage limit) of the weather variables ware derived using the decision tree model. Using these two factors, we assessed the building damage risk in 230 regions in South Korea until 2100. The number of regions at risk of flood damage increased by more than 30% in average. Conversely, regions at risk of snowfall damage decreased by more than 90%. The regions at risk of typhoons decreased by 57.5% on average, and the number of regions at high risk of typhoon damage increased by up to 62.5% in RCP 8.5. These results can be used as objective data to minimize future building damage throughout South Korea, representing the first step towards sustainable development in the region with respect to disaster response.

In this paper, we represent the generating function of w-torsion Fubini polynomials by fermionic p-adic integral on Z_p. Then we consider a quotient of such fermionic p-adic integrals on Z_p, representing generating functions of three w-torsion Fubini polynomials and derive some new symmetric identities for the w-torsion Fubini and two variable w-torsion Fubini polynomials.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

This study develops an intelligent fire suppression device that links microcapsule-based IoT to extinguish early fires, such as blind spots that cannot be seen by humans or places that are difficult to recognize fires. The microcapsule is a micro-unit collection that collects Novak 1230 gas generated in the semiconductor production process. The microcapsule is molded into a form with a fire suppression function, and when a fire occurs, the molded body explodes and absorbs ambient oxygen to suppress the fire. The complex sensor IoT executes smoke and heat detection generated when a fire is suppressed within 10 seconds, which derives the reliability of the detector by notifying the fire and detecting the ignition point through communication linkages such as Ieee 485 and WiFi or LoRa.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

Recent prolonged dry periods and lack of irrigation water have severely affected the productivity of coffee farms’ in the Central Highlands of Vietnam. This paper analyzes the efficiency of irrigation water use for Robusta coffee (Coffea canephora) in Lam Dong province, Highlands, Vietnam. A Cobb-Douglas production function was used to determine coffee productivity’s response to the application of irrigation water and other production factors using data collected from 194 farmers while the Technical Efficiency (TE) and Irrigation Water Use Efficiency (IWUE) were analyzed using a Data Envelopment Analysis (DEA) model. The correlation of different factors to IWUE was determined using the Tobit model. The production function analysis using Cobb-Douglas shows that the volume of irrigation water, amount of working capital, labor and farm size significantly influence coffee productivity. It also shows that indigenous farmers are more efficient in utilizing irrigation water than the (mostly Kinh) migrant farmers. The Tobit result, on the other hand. indicates that farmers’ experience, education level, distance of farm to water source, security of access to water source, extension contact and credit access significantly affect IWUE. The study findings further suggest that mitigating water shortages in coffee farms require sub-regional and national policy support such as better access to credit and extension services, training, land management and household-level effort to improve farming practices, through the application of appropriate technologies and traditional knowledge.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

Bayesian nonlinear mixed effects models for data in the form of continuous, repeated measurements from a population, also known as Bayesian hierarchical nonlinear models, are a popular platform for analysis when interest focuses on individual specific characteristics and relevant uncertainty quantification. Due to the limitation of computational power, this framework was relatively dormant until the late 1980s, but in recent years, the statistical research community saw vigorous development of new methodological and computational techniques for these models, the emergence of software, and wide application of the models in numerous industrial and academic fields. This article presents an overview of the formulation, interpretation, and implementation of Bayesian nonlinear mixed effects models and surveys recent advances and applications.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

This study aims to evaluate the climate-change response of greening persistently vacant houses and barren sites in deteriorated high-density residential areas in old downtown metropolitan areas. The current status of building demolition sites in Ami-dong and Chojang-dong, Busan Metropolitan City, was examined. In this area, of the 340 vacant houses from 2017, 246 (72.35%) remained persistently vacant till 2020. In 2020, 213 barren sites were neglected after building demolition. Amongst these sites, 177 (83.10%) were paved with concrete. Persistently vacant houses and barren sites were afforested, and the climate-change response was quantified in terms of flood reduction and CO2 mitigation in four scenarios (current, concrete, ground cover plants, and trees). Runoff analysis was performed using the Korea low-impact development model (K-LIDM) to assess flood mitigation. The tree scenario showed average runoff mitigations of 1.71%, 2.38%, and 3.06% in the long-term, 30-year, and 2-year rainfall scenarios, respectively. Additionally, 3058 deciduous broadleaf trees may be planted in the study area to promote CO2 mitigation. Thus, an additional annual carbon fixation of 62,123.78 kg CO2 may be expected. The greening of vacant houses and demolished sites was effective in all aspects of the climate-change response, and tree-based greening exhibited the most significant effect.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

With the rapid spread of carbon trading in the global economy, the interactions of prices between carbon (or clean/renewable energy) and traditional fossil energies such as coal and oil have raised growing attention, but little research have discussed their dynamic volatility spillover and time-varying correlation. The purpose of this study is to investigate these issues, for the weekly data of EUA futures, Biofuel and Brent oil prices from 25 October 2009 to 5 July 2020. We employ the VAR-GARCH model with the BEKK specification. Our results are summarized as follows. At first, we identified the sudden changes and the volatility persistence in the three markets, and also confirmed that the volatility of the markets has changed significantly over time. Secondly, we find that there are a weak volatility spillover effect among the three markets, while a strong spillover effect between the EUA and Brent oil markets. Lastly, in financial markets, the EUA can be used as a hedging portfolio for the Biofuel and Brent oil markets. These results can help investors to well compose their portfolios and manage their investment risks, and help potential pollutant emission sources to join in carbon market in a cost-effective way.

Whole blood viscosity, a hemorheological factor, is currently used for diagnosis, as it is correlated with various vascular diseases that are difficult to diagnose early with a general blood test. It was determined that it was necessary to set reference intervals for further studies and utilization of whole blood viscosity in cats, a representative companion animal, and this study was conducted. 50 healthy cats were recruited for the study and whole blood viscosity, complete blood count, and serum chemistry tests were performed. The reference intervals of whole blood viscosity were 15.169 to 43.684 cP at a shear rate of 1 s-1 reflecting diastole, and 3.524 to 5.544 cP at a shear rate of 300 s-1 reflecting systole. Red blood cells, hematocrit, hemoglobin, white blood cells, and neutrophils in the complete blood count, and total protein, albumin, globulin, and cholesterol in the serum chemistry were significantly correlated with whole blood viscosity. The results of this study set reference intervals of whole blood viscosity for healthy cats in a wide shear rate range that has not yet been fully established and investigated its correlation with other blood indicators.

The Boltzmann-Gibbs (BG) entropy has been used in a wide variety of problems for more than a century. It is well known that BG entropy is extensive, but for certain systems such as those dictated by long-range interactions, the entropy must be non-extensive. Tsallis entropy possesses non-extensive characteristics, which is parametrized by a variable q (q = 1 being the classic BG limit), but unless q is determined from microscopic dynamics, the model remains but a phenomenological tool. To this date very few examples have emerged in which q can be computed from first principles. This paper shows that the space plasma environment, which is governed by long-range collective electromagnetic interaction, represents a perfect example for which the q parameter can be computed from micro-physics. By taking the electron velocity distribution function measured in the heliospheric environment into account, and considering them to be in quasi equilibrium state with electrostatic turbulence known as the quasi-thermal noise, it is shown that the value corresponding to q = 9/13 = 0.6923 may be deduced. This prediction is verified against observation made by spacecraft, and it is shown to be in excellent agreement.

Wireless Sensor Network is an emerging technology and the collaboration of wireless sensors becomes one of the active research areas to utilize sensor data. Various sensors collaborate to recognize the changes of a target environment, to identify, if occurs, any radical change. For the accuracy improvement, the calibration of sensors has been discussed, and sensor data analytics are becoming popular in research and development. However, they are not satisfactorily efficient for the situations where sensor devices are dynamically moving, abruptly appearing or disappearing. If the abrupt appearance of sensors is a zero-day attack and the disappearance of sensors is an ill-functioning comrade, then sensor data analytics of untrusted sensors will result in an indecisive artifact. The pre-defined sensor requirements or meta-data based sensors verification is not adaptive to identify dynamically moving sensors. This paper describes a deep-learning approach to verify the trustworthiness of sensors by considering the sensor data only, without having to use meta-data about sensors or to request consultation from a cloud server. The contribution of this paper includes 1) quality preservation of sensor data for mining analytics and 2) authenticity verification of dynamically moving sensors with no external consultation.

