The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

Dirofilariosis is an infectious disease caused by species of the Dirofilaria genus. It is manifested by the appearance of a subcutaneous swelling, especially in the eye region. We present the case of a 29-year-old patient that accused facial asymmetry in the right genian region. Following clinical and paraclinical evaluations, the diagnosis of parasitic cyst was established in the context of dirofilariosis with Dirofilaria repens (D. repens). Treatment consisted of surgical excision of the formation associated with prophylactic antibiotic medication. Macroscopic analysis of the excision piece revealed a structure that contains a cystic cavity and a filamentous form with a length of approximately 10 mM and a diameter of 1 mM. This is the first case of dirofilariosis located in the genian region reported in Romania. The overview of this pathology is important to raise awareness among physicians about its presence and its clinical variations.

Diabetes mellitus is one of the most common endocrinopathies, estimated to affect about 5.4% of the world's population around 2025. It is thought that nearly a third of diabetic patients have some type of skin condition. Frequently, the cutaneous effects of this heterogeneous syndrome are ac-curately detected late in the progressive form of the disease. The main objective of the present study was to identify the main cellular characteristics of the cutaneous microenvironment in exper- imentally induced diabetes mellitus. Skin fragments were harvested from adult white Wistar rats of both sexes, with the weight of 200 g, 12 weeks after streptozotocin diabetes was induced. In parallel with histopathological diagnosis by using hematoxylin and eosine staining, samples were processed by transmission electron microscopy technique and examined with a Philips CM100 microscope. In the apparently macroscopically unchanged tegument, photon microscopy revealed both progres ive thinning of the epidermis in the early stages of diabetes and a significant process of fibrosis and collagen hyalinization in the dermis. In addition, in the early stages, the electron microscopic study provided ultrastructural details characteristic of a senescent phenotype with reduced cell proliferation. The morphological changes in the skin may be the first signs of disruption of carbohydrate metabolism and in the case of established diabetes may reflect its progression and the efficacy of therapy.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

Abstract: Congenital hyperinsulinism (CHI) is a rare disorder of glucose metabolism and is the most common cause of severe and persistent hypoglycemia (hyperinsulinemic hypoglycemia, HH) in the neonatal period and childhood. Most cases are caused by mutations in the ABCC8 and KCNJ11 genes that encode the ATP-sensitive potassium channel (KATP). We present the correlation between genetic heterogeneity and the variable phenotype in patients with early-onset hyperinsulinemic hypoglycemia caused by ABCC8 gene mutations. In the first patients, which presented persistent severe hypoglycemia since the first day of life, molecular genetic testing revealed the presence of a homozygous mutation in the ABCC8 gene [deletion in the ABCC8 gene c.(2390+1_2391-1)_(3329+1_3330- 1)del] correlated with a diffuse form of hyperinsulinism (the parents being healthy heterozygous carriers). In the second patient, the onset was on the third day of life with severe hypoglycemia, and genetic testing identified a heterozygous mutation in the ABCC8 gene c.1792C>T (p.Arg598*) inherited on the paternal line, which led to the diagnosis of focal form of hyperinsulinism. To locate the focal lesions, (18)F-DOPA (3,4-dihydroxy-6-[18F]fluoro-L-phenylalanine) PET/CT was recommended (an investigation that cannot be carried out in the country), but the parents refused to carry out the investigation abroad. In this case, early surgical treatment could have been curative. In addition, the second child also presented secondary adrenal insufficiency requiring replacement therapy. At the same time, she developed early recurrent seizures that required antiepileptic treatment. We emphasize the importance and of molecular genetic testing for diagnosis, management and genetic counseling in patients with HH.

Background: By 2025, road traffic injuries are projected to rank third in the global burden of disease, posing a significant challenge that affects health, social well-being, and economic aspects. According to data from the Romanian Police National Statistics Center, there has been an average of 342 traffic accidents per year involving pediatric patients over the past 10 years. Materials and Methods: A retrospective research study was conducted, encompassing 358 cases of road traffic accidents identified for the study. Data collection was conducted at "St. Mary’s" Emergency Hospital for Children in Iasi, Romania, from January 2015 to December 2022. To facilitate statistical analyses, participants were categorized into three specific age groups, correlating between the anatomical region affected and different types of accidents was examined, and the classification of injury types was determined based on the characteristics of the harm inflicted. Results: An oscillating trend is observed from 2015 to 2020, with its lowest value recorded in 2017 at around 6.8% and its peak in 2019 at 20.1%. Notably, post-pandemic (Covid-19), the cases underwent a substantial decline of approximately 50%. At least 78.7% of those who did not undergo orthopedic reduction required surgery, whereas among those who underwent orthopedic reduction, only 23.4% needed surgery. Regarding the frequency of complications 7,9% of the total cases experienced complications. Conclusion: The increased frequency of pediatric traffic accidents is attributed to the extensive services provided by "St. Mary’s" Emergency Hospital for Children, Iasi, to a significant number of patients from both rural and urban areas across the seven counties of the Moldova, Romania.

This study explores the complexities involved in the extraction and purification of catechins, prominent bioactive compounds found in plant extracts and tea. It addresses challenges arising from the intricate molecular structure of catechins and their inherent variability across botanical sources. Despite these obstacles, catechins present significant potential, particularly in healthcare. Their potent antioxidant properties have been extensively investigated and associated with numerous health benefits, positioning them as promising therapeutic agents for combating chronic diseases. Furthermore, catechins have diverse applications across various industries, including food and beverage, cosmetics, agriculture, and materials science. This abstract emphasizes the importance of continued research and innovation in catechin extraction and utilization, which hold promise for advancing human health and technological progress across multiple domains.

(1) Background: Thrombophilia is a tendency towards hypercoagulability, and it is increased by pregnancy, peaking around delivery. Research question: does thrombophilia stimulate the in-flammatory state of the patient, already suppressed by pregnancy? (2) Methods: Eighty thrombo-philia patients admitted for delivery between 1/10/2017 and 1/12/2021 were prospectively stud-ied, together with eighty age- and para-matched control patients. Patients were admitted for de-livery at term by means of cesarean section. The inflammation indexes from the complete blood count values analysis during both the 24 hours before and after labor—extracted from the hospi-tal’s medical records—were calculated and then correlated with uterine involution. (3) Results: Except for the PLR, most of the numerous inflammation indexes studied were not significantly different in treated thrombophilia patients, before and after delivery, compared to non-thrombophilia patients. Only when we split the patients, based on the uterine haematometra in the first 24-48 hours postpartum, we found out that the few treated thrombophilia patients with haematometra (14 with haematometra out of 79 with treated thrombophilia) had elevated SII and AISI antepartum. In pregnant patients treated for thrombophilia, MLR is higher in pa-tients without the Rh factor than in those with the Rh factor. In non-thrombophilia patients, MCVL and NLPR increased with age and before labor, while SII and AISI increased with age postpartum. (4) Conclusions: Thrombophilia did not stimulate the inflammatory state of the pa-tient, already suppressed by pregnancy.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

This research addresses a gap in the literature by conducting a comprehensive analysis of patients’ level of satisfaction with dental care. Methods: By combining quantitative and qualitative survey methods with the PSQ questionnaire this study aims to augment ongoing initiatives to enhance dental patients’ experiences by painting a more comprehensive depiction of patients' level of satisfaction; Results: When asked about their overall level of satisfaction 77,1% of the patients said they received excellent services from the office personnel and 72,2% said they trust their doctors; Conclusions: Assessing patient satisfaction in the realm of dental services quality is crucial for enhancing service quality and accuracy, benefiting both patients and dentists, and ultimately improving public health.

Landiolol is an ultra-short-acting, selective ß1- adrenergic receptor blocker that was originally approved by Japan for the treatment of intraoperative tachyarrhythmias. It has gained attention for its use in the management of tachyarrhythmias and perioperative tachycardia, especially atrial fibrillation for both cardiac and non-cardiac surgeries. It can be the ideal agent for heart rate control due to its high β1‐selectivity, the potent negative chronotropic effect, a limited negative inotropic potential, and an ultrashort elimination half‐life (around 4 min); moreover, it may have a potential therapeutic effect for sepsis and pediatric patients. Landiolol seems to be superior to other short‐acting and selective beta‐blockers such as esmolol. This review aims to provide a comprehensive overview of landiolol, a new ultra-short-acting ß1 selective antagonist, including its pharmacology, clinical applications, efficacy, safety profile, and future directions in research and clinical data.

(1) Background: The prediction of cervical lesions evolution is a challenge for clinicians. The prospective study aimed to determine and compare the predictive accuracy of cytology, HPV genotyping, and p16/Ki67 dual staining alone or in combination with personal risk factors for the prediction of progression, regression or persistence of cervical lesions in human papillomavirus (HPV)-infected patients; (2) Methods: This prospective study included HPV-positive patients with or without cervical lesions that underwent follow-up. Descriptive statistics and sensitivity analysis for individual or combined index tests were used for data analysis; (3) Results: The highest predictive performance for the progression of cervical lesions was achieved by a model that comprised a Pap smear suggestive of high-grade squamous intraepithelial lesion (HSIL), the presence of 16/18 HPV strains, a positive p16/Ki67 dual staining result along with the presence of at least 3 clinical risk factors, which had a sensitivity (Se) of 74.42%, a specificity of 97.92%, an area under the receiver operating curve (AUC) of 0.961, and an accuracy of 90.65%. The prediction of cervical lesions regression or persistence was modest; (4) Conclusions: Multiple testing or new biomarkers should be used to improve HPV-positive patient surveillance, especially for cervical lesion regression or persistence prediction.

