The combined heat and power system is based on the principle of "cascade utilization of thermal energy" for system integration and optimization. The rational utilization of energy, as well as the rational arrangement of energy flow and the process optimization combination of the overall system are taken into account in order to achieve multifunctional goals in the field of thermal engineering. The present paper presents a detailed assessment of combined heat and power systems from above standpoints. This article is divided into two parts “CHP based on thermo-dynamic cycles” and “CHP based on non-thermodynamic cycles”. Each part is then classified based on power subsystem energy consumption efficiency (high or low), including Rankine cycle, ORC, Stirling cycle, gas turbine, reciprocating engine, PVT and fuel cell. The present paper also helps identify the research gaps in this area and provides direction on future studies on combined heat and power systems.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

The rapid development of new retail and the impact of COVID-19 have catalyzed the blowout growth of community group purchasing. The emergence of community group purchasing collection and delivery points (CGPCDPs) has become a new way to solve the "last mile" problem of new retail delivery. Based on the point of interest (POI) data of CGPCDPs of Nansha District, Guangzhou City, this study uses text analysis, spatial analysis, model analysis, and other methods to analyze the operation mode, spatial distribution, and influencing factors of CGPCDPs. The conclusions are as follows: CGPCDPs initiators are mainly shopkeepers. They depend mainly on wholesale and retail shops. Service targets are mainly urban and rural communities, followed by industrial areas. The distribution of CGPCDPs has apparent spatial differentiation. At the macro scale, it shows the characteristics of "central agglomeration and peripheral dispersion". It is distributed along the "northwest-southeast" direction and presents a "dual-core multi-center" pattern. At meso-micro scale, different built environments in developed areas of cities, villages in the city (ChengZhongCun) and rural areas show distinct distribution patterns. The MGWR regression model has a better fitting effect than OLS and GWR. The main influencing factors are population density, construction land, house price, supporting place, residence density, urban community, and road proximity.

This study investigated the influence and interaction of tobacco promotional and control information with adolescents’ current smoking and smoking susceptibility. 12,278 students were recruited from junior, senior and vocational high schools located in Shanghai, China. The exposure to tobacco promotional and control message of participants over the past 30 days were examined, as well as current smoking and never smokers’ initiation susceptibility. Complex sample analysis was applied. Descriptive and multivariate logistic regressions were conducted. 89.3% and 91.5% of adolescents investigated were exposed to tobacco promotional and control message respectively, which separately increased and decreased the risk of current smoking and never-smokers’ smoking susceptibility, especially among males and junior high school students. The risk changed in consistency with the exposure level（P_trend < 0.001）. Tobacco control message seemed to mitigate the influence of tobacco promotions in the risk of both current smoking (OR = 0.64, 95%CI: 0.41–0.99) and smoking susceptibility (OR = 0.65, 95%CI: 0.46–0.93). Tobacco-related message exposure was highly prevalent and associated with youth smoking risk and smoking susceptibility. It is important to enhance the comprehensiveness and enforcement of promotion bans. Given the improvement of tobacco control message on smoking risk brought by tobacco promotions, the publicity and dissemination of tobacco control information need to be consistently strengthened.

The land subsidence occurring in goafs after coal mining is a protracted process. The accurate prediction of long-term land subsidence in goafs relies heavily on the availability of long-term monitoring data. However, the scarcity of continuous long-term land subsidence monitoring data subsequent to the cessation of mining significantly hinders the accurate prediction of long-term land subsidence in goafs. To address this challenge, this study proposes an innovative method based on Interferometric Synthetic Aperture Radar (InSAR) for predicting long-term land subsidence of goafs following coal mining. The proposed method employs a concatenation approach that integrates multiple short-term monitoring data from different coal faces, each with distinct cessation times, into a cohesive and uniform long-term sequence by normalizing the subsidence rates. The method was verified using actual monitoring data from the Yangquan No.2 mine in Shanxi Province, China. Initially, coal faces with same shapes but varying cessation times were selected for analysis. Using InSAR monitoring data collected between June and December of 2016, the average subsidence rate corresponding to the duration after coal mining cessation of each coal face was back-calculated. Subsequently, a function relating subsidence rate to the duration after coal mining cessation was fitted to the data. Finally, the relationship between cumulative subsidence and the duration after coal mining cessation was derived by integrating the function. The results indicated that the relationship between subsidence rate and duration after coal mining cessation followed an exponential function for a given coal face, whereas the relationship between cumulative subsidence and duration after coal mining cessation conformed to the Knothe time function. Notably, after the cessation of coal mining, significant land subsidence persisted in the goaf of the Yangquan No.2 mine for a duration ranging from 5 to 10 years. The cumulative subsidence curve along the long axis of the coal face ultimately exhibited an inclined W-shape. The proposed method enables the quantitative prediction of residual land subsidence in goafs, even in cases where continuous long-term monitoring data are insufficient, thus providing valuable guidance for construction decisions above the goaf.

Purinergic signaling is that nucleotides (especially ATP) and adenosine are utilized as transmitter molecules, which play an important role in the immune system. In the extracellular ventricle, ATP plays a significant role of pro-inflammatory molecules mainly through activating P2 receptors, while adenosine plays the role of anti-inflammatory molecules mainly through activating P1 receptors. As we know，neutrophils are the most abundant immune cells in our circulation and have become an essential part of coordinating a series of complex events during inflammatory diseases. However, due to the destruction of inflammatory substances from neutrophils, the activation of neutrophils is fine-tuned, and purinergic signaling is associated with this process. As a matter of fact, altering the balance between P2 and P1 signals is of great importance for neutrophils to exert immune activities properly. Here, we review the role of purinergic signaling in regulatory function of neutrophils during inflammatory disease, and then discuss the potential contribution of targeted purinergic signals in the treatment of the neutrophil during inflammatory diseases.

Dayaoshan, as an important metal ore producing area in China, is faced with the dilemma of resource depletion due to long-term exploitation. In this paper, remote sensing method is used to circle the favorable metallogenic areas and find new ore points for Gulong. Firstly, vegetation interference bas been removed by using mixed pixel decomposition method with hyperplane and genetic algorithm (GA) optimization; then, altered mineral distribution information has been extracted based on principal component analysis (PCA) and support vector machine (SVM) method; Thirdly, the favorable areas of gold mining in Gulong has been delineated by using ant colony algorithm (ACA) optimization SVM model to remove false altered minerals; Lastly, field survey verified that the extracted alteration mineralization information is correct and effective. The results show that the mineral alteration extraction method proposed in this paper has certain guiding significance for metallogenic prediction by remote sensing.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

In crystal structure prediction, Newton's second law can always be applied to particles (atoms or ions) in a cell to determine their positions. However the values of the period vectors (crystal cell edge vectors) should be determined as well. Here we applied the dynamical equations of period vectors derived recently based on Newton's laws (doi:/10.1139/cjp-2014-0518) for that purpose, where the period vectors are driven by the imbalance between the internal and external pressures/stresses. For equilibrium states, they became equations of state, which essentially turn out the equilibrium conditions of crystals from mechanical point of view. For external pressure, by ignoring some effects, they reduced to the Mie-Gruneisen equation. Since the internal stress has both a full kinetic energy term and a full interaction term, the influences of both external temperature and stress/pressure on crystal structures can be calculated, then thermodynamical properties and processes were presented. Contrary to usual ideas, the equations show that pure harmonic vibrating phonons can result in thermal expansion in crystals when the external temperature is changed. Finally, crystal system collapse due to temperature and/or stress/pressure change was discussed.

