In the present research, we will develop some integral inequalities of Hermite Hadamard type for differentiable η-convex function. Moreover, our results include several new and known results as special cases.

The Chiltan Formation is a potential hydrocarbon-producing reservoir in the Indus Basin, Pakistan. However, its diagenetic alterations and heterogeneous behavior lead to significant challenges in accurately characterizing the reservoir and production performance. This manuscript aims to utilize Chiltan Limestone core samples to conduct a detailed analysis of the diagenetic impacts on reservoir quality. The formation evaluation was carried out through thin section analysis, SEM-EDS and FTIR investigation, as well as plug porosity and permeability measurements under different stress conditions. In results, Petrography revealed three microfacies with distinct diagenetic features and micro-nano fossil assemblages, including intraclasts, pelloids, bioclasts, and stylolites. Diagenesis has a significant impact on petrophysical properties, leading to increased reservoir heterogeneity. The specified depositional environment exposed the alteration of the Chiltan formation during distinct diagenetic phases in marine, meteoric, and burial settings. Pore morphology and mineralogy reveals complex micro-pore structure with various carbonate mineral phases and cement types in the formation samples. The average porosity and permeability of the core samples were found to be 3.4% and 0.449 mD respectively, indicating poor reservoir quality. Stress sensitivity was determined using Klinkenberg corrected permeability, which indicated a reduction in measured and absolute permeability due to increasing confining stress, further reducing the pore throat structure of the formation. In conclusion, the Chiltan formation possesses intricate reservoir heterogeneity and varied micro-pore structure caused by diagenesis and depositional settings. The formation is classified as a low-quality reservoir due to its non-uniform pore geometry, which exhibits low petrophysical properties resulting from overburden stress. The results of this study provide solid foundation in reservoir characterization and quality assessment which has implications for exploring and exploitation of indigenous resources.

A highly sensitive strain sensor based on tunable cascaded Fabry-Perot interferometers (FPIs) is proposed and experimentally demonstrated. Cascaded FPIs consist of a sensing FPI and a reference FPI which effectively generate the Vernier Effect (VE). The sensing FPI comprises a hollow core fiber (HCF) segment sandwiched between single-mode fibers (SMFs), and the reference FPI consists of a tunable air reflector, which is constituted by a computer programable fiber holding block to adjust the desired cavity length. Simulation results predict the dispersion characteristics of modes carried by HCF. The sensor’s parameters are designed corresponding to a narrow bandwidth range, i.e., 1530 nm to 1610 nm. Experimental results demonstrate that the proposed sensor exhibits optimum strain sensitivity of 23.9 pm/με in the range of 0 to 3000 με which is 13.73 times higher than the single sensing FPI strain sensitivity of 1.74 pm/με. The strain sensitivity of the sensor can be further enhanced by extending the source bandwidth. The proposed sensor exhibits ultra-low temperature sensitivity of 0.49 pm/°C in the wider temperature range of 25 °C to 135 °C, providing good isolation for eliminating cross-talk between strain and temperature. The sensor is very robust, cost-effective, easy to manufacture, repeatable, and shows a highly linear and stable response in the wider range of axial strain. Based on the sensor’s performance, it may suit plenty of practical applications in the real sensing world

We studied the influence of lava meal, zeolite and top layer of sandy soil as bedding additives on gaseous C and N losses from a sloping-floor barn of naturally ventilated animal housing. We selected four barn units where eight young bulls’ group was reared in each barn. Chopped straw of wheat and barley applied daily at the rate of 5 kg per livestock unit (LU) in bedding areas where one LU consisted of 500 kg body mass of live bulls. Zeolite, lava meal and sandy soil (18% clay + silt) applied in barn at the rate of 10, 20 and 30% of straw dose, respectively. Static flux chamber was used to measure gases emissions from the barn unit and mass balance calculation was used to calculate straw manure total N (TN) losses during housing phase. On an average, all bedding additives decreased 85% of the NH₃ emission compared to control; however, they did not influence CH₄ emission. Zeolite decreased CO₂ (35%) and N₂O (37%) emission rates. Subsequently, lava meal, sandy soil and zeolite decreased 23, 37, and 50% of TN losses from barn manure, respectively. Overall, measured N emissions through NH₃-N and N₂O-N from the barns was 11% of calculated TN losses while remainder 89% was most probably attributed to di-nitrogen (N₂), a harmless gas. Hence, in straw-based cattle housings, zeolite could be a promising additive for reduction of CO₂, N₂O and NH₃ emissions and sandy soil can be considered as cheap and readily available resource for reducing NH₃ emission.

This paper presents a symmetrical topology for the design of solid-state transformer, made up of power switching converters, to replace conventional bulky transformers. The proposed circuitry not only reduces the overall size but also provides power flow control with the ability to be interfaced with renewable energy resources (RESs) to fulfill the future grid requirements at consumer end. Solid state transformer provides bidirectional power flow with variable voltage and frequency operation and has the ability to maintain unity power factor, and current total harmonic distortion (THD) for any type of load within defined limits of IEEE standard. Solid State Transformer offers much smaller size as compared to that of the conventional iron core transformer. MATLAB/Simulink platform is adopted to test the validity of the proposed circuit for different scenarios by providing the simulation results evaluated at 25 kHz switching frequency.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T₁ = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T₂ = 50 kg N ha^-1, T₃ = 100 kg N ha^-1 and T₄ = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T₅: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T₆: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T₇: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO₂ concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T₆ = Split N₁₀₀) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

The hydrocarbon generation potential of Chia Gara strata and their genetic link with produced oils from the Zagros basin are still not comprehensively investigated. Forty-seven rock samples from the Tithonian–Berriasian interval were subjected to geochemical analyses to infer organic matter enrichment, hydrocarbon potential, thermal maturity, and timing for hydrocarbon generation/expulsion and their implications regarding upcoming petroleum explorations in the Zagros basin. The results showed that the Chia Gara rock samples have fair to very-good generation potential, as confirmed by higher total organic carbon (TOC=0.68–3.95 wt%) and Rock-Eval (S1+S2=3.37–8.52 mg HC/g rock). The hydrogen index (HI=171–462) and Rock-Eval Tmax over 430 °C support the presence of Types II and mixed Types II/III kerogen. These results confirm the high generation potential of the Chia Gara Formation in the study region. 1D basin models of the KK–109 well show that over 55% of kerogens were converted into oil in the Cretaceous (77–67 Ma). Expulsion started from the Miocene until now (22–0 Ma), consistent with 0.71–0.80 of modeled Easy%Ro and 55–80 %TR. Consequently, this project confirms the potential oil expulsion from the Chia Gara Formation, which can be a resource for upcoming hydrocarbon investigation in the Zagros basin, Iraq.

This research paper is mainly aimed to elaborate the initial risk management and measures which government of Pakistan took towards Novel Corona Virus (COVID-2019). This initial response and planning was devised after the early outbreak of COVID-2019 in Wuhan, China in early time of January 2020. Pakistan devised a comprehensive plan that not to evacuate their student from Wuhan, China. The government of Pakistan in compliance with the National Institute of Health (NIH) devised and documented comprehensive plans such as the flight operations postponed related to Umerah pilgrims, which were intended to go to sacred places of KSA (The Kingdom of Saudi Arabia). The process of visa, immigration policy totally changed and the government of Pakistan notified it officially that, no new visas of visit, student, and business would be issued in due course of uncertainty due to COVID-2019. The government of Pakistan also announced medical emergency and notified through the country’s provinces the process of testing and treatment of COVID-2019. The government of Pakistan also allocated funds for medical supplies and named out the particular country’s best laboratories. The government of Pakistan also locked down all the cities with the emergency announcement that people should stay inside the home in quarantine or self-isolation. NIH (The National Institute of Health) played a vital role in executing the planning to cope with COVID – 2019). The National Institute of Health responded as “The Centre for Disease Control”. In aid to the government, the national army of Pakistan responded in a proactive manner towards planed execution. The medical corps of Pakistan army dedicated themselves to treat the suspected patients of COVID – 2019. Due to plans, policies being documented, implemented in such a way productive way that from February 28, 2020 to till date there is not much critical situation and issues are not present. There are much productive results as there is not much boom in a rise of COVID-2019 patients. This lockdown under the authority of the provinces resulted in fruitful outcomes. Background: On January 02, 2020, authorities of the People Republic of China elaborated that they have encountered with a novel type of infectious viral disease 2019. Later on January 12, the authorities from China elaborated the related sequence of Corona Virus diseases 2019 names as COVID – 2019. When COVID-2019 being identified in Wuhan, Hubei China, as an early response the Government of Pakistan in support of the National Institute of Health (Field Epidemiology & Disease Surveillance Division) published a health advisory about novel coronavirus. Methods: According to Global Health Security Index, Pakistan is ranked as 105th country among 195 countries in GHS index. Overall Score of Pakistan is 35.5. The score of Early Detection and Reporting for Epidemics of Potential International Concern is 41.7. A Graphical depiction of the COVID-19 cases placed until April 10, 2020 as well as a graph trend line of recovered as well as death rate is also depicted. According to the graphical facts of Government of Pakistan and World meters, the recovery rate of COVID-19 is about 98 percent and 2.1 percent death rate is reported against the total cases. Trend analysis with line graph was drawn based on available data from official dashboard web portal of the government of Pakistan and worldometers.info. Data figures were incorporated from March to August 18, 2020 in MS Excel and then subsequently deployed to draw trend analysis from managing risk to recovery. Results: The line graph showed a slowdown in the COVID-19 cases and high rate of recoveries from COVID-19 in Pakistan. On March 11, 2020, there were 20 confirmed cases of coronavirus reported in Pakistan. No death was recorded in very first seven days, on March 18, 2020 only two deaths were reported. On August 18, 2020, there were 272128 recoveries, 6201 deaths, total confirmed cases 290445, and total test were 2340072 in Pakistan. As a results, we can report that due to early measures taken by government of Pakistan no mass scale destruction in terms of death and cases been recorded in Pakistan. Conclusions: To till date, the government of Pakistan tried its level best to minimize the coronavirus cases as much as they can. However, the ending of the potential attack of an outbreak would depend upon the well organized and coordinated approach at all levels such as true directed decisions, fully preparedness, as well implementation and evaluation of continuous decisions. As the recovery rate of the cases is 98 percent and merely death rate is 2.1 percent, concluded that in future it would be a good sign to stop the potential outbreak. Also, lock down as well as precautionary measurement taken by the provincial governments resulted a decline number of COVID-19 cases in the country. Another good sign is that merely 4 percent population of Pakistan is of more than 60 years of old it can be concluded that there are less chances of mass death due to outbreak of COVID-19.

The simultaneous evaluation of heat/mass transference procures momentous significance in the polymer industry and engineering activities. Extensive utilization of such aspects includes propylene flares, heat exchangers, energy transfiguration in chilling towers, and amputation of post fortuitous heat in nuclear reactors. Owing to such prospective demands, we interpreted the Jeffrey liquid reactive flow under non-linear convection. We scrutinized the transference of heat/mass under generalized Fourier-Fick relations. Thermal conductivity depends on temperature while mass diffusivity is dependent on concentration. Besides, heat source along with first-order chemical reaction aspects are accounted for. Relevant transformations are exerted to achieve non-linear differential systems that are solved through the homotopy scheme. Influences of divers factors are exhibited via graphical benchmark.

The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr₂₃C₆ .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

During the casting in a warmer tropical temperature, a setting time delay is required to maintain the workability of the concrete, commonly achieved by the addition of admixtures i.e. silica fume (SF), fly ash (FA), and Plastrocrete®. However, high sugar content Coca-Cola in niche conditions is proposed as an ingredient for delaying concrete setting time in combination with conventional admixtures. This research aims to compare the setting time of admixtures from Coca-Cola and Plastocrete® RT6 plus in concrete mixing with control data of concrete mixed with SF or FA. The second aim is to measure the compression strengths between combinations of Coca-Cola and Plastocrete® RT6 plus. Concretes were produced with admixtures of SF, FA, Plastocrete® RT6plus, or Coca-Cola. The concrete used to control was f'c20 and f'c 25, while other concrete mixes were produced with the addition of Coca-Cola at 0.15% from the weight of cement at variation of moisture treatments. The first method to produce concrete (f'c20+Plas0.23%+Cola0.15% and f'c25+Plas0.23%+Cola0.15%) did not employ water reduction. The second concrete productions (f'c25+Plas0.46%+Cola0.15% and f'c25+Plas0.46%+Cola0.15%) reduced the addition of water at 8.8% (v/w). The first concrete production method had a setting time 44% longer than control. The reduced water concrete in the second productions had a setting time 34% longer than control. Meanwhile, the Plastocrete® RT6 Plus admixture with the reduced water delayed the concrete setting time by 26% longer than control. The delayed setting time of Plastocrete® RT6 Plus admixture with reduction of water was shorter than in the treatment with Coca-Cola. The combination of the addition of Coca-Cola with Plastocrete® RT6 plus by reducing the amount of adding Coca-Cola to 0.10% with Plastocrete® RT6 plus can delay concrete setting time by 51% longer than normal concrete and increase concrete compressive strength by 13% higher than normal concrete. Mixing Coca-Cola with Plastocrete® RT6 plus not only provided an optimal delay effect on setting time but also significantly increase the compressive strength that was desired during the casting in warm tropical weather applied in building construction of Mulawarman University, Samarinda, Indonesia.