As the global semiconductor market is growing steadily, the need for optimization of the man-ufacturing process is paramount. For example, in the process of transferring the semiconductor chips to the substrate, each chip needs to be individually separated from the dicing tape via a plunger. In this process, however, the fixed chip is not easily removed from the tape due to strong adhesion, and the chip can become damaged if it is forcibly pulled out. Therefore, the present paper reports the development of functional adhesive tapes that initially adhere strongly to the semi-conductor chip on the dicing tape but can be easily removed after transfer. The fabricated functional tape has an initial adhesion of 350 gf, which enables firm fixing of the semiconductor chip to be transferred, and a final adhesion of 0.8 gf after UV curing, thereby facilitating removal of the chip without damage after transfer. Therefore, the fabricated functional tape is expected to contribute to the optimization of the semiconductor manufacturing process and is expected to be useful in the semiconductor package manufacturing process.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

Energy and Environment Tax is used globally as a means of environment policy. Energy and Environment tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy and environmental taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy and environmental taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and to suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy and environmental taxes. Results of this study show that South Korea’s energy and environmental taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy and environmental tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy and environmental taxation. However, energy and environmental taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy and environmental taxation

Cardiovascular-related diseases are one of the leading causes of death worldwide. An understanding of heart movement based on images plays a vital role in assisting the procedure in the postoperative and postoperative processes. In particular, if the shape information can be provided in real-time using the electrocardiogram(ECG) signal using this information, the heart’s movement information can be used for cardiovascular analysis and imaging guides during surgery. In this paper, we propose creating a 3D+t cardiac coronary artery model that is rendered in real-time according to the ECG signal. Hierarchical cage-based deformation modeling is used to generate mesh deformation used during the procedure according to the ECG signal. We match the blood vessel’s lumen obtained from the ECG-gated 3D+t CT angiography taken at the multiple cardiac phases to derive the optimal deformation. Splines for 3D deformation control points were used to continuously represent the obtained deformation at the multi-view according to the ECG signal. To verify the proposed method, we compared the manually segmented lumen and results of the proposed method for eight patients. The average distance and dice coefficient between the two models was 0.543mm and 0.735, respectively. The required time for registration of the 3D coronary artery model is 23.53 seconds/model. rendering speed to derive the model according to the ECG signal after generating the 3D+t model is faster than 120 FPS.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

Energy taxation is used globally as a means of energy policy. Energy tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy taxes. Results of this study show that South Korea’s energy taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy taxation. However, energy taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy taxation.

Powdery mildew disease, caused by Sphaerotheca fusca, is a major disease affecting cucumbers cultivated in greenhouses. This study was conducted to find defense genes induced by DL-3-amino-butyric acid (BABA) and powdery mildew in cucumber. The 2000 and 5000 mg/L BABA treated cucumber exhibited disease severity of 25% and 5%, respectively, whereas the water treated cucumber leaves were severely infected, with a disease severity of 90%. BABA did not effect spore germination of the powdery mildew pathogen,. showing BABA is not antifungal agent against the pathogen. In quantitative real-time PCR analysis, BABA treated cucumber upregulated transcriptional level of the defense genes CsPAL, CsPR3,CsPR1, CsLOX1, CsLOX23, Cs LecRK6.1, CsWRKY20, and Cupi4 in cucumber to maximum levels at 48 h, whereas CsLecRK6.1 reached maximum expression after 24 h and futher salicylic acid (SA) levels were significantly increased in BABA-treated cucumber plants. In addition, the infected cucumber with powdery mildew enhanced the expression levels from1.6 to 47.3 fold of the defense genes PAL, PR3, PR1, Lox1, Lox 23, LecRK6.1, WRKY20, and Cupi4 compared to heathy cucumber. The results suggests the BABA induced defense response is associated with SA signal pathway-dependent systemic acquired resistance (SAR) in cucumber, which is involved in plant resistance mechanisms.

In recent years, due to the low energy utilization of the whole life-cycle of buildings and the di-minished indoor and outdoor comfort of buildings and the impact on the surrounding environ-ment caused by the carbon emissions of the building life-cycle, the establishment of a whole life- cycle carbon emission model for buildings to improve their energy utilization at all stages of their life-cycle has received unprecedented attention. In China, the construction industry has become a major carbon emitter, and traditional houses, as a green development building type, are an effec-tive way to achieve carbon neutrality in buildings, but the existing green building evaluation system lacks quantitative indicators of carbon emissions in the building life-cycle. The exclusive evaluation indexes for regional and characteristic buildings, such as traditional houses, are ne-glected; This study explored the formula for calculating the life-cycle carbon emissions model of traditional residential houses under a carbon emission intervention and used real measurements of the physical environment and comparative analysis of the limitations of existing local stand-ards; The results showed that the carbon emission calculation formulas for each stage of the life-cycle of traditional residential houses must be established by combining the selection of local building materials, and the materials for sustainable energy and carbon sinks of green systems. Based on the results of indoor and outdoor heat and humidity environmental tests of residential houses and an analysis of the limitations of existing evaluation indexes due to locality, four im-portant factors affecting locality green buildings in terms of energy utilization, site ecology and landscape, land saving and material saving were extracted; on this basis, the whole life-cycle carbon emission model of traditional residential houses is constructed by combining the existing green building evaluation standards with the carbon emission indexes of the life-cycle of tradi-tional residential houses.

The present study was conducted to investigate the comparative effects of organic and inorganic forms of sulfur, methyl sulfonyl methane (MSM) and sodium sulfate (SS), on laying performance, egg quality, ileal morphology, ileal volatile fatty acids, and antioxidant and stress markers in various biological samples in aged laying hens. A total of 144, 73-week-old Lohman Brown-Lite laying hens were randomly assigned to one of three experimental diets: basal diet (CONT), CONT + 0.2% MSM (MSM), and CONT + 0.3% SS (SS). The trial lasted for 12 weeks. MSM and SS groups contained 0.07% of sulfur, either organic or inorganic. Dietary MSM did not affect egg production and feed conversion ratio at 12 weeks compared with the CONT group. Dietary sulfur did not affect egg quality except for Haugh unit at 4 weeks which was lowered (P &lt; 0.05) in the SS group. Compared with the CONT group, higher (P &lt; 0.05) villus height and crypt depth ratio was observed in the SS group. None of dietary sulfur affected the percentages of short-chain fatty acids in the ileum. Total antioxidant capacity of liver increased (P &lt; 0.05) in laying hens fed MSM- and SS-added diets compared with the CONT group. The MSM and SS groups lowered (P &lt; 0.05) malondialdehyde (MDA) concentration in serum samples compared with the CONT. Finally, dietary MSM had the lowest (P &lt; 0.05) MDA concentrations in yolk samples. Taken together, our study showed that dietary organic and inorganic sulfur have positive effects on ileal morphology and antioxidant capacity in laying hens. However, SS-mediated inhibition in laying performance needs to be clarified.