This paper aims to quantify the influence of hydrogen embrittlement on Wierzbicki and Xue (W-X) model parameters. This model has 4 parameters which have been obtained by tensile tests on smooth specimens, tensile notch specimens, single notch tensile specimens (SENT) and pure shear specimens. Hydrogen embrittlement has been obtained by electrolytic method. Application of the (W-X) model has been done to get the local resistance used to predict failure by the Volumetric Method (VM). An example is given for the case of an embedded pipe submitted to service pressure and lateral seismic displacement. The effect of this displacement is then assimilated to the shearing of the straight section of the pipe. The pipe shows a corrosion defect considered a semi-elliptical crack. The influence of hydrogen embrittlement on local strain resistance and safety factors is discussed.

The Macroscopic Mechanical Equilibrium Condition can be shown to be the physical origin of the Equation of State of any material system, then can describe all thermodynamic quasi-equilibrium processes caused by the change of the external temperature and/or mechanical environment. If it cannot be satisfied, the system would be broken.

In this paper, an improved system to efficiently utilize the low-temperature waste heat (WHUS) from the flue gas of coal-fired power plants is proposed based on heat cascade. The essence of the proposed system is that the waste heat of exhausted flue gas is not only used to preheat air for assisting coal combustion as usual but also to heat up feedwater and the low-pressure steam extraction. Preheated by both the exhaust flue gas in the boiler island and the low-pressure steam extraction in the turbine island, thereby part of the flue gas heat in the air preheater can be saved and introduced to heat the feedwater and the high-temperature condensed water. Consequently, part of the high-pressure steam is saved for further expansion in the steam turbine, which obtains additional net power output. Based on the design data of a typical 1000 MW ultra-supercritical coal-fired power plant in China, in-depth analysis of the energy-saving characteristics of the optimized WHUS and the conventional WHUS is conducted. When the optimized WHUS is adopted in a typical 1000 MW unit, net power output increases by 19.51 MW, exergy efficiency improves to 45.46%, and net annual revenue reaches 4.741 million USD. In terms of the conventional WHUS, these aforementioned performance parameters are only 5.83 MW, 44.80% and 1.244 million USD, respectively. The research of this paper can provide a feasible energy-saving option for coal-fired power plants.

The lack of defect image data is one of the main factors affecting the accuracy of supervised deep learning-based defect detection models. In response to the insufficient training data of defect images with complex backgrounds such as rust and surface oil leakage in substation equipment, leading to poor performance of the detection model, this paper proposed a novel adversarial deep learning model for substation defect generation: ADD-GAN. In comparison to existing generative adversarial networks, this model generates defect images based on effectively segmented local areas of substation equipment images, avoiding image distortion caused by global style changes. Additionally, the model utilizes a joint discriminator for overall image and defect image to address the issue of low attention to local defect areas, thereby improving the loss of image features. This enhances the overall quality of generated images as well as locally generated defect images, ultimately improving image realism. Experimental results demonstrate that the YOLOV7 object detection model trained on the dataset generated using the ADD-GAN method achieves an mAP of 81.5% on the test dataset, representing an improvement of 9.6% over the original dataset, 5.7% over traditional augmentation methods, and 7% over typical adversarial deep learning methods. This confirms that the ADD-GAN method can generate a high-fidelity dataset of substation equipment defects.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

For crystal periodic structure prediction, a new and concise approach based on the principles of statistical physics was employed to derive a new form of the equation to determine their period vectors (cell edge vectors), under general external stress. Then the new form is applicable to both classical physics and quantum physics. It also turned out to be the equation of state and the mechanical equilibrium condition for crystals under external stress and temperature. It should be helpful in piezoelectric and piezomagnetic studies, as the period vectors were changed by the external stress. For linear elastic crystals, it is actually also the microscopic but temperature-dependent form of the generalized Hooke's law, then can be used to calculate the corresponding elastic constants of the law, for given temperatures.

This paper uses event study analysis to estimate the impact of the Fed’s Quantitative Easing (QE) announcements on the mortgage market during zero lower bound period. A total of 35 QE announcements are identified and their effects are evaluated. The best-fitting IGARCH model with skewed t distribution is used to measure the QE announcement effects on daily changes of the 30-year mortgage rate, the 30-year Treasury rate and the spread between them. Announcements suggesting the start of a new round of QE reduced the mortgage rate tremendously, while the effects of further news diminished. Announcements of an increase in mortgage-backed security purchases decreased the mortgage rate more than the Treasury rate and reduced the credit risk of holding mortgage securities over Treasury securities. The long run effects of QE announcements on the mortgage rate were less than short run effects but persistent. We also find that the previous literature overestimate QE effects on interest rates in general.

Since crystals are made of periodic structures in space, predicting their three period vectors starting from any values based on the inside interactions is a basic theoretical physics problem. For the general situation where crystals are under constant external stress, we derived dynamical equations of the period vectors in the framework of Newtonian dynamics, for pair potentials recently (doi:/10.1139/cjp-2014-0518). The derived dynamical equations show that the period vectors are driven by the imbalance between the internal and external stresses. This presents a physical process where when the external stress changes, the crystal structure changes accordingly, since the original internal stress can not balance the external stress. The internal stress has both a full kinetic energy term and a full interaction term. It is extended to many-body interactions in this paper. As a result, all conclusions in the pair-potential case also apply for many-body potentials.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

This paper presents a study to accurately evaluate defects in reinforced concrete decks using ultrasonic pulse-echo signals. Two validation specimens were designed and tested where reinforced concrete deck slab specimens included planned voids and defects. A commercial Ultrasonic Pulse-Echo (UPE) device obtains 2-D images of the void/defect locations of the reinforced concrete deck. The UPE is based on the ultrasonic shear-wave test method using dry-point-contact transmitting and receiving transducers and employing a synthetic aperture focusing technique. The authors analyzed the recorded UPE A-scan data to enhance the accuracy of estimating the defects' locations using the synthetic aperture focusing technique imaging method. The analysis benefitted from an advanced denoising approach and defect echo peak extraction based on empirical modal decomposition, Hurst exponent characterization, and Hilbert envelope estimation. While output from conventional UPC devices can only provide qualitative results, the new method provides quantitative information on the anomalies inside the reinforced concrete deck. The developed approach accurately assists with assessing the location and depth of the voids/defects in the reinforced concrete deck slabs.