Fresh water is an increasingly scarce resource in both urban and rural developments. As a response to this challenge, non-potable water reuse is on the rise. This research explored a potential off-grid system for water purification, consisting of a staircase wetland with terracotta pot plants working as a filter for greywater. The study further investigated the physicochemical properties of the greywater and the soil before and after the wetland purification. Results showed that the filtered water satisfied all requirements for water reuse, e.g., pH, turbidity, and total coliforms. The research then uniquely investigated the effect of greywater on the soil biodiversity and soil biomass using soil DNA extraction and the tea bag index testing method. The filtered greywater absorbed by soil decomposed the soil faster and stabilized it better compared to tap water-absorbed soil or unfiltered greywater. The DNA generation sequencing revealed no significant differences in alpha diversity between control and treatment samples. The beta diversity differences were significant. This nature-based solution can lead to reduced load on the sewage system, resulting in less wastewater generation.

In this study, our primary objective was to analyze the tradeoff between accuracy and complexity in machine learning models, with a specific focus on the impact of reducing complexity and entropy on the production of landslide susceptibility maps. We aimed to investigate how simplifying the model and reducing entropy can affect the capture of complex patterns in the susceptibility maps. To achieve this, we conducted a comprehensive evaluation of various machine-learning algorithms for classification tasks. We compared the performance of these algorithms in terms of accuracy and complexity, considering both "before" and "after" scenarios of dimensionality reduction using Principal Component Analysis (PCA). Our findings revealed that reducing complexity and lowering entropy can lead to an increase in model accuracy. However, we also observed that this reduction in complexity comes at the cost of losing important complex patterns in the produced landslide susceptibility maps. By simplifying the model and reducing entropy, certain intricate relationships and uncertain patterns may be overlooked, resulting in a loss of information and potentially compromising the accuracy of the susceptibility maps. The analysis encompassed a diverse range of machine learning algorithms, including Random Forest (RF), Extra Trees (EXT), XGboost, LightGBM, Catboost, Naive Bayes (NB), K-Nearest Neighbors (KNN), Gradient Boosting Machine (GBM), and Decision Trees (DT). Each algorithm was evaluated for its strengths and limitations, considering the tradeoff between accuracy and complexity. Before dimensionality reduction, the algorithms demonstrated promising results, with RF exhibiting excellent AUC/ROC scores and average accuracy. However, computational costs were noted as a potential drawback for RF, especially when dealing with large datasets. EXT showcased robust performance and good accuracy, while XGboost demonstrated its ability to handle complex relationships within large datasets, albeit requiring careful hyperparameter tuning. The efficiency and scalability of LightGBM made it a suitable choice for large datasets, although it displayed sensitivity to class imbalance. Catboost excelled in handling categorical features, but longer training times were observed for larger datasets. NB showcased simplicity and computational efficiency but assumed independence among features. KNN, known for its capability to capture local patterns and spatial relationships, was found to be sensitive to the choice of distance metric. GBM, while capturing complex relationships effectively, was prone to overfitting without proper regularization. DT, with its interpretability and ease of understanding, faced limitations in terms of overfitting and limited generalization. After dimensionality reduction, certain algorithms exhibited improvements in their AUC/ROC scores and average accuracy, including RF, EXT, XGboost, and LightGBM. However, for a few algorithms, such as NB and DT, a decrease in performance was observed. This study provides valuable insights into the performance characteristics, strengths, and limitations of various machine learning algorithms in classification tasks. Researchers and practitioners can utilize these findings to make informed decisions when selecting algorithms for their specific datasets and requirements. We also aim to identify the potential factors contributing to the high accuracy rates obtained from these ensembled algorithms and explore possible shortcomings of non-ensembled algorithms that may result in lower accuracy rates. By conducting a comprehensive analysis of these algorithms, we seek to provide valuable insights into the benefits and limitations of ensembled approaches for landslide susceptibility mapping. Our study sheds light on the challenges faced when balancing accuracy and complexity in machine learning models for landslide susceptibility mapping. It emphasizes the importance of carefully considering the level of complexity and entropy reduction in relation to the specific patterns and uncertainties present in the data. By providing insights into this tradeoff, our research aims to assist researchers and practitioners in making informed decisions regarding model complexity and entropy reduction, ultimately improving the quality and interpretability of landslide susceptibility maps.

Obesity is characterized by surplus buildup of body lipids primarily in adipose tissue. Prevalence and incidence of obesity are ascending persistently at an alarming rate. Unusual eating behaviors like compulsion to eat (food addiction) and excessive consumption are the premier contributors to obesity. Both are under influence of a variety of stimuli, mainly being stress, emotions, dietary restrictions, sweetness, hyperpalatability, neural pathways, hormonal imbalance and genetics. This review summarizes the potential driving factors behind overeating and food addiction for understanding and exploring obesity linked novel agents and processes as an endeavor to advance treatment approaches. Obesity has been studied extensively throughout the world due to high incidence and association with several metabolic disorders including cardiovascular disorders. The food addition has considered one of potential key factor of obesity and excessive weight gain. Sedentary life style and availability of food also induce obesity.

The study is based on the notion that big data predictive analytics is important for developing strategic alliances performance of companies. this study investigates the relationship between big data predictive analytics, big data culture, and competitive strategies 'techniques were adopted, such as descriptive statistics, correlation,regression, etc. using SPSS and SmartPLS statistical software. Hypotheses were tested with bootstrapped analysis using SEM (through SmartPLS). The study developed a structural equation model by using the SEM analysis. The results of the SEM analysis suggested the hypothesized model of the study was valid. The results supported all the hypotheses of the study.Through empirical analysis, demonstrated the conclusion is that the big data predictive analytics has a positive and significant relationship with strategic alliance performance

Automation is at the core of modern industry. It aims to increase production rates, decrease production costs, and reduce human intervention in order to avoid human mistakes and time delays during manufacturing. On the other hand, human assistance is usually required to customize products and reconfigure control systems through a special process interface called Human Machine Interface (HMI). Machine Learning (ML) algorithms can effectively be used to resolve this tradeoff between full automation and human assistance. This paper provides an example of the industrial application of ML algorithms to help human operators save their mental effort and avoid time delays and unintended mistakes for the sake of high production rates. Based on real-time sensor measurements, several ML algorithms have been tried to classify paper rolls according to paper grammage in a white paper mill. The performance evaluation shows that the AdaBoost algorithm is the best ML algorithm for this application with classification accuracy (CA), precision, and recall of 97.1%. The generalization of the proposed approach for achieving a cost-effective mill construction by reducing the total number of the required physical sensors will be the subject of our future research.

Background: Renal cancers are among the top ten causes of cancer-specific mortality, of which the ccRCC subtype is responsible for most cases. The grading of ccRCC is important in determining tumour aggressiveness and clinical management. Objectives: The objectives of this research were to predict the WHO/ISUP grade of ccRCC pre-operatively and characterise the heterogeneity of tumour sub-regions using radiomics and ML models, including comparison with pre-operative biopsy-determined grading in a sub-group. Methods: Data were obtained from multiple institutions across two countries, including 391 patients with pathologically proven ccRCC. For analysis, the data were separated into four cohorts. Cohorts 1 and 2 included data from the respective institutions from the two countries, cohort 3 was the combined data from both cohort 1 and 2, and cohort 4 was a subset of cohort 1, for which both the biopsy and subsequent histology from resection (partial or total nephrectomy) were available. 3D image segmentation was carried out to derive a voxel of interest (VOI) mask. Radiomics features were then extracted from the contrast-enhanced images, and the data were normalised. The Pearson correlation coefficient and the XGBoost model were used to reduce the dimensionality of the features. Thereafter, 11 ML algorithms were implemented for the purpose of predicting the ccRCC grade and characterising the heterogeneity of sub-regions in the tumours. Results: For cohort 1, the 50% tumour core and 25% tumour periphery exhibited the best performance, with an average AUC of 77.9% and 78.6%, respectively. The 50% tumour core presented the highest performance in cohorts 2 and 3, with average AUC values of 87.6% and 76.9%, respectively. With the 25% periphery, cohort 4 showed AUC values of 95.0% and 80.0% for grade prediction when using internal and external validation, respectively, while biopsy histology had an AUC of 31.0% for the classification with the final grade of resection histology as a reference standard. The CatBoost classifier was the best for each of the four cohorts with an average AUC of 80.0%, 86.5%, 77.0% and 90.3% for cohorts 1, 2, 3 and 4 respectively. Conclusion: Radiomics signatures combined with ML have the potential to predict the WHO/ISUP grade of ccRCC with superior performance, when compared to pre-operative biopsy. Moreover, tumour sub-regions contain useful information that should be analysed independently when determining the tumour grade. Therefore, it is possible to distinguish the grade of ccRCC pre-operatively to improve patient care and management.

Enhancement of mechanical properties by using TiN/TiCN/TiC multilayer thin films deposited on commercially pure cast Titanium (CP-Ti), Ti6Al4V and silicon (Si) substrates via magnetron sputtering technique was investigated in this study. The structural, chemical and mechanical properties of the coatings were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), nanoindentation and scratch test. Results of the XRD analysis showed reflections corresponded to FCC (1 1 1) cubic and polycrystalline structure for TiN/TiCN/TiC films. XPS analysis revealed formation of titanium nitride, titanium carbonitride and titanium carbide in the coatings. According to SEM images, the coatings demonstrated dense cross-sectional morphology and columnar structure as well as good adhesion to the substrate with a thickness of 1.77 μm deposited on silicon (1 0 0). Scratch and nanoindentation test results showed the best mechanical behavior for the coated Ti6Al4V substrate material with the 19.96 GPa hardness and 25 N critical load values, because of its higher hardness and toughness of substrate in compared to Cp-Ti substrate.

Enhancement of mechanical properties by using TiN/TiCN/TiC multilayer thin films deposited on commercially pure cast Titanium (CP-Ti), Ti6Al4V and silicon (Si) substrates via magnetron sputtering technique was investigated in this study. The structural, chemical and mechanical properties of the coatings were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), nanoindentation and scratch test. Results of the XRD analysis showed reflections corresponded to FCC (1 1 1) cubic and polycrystalline structure for TiN/TiCN/TiC films. XPS analysis revealed formation of titanium nitride, titanium carbonitride and titanium carbide in the coatings. According to SEM images, the coatings demonstrated dense cross-sectional morphology and columnar structure as well as good adhesion to the substrate with a thickness of 1.77 μm deposited on silicon (1 0 0). Scratch and nanoindentation test results showed the best mechanical behavior for the coated Ti6Al4V substrate material with the 19.96 GPa hardness and 25 N critical load values, because of its higher hardness and toughness of substrate in compared to Cp-Ti substrate.

This paper aims to unify q-derivative/q-integral and h-derivative/h-integral in a single definition, this will be called q−h-derivative/q−h-integral. These notions are further extended on finite interval [a,b] in the form of left and right q−h-derivatives and q−h-integrals. Some inequalities are studied for q−h-integrals which are directly connected with well known results. In diverse fields of science and engineering the theory based on q-derivatives/q-integrals and h-derivatives/h-integrals can be unified by using the concept of q−h-derivative/q−h-integral.

Winter frost injury is a major limiting factor for olive cultivation in temperate regions. The response of olive shoots to freezing stress can be used for selecting resistant genotypes to freezing. The electrolyte leakage (EL) and tetrazolium tests (TZ) are commonly used to evaluate dead tissues in cold stress studies. The temperature-response curve of dead tissues to lethal temperature (LT) is measured with models to calculate LT50 and LT90. In this study, we evaluated the accuracy and efficiency of eighteen non-linear regression models (NLRs) in calculating LT50 and LT90 of freezing stress in different olive cultivars at various stages of dormancy. After evaluating the prediction performance of NLR models, it was found that only eight models were suitable for the purpose of this research out of the 18 models examined. The 2p-logistic and Gompertz models were selected for modeling EL and TZ, respectively. Our research findings indicate that the Roughani, Kawi, and Zard varieties of olive trees exhibit the best performance in cold weather conditions. Our findings provide valuable insights into selecting frost-resistant cultivars and designing effective strategies for cold acclimation in olive cultivation.

The importance of Muscovy ducks in industrial poultry production is growing; however, little is known about the physiology of their reproductive cycles. This study investigated the influence of male biostimulation on female ducks before the commencement of the laying phase. A total of 15 female Muscovites were kept in contact with a male duck until the point of laying, while 15 other females were kept without any contact with a male conspecific. Before reaching egg-laying maturity, the cloacae of 29 adult ducks were subjected to daily clinical assessments. The evaluations yielded four unique categories of outcomes, determined by assessing factors such as the degree of redness and protrusion of the mucous membrane, moisture level, and swelling of the cloacal sphincter muscle. In terms of biostimulation, the findings demonstrated that, on average, ducks in contact with males laid the first egg 16 days earlier than isolated ducks. Furthermore, there was no significant difference observed in the mean initial egg weight between both groups (p = 0.841). The changes in the cloacal morphology indicated significant morphological changes 25–26 days before laying. Efforts to improve Muscovy production and develop biotechnological techniques to modify the reproductive cycle will benefit from these advancements.

