The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

Reduced-order electrothermal models play a key role in the design and control of lithium- ion cell stacks, calling for accurate model parameter calibration. This paper presents a complete electrical and thermal experimental characterization procedure for coupled modeling of cylindrical lithium-ion cells in order to implement them in a prototype Formula SAE hybrid racing car. The main 4goal of the tests is to determine cell capacity variations with temperatures and discharge currents, to predict the open circuit voltage of the cell and its entropic component. A simple approach for the characterization of the battery equivalent electrical circuit and a two-steps thermal characterization method are also shown. The investigations are carried out on four commercial 18650 NMC lithium cells. The model demonstrated to predict the battery voltage at a RMS error lower than 20mV and the temperature to a RMS error equal to 0.5 ◦C. The authors hope that this manuscript can contribute to the development of standardized characterization techniques for such cells, while offering experimental data and validated models that can be used by researchers and BMS designers in different applications.

This study examines the prospective association of egg consumption with multiple domains of cognitive function in older, community-dwelling men and women followed 16.3 years. Participants were 617 men and 898 women from the Rancho Bernardo Cohort aged 60 and older who were surveyed about egg intake/week in 1972-74, and attended a 1988-91 research visit when cognitive function was assessed with 12 tests. Analyses showed that egg intake ranged from 0-24/week (means: men=4.23.2, women=3.52.7, p<0.0001). In men, covariate-adjusted regressions showed egg intake was associated with better performance on Buschke total (p=0.04), long-term (p=0.02) and short-term (p=0.05) recall. No significant associations were observed in women (p’s>0.05). Analyses in those <60y at in 1972-74 showed egg intake was positively associated with scores on Heaton copying(p<.04) and the Mini-Mental Status Exam(MMSE;p<.02) in men, and category fluency(p<0.05) in women. Egg intake was not significantly associated with odds of poor performance on MMSE, Trails B, or category fluency in either sex. These reassuring findings suggest there are no long-term detrimental effects of egg consumption on multiple cognitive function domains, and for men, there may be beneficial effects for verbal episodic memory. Egg consumption in middle-age may also be related to better cognitive performance later in life.

There have been a great number of investigations about the influence of weak magnetic fields on biological systems, such as isolated cells and whole organisms. This is also a subject of considerable medical concern since old epidemiologic observations have indicated a possible tumorigenic effect of these fields. Their mechanism of action, however, is not firmly established. A large number of biological effects of electromagnetic fields have been attributed either to the production of reactive oxygen species (ROS) or to the entrance Ca²⁺ in the cell. A new biochemical pathway is proposed that covers these two possibilities: the primary effect of the magnetic field would be by the mechanism of radical pairs resulting in the production of ROS; these could activate the ion channels TRPM2 producing cellular inflow of Ca²⁺, which would induce the calcium dependent effects. Thus, a large number of biological effects observed up to the present could be explained.

Tribology is related to all studies on friction, wear and lubrication. One of the main aims of these studies is a reduction in friction and wear. Tribology is extremely vast, being also multidisciplinary and interdisciplinary. Therefore, it is very difficult to organize the several tribology subjects in an unique way and different classifications have been proposed by different authors. In this work, the several subjects treated by tribology are reviewed and organized in six branches: Fundamental Tribology, Tribology of Materials and Lubricants, Micro and Nanotribology, Industrial Tribology, Biotribology and New Frontiers of Tribology. The main subjects treated by the six branches are briefly reviewed in the paper in order to highlight the vastness of tribology and its important contribution to sustainability. Particularly friction and wear reductions are strictly related to greater efficiency and material saving, which mean less energy losses and material wastes, less pollution and therefore a more sustainable life according to the Sustainable Development Goals. The connections among the latter and the several different tribological subjects are discussed.

We prove that the Legendre coefficients associated with a function f(x) can be represented as the Fourier coefficients of a suitable Abel-type transform of the function itself. Thus, the computation of N Legendre coefficients can be performed efficiently in O(NlogN) operations by means of a single Fast Fourier Transform of the Abel-type transform of f(x). We also show how the symmetries associated with the Abel-type transform can be exploited to further reduce the computational complexity. The dual problem of calculating the sum of Legendre expansions is also considered. We prove that a Legendre series can be written as the Abel transform of a suitable Fourier series. This fact allows us to state an efficient algorithm for the evaluation of Legendre expansions. Finally, numerical tests are presented to exemplify and confirm the theoretical results.

Background: Amyloid beta peptides (Aβ) have been identified as the main pathogenic agents in Alzheimer’s disease (AD). Soluble Aβ oligomers, rather than monomer or insoluble amyloid fibrils, show membrane-binding capacity to red blood cells (RBCs) and trigger several morphological and functional alterations in RBCs that can result in impaired oxygen transport and delivery. Since bioactive lipids have been recently proposed as potent protective agents against Aβ toxicity, we investigated the role of sphingosine-1-phosphate (S1P) in signaling pathways involved in the mechanism underlying ATP release in Aβ-treated RBCs. Methods: In RBCs following different treatments, ATP, 2,3 DPG, cAMP levels, and caspase 3 activity were determined by spectrophotometric and immunoassay. Results: S1P rescued the inhibition of ATP release from RBCs triggered by Aβ through a mechanism involving caspase-3 and restoring 2,3 DPG and cAMP levels within the cell. Conclusions: These findings reveal the molecular basis of S1P protection against Aβ in RBCs and suggest new therapeutic avenues in AD.

Biological systems often need to operate in complex environments where conditions can rapidly change. This is possible due to their inherent ability to sense changes and adapt their behavior in response. Here, we detail recent advances in the creation of synthetic genetic parts and circuits whose behaviors can be dynamically tuned through a variety of intra- and extra-cellular signals. We show how this capability lays the foundation for implementing control engineering schemes in living cells and allows for the creation of biological systems that are able to self-adapt, ensuring their functionality is maintained in the face of varying environmental and physiological conditions. We end by discussing some of the broader implications of this technology for the safe deployment of synthetic biology.

A thermodynamic analysis of population dynamics and of sustainability provides rigor to many important issues. In this work, the “system Society” is analysed in connection with the “system Environment” using an exergy metric, and the method includes an internalization of the Externalities (Capital, Labour, Environmental effects) conducted on the basis of a “system+ environment” balance. In this perspective, this study investigates the Late Pleistocene extinction of the Homo Neandertalensis, which took place in a geologically short time and in the presence of a competing species, the Homo Sapiens. The case in study is not trivial, and its choice not casual: in those times, the only factor that could lead to an advantage of one group over the other was their respective resource use intensity. A specific indicator, the Exergy Footprint, is here applied to measure the total amount of primary resources required to produce a certain (material or immaterial) commodity, including the resources needed for the physical survival of the individuals. On the basis of the available data, the results show that the EF of the Neandertal was higher than that of the Sapiens, and that, both species sharing the same ecological niche in a time of dwindling resources, the less frugal was also more fragile in an evolutionary sense.

The study presents an updated overview of the 14 non-endemic threatened Crop Wild Relatives (CWR) in Italy: Aegilops biuncialis, Ae. uniaristata, Ae. ventricosa, Asparagus pastorianus, Beta macrocarpa, Brassica insularis, B. montana, Crambe hispanica subsp. hispanica, C. tataria subsp. tataria, Ipomoea sagittata, Lathyrus amphicarpos, L. palustris, Vicia cusnae and V. serinica. Geographical distribution, ecology (with plant communities and habitat 92/43/EEC aspects), genetics (focused on gene pools), property, and in situ and ex situ conservation were analyzed. In addition, with the aim of their protection and valorization, specific actions are recommended.

Ionic liquids have been recognised as interesting solvents applicable in the efficient lignocellulosic biomass valorisation, especially in the biomass fractionation into individual polymeric components or direct hydrolysis some of biomass fractions. Considering the chemical character of ionic liquids, two different approaches, paved the way for a fractionation of biomass. The first strategy integrated a pre-treatment, hydrolysis and conversion of biomass through the employment of hydrogen-bond acidic 1-ethyl-3-methyimidazolim hydrogen sulfate ionic liquid. The second one relied on the use of a three-step fractionation process with hydrogen-bond basic 1-ethyl-3-methylimidazolium acetate to produce high purity cellulose, hemicellulose and lignin fractions. The proposed approaches were scrutinised for wheat straw and eucalyptus residues. Those different biomasses allowed understanding that enzymatic hydrolysis yields are dependent on the crystallinity of pre-treated biomass. The use of acetate based ionic liquid allowed to change crystalline cellulose I to cellulose II and consequently enhanced glucan to glucose yield to 93.14.1 mol% and 82.91.2 mol% for wheat straw and eucalyptus, respectively. Whereas for hydrogen sulfate ionic liquid, the same enzymatic hydrolysis yields were 61.6  0.2 mol% for wheat straw and only 7.90.3 mol% for eucalyptus residues. These results demonstrate the importance of either ionic liquid character or biomass type on the efficient biomass processing.

Since 2015, outbreaks of foot-and-mouth disease (FMD) in the Middle East have been caused by a new emerging viral lineage, A/ASIA/G-VII. In-vitro vaccine matching data indicated that this virus poorly matched (low r1-value) with vaccines that were being used in the region as well as most other commercially available vaccines. The aim of this study was to assess the performance of two candidate vaccines against challenge with a representative field virus from the A/ASIA/G-VII lineage. The results from an initial full dose protection study provided encouraging data for the A/MAY/97 vaccine, while the A22/IRQ/64 vaccine only protected 2/7 vaccinated animals. In view of these promising results, this vaccine was tested in a potency test (PD50) experiment in which 5 cattle were vaccinated with a full dose, 5 cattle with a 1/3 dose and 5 cattle with a 1/9 dose of vaccine. Vaccines were prepared as would be done during an emergency vaccination campaign using a double oil emulsion adjuvant. At 21 days post vaccination these vaccinated cattle and 3 control cattle were subsequently challenged intradermolingually with a field isolate from the A/ASIA/G-VII lineage. All cattle from the full vaccine dose, 4 cattle from the 1/3 vaccine dose and 2 cattle from the 1/9 vaccine dose were clinically protected against challenge with FMDV A/ASIA/G-VII, resulting in a heterologous potency of 6.5 PD50/dose. These data support previous studies showing that a high potency emergency vaccine can protect against clinical disease when challenged with a heterologous strain of the same serotype. Not only the r1-value of the vaccine, but also the homologous potency of a vaccine should be taken into account when advising vaccines to control an outbreak.

This study describes the synthesis, and characterization of lead-free organic ferroelectric perovskite N-methyl-N’-diazabicyclo[2.2.2]octonium)-ammonium trichloride (MDABCO-NH4Cl3). The electrospinning technique was employed to obtain nanofibers embedded with this perovskite into PVC polymer for hybrid fiber production. The dielectric, piezoelectric and pyroelectric properties of these fibers were carefully examined. From measurements of the dielectric permittivity temperature and frequency dependence, together with the pyroelectric results, a transition from a high temperature paraelectric to a ferroelectric phase that remained down to room temperature, was found to occur at 438 K. A pyroelectric coefficient as high as 290 C K-1 m-2value obtained is within the same order of magnitude as that reported for MDABCO-NH4I3 and the semiorganic ferroelectric triglycine sulfate (TGS). The hybrid nanofibers exhibited good morphological characteristics and demonstrated very good piezoelectric properties. Specifically, a piezoelectric coefficient of 42 pC/N was obtained when a periodical force of 3 N was applied. The performance of these fibers is on par with materials discussed in the existing literature for fabrication of nano energy harvesting generators. Importantly, the perovskite nanocrystals within the fibers not harmed by oxidation, making them a promising environmentally friendly platform for flexible energy harvesting.