We have presented a controllable and human-readable polynomial neural network (CR-PNN) that is the first human-readable neural network. One can imagine its influence on system identification. Subsequently, we developed a relation spectrum in a medical application, which is likely to stand alongside the Fourier spectrum. However, the system analysis methodology is incomplete in contrast to signal processing methodology. Here, we presented the system filters for the first time. In this paper, we used the simulation system to verify the availability of the system analysis methodology. The system analysis methodology showed great properties in system identification and filter. The contribution of this paper is the system analysis methodology: transform method (CR-PNN), relation spectrum, and system filter design.

Antimicrobial and anti-viral materials have attracted significant interest in recent years due to increasing occurrences of nosocomial infections and pathogenic microbial contamination. One method to address this is the combination of photoactive compounds that can produce reactive oxygen species (ROS), such as hydrogen peroxide and hydroxyl radicals to disinfect microbes, with carrier materials that meet the application requirements. Using anthraquinone (AQ) and cellulose nanocrystals (CNCs) as the photoactive and carrier components respectively, this work demonstrates the first covalent incorporation of AQ onto CNCs. The morphology and the photoactive properties were investigated, revealing the structural integrity of the CNCs, and high degree of photoactivity of AQ-CNC materials upon UVA exposure. The AQ-CNCs also exhibited an unexpected persistent generation of ROS under darkness, which adds advantages for antimicrobial applications.

Ningxiang pig is renowned breed for its exceptional meat quality, but it possesses suboptimal carcass traits. To elucidate the genetic architecture of meat quality and carcass traits in Ningxiang pigs, we assessed heritability and executed a genome-wide association study (GWAS) concerning carcass length, backfat thickness, meat color parameters (L.LD, a.LD, b.LD), and pH at two postmortem intervals (45 minutes and 24 hours) within a Ningxiang pig population. Heritability estimates ranged from moderate to high (0.30 ~ 0.80) for carcass traits and from low to high (0.11 ~ 0.48) for meat quality traits. We identified 21 significant SNPs, the majority of which were situated within previously documented QTL regions. Furthermore, the HMGA1 gene emerged as a pleiotropic gene correlated with carcass length and backfat thickness. The ADGRF1, FKBP5, and PRIM2 genes were associated with carcass length, while the NIPBL gene was linked to backfat thickness. These genes hold potential for use in selective breeding programs targeting carcass traits in Ningxiang pigs.

In this work, we study the dynamical behaviors of the electromagnetic fields and material responses in the hyperbolic metamaterial consisting of periodically arranged metallic and dielectric layers. The thickness of each unit cell is assumed to be much smaller than the wavelength of the electromagnetic waves, so the effective medium concept can be applied. When electromagnetic (EM) fields are present, the responses of the medium in the directions parallel to and perpendicular to the layers are like that of Drude and Lorentz media, respectively. We derive the energy density of the EM fields and the power loss in the effective medium based on Poynting theorem and the dynamical equations of the polarization field. We also show that the Lagrangian density of the system can be constructed. The Euler-Lagrangian equations yield the correct dynamical equations of the electromagnetic fields and the polarization field in the medium. The canonical momentum conjugates to every dynamical field can be derived from the Lagrangian density via differentiation or variation with respect to that field. We apply Legendre transformation to this system, and find that the resultant Hamitonian density is identical to the energy density, up to an irrelevant divergence term.

In recent years, artificial neural networks (ANNs) have won numerous contests in pattern recognition, machine learning, and artificial intelligence. The basic unit of an ANN is to mimic neurons in the brain. Neuron in ANNs is expressed as f (wx+b) or f (wx). This structure does not consider the information processing capabilities of dendrites. However, recently, studies shown that dendrites participate in pre-calculation in the brain. Concretely, biological dendrites play a role in the pre-processing to the interaction information of input data. Therefore, it is time to perfect the neuron of the neural network. This paper, add dendrite processing section, presents a novel artificial neuron, according to our previous studies (CR-PNN or Gang transform). The dendrite processing section can be expressed as . Because I perfected the basic unit of ANNs— neuron, there are so many networks to try. This article gives the basic architecture for reference in future research.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

Adipose tissue composition contributes greatly to the quality and nutritional value of meat. Transcriptomic and lipidomic techniques were used to investigate the molecular mechanism of fat deposition difference among Ningxiang, Berkshire and F1 pigs. Transcriptomic analysis identified 680, 592 and 380 differentially expressed genes (DEGs) by comparing the groups of Ningxiang pigs vs Berkshire pigs, Berkshire pigs vs F1 pigs, Ningxiang pigs vs F1 pigs. Lipidomic analysis screened 423, 252, and 50 significantly changed lipids (SCLs) by comparing the groups of Ningxiang pigs vs Berkshire pigs, Berkshire pigs vs F1 pigs, Ningxiang pigs vs F1 pigs. Lycine, serine and threonine metabolism pathway, fatty acid biosynthesis and metabolism related pathways were siginificant enriched in the groups of Berkshire pigs vs Ningxiang pigs and Berkshire pigs vs F1 pigs. The DEGs (PHGDH, LOC110256000) and the SCLs (Phosphatidylserines) may have a great impact on lycine, serine and threonine metabolism pathway. Moreover, the DEGs (FASN, ACACA, CBR4, SCD, ELOV6, HACD, CYP3A46, CYP2B22, GPX1, GPX3) and the SCLs (palmitoleic acid, linoleic acid, arachidonic acid, icosadienoic acid) play important role in fatty acid biosynthesis and metabolism. Thus, the fat deposition difference among Ningxiang, Berkshire and F1 pigs may be caused by the difference of the expression pattern of key genes in multiple enrichment KEGG pathways. The research presented multiple lipids that were potentially available biological indicator and screened key genes that were potentially gene targets for molecular design breeding. The research also explored the molecular mechanisms of fat deposition difference among Ningxiang, Berkshire and F1 pigs and provides insight into the selection of backfat thickness and fat composition of adipose tissue for future breeding strategies.

Orbit and clock products are used in real-time GNSS precise point positioning without knowing their quality. This study develops a new approach to detect orbit and clock errors through comparing geometry-free and geometry-based wide-lane ambiguities in PPP model. The reparameterization and estimation procedures of the geometry-free and geometry-based ambiguities are described in detail. The effects of orbit and clock errors on ambiguities are given in analytical expressions. The numerical similarity and differences of geometry-free and geometry-based wide-lane ambiguities are analyzed using different orbit and clock products. Furthermore, two types of typical errors in orbit and clock are simulated and their effects on wide-lane ambiguities are numerically produced and analyzed. The contribution discloses that the geometry-free and geometry-based wide-lane ambiguities are equivalent in terms of their formal errors. Although they are very close in terms of their estimates when the used orbit and clock for geometry-based ambiguities are precise enough, they are not the same, in particular, in the case that the used orbit and clock, as a combination, contain significant errors. It is discovered that the discrepancies of geometry-free and geometry-based wide-lane ambiguities are coincided with the actual time-variant errors in the used orbit and clock at the line-of-sight direction. This provides a quality index for real-time users to detect the errors in real-time orbit and clock products, which potentially improves the accuracy of positioning.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

The detection accuracy of bridge superficial defect using the deep neural network approach decreases significantly under light variation and weak texture condition. To address these issues, an enhanced intelligent detection method based on the YOLOv8 deep neural network is proposed in this study. Firstly, multi-branch coordinate attention (MBCA) is proposed to improve the accuracy of coordinate positioning by introducing a global perception module in coordinate attention mechanism. Furthermore, a deformable convolution based on MBCA is developed to improve the adaptability for complex feature shapes. Lastly, the deformable convolutional network-attention-YOLO (DAC-YOLO) detection algorithm is formed by replacing the deep C2F structure in the YOLOv8 architecture with deformable convolution. A supervised dataset consisting of 4794 bridge surface damage images is employed to verify the proposed method, and results show that it achieves improvements of 2.0% and 3.4% in mAP and R. Meanwhile, the model complexity decreases by 1.2G, increasing the detection speed by 3.5/f·s-1.

