Input reconstruction problem is usually encountered in the areas such as virtual sensing, image restoration, sensor linearization, and communications. The input reconstruction problem can be seen as an inverse problem. Given a nominal system, two types of approaches are commonly used for solving the inverse problem. The first one is to directly invert the nominal system, and the second one is to derive an inversion of the nominal system in an indirect way. However, for the first type of approaches, system inversion cannot be directly conducted under some conditions such as there exist nonminimum-phase zeros in the nominal system, while for the second type of approaches, simultaneously guaranteeing stability and causality of the obtained inversion is still not solved well. In order to avoid the drawbacks existing in the two types of approaches, an alternative approach is proposed for input reconstruction. In this approach, the input signal is first modeled as the output of a state-space model, afterwards two Kalman filters for the model resulted by combining the input signal model and the nominal system model are implemented alternatively such that the input signal can be sequentially reconstructed in an infinite horizon. The proposed input reconstruction approach is applied in two examples, and simulation results can illustrate the effectiveness of the proposed approach.

The inverse system identification toolbox named INVSID 1.0 for MATLAB, which is used to identify the inversion of single-input single-output systems, is developed. The complete process of developing the toolbox is demonstrated. Afterwards, a numerical example is illustrated to describe how the toolbox can be used to solve inverse identification problems. Simulation results demonstrate the effectiveness of the toolbox.

Direct and indirect effects after mine operations cease must ideally be subject to perpetual monitoring routines in order to detect possible risks or avoid adverse effects on the surrounding ecosystems at an early stage. In this contribution, mining subsidence lakes created inside the nature reserve Kirchheller Heide and Hilsfeld Forest are subjected to analysis for a long-term monitoring scheme. For this purpose, we employ high-resolution unmanned aerial system (UAS)-based multispectral and thermal mapping tools to provide a fast, non-invasive and multitemporal environmental monitoring method. Specifically, we propose to monitor vegetation evolution through multispectral analysis, biotypes identification using machine learning algorithms, and water surface extent detection, together with their thermal behavior. The aim of this contribution is to present the proposed workflow and first results to establish a baseline for future analyses and subsequent surveys for longterm multi-temporal monitoring

Finite element (FE) modeling is commonly used as a method to investigate the influence of medical devices, such as implants and screws and their effects on the biomechanical behavior of the spine. Another simulation method is a multi-body simulation (MBS), where the model is composed of several non-deformable bodies. MBS solvers generally require a very short computing time for dynamic tasks compared to an FE analysis. Considering this computational advantage, in this study, we examine whether parameters whose values are not known a priory can be determined with sufficient accuracy using MBS model. Therefore, we propose a Many-at-a-time sensitivity analysis method that allows approximating these a priory unknown parameters without requiring long simulation times. This method enables a high degree of MBS model optimization to be achieved in an iterative process. The sensitivity analysis method is applied to a simplified screw-vertebra model, consisting of an anterior anchor implant screw and vertebral body of C4. An experiment described in the literature is used as a basis for developing and assessing the potential of the method for sensitivity analysis and to validate the models action. The optimal model parameters for the MBS model were determined to be c=823224N/m for stiffness and d=488Ns/m for damping. The presented method of parameter identification can be used in studies including more complex MBS spine models or to set initial parameter values that are not available as initial values for FE models.

Different notions of entropy can be identified in different communities: (i) the thermodynamic sense, (ii) the information sense, (iii) the statistical sense, (iv) the disorder sense, and (v) the homogeneity sense. Especially the “disorder sense” and the “homogeneity sense” relate to and require the notion of space and time. One of the few prominent examples relating entropy to geometry and to space is the Bekenstein-Hawking entropy of a Black Hole. Although being developed for the description of a physics object—a black hole—having a mass, a momentum, a temperature, a charge etc. absolutely no information about these attributes of this object can eventually be found in the final formula. In contrast, the Bekenstein-Hawking entropy in its dimensionless form is a positive quantity only comprising geometric attributes like an area A—which is the area of the event horizon of the black hole-, a length L_P—which is the Planck length - and a factor ¼. A purely geometric approach towards this formula will be presented. The approach is based on a continuous 3D extension of the Heaviside function, with this extension drawing on the phase-field concept of diffuse interfaces. Entropy enters into the local, statistical description of contrast respectively gradient distributions in the transition region of the extended Heaviside function definition. The structure of the Bekenstein-Hawking formula eventually is derived for a geometric sphere based on mere geometric-statistic considerations.

SORL1 gene encodes LR11/SorLA, a protein that binds -amyloid precursor protein (bAPP) and drives its intracellular trafficking. SORL1 mutations occurring frequently in a subset of familial cases of Alzheimer’s disease (AD) have been documented but their pathogenic potential is not yet clear and questions remain concerning their putative influence on the physiopathological processing of bAPP. We have assessed the influence of three SORL1 mutations that were described as likely disease-causing and that were associated with either benign (SorLA924) or severe (SorLA141 and SorLA511) AD phenotypes. We examined the influence of wild-type and mutants SorLA in transiently transfected HEK293 cells expressing either wild-type or Swedish mutated bAPP on bAPP expression, secreted Ab and sAPPa levels, intracellular Ab40 and Ab42 peptides, APP-CTFs (C99 and C83) expressions, a-, b- and g-secretases expressions and activities as well as Ab and CTFs-degrading enzymes. These paradigms were studied in control conditions or after pharmacological proteasomal modulation. We also established stably transfected CHO cells expressing wild-type SorLA and established the colocalization of wild-type SorLA and bAPP. Overall, although we mostly confirmed previous data concerning the influence of wild-type SorLA on bAPP processing, we were unable to evidence significant alterations triggered by our set of SorLA mutants, whatever the cells or pharmacological conditions examined. Our study however does not rule out the possibility that other AD-linked SORL1 mutations could indeed affect bAPP processing and that pathogenic mutations examined in the present study could interfere with other cellular pathways/triggers in AD.

Oilseed plants of the Brassicaceae plant family are cultivated for food, feed and industrial purposes on large-scale in Europe. This review gives an overview of current market-oriented applications of new genomic techniques (NGTs) in relevant Brassicaceae oilseed crops based on a literature survey. In this respect, changes in oil quality, yield, growth and resistance to biotic and abiotic stress are goals in oilseed rape (B. napus) and camelina (C. sativa). Environmental risk assessment scenarios are developed for specific NGT applications in Brassicaceae oilseed crops with either a changed oil composition or with fitness related traits. In case of a changed oil composition an increase or decrease of polyunsaturated fatty acids (PUFA) demonstrates risks for health and survival of pollinators. In case of fitness related traits other risks were identified, i. e. an increased risk of spread and persistence of NGT plants. Furthermore, there are indications for potential disturbance of interactions with the environment, involving signalling pathways and reaction to stress conditions. It is shown that for a comprehensive risk assessment the technological potential of NGTs, the plants’ biology and the scale of releases have to be considered in combination. Therefore, the release of NGT plants into the environment for agricultural purposes will require risk assessment and monitoring of single traits as well as of combinatorial and long-term cumulative effects. In addition, risk management should develop concepts and measures to control and potentially restrict the scale of releases. This is especially relevant for NGT Brassicaceae in Europe which is a centre of diversity of this plant family.

Sustainable food consumption has attracted a widespread attention during last decades by scholars, policy makers and consumers. In line with this, farmers’ markets (FMs) have the potential to encourage sustainable agricultural production and consumption. By reducing the number of actors and distances along the food chain, these alternative food systems foster the reconnection between farmers and consumers and contribute to different social, economic and environmental sustainable goals. This paper provides insights on the role of consumers' sustainability concerns related to their motivation for shopping at FMs. By means of a choice experiment, we analyze the determinants of consumers’ WTP for buying apples at FMs. We are particularly interested in understanding how attitudes towards the three sustainability dimensions are related to consumer preferences in this context. We find that consumer attitudes towards direct contact with producers, contributing to farmers’ income, and environmental benefits can be directly related to product characteristics that are specific to FMs.

Hamiltonians describing the relativistic quantum dynamics of a particle with an arbitrary spin are shown to exhibit a supersymmetric structure when the even and odd elements of the Hamiltonian commute. For such supersymmetric Hamiltonians an exact Foldy-Wouthuysen transformation exits which brings it into a block-diagonal form separating the positive and negative energy subspaces. Here the supercharges transform between energy eigenstates of positive and negative energy. The relativistic dynamics of a charged particle in a magnetic field is considered for the case of a scalar (spin-zero) boson obeying the Klein-Gordan equation, a Dirac (spin one-half) fermion and a vector (spin-one) boson characterised by the Proca equation.

The Newton-Hooke duality and its generalization to arbitrary power laws in classical, semiclassical and quantum mechanics are discussed. We pursue a view that the power-law duality is a symmetry of the action under a set of duality operations. The power dual symmetry is defined by invariance and reciprocity of the action in the form of Hamilton’s characteristic function. We find that the power-law duality is basically a classical notion and breaks down at the level of angular quantization. We propose an ad hoc procedure to preserve the dual symmetry in quantum mechanics. The energy-coupling exchange maps required as part of the duality operations that take one system to another lead to an energy formula that relates the new energy to the old energy. The transformation property of Green function satisfying the radial Schrödinger equation yields a formula that relates the new Green function to the old one. The energy spectrum of the linear motion in a fractional power potential is semiclassically evaluated. We find a way to show the Coulomb-Hooke duality in the supersymmetric semiclassical action. We also study the confinement potential problem with the help of the dual structure of a two-term power potential.

Multi-parameter families of Lax pairs for the modified Korteweg-de Vries (mKdV) equation are defined by applying a direct method developed in the present study. The gauge transformations converting the defined Lax pairs to some simpler forms and reducing the variety of the Lax pairs this way are found. The direct method and its possible applications to other types of evolution equations are discussed.

It is well known that a sequence of two non-collinear Lorentz boosts (pure Lorentz transformations) does not correspond to a Lorentz boost, but involves a spatial rotation, the Wigner or Thomas-Wigner rotation. We visualize the interrelation between this rotation and the relativity of distant simultaneity by moving a Born-rigid object on a closed trajectory in several steps of uniform proper acceleration. Born-rigidity implies that the stern of the boosted object accelerates faster than its bow. It is shown that at least five boost steps are required to return the object's center to its starting position, if in each step the center is assumed to accelerate uniformly and for the same proper time duration. With these assumptions, the Thomas-Wigner rotation angle depends on a single parameter only. Furthermore, it is illustrated that accelerated motion implies the formation of an event horizon. The event horizons associated with the five boosts constitute a natural boundary to the rotated Born-rigid object and ensure its finite size.

Mereotopology is a concept rooted in analytical philosophy. The phase-field concept is based on mathematical physics and finds applications in materials engineering. The two concepts seem to be disjoint at a first glance. While mereotopology qualitatively describes static relations between things like x isConnected y (topology) or x isPartOf y (mereology) by first order logic and Boolean algebra, the phase-field concept describes the geometric shape of things and its dynamic evolution by drawing on a scalar field. The geometric shape of any thing is defined by its boundaries to one or more neighboring things. The notion and description of boundaries thus provides a bridge between mereotopology and the phase-field concept. The present article aims to relate phase-field expressions describing boundaries and especially triple junctions to their Boolean counterparts in mereotopology and contact algebra. An introductory overview on mereotopology is followed by an introduction to the phase-field concept already indicating first relations to mereo- topology. Mereotopological axioms and definitions are then discussed in detail from a phase-field perspective. A dedicated section introduces and discusses further notions of the isConnected relation emerging from the phase-field perspective like isSpatiallyConnected, isTemporallyConnected, isPhysicallyConnected, isPathConnected and wasConnected. Such relations introduce dynamics and thus physics into mereotopology as transitions from isDisconnected to isPartOf can be described.

Mereology stands for the philosophical concept of parthood and is based on a sound set of fundamental axioms and relations. One of these axioms relates to the existence of a universe as a thing having part all other things. The present article formulates this logical expression first as an algebraic inequality and eventually as an algebraic equation reading in words: The universe equals the sum of all things. “All things” here are quantified by a “number of things”. Eventually this algebraic equation is normalized leading to an expression The whole equals the sum of all fractions. This introduces “1” or “100%” as a quantitative – numerical - value describing the “whole”. The resulting “basic equation” can then be subjected to a number of algebraic operations. Especially squaring this equation leads to correlation terms between the things implying that the whole is more than just the sum of its parts. Multiplying the basic equation (or its square) by a scalar allows for the derivation of physics equations like the entropy equation, the ideal gas equation, an equation for the Lorentz-Factor, conservation laws for mass and energy, the energy-mass equivalence, the Boltzmann statistics, and the energy levels in a Hydrogen atom. It further allows deriving a “contrast equation” which may form the basis for the definition of a length and a time scale. Multiplying the basic equation with vectors, pseudovectors, pseudoscalars and eventually hypercomplex numbers opens up the realm of possibilities to generate many further equations.

