Background: This systematic umbrella review aims to investigate whether provide an analysis of guidelines regarding the treatment of diverticular abscesses summarizing the evidences from the best available practice. Material and methods: A systematic literature search was performed until using the Cochrane Overviews of Reviews model for search the ‘Clinical Practice Guidelines’; at the end of initial search only 12 guidelines, whose characteristics are reported in the following table were included in this analysis. The quality of the guidelines was assessed by adopting the 2017 updated version of the “Appraisal of Guidelines for Research and Evaluation II” (AGREE II). The comparative analysis of these guidelines has highlighted the presence of some differences regarding the recommendations on the treatment of diverticular abscesses. In particular, there are some controversies about the diameter of abscess to be used in order to decide between medical treatment and percutaneous drainage. Different guidelines propose different abscess diameter cutoffs, such as 3 cm, 4-5 cm, or 4 cm, for distinguishing between small and large abscesses. Conclusions: Currently, a lot of scientific societies recommend that diverticular abscesses with diameters larger than 3 cm should be considered for percutaneous drainage whereas abscesses with diameters smaller than 3 cm could be appropriately treated by medical therapy with antibiotics; only, few guidelines, suggest the use of percutaneous drainage for abscess with a diameter greater than 4 cm .The difference among guidelines is the consequence of the different selection of scientific evidences. In conclusion, our evaluation has revealed the importance of seeking new scientific evidence with higher quality to either confirm, reinforce or potentially weaken the existing recommendations from different societies.

The aim of this study was to measure the effects on 3D active cervical Range of Motion (ACROM) and perceived pain of a n elastic taping (ET) application in the cervical area. Thirty participants (n: 22M and 8F, age 35.4±4.4 years; body height 173.1±8.4 cm; body mass 73.5±12.8 kg) for the study group (SG) and twenty subjects (n: 11M and 9F, age 32.6±3.9 years; body height 174.9±10.9 cm; body mass 71.2±12.9 kg) for the control group (CG) were recruited. All subjects were symptomatic for neck and cervical pain in baseline condition. Each group performed on ACROM test and the perceived pain on neck basing as Numerical Rating Scale (NRS 0-10, a.u.): at the baseline (T0); after 20' from ET application (T1); after three days of wearing the ET application (T2). Between T0 and T1 an ET was applied on the cervical area of the SG participants. Statistical analysis did not show any significant change in CG in any measurement session for ACROM and neck pain parameters. Conversely, the SG showed significant improvements for ACROM rotation left (T0 64.8 ± 7.7° - T2 76.0 ± 11.1° p < 0.000) and right (T0 66.0 ± 11.9° - T2 74.2 ± 9.6° p < 0.000); lateral inclination left (T0 37.5 ± 6.9° - T2 40.6 ± 10.8° p < 0.000) and right (T0 36.5 ± 7.9° - T2 40.9 ± 5.2° p < 0.000); flexion posterior (T0 47.0 ± 12.9° - T2 55.1 ± 12.3° p < 0.001) and anterior (T0 55.0 ± 3.6° - T2 62.9 ± 12.0° p < 0.006). A significant decrease was measure also in SG for pain NRS between T0 and T2 (T0 7.5 ± 1.0° - T1 5.5 ± 1.4 - T2 1.4 ± 1.5° p < 0.000). In conclusion, the results of this study underline the usefulness of a bilateral and symmetrical ET cervical application in terms to enhance multiplanar ACROM and to reduce subjective self-perceived cervical pain when it is needed. These findings can be applied for managing musculoskeletal health of different kind of individuals.

Rheumatoid arthritis (RA) is a chronic inflammatory disease. Despite new methods of diagnostics and treatment as well as extensive biological and immunosuppressive treatment, the etiology of RA is not fully understood. Moreover, the problem of diagnosis and treatment of RA patients is still current and affects a large group of patients. It is suggested that these ER-related features may impair adaptation to chronic stress, inferring the risk of rheumatoid arthritis. The main goal in this study was evaluation of changes in mRNA translation to determine chronic ER stress conditions in rheumatoid arthritis patients. The study group consist of 86 individuals including total 56 rheumatoid arthritis patients and 30 healthy controls. The expression level of mRNA form blood samples of RA patients as well as controls of the PERK-UPR associated genes: p-eIF2, BCL-2, PERK, ATF4, BAX were investigated by Real-Time qPCR. GAPDH expression was used as a standard control. Considering the median, the expression of PERK, BCL-2, p-eIF2, ATF4, BAX was found to be significantly increased in the blood of RA patients compared with the control group. The p-value for the PERK gene was 0.0000000036, the p-value for the BCL-2 gene was 0.000000014, the p-value for the p-eIF2 gene was 0.006948, the p-value for the ATF4 gene was 0.0000056 and the p-value for the BAX gene was 0.00019, respectively. Thus, it can be concluded that targeting of the components of the PERK-dependent UPR signaling pathway via small-molecule PERK inhibitors, may contribute to the development of novel, innovative treatment strategies against rheumatoid arthritis.

Autoimmune Glomerulonephritis represents a homogeneous area of renal pathology with clinical relevance for either the numerical impact or difficulties in treatment. SLE and Lupus nephritis are the most frequent occurrences. They are characterized by glomerular deposition of circulating autoantibodies that recognize glomerular antigens Technologies for studying tissue and circulating antibodies have evolved over the years and culminated with the direct analysis of the antigen-antibody complex in renal bioptic fragments. Mass-spectrometry of immunoprecipitates from the renal tissue is, in fact, the most recent evolution that eliminates the need for tissue microdissection. The results obtained with this technique have led to the discovery of several new glomerular antigens in Membranous Nephropathy and in Lupus Nephritis, two conditions whose pathogenesis remained unknown for decades, Peptide and protein arrays (Immunopeptidomics and immunoproteomics, respectively) for the characterization of circulating autoantibodies represent the new frontier for identifying autoantibodies. Immunopeptidomics consists in 7.5 million aligned peptides of 16 amino acids each which cover the whole human proteome; immunoproteomics utilizes a chip containing structured proteins, 26.000 overall. Both are very sensitive techniques that allow the characterization of hundreds of new antibodies in circulation. The contribution of arrays to amplify the panel of potential autoantibodies involved in glomerulonephritis is expected to be relevant for improving our knowledge of the pathogenesis of several autoimmune conditions.

The reactive nature of traditional frequency stability methods can lead to delayed corrective actions and unnecessary loss-of-load. This work presents a distributed model predictive control method for proactive power system frequency stability. Dynamic state estimation model is derived through a particle filter. By being able to estimate the future state of frequency, corrective actions can be taken before the system reaches a critical condition. Proactive approach makes it possible to optimize the response to a disturbance, which results in a decrease of the amount of compensation utilized. The method is tested via Matlab simulations based on Kundur's Two-Area System, and the IEEE 14-Bus system. Performance metrics are provided and evaluated against other contemporary solutions found in literature. Easy-to-derive model, without hard-to-design parameters, indicate potential towards real-life applications.

Coronavirus 19 disease (COVID-19) may be complicated by thrombotic events, particularly venous thromboembolism (VTE), which have been reported both in critically ill hospitalized patients and in individuals with mild symptoms. It is known that the chronic use of oral contraceptive pills (OCPs) is associated with higher risk of VTE. To date, there are only few reports concerning the association of OCPs and VTE/pulmonary embolism (PE) in COVID-19 patients. Given that during the convalescent phase of disease, a state of endothelial dysfunction, hypercoagulability and a low-grade inflammation may be persistent, the occurrence of thromboembolic events following acute COVID-19 infection may be not surprising. Herein, we report a case of high-risk PE detected in a post-COVID-19 young woman under hormonal contraception, which required thrombolytic treatment. A number of prothrombotic phenomena, such as overweight, hormonal contraceptive therapy, recent COVID-19 infection and prolonged immobilization, might have synergically contributed to the development of a sublethal thromboembolic event.