Background: The purpuse was to investigate the influence induced by magnesium chloride (MgCl2) and zinc gluconate (ZnG) supplementation on liver and kidney injuries experimentally-induced with acetaminophen (AAPh) and potentiated by ciprofloxacin addition in rats. Material and methods: The experiment was performed on 5 animals groups: group 1 – control, treated for 6 weeks with normal saline, 1mL/kg; group 2 – AAPh, treated for 6 weeks with AAPh, 100 mg/ kg/day; group 3 – AAPh+C, treated AAPh 100 mg/kg/ day for 6 weeks and ciprofloxacin, 50mg /kg/day, only in the last 14 days of the experiment; group 4 – AAPh+C+Mg, with the same treatment as group 3, but, and in the last 14 days, MgCl2 10 mg/ kg/day was added; group 5 – AAPh+C+Zn, with the same treatment as group 3, but, and in the last 14 days, zinc gluconate (ZnG),10 mg/kg/day was added. All administrations were performed by oral gavage. At the end of the experiment, the animals were sacrificed and blood samples were collected for biochemistry examinations. Results: Treatment with AAPh for 6 weeks determined an alteration of the liver function (increases in alanine aminotransferase, aspartate aminotransferase, lactic dehydrogenase and, and gamma-glutamyl transferase) and of renal function (increases in serum urea and creatinine) (P < 0.001 group 2 vs. group 1 for all mentioned parameters). Also, the antioxidant defense capacity was impaired in group 2 vs. group 1 (superoxide dismutase and glutathione peroxidase activity decreased in group 2 vs. group 1, 0.001 < P < 0.01, respectively 0.01 < P < 0.05). The addition of ciprofloxacin, 50 mg/kg/day during the last 14 days resulted in further increases in alkaline phosphatase, alanine aminotransferase, aspartate aminotransferase, urea and creatinine (0.01 < P < 0.05, group 3 vs. group 2). MgCl2 provided a slight protection against liver enzymes increase and a more pronounced protection against the increase in serum urea and creatinine (0.001 < P < 0.01 group 4 vs. group 3). MgCl2 provided a slight protection against the decrease in superoxide dismutase (0.01 < P < 0.05 group 4 vs. group 3), but not against decrease of glutathione peroxidase. The improvement of mentioned parameters could also be seen in case of ZnG, to a higher extent especially in the case of alanine aminotransferase and lactic dehydrogenase (0.01 < P < 0.05 group 5 vs. group 4). Conclusions: This study represents a furthermore proof for beneficial effect of magnesium and zinc salts against toxicity induced by different agents, including antibacterials added to the analgesic and antipyretic acetaminophen; the protection is proven on the liver and kidney’s function; the antioxidant profile improvement has a key role, especially in case of zinc gluconate.

We consider a multitude of topics in mathematics where unification constructions play an important role: the Yang–Baxter equation and its modified version, Euler’s formula for dual numbers, means and their inequalities, topics in differential geometry, etc. It is interesting to observe that the idea of unification (unity and union) is also present in poetry. Moreover, Euler’s identity is a source of inspiration for the post-modern poets.

This paper is referred to a top frontline research in life science, showing that in spite of the large variation of the physiological architecture and behavioral forms of the living systems, the fundamental structure of their informational system is basically the same, allowing the body growth/development by micro to macro-structuration processes, maintaining the same informational configuration and functions like the basic unit of life – the eukaryotic cell. Starting and based on the determination of the special/specific info-operability in living structures and the role of information in structuration and their functionality, there are discussed the informational functions of the eukaryotic/prokaryotic cells, the simplest units of life and is elaborated and presented the Informational Model of the Living Structures, showing that these structures operate on the basis of two main informational systems: one of them defined as the Programmed Informational System, composed by three components, assuring respectively the info-generation, maintenance and the proliferation/reproduction, and another one defined as the Operative Informational System, necessary for the continuous communication with the environment for adaptation, consisting in four main components referred to memory, decision, sentience and info-connection/info-selection. The revealed properties are compared with the Informational System of the Human Body, as a prototype of a living system on the top of the evolutionary scale, showing/demonstrating the compatibility of structuration and functions on the entire scale, from prokaryotic/eukaryotic unit cells to multicellular organisms – plants, animals and human, by means of a continuous adaptation process, which always follows the same line of micro to macro-structuration process based on the same Info-organization and functionality. These models are new and revolutionary in the information and life sciences

This paper is based on a talk given at the 14-th International Workshop on Differential Geometry and Its Applications, hosted by the Petroleum Gas University from Ploiesti, between July 9-th and July 11-th, 2019. After presenting some historical facts, we will consider some geometry problems related to unification approaches. Jordan algebras and Lie algebras are the main non-associative structures. Attempts to unify non-associative algebras and associative algebras led to UJLA structures. Another algebraic structure which unifies non-associative algebras and associative algebras is the Yang-Baxter equation. We will review topics relared to the Yang-Baxter equation and Yang-Baxter systems, with the goal to unify constructions from Differential Geometry.

We consider several unification problems in mathematics. We refer to transcendental numbers. Also, we present some ways to unify the main non-associative algebras (Lie algebras and Jordan algebras) and associative algebras.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

Bringing toghether mathematical and philosophical ideas related to transcendental numbers, this paper begins with a survey on transcendence and transcendental numbers, it then presents several properties of the transcendental numbers e and π, and then it gives the proof of a new inequality for transcendental numbers. Also, in relationship with these topics, we study solutions to the Yang-Baxter equation from hyperbolic functions and from logical implication.

The present article seeks to analyse the period 1938-1940, when the Romanian interwar democracy was suspended through the promulgation of the anti-liberal Constitution of 27 February 1938. The Constitution abolished the political parties and trade unions, replacing them with new institutions established according to royal decrees: the royal single party, known as the National Renaissance Front (Frontul Renaşterii Naţionale, FRN) and corporations of workers and employers, respectively. Starting from that moment, the regime, through its representatives, made recourse to a nationalist rhetoric directed against the democratic parliamentary system. Moreover, a cult of personality of the monarch can be identified in the speeches of the royal corporatist ‘parliament’, as well as in the doctrine of FRN and the Nation’s Party (its successor), but also in the regime’s youth organisation, ‘The Country’s Sentinel’ (Straja Ţării), whose First Sentinel was the authoritarian monarch himself. Thus, the cult of personality of Carol II represented one of the sources of inspiration for the dictator Nicolae Ceauşescu and for the leaders of this totalitarian regime.

The purpose of the research was to obtain information about the necessity and efficiency of the application of localized irrigation to some qualitative indices of plum trees in the nursery, against the background of different fertilization treatments. The expected results to be obtained by applying differentiated rules of irrigation and fertilization will consist in obtaining a healthy, vigorous fruit tree planting material, increasing production in the nursery. With fruit trees in the nursery, as with all cultivated plants, the growth process depends to the greatest extent on the climate and soil conditions available to them. The use of fertilizers in tree culture becomes necessary to renew the reserve of nutrients consumed by plants or leached in depth, then to improve the physical condition, the chemical composition, and the overall state of fertilization of the soil. It is necessary to intervene every year, in several rounds, with fertilizations that ensure, on the one hand, the achievement of a certain level of production, and on the other hand, a certain level and ratio of nutritional elements by returning the amounts of elements easily accessible nutrients extracted with the harvest to be able to maintain, in this way, the fertility of the soil in accordance with the age of the plantation and the level of production. The two varieties of plum studied were Stanley and Cacanska Lepotica, two valuable varieties for the quality of the fruit. During the research, the fertilization treatments had the highest contribution (34.50 %) on the stem diameter, compared to irrigation (20.67 %) and respectively the variety (5.63 %), considering that the variety did not significantly influence the increase in diameter of the grafted trees.

The subject of this paper is to analyse the Math Principia of Economic 3D Black Holes in Roegenian economics. This idea is totally new in the related literature, excepting our papers. In details, we study two special problems: (i) math origin of economic 3D black holes, (ii) entropy and internal political stability depending on national income and the total investment, for economic RN 3D black hole. To solve these problems, it was necessary to jump from macroeconomic side to microeconomic side (a substantial approach so different), to complete the thermodynamics-economics dictionary with new entities, to introduce the flow between two macroeconomic systems, to study the Schwarzschild type metric properties on an economic 4D system, together with Rindler coordinates, Einstein 4D PDEs, and economic RN 3D black hole. In addition, we introduce some economic Ricci type flows or waves, for further research.

The role of the databases is to allow persisting data, no matter if they are of the SQL or NoSQL type. In SQL databases, data is structured in a set of tables in the relational database model, grouped in rows and columns. The CRUD operations (create, read, update, and delete) are used to manage the information contained in the relational databases. Several dialects of the SQL language exist, as well as frameworks for mapping Java classes (models) to a relational database. The question is what we should choose for our Java application and why. A comparison between the most used relational database management systems, mixed with the most used frameworks should give us some guidance about when to use what. The evaluation is done on timing for each CRUD operation, from thousands to millions of entries, using the possible combinations between the relational database system and the framework. The experiments included the possibilities to warm up the Java Virtual Machine before the execution of the queries. Also, the research investigated the time spent inside different methods of the code, to determine the critical regions. Thus, the conclusions provide a comprehensive overview of the performances of Java applications accessing databases depending on the suite of decisions considering the database type, the framework in use, the type of operation, and supporting architects and developers for their technological decisions and for improving the speed of their programs.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

Antimicrobial resistance (AMR) is a worldwide healthcare problem. Multidrug resistant organisms (MDRO) have the ability to spread quickly owing to their resistance mechanisms. Although colonized individuals are crucial MDRO dispensers, colonizing microbes have the potential to turn pathogenic under certain conditions, leading to symptomatic infections in carriers. Carbapenemase producing Enterobacterales (CPE) are among the most important MDRO involved in infections and colonizations, associating with multiple resistance mechanisms and virulence factors, causing infections with severe outcomes. All research papers identified in the most comprehensive online databases which contained information related to the topic of this article were analyzed, and relevant data was extracted and included. The first information on CPE could be traced back to the mid-2000s, but pertinent data for many African countries was established in the past 5-8 years. Information is presented chronologically for each country. Although no clear conclusions could be drawn for some countries, it was observed that CPE colonizations are present in most African countries and carbapenem-resistance levels are rising. The most common CPE involved are Klebsiella pneumoniae and Escherichia coli, and the most prevalent carbapenemases are NDM-type and OXA-48-type enzymes. Prophylactic measures, such as screening, are required to combat this phenomenon.

The aim of this paper is to determine a suitable definition for the concept of fuzzy Hilbert space. In order to achieve this, we firstly focused on various approaches from the already-existent literature. Then we considered another approach to the notion of fuzzy inner product and analysed its properties.

Abstract: This work is presenting a water level control and monitoring system in a tank, by using the development boards Arduino Uno, NodeMCU ESP8266 and the ultrasonic sensor HC-SR04. The water tank is supplied through a pump controlled by the development board Arduino Uno by means of a relay. The author has issued a control algorithm for controlling the water level and a program in the development environment Arduino IDE that has been implemented and validated on the experimental stand. For monitoring the development board NodeMCU ESP8266 has been used that takes the information from the ultrasonic sensor HC-SR04 and sends it through Wi-Fi to the platform ThingSpeak. Based on the experimental results it has been found out that the water level control system in the tank provides the performances imposed through the designing stage, and the pump running has been automatically stopped when the limit, settled through the program for the water maximum level in the tank, has been reached. The measured value of the water level is shown on the LCD 1602 display. In the water circuit of the home consumers or irrigation systems supplied from the tank a pump controlled by means of a mobile phone has been installed. In order to implement this control system, the author has issued a program for another development board Arduino Uno, whilst for the mobile phone he used the application Arduino Bluetooth Control. The advantage of this water level control and monitoring system in the tank is given by the very low costs in comparison to the cost of an industrial type control system.