Recent years have witnessed a rapid growth of code-reuse attacks in advance persistent threats and cyberspace crimes. Carefully crafted code-reuse exploits circumvent modern protection mechanisms and hijack the execution flow of a program to perform expected functionalities by chaining together existing codes. The sophistication and intrication of code-reuse exploits hinder the scrutinization and dissection on them. Although the previous literature has introduced some feasible approaches, effectiveness and reliability in practical applications remain severe challenges. To address this issue, we propose Horus, a data-driven framework for effective and reliable detection on code-reuse exploits. In order to raise the effectiveness against underlying noises, we comprehensively leverage the strengths of time-series and frequency-domain analysis, and propose a learning-based detector that synthesizes the contemporary twofold features. Then we employ a lightweight interpreter to speculatively and tentatively translate the suspicious bytes to open the black box and enhance the reliability and interpretability. Additionally, a functionality-preserving data augmentation is adopted to increase the diversity of limited training data and raise the generality for real-world deployment. Comparative experiments and ablation studies are conducted on a dataset composed of real-world instances to verify and prove the prevalence of Horus. The experimental results illustrate that Horus outperform existing methods on the identification of code-reuse exploits from data stream with an acceptable overhead. Horus does not rely on any dynamic executions and can be easily integrated into existing defense systems. Moreover, Horus is able to provide tentative interpretations about attack semantics irrespective of target program, which further improve system's effectiveness and reliability.

In the paper, a fully discrete compact difference scheme with $O(\tau^{2}+h^{4})$ precision is established by considering the numerical approximation of the one-dimensional Allen-Cahn equation. The numerical solutions satisfy discrete maximum principle under reasonable step ratio and time step constraint is proved. And the energy stability for the fully discrete scheme is investigated. An example is finally presented to show the effectiveness of scheme.

The semantic segmentation of high-resolution remote sensing images (HR-RSI) is crucial for a wide range of applications, such as precision agriculture, urban planning, natural resource assessment, and ecological monitoring. However, accurately classifying pixels in HR-RSI faces challenges due to densely distributed small objects and scale variations. Existing techniques, including Convolutional Neural Networks (CNNs) and other methods for hierarchical feature extraction and fusion of remote sensing image, often do not achieve the desired accuracy. In this paper, we propose a novel approach called the Hierarchical Rich-scale Fusion Network (HRFNet) to address these challenges. HRFNet utilizes advanced information rating and image partition techniques to extract rich-scale features within image layers. This allows for the adaptive exploration of both local and global contextual information. Moreover, we introduce a structured intra-layer to inter-layer feature aggregation module, which enables the adaptive extraction of fine-grained details and high-level semantic information from multi-layer feature maps in a highly flexible manner. Extensive experimentation has been conducted to validate the effectiveness of our proposed method. Our results demonstrate that HRFNet outperforms existing techniques, achieving state-of-the-art (SOTA) results on benchmark datasets, specifically the ISPRS Potsdam and Vaihingen datasets.

The critical period (CP) phenomenon in language development ranks among the 125 conundrums facing scientists in the 21st century, according to Science. While the phenomenon itself has been noncontroversial in first language acquisition, it still warrants an adequate explanation. Predicated on language acquisition as a complex process, questions among the first to be raised include: How do children accomplish this remarkable feat in such a short amount of time? And how do nature and nurture come together to influence language learning? In second language acquisition, however, both the notion of CP, albeit popular, and its empirical evidence have remained contested to this date - among the questions, whether the observed evidence counts as CP-specific and/or whether or not it warrants an isomorphic attribution to maturational constraints. Entwined in this debate are two well-established facets of inter-learner differential attainment. The first is that there exists a stark difference in ultimate attainment between younger and older learners. A second facet is the vast differences in ultimate attainment among older learners. In this article, adopting a social physics approach, we mathematically establish both the relationship between nature and nurture contributions and the presence of a critical period, and, at once, tender a parsimonious and probable theory for the twin phenomena of inter-learner differential attainment.

For the task planning problem of the command and control architecture, the existing algorithms have problems such as low efficiency and poor re-planning quality under abnormal conditions. Based on the requirements of the current accusation architecture, this paper constructs a distributed command and control architecture model based on multi-agents, which makes use of the superiority of multi-agents in dealing with complex tasks. The concept of MultiAgents-HTN is proposed under the framework. The original hierarchical task network planning algorithm is optimized, the multi-agent collaboration framework is redefined, and the coordination mechanism of local conflict is designed. Taking the classical resource scheduling problem as the experimental background, the comparison between the proposed algorithm and the classical HTN algorithm is carried out. The experimental results show that the proposed algorithm has higher quality and higher efficiency than the existing algorithm, and the space anomaly is heavy during processing. The planning is more efficient, and the time is more complicated and superior in dealing with the same problem, with good convergence and adaptability. The conclusion proves that the distributed command and control architecture proposed in this paper has high practicability in related fields and can solve the problem of distributed command and control architecture in multi-agent environment.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

In this paper, we study the fractional pseudo-parabolic equations u_t + (−△)^s u + (−△)^s u_t = u log |u|. Firstly, we recall the relationship between the fractional Laplace operator (−△)^s and the fractional Sobolev space H^s and discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence of global weak solution: for the low initial energy J(u₀) < d, the solution is global in time with I(u₀) > 0 or ∥u₀∥X_0(Ω) = 0 and blows up +∞ with I(u₀) < 0; for the critical initial energy J(u₀) = d, the solution is global in time with I(u₀) ≥ 0 and blows up at +∞ with I(u₀) < 0. The decay estimate of the energy functional for the global solution is also given.