Anatomy education plays a critical role in medical practice, and the level of anatomical knowledge among students and physicians significantly impacts patient care. This article presents a pilot project conducted by the University of Milan aimed at exploring the effectiveness of the Area9's Rhapsode platform, an intelligent tutoring system that uses artificial intelligence to personalize learning and collect data on mastery acquisition. The study focused on liver anatomy and employed a flipped classroom approach, incorporating adaptive learning modules and an interactive in-class session. The project's execution, outcomes and preliminary pedagogical considerations are discussed. The results demonstrated improved learning quality, positive repurposing of study time, enhanced metacognitive awareness among students, with most of students demonstrating conscious mastery of the materials and a clear understanding of their level of competence. This approach, by providing valuable insights into the potential of artificial intelligence-based adaptive learning systems in anatomy education, could address the challenges posed by limited teaching hours, shortage of anatomist and the need for individualized instruction, with recommendations for future research and the expansion of adaptive learning modules to other anatomical districts.

Background: Diabetes mellitus (DM) and osteoporosis are two of the most widespread metabolic disease in the world. The aim of this study is to investigate the prevalence of DM among patients affected by osteoporosis and fragility fractures, and to search differences in clinical features. Methods: 713 patients belonging to CTO Bone Unit because of osteoporosis and fragility fractures were divided into two groups, according to the diagnosis of DM. The clinical and bone characteristics of patients were compared. Results: Prevalence of DM was 10.8%. When compared to patients without DM, the median age at the time of first fracture was similar (72 years ± 14 IQR vs 71 years ± 12 IQR); prevalence of combination of vertebral and hip fractures was higher (p=0.039), as well as prevalence of males, although not significantly (p=0.051). Bone mineral density (BMD) at all sites was higher in DM group; Trabecular Bone Score (TBS), instead, was significantly lower (p<0.001). Conclusions: Patients with fragility fractures and DM more frequently show combination of major fractures with higher BMD levels. In these patients, TBS could be a better indicator of bone health than BMD and therefore should be used as a diagnostic tool in clinical practice.

In numerous instances, the fate of a single cell not only represents its peculiar outcome but also contributes to the overall status of an organism. In turn, cell division cycle and its control strongly influence cell destiny playing a critical role in targeting it towards a specific phenotype. Several factors participate to the control of growth and among them p27 and p57, two proteins modulating various transitions of cell cycle, appear to play key functions. In this review, the major features of p27 and p57 will be described, focusing in particular on their recently identified roles not directly correlated to cell cycle modulation. Then, their possible role as molecular effectors of polyphenols activities are discussed. Polyphenols represent a large family of natural bioactive molecules that have been demonstrated to play promising protective activities against several human diseases. Their use has also been proposed in association with classical therapies for ameliorating their clinical effects and for diminishing their negative side activities. The importance of p27 and p57 in polyphenol cellular effects will be discussed with the aim of identifying novel therapeutic strategies for the treatment of important human diseases, such as cancers, characterized by an altered control of growth.

Due to the rapid emergence of multi drug resistant (MDR) pathogens against which current an-tibiotics are no longer functioning, severe infections are becoming practically untreatable. Con-sequently, the discovering of new classes of effective antimicrobial agents with novel modes of action is becoming increasingly urgent. The bioactivity of Cannabis sativa, an herbaceous plant used for millennia for medicinal and recreational purposes, is mainly due to its content in phytocan-nabinoids (PCs). Among the 180 PCs detected, cannabidiol (CBD), Δ8 and Δ9-tetrahydrocannabinols (Δ8-THC and Δ9-THC), cannabichromene (CBC), cannabigerol (CBG), cannabinol (CBN) and some their acidic precursors have demonstrated from moderate to potent antibacterial effects against Gram-positive bacteria (MICs 0.5–8 µg/mL), including methicillin-resistant Staphylococcus aureus (MRSA), epidemic MRSA (EMRSA), as well as fluoroquinolones and tetracycline-resistant strains. Particularly, the not psychotropic CBG was also capable to inhibit MRSA biofilm formation, to eradicate that mature, and to rapidly exterminate MRSA persiters cells. On this scenario, CBG, as well as other minor not psychotropic PCs, such as CBD, and CBC could represent promising compounds for developing novel antibiotics with high therapeutic potential. Anyway, further studies are necessary, needing abundant quantities of such PCs, scarcely provided naturally by Cannabis plants. Here, after an extensive overture on cannabinoids including their reported an-timicrobial effects, aiming at easing the synthetic production of the necessary amounts of CBG, CBC and CBD for further studies, we have, for the first time, systematically reviewed the synthetic pathways utilized for their synthesis, reporting both reaction schemes and experimental details.

Mangroves play an important role as a carbon sink and in mitigation of climate change. This study aimed to assess the anthropogenic activities, water and soil quality, mangrove diversity, and carbon sequestration potential of mangrove trees in the Kaingen River, Kawit, Cavite. The sampling period was conducted from November 2022 to March 2023 with the established three sampling sites. The DENR Administrative Order (DAO)- 2016-08 was used as a standard for water quality parameters, except for phosphates which used DAO-2021-19. The soil parameters were identified using the soil test kit from the Bureau of Soil and Water Management (BSWM) and at the BSWM laboratory. Mangrove species were identified using The Field Guide for Philippine Mangroves and were verified by experts. The carbon sequestration potential was obtained using an allometric equation for Southeast Asian mangroves. There are three mangrove species found in Kaingen Riverine such as Rhizophora mucronata, Avicennia alba, and Xylocarpus granatum. Based on species importance value Rhizophora mucronata is the dominant mangrove species. The result for carbon sequestration of each mangrove species showed that Rhizophora mucronata yielded the highest carbon stored (35.16 tC/ha) and carbon sequestered (128.92 tCO₂/ha). Among all the sampling sites, site 3 yielded the highest carbon stored (30.76 tC/ha) and carbon sequestered (112.81 tCO₂/ha) in Kaingen River. Overall, the results of the study showed that Kaingen River can potentially store carbon at 71.89 tC/ha and CO2 sequestered at 263.62 tCO₂/ha. This urges to practice conservation and protection measures for the mangroves forest of Kaingen River.

Hydration and fluids detected with bioimpdance can be confounderdby ecw expansion and overload. to estimates with sufficient accuracy body fat A confrontation with imaging and dxa is confirmatory

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

Starting from early 2020, the COVID-19 pandemic has caused a morbidity and mortality excess worldwide. Containment strategies rely firstly on rapid and sensitive laboratory diagnosis with molecular detection of the viral genome in respiratory samples being the gold standard. Reliability of diagnostic protocols could be affected by SARS-CoV-2 genetic variability. In fact, mutations occurring during SARS-CoV-2 genomic evolution can involve the regions targeted by the diagnostic probes. Following a review of the literature and an in silico analysis of the most recently described virus variants (including the UK B 1.1.7 and the South Africa 501Y.V2 variants), we conclude that the described genetic variability should have minimal or no effect on the sensitivity of existing diagnostic protocols for SARS-CoV-2 genome detection. However, given the continuous emergence of new variants, the situation should be monitored in the future, and protocols including multiple targets should be preferred.

The demonstration of compliance of rolling stock against disturbance limits for railway signaling, and in particular track circuits, is subject to a large deal of variability, caused by the diverse values of the electrical parameters of the railway line and resulting transfer functions, as well as operating conditions of rolling stock during tests. Instrumental uncertainty is evaluated with a Type B approach and shown to be much less than the experimental variability. Repeated test runs in acceleration, coasting, cruising, braking conditions are considered, deriving both max-hold (spread) and sample dispersion curves compared to the respective mean values (Type A approach to the evaluation of uncertainty). The major source of variability affecting a significant portion of the spectrum is caused by the superposed oscillations of the onboard LC filter, for which different choices of the transformation window duration are discussed. The test runs and the acquired data covered overall 1 day of tests along about 300 km of the Italian 3 kV DC railway network.