Utilization of medicine derived from plants has been documented in various traditional systems of medicines throughout the world for different diseases. Therefore, the current research work was carried out to evaluate the phytochemical and biological potential of Ficus carica L ethanolic leaf extract. For this purpose, physicochemical and phytochemical analysis, total phenolic and flavonoids contents was performed. Antioxidant potential was determined by FRAP, DPPH and H2O2 assay. Proteinase inhibition, heat induced hemolysis and BSA denaturation assay was carried out for inflammation. Antiglycation potential was assessed by fructosamine assay, Congo-red assay and estimation of free carbonyl groups. In-vivo antidiabetic, anti-obesity, effect on liver and kidney were investigated by high fat high sugar diet model. FTIR, HPLC and LCMS/MS analysis was performed to find out the compounds. Tablet based formulation was developed using wet granulation method and tested for physicochemical parameters. Results shows that total phenolic and flavonoids content was (333 mg GAE/g) and (123 mg RE/g) respectively, H2O2 assay shows 35.6% free radical inhibition potential, DPPH assay shows (IC50) inhibitory concentration at 0.58 mg/mL, and 88.769 µg/g Fe2SO4 solution FRAP values. Proteinase inhibition assay, Heat induced hemolysis and BSA-denaturation assay shows percentage inhibition of 28 ± 0.01, 55 ± 0.03 and 51.2 ± 0.05 respectively. In Antiglycation activity β-amyloid formation assay shows absorption of 0.017, Fructosamine assay shows inhibition of 19.4±0.06 and free carbonyl group estimation shows inhibition of 17.0±0.03. In in-vivo study FLE at (500 mg/kg) significantly decreased total bilirubin (p ≤ 0.001), decreased (p ≤ 0.05) alanine transferase, aspartate aminotransferase, alkaline phosphatase, decreased blood glucose, triglycerides and total cholesterol (p ≤ 0.01) while HDL (p ≤ 0.01) was significantly increased in comparison to obesity and diabetic-obesity groups. Different functional groups presence was confirmed by FTIR spectrum. HPLC analysis revealed the existence of ferulic acid, rutin, chlorogenic acid, coumarin and thymoquinone and these results are corelated by LC-MS/MS. Pre-compression characterization showed angle of repose (33.04°), bulk density (0.54 g/cm3), tapped density (0.73 g/cm3), compressibility index (35.179 %) and Hausner’s ratio (1.35), while the post-compression characterization showed weight variation 826±4.17 mg, thickness 10.50±0.25 kg/cm2, friability 0.57 %, and disintegration time 8.19 min. From the above results it is concluded that F. carica L. leaves extract has strong antioxidant, antidiabetic and hypolipidemic potential and can be used for an obesity and diabetes treatment.

This paper investigates and explores the minor crops production in Pakistan and its association with the agricultural gross domestic product. The agriculture sector of Pakistan has a rich contribution to the economic growth and development. Like major crops; minor crops also have a vital role to boost up the agriculture sector. Time span data was used in this study and it was collected from the Economy Survey of Pakistan annual reports. Augmented Dickey-Fuller (ADF) unit root test and Ordinary Least Square (OLS) method was used to analyze the data and results were interpreted by employing the Johansen co-integration test. Study results reveal that bajra, barely and jowar has a significant impact on the agricultural gross domestic product, while the total cropped area has a negative impact on AGDP. On the basis of the study results, we recommend the policy implications.

Abstract: In recent years, the construction engineering sector has undergone a transformative shift towards the integration of machine learning (ML) techniques, particularly in predicting the properties of steel fiber-reinforced concrete (SFRC). Despite the theoretical sophistication of existing models, a persistent challenge remains – their opacity, lacking transparency and real-world relevance for practi-tioners. To address this gap and advance our current understanding, this study employs the extra gradient (XG) Boosting algorithm, crafting a comprehensive ap-proach. Grounded in a meticulously curated database drawn from 43 seminal pub-lications, encompassing 420 distinct records, this research focuses predominantly on three primary fiber types: crimped, hooked, and mil-cut. Complemented by hands-on experimentation involving 20 diverse SFRC mixtures, this empirical campaign is further illuminated through the strategic use of Partial Dependence Plots (PDPs), revealing intricate relationships between input parameters and con-sequent compressive strength. A pivotal revelation of this research lies in the identification of optimal SFRC formulations, offering tangible insights for real-world applications. The developed ML model stands out not only for its sophistication but also its tangible accuracy, evidenced by exemplary performance against inde-pendent datasets, boasting a commendable mean target-prediction ratio of 99%. To bridge the theory-practice gap, we introduce a user-friendly digital interface, thri-ughly designed to guide professionals in optimizing and accurately predicting the compressive strength of SFRC. This research thus contributes to the construction and civil engineering sectors by enhancing predictive capabilities and refining mix designs, fostering innovation, and addressing the evolving needs of the industry.

At present there is a renewed interest in theories of ”modified” gravity. Here, under a more drastic modification enforced by Galilei group, we obtain a completely new gravitational structure, and which exists in addition to the already available general relativity of today. Correlated with this, we show that in addition, there is a new ”modified” quantum mechanics, in as much as it exists as an independent and new ”pure” non-relativistic quantum me- chanics, and which has no relativistic counterpart. This is in addition to the present quantum mechanics, where the relativistic and non-relativistic structures are counterparts of each other. The above holds, firstly due to the correlation between Galilei group and quantum mechanics. These math- ematical conclusions are consolidated by the fact that there exists a physical Majorana interaction between each neutron- proton pairs in nuclei. Galilei invariance of Majorana exchange in Majorana interaction, shows that the mass here is of pure gravitational nature, and which is immune to the other three forces. This makes an amazing connection between the gravitational force and the quantum mechanics. This pure gravitational mass would man- ifest itself as dark matter of the universe. It is our new modified gravity that generates the dark matter.

Recently several papers have been published on the Liénard equation x'' +L x+m x^3+n x^5=0, where the authors studied their explicit solutions and their applications. Here we describe the complete dynamics of these differential equations in the Poincar\'e disc. The Poincar\'e disc is the closed disc centered at the origin of coordinates of radius one, the whole plane R^2 is identified with the interior of this disc, and its boundary, the circle $\sss^1$ is identified with the infinity of R^2.

General phytochemical screening of the aerial parts of Consolida orientalis revealed the presence of steroids, terpenes, phenolic compounds, saponins, fatty acids, alkaloids. This study was conducted to investigate the bioactivities of extracts, isolation and identification the compounds from aerial parts of C.orientalis. The main goal of the present study is identifying and characterizing the antioxidant activity of the Consolida orientalis and biological isolation of active terpenoid. Aerial parts of the plant were dried at room temperature and reduced to small pieces, followed by using extraction with ethyl acetate percolation. Tree complementary analysis system was used, DPPH free radical scavenging test, total phenolic metabolites and FRAP. The total phenolic content was 38.83±2.09 mg gallic acid corresponding to g-1 extract with regarding to standard curve (y=0.0054x+0.0488, r2=0.995). IC50 value for DPPH radical – scavenging was 987.11±28.66 mgml-1. The extract was exhibited a medium reducing power compared with Vit C. The isolation and purification was afforded white crystalline powder which was subjected to physical, chemical and spectral identification by IR, ¹H- and ¹³C- NMR and GC-MS. Isolated compound was identified as β-sitosterol. That is a terpenoid with melting point 133.4-134.5 ͦ c and with molecular formula C₂₉H₅₀O.

In this paper, we proposed a new model of non-linear electrodynamics with parameter. Firstly, we study the weak limit approximation and by using the Gauss Bonnet theorem, we obtain the deflection angle of photon from magnetized black hole and effect of bnon-linear electrodynamics. In doing so, we find the corresponding optical metric after that we calculate the Gaussian curvature which is used in Gauss Bonnet theorem. Then we show the deflection angle in the leading order terms. We also analyzed that our results reduces into Maxwell's electrodynamics and RN solution with the reduction of parameters. Moreover, we also investigate the graphical behavior of deflection angle w.r.t correction parameter, black hole charge and impact parameter.

In this study, a novel porous geopolymer mortar (GP) was produced and tested experimentally. Industrial waste materials/by-products were used as constituents of the GP, along with dune sand. One sample was produced as a control sample for benchmarking. For the rest of the samples, 15%, 30%, and 45% by volume, the solid constituents were replaced with expanded polystyrene foam (EPS) beads. These mortar samples were heat cured to depolymerize the EPS to cause porosity inside the samples. Indoor experiments were conducted to evaluate the response of produced porous GP to high heat flux. The porous samples were able to reduce heat transmission across the opposite surfaces. Induced porosity resulted in a decrement in compressive strength from 77.2 MPa for the control sample to 15.8 MPa for 45% porous sample. However, the limit lies within the standards for partitioning walls in buildings and pavements in urban areas to absorb rainwater.

This study assesses the pursued impacts of Tulsi value chain development intervention on the livelihoods of rural poor in Uttarakhand state of India. Tulsi as an alternative livelihood, particularly for the rural poor, is less explored. With increased crop depredation of major cereal crops grown in the district by wild animals and pests, and decreasing availability of water agriculture, attempts were made to improve earnings from Tulsi as an alternative livelihood. Findings suggest that the average households’ gross profit from Tulsi farming increases by more than double within a span of two years. Total crop income of beneficiary farmers’ increases by 0.8 percent for every 1 percent increase in Tulsi income. Intervention helped enhance productivity of Tulsi, thereby enhancing earnings from Tulsi farming. Most importantly, intervention has shown a tremendous adoption rate. Towards the end of the intervention, the value chain work was out-scaled to another 19 villages in Chamoli district, thereby reaching out to more than 400 households.

This study aims to formulate binary cementitious systems containing silica fume (SF) and micro quartz (MQ) to improve cementitious concrete's durability and mechanical properties. In this investigation, we examined the effects of different essential variables, such as the level of SF and MQ replacement and the ratio of the water-binder (w/b). In this study, the w/b ratios were 0.25, 0.3, 0.35, and 0.4. Replacement levels for SF were 8, 10, and 12%, while replacement levels for MQ were 5, 8, 10, 15, 25, and 35%. The porosity and permeability decreased with an increase in replacement levels, regardless of the type of fine material used or the amount of replacement. Meanwhile, the strength increased markedly with SF replacement, reaching its maximum MQ of 25% at the SF level. The strength of the SF mixing was the highest in all mixes, and it remained the highest until 15% of MQ was replaced. The ultrafine size of MQ particles contributes to the improvement of compressive strength, porosity, and permeability in a similar way to SF particles, despite their high crystalline structure. Furthermore, in this study, analysis of variance (ANOVA) was employed to verify the influence of each variable on the studied response.

Background: The biofilm-forming bacteria Porphyromonas gingivalis (P. gingivalis) is primarily responsible for periodontal disorders, which continue to be a global health issue. Despite the widespread use of antibiotics like metronidazole, other potent therapeutic a crucial quorum sensing molecule implicated in the formation of P. gingivalis biofilm. Approaches are now being explored due to the growing challenge of antibiotic resistance. Objective: In particular, chemicals from Symphytum Officinale (S) and Panax Ginseng (G) plants will be examined in this study to assess if they have the ability to inhibit biofilm and to prevent the development of acylated homoserine lactones (AHLs), a quorum sensing molecule. Materials and Methods: With Metronidazole serving as a control, the antibacterial effects of these substances (Symphytum Officinale and Panax Ginseng) were examined against a standard strain and a clinical isolate of P. gingivalis. Dilutions of these plant extracts were used either alone (G+S) or in conjunction with metronidazole (G+S+F), to assess their antibacterial activity using antibacterial susceptibility test (inhibition zone), biofilm inhibition and disruption assay (optical density) and quorum sensing inhibition assay (AHL). Results: The combinations of Symphytum officinale, Panax Ginseng and metronidazole (S+G+F) showed the maximum effectiveness with highest zone of inhibition (25.000±0.001 mm) and biofilm inhibition (98.46%), and were comparable to G+S (inhibition zone of 24.341±0.593 mm and biofilm inhibition of 97.76%), and significantly different in the degree of biofilm inhibition with different treatment scenarios. Additionally, the plant's extracts and combinations are specific concentrations had a significant effect on the suppression of the generation of AHL (p < 0.05). Conclusion: According to preliminary research, these plant-derived substances, especially when paired with metronidazole, significantly inhibited the growth of P. gingivalis biofilm providing valuable information for the development of innovative therapeutic approaches for periodontitis and other biofilm-associated illnesses.

Cloud computing has revolutionized how industries store, process, and access data. However, the increasing adoption of cloud technology has also raised concerns regarding data security. Machine learning (ML) is a promising technique to enhance cloud computing security. This paper focuses on utilizing ML techniques (Support Vector Machine, XGBoost, and Artificial Neural Networks) to progress cloud computing security in the industry. The selection of 11 important features for the ML study satisfies the study's objectives. This study focused on identifying gaps in utilizing ML techniques in cloud cyber security. Moreover. this study aims at developing a practical strategy for predicting the employment of machine learning in an Industrial Cloud environment regarding trust and privacy issues. The efficiency of the employed models is assessed by applying validation matrices of Precision, Accuracy, Recall values, F1 score, R.O.C. curves, and Confusion matrix. The results demonstrated that the X.G.B. model outperformed in terms of all the matrices with an Accuracy of 97.50 %, 97.60 % Precision, 97.60 % Recall values, and 97.50 % F1 score. This research highlights the potential of ML algorithms in enhancing cloud computing security for industries. It emphasizes the need for continued research and development to create more advanced and efficient security solutions for cloud computing.

Rat is one of the most commonly used model animals for biological research. The organs and systems of human being are somewhat similar to that of rat in structure as well as functions, making it a valuable choice for research experimentation in biological sciences. A number of studies have been conducted to evaluate the potential risks and toxicity of different elements on the physiology and histology of rats. There is need to address certain environmental factors affecting rats condition during experimentation. Reproduction along with its pathologies is under investigation on larger scale throughout the world, being central for the existence of a species. These studies focus on the major factors that influence reproductive function. Review of literature clearly indicated the unwanted consequences of over nutrition, malnutrition, high or low temperature, non-enriched housing, improper handling, intense or poor light exposure and environmental pollution on histology and hormonal profile of reproductive system of rats.

In this study, the prevalent methodology for design of the industrial policy in developing countries was critically assessed, and it was shown that the mechanism and content of classical method is fundamentally contradictory to the goals and components of the endogenous growth theories. This study, by proposing a new approach, along settling Schumpeter's economic growth theory as a policy framework, designed the process of entering, analyzing and processing data as the mechanism of the industrial policy in order to provide "theoretical consistency" and "technical and Statistical requirements" for targeting the growth stimulant factor effectively.