Excessive intake of fluoride, one of the trace elements to maintain health, leads to liver injury. Tetramethylpyrazine (TMP) is a kind of traditional Chinese medicine monomer with good antioxidant and hepatoprotective function. The aim of this study was to investigate the effect of TMP on liver injury induced by acute fluorosis. A total of 60 1-month-old male Institute of Cancer Research mice without carriage of pathogenic bacteria were selected. All mice were fed adaptively for one week, and then randomly divided into 5 groups: control (K) group, model (F) group, low-dose (LT) group, medium-dose (MT) group and high-dose (HT) group. The control and model group were given distilled water, while 40 mg/kg (LT), 80 mg/kg (MT) and 160 mg/kg (HT) TMP were fed by gavage for two weeks with the maximum gavage volume of mice is 0.2ml/10g/d. Except for the control group, all groups were given fluoride (35 mg/kg) by intraperitoneal injection on the last day of the experiment. The results of this study showed that compared with the model group, TMP alleviated the pathological changes of liver induced by fluoride and improved the ultrastructure of liver cells; TMP significantly decreased the levels of ALT, AST and MDA (P <0.05), and increased the levels of T-AOC, T-SOD and GSH (P <0.05). The results of mRNA detection showed that TMP significantly increased the mRNA expression levels of Nrf2, HO-1, CAT, GSH-Px and SOD in liver compared with model group (P <0.05). In conclusion, TMP can inhibit oxidative stress by activating Nrf2 pathway and alleviate liver injury induced by fluoride.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

We proposed a novel concept of flight time matrix (FTM). In this work, the proposed FTM was verified first numerically. The numerical simulation revealed perfect results which showed that FTM can be used to assist the nondestructive evaluation of ballistic armor plates using acousto-ultrasonics. Two donated commercial ballistic armor plates were sought for a case study where artificial defects were prepared. The results of FTM were reasonably well. The artificial defects were clearly identifiable in one directional location array and FTM contour graphs. More comprehensive superimpositions of flight time vs location and FTM contour plots can be advanced to a better visualization of the defect presence. The resolution of FTM method is in the range of submillimeter or less. This study demonstrated that AU (acousto-ultrasonics) technique is a field applicable and yet reliable tool for inspection of the hidden defects in body armors. A broader merit of the proposed FTM algorithm is that it may promote the development of specific tools/device for nondestructive evaluations field.

Non-destructive testing is an emerging need in manufacturing processes and in service of ballis-tic armor plates. It has been shown that acoustic emission and ultrasonics are among the most applicable techniques. However, these techniques often require relative sophisticated processing and strong tech background for the evaluators. The purpose of the present work is to develop a flight time based algorithm and to demonstrate this algorithm using commercial multilayered armor plates. We proposed a novel concept of flight time matrix (FTM). In this work, the proposed FTM was verified first numerically. The numerical simulation revealed perfect results which showed that FTM can be used to assist the nondestructive evaluation of ballistic armor plates using acous-to-ultrasonics. Two donated commercial ballistic armor plates were sought for a case study where artificial defects were prepared. The results of FTM were reasonably well. The artificial defects were clearly identifiable in one directional location array and FTM contour graphs. More com-prehensive superimpositions of flight time vs location and FTM contour plots can be advanced to a better visualization of the defect presence. The resolution of FTM method is in the range of submillimeter or less. This study demonstrated that AU (acousto-ultrasonics) technique is a field applicable and yet reliable tool for inspection of the hidden defects in body armors. A broader merit of the proposed FTM algorithm is that it may promote the development of specific tools/device for nondestructive evaluations field.

To detect aberrant human behaviors from large volume of passive data collected by smartphones in real time, we propose an online anomaly detection method using Hotelling’s T-squared test. The test statistic is a weighted average, with more weight on the between-individual component when there are little data available for the individual and more weight on the within-individual component when the data are adequate. The algorithm takes only O(1) run time in each update and the required memory usage is fixed after a pre-specified number of updates. The performance of the proposed method, in terms of accuracy, sensitivity and specificity, is consistently better than or equal to the offline method that it builds upon depending on the sample size of the individual data.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Pregnancy at advanced maternal age is considered a risk factor for adverse maternal, fetal, and neonatal outcomes. Here we investigated whether maternal age could be associated with differences in the blood levels of newborn screening (NBS) markers for inborn metabolic disorders on the Recommended Universal Screening Panel (RUSP). Population-level NBS data from screen-negative singleton infants were examined, which included blood metabolic markers and covariates such as gestational age, birth weight, age at blood collection, infant sex, parent-reported ethnicity, and maternal age at delivery. Marker levels were compared between maternal age groups (age range: 15-44 years) using effect size analyses, which controlled for group size differences and potential confounding from other covariates. Our results showed that 13% of the markers had maternal age-related differences including newborn metabolites with either increased (C14, C16, C18, C18:1, C3DC) or decreased (C5OH) levels at advanced maternal age group (≥35 years, absolute Cohen’s d ≥ 0.2). The increased C3DC levels in this group correlated with a higher false-positive rate in newborn screening for malonic acidemia (p-value < 0.001), while no significant difference in screening performance was seen for other markers. Maternal age at delivery is associated with inborn metabolic differences and should be considered together with other clinical variables in genetic disease screening.

Few-shot object detection (FSOD) aims to address the challenge of requiring a substantial amount of annotations for training in conventional object detection, which is very labor-intensive. However, existing few-shot methods achieve high precision with the sacrifice of time-consuming for exhaustive fine-tuning, or take poor performance in novel-class adaptation. We presume the major reason is that the valuable correlation feature among different categories is insufficiently exploited, hindering the generalization of knowledge from base to novel categories for object detection. In this paper, we propose Few-Shot object detection via Correlation-RPN and Transformer Encoder-Decoder (CRTED), a novel training network to learn object-relevant features of inter-class correlation and intra-class compactness while suppressing object-agnostic features in the background with limited annotated samples. And we also introduce a 4-way tuple-contrast training strategy to positively activate the training progress of our object detector. Experiments over two few-shot benchmarks (Pascal VOC, MS-COCO) demonstrate that, our proposed CRTED without further fine-tuning can achieve comparable performance with current state-of-the-art fine-tuned works. The codes and pre-trained models will be released.

For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear based on permutation entropy of Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN) Adaptive Neuro-fuzzy Inference System (ANFIS) in this paper. The original signal is decomposed into 6 intrinsic mode functions (IMF) and residual components by CEEMDAN. Since the IMF contains the main characteristic information of planetary gear faults, time complexity of IMFs are reflected by permutation entropies to quantify the fault features. The permutation entropies of each IMF component are defined as the input of ANFIS, and its parameters and membership functions are adaptively adjusted according to training samples. Finally, the fuzzy inference rules are determined, and the optimal ANFIS is obtained. The overall recognition rate of the test sample used for ANFIS is 90.75%, and the recognition rate of gear with one missing tooth is relatively high. The recognition rates of different fault gears based on the method can also achieve better results. Therefore, the proposed method can be applied to planetary gear fault diagnosis effectively.