Nanostructured dipeptide self-assemblies exhibiting quantum confinement are of great interest due to their potential applications in the field of materials science as optoelectronic materials for energy harvesting devices. Among those, aromatic cyclo-dipeptides containing the amino acid tryptophan are wide-band gap semiconductors displaying high mechanical rigidity, photoluminescence and piezoelectric properties to be used in power generation. In this work, we report the fabrication of hybrid systems based on chiral cyclo-dipeptide L-Tryptophan- L-Tryptophan incorporated into biopolymer electrospun fibers. The micro/nanofibers contain self-assembled nanospheres embedded into the polymer matrix are wide-band gap semiconductors (gap energy 3.8 eV), display blue photoluminescence and relevant piezoelectric and pyroelectric properties with coefficients as high as 57 pCN-1 and 35×10-6 Cm-2k-1, respectively. They are therefore promise systems for thermal sensing and energy harvesting applications.

Hybrid biomaterials were engineered using the electrospinning technique, incorporating the dipeptide Boc-L-phenylalanyl-L-Isoleucine into microfibers composed of biocompatible polymers. The examination by scanning electron microscopy affirmed the morphology of the microfibers, exhibiting diameters ranging between 0.9 to 1.8 µm. The dipeptide self-assemblies into spheres with a hydrodynamic size between 0.18 to 1.26 µm. The dielectric properties of these microfibers were characterized through impedance spectroscopy, where variations in both temperature and frequency were systematically studied. The investigation revealed a noteworthy rise in the dielectric constant and AC electric conductivity with increasing temperature, attributable to augmented charge mobility within the material. The successful integration of the dipeptide was substantiated through the observation of Maxwell-Wagner interfacial polarization, affirming the uniform dispersion within the microfibers. In-depth insights into electric permittivity and activation energies were garnered using the Havriliak-Negami model and the AC conductivity behavior. Very importantly, these engineered fibers exhibited pronounced pyroelectric and piezoelectric responses, with Boc-Phe-Ile@PLLA microfibers standing out with the highest piezoelectric coefficient, calculated to be 56 pC/N. These discoveries help us understand how dipeptide nanostructures embedded into electrospun nano/microfibers can greatly affect their pyroelectric and piezoelectric properties. They also point out that polymer fibers could be used as highly efficient piezoelectric energy harvesters, with promising applications in portable and wearable devices.

Rhizosphere bacteria have a decisive influence on plant ionic adjustment, as well as in ameliorating plant growth under an array of stress situations. Plant growth-promoting rhizobacteria (PGPR) colonize the rhizosphere of plants and promote plant growth through mechanisms such as solubilization of mineral phosphates, biological N2 fixation, production of siderophores and phytohormones, and can induce systemic resistance in the plant. This can be of extreme importance when considering the restoration of salinized grounds by halophytic species. This present work aims to evaluate the physiological fitness and phytoprotection improvement by salt marsh PGPR in Halimione portulacoides under mild and severe salt stress. Plants inoculated with PGPR-consortium showed higher photochemical performances, improved antioxidant response, and promotion of osmotic balance traits, that boosted the individual’s ability to cope with mild salt stress. All these changes are also in line with the differential elemental profiles (Na, K, and Ca) observed in the different plant tissues. Even under severe salt stress, some physiological traits were improved when compared to the non-inoculated individuals. The results developed under this work, point out an important role of bioaugmentation in promoting plant fitness and improving salt tolerance, with a great potential for applications in seawater agriculture, restoration, and bio-reclamation of salinized soils.

The contamination of areas around solid urban waste dumps is a global challenge for the maintenance of environmental quality in large urban centres in developing countries. This study applied geophysical methods (electrical resistivity) to identify leachate contamina-tion plumes in the subsoil and groundwater, as well as to describe their temporal (2020 and 2021) dynamics in the lithology and groundwater around the Hulene - B waste dump, Maputo, Mozambique. Geophysical methods (electrical resistivity) were applied to identify possible groundwater contamination plumes, their dynamics, mechanisms of their enrichment and dispersion. Eight 400 m electrical resistivity profiles were performed, four profiles in January 2020 and four profiles in May 2021, overlapped, and the data were inverted with RES2D software. The electrical resistivity models indicate an E - W move-ment of large contamination plumes that dilute superficially into the natural surface wa-ter receiving basin and groundwater, creating zones of resistive anomalies. The thickness of the plumes in the subsurface environment was shown to be extensive in summer for profiles 1a and 2b and we associate it with the higher leachate production and migration mechanisms, which are intense in the hot and rainy season. Profile 4b showed the prop-agation of anomalous surface and subsurface areas, which was associated with higher leachate production and migration process in the new deposition zone (west). The spatial distribution of contamination plumes at both stations reduced significantly as we moved further away from the waste deposit, revealing the attenuating effect of groundwater and lithological substrate (Profile 3 a, b, and fig.7).

In this article we derive a closed form expression for the symmetric logarithmic derivative of Fermionic Gaussian states. This provides a direct way of computing the quantum Fisher Information for Fermionic Gaussian states. Applications range from quantum Metrology with thermal states to non-equilibrium steady states with Fermionic many-body systems.

We examine the mass balance of the glaciers in the Novaya Zemlya Archipelago, located in the Russian High Arctic using time series of time-variable gravity from the NASA/DLR Gravity Recovery and Climate Experiment (GRACE) mission, laser altimetry data from the NASA Ice Cloud and land Elevation Satellite (ICESat) mission, and radar altimetry data from the ESA CryoSat-2 mission. We present a new algorithm for detecting changes in glacier elevation from these satellite altimetry data and evaluate its performance in the case Novaya Zemlya by comparing the results with GRACE. We find that the mass loss of Novaya Zemlya increased from 10±5 Gt/yr over 2003-2009 to 14±4 Gt/yr over 2010-2016, with a brief period of near mass balance between 2009 and 2011. The results are consistent across the gravimetric and altimetric methods. Furthermore, the analysis of elevation change from CryoSat-2 indicates that 60\% of the mass loss occurs at low elevation, where thinning rates are highest. We also find that marine-terminating glaciers in Novaya Zemlya are thinning significantly faster than land-terminating glaciers, which indicates an important role of ice dynamics of marine-terminating glaciers. We posit that the glacier changes have been caused by changes in atmospheric and ocean temperatures. We find that the increase in mass loss after 2010 is associated with a warming in air temperatures, which increased the surface melt rates. There is no enough information on the ocean temperature at the front of the glaciers to conclude on the role of the ocean, but we posit that the temperature of subsurface ocean waters must have increased during the observation period.

In recent years, the term quantum-like has been increasingly used in different disciplines, including neurosciences, psychological and socio-economical disciplines, claiming that some investigated phenomena show “something” in common with quantum processes and, therefore, they can be modeled using a sort of quantum formalism. Therefore, the increasing use of the term quantum-like calls for defining and sharing its meaning in order to properly adopt it and avoid possible misuse. In our opinion, the concept of quantum-like may be successfully applied to macroscopic phenomena and empirical sciences other than physics when at least two conditions are satisfied: a) the behavior of the investigated phenomena show logical analogies with quantum ones; b) it is possible to find a criterion of truth based on an experiential/scientific approach applied to a probabilistic model of description of the phenomena. This is only a first, small step in the approach to the concept of quantum-like, hopefully helpful to promote further discussion and achieve a better definition.

Statins prevent cardiovascular diseases, yet their use is limited by the muscle disturbances they cause. Rarely, statin-induced myopathy is autoimmune, but more commonly it is due to direct muscle toxicity. Available evidence suggests that statin-induced creatine deficiency may be a major cause of this toxicity, and that creatine supplementation prevents it. Statins inhibit guanidinoacetate methyl transferase (GAMT), the last enzyme in the synthesis of creatine, thus they decrease its intracellular content. Such decreased content could cause mitochondrial impairment, since creatine is the final acceptor of the phosphate group of adenosine triphosphate (ATP) at the end of mitochondrial oxidative phosphorylation. Decreased cellular synthesis of adenosine triphosphate (ATP) would follow. Accordingly, ATP synthesis is decreased in statin-treated cells. In vitro, creatine supplementation prevents the opening of mitochondrial permeability transition pore caused by statins. Clinically, creatine administration prevents statin myopathy in statin-intolerant patients. Additional research is warranted to hopefully confirm these findings. However, creatine is widely used by athletes with no adverse events, and has demonstrated to be safe even in double-blind, placebo-controlled trials of elder individuals. Thus, it should be trialed, under medical supervision, in patients who cannot assume statin due to the occurrence of muscular symptoms.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

This paper aims to present the method of producing visual media for communicating the Asinara Island National Park plan. These products are landscape visualizations able to foster landscape preservation both from the point of view of the management of the landscape and of the citizen's involvement in the communication of the historical and environmental values of the landscape. Starting from landscape information gathering, the research has experimented with an operative method for processing different graphic representations from the same geographic database, calibrating the outputs to different audiences, their needs, objectives, and literacy skills. Three different types of products are presented: the first is a digital, dynamic and multisectoral decision-making GIS tool for park management. The second is a 3D model, aimed to the virtual fruition. The third is a map of the zoning park plan drawn to be easily readable to the non-expert public. This case study emerges as a replicable method to process the landscape information to make different visualization tools from a single geographic model, to meet the different requirements that arise from a complex landscape planning process.

Corporate Sustainability (CS) literature has gone through a period of intense development. The moment is favorable to gathering these contributions to consistently advance the state of the art in CS and, also, discuss them to apply in real contexts. The main objective of the paper is to systematize, through a systematic literature review using content analysis of the 30 most cited articles from 2007 to 2017, the guiding pillars of CS management. The systematic search for papers was carried out in Scopus and Web of Science and the initial screening of the papers was assisted by the coding software MAXQDA 2018, through which the authors structured and analyzed their main insights, contributions and conclusions. After getting acquainted with the sample, an in-depth reading of the texts was conducted and 60 CS elements were identified. The elements cited in the relevant literature were grouped into 6 pillars related to Corporate sustainability strategy; Corporate governance; Human resources management; Knowledge and innovation management; Measurement, disclosure and independent assurance; and Management systems and Integrated management systems. The discussion of CS management pillars presented in this study provides understanding to researchers and managers on the main aspects that make up the integration of this construct in the companies, especially from a management point of view.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Modern gas turbines firing temperatures (1500-2000K) are well beyond the maximum allowable blade material temperatures. Continuous safe operation is made possible by cooling the HP turbine first stages -nozzle vanes and rotor blades- with a portion of the compressor discharge air, a practice that induces a penalty on the cycle thermal efficiency. Therefore, a current issue is to investigate the real advantage, technical and economical, of raising maximum temperatures much further beyond current values. In this paper, process simulations of a gas turbine are performed to assess HP turbine first-stage cooling effects on cycle performance. A new simplified and properly streamlined model is proposed for the non-adiabatic expansion of the hot gas mixed with the cooling air within the blade passage, which allows for a comparison of several cycle configurations at different TIT (turbine inlet temperature) and max (total turbine expansion ratio) with a realistically acceptable degree of approximation.. The calculations suggest that, at a given max, the TIT can be increased in order to reach higher cycle efficiency up to a limit imposed by the required amount and temperature of the cooling air. Beyond this limit, no significant gains in thermal efficiency are obtained by adopting higher max and/or increasing the TIT, so that it is convenient in terms of cycle performance to design at lower rather than higher max. The small penalty on cycle efficiency is compensated by lower plant cost. The results of our model agree with those of some previous much more complex and computationally expensive studies, so that the novelty of this paper lies in the original method adopted on which the proposed model is based, and in the fast, accurate and low resource intensity of the corresponding numerical procedure: all advantages that can be crucial for industry needs. The presented analysis is purely thermodynamic, with no investigation on the effects of the different configurations on plant costs, so that future work addressing a thermo-economic analysis of the air-cooled gas turbine power plant is the next logical step.