We introduce the lower chaos grade of a real-valued function F defined on the Markov triple (E,μ,Γ), where μ is a probability measure and Γ is the carré du champ operator. As an application of this concept, we obtain the better estimate of the four moments theorem for Markov diffusion generators worked by Bourguin et al (2019). For our purpose, we need to find the largest number except zero in the set of eigenvalues corresponding to its eigenfunction in the case where the square of a random variable F, coming from a Markov triple structure, can be expressed as a sum of eigenfunctions, We give some examples of eigenfunctions of the diffusion generators such as Ornstein-Uhlenbeck, Jacobi and Romanovski-Routh. In particular, two bounds, called the four moments theorem and fourth moment theorem respectively, will be provided for the normal approximation of the case where a random variable F comes from eigenfunctions of a Jacobi generator.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

Using traditional methods based on detection rules written by human security experts, there is a significant challenge in accurately detecting many network threats that are increasingly becoming sophisticated. In order to deal with the limitation of the traditional methods, network threat detection techniques utilizing artificial intelligence technologies such as machine learning are being extensively studied. Research has also been conducted on analyzing various string patterns in network packet payloads through natural language processing techniques to detect attack intent. However, due to the nature of packet payloads containing binary data as well as text data, a new approach is needed that goes beyond typical natural language processing techniques. In this paper, we study a token extraction method optimized for payloads using n-gram and byte pair encoding techniques. Furthermore, we generate embedding vectors that can understand the context of the packet payload using algorithms such as Word2Vec and FastText. We also compute the embedding of various header data associated with packets, such as IP addresses and ports. Given the combination of these features, we ensemble a text 1D-CNN and a multi-head attention network in a novel fashion. We validated the effectiveness of our classification technique with the CICIDS2017 open dataset and over half a million data collected by The Education Cyber Security Center (ECSC) currently operating in South Korea. The proposed model showed remarkable progress compared to previous studies, demonstrating a highly accurate classification performance with an F1-Score of 0.998. Our model can also preprocess and classify 150,000 network threats per minute to help security agents in the field divert their time to analyzing more complex attack patterns.

In-depth insights into the profound impacts of climate change and human activities on water resources are garnered through the dynamic changes in surface water, a crucial aspect of effective water resource management and the preservation of aquatic ecosystems. This paper introduces an innovative approach employing the random forest algorithm for the systematic extraction and monitoring of surface water at large regional or national scales. This method integrates spectral bands, spectral indices, and digital elevation model data, offering a novel perspective on this critical task. A data filling model is proposed to mitigate the impact of missing data due to cloud cover. Leveraging the capabilities of the Google Earth Engine (GEE), detailed information on surface water dynamics during the rainy and dry seasons in the Yangtze River Basin (YRB) from 1991 to 2021 is extracted using Landsat time series imagery. The analysis encompasses spatial-temporal variation characteristics and trends, with a specific focus on the intricate interplay between the areal extent of surface water and hydro-meteorological factors in each sub-basin of the YRB. Importantly, this includes considerations of potential groundwater contributions to surface water. Key findings from our research include: (1) Achieving a remarkable overall accuracy of 0.96 ± 0.03 in obtaining reliable surface water datasets with the support of GEE. (2) Identifying significant trends, such as a noteworthy increase in rainy season surface water bodies (+248.0 km2·yr−1) and a concerning decrease in surface ice/snow cover during both rainy and dry seasons, with change rates of −39.7 km2·yr−1 and −651.3 km2·yr−1, respectively. (3) Uncovering the driving mechanisms behind these changes, revealing positive correlations between the areal extent of rainy season surface water bodies and precipitation, as well as negative correlations between surface ice/snow cover area and average surface skin temperature. It is crucial to note that these driving factors exhibit variation among secondary river systems, underscoring the complexity of surface water dynamics. Furthermore, comparative analyses with existing surface water products are conducted, contributing to a deeper understanding of the advantages and uncertainties inherent in our proposed extraction method. The proposed method for large-scale surface water extraction not only enhances the monitoring of spatio-temporal surface water dynamics in the YRB but also provides valuable insights for the sustainable utilization and protection of water resources, considering the potential role of groundwater in supplementing surface water.

The purpose of this study is to compare and analyze the kinematic characteristics of the upper limb segments during the archery shooting of Paralympic Wheelchair Class archers (ARW2 - second wheelchair class – paraplegia or comparable disability) and Paralympic Standing Class archers (ARST - standing archery class – loss of 25 points in the upper limbs or lower limbs), where archers are classified according to their disability grade among elite disabled archers. The participants of this study were selected as seven elite athletes with disabilities, 4 ARW2, and 3 ARST. The analysis variables were 1) the time required for each phase, 2) the angle of inclination of the body center, 3) the change of trajectory of body center, and 4) the change of movement locus of bow center by phase when performing six shots in total. The ARW2 group showed a longer time than the ARST group, and the angle of the body did not show a significant difference between the two groups. Although there was no significant difference in the mean score between the two groups, it was judged that kinematic performance according to each group was, in that there was a measurable variation in kinematic variables.

Changes in crude oil price affect the shipping freight market in three different channels. This study explores the dependence structure between oil prices and maritime freight rates to identify the strongest channel. Therefore, it investigates the relationship between oil prices and three major maritime freight rates; the Baltic Dry Index (BDI), the Baltic Dirty Tanker Index (BDTI), and the Baltic Clean Tanker Index (BCTI). We employ the decomposition method, not studied in the existing literature. The copula approach identifies the time-varying effects and asymmetry in the tail dependence structure between oil prices and freight rates. The main results of this analysis are as follows. The decomposed components display different conditional dependence patterns, and asymmetry is revealed in the upper and lower tail dependence. In the long run, we find more dependence in extreme periods like the financial crises. In short-run fluctuations, we find the dependence increases in an economic boom. The implications of the results suggest that dependence can vary over time and may change depending on extreme events, implying that the complementary strategies of the long run and short run should be different.

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p&lt;.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p&lt;.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p&lt;,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

The development of technology that combines supercapacitors and lithium-ion batteries by externally connecting them in parallel is ongoing. This study examines the correlation between the volume ratio and electrical characteristics of a cell made by internally connecting a battery capacitor with Li4Ti5O12 as the anode active material and a supercapacitor in parallel. It was found that increasing the volume occupied by the battery capacitor in the cell led to increased cell energy and resistance, resulting in decreased output characteristics. Conversely, increasing the volume occupied by the supercapacitor in the cell led to a decrease in the IR drop during discharge and cell temperature when evaluating cycle characteristics with a current of 20C. The study also examined the behavior of the current distributed during the charging and discharging process based on the volume ratio of the supercapacitor and the battery capacitor. Analyzing the correlation between the volume ratio and electrical characteristics of supercapacitors and battery capacitors could potentially lead to the development of a new type of energy storage device.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

Exposure to particulate matter (PM) causes considerable breathing-related health risks. We assessed the inhibitory effect of Siraitia grosvenorii extract (SGE) on airway inflammation in mice exposed to a fine dust mixture of PM10 (PM diameter &lt; 10 mm) and diesel exhaust particles (DEPs) known as PM10D. SGE attenuated neutrophil infiltration and the number of immune B and T cells in lung tissue and bronchoalveolar lavage fluid (BALF) of PM10D-exposed mice. SGE reduced the secretion of cytokines and chemokines, including interleukin (IL)-1a, tumor necrosis factor (TNF)- a, IL-17, chemokine (C-X-C motif) ligand (CXCL)-1, and macrophage inflammatory protein (MIP)-2 in BALF. Airway inflammation, accumulation of inflammatory cells, and collagen fibrosis in the lung after PM10D exposure were investigated by histopathological analysis, and SGE treatment ameliorated these symptoms. SGE decreased the mRNA expression of mucin 5AC (MUC5AC), CXCL-1, TNF-a, MIP-2, and transient receptor potential vanilloid and ankyrin 1 ion channels in the lung tissues of mice. Furthermore, SGE ameliorated mitogen-activated protein kinase (MAPK)/nuclear factor-kappa B (NF-κB) signaling activated by PM10D in mice. We conclude that SGE attenuated PM10D-induced neutrophilic airway inflammation via inhibiting MAPK/NF-κB activation. These results show that SGE may be a candidate for the treatment of inflammatory respiratory diseases.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