The present review compared the efficacy of soft tissue substitutes (STS) and autogenous free gingival graft (FGG) or connective tissue graft (CTG) in mucogingival procedures to increase keratinized tissue (KT) width around teeth and implants. Two independent examiners performed the electronic search on Medline and Cochrane Library based on the following PICO’s format: (P) adult patients; (I) soft tissue substitutes and FGG/CTG; (C) STS vs CTG; STS vs FGG; STS vs CTR; (O) KT width gain; (S) Systematic Reviews, Randomized Controlled Trials. Results showed that around teeth, all biomaterials showed superior performance compared to CAF alone for treating gingival recessions. However, when compared to CTG, ADM yields the most similar outcomes to the gold standard (CTG), even though in multiple recessions CTG still continue to be considered the most favorable approach. Use of STSs (acellular matrix or tissue engineered) in combination with an apically positioned flap resulted in a significantly less gain of KTW compared to what achieved with FGG and APF. Around dental implants, free gingival grafts were deemed more effective than soft tissue substitutes in enhancing keratinized mucosa width.

(1) Background. Intracavitary hyperthermic chemotherapy (HITHOC) remains a part of the complex mosaic which is the multimodal approach in advanced stage thymomas and pleural malignancies, and its role is still widely debated. In recent years, several studies have demonstrated the feasibility and the efficacy of HITHOC combined with cytoreductive surgery in the treatment of thymoma relapses and malignant pleural mesothelioma (MPM). However, there are currently no studies available on pleurectomy/removal of pleural lesions using the robotic technique, in association with intrathoracic chemotherapy. The aim of this narrative review is to evaluate the feasibility and safety of robotic pleurectomy/removal of relapses and HITHOC in patients with pleural recurrence of thymoma or MPM, after having analyzed the literature concerning this controversial topic, and to report our experience with robotic surgery. (2) Methods: A review of papers published on this topic, from 1980, was conducted. Later, the data of consecutive patients affected by thymoma relapses or MPM who underwent robotic surgery in combination with HITHOC will be collected and analyzed. The surgery performed, prior to intrathoracic infusion of the high-temperature chemotherapy, consisted of the removal of the recurrences or pleurectomy, depending on the pathology. All surgeries were performed with a 4-port-fully robotic technique. (3) Results: Between 2017 and 2022, nine patients underwent robotic cytoreductive surgery in combination with HITHOC. No intraoperative complications occurred. One patient had a grade II Clavien-Dindo postoperative complication. Oncological follow-up showed results in line with the literature. (4) Conclusion: With the limitation of the small number of patients, considering the results, robotic surgery may represent the surgical approach of choice, in combination with HITHOC, in patients with pleural relapses of thymoma and early-stage MPM.

Machine Learning (ML) approaches have been fruitfully applied to several classification problems of neurophysiological activity. Considering the relevance of emotion in human cognition and behaviour, ML found an important application field in emotion identification based on neurophysiological activity. Nonetheless, the literature results present a high variability depending on the neuronal activity measurement, the signal features and the classifier type. The present work aims to provide new methodological insight on ML applied to emotion identification based on electrophysiological brain activity. For this reason, we recorded EEG activity while emotional stimuli, high and low arousal (auditory and visual) were provided to a group of healthy participants. Our target signal to classify was the pre-stimulus onset brain activity. Classification performance of three different classifiers (LDA, SVM and kNN) was compared using both spectral and temporal features. Furthermore, we also contrasted the classifiers performance with static and dynamic (time evolving) features. The results show a clear increased in classification accuracy with temporal dynamic features. In particular, the SVM classifiers with temporal features showed the best accuracy (63.8 %) in classifying high vs. low arousal auditory stimuli.

This study explores innovation and sustainability within the Construction, Environment, and Territory (CAT) curriculum in Italian Upper Secondary Schools. It begins with an overview of Education for Sustainable Development (ESD) and its integration at various educational levels, focusing on technical/vocational curricula in Upper Secondary Education. The study examines the evolution of the technician's role, the CAT pathway in the Italian educational system, and comparisons with other European contexts. It analyzes the alignment between skills developed during the CAT course and the professional competencies required by the community and job market. A survey conducted among recent graduates and companies involved in the Pathways for Transversal Skills and Orientation (PCTO) at a CAT-focused school reveals significant training and professional needs related to Sustainable Development. To address these needs, the study proposes integrating ministerial programs in professional disciplines such as Topography, Building and Technological Systems Design, and Geopedology, Economics, and Appraisal, with new modules dedicated to Sustainable Development. These modules are to be integrated into the last three years of the course, utilizing the autonomy and flexibility in curricular planning per-mitted by current regulations. Additionally, the proposal includes actions to redistribute existing educational modules within ministerial programs without increasing teaching hours. An initial step in updating professional discipline programs involves implementing a cross-disciplinary educational path within Civic Education, focusing on Sustainable Mobility. The investigation, evaluation, and educational design process presented in this study aims to serve as a model for swiftly implementing structured curriculum reforms, emphasizing educational innovation and comprehensive student preparation to meet emerging social and professional needs.

Intense physical efforts performed at maximal or near-maximal speeds and the ability to recover among sprint are important characteristics of soccer player. Considering that women's soccer is a markedly growing sport, the aim of the study was to analyse the performance (total time –TT-; fatigue index percentage -IF%) and physiological (aerobic and anaerobic) responses to Repeated Sprint Ability Test (RSA, 7×30 m sprints with 25 s of active recovery among sprints) in an elite female player (age: 30 yrs; BMI: 20.3 kg/m²). A repeated measure MANOVA over the 7 sprints time series was applied (p < 0.05). Results showed that TT was 58.71 s (Ideal Time: 56.98 s) with IF% of 3.0%. Energy contributions were given for 80.3% by aerobic, 19.2% by anaerobic lactid, and 0.5% by anaerobic alactid sources. Considering that 1) we have different kinetics in heart rate (HR) and maximum oxygen uptake with oxygen uptake that reach the peak when HR is still rising, and 2) the energy consumption during intermittent exercises requires different metabolism as a result of physiological stimuli proposed, the present findings substantiate the need to choose specific and adequate training methods for female soccer players that aim at increasing their RSA performances.

Novel drugs profoundly changed the outcomes in CLL patients and traditional prognostic/predictive factors that were delineated in the era of chemo-immunotherapy need to be validated in the contest of these new targeted therapies. Currently, the most important prognostic genetic biomarkers are immunoglobulin heavy chain variable (IGHV) mutational status, genetic aberrations including del(17p)/TP53 abnormalities and the complex karyotype. In this review we discuss the prognostic/predictive role of these genetic markers in relation to novel treatments. Moreover, we present and discuss the new score systems that were elaborated and validated in the era of new drugs. Given the deeper responses obtained with small molecules, new prognostic/predictive markers, including measurable residual disease, and validated prognostic scores could possibly be incorporated into routine prognostic scores, to better identify “very-high” CLL patients, who will need more effective treatments.

Bone tissue engineering has developed significantly in recent years as the increasing demand for bone substitutes due to trauma, cancer, arthritis, and infections. The scaffolds for bone regeneration need to be mechanically stable and have a 3D architecture with interconnected pores. With the advances in additive manufacturing technology, these requirements can be fulfilled by 3D printing scaffolds with controlled geometry and porosity using a low-cost multistep process. The scaffolds, however, must also be bioactive to promote the environment for the cells to regenerate into bone tissue. To determine if a low-cost 3D printing method for bespoke SiOC(N) porous structures can regenerate bone these structures were tested for osteointegration potential by using human mesenchymal stem cells (hMSCs). This includes checking the general biocompatibilities under the osteogenic differentiation environment (cell proliferation and metabolism). Moreover, cell morphology was observed by confocal microscopy and gene expressions on typical osteogenic markers at different stages for bone formation were determined by real-time PCR. The results of the study showed the pore size of the scaffolds had a significant impact on differentiation. A certain range of pore size could stimulate osteogenic differentiation, thus promoting bone regrowth and regeneration.