A new mesogenic non-symmetric dimeric monomer with a terminal olefin function, forming a twist bend nematic (Ntb) as well as a nematic (N) phase was synthesized, using an enhanced synthetic methodology, which avoids isomerization of the terminal double bond in the preparation of the dimer. This monomer was attached to a pentamethyldisiloxane group, resulting in SmA LC phase behaviour of the ensuing material. Linking the monomer to a siloxane main chain resulted in nematic phase behaviour. Detailed studies with the Ntb phase forming dimer DTC5C7 show full miscibility of the dimer and the new LC polymer in the LC state, suggesting that the side-chain LC polymer forms a Ntb phase as the low temperature nematic phase. Copolymerizing the monomer with a cyanobiphenyl based monomer allows to tune the glass transition and phase behavior further.

Abstract: Experiments conducted to date to verify the relativistic gravitational time dilation have limited scientific significance because the basic postulate of Einstein’s relativistic GR that the same time (t0) is measured in all non-inertial frames of reference, because all non-inertial frames of reference must be equal, has not yet been verified by time measurements. According to Einstein's relativistic GR, a correlation between time and different gravitational potentials must be the result of a relative relation between non-inertial frames of reference and must not the result of any other physical influence. An experiment that can differentiate between a causal correlation (relative relation) and an apparent correlation (relativistic relation) between time and gravitational potentials is still outstanding. The expressions "relative" and "relativistic" are often used as synonyms. However, Einstein's GR is a relativistic theory. In the case of general relativity, relativistic means that time depends only on the relative relation between non-inertial frames of reference and not on other physical factors. The author proposes an easy-to-realize experiment that is able to distinguish between a causal correlation (relative relation) and an apparent correlation (relativistic relation) between time and gravitational potentials, which can confirm or falsify Einstein's relativistic GR. .

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

The effects of buckwheat intake on cardiovascular diseases (CVD) have not been systematically investigated. The aim of the present study was to comprehensively summarise studies in humans and animals evaluating the impact of buckwheat consumption on CVD risk markers and to conduct a meta-analysis of relevant data. Thirteen randomised, controlled human studies, two cross-sectional human studies and twenty-one animal studies were identified. Using random effects models, the weighted mean difference of post-intervention concentrations of blood glucose, total cholesterol and triglycerides were significantly decreased following buckwheat intervention compared with controls [differences in blood glucose: -0.85 mmol/L (95% CI: -1.31, -0.39), total cholesterol: 0.50 mmol/L (95% CI: -0.80, -0.20) and triglycerides: 0.25 mmol/L (95% CI: -0.49, -0.02)]. Responses of a similar magnitude were seen in two cross-sectional studies. For animal studies, nineteen of twenty-one studies showed a significant reduction in total cholesterol of between 12 and 54%, and fourteen of twenty studies showed a significant reduction in triglycerides of between 2 and 74%. All exhibited high unexplained heterogeneity. There was inconsistency in HDL cholesterol outcomes in both human and animal studies. It remains unclear whether increased buckwheat intake significantly benefits other markers of CVD risk, such as weight, blood pressure, insulin, and LDL-cholesterol, and underlying mechanisms responsible for any effects are unclear.

(1) Background: There is not much research about obesity in nursing homes although knowledge will help us to develop customized treatment plans and prevention strategies, which may help to decrease the burden for all persons involved. The objective of conducting this study was to describe the prevalence of obesity and the association between obesity and care problems in nursing home patients. (2) Methods: This study is a secondary data analysis of data collected in an annually performed cross-sectional study called “Nursing Quality Measurement 2.0”. A standardized and tested questionnaire was used to collect data. (3) Results: 1236 nursing home patients took part and 16.7% of them were obese. The multivariate logistic regression analysis results show that urinary incontinence is significantly associated with the presence of obesity (OR 2.111). The other care problems of pressure injuries, fecal and double incontinence, physical restraints, falls and pain were not associated with obesity. (4) Conclusion: The results indicate that, in the nursing home setting, health care staff should pay special attention to the patients’ nutritional and continence status and help patients maintain a normal, healthy weight. Conducting more studies with larger sample sizes is recommended, as this will allow differentiation among different obesity classes.

The sustainable management of water scarcity is a global crucial issue. Germany has es- tablished efficient water management systems, but the agricultural sector still struggles with water scarcity as the demand surpasses the available water supply. The primary aim is to establish a framework for making water accessible for irrigation and additional use on households through the effective utilization of recycled water from wastewater treatment facilities. The research inquiries are focused on evaluating the changes in the agricultural irrigation model in CROPWAT, determining the spatial distribution of zonal severity, estimating the capacity of urban roof catchments, and evaluating the reduction volume of efficient water required from the existing wastewater treatment plant supply. According to the findings, the annual amount of water required for agriculture in the designated study location is approximately 2.9 million m3. Although there is no initial need for irrigation water, yet the demand for irrigation water increases during the development, active growth, and mature stages of maize, winter wheat, and wine grapes, reaching around 189mm, 225mm, and 62mm, respectively. According to our observation, the annual water supply in Weinstadt is around 4 million m3. On the other hand, the amount of water calculated from urban roof rainfall is estimated 0.8 million m3, which is considered valuable from an economic standpoint. This economically efficient volume of water would reduce the current treated water supply passes an opportunity for enhanced agricultural irrigation

Good eyesight belongs to the most-valued attributes of health, and diseases of the eye are a significant health care burden. Case numbers are expected to further increase in the next decades due to an aging society. The development of drugs in ophthalmology, however, is difficult due to limited accessibility of the eye, in terms of drug administration and in terms of sampling of tissues for drug pharmacokinetics (PK) and pharmacodynamics (PD). Ocular quantitative systems pharmacology (QSP) models provide the opportunity to describe the distribution of drugs in the eye as well as the resulting drug-response in specific segments of the eye. In particular, ocular physiologically-based pharmacokinetic (PBPK) models are necessary to describe drug concentration levels in different regions of the eye. Further, ocular effect models employing molecular data from specific cellular systems are needed to develop dose-response correlations. We here describe the current status of PK/PBPK as well as PD models for the eye and describe cellular systems, data repositories as well as animal models in ophthalmology. The application of the various concepts is highlighted for the development of new treatments for post-operative fibrosis after glaucoma surgery.

Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick-slip transition of Coulomb’s approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why, dynamic friction models were developed in the last decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too simple approximation. The recently published second order dynamic friction model describes the dynamics of a fictitious bristle more accurately. Its performance is compared here to stick-slip friction models, developed and launched not long ago by commercial multibody software packages.

Annually, an estimated 13-26 million newborns need respiratory support and 2-3 million newborns need extensive resuscitation, defined as chest compression and 100% oxygen with or without epinephrine in the delivery room. Despite such care, there is a high incidence of mortality and short-term neurologic morbidity. The poor prognosis associated with receiving chest compression alone or with medications in the delivery room raises questions as to whether improved cardiopulmonary resuscitation methods specifically tailored to the newborn could improve outcomes. This review discusses the current recommendations, mode of action, different compression to ventilation ratio, continuous chest compression with asynchronous ventilations, chest compression and sustained inflation optimal depth, and oxygen concentration during cardiopulmonary resuscitation.

A rapid synthesis of chiral sulfoxide-functionalized meta-terphenyl derivatives by a 2,5-[C4+C2] ring transformation reaction of pyrylium salts with in-situ generated enantio-merically pure .alpha.-sulfinylacetaldehydes is described. This synthetic method demonstrates for the first time the use of .alpha.-sulfinylacetaldehydes in a reaction sequence initiated by nu-cleophilic attack of pyrylium salts by .alpha.-sulfinylcarbanions to generate chiral aromatic systems. The method presented shows broad applicability starting with various methyl sulfoxides and a number of functionalized pyrylium salts, furnishing meta-terphenyls with complex substitution patterns from readily accessible starting compounds.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Assessment of health-related quality of life (HRQoL) after pediatric traumatic brain injury (TBI) has been limited in children and adolescents due to a lack of disease-specific instruments. To fill this gap, the Quality of Life after Traumatic Brain Injury for Children and Adolescents (QOLIBRI-KID/ADO) was developed for the German-speaking population. Reference values from a comparable general population are essential for comprehending the impact of TBI on health and well-being. This study examines the validity of the German QOLIBRI-KID/ADO in a general pediatric population in Germany and provides reference values for use in clinical practice. Overall, 1997 children and adolescents aged 8-17 years from the general population and 300 from the TBI population participated in the study. The questionnaire was tested for reliability and validity. A measurement invariance (MI) approach was used to assess the comparability of the HRQoL construct between both samples. Reference values were determined by percentile-based stratification according to factors that significantly influenced HRQoL in regression analyses. The QOLIBRI-KID/ADO demonstrated strong psychometric properties. The HRQoL construct was measured largely equivalently in both samples, and reference values could be provided. The QOLIBRI-KID/ADO was considered reliable and valid for assessing HRQoL in a general German-speaking pediatric population, allowing for clinically meaningful comparisons between general and TBI populations.

LONP1 is the principal AAA+ unfoldase and bulk protease in the mitochondrial matrix, so its deletion causes embryonic lethality. The AAA+ unfoldase CLPX and the peptidase CLPP also act in the matrix, conspicuously during stress periods, but their substrates are poorly defined. Mammalian CLPP deletion triggers infertility, deafness, growth retardation, and cGAS-STING activated cytosolic innate immunity. CLPX mutations impair heme biosynthesis and heavy metal homeostasis. CLPP and CLPX are conserved from bacteria to human, despite their secondary role for proteolysis. Based on recent proteomic-metabolomic evidence from knockout mice and patient cells, we propose that CLPP acts on phase-separated ribonucleoprotein granules, and CLPX on multi-enzyme condensates, near the inner mitochondrial membrane, as first-aid system. Trimming within assemblies, CLPP rescues stalled processes in mitoribosomes, in mitochondrial RNA granules and nucleoids, and in D-foci-mediated degradation of toxic double-stranded mtRNA / mtDNA. Unfolding multi-enzyme condensates, CLPX maximizes PLP-dependent delta-transamination, and rescues malformed nascent peptides. Overall, their actions occur in granules with multivalent or hydrophobic interactions, separated from the aqueous phase. Thus, the role of CLPXP in the matrix is compartment-selective, like peptidases MPP at precursor import pores, m-AAA and i-AAA at either IMM face, PARL within the IMM, and OMA1/HTRA2 in the intermembrane space.

Terms related to gradients of scalar fields are introduced as scalar products into the formulation of entropy. A Lagrange density is then formulated by adding constraints based on known conservation laws. Applying the Lagrange formalism to the resulting Lagrange density leads to the Poisson equation of gravitation and also includes terms being related to curvature of space. The formalism further leads to terms possibly explaining nonlinear extensions known from modified Newtonian dynamics approaches. The article concludes with a short discussion of the presented methodology and provides an outlook on other phenomena, which might be tackled using this new approach.

The parameters of logistic regression models are usually obtained by the method of maximum likelihood (ML). However, in analyses of small data sets or data sets with unbalanced outcomes or exposures, ML parameter estimates may not exist. This situation has been termed “separation” as the two outcome groups are separated by the values of a covariate or a linear combination of covariates. To overcome the problem of non-existing ML parameter estimates, applying Firth’s correction (FC) was proposed. In practice, however, a principal investigator might be advised to “bring more data” in order to solve a separation issue. We illustrate the problem by means of an examples from colorectal cancer screening and ornithology. It is unclear if such an increasing sample size (ISS) strategy that keeps sampling new observations until separation is removed improves estimation compared to applying FC to the original data set. We performed an extensive simulation study where the main focus was to estimate the cost-adjusted relative efficiency of ML combined with ISS compared to FC. FC yielded reasonably small root mean squared errors and proved to be the more efficient estimator. Given our findings, we propose not to adapt the sample size when separation is encountered but to use FC as the default method of analysis whenever the number of observations or outcome events is critically low.