Malnutrition and cognitive dysfunction are typical features of alcoholic liver disease (ALD) and are correlated with the development of complications. The aim of this study is to explore the effect of nutritional state and diet on cognitive function in ALD. A total of 43 patients with compensated alcoholic cirrhosis were enrolled, and neuropsychological test was assessed according to body mass index (BMI, &lt;22 and ≥22). In the ALD animal study, mice were divided into 5 groups (n=9/group; normal liquid, 5% EtOH+regular liquid, 5% EtOH+high-carbohydrate liquid, 5% EtOH+high-fat liquid, and 5% EtOH+high-protein liquid diet) and fed the same calories for 8-week. To assess cognitive function, we performed T-maze studies weekly before/after alcohol binging. In cognitive function (BMI &lt;22 /≥22), language score of Korea mini-mental state (7.4±1.4/7.9±0.4), Rey-complex figure (72.0±25.9/58.4±33.6), Boston naming (11.7±2.7/13.0±1.8), forward digit span (6.7±1.8/7.5±1.6), Korean Color Word Stroop (24.2±26.5/43.6±32.4), and interference score (33.9±31.9/52.3±33.9) revealed significant differences. In the T-maze test, alcohol significantly delayed the time to reach food, and binge drinking provided a temporary recovery in cognition. The alcohol-induced delay was significantly reduced in the high-carbohydrate and high-fat diet groups. Synaptic function exhibited no changes in all groups. Cognitive dysfunction is affected by nutritional status and diet in ALD.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

To decrease oral pathogens and increase the number of beneficial bacteria, probiotics and bioactive compounds made via microbial bioconversion are recently used. In addition, the interest regarding probiotics-mediated bioconversion with popular medicinal plants is increasing. These compounds produced during the process exhibit synergistic effect and enhance a variety of biological activities including pathogen inhibition in host. Therefore, we developed bioconverted milk with high inhibitory activity against oral pathogens and α-glucosidase. Lactiplantibacillus plantarum SMFM2016-RK was chosen as the probiotic due to its beneficial characteristics such as high acid and bile tolerance, antioxidant activity, and α-glucosidase inhibition. Based on the minimal bactericidal concentration against three oral pathogens, the following appropriate concentrations of Artemisia herba-alba extract were added to milk: 5 mg/mL of A. herba-alba ethanol extract and 25 mg/mL of A. herba-alba hot-water extract. Four bioconverted milks (BM), BM1, BM2, BM3, and BM4, were produced by combining L. plantarum SMFM2016-RK alone, L. plantarum SMFM2016-RK and ethanol extract, L. plantarum SMFM2016-RK and hot-water extract, and L. plantarum SMFM2016-RK with both extracts. As a result of antimicrobial activity, BM3 inhibited the growth of Aggregatibacter actinomycetemcomitans and Porphyromonas gingivalis the most, and BM4 suppressed the growth of Fusobacterium nucleatum the most. In addition, bioconverted milk containing A. herba-alba (BM2, BM3, and BM4) inhibited α-glucosidase more effectively than BM1. In conclusion, A. herba-alba-added milk bioconverted by L. plantarum SMFM2016-RK displayed the growth inhibitory effect on oral pathogens and the α-glucosidase inhibitory activity, thus it necessitates to evaluate the effects on the alleviation of oral diseases and glycemic control through future animal experiments.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

The inhibition of alpha-glucosidase and alpha-amylase is one of clinic strategies for remedy the type II diabetes. Herbal medicines are reported to alleviate hyperglycemia. However, the constituents from those sources whether are targeted to the alpha-glucosidase and alpha-amylase still unexplored. This study attempted to select the compounds for efficacy of hypoglycemia via cellular and mouse levels. The results illustrated that the cytotoxicity in all tested compounds at various concentrations except the concentration of 16-hydroxy-cleroda-3,13-dine-16,15-olide (HCD) at 30 µM were not significant difference (p > 0.05) when compared with the untreated control. Acarbose (reference drug), Antroquinonol, Catechin, Quercetin, Actinodaphnine, Curcumin, HCD, Docosanol, Tetracosanol, Berberine, and Rutin could effectively inhibit the alpha-glucosidase activity of Caco-2 cells when compared with the control (maltose). The compounds (Curcumin, HCD, Tetracosanol, Antroquinonol, Berberine, Catechin, Actinodaphnine, and Rutin) could reduce blood sugar level at 30 min in tested mice. The effects of tested compounds on area under curve (AUC) were significant (p < 0.05) among Acarbose, Tetracosanol, Antroquinonol, Catechin, Actinodaphnine, and Rutin along with Berberine and Quercetin. In in vitro (alpha-glucosidase) with in vivo (alpha-amylase) experiments suggest that bioactive compounds can be a potential inhibitor candidate of alpha-glucosidase and alpha-amylase for the alleviation of type II diabetes.

During the last two decades, energy poverty has captured a growing attention of researchers and policymakers due to its strong association with economic poverty and poor economic performance. This study uses a broad set of macro level indicators and makes the first attempt to measure energy poverty and its impact on economic growth of Pakistan over the period 1990 to 2017. In particular, our energy poverty indicator considers four main dimensions of energy poverty, namely, energy services, clean energy, energy governance and energy affordability. Our main results show that though the overall energy poverty has reduced in Pakistan during the selected sample period, the country shows an increasing dependence on polluted energy supply in order to meet its growing demand of energy. In second stage of the investigation, we test the neoclassical growth theory where we incorporate energy poverty along with human capital as source of economic growth. Our cointegration results reveal a strong relationship between energy poverty and economic growth that is also dynamically stable in short run. These strong negative linkages between energy poverty with economic growth for the sample economy complement the previous literature on the subject.

Machine learning offers advanced tools for efficient management of radio resources in modern wireless networks. In this study, we leverage a multi-agent deep reinforcement learning (DRL) approach, specifically the Parameterized Deep Q-Network (DQN), to address the challenging problem of power allocation and user association in massive multiple-input multiple-output (M-MIMO) communication networks. Our approach tackles a multi-objective optimization problem aiming to maximize network utility while meeting stringent quality of service requirements in M-MIMO networks. To address the non-convex and nonlinear nature of this problem, we introduce a novel multi-agent DQN framework. This framework defines a large action space, state space, and reward functions, enabling us to learn a near-optimal policy. Simulation results demonstrate the superiority of our Parameterized Deep DQN (PD-DQN) approach when compared to traditional DQN and RL methods. Specifically, we show that our approach outperforms traditional DQN methods in terms of convergence speed and final performance. Additionally, our approach shows 72.2 % and 108.5 % improvement over DQN methods and RL method respectively in handling large-scale multi-agent problems in M-MIMO networks.

Background: The associations between long-term exposure to particulate matters (PM) in residential ambiance and obesity are comparatively less elucidated among young adults. Methods: Using 2017 Community Health Survey data with aged 19−29 participants in 25 communities, Seoul, the relationship between obesity and long−term PM10 levels of living district was examined. We defined obesity as overweight (25≤BMI&lt;30) or obese (30≤BMI) using Body Mass Index (BMI) from self-reported anthropometric information. Analysis was conducted sampling weighted logistic regression models by fitting municipal PM10 levels according to individual residence periods with 10 years and more residing in a current municipality. Socio-demographic factors were adjusted over all models and age−specific effect was explored among aged 19–24 and 25–29. Results: Total study population are 3,655 [men 1,680 (46.0%) and aged 19–24 1,933 (52.9%)] individuals. Among the communities with greater level of PM10; 2001–2005, associations with obesity were increased for overall with residence period; 10 years ≤ [Odds ratio, OR 1.071, 95% Confidence interval (CI) 0.969–1.185], 15 years ≤ [OR 1.118, 95% CI 1.004–1.245], and 20 years ≤ [OR 1.156, 95% CI 1.032–1.294]. However, decreased associations were detected for PM10; 2006–2010, and age–specific effects were modified according to the residence period. Conclusions: Although currently PM10 levels are decreasing, higher levels of PM10 exposure at the residential area during the earlier life-time may contribute in increasing obesity among young adults.

Some of the recent large-scale national projects in South Korea are delayed or suspended due to belated responses to risk occurring on site. Currently, the Far East District (FED) project is being implemented to relocate the US Army bases from Yongsan to Pyeongtaek. Because of lack of experience and understanding about the characteristics of such a project, the deadline of taking over to the US Army Korea has been missed. This study identifies problems of each participant in the Yongsan Relocation Plan (YRP) of the US Army Korea with respect to construction project management and establishes a risk management strategy reflecting characteristics of FED project. To derive significant risk factors influencing YRP, various field data like weekly and monthly reports and other reports on construction condition are analyzed, and experts’ advices are collected and a survey is conducted. Mediators and latent variables are ultimately obtained. Furthermore, a structural equation model is used to both analyze and evaluate complex causal relations among many variables of YRP. The impact of risk factors on the schedule, quality and cost of the project is analyzed. In particular, the case of Site A is examined to see how the project is affected by those risk factors.