Background: The ongoing outbreak of Coronavirus Disease 2019 (COVID-19) represents a major threat to human health, which impairs the functionality of several organs. One of the hardest challenges in the fight against COVID-19 is the development of wide-scale, effective, and rapid laboratory tests to control disease severity, progression, and possible sudden worsening. Monitoring patients in real-time is indeed highly demanded in this pandemic era when physicians need reliable and quantitative tools to prioritize patients’ access to intensive care departments. In this regard, salivary biomarkers are extremely promising, as they allow for a fast and non-invasive specimens’ collection, which can be repeated multiple times. Methods: We compare salivary levels of immunoglobulin A subclasses (IgA1 and IgA2) and free-light chains (FLC k and λ) in a cohort of 29 SARS-CoV-2 patients and 21 healthy subjects. Results: We found that each biomarkers differs significantly between the two groups, with p-values ranging from 10-8 to 10-4. The performance ranking of these markers, shows that λFLC level (p=1.4e-8) is the best-suited candidate to discriminate the two groups, with an accuracy of 0.94 (0.87-1.00 95% CI), a precision of 0.91 (0.81-1.00 95% CI), a sensitivity of 1.00 (0.96-1.00 95% CI) and a specificity of 0.86 (0.70-1.00 95% CI). Conclusion: These results suggest λFLC as an ideal indicator of patient conditions. This is more strengthened in consideration that λFLC half-life (approximately 6 hours) is significantly shorter than the IgA one (21 days): thus λFLC appears displaying the potential to effectively monitor patients fluctuation in real-time.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

Ninety percent of the existing building stock in Europe was built before 1990. These buildings are in urgent need for a significant improvement of energy-efficiency through renovation. Regrettably, so far only five percent of renovation projects have been able to yield energy-saving at deep renovation level. State-of-the-art renovation solutions are available, but costly and lengthy renovation processes and incomprehensible technical complexities hinder the achievement of a wide impact at a European scale. This paper presents research on Plug-and-Play (PnP) technologies supported by Building Information Modelling (BIM) to provide affordable, interchangeable and quick-installation solutions to overcome the main barriers of building deep renovation.

In the last decades, the impacts of urbanization on the hydrological cycle have led to an increase in the frequency and magnitude of urban flooding events, also amplified by the effects of climate change. Sustainable Drainage Systems (SuDS) provide a revolutionary change in this field, improving the sustainability and resilience of cities. This research explores the integration of different SuDS with the aim of significantly reducing both flow volume and celerity of floods in a residual urban catchment area of metropolitan city of Querétaro (Mèxico), where extreme rainfall frequently occurs. This catchment is a representative suburb of urban pressure and environmental degradation problems. Currently, managing storm water under climate uncertainty through a multi-disciplinary approach is a major concern in this urban area. A 1D-2D coupling model of shallow water equations, finite volume method, unstructured meshing method, and hybrid parallel computing application defined the optimal configuration of SuDS at catchment scale to reduce the flood vulnerability in Querétaro. Specifically, in this paper we explore the management issues of the proposed SuDS configuration that acts as a water resource system with multiple purposes. A generic simulation model called MODSIM was applied to simulate the designed urban drainage system under a balanced IPCC future climate scenario in terms of reliability, resilience and vulnerability against water scarcity.

Microplastics, pervasive in both terrestrial and aquatic ecosystems, have emerged as significant contributors to greenhouse gas (GHG) emissions, including carbon dioxide (CO2), methane (CH4), and nitrous oxide (N2O). This review synthesizes recent studies from 2022 to 2024, revealing the complex mechanisms through which microplastics influence GHG production. These mechanisms include the adsorption of nutrients and pollutants onto microplastic surfaces and their role as substrates for microbial colonization. The impacts of microplastics vary significantly across different environments, such as agricultural soils and marine sediments. The review underscores the urgent need for standardized methodologies and long-term field studies to accurately assess the ecological consequences of microplastics. Notably, the role of nitrous oxide (N2O), a potent GHG with a global warming potential nearly 300 times that of CO2, remains underexplored in the context of microplastic interactions, highlighting a critical research gap. Additionally, the synergistic effects of microplastics with other pollutants require further investigation to understand their cumulative impact on GHG emissions fully. This review calls for a coordinated effort among researchers and policymakers to advance our understanding of microplastics' role in global GHG budgets and to develop effective strategies for mitigating their environmental and climatic impacts.

The work addresses the problem of Power Quality (PQ) metrics (or indexes) suitable for DC grids, encompassing Low and Medium Voltage applications, including electric transports, all-electric ships and aircrafts, electric vehicles, distributed generation and microgrids, modern data centers, etc. The two main pillars on which such PQ indexes are discussed and built are: i) the physical justification, so the electric phenomena affecting DC grids and components (PV panels, fuel cells, capacitors, batteries, etc.), causing e.g. stress of materials, ageing, distortion, grid instability; ii) the existing standardization framework, pointing out desirable coverage and extension, similarity with AC grids standards, but also inconsistencies. The first point is made more clear and usable by a graphical overview of the discussed phenomena. On this basis PQ is interpreted beyond the usual low-frequency range, including thus supraharmonics and common-mode disturbance, and filling the gap with the Electromagnetic Compatibility domain. However, phenomena typical of EMC and electrical safety (such as various types of overvoltages and fast transients) are excluded. Suitable PQ indexes are then reviewed, suggesting integrations and modifications, to cover the relevant phenomena and technological progress, and to better follow the normative exigencies.

Convolutional Neural Networks (CNNs) present drawbacks for modeling geometric transformations, such as scaling and rotation, caused by the convolution operation’s locality. Deformable convolution (DCON), a mechanism that substitutes standard convolution, increasing the receptive field to capture relevant features, is a promising approach to solve this drawback and improve the robustness of CNNs. However, the optimal way to replace the standard convolution with its deformable counterpart in a CNN model is unclear. In this study, we clarify this aseveration by conducting several experiments using deformable convolutions applied in the layers that conform a small four-layer CNN model. We also use deformable convolutions on the four-layers of several ResNet CNNs with depths 18, 34, 50, and 101. The models were tested in binary balanced classes with 2D data for image classification: Cats &amp; Dogs, EyesPACS, Spyders &amp; Chickens, and Shapes. After this testing, we evaluated DCON in 3D data for action recognition: UCF101 and Human2 (a dataset we compiled to control movement, clothing and background). The contribution of this research lies in a guideline to use DCON. It can be summarized as follows: if DCON is used on the first layers of the proposal of model (with simple features), the computational resources expressed as the quantity of Flops will tend to increase and produce bigger misclassification than the standard CNN. However, if the DCON is used at the end layers, the quantity of Flops used in the training and testing will decrease, and the classification accuracy will improve by up to 20% about the base model. Moreover, it gains robustness when using deformable convolutions because it can adapt to the region of interest. Also, the best kernel size of the DCON is three. It showed better results than size five. In the last case, the quantity of Flops increase quadratically, but their performance does not increase significantly. With these results, we propose a guideline to use the DCON and contribute to understanding the impact of DCON on the robustness of CNNs.