Artificial intelligence (AI) systems of autonomous systems such as drones, robots and self-driving cars may consume up to 50% of total power available onboard, thereby limiting the vehicle’s range of functions and considerably reducing the distance the vehicle can travel on a single charge. Next-generation onboard AI systems need an even higher power since they collect and process even larger amounts of data in real time. This problem cannot be solved using the traditional computing devices since they become more and more power-consuming. In this review article, we discuss the perspectives of development of onboard neuromorphic computers that mimic the operation of a biological brain using nonlinear-dynamical properties of natural physical environments surrounding autonomous vehicles. Previous research also demonstrated that quantum neuromorphic processors (QNPs) can conduct computations with the efficiency of a standard computer while consuming less than 1% of the onboard battery power. Since QNPs is a semi-classical technology, their technical simplicity and low, compared with quantum computers, cost make them ideally suitable for application in autonomous AI system. Providing a perspective view on the future progress in unconventional physical reservoir computing and surveying the outcomes of more than 200 interdisciplinary research works, this article will be of interest to a broad readership, including both students and experts in the fields of physics, engineering, quantum technologies and computing.

Deep neural networks (DNNs) have made a huge impact in the field of machine learning by providing unbeatable humanlike performance to solve real-world problems such as image processing and natural language processing (NLP). Convolutional neural network (CNN) and recurrent neural network (RNN) are two typical architectures that are widely used to solve such problems. Time sequence-dependent problems are generally very challenging, and RNN architectures have made an enormous improvement in a wide range of machine learning problems with sequential input involved. In this paper, different types of RNN architectures are compared. Special focus is put on two well-known gated-RNN’s Long Term Short Memory (LSTM) and Gated Recurrent Unit (GRU). We evaluated these models on the task of force estimation system in pouring. In this study, four different models including multi-layers LSTM, multi-layers GRU, single-layer LSTM and single-layer GRU) were created and trained. The result suggests that multi-layer GRU outperformed other three models.

From the hospital wastewater, a novel bacteriophage was isolated and characterized. According to characterization properties, this bacteriophage belongs to the Siphoviridae family, the maximum bacteriophage titer was recorded at 37°C and a pH of 7.2, had a 44,789 bp linear double-strand DNA genome, and within the genome sequence, there are 61 genes, all of which are encoded into proteins. Although this bacteriophage does not have any virulence factors or antimicrobial resistance genes and had specific lytic activity against some antimicrobial resistance S. aureus clinical isolates.

Since the beginning, humans advanced their civilization by making better tools to improve their lives. Tools and products were designed for better living considering manufacturing issues, cost and time as predominant criteria. It has become clear that not considering environment and society, both at local/global levels, has now become a major impediment affecting living conditions on a large portion of the Earth and in many societies. Design methodologies should lead to creative solutions with consideration to engineering and economics for practicality but also to environmental and social constraints for sustainability. We propose a comprehensive design methodology based on multidisciplinary design to include the knowledge of humanities, environmentalists, science and engineering, and allowing for experts’ inputs from these areas to provide a holistic approach to engineering design . For example, experts in humanities are expected to interact with stakeholders to evaluate their value systems to provide guidance for the design. The methodology that we synthesize is new and combines (i) Societal level impacts at all scales, (ii) Environmental impacts and (iii) Engineering design with economic impacts, including uncertainty considerations. The proposed design methodology is called Social-Environmental-Economical-Engineering Framework (SEEEF). It can utilize concepts and tools such as Circular Design, Doughnut Economics, design based on environmental life cycle analysis, among others. SEEEF is quantity based and provides steps for evaluating any project or product in an objective manner and will help train engineers in design for sustainability. It also provides non-engineers with a significant role in design to increase their understanding of the hard constraints of engineering. Ultimately, SEEEF allows society to take an informed decision considering short/long term and local/global impacts of the design and the pertinent uncertainties.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

Kynurenine or tryptophan catabolite (TRYCAT) pathway contributes to the pathophysiology of major depression disorder (MDD) and major depressive episodes (MDE) in bipolar disorder and suicidal behaviors. The consequences of the overactivation of this pathway large reduced tryptophan (TRP) levels in peripheral blood and the CNS and increased levels of neurotoxic TRYCATs including kynurenine (KYN), 3-hydroxy kynurenine (3HK), quinolinic acid (QA), xanthurenic acid (XA), and picolinic acid (PA). However, other TRYCATs are protective, such as kynurenic acid (KA) and anthranilic acid (AA). Inflammation and cell-mediated immune activation along with oxidative and nitrosative stress (O&NS) may stimulate the first and rate-limiting enzyme of this pathway, namely indoleamine-2,3-dioxygenase (IDO). Therefore, during depression, balancing neuroprotective versus neurotoxic TRYCATs and balancing activation of the immune response system (IRS) versus the compensatory immune response system is crucial for achieving better treatment outcomes. Furthermore, targeting the causes of TRYCAT pathway activation (immune activation and O&NS) is probably the most effective strategy to treat depression. In the present review, we aim to provide a comprehensive explanation of the impact of TRYCATs in terms of pathophysiology and treatment of MDD and MDE.

Higher order femtoscopy measured to examine the heat exchanger characterization of the fluid debris produced in the collisions and investigated a remarkable suppression in the bosons interferences measurement. The analogous suppression can be analyzed to explore the coherence of boson thermal particle production sources at unprecedented energies. We illustrate the particles emissions from radiated sources with statistical coherence which induce the thermal particles interferences to probe the peculiarity of the heated sources as well as the distinctions about the heat exchangers in the collisions at higher temperature. We perspicacious that the bosons seem to the pertinent aspirant of heat exchanger, and the normalized three particles correlators evaluate the existence of such hybrid phases significantly. The key point of this research is that we analyze the three particles correlations with their normalized correlations by difference equations to determine the characteristics of heat exchanger and its applications. With such distinctive and efficient approach, we observe a significant difference in the correlation functions at higher temperature and momenta regimes.

The coronavirus COVID-19 epidemic has wreaked havoc on inhabitants of earth killing thousands of humans from more than 150 countries. The epidemic has put a number of countries under complete lockdown and the deadly situation is still prevailing around the globe. Vaccines have been long known as the most effective means of preventing viral infections. However, the lack of vaccines against COVID-19 has further worsened the situation. In this time of health crisis, it is the duty of scientific research community to provide alternative, effective and affordable strategies to vaccinate human bodies against viral infections-COVID-19 based on focused experimental approaches. Growing evidence suggests that certain natural foods and lifestyle changes have potential to optimize immune functions against viral infections including improving defense function, resistance towards invading pathogens, while maintaining self-tolerance. Boosting immune system gives an edge in fending off viruses and staying healthy. This review presents the six smart steps to add to your to-do list which let the inner work of immunity take place against viral infections-COVID-19 by dissolving the powers of disease and illness. Many of these factors are associated in their functions to improve or properly maintain the immune function such as promoting anti-inflammatory functions, inhibiting pro-inflammatory mediators, modulating cell-mediated immunity, altering the antigen-presenting cellular functions as well as promoting communication between the innate and adaptive immune responses. Thus, a scientific illustration of boosting the immune system by proper sleep, moderate exercise, avoiding stress, utilizing vitamins enriched foods, intake of more water and use of fruits and vegetables will hopefully help the community to deal with the coronavirus by vaccinating the human systems naturally.

Schizophrenia comprises various symptom domains, including positive and negative symptoms. Machine learning showed that a) negative symptoms are significantly interrelated with PHEM (psychosis, hostility, excitation, and mannerism) symptoms, formal thought disorders (FTD) and psychomotor retardation (PMR); and b) stable phase schizophrenia comprises two distinct classes, namely Major Neuro-Cognitive Psychosis (MNP, largely overlapping with deficit schizophrenia) and Simple NP (SNP). In this study, we recruited 120 MNP patients and 54 healthy subjects and measured the above-mentioned symptom domains. In MNP, there were significant associations between negative and PHEM symptoms, FTD and PMR. A single latent trait, which is essentially unidimensional, underlies these key domains of schizophrenia and MNP and additionally shows excellent internal consistency reliability, convergent validity, and predictive relevance. Confirmatory Tedrad Analysis indicates that this latent vector fits a reflective model. The lack of discriminant validity shows that PHEM and negative symptoms greatly overlap and probably measure the same construct. Soft Independent Modeling of Class Analogy (SIMCA) shows that MNP (diagnosis based on negative symptoms) is better modeled using PHEM symptoms, FTD, and PMR than negative symptoms. In conclusion, in stable phase MNP, a restricted sample of the schizophrenia population, negative and PHEM symptoms, FTD and PMR belong to one underlying latent vector reflecting overall severity of schizophrenia (OSOS). The bi-dimensional concept of “positive” and “negative” symptoms cannot be validated and, therefore, future research in stable phase schizophrenia should consider that the latent phenomenon OSOS as well as its 8 reflective manifestations are the key factors of schizophrenia phenomenology.

Chronic Kidney Disease (CKD) is one of the worldwide health threats, kidneys may be affected by internal pathologies and environmental factors as well as a number of genes are also involved in the kidney dysfunctioning, so UMOD is one of these genes which has significant effect in regulating urea and creatinine level in blood and decreased excretion of uric acid which causes interstitial damages in kidney and may result CKD. Hence, the present study is envisaged to observe the association of this gene locus (r.1264T>C) with CKD in Pakistani population using ARMS-PCR genotyping, for the purpose, a total of 75 samples were investigated, out of which 45 were found homozygous wild-type, 21 heterozygous and 09 homozygous mutants. PLINK data analysis toolset showed that our sampled population does not obeys Hardy-Weinberg Equilibrium by χ² (2, N = 75) = 18.87, p = and Chi-square statistics with p = 1.40×10^-005 showing a significant genotypic association with the subject phenotype with an alternative allele frequency of 0.15 and 0.48 within cases & controls respectively. Furthermore, an odds-ratio of 0.2 predicts that the risk of wild-type allele (A) is 0.8 times higher in patient as compared to controls and mutant allele is 0.2 times preventive in patients. Additionally, a few bioinformatics tools e.g., ProtParam, PsiPred, TMHMM-2.0, Motif Scan, ScanProsite, NetPhos3.1, GPS PAIL2.0, NetOGlyc4.0, PRmePRed, PDB-RCSB and STRING were applied to predict different characteristics of Uromodulin protein including physicochemical properties, secondary/transmembrane structures, protein conserved domains and posttranslational modifications respectively. This pilot scale study provided a comprehensive insight of the association of aforementioned genetic variant with CKD to identify and evaluate the genetic risk factors along with functional effects of the subject variant which may be used as CKD prevention by adopting DNA screening and genetic counselling recommendations.

In this study, we present different methods of estimating fuzzy reliability of a two-parameter Rayleigh distribution via the maximum likelihood estimator, median first-order statistics estimator, quartile estimator, L-moment estimator, and mixed Thompson-type estimator. The mean-square error MSE as a measurement for comparing the considered methods using simulation through different values for the parameters and unalike sample sizes is used. The results of simulation show that the fuzziness values are better than the real values for all sample sizes, as well as the fuzzy reliability at the estimation of the Maximum

Enteropathogenic microorganisms like Escherichia coli cause severe intestinal problems by disrupting the gut homeostasis. The live microorganisms, when given in adequate quantities provide several beneficial effects to the host are known as probiotics. One of the pronounced benefits conferred by probiotic is to antagonize the growth of enteropathogens competing for adherence to the intestinal epithelium. Bifidobacterium is the major genera of human especially infant are intestinal microbiota. In current study, Bifidobacterium bifidum was isolated from the infant stools and probiotic potential was assessed using prescribed tolerance tests against low pH, gastric juices and bile salts. Anti-infectious activity of probiotic Bifidobacterium bifidum against enteropathogenic E. coli was checked both in vitro and in vivo using agar well diffusion assay and mice model respectively. Mice feces were evaluated for both Bifidobacterium bifidum and E. coli counts in all groups and analyzed statistically. In vitro results showed Bifidobacterium bifidum possess marked antibacterial activity against E. coli. There was significant decrease in enteropathogenic E. coli burden in the mice group fed with Bifidobacterium bifidum before and after challenge. In conclusion, the endogenous Bifidobacterium bifidum have excellent probiotic potential and can be used prophylactic and treatment option against enteropathogens.

Water resources planners and policymakers often ask questions about the future projections of drought characteristics (events, intensity, severity, duration, and peak) under different climatic scenarios. This study focused on quantifying the historical (1951-2005) and future (2026-2100) drought characteristics using the Standardized precipitation index (SPI) under RCP 4.5 and RCP 8.5 climate scenarios for the Balochistan province of Pakistan, an arid and drought-vulnerable region. Precipitation data of MPI-ESM-LR_RCA4 RCM was obtained from the Coordinated Regional Climate Downscaling Experiment South Asia (CORDEX-SA). The CORDEX-SA data was interpolated at 12-gauge stations and bias-corrected by the distribution mapping method using Asian Precipitation - Highly-Resolved Observational Data Integration towards Evaluation (APHRODITE) data. The drought characteristics were calculated based on standardized precipitation index (SPI), and intercompared between northern Balochistan (NB) and southern Balochistan (SB). It was found that the northern Balochistan (NB) region has suffered more droughts in the historical period and is also projected to have more severe and intense droughts than SB region. It was also found that with the increase of drought events, the duration reduces, which means that the higher the drought events at a station, the lower the drought duration. Government officials should focus more on managing the already few freshwater resources sustainably, given the increased likelihood of droughts in Balochistan due to climate change.

Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

The most frequent, noticeable, and frequent natural calamity in the karakoram region is landslides. Extreme landslides have occurred frequently along Karakoram highway, particularly during the monsoon, causing a major loss of life and property. Therefore, it was necessary to look for a solution to increase growth and vigilance in order to lessen losses related to landslides caused by natural disasters. By utilizing contemporary technologies, an early warning system might be developed. Artificial neural networks (ANNs) are widely used nowadays across many industries. This paper's major goal is to provide new integrative models for assessing landslide susceptibility in a prone area of north of Pakistan. To do this, the training of an artificial neural network (ANN) is supervised using metaheuristic and Bayesian techniques: particle swarm optimization algorithm (PSO), Genetic algorithm (GA), Bayesian optimization Gaussian process (BO_GP), and Bayesian optimization Gaussian process (BO_TPE). 304 previous landslides and the eight most prevalent conditioning elements combine to form a geographical database. The models are hyper-parameter optimized, and the best ones are employed to generate the susceptibility maps. The area under the receiving operating characteristic curve (AUROC) accuracy index found demonstrated that the maps produced by both Bayesian and metaheuristic algorithms are highly accurate. The effectiveness and efficiency of applying artificial neural networks (ANNs) for landslide mapping, susceptibility analysis, and forecasting are studied in this research it’s observed from experimentation that the performance differences for GA, BO_GP, and PSO compared to BO_TPE are relatively small, ranging from 0.3166% to 1.8399%. This suggests that these techniques achieved comparable performance to BO_TPE in terms of AUC. However, it's important to note that the significance of these differences can vary depending on the specific context and requirements of the ML task. Additionally in this study, we explore eight feature selection algorithms to determine the geospatial variable importance for landslide susceptibility mapping along the KKH. The algorithms considered include Information Gain, Gain Ratio, OneR Classifier, Subset Evaluators, Principal Components, Relief Attribute Evaluator, Correlation, and Symmetrical Uncertainty. These algorithms enable us to evaluate the relevance and significance of different geospatial variables in predicting landslide susceptibility. By applying these feature selection algorithms, we aim to identify the most influential geospatial variables that contribute to landslide occurrences along the KKH. The algorithms encompass a diverse range of techniques, such as measuring entropy reduction, accounting for attribute bias, generating single rules, evaluating feature subsets, reducing dimensionality, and assessing correlation and information sharing. The findings of this study will provide valuable insights into the critical geospatial variables associated with landslide susceptibility along the KKH. These insights can aid in the development of effective landslide mitigation strategies, infrastructure planning, and targeted hazard management efforts. Additionally, the study contributes to the field of geospatial analysis by showcasing the applicability and effectiveness of various feature selection algorithms in the context of landslide susceptibility mapping.

Condition monitoring is a primary principle for predictive maintenance. In this regard, several techniques have been employed, each of which has its strengths and weaknesses. In this work, the relationships between the electrical (ε', ε", tan δ) and chemical (Fe, Pb, Cu, Cr, Al, Si, Zn) properties of engine lubricants were investigated using soft computing models. The models' performance was evaluated considering some criteria, including RMSE and MAPE. The RBF model was determined as the best one to predict chemical properties (Fe, Pb, Cu, Cr, Al, Si, Zn) through electrical indexes (ε', ε", tan δ). The RBF’s parameters (e.g., hidden size and training algorithm) were then optimized for optimum performance. For instance, in the RBF model implemented to predict Al, the best hidden size and training algorithmic were 15 and 'trainlm', respectively. Finally, by sensitivity analysis it was observed that eliminating any of the inputs does not improve the performance of the RBF model performance. In general, the results of the current research showed that the electrical properties (e.g., ε', ε", tan δ) have the capability of estimating the contaminants in the lubricants which can improve the existing monitoring methods.

Nutrients management is a mainspring in agricultural systems for sustained productivity, economy sustainability and environmental quality. Excessive and lesser nutrient application caused environmental pollution and reduced production, respectively impacting socio-economics of the entire ecosystems. Sustainable agricultural production thus demands supplementation of nutrients either through natural processes, application of animal by-products, and mineral fertilizers to crop fields. Technology application for treating useless agricultural wastes into useful source is a management strategy that prevents environment pollution. Crude animal manures triggered soil degradation, attenuation air and water quality, and resulted in higher concentrations of heavy metals. Primary nutrients, i.e., nitrogen, phosphorus and potassium are used globally and are non-renewable. Augmented upsurge in prices of inorganic fertilizers and required discharge restrictions on nutrient has stimulated the technological developments including biochar, composting, vermicomposting, composting with biochar, pyrolysis, forward osmosis, and electro-dialysis to recover nutrients. Therefore, outlining the research gaps considering the present and imminent potential of these technologies for adaptation of nutrient recycling is of great importance. Thus, it’s need of an hour to fix our environment and for that scientists are trying to introduce and renovate the technologies which have immense potential to mitigate the negative effects of technology adversities on our environment.

Lamb wave-based structural health monitoring is widely acknowledged as a reliable 11 method for damage identification, classification, localization and quantification. However, due to 12 the complexity of Lamb wave signals, especially after interacting with structural components and 13 defects, interpreting these waves and extracting useful information about the structure's health is 14 still a major challenge. However, deep learning-based strategy offers a great opportunity to address 15 such challenges as the algorithm can operate directly on raw discrete time-domain signals. Unlike 16 traditional methods, which often require careful feature engineering and preprocessing, deep learn-17 ing can automatically extract relevant features from the raw data. This paper proposes an autoen-18 coder based on a bidirectional long short-term memory network with maximal overlap discrete 19 wavelet transform layer to detect the signal anomaly and determine the location of the damage in 20 the composite structure. This approach has the potential to greatly enhance our ability to detect and 21 locate structural damage in composite structures, thereby increasing safety and efficiency.

The escalating reliance of modern society on information and communication technology has rendered it vulnerable to an array of cyber-attacks, with distributed denial-of-service (DDoS) at-tacks emerging as one of the most prevalent threats. This paper delves into the intricacies of DDoS attacks, which exploit compromised machines numbering in the thousands or more to disrupt data services and online commercial platforms, resulting in significant downtime and financial losses. Recognizing the gravity of this issue, various detection techniques have been explored, yet the quantitative and prior detection of DDoS attacks has seen a decline in recent methods. This research introduces an innovative approach by integrating evolutionary optimization algorithms and machine learning techniques. Specifically, the study proposes XGB-GA Optimization, RF-GA Optimization, and SVM-GA Optimization methods, employing Evolutionary Algorithms Opti-mization with TOPOT-Genetic Programming. Datasets pertaining to DDoS attacks were utilized to train machine learning models based on XGB, RF, and SVM algorithms, and 10-fold cross-validation was employed. The models were further optimized using evolutionary algo-rithms, achieving remarkable accuracy scores: 99.99% with the XGB-GA method, 99.50% with RF-GA, and 99.99% with SVM-GA. Furthermore, the study employed TPOT to identify the optimal algorithm for constructing a machine learning model, with the genetic algorithm pinpointing XGB-GA as the most effective choice. This research significantly advances the field of DDoS attack detection by presenting a robust and accurate methodology, thereby enhancing the cybersecurity landscape and fortifying digital infrastructures against these pervasive threats.

The electrochemical CO2 reduction reaction can lead to high value-added molecules production while helping decrease anthropogenic CO2 emissions. Copper can reduce CO2 to more than thirty different hydrocarbons and oxygenates, but it lacks the required selectivity. We present a computational investigation of the role of nano-structuring and alloying in Cu-based catalysts on the activity and selectivity of CO2 reduction to one-carbon products: carbon monoxide, formic acid, formaldehyde, methanol, and methane. The adsorption, activation, and conversion of CO2 were computed on monometallic and bimetallic (decorated and core-shell) 55-atom Cu-based clusters. The dopant metals considered were Ag, Cd, Pd, Pt, and Zn, located at different coordination sites. The relative binding strength of the intermediates at different applied potentials were used to identify the optimal catalyst for the selective CO2 conversion to one carbon products. It was discovered that single atom doping with Cd and Zn is optimal for the CO2 to carbon monoxide conversion. The core-shell models with Ag, Pd, and Pt provided higher selectivity for formic acid and formaldehyde. The Cu-Pt and Cu-Pd showed lowest overpotential for methane formation.

Electro-spun ultra-fine fibers exhibit two significant properties: a high surface-to-volume ratio and a relatively defect-free molecular structure. Due to the high surface-to-volume ratio, electro-spun materials are well suited for activities requiring increased physical contact, such as providing a site for a chemical reaction or filtration of small-sized physical materials. However, electrospinning has many shortcomings, including difficulties in producing inorganic nanofibers and a limited number or variety of polymers used in the process. The fabrication of nanofiber bundles via electrospinning is explored in this analytical study, as well as the relationship between extrinsic electrospinning parameters and the relative abundance of various fiber morphologies. Numerous variables could impact the fabrication of nanofibers, resulting in a variety of morphologies; therefore, adequate ambient conditions and selecting the appropriate solvent for achieving a homogenous polymer solution and uniform electro-spun materials are examined. Finally, common polymers suitable for electrospinning and the promising applications of ultra-fine fibers achieved via electrospinning are studied in this paper.

Radical prostatectomy (RP) is one of the recommended treatments to achieve oncological outcomes in localized prostate cancer. However, radical prostatectomy is a major abdominopelvic surgery. Venous thromboembolism (VTE) is a well-known complication associated with surgical procedures including RP. There is a lack of consensus regarding VTE prophylaxis in urological procedures. The aim of this systematic review was to investigate different aspects of VTE in post-Radical Prostatectomy patients. A comprehensive literature search was performed, and relevant data were extracted. The primary aim was to perform a systematic review and meta-analysis (wherever possible) of VTE occurrence in post-RP patients in relation to surgical approach, pelvic lymph node dissection, and type of prophylaxis (mechanical or combined prophylaxis). The secondary aim was to investigate- the incidence and other risk factors of VTE in post-RP patients. A total of 16 studies were included for quantitative analysis. Statistical methods for analysis included the DerSimonian-Laird random effects. We were able to conclude that the overall incidence of VTE in post-radical prostatectomy is 1% and minimally invasive procedures (MIS), including laparoscopic as well as robotic procedures for radical prostatectomy and RP without pelvic lymph node dissection (PLND) are associated with less risk of developing VTE. Additional pharmacological prophylaxis to mechanical methods may not be necessary in all cases and should be considered in high-risk patients only.

Transportation contributes significantly to greenhouse gas emissions, with electrification offering a promising solution. This study evaluates the degradation of State of Health (SOH) over 2.5 years for electrified buses under different charging protocols: DC Fast charging and Flash charging. The vehicles’ models, charging protocols, and financial implications are discussed. High-level simulations reveal that after 2.5 years, the Flash charging vehicle’s SOH reaches 88.93%, while the DC fast charging vehicle reaches 89.46%, showing a 0.47% difference. This slight variance is attributed to Flash charging vehicles avoiding full charge/discharge cycles, reducing battery aging impact. Considering this minimal SOH degradation difference, the choice between DC Fast charging and Flash charging primarily hinges on capital expenditure disparities. Flash charging, with its lower initial battery capacity and reduced capital costs, presents a compelling alternative for city busoperators seeking to electrify their fleets.

The modeling and prediction of crop seed yield can be a vital improvement in the precision agriculture industry as it provides reliable assessments of the effectiveness of agro-traits. Here, multiple machine learning (ML) techniques are established for predicting sesame (Sesamum indicum L.) seed yield (SSY) and incorporating agro-morphological features. Models utilized for coupled PCA-ML (Principal component analysis-Machine Learning) methods were compared with original ML models to evaluate predicted efficiency. The Gaussian process regression (GPR) and Radial basis function neural network (RBF-NN) models exhibited the most accurate SSY predictions with determination coefficients or R2 values of 0.99 and 0.91, respectively. The root-mean-square error (RMSE) for the ML models fluctuated between 0 to 0.30 t/ha (metric tons/hectare) for the varied modeling process phases. Estimation of sesame seed yield with coupled PCA-ML models improved performance accuracy. The K-fold process suggested the utilization of datasets with the lowest error rates to ensure the continued accuracy of GPR and RBF models. Sensitivity analysis revealed the capsule number per plant (CPP), seed number per capsule (SPC), and 1000-seed weight (TSW) were the most significant seed yield determinants.

The high figure of merit and earth abundance of Cu₁₂Sb₄S₁₃ thermoelectric ma- terials have recently attracted many attentions toward these type of complex compounds. Intrinsic low thermal conductivity, as well as tunable electronic transport properties, make them suitable for thermoelectric power generation. In this study, we perform a comparative theoretical study on the substituted compounds, primarily at the Cu site including known tetrahedrite Cu₁₂Sb₄S₁₃, by means of first-principles calculations. The density functional theory of electric structure is applied to investigate the result of substitution.

CONTEXT– Energy is widely involved in human activity and corresponding emissions of SOX, NOX and CO2 from energy generation processes affect global climate change. Clean fuels are desired by society because of their reduced greenhouse gas emissions. Hydrogen is once such candidate fuel. Much hydrogen is produced from fossil fuel, with biomass being an alternative process. OBJECTIVE– The project compared the environmental impact of hydrogen production by natural gas steam reforming vs. biomass gasification. METHOD–Environmental impact was calculated from the input and output data from life cycle inventory analysis. The impact assessment was focused on greenhouse gas emission, acidification, and eutrophication. Models of the two processes were developed and analysed in OpenLCA. The agribalyse database was used to connect inventory flow data to environmental impacts. FINDINGS– For all three metrics, biomass gasification had lower impacts than natural gas steam reforming, sometimes by large margins. For biomass gasification the silica sand production contributes most to all three impact categories, whereas for natural gas steam reforming it is the LPG extraction.