This study estimates the effects of double long memory and structural breaks on the persistence level of six major cryptocurrency markets. We apply the Bai and Perron’s structural break test, Inclán and Tiao’s iterated cumulative sum of squares (ICSS) algorithm, and the fractionally integrated generalized autoregressive conditional heteroscedasticity (FIGARCH) model with different distributions. The results show that long memory and structural breaks characterize the conditional volatility of cryptocurrency markets and confirm our hypothesis that ignoring structural breaks leads to an underestimation of the persistence of volatility modelling. The ARFIMA-FIGARCH model with structural breaks and a skewed Student–t distribution fits the cryptocurrency market’s price dynamics well.

Cause-Related Marketing (CRM) has emerged as a new concept that links CSR activities to marketing, enabling corporations to pursue both building company-consumer partnership and gaining sustainable mutual benefits that are elicited from the partnership. Among various cause-related marketing activities, on-line cause-related advertising is the most commonly used one. The purpose of this study is to examine the effects of on-line cause-related advertising and moderating role of ethical consumption propensity. In particular, this study intends to contribute to successful development of on-line cause-related advertising strategy by focusing on the relationship between the four factors: customers' perception of on-line cause-related advertising, brand-consumer relationship, brand attachment and loyalty. The results of this study are as follows: First, customers' perception of on-line cause-related advertising was related positively to consumer-brand- relationship. Second, brand-consumer relationship was related positively to brand attachment and customer loyalty. Third, brand attachment was related positively to customer loyalty. Furthermore, from the consumer’s psychological viewpoint, ethical consumption propensity had a significant moderating effect to between customers' perception of cause-related advertising and brand-consumer relationship as well as brand attachment. The results of this study may contribute to the existing literature as an new empirical attempt to examine the effect of the on-line cause-related advertising.

Mitochondria are highly dynamic organelles that continuously change their shape. Their main function is ATP production; however, they are additionally involved in a variety of cellular phenomena, such as apoptosis, cell cycle, proliferation, differentiation, reprogramming, and aging. The change in mitochondrial morphology is closely related to the functionality of mitochondria. Normal mitochondrial dynamics are critical for cellular function, embryonic development, and tissue formation. Thus, defect in proteins involved in mitochondrial dynamics that control mitochondrial fusion and fission can affect cellular differentiation, proliferation, cellular reprogramming, and aging. Here we review the processes and proteins involved in mitochondrial dynamics and its various associated cellular phenomena.

This study delves into the essential characteristics of the Metaverse and its impact on the real world. The Metaverse, a parallel universe composed of countless 3D virtual worlds, has become a hot topic in technology. With the development of advanced technologies such as Virtual Reality (VR), Augmented Reality (AR), blockchain, and Artificial Intelligence, the Metaverse is gradually changing people's lifestyles and work methods, expanding the boundaries of the digital economy. This study profoundly investigates the attributes of the Metaverse, such as asset digitization, application scenario-based, scope economy, industry universality, integrated innovation, and the platform ecosystem. Additionally, we propose a theoretical framework to aid in understanding and shaping this emerging field. We conducted a thorough study and analysis of a specific case, explored the key features of the Metaverse, unveiled the profound impact of Metaverse characteristics on social and economic development, and verified our theoretical framework with this case. This research provides new perspectives and methods for academic studies and offers robust support and guidance for practical applications and decision-making.

We still do not have satisfactory answers about the inflationary and accelerating expansions of the universe, the missing mass problem, and the origins of the four fundamental forces and the quantum phenomena. Here, we introduce a new model of matter and space and a postulate on a constant of motion, and then show that an equation of motion derived from the constant of motion could provide new understandings of the above problems. For example, we show that there is a natural inflation scenario and that the co-moving distance to the closest accelerating supernova is clearly given as $c/(\sqrt{3} H)$ ($\sim$8.1 billion ly). In addition, we show that, in a system including a proton and an electron, the equation of motion has eight acceleration terms, some of which are suspected to be responsible for the four fundamental forces and the galaxy rotation anomaly. From further discussion, we conjecture that in order to understand the gravitational and strong interactions and the quantum phenomena, it is necessary to consider the expansion of the universe. The lensing mass distribution is explained, based on another postulate on a method of representing superposition.

Low-complexity ultrasound systems are increasingly desired for wearable point-of-care ultra-sound and massive-channel ultrasound for 3-D matrix imaging. However, the system complexity is closely associated with the imaging capabilities, remaining as a challenge. To resolve this limitation, this study revisits the general structures of analog and digital beamformers and in-troduces a hybrid approach to implement efficient ultrasound systems. The suggested hybrid beamforming takes two stages, where the first analog stage partially beamforms M-channel RF signals to N sum-out data (M-to-N beamforming), and the second digital stage beamforms N partial sums to single final beamformed data (N-to-1 beamforming). Our approach was systematically designed and implemented, which was demonstrated with a customized 64-channel 1-D phased array using a tissue mimicking phantom. The demonstrated results indicate that the analog-digital hybrid beamforming can be applied to any kind of arrays for sophisticated 3-D imaging and tiny wearable ultrasound applications.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

This paper examines interlinkages and hedging opportunities between nine major cryptocurrencies for the period between 30 September 2015 and 4 June 2020, which notably includes the coronavirus disease 2019 (COVID-19) outbreak lasting from early 2020 through the end of the sample period. The results of dynamic conditional correlation (DCC) analysis using a minimum connectedness approach show a high degree of correlation between cryptocurrencies throughout the sample period. However, the correlations reach their minimum values during the COVID-19 pandemic, which indicates that cryptocurrencies acted as a hedge or safe haven during the stressful period of the COVID-19 pandemic. The weight of cryptocurrencies was significantly reduced and their hedging effectiveness varied greatly during the pandemic, which indicates that investors’ preferences changed during the COVID-19 period.

The proper hydrogenation of Hyper-coal (HPC) using 1, 2, 3, 4-tetrahydroquinoline (THQ) was able to decrease the oxygen content and adjust the molecular structure of HPC for preparing the spinnable pitch with high softening point (SP). The spinnable pitch prepared from the THQ-soluble (QS) fraction of HPC as a precursor consisted more naphthenic carbon groups than that prepared from the 1-methylnaphthalene (1-MN) soluble (MNS) fraction of HPC. The HPC-QS derived pitch showed excellent spinnability even the SP of 260°C, and the tensile strength of the resultant carbon fiber was up to 1350 MPa with a diameter around 8 µm by only heat treatment at 800°C for 5 min.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

Objectives: Essential thrombocythemia (ET) is a chronic myeloproliferative neoplasm characterized by elevated platelet counts and an increased risk of thrombotic events, including ischemic strokes. Methods: We conducted a retrospective analysis of data from consecutive ischemic stroke patients with ET between March 2014 and February 2023. Results: This case series describes the clinical presentation, radiological features, and management of five patients with ET-associated ischemic strokes, all harboring the JAK2 mutation. The diverse radiological findings suggest that both large and small vessel diseases may be influenced by the prothrombotic state induced by ET. A significant elevation in platelet count was observed to correlate with the emergence of new acute infarctions in some cases. Conclusions: The study highlights combined use of antiplatelet and cytoreductive therapy in preventing secondary stroke events in patients with ET and JAK2 mutations. The heterogeneity of stroke patterns in this population necessitates a comprehensive understanding of the underlying pathophysiological mechanisms and tailored therapeutic approaches.

