The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

IntroductionThe aim of this study is to describe the epidemiology of all COVID-19 patients in Vietnam and to describe the measures of disease control and prevention implemented. MethodsData were recovered from Wikipedia regarding the 2020 coronavirus pandemic in Vietnam. The period covered was from 23 January to 20 April 2020. Descriptive analysis was stratified by gender, age, country of origin, travel history, clinical symptoms and outcome. A survey of disease control and prevention measures was conducted at the Centre for Disease Control in the Thai Binh province, which is responsible for screening and isolating individuals at high risk of COVID-19. ResultsAs of 20 April 2020, Vietnam had recorded 268 confirmed COVID-19 patients. 55.2% were female. 67.9% were aged 20-49 years and 82.5% were Vietnamese. 60.4% of cases were imported from outside Vietnam. Other cases were acquired in Vietnam by individuals in close contact with imported cases. Only one patient who had not travelled had had no known contact with a confirmed case. 63.1% of patients were asymptomatic. 75.7% of patients were discharged. No deaths were recorded. The Thai Binh CDC surveyed a total of 2,203 persons at risk of COVID-19. 336 persons (15.2%) were isolated at hospitals and 1,411 (64.0%) in dedicated isolation facilities. 16.4% reported at least one respiratory symptom. No positive cases confirmed by RT-PCR have been reported in the Thai Binh province to date. ConclusionThe effect of the systematic screening and isolation strategy made it possible to limit local transmission in Vietnam. Vietnam needs to reinforce diagnostic capacities, prevention measures and provide the necessary epidemiological data on which to base interventions. The wider use of rapid serological tests is also advisable in order to be able to conduct extensive screening in the community.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

A highly crystallized monoclinic-scheelite type BiVO4 powders were successfully synthesized by solvothermal method. The as-synthesized BiVO4 powders were characterized by XRD, FE-SEM, Raman spectroscopy, UV-vis DRS spectroscopy and TA-PL. From the XRD data and Raman spectra, the monoclinic-scheelite phase BiVO4 sample can be obtained at higher solvothermal synthesis temperature more than 140 oC. The preparation conditions such as, the Bi/V molar ratio and synthesis temperature, have significantly effects on the morphologies of the BiVO4 samples. BVO2 sample shows the highest PL peak, which has the highest formation rate of OH radicals and the highest photocatalytic activity. This result suggests that the formation rate of OH radicals shows a good correlation with the photocatalytic activity.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

Wireless Sensor Networks are critical for modern applications ranging from environmental monitoring to smart city infrastructures. This research proposes a novel optimization learning and deployment strategy for Wireless Sensor Networks (WSNs) by 3D WUSN model is uniformly distributed M sensor nodes across diverse terrains, with clusters representing 20% of sensors, showcasing its ability to balance power consumption and extend network longevity, grounded in fuzzy clustering based protocol using the Fuzzy C-Means (FCM) method, called FCM-3DWUSN. Comparative analysis against established models including LEACH-C, K-Means and LEACH emphasized FCM-3DWUSN's outperformed performance, with average power consumption such as 134.990, 341.790, 143.895, and 192.984; respectively. The experimental result shows that FCM protocol in the 3D WUSN model can reduce energy consumption and improve the network lifetime to gather data and send the information.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

The objective of this study was to describe the overall pattern of morbidity and mortality of children seen at the Thai Binh Pediatric Hospital in Vietnam, with a focus on infectious diseases. A retrospective review of hospitalisation records was conducted from 1 January 2015 to 31 December 2019. Data were obtained from a total of 113,999 records. The median age of patients was 18 months, with 83.98% of patients aged <5 years. Infectious diseases accounted for 61.0% of all cases. The most prevalent diseases were lower respiratory tract infections (32.8%), followed by gastrointestinal infections (13.3%) and confirmed influenza (5.4%). Most infections were not microbiologically documented. A total of 81.4% patients received at least one antibiotic. Most patients (97.0%) were hospitalised for less than 15 days. Regarding outcomes, 87.8% patients were discharged home with a favourable outcome. 12.0% were transferred to the Vietnam National Children’s Hospital because their condition had worsened and 0.1% died. In total, infectious diseases accounted for 40.4% of deaths, followed by neonatal disorders (34.6%). Our data serves a basis for the identification of needs for diagnostic tools and for future evaluation of the effect of the targeted implementation of such facilities. Point-of-care tests, including real-time PCR assays to identify common pathogens should be implemented for more accurate diagnosis and more appropriate antibiotic use.

Alginate extraction is from seaweed, and lignin separation is from by-product corn (stalks and leaves). Alginate/lignin is a synthetic polymer rich in biological activity of great interest. Antioxidant activities of alginate/lignin were evaluated, such as total antioxidant activity, reducing power activity, DPPH free radical scavenging activity, and α – glucosidase inhibition activity. The test of anticancer activity was on four cell lines (Hep G2, fibroblast, MCF-7, and NCI H460). Determination of physical-chemistry characteristics of alginate/lignin was through FTIR, DSC, SEM_EDS, SEM_EDS mapping, XRD, XRF, and 1H-NMR. A study of acute toxicity of alginate/lignin was on Swiss albino mice. The results showed alginate/lignin possessed antioxidant activity such as total antioxidant activity, reducing power activity, especially, α – glucosidase inhibition activity, and no free radical scavenging activity. Alginate/lignin did not be typical in cancer cell lines. Alginate/lignin existed in a thermally stable regular spherical shape in the investigated thermal region. Some specific functional groups of alginate and lignin did not exist in alginate/lignin crystal. Elements such as C, O, Na, and S were popular in the alginate/lignin structure. LD0 and LD100 of alginate/lignin in mice were 3.91 g/kg and 9.77 g/kg, respectively. Alginate/lignin is the potential for application as pharmaceutical materials, functional foods, and supporting diabetes treatment.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

There are introduced two new steganalytic methods not depending on the statistics of the cover objects, namely side attacks stegosystems. The first one assumes that the plaintext, encrypted before embedding, is known by the attacker. In this case, the stegosystem’s detection is based on the calculation of mutual information between message and extracted encrypted data. For this calculation, a notion of the k-nearest neighbor distance is applied. The second method is applied to HUGO, one of the most efficient steganographic algorithms. In this case the stegosystem’s detection is based on a verification of the NIST tests to the extracted encrypted messages. Moreover, we show that the problem to find a submatrix of­ the embedding matrix determining a trellis code structure in the HUGO algorithm provides a search of the stegokey of the proposed stegosystem.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

Curcuma longa is only a rich source of curcumin (1) and its major analogues demethoxycurcumin (2) and bisdemethoxycurcumin (3) among the Curcuma species. The content ratio of these three curcumins in turmeric is depended on the varieties and growing environment. Recently, curcumin (1) has been reported as potential inhibitor of hepatic and enzymatic protein tyrosine phosphatase 1B (PTP1B) and its related disorders such as hypertriglyceridemia, hyperlipidemia and liver steatosis. Thus, we further purified curcumins (1–3) from C. longa and investigated their inhibitory effects against PTP1B and α-glucosidase enzymes. As the result, curcumins (1–3) exhibited potential PTP1B inhibition with IC50 values of 37.8 ± 1.4, 45.3 ± 0.7, and 72.6 ± 1.1 μM, respectively, and α-glucosidase inhibition with similar manner (IC50 values of 78.2 ± 0.2, 82.4 ± 0.6, and 90.6 ± 1.0 μM, respectively). These results reveal a key role of methoxylation in the variation of PTP1B and α-glucosidase inhibitory activity for these curcumins. In addition, density functional theory (DFT) was used accompanying with molecular docking (MD) to analyze the ligand stability and the interaction of curcumins (1–3) with PTP1B and glucoside hydrolase proteins. Assay-based results and the MD data obtained are highly correlation suggesting that the deterioration of the enzyme activity caused by the distortion of structural conformation of PTP1B and glucoside hydrolase may be related to the arrangement of amino acids in protein structure. This reported for the first time that inhibitory effects of curcumins (1–3) against PTP1B and glucoside hydrolase have been examined in vitro and in silico as well.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

This study investigates how the determinants including risk preference affect farmers’ decision to adopt SLM practices in upland areas of Vietnam. Empirical data collected through in-depth interviews with 200 farmers in Na Ri district, Bac Kan province were used. The factors affecting SLM adoption of farmers in Na Ri district were examined by the 2SLS or IV-Probit model. The estimated 2SLS regression indicated that there is a set of factors affecting SLM adoption, namely, relative risk aversion, farming experience, farm size, knowledge of SLM, membership in farmers’ organization, number of labors, and slope of farm land. Specifically, relative risk aversion had a negative effect on SLM practices adoption. The farmers who are less risk averse are more likely to adopt more SLM practices. This implies that reducing farmer’ risk exposure could promote SLM practices. This result is also helpful for policymakers to understand farmers’ behaviors and promote the diffusion of SLM practices across regions on a large scale.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