During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

Auto checkout has received more and more attention in recent years and this system automatically generates a shopping bill by identifying the picture of the products purchased by the customers. However, the system is challenged by the domain adaptation problem, where each image of the training set contains only one commodity, whereas the test set is a collection of multiple commodities. The existing solution to this problem is to resynthesize the training images to enhance the training set. Then the composite images are rendered using CycleGAN to make the image distribution of the training set and the test set more similar. However, we find that the detection boxes given by the ground truth of the common dataset contain a large part of the background area, the area will affect the training process as noise. To solve this problem, we propose a mask data priming method. Specifically, we redo the large scale Retail Product Checkout (RPC) dataset and add segmentation annotation information to each item in the training set image based on the original dataset using pixel-level annotation. Secondly, a new network structure is proposed in which we train the network using joint learning of detectors and counters, and fine-tune the detection network by filtering out suitable images from the test set. Experiments on the RPC dataset have shown that our method yields better results. we used an approach that reached 81.87% compared to 56.68% for the baseline approach which demonstrates that pixel-level information helps to improve the detection results of the network.

Critically ill patients with COVID-19 may develop serious respiratory difficulties, causing a significant reduction in blood oxygen saturation pressure. Physical Ventilation of the lungs is one of the main methods to help critically ill patients through the acute phase of infection. During extreme situations when dysfunctional lungs are filled with sticky sputum in the alveolus or when there are simply not enough ventilators to match the need, the mortality rate can be dramatically increased. Here, we propose an intravenous injection method that may increase and maintain the blood oxygen pressure at normal levels. The intravenous (IV) infusion contains oxygen nanobubbles in physiological saline solution (ONPS), in which the dissolved oxygen content can be 2-6 times higher than the normal oxygen solubility in pure water. This makes it possible to oxygenate blood with a small limited volume of IV fluid without the risk of gaseous bubble formation in blood vessels.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

Carbon dots are carbon based nanoparticles, which have the characteristics of simple preparation process, photoluminescence, biocompatibility, adjustable surface function, water solubility, and low toxicity. They are widely used in biological applications such as imaging, biosensing, photocatalysis, and molecular transfer. It has also aroused great interest among researchers in agriculture and has made significant progress in improving crop growth and production. This review presents the physiological functions of carbon dots for crop growth and development, photosynthesis, water and nutrient absorption, and abiotic stress resistance and their applications in improving ecological environment and agriculture as biosensors, and the future application prospects and research directions of carbon dots in agriculture were prospected.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

To explore the relevant factors that affect the efficacy of consciousness-regaining therapy (CRT)for prolonged disorder of consciousness(pDOC),a retrospective analysis was conducted on the case data of 114 patients with pDOC admitted to department of functional neurosurgery of Tianjin Huanhu Hospital from January 2019 to January 2022. Basic information on the cases,data on pDOC disease assessment, consciousness-regaining therapy methods, and efficacy evaluation were collected. A total of 114 patients were grouped and compared based on the efficacy at the end of treatment. Among them, there were 61 cases in the ineffective group and 53 cases in the effective group. There was no statistically significant difference (P&gt;0.05) between the two groups in terms of gender, age, etiology, acute cerebral herniation, emergency craniotomy surgery, emergency decompressive craniectomy, time from onset to start of consciousness-regaining therapy , and duration of consciousness-regaining therapy(P&gt;0.05). However, there were statistically significant differences (P&lt;0.05) in terms of secondary hydrocephalus, , consciousness-regaining therapy methods, CRS-R grading before treatment, and GOSE score at 6 months after treatment. Binary logistic regression analysis showed that the type of therapy (OR=0.169, 95% CI: 0.057-0.508) was a related factor affecting the efficacy of consciousness-regaining therapy (P&lt;0.05).Compared with non-invasive therapy, personalized awakening therapy using various invasive consciousness-regaining therapy methods can help improve the efficacy of therapy for pDOC.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

In recent years, the emergence of spatiotemporal big data has made the transition of functional identification from the physical dimension to socioeconomic or human activities becoming more common. In the identification of urban functional areas, most studies considered only a single data source and a single division scale, the research results have problems such as low update frequency or incomplete information in a single data set, and overfitting or underfitting in a single spatial resolution. Using taxi trajectory data and point of interest (POI) data as the main data source, this study proposes a multi-scale recursive identification method for urban functional areas based on cross-validation. First, used the dynamic time warping (DTW) algorithm generates a time series similarity matrix, the CA-RFM model combines the clustering algorithm and random forest model is constructed, the model uses a clustering algorithm (K-MEDOIDS) to extract sig-nificant feature regions as input, which are imported into the random forest model for UFZ identification. Then, to overcome the shortcomings of single scale in expressing urban structural characteristics, a recursive model of different levels of urban road networks is established to classify multi-scale functional areas. Finally, cross-validation using the CA-RFM model and POI quantitative identification method, obtains the final identification results of urban functional areas. This paper selects Shenzhen as the study area for the case study, the results show that the com-bination of clustering algorithm and random forest model greatly reduces the error of manual selection of training samples. In addition, the research shows the superiority of the multi-scale recursive identification method that fuses multi-source data and performs cross-validation from two aspects, that is, the division speed of urban functional area identification results is accelerated and the accuracy is improved.

Extreme-mass-ratio inspirals (EMRIs) are significant observational targets for spaceborne gravitational wave detectors, namely, LISA, Taiji, and Tianqin, which involve the inspiral of stellar-mass compact objects into massive black holes with a mass range of approximately 104∼107M⊙. EMRIs are estimated to produce long lived gravitational wave signals with more than 105 cycles before plunge, making them an ideal laboratory for exploring the strong-gravity properties of the spacetimes around the MBHs, stellar dynamics in galactic nuclei, and properties of the MBHs itself. However, the complexity of the waveform model, which involves the superposition of multiple harmonics, as well as the high-dimensional and large-volume parameter space, make the fully coherent search challenging. In our previous work, we proposed a 10-dimensional search using Particle Swarm Optimization (PSO) with local maximization over the three initial angles. In this study, we extend the search to an 8-dimensional PSO with local maximization over both the three initial angles and the angles of spin direction of the MBH where the latter contribute a time independent amplitude to the waveforms. Additionally we propose a 7-dimensional PSO search by using a fiducial value for the initial orbital frequency and shifting the corresponding 8-dimensional Time Delay Interferometry responses until a certain lag returns the corresponding 8-dimensional log-likelihood ratio maximum. The reduced dimensionality likelihoods enable us to successfully search for EMRI signals with duration of 0.5 years and signal-to-noise ratio of 50 within a wider search range than our previous study. We discuss further developments, such as using a hierarchical search to narrow down the search ranges of certain parameters, and applying Graphics Processing Units to speed up the code. These advances aim to improve the efficiency and accuracy of the EMRI search algorithm.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Diffuse cavernous hemangioma of the rectum (DCHR) is a rare benign lesion of vascular malformation. According to previous studies, the most reported major symptoms of DCHR are recurrent painless rectal bleeding or iron deficiency anemia[1][2][3][4][5][6]. We present a case of an 8Y11M boy who was diagnosed with DCHR by MRI. The patient underwent Laparoscopic-assisted transanal distal sigmoidectomy and sigmoido-anal anastomosis（Laparoscopic Swenson Procedure）, and recovered well. After the operation, the child had short-term fecal incontinence and loose stools, which returned to normal after half a year. Regardless of age and symptoms, early and correct diagnosis and treatment of DCHR and postoperative restoration of normal anal function are necessary. Laparoscopic Swenson procedure may be a good option for the treatment of DCHR.