Snow is a vital environmental parameter and dynamically responsive to climate change, particularly in mountainous regions. Snow cover can be monitored at variable spatial scales using Earth Observation (EO) data. Long-lasting remote sensing missions enable the generation of multi-decadal time series and thus the detection of long-term trends. However, there have been few attempts to use these to model future snow cover dynamics. In this study, we therefore explore the potential of such time series to forecast the Snow Line Elevation (SLE) in the European Alps. We generate monthly SLE time series from the entire Landsat archive (1985-2021) in 43 Alpine catchments. Positive long-term SLE change rates are detected, with the highest rates (5-8 m/y) in the Western and Central Alps. We utilize this SLE dataset to implement and evaluate seven uni-variate time series modeling and forecasting approaches. The best results were achieved by Random Forests, with a Nash-Sutcliffe efficiency (NSE) of 0.79 and a Mean Absolut Error (MAE) of 258 m, Telescope (0.76, 268 m), and seasonal ARIMA (0.75, 270 m). Since the model performance varies strongly with the input data, we developed a Combined forecast based on the best performing methods in each catchment. This approach was then used to forecast the SLE for the years 2022-2029. In the majority of the catchments the shift of the forecast median SLE level retained the sign of the long-term trend. In cases where a deviating SLE dynamic is forecast a discussion based on the unique properties of the catchment and past SLE dynamics is required. In the future, we expect major improvements in our SLE forecasting efforts by including external predictor variables in a multi-variate modeling approach.

This paper deals with a generic methodology to evaluate the magnetic parameters of contactless power transfer systems. Neumann's integral has been used to create a matrix method that can model the magnetics of single coils (circle, square, rectangle). The principle of superposition has been utilised to extend the theory to multi-coil geometries such as double circular, double rectangle and double rectangle quadrature assuming linearity of magnetics. Numerical and experimental validation has been performed to validate the analytical models developed. A rigorous application of the analysis has been carried out to study misalignment and hence the efficacy of various geometries to misalignment tolerance. Comparison of single-coil and multi-coil shapes considering coupling variation with misalignment, power transferred and maximum efficiency is carried out.

Thousands of antibodies for diagnostic and other analytical purposes are on the market. However, it is often difficult to identify duplicates, reagent changes, and to assign the correct original publications to an antibody. This slows down scientific progress and might even be a cause of irreproducible research and a waste of resources. Recently, activities were started to suggest the sole use of recombinant antibodies in combination with the open communication of their sequence. In this case, such uncertainties should be eliminated. Unfortunately, this approach seems to be rather a long-term vision since the development and manufacturing of recombinant antibodies remain quite expensive in the foreseeable future. Also, nearly all commercial antibody suppliers may be reluctant to publish the sequence of their antibodies, since they fear counterfeiting. De-novo sequencing of antibodies is also not feasible today for a reagent user without access to the hybridoma clone. Nevertheless, it seems to be crucial for any scientist to have the opportunity to identify an antibody undoubtedly to guarantee the traceability of any research activity using antibodies from a third party as a tool. For this purpose, we developed a method for the identification of antibodies based on a MALDI-TOF-MS fingerprint. To circumvent lengthy denaturation, reduction, alkylation, and enzymatic digestion steps, the fragmentation was performed with a simple formic acid hydrolysis step. Eighty-nine unknown monoclonal antibodies were used for this study to examine the feasibility of this approach. Although the molecular assignment of peaks was rarely possible, antibodies could be easily recognized in a blinded test, simply from their mass-spectral fingerprint. A general protocol is given, which could be used without any optimization to generate fingerprints for a database. We want to propose that in most scientific projects relying critically on antibody reagents, such a fingerprint should be established to prove and document the identity of the used antibodies and to assign a specific reagent to a datasheet of a commercial supplier, a public database record or an antibody ID.

Glioblastoma (GBM) is the most aggressive brain cancer. To model GBM in research, orthotopic brain tumor models, including syngeneic models like GL261 and genetically engineered mouse models like TRP, are used. In longitudinal studies, tumor growth and treatment response are typ-ically tracked with in vivo imaging, including bioluminescence imaging (BLI), which is quick, cost-effective, and easily quantifiable. However, BLI requires luciferase-tagged cells, and recent studies indicate that the luciferase gene can elicit an immune response, leading to tumor rejection and experimental variation. We sought to optimize the engraftment of two luciferase-expressing GBM models, GL261 Red-FLuc and TRP-mCherry-FLuc, showing differences in tumor take, with GL261 Red-FLuc cells requiring immunocompromised mice for 100% engraftment. Immuno-histochemistry and MRI revealed distinct tumor characteristics: GL261 Red-FLuc tumors were well-demarcated with densely packed cells, high mitotic activity, and vascularization. In con-trast, TRP-mCherry-FLuc tumors were large, invasive, and necrotic, with perivascular invasion. Quantifying tumor volume using the HALO® AI analysis platform yielded results comparable to manual measurements, providing a standardized and efficient approach for reliable high-throughput analysis of luciferase-expressing tumors. Our study highlights the importance of considering tumor engraftment when using luciferase-expressing GBM models, providing in-sights for preclinical research design.

Volcanism powered by tidal forces inside celestial bodies can provide enough energy to keep important solvents for living systems in the liquid phase. Moreover, tidal forces and their environmental consequences may strongly influence habitability of planets and other celestial bodies and may result in special forms of live and living conditions. A prerequisite to calculate such tidal interactions and consequences is depending on simulations for tidal accelerations in a multi-body system. Unfortunately, from measurements in many extrasolar planetary systems only few physical and orbital parameters are well enough known for investigated celestial bodies. For calculating tidal acceleration vectors under missing most orbital parameter exactly, a simulation method is developed that is only based on a few basic parameters, easily measurable even in extrasolar planetary systems. Such a method as being presented here, allows finding a relation between the tidal acceleration vectors and potential heating inside celestial objects. Using values and results of our model approach to our solar system as a “gold standard” for feasibility allowed us to classify this heating in relation to different forms of volcanism. This “gold standard” approach gave us a classification measure for the relevance of tidal heating in other extrasolar systems with a reduced availability of exact physical parameters. We would help to estimate conditions for the identification of potential candidates for further sophisticated investigations by more complex established methods like viscoelastic multi-body theories. As a first example, we applied the procedures developed here to the extrasolar planetary system TRAPPIST-1 as an example to check our working hypothesis.

DIEP-based breast reconstruction necessitates wide undermining at the abdominal donor-site, creating large wound areas. Flap harvesting is usually conducted using electrosurgical dissection devices. This study sought to compare the clinical outcomes in patients after using the PEAK PlasmaBlade (PPB) versus monopolar electrocautery (MPE). This retrospective cohort study included 128 patients with DIEP-based breast reconstruction. Patient characteristics as well as information on the postoperative course were collected and a comparative evaluation was conducted. The MPE group exhibited significantly (p* = 0.0324) higher abdominal drainage volume (351.11 ± 185.96 ml) compared to the PPB group (279.38 ± 183.38 ml). Subgroup analysis demonstrated that PPB significantly reduced postoperative wound fluid in patients with BMI > 30 kg/m² (p* = 0.0284), without prior neoadjuvant chemotherapy (p** = 0.0041), and among non-smokers (p = 0.0046). Furthermore, postoperative pain was significantly (p**** < 0.0001) lower in the PPB cohort. This study confirms the non-inferiority of the PEAK PlasmaBlade to conventional electrocautery for abdominal flap harvesting. The PPB demonstrated advantages, notably reduced drainage volume and lower postoperative pain levels. Recognizing patient subsets that benefit more from the PPB highlights the importance of personalized device selection based on patient characteristics.

In the matrix of bacteria/mitochondria/chloroplasts, Lon acts as the degradation machine for soluble proteins. In stress periods, however, proteostasis and survival depend on the strongly conserved Clp/Hsp100 family. Currently, the targets of ATP-powered unfoldases/disaggregases ClpB and ClpX, and of peptidase ClpP heptameric rings, are still unclear. Trapping experiments and proteome profiling in multiple organisms triggered confusion, so we analyzed the consistency of ClpP-trap targets in bacteria. We also provide meta-analyses of protein interactions in humans, to elucidate where Clp family members are enriched. Furthermore, meta-analyses of mouse complexomics are provided. Genotype-phenotype correlations confirmed our concept. Trapping, proteome, and complexome data retrieved consistent coaccumulation of ClpXP with GFM1 and TUFM orthologs. ClpX shows broad interaction selectivity encompassing mitochondrial translation elongation, RNA granule, and nucleoid; ClpB preferentially attaches to mitochondrial RNA granule and translation initiation components; ClpP is enriched with them all, and associates with release/recycling factors. Mutations in ClpP cause Perrault syndrome, with phenotypes similar to defects in mtDNA/mtRNA. Thus, we propose that ClpB and ClpXP are crucial to counteract misfolded insoluble protein assemblies that contain nucleotide-phosphates. This insight is relevant to improve ClpP-modulating drugs that block bacterial growth, and for the treatment of human infertility, deafness and neurodegeneration.

Objectives: To compare the volumes and shapes of the coagulation zone (CZ) of a multi-probe RFA system (three RFA electrodes) and a single-probe MWA system from the same vendor in an ex-vivo bovine liver model. Material &amp; Methods: A total of 48 CZs were obtained in bovine liver specimens with three different ablation system configurations (single-probe MWA vs. multi-probe RFA with 20 mm inter-probe distance [confluent CZ] vs. multi-probe RFA with 50 mm inter-probe distance [three individual CZ]) at 4-, 6-, 8-, and 10-min ablation time using a fixed ablation protocol. Ablation diameters were measured and ellipticity indices (EI) and volumes calculated. Calculations for all systems/configurations were compared. Results: Volumes and diameters increased with ablation time for all configurations. At 4- and 6-min ablation time volumes obtained with the RFA 50 mm setup, and at 8 and 10 min with the RFA 20 mm setup were the largest with 26.5 ± 4.1 mL, 38.1 ± 5.8 mL, 46.3 ± 4.9 mL, 48.4 ± 7.3 mL, respectively. The single-probe MWA could not reach the volumes of the RFA setups for any of the ablation times evaluated. EI were very similar and almost round for RFA 20 mm and single-probe MWA and differed significantly to the more ovoid ones for the RFA 50 mm configuration. Conclusion: The multi-probe RFA system employing three electrodes achieved significantly larger ablation volumes in both configurations (confluent CZ and three individual CZ) per time as compared to a single-probe MWA system in this ex-vivo bovine liver model.

A Gem-quality rubies and sapphires are often commercially heat treated at about 800°C or higher temperatures to enhance their colour and clarity, and hence quality. For this study, selected corundum samples containing diaspore- and goethite inclusions were heated step-by-step to a maximum of 1000 °C with the aim to monitor the dehydration and phase transformation of these oxyhydroxides to corundum and hematite during heating. Based on our experiments and in agreement with literature, the dehydration of diaspore in corundum occurs between 525 to 550 °C, whereas goethite transforms to hematite already between 300 and 325 °C. As both, diaspore and goethite are common inclusions in rubies, sapphires, and other corundum varieties, these dehydration reactions and phase transformations can be considered important criteria to separate unheated stones from heated ones, specifically in cases in which other methods (e.g. microscopy, FTIR) are unsuccessful.

Phosphorus is required by laying hens for a variety of biological functions. It is usually provided in excess, in a readily digestible inorganic form in diet formulations. However, this does not represent an efficient use of a finite resource and can result in water pollution. Plant bound phosphorus in phytate, is common in commercial poultry diets, and represents an alternate source of phosphorus, however poultry lacks the enzyme to digest it. By adding enzymes to their diets, the availability of this phytate-bound phosphorus can be increased allowing for the reduced inclusion of inorganic P in the diet formulation. Therefore, this study was conducted to examine the effect of a natural enzyme complex that contains phytase and xylanase in layer diets. Novogen Brown Classic layers (n=314) were fed one of two diets: (T1) control diet or (T2) control diet plus a natural mixed-enzyme product with both, phytase and xylanase. Experimental diets were provided for 12 days after which the excreta from each pen were collected for an additional three days to determine total retention and ileal digestibility of phosphorus and gross energy. At the end of the trial the birds were euthanized, and their ileal contents were collected. Productivity parameters were also recorded over the course of the study. The amount of phosphorus detected in the excreta of the control group was significantly higher than the amount detected in the enzyme-supplemented group (P<0.05). Both phosphorus retention and phosphorus ileal digestibility were significantly higher in the enzyme-supplemented birds (P<0.001). Gross energy digestibility was significantly higher in the enzyme-supplemented birds for both the total tract and ileal samples (P<0.001). There were only numerical improvements, not significant, in the layer productivity parameters. This study showed that the enzyme supplement can improve total retention and ileal digestibility of phosphorus and gross energy in older layers.