Based on the resource-based theory, the current study examines the relationship between competitive strategies and strategic alliance performance. Furthermore, big data predictive analytics is treated as a boundary condition between competitive strategies and strategic alliance performance. Big data of predictive analytics in operations and industrial management has been a focal point in the current era. There has been little attention has about big data predictive analytics influences on competitive strategies and strategic alliance performance, especially in developing countries like Pakistan. A survey instrument was used to record the responses from 331 employees of the telecom sectors companies working in Pakistan. Study findings show that big competitive strategies have a positive and significant relationship with strategic alliances performance. It was also found that big data predictive analytics plays the role of moderator between competitive strategies and strategic alliance performance. The study add a new perspective and contribution to the literature on big data predictive analytics, strategic alliance performance, and competitive strategies in Pakistan's telecom sector companies. Further, the study results explain that big data analytics is just like the companies' lifeblood in the current era. The efficient and effective use of big data analytics, companies can boost their standards in a competitive environment.

In this work, we study the weak gravitational lensing in the background of Kerr-Newman black hole with quintessential dark energy. Initially, we compute the deflection angle of light by charged black hole with quintessential dark energy by utilizing the Gauss-Bonnet theorem. Firstly, we suppose the light rays on the equatorial plane in the axisymmetric spacetime. In doing so, we first find the corresponding optical metrics and then calculate the Gaussian optical curvature to utilize in Gauss-Bonnet theorem. Consequently, we calculate the deflection angle of light for rotating charged black hole with quintessence. Additionally, we also find the deflection angle of light for Kerr-Newman black hole with quintessential dark energy. In order to verify our results, we derive deflection angle by using null geodesic equations which reduces to the deflection angle of Kerr solution with the reduction of specific parameters. Furthermore, we analyze the graphical behavior of deflection angle $\Theta$ w.r.t to quintessence parameter $\alpha$, impact parameter $b$, BH charge $Q$ and rotation parameter $a$. Our graphical analysis retrieve various results regarding to the deflection angle by the Kerr-Newman black hole with quintessential dark energy.

In this paper, we are interested in a model of exact asymptotically flat charged hairy black holes in the background of dilaton potential. We study the weak gravitational lensing in the spacetime of hairy black hole in Einstein-Maxwell theory with a non-minimally coupled dilaton and its non-trivial potential. In doing so, we use the optical geometry of the flat charged hairy black hole for some range of parameter $\gamma$. For this purpose, by using Gauss-Bonnet theorem, we obtain the deflection angle of photon in a spherically symmetric and asymptotically flat spacetime. Moreover, we also investigate the impact of plasma medium on weak gravitational lensing by asymptotically flat charged hairy black hole with a dilaton potential. Our analytically analyses show the effect of the hair on the deflection angle in weak field limits.

Background. The aim of this study is to examine whether biomarkers of the immune-inflammatory response (IRS) and endogenous opioid (EOS) systems are associated with affective symptoms in schizophrenia. Methods. We recruited 115 schizophrenia patients and 43 healthy controls and assessed the Hamilton Depression (HDRS) and Anxiety (HAM-A) rating Scale scores as well as serum levels of interleukin (IL)-6, IL-10, eotaxin (CCL11), high mobility group box 1 (HMGB1), Dickkopf-related protein 1 (DKK1), and mu (MOR) and kappa (KOR) opioid receptors.Results. The HDRS and HAM-A scores are significantly and positively correlated with a) psychosis, hostility, excitation, mannerism, negative symptoms, psychomotor retardation, and formal thought disorders; and b) lowered scores on semantic and episodic memory, executive functions, and attention tests as measured with the Brief Assessment of Cognition in Psychiatry. Both HDRS and HAM-A are significantly increased in non-responders to treatment as compared with partial responders. Both affective scores are strongly associated with latent vectors extracted from all symptoms, reflecting overall severity of psychosis (OSOS), and neurocognitive test scores, reflecting a generalized cognitive decline (G-CoDe). The HDRS score was strongly and positively associated with IL-6, HMGB1, KOR, and MOR levels, and the HAM-A score with IL-6, IL-10, CCL11, HMGB1, KOR, and MOR levels. A single latent trait may be extracted from OSOS, G-CoDe, and the HDRS and HAMA scores, and this latent vector score is strongly predicted by HMGB1, MOR, and DKK1.Conclusion. Immune-inflammatory and EOS pathways contribute to the phenome of schizophrenia, which comprises OSOS, affective, and physiosomatic symptoms, and G-CoDe.

No studies have examined the immune fingerprint of major neuro-cognitive psychosis (MNP) or deficit schizophrenia using M1 macrophage cytokines in combination with chemokines such as CCL-2 and CCL-11. The present study delineated the neuro-immune fingerprint of MNP/deficit schizophrenia by analyzing plasma levels of IL-1β, sIL-1RA, TNF-α, sTNFR1, sTNFR2, CCL-2 and CCL-11 in MNP (n=120) versus healthy controls (n=54) in association with neurocognitive deficits (as assessed with the Brief Assessment of Cognition in Schizophrenia) and PHEMN (psychotic, hostility, excitation, mannerism and negative) symptoms. All immune biomarkers were significantly higher in MNP than in normal controls. MNP was best predicted by a combination of CCL-11, TNF-α, IL-1β and sIL-1RA which yielded a bootstrapped (n=2000) area under the Receiver Operating Curve of 0.985. Composite scores reflecting M1 macrophage activity and neurotoxic potential including combined effects of CCL-11 plus CCL-2 were significantly increased in MNP. Nevertheless, the effects of increased IL-1β and TNF-α in MNP were attenuated (statistically) by increased sIL-1RA and sTNFR2, two negative immune-regulatory markers. A large part of the variance in PHEM (38.4%-52.6%) and negative (65.8-7439%) symptoms was explained by combinations of immune markers whereby CCL-11 was consistently the most important. The immune markers also explained a large part of the variance in the Mini Mental State examination, list learning, digit sequencing task, category instances, controlled word association, symbol coding and Tower of London. Soft Independent Modeling of Class Analogy performed on the biomarkers showed that the inter-class distance between the models constructed around MNP and controls was 19.3 indicating a good separation. Partial Least Squares analysis showed that 72.7% of the variance in overall phenomenology was explained by the regression on IL-1β, sIL-1RA, CCL-11, TNF-α (all positively) and education (inversely). It is concluded that the combination of the above-mentioned markers defines MNP as a distinct neuro-immune disorder and that those markers in combination explain a large part of the variance in memory and executivive impairments and PHEMN symptoms.

This research paper aims to examine the relationship between CO2, temperature, area, fertilizers and rice production in Pakistan. This study used Augmented Dickey Fuller (ADF) and Phillips Perron (PP) unit root tests to check the order of integration of each variable. The cointegration analysis with ARDL bounds testing approach is used to examine the impact of climate change on rice production in Pakistan over time series data from the period 1968 to 2014. The parameter stability test of the model is also checked at the end. The results of estimation show that the important variables of the study are cointegrated demonstrating the presence of long-run association among them. Furthermore, climate change factors, e.g. CO2 and temperature have a long-run and short-run positive effect on the production of rice in Pakistan. This present work is original and it is first time empirically tested the impact of climate change on rice production in Pakistan. The annual time series data of 47 years enhances the validity of the empirical findings. The most fruitful finding of this research is that rice production in Pakistan is positively influenced by emission of carbon dioxide (CO2) at 5 percent significance level in both long-run and short-run.

We employ the solution concept of ex post Nash equilibrium to predict the interaction of a finite number of agents competing in a finite number of basic games simultaneously. The competition is called a multi-game. For each agent, a specific weight, considered as private information, is allocated to each basic game representing its investment in that game and the utility of each agent for any strategy profile is the weighted sum, i.e., convex combination, of its utilities in the basic games. Multi-games can model decision making in multi-environments in a variety of circumstances, including decision making in multi-markets and decision making when there are both material and social utilities for agents as, we propose, in the Prisoner's Dilemma and the Trust Game. Given a set of pure Nash equilibria, one for each basic game in a multi-game, we construct a pure Bayesian Nash equilibrium for the multi-game. We then focus on the class of so-called uniform multi-games in which each agent is constrained to play in all games the same strategy from an action set consisting of a best response per game. Uniform multi-games are equivalent to multi-dimensional Bayesian games where the type of each agent is a finite dimensional vector with non-negative components. A notion of pure type-regularity for uniform multi-games is developed and it is shown that a multi-game that is pure type-regular on the boundary of its type space has a pure ex post Nash equilibrium which is computed in constant time with respect to the number of the types and is independent of prior probability distributions. We then develop an algorithm, linear in the number of types of the agents, which tests if a multi-game is pure type-regular on the boundary of its type space in which case it returns a pure ex post Nash equilibrium for the multi-game.

Diabetes mellitus remains a major risk factor for developing cardiovascular diseases, resulting in increased morbidity and mortality associated with cardiovascular complications. Given the burden of diabetes-related cardiovascular complications, there is a need to identify strategies, safe and effective therapeutic agents that could effectively prevent and control diabetes. Presently, many patients living with diabetes depends on traditional medicines as an alternative cure. Channa striatus (Haruan) is a freshwater fish traditionally used to treat wounds, inflammations, and pains. Several pharmacological investigations have supported the folkloric claims of C. striatus extracts, including hypoglycemic, hypolipidemic, antioxidant, anti-inflammatory, and pro-platelet aggregation activities. The therapeutic potentials of C. striatus were demonstrated to be associated with the presence of high content essential amino acids and good fatty acids known to improve cell growth and facilitate wound healing. Therefore, C. striatus bioactive compounds have great potentials to serve as lead candidates in developing novel therapeutic agents for the management of diabetes and related cardiovascular diseases. This review aims to provide a comprehensive overview of the pharmacological properties and therapeutic potentials of C. striatus for the management of diabetes and associated cardiovascular complications.

In recent years, there has been a growing interest in the preoperative modeling of fluid-structure interaction in the treatment of cerebral aneurysms. In this study, we investigate two cases involving laminar incompressible fluid flow interacting with hyperelastic materials (a vertical flap and aneurysm walls) under the effect of fluid flow. We present a finite element method (FEM) for these prototypical two-dimensional ($2D$) configurations, taking into account the complex flows and deformation of the variant's structure models. We use an Arbitrary Lagrangian-Eulerian (ALE) formulation in a continuum, fully monolithic coupled way, and discretize the fluid and solid domains using the quadratic LBB stable $P_2P_1$ finite element pair to approximate the displacement, velocity, and pressure spaces independently. The resulting discretized form of the nonlinear algebraic system is linearized using a variant of Newton's procedure, and the Jacobian matrices are approximated via the divided difference method. The resulting linear systems are solved using a direct solver MUMPS. We evaluate hydrodynamic forces such as drag and lift coefficients for nonlinear elastic material models, including Saint-Venant Kirchoff, Neo-Hookean, and Mooney-Rivlin (2 parameters) separately. To gain more physical insight into the problem, we verify the computed results by comparing the velocity, viscosity, and pressure fields. Our aim is to qualitatively analyze the changes in the mechanics of the wall behavior of the elasticity of the flap vs. the complexity of deformation, interface, details for prototypical flow situations, corresponding displacement, and deformation. We also provide a physical interpretation of blood flow magnitude and basic hemodynamic phenomena of wall shear stresses (WSS) in aneurysma and the range of deformation. Overall, this study presents a comprehensive approach to modeling fluid-structure interaction in cerebral aneurysms, which could help in the development of more effective treatment strategies.

In this paper, existence and stability results of non-local integro-differential equation with Hilfer derivative of order ω∈(1,2) have been investigated. In this derivative is applied in RLC circuit equation of various fractional order. To proposed problem the existence solutions are derived using Schaefer’s fixed point theorem and the Banach contraction principle is using for uniqueness results. To demonstrate the effectiveness and applicability of our theoretical conclusions and two-step Lagrange polynomial interpolation were used to solve four numerical results.

In this article, we present the use of the coupled land surface model and groundwater flow model SWAT-MODFLOW with the decision support tool WEAP (Water Evaluation and Planning software) to predict future surface water abstraction scenarios in a complex river basin, under conditions of climate change. The modeling framework is applied to the Dee River catchment in Wales, United Kingdom. Regarding hydrology, the coupled model improves overall water balance and low streamflow conditions, compared to a stand-alone SWAT model. The calibrated SWAT-MODFLOW is employed with high resolution climate model data from the UKCP18 project with future scenario of RCP85 from 2020 to 2040. Then, water supply results from SWAT-MODFLOW are fed into WEAP as input for the river reach in the downstream region of the river basin. This system is utilized to create various future scenarios of surface water abstraction of public water supply in the downstream region: maximum licensed withdraw, 50 % authorized abstractions, monthly time series with 1% increase of water use, and maximum water withdraw year based on historical records repeated every year with 1% increase of water use, to estimate the unmet demands and streamflow requirement. This modeling approach can be used in other river basins to manage scenarios of supply and demand.

Blending lignin as the second most abundant polymer in nature with nanostructured compounds such as dendritic polymers will not only add value to lignin, but also increase its application in various fields. In this study, softwood Kraft lignin/polyamidoamine dendritic polymer (PAMAM) blends were fabricated by solution electrospinning method to produce bead-free nanofiber mats. The mats were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), zeta potential, and thermogravimetry analysis (TGA). The chemical intermolecular interactions between lignin functional groups and abundant amino groups in PAMAM were investigated by FTIR and viscosity measurement. These interactions enhanced the mechanical and thermal characteristics of lignin/PAMAM mats, providing further potential applications at industry level.