Alcohol effects on hepatic lipid metabolism through various mechanisms, leading synergistically to an accumulation of fatty acids (FA) and triglycerides. Obesity, as well as, the dietary fat [saturated fatty acids (FA) versus poly-unsaturated fatty acids (PUFA)] may modulate the hepatic fat. Alcohol inhibits adenosine monophosphate activated kinase (AMPK). AMPK activates peroxisome proliferators activated receptor a (PPARα) and leads to a decreased activation of sterol regulatory element binding protein 1c (SRABP1c). The inhibition of AMPK, and thus of PPARα results in an inhibition of FAs oxidation. This ß-oxidation is further reduced due to mitochondrial damage induced through cytochrome P4502E1 (CYP2E1) driven oxidative stress. Furthermore, the synthesis of FAs is stimulated through an activation of SHREP1. In addition, alcohol consumption leads to a reduced production of adiponectin in adipocytes due to oxidative stress and to an increased mobilization of FAs from adipose tissue and from the gut as chylomicrons. On the other side, the secretion of FAs via very low density lipoproteins (VLDL) from the liver is inhibited by alcohol. Alcohol also affects signal pathways such as early growth response 1 (Egr-1) associated with the expression of tumour necrosis factor  (TNF), and the mammalian target of rapamycin (mTOR) a key regulator of autophagy. Both have influence the pathogenesis of alcoholic fatty liver. Alcohol-induced gut dysbiosis is contributing to the severity of ALD by increasing metabolism of ethanol in the gut and promoting intestinal dysfunction. Moreover, pathogen associated molecular paterns (PAMPS) via specific Toll-like receptors (TLR) bacterial overgrowth is leading to the translocation of bacteria. Endotoxins, and toxic ethanol metabolites enter the enterohepatic circulation reaching the liver, inducing the activation of the nuclear factor kappa-B (NFB) pathway. Pro-inflammatory cytokines released in the process contribute to inflammation and fibrosis. In addition, cellular apoptosis is inhibited in the favor of necrosis.

The worldwide number of migrants has had a rapid increase during the last fifteen years. Despite the extensive research studies that elucidate the increase in migrants' recipient countries, we know little about the relationship between the climate factors and human mobility in the countries of origin. Hence, this study focuses on the effects of weather and the propensity of individuals to leave a territory by measuring the importance of rain precipitation or the lack of it in one of the critical food corridors of Central America, formed by El Salvador, Honduras, and Guatemala. To study the mobility process, we develop a stochastic frontier model; the main result shows a greater propensity to migrate when there is a significant drought event in the place of origin. Some other factors that motivate people to leave their homeland are the effect of other climate events measured through the control system (ENSO), homicide levels, economic performance, and exchange rate. The findings allow differentiating between drought and excess precipitation on a population and mobility to other territories. In addition, these results permit us to derive observable implications of the different effects of flooding and drought and create public policies of prevention, mitigation, and resilience.

The CRISPR/Cas9 gene editing system has enormous potential in the treatment of multiple genetic disorders. To fully harness this potential, it is essential to deliver CRISPR-Cas9 components safely and effectively into the nuclei of target cells. In this study, we tested the amphipathic cell-penetrating peptide LAH5, previously used for DNA delivery, to intracellularly deliver spCas9: sgRNA ribonucleoprotein (RNP) and RNP/single-stranded homology-directed repair (HDR) template. We discovered that the LAH5 peptide effectively formed nanocomplexes with both RNP and RNP/HDR cargo, and that these nanocomplexes were taken up by cells effectively. Peptide/RNP nanocomplexes were characterized for size and charge, and nanocomplexation with RNP and RNP/HDR cargo was demonstrated via an electrophoretic mobility shift assay. Various ratios of peptide/RNP nanocomplexes were functionally screened on fluorescent reporter cell lines for gene editing and HDR-mediated gene correction. Additionally, targeted gene editing of the CCR5 gene was demonstrated in various cell lines. This LAH5-based delivery strategy paves the way for the development of therapeutic delivery systems for CRISPR/Cas-based genomic engineering.

The tumor microenvironment plays a pivotal role in the behavior and development of solid tumors as well as shaping the immune response against them. As the tumor cells proliferate, the space they occupy and their physical interactions with the surrounding tissue increases. The growing tumor tissue becomes a complex dynamic structure, containing connective tissue, vascular structures, and extracellular matrix that facilitates stimulation, oxygenation, and nutrition, necessary for its fast growth. Mechanical cues such as stiffness, solid stress, interstitial fluid pressure, matrix density, and microarchitecture influence cellular functions and ultimately tumor progression and metastasis. In this fight, our body is equipped with T cells as its spearhead against tumors. However, the altered biochemical and mechanical environment of the tumor niche affects T cell efficacy and leads to their exhaustion. Understanding the mechanobiological properties of the tumor microenvironment and their effects on T cells is key for developing novel adoptive tumor immunotherapies.

The potential use of nanostructured dipeptide self-assemblies in materials science for energy harvesting devices is a highly sought-after area of research. Specifically, aromatic cyclo-dipeptides containing tryptophan have garnered attention due to their wide-bandgap semiconductor properties, high mechanical rigidity, photoluminescence, and nonlinear optical behavior. In this study, we present the development of a hybrid system comprising biopolymer electrospun fibers incorporated with the chiral cyclo-dipeptide L-Tryptophan-L-Tyrosine. The resulting nanofibers are wide-bandgap semiconductors (bandgap energy 4.0 eV) and consist of self-assembled nanotubes embedded within a polymer matrix, exhibiting intense blue photoluminescence. Moreover, the cyclo-dipeptide L-Tryptophan-L-Tyrosine incorporated into polycaprolactone nanofibers displays a strong effective second harmonic generation signal of 0.36 pm/V and also shows notable piezoelectric properties with a high effective coefficient of 22 pCN−1. These hybrid systems hold great promise for applications in the field of nanoenergy harvesting and nanophotonics.

Energy consumption of processors and memories is quickly becoming a limiting factor in the deployment of large computing systems. For this reason it is important to understand the energy performance of these processors and to study strategies allowing to use them in the most efficient way. In this work we focus on computing and energy performance of the Knights Landing Xeon Phi, the latest Intel many-core architecture processor for HPC applications. We consider the 64-core Xeon Phi 7230, and profile its performance and energy efficiency using both its on-chip MCDRAM and the off-chip DDR4 memory as the main storage for application data. As a benchmark application we use a Lattice Boltzmann code heavily optimized for this architecture, and implemented using several different arrangements of the application data in memory (data-layouts, in short). We also assess the dependence of energy consumption on data-layouts, memory configurations (DDR4 or MCDRAM), and number of threads per core. We finally consider possible trade-offs between computing performance and energy efficiency, tuning the clock frequency of the processor using the Dynamic Voltage and Frequency Scaling (DVFS) technique.

Objectives: Few studies in literature evaluate the "mean measure" of root divergence. Most of them are linear measurements, they hardly describe the dental furcation conformation. It is left to the subjectivity of the operator deciding whether a furcation is convergent or divergent. The goal of this study is to create a visual evaluation method to overcome these problems giving a conformation of the entire interradicular space. Material and methods: A user-friendly software (Paint®, Windows10®) was used to measure endo-oral radiographs of upper and lower molars. Three kinds of measurements were taken. Three operators used the software to measure 20 radiographs, then the technique was repeated on 250 radiographic images to identify an average measurement. The ratio of these three measurements allowed to develop a new visual evaluation method of the interradicular space. Results: Intra and inter-operator reproducibility was statistically assessed on a sample of 20 anonymous endo-oral radiographs measured by 3 blind operators. Then, a sample of 250 anonymous endo-oral radiographs were measured by a blind operator and were statistically evaluated to identify an average value to define a main conformation of the interradicular space. Measurements made by the 3 operators on the 20 radiographic images showed that the technique is reproducible, and a mean value of the interradicular space was obtained. Conclusions: A new anatomical evaluation of the interradicular space in its entirety, which could help the clinicians in the therapy of furcated molars, can be obtained.

The seed industry plays a crucial role in the global food production, but it faces a persistent challenge in ensuring the health and quality of seeds, particularly those of tomato and pepper, which represent key seed commodities on the global market. Seeds can serve as potential pathways for the introduction and dissemination of seed-borne bacteria, which may have devastating effects on crop yield, farmers’ remunerability, and food security. Therefore, fungicides and other anti-microbial compounds are extensively used to disinfect the seeds, thus increasing the input of chemicals in the agri-enviroment. In this review, we address aspects that connect disease epide-miology with seed infection and health, including seed contamination, endophytic colonization, and seed-borne infections. We focused on the main bacterial diseases affecting tomato and pepper by discussing their official seed testing methods as requirements supporting a smooth seed trade. Moreover, we present a survey on the past and recent innovations for seed treatments, focusing on sustainable disinfection methods. Therefore, this review will be a short, but indispensable guide for seed technologists and pathologists involved in the production of high-quality seeds, providing indications and suggestions to contrast seed-borne pathogens dissemination, avoid international controversies and complaints by phytosanitary authorities, extension services and farmers.

Ensuring safe and continuous autonomous navigation in long-term mobile robot applications is still challenging. To ensure a reliable representation of the current environment without the need for periodic re-mapping, updating the map is recommended. However, in case of incorrect estimation of robot pose, updating the map can lead to errors that prevent the robot localisation and jeopardize map accuracy. In this paper, we propose a safe LIDAR-based occupancy grid map updating algorithm for dynamic environments taking into account the uncertainties in the estimation of the robot’s pose. The proposed approach allows robust long-term operations as it can recover the robot’s pose, even when it gets lost, to continue the map update process providing a coherent map. Moreover, the approach is robust also to temporary changes in the map due to the presence of dynamic obstacles such as humans and other robots. Results highlighting map quality, localisation performance, and pose recovery, both in simulation and experiments, are reported.

In this study, ignition delay and burning rate are experimentally investigated in relation to the effect of pristine carbon nanotubes (CNTs), sodium dodecylbenzene sulfonate (SDBS), and diesel blends. Single droplet combustion tests were conducted in a combustion system for 21 days using CNTs at concentrations of 50 ppm and 100 ppm, that were dispersed in Colombian commercial diesel and stabilized by SDBS. Additionally, recordings of the combustion were collected, and the Shadowgraph optical method was utilized for monitoring the evolution of droplet size during combustion. The measurements were done over a four-week period. The results demonstrated that the temporal stability has a direct impact on the single droplet combustion tests because a concentration of CNTs of 100 ppm showed higher stability than those achieved by 50 ppm. Consequently, improvements were found with a concentration of 100 ppm, for instance, thermal conductivity increased by about 20%, ignition delay time by 16.2%, and burning rate by 30.5%.