The aim of this study was characterization of some dairy drinks based on Milk Serum regarding major whey proteins (WP) and free amino acids (FAAs) using reversed phase high performance liquid chromatographic (RP-HPLC) methods. The studied WP, -lactalbumin (-La), bovine serum albumin (BSA), -lactoglobulin A (-Lg A) and -lactoglobulin B (-Lg B) were separated on Aeris XB-C18 column at 214 nm detection. The RP-HPLC method was validated by selectivity, linearity (R2 ≥0.99), sensitivity (LOQ, 1.35–10.08 µg mL−1), accuracy (recovery 96.79-103.07%) and precision (% RSD ≤ 4.13%). The total studied WP in studied dairy drinks varied between 1.42 and 3.047 g·L-1. The chromatographic profile of FAAs (aspartic acid, glutamic acid, serine, histidine, arginine, glycine, threonine, alanine, tyrosine, cysteine, tryptophan, methionine, valine, phenylalanine, isoleucine, leucine and lysine) was determined in lyophilized concentrate of Milk Serum by RP-HPLC using pre-column derivatization reaction with orthophthalaldehyde (OPA). The total studied FAAs in studied samples varied between 1.103 and 1.119 mg·g-1. Moreover, the Milk Serum showed bacteriostatic activity against two bacterial strains Escherichia coli and Staphylococcus aureus. The obtained results confirm that dairy drinks based on the Milk Serum constitutes a valuable sources of bioactive components with benefits for human healthy nutrition.

Aspartame is the methyl-ester of the aspartate-phenylalanine dipeptide. Over time it became a very popular artificial sweetener. However, since its approval by the main food safety agencies, several concerns have been raised related to neuropsychiatric effects and neurotoxicity, due to its ability to activate glutamate receptors, as well as carcinogenic risks by increased production of reactive oxygen species. Within this review we critically evaluated reports concerning the safety of aspartame. Some studies evidenced subtle mood and behavioral changes upon daily high-dose intake below the admitted limit. Epidemiology studies also evidenced associations between daily aspartame intake and higher predisposition for malignant diseases like non-Hodgkin lymphomas and multiple myelomas, particularly in males, but association by chance still could not be excluded. While the debate over the carcinogenic risk of aspartame is ongoing, it is clear that its use may pose some dangers in peculiar cases, such as patients with seizures or other neurological diseases; it should be totally forbidden for patients with phenylketonuria, and reduced doses or complete avoidance are advisable during pregnancy. It would be also highly desirable for every product containing aspartame to clearly indicate on the label the exact amount of the substance and some risk warnings.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

This work promotes new methods in Mathematical Modeling, consisting in the use of the methods of Non-standard Analysis in Topoi, having as its main purpose, the mathematical definitions of the pseudoparticles from the title, with arguments from Biology/Physiology (Mathematical Neuroscience), Physics (String Theory and Emergent Quantum Mechanics), and Cybernetics (Global Brain, including Natural and Artificial Intelligence). The connections between brain and mind will be scketched via the genetic/epigenetic interplay. The topoi model the intuitionistic logic (multi-valued) and have been used in Quantum Physics while Non-Standard Analysis in SET (= the Category of sets) has been applied in Mathematical Economics; topics from Theory of Categories were also used in the study of Consciousness; however, the combination topoi - non-standard analysis was never used until now in Applied Mathematics. Another important objective is to produce progress in this aria of Pure Mathematics also - the build of non-standard analysis in classes of topoi, already used in Physics. We propose the logic of non-standard extensions in topoi as a model of the human thinking (based on infons/receptons), these theories representing new top and very difficult results in Abstract Mathematics either.

Background and Objectives: High job strain is worsening the outcome in coronary artery disease, CAD. Severe dissatisfaction on workplace, imbalance between high demands , and low rewards, are affecting the quality of life, and diminishing the duration of life, especially in CAD patients. Our study included two samples : CAD patients (experimental group), and without CAD patients, but with traditional risk factors (control group). The main objective of the study was the role played by high sensitivity C reactive protein, hs CRP, and microalbuminuria, as mediators of job strain and CAD relationship. Secondary objectives were the following: identification of the most vulnerable patients( with significant job strain) and intervention towards this category, for cardiovascular events prevention (primary or secondary). Materials and Methods: The utilized methods were the following : clinical exam; electrocardiogram; echocardiogram; non contrast enhanced computed chest tomography; laboratory findings ( lipid profile, glycemia, hs CRP, microalbuminuria); type D scale, DS 14; depression questionnaire, PHQ-9; and satisfaction with work scale, SWWS. Results: The highest values for hs CRP and microalbuminuria were noticed in patients with the lowest Likert score, for both samples CAD, and without CAD patients. The highest job strain was noticed in females. More than half of CAD patients ,with low Likert scores, revealed myocardial infarction. Conclusions: Microalbuminuria and hs CRP were statistical significant in the study as intercessors, in job strain and CAD relationship. The most vulnerable patients for vascular events were females, in both groups : CAD and “CAD waiting desk”. In CAD sample, the vascular vulnerability was also increased by high job strain.

Today massive amounts of sequenced metagenomic and -transcriptomic data from different ecological niches and environmental locations are available. Scientific progress depends critically on methods that allow extracting useful information from the various types of sequence data. Here, we will first discuss types of information contained in the various flavours of biological sequence data, and how this information can be interpreted to increase our scientific knowledge and understanding. We argue that a mechanistic understanding is required to consistently interpret experimental observations, and that this understanding is greatly facilitated by the generation and analysis of dynamic mathematical models. We conclude that, in order to construct mathematical models and to test mechanistic hypotheses, time-series data is of critical importance. We review diverse techniques to analyse time-series data and discuss various approaches by which time-series of biological sequence data was successfully used to derive and test mechanistic hypotheses. Analysing the bottlenecks of current strategies in the extraction of knowledge and understanding from data, we conclude that combined experimental and theoretical efforts should be implemented as early as possible during the planning phase of individual experiments and scientific research projects.

The medical sector is of the utmost importance in every country for well-known reasons such as their economic development, national security, quality of life, and so on. Many researchers were dedicated to this topic, however, in Romania there are limited studies on this subject. One reason is that most of the businesses in this sector are individual enterprises or small family businesses. In our research paper we deploy several analysis methods to see the financial sustainability of companies operating in the medical industry. By analyzing a sample of 23931 companies and we have concluded that their performance has increase in the peak of the pandemic and that the financial stability is high. Our results are in line with other similar studies that were conducted in other regions.

This paper is a continuation of previous papers on unification theories publishes in AXIOMS. We present results about the (modified) Yang-Baxter equation, Euler’s formula, dual numbers, coalgebra structures, non-associative structures, differential geometry, and (mean) inequalities. We will also attempt to relate our discussion to some Brain Studies and Machine Learnig.

Distribution systems can form islands when faults occur. Each island represents a subsection with variable boundaries subject to the location of a fault(s) in the system. A subsection with variable boundaries is referred to as island in this paper. For operation in autonomous mode, it is imperative to detect the island configurations and stabilize these subsections. This paper presents a novel scheme for the detection of islanding boundaries and stabilizing the system during autonomous operation. In the first stage, a boundary detection method is proposed to detect the configuration of the island. In the second stage a dynamic voltage sensitivity factor (DVSF) is proposed to assess the dynamic performance of the system. In the third stage, a wide area load shedding program is adopted based on DVSF to shed the load in weak busbars and stabilize the system. The proposed scheme is validated and tested on a generic 18-bus system using a combination of EMTDC/PSCAD and MATLAB softwares.

The climate crisis necessitates a global shift to achieve a secure, sustainable, and affordable energy system toward a green energy transition reaching climate neutrality by 2050. Because of this, renewable energy sources have come to the forefront and the research interest in microgrids which rely on distributed generation and storage systems has exploded. Furthermore, many new markets for energy trading, ancillary services, and frequency reserve markets have provided attractive investment opportunities in exchange for balancing the supply and demand of electricity. Artificial intelligence can be utilized to locally optimize energy consumption, trade energy with the main grid, and participate in these markets. Reinforcement learning (RL) is one of the most promising approaches to achieve this goal because it enables an agent to learn optimal behavior in a microgrid by executing specific actions that maximize the long-term reward signal/function. The study focuses on testing two optimization algorithms: logic-based optimization and reinforcement learning. This paper proposes an optimization algorithm based on reinforcement learning in an industrial microgrid that is capable of trading energy with the main grid, providing significant cost savings. The RL-based approach is implemented in Python based on real data from the site and in combination with MATLAB-Simulink to validate its results. The application of the RL algorithm achieved an average monthly cost saving of 20% compared to logic-based optimization and 86% savings compared to not using any optimization. These findings contribute to digitalization and decarbonization of energy technology and support fundamental goals and policies of the European Green Deal.

The splitting method developed in a previous study for linear, multi – component, convection-diffusion mass transfer equations is extended to non-linear, multi-component, convection-diffusion mass transfer equations. The diffusion term is non-linear (the diffusion coefficients depend on chemical species concentrations). Theoretical results about the splitting error are presented, as well as numerical simulations for mixtures with n ≤ 5. The numerical experiments show second-order accuracy and stability for the present splitting algorithm.

Incisional hernias have a particular dynamic related both to the repair method and to the absence or presence of a prosthetic material. The incidence of incisional hernias is estimated at 9.8% after 21 months and increases to 18.7% after ten years. This study presents a surgical method for the repair of recurrent incisional hernias, through open surgery and the use of existing mesh. The selection criteria regarding the use of this method are: the prosthesis is well integrated, without granulomas, suppurations, defect appearing on the same prosthetic abdominal area. The analyzed factors were the location of the incisional hernias, the duration of the operation, the duration of hospitalization, identified complications, the size of the parietal defect. The retrospective study carried out focused on recurrences of incisional hernias from a group of 631 patients operated on for incisional hernias in a general surgery department of Dr. Constantin Andreoiu County Emergency Hospital, Ploiești, Romania, during January 2018 - December 2022. Of the total of 18.22% relapses, 13.6% were relapsed eventrations after prosthetic procedures. Following the application of the selection criteria, several 8 patients with recurrent eventrations were operated by the open method using the existing mesh. In the case of recurrences after prosthetic procedures of incisional hernias, the recurrence can be solved by open surgery using the existing well-integrated prosthesis, without tension, absence of suppuration in the wound, and the peritoneal cavity. For the presented case, the return to daily activities occurred after 22 hours of hospitalization.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

The emergence of M. tuberculosis strains resistant to Isoniazid (INH) and Rifampicin (RIF), the two most potent drugs of first-line anti-TB therapy is termed multidrug drug-resistant TB (MDR-TB). Multidrug-resistant tuberculosis has been a serious medical and epidemic problem all over the world. We present here a series of clinical cases consist of two patients diagnosed with isoniazid resistant tuberculosis. Histopathological examination supports the diagnosis of tuberculous granulomas. And the pathology molecular examination revealed the presence of Isoniazid-resistant Mycobacterium tuberculosis1,2 via the following mutation c.947G&gt;A; p.Gly316Asp. Isoniazid-resistance is associated with mutations in the furA-katG and fabG1-inhA operons, as well as mutations in the ahpC gene. 64% of the isoniazid-resistance phenotypes were associated with the katG315 mutation worldwide. The second most common mutation is inhA-15, and it has been reported in 19% of the Isoniazid-resistant isolates. The significant association between the two mutations, inhA c-15 and katG 315 respectively, and the high-level resistance is of interest in the interpretation of current and future molecular diagnostic testing, as an early prediction of the level of Isoniazid-resistance is essential to decide the benefit of high-dose Isoniazid use.