Variable-Angle Tow (VAT) laminates can improve straight fiber composites mechanical properties thanks to the application of curvilinear fibers. This characteristic allows to achieve ambitious objectives for design and performance purposes. Nevertheless, the wider design space and the higher number of parameters result in a more complex structural problem. Among the various approaches that have been used for VATs study, Carrera’s Unified Formulation (CUF) allows to obtain multiple theories within the same framework, guaranteeing a good compromise between the results accuracy and the computational cost. In this article, the linear buckling behavior of VAT laminates is analyzed through the extension of CUF 2D plate models within the Reissner’s Mixed Variational Theorem (RMVT). Results show that RMVT can better approximate the prebuckling non-uniform stress field of the plate when compared to standard approaches, thus improving the prediction of the linear buckling loads of VAT composites.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

Background: In the 2022 National Youth Tobacco Survey disposable e-cigarette devices are shown to be the most widely used e-cigarette devices amongst U.S. youth. In this paper we report the results of research designed to estimate the prevalence of use of BIDI® Stick branded e-cigarettes amongst youth (aged 13 to 17), and under-age young adults (aged 18 to 20) in the U.S. Methods: Cross sectional online survey of a nationally representative sample of 1,215 youth (13 17 years) recruited via the IPSOS probability-based KnowledgePanel and 3,370 young adults aged 18 to 24 - amongst whom 1,125 were aged 18 to 20. Results: Amongst youth aged 13 to 17, 0.91% [95% CI: 0.44-1.68] or 190,000 [95% CI: 90,000-350,000] youth reported having ever used a BIDI® Stick branded product and 0.04% [95% CI: 0.00-0.38] or less than 10,000 youth reported currently using a BIDI® Stick branded product. Amongst those young adults aged 18 to 20, 3.90% [95% CI: 2.49-5.81] or 470,000 [95%CI: 300,000-700,000] reported having ever used a BIDI® Stick product whilst 0.60% [95% CI: 0.17-1.55] or 70,000 [95% CI: 20,000-180,000] reported they now use a BIDI® Stick product “every day” or “some days”. Conclusions: The low prevalence of youth and underage adult current use of the BIDI® Stick e cigarette suggests that this product is not responsible for the recent growth in the use of disposable e-cigarettes by youth within the U.S. as demonstrated by the 2022 National Youth Tobacco Survey.

Smart Living, an increasingly prominent concept, entails incorporating sophisticated technologies in homes and urban environments to elevate the quality of life for citizens. A critical success factor for Smart Living services and applications, from energy management to healthcare and transportation, is the efficacy of human action recognition (HAR). HAR, rooted in computer vision, seeks to identify human actions and activities using visual data and various sensor modalities. This paper extensively reviews the literature on HAR in Smart Living services and applications, amalgamating key contributions and challenges while providing insights into future research directions. The review delves into the essential aspects of Smart Living, the state of the art in HAR, and the potential societal implications of this technology. Moreover, the paper meticulously examines the primary application sectors in Smart Living that stand to gain from HAR, such as smart homes, smart healthcare, and smart cities. By underscoring the significance of the four dimensions of Context Awareness, Data Availability, Personalization, and Privacy in HAR, this paper serves as a valuable resource for researchers and practitioners striving to advance Smart Living services and applications.

The implementation of management systems has become a strategic advantage in achieving business goals, especially in industrial organizations, but the implementation of social responsibility requirements is especially ethical. Large multinational companies have long been developing and, in particular, implementing their own codes of conduct, which include their suppliers, to demonstrate their commitment to Corporate Social Responsibility (CSR). The compliance with CSR requirements from stakeholders is thus extended or intertwined with requirements in established management systems (MSs). The objectives of the study were to (1) analyze the different approaches to CSR in internationally recognized cross-industry and industry-specific standards and codes in different industries; (2) select the most appropriate framework for assessing the degree of applicability of CSR in the selected management systems and develop a methodology for its assessment; (3) apply the proposed methodology (referred to as SRIMS) in the selected areas: automotive industry, research organization, and metallurgical industry; (4) through ANOVA, validate its use for assessing the overall level of CSR applicability in an organization's established management systems. The application of the Bonferroni method confirmed the hypotheses that the developed SRIMS model is a sufficiently appropriate tool for assessing the overall level of applicability of CSR requirements to established MSs.

Climbing plants require an external support to grow vertically and enhance light acquisition. Climbers that find a suitable support have greater performance and fitness than those that remain prostrate. Support search is characterized by oscillatory movements (i.e., circumnutation), in which plants rotate around a central axis during their growth. Numerous studies have elucidated the mechanistic details of circumnutation, but how this phenomenon is controlled remains unclear. Here, we use supervised machine learning algorithms to generate models that learn to discriminate between the presence/absence of a support in the environment. Results indicate that there is a difference in the pattern of circumnutation, depending on the presence of a support, that can be learned and classified rather accurately. We also identify distinctive kinematic features that contribute to the classification tasks. Overall, machine learning approaches appear to be powerful tools for understanding the movement of plants.

Acute vertigo and dizziness are frequent presenting symptoms in patients on the emergency department. With a broad differential diagnosis and symptoms/signs often subtle and transient, the diagnostic approach to the dizzy patient remains challenging. Previous work emphasized the value of combining structured history-taking and a targeted examination focusing on subtle oculomotor signs. Here I review different bedside algorithms proposed for the acutely dizzy patient. Comparing area-under-the-curve ROC-characteristics and sensitivity/specificity, highest diagnostic accuracy was observed for algorithms focusing on subtle oculomotor signs. Both the HINTS+ bedside-exam and the STANDING algorithm have demonstrated higher diagnostic accuracy for identifying strokes than early (<24-48h after symptom-onset) MRI-DWI. Importantly, HINTS and STANDING require moderate training to allow reliable application. Thus, for physicians lacking dedicated training, other approaches are needed. Various scores that rely on vascular risk-factors, clinical symptoms and focal neurologic findings have been proposed (e.g., ABCD2-score, PCI-score, TriAGe+-score). While these scores are more readily applicable for frontline providers, they provide intermediate diagnostic accuracy at best and often lack external validation, thus are an insufficient substitute for algorithms assessing subtle oculomotor findings. Providing dedicated training in HINTS+ or STANDING techniques will be key to improve the diagnostic accuracy and to avoid unnecessary brain imaging.

Hereditary cardiomyopathies (CMPs), including Arrhythmogenic Right Ventricular Cardiomyopathy (ARVC), Dilated Cardiomyopathy (DCM), and Hypertrophic Cardiomyopathy (HCM), represent a group of heart disorders that significantly contribute to cardiovascular morbidity and mortality and are often driven by genetic factors. Recent advances in Next-Generation Sequencing (NGS) technology have enabled the identification of rare variants in both well-established and minor genes associated to CMPs. Nowadays, a set of core genes is included in diagnostic panels for ARVC, DCM, HCM. On the other hand, despite their lesser-known status, variants in the minor genes may contribute to disease mechanisms and influence prognosis. This review evaluates the current evidence supporting the involvement of the minor genes in CMPs, considering their potential pathogenicity and clinical significance. A comprehensive analysis of databases such as ClinGen, ClinVar, and GeneReviews, along with recent literature and diagnostic guidelines, provides a thorough overview of the genetic landscape of minor genes in CMPs and offers insights for future research and translation to clinical practice. Given the increasing knowledge on these less-understood genetic factors, future studies are essential to clearly assess their roles, ultimately leading to improved diagnostic precision and therapeutic strategies in hereditary CMPs.

Costa Rica, renowned for its environmental sustainability, faces a pressing waste management crisis that endangers its ecological and public health achievements. This study provides a detailed analysis of Costa Rica's waste management challenges, particularly in urban areas like San José, where nearly half of the nation's waste is produced. Major issues include insufficient landfill capacity, a low recycling rate of 9.6%, and significant regional disparities in waste practices. Using a hybrid modeling approach with Linear Regression and ARIMA models, the study forecasts waste minimization trends from 2024 to 2050, emphasizing the critical role of public participation in recycling efforts.The findings reveal limited success in government initiatives like the Environmental Health Route and the National Circular Economy Strategy, especially in rural areas. The study underscores the need for improved infrastructure, targeted public education, and the adoption of innovative technologies like AI and blockchain to achieve sustainable waste management. Strategic recommendations are provided to help Costa Rica align its waste management practices with global standards, enhancing its environmental sustainability and addressing the ongoing crisis effectively.