Thermal variations affect tri-trophic interactions involving plants, herbivores, and parasitoids, causing a mismatch between their phenological cycles. In the current environmental context of climate change, climatic factors can undergo profound and sudden changes, such as sudden hot or cold snaps. Here we show that episodes of short but sustained low temperatures have increased, mainly in the month of May, in the last two decades. We subjected galls induced by Asian chestnut gall wasp (ACGW) Dryocosmus kuriphilus to cold stress to assess if and how the pest and its parasitoids were affected. Over the course of two years seasonal parasitism, parasitism rates, the relative abundance of each parasitoid species, and mortality of ACGW were calculated. We found that the cold treatment affected both pest and parasitoids, resulting in a reduction in emerging ACGWs and differing ratios of species within the parasitoid community. The striking example was the change in the relative frequency of three species of Eupelmus spp. and of Mesopolobus tibialis, which doubled in thermally-stressed galls in all chestnut fields. The thermal effects on the development of the host and the direct effects of cold temperatures on the surface of galls (i.e., humidity or hardness of the galls) warrant further research in this direction.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Multicore magnetic nanoparticles of manganese ferrite were prepared using carboxymethyl-dextran and melamine as agglutinating agents. The nanoparticles prepared using melamine exhibit a flower-shape structure, a saturation magnetization of 6.16 emu/g and good capabilities for magnetic hyperthermia. Magnetoliposome-like structures containing the multicore nanoparticles exhibit sizes in the range 250 – 400 nm. A new antitumor thienopyridine derivative was loaded in these nanocarriers with a high encapsulation efficiency of 98% ± 2.6%. Release profiles in absence and presence of an AMF indicate a transport by diffusion, with a maximum compound release of 31% under the AMF. A sustained and controlled drug release in anticipated from the results, pointing to suitable characteristics of the magnetoliposomes for dual cancer therapy (combined magnetic hyperthermia and chemotherapy).

In tunnel excavation with boring machines, the tunnel face is supported to avoid collapse and minimise settlement. This article proposes the use of reinforcement learning, specifically the Deep Q-Network algorithm, to predict the face support pressure. The approach is tested both analytically and numerically. By using the soil properties ahead of the tunnel face and the overburden depth as the input, the algorithm is capable of predicting the optimal tunnel face support pressure, adapting to changes in geological and geometrical conditions.

The International System of Units (SI) was adopted in 1960 as a universal measuring system to be used for all areas of science. Sports Science papers have shown lots of inaccurate and inappropriate terms for quantification of athletes’ performance and the psychobiological responses to exercise (e.g., internal load). In biomechanics, external and internal loads are forces acting externally and internally, inducing stress and strain in the biological tissues. Therefore, the current review present simple proposals to correct the inappropriate terms: 1) do not use the term external load when referring to the assessment of exercise time, distance, displacement, speed, velocity, acceleration, torque, work, power, impulse, etc.; 2) do not use the term internal load when referring to the assessment of psychobiological stress markers (i.e., session rating of perceived exertion, heart rate, blood lactate, oxygen consumption, etc.); 3) do not use the term impulse when expressing other calculus than integrating force with respect to time, and neither strain, when expressing other phenomena than the body deformation. Instead, the term exercise intensity is universal and can be used to describe all forms of exercise. Finally, duration should precisely be described according to physical quantities (e.g., time, distance, displacement, speed, velocity, acceleration, force, torque, work, power, impulse, etc.) and the units accomplish by use of the SI. These simple quantifications can be performed for the exercises, sessions, microcycles, mesocycles and macrocycles of the athletes. Such standardization will provide a consistent and clear communication among sports scientists and all areas of science.

The increasing importance of batteries in the 21st century and the challenges posed by the anticipated growth in end-of-life batteries, particularly in Europe, are addressed. Projections indicate a significant increase in battery waste, with a specific focus on the recycling of black mass (BM)—a complex and hazardous byproduct of the battery recycling process. The research employs the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology to systematically analyze the hazardousness of BM derived from various types of batteries. The findings reveal the inherently hazardous nature of BM, classifying it under multiple hazardous properties (HPs) according to European regulations. The urgent need for a definitive legislative classification of the hazardousness of BM is emphasized, and the potential of innovative technologies and strategies to improve recycling performance while mitigating risks is highlighted. The research significantly contributes to understanding the complexities of BM recycling, providing a foundation for future advancements in this area and emphasizing the need for further exploration and economic feasibility analysis of recycling technologies.

The crystal structure of a polymorph of Glycyl-L-alanine HI.H2O was synthesized from chiral cyclic Glycyl-L-alanine dipeptide, known to show molecular flexibility in different environments. The space group is polar (P21) and therefore pyroelectricity and optical second harmonic generation properties are allowed by symmetry. We report a pyroelectric coefficient as high as 45 µC/m2K occurring at 345 K, one order of magnitude smaller than the semi-organic ferroelectric Triglycine Sulphate (TGS) crystal. Furthermore, the polymorph displays a nonlinear optical effective coefficient of 0.14 pm/V, around 14 times smaller than the value from a phase-matched inorganic Barium Borate (BBO) single crystal.

This research experiments with a sustainability assessment based on the Sustainable Development Goals (SDGs) of Agenda 2030 through a process of their territorialisation and implementation. This process enables the development of a Spatial Decision Support System (SDSS) that can be integrated with strategic environmental assessments in urban planning. The assessment takes place on the transversality of the sustainability concept by trying to consider together the three dimensions (environmental, social and economic) into a single assessment through the Spatial Sustainability Assessment Model (SSAM) by integrating Geographic Information Systems (GIS) and multi-criteria analyses. Economic development, social equity, and ecological integrity represent three common visions for rethinking peri-urban edges.

Wild rocket plants were cultivated in a plastic greenhouse into two independent sectors, one for soil-bound (SbS) cultivation and another equipped for soilless (ScS) cultivation systems. In both SbS and ScS, the crop was subjected to treatments consisting in a high-compared to a low-input fertilization program (HF and LF treatment, respectively). Water use efficiency (WUE) and partial factor productivity (PFP) for nutrients (N, P, K, Ca and Mg for ScS, and N for SbS) were measured. Rocket leaves, separated for cultivation system and fertilization program, collected at different cuts during the growing cycle, were cold stored at 10 °C until 16 d. At each sampling day (at harvest and during the storage), sensory parameters, respiration rate, dry matter, colour, electrolyte leakage, antioxidant activity, total phenols, total chlorophyll and ammonia content were evaluated. In ScS, the PFP for all nutrients supplied as fertilizers showed a significant increase with the LF treatment, with values higher than 30 % for N, K and Ca. As for the postharvest performance, rocket leaves cultivated in ScS showed better qualitative traits than those cultivated in SbS, as suggested by the lower values of ammonia content and electrolyte leakage recorded at the end of storage in samples grown in ScS. Moreover, in ScS, data showed a lower membrane damage in LF than HF rocket leaves. Finally, regarding total chlorophyll content, even if no effect of treatments was recorded in SbS, rocket cultivated in ScS, showed a better retention of this parameter applying LF than HF treatment. In addition to this, a PLS model (R2 = 0.7) able to predict the cultivation system, using as variables total chlorophyll content no-destructively measured, was implemented.

Automated charging technologies are becoming increasingly important in the electrification of heavy road freight transport, especially in combination with autonomous driving. This study provides a comprehensive analysis of automated charging technologies for electric heavy-duty vehicles (HDVs). It encompasses the entire spectrum of feasible technologies, including static and dynamic approaches, with each charging technology evaluated for its advantages, potentials, challenges, and technology readiness level (TRL). Static conductive charging methods such as charging robots, underbody-couplers or pantographs show good potential, with pantographs being the most mature option. These technologies are progressing towards higher TRLs, with a focus on standardization and adaptability. While static wireless charging is operational for some prototype solutions, it encounters challenges related to implementation and efficiency. Dynamic conductive charging through an overhead contact line or contact rails holds promise for high-traffic HDV routes with the overhead contact line being the most developed option. Dynamic wireless charging, although facing efficiency challenges, offers potential for seamless integration into roads and minimal wear and tear. Battery swapping is emerging as a practical solution to reduce downtime for charging, with varying levels of readiness across different implementations. To facilitate large-scale deployment further standardization efforts are required. The study emphasizes the necessity for continued research and development to enhance efficiency, decrease costs, and ensure seamless integration into existing infrastructures. Technologies that achieve this best will have the highest potential to significantly contribute to the creation of an efficiently automated and environmentally friendly transport sector.

Purpose: The goal of this article was to introduce a new technique for root coverage (RC), the Mixed-Thickness Tunnel access (MiTT), approaching a full-split design, showing the results obtained in a case series and demonstrating it step-by-step. Methods: Healthy individuals, non-smokers, and non-diabetics, who were diagnosed with gingival recession (GR) type 1 or 2 (RT1 or RT2). After all necessary evaluations, prophylaxis was performed 14 days before the surgical procedure. Then, after the basics clinical conduct and anesthesia, one or two vertical incision(s) on the mucosa (around 1-2 mm apical to the MGJ), lateral to the papilla base, were done. Initial detachment of the mucosa from the muscles (split design); it was permitted (but not mandatory) to do intrasulcular incisions; from the MGJ to coronal, subperiosteal access was done to raise the full-thickness tunnel. It must communicate up to the gingival sulcus area and the papilla’s base, keeping the papilla’s tip intact. A connective tissue graft was harvested, which was inserted through the linear incision or intrasulcularly. Interrupted sutures were done and may be used as adjunctive material. Results: Nine healthy individuals (7 females and 2 males) aged 19 and 43 years were enrolled. They were treated following the MiTT steps. There were four cases with a single GR, 2 patients with 2 teeth involved, and three with 3 or 4 GR. Seven cases were RT1 and two RT2. All RT1 cases achieved 100% RC, while the mean RC obtained for RT2 was around 80%. Conclusion: MiTT can be considered a more straightforward approach for minimally invasive surgical technique, which is a feasible option to treat RC with a high success rate, predictability, and esthetic preservation. There is a technical sensitivity to performing the full-split design procedure.

Chronic kidney disease (CKD) affects worldwide 8-16% of the population. In developed countries, the most important risk factors for CKD are diabetes, hypertension and obesity, calling into question the importance of educating and acting on lifestyles and nutrition. A balanced nutrition and supplementation can indeed support the maintenance of a general health status, including preservation of renal function, and help to manage and curb the main risk factors for renal damage. While the concepts of protein and salt restriction in nephrology are historically acknowledged, the role of some nutrients on renal health and the importance of nutrition as a preventative measure for renal care are less known. In this review, we provide an overview of the demonstrated and potential actions of some selected nutrients, nutraceuticals and xenobiotics on renal health and function. The effects on kidney of fibres, proteins, fatty acids, curcumin, steviol glycosides, green tea, coffee, nitrates, nitrites, and alcohol, both direct and indirect, in CKD and non-CKD condition, are reviewed here. In a view of a functional and personalized nutrition, understanding the renal and systemic effects of dietary components is essential since many chronic conditions and CKD are related to systemic dysfunctions such as chronic low-grade inflammation.