Individual investors often struggle to predict stock prices due to the limitations imposed by the computational capacities of personal laptop Graphics Processing Units (GPUs) when running intensive deep learning models. This study proposes solving these GPU constraints by integrating deep learning models with technical analysis methods. This integration significantly reduces analysis time and equips individual investors with the ability to identify stocks that may yield potential gains or losses in an efficient manner. Thus, a comprehensive buy and sell algorithm, compatible with average laptop GPU performance, is introduced in the study. This algorithm offers a lightweight analysis method that emphasizes factors identified by technical analysis methods, thereby providing a more accessible and efficient approach for individual investors. To evaluate the efficacy of this approach, we analyzed the performance of eight deep learning models: LSTM (4 layers), CNN, BiLSTM (4 layers), CNN Attention, BiGRU CNN BiLSTM Attention, BiLSTM Attention CNN, CNN BiLSTM Attention, and CNN Attention BiLSTM. These models were used to predict stock prices for Samsung Electronics and Celltrion Healthcare. The CNN Attention BiLSTM model displayed superior performance among these models, with the lowest validation mean absolute error value. In addition, an experiment was conducted using WandB Sweep to determine the optimal hyperparameters for four individual hybrid models. These optimal parameters were then implemented in each model to validate their back-testing rate of return. The CNN Attention BiLSTM hybrid model emerged as the highest-performing model, achieving an approximate rate of return of 5 percent. Overall, this study offers valuable insights into the performance of various deep learning and hybrid models in predicting stock prices. These findings can assist individual investors in selecting appropriate models that align with their investment strategies, thereby increasing their likelihood of success in the stock market.

Interior permanent magnets motors are widely used in applications requiring high power den-sity and high efficiency due to their high torque generating capabilities. Recently, given the re-cent price fluctuations and unstable supply of rare-earth permanent magnets, alternative config-urations with reduced use of permanent magnets are being sought. Among the various candi-dates related to this, the consequent-pole type rotor structure can halve the number of perma-nent magnets used compared with conventional structures. However, in the no-load analysis, the waveform of the back electromotive force becomes asymmetric, generating a harmonic component. As a result, there is a disadvantage that the torque ripple increases. To overcome these shortcomings, we propose a novel rotor structure that applies a consequent-pole structure to an embedded permanent-magnet motor structure, wherein a number of permanent magnets are arranged in a flared structure to constitute a single polarity. In the proposed flared-structured magnet arrangement, it is possible to adjust the angle of the permanent magnet and the polar angle to mitigate the asymmetry of the back EMF waveform. The proposed struc-ture was optimized with a genetic algorithm and a prototype of the optimal model was con-structed and experimentally evaluated to verify its validity. Finally, the performance improve-ment and validity of the proposed structure were verified by comparing the analysis results of the optimal model with the experimental results.

We analyze the upside and downside risk connectedness among international stock markets. We characterize the connectedness among international stock returns using the Diebold and Yilmaz spillover index approach and compute the upside and downside value-at-risk. We document that the connectedness level of the downside risk is higher than that of the upside risk and that stock markets are more sensitive when the stock market declines. We also find that specific periods (e.g., the global financial crisis, the European debt crisis, and the COVID-19 turmoil) intensify the spillover effects across international stock markets. Our results demonstrate that the EU, Ger-many, and the US acted as net transmitters of dynamic connectedness; however, Japan (JP), China (CH), and India (IN) acted as net receivers of dynamic connectedness during the sample period. These findings provide significant new information to policymakers and market participants.

With the widespread Application of Virtual Reality (VR) in education, optimizing foreign language learning in VR has become a focal point of research. This paper introduces a comprehensive theoretical framework (VR-CCL) based on constructivism and cognitive load theory to enhance foreign language learning in VR. Through a literature review, we explore the applications of VR in education, foreign language learning theories, and prior works on technology-assisted language learning. We further detail the three main components of the VR-CCL framework and validate its effectiveness through two case studies: Duolingo VR and Rosetta Stone VR. Finally, we discuss the strengths and limitations of the framework and its implications for educators and developers.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

Additive manufacturing (AM) processes, including stereolithography (SL), can fabricate complex ceramic parts layer by layer using computer-aided design (CAD) models. A ceramic slurry with high solid loading is usually used in SL to fabricate the desired shape, which is further sintered to produce the final part. The traditional SL system utilizes a tank filled with printable material, known as a vat, which for ceramic slurry contributes several limitations and operational difficulties, and further renders it non-recyclable mainly due to its high viscosity and the fragility of the green state. In this study, we utilized a continuous film supply (CFS) printer integrated with a tape casting system using in-house-designed ceramic slurry to print standard prototype specimens. Various printing parameters, including viscosity, layer thickness control, and slurry recycling efficiency, were studied. In addition, post-processing optimizations of the prototype, characterizations, and the microhardness of sintered samples were studied to determine their properties and compare them with traditional methods. The effectiveness of slurry reusability was demonstrated by printing with original and recycled slurry to produce consistent densification of final parts. Post-processing was optimized to achieve a relative sinter density of 99.02% and microhardness of 12.59 GPa. This method provides new opportunities to realize dense complex ceramic features with final properties comparable to those produced by subtractive machining and traditional SL. Furthermore, slurry recycling helps to reduce the overall cost and material consumption.

Liver cirrhosis leads to hepatic dysfunction and life-threatening conditions. Though clinical efficacy of autologous bone marrow-drived mesenchymal stem cells (BM-MSC) transplantation in alcoholic cirrhosis (AC) was demonstrated, the relevant mechanism has not been elucidated. We aimed to identify predictive factors and gene/pathways for responders after autologous BM-MSC transplantation. Fifty-five patients with biopsy-proven AC underwent autologous BM-MSC transplantation. The characteristics of responders who showed improvement in fibrosis score (≥ 1) after transplantation were compared with those of non-responders. BM-MSCs were analyzed with cDNA microarrays to identify genes and pathways that were differentially expressed in responder after transplantation. Thirty-three patients (66%) were responders. In the multivariate analysis, initial high Laennec score (p=0.007, odds ratio 3.73) and performance of BM-MSC transplantation (p=0.033, odds ratio 5.75) were predictive factors for responder. Three genes (olfactory receptor 2L8, microRNA4520-2, and chloride intracellular channel protein 3) were upregulated in responders and 11 metabolic pathways (inositol phosphate, ATP-binding cassette transporters, protein kinase signaling, extracellular matrix-receptor interaction, endocytosis, phagosome, hematopoietic cell lineage, adipocytokine, peroxisome proliferator-activated receptor, fat digestion/absorption, and insulin resistance) were upregulated in non-responders (p<0.05). BM-MSC transplantation is warranted treatment for AC patients with high Laennec score. Cell-based therapy utilizing response-relating genes or pathway can be treatment candidate.

Regulated autophagy is involved in the repair of renal ischemia-reperfusion injury (IRI). ω3-Polyunsaturated fatty acids (ω3-PUFAs) show protective effects against various renal injuries. It was recently reported that ω3-PUFAs regulate autophagy. We assessed whether ω3-PUFAs attenuated IR-induced acute kidney injury (AKI) and evaluated associated mechanisms. C57Bl/6 background fat-1 mice and wild-type mice (wt) were divided into four groups: wt sham (n = 10), fat-1 sham (n = 10), wt IRI (reperfusion 35 min after clamping both the renal artery and vein; n = 15), and fat-1 IRI (n = 15). Kidneys and blood were harvested 24 h after IRI. Renal histological and molecular data were collected. The kidneys of fat-1 mice showed better renal cell survival, renal function, and pathological damage than those of wt mice after IRI. In addition, fat-1 mice showed less oxidative stress and autophagy impairment; greater amounts of LC3, Beclin-1, and Atg7; lower amounts of p62; and higher levels of renal cathepsin D and ATP6E than wt kidneys. They also showed more AMPK activation, which resulted in the inhibition of phosphorylation of the mammalian target of rapamycin (mTOR). Collectively, ω3-PUFAs in fat-1 mice contributed to AMPK mediated autophagy activation, leading to a renoprotective response.