Mapping and prediction of inundated areas is increasingly important for climate change adaptation and emergency preparedness. Flood forecasting tools and flood risk models have to be compared to observed flooding patterns for training, calibration, validation and benchmarking. At regional to continental scale, satellite earth observation is the established method for surface water extent (SWE) mapping and several operational global-scale data products are available. However, the spatial resolution of satellite-derived SWE maps remains a limiting factor, especially in low-lying areas with complex hydrography, such as Denmark. We collected thermal imagery using an unmanned airborne system (UAS) for three areas in Denmark shortly after major flooding events. We combined the thermal imagery with an airborne lidar-derived high-resolution digital surface model of the country to retrieve high-resolution (40 cm) SWE maps. The resulting SWE maps were compared to low-resolution SWE maps derived from satellite earth observation (EO). We conclude that UAS have significant potential for SWE mapping at intermediate scales, can bridge the scale gap between ground observations and satellite EO and can be used to benchmark and validate SWE mapping products derived from satellite EO as well as models predicting inundation.

Surface velocity is traditionally measured with in situ techniques such as velocity probes (in shallow rivers) or Acoustic Doppler Current Profilers (in deeper water). In the last years, researchers have developed remote sensing techniques, both optical (e.g., image-based velocimetry techniques) and microwave (e.g., Doppler radar). These techniques can be deployed from Unmanned Aerial Systems (UAS), which ensure fast and low-cost surveys also in remotely-accessible locations. We compare the results obtained with a UAS-borne Doppler radar and UAS-borne Particle Image Velocimetry (PIV) in different rivers, which presented different hydraulic–morphological conditions (width, slope, surface roughness and sediment material). The Doppler radar was a commercial 24 GHz instrument, developed for static deployment, adapted for UAS integration. PIV was applied with natural seeding (e.g., foam, debris) when possible, or with artificial seeding (woodchips) in the stream where the density of natural particles was insufficient. PIV reconstructed the velocity profile with high accuracy typically in the order of a few cm s⁻¹ and a coefficient of determination (R²) typically larger than 0.7 (in half of the cases larger than 0.85), when compared with acoustic Doppler current profiler (ADCP) or velocity probe, in all investigated rivers. However, UAS-borne Doppler radar measurements show low reliability because of UAS vibrations, large instrument sampling footprint, large required sampling time and difficult-to-interpret quality indicators suggesting that additional research is needed to measure surface velocity from UAS-borne Doppler radar.

Vision impairment may delay responses to hazards when driving. In a proof-of-concept driving simulator study, we evaluated a hazard warning device designed for vision impaired drivers. Three groups participated: 11 persons with central vision loss (CVL; median age 60 years), 12 with homonymous field loss (HFL; 52 years) and 11 with normal vision (NV; 60 years). CVL is characterised by impaired visual acuity and contrast sensitivity while HFL is a loss of vision in the same half of the visual field (blind side) in both eyes. Participants completed drives with and without the device which gave a directional vibro-tactile warning for an approaching pedestrian hazard when collision risk exceeded a pre-defined threshold. Warnings significantly (p< 0.001) reduced brake response times for CVL (∆= 0.54s) and HFL (∆= 0.30s), but not NV participants. For HFL participants, the reduction was greater (p = 0.02) for hazards on the blind (∆= 0.57s) than seeing side (∆= 0.10s). The warnings significantly reduced collision rates for CVL participants from 11 to 0% (all hazards) and for HFL participants from 30 to 1.7% (blind side hazards). Thus, hazard warnings may be beneficial in improving safety of vision impaired drivers; further research is warranted.

The present article analyzes the integration of green building policy and practice with the largest low-income housing production program in the US and the innovativeness of its housing agencies. Drawing on policy innovation literature, panel data and regression analysis are employed to quantify associations between state-level characteristics and the adoption of green building criteria into the Low-Income Housing Tax Credit (LIHTC) program. Results show that, on average, housing agencies have increasingly adopted green building criteria, and most have identified co-benefits from energy-efficient buildings and smart growth. Despite overall progress, the rate of adoption of green building criteria has decreased, few states have comprehensive criteria, and many have dropped important criteria, such as on-site renewable energy generation. Results are consistent with hypotheses derived from the literature and suggest the integration of green building with LIHTC developments is significantly associated with government motivation, financial resources, and exogenous characteristics that affect the demand for green building. Future research should explore organization-level factors that affect environmental policy innovation. It is recommended that LIHTC housing agencies require compliance with green building rating systems and periodically reconfigure green building criteria based on planned evolutionary change, data-driven strategies, and life-cycle analyses towards zero net energy consumption.

The ability to predict the skin sensitization potential of small organic molecules is of high importance to the development and safe application of cosmetics, drugs and pesticides. One of the most widely accepted methods for predicting this hazard is the rodent local lymph node assay (LLNA). The goal of this work was to develop in silico models for the prediction of the skin sensitization potential of small molecules that go beyond the state of the art, with larger LLNA data sets and, most importantly, a robust and intuitive definition of the applicability domain, paired with additional indicators of the reliability of predictions. We explored a large variety of molecular descriptors and fingerprints in combination with random forest and support vector machine classifiers. The most suitable models were tested on holdout data, on which they yielded competitive performance (Matthews correlation coefficients up to 0.52; accuracies up to 0.76; areas under the receiver operating characteristic curves up to 0.83). The most favorable models are available via a public web service at https://nerdd.zbh.uni-hamburg.de/skinDoctor/ that, in addition to predictions, provides assessments of the applicability domain and indicators of the reliability of the individual predictions.

This study reports an empirical analysis of an all-electric, Net Zero Energy Housing (NZEH) development located in a mixed-humid climate zone (4A, Virginia, USA). Circuit-level energy monitors were used to measure energy consumption and energy production data (solar photovoltaic) at 1-hr intervals in six identical apartments over 24 months. The study employs a multi-step case study methodology to a) empirically evaluate energy consumption and production data, b) identify the temporal variability of energy consumption and production data at different time scales, c) understand the impact(s) of weather and human-building interaction on energy consumption and production, and d) synthesize the study’s “lessons learned” toward data-driven recommendations for future NZEH researchers and practitioners. The study found that the development’s net zero energy goal was achieved in three of six case units and that NZEH housing performance was more influenced by human-building interaction than weather variability. The analysis also found the solar photovoltaic (PV) performance to be reliable across the sampled units over the periods of measurement, suggesting that solar PV could be oversized as an approach to overcome verifiability in HBI and achieve NZEH performance goals.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

The inherent dependency of deep learning models to labeled data is a well-known problem and one of the barriers that slows down the integration of such methods into different fields of applied sciences and engineering, in which experimental and numerical methods can easily generate a colossal amount of unlabeled data. This paper proposes an unsupervised domain adaptation methodology that mimics the peer review process to label new observations in a different domain from the training set. The approach evaluates the validity of a hypothesis using domain knowledge acquired from the training set through a similarity analysis, exploring the projected feature space to examine the class centroid shifts. The methodology is tested on a binary classification problem, where synthetic images of cubes and cylinders in different orientations are generated. The methodology improves the accuracy of the object classifier from 60% to around 90% in the case of a domain shift in physical feature space without human labeling.

The illegal use of explosives by terrorists and other criminals is an increasing issue in public spaces, such as airports, railway stations, highways, sports arenas, theaters, and other large buildings. Security in these environments can be achieved by a set of different means, including the installation of scanners and other analytical devices to detect ultra-small traces of explosives in a very short time-frame to be able to take action as early as possible to prevent the detonation of such devices. Unfortunately, an ideal explosive detection system still does not exist, which means that a compromise is needed in practice. Most detection devices lack the extreme analytical sensitivity, which is nevertheless necessary due to the low vapor pressure of nearly all explosives. In addition, the rate of false positives needs to be virtually zero, which is also very difficult to achieve. Here we present an immunosensor system based on kinetic competition, which is known to be very fast and may even overcome affinity limitation, which impairs the performance of many traditional competitive assays. This immunosensor consists of a monolithic glass column with a vast excess of immobilized hapten, which traps the fluorescently labeled antibody as long as no explosive is present. In the case of TNT occurring, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled CMOS camera. Liquid handling is performed with high-precision syringe pumps and chip-based mixing-devices and flow-cells. The system achieved limits of detection of 1 pM (1 ppt) of the fluorescent label and around 100 pM (20 ppt) of the explosive 2,4,6-trinitrotoluene (TNT). The total assay time is less than 8 min. A cross-reactivity test with 5000 pM solutions showed no signal by PETN, RDX, and HMX. This immunosensor belongs to the most sensitive and fastest detectors for TNT with no significant cross-reactivity by non-related compounds.

Accidents between right-turning commercial vehicles and crossing vulnerable road users (VRU) in urban environments often lead to serious or fatal injuries and therefore play a significant role in forensic accident analysis. To reduce the risk of accidents, blind spot assistance systems have been installed in commercial vehicles for several years, among other things, to detect VRUs and warn the driver in time. However, since such systems cannot reliably prevent all turning accidents, an investigation by experts must clarify how the accident occurred and to what extent the blind spot assistance system influenced the course of the accident. The occurrence of the acoustic warning message can be defined as an objective reaction prompt for the driver, so that the blind spot assistance system can significantly influence the avoidability assessment. In order to be able to integrate the system into forensic accident analysis, a precise knowledge of how the system works and its limitations is required. For this purpose, tests with different systems and accident constellations were conducted and evaluated. It was found that the type of sensor used for the assistance systems has a great influence on the system’s performance. The lateral distance between the right side of the commercial vehicle and the VRU as well as obstacles between them and the speed difference can take great influence on the reliability of the assistance system. Depending on the concrete time of the system’s warning signal the accident can be avoided or not by the driver when reacting on this signal.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

Digital federated platforms and data cooperatives for secure, trusted and sovereign data exchange will play a central role in the construction industry of the future. With the help of platforms, cooperatives and their novel value creation, the digital transformation and the degree of organization of the construction value chain can be taken to a new level of collaboration. The goal of this research project was to develop an experimental prototype for a federated innovation data platform along with a suitable exemplary use case. The prototype is to serve the construction industry as a demonstrator for further developments and form the basis for an innovation platform. It exemplifies how an overall concept is concretely implemented along one or more use cases that address high-priority industry pain points. This concept will create a blueprint and a framework for further developments, which will then be further established in the market. The research project illuminates the perspective of various governance innovations to increase industry collaboration, productivity and capital project performance and transparency as well as the overall potential of possible platform business models. However, a comprehensive expert survey revealed that there are considerable obstacles to trust-based data exchange between the key stakeholders in the industry value network. The obstacles to cooperation are predominantly not of a technical nature, but of a competitive, predominantly trust-related nature. To overcome these obstacles and create a pre-competitive space of trust, the authors therefore propose the governance structure of a data cooperative model, which is discussed in detail in this paper.

The monitoring of sick newborns is a challenging task that health care providers in Neonatal Intensive Care Units (NICU) must contend with each day. Conventionally, newborns are monitored via probes that are affixed to their skin and attached to processing monitors (Fig.1). However, an alternative exists in contactless imaging to record such physiological signals (Physio-Markers), surface changes and internal structures which can be used independently of, or in conjunction with conventional monitors. Advantages of contactless monitoring methods include: i) quick data generation; ii) lack of contact with skin, which reduces skin breakdown and decreases risk of infection; and iii) minimizing the number of probes and monitors affixed to the skin, which allows greater body surface-area for other care. This paper is an attempt to build a foundation for and to provide a vision of the potential neonatal clinical applications of technologies that use non-contact modalities such as Visible Light Imaging (VLI), Near InfraRed Spectrum (NIRS), and Thermal Imaging (TI) using InfraRed Spectrum (IRS).

To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

The term `motor control´ encompasses a wide range of mechanisms thought to be implicated in the organization of movements. Their study, like that of any other scientific field, must use specific notions to get to grips with them. This review is therefore organized along a series of notions that are frequently used in motor control, and we will discuss them with particular emphasis on neurological conditions, which may disrupt normal motor functioning. We will start with a short description of the roles of space and time, in which movements take place. Subsequently we will deal with kinematics and kinetics (dynamics) of movements. Then, we will list the inputs to motoneurons (MNs), which, in different forms, convey signals from the central nervous system (CNS) to skeletal muscles and muscle spindles, including central pattern generators (CPGs), sensory inputs and supraspinal descending fiber systems. Some helpers in movement organization will be introduced, such as internal models and neuronal network models. A relatively brief section on sensory-motor learning will follow because learning abilities are required to endow the sensory-motor system with flexibility and adaptability. The major emphasis is placed on neurological processes, which result from genetic modifications, autoimmune diseases, neurodegenerative diseases, infections in the nervous system as well as vascular and traumatic lesions. These neurological diseases lead to a variety of impairments and symptoms, particularly movement derangements including cerebellar ataxia, spasticity, and (other) movement disorders such as Parkinson’s syndromes. The conclusion is that there is no unique top controller that controls ´motor control`.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

Optical conductivity of an interacting polaron gas is calculated within an extended random phase approximation which takes into account mixing of collective excitations of the electron gas with LO phonons. This mixing is important for the optical response of strongly polar crystals where the static dielectric constant is rather high, as in the case of strontium titanate. The present calculation sheds light on unexplained features of experimentally observed optical conductivity spectra in $n$-doped SrTiO$_{3}$. These features appear to be due to dynamic screening of the electron-electron interaction by polar optical phonons and hence do not require additional mechanisms for their explanation.