Patch antennas are compact, less complex, planar structures and therefore, widely used in small satellite missions for telecommand, data link, and intersatellite link, particularly in S- band and X- band. Improved performance of these patch antennas in terms of gain and compactness will di-rectly affect the communication efficiency of small satellite missions. Especially the coming IoT (Internet of Things) constellations require high gain and efficient antenna arrays. An optimization of single patch antenna elements is an important cornerstone for the missions. Therefore, the ef-fects of various antenna enhancement techniques, such as slotted ground plane, resistor and ca-pacitor integration, parasitic patch elements, are analyzed. These techniques were applied on a rectangular patch antenna with parameter variation to identify the optimal performances with respect to bandwidth, operating frequency, gain, polarization, and power flow. Finally, the techniques were combined to obtain an optimized antenna in terms of gain and compactness. The results were compared to a slotted reference antenna. For the scenario of a 2.4 GHz patch antenna, a gain optimization of 27 % (from 7.09 to 8.14 dBi) or size reduction of 52 % (from 96.04 to 46.2 cm²) could be achieved. Overall, our study revealed an effective way to increase the patch antenna performance, which can directly contribute to more efficient communication links and design of antenna arrays.

In recent years information and communication technologies (ICT) play a significant role in all aspects of modern society and impact socioeconomic development in sectors as education, administration, business, medical care and agriculture. The benefits of such technologies in agriculture can be appreciated only if farmers use them. In order to predict and evaluate the adoption of these new technological tools, the technology acceptance model (TAM) can be a valid aid. The paper measures the potential acceptance of an e-learning tool designed for EU farmers and agricultural entrepreneurs. Starting from a literature review of the technology acceptance model, by analyzing the most commonly used external variables in the fields of e-learning, Agriculture, and Virtual reality, the analysis shows that computer self-efficacy, individual innovativeness, computer anxiety, perceived enjoyment, social norm, content and system quality, experience and facilitating conditions are the most common determinants addressing technology acceptance. Furthermore, findings evidenced that the external variables have a different impact on the two main beliefs of the TAM Model, Perceived Usefulness (PU) and Perceived Ease of Use (PEOU). This study is expected to bring theoretical support for academics when determining the variables to be included in TAM extensions.

Several coatings configurations of combined aluminizing and diffusion layered aluminide on 316 steel were produced and characterized. These coatings, typically employed as thermal barrier coating (TBC), can also be effective as vibration reduction elements at intermediate and high temperatures. This preliminary work has been focused on the microstructural design and processing effects of the coatings. The damping of the produced specimens was measured up to 450°C and compared with that of the steel substrate. The most performing coatings contain an Al-Si layer and exhibit a steep damping increase above 200 °C, reasonably due to dislocation movements by plastic straining of soft alloy layer and to the interface sliding between layers with different elastic moduli.

Coronavirus disease 2019 (COVID-19) is a potentially serious acute respiratory infection caused by the Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2). Since the World Health Organization (WHO) declared COVID-19 a global pandemic, the virus has spread to more than 200 countries with more than 500 million cases and more than 6 million deaths reported globally. It has long been known that viral respiratory tract infections predispose patients to bacterial infections and that these co-infections often have an unfavourable clinical outcome. Moreover, nosocomial infections, also known as health care-associated infections (HAIs), are those infections that are absent at the time of admission and acquired after hospitalization. However, the impact of coinfections or secondary infections on the progression of COVID-19 disease and its lethal outcome is still debated. The aim of this review was to assess the literature on the incidence of bacterial co-infections and superinfections in patients with COVID-19. The review also highlights the importance of the rational use of antibiotics in patients with COVID-19 and the need to implement antimicrobial stewardship principles to prevent the transmission of drug-resistant organisms in healthcare settings. Finally, alternative antimicrobial agents to counter the emergence of multidrug-resistant bacteria causing healthcare-associated infections in COVID-19 patients will also be discussed.

Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

The purine nucleoside analogues cladribine and pentostatin are highly-active first-line therapeutic treatments for hairy cell leukemia (HCL), resulting in complete response rates of 80 to 90%. However, HCL patients continue to relapse, and sooner or later, most require subsequent lines of treatment. This report presents the relapsed patients with classic HCL who were treated with vemurafenib (mostly at the low dose of 240 mg twice daily for 16 weeks) combined with rituximab after the failure of several lines of therapy including cladribine with or without rituximab and moxetumomab pasudotox. Two patients achieved CR MRD (-) after combined treatment with vemurafenib and rituximab, with a hematologic response ongoing after 38 months from the end of treatment in one patient and a relapse of cytopenias occurring after 13 months in the other patient. A third patient normalized her blood counts and this hematologic response, which was not evaluated in the bone marrow at the end of treatment, was lost after 18 months. The last patient died due to infection and multi-organ failure, too early to verify response to vemurafenib. Two patients who had relapsed after vemurafenib and rituximab derived meaningful clinical benefit from retreatment with the same agents, but eventually relapsed again and started indefinite therapy with dabrafenib and trametinib with normalization of the blood counts despite heavy bone marrow infiltration in the only patient so far evaluable. The outcomes of these cases indicate that novel targeted agents, and in particular vemurafenib combined with rituximab, improve the prognosis of HCL patients, even those heavily pretreated with PNAs and moxetumomab pasudotox

Starting from the environmental issues related to global warming, climate change and reduction of greenhouse gas emissions, this review paper describes how CO₂ recycling can represent a challenging strategy suitable to explore new concepts and opportunities for catalytic and industrial development. In this view, the production of dimethyl ether (DME) from catalytic hydrogenation of CO₂ appears as a viable technology, able to meet also the ever-increasing need for alternative environmentally-friendly fuels and energy carriers. Basic considerations on thermodynamic aspects controlling DME production from CO₂ are presented, then summarizing the main catalytic systems developed in such a field. Special attention is paid on the role assumed during last years by zeolite-based systems, either in the methanol-to-DME dehydration step or in the one-pot CO₂-to-DME hydrogenation. On the whole, the productivity of DME results significantly to be dependent on several catalyst features, linked not only to the metal-oxide phase responsible for CO₂ activation/hydrogenation, but also to specific properties of the zeolites (i.e., topology, porosity, surface area, acidity, interaction with active metals, distributions of metal particles, …) influencing activity and stability of hybridized bifunctional heterogeneous catalysts.

Salting influences microbial growth, enzymatic activity and biochemical reactions during ripening, thus contributing to the final quality of cheese. The aim of this study was to evaluate the influence of different salting methods (dry salting at 12, 24 and 48 h; in brine; and curd salting) on the chemical (moisture and salt content), physico-chemical (pH, titratable acidity and water activity) and sensory (texture profile analysis, colour and sensory attributes) characteristics of an industrial blue vein cheese. Dry salted cheeses had lower moisture content and water activity, and higher salt/moisture content and acidity than those salted in brine and curd. Dry-salted cheeses were also characterised by higher values for hardness, fracturability and instrumental gumminess. Dry-salted cheeses showed differences only in the red/green colour component (a*), with the curd-salted cheeses being less greenish. All cheeses scored high (around 7) in the tasters' overall impression, with the dry-salted cheeses at 12 and 24 h showing optimal growth and even distribution of mould, as well as better flavour and texture.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

N,N-dimethyl-4-nitroaniline (NNDM4NA, C8H10O2N2), is a superelastic and superplastic charge-transfer molecular crystal with a high molecular dipole moment, µ=7.95 D, which crystal-lizes in the acentric polar point group 2. Highly aligned poly-l-lactic acid (PLLA) polymer micro-fibers with embedded NNDM4NA nanocrystals were fabricated using the electrospinning tech-nique. The composite fibers display an extraordinarily high piezoelectric output response, where for a small stress of 5.0x103 Nm-2, an effective piezoelectric voltage coefficient of geff=3.6 VmN-1 was obtained. The fibers were found to display solid state blue fluorescence with a long (147 ns) life-time decay. Furthermore, the composite fibers exhibit an average increase of 67% on the Young modulus reaching 55 MPa, while the tensile strength reaches 2.8 MPa when compared with solely PLLA fibers. The results show that nanocrystals, from small organic molecules, with elastic and piezoelectric properties form hybrid functional 2-dimensional luminescent array which are me-chanical strong and generate high output voltages making them promising for applications in energy harvesting and as solid-state blue emitters.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

The aim of this study was to evaluate implants survival rate, marginal bone loss, surgical and prosthetic complications of implants placed through sinus floor elevation and tilted implants en-gaged in basal bone in order to bypass maxillary sinus. 60 patients were enrolled for this study. According with residual bone height of posterior maxilla the sample was divided in three groups of 20 patients: Group A (lateral sinus floor elevation), Group B (transrectal sinus floor elevation) and Group C (tilted implants employed to bypass sinus floor). Follow-up visits were performed one week after surgery, at 3, 6 months and then once a year for next 4 years. The outcomes were implants survival rate, marginal bone loss and surgical and prosthetic complications. Although the Group A, B and C have demonstrated an implants survival rate of 83.3%, 86,7% and 98,3% respectively, the statistically analysis showed that there was no statistically significant difference between groups. Statistically significant differences between the groups were also not found con-cerning marginal bone loss, as recorded by intra-oral X-ray measurements during follow-up. About complications it wasn’t possible to perform a statistical analysis. To as to reduce potential surgical risks implants placement in basal bone should be preferred.

This case report utilized the primary data gathered from the extension program of the LORMA College of Medical Laboratory Science at the institution’s adopted locale. Arosip is a secluded, difficult-to-reach mountainous barangay in the municipality of Bacnotan, in the province of La Union, Philippines. The study subjects were forty-one (41) kindergarten to grade three students of Arosip Elementary School. Modified Kato-Katz technique was performed to the submitted stool samples. Among 41 participants, nine were screened positive for the helminthic ova of Ascaris lumbricoides, and Trichuris trichiura – yielding a total of 21.95% prevalence rate. Among those 9 participants, 6 (66.67%) were positive for Ascaris lumbricoides ova, and 3 (33.33%) were co-infected with both Ascaris lumbricoides and Trichuris trichiura ova. The findings were relayed and reported to the local government unit. The team recommends for a more comprehensive screening and monitoring of STH cases in the locale, a continuous stewardship of health programs including mass-deworming for the school children and awareness campaigns, and provision of health resources. Ultimately, interagency collaboration between the Department of Health, Department Education, and Local Government Unit remains highly warranted to satisfy the health inequities experienced by this disadvantaged remote community.

Prediction markets are heralded as powerful forecasting tools, but models to describe them often fail to capture the full complexity of the underlying mechanisms that drive price dynamics. To address this issue, we propose a model in which agents belong in a social network, have an opinion about the probability of a particular event to occur, and bet on the prediction market accordingly. Agents update their opinions about the event by interacting with their neighbours in the network, following the Deffuant model of opinion dynamics. Our results suggest that a simple market model that takes into account opinion formation dynamics is capable to replicate the empirical properties of historical prediction market time series, including volatility clustering and fat-tailed distribution of returns. Interestingly, the best results are obtained when there is the right level of variance in the opinions of the agents. Moreover, this paper provides a new way to indirectly validate opinion dynamics models against real data by using historical data obtained from PredictIt, an exchange platform whose data has never been used before to validate models of opinion diffusion.