Protein import into the endoplasmic reticulum (ER) is the first step in the biogenesis of about 10,000 different soluble and membrane proteins in humans. It involves co- or post-translational targeting of precursor polypeptides to the ER and their subsequent membrane insertion or translocation. So far, three pathways for ER targeting of precursor polypeptides plus four pathways for ER targeting of mRNAs were described. Typically, these pathways deliver their substrates to the Sec61 polypeptide-conducting channel in the ER membrane. Next, the precursor polypeptides are inserted into the ER membrane or translocated into the ER lumen, which may involve auxiliary translocation components, such as the TRAP and Sec62/Sec63 complexes, or auxiliary membrane protein insertases, such as EMC and the TMCO1 complex. Recently, the PEX19/PEX3-dependent pathway, which has a well-known function in targeting and inserting various peroxisomal membrane proteins into pre-existent peroxisomal membranes, was also found to act in targeting and, putatively, inserting monotopic hairpin proteins into the ER. These either remain in the ER as resident ER membrane proteins or are pinched off from the ER as components of new lipid droplets. Therefore, the question arose if this pathway may play a more general role in ER protein targeting, i.e. represents a fourth pathway for ER targeting of precursor polypeptides. Thus, we addressed the client spectrum of the PEX19/PEX3-dependent pathway in both PEX3-depleted HeLa cells and PEX3-deficient Zellweger patient fibroblasts by an established approach, which involves label-free quantitative mass spectrometry of the total proteome of depleted or deficient cells and differential protein abundance analysis. The negatively affected proteins included twelve peroxisomal proteins and two hairpin proteins of the ER, thus confirming two previously identified classes of putative PEX19/PEX3-clients in human cells. Interestingly, fourteen collagen-related proteins with signal peptides or N-terminal transmembrane helices and belonging to the secretory pathway were also negatively affected by PEX3-deficiency, which may suggest compromised collagen biogenesis as a hitherto unknown contributor to organ failures in the respective Zellweger patients.

Flood frequency analysis at large scales, essential for the development of flood risk maps, is hindered by the uncertainty in outputs of process-based hydrological models and the scarcity of gauge flow data. We develop a Bayesian hierarchical model (BHM) based on the Generalized Extreme Value (GEV) distribution for regional flood frequency analysis at high resolution across North America. Our model leverages annual maximum flow data from ≈20000 gauged stations and a dataset of 130 static catchment-specific covariates to predict extreme flows at all catchments over the continent as well as their associated statistical uncertainty. Additionally, a modification is made to the data layer of the BHM to include daily gauge discharge data when available, which improves the precision of the discharge level estimates. We validated the model using a hold-out approach and found that its predictive power is very good for the GEV distribution location and scale parameters and improveable for the shape parameter, which is notoriously hard to estimate. The resulting discharge return levels yield satisfying agreement when compared with available design peak discharge from various government sources. Assessment of the covariates’ contributions to the model also informs on the most relevant underlying factors influencing flood-inducing peak flows. The key covariates in our model are temperature-related bioindicators, the catchment drainage area and geographical location.

Coastal erosion is threatening the infrastructures of coastal community at the Ma River mouth in Thanh Hoa province, Vietnam. When coastal erosion happens, people try to prevent it by emergency solutions like hard structures. However, this approach usually leads to more severe problem since the mechanism for coastal erosion is not investigated and understood properly. In this study the long-term configuration of Ma River mouth in Thanh Hoa Province, Central Vietnam has been investigated using Landsat imagery from 1987 to 2023. An analytical solution of one-line model for shoreline change was also employed to calculate the sand discharge from Ma River as well as the diffusion coefficient for sand transported along-shore by breaking waves. There was an asymmetric configuration of the Ma River mouth during the last 37 years. The sand supply from the Ma River is around 350,000 m3/year. This amount of sand is going mainly to the northern beach of the Ma River delta (from 55% to 75%). The asymmetric morphology of the Ma River mouth delta is the trigger for severe coastal erosion reported recently. This study provides a quick and easy method to investigate the morphological change of cuspate deltas where measured data is limited.

Wearable sensors for human physiological monitoring have attracted tremendous interest from researchers in recent years. However, most of the research was only done in simple trials without any significant analytical algorithms. This study provides a way of recognizing human motion by combining textile stretch sensors based on single-walled carbon nanotubes (SWCNTs) and spandex fabric (PET/SP) and machine learning algorithms in a realistic applications. In the study, the performance of the system will be evaluated by identification rate and accuracy of the motion standardized. This research aims to provide a realistic motion sensing wearable products without unnecessary heavy and uncomfortable electronic devices.

In the era of the post-quantum Internet of Things (IoT), the implementation of anti-quantum cryptographic algorithms in numerous terminals can successfully defend against prospective quantum computing assaults. Lattice-based cryptography can withstand quantum computing attacks, making it a viable substitute for the currently prevalent classical public-key cryptographic technique. Nevertheless, the algorithm’s significant time complexity will result in a substantial computational burden on the edge computing chip in the IoT terminal. The computation of polynomial multiplication is the most demanding task in lattice-based cryptographic algorithms. Therefore, the investigation into efficient methods for calculating polynomial multiplication is highly important. Quick number theory transformations (NTT) are a widely employed technique to accelerate polynomial multiplication. This study presents a hardware implementation of an efficient number theory transformation. We utilize a multi-level pipeline architecture in the design to accomplish parallel calculations and execute it on a low-profile Artix7-XC7A100T FPGA device. The performance evaluation results demonstrate that our implementation significantly enhances performance and reduces resource usage compared to other existing proposals on the same platform. We suggested NTT core can be implemented in edge computing chips to enhance computational speed due to its small and low-latency design. The experimental results show that the proposed design, which supports both NTT and inverse NTT, achieves 417-Megahertz and consumes only 541-LUTs on Artix-7 XC7A100T.

Resource conflicts represent a significant global challenge in regions abundant with natural re-sources. Modelling the myriad factors driving natural resource-based conflicts (NRBCs), spanning environmental, health, socio-economic, and political dimensions, is a complex endeavor exacer-bated by data scarcity. Furthermore, existing quantitative studies often focus solely on large-scale conflicts. This article introduces a novel algorithm, the Spatially Explicit Fuzzy Logic-Adapted Model for Conflict Management (SEFLAME-CM), which integrates the local knowledge of stakeholders into spatial decision-making technologies to support sustainable peace efforts. The results are validated with spatial multi-criteria evaluation (SMCE) using spatial statistics. The Moran’s I scatter plots for the overall conflicts reveal significant values of 0.99 and 0.98 for both the SEFLAME-CM and SMCE, respectively, with significant spatial autocorrelation. While there re-mains room for improvement in enhancing the model's quality, SEFLAME-CM demonstrates its capacity to transparently model complex real-world problems. The findings underscore the im-perative for a holistic approach to addressing environmental degradation, socio-economic, and political drivers of resource conflicts at the community level. Our paper demonstrates the signif-icance of spatial information technologies and knowledge exchange between experts and local stakeholders in effectively managing resource conflicts. These insights should inform national policies and international interventions, ensuring that the complex underlying issues are ad-dressed while prioritizing the knowledge and needs of affected communities.

Hydraulic fracturing has enabled production from unconventional reservoirs in the U.S., but production rates often decline sharply, limiting recovery factors to under 10%. This study optimizes the CO2 huff-n-puff process for multistage-fractured horizontal wells in Wolfcamp A formation in the Delaware Basin. The potential for enhanced oil recovery and CO2 sequestration simultaneously was addressed using a coupled geomechanics-reservoir simulation. Geomechanical properties were derived from a 1D mechanical earth model and integrated into reservoir simulation to replicate hydraulic fracture geometries. The fracture model was validated using a robust production history matching. Fluid phase behavior analysis refined the equation of state, and 1D slim tube simulations determined a minimum miscibility pressure of 4300 psi for CO2 injection. After the primary production phase, various CO2 injection rates were tested from 1 to 25 MMSCFD/well, resulting in incremental oil recovery ranging from 6.3% to 69.3%. Different injection, soaking, and production cycles were analyzed to determine the ideal operating condition. The optimal scenario improved cumulative oil recovery by 68.8% while keeping the highest CO2 storage efficiency. The simulation approach proposed by this study provides a systematic workflow for evaluating and optimizing CO2 huff-n-puff in hydraulically fractured wells, enhancing the recovery factor of unconventional reservoirs.

Tidal inlets with attached sand spits are a very common coastal morphology. Since the evolution of the sand spits along the coastline have greatly affected on the social-economic development of local coastal areas. However, previous studies mainly focused on the sand spits which are usually in the scales of hundred meters in width. Therefore, in this study, morphological change of a smaller and unexplored sand spit located in the west coast of Phu Quoc Island, will be investigated. It was found that there is a seasonal variation in the evolution of the sand spit at Song Tranh Inlet. The Longshore sediment transport rates (LSTR) along the spit are in the order from 104 to 105 m3/year. LSTRs of fourteen inlets in the literature were reviewed and the LSTRs at Song Tranh Inlet are higher than half of the LSTRs along the fourteen reviewed inlets. This study aims at contrib-uting to the growing literature on sand spit morphological changes as well as the sustainable coastal management for Phu Quoc Island which is well known as the Pearl Island of Vietnam.