A subset of patients with schizophrenia experience physio-somatic symptoms reminiscent of chronic fatigue and fibromyalgia. In schizophrenia, these symptoms contribute to impaired quality of life, and are strongly related to neuro-cognitive deficits, and increased IgA responses to tryptophan catabolites. Negative and PHEM (psychosis, hostility, excitation, mannerism) symptoms, psychomotor retardation (PMR) and formal thought disorders, appear to be manifestations of a single trait reflecting overall severity of schizophrenia (OSOS). In this study, 120 patients with deficit schizophrenia (DEFSCZ) and 54 healthy subjects were assessed with the FibroFatigue (FF) rating scale, and the above-mentioned symptom domains as well as neuro-cognitive tests and biomarkers were measured. In DEFSCZ, there were robust associations between the FF score and all above-mentioned symptom domains, and impairments in semantic and episodic memory and executive functions. Furthermore, the FF score loaded highly on an OSOS latent vector (LV), which showed adequate convergent validity, internal consistency reliability and predictive relevance and fitted a reflective model. Soft Independent Modelling of Class Analogy (SIMCA) showed that the FF items discriminated DEFSCZ from controls with an overall accuracy of 100%. Interleukin IL-1β, IL-1 receptor antagonist (sIL-1RA), tumour necrosis factor (TNF)-α and CCL-11 (eotaxin) explained 66.8% of the variance in the FF score and 59.4% of the variance in OSOS. In conclusion, these data show that physio-somatic symptoms are a core component of the phenomenology of DEFSCZ and are largely mediated by neurotoxic effects of activated immune pathways, including aberrations in CCL-11, IL-1β and TNF-α signalling.

Machine learning (ML) has a large capacity to learn and analyze a large volume of data. This study aimed to train different algorithms to discriminate between healthy and pathologic corneal images by evaluating digitally processed spectral-domain optical coherence tomography (SD-OCT) corneal images. A set of 22 SD-OCT images belonging to a random set of corneal pathologies was compared to 71 healthy corneas (control group). A binary classification method was applied; three approaches of ML were used. Once all images were analyzed, representative areas from every digital image were also processed and analyzed for a statistical feature comparison between healthy and pathologic corneas. The best performance was obtained from transfer learning - support vector machine (TL-SVM) (AUROC = 0.94, SPE 88%, SEN 100%) and transfer learning – random forest (TL- RF) method (AUROC = 0.92, SPE 84%, SEN 100%), followed by convolutional neural network (CNN) (AUROC = 0.84, SPE 77%, SEN 91%) and random forest (AUROC = 0.77, SPE 60%, SEN 95%). The highest diagnostic accuracy in classifying corneal images was achieved with the TL-SVM and the TL-RF models. In image classification, CNN was a strong predictor. This pilot experimental study developed a systematic mechanized system to discern pathologic from healthy corneas.

Peste des Petits Ruminants (PPR), a highly contagious viral disease, causes significant economic losses in sheep and goats. Laboratory diagnosis is crucial to disease control and eradication. Since PPRVs have recently adopted new hosts, genetic diversity within isolates of the same lineage is more likely than if they were host-specific, sheep and goats most often. ELISA detects antibodies and antigens in serology. However, mishandling, environmental conditions (temperature and humidity), storage, and sensitivity issues of commercially available ELISA kits prevent rapid PPR virus detection in third-world countries like Pakistan. In the 2020-21 outbreaks in Pakistan, 325 blood samples, 19 swabs, and 6 virus tissue samples of sheep and goats were collected from Gilgit, Islamabad, and Fateh Jang. These virus isolates were submitted to NCBI for partial N gene sequencing. Antigen was prepared from indigenous virus Using semi-purified antigen from PPRV, an indirect ELISA for the detection of PPR antibodies in goat and sheep serum was developed using MW600922 grown in Vero cells. Dilutions of 1:200 serums and 1:32 antigens improve antibody detection. The N-gene-based analysis revealed a better understanding of PPRV genetic characterization. This study develops an RT-PCR assay to detect PPRV by targeting the N-protein gene. This assay offers an accurate and affordable diagnostic tool for PPRV and partial genome sequencing. Results described that PPRV isolates from the current study have 99.73% and 99.4% similarity to previously published Lahore and Faisalabad isolates from Pakistan, respectively. Compared to previous isolates from NCBI data, the virus showed high divergence rates with the Turkish strain. The comparative analysis between Commercial kit (c-ELISA) and I-ELISA revealed that the former had a high sensitivity of 90.60% and specificity of 85.23% compared with the cELISA kit. By comparing I-ELISA and VNT, we find that the current assay is 100% specific and 82.14 % sensitive. Based on these results, serological surveys for PPR antibodies, on a larger scale, in small ruminants can be conducted with indirect ELISA rather than competitive ELISA. Furthermore, the cost and storage efficiency was highly significant because the currently developed method has a low production cost, which is much lesser than the commercially available kit. Our findings demonstrated a significant breakthrough in terms of cost-effectiveness and storage efficiency, and they are highly recommended for developing countries.

A microwave technique prepared a superabsorbent polymer (SAP) by grafting two hydrophilic monomers onto a polysaccharide substrate. The monomers used are acrylic acid (AA) or acrylamide (AM) to graft onto a pullulan substrate (PUL) to form PUL-g- AA (SAP1) and PUL-g- AM (SAP2), respectively. The monomers (AM/AA) graft together onto a PUL substrate to form PUL-g-(AM/AA) (SAP3). Grafting parameters such as grafting efficiency with percentage, conversion of monomer to polymer, gel content, water retention, water adsorption capacity, and swelling kinetics were determined. Additionally, the effect of environmental pH (2, 4, 7, 9, and 12) and sodium dodecylbenzene sulfonate (SDBS) surfactant was evaluated, where SDBS was added by 1,2,3,4 and 5 mM to form (SAP4 to SAP8). FTIR results show that AM grafted on PUL through an aliphatic C-N bond, while AA grafting occurred through a single C-C bond. The grafting efficiency with AM is higher than with AA, as well as their gel contents. Water absorbance capacity increased with grafting of AA or AM separately, and water retention was enhanced. The highest absorbent capacity, water retention, gel content, and grafting parameters values were obtained with 3 mM SDBS content and pH7. The swelling kinetics showed that the increases in the theoretical and experimental swelling equilibriums were 72 % and 82%, respectively, at SAP6 compared to the values of these parameters in SAP3. The water absorption capacity of the hydrogel increases with increasing pH to 7 and then gradually decreases. XRD improves the crystallinity and crystalline size of the hydrogel after grafting polymerization for AM/AA into PUL, in addition to enhancing thermal stability. On the contrary, FE-SEM demonstrated that SDBS improves the porosity and pore size of the hydrogel surface in SAP6.

Background: Methadone is a centrally-acting synthetic opioid analgesic widely used in the methadone maintenance therapy (MMT) programs throughout the world. Considering its neurotoxic effects particularly on the cerebellum, this study aims to address the behavioral and histological alterations in the cerebellar cortex associated with methadone administration. Materials and Methods: Twenty-four adult male albino rats were randomized into two groups of control and methadone treatment. Methadone was subcutaneously administered (2.5–10 mg/kg) once a day for two consecutive weeks. The functional and structural changes in the cerebellum were compared to the control group. Results: Our data revealed that treating rats with methadone not only induced cerebellar atrophy, but also prompted the actuation of microgliosis, astrogliosis, and apoptotic biomarkers. We further demonstrated that treating rats with methadone increased complexity of astrocyte processes and decreased complexity of microglia processes. Our result showed that methadone impaired motor coordination and locomotor performance and neuromuscular activity. Additionally, relative gene expression of TNF-α, caspase-3 and RIPK3 increased significantly due to methadone. Conclusions: Our findings suggest that methadone administration has a neurodegenerative effect on the cerebellar cortex via dysregulation of microgliosis, astrogliosis, apoptosis, and neuro-inflammation.

Family Phyllanthaceae is one of the largest segregates of the eudicot order Malpighiales and its species are herb, shrub, and tree, which are mostly distributed in tropical regions. Certain taxonomic discrepancies exist at genus and family level. Here, we report chloroplast genomes of three Phyllanthaceae species—Phyllanthus emblica, Flueggea virosa, and Leptopus cordifolius— and compare them with six others previously reported Phyllanthaceae chloroplast genomes. The species of Phyllanthaceae displayed quadripartite structure, comprising inverted repeat regions (IRa and IRb) that separate large single copy (LSC) and small single copy (SSC) regions. The length of complete chloroplast genome ranged from 154,707 bp to 161,093 bp; LSC from 83,627 bp to 89,932 bp; IRs from 23,921 bp to 27,128 bp; and SSC from 17,424 bp to 19,441 bp. Chloroplast genomes contained 111 to 112 unique genes, including 77 to 78 protein-coding, 30 transfer RNA (tRNA), and 4 ribosomal RNA (rRNA) that showed similarities in arrangement. The number of protein-coding genes varied due to deletion/pseudogenization of rps16 genes in Baccaurea ramiflora and Leptopus cordifolius. High variability was seen in number of oligonucleotide repeats while analysis of guanine-cytosine (GC) content, codon usage, amino acid frequency, simple sequence repeats analysis, synonymous and non-synonymous substitutions, and transition and transversion substitutions showed similarities in all Phyllanthaceae species. We detected a higher number of transition substitutions in the coding sequences than non-coding sequences. Moreover, the high number of transition substitutions was determined among the distantly related species in comparison to closely related species. Phylogenetic analysis shows the polyphyletic nature of the genus Phyllanthus which requires further verification. We also determined suitable polymorphic coding genes, including rpl22, ycf1, matK, ndhF, and rps15 which may be helpful for the reconstruction of the high-resolution phylogenetic tree of the family Phyllanthaceae using a large number of species in the future. Overall, the current study provides insight into chloroplast genome evolution in Phyllanthaceae.

Digital Image Correlation (DIC) is an optical technique used to measure surface displacements and strains in materials and structures. This technique has demonstrated significant utility in structural examination and monitoring. This manuscript offers a comprehensive review of contemporary research and applications that have leveraged the DIC technique in laboratory-based structural tests. The reviewed works encompass a broad spectrum of structural components, such as concrete beams, columns, pillars, masonry walls, infills, composite materials, structural joints, steel beams, slabs, and other structural elements. These investigations have underscored the efficacy of DIC as a metrological instrument for precise quantification of surface deformation and strain in these structural components. Moreover, the constraints of the DIC technique have been highlighted, especially in scenarios involving extensive or complex test configurations. Notwithstanding these constraints, the DIC methodology has validated its effectiveness as a strain measurement instrument, offering numerous benefits such as non-invasive operation, full-field measurement capability, high precision, real-time surveillance, and compatibility with integration into other measurement instruments and methodologies.

Advancements in technology have revolutionized communication on social media platforms, where reviews and comments greatly influence product selection. Current opinion mining methods predominantly focus on textual content, overlooking the rich information within customer-posted images, termed here as Multus-Medium. This research introduces an innovative deep learning approach, Multus Medium Opinion Mining (MMOM), capitalizing on both text and image data for comprehensive product review analysis. MMOM employs an integrated model of Bidirectional Long Short-Term Memory (BiLSTM) and embedded Convolutional Neural Network (CNN), incorporating architectures of GoogleNet and VGGNet, thus enabling efficient extraction and fusion of textual and visual features. This synergistic approach enables data collection, preprocessing, feature extraction, fusion strategy-based feature vector generation, and subsequent product recommendation. Performance evaluation on two diverse real-world datasets name as “flicker8k” and “t4sa”. These datasets show substantial improvement over existing methods. MMOM outperforms standard benchmark models, achieving an accuracy, F1 score and ROC over fliker8k are 90.38%, 88.75% and 93.08%, whereas for twitter dataset are 88.54%, 86.34%, and 92.26% respectively, the accuracy of purposed model is 7.34% and 9.54% higher than the other two mentioned techniques. These statistics highlight the robustness and applicability of MMOM across various domains. The compelling results underscore the potential of MMOM, providing a more holistic and precise approach to opinion mining in the era of social media product reviews. This research, product recommendation helps the customer to make purchasing decision. Last but not the least, the purposed scheme can further be expanded in any other sentiment task like hospital recommendation system, crop farming recommendation and medical diagnostic system etc.

Background: Aberrations in endothelial cells, immune and oxidative pathways are associated with atherosclerosis (ATS) and unstable angina (UA). The role of trace elements, minerals, and the endogenous opioid system (EOS) in UA are less well established. Methods: We measured lipid, insulin resistance (IR), and immune, trace element (copper and zinc), mineral (magnesium, calcium), EOS (β-endorphin and mu-opioid receptor (MOR)) and antioxidant (vitamin D3) biomarkers in patients with ATS (n=60) and UA (n=60) and healthy controls (n=58). Results: ATS patients showed increased atherogenic and IR indices, IL-6, IL-10, β-endorphin, copper and magnesium, and lower zinc than healthy controls. Logistic regression showed that UA was significantly discriminated from ATS without UA with an accuracy of 85.5% using calcium, IL-10, β-endorphin, MOR, triglycerides, IR (all positively), and copper and vitamin D3 (inversely). Neural networks showed that UA was discriminated from ATS without UA with an area under the ROC curve of 0.942 using MOR, β-endorphin, calcium, insulin resistance, vitamin D3 and copper as input variables. We found that 50.0% of the variance in IR was explained by the regression on copper, IL-10, IL-6 (all positively), and zinc (inversely), while 32.9% of the variance in the atherogenic index of plasma was explained by copper, IL-10 (both positively), and magnesium (inversely). Conclusion: UA is not only mediated by insulin resistance, atherogenicity, and immune disorders, but also by aberrations in the endogenous opioid system and trace elements as well as lowered antioxidant levels. Copper appears to play a key role in IR and atherogenicity.

High pressure crystallization technique has been successfully used to prepare an elusive form II of a non-steroidal anti-inflammatory drug, Mefenamic acid. Single crystal of form II was grown at 0.3 GPa from an 4:1 methanol/ ethanol mixture as a solvent using Diamond Anvil Cell. Comparison of crystal structures show that the efficient packing of MA molecules in Form II results from the structural flexibility of MA acid molecules. Compression studies performed on the single crystal of form I resulted in 14 % decrease of unit cell volume up to 2.5 GPa. No phase transition was observed up to this pressure. A reconstructive phase transition is required to induce conformational changes in the structure, which is confirmed by crystallization at high pressure results.