In the environments of all kinds open coal storage sites , mining-affected coalbeds, and goafs, parts of coal body at low moisture content (≤8%) are prone to spontaneous combustion under the influence of some external environmental factors. In order to examine the influence effect of low moisture content on the spontaneous combustion tendency of coals with different metamorphic grade, we conducted temperature programmed oxidation (TPO) experiment and differential scanning calorimetry (DSC) experiment to study the spontaneous combustion characteristics of coals with different metamorphic grade at four different low moisture content, and comparatively analyzed the change laws of the characteristic parameters of four different metamorphic grade coals at four different low moisture content. The experimental results indicate that: 1) Compared other low moisture content, anthracite and fat coal at low moisture content of 1.2% show stronger tendency to undergo spontaneous combustion, long flame coal and lignite at low moisture content of 3.4% and 5.6% are more prone to spontaneous combustion. 2) Four different metamorphic grade coals at low moisture content of 7.8% are less prone to spontaneous combustion; 3) Coals with different metamorphic grade have different tendency to undergo spontaneous combustion.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

Although several carbon sequestration methods have been proposed according to theories from various disciplines, it is not known which method is the best. This study evaluated and summarized the advantage and disadvantages of several major carbon sequestration methods, including carbon capture and sequestration, ocean alkalinization, algal cultivation, and wood burial, based on the first principles, namely, sequestration scale and time, elemental stoichiometry, and energy use efficiency. This study suggested that, at present, wood burial may be a leading candidate for carbon sequestration because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture. This study also discussed the implementation of wood burial from the perspective of nutrient requirements. To achieve carbon neutrality by 2050, the present study proposed a 25-year project starting in 2025 with an average sequestration rate of 3 Pg C per year, which includes burying 1.5 Pg of dead wood carbon and the creation of 9.7 × 10⁶ ha woodland.

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

The vibration signal of the engine contains strong background noise and many kinds of modulating components, which is difficult to diagnose. Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). VMD can effectively avoid endpoint effect and modal aliasing. However, VMD cannot effectively eliminate the random noise in the signal, so the random decrement technique is introduced to solve the problem. Based on the crankshaft bearing fault simulation experiment, the four kinds of wear state vibration signals are decomposed by VMD, and the modal components with smaller permutation entropy are selected as fault components. Then the fault component is processed by the random decrement technique, and the Hilbert envelope spectrum of the fault component is obtained. Compared with the fault feature extraction method based on EMD and EEMD, the feature extraction results of the proposed method are better than those of the above two methods. The simulation analysis and the simulation test of the crankshaft bearing fault verify the effectiveness of the proposed method.

The massive use of electronic equipment has raised concerns about electromagnetic (EM) pollution, leading to increased attention to EM shielding in both civil and military applications. EM absorption materials play a crucial role in reducing the energy of microwaves projected onto their surface. In this work, we propose a novel OTA (over-the-air) antenna test method to evaluate and analyze the functionality of EM absorption materials. This method offers a new and practical way to assess the effectiveness of these materials. Measured results indicate that the presence of the EM absorption material led to a decrease in antenna gain of approximately 2-3 dB, a reduction in efficiency of more than 10-15%, and a smaller radiation pattern during the actual testing process. These findings highlight the impact of EM absorption materials on antenna performance. Compared to the traditional S-parameter testing method, the gain comparison testing method exhibits the advantages of higher accuracy and simpler operation in the lower frequency experiment.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Post-training quantization is pivotal in deploying convolutional neural networks for mobile applications. Block-wise reconstruction with adaptive rounding, as employed in prior works like BrecQ and Qdrop, facilitates acceptable 4-bit quantization accuracy. However, adaptive rounding is time-intensive, and its constraint on weight optimization space curtails the potential for quantization performance. The optimality of block-wise reconstruction hinges on the quantization status of subsequent network blocks. In this investigation, we delve into the theoretical underpinnings of the limitations inherent in adaptive rounding and block-wise reconstruction. Our exploration leads to the development of a post-training quantization methodology, designated as AE-Qdrop. This algorithm operates in two distinct phases: block-wise reconstruction and global fine-tuning. The block-wise reconstruction phase introduces a progressive optimization strategy, superseding adaptive rounding, which not only augments quantization precision but also significantly improves quantization efficiency. To mitigate the risk of overfitting, we introduce a random weighted quantized activation mechanism. During the global fine-tuning phase, we account for interdependencies among quantized network blocks. The weight of each network block will be corrected with logit matching and feature matching. Extensive experiments validate that AE-Qdrop achieves high-precision and efficient quantization. For instance, in the case of 2-bit MobileNetV2, AE-Qdrop outperforms Qdrop by achieving a 6.26% enhancement in quantization accuracy and quintupling the quantization efficiency.

In this paper, PEN3 electronic nose was used to detect and recognize fresh and moldy apples (inoculated with Penicillium expansum and Aspergillusniger) taken Golden Delicious apples as model subject. Firstly, the apples were divided into two groups: apples only inoculated with different molds (Group A) and mixed apples of inoculated apples with fresh apples (Group B). Then the characteristic gas sensors of the PEN3 electronic nose that were most closely correlated with the flavor information of the moldy apples were optimized and determined, which can simplify the analysis process and improve the accuracy of results. Four pattern recognition methods, including linear discriminant analysis (LDA), backpropagation neural network (BPNN), support vector machines (SVM) and radial basis function neural network (RBFNN), were then applied to analyze the data obtained from the characteristic sensors, respectively, aiming at establishing the prediction model of flavor information and fresh/moldy apples. The results showed that only the gas sensors of W1S, W2S, W5S, W1W and W2W in the PEN3 electronic nose exhibited strong signal response to the flavor information, indicating were most closely correlated with the characteristic flavor of apples and thus the data obtained from these characteristic sensors was used for modeling. The results of the four pattern recognition methods showed that BPNN presented the best prediction performance for the training and validation sets for both the Group A and Group B, with prediction accuracies of 96.29% and 90.00% (Group A), 77.70% and 72.00% (Group B), respectively. Therefore, it first demonstrated that PEN3 electronic nose can not only effectively detect and recognize the fresh and moldy apples, but also can distinguish apples inoculated with different molds.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Primary urethral malignancies are rare in clinical practice and elderly female are prone to suffer. The cause of PUC is unknown and may be related to long-term chronic inflammation, infection, sexual intercourse, pregnancy and irritation of the urethra. Incipient symptom of PUC is not distinctness and can easily lead to misdiagnosis. The final diagnosis relied on transvaginal ultrasound-guided mass biopsy and urethral biopsy. Early tumor treatment is mainly based on surgical resection. For advanced tumors, it is recommended to adopt a comprehensive treatment plan combining surgery, radiotherapy and chemotherapy We report this case with the aim of bringing attention to that primary urethral cancer progresses rapidly and has a poor prognosis, it is urged to call for a need of diagnostic and treatment specification.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