Enteric protozoan pathogenic infections significantly contribute to the global burden of gastrointestinal illnesses. Their occurrence is considerable within remote and indigenous communities and regions due to reduced access to clean water and adequate sanitation. The robustness of these pathogens means requirement of harsh treatment methods such as medicinal drugs or antibiotics. However, such treatments impact the gut microbiome, and create dysbiosis, often leading to opportunistic pathogens, anti-microbial resistance, or functional gastrointestinal disorders (FGIDs) such as irritable bowel syndrome (IBS). Recent studies have shown that these impacts do not remain confined to gut, and are reflected across the gut-brain, gut-liver, and gut-lung axes, among others. Therefore, apart from the medicinal treatment, nutritional supplementation is also a key aspect of providing the recovery from this dysbiosis. Future proteins, prebiotics, probiotics, synbiotics, and food formulations offer a good solution to remedy this dysbiosis. Furthermore, the nutritional supplementation also helps to build a resilience against the opportunistic pathogens and potential future infections and disorders that may arise due to the dysbiosis. Systems biology techniques have shown to be highly effective tools to understand the biochemistry of these processes. Systems biology techniques characterises the fundamental host-pathogen interaction biochemical pathways, at various infection and recovery stages. This same mechanism also allows to track the impact of abovementioned treatment methods of gut microbiome remediation. This manuscript is organised in sections delving into system biology approaches and upcoming developments to understand (1) Infection mechanism and current global status; (2) Cross-organ impacts of dysbiosis, particularly within gut-liver and gut-lung axes; (3) Nutritional interventions. It highlights the impact of antimicrobial resistance (AMR) and Multi-drug resistance (MDR) from a perspective of protozoal infections. It also highlights the role of nutritional interventions to add resilience against the chronic problems caused by these phenomena.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.

Diseases pose a significant and pressing concern for the sustainable development of the aquaculture sector, particularly as their impact continues to grow due to climatic shifts such as rising water temperatures. While various approaches, ranging from biosecurity measures to vaccines, have been devised to combat infectious diseases, their efficacy is disease- and species-specific and contingent upon a multitude of factors. The field of genetics and genomics offer effective tools to control and prevent disease outbreaks in aquatic animal species. In this study, we present the key findings from our recent research, focusing on the genetic resistance to three specific diseases: White Spot Syndrome Virus WSSV) in white shrimp, Bacterial Necrotic Pancreatitis (BNP) in striped catfish and skin fluke (a parasitic ailment) in yellowtail kingfish. Our investigations reveal that all three species possess substantial heritable genetic components for disease resistant traits, indicating their potential responsiveness to artificial selection in genetic improvement programs tailored to combat these diseases. Also, we observed a high genetic association between disease traits and survival rates. Through selective breeding aimed at enhancing resistance to these pathogens, we achieved substantial genetic gains, averaging 10% per generation. These selection programs also contributed positively to the overall production performance and productivity of these species. Although the effects of selection on immunological traits or immune responses were not significant in white shrimp, they yielded favourable results in striped catfish. Furthermore, our genomic analyses, including shallow genome sequencing of pedigreed populations, enriched our understanding of the genomic architecture underlying disease resistance traits. These traits are primarily governed by a polygenic nature, with numerous genes or genetic variants, each with small effects. Leveraging a range of advanced statistical methods, from mixed models to machine and deep learning, we developed prediction models that demonstrated moderate to high levels of accuracy in forecasting these disease-related traits. In addition to genomics, our RNA-seq experiments identified several genes that undergo upregulation in response to infection or viral loads within the populations. Preliminary microbiome data, while offering limited predictive accuracy for disease traits in one of our studied species, underscore the potential for combining such data with genome sequence information to enhance predictive power for disease traits in our populations. Lastly, this paper briefly discusses the roles of precision agriculture systems, AI algorithms, and outlines the path for future research to expedite the development of disease-resistant genetic lines tailored to our target species. In conclusion, our study underscores the critical role of genetics and genomics in fortifying the aquaculture sector against the threats posed by diseases, paving the way for more sustainable and resilient aquaculture development.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

With Internet of Things (IoT) gaining presence throughout different industries a lot of new technologies have been introduced to support this undertaking. Implications on one such technology, wireless systems allowed for the use of different communication methods to achieve the goal of transferring data reliably, with more cost efficiency and over longer distances. Anywhere from a single house with only a few IoT devices such as a smart light bulb or a smart thermostat connected to the network, all the way to a complex system that can control power grids throughout countries, IoT has been becoming a necessity in everyday lives. This paper presents an overview of the devices, systems and wireless technologies used in different IoT architectures (Healthcare, Vehicular Networks, Mining, Learning, Energy, Smart Cities, Behaviors and Decision Making), their upbringings and challenges to this date and some foreseen in the future.

Due to its application as an anti-cancer drug, pazopanib (1) has attracted the interest of many researchers and several studies on pazopanib synthesis have been reported over the years. This paper provides a novel route for synthesizing N,2,3-trimethyl-2H-indazol-6-amine (5) which is a crucial building block in the synthesis of pazopanib from 3-methyl-6-nitro-1H-indazole (6). By alternating between the reduction and two methylation steps compound 5 was obtained in comparable yield (55.0%) to what has been reported (54%). Noteworthy, the last step of N2-methylation also yielded N,N,2,3-tetramethyl-2H-indazol-6-amine (5’) as a new compound ever reported. Furthermore, the data presented in this paper can serve as instrumental for future research aimed at further refining the synthesis process of pazopanib.

Vietnam is the second largest coffee producer in the world, mostly from the Central Highlands region where water has been becoming a scarce resource. Since 2014, drought has been strongly affecting Central Highlands’ agriculture, particularly coffee production. The drought leads to changes in flowering, ripening and thus harvesting times of coffee. Coffee productivity has reduced about 50 percent. Ultimately, coffee quantity and quality is jeopardized which endangers coffee farmers who occupy 90 per cent of population and their livelihoods mainly rely on coffee. Most of coffee farmers have had to develop alternative strategies to respond to the drought. Based on quantitative and qualitative data collected from 50 coffee households in a community in the Central Highlands, this research has indicated that farmers had to find the ways to adapt as well as to cope with drought. The ways of adaptation and coping were diverse, including short, medium and long-term plans. To strengthen the adaptation and coping strategies of farmers with drought in the short term, it is recommended that authorities provide more technical and financial support to farmers. Furthermore, longer term strategies need to focus on land use planning, investment in irrigation schemes, and consolidated afforestation schemes in appropriate areas.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

An HFMD outbreak spread over the city of Hải Phòng from Summer 2011 to Autumn 2012. This epidemic was chosen because it was the very first HFMD epidemic in North Vietnam, eliminating thus interferences with previous outbreaks. This epidemic displayed 3 separate waves. A complete dataset was collected for more than 9500 patients during this period, which enabled us to analyze this epidemic at different scales. Access to the healthcare system was crucial during this period, with a reorganization of the system in February-March 2012. An analysis at commune level enables us to track the epidemic along certain communication routes. The three-waves structure reveals a wide disparity at district level. We develop a mathematical model showing high accuracy at the adjustment of data for both the total number of cases and for the number of cases per week. As a consequence, the model was able to accurately determine the dates of beginning and end of each wave and to show that they overlapped. Using mathematical functions associated with this model, it was possible to calculate the probability for a patient to belong to a specific wave.

Livestock farming is a major source of greenhouse gas and ammonia emissions. In this study, we estimate methane, nitrous oxide and ammonia emission from livestock sector in the Red River Delta region from 2000 to 2015 and projection to 2030 using IPCC 2006 methodologies with the integration of local emission factors and provincial statistic livestock database. Methane, nitrous oxide and ammonia emissions in 2030 are estimated at 132 kt, 8.3 kt and 34.2 kt, respectively. Total global warming potential is 9.7 MtCO_2eq in 2030, accounts for 33% greenhouse gas emissions from livestock in Vietnam. Pig farming is responsible for half of both greenhouse gases and ammonia emissions in the studied region. Other major livestock for greenhouse gas emission is cattle and for ammonia emission is poultry. Hanoi contributes for the largest emissions in the region in 2015 but will be caught up and surpassed by other provinces in 2030.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

Antibiotic-free approaches are more important than ever to deal with the rapidly growing problem of antibiotic resistance. The blue light 460nm (BL460nm) has been shown to effectively attenuate Staphylococcus aureus to chemical and physical agents through photolysis of the bacterial virulence factor Staphyloxanthin. However, the phototherapy using BL640nm has yet to be investigated in detail for its safety in eradicating Staphylococcus aureus in vitro and in vivo. In this study, we used a LED source producing a continuous wavelength of 460 nm along with hydrogen peroxide to treat S. aureus in culturing conditions and a wound abrasion mouse model. The results proved the safety of the combined therapy when it did not modify the bacterial virulence factors or the susceptibility to the widely used antibiotics. In addition, the experimental results on the mouse skin infection model also showed that the combined therapy is safe to apply to mouse skin and that it did not cause adverse skin irritation. Furthermore, the therapy can help Staphylococcus aureus-infected wounds heal with efficacy comparable to the topical antibiotic Fucidin. The above results suggest that the combination therapy of 460nm blue light and hydrogen peroxide can be safely used as an alternative to or adjunct to antibiotics in treating S. aureus-infected wounds.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

This study aimed to characterize the long non-coding RNA (lncRNA) expression in the bovine mammary gland and to infer their functions in dietary response to 5% linseed oil (LSO) or 5% safflower oil (SFO). Twelve cows (six per treatment) in mid lactation were fed a control diet for 28 days followed by a treatment period (control diet supplemented with 5% LSO or 5% SFO) of 28 days. Mammary gland biopsies were collected from each animal on day-14 (D-14, control period), D+7 (early treatment period) and D+28 (late treatment period) and were subjected to RNA-Sequencing and subsequent bioinformatics analyses. Functional enrichment of lncRNA was performed via potential cis regulated target genes located within 50 Kb flanking regions of lncRNAs and having expression correlation of >0.7 with mRNAs. A total of 4955 lncRNAs (325 known and 4630 novel) were identified which potentially cis targeted 59 and 494 genes in LSO and SFO treatments, respectively. Enrichments of cis target genes of lncRNAs indicated potential roles of lncRNAs in immune function, nucleic acid metabolism and cell membrane organization processes as well as involvement in Notch, cAMP and TGF-β signaling pathways. Thirty-two and 21 lncRNAs were differentially expressed (DE) in LSO and SFO treatments, respectively. Six genes (KCNF1, STARD13, BCL6, NXPE2, HHIPL2 and MMD) were identified as potential cis target genes of six DE lncRNAs. In conclusion, this study indicated potential roles for lncRNAs in mammary gland immune functions and development and provided potential candidate genes and pathways via which lncRNAs can function in diet responses.