X-ray fluorescence is largely employed in the measurement of the thickness of coatings. Despite of its diffusion, the task is not straightforward because of the complex physics involved that results in high dependence on matrix effects. Thickness quantification is in practice accomplished using the Fundamental Parameters approach, adjusted with empirical measurements of standards with known composition and thickness. This approach has two major drawbacks: i) there are no standards for any possible coating and coating architecture and ii) even relying on standards, the quantification of unknown samples requires the precise knowledge of the matrix nature (e.g., in case of multilayer coatings the thickness and the composition of each underlayer). In this work, we describe a semiquantitative approach to coatings thickness measurement based on the construction of calibration curves through simulated XRF spectra built with Monte Carlo simulations. Simulations have been performed with the freeware software XMI-MSIM. We have assessed the accuracy of the methods by comparing the results with those obtained by i) XRF thickness determination with standards and ii) FIB-SEM cross-sectioning. Then we evaluated which parameters are critical in this kind of indirect thickness measurements.

In this paper, a multibody calculation methodology has been applied to the vibration analysis of a 4-cylinder, 4-stroke, turbocharged diesel engine, with a simulation driven study of the angular speed variation of a crankshaft under consideration of different modeling assumptions. Moreover, time dependent simulation results, evaluated at the engine supports, are condensed to a vibration index and compared with experimental results, obtaining satisfactory outcomes. The modal analysis also considers the damping aspects and has been conducted using a multibody model created with the software AVL/EXCITE. The influence of crankshaft torsional frequencies on the rotational speed behavior has been evaluated in order to reduce the vibration phenomena.

Anthropogenic disturbances interacting with natural disturbances, ecological and socio-economic factors can provoke forest degradation and modulate ecosystem resilience. In Haiti, protected areas recently created to reduce forest loss, require studies about forest dynamics and land use to assure the development of sustainable management policies. We combine field interview with Landsat satellite images of the Macaya National Park collected between 1985 and 2021 to investigate: 1) how much of the original forest area has been converted into agricultural or logged area since 1985; and 2) how do elevation and slope influence the expansion of human-induced land-use changes. Our results indicate an increase of 11.36% in forest cover and a reduction of 75.34% in agriculture class cover, despite the passage of seven hurricanes in the region. Forest recovery was apparently unrelated to elevation and slope, and likely reflected the implementation of new environmental laws and policies with the creation of the Macaya National Park in 1983. Restoration and protection programs contributed to ensure access to financial resources, technical assistance and new technology, thus promoting a shift into a more resilient forest system. This study brings hope for forest conservation in Haiti by showing that positive results can be achieved through inclusive collaboration.

This paper presents an analysis of future precipitation patterns over the Lake Victoria Basin using bias-corrected CMIP6 model projections. A mean increase of about 5% in mean annual (ANN) and seasonal [March-May (MAM), June-August (JJA), and October-December (OND)] precipitation climatology is expected over the domain by mid-century (2040-2069). The changes intensify towards the end of the century (2070-2099) with an increase in mean precipitation of about 16% (ANN), 10% (MAM), and 18% (OND) expected, relative to the 1985-2014 baseline period. Additionally, the mean daily precipitation intensity (SDII), the maximum 5-day precipitation values (RX5Day), and the heavy precipitation events, represented by the width of the right tail distribution of precipitation (99p-90p) show an increase of 16%, 29%, and 47%, respectively, by the end of the century. The projected changes have a substantial implication for the region - which is already experiencing conflicts over water and water-related resources.

Worldwide anthropogenic activities result in the production and release of poten-tially damaging toxic pollutants into ecosystems, thereby jeopardizing their health and continuity. Research studies and biomonitoring programs attend to this emerging problematic by applying and developing statistically relevant indexes that integrate complex biomarker response data to provide an holistic approach reflecting toxically induced alterations at the organism’s or population level. Ultimately, indexes allow simple result communication, enhancing policy makers understanding, so contributing for better resource and environmental managing policies. In this study three indexes , the Integrated Biomarker Response index (IBR), the Bioeffects Assessment Index (BAI) and the Principal Components Analysis (PCA), were evaluated for their sensitivity in revealing toxically induced stress patterns in cells of the diatom Phaeodactylum tricornutum under contaminant exposure. The set of biomarkers selected for index construction comprise the anti-oxidant enzymes APX, CAT and SOD, and the lipid peroxidation marker TBARS. Several significant inverse correlations with the concentration gradients applied, , was noticed for all indexes, though, the IBR excels for its reliability in delivering statistically significant dose-response patterns for four out of the five compounds tested.

Obsessive–compulsive disorder (OCD) is believed to follow a waxing and waning course, often according to environmental stressors. During the COVID-19 pandemic, pre-existing OCD symptoms were reported to increase and to change from checking to washing behaviors, while new-onset symptoms were predominantly of the hoarding type. In the present study, we followed the evolution of OCD symptoms, anxiety, depression, and insight of illness in forty-six OCD patients throughout the pandemic. Clinical measures were collected at four different time points before and during the COVID-19 pandemic in Italy. Within-subject comparisons were used to compare clinical scale scores across time, and correlations were examined between patients' baseline characteristics and changes in clinical scores. We found that all clinical measures increased during the first Italian lockdown, with respect to the pre-pandemic values. Anxiety decreased during the temporary elimination of restriction provisions, whereas severity of OCD symptoms and insight returned to pre-pandemic values during the second mandatory lockdown. These results were observed only in two sub-groups of patients: those taking benzodiazepines and those with shorter illness duration. Our findings suggest the need of additional clinical attention to these specific sub-groups of OCD patients in case of particularly distressing circumstances, while pointing to a possible adaptive role of their OCD symptoms when the environment requires a higher care of hygiene and extraordinary supply of essential resources.

The global agricultural sector is increasingly pressured to adopt sustainable practices and reduce its environmental impact. In this context, greenhouses play a crucial role in enabling year-round crop production, ensuring food security, and minimizing reliance on traditional open-field farming. However, the energy consumption associated with greenhouse operations poses a significant challenge to achieving sustainability goals. As a result, there is a growing emphasis on transitioning greenhouses towards near-zero energy consumption. Near-zero energy consumption in greenhouses refers to the ambitious objective of minimizing energy usage to the greatest extent possible while maintaining optimal growing conditions for crops. This goal encompasses reducing energy consumption for heating, cooling, lighting, and other operational needs, as well as exploring renewable energy sources to power greenhouse operations. This review article offers a comprehensive overview of greenhouse energy consumption, with the main goal of analyzing the present situation, identifying key challenges, exploring potential opportunities, and proposing future perspectives for decreasing energy usage in greenhouse environments. As the focus on sustainable agricultural practices grows, the need to reduce energy consumption in greenhouses becomes increasingly important. The review critically examines current technological models and strategies applied in smart greenhouse applications, as well as the monitoring of microclimatic conditions inside the greenhouse, encompassing factors such as temperature, humidity, CO2 levels, soil quality, and crop cultivation. Moreover, it aims to present existing literature that investigates the advancement of greenhouses toward achieving significant reductions in energy consumption.

Soft robotic manipulators consisting of serially-stacked segments combine actuation and structure in an integrated design. This design can be miniaturised while providing suitable actuation for applications such as minimally invasive surgery and for inspections in confined environments. The control of these robots, however, remains challenging, due to the difficulty in accurately modelling the robots, in coping with their redundancies, and in solving their full inverse kinematics. In this work, we explore a hybrid approach to control serial soft robotic manipulators that combines machine learning (ML) to estimate the inverse kinematics with a closed-loop control to compensate the remaining errors. For the ML part, we compare various approaches, including both kernel-based learning and more general neural networks. We validate the selected ML model experimentally. For the closed-loop control part, we first explore Jacobian formulations using both synthetic models and numerical approximations from experimental data. We then implement integral control actions using both these Jacobians, and evaluate them experimentally. In an experimental validation, we demonstrate that the hybrid control approach achieves setpoint regulation in a robot with 6 inputs and 4 outputs.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

Objective: The primary objective of this trial was to assess the transfer of drospirenone to breast milk after daily administration of an oral test preparation containing 4 mg of drospirenone at the steady state. The secondary objective of the trial was to assess the safety of the preparation based on safety clinical and laboratory measurements (at the beginning and at the end of the trial) and reporting of adverse events and/or adverse drug reactions. Patients and Methods: This was an open label, non-comparative single center study. Drospirenone 4mg per day was the first postpartum contraceptive for the study participants who were no longer breastfeeding yet were still lactating. It was administered for 7 (seven) days to achieve steady-state concentration. All participants were volunteers who planned to use oral contraceptives as their family planning method in the future. Results: A total number of 12 volunteers completed the trial according to the protocol and the samples of all the 12 study completers were analyzed. The average concentration-time curve of drospirenone in plasma 24 h after the administration of the last dose (AUC(0-24h)) was 635.33 ng*h/mL and 120 h after the single repeat dose administration (AUC(0-120h) was 1180.57 ng*h/mL, respectively. The average Cmax was 48.64 ng/mL. The average concentration-time curve of drospirenone in milk 24 h after the administration of the last dose (AUC(0-24h)) was 134.35 ng*h/mL and 120 h after the single repeat dose administration (AUC(0-120h) was 227.17 ng*h/mL respectively. The average Cmax was 10.34 ng/mL. Conclusion: On average 18.13% of plasma drospirenone made it to breast milk and the highest concentration of drospirenone in breast milk was 17.55% of that in plasma. The total quantity of drospirenone passing to breast milk is on average 4478 ng during a 24 h period representing 0.11% of the maternal daily dose. Thus, at the recommended doses, no effects on breastfed newborns/infants are anticipated with drospirenone 4 mg.

Bettelmatt cheese, a cherished Italian culinary gem hailing from the picturesque Val d'Ossola region, is deeply intertwined with its natural environment. This article explores the intricate relationship between the organoleptic attributes of Bettelmatt cheese and the challenges posed by climate change. The sensory qualities of this cheese, including its flavor profile, texture, and aroma, are profoundly influenced by the alpine pastures where the cows graze, the unique terroir, and the traditional production methods. However, as climate change continues to impact ecosystems and weather patterns, it raises questions about the resilience and adaptability of this traditional cheese. In addition to these challenges, the article would like to explore the complexities of regulation and protection of this cheese, crucial for food and gastronomic sciences.

The review of previous works shows this study is the first attempt to analyse the lockdown effect using Natural Language Processing Techniques, particularly sentiment analysis methods applied at large scale. On the other hand, it is also the first of its kind to analyse the impact of COVID 19 on the university community jointly on staff and students and with a multi-country perspective. The main overall findings of this work show that the most often related words were family, anxiety, house and life. On another front, it has also been shown that staff have a slightly less negative perception of the consequences of COVID in their daily life. We have used artificial intelligence models like swivel embedding and the Multilayer Perceptron, as classification algorithms. The performance reached in terms of accuracy metric are 88.8% and 88.5%, for student and staff respectively. The main conclusion of our study is that higher education institutions and policymakers around the world may benefit from these findings while formulating policy recommendations and strategies to support students during this and any future pandemics.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

Background: the study aimed at comparing the prognostic importance of Heart Rate (HR) and of QT corrected (QTc) according to Fridericia, Framingham and Bazett methods, in a large non-selected population. Methods: the analysis of digital Electrocardiograms archived from 2008 to 2022 in the metropolitan area of Modena, Italy, was made. The population under study was divided into three age-groups and survival analysis was performed. Results: 131.627 patients were enrolled and during the follow-up (mean 1641.4 days), all-cause mortality was 8.9%. Both HR and QTc were associated with mortality. All-cause mortality significantly increased from HR values greater than 81 BPM and from QTc values greater than 440 msec in young subjects and 455 msec in old subjects (values of the 75th percentiles/optimal operating point). Cox analysis confirmed the better prognostic value of Bazett’s QTc and of HR in the whole population and in the three age-groups. Conclusion: Bazett’s method performed better than other methods but unexpectedly HR had the same or a better correlation with all-cause mortality. Since HR is simple and readily available, its evaluation should be improved. However, reference values for QTc and for HR are difficult to define causing many confounding factors and further population-study are required.