The Omicron EG.5 lineage of SARS-CoV-2 is currently on a trajectory to become a dominant strain. This phase 2 study aims to evaluate the immunogenicity of SCTV01E-2, a tetravalent protein vaccine, with a specific emphasis on its effectiveness against Omicron EG.5, comparing it with its progenitor vaccine, SCTV01E (NCT05933512). As of September 12, 2023, 429 participants aged ≥18 years were randomized to SCTV01E (N=215) or SCTV01E-2 (N=214) groups. Both vaccines showed increases in neutralizing antibody (nAb) against Omicron EG.5, with a 5.7-fold increase and a 9.0-fold increase in SCTV01E and SCTV01E-2 groups 14 days post-vaccination, respectively. The predetermined statistical endpoints were achieved, showing that the geometric mean titer (GMT) of nAb and the seroresponse rate (SRR) against Omicron EG.5 were significantly higher in the SCTV01E-2 group compared to SCTV01E. Additionally, SCTV01E and SCTV01E-2 induced a 5.5-fold and a 5.9-fold increase of nAb against XBB.1, respectively. Reactogenicity was generally mild and transient. No vaccine related SAEs, AESIs or deaths were reported. In summary, SCTV01E-2 elicited robust neutralizing responses against Omicron EG.5 and XBB.1 without safety concerns, underlining its potential as a versatile COVID-19 vaccine against SARS-CoV-2 variants.

This paper aims at tackling with the task of fusion feature from images and its corresponding point clouds for 3D object detection in autonomous driving scenarios basing on AVOD, an Aggregate View Object Detection network. The proposed fusion algorithms fuse features targeted from Bird’s Eye View (BEV) LIDAR point clouds and its corresponding RGB images. Differs in existing fusion methods, which are simply the adoptions of concatenation module, element-wise sum module or element-wise mean module, our proposed fusion algorithms enhance the interaction between BEV feature maps and its corresponding images feature maps by designing a novel structure, where single level feature maps and another utilizes multilevel feature maps. Experiments show that our proposed fusion algorithm produces better results on 3D mAP and AHS with less speed loss comparing to existing fusion method used on the KITTI 3D object detection benchmark.

In offshore drilling, accidents such as gas invasion, overflow, and kicks are inevitable, and they can escalate into blowouts and other catastrophic events that result in casualties and substantial economic losses. Therefore, maintaining drilling safety requires accurate monitoring of gas invasion and overflow. The majority of overflow monitoring methods currently utilized at drilling sites are threshold-based. However, monitoring parameters acquired during actual drilling operations frequently contain noise signals, making it difficult for threshold-based methods to strike a balance between improving accuracy and minimizing false positives. In this paper, Pattern Recognition-based Kick Detection (PRKD) is proposed as a novel method for diagnosing overflow in offshore drilling. This method utilizes the overflow evolution process by integrating multi-phase flow calculations, data filtering theory, pattern recognition theory, the Bayesian framework, and other theoretical models. The PRKD effectively detects and monitors gas intrusion and overflow based on single parameters by analyzing the shape and wave characteristics of the curves. The case analysis demonstrates that the proposed method for monitoring drilling overflow achieves high precision while maintaining a low false positive rate. By combining advanced computational techniques with pattern recognition algorithms, the PRKD improves the accuracy and reliability of kick detection, enabling proactive responses to potential risks, protecting the environment and human lives, and optimizing drilling operations.

An energy model that correlates fan airflow, head, speed, and system power input is essential to detect device faults and optimize control strategies in fan systems. Since the application of variable frequency drives (VFDs) makes the motor efficiency data published by manufacturers inapplicable, the fan efficiency and drive (belt-motor-VFD) efficiency must be identified for each individual system to obtain accurate energy models. The objectives of this paper are to identify an energy model of existing VFD-motor-fan systems using available experimental data and demonstrate its applications in loose belt fault detection and virtual airflow meter development for optimal control. First, an approach is developed to identify the fan head, fan efficiency and drive efficiency curves using available fan head, speed, and system power input as well as temporarily measured airflow rate without measuring shaft power. Then the energy model is identified for an existing VFD-motor-fan system. Finally, the identified model is applied to detect the slipped belt faults and develop the virtual airflow meter. The experiment results reveal that the developed approach can effectively obtain the energy model of VFD-motor-fan systems and the model can be applied to effectively detect slipped belt faults and accurately calculate the fan airflow rate.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

Right ventricular remodeling and its function are closely related to the symptom severity and survival of hypoxia pulmonary hypertension, but molecular mechanisms of cardiomyocyte hypertrophy and myocardial injury remain unclear. It evaluated the cardiac function (by right cardiac catheterization to measure right ventricular systolic pressure and mean pulmonary artery pressure), myocardial tissue morphology（Haematoxylin and Eosin）, myocardial hypertrophy (Wheat Germ Agglutinin Staining), then RNA sequencing was applied to explore the mechanism, which results were verified by western blot in final. Hypoxia developed pulmonary hypertension, right ventricular diastolic and systolic functions were enhanced in rats, such as the mean pulmonary artery pressure, systolic pressure of pulmonary artery, the max pressure of right ventricular, the mean right ventricular pressure, and the heart rate was significantly higher than that in control. We found that Hif-1 signaling pathway and p38-MAPK signaling pathway have been activated by hypoxia, and cardiomyocyte apoptosis also aggravated in the right ventricular, which might be one cause of cardiomyocyte hypertrophy and myocardial injury, and targeted intervention might be one potential prevention for cardiomyocyte hypertrophy and myocardial injury induced by hypoxia.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

Considering the spectrum shortage problem of IoT devices, we introduce a collaborative spectrum sensing (CSS) framework in this paper to identify available spectrum resources, so that IoT devices can access it and meanwhile avoid causing harmful interference to the normal communication of the primary user (PU). However, in the process of the PU’s signal detection in IoT devices, the issue about the stopping time and decision cost arises. To this end, we propose a distributed cognitive IoT model, which includes two IoT devices independently using sequential decision rules to detect the PU. On this basis, we define the stopping time and cost function for IoT devices, and formulate an average cost optimization problem in CSS. To solve this problem, we further regard the optimal stopping time problem as a finite horizon problem, and solve the threshold of the optimal decision rule by dynamic programming. At last, numerical simulation results demonstrate the correctness of our proposal in terms of the global false alarm and miss detection probability, and it always achieves minimal average cost under various cost of each observation taken and thresholds.

In this paper, the distributed formation tracking control problem of quadrotor unmanned aerial vehicles (UAVs) is considered. Adaptive backstepping technology is used to design flight control schemes for quadrotor UAVs. For the position subsystem, a distributed robust formation tracking control scheme is developed to achieve formation flight of quadrotor UAVs and track the desired flight trajectory. For the attitude subsystem, an adaptive disturbance rejection control scheme is proposed to achieve attitude stabilization during UAV flight under uncertain disturbances. Compared with the existing results, the novelty of this paper is that the proposed formation control scheme does not require the use of the quadrotor model parameters. Finally, a quadrotor UAV swarm system is used to verify the effectiveness of the proposed control scheme.