A simple and sensitive liquid chromatography-tandem mass spectrometry (LC– MS/MS) method has been developed for the simultaneous determination of atorvastatin (ATOR), ezetimibe (EZM) and their three metabolites including o-hydroxyl atorvastatin (o-OH ATOR), p-hydroxyl atorvastatin (p-OH ATOR), and ezetimibe-glucuronide (EZM-G) in human plasma using benzyl paraben (BP) as internal standard (IS). The analytes and IS were ionized using ESI positive ion mode (ATOR, o-OH ATOR, and p-OH ATOR), ESI negative ion mode (EZM, EZM-G, and BP), and operated in multiple reaction monitoring (MRM) mode. They were next extracted by salting-out assisted liquid–liquid extraction with acetonitrile, and then analyzed by liquid chromatography on a reversed-phase chromatographic column (50 mm × 4.6 mm; 3.5 µm), using a mixture of ac-etonitrile and an acetic acid solution (0.5%) as the mobile phase, showing high extraction effi-ciency (>70%), and a minimized matrix effect. The method was satisfactorily validated, and showed excellent linearity over wide concentration ranges of 0.06–15 ng/mL, 0.6–150 ng/mL, 0.4–100 ng/mL, 0.12–30 ng/mL, and 0.05–3 ng/mL for EZM, EZM-G, ATOR, o-OH ATOR, and p-OH ATOR, respectively.

Lipid nanoparticles have an interesting part of drug delivery system. In this study, the modification of the convention nano-lipid based soybean lecithin was demonstrated. Ginger oil derived Zingiber officinale was used along with lecithin, cholesterol and span 80 to fabricate nano-lipid (GL nano-lipid) using thin-film method. Through TEM and confocal microscope, GL nano-lipid exposes the liposome- like morphology. The average size of the resultant nanoparticles was 249.1nm with monodistribution (PDI= 0.021). The ζ-potential of GL nano-lipid was negative as similar to as prepared nano-lipid based lecithin. GL nano-lipid express the highly stable over 60 days of storage at room temperature in term of size, ζ-potential. A shift of pH value from alkaline to acid was detected in lecithin nano-lipid, while with the incorporation of ginger oil, pH value of nano-lipid dispersion was around 7.0. Furthermore, due to the rich of shogaol-6 and other active compounds in ginger oil, the GL nano-lipid is endowed with intrinsic antibacterial feature. In addition, the sulforhodamine B (SRB) assay and live/dead imaging revealed the excellent biocompatibility of GL nano-lipid. Notably, GL nano-lipid was capable to carry the hydrophobic agents as curcumin and perform a pH-dependent release profile. A subsequent characterization are a suitable potential for drug delivery system.

AI integration is becoming more important in today’s world and could potentially be very useful in the life sciences and biotechnology. This study evaluates the effectiveness of AI systems in teaching molecular cloning techniques to newcomers in molecular biology, focusing on a comparison between Gemini Advanced (powered by Gemini Ultra 1.0) and ChatGPT (GPT-4o). Molecular or DNA cloning is a lab technique for creating multiple copies of a specific DNA segment. It involves isolating the DNA fragment, inserting it into a vector, and introducing it into a host cell, typically bacteria, which then generates numerous copies of the DNA. This essential technique underpins genetic engineering, allowing for gene study, protein expression, and the creation of genetically modified organisms. The primary objective of this study was to assess whether individuals with limited laboratory experience could effectively acquire a specific molecular biology skill set solely through an AI system, rather than relying on the more traditional ‘learning by shadowing’ approach. Participants with limited lab experience completed these tasks using both Gemini and GPT-4o, and evaluated on quality of instructions, conciseness, scientific accuracy, and user satisfaction. Results indicated that both AI systems demonstrated strengths in delivering clear and comprehensive instructions, but in different ways. Gemini, although more interactive with images and diagrams lacked directness and had a harder time keeping past steps in its “memory”. On the other hand, GPT-4o was much more direct and concise in the steps listed and had more accurate results akin to what is performed in the lab. This study underscores the potential of AI-driven tools to simplify complex biotechnological procedures, making them accessible for learners at all levels.

Accurate pathogenic detection in wastewater is critical for safeguarding public health and the environment. However, the presence of free nucleic acids in wastewater samples poses significant challenges to molecular detection accuracy. This comprehensive review explores the current status and future potential of pretreatment methods to remove free nucleic acids from wastewater samples. The study contributes a comprehensive analysis of the mechanisms, strengths, and limitations of various pretreatment approaches, including physical, chemical, and enzymatic processes. The effect of various factors on the removal efficiency of these pretreatment methods is also discussed. This review enhances our comprehension of pretreatment techniques and their vital role in achieving precise pathogenic detection in complex wastewater matrices. Furthermore, it outlines future perspectives and developments for improving the speed and effectiveness of pathogenic detection, contributing significantly to disease surveillance, early warning systems, and environmental protection.

The Soil and Water Assessment Tool (SWAT) is one of the most widely used hydrologic models. SWAT has been undergoing constant changes since its development. However, compartment review and testing of SWAT are comparably limited, especially the flood routing functions. In this study, the daily flood routing subroutines of different SWAT versions were reviewed and tested using a well observed segment of the Weser river located in Germany. Results show several problems with the flood routing subroutines of SWAT. The variable storage subroutine of SWAT (revision 664) does not transform the flood wave. Unphysical results could be obtained with the variable storage routing of SWAT (revision 528). The Muskingum subroutine of SWAT (revisions 664 and 528) overestimates channel evaporation (resulting in a bias of 14\% to 19% in streamflow) and underestimates transmission losses. Simulated results show that the timing and shape of the flood wave could be improved with a corrected Muskingum subroutine. Based on the results of this study, we suggest the SWAT user community to review their existing SWAT models to see how the aforementioned issues will affect their methods, findings and conclusions.

Generative artificial intelligence (GenAI) has been developing with many incredible achievements like ChatGPT and Bard. Deep generative model (DGM) is a branch of GenAI, which is preeminent in generating raster data such as image and sound due to strong points of deep neural network (DNN) in inference and recognition. The built-in inference mechanism of DNN, which simulates and aims to synaptic plasticity of human neuron network, fosters generation ability of DGM which produces surprised results with support of statistical flexibility. Two popular approaches in DGM are Variational Autoencoders (VAE) and Generative Adversarial Network (GAN). Both VAE and GAN have their own strong points although they share and imply underline theory of statistics as well as incredible complex via hidden layers of DNN when DNN becomes effective encoding/decoding functions without concrete specifications. In this research, VAE and GAN is unified into a consistent and consolidated model called Adversarial Variational Autoencoders (AVA) in which VAE and GAN complement each other, for instance, VAE is good at generator by encoding data via excellent ideology of Kullback-Leibler divergence and GAN is a significantly important method to assess reliability of data which is realistic or fake. In other words, AVA aims to improve accuracy of generative models, besides AVA extends function of simple generative models. In methodology this research focuses on combination of applied mathematical concepts and skillful techniques of computer programming in order to implement and solve complicated problems as simply as possible.