Since the beginning of coronavirus disease 2019 (COVID-19) pandemic, large attention has been focused on the relationship between SARS-CoV-2 diffusion and environment. As a matter of fact, clear evidence of the transmission of SARS-CoV-2 via respiratory aerosol would be of primary importance; at the same time, checking the presence of SARS-CoV-2 in wastewater can be extremely useful to control the diffusion of the disease. Up to now, many studies report SARS-CoV-2 concentrations in indoor/outdoor air samples or water/wastewater samples that can differ by order of magnitude. Unfortunately, complete information about the scientific approach of many studies is still missing, relating to: samplers and sampling materials performances, recovery tests, measurement uncertainty, robustness, detection and quantification limits, infectivity of captured virus, virus degradation during sampling, influence of sample pre-treatments (included freezing) on results, effects of inhibitors, sample alterations due to manipulation, validation of methods and processes, quality assurance according to ISO/IEC 17025 requirements.Based on the first experiences focused on the presence of SARS-CoV-2 in environmental samples such as air quality filters, air-liquid impingers and wastewater samples, the present study describes a coherent preliminary approach to SARS-CoV-2 environmental sampling in order to overcome the evident lack of standardization. Three aspects are highlighted here: the first solution to assure quality and consistency to environmental sampling relies on the development of recovery tests using standard materials and investigating sampling materials, sampling techniques, sampling durations, sample conservation and pre-treatments; secondly, in order to overcome the shortcomings of every single sampling technique, coupling different samplers in parallel sampling could be an efficient strategy to collect more information and make data more reliable, in particular for air samples; finally, with regards to airborne virus sampling, the results could be confirmed by simplified emission and dilution models.

This study investigated the influence of land-use and precipitation change and variability on Lake Victoria’s water-level fluctuations. Extreme precipitation events, corresponding to extreme water-levels, over the lake and its catchment area were identified and their return periods estimated by fitting them into a generalized extreme value (GEV) distribution. Using general circulation models from the 6^th phase of the Coupled Model Intercomparison Project (CMIP6)’s Detection & Attribution Model Intercomparison Project (DAMIP), an assessment of the potential contribution of human-induced climate change on the observed precipitation patterns over the study area was done. The greatest precipitation anomalies for the period 1900-2020 were recorded in 1961’s October-December (OND) season and 2019’s June-August (JJA) and OND seasons, corresponding to the period when the highest water-levels were recorded in Lake Victoria. While land-use change in the study domain was observed, extended and unusually heavy June to December 2019 precipitation bore the greatest responsibility for the 2019/2020 high water-levels in Lake Victoria. The OND precipitation event of 2019 was a 1-in-52-year event compared to the 1961’s 1-in-693 years. Differences in return periods at various parts of the lake imply a high spatial climate variability within the lake itself. An analysis of the fraction of attributable risk (FAR) showed natural variability to have a greater influence on the JJA and OND precipitation patterns over Lake Victoria than human-induced climate change. However, variability over the land area of the study domain was mainly driven by human-induced climate change rather than natural variability, implying a unique climate system over Lake Victoria. Findings from the current study enhance the understanding of Lake Victoria’s water budget and motivate for further research to inform effective strategies on the planning and use of Lake Victoria’s water resources in a changing climate.

Despite increased hurricane intensity, the U.S. Gulf of Mexico coast has experienced dramatic coastal population increase of 24.5% from 2000 to 2016. However, in coastal Louisiana areas with dramatic wetland loss, parishes have experienced population declines and lower rates of population growth. Therefore, understanding the magnitude of the effect of wetland loss as a main driver in population loss in coastal Louisiana is critical. Using regression analysis, this study finds that wetland loss has a significant and persistent negative effect on population growth in coastal Louisiana. This effect resulted in a reduction in the population growth rate in coastal parishes over time. A counterfactual simulation was conducted to estimate the potential population size in the absence of wetland loss from 1990 to 2021. On average, the effect of 1 hectare of wetland lost causes a reduction of approximately 1000 persons. This indicates that for the year 2021, the population was approximately 18% lower than the population that would have existed in the absence of wetland loss. This research underscores the role of wetlands in providing direct and indirect benefits to people in coastal Louisiana that are ultimately reflected in its population levels.

This study proposes a machine-learning-based framework for detecting mechanical damage in pipelines, utilizing physics-informed datasets collected from simulations for mechanical damage. The framework provides an effective workflow from dataset generation to damage detection and identification for three types of pipeline events: welds, clamps, and corrosion defects. While the study initially focused on optimizing the CNN structure using various advanced optimizers, it also investigated the impact of sensing systems on data classification and the effect of noise on classification performance. The study's analysis highlights the importance of selecting the appropriate sensing system for the specific application. The authors also found that the proposed framework is robust to experimentally relevant levels of noise, suggesting its applicability in real-world scenarios where noise is present. Overall, this study contributes to the development of a more reliable and effective method for detecting mechanical damage in pipelines. The proposed framework provides an effective workflow for damage detection and identification, and the findings on the impact of sensing systems and noise on classification performance add to its robustness and reliability.

The use of modulator drugs that target the cystic fibrosis transmembrane conductance regulator (CFTR) is the final frontier in the treatment of Cystic Fibrosis (CF), a genetic multiorgan disease. F508del is the most common mutation causing defective formation and function of CFTR. Elexacaftor-tezacaftor-ivacaftor is the first triple combination of CFTR modulators. Herein we report on a one-year case-control study that involved 26 patients with at least one F508del mutation. Patients were assigned to two similar groups, with patients with the worse clinical condition receiving treatment with the triple combination therapy. The study aims to define the clinical and especially microbiological implications of treatment administration. The treatment provided significant clinical benefits in terms of respiratory, pancreatic and sweat function. After one year of therapy, airway infection rates decreased and pulmonary exacerbations were dramatically reduced. Finally, treated patients reported a surprising improvement in their quality of life. The use of triple combination therapy has become essential in most CF people carrying the F508del mutation. While the clinical and instrumental benefits of treatment are thoroughly known, further investigations are needed to properly define its microbiological respiratory implications and establish the real advantage of life-long treatment with elexacaftor-tezacaftor-ivacaftor.

The redox chemistry of copper(II) is strongly modulated by the coordination to amyloid-β peptides and by the stability of the resulting complexes. Amino terminal copper and nickel binding motifs (ATCUN) identified in truncated Aβ sequences starting with Phe4 show very high affinity for copper(II) ions. Herein, we study the oxidase activity of [Cu-Aβ4-x] and [Cu-Aβ1-x] complexes toward dopamine and other catechols. The results show that the CuII-ATCUN site is not redox-inert, the reduction of the metal is induced by coordination of catechol to the metal and occurs through an inner sphere reaction. The generation of a ternary [CuII-Aβ-catechol] species determines the efficiency of the oxidation, although the reaction rate is ruled by re-oxidation of the CuI complex. In addition to the N-terminal coordination site, the two vicinal histidines, His13 and His14, provide a second Cu-binding motif. Catechol oxidation studies together with structural insight from the mixed dinuclear complexes Ni/Cu-Aβ4-x reveal that the His-tandem is able to bind CuII ions independently of the ATCUN site, but the N-terminal metal complexation reduces the conformational mobility of the peptide chain, preventing the binding and oxidative reactivity toward catechol of CuII bound to the secondary site.

BACKGROUND: Endoscopic placement of Self Expandable Metal Stents to relieve malignant colorectal obstruction has become a common therapeutic advancement in clinical practice. MATERIAL: In a 16 year period 167 patients had endoscopic placement of a Self Expandable Metal Stent in a center where gastroenterologists and surgeons cooperate in a daily basis, discussing indications. RESULTS: There was no operative mortality and no major complication in placement of the stent. Technical and clinical success was respectively 95.1% and 92.9%. Consultation among specialists changed the preoperative indication in 60 patients, during the same time period. CONCLUSIONS: Self expandable metal stents placement represents an important tool to treat patients with obstructing colorectal cancer and complications after colorectal resection . A proper training is required, and this training in operative endoscopy is not always available and possible. In this scenario, a close collaboration among specialists in selecting the most appropriate operative procedure is essential and brings to better results.

Background: to know the existing documentation related to exogenous melatonin in the performance of professional soccer players. Methods: critical and systematic review. Data were obtained by looking up the following bibliographic data bases: Web of Science, MEDLINE (via PubMed), Embase, Cochrane Library and Scopus. The used terms were "Soccer Athlete", "Melatonin" and "Soccer Performance", using as a filter: "Humans". The search update was in May 2023. Results: having applied the inclusion and exclusion criteria, 8 articles were selected out of 59 retrieved references. The dose of melatonin administered in the studies ranged between 5 and 8 mg. The outcomes showed a decrease in oxidative stress, muscle damage and inflammatory markers in the melatonin-treated group. Conclusions: Exogenously administered melatonin seems to attenuate some of the effects derived from physical exercise such as oxidative stress, inflammation and muscle damage in professional soccer players, and since it has no potential adverse effects, it could be interesting to apply it in this population. However, the direct effects of melatonin supplementation on physical performance have not been demonstrated, so more research is needed on the intervention period, effective dose and larger participant populations.

Knowledge of body composition is essential for athletes for their sport performance. It has yet to be determined whether differences in body composition are present between international and non-international players playing in the same elite professional club competition. Similarly, it is not yet clear whether differences in body composition according to ethnic origin exist in the elite professional game, where relative homogeneity is to be expected among soccer players. There is no single anthropometric profile that guarantees sporting success, as the somatotype of football players differs according to their individual characteristics. The aim of this study was to assess the description and comparison of the body composition profile of latin american professional football players playing in european leagues. The sample was composed of 238 subjects football players from European professional football leagues. Differences were found in all variables measured. The present study shows that in Latin American professional football players playing in Europe, there are significant differences in different body composition variables such as weight, height, WC, skinfold and fat values. This means that the treatment of these data and the possible classifications of sporting performance carried out in football clubs should be different to other European or African-American football players.

The CRISPR-Cas9 system is an emerging therapeutic tool with the potential to correct diverse ge-netic disorders. However, for gene therapy applications an efficient delivery vehicle is required, capable of delivering the CRISPR-Cas9 components into the cytosol of the intended target cell population. Once there, the ribonucleoprotein complex (RNP) can be transported into the nucleus. Lipid nanoparticles (LNP) serve as promising candidates for delivery of CRISPR-Cas9 RNP. These delivery vehicles have been optimized for the delivery of nucleic acids, such as mRNA. Co-delivery of Cas9 encoding mRNA with the accompanying sgRNA leads to translation of the Cas9 protein and formation of the Cas9 RNP inside the cell. Only recently, direct delivery of the CRISPR-Cas9 RNP complexes has been explored, which requires adjustments to the LNP formulation. In this study, the importance of buffer composition and cationic charge during RNP and ssDNA en-trapment in LNP are demonstrated. After optimizing several formulation parameters, LNP were prepared that were colloidally stable in human plasma and efficiently deliver the SpCas9 RNP and ssDNA for HDR-correction in reporter cells. Under optimal formulation conditions, gene knock-out and gene correction efficiencies as high as 80% and 20%, respectively were achieved at nanomolar CRISPR-Cas9 RNP concentrations.