The increasing emergence of multidrug resistant (MDR) pathogens causes difficult-to-treat infections, with long-term hospitalizations and high incidence of death, thus representing a global public health problem. To manage MDR bacteria bugs, new antimicrobial strategies are necessary, and their introduction in practice is a daily challenge for scientists in the field. An extensively studied approach to treat MDR infections consists in inducing high levels of reactive oxygen species (ROS) by several methods. Although further clinical investigations are mandatory on the possible toxic effects of ROS to mammalian cells, clinical evaluations are extremely promising, and their topical use to treat infected wounds and ulcers, also in presence of biofilm, is already clinically approved. Biochar (BC) is a carbonaceous material obtained by pyrolysis of different vegetable and animal biomass feedstocks, at 200−1000 °C in limited presence of O2. Recently, it has been demonstrated that BC capability of removing organic and inorganic xenobiotics is mainly due to the presence of persistent free radicals (PFRs), which can activate oxygen, H2O2 or persulfate in the presence or not of transition metals by electron transfer thus generating ROS, which in turn degrade pollutants by advanced oxidation processes (AOPs). In this context, the antibacterial effects of BC containing PFRs have been demonstrated by some authors against Escherichia coli and Staphylococcus aureus, thus giving birth to our idea of the possible use of BC-derived PFRs as a novel method capable of inducing ROS generation for antimicrobial oxidative therapy. Here, the general aspects concerning ROS physiological and pathological production and regulation, and the mechanism by which they could exert antimicrobial effects have been reviewed. The methods currently adopted to induce ROS production for antimicrobial oxidative therapy have been discussed. Finally, for the first time, BC-related PFRs have been proposed as a new source of ROS for antimicrobial therapy via AOPs.

Background/Aim: Performing emergency surgery for bowel obstruction continues to place a significant strain on the healthcare system. Conventional assessment methods for outcomes in bowel obstruction cases often concentrate on isolated factors, and the evaluation of results for individuals with bowel obstruction remains poorly studied. This study aimed to examine the risk factors associated with major postoperative complications. Methods: We retrospectively analyzed 99 patients undergoing surgery from 2015 to 2022. We divided the patients into two groups: 1) benign related obstruction (n=68), 2) cancer related obstruction (n=31). We used logistic regression, KNN and XGBOOST. We calculated the receiver operating characteristic curve, and accuracy of the model. Results: Colon obstructions were more frequent in the cancer group (p=0.005). Operative time, intestinal resection and stoma were significantly more frequent in the cancer group. Major complications were 41% for the cancer group vs. 20 in the benign group (p=0.03). Uni-and multivariate analysis shows that significant risk factors for major complication were cancer related obstruction and CRP. The best model was KNN with an accuracy of 0.82. Conclusion. Colonic obstruction is associated with a tumor-related blockage. Malignant cancer and an increase in C-reactive protein (CRP) are significant risk factors for patients who have undergone emergency surgery due to major complications. KNN could improve the process of counseling and the perioperative management of patients with intestinal obstruction in emergency settings.

Patients who survived critical COVID-19 frequently reported post-acute sequelae of COVID-19 (PASC) such as psychosomatic and neurocognitive health problems. The goal of this study was to identify clinical risk factors and other predictors for such long-term consequences in severely ill COVID-19 patients. Adult COVID-19 intensive care unit (ICU) survivors from August 2020 to May 2021 were enrolled. A broad range of clinical, laboratory and chest computed tomography (CT) data was collected during ICU stay. The association between ICU predictors and psychosomatic, respiratory and neurocognitive assessments 12 months after ICU discharge was analyzed using univariate regression analysis. In 17 patients (mean age 58.9 ± 11.4 years), laboratory markers (CRP, lymphocytes, hemoglobin), ICU severity (SOFA, SAPS II, need for mechanical ventilation), complications (ARDS), and lung CT data (ground-glass opacity) were promising predictors of depressive and anxiety symptoms, fatigue, and sleep problems. Recovery of psychosomatic health such as fatigue, depression and anxiety correlated with lower levels of inflammation and high hemoglobin levels. ARDS, mechanical ventilation and worse SOFA and SAPS II scores were further risk factors for depressive and anxiety symptoms. Our study identified novel associations such as pulmonary ground-glass opacity being positively associated with depression, anxiety, fatigue, and insomnia levels.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

Precipitation patterns are critical for understanding the hydrological and climatological dynamics of any region. Sicily, the largest island of the Mediterranean sea, with its diverse topography and climatic conditions, serves as an ideal case study for analyzing precipitation data to gain insights into regional water resources, agricultural productivity, and climate change impacts. This paper employs advanced statistical physics methods, particularly Tsallis q-statistics, to analyze sub-hourly precipitation data from 2002 to 2023, provided by the Sicilian Agrometeorological Informative System (SIAS). We investigate several critical variables related to rainfall events, including duration, depth, maximum record, and inter-event time. The study spans two decades (2002-2012 and 2013-2023), analyzing the distributions of relevant variables. Additionally, we examine the simple returns of these variables to identify significant temporal changes, fitting these returns with q-Gaussian distributions. Our findings reveal the scale-invariant nature of precipitation events, the presence of long-range interactions and memory effects, characteristic of complex environmental processes.

The rise of multi-sided digital platforms has transformed the global economy, enabling individuals and companies to create, deliver, and capture value through innovative connections and network effects. While scholars have studied the core strategy concepts and proposed platform architectures, less attention has been paid to the long-term sustainability of these platforms. This paper addresses this gap by examining the relationship between sustainability and platform architecture. Specifically, it asks what mechanisms characterize digital platforms for sustainability, and whether there are design choices that optimize the business model for sustainability. Using a mixed-methods approach that draws on platform literature, business models, and sustainable innovation, the paper develops an integrative framework to identify elements and design choices in platform businesses which support sustainability outcomes. The framework is then used to classify the business models of the identified platforms, revealing specific design choices for platform architecture that can optimize their business models for sustainability. This contribution to existing literature provides an artifact that allocates key decisions on value creation, delivery, and capture that are key to platforms and includes an additional layer to optimize them for long-term sustainability. As digital platforms continue to drive the economy, this research is relevant not only to platform practitioners, but also to policy makers and society at large.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature elevations in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear correlation of the data were estimated on 0.47oC for the 20 years between 1995 and 2015; the study showed that 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming. For the local influences some practical mitigation actions are proposed, related to improve the energy management and paying more attention to the temperature changes trough improvements in the number and capability of sampling stations in the urban air and in the river, which serve as clear indicators of the changes and the effect of any mitigation measures.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature raises in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear tendencies, were estimated on 0.47ºC for the 20 years between 1995 and 2015; 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.

Background: Arthroscopic revision rotator cuff repair (ARRCR) is challenging. Biologic strategies seem to be promising. The aim was to evaluate the effectiveness of combination of microfractures of the greater tuberosity, augmentation with collagen patch graft, and platelet concentrate injections in ARRCR. Methods: A retrospective comparative study was conducted on patients that underwent ARRCR with minimum two-years follow-up. Patients in the augmentation group underwent ARRCR combined with microfractures, collagen patch graft, and postoperative subacromial injections of platelet concentrate. A standard rotator cuff repair was performed in the control group. Primary outcome: Constant Murley score (CMS). Secondary outcomes: disease-specific health-related quality of life by using the Disabilities of the Arm, Shoulder and Hand (DASH) score; assessment of tendon integrity with magnetic resonance at least six months after surgery. Significance was set at p < 0.05. Results: Forty patients were included. Mean follow-up was 36.2 + 8.7 months. The mean CMS was greater in the augmentation group (p = 0.022). No differences could be found for DASH score. Healing failure rate was higher in the control group (p = 0.002). Conclusion: Biologic augmentation of ARRCR by combination of microfractures, collagen patch graft and subacromial injections of platelet concentrate is an effective strategy in improving tendon healing rate.