Expectation maximization (EM) algorithm is a powerful mathematical tool for estimating statistical parameter when data sample contains hidden part and observed part. EM is applied to learn finite mixture model in which the whole distribution of observed variable is average sum of partial distributions. Coverage ratio of every partial distribution is specified by the probability of hidden variable. An application of mixture model is soft clustering in which cluster is modeled by hidden variable whereas each data point can be assigned to more than one cluster and degree of such assignment is represented by the probability of hidden variable. However, such probability in traditional mixture model is simplified as a parameter, which can cause loss of valuable information. Therefore, in this research I propose a so-called conditional mixture model (CMM) in which the probability of hidden variable is modeled as a full probabilistic density function (PDF) that owns individual parameter. CMM aims to extend mixture model. I also propose an application of CMM which is called adaptive regressive model (ARM). Traditional regression model is effective when data sample is scattered equally. If data points are grouped into clusters, regression model tries to learn a unified regression function which goes through all data points. Obviously, such unified function is not effective to evaluate response variable based on grouped data points. The concept “adaptive” of ARM means that ARM solves the ineffectiveness problem by selecting the best cluster of data points firstly and then evaluating response variable within such best cluster. In order words, ARM reduces estimation space of regression model so as to gain high accuracy in calculation.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

2-Methylquinazolin-4(3H)-one was prepared by reaction of anthranilic acid, acetic anhydride and ammonium acetate. The reaction of 2-methylquinazolin-4(3H)-one with N-aryl-2-chloroacetamides in acetone in the presence of potassium carbonate gave nine N-aryl-2-(2-methyl-4-oxoquinazolin-3(4H)-yl)acetamide compounds. The structures of these compounds were elucidated on the basis of their IR, 1H-NMR, 13C-NMR and HR-MS spectral data. These synthesized compounds containing the 2-methyl-3,4-dihydroquinazolin-4-one moiety exhibited excellent activity against Aedes aegypti mosquito larvae with LC50 values in the range of 2.085-4.201 μg/mL after 72 h exposure. Interestingly, these compounds did not exhibit toxicity to the non-target organism Diplonychus rusticus. In silico molecular docking revealed acetylcholine binding protein (AChBP) and acetylcholinesterase (AChE) to be potential molecular targets. These data indicated the larvicidal potential and environmental friendliness of these N-aryl-2-(2-methyl-4-oxoquinazolin-3(4H)-yl)acetamide derivatives.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Dyadic data which is also called co-occurrence data (COD) contains co-occurrences of objects. Searching for statistical models to represent dyadic data is necessary. Fortunately, finite mixture model is a solid statistical model to learn and make inference on dyadic data because mixture model is built smoothly and reliably by expectation maximization (EM) algorithm which is suitable to inherent spareness of dyadic data. This research summarizes mixture models for dyadic data. When each co-occurrence in dyadic data is associated with a value, there are many unaccomplished values because a lot of co-occurrences are inexistent. In this research, these unaccomplished values are estimated as mean (expectation) of random variable given partial probabilistic distributions inside dyadic mixture model.

The purpose of this study is to elucidate the factors influencing the voluntary adoption of IFRS by examining, analyzing, and synthesizing findings from empirical studies conducted worldwide. The research scrutinizes 185 relevant studies on the voluntary adoption of IFRS published before August 2023. Our assessment reveals that, in prior research, the factors influencing the voluntary adoption of IFRS are categorized into seven main factors, including corporate operations, capital structure, ownership structure, internationalization, financial performance, corporate governance, and several other factors. These studies employ various methodologies, including data surveys, and cross-sectional data, to estimate the relationships between these factors and the voluntary adoption of IFRS. In addition to providing an evaluation of the research in this field, this study can serve as a framework for future researchers to link and compare the results of different studies. We anticipate that this research will be beneficial for future scholars interested in the factors influencing the voluntary adoption of IFRS. Furthermore, the study proposes essential guidance for future research considerations.

We report here the synthesis of uniform nanospheres-like silver nanoparticles (AgNPs, 5-10 nm) and the dumbbell-like Fe3O4-Ag hybrid nanoparticles (FeAgNPs, 8-16 nm) by the use of seeding growth method in the presence of oleic acid (OA)/oleylamine (OLA) as surfactants. The antibacterial activity of pure nanoparticles and nanocomposites by monitoring the bacterial lag–log growth has been investigated. The electron transfer from AgNPs to Fe3O4NPs which enhances the biological of silver nanoparticles has been proven by nanoscale Raman spectroscopy. The lamellae structure in the spherulite of FeAgNPs/PE nanocomposites seems play the key role to the antibacterial activity of nanocomposites, which has been proven by nanoscale AFM-IR. An atomic force microscopy coupled with nanoscale infrared microscopy (AFM-IR) is use to highlight the distribution of nanoparticles on the surface of nanocomposite at the nanoscale. The presence of FeAgNPs in PE nanocomposites has a better antibacterial activity than that reinforced by AgNPs due to the faster Ag+ release rate from the Fe3O4-Ag hybrid nanoparticles and the ionization of AgNPs in hybrid nanostructure.

MicroRNAs (miRNAs) are small endogenous RNAs that regulate gene expression post-transcriptionally by targeting either the 3′ untranslated or coding regions of genes. They have been reported to play key roles in a wide range of biological processes. The recent remarkable developments of transcriptomics technologies, especially next-generation sequencing technologies and advanced bioinformatics tools, allow more in-depth exploration of messenger RNAs (mRNAs) and non-coding RNAs (ncRNAs) including miRNAs. These technologies have offered great opportunities for a deeper exploration of miRNA involvement in farm animal diseases, as well as livestock productivity and welfare. In this review, we provide an overview of the current knowledge of miRNA roles in farm animal diseases with a particular focus on diseases of economic importance. In addition, we discuss the steps and future perspectives of using miRNAs as biomarkers and molecular therapy for livestock disease management as well as the challenges and opportunities for understanding the regulatory mechanisms of miRNAs related to disease pathogenesis.

(1) Background: This study aimed to evaluate the role of cervical pessary for preventing preterm birth in singleton pregnant women with a cervical length (CL) ≤25 mm and a uterocervical angle (UCA) ≥95o and ≥105o. (2) Methods: A quasi-experimental study was conducted on 225 singleton pregnant women with a gestational age of 16+o-23+6 weeks and transvaginal ultrasound CL measurements ≤25 mm, whose pregnancy was man-aged at the Haiphong Hospital of Obstetrics and Gynecology, Vietnam, from September 2020 to September 2022. Participants were allocated into two groups: prophylactic treatment with progesterone (123 pregnant women) and combined with a cervical pessary (102 pregnant women). The UCAs measured via transvaginal ultrasound by a single sonographer were divided into groups with UCA measurements ≥95o and ≥105o. The gestational age at birth was classified into full-term and preterm <37 weeks and <34 weeks. A binary regression model assessed the association between CL, UCA, and pre-term birth outcomes. The difference was statistically significant, with p<0.05. (3) Results: There was no statistically significant difference in the rate of preterm birth <37 weeks and <34 weeks between the two groups (16.3% vs. 11.8% and 6.5% vs. 4.9%, p>0.05). The probability of preterm birth <37 weeks in the group of pregnant women with a UCA ≥95o treated via cervical pessary plus progesterone decreased by 60.6%, OR (95% CI) of 0.394 (0.165-0.941), p<0.05. In the group of pregnant women with a UCA ≥105o, there was a significant association in the group of progesterone treatment combined with a cervical pessary, with the lower rate of PTB <37 weeks and <34 weeks, with OR (95% CI) of 0.028 (0.005-0.146), p<0.001, and 0.141 (0.030-0.664), p<0.05, respectively. (4) Conclusion: The results of this study suggest that cervical pessary is beneficial to the prevention of preterm birth in singleton pregnant women with an obtuse uterocervical angle. Further randomized studies among pregnant women with obtuse uterocervical angles will be needed to clarify the role of a cervical pessary in preventing preterm birth.

This paper examines the potential of large language models, specifically ChatGPT, BingChat, and Bard, in enhancing the work of teachers in various educational settings. These models, powered by cutting-edge artificial intelligence, offer a wide range of applications that can aid educators in curriculum development, personalized instruction, student engagement, and administrative tasks. By harnessing the capabilities of these language models, teachers can not only streamline their workload but also improve the overall quality of education. This paper explores the ways in which these models can empower educators and revolutionize teaching practices.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

In 2011-2012, Northern Vietnam suffered its first large scale hand foot and mouth disease (HFMD) epidemic. Two sets of official guidelines were issued during the outbreak to handle the HFMD crisis. The city of Hai Phong was therefore used as a model to analyze the impact of the guidelines release. 9621 HFMD cases were reported in Hai Phong city from April 2011 to December 2012. Three distinct waves of HFMD occurred. Enterovirus A71 and Coxackievirus A16 were successively associated to the epidemics. Two periods, before and after guidelines realease, could be distinguished which were characterized by different patient patterns Time to admission and severity changed notably. Guideline publication help the health system refocusing on the 0.5-3 years age group with highest incidence of the disease. The three waves showed different special distribution but main routes of infection were rivers and local secondary roads most likely through local trade and occupational movements of people.

This paper presents an improved indoor localization system based on RF and ultrasonic signal which we named SNSH system. This system composes of a transmitter mounted in a mobile target, and a series of receiver nodes which are managed by a coordinator. By measuring Time Delay of Arrival (TDoA) of RF and ultrasonic signal from the transmitter, distance from target to receiver node is calculated and sent to the coordinator through CAN network, and all the information are gathered in PC to estimate 3D position of the target. Sine wave detector and dynamic threshold filter are applied to provide excellent accuracy of range measurement from TDoA result, and multilateration algorithms is realized to optimize coordinate determination accuracy. Specifically, Linear Least Square and Non-linear Least Square techniques are implemented to contrast their performances in target coordinate estimation. RF signal encoding/decoding time, time delay in CAN network and math calculating are carefully considered to ensure optimal system performance and get ready for field application. Experiments show that sine wave detector algorithm has greatly improved range measurement accuracy, with mean error at 2.2mm and maximum error at 6.7 mm, for distance below 5m. In addition, 3D position accuracy is greatly enhanced by multilateration methods, with mean error in position stay under 15mm, and 90% confident error values at 23mm for LLS, 20mm for NLS. Overall system update period has been verified in real system operation, with maximum rate at 25ms, and compared with other existing researches.