Accurate transfer learning of clinical outcomes, e.g., of the effects and side effects of drugs or other interventions, from one cellular context to another (in-vitro versus ex-vivo versus in-vivo, or across tissues), between cell-types, developmental stages, omics modalities or species, is considered tremendously useful. Ultimately, it may avoid most drug development failing in translation, despite large investments in the preclinical stages, which includes animal experiments requiring careful justification. Thus, when transferring a prediction task from a source (model) domain to a target domain, what counts is the high quality of the predictions in the target domain, requiring molecular states or processes common to both source and target that can be learned by the predictor, reflected by latent variables. These latent variables may form a compendium of knowledge that is learned in the source, to enable predictions in the target; usually, there are few, if any, labeled target training samples to learn from. Transductive learning then refers to the learning of the predictor in the source domain, transferring its outcome label calculations to the target domain, considering the same task. Inductive learning considers cases where the target predictor is performing a different yet related task as compared to the source predictor, making some labeled target data necessary. Often, there is also a need to first map the variables in the input/feature spaces (e.g. of gene names to orthologs) and/or the variables in the output/outcome spaces (e.g. by matching of labels). Transfer across omics modalities also requires that the molecular information flow connecting these modalities is sufficiently conserved. Only one of the methods for transfer learning we reviewed offers an assessment of input data, suggesting that transfer learning is unreliable in certain cases. Moreover, source domains feature their very own particularities, and transfer learning should consider these, e.g., as differences in pharmacokinetics, drug clearance or the microenvironment. In light of these general considerations, we here discuss and juxtapose various recent transfer learning approaches, specifically designed (or at least adaptable) to predict clinical (human in-vivo) outcomes based on molecular data, towards finding the right tool for a given task, and paving the way for a comprehensive and systematic comparison of the suitability and accuracy of transfer learning of clinical outcomes.

Using the unique combination of atomically resolved atom probe tomography (APT) and volume averaged neutron (resonance) spin echo (NRSE and NSE) experiments, the influence of nano-scaled clusters on the spin relaxation in spin glasses was studied. For this purpose, the phase transition from the paramagnetic phase to the spin glass phase in a Fe-Cr spin glass with a composition of Fe_17.8Cr_82.2 was studied in detail by means of NRSE. The microstructure was characterised by APT measurements, which show local concentration fluctuations of Fe and Cr on a length scale of 2 to 5 nm, which lead i) to the coexistence of ferro- and anti-ferromagnetic clusters and ii) a change of the magnetic properties of the whole sample, even in the spin glass phase, where spins are supposed to be randomly frozen. We show that a generalized spin glass relaxation function, which was successfully used to describe the phase transition in diluted spin glasses, can also be used for fitting the spin dynamics in spin glasses with significant concentration fluctuations.

Patients with sAID are a population at high risk of severe COVID outcomes but evidence on the efficacy of SARS-CoV-2 vaccination in this group of patients is scarce. To investigate the efficacy of SARS-CoV-2 vaccination in patients with systemic autoinflammatory diseases (sAID) receiving interleukin-1 inhibition is important. Vaccination responses from 100 sAID patients most of whom were treated with IL-1inhibitors (N=96) and 100 healthy controls (HC) were ana-lyzed. After 2nd SARS-CoV-2 vaccination, sAID patients showed similar anti-SARS-CoV-2 anti-body responses (mean (SD): 6.7 (2.7)) compared to HC (5.7 (2.4)) as well as similar neutralizing antibodies (85.1 ±22.9% vs. 82.5 ±19.7%). Anti-SARS-CoV-2 antibody responses and neutralizing antibodies were similar in sAID patients after SARS-CoV-2 infection and double vaccination. Furthermore, while antibodies increased after 1st and 2nd vaccination in sAID patients they did not further increase after 3rd and 4th vaccination. No difference was found in antibody responses between anakinra and anti-IL-1 antibody treatments and also the additional use of colchicine or other drugs did not impair vaccination responses. Primary and booster SARS-CoV-2 vaccination lead to protective antibody responses in sAID patients, which are at the same level of vaccination responses in HC and in sAID patients after SARS-CoV-2 infection. Immunomodulatory treatments used in sAID do not seem to affect antibody responses to the SARS-CoV-2 vaccine.

State-of-the-art dielectrophoretic (DEP) separation techniques provide unique properties to separate particles from a liquid or particles with different properties such as material, morphology or size from each other. However, such separators do not operate at throughput that is sufficient for a vast fraction of separation tasks. The reason for this limitation is that, in order to move particles by dielectrophoresis, high electric field gradients to drive the separation are required. Conventionally, those gradients are generated by electrode microstructures that limit the maximum channel size. Here, we investigate DEP filtration, a technique that uses open porous microstructures instead of microfluidic devices to easily increase the filter cross section and therefore also the processable throughput by several orders of magnitude. Previously, we already separated baker’s yeast by DEP filtration in open porous ceramic structures. Now, we give a more elaborate experimental study about DEP filtration in these open porous structures and separate model particles, that are an order of magnitude smaller (500 nm, polystyrene), from aqueous suspensions. Almost 100% separation at flow rates of up to 9 mL min^-1 was achieved while the majority of the trapped particles could be recovered. We show how particle separation depends on key parameters (voltage, throughput, filter structure size). Further, we work towards selective particle separation and show that particle separation is very dependent on the particle polarizability: This creates the possibility to adjust selectivity by changing the electrical conductivity of the suspension around that of the particle. This study highlights the unique qualities of dielectrophoretic filtration enabling switchable, selective, and scalable particle separation to solve existing problems such as cell separation or precious metal recovery.

The most important predictors for outcomes after ischemic stroke, that is, for health deterioration and death, are chronological age and stroke severity; gender, genetics and lifestyle / environmental factors also play a role. Of all these, only the latter can be influenced after the event, even though recurrent stroke may be prevented by antiaggregant/anticoagulant therapy, angioplasty of high-grade stenoses, and treatment of cardiovascular risk factors. Moreover, blood cell composition and protein biomarkers such as C-reactive protein or interleukins in serum are frequently considered as biomarkers of outcome. We surveyed protein biomarkers that were reported to be predictive for outcome after ischemic stroke, specifically considering biomarkers that predict long-term outcome (≥3 months) and that are measured over the first days following the event. We classified the protein biomarkers as immune‑inflammatory, coagulation-related, and adhesion-related biomarkers. Some of these biomarkers are closely related to cellular senescence and, in particular, to the inflammatory processes that can be triggered by senescent cells. Moreover, the processes that underlie inflammation, hypercoagulation and cellular senescence connect stroke to cancer, and biomarkers of cancer-associated thromboembolism, as well as of sarcopenia, overlap strongly with the biomarkers discussed here. Finally, we demonstrate that most of the outcome-predicting protein biomarkers form a close-meshed functional interaction network, suggesting that the outcome after stroke is partially determined by an interplay of molecular processes relating to inflammation, coagulation, cell adhesion and cellular senescence.

Effectively mapping and monitoring rubber plantation is still changing. Previous studies have explored the potential of phenology features for rubber plantation mapping through a pixel-based approach (pixel-based phenology approach). However, in fragmented mountainous Xishuangbanna, it could lead to noises and low accuracy of resultant maps. In this study, we investigated the capability of an integrated approach by combining phenology information with an object-based approach (object-based phenology approach) to map rubber plantations in Xishuangbanna. Moderate Resolution Imaging Spectroradiometer (MODIS) data were firstly used to acquire the temporal profile and phenological features of rubber plantations and natural forests, which delineates the time windows of defoliation and foliation phases. Landsat images were then used to extract a phenology algorithm comparing three different approaches: pixel-based phenology, object-based phenology, and extended object-based phenology to separate rubber plantations and natural forests. The results showed that the two object-based approaches achieved higher accuracy than the pixel-based approach, having overall accuracies of 96.4%, 97.4%, and 95.5%, respectively. This study proved the reliability of a phenology-based rubber mapping in fragmented landscapes with a distinct dry/cool season using Landsat images. This study indicated that the object-based phenology approaches can effectively improve the accuracy of the resultant maps in fragmented landscapes.

Proximal Junctional Kyphosis (PJK) as one of the most discussed problems after corrective surgery in adolescent idiopathic scoliosis (AIS), is still not fully clarified and seems to be multifactorial. Biome-chanical and few clinical studies have shown the influence of destruction of posterior ligaments by re-section of spinous processes and some parameters concerning rod contouring as risk factors for PJK. To verify these results 192 patients with AIS and corrective surgery via posterior approach between 2009 and 2017 were included. Radiographic parameters were analyzed preoperatively (preOP), postoperatively (postOP), and with a mean follow up (FU) of 27 months. The participants were divided into two groups (PJK group and non-PJK group). The incidence of PJK was 15.6%. Contrary to the results of biomechanical studies, we could not find any significant influence of the spinous process resection. However, the PJK group had significantly larger preOP T4-T12 kyphosis (31.1°±13.93° vs. 23.3°±14.93°, p=.016). Furthermore, the PJK group showed a significantly larger rod contour angle (RCA) (8.0°±4.44° vs. 5.9°±3.28°, p=.003) and mismatch of postOP proximal junctional angle (PJA) and RCA (3.5°±5.72° vs. 0.9°±4.86°, p=.010) compared to the non-PJK group. An increase of the mismatch of postOP PJA and RCA (OR=1.14, p=.008) and a high RCA are risk factors for PJK and need to be focused on by surgeons.

Providing data on usage patterns is key to assessing the reduced-risk potential of novel tobacco and nicotine products at a population level. We performed a nationwide cross-sectional survey of the general population in Japan to assess usage patterns after the introduction of tobacco heating products (THPs). Eligible participants were Japanese residents, aged 20 years or older who consented to complete the survey. Individuals living in institutions were excluded. A three-stage probability sampling method was applied that was geographically stratified by street blocks proportionate to population density. Respondents self-reported patterns of product use and reasons for THP use. Complete responses were available from 5,306 individuals, of whom 933.5 (17.6%) were current users, 984.2 (18.5%) were former users and 3388.4 (63.9%) were never users of tobacco products. Cigarettes were used by 14.6% of current tobacco product users and THPs by 5.3%. Cigarettes and THPs were used exclusively by 64.5% and 12.2%, respectively, and both were used by 12.7%. The most common reasons reported for THP use were perceived reduction in harm to self and others compared to cigarettes. While the prevalence of cigarette use in Japan is decreasing, THPs seem to be increasingly used as long-term alternatives to cigarette smoking.

We addressed the frequent occurrence of mixed-chain lipids in biological membranes and their impact on membrane structure by studying several chain-asymmetric phosphatidylcholines and the highly asymmetric milk sphingomyelin. Specifically, we report trans-membrane structures of the corresponding fluid lamellar phases using small-angle X-ray and neutron scattering, which were jointly analyzed in terms of a membrane composition-specific model, including a headgroup hydration shell. Focusing on terminal methyl groups at the bilayer center we found a linear relation between hydrocarbon chain length mismatch and the methyl-overlap for phosphatidylcholines, and a non-negligible impact of the glycerol backbone-tilting, letting the sn1-chain penetrate deeper into the opposing leaflet by half a CH2 group. That is, penetration-depth differences due to the ester-linked hydrocarbons at the glycerol backbone, reported previously for gel phase structures also extend to the physiological more relevant fluid phase, but are significantly reduced. Moreover, milk sphingomyelin was found to follow the same linear relationship suggesting a similar tilt of the sphingosine backbone. Complementary performed molecular dynamics simulations revealed that there is always a part of the lipid tails bending back, even if there is a high interdigitation with the opposing chains. This suggests that hydrocarbon chain interdigitation plays only a minor role in transbilayer coupling. For both cases of adaption to chain length mismatch, chain-asymmetry has a large impact on hydrocarbon chain ordering, inducing disorder in the longer of the two hydrocarbons.