Keywords: chronic lymphocytic leukemia; older patient, Bruton tyrosine kinase, BCL2, cost-effectiveness Bruton tyrosine kinase inhibitors (BTKi) and the BCL2 inhibitor venetoclax, with or without the anti CD20 monoclonal antibody Obinutuzumab, represent the preferred options for the first-line therapy of CLL because they are more effective and may improve quality of life. However, pa-tient’s inclusion criteria were heterogeneous across trials designed for older patients and the identification of CLL-specific parameters identifying unfit patients at risk of developing drug-specific adverse events are required to guide treatment choice. Due to inclusion/exclusion criteria in trials, higher discontinuation rates with BTKi were reported in real-world studies and registry analyses provided useful information on factors predicting for earlier discontinuation in a real-world setting. Though targeted agents were shown to be cost-effective treatments in high-income countries, the out-of-pocket expenses may limit accessibility to these drugs and the overall expenditure for new drugs in CLL is projected to increase substantially posing an issue for sustainability. This being said, the choice of a finite duration treatment based on venetoclax containing regimens or treatment until progression with BTKi is today possible in high- income countries and the therapy choice drivers are represented by coexisting medical conditions rather than age, by patient expectations, logistics and sustainability.

This study presents the results of a research project financed by the Lazio Regional Government. The research focused on defining an integrated model of recent alluvial deposits in the Tiber River. To achieve this objective, geological boreholes were made to monitor the aquifer and in situ and laboratory tests carried out. The data obtained was used to detail stratigraphic aspects and improve the comprehension of water circulation beneath the recent alluvial deposits of the Tiber River in the urban area of Rome, between the Ponte Milvio bridge and the Tiber Island. The stratigraphic intervals recognised in the boreholes were parameterised based on their litho-technical characteristics. The new data acquired, and integrated with existing data in the CNR IGAG database, made it possible to produce a three-dimensional model of the lithologies in the study area.The model of the subsoil, simplified for applied reasons, was described in hy-drostratigraphic terms: three different lithotypes were subjected to piezometric levels monitor-ing. Finally, the research generated a numerical hydrological level in a stationary regime. In general, this study demonstrates how a numerical hydrogeological model calibrated by piezo-metric monitoring data can support the construction of a geological model, discarding or con-firming certain hypotheses and suggesting other means of reconstructing sedimentary bodies.

In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.

Climbing is an Olympic discipline in full development and multidisciplinary in nature, in which the influence of body composition and nutritional status on performance has not yet been clarified despite the quest for low weight in anti-gravity disciplines such as climbing. The present study aimed to do a nutritional (3-day dietary diaries) and body composition (ISAK profile) assessment of sport climbing athletes of different genders and sport levels. The mean age of the forty-six Spanish climbers (22 men and 24 women) was 30 years (SD: 9) with 7.66 years of experience (SD: 6.63). The mean somatotype of the athletes was classified as balanced mesomorph. Negative correlations were observed between fat mass variables and climbing level (p

The destruction of natural habitat for cropland and pastures represents a major threat to global biodiversity. Despite widespread societal concern about biodiversity loss associated with food production, consumers access to quantitative estimates of the impact of crop production on the world’s species has been very limited compared to assessments of other environmental variables such as greenhouse gas emissions or water use. Here, we present a consistent dataset of the biodiversity footprints of pastures and 175 individual crops at country level. The data were generated by combining maps of the global distribution of agricultural areas in the year 2000 with spatially explicit estimates of the biodiversity loss associated with the conversion of natural habitat to farmland. Estimates were derived for three common alternative measures of biodiversity – species richness, threatened species richness, and range rarity – of the world’s mammals, birds, and amphibians. Our dataset provides important quantitative information for food consumers and policy makers, allowing them to take evidence-based decisions to reduce the biodiversity footprint of global food production.

A Systemic Lupus Erythematosus (SLE) is a prototypical systemic autoimmune disease characterized by a complex interplay of genetic, molecular, and cellular factors. It is considered a multifactorial disorder influenced by genetic susceptibility, environmental triggers, and dysregulated immune responses. Understanding the molecular and cellular mechanisms driving SLE pathogenesis has been instrumental in developing targeted therapies to manage the disease and improve patient outcomes. In this essay, we will delve into the intricate molecular and cellular processes underlying SLE and examine the key lessons learned from human therapies.

The article presents an experience based on the design of DIY materials (Do-It-Yourself) as a phenomenon that contributes to the circular economy, making use of household waste and organic binders. The development context is the southernmost Industrial Design School in Latin America, where students are educated through the transfer of knowledge emphasized on the experimentation and territory assessment. Methodology corresponds to the traditional industrial design process, inserting DIY design of materials in the strategic stage. Objective and subjective variables are determined applied in the definition of new materials, being able to determine a range of proposals based on household waste. Citrus × Sinensis, Peperomia caperata (Piperaceae), Radiata pine veneers, among them, which are conceived by students to be self-produced at the user level. The results are materials elaborated based on household waste, exemplified with three types based on organic husks. Beyond findings associated to technique, compatibilities between residual materials and results expressed in materials and catalogs, it is possible to educate future designers on the innovative theme, with the potential to improve life quality of people and their environments.

This paper shows the results of applying high-resolution Unmanned Aircraft System (UAS) photogrammetric surveying on a large landslide. A real case study, where permanently installing GCPs could be complex, where natural shaped and formed land pose severe limitations in deploying ground targets with optimal geometric configuration. We analysed performances in terms of survey accuracy obtained by performing photogrammetric surveys through the Zenmuse P1 DJI optical camera and Phantom 4 Pro 2. In combination with DJI Matrice 300 UAS, the P1 camera allows direct georeferencing through GNSS observations in RTK mode. Photogrammetric surveys, performed through different georeferencing methods, have been compared. Several targets have been permanently installed on the ground over the maximum vegetation height to guarantee long-lasting reference over the years in the area, which is characterised by a diffuse short vegetation coverage. Multitemporal UAS surveys have been then compared using Digital Image Correlation (DIC) algorithms, and deformation maps have been produced. Afterwards, DIC results were compared with observations made by the GNSS ground-based permanent receivers resulting in a standard deviation of 0,077 m. Through results analysis, good accordance between ground-based GNSS observations and DIC analysis on the photogrammetric surveys have been identified for the same time span. To conclude, this type of landslide presents a moderate deformation speed; in such a case, effective deformations monitoring could be achieved using pseudo-direct georeferencing, which permitted a 0.24 m accuracy on the whole tested area.

Harmonic resonances are part of the Power Quality (PQ) problems of electrified railways and have serious consequences for the continuity of service and integrity of components in terms of overvoltage stress. The interaction between Traction Power Stations (TPSs) and trains that causes line resonances is briefly reviewed showing the dependence on infrastructure conditions. The objective is real-time monitoring of resonance conditions seen first of all from the onboard panto-graph interface, but it is equally applicable at TPS terminals. Voltage and current spectra, and de-rived impedance and power spectra, are analyzed proposing compact and efficient methods based on Short-Time Fourier Transform, suitable for real-time implementation with the hardware avail-able for energy metering and harmonic interference monitoring. The methods are tested by sweeping long recordings taken at some European railways, covering cases of longer and shorter supply sections, with a range of resonance frequencies of about one decade. They give insight into the spectral behavior of resonances, their dependency on position and change over time, and criteria to recognize genuine infrastructure resonances from rolling stock emissions.

This study examines the activities conducted at the archaeological site of Aptera in Crete, Greece. The research was part of the DIACHRONIC LANDSCAPES International Design Workshop, organized by the CAM (Center for Mediterranean Architecture), TUC (Technological University of Crete School of Architecture), and UNIFE (University of Ferrara Department of Architecture). This article outlines the methods used for data acquisition and processing on a territorial scale, which generated digital outputs necessary for the analysis and design phases of the workshop, as well as for further examination of the results. The collected data, obtained through low-cost aerial photogrammetric surveying and GNSS terrestrial coordinate detection, were integrated in a Structure from Motion workflow that led to the creation and exportation of various digital outputs, such as point clouds, DTM, DSM, orthophotos, and contour lines. An accuracy analysis was performed to evaluate the effectiveness and efficiency of the digital models compared to the implemented surveying strategies, including the Ground Control Point and Quality Check Point marker positioning strategy. The resulting digital models proved to be valuable assets for analysis and design within the workshop and provided insightful prospects for future research and territorial-scale projects.