Countless disasters have resulted from climate change, causing severe damage to infrastructure and the economy. These disasters have significant societal impacts, necessitating mental health services for the millions affected. To prepare for and respond effectively to such events, it is crucial to understand people's emotions and the life incidents they experience both before and after a disaster strikes. In this case study, we mined the emotions and life incidents expressed on Twitter during the 2017 Hurricane Harvey. Between August 20 and August 30, we collected a dataset of approximately 400,000 public tweets related to the storm. Using a BERT-based model, we predicted the emotions associated with each tweet. Following emotion prediction, we applied various natural language processing techniques to analyze the content of the tweets, aiming to uncover the 'topics' discussed alongside specific 'emotions.' To efficiently identify these topics, we utilized the Latent Dirichlet Allocation (LDA) technique for topic modeling, which allowed us to bypass manual content analysis and extract meaningful patterns from the data. However, rather than stopping at topic identification, we further refined our analysis by integrating Graph Neural Networks (GNN) and Large Language Models (LLM). The GNN was employed to generate embeddings and construct a similarity graph of the tweets, which was then used to optimize clustering. This step ensured that related tweets were accurately grouped together based on their content and context. Subsequently, we used an LLM to automatically generate descriptive names for each event cluster. This advanced approach allowed us to identify and label life incidents automatically, providing a nuanced understanding of the key issues faced by the community during the hurricane. The results revealed significant emotional shifts as the hurricane reached its most devastating phase. These shifts coincided with pressing concerns and demands from the population, such as evacuation plans, animal safety, safety updates, public policy, help requests, flood impacts, and the spread of fake news. By combining GNN and LLM for automatic event name prediction, our study not only mapped out the emotions but also accurately categorized the specific life incidents that were most relevant during the disaster, offering critical insights for disaster preparedness and response strategies.

Better understanding of the quality of life among nursing home residents with dementia is im-portant for developing interventions. The objectives of this cross-sectional study were to examine factors associated with poor health-related quality of life in older adults with dementia living in nursing homes in Hanoi, Vietnam. In-person interviews were conducted with 140 adults 60 years and older with dementia and information about their quality of life was obtained using the Quality of Life in Alzheimer’s Disease scale (QOL-AD). A number of sociodemographic and clinical factors associated with poor health-related quality of life (lowest tertile) were assessed through the results of physical tests, interviews with nursing home staff, and review of medical records. The average age of the study sample was 78.3 years, 65% were women, and their av-erage QOL-AD total score was 27.3 (SD = 4.4). Malnutrition, total dependence in activities of daily living, and urinary incontinence were associated with poor quality of life after controlling for multiple potentially confounding factors. Our findings show that Vietnamese nursing home residents with dementia have a moderate quality of life and interventions based on comprehen-sive geriatric assessment remain needed to modify risk factors associated with poor health-related quality of life.

This article summarizes studies using the AIQS-DB method to analyze various types of samples for different purposes. This is a method developed to simultaneously analyze nearly 1500 compounds and is widely used worldwide. The method is highly effective for environmental samples such as water, soil, sediment, and air. Recognizing its potential, this article aims to promote the further application and development of AIQS-DB in research related to food analysis and source tracing. Furthermore, if a suitable dataset can be constructed, it could help research quickly and cost-effectively discover the new bioactive compounds from plant medicine.

Land-use planning plays an important role in agricultural development, however it lacks tools to support planner in proposing land-use planning solutions especially, under saltwater intrusion condition in the coastal regions. This study aims to apply optimization in analyzing land-use solutions for agricultural land-use planning. In which a multi-objective optimization model is developed to optimize land-use area including land-use allocation taking into account socio-economic and environmental factors. The model has been applied in three districts of Soc Trang province, Vietnam (Long Phu, My Xuyen and Tran De) representing three ecological regions including salt water, brackish water and freshwater in the Mekong Delta of Vietnam. The results showed that two multi-objective optimization scenarios (in terms of profit, labor, environment benefits and risk reduction) have been implemented: (i) Multi-objective optimization of agricultural land-use until 2030 under normal conditions; (ii) Optimizing agricultural land-use until 2030 under climate change conditions similar to the 2016 drought and saltwater intrusion phenomenon in the Mekong Delta. The results showed that the second scenario is the option considered for implementing land-use plan thanks to the balance between good profits and minimizing economic and environmental risk. The land allocation was carried out taking into account household economic, the influence of adjacent production types, local traffic and canal systems factors to allocate optimal land-use areas. The combination of land-use optimization and spatial allocation process can help planners improve the quality of agricultural land-use planning.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

Background. There is limited evidence on the relationship between chronic kidney disease (CKD) and frailty in older people in Vietnam. This study aimed to examine the prevalence of frailty and its impact on mortality in older patients with end-stage renal disease. Method. This is a prospective, observational study at two large Dialysis Centres in Vietnam from November 2020 to June 2021. Consecutive older patients diagnosed with end-stage renal disease and on dialysis were recruited. Participants’ frailty status was defined by the Clinical Frailty Scale (CFS). The study outcome was all-cause mortality at 6th month. Results. A total of 175 participants were recruited (mean age 72.4 years, 58.9% female). Using the cut-point of CFS ≥4, 87.4% of the participants were frail. Mortality at 6th month was 14.9%, 31.9% in participants with CFS ≥7, 12.8% in participants with CFS=6, 7.5% in participants with CFS from 4 to 5, and 4.5% in participants with CFS ≤3 (p=0.001). Cox regression analysis showed that compared to the non-frail participants, the probability of death over 6 months was nearly 2-fold higher in the mildly frail, 3-fold higher in the moderately frail, and 9-fold higher in the severely frail participants. Conclusion. This study demonstrated a very high prevalence of frailty in older patients with end-stage renal disease and dialysis and the significant impact of frailty severity on mortality. Healthcare providers should consider incorporating frailty screening into routine care for older patients with end-stage renal disease and dialysis.

Microstructured surfaces are renowned for their unique properties, such as waterproofing and low adhesion, making them highly applicable in the biomedical field. These surfaces play a crucial role in influencing cell response by mimicking the native microenvironment of biological tissues. In this study, we engineered a series of biomimetic micropatterned surfaces using polydimethylsiloxane (PDMS) to explore their effects on primary breast cancer cell lines, contrasting these effects with those observed on conventional flat surfaces. The surface topography was varied to direct cells’ attachment, growth, and morphology. Our findings elucidate that surface-free energy is not merely a background factor but plays a decisive role in cell dynamics, strongly correlating with the spreading behaviour of breast cancer cells. Notably, on micropillar surfaces with high surface-free energy, an increase in the population of cancer cells was observed. Conversely, surfaces characterised by lower surface-free energies noted a reduction in cell viability. Moreover, the structural parameters, such as the gaps and diameters of the pillars, were found to critically influence cellular dispersion and adherence, underscoring the importance of the microstructures’ topography in biomedical applications. These insights pave the way for designing advanced microstructured surfaces tailored to specific cellular responses, opening new avenues for targeted cancer therapies and tissue engineering.

Background: There has been evidence that metabolic syndrome (MetS) may increase the risk of frailty. However, there is limited evidence on this association in Asian populations. Aims: This study aims to identify the association between MetS and frailty in older people in Vietnam. Methods: This is a cross-sectional analysis of a dataset obtained from an observational study on frailty and sarcopenia in patients aged ≥60 at a geriatric hospital in Vietnam. Frailty was defined by the frailty phenotype. Participants were defined as having MetS if they had ≥3 out of 5 criteria from the definition of the National Cholesterol Education Program (NCEP) Adults Treatment Panel (ATP) III. Multiple logistic regression models were performed to estimate the risk of having frailty in patients with MetS. Results: There were 669 participants (mean age 71, 60.2% female), 62.3% had MetS and 39.0% was frail. The prevalence of frailty was 42.2% in participants with MetS, 33.7% in participants without MetS (p=0.029). On logistic regression models, MetS was associated with increased likelihood of being frail (adjusted OR 1.52, 95%CI 1.01-2.28), allowing for age, sex, education, nutritional status, history of hospitalisation and chronic diseases. Conclusion: There was a significant association between MetS and frailty in this population. Further longitudinal studies are required to confirm this association.

In this paper, the seven traditional models of PV modules are reviewed comprehensively to find out the appropriate model to be reliable. All the models are validated using the Matlab code and make a graphical comparison. The accuracy and convergence of each model are evaluated using data of manufactured PV panels. Then, a novel model is proposed showing its consistent performance. The most three key parameters of single-diode model are self revised to adapt to various type of PV modules. This new method is verified in three types of PV panels' data measured by National Renewable Energy Laboratory (NREL), US. The validated data show promising results when the error RMSEs' range of the proposed model is under 0.36.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

In this study, effects of molecular structure transformation of canna starch (CS) in oxidation condition on physicochemical characteristics of thermoplastic starch were examined. Thermoplastic starch (TPS) samples of CS and respective oxidized starch (in 1, 3 and 5% of sodium hypochlorite, w/w) were prepared by using an internal mixer with the presence of 30 wt% of glycerol as plasticizer. The physicochemical, morphological, thermal, and mechanical properties of native starch-based TPS (NTPS) and oxidized starch-based TPS (OTPS) samples were evaluated. The content of carboxyl and carbonyl groups in oxidized canna starch (OCS) increased with the increase in the content of oxidant, leading to an improvement in the plasticization of CS. FTIR spectra of OTPS samples showed the stronger interaction between oxidized starch and plasticizer. SEM images of fracture surface indicated that the morphology of OTPS samples were smoother than that of NTPS samples. XRD patterns confirmed that the crystallite type of starches was also clearly changed after extrusion process and the decrease in crystallinity of OTPS samples is attributed to effects of both oxidation and plasticization. DSC results indicated that Tg of OTPS was greatly influenced by the carbonyl and carboxyl content and the higher content of these groups in oxidized starched could help the plasticization becomes easier. The better plasticization in OTPS samples resulted in the better mechanical properties and thermal stability of OTPS. The outcome suggested that the use of oxidized starch is an effective method to improve the plasticization in preparing thermoplastic starch.