This paper presents a study of the 2D roughness profiles on a flat surface generated on a steel work piece, by ball nose end milling, with linear equidistant tool paths (pick-intervals). The milled surface exploration with a surface roughness tester (on pick and feed directions) produces usually 2D roughness profiles having periodical evolutions. These evolutions can be seen as time-dependent signals, describable as a sum of sinusoidal components (the wavelength of each component being regarded as a period). In order to detect a well approximated description of these components, two appropriate signal processing techniques are used in this work: first technique provides a direct mathematical (analytical) description and is based on computer aided curve (signal) fitting (more accurate), the second technique (providing an indirect and incomplete description) is based on the spectrum generated by fast Fourier transform (less accurate). This study can be seen as a way for a better understanding the interaction between the tool and the work piece or to achieve a mathematical description of the machined surface microgeometry in terms of roughness (e. g. its description being a collection of closely spaced 2D roughness profiles).

This paper proposes the recycling of plates from spent car batteries by the melt quenching method and the incorporation of NiO or Co3O4 contents in order to improve the electrochemical performance of new materials for applications as electrodes on batteries. The analysis of X - ray diffractograms indicates the gradual decrease of the sulfated crystalline phases, respectively 4PbO•PbSO4 and PbO•PbSO4 phases until their disappearance for higher dopant concentrations. IR data show a decreasing trend in the intensity of the bands assigned to sulfate ions and a conversion of [PbO3] pyramidal units into [PbO4] tetrahedral units by doping with high dopant levels yielding to the formation of the PbO2 crystalline phase. The EPR data indicate three resonance lines centered on the gyromagnetic factor, g ~ 2, 2.2 and 8, which are dependent on the NiO level. The first two resonance lines are assigned to nickel ions in higher oxidation states and the last signal centered at g ~ 8 corresponds to nickel metal nanoparticles. This compositional evolution can be explained by considering a process of drastic reduction of nickel ions in oxidation states superior to metallic nickel. The linewidth and the intensity of resonance lines situated at about g ~ 2, 2.17, 4.22 and 7.8 corresponding to the Co+2 ions from EPR spectra depend very strongly on the Co3O4 concentration. The best reversibility of the cyclic voltammograms was highlighted for the samples with x = 8 mol% NiO and 10 mol% Co3O4, which are recommended as suitable in applications as electrode for renewable batteries.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

In the current socio-economic context, pension systems have become a crucial topic in the agenda of governments and international bodies. In this paper, an empirical study regarding the economic and social sustainability of pension systems in Central and Eastern European Countries was performed. The goal of the research is to establish the sustainability of pension systems with econometric modeling techniques on three dimensions as the research hypotheses are revealed: first, by strengthening the financial soundness of pension systems; second, consolidating the economic environment of pension systems; third, increasing the degree of social security systems with a direct effect of reducing poverty. The results led to relevant insights emphasizing the need for more inclusive economic, financial, and social reforms. From a policy perspective, these findings could be a starting point for the enhancement of the financial adequacy and economic and social sustainability of pension systems in Central and Eastern European Countries. The econometric techniques in this study highlight those modern pensions systems that need to be addressed in a more complex and empirical context that must encompass the main technical aspects. The conclusions suggest that in the future it needs judicial, economic, and social adjustments for the enhancement of the financial soundness of the pension systems.

The increase in the emission of greenhouse gases (GHG) is one of the most important world problems. Decreasing of GHG emission is a big challenge in the future. Transportation sector uses a significant part of petroleum production in the world and it leads to an increase in the emission of GHG. The result of this issue is that population of the world befoul environment of transportation system automatically. Electric Vehicles (EV) have a potentiality to solve a big part of the GHG emission and energy efficiency issues such as stability and reality of energy. The energy actors and their research team determine some targets for 2050; hence, they hope to decrease the world temperature to 6 °C in the best and 2 °C in the normal condition. Fulfillment of these scenarios needs suitable grid infrastructure but in most of the countries, the grid does not have a suitable background to apply those scenarios. In this paper, some problems about energy scenarios, energy storage systems, grid infrastructure and communication systems in supply and demand side of the grid and its solutions have been investigated.

The purpose of the study is to show the effect of the intake of vitamin C obtained from a diet rich in fruit and vegetables or vitamin C supplements on the level of vitamin C in the plasma. The level of vitamin C in plasma were determined before the study (T1), and after five months (T2). Moreover, a medical record was carried out and a questionnaire on the habits such as general eating and specific consumption of food rich in vitamin C. Both of them were completed before and after five months. In addition, related anthropometric analyses were carried out. The results of the first determination of vitamin C level in plasma were between 1.0 and 16.0 mg/L and the results of the second determination of vitamin C in plasma were between 4.9 and 14.1 mg/L. Furthermore, it was identified that 50% of the questioned people had a low fruit intake. Raw vegetables were consumed by fewer people, the intake being higher during the main meals. The correlation of plasma vitamin C with the eating habits of the subjects to the study points out an interdependence between the consumption of fruit and vegetables and the level of vitamin C in the plasma.

The paper focuses of the interaction between tungsten (W) wire and microwave field in carbon dioxide (CO2) atmosphere. Our experimental set-up uses a microwave plasma generator in order to generate the plasma from the metallic wires. The microwave plasma generator contain a cylindrical cavity - TM_011 propagation modes, commercial source (magnetron) having the 2.45 GHz frequency at 800 W microwave and power supply. In the focal point of the cylindrical cavity we have a high energy of the electromagnetic radiation. The metallic wires from this area will be vaporized and ionized having as effect CO2 dissociation. The electron temperature regarding metallic plasma produced was estimated using the ratio of atomic emission lines acquired by a high definition of the optical multichannel spectrometer. Determination of the CO2 dissociation quantity was estimated measuring of the carbon monoxide (CO) resulting of the CO2 dissociation process. We obtained a high electron temperature of the plasma and a strong dissociation of the CO2.

Considering the worldwide impact of heart failure, it is crucial to develop approaches that can help us comprehend its root cause and make accurate predictions about its outcome. This is essential for lowering the suffering and death rates connected with this widespread illness. Cardiomyopathies frequently result from genetic factors, and the study of heart failure genetics is advancing quickly. Dilated cardiomyopathy (DCM) is the most prevalent kind of cardiomyopathy, encompassing both hereditary and nongenetic abnormalities. It is distinguished by the enlargement of the left ventricle or both ventricles, accompanied by reduced contractility. The discovery of the molecular origins and subsequent awareness of the molecular mechanism is broadening our knowledge of DCM development. Additionally, it emphasizes the complicated nature of DCM and the necessity to formulate several different strategies to address the diverse underlying factors contributing to this disease. Genetic variations that can be transmitted from one generation to another can be a significant contributor to causing family or isolated DCM. Genetic variation also plays a significant role in determining susceptibility for acquired triggers for DCM. The genetic causes of DCM can have a diverse range of phenotypic expressions. It is crucial to select the most probable patients to have advantages from genetic testing. The purpose of this research is to emphasize the significance of identifying genetic DCM, the crucial relationships between genotype and phenotype, and the usefulness of genetic testing in the therapeutic care of both those affected and their relatives. This approach is expected to gain importance once treatment is guided by genotype-specific advice and disease-modifying medications.

Introduction. Intra-abdominal cystic formations represent heterogeneous pathologies with varied localization and clinical manifestation. The first challenge of a giant intra-abdominal cystic lesion is identifying the organ of origin. The clinical presentation of intra-abdominal cystic lesions varies from acute manifestations to non-specific symptoms or accidental discovery. Case presentation: A 2-year-old girl presents to the emergency unit with a fever of 38.5 Celsius, loss of appetite, and apathy. The investigations showed a gigantic intra-abdominal mass whose organ belonging could not be specified. Postoperatively, a giant mesenteric lymphangioma was evident, which was completely excised. Discussions Giant cystic formations modify the anatomical reports and become space-replacing formations, and the starting point is even more challenging to assess preoperatively. Nevertheless, the careful evaluation of the characteristics of the formation, the effect on the adjacent organs, the age of the patient, and the clinical picture can provide elements of differential diagnosis.

Groove pancreatitis represents a chronic focal form of pancreatitis affecting the zone between the pancreatic head and the duodenal „C” loop, known as the groove area. This is a rare condition that affects the pancreatic periampullary part, including the duodenum and the common bile duct, associated usually with long-term alcohol and tobacco misuse and being more frequent in men than in women. The most common clinical symptoms of groove pancreatitis include weight loss, acute abdominal pain, nausea, and jaundice. This report is about a 66 year old woman with a history of heavy smoking, presenting with weight loss, nausea, and upper abdominal pain. Contrast enhanced computed tomography revealed the existence of a chronic pancreatitis as well as the dilatation of the main pancreatic duct, a cyst of the pancreatic head and enlargement of the biliary tract. Conservatory treatment was initiated but with no improvement of symptoms. Since there was no indication for endoscopic retrograde cholangiopancreatography, we decided to perform a pancreatoduodenectomy, as surgery appears to be the single effective treatment.

The paper highlights the performance of the seismic isolation devices, installed on retrofitted buildings in reducing the seismic response when subjected to earthquakes. Two buildings from the beginning of the XX-th century in Bucharest are chosen from many more, monitored over the city area. We discuss the response of these base-seismic isolated structures, relying on good quality data acquired from the recent strong earthquake (03.11.2022, MW = 5.0). Elastic response spectra computed from recordings at two levels of each structure are used, placed under and right above the isolating layer. At one building the existence of previous recordings and the particularity of the sensors allow a comparison with other two relatively recent medium intensity earthquakes. The assessment is carried out in terms of maximum acceleration amax, measured at certain levels in each structure, spectral acceleration amplitude SAmax and spectral-peak corresponding period. We find that the base-isolation methodology is effective in reducing the response of the building right above the isolating layer, an observation valid for both structures, all components of the recordings, and spectral acceleration values. Moreover, the outcomes from the modal evaluation performed prior to rehabilitation and seismic isolation process are presented, by pointing out a higher newly acquired fundamental period of the isolated structures.

The processing of cloud free geo-referenced imagery is one of the preliminary processing step of any land application. This letter describe the methodology developed to obtain a seamless cloud free composite of Africa for 2016 using Sentinel-2A data at 10 meters resolution freely available from the European Space Agency. The method is based on an hybrid method resulting from the merging of the two most robust time series methods namely the "darkest pixel" and the "maximum NDVI" previously developed with AVHRR time series.