A hemostatic sponge prototype was successfully synthesized from fish gelatin as an alternative to mammalian gelatin, which was mixed with alginate in certain combinations and double cross-linking of calcium ions and gamma irradiation at a dose of 20 kGy to improve the characteristics and effectiveness of its function as a local hemostatic agent. There was an improvement in the physicochemical and mechanical properties, porosity index, absorption capacity, biodegradation properties, biocompatibility, and hemocompatibility of the FGAS prototypes compared with the pure fish gelatin sponge. Hemostatic activity tests showed that the means of clotting time, prothrombin time, and activated partial thromboplastin time were shorter in the FGAS prototype than in the negative control, and there was no significant difference compared with the commercial gelatin sponge. The hemostatic mechanism of the FGAS prototype combined a passive mechanism as a concentrator factor and an active mechanism through the release of calcium ions as a coagulation factor in the coagulation cascade process.

This study aims to assess food security status of rural, peri-urban and urban households and role of socio-economic factors in ensuring food security. A survey was conducted to collect primary (quantitative) data from 630 respondents using proportionate sampling technique from Punjab, Pakistan. Cronbach’s Alpha reveals stability (>0.75) of data scale items. Using Dietary Intake Assessment (DIA), findings reveal urban households as highly food-secure whereas rural household as most vulnerable to food security at 2450kcal/day per person. Study indicates food price increase as the leading factor in preventing food security among households. Contrary, study identifies risk factors associated to food quality under the abundant availability and access as the new dimension to household food insecurity. Further, results of binary logit model show that socio-economic factors such as monthly income, total number of earners, education of household head and access to market are positively related with food security status whereas, social isolation, volatility in food prices and risk factors in food quality are negatively related with household food security. Therefore, study proposes educational orientation and entrepreneurial development as sustainable solution to ensure food security among masses. Besides, further country level researches are advised to deep delve the mounting menace of food security.

This paper investigates the photocatalytic characteristics of Ag Nanowire (AgNW)/TiO2 and AgNW/TiO2/Graphene oxide (GO) nanocomposites. Samples were synthesized by the direct coating of TiO2 particles on the surface of silver nanowires. As-prepared AgNW/TiO2 and AgNW/TiO2/GO nanocomposites were characterized by electron microscopy, X-ray diffraction, UV/visible absorption spectroscopy, and infrared spectroscopy. Transmission electron microscope (TEM) images confirmed the successful deposition of TiO2 nanoparticles on the surface of AgNWs. The photocatalytic activity of synthesized nanocomposites was evaluated using Rhodamine B (RhB) in an aqueous solution as the model organic dye. Results showed that synthesized AgNW/TiO2/GO nanocomposite has superior photocatalytic activities when it comes to the decomposition of RhB.

The main goal of this paper is to study the weak gravitational lensing by Horndeski black hole in weak field approximation. In order to do so, we exploit the Gibbons-Werner method to the optical geometry of Horndeski black hole and implement the Gauss-Bonnet theorem to accomplish the deflection angle of light in weak field region. Furthermore, we have endeavored to extend the scale of our work by comprising the impact of plasma medium on the deflection angle as properly. Later, the graphical influence of the deflection angle of photon on Horndeski black hole in plasma and non-plasma medium is examined.

The principal objective of this project is to investigate the gravitational lensing by asymptotically flat black holes in the framework of Horndeski theory in weak field limits. To achieve this objective, we utilize the Gauss-Bonnet theorem to the optical geometry of asymptotically flat black holes and applying the Gibbons-Werner technique to achieve the deflection angle of photons in weak field limits. Subsequently, we manifest the influence of plasma medium on deflection of photons by asymptotically flat black holes in the context of Horndeski theory. We also examine the graphical impact of deflection angle on asymptotically flat black holes in the background of Horndeski theory in plasma as well as non-plasma medium.

Necrotizing pneumonia due to Methicillin-Resistant Staphylococcus Aureus (MRSA) is devastating and difficult to treat in preterm infants. We report a case of severe MRSA necrotizing pneumonia in a preterm infant. As an add-on rescue therapy to vancomycin, linezolid rapidly cured this case after the failure of vancomycin plus rifampicin. This rapid cure suggests that adjunctive rather than rescue linezolid may be considered in such cases.

This study tries to focusing on applying information communication technology for economic importance of Mid Oil Company (MDOC), which is among contemporary oil companies in Iraq. Since ICT forms a significant aspect of achieving organizational economic objectives, most of public and private bodies seek to utilize ICT tool and techniques to improve work efficiencies. The emerging growth in ICT has made it process and service automation possible in managing organizational activities. To determine this effect of ICT on organizations, this study formulated statistical research model at MDOC through using fifteen questionnaires, which were distributed on three axes. The outcome of the questionnaire analysis revealed that there is inadequate comprehensive infrastructure to suitably support ICT within the selected organization management. In addition, it revealed that there are no ideal standards to maintain and sustain internet networks. Based on these revelations, the study presents recommendation for the adoption of ICT with the aim of minimizing cost, enhancing communication and managing infrastructure. Also recommends the need to support IT department within an organization, with essential equipment, in terms of man and machine, for better efficiency to employ the key of ICT Impact in Iraqi governmental oil companies.

Heavy metals toxicity is a grave environmental issue in contemporary times. Phytoremediation is economic, effective and ecofriendly approach to decontaminate and remediate metal contaminated areas. Phenolic and Flavonoid content are important abiotic stress markers. The individual and combined impacts of toxiferous metals Arsenic (As), Cadmium (Cd) and (Copper) Cu were employed in recent studies to investigate their effect on Total flavonoids content (TFC) and total phenolic content (TPC) in various parts of Hydrocotyle umbellata L. to explore the role of plant in abating metal contamination. Folin- ciocalteu and AlCl 3 methods were used for investigating TPC and TFC respectively. Two-way ANOVA and CART model were employed for statistical analysis. Highest TPC was examined in decreasing order as leaf & gt; stem & gt; root in case of all the metals. Whereas highest TFC was found in all plant parts when subjected to As toxicity, and the lowest TFC was found in stem of the plant in respect to Cu toxicity. There was significant effect on TPC on plant part when subjected to Cu and As stress, but so significance was observed in plant part in case of Cd and combined metal stress. Treatment concentration had no significant effect on TPC when subjected to unique impact of all the three metals but had significant effect in case of combined metal stress. Similarly, in case of TFC no significant effect was recorded in case of plant part in all the stress types. But treatment amount has significant impact on Cd and combined metal stress. Metal type has significant effect on TPC and TFC. Whereas plant part has significant impact on TPC but non-significant values were observed on TFC in this case. This study epitomizes TPC and TFC in plants as effective and viable tool to pertain their role in phytoremediation against metal contamination. Therefore H. umbellata L. can be exerted for successful assemblage and decontamination of Cd, Cu and As in different plant parts.

Load variations in any power system result in losses escalation and voltage drops. With the sensible and optimal allocation of distributed generators (DGs), these problems could be considerably mitigated. It has been seen in the priorly existing methods that ideally allocation of DGs has been carried out during fixed loads and constant power requirements. However, in real scenarios the loads are always variable and allocation of DGs must be done in accordance to the variations of the connected load. Therefore, the current paper addressed the aforementioned problem by distinctive optimal allocation of DGs for each variability of 24hour load horizon. However, the single exclusive solution is considered among all allocations of 24 hours. The min-max regret concept has been utilized in order to deal with such methodology. Altogether, 24 scenarios are analyzed wherein each scenario corresponds to a specific hour of the respective day. The optimal allocation of DGs in terms of their optimal sizing and placement has been carried out by using three algorithms including battle royal optimization (BRO), accelerated particle swarm optimization (APSO) and genetic algorithm (GA). The multi-objective optimization problem is evaluated on the basis of minimum value criterion of the multi-objective index (MO). MO comprises of active and reactive power losses and voltage deviation. Hence, in order to find robustness of proposed technique, Conseil international des grands réseaux electriques (CIGRE’s) MV benchmark model incorporating 14 buses has been considerably used as a test network. In the end the results of three proposed algorithms have been compared.

Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

Self-driving vehicles demand efficient and reliable depth sensing technologies. Lidar, with its capacity for long-distance, high-precision measurement, is a crucial component in this pursuit. However, conventional mechanical scanning implementations suffer from reliability, cost, and frame rate limitations. Solid-state lidar solutions have emerged as a promising alternative, but the vast amount of photon data processed and stored using conventional direct time-of-flight (dToF) prevents long-distance sensing unless power-intensive partial histogram approaches are used. In this paper, we introduce a groundbreaking ‘guided’ dToF approach, harnessing external guidance from other onboard sensors to narrow down the depth search space for a power and data-efficient solution. This approach centers around a dToF sensor in-which the exposed time widow of independent pixels can be dynamically adjusted. We utilize a 64-by-32 macropixel dToF sensor and a pair of vision cameras to provide the guiding depth estimates. Our demonstrator captures a dynamic outdoor scene at 3 fps with distances up 75 m. Compared to a conventional full histogram approach, on-chip data is reduced by over 25 times, while the total laser cycles in each frame are reduced by at least 6 times compared to any partial histogram approach. The capability of guided dToF to mitigate multipath reflections is also demonstrated. For self-driving vehicles where a wealth of sensor data is already available, guided dToF opens new possibilities for efficient solid-state lidar.

In this paper, we discuss the weak gravitational lensing in the context of stringy black holes. Initially, we examine the deflection angle of photon by charged stringy black hole. For this desire, we compute the Gaussian optical curvature and implement the Gauss-Bonnet theorem to investigate the deflection angle for spherically balanced spacetime of stringy black hole. We also analyze the influence of plasma medium in the weak gravitational lensing for stringy black hole. Moreover, the graphical impact of coupling constant $\alpha$, impact parameter $b$ , black hole charge $Q$ on deflection angle by charged stringy black hole has been studied in plasma as well as non-plasma medium.

Salmonella enterica includes enteric pathogens of zoonotic potential, possessing one of the largest pools of temperate phages in their genomes. One such class of phages previously called Podoviridae (Now genera placed directly under class Caudoviricetes temporarily) is the largest group of temperate phages that lysogenize clinically and economically important Salmonella enterica serovars. These phages are capable of generalized transduction and are well known for carrying foreign DNA (mobile genetic elements and resistance genes) to new bacterial species that play a major role in the evolution, pathogenicity, and host adaptability of Salmonella serovars. Here we report a novel species of podo viruses; Salmonella phage BIS08P22 (BIS08) that infects Salmonella enterica serovar Typhimurium strain SE-BS17 (Acc. NO: MZ503545). Phage BIS08 was viable only at biological pH and temperature (pH7 and 37 °C) and features 41,574 -base pair (bp) linear ds DNA genome with 47% GC content. It encodes 73 putative Open Reading Frames (ORFs), has a mosaic arrangement, and shares only 16 core genes with its closest homologs. BIS08 genome possesses only 52 % homology (genome-wide Nucleotide homology by VIRIDIC analysis) with members of the genus Lederbergvirus which is not sufficient to place it in the same genus. This phage has a unique terminase enzyme (DNA packaging motor) with no nucleotide and protein homology with any known member of the Lederbergvirus genus. We carried out a detailed phylogenetic and genome analysis of this novel phage and proposed its placement in a new genus. Our study also suggests a revision in the classification of the genus Lederbergvirus. We also performed in silico structural analysis of the BIS08 unique terminase enzyme comparing it to its close homologs.

A new class of tetrasubstituted imidazole based compounds was synthesized using a multicomponent one-pot synthesis scheme through a cyclo condensation reaction of benzil, aromatic primary amines, aldehydes and ammonium acetate in glacial acetic acid. The synthesized compounds have been analyzed and characterized by melting point, color, conductivity method, CHN analysis, FT-IR, and UV-Visible. The reaction proceeding was examined by TLC after regular intervals of period. To test biological activity, the synthesized compounds have been examined against various bacterial strains. From the analysis of the antibacterial activity of these synthesized compounds demonstrated that all three imidazole compounds have considerable to significant activity against the strains, and compound K2 was found potent comparatively.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

Objective: A previous study showed that schizophrenia is accompanied by lowered levels of trace/metal elements including cesium. There are no data whether changes in cesium, rubidium and rhenium are associated with activated immune-inflammatory pathways, cognitive impairments, and the symptomatology of schizophrenia. Methods: This study measured cesium, rubidium, and rhenium, cognitive impairments (using the Brief Assessment of Cognition in Schizophrenia) and the cytokines/chemokines interleukin (IL)-1β, tumor necrosis factor (TNF)-α, and CCL11 (eotaxin) in 120 schizophrenia patients and 54 healthy controls. Severity of illness was assessed using the Brief Psychiatric Rating Scale (BPRS), the Scale for the Assessment of Negative Symptoms (SANS), the Fibromyalgia and Chronic Fatigue Syndrome Rating (FF) Scale and the Hamilton Depression Rating Scale (HAM-D). Results: Serum cesium was significantly lower in schizophrenia patients as compared with controls. Serum cesium was significantly and inversely associated with CCL11 and TNF-α, but not IL-1β. Moreover, there were significant inverse associations between serum cesium levels and the BPRS, FF, HAM-D and SANS scores and positive correlations between cesium and neurocognitive probe results including the Tower of London, Symbol Coding, Controlled Word Association, Category Instances, Digit Sequencing Task, and List Learning tests. Conclusion: The results suggest that lowered serum cesium levels may play a role in the pathophysiology of SCZ, specific symptom domains including negative, depressive and fatigue symptoms, neurocognitive impairments (spatial working, episodic and semantic memory and executive functions) and neuro-immune pathways as well.