In an age of market liberalization, globalization, and expanding agribusiness, there is a danger that small-scale farmers will find difficulty in fully participating in the market economy. One of the solutions to solve the above situation is to strengthen linkages between farmers and firms through contract farming. The purpose of this study is to assess the factors affecting the level of linkages between businesses and farmers in crop development in Thai Binh province, Vietnam. The two main research methods used were exploratory factor analysis (EFA) and regression analysis with survey data which was conducted from 300 farmers, 10 firms, and 15 factors related to contract-farming. The results indicated that there are 5 factors that significantly affect the level of participation of farmers in the linking process, the order of impacts from strong to weak is as follows: (1) Commitment and sharing of benefits and risks between farmers and firms in the linking process, (2) Issues related to management skills and enterprises capacity of link firms, (3) Price issues that farmers are interested in in the process of implementing links with firms, (4) Policy environment - Institutions related to farmer contracts between firms and farmers, (5) Household awareness about the benefits brought about by farmer contracts with firms. Based on results, a number of specific solutions have been proposed to enhance the efficiency of farming contracts between firms and farmers in cultivation production.

During the pandemic, home-cooked meals have received more attention as people get more time for themselves and their families. It cannot deny that people have more time to prepare meals, and it is safer to cook at home since they can avoid direct contact with people who can potentially F0 or F1. For that particular reason, the number of home cooking has increased rapidly. In the article, the author pointed out that in comparison to the previous time, 42.0 percent of respondents said they cooked more frequently during the lockdown, while just 7.0 percent said they cooked less frequently. The increase in cooking frequency had a more significant impact on women than on men (p<0.05). Those who said they cooked more regularly spent more time preparing meals (78\%) and trying new recipes (73.6\%), as well as spending more time baking (67.1 percent ). In particular, the consumption of “comfort” foods (salty snacks, sweets) showed a significant rise, ranging from (23\%) to (60\%) of respondents who declared snacking more studied.Moreover, articles pointed out that in conjunction with the dramatic reduction in energy expenditure due to the impossibility of going out, this situation could have led to energy imbalance and, thus, weight gain. Noticing the massive rise in home cooking, the search for new recipes, and the need for balance meals, the idea for a cooking app called "Cooking Papa" has been proposed. As far as the research goes, the concept of "cooking" seems close but yet not easy to define. The Oxford English Dictionary defines cooking as “to prepare food by the action of heat. However, limited evidence suggests that people interpret the meaning of cooking quite differently. Moreover, the terms ‘homemade’, ‘convenience,’ ‘proper cooking,’ ‘cook,’ ‘basic ingredients,’ and ‘ready prepared’ are not uniformly understood.

Recently, federated learning (FL) has been receiving great attention as an effective machine learning method to avoid the security issue in raw data collection as well as to distribute the computing load to edge devices. However, even though wireless communications is a essential part for implementing FL in edge networks, there have been a few works that analyze the effect of wireless networks on FL. In this paper, we investigate FL in small-cell networks where multiple base stations (BSs) and users are located according to homogeneous Poisson point process (PPP) with different densities. We comprehensively analyze the effects of geographic node deployment on the model aggregation in FL on the basis of stochastic geometry-based analysis. We derive the closed-form expressions of coverage probability with tractable approximations and discuss the minimum required BS density for achieving a target model aggregation rate in small-cell networks. Our analysis and simulation results provide insightful information for understanding the behaviors of FL in small-cell networks, and it can be exploited as a guideline for designing the network facilitating the wireless FL.

Advances in cardiovascular therapies and cancer treatments result in longer patient survival. The coexistence of cancer and cardiovascular disease has been recognized as a complex clinical scenario. Beside cardiovascular disease, older people with cancer are at greater risk of experiencing multimorbidity and the geriatric syndromes such as frailty. In older people, the concurrent presence of cancer and cardiovascular disease increased the risk of mortality, and the presence of frailty can exacerbate their conditions and hinder the treatment effectiveness. Given the significant intersection among frailty, cardiovascular disease and cancer in older people, this paper aims to provide an overview of the current research in this field and identifies gaps in research to understand the burden and impact of frailty in these populations. While many studies have examined the prevalence and impact of frailty on adverse outcomes in patients with cancer or with cardiovascular disease, evidence of frailty in individuals with both conditions is lacking. There is no universally accepted definition of frailty, which leads to inconsistencies in identifying and measuring frailty in older adults with cardiovascular disease and cancer. The frailty index seems to be a preferred frailty definition in studies in patients with cancer, while the frailty phenotype seems to be more commonly used in cardiovascular research. However, differences in how the frailty index was categorised and in how patients were classified as ‘frail’ depending on the cut points may have negative effect on understanding the impact of frailty in the studied populations. This makes it challenging to compare findings across different studies and limits our understanding of the prevalence and impact of frailty in these populations. Addressing these research gaps will contribute to our understanding of the burden of frailty in older people with cardiovascular disease and cancer, and improved clinical care protocols in this vulnerable population.

Changing climate conditions and rapidly increasing carbon dioxide emissions have severely affected the global ecosystem and world economy. Governments around the world have paid attention to these resulting challenges and enacted many policies to reduce environmental pollution and carbon dioxide (CO2) emissions. This study aimed to determine and understand the relationship between innovation, foreign direct investment, economic growth, renewable consumption and CO2 emission in Vietnam. Information was collected annually based on the annual data of the General Statistics Office of Vietnam and World Bank from 2000 to 2022. Data processing was conducted using the STATA 17.0 software. The innovation affects Vietnam’s environmental pollution. Innovation positively affect environmental pollution in Vietnam; if Vietnam’s innovation were to increase by 1%, CO2 emissions would increase by 0.68%. The empirical research results of this study also show that renewable energy consumption has a negative effect on environmental pollution in Vietnam; if renewable energy were consumed at a 1% increase, CO2 emission would decrease by 0.51%. In addition, FDI inflows and economic growth have strongly positive affecting to environmental pollution; if Vietnam’s FDI inflows were to increase 1%, CO2 emissions would increase 1.39%; if Vietnam’s GDP increase 1% then CO2 emission would increase 1.26%. This paper also provides some recommendations that can assist Vietnam in developing a green and sustainable economy in the technology revolution 4.0 to achieve the United Nations Sustainable Development Goals (SDGs) over a long-term period.

Background: Acute hepatopancreatic necrosis disease (AHPND), is a bacterial disease of whiteleg shrimp, which has a high mortality rate (100%) and incurs economic losses. Our objective was to identify the genes which lead to cell and organ damage and investigate bioproducts to prevent and treat. Methods: Litopenaeus vannamei shrimp in Thua Thien Hue province, Vietnam were collected from an infected pond and analysed at the Institute of Biotechnology, Hue University. The PirA gene of Vibrio parahaemolyticus strain K5 was isolated and analyzed for nucleotide sequence and paired with the expression vector pQE30. The expression vector was transformed into E. coli strain M15, the PirA recombinant protein was expressed in the form of 6xHis-PirA fusion protein of about 15 kDa. PirA recombinant protein was purified and determined the PirAvp binding ratio, cloning and sequencing of PirA gene from Vibrio parahaemolyticus strain K5 causing AHPND by PCR method with specific primers and molecular weights of PirAvp and the PirAvp complex. Results: PirA gene from Vibrio parahaemolyticus strain K5 was cloned into pGEM-T easy vector (Promega, USA) and screened E. coli TOP10 colonies containing pGEM T easy/PirA recombinant plasmid on LB agar/ampicillin/IPTG/X-Gal medium. PCR showing a band of about 347 bp, matching the size of PirA gene and two nucleotide sequences (BamHI and HindIII). The results showed that PirA gene has a length of 336 bp and similar to PirA gene on GenBank (Code: KU556825.1). The results of protein extracted from E. coli M15 recombinant cells and 6xHis-PirA target protein was collected in elution fractions from EF2 to EF6, showed that the concentration of 6xHis-PirA protein and EF3 elution fraction collected a highest protein concentration (1,586.54 µg/ml). Conclusions: The purified PirA recombinant protein will provide materials for development research to create biological products to prevent and treat AHPND.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

Droughts have a substantial effect on water resources, agriculture, and ecosystems on a worldwide scale. In the Mekong Delta of Vietnam, droughts exacerbated by climate change are significantly endangering the region's agricultural sustainability and output. Conventional forecasting techniques frequently do not capture the intricate dynamics of meteorological phenomena associated to drought effectively, prompting the exploration of more advanced methodologies. This work utilises artificial intelligence, par-ticularly machine learning methods like Gradient Boosting and Extreme Gradient Boosting (XGBoost), to enhance drought pre-diction in the Mekong Delta. The study utilises data from 11 meteorological stations spanning from 1990 to 2022 to create and evaluate Machine Learning models based on several climatic factors. We utilise Gradient Boosting and XGBoost algorithms to estimate the Standardised Precipitation-Evapotranspiration Index (SPEI) and evaluate their effectiveness in comparison to con-ventional forecasting techniques. The results show that Machine Learning, particularly XGBoost, surpasses traditional approaches in predicting SPEI accuracy at various time scales. XGBoost demonstrates skill in understanding the complex relationships between climatic factors, with R² values falling between 0.90 and 0.94 for 1-month forecasts. The progress highlights the potential of Machine Learning in improving drought management and adaptation tactics, proposing the incorporation of Machine Learning forecasting models into decision-making processes to enhance drought resistance in susceptible areas.