This research work deals with the modeling and control of hybrid photovoltaic (PV) - Wind micro-grid using Quasi Z-Source inverter. This inverter provides better buck/boost characteristics, able to regulate the phase angle output, less harmonic content, no requirement of the filter and has high power performance characteristics over conventional inverter as major benefits. A SEPIC converter as dc-dc switched power apparatus is employed for maximum power point tracking (MPPT) functions which provides high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) method has been proposed in the PV MPPT action which forces the operating point close to maximum power point (MPP). Practical responses justify the performance of hybrid PV-Wind micro-grid with Quasi Z-Source inverter structure.

In the context of globalization One Health enables and concurs to the achievement of Global Health. One Health approach involves wide knowledge and understanding of its critical factors, next to an adequate implementation, also in farm animal sector. Moreover, animal farming and breeding shows particularities depending on country. Therefore, well-defined and specific strategies are still needed to be developed and adapted to the current conditions found in various countries for ensuring a well implementation, thus driving to better and healthier global outcomes and security. This paper will explore the One Health status in Romania, highlighting the current progress registered until now and the future perspectives based on its potential, in the context of the livestock farming framework and challenges. Our findings may help to disclose the challenges of putting in practice One Health in Romania, alongside to the pathways showing potential to enhance sustainability in livestock farming.

In this study, the effect of ZnO nanoparticles (Zn NPs) on the performance of epoxy resin composites was investigated. The new ZnO/epoxy resin composites were synthesized using halloysite nanotubes (HNT) and different types of ZnO nanoparticles (commercial ZnO and ZnO-ODTES). These ZnO nanoparticles were utilized for intending to enhance the interfacial bonding between the epoxy resin and the reinforcement. Various methods such as FTIR, TGA, DSC, TEM-EDX, and Nanoindentation analyses were used to prove that the ZnO nanoparticles can improve the properties of epoxy resin composites. The thermal properties of the epoxy resin composites were enhanced to a greater extent by the addition of ZnO NPS. DSC testing proved that the epoxy resin composites modified with ZnO NPS are more flexible and elastic than unmodified epoxy resin. It was seen that the epoxy resin modified with ZnO-ODTES shows a much improved hardness and penetration depth compared to the other samples. These findings can pave the way for the developing of ZnO-based marine coatings with improved properties.

Grid energy storage system for PV Applications is connected with three different power sources i.e. PV Array, Battery and the Grid. It is advisable to have Isolation between these three different sources to provide safety for the equipment. The configuration proposed in this paper provides the complete isolation between the three sources. A Power Balancing Control (PBC) for this configuration is proposed to operate the system in three different modes of operation. Control of a dual active bridge (DAB) based battery charger which provides a galvanic isolation between batteries and other sources is explained briefly. Various modes of operation of a Grid energy storage system are also presented in this paper. Hardware-In-Loop (HIL) Simulation is carried out to check the performance of the system and the PBC algorithm. Power circuit (comprises of inverter, dual active bridge based battery charger, grid, PV cell, batteries, contactors and switches) is simulated and the controller hardware and user interface panel are connected as HIL with the simulated power circuit through Real Time Digital Simulator (RTDS). HIL simulation results are presented to explain the control operation, steady state performance in different modes of operation and the dynamic response of the system.

Any malocclusion can be associated with various face development patterns, including hyper, neutral and hypodivergent growth patterns. We measured face height ratios, angle formed by Y axis to SN and growth patterns in various malocclusions in a group of patients from Timis county. The pretreatment digital cephalograms of 350 participants were split into three groups based on Angle's classification of dentoalveolar malocclusion. Every cephalogram was digitally traced and analyzed using a composite cephalometric method analysis utilizing the WebCeph imaging cephalometric program, which included two linear and one angular. In general, patients from Timis county have a hypodivergent development pattern. Hypodivergent development pattern predominated in group I, II, and III. Group I hyperdivergent 5.14%, normodivergent 16.01%, hypodivergent 78.85%. Group II hyperdivergent 2.78%, normodivergent 14.44%, hypodivergent 82.78%. Group III hyperdivergent 10.53%, normodivergent 10.53%, hypodivergent 78.94%. In all three groups, the value of the angle formed by Y axis to SN is within normal limits group I 65.4 ±4.34°, group II 63.87± 3.86° and group III 64.66 ±5.28°. A strong negative correlation was found between angle: Y axis to SN and facial height ratio (r= -0,766; p &lt;0.001). In all kinds of malocclusion, patients from Timis county show primarily a hypodivergent development pattern.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

The drug delivery systems receive more and more attention for the control and treatment of many diseases due to their increased number in recent years. The main aims of this study were to develop and to characterize a polyurethane drug delivery system that it is intended to be used for the transmembrane transport of nucleosides. Three different samples have been synthesized based on aliphatic diisocyanates (hexamethylene diisocyanate, isophorone diisocyanate and lysine diisocyanate) as organic phase, respectively a mixture of polyethylene glycol, polycaprolactone diol and low molecular weight diols as aqueous phase. The samples were characterized by pH, refractivity index and solubility measurements, drug loading efficacy and release investigations, thermal behavior, Zetasizer, cells viability and irritation tests on mice skin. The results indicate the obtaining of different populations of neutral acido-basic particles with size between 132 and 190 nm; the Zeta potential values and SEM images show a medium tendency to form clusters, while UV-Vis evaluations indicate an almost 70% encapsulation efficacy, a prolonged release (45% of encapsulated substance is released in the first 5 days) and around 70% of particles have penetrated an artificial membrane in the first 24h. The synthesized products can be tested in further clinical trials, the currently tests on cells culture and mice skin revealing no side effects.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

The objective of this research is to analyze metal elements like Na (sodium), Mg (magnesium), Al (aluminum), Si (silicon), Pb (lead), K (potassium), Ca (calcium), and Fe (iron) found in dust particles within two distinct areas from which the sampling has been done. First sampling was taken from the road verge of a highly trafficked road section, while the second sampling was done in a residential garden area 90 m away from the road. Several metal elements have been detected, with a high difference for Silicon Si, which present higher concentrations in the dust sampled from the road verge area. Pb has only been detected in the samples taken from the road verge, which could be explained by residual remnants from old lead gasoline, and wheel weights. Additionally, airborne particulate matter (PM) concentrations have been measured, during the same episode, in comparison between the road verge and the garden area, presenting a substantial difference in the concentration levels, deducing that dense vegetation is protecting and blocking a majority of airborne PM. A literature highlight of health effects of different metal elements and PM concentrations is presented.

Directed evolution methods are becoming increasingly popular, as they are extremely powerful toward developing new biomolecules with altered/novel activities, e.g., proteins with new catalytic functions or substrate specificities, and nucleic acids that recognize an intended target. Especially useful are systems that have incorporated continuous evolution, where the protein to be evolved undergoes continuous mutagenesis to evolve a desired trait with little to no input from the researcher once the system is started. However, continuous evolution methods can be challenging to implement in the lab and daunting for researchers to invest time and resources. Our intent is to provide basic information and helpful suggestions that we have gained from our experience with bacterial phage-assisted continuous evolution (PACE). Specifically, we review factors to consider before adopting PACE for a given evolution scheme, different types of selection circuits that can be utilized with particular focus on the PACE-B1H selection system, what optimization of a PACE selection circuit may look like using directed evolution of ME47 as a case study, and additional techniques that may be incorporated into a PACE experiment. With this information, researchers will be better equipped to determine if PACE is a valid strategy to use to evolve their proteins and how to set up a valid selection circuit.

Cryosurgery has emerged as a promising method for harvesting veins, but the suitability of these cryostripped veins as grafts remains a subject of investigation. This study delves into uncharted territory by conducting an immunohistochemical analysis and exploring the molecular aspects of venous samples obtained through cryostripping. Existing literature lacks comprehensive data on the components of varicose veins' walls, particularly in relation to protein expression. Furthermore, little is known about the proliferation rate of endothelial cells within varicose veins, which we scrutinize alongside an assessment of CD34 endothelial reactivity. Materials and Methods: Our study encompassed 109 samples procured using the cryostripping method, which involves catheterizing veins with a specialized probe cooled to -85°C. Molecular profiling of the intima and endothelium was conducted using two key markers: CD34 and Ki67. Results: Immunoreactivity for CD34 was discernible across all three layers of the varicose vein walls that were excised using cryostripping. Notably, the endothelial cell layer exhibited intense and uniform positivity in 36 out of the 109 samples under investigation. In contrast, the results regarding Ki67 expression, whether pertaining to the intima or endothelium, remain inconclusive. Conclusions: Our findings advocate for the utilization of CD34 as a reliable marker to assess the morphological and molecular integrity of excised venous specimens. As the use of cryosurgery-harvested veins as grafts gains traction, this research contributes valuable insights into their potential viability for transplantation, opening new avenues for further exploration in the field of vascular surgery.

The purpose of this work is to present an adaptive sliding mode luenberger state observer with improved disturbance rejection capability and better tracking performance under dynamic conditions. The sliding hyperplane is altered by incorporating the estimated disturbance torque with the stator currents. Also, the effects of parameter detuning on the speed convergence is observed and compared with the conventional disturbance rejection mechanism. The entire drive system is first built in simulink environment. Then, the simulink model is integrated with RT-Lab blocksets and implemented in a relatively new real-time environment using OP4500 real-time simulator. Real-time simulation and testing platforms have succeeded offline simulation and testing tools due to their reduced development time. The real-time results validate the improvement in the proposed state observer and also correspond to the performance of the actual physical model.

The paper aims to introduce user-friendly modelling approaches to analyze how abiotic factors influence various trophic levels within the marine ecosystem, both naturally and through human impact. It specifically investigates the connections between environmental parameters (like temperature, salinity, and nutrients) and plankton along the Romanian Black Sea coast during the warm season (May-September) over a decade. Utilizing machine learning (ML) algorithms and data collected during this period, models were developed to project the proliferation of zooplankton. During the warm season, water temperature emerged as a significant factor affecting copepods and “other groups” zooplankton densities, while no discernible impact was noted on Noctiluca scintillans blooms. Salinity fluctuations notably influenced typical phytoplankton proliferation, with phosphate concentrations primarily driving widespread blooms. Two scenarios were explored for forecasting zooplankton growth: Business as Usual, predicting modest increases in temperature, salinity, and constant nutrient levels, and the Mild scenario, anticipating more substantial temperature and salinity increases while nutrients decrease significantly by 2042. The findings highlight that under both scenarios, Noctiluca scintillans displays notably high densities, with the second scenario projecting even higher values, surpassing the first by around 70%. These densities indicate characteristics of a eutrophic ecosystem, suggesting the potential implications of altered abiotic factors on ecosystem health.