The transportation sector significantly contributes to greenhouse gas emissions, thus imposing sig-nificant environmental hazards. In response, many nations have begun promoting Electric Vehicles (EVs) as an ecologically sustainable substitute for traditional combustion vehicles. Lithium-Ion Batteries (LIBs), characterized by their high energy density, extended lifespan, and relatively low self-discharge rate, have become the suitable energy storage system for EVs, advancing the field of sustainable transportation. The decreasing cost of LIB production has primarily driven this progression, realized through a combination of economies of scale, advancements in electrode materials and cell design, and re-finements in manufacturing processes. All these elements collectively contribute to the cost reduc-tion of LIBs. A foreseeable implication of this trend is an expected surge in LIBs that will exhaust their operational lifespan and, consequently, be cast away into the environment. One mitigating strategy for this impending environmental issue involves collecting these spent EV batteries, re-configuring them, and repurposing them for applications with less rigorous weight, performance, and size prerequisites. This approach would not only prolong the utility life of the batteries but also ameliorate their environmental impacts. Nevertheless, second-life batteries are anticipated to exhibit a higher rate of gas evolution, necessitating comprehensive testing and readjustments to ensure safe operation in secondary ap-plications. The regulatory framework encompassing the second-life battery sector still needs to be defined regarding norms, technical standards, and legislation. This paper aims to elucidate the primary regulations and technical standards proposed thus far in the second-life battery marketplace. The results underscore the exigency for neutral evaluative entities, such as universities, research centers, and governmental institutions, to perform an unbi-ased assessment of the second-life battery market. This would pave the way for novel technical standards and legislative measures specifically tailored to this emerging sector.

Structure quality of LuFeO3 epitaxial layers grown by pulsed-laser deposition on sapphire substrates with and without platinum interlayers has been investigated by in-situ high-resolution x-ray diffraction (reciprocal-space mapping). The parameters of the structure such as size and misorientation of mosaic blocks have been determined as functions of the thickness of LuFeO3 during the PLD growth and for different platinum interlayers thicknesses up to 40 nm. The x-ray diffraction results combined with ex-situ scanning electron microscopy and high-resolution transmission electron microscopy demonstrate that the Pt interlayer significantly improves the structure of LuFeO3 by reducing the misfit of the LuFeO3 lattice with respect to the material underneath.

Ataxin-2 (human gene symbol ATXN2, protein ATXN2) is the disease protein of Spinocerebellar Ataxia type 2 (SCA2). The large expansions of a polyglutamine (polyQ) stretch above a threshold of ~33 glutamines cause the multi-system nervous atrophy SCA2, while intermediate expansions of 29-32 glutamines contribute to the risk of the motor neuron diseases Amyotrophic Lateral Sclerosis (ALS) and Fronto-Temporal Lobar Dementia (FTLD). To elucidate the cellular function of ATXN2, we further characterized its direct interaction with alpha-Actinin-1 (symbol ACTN1), which had been observed in high-throughput yeast-two-hybrid surveys. An endogenous complex of ATXN2 and ACTN1 proteins was detected by co-immunoprecipitation. In vitro GST-tag pull-down experiments showed that the Calponin-Homology-domain at the N-terminus of ACTN1 binds to the N-terminus of ATXN2. Although an impact of the polyQ expansion on the interaction was not evident in pull-down experiments, a recent characterization of aged Atxn2-CAG100-KnockIn mice provides evidence. Both proteins associated in the cytosol and at the plasma membrane, as determined by sedimentation experiments in mouse brain, and by immunofluorescence microscopy of a transfected monkey cell line and of rat primary hippocampal neurons. In view of the roles of ACTN1 for spine plasticity and postsynaptic receptor control via reassembly of cortical actin, our data help to explain the impaired dendrite maintenance in SCA2.

Pain is a major problem in sick newborn infants, especially for those needing intensive care. Pharmacological pain relief is the most commonly used but may be ineffective, have side effects, including long-term neurodevelopmental sequelae. The effectiveness and safety of alternative analgesic methods are ambiguous. The objective is to review the effectiveness and safety of non-pharmacological methods of pain relief in newborn infants and to identify those that are the most effective. PubMed and Google Scholar were searched using the terms: ‘infant’, ‘premature’, ‘pain’, ‘acupuncture’, ‘skin to skin contact’, ‘sucrose’ ‘massage’, ‘musical therapy’ and ‘breastfeeding’. We included 24 studies assessing different methods of non-pharmacological analgesic techniques. Most resulted in some degree of analgesia but many were ineffective and some were even detrimental. Sucrose, for example, was often ineffective but more effective than music therapy, massage, breast milk (for extremely premature infants) or non-invasive electrical stimulation acupuncture. There were also conflicting results for acupuncture, skin to skin care and musical therapy. Most non-pharmacological methods of analgesia provide some modicum of relief for preterm infants but none are completely effective and there is no clearly superior method. Study is also required to assess potential long-term consequences of any of these methods.

The scarcely investigated myxobacterium Corallococcus coralloides holds a large genome containing many uncharacterized biosynthetic gene clusters (BGCs) that potentially encode the synthesis of entirely new natural products. Despite its promising genomic potential, suitable cultivation conditions have not yet been found to activate the synthesis of new secondary metabolites (SMs). Finding the right cultivation conditions to activate BGCs in the genome remained a major bottleneck and its full biosynthetic potential was so far not retrieved. Here, we therefore applied a bivariate OSMAC approach, using a combination of two elicitor changes at once for activation of BGCs and concomitant SM production by C. coralloides. The bivariate OSMAC screening was carried out in 24-well System Duetz-plates, applying univariate and bivariate OSMAC conditions. We combined biotic additives and organic solvents with minimal media and complex growth medium. The success of the method was evaluated by the number of new mass features detected in the respective extracts. We found synergistic effects in bivariate OSMAC designs. The number of new mass features detected in bivariate OSMAC exceeded the sum of new mass features found in the respective univariate OSMAC with only one elicitor. Overall, the bivariate OSMAC screening led to 26 new mass features, which were not detected in the univariate OSMAC design. Hence, the presence of multiple elicitors in the bivariate OSMAC designs successfully activated the biosynthetic potential in C. coralloides. We propose the bivariate OSMAC designs with a complex combination of elicitors as a straightforward strategy to robustly expand the SM space of microorganisms with large genomes.

The emergence of carbapenemase-producing Enterobacteriaceae has limited therapeutic options and presents a major public health problem. Resistances against carbapenems in this bacterial family are mostly conveyed by metallo-beta-lactamases (MBL) including VIM, which are often encoded on resistance plasmids. We characterized four VIM-positive isolates that were obtained as part of a routine diagnostic screening from two laboratories in north-eastern Germany be-tween June and August 2020. Whole-genome sequences were generated to address a) their phylo-genetic properties, b) their plasmid content, and c) the underlying mechanisms of resistance and virulence. In addition, we performed phenotypic antibiotic and mercury resistance analyses. The genomic analysis revealed three different bacterial species including C. freundii, E. coli and K. oxytoca with four different sequence types. All isolates were geno- and phenotypically multi-drug-resistant (MDR). Three isolates of four carried identical VIM-1-resistance plasmids, which – in addition – encoded for a mercury resistance operon and showed some similarity to two ex-ternal plasmid sequences. The distribution of virulence features among the genomes was limited. Our results highlight the circulation of an identical VIM-1-resistance plasmid in three of four bacterial isolates of different Enterobacteriaceae in north-eastern Germany.

Hands-on type training of Integrated Computational Materials Engineering (ICME) is characterized by assisted application and combination of multiple simulation software tools and data. In this paper, we present recent experiences in establishing a cloud-based infrastructure to enable remote use of dedicated commercial and open access simulation tools during an interactive on-line training event. In the first part, we summarize the hardware and software requirements and illustrate how these have been met using cloud hardware services, a simulation platform environment, a suitable communication channel, common workspaces and more. The second part of the article focuses (i) on the requirements for suitable on-line hands-on training material and (ii) on details of some of the approaches taken. Eventually, the practical experiences made during three consecutive on-line training courses held in September 2020 with 35 nominal participants each, are discussed in detail.

Research on healthy ageing shows that lifespan reductions are often caused by mitochondrial dysfunction. Thus, it is very interesting that the deletion of mitochondrial matrix peptidase LonP1 was observed to abolish embryogenesis, while deletion of the mitochondrial matrix peptidase ClpP prolonged survival. To unveil the targets of each enzyme, we documented the global proteome of LonP1^+/- mouse embryonal fibroblasts (MEF), for comparison with ClpP^-/- depletion. Proteomic profiles of LonP1^+/- MEF generated by label-free mass spectrometry were further processed with the STRING webserver Heidelberg for protein interactions. ClpP was previously reported to degrade Eral1 as a chaperone involved in mitoribosome assembly, so ClpP deficiency triggers accumulation of mitoribosomal subunits and inefficient translation. LonP1^+/- MEF also showed Eral1 accumulation, but no systematic effect on mitoribosomal subunits. In contrast to ClpP^-/- profiles, several components of the respiratory complex I membrane arm were accumulated, whereas the upregulation of numerous innate immune defense components was similar. Overall, LonP1 as opposed to ClpP appears to have no effect on translational machinery, instead it shows enhanced respiratory dysfunction; this agrees with reports on the human CODAS syndrome caused by LonP1 mutations.

Lifespan extension was recently achieved in Caenorhabditis elegans nematodes by mitochondrial stress and mitophagy, triggered via iron depletion. Conversely in man, deficient mitophagy due to Pink1/Parkin mutations triggers iron accumulation in patient brain and limits survival. We now aimed to identify murine fibroblast factors, which adapt their mRNA expression to acute iron manipulation, relate to mitochondrial dysfunction and may influence survival. After iron depletion, expression of the plasma membrane receptor Tfrc with its activator Ireb2, the mitochondrial membrane transporter Abcb10, the heme-release factor Pgrmc1, the heme-degradation enzyme Hmox1, the heme-binding cholesterol metabolizer Cyp46a1, as well as the mitophagy regulators Pink1 and Parkin showed a negative correlation to iron levels. After iron overload, these factors did not change expression. Conversely, a positive correlation of mRNA levels with both conditions of iron availability was observed for the endosomal factors Slc11a2 and Steap2, as well as for the iron-sulfur-cluster (ISC)-containing factors Ppat, Bdh2 and Nthl1. Positive correlation only after iron depletion was observed for the iron export factor Slc40a1, mitochondrial iron transporters Slc25a28, Abcb7 and Abcb8, mitochondrial ISC-containing factors Glrx5, Nfu1, Bola1 and Abce1, cytosolic Aco1 and Tyw5, as well as nuclear Dna2, Elp3, Pold1 and Prim2. The latter are regulators of nucleotide synthesis and DNA quality control, which have known importance for growth and lifespan. The only Pink1-/- triggered transcript modulation was the reduced expression of the ISC-containing ribosomal factor Abce1. These mammalian findings support previous fly data that Pink1 influences co-translational quality control via Abce1, as well as mitophagy. Our findings provide the first systematic survey how iron dosage triggers homeostatic transcriptional regulations and elucidate how iron deprivation results in mitophagy.

Thin supported inorganic mesoporous membranes are used for removal of salts, small molecules (PFAS, dyes, polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nano-filtration membranes can reject simple salts with 80-100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received par-ticular interest due to their (potential) stability at operational conditions and defouling operations. More recently membranes with extreme stability became interesting with the advent of in-situ fouling mitigation by means of ultrasound, emitted from within the membrane structure. For this reason we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, mag-netite membranes none were actually stable at all test conditions. In earlier work, it was already established that meso-porous alumina membranes have very poor stability. A new nano-filtration membrane was made of cubic zirconia membranes that exhibited a near perfect stability. A new ultra-filtration membrane was made of amorphous silica that was fully stable in ultrapure water at 80°C. This work provides details of membrane synthesis, stability characterization and actual sta-bility data.

Blood-derived products (BP) like citrate-platelet-rich plasma (CPRP) or hyperacute serum (HAS) are known to contain many growth factors. Combined mitogenic and DNA damaging stimuli might lead to increased senescent cell burden and altered senescence-associated secretory pheno-type (SASP). Therefore, the senescent state was extensively tested by γH2AX staining, p21 Q-PCR and western blot, growth curves and senescence associated ß-galactosidase staining. Two main treatments with BP were performed early (immediately after etoposide) and late (after addition-al 11days). Effects of the BP treatment was evaluated by IL-6 and IL-8 measurement as well as collagen (COL1) and p21 mRNA expression. Additionally, XTT assays, cell size measurements, viability assays, and cell number calculations were performed. HAS treated cells in early treat-ment had the lowest observed IL-6 and IL-8. In contrast, there was a clear inflammatory response for IL-8 on HAS and CPRP treated cells in late treatment. For COL1 expression an upregulation in early treatment could be shown, meanwhile cells in the late treatment group remained unaf-fected. In CPRP treated cells, the COL1 expression decreased. All in all, BP treatment seems to have slightly positive effects regarding skin rejuvenation.