Proper satellite-based crop monitoring applications at the farm-level often require near-daily imagery at medium to high spatial resolution. The synthesizing of ongoing satellite missions by ESA (Sentinel 2) and NASA (Landsat7/8) provides this unprecedented opportunity at a global scale; nonetheless, this is rarely implemented because these procedures are data demanding and computationally intensive. This study developed a complete stream processing in the Google Earth Engine cloud platform to generate harmonized surface reflectance images of Landsat7,8 and Sentinel 2 missions. The harmonized images were generated for two agriculture schemes in Bekaa (Lebanon) and Ninh Thuan (Vietnam) during the period 2018-2019. We evaluated the performance of several pre-processing steps needed for the harmonization including image co-registration, brdf correction, topographic correction, and band adjustment. This study found that the miss-registration between Landsat 8 and Sentinel 2 images, varied from 10 meters in Ninh Thuan, Vietnam to 32 meters in Bekaa, Lebanon, and if not treated, posed a great impact on the quality of the harmonized dataset. Analysis of a pair overlapped L8-S2 images over the Bekaa region showed that after the harmonization, all band-to-band spatial correlations were greatly improved from (0.57, 0.64, 0.67, 0.75, 0.76, 0.75, 0.79) to (0.87, 0.91, 0.92, 0.94, 0.97, 0.97, 0.96) in bands (blue, green, red, nir,swir1,swir2, ndvi) respectively. We demonstrated that dense observation of the harmonized dataset can be very helpful for characterizing cropland in highly dynamic areas. We detected unimodal, bimodal and trimodal shapes in the temporal NDVI patterns (likely cycles of paddy rice) in Ninh Thuan province only during the year 2018. We fitted the temporal signatures of the NDVI time series using harmonic (Fourier) analysis. Derived phase (angle from the starting point to the cycle's peak) and amplitude (the cycle's height) were combined with max-NDVI to generate an R-G-B image. This image highlighted croplands as colored pixels (high phase and amplitude) and other types of land as grey/dark pixels (low phase/amplitude). Generated harmonized datasets that contain surface reflectance images (bands blue, green, red, nir, swir1, swir2, and ndvi at 30 meters) over the two studied sites are provided for public usage and testing.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Marketing is one of the important stages, the decisive factor affecting the success of production and business activities of every business. Therefore, marketing is considered to be the first and most important stage in the process of introducing, bringing products to market and branding of businesses, especially in the period when the disease situation is taking place very complicated worldwide. This study provides both qualitative and quantitative results for the following research objectives. Firstly, the study will assess the situation and analyze the appropriateness of marketing models in the current market situation trend. Secondly, the study proposes an approach in building a new type of marketing model, which is 3D web-based marketing applied in e-commerce to support the modeling of enterprise products in the form of Interactive 3D products are similar to real products. Thirdly, testing and evaluating 3D e-commerce web marketing model at Truong Hai Auto Showroom, Thai Nguyen City branch. This study also proposes a number of solutions for the research and deployment of 3D web marketing model application for businesses in the current market situation.

Stemming from the urgency of the actual situation, commercial banks need an effective credit risk management tool to limit risks. The authors went to survey, study and propose a set of factors affecting the ability of debt repayment of individual customers and conducting surveys. The topic uses data sets including 240 observation samples. Using the SPSS software to clean data and run the model based on Maddala's Binary logistics regression published in 1984 to find out the impact of each individual element of customers affecting their ability to repay such debts. Come on. The authors also specify the order of influence of each factor determining the ability to repay individual customers, thereby helping bank managers have a better visual view to make decisions for borrowing accurately, limiting risks.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

Non-timber forest products (NTFP) have contributed in various ways to the living, livelihoods, and trading of households and communities who live in rural and urban areas all over the world. This paper analyses the value chain of Jiaogulan (Gynostemma pentaphyllum) in the Cao Bang Geopark, Vietnam. 106 actors were surveyed using a semi-structured questionnaire: experts (agricultural extension officers, farmers' associations), harvesters, traders, primary processors, processors, distributors, and consumers. The results show that a map of Jiaogulan value chain, value added of households in main market channels, and impact of value added and distribution of Jiaogulan products on household income.

Cellular communications play pivotal roles in multi-cellular species, but they do so also in uni-cellular species. Moreover, cells communicate with each other not only within the same individual but also with cells in other individuals belonging to the same or other species. These communications occur between two unicellular species, two multicellular species, or between unicellular and multicellular species. The molecular mechanisms involved exhibit diversity and specificity, but they share common basic features which allow common pathways of communication between different, and sometimes very different species. These interactions have been made possible by the high degree of conservation of the basic molecular mechanisms of interaction of many ligand-receptor pairs in evolutionary remote species. These inter-species cellular communications played crucial roles during Evolution and must have been positively selected, particularly when collectively beneficial in hostile environments. We think that communications between cells did not arise after their emergence but was part of the very nature of first cells. Synchronization of populations of non-living protocells through chemical communications may have been a mandatory step towards their emergence as populations of living cells and explain the large commonality of cell communication mechanisms among microorganisms, plants, and animals.

Artificial Intelligence innovations, such as chatbots and specialized education suggestion tools, provide potential interactive and on-demand pedagogical engagement between non-Christians and Christians with Christianity. However, there is little empirical research on the readiness, acceptance, and adoption of A.I.'s involvement in religious education in a secular state, such as Vietnam. This research addresses the literature gap by providing an entrepreneurial analysis and customer perspectives on the ideas of A.I.'s involvement in religious education. Specifically, the study explores whether the Vietnamese across different ages and religious orientations accept and have enough skills to adopt A.I.'s religious education innovation. The interview sample is 32 participants, selected based on their religious orientation (Christians & Non-Christians) and age (Generation X, Generation Y & Generation Z). Most respondents are open to A.I. application in religious education except for the Church's personnel. However, only gen Z generations are fully prepared to adopt this innovation. Theoretically, the research customizes the Unified Theory of Acceptance and Use of Technology model into religious innovation context. Practically, this research acts as market research on the demand for A.I.'s religious innovation in Vietnam, an insight for future religious tech entrepreneurs.

Background University students’ psychological health is linked to their academic satisfaction. This study aimed to investigate students’ psychological health and academic satisfaction in the context of COVID-19 and academic year-end stress. Methods Standardized self-filled scales for anxiety, depression, stress, psychological well-being, and an ad-hoc COVID-19 stress scale were used in this cross-sectional study. Participants were first- to third-year students of eight different health-related tracks in Geneva, Switzerland. Descriptive statistics and hierarchical regression analyses were applied. Results In June 2020, out of 2835 invited students, 433 (15%) completed the survey. Academic satisfaction was a stronger mental health predictor than COVID-19, which mainly predicted stress and anxiety. Lower academic satisfaction scores were significantly associated with stress (β = -.53, p < .001), depression (β = -.26, p < .001), anxiety (β = -.20, p < .001), while higher scores with psychological well-being (β = .48, p < .001). Being female was strongly associated with anxiety and stress but not with depression or psychological well-being. Lower age was associated with stress only. The nature of the academic training had a lesser impact on mental health and the academic year none. Compared to students starting the academic year, year-end students reported significantly lower academic satisfaction, higher depression, and particularly higher anxiety and stress. There was, however, no difference in psychological well-being. Conclusion Students suffer more from anxiety, stress, depression, and lower satisfaction with studies at the end of the academic year than at the beginning. Academic satisfaction plays a more substantial role than COVID-19 in predicting students’ overall mental health status. Training institutions should address the underlying factors that can enhance students’ academic satisfaction, especially during the COVID-19 period, in addition to ensuring that they have a continuous and adequate learning experience, as well as access to psychosocial services that help them cope with mental distress and enhance their psychological well-being.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

The art of representing source code is pivotal in numerous programming analysis applications. Recent strides in neural networks have marked notable successes in this realm. However, the peculiar structural characteristics inherent in programming languages have not been fully exploited in existing models. While neural models based on abstract syntax trees (ASTs) adeptly manage the tree-like nature of source codes, they fall short in discerning the diverse substructural nuances within programs. This paper introduces the Dynamic Syntax Tree Model (DSTM), an innovative approach that fuses various neural network modules into tree architectures tailored to the specific AST of the input. Distinct from preceding tree-based neural models, DSTM adeptly discerns the semantic variances across different AST substructures. We validate DSTM through rigorous testing in program classification and code clone detection, outperforming contemporary methods and demonstrating the benefits of harnessing intricate source code structures.