Introduction: The assumption that food resources and dietary supplements are natural and do not have side effects, or do not interact with drugs, is wrong, and can lead to unplanned symptoms or even hospital admissions. Also, not communicating with the family doctor, or the pharmacist, can make their work considerably more difficult in establishing the correct treatment. Methods: PubMed, ResearchGate, EUR-Lex, and Memorial Sloan Kettering Cancer Center databases for scientific literature were analyzed, for the keywords "adverse reactions", nutrivigilance", and "drug interaction". The method proposed by us for the implementation of nutrivigilance in the re-search-development stage is the application and adaptation of HACCP principles (Hazard Analysis and Critical Control Points) to nutrivigilance. Results: The implementation of nutrivigilance in the Romanian food supplements industry and healthcare system represent a real tool for improving public health management by preventing adverse reactions, and reducing the costs of the health system. From our knowledge, the proposal regarding the implementation of nutrivigilance in the research stage of food and food supplements, based on the principles of HACCP is unique. Conclusions: We believe that the proposed method is useful starting with the research-development of food supplements, followed by post-sale analysis.

Asphaltenes constitute a heavy fraction of fossil fuels and their characterization is still a very difficult and challenging issue due to their complex and variable composition. Asphaltene components are highly condensed aromatic molecules having some heteroatom and aliphatic functionalities. Their molecular weights distribution span a wide range, from hundreds to millions of units, in dependence on the diagnostic used, leading to speculation about possible occurrence of self-aggregation. In the present work, mass spectrometry, with properly developed mathematical methods, size ex-clusion chromatography and X-ray diffraction analysis have been applied to asphaltenes for giving some further insight on their MW distribution and characteristics. The results here reported give further quantitative support to the experimental data interpretation already reported in previous works.

Low back pain is a common problem in the active population, and the second reason for visiting a physician. In patients with lumbar disc protrusion, the nucleus pulposus bulges against the disc and the latter protrudes into the spinal column, but the annulus fibrosus remains intact. The purpose of this study was to prove that starting an early complex rehabilitation treatment results into pain and disability reduction, and increased muscle strength and mobility in patients with lumbar disc protrusions. We performed a prospective cohort study, enrolling 60 patients (25 men and 35 women) aged between 26 to 76 years, diagnosed with lumbar disc protrusion. Patients in the experimental group registered significant improvements in all studied variables (pain, mobility, muscle strength, disability) after 6 months of treatment. The results of our study suggest that, in the lumbar disc disease, a combined rehabilitation program may be more effective in terms of pain and disability reduction, if it starts early after diagnosis. The current study proves the importance of combining electrotherapy with hydrotherapy and physical therapy. Patients who received this treatment combination showed an extremely significant improvement in pain relief, and reduction of functional disability after 6 months of treatment.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

Micro and small wood-processing enterprises represent the heart of the European forest-based industries, being among the key drivers of economic growth in rural, mountainous, and poor regions. Their economic efficiency is of fundamental importance for their existence and the pro-vision of income for the local population in rural areas. Data Envelopment Analysis (DEA) is nonparametric, linear-programming-based approach, commonly used to analyse the efficiency of organizational units. This method allows estimating the economic efficiency of a certain eco-nomic system without assumptions about the functional form between resources and products. Furthermore, DEA determines the efficiency frontier and gives results of whether an enterprise, i.e., a Decision Making Unit (DMU) is efficient or not. The main objective of this study was to investigate and evaluate the economic efficiency of micro and small wood-processing enterpris-es in the EU countries and reveal the hidden inputs that facilitate efficiency generation. The eco-nomic efficiency evaluation was carried out on the basis of the official statistical data for the mi-cro and small wood-processing companies in the EU member states for the period 2015-2020 by performing a two-stage DEA analysis. The data used were standardized by value per employee. In addition to the first stage of DEA, fractional regression probit and logit models with four contextual variables were used to reveal the influence of the hidden inputs in the model. The results showed that the micro and small wood-processing enterprises can be regarded as more scale-efficient than technically-efficient entities. The only contextual variable affecting the eco-nomic efficiency was Investments per Person Employed, improving the efficiency by 2% per 1% increase of the investments.

We present set-theoretical solutions of the Yang-Baxter equation in BCK–algebras. Some solutions in BCK−algebras are not solutions in other structures (such as MV −algebras). Related to our investigations we also consider some new structures: Boolean coalgebras and a unified braid condition – quantum Yang-Baxter equation. Finally, we will see how poetry has accompanied the development / history of the Yang–Baxter equation.

This study examines the effectiveness of a comprehensive psychomotor development program combined with adapted football training for adolescents diagnosed with intellectual disabilities in Romania. Twelve participants, with a mean age of 17.42 years underwent a carefully designed intervention program spanning 36 weeks. The program aimed to enhance fundamental movement skills, integrate these skills into specialized football training, and culminate in a Unified 7-a-side Football Match. Results indicate significant improvements in psychomotor skills, including static and dynamic balance, pulse processing speed, and identified stimuli. Moreover, the intervention positively impacted social interaction among participants. Statistical analysis, employing Pearson Correlation Analysis and Paired Samples t-Test (One-Sample), compared assessments. Results revealed significant differences between pre- and post-intervention measurements, providing robust evidence of the program's efficacy. The positive correlations between physical parameters and social interaction highlight the interconnectedness between physical fitness and social engagement. Our findings suggest that improvements in physical abilities may contribute to increased social interaction among children with intellectual disabilities, underscoring the holistic nature of our intervention, which addresses multiple dimensions of development simultaneously. The findings underscore the holistic benefits of integrating psychomotor development and adapted football programs for adolescents with intellectual disabilities, emphasizing the importance of promoting inclusive physical activities for their overall well-being.

In this paper, the extraction of essential oil (EO) from thyme by consecutive use of ultrasound and microwave treatments is presented. The aim of the study was to apply an ultrasound pre-treatment of thyme leaves to enhance the thymol content and the extraction yield of the EO obtained by microwave-assisted hydro-distillation (MWHD). Compared with the conventional hydro-distillation (CHD), the consecutive use of ultrasound and microwave treatments resulted in a 72% lower extraction time. When the ultrasound pre-treatment (using the ultrasonic processor with an amplitude of 70%) was applied, the EO content was 23% higher compared to the extraction without pre-treatment. The EO samples were analyzed by GC/MS. The results showed that the major component, thymol, varied from 43.54% (by CHD) to 65.94% (by consecutive use of ultrasound and microwave treatments).

In this research paper, a hybrid Artificial Neural Network (ANN)-Fuzzy Logic Control (FLC) tuned Flower Pollination Algorithm (FPA) as a Maximum Power Point Tracker (MPPT) is employed to emend root mean square error (RMSE) of photovoltaic (PV) modeling. Moreover, Gaussian membership functions have been considered for fuzzy controller design. This paper interprets Luo converter occupied brushless DC motor (BLDC) directed PV water pump application. Experimental responses certify the effectiveness of the suggested motor-pump system supporting diverse operating states. Luo converter is newly developed dc-dc converter has high power density, better voltage gain transfer and superior output waveform and able to track optimal power from PV modules. For BLDC speed controlling there is no extra circuitry and phase current sensors are enforced for this scheme. The recentness of this attempt is adaptive neuro-fuzzy inference system (ANFIS)-FPA operated BLDC directed PV pump with advanced Luo converter has not been formerly conferred.

Due to the content of biologically active substances, sea buckthorn (Hippophae rhamnoides L.) is of growing interest to scientists, the food industry, pharmaceuticals, cosmetology and consumers. The aim of this study is to investigate the correlation between the chemical composition (Carotenoid content (CC), Ascorbic acid content (AAC), Total dry matters (TDM), Titratable acidity (TA), pH, Organic acids (OA)) and the Antibacterial effect (AA) (Diameter of the inhibition zone in mm of Bacillus pumilus) of four species of sea buckthorn (Clara, Dora, Cora, Mara), cultivated in the Republic of Moldova. The sea buckthorn species tested was found to have a different Carotenoid content (1.79±0.43 … 48.92±0.61 mg/100g), Ascorbic acid content (74.36±0.60 … 373.38±2.29 mg/100g), Organic acids (malic acid 5.8±0.02 ... 13.4±0.01 mg/100g, citric acid 0.08±0.00 ... 0.32±0.01 mg/100g, succinic acid 0.03±0.00 ... 1.1±0.00 mg/100g), Total dry matters (16.71±0.05 … 24.54±0.09 %), Total acidity (2.15±0.05 ... 8.76±0.00 %), and pH value (2.73±0.02 ... 3.00±0.07). The microbial activity of sea buckthorn, evaluated by the diameter of the inhibition zone, constituted for Bacillus pumilus (3.70…15.91mm/g-1 for whole sea buckthorn fruits and respectively 13.33…26.67 mm/g-1 for sea buckthorn puree).

Critically ill patients with sepsis require a multidisciplinary approach, as this situation implies multiorgan distress, with most of the bodily biochemical and cellular systems being affected by the condition. Moreover, sepsis is characterized by a multitude of biochemical interactions and by dynamic changes of the immune system. At the moment, there is a gap in our understanding of the cellular, genetic, and molecular mechanisms involved in sepsis. One of the systems intensely studied in recent years is the endocannabinoid signaling pathway, as light was shed over a series of important interactions of cannabinoid receptors with biochemical pathways, specifically for sepsis. Furthermore, a series of important implications on inflammation and the immune system that are induced by the activity of cannabinoid receptors stimulated by the delta-9-tetrahidrocannabinol and cannabinol have been noticed. The aim of this review paper was to present, in detail, the important mechanisms modulated by the endocannabinoid signaling pathway, as well as of the molecular and cellular links it has with sepsis. At the same time, we wish to present the possible implications of cannabinoids in the most important biological pathways involved in sepsis, such as inflammation, redox activity, immune system, and epigenetic expression.

Background and Objectives: Romania ranks among the countries with a notably high rate of preventable deaths due to inadequacies in prevention, screening, early detection, and timely management processes. Cervical cancer (CC) is a significant contributor to these preventable deaths, particularly affecting patients from marginalized backgrounds, rural regions, and the Roma population. The purpose of this article was to identify correct and consistent information of the Roma population about the risk of CC, as well as the importance of understanding the causes of the disease and awareness of the available prevention methods. Materials and methods: A cross-sectional study was conducted using a self-administered questionnaire applied only to Roma women in Romania. Results: We enrolled 759 patients in the study. These were divided into 2 groups, Group 1 comprised 289 (38.1%) women who had been tested for HPV infection, while Group 2 included 470 (61.9%) women who had never been tested for HPV infection. Characterization of women in Group 1: mostly aged between 25-54 years, with high school education, married, who started sexual activity under the age of 18 years, with only one sexual partner and with over 5 pregnancies. Regarding contraceptive methods, 35.7% of women do not know/ use any contraceptive method, and 32.2% use hormonal contraceptives. Two thirds of the women tested had heard of HPV, and 19.7% were vaccinated against HPV with at least 2-3 doses. A percentage of 8.7 had a diagnosis of CC, compared to those who were not tested (p-0.0001), whereas 63% of the tested women do not know much about CC, as opposed to 85.7% of the group of untested women. Conclusion: Cervical cancer (CC) continues to be a public health issue in Romania, particularly in patients belonging to vulnerable groups. Promotion campaigns for HPV vaccination and CC screening are necessary to reduce the associated mortality and morbidity.