Although COVID-19 primarily affects the respiratory system, it can have various effects on other organs, including the cardiovascular system. COVID-19 can lead to a prothrombotic status, promoting bloodclotting, which can potentially affect native vessels and implanted de-vices. The exact mechanisms by which it leads to increased clotting are not yet fully understood but may involve inflammation, endothelial dysfunction, and a hyperactive immune response. In the present report, we describe a case of an acute aortic stent-graft thrombosis four days after resolution of Sars-Cov2 infection. The patient required emergent explantation of the stent-graft, after the failure of endovascular bailout procedures.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

Myocastor coypus is a pest animal present in Africa, Europe, North America, and Asia that causes agricultural and ecological damages. Moreover, it has to be considered as a potential risk for public health. Forty-four Nutrias from the “Parco Naturale La Mandria” (Piedmont region, Northwest Italy) have been analysed. A complete necropsy and a whole histological evaluation of liver, kidney and lung have been carried out on all the animals. Moreover, the positivity to Hepatitis E Virus (HEV), Encephalomyocarditis virus (EMCV), Francisella spp., Toxoplasma gondii and Neospora caninum have been investigated. None of the animal resulted positive for HEV, EMCV, Francisella spp. or Neospora caninum. Two animals tested positive for Toxoplasma gondii. A high presence of histological lesions has been identified in different organs, suggesting that lesions could be induced by different pathogens. As previously reported, Nutria can act as a host for several pathogens, including important agents for human and animal health, and surveillance is necessary, to fully understand the biological role and the importance of coypu as a disease reservoir in our country.

Riboflavin transporter deficiency (RTD) is a childhood-onset neurodegenerative disorder characterized by sensorineural deafness and motor neuron degeneration. Since riboflavin plays key functions in biological oxidation-reduction reactions, energy metabolism pathways involving flavoproteins are affected in RTD. We recently generated iPSC lines from affected individuals as an in vitro model of the disease and documented mitochondrial impairment in these cells dramatically impacting cell redox status. In the present work, we extend our study to motor neurons (MNs), i.e., the cell type mostly affected in patients with RTD. Altered intracellular distribution of mitochondria was detected by confocal microscopic analysis, following immunofluorescence for superoxide dismutase 2 (SOD2), as a dual mitochondrial and antioxidant marker, and βIII Tubulin, as neuronal marker. We demonstrate significantly lower SOD2 levels in RTD MNs, as compared to their healthy counterparts. Mitochondrial ultrastructural abnormalities were also assessed by Focused Ion Beam/Scanning Electron Microscopy. Moreover, we investigated the effects of combination treatment using riboflavin and N-acetylcysteine, which is a widely employed antioxidant. Overall, our findings further support the potential of patient specific RTD models, and provide evidence of mitochondrial alterations in RTD-related iPSC-derived MNs, emphasizing oxidative stress involvement in this rare disease. We also provide new clues for possible therapeutic strategies, aimed at correcting mitochondrial defects, based on the use of antioxidants.

We addressed the frequent occurrence of mixed-chain lipids in biological membranes and their impact on membrane structure by studying several chain-asymmetric phosphatidylcholines and the highly asymmetric milk sphingomyelin. Specifically, we report trans-membrane structures of the corresponding fluid lamellar phases using small-angle X-ray and neutron scattering, which were jointly analyzed in terms of a membrane composition-specific model, including a headgroup hydration shell. Focusing on terminal methyl groups at the bilayer center we found a linear relation between hydrocarbon chain length mismatch and the methyl-overlap for phosphatidylcholines, and a non-negligible impact of the glycerol backbone-tilting, letting the sn1-chain penetrate deeper into the opposing leaflet by half a CH2 group. That is, penetration-depth differences due to the ester-linked hydrocarbons at the glycerol backbone, reported previously for gel phase structures also extend to the physiological more relevant fluid phase, but are significantly reduced. Moreover, milk sphingomyelin was found to follow the same linear relationship suggesting a similar tilt of the sphingosine backbone. Complementary performed molecular dynamics simulations revealed that there is always a part of the lipid tails bending back, even if there is a high interdigitation with the opposing chains. This suggests that hydrocarbon chain interdigitation plays only a minor role in transbilayer coupling. For both cases of adaption to chain length mismatch, chain-asymmetry has a large impact on hydrocarbon chain ordering, inducing disorder in the longer of the two hydrocarbons.

The coronavirus disease 2019 (COVID-19) pandemic is the defining global health and socioeconomic crisis of our time and represents the greatest challenge faced by the world since the end of the Second World War. The academic literature indicates that climatic features, specifically the temperature and absolute humidity, are very important factors affecting infectious pulmonary disease epidemics (e.g., SARS, MERS); however, the influence of climatic parameters on COVID-19 remains extremely controversial. The goal of this study is to quantify the existing relationship between several daily climate parameters (temperature, relative humidity, accumulated precipitation, solar radiation, wind direction and intensity, and evaporation), local morphological parameters, and new daily positive swabs for COVID-19, which represents the only parameter that can be statistically used to quantify the pandemic. The daily deaths parameter was not considered because it is not reliable due to frequent administrative errors. Daily data on meteorological conditions and new cases of COVID-19 were collected for the Lombardy area from March 1, 2020, to April 20, 2020. This region in Italy exhibited the largest number of official deaths in the world per million inhabitants, with a value of approximately 1700 per million on june 30, 2020. Moreover, the apparent lethality was approximately 17% in this area, mainly due to the considerable housing density and the extensive presence of industrial and craft areas. The Mann-Kendall test and multivariate statistical analysis showed that none of the considered climatic variables exhibited statistically significant relationships with the epidemiological evolution of COVID-19, at least in the spring months in temperate subcontinental climate areas, with the exception of solar radiation, which was directly related and showed an otherwise low explained variability of approximately 20%. Furthermore, the average temperatures of two highly representative meteorological stations of Molise and Lucania, the most weakly affected by the pandemic. The temperatures at these stations were approximately 1.5°C lower than that in the cities in Lombardy of Bergamo and Brescia, again confirming that a significant relationship between the increase in temperature and decrease in virology from COVID-19 was not evident, at least in the Italian peninsula.

The American leafhopper Erasmoneura vulnerata, detected in Europe in early 2000s, has recently become a pest in North-Italian vineyards. Issues were recorded in organic and conventional vine-yards despite the application of insecticides devoted to the control of other pests. Erasmoneura vulnerata completes three generations, and the second generation is frequently associated to large populations. The selection of appropriate active ingredients and the timing of their application is crucial for effective pest control. Field trials were carried out in North-eastern Italy, using a randomized design, to evaluate the impact of insecticides applied against other grapevine leafhoppers on E. vulnerata populations. The beginning of the second generation was selected as best timing for insecticide application. For a number of natural products, two applications were planned. Among the selected insecticides, the most effective were acetamiprid, flupyradifurone and lamb-da-cyhalothrin. Regarding natural products, the most effective was kaolin that could represent an alternative to pyrethrins in organic vineyards. The identification of pest threshold levels and the evaluation of side effects of the most effective insecticides on key natural enemies occurring in vineyards are required

Wireless power transfer promises to revolutionize the way we use and power mobile devices. However, low transfer efficiencies prevent this technology from seeing wide scale real-world adoption. The aim of this work is to use quasioptics to develop a system composed of a dielectric lens fed by a phased array to reduce spillover losses, increasing the beam efficiency, while working on the antenna system’s Fresnel zone. The DC-RF electronics, digital beamforming and beam-steering by an FPGA, and radiating 4x4 microstrip patch phased array have been developed and experimented upon, while the lens has been designed and simulated. This paper details these preliminary results, where the phased array radiation pattern was measured, showing that the beam is being generated and steered as expected, prompting the lens construction for the complete system experimentation.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

According to the International Agency for Research on Cancer (IARC) of the World Health Organization (data of year 2020), Breast Cancer (BC) is one of the most common cancer types worldwide, with large geographical variations occurring between countries and world regions and highest incidence rates in countries that have undergone economic transition. The risk factors for BC include women ageing, genetic mutations, reproductive history, dense breast tissues, personal history of BC or specific non-cancerous breast diseases, family history of breast or ovarian cancer, previous treatment using radiation therapy, and exposure to hormone-like drugs such as diethylstilbestrol (DES). Additional risk factors include being overweight or having obesity after menopause, and taking hormones. MicroRNAs (miRNAs or miRs) are small non-coding RNA molecules that have an essential role in gene expression and are significantly linked to the tumor development and angiogenesis process in different types of cancer, including BC. In the last years, the knowledge about miRNAs role in BC has significantly improved, and complex interactions among coding and non-coding RNA has been elucidated. In this context, an increasing number of papers had been published regarding the role of miR-125 in BC. In this review, we summarize the state-of-the-art about this research topic in addition to elaborating on the need to set novel ethical and legal standards for the governance of such innovations in healthcare.

Immunoglobulin G (IgG), a type of antibody, represents approximately 75% of serum antibodies in humans, and is the most common type of antibody found in blood circulation Consequently, the development of simple, fast and reliable systems for IgG detection are of considerable interest which can be achieved using electrochemical sandwich-type immunosensors. In this study we have developed an immunosensor sub-strate using an inexpensive and very simple fabrication method based on ZnO nanorods obtained through the electrodeposition of ZnO. The ZnO nanorods were treated by electrodepositing a layer of reduced gra-phene oxide to ensure an easy immobilization of the antibodies. On this substrate, the sandwich configura-tion of the immunosensor was built through different incubation steps, that were all optimized. The im-munosensor is electrochemically active thanks to the presence of gold nanoparticles tagging the secondary antibody, therefore it has been used to measure the current density of the hydrogen development reaction which is indirectly linked to the concentration of H-IgG antigens. In this way the calibration curve was constructed obtaining a linear range of 1-100 ng / ml with a detection limit of few ng / mL and good sensi-tivity.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

Soil texture is key information in agriculture for improving soil knowledge and crop performance, so the accurate mapping of this crucial feature is imperative for rationally planning cultivations and for targeting interventions. We studied the relationship between radioelements and soil texture in the Mezzano Lowland (Italy), a 189 km² agricultural plain investigated through a dedicated airborne gamma-ray spectroscopy survey. The K and Th abundances were used to retrieve the clay and sand content by means of a multi-approach method. Linear (simple and multiple) and non-linear (machine learning algorithms with deep neural networks) predictive models were trained and tested adopting a 1:50,000 scale soil texture map. The comparison of these approaches highlighted that the non-linear model introduces significant improvements in the prediction of soil texture fractions. The predicted maps of the clay and of the sand content were compared with the regional soil maps. Although the macro-structures were equally present, the airborne gamma-ray data permits us shedding light on finer features. Map areas with higher clay content were coincident with paleo-channels crossing the Mezzano Lowland in Etruscan and Roman periods, confirmed by the hydrographic setting of historical maps and by the geo-morphological features of the study area.