This study examines the Willingness-To-Pay (WTP) of consumers and the determinants of eco-labeling for the organic cocoa powder produced in the Dong Nai UNESCO Biosphere Reserve (DNBR), Southern Vietnam. Eco-labels are designed according to Tiers of eco-labeling for biosphere reserves (BR) introduced by UNESCO include BR Destination (Tier 1), BR Quality Label (Tier 2), and Professional Certification Label (Tier 3). Questionnaires are delivered to 203 customers in the DNBR and nearby places, such as Dong Nai and HCMC. This study employs a hybrid approach using descriptive statistics, ANOVA test, and Partial Least Squares Structural Equation Model (PLS-SEM). The results indicate that gender and educational level have a positive effect on consumers' preferences. Customers are willing to pay more for cocoa powder with an eco-label than one with an organic label. Perceived food safety and product knowledge lower customers’ WTP, whereas agricultural environment and pricing concerns increase it. Tier 2 is suggested for labeling cocoa powder in the DNBR. The DNBR Management Board, together with the federal and provincial governments, should all follow a similar certification process. Increased eco-label awareness is crucial for the future of environmentally responsible shopping and responsible business practices.

In this study, we used statistical models to analyze nonlinear behavior links with atmospheric teleconnections between hydrometeorological variables and Indian Ocean Dipole (IOD) mode over the East Asia (EA) region. The analysis of atmospheric teleconnections was conducted using principal component analysis and singular spectrum analysis techniques. Moreover, the nonlinear lag-time correlations between climate indices and hydrological variables were calculated using mutual information (MI) techniques. The teleconnection-based nonlinear correlation coefficients (CCs) were higher than the linear CCs in each lag time. Additionally, we documented that the IOD has a direct influence on hydro-meteorological variables, such as precipitation within the Korean Peninsula (KP). Moreover, during the warm season (June to September) the variation of hydro-meteorological variables in the KP demonstrated significantly decreasing patterns during positive IOD years and they have neutral conditions during negative IOD years in comparison with long-term normal conditions. Finally, the revealed relationship between climate indices and hydro-meteorological variables and their possible changes will allow better understanding of stakeholder decision-making regarding to manage of freshwater management over the EA region. It can also provide useful data for long-range water resources prediction, to minimize hydrological uncertainties in a changing climate.

Currently, peptic ulcers are widely studied as an infectious disease caused by Helicobacter pylori primarily due to 3 supporting evidences, and this etiology may explain the other 3 observations, but cannot confront the challenges of the 15 major characteristics and the other 75 observations/phenomena of peptic ulcers. To address the challenges, a recently published Complex Causal Relationship with its accompanying methodologies was applied to analyze existing data. Peptic ulcers are identified as a psychosomatic disease triggered by psychological stress, where Helicobacter pylori plays a secondary role in only the late phase of ulceration. This new etiology elucidated all the 15 major characteristics and 81 observations/phenomena of peptic ulcers in a series of 6 articles. This sixth article focuses exclusively on the controversies surrounding the role of Helicobacter pylori in peptic ulcers. In-depth analyses find that all the 3 evidences supporting “peptic ulcers are an infectious disease caused by Helicobacter pylori” are deceiving, and 2 of the 3 explainable observations may have been misinterpreted. Meanwhile, the definitions of ‘etiological factor’ and ‘causality’ do not support ‘H. pylori infection is an etiological factor of peptic ulcers’, and existing literatures have presented a controversial view on the role of Helicobacter pylori in peptic ulcers. Interestingly, if “peptic ulcers are an infectious disease caused by Helicobacter pylori” is considered an illusion, all the characteristics of the disease, along with all the clinical, epidemiological, and laboratory observations/phenomena, can be fully understood. This illusion has misguided peptic ulcer research over the past 36 years with little progress in the field, and that may represent a widespread situation in modern medical research, resulting in a direct interference with the true understanding of disease. Evidently, keeping the concept “illusion” in mind may help remove a huge obstacle that impedes medical advance, thereby facilitating the in-depth study of disease.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

The widespread integration and growing dependence among currency, stock and commodity markets make these markets often very vulnerable to shocks and at risk of collapse at the same time. As a result, these trends threaten the sustainability of the entire financial system. In this study, we explore the spillovers and nonlinear dependences between the seven major foreign ex-change rates, crude oil and gold prices, a global stock price index, and oil and stock implied volatility indices as proxy variables for global risk factors by em-ploying directional spillover network approach. We also use multi-scale de-composition method and nonlinear causality test between these variables to capture multi-level relationships at short and long horizons. Major findings are summarized as follows. First, from the multi-scale decomposition analysis, we identify that Granger causality test results and the direction and strength of return spillovers change with the level of decomposition. Second, the results of nonlinear causality tests show variation in both the significance and direction of Granger causality relationships between the decomposed currency and other series at different timescales, especially for the decomposed oil, gold, and OVX series. Third, the measured directional spillover indices identify the EUR as the largest contributor of connectedness to the other series. The central role of the EUR is a net transmitter of connectedness to gold, oil, the GBP, JPY, and CHF.

According to statistics from the Food and Agriculture Organization, the world population will increase to about 91 million (Asia 51 million, Africa 19 million). A rise in the world’s population means an increased need for food. However, climate change has caused desertification and unpredictable weather, creating problems in the supply and demand of food. Sweet potato (Ipomoea batatas) is an alternative to solving the food problem, as it is one of the world’s most important food crops, especially in developing countries. The tuberous roots of sweet potato are usually used as staple food, animal feed, industrial material, or raw material for alcohol production. In the future, more variations of sweet potato will be needed for breeding this crop. Recently, molecular markers developed for sweet potato have demonstrated good potential for use in genetic selection. In this study, a cDNA library was constructed from the total RNA of sweet potato leaves. A total of 789 copies of the cDNA were cloned in Escherichia coli by employing the pGEM-T Easy vector. Sequencing was carried out by Solgent Co. (Korea). As many as 579 expressed sequence tag–simple sequence repeat (EST-SSR) markers were designed (73.38%) from the known cDNA nucleotide base sequences. The lengths of the developed EST-SSR markers ranged from 100 to 499 bp (average length 238 bp). Their motif sequence types were varied, with most being dinucleotides and pentanucleotides, and the most commonly found motifs were CAGAAT (29.0%) and TCT (2.8%). Based on these SSR-containing sequences, 619 pairs of high-quality SSR primers were designed using WebSat and Primer3web. The total number of primers designed was 144. Polymorphism was evident in 82 EST-SSR markers among 20 Korean sweet potato cultivars tested and in 90 EST-SSR markers in the two parents of a mapping population, Yeseumi and Annobeny. In this study, the hexaploid sweet potato (2n = 6x = 90) EST-SSR markers were developed in the absence of full-sequence data. Moreover, by acting as a molecular tag for particular traits, the EST-SSR marker can also simultaneously identify information about the corresponding gene. These EST-SSR markers will allow the molecular analysis of sweet potato to be done more efficiently. Thus, we can develop high-quality sweet potato while overcoming the challenges from climate change and other unfavorable conditions.

The effective Supervisory Control and Data Acquisition (SCADA) system can improve the reliability, safety and economic benefits of microgrid operation. In this research, the lower central controller and upper WEB monitoring system are connected by the SCADA system which is as the hub of microgrid intelligent monitoring platform. This system contains a set of specific functions programmed by Java as a middleware which can provide control and communication between the central controller and the upper monitoring system. The system realizes the real-time data acquisition and storage, the control instructions parsing and transmitting, the microgrid security and stability, the load balancing and resource recovery of the microgrid. All that functions have been tested and verified in the actual operation.

Head and neck squamous cell carcinoma (HNSCC) is a type of cancer that arises from the epithelium lining of the oral cavity, hypopharynx, oropharynx, and larynx. Despite advancement of the current treatment to HNSCC, such as surgery, chemotherapy, and radiotherapy, the overall survival rate of HNSCC remains poor due to late diagnosis and acquired resistance to treatment. Natural products have been extensively explored as a safer and more acceptable alternative to current treatments, with numerous studies displaying their potential against HNSCC. This review highlights preclinical studies in the past 5 years involving natural products against HNSCC and explores the signalling pathways altered by these products. This review also addresses challenges and future directions of the use of natural products as chemotherapeutic and chemoprevention agents against HNSCC.