The research is focusing on analyzing the concentrations of particulate matter (PM) next to a highly congested road section, with 39,900 as a maximum number of vehicles per 24 h, in the vicinity of Timisoara, Romania. Concentrations have been measured in multiple episodes using two different measurement methods, gravimetric and dynamic light scattering, showing a disperse range of PM concentrations. Presence of metal particles in the samples have been analyzed using an electron microscope. Additionally, impact on human health is described by evaluating results for inhalable, thoracic, and alveolar sized particles.

The pennate diatom Phaeodactylum tricornutum is a model organism able to synthesize industrially-relevant molecules. Commercial-scale cultivation currently requires large monocultures, prone to bio-contamination. However, little is known about the identity of the invading organisms. To reduce the complexity of natural systems, we systematically investigated the microbiome of non-axenic P. tricornutum cultures from a culture collection in reproducible experiments. The results revealed a dynamic bacterial community that developed differently in “complete” and “minimal” media conditions. In complete media, we observed an accelerated “culture crash”, indicating a more stable culture in minimal media. The identification of only four bacterial families as major players within the microbiome suggests specific roles depending on environmental conditions. From our results we propose a network of putative interactions between P. tricornutum and these main bacterial factions. We demonstrate that, even with rather sparse data, a mathematical model can be reconstructed that qualitatively reproduces the observed population dynamics, thus indicating that our hypotheses regarding the molecular interactions are in agreement with experimental data. Whereas the model in its current state is only qualitative, we argue that it serves as a starting point to develop quantitative and predictive mathematical models, which may guide experimental efforts to synthetically construct and monitor stable communities required for robust upscaling strategies.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

This study aimed to investigate Romanian physicians' awareness, recommendation practices, and opinions regarding using Foods for Special Medical Purposes (FSMPs) products. A total of ten physicians were interviewed using a structured questionnaire, and their responses were analysed using thematic content analysis. The study found that physicians were aware of FSMPs and recommended them to their patients based on nutritional deficits, weight loss, or deglutition impairments. In addition, disease stage, treatment scheme, taste, affordability, and availability were identified as factors influencing the recommendation and use of FSMPs. While physicians generally did not consult clinical trials, clinical experience was deemed essential for recommending FSMPs to patients. Patients' feedback regarding the usage and sourcing of FSMPs was generally positive, with some expressing concerns about the availability of different flavours and the costs of purchasing the products. The study concludes that physicians play a vital role in recommending FSMPs to patients and ensuring they have the necessary nutritional support during treatment. However, more patient education materials and collaboration with nutritionists may be required to improve patient outcomes and reduce patient financial burden.

The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

In this paper we propose a simple procedure to obtain multi-walled carbon nanotubes (MWCNT) decorated with TiO₂-Ag nanoparticles (MWCNT-TiO₂-Ag). MWCNT were decorated with TiO2-Ag via combined functionalisation with -OH and –COOH groups and polymer wrapping technique using poly(allylamine hydrochloride) (PAH). TiO₂ modified Ag nanoparticles were synthesized through Pechini method using mixture of acetylacetonate-modified titanium (IV) isopropoxide with silver nitrate (the Ag+/Ti4+ atomic ratio, is 0.5, 1,0, 1.5, 2.0 and 2.5 %, respectively) and the L(+)-ascorbic acid, as reducing agents. XRD analysis revealed the formation of nanocomposite containing CNT, TiO₂ (anatase and rutile) and Ag. By SEM was evidenced the presence of the nanoparticles on MWCNT surface. The increases of the ratio between Ag⁺ and Ti⁴⁺ decrease the band gap energy of the samples. In Raman spectra the characteristic vibration of the TiO₂, Ag and C atoms of graphite are identified. The photocatalytic activity of the MWCNT-TiO₂-Ag nanocomposite was assessed by examining the degradation of Allura red (E129) aqueous solution under UV irradiation. The dye photodegradation process follows a pseudo – first – order kinetic with respect to the Langmuir – Hinshelwood reaction mechanism.

Chronic lymphocytic leukemia (CLL) is a distinct category of lymphoproliferative disorder characterized by the clonal expansion of mature B cells, followed by their accumulation in primary and secondary lymphoid organs. Cluster of differentiation (CD) markers such as CD20, CD22, CD23, CD5, and CD81 serve as reliable prognostic indicators and disease progression factors in CLL. The human leukocyte antigen (HLA) system is a critical genetic variable in many diseases, with well-documented associations between HLA and various cancers. This study aims to investigate, for the first time, potential connections between HLA typing and CD marker expression in CLL. Despite being one of the most prevalent neoplasms in developed regions, there is a need for biomarkers that can improve survival predictions and identify possible genetic determinants. Methods: This study included 66 CLL patients and 100 controls, with all samples analyzed using biochemical methods, flow cytometry, and cytomorphology. Next-generation sequencing (NGS) was performed for HLA typing. Results: The results indicate that several CD markers are statistically associated with different HLA alleles. Specifically, CD20 was associated with HLA-DRB1*11:04:01; CD45 with HLA-C*07:01:01; CD79b with HLA-DPA1*02:01:02; CD23 with HLA-B*39:01:01; CD43 with HLA-DRB1*15:01:01; CD22 with HLA-B*49:01:01, HLA-C*07:01:01, HLA-DPB1*02:01:02, and HLA-DRB1*07:01:01; and CD81 with HLA-DPB1*04:02:01, HLA-DQA1*01:04:01, and HLA-DQB1*05:03:01.Conclusion: In conclusion, this research demonstrates significant statistical links between HLA genes and immunophenotypic markers in CLL patients, shedding new light on the immunological context of CLL.

The assessment of soil contamination in the vicinity of integrated siderurgical plants is of outmost importance for agroecosystems and human health, and sensitive techniques should be employed for accurate assessment of chemical elements (metals, potential toxic elements, rare earths, radioelements) in soil and further evaluation of potential ecological and safety risk. In this paper a total of 45 major, minor and trace elements (Al, As, Au, Ba, Br, Ca, Cd, Ce, Co, Cr, Cs, Cu, Dy, Eu, Fe, Hf, Hg, I, K, La, Mg, Mn, Mo, Na, Nd, Ni, Pb, Rb, Sb, Sc, Sm, Sn, Sr, Ta, Tb, Th, Ti, Tm, U, V, W, Y, Yb, Zn and Zr) were quantified in soils located around a large siderurgical works (Galati, SE Romania) using instrumental neutron activation analysis (INAA) in combination with X-ray fluorescence (XRF) and inductively coupled plasma mass spectrometry (ICP-MS). The statistical analysis results and vertical distribution patterns for three depths (0-5 cm, 5-20 cm, 20-30 cm) indicate inputs of toxic elements in the sites close to the ironmaking and steelmaking facilities and industrial wastes dumping site. For selected elements, a comparison with historical, legislated and world reported concentration values in soil was performed and depth migration, contamination and toxic risk indices were assessed. The distribution of major, rock forming elements was closer to the Upper Continental Crust (UCC), and to the Dobrogea loess, finding confirmed by the ternary diagram of the incompatible trace elements Sc, La and Th, as well as by the La to Th rate. At the same time, the La/Th vs. Sc and Th/Sc vs. Zr/Sc bi-plots suggested a felsic origin and a weak recycling of soils mineral components.

Cardiac autonomic neuropathy (CAN) is a severe complication of diabetes mellitus (DM) strongly linked to a nearly five-fold higher risk of cardiovascular mortality. Patients with Type 2 Diabetes Mellitus (T2DM) are a significant cohort in which these assessments have particular relevance to the increased cardiovascular risk inherent in the condition. This study aimed to explore the subtle correlation between the Ewing test, Sudoscan-cardiovascular autonomic neuropathy score, and cardiovascular risk calculated using SCORE 2 Diabetes in individuals with T2DM. The cohort consisted of 211 patients diagnosed with T2DM with overweight or obesity without established ASCVD, aged between 40 to 69 years. The prevalence of CAN in our group was 67.2%. In the study group, according SCORE2-Diabetes, four patients (1.9%) were classified with moderate cardiovascular risk, thirty-five (16.6%) with high risk, and one hundred seventy-two (81.5%) with very high cardiovascular risk. On multiple linear regression, the SCORE2-Diabetes algorithm remained significantly associated with Sudoscan CAN-score and Sudoscan Nephro-score and Ewing test score. Testing for the diagnosis of CAN in very high-risk patients should be performed because approximately 70% of them associate CAN. Increased cardiovascular risk is associated with sudomotor damage and that Sudoscan is an effective and non-invasive measure of identifying such risk.

Background and Objectives: The purpose of this study was to investigate whether early surfactant administration affects the status of ductus arteriosus (DA) in preterm infants ≤32 weeks of gestational age (GA) within 24 hours of birth. Materials and Methods: It is a prospective study conducted from March 15, 2022, to November 15, 2023, in a tertiary academic center. In-born infants ≤ 32 weeks of gestation (n = 88) were enrolled. The study group was further divided into surfactant (n=44) and non-surfactant (n=44) subgroups. Results: 76% of the preterm infants who received surfactant therapy (RRR = 0.839) recorded an increase in Kindler Score at 24 hours of life (1-RR = 1-0.24 = 76%). Surfactant administration was significantly associated with decreased pre-ductal diastolic pressure (29.9 mmHg vs. 34.8 mmHg, p=0.0231), post-ductal diastolic pressure (28.7 mmHg vs. 32.2 mmHg, p=0.0178) pre-ductal MAP (41.6 mmHg vs. 46.5 mmHg, p=0.0210) post-ductal MAP (41.0 mmHg vs. 45.3 mmHg, p=0.0336). There were no significant changes in ductus arteriosus parameters at 24 hours of life. Conclusions: Early surfactant administration does not affect the status of ductus arteriosus in preterm infants ≤32 weeks of gestational age at 24 hours of life.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.