Lipophilic oligonucleotide derivatives are a potent approach to the intracellular delivery of nucleic acids. The binding of these derivatives to serum albumin is a major determinant of their fate in the body, as its structure contains several sites of high affinity for hydrophobic compounds. This study focuses on the features of self-association and non-covalent interactions with human serum albumin of novel self-penetrating oligonucleotide derivatives. The study revealed that the introduction of a triazinyl phosphoramidate modification bearing two dodecyl groups at the 3' end region of the oligonucleotide sequence has a negligible effect on its affinity for the complementary sequence. Dynamic light scattering verified that the amphiphilic oligonucleotides under study can self-assemble into micelle-like particles ranging from 8 to 15 nm in size. The oligonucleotides with dodecyl groups form stable complexes with human serum albumin with a dissociation constant of approximately 10-6 M. The oligonucleotide micelles are simultaneously destroyed upon binding to albumin. Using an electrophoretic mobility shift assay and affinity modification, we examined the ability of DNA duplexes containing triazinyl phosphoramidate oligonucleotides to interact with Ku antigen and PARP1, as well as the mutual influence of PARP1 and albumin or Ku antigen and albumin upon interaction with DNA duplexes. These findings, together with the capability of dodecyl-containing derivatives to effectively penetrate different cells, such as HEK293 and T98G, indicate that the oligonucleotides under study can be considered as a platform for the development of therapeutic preparations with a target effect.

As common industrial by-products, airborne engineered nanomaterials are considered important environmental toxicants to monitor due to their potential health risks to humans and animals. The main uptake routes of airborne nanoparticles are nasal and/or oral inhalation, which are known to enable the transfer of nanomaterials into the blood stream resulting in rapid distribution in the body. Consequently, mucosal barriers present in nose, buccal and lung have been identified and intensively studied as the key tissue barrier to nanoparticle translocation. Despite decades of research, surprisingly little is known about the differences among various mucosa tissue types to tolerate nanoparticle exposures. One limitation in comparing nanotoxicological data sets can be linked to a lack of harmonization and standardization of cell-based assays, where a) different cultivation conditions such as air-liquid interface or submerged cultures, b) varying barrier maturity and c) diverse media substitutes have been used. The current comparative nanotoxicological study therefore aims at analyzing the toxic effects of nanomaterials on four human mucosa barrier models including nasal (RPMI2650), buccal (TR146), alveolar (A549), and bronchial (Calu-3) mucosal cell lines to better understand the modulating effects of tissue maturity, cultivation conditions and tissue type using standard Transwell cultivations at liquid-liquid and air-liquid interfaces. Overall, cell size, confluency, tight junction localization, and cell viability as well as barrier formation using 50% and 100% confluency was monitored using trans-epithelial-electrical resistance (TEER) measurements and Presto Blue assays of immature (e.g. 5 days) and mature (e.g. 22 days) cultures in the presence and absence of corticosteroids such as hydrocortisone. Results of our study show that cellular responses to increasing nanoparticle exposures are highly cell type specific, where bronchial mucosal cell barriers models cultivated under ALI conditions showed less tolerance to acute ZnO nanoparticle exposures. Additionally, stronger toxicities are found using early mucosa barriers compared to later barrier models being maturated under air-liquid cultivation conditions.

Current clinical treatment options for symptomatic, partial-thickness rotator cuff tear (sPTRCT) offer only limited potential for true tissue healing and improvement of clinical results. In animal models, injections of adult stem cells isolated from adipose tissue into tendon injuries evidenced histological regeneration of tendon tissue. However, it is unclear whether such beneficial effects could also be observed in a human tendon treated with fresh, uncultured, autologous, adipose derived regenerative cells (UA-ADRCs). A specific challenge in this regard is that UA-ADRCs cannot be labeled and, thus, not unequivocally identified in the host tissue. Therefore, histological regeneration of injured human tendons after injection of UA-ADRCs must be assessed using comprehensive, immunohistochemical and microscopic analysis of biopsies taken from the treated tendon a few weeks after injection of UA-ADRCs.

Purpose: To meet the challenges of the precision medicine era, quality assessment of shared sarcoma care becomes pivotal. The MDT approach is the most important parameter for succesfull outcome. Because of all MDTs disciplines surgery is the key step to render sarcoma patients disease free, defining the spectrum of a sarcoma surgeon is critical. To the best of the authors knowledge, a comprehensive interoperable digital platform to assess the scope of sarcoma surgery and the experience of a sarcoma surgeon in its full complexity is lacking. Methods: A web-based real-world data (RWD) registry on sarcoma surgery has been created to assess the clinical exposure, tumor characteristics, and surgical settings and techniques applied for both resections and reconstructions of sarcomas and thereby the surgical exposure of an individual surgeon over time. Results: During 10 years, there were 723 sarcoma board/MDT meetings discussing 3130 patients. A total of 1094 patients underwent 1250 surgical interventions on mesenchymal tumors by one single sarcoma surgeon. These included 615 deep soft tissue tumors (197 benign, 102 intermediate, 281 malignant, 27 simulator, 7 metastasis, 1 blood), 116 superficial soft tissue tumors (45 benign, 12 intermediate, 40 malignant, 18 simulator, 1 blood) and 519 bone tumors (129 benign, 112 intermediate, 182 malignant, 18 simulator, 46 metastasis, 14 blood and 18 sequelae of 1st treatment). Detailed types of resections and reconstructions were analyzed. Conclusion: A web-based RWD sarcoma surgeon registry with transparent real-time descriptive analytics is feasible and enables large scale definition of the surgical complexity and ultimately quality of sarcoma care.

We synthesized iron(II)-triazole spin crossover compounds of the type [Fe(atrz)3]X2 and incorporated and deposited them on electrospun polymer nanofibers. In view of possible applications, we chose iron(II)-triazole-complexes that are known to exhibit spin crossover close to ambient temperature. Therefore we used the complexes [Fe(atrz)3]Cl2 and [Fe(atrz)3](2ns)2 (2ns = 2Naphthalenesulfonate) and analyzed them with IR-, UV/Vis and Mossbauer spectroscopy and with a SQUID magnetometer. The synthesized complexes were then in one attempt deposited on fibers of polymethylmethacrylate (PMMA) and in another attempt incorporated into core-shell like PMMA fiber structures. This was done via two different electrospinning methods. Deposition was performed by uniaxial electrospinning and incorporation was performed by coaxial electrospinning. The obtained polymer-complex-composites were then further investitgated by the same methods as the pure complexes as well as by SEM pictures and EDX measurements. The analysis by UV/Vis spectroscopy, Mössbauer spectroscopy and temperature-depended magnetic measurements with the SQUID magnetometer showed that the spin crossover properties were maintained and were not changed after the electrospinning processes and that the complexes were not harmed during the procedure.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

Proximal tubular epithelial cells (PTEC) are constantly exposed to potentially toxic metabolites and xenobiotics. The regenerative potential of the kidney enables the replacement of damaged cells either via the differentiation of stem cells or the regain of proliferative properties of the PTEC. Nevertheless, it is known that renal function declines, suggesting that the deteriorated cells are not replaced by fully functional cells. To understand the possible causes of this loss of kidney cell function, it would be beneficial to understand the role of toxins during the regeneration process. Therefore, we investigated the sensitivity and function of human induced pluripotent stem cells (hiPSC), hiPSC differentiating, and hiPSC differentiated into proximal tubular epithelial-like cells (PTELC) to known nephrotoxins. hiPSC were differentiated into PTELC, exhibiting a similar morphology to PTEC, expressing prototypical PTEC markers and performing albumin endocytosis. When treated with two nephrotoxins, hiPSC and differentiating hiPSC were more sensitive to cisplatin than differentiated PTELC, whereas all stages were equally sensitive to cyclosporin A. Both toxins also had an inhibitory effect on albumin uptake. Our results suggest a high sensitivity of differentiating cells towards toxins, which could have an unfavorable effect on regenerative processes. To study this, our model of hiPSC differentiating into PTELC appears suitable.

(1) Background: This work aimed to conduct the first comparative study providing long-term data about patient reported outcome measures as well as donor-site scar assessment and aesthetic evaluation of the reconstructed breasts in patients with DIEP versus PAP flap breast reconstruction. (2) Methods: This prospective, single-center, matched cohort study included a total of 36 patients after DIEP and PAP flap breast reconstruction. Evaluation was done using the Breast-Q and POSAS questionnaire as well as the Breast Aesthetic Scale for cosmetic analysis by four plastic surgeons. (3) Results: Post-operative Breast-Q evaluation revealed no significant differences between both patient groups for the categories physical well-being donor-site, physical well-being breast and satisfaction with the breast. Scar evaluation of the donor-site region showed equivalent results for the thigh and the abdomen concerning the overall opinion of patients and observers. There was no significant difference between both methods of reconstruction for all aspects of breast aesthetics. (4) Conclusions: Similar results of donor-site morbidity, scar quality and aesthetic outcome of the breast in both the DIEP and PAP patient group have been demonstrated. Hence, in cases suitable for both types of reconstruction, the decision can be based on factors such as patients’ lifestyle, leisure activities and preferences.

Hereditary Parkinson’s disease (PD) can be triggered by an autosomal dominant overdose of alpha-Synuclein (SNCA) as stressor or the autosomal recessive deficiency of PINK1 Serine/Threonine-phosphorylation activity as stress-response. We demonstrated the combination of PINK1-knockout with overexpression of SNCAA53T in double mutant (DM) mice to exacerbate locomotor deficits and to reduce lifespan. To survey posttranslational modifications of proteins underlying the pathology, brain hemispheres of old DM mice underwent quantitative label-free global proteomic mass spectrometry, focused on Ser/Thr-phosphorylations. As exceptionally strong effect, we detected >300-fold reductions of phosphoThr1928 in MAP1B, a microtubule-associated protein, and a similar reduction of phosphoSer3781 in ANK2, an interactor of microtubules. MAP1B depletion is known to trigger perturbations of microtubular mitochondria trafficking, neurite extension and synaptic function, so it was noteworthy that relevantly decreased phosphorylation was detected also for other microtubule and microfilament factors, namely MAP2S1801, MARK1S394, MAP1AT1794, KIF1AS1537, 4.1NS541, 4.1GS86 and ADD2S528. While the MAP1B heavy chain supports regeneration and growth cones, its light-chain assists DAPK1-mediated autophagy. Interestingly, relevant phosphorylation decreases of DAPK2S299, VPS13DS2429 and VPS13CS2480 in the DM brain affected regulators of autophagy, which are implicated in PD. Overall, significant downregulations were enriched for PFAM C2 domains, other kinases, and synaptic transmission factors upon automated bioinformatics, while upregulations were not enriched for selective motifs or pathways. Validation experiments confirmed the change of LC3 processing as reflection of excessive autophagy in DM brain, and dependence of ANK2/MAP1B expression on PINK1 levels. Our new data provide independent confirmation in a mouse model with combined PARK1/PARK4/PARK6 pathology that MAP1B/ANK2 phosphorylation events are implicated in Parkinsonian neurodegeneration. These findings expand on previous observations in D. melanogaster that the MAP1B ortholog futsch in the presynapse is a primary target of the PARK8 protein LRRK2, and on a report that MAP1B is a component of the pathological Lewy body aggregates in PD patient brains. Similarly, ANK2 gene locus variants are associated with the risk of PD, ANK2 interacts with PINK1/Parkin-target proteins such as MIRO1 or ATP1A2, and ANK2-derived peptides are potent inhibitors of autophagy.

Generating long-lived mucosal and systemic antibodies through respiratory immunization with protective antigens encapsulated in nanoscale biodegradable particles could potentially decrease or eliminate the incidence of many infectious diseases but requires incorporation of a suitable mucosal immunostimulant. We previously found that respiratory immunization with a model protein antigen (LPS-free OVA) encapsulated in PLGA 50:50 nanoparticles (~380 nm diameter) surface modified with complement peptide-derived immunostimulant 02 (CPDI-02; formerly EP67) through 2kDa PEG linkers increases mucosal and systemic OVA-specific memory T-cells with long-lived surface phenotypes in young, naïve female C57BL/6 mice. Here, we determined if respiratory immunization with LPS-free OVA encapsulated in similar PLGA 50:50 microparticles (~1 μm diameter) surface modified with CPDI-02 (CPDI-02-MP) increases long-term OVA-specific mucosal and systemic antibodies. We found that, compared to MP surface modified with inactive, scrambled scCPDI-02 (scCPDI-02-MP), intranasal administration of CPDI-02-MP in 50 μL sterile PBS greatly increased titers of short-term (14 days post-immunization) and long-term (90 days post-immunization) antibodies against encapsulated LPS-free OVA in nasal lavage fluids, bronchoalveolar lavage fluids, and sera of young, naïve female C57BL/6 mice. Thus, surface modification of biodegradable microparticles with CPDI-02 is likely to increase long-term mucosal and systemic antibodies against encapsulated protein antigen after respiratory and possibly other routes of mucosal immunization.