The power converter is the significant device in a wind power system. Wind turbine will be shut down and off grid immediately with the occurrence of the IGBT module open-circuit fault of power converter, which will seriously impact the stability of grid and even threaten personal safety. However, in the existing diagnosis strategies of power converter, there are few single and double IGBT modules open-circuit fault diagnosis methods producing negative results including erroneous judgment, omissive judgment and low accuracy. In this paper, a novel method to diagnose the single and double IGBT modules open-circuit faults of the permanent magnet synchronous generator (PMSG) wind turbine grid-side converter (GSC) is proposed. Above all, collecting the three-phase current varying with wind speed of 22 failure states including a normal state of PMSG wind turbine GSC as the original signal data. Afterward, the original signal data are decomposed by using variational mode decomposition (VMD) to obtain the mode coefficient series, which are analyzed by the proposed method base on fault trend feature for extracting the trend feature vectors. Finally, the trend feature vectors are used as the input of deep belief network (DBN) for decision-making and obtaining the classification results. The simulation and experimental results show that the proposed method can diagnose the single and double IGBT modules open-circuit faults of GSC, and the accuracy is higher than the benchmark models.

Recently, various applications of indoor location-based services using Wi-Fi fingerprint data have been studied. However, since fingerprint data collected at a specific location does not have continuous information between signals and correlation information between signals, path data cannot exist in principle. Therefore, most indoor positioning technologies are based on predicting the position of a stationary positioner at a specific location based on signal data collected at a specific location in the indoor space. Due to the discontinuous nature of these signals, they are unable to account for user movement. Therefore, there is a need for techniques to improve the accuracy of indoor positioning in moving situations. This paper proposes a method for enriching all data points with relevant information to obtain improved indoor positioning results and an improved technique for generating movement path data. The proposed technique generates relevant information with continuity by expressing data points as Bounding Boxes (BB) and subsequently clustering them using grid cells. Through the proposed method, we represented and expanded the indoor location data, which consists of data points, as BB. However, data points represented by BB do not have any adjacency information with each other, and as a result, it is not possible to create a movement path between neighboring BB. To solve the problem, we used clustering, a machine learning technique that categorizes data points into groups, to group BBs. This was done by constructing a YOLO (You Only Look Once) grid cell that included all BBs and clustered them into grid cells that were divided into specific regions through the suggestion phase. The clustering results align with the indoor structure of the building, indicating that the data points have been appropriately clustered. BBs inside a grid cell are contained within a moveable area and have related information. We also generated association information between neighboring grid cells through the proposal technique, and then generated path information that can be traveled between grid cells. In this paper, we use the movement path information generated from a dataset as training data for machine learning, and through this, we propose an enhanced indoor positioning technology.

“A Picture is worth a thousand words”. Given an image, humans are able to deduce various cause-and-effect captions of past, current, and future events beyond the image. The task of visual commonsense generation aims at generating three cause-and-effect captions (1) what needed to happen before, (2) what is the current intent, and (3) what will happen after for a given image. However, such a task is challenging for machines owing to two limitations: existing approaches (1) directly utilize conventional vision-language transformers to learn relationships between input modalities, and (2) ignore relations among target cause-and-effect captions but consider each caption independently. We propose Cause-and-Effect BART (CE-BART) which is based on (1) Structured Graph Reasoner that captures intra- and inter-modality relationships among visual and textual representations, and (2) Cause-and-Effect Generator that generates cause-and-effect captions by considering the causal relations among inferences. We demonstrate the validity of CE-BART on VisualCOMET and AVSD benchmarks. CE-BART achieves SOTA performances on both benchmarks, while extensive ablation study and qualitative analysis demonstrate the performance gain and improved interpretability.

Osmotic demyelination syndrome (ODS) is an acute demyelinating disorder characterized by the loss of myelin in the center of the basis pons which is defined as central pontine myelinolysis (CPM) and demyelination process in locations outside the pons which is defined as extrapontine myelinolysis (EPM). ODS including CPM and EPM is mainly caused by the rapid correction of hyponatremia. However, there are several reports of ODS in medical condition such as malnutrition, alcoholism, liver transplantation, malignancy, sepsis, electrolyte imbalance including hypernatremia, hypokalemia, hypophosphatemia, and chronic illness. Rarely, ODS was reported in patients with hyperammonemia or hyperbilirubinemia without sodium fluctuations. The symptoms usually correspond to the lesion site and EPM precedes CPM. Because ODS may be irreversible, prevention is more important. Here, we report a case of ODS secondary to the hyperammonemia and hyperbilirubinemia, as it can have unfavorable prognosis.

We investigate the impact of air quality and weather on the equity returns of the Shenzhen Exchange. To capture the air quality and weather effects, we use dummy variables created by employing a moving average and moving standard deviation. The important results are as follows. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative influence on the equity returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative impacts on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the weather effect of the abnormal temperature on the stock returns is greater in severe bearish market. Whereas the effect of the air pollution on the stock returns is greater in the bullish market. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analyzing these effects in a very volatile emerging market such as the Shenzhen stock market.

We investigate the impact of air quality and weather on the stock market returns of the Shenzhen Exchange. To capture the air quality and weather effects, we apply dummy variables generated by applying a moving average and moving standard deviation. Our study provides several interesting results. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative effects on the Shenzhen stock returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative effects on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the more the Shenzhen stock returns drop, the greater the effect of the abnormal temperature is. Whereas, the more the Shenzhen stock returns increase, the greater the effect of the abnormal air quality is. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analysing these effects in a very volatile emerging market such as the Shenzhen stock market.

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

The purpose of this study was to select target nutrients to be included in the nutritional standards of school lunches in Korea. The dietary intake data of children and adolescents aged 6-17 years old from the Korea National Health and Nutrition Examination Survey Ⅵ were analyzed for eight groups based on gender and age (6-8, 9-11, 12-14, and 15-17 years old). First, the usual intake of the 3,091 subjects was estimated and assessed to identify nutrients with insufficient or excessive intake prevalence. Along with the nutrients identified by the assessment, the energy and nutrients prioritized in the meal planning procedure of the 2015 Dietary Reference Intakes for Koreans were the initial candidates: energy, the percentages of energy from carbohydrates, protein, and fat, vitamin A, riboflavin, niacin, vitamin C, calcium, phosphorus, sodium, and iron. Phosphorus was excluded due to little evidence of clinical symptoms caused by insufficient intake. Sodium was excluded because reliable data on added salt were not available among the school lunch recipes in Korea. Therefore, energy, the percentages of energy from carbohydrates, protein, and fat, vitamin A, riboflavin, niacin, vitamin C, calcium, and iron were selected to be included in the nutritional standards of school lunches in Korea.

Hydrogen energy is regarded as an auspicious future substitute to replace fossil fuels, because of its environmentally friendly characteristics and high energy density. In the pursuit of clean hydrogen production, there has been a significant focus on the advancement of effective electrocatalysts for the process of water splitting. Although noble metals like Pt, Ru, Pd and Ir are superb electrocatalysts for the hydrogen evolution reaction (HER), they have limitations for large-scale applications, mainly high cost and low abundance. As a result, non-precious transition metals have emerged as promising candidates to replace their more expensive counterparts in various applications. This review focuses on recently developed transition metal phosphides (TMPs) electrocatalysts for the HER in alkaline media due to the cooperative effect between the phosphorus and transition metals. Finally, we discuss the challenges of TMPs for HER.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

In this study, the dependence between Bitcoin (BTC) and economic policy uncertainty (EPU) of USA and China is estimated by applying latest methodology of quantile cross-spectral dependence. The findings indicate a positive return interdependence between BTC and EPU is high in short-term, and this dependence decreases as investment horizons increase from weekly to yearly. The information on above interdependence is also extracted by applying wavelet coherence analysis and the estimation results suggest that correlation between BTC and EPU is positive during short-term investment horizon. Furthermore, more diversification benefits of BTC can be obtained during USA-EPU as compared to China-EPU.