According to cancer death rates for women worldwide, this form of cancer ranks fourth after breast, bronchopulmonary, and colorectal cancer, affecting around 570,000 women annually. About 270,000 women each year pass away from this illness, 85% of them are from underdeveloped nations where cervical cancer claims more lives than any other kind of cancer. In Romania, cervical cancer ranks fourth in terms of death, behind breast, bronchopulmonary, and colorectal cancers, and second in terms of incidence, behind breast cancer. Endometriosis in the cervical region is quite uncommon. Only a tiny fraction of women had the condition upon diagnosis. It might be challenging to detect cervical endometriosis since it rarely manifests any symptoms or markers. Women who are asymptomatic can manage the condition expectantly; however, if the symptoms return often, surgery may be required. As many patients have concurrent diseases such fibroids, adenomyosis, ovarian cysts, and pelvic endometriosis, cervical endometriosis therapy appears to be straightforward. There ought to be surgical intervention. Symptomatic cervical endometriosis, such as irregular or post-coital bleeding, may be treated surgically using the LLETZ surgery or another cervical ablation approach. Background and Objectives: (1) To assess one's degree of knowledge on the signs, causes, and methods of preventing cervical cancer or cervical endometriosis, as well as screening for these conditions. (2) To ascertain how the responder behaves about cervical cancer screening and prevention, as well as endometriosis in the cervical region. Materials and Methods: A case report about cervical cancer or cervical endometriosis was conducted among a patient from Romania, Timisoara. Results: In this study, we report the patient with cervical endometriosis, although he was initially diagnosed with cervical cancer. Conclusions: Cervical cancer, a condition that can have serious repercussions on the patient's health, even if there is no clear picture of paraclinical investigations, to raise the suspicion of cervical endometriosis and not cervical cancer.

The importance of small urban green areas has increased in the context of rapid urbanization and densification of the urban tissue. The analysis of these areas through remote sensing has been limited due to the low spatial resolution of freely available satellite images. We propose a timeseries analysis on 3 m resolution Planet images, using GEOBIA and vegetation indices, with the aim of extracting and assessing the quality of small urban green areas in two different climatic and biogeographical regions – temperate (Bucharest, Romania) and mediterranean (Athens, Greece). Our results have shown high accuracy (over 91%) regarding the extraction of small urban green areas in both cities, across all analysed images. The timeseries analysis showed consistency in location for around 55% of the identified surfaces throughout the entire period. The vegetation indices registered higher values in the temperate region, due to the vegetation characteristics and the planning of the two cities. For the same reasons, the increase in vegetation density and quality, as a result of the distance from the city centre and the decrease in the density of built-up areas is more obvious in Athens. The proposed method provides valuable insights in the distribution and quality of small urban green areas at city level and can represent the ground basis for many analyses, currently limited by poor spatial resolution.

Cobalt ferrite nanoparticles (NPs) doped with rare earth (RE) metals with general formula CoFe_2-xRE_xO₄ (RE=Yb, Dy, Gd; x = 0.0 - 0.3) were synthesized by the co-precipitation method followed by post thermal treatment. The influence of RE doping on structural, magnetic and thermal properties and potential biomedical applications like magnetic hyperthermia has been investigated. In the as-prepared samples RE cations enter the spinel lattice as detected by X-ray diffraction. Thermal treatment leads to thermodynamically stable and relaxed single-phase spinel structures only for lower RE content, x = 0.01-0.05. However, annealed samples present higher mass magnetization values (M_S), up to 83 Am²/kg. RE content also affects M_S, especially in the case of annealed samples where it decreases linearly with x from about 80 Am²/kg (x = 0.01) to about 60 Am²/kg (x = 0.30). Thermal treatment induces a reduction in coercivity from 60-100 mT for as-prepared samples to 18-33 mT for annealed samples, in a nonlinear manner with respect to RE content. Heating efficiency, i.e., Specific Loss Power (SLP), of all samples has been studied using both magnetometric and calorimetric method to deeper examine the energy loss mechanisms involved.

The paper combines two new original concepts about eco-energetic systems. The first one is related to the M.E.N. (Mega-Eco-Nega-Watt) paradigm, which is based on three different but complementary ecological economic spaces: MEGAWATT, as needed energy, ECOWATT, as ecological energy, and NEGAWATT, as preserved energy, even the renewable energies and technologies, in the context of electrical energy production. The second concept presented in this paper is the eco-energetic efficiency, introduced in order to facilitate a correlation between the energetic efficiency of the system and a necessary, new defined ecological coefficient. The proposed formula for eco-energetic efficiency enables an interesting form of reporting to the different situations in which the input energy, output energy, lost energy and externalities, involved in an energetic process interact to produce energy in a specific energetic system, in connection with the circular economy model. Finally, is presented an original diagram of the energetic chains to produce electricity in a resilience regim, with high eco-energetic efficiency from originating in different primary energetic sources as external (gravitation & solar sources), fuels (classical & radioactive), internal sources and others. Even what kind of energetic sources are used to obtain electricity, as coals, gas, wood, hydropower, nuclear power, wind power, biomass, solar systems, and others, the entire process should be sustainable in what is the transdisciplinary integration of the different representative spheres as energy, socio-economy, ecology (environment), with the main core, sustainable education, inclueding the law and administrative aspects, as necessary fields of the knowledge based society/economy.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

Keywords: Trichoderma sp., biogenic selenium nanoparticles, capping biomolecules, bio-corona, agriculture, plant biostimulants, phytopathogens, physicochemical properties, bioactivity mechanism

Life Cycle Cost Analysis is a method used to assess long-term economic efficiency among equivalent competing processes or products. The purpose of the paper is to investigate the nature and level of costs for an organic orchard located in Southern Romania, using a complex approach covering the entire chain of production, through the life span. The research results, based on a dynamic analysis and an integrated evaluation of the orchard's performance, have been ranked on investment and operational costs, broken down on three categories (establishment and production, post-harvest and transport costs). The highest cost, representing 151726 euros/ha/20 years, about 52.72% of the total operational costs and 50.4% of the total farm costs/ha/20 years, was recorded in exploitation stage. The scenarios for the sensitivity analysis considered different levels of average yield (40, and, respectively 60 tons/ha) with different rate of sold production (85%, optimistic scenario; 70%, pessimistic scenario). The hotpoints identified at the production stage were use of agricultural machinery, several pesticides, the costs of seedlings, anti-hail net, plastic boxes and labor cost, while at the post-harvest stage, were those related to labor and energy consumption. The transport stage has had important costs with tractor operation and the track.

Penetration of grid connected inverters (GCI) has arisen in power systems due to increasing integration of renewable sources. However, restrictive grid codes require that renewable sources connected to the grid with power electronic systems must be properly connected and appropriate currents must be injected to support stability of the grid under grid faults. Simultaneous injection of symmetrical positive and negative sequence currents is mandatory to support stabilization of grid at the instant of grid faults. Conventional synchronously rotating frame dq current controllers are insufficient under grid faults due to low bandwidth of PI controllers. This paper proposes a new grid current control strategy for grid connected voltage source inverters under unbalanced grid voltage conditions. A proportional current controller with a first order low pass filter disturbance observer (DOb) is proposed which establishes positive sequence power requirements and independently control negative sequence current components under unbalanced voltage conditions. The method does not need any parameter, since it estimates nonlinear terms with low pass filter DOb. Simulations are implemented in Matlab/Simulink platform demonstrating the effectiveness of proposed method.

This comprehensive scientific review provides an in-depth analysis of both the natural compounds, pyrethrins, and their synthetic derivatives, pyrethroids, focusing on their classification, biosynthesis, mechanism of action, general and pharmaceutical uses, as well as their toxicity and environmental impact. Pyrethrins, derived from certain plant species, have long been recognized for their potent insecticidal properties. The review begins by examining the classification of pyrethrins and pyrethroids, elucidating their structural characteristics and unique features within the field of natural and synthetic compounds. The biosynthetic pathways responsible for producing pyrethrins in plants are discussed, highlighting the enzymatic reactions and genetic regulation involved. In addition, the synthesis of pyrethroid derivatives is explored, including both natural and synthetic sources and potential optimization strategies. Understanding the mechanisms of action by which pyrethrins and pyrethroids exert their insecticidal effects is a crucial aspect of this review. Complex interactions with the nervous systems of target organisms are examined, providing insights into their selective toxicity and modes of action. In addition, the various applications of these compounds are explored, from their use in agriculture for pest control to their incorporation into household insecticides and potential pharmaceutical applications. The review also critically evaluates the potential toxicity of pyrethrins and pyrethroids to human health. By consolidating current knowledge and research findings, this review provides a comprehensive understanding of the properties and applications of pyrethrins and pyrethroids, highlighting their benefits and risks, and the importance of responsible and sustainable use in various areas.

During the last decades, a growing number of studies have shown that infections during pregnancy have an important impact on both pregnant women and their fetuses. Our goal was to identify newborns from pregnancies with SARS-CoV-2 infection and to investigate the extension of neonatal complications using cardiac, abdominal and cerebral ultrasonography, hearing testing and indirect ophthalmoscopy. By contrast, neonates whose mothers were vaccinated against COVID-19 during pregnancy and those from pathology-free pregnancies have been examined. A total of 458 newborns were included, over a period of 10 months, divided into 3 groups, COVID-19 group, vaccine group and control group. Although 6 cardiac malformations were found in the COVID-19 group, no correlation was made compared to the vaccine and control group (p=0.07). Grade 1 intraventricular hemorrhage and hypoxic ischemic encephalopathy were the most prevalent among neonates from mothers with SARS-CoV-2 infection (p=0.002 and p&lt;0.001, respectively). The kidney anomaly found to be most frequent in this group was grade 1 unilateral hydronephrosis (p&lt;0.001). COVID-19 disease during the gestational period had no effect on the auditory or visual function. Despite the fact that our observations are relevant, further studies investigating the effects of SARS-CoV-2 infection during pregnancy and the neonatal outcomes are necessary.

Background: The enduring psychological effects of the COVID-19 pandemic continue to affect individuals long after the immediate health concerns have subsided. This research aims to identify specific groups within the Romanian population who are at a higher risk of experiencing mental health challenges that can interfere with everyday life and may lead to more serious mental health disorders. Methods: Conducted as a cross-sectional survey, this study evaluated the prevalence and intensity of psychological distress using the DASS-21 questionnaire. An online survey distributed via Google Forms also gathered socio-demographic data and COVID-19-specific information. Statistical analyses included the Shapiro-Wilk test, Fisher's exact test, and Z-tests with Bonferroni correction. Quantitative independent variables that lacked a normal distribution were compared between groups using either the Mann-Whitney U test or the Kruskal-Wallis H test. Results: Analysis of 521 questionnaires, filled out by a predominantly middle-aged cohort of 320 women and 201 men, revealed that 63.72% of participants worked outside the healthcare field. Those unemployed or retired reported significantly higher anxiety levels than individuals in other sectors. Moreover, living alone, experiencing the loss of close relatives (6.14%) or friends (33.59%), and undergoing hospitalization or reinfection due to COVID-19 were linked to significantly elevated distress scores. Conclusion. By identifying the segments of the population most vulnerable to psychological distress, as evidenced by higher scores among the unemployed, retirees, individuals living alone, and those directly affected by COVID-19 through personal health or loss, targeted initiatives for psychological screening and therapy can be established. Such measures are essential for enhancing the post-pandemic mental well-being of Romanians, addressing the specific needs uncovered in this study.