A large variety of fermentation products are used in food and feed production, but also in other industries, and many of these products are produced with genetically modified microorganisms (GMMs). In food and feed production, prominent examples are amino acids, vitamins, food and feed enzymes, colorants, non-caloric sweeteners and human milk oligosaccharides. From a regulatory perspective, fermentation products are typically produced under containment. This means that premises, equipment and work processes need to be designed to prevent or at least minimize release of GMMs into the environment. The fermentation products themselves should not contain any live cells of the GMM. Over the past years, there have been concerning developments, particularly in the European Union, stipulating that also absence of recombinant DNA might be interpreted as a regulatory requirement for fermentation products produced with GMMs. In this paper, we (i) attempt to place these developments into the historical context, (ii) sketch the potential negative repercussions for the food and feed industries, (iii) elaborate on the safety of recombinant DNA, and (iv) postulate that recombinant DNA should remain an integral part of the safety assessment of fermentation products but should not be misconstrued as a criterion for regulatory classification of products of biotechnology.

The separation of microparticles with respect to different properties such as size and material is a research field of great interest. Dielectrophoresis, a phenomenon which is capable of addressing multiple particle properties at once, can be used to perform a chromatographic separation. However, the selectivity of current dielectrophoretic particle chromatography (DPC) techniques is limited. Here we show a new approach for DPC based on differences in the dielectrophoretic mobilities and the crossover frequencies of polystyrene particles. Both differences are addressed by modulating the frequency of the electric field to generate positive and negative dielectrophoretic movement to achieve multiple trap and release cycles of the particles. A chromatographic separation of different particle sizes revealed a voltage dependency of this method. Additionally, we showed the frequency bandwidth influence on separation using one example. The DPC method developed was tested with model particles but offers possibilities to separate a broad range of plastic and metal microparticles or cells and to overcome currently existing limitations in selectivity.

This paper discusses wind tunnel test results aimed at advancing active flow control technology to increase the aerodynamic efficiency of an aircraft during take-off. A model of the outer section of a representative civil airliner wing was equipped with two-stage fluidic actuators between the slat edge and wing tip, where mechanical high-lift devices fail to integrate. The experiments were conducted at a nominal take-off Mach number of M = 0.2. At this incidence velocity, separation on the wing section, accompanied by increased drag, is triggered by the strong slat edge vortex at high angles of attack. On the basis of global force measurements and local static pressure data, the effect of pulsed blowing on the complex flow is evaluated, considering various momentum coefficients and spanwise distributions of the actuation effort. It is shown that through local intensification of forcing, a momentum coefficient of less than c_μ = 0.6% suffices to offset the stall by 2.4°, increase the maximum lift by more than 10%, and reduce the drag by 37% compared to the uncontrolled flow.

Purpose: Myelodysplastic syndromes (MDS) are caused by a stem cell failure, but the relationship between immune dysregulation and the course of disease has not yet been analyzed in detail. Experimental design: To get insights into the pathophysiologic and clinical relevance of the histotopography of immune cell subpopulations in this process, the immune cell infiltrate with focus on its spatial distribution was determined by multispectral imaging (MSI) in 147 bone marrow biopsies from MDS or secondary acute myeloid leukemia (sAML) patients and healthy controls (HC). In addition, the data were correlated to genetic alterations and clinical features of these patients including therapy response. Results: A high inter-tumoral heterogeneity in the frequency and spatial distribution of CD3⁺CD8⁺, CD3⁺CD8^-, CD3⁺FOXP3⁺ T cell subsets, MUM1p⁺CD3^- post-germinal B/plasma cells and CD34⁺ blasts was found in MDS and sAML samples. In HC only few B cells/plasma cells, but no T cell subpopulations were detected in the proximity to CD34⁺ blasts. In contrast, the frequency of these lymphocytes was increased in proximity to CD34⁺ blasts in both MDS and sAML independent of the karyotype, genetic alterations frequently detected in MDS, clinical risk stratification systems or treatment response to hypomethylating agents. Furthermore, an increased frequency of CD3⁺CD8⁺ T cells and MUM1p⁺ CD3^- B cells was found in responders to epigenetic drugs. Conclusions: Thus, we conclude that (i) T cell subsets do not belong to the normal stem cell niche, (ii) the presence of T and B cell subpopulations not directly affect the course of MDS, (iii) lymphocytes in the proximity to CD34⁺ blasts might indicate defective stem cell properties and (iv) the number of lymphocytes is a predictor of therapy response to hypomethylating agents.

A key in controlling the SARS-CoV-2 pandemic is the assessment of the immune status of the population. We explored the utility of SARS-CoV-2 virus-like particles (VLPs) as antigens to detect specific humoral immune reactions in an enzyme-linked immunosorbent assay (ELISA). For this purpose, SARS-CoV-2 VLPs were produced from an engineered cell line and characterized by western blot, ELISA and nanoparticle tracking analysis. Subsequently, we collected 42 serum samples from before the pandemic (2014), 89 samples from healthy-, and 38 samples from vaccinated subjects. Seventeen samples were collected less than three weeks after infection, and 44 samples more than three weeks after infection. All serum samples were characterized for their reactivity with VLPs and the SARS-CoV-2 N- and S-protein. Finally, we compared the performance of the VLP-based ELISA with a certified in vitro diagnostic device (IVD). In the applied set of samples, we determined a sensitivity of 95.5 % and a specificity of 100 % for the certified IVD. There were 7 samples with an uncertain outcome. Our VLP-ELISA showed superior performance with a sensitivity of 97.5 %, a specificity of 100 %, and only 3 uncertain outcomes. This result warrants further research to develop a certified IVD based on SARS-CoV-2 VLPs as an antigen.

A scientific consensus is emerging on the benefits of dc distribution in medium voltage power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage dc operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of dc versus ac, and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under ac and dc conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20\,kV and 0 to 0.1\,Hz, respectively. The change in PD activity with void evolution is explored.

The CAALA (Complex Augmentation of ALA) regimen was developed with the goal of redressing some of the weaknesses of 5-aminolevulinic acid (5-ALA) use in glioblastoma treatment as it now stands. 5-ALA is approved for use prior to glioblastoma surgery to better demarcate tumor from brain tissue. 5-ALA is also used in intraoperative photodynamic treatment of glioblastoma by virtue of uptake of 5-ALA and its selective conversion to protoporphyrin IX in glioblastoma cells. Protoporphyrin IX becomes cytotoxic after exposure to 410 nm or 635 nm light. CAALA uses four currently marketed drugs - the antibiotic ciprofloxacin, the iron chelator deferiprone, the antimetabolite 5-FU, and the xanthine oxidase inhibitor febuxostat - that all have evidence of ability to both increase 5-ALA mediated intraoperative glioblastoma demarcation and photodynamic cytotoxicity of in situ glioblastoma cells. Data from testing the full CAALA on living minipigs xenotransplanted with human glioblastoma cells will determine safety and potential for benefit in advancing CAALA to a clinical trial.

Serine peptidase CLPP is conserved among bacteria, chloroplasts, and mitochondria. In humans and mice, its loss causes Perrault syndrome with growth deficit, infertility, deafness, and ataxia. In the filamentous fungus Podospora anserina, CLPP-loss leads to longevity. CLPP substrates are selected by CLPX, an AAA+ unfoldase. CLPX is known to target delta-amino-levulinic-acid synthase (ALAS) to promote pyridoxal-phosphate (PLP) binding. CLPX may influence cofactor association with other enzymes. Here, the evaluation of P. anserina metabolomics highlighted arginine/histidine reduction. In Mus musculus cerebellum, reductions of Arginine/Histidine and Citrulline occurred with concomitant accumulation of heme-precursor protoporphyrin-IX. This suggests that increased biosynthesis of 5-carbon (C5) chain deltaALA consumes not only C4 succinyl-CoA with C1 glycine but also specific C5 delta amino-acids. As responsible enzymes for these converse effects, elevated abundance of CLPX and ALAS is paralleled by elevation of OAT (PLP-dependent, ornithine-delta-aminotransferase). Possibly as consequence of altered C1 metabolism, CLPP-null cells in P. anserina proteome profiles showed strong accumulation of a methyltransferase and two mitoribosomal large subunit factors. Reduced Histidine levels may explain previously observed metal interaction problems. As main nitrogen-storing metabolite, deficient Arginine would affect the urea cycle and polyamine synthesis. Supplementation of Arginine and Histidine might rescue growth deficits of CLPP-mutant patients.

We discuss two methods to detect the presence and location of a person in a small-scale room and compare the performances. The first method is Direct Intersection, which determines a coordinate point based on the intersection of spheroids defined by observed distances of high-intensity reverberations. The second method, Sonogram analysis, overlays all channel’s room impulse responses to generate an intensity map for the observed environment. We demonstrate that the former method has lower computation complexity and higher accuracy for small numbers of channels, while the latter performs more robustly.

(1) Background: Deep hypothermic circulatory arrest (DHCA) with selective antegrade cerebral perfusion (ACP) is an established cerebral protection technique for the conduction of complex surgical procedures involving the aortic arch. It is controversial if the duration of DHCA is associated with adverse outcome in patients with acute type A aortic dissection (AAAD). Our goal was to investigate whether DHCA time was associated with surgical outcome in patients undergoing a surgical treatment of AAAD. (2) Methods: 410 Patients were divided into two groups concerning the DHCA time less than 60 minutes and equal or longer than 60 minutes. (3) Results: Patients with longer DHCA time were significantly younger (p=0.001). Intraoperatively, complex procedures with aortic arch surgery were more common in patients with longer DHCA time (p&lt;0.001). Accordingly, cardiopulmonary bypass (p&lt;0.001), cross-clamping (p&lt;0.001) and DHCA times (p&lt;0.001) were significantly longer in this group. Postoperatively, only the duration of mechanical ventilation (p&lt;0.001) and the rate of tracheotomy were significantly higher in these patients. 30-day mortality was satisfactory for both groups (p=0.746). (4) Conclusions: Our results showed that improvements in perioperative management including ACP allow a successful performance of surgical treatment of AAAD under DHCA with duration of even longer than 60 minutes.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

Ca Mau Peninsula (CMP), the southernmost region of the Mekong Delta, is facing a severe loss of land and freshwater. Particularly, the groundwater resources in the complex multilayered aquifer system of CMP are subject to salinization processes, which are not yet fully understood. In this study, an existing groundwater flow model for the CMP was enhanced to a density-dependent transient transport model using the FEFLOW software package, which is based on the finite element method. The study focuses on simulating groundwater salinity in order to better understand the dynamics of groundwater salinization and potential saltwater intrusion pathways in the study area. Time series of Total Dissolved Solids (TDS) concentrations at observation wells were used to compare simulated and observed salinity data in different aquifers. The model allows a multi-factorial evaluation of the spatial groundwater salinity and could also confirm significant inter-annual variability, particularly in the case of shallow aquifers due to the influence of tides and seasonal rainy/dry seasons. Using sensitivity analysis, leakage from upper saline aquifers into lower freshwater aquifers through natural hydrogeological windows and poorly sealed boreholes was identified as a potential major cause for groundwater salinization occurring in the region. The results obtained can serve as an important basis for developing decision-making tools to promote the sustainable use of water resources on the CMP in the future.

Partially automated driving functions (SAE Level 2) can control a vehicle's longitudinal and lateral movements. However, taking over the driving task involves automation risks that the driver must manage. In severe accidents, the driver's ability to avoid a collision must be assessed, considering their expected reaction behavior. The primary goal of this study is to generate essential data on driver reaction behavior in case of malfunctions in partially automated driving functions for use in legal affairs. A simulator study with two scenarios involving 32 subjects was conducted for this purpose. The first scenario investigated driver reactions to system limitations during cornering. The second scenario examined driver responses to phantom braking caused by the AEBS. As a result, the first scenario shows that none of the subjects could control the situation safely. Due to partial automation, we could also identify a new part of the reaction time, the hands-on time, which leads to increased steering reaction times of 1.18 to 1.74 seconds. In the second scenario, we found that 25 of the 32 subjects could not override the phantom braking by pressing the accelerator pedal, although 16 subjects were informed about the system analog to the actual vehicle manuals. Overall, the study suggests that the current legal perspective on vehicle control and the expected driver reaction behavior for accident avoidance should be reconsidered.