The ongoing growth of international occurrence of depression and its ability to co-occur with other serious medical disorders such as heart disease, cancer, diabetes, and Parkinson’s disease is a current public health problem. Inhibitor of DNA-Binding/Differentiation (ID) proteins are part of a group of transcriptional factors that have been seen to be involved in neurocognitive disorders and therefore, may have influence on depressive disorders. Previously, it has been established that environmental estrogenic endocrine disruptors (EEDs) such as polychlorinated biphenyls (PCBs) & bisphenol A (BPA) have played an important role in the impact of depressive disorders. Hence, based on many studies, we consider the impact of these environmental pollutants on the group of ID proteins. Improved understanding of how the interaction of ID proteins by EED exposure can influence depressive disorders will contribute essential evidence that can further benefit our public health community with innovative knowledge to prevent these types of mental illnesses.

Gastric cancer is the fifth most common and fourth deadliest cancer worldwide, with a bleak 5-year survival rate of about 20%. Despite significant research into its pathobiology, prognostic predictability remains insufficient due to pathologists’ heavy workloads and the potential for diagnostic errors. Consequently, there is a pressing need for automated and precise histopathological diagnostic tools. This study leverages Machine Learning and Deep Learning techniques to classify histopathological images into healthy and cancerous categories. By utilizing both handcrafted and deep features and shallow learning classifiers on the GasHisSDB dataset, we conduct a comparative analysis to identify the most effective combinations of features and classifiers for differentiating normal from abnormal histopathological images without employing fine-tuning strategies. Our methodology achieves an accuracy of 95% with the SVM classifier, underscoring the effectiveness of feature fusion strategies. Additionally, cross-magnification experiments produced promising results with accuracies close to 80% and 90% when testing the models on unseen testing images with different resolutions.

Abstract The aim of our study is to analyse the perception of the families and concerned social workers. The research was conducted in an underprivileged and disadvantaged microregion in North Hungary. The main focus was the perception on the available health, educational, child welfare and social services and supports. The starting point was to enquire the target group’s knowledge of these services. The study examines the extent to which social work is able to provide support to disadvantaged, marginalized families with children, and the way how the dysfunctional operation of the system contributes to the perpetuation of the clients’ life conditions. Analysing the quality of these services and supports is crucial to understand the social mobility chance of the children living in this microregion. The results show that without capability and talent development for the children and given the lack of welfare services, the mobility chance and opportunities of these families are extremely low in Hungary.

The G protein-coupled receptor (GPCR) Smoothened (Smo) is a central signal transducer of the Hedgehog (Hh) pathway which has been linked to diverse forms of tumours. Stimulated by advancements in structural and functional characterisation, the Smo receptor has been recognised as an important therapeutic target in Hh-driven cancers, and several Smo inhibitors have now been approved for cancer therapy. This receptor is also known to be an oncoprotein itself and its gain-of-function variants have been associated with skin, brain, and liver cancers. According to the COSMIC database, oncogenic mutations of Smo have been identified in various other tumours, although their oncogenic effect remains unknown in these tissues. Drug resistance is a common challenge in cancer therapies targeting Smo, and data analysis shows that healthy individuals also harbour resistance mutations. Based on the importance of Smo in cancer progression and the high incidence of resistance towards Smo inhibitors, this review suggests that detection of Smo variants through tumour profiling could lead to increased precision and improved outcomes of anti-cancer treatments.

This research focuses on examining the responses of interest groups listed in the European Transparency Register to the ongoing Russia-Ukraine war. Its aim is to investigate the nuanced reactions of 2,579 commercial and business associations and 2,957 companies and groups to the conflict, as expressed through their X (Twitter) activities. Utilizing advanced text mining, NLP and LDA techniques, this study conducts a comprehensive analysis encompassing language dynamics, thematic shifts, sentiment variations, and activity levels exhibited by these entities both before and after the outbreak of the war. The results obtained reflect a progressive decreasing in negative emotions regarding the conflict over time. Likewise, multiple forms of outside lobbying are identified in the communication strategies of interest groups. All in all, this empirical inquiry into how interest groups adapt their messaging in response to complex geopolitical events holds the potential to provide invaluable insights into the multifaceted role of lobbying in shaping public policies.

This paper describes the first results of an Image Recognition Based Location (IRBL) for mobile application focusing on the procedure to generate a Database of range images (RGB-D). In an indoor environment, to estimate the camera position and orientation, a prior spatial knowledge of the surrounding is needed. In order to achieve this objective a complete 3D survey of two different environment (Bangbae metro station of Seoul and E.T.R.I. building in Daejeon – Republic of Korea) was performed using LiDAR (Light Detection And Ranging) instrument and the obtained scans were processed in order to obtain a spatial model of the environments. From this, two databases of reference images were generated using a specific software realized by the Geomatics group of Politecnico di Torino (ScanToRGBDImage). This tool allow to generate synthetically different RGB-D images) centered in the each scan position in the environment. Later, the external parameters (X, Y, Z, ω, φ, κ) and the range information extracted from the DB images retrieved, are used as reference information for pose estimation of a set of acquired mobile pictures in the IRBL procedure. In this paper the survey operations, the approach for generating the RGB-D images and the IRB strategy are reported. Finally the analysis of the results and the validation test are described.

E-commerce has gained increased popularity over the last decade. To date, there is an open debate as to whether e-commerce or brick-and-mortar shopping is environmentally less sustainable, especially due to the growing mobility resources needed for e-commerce distribution. The analysis at hand compares the CO2-equivalent emissions of e-commerce and brick-and-mortar shopping of pharmaceutical products considering spatial aspects and the typical transport modal mix of consumers when doing online and offline shopping. The object of analysis is a retailer of pharmaceutical products, more precisely medicines, which offers, both, brick-and-mortar shop and online shopping possibilities. The results show that spatial aspects concerning the residential location of consumers, the vehicles used for shopping trips, the shopping basked size, and trip-chaining effects have a crucial impact on the mobility demand and CO2-equivalent emissions of the two commerce forms. In general, for rural and sub-urban areas, e-commerce results in lower CO2-equivalent emissions, while in urban areas, brick-and-mortar shopping is the favourable solution, if the consumers walk or cycle to the next pharmacy.

Electric power systems are experiencing relevant changes involving the growing penetration of distributed generation and energy storage systems, the introduction of electric vehicles, the management of responsive loads, the proposals for new energy markets and so on. Such evolution is pushing for a paradigm shift: the management must move from traditional planning and manual intervention to full “smartization” of medium and low voltage networks. Peculiarities and criticalities of future power distribution networks originate from the complexity of the system that includes both the physical aspects of electric networks and the cyber aspects, like data elaboration, feature extraction, communication, supervision and control; only fully integrated advanced monitoring systems can foster this transition towards network automation. The design and development of such future networks require distinct kinds of expertise in the industrial and information engineering fields. In this context, this paper provides a comprehensive review of current challenges and multidisciplinary interactions in the development of smart distribution networks.

The Social-Ecological Systems (SES) framework serves as a valuable framework to explore and understand social and ecological interactions, and pathways in water governance. Yet, it lacks a robust understanding of change. We argue an analytical and methodological approach to engaging global changes in SES is critical to strengthening the scope and relevance of the SES framework. Relying on SES and resilience thinking, we propose an institutional and cognitive model of change that institutions and natural resources systems co-evolve to provide a dynamic understanding of SES that stands on three causal mechanisms: institutional complexity trap, rigidity trap, and learning processes. We illustrate how Data Cube technology could overcome current limitations and offer reliable avenues to test hypothesis about the dynamics of social-ecological systems and water security by offering to combine spatial and time data with no major technical requirements for users.

The European Space Agency (ESA) defines as Earth observation (EO) Level 2 information product a single-date multi-spectral (MS) image corrected for atmospheric, adjacency and topographic effects, stacked with its data-derived scene classification map (SCM), whose thematic map legend includes quality layers cloud and cloud-shadow. ESA EO Level 2 product generation is an inherently ill-posed computer vision (CV) problem never accomplished to date in operating mode by any EO data provider at the ground segment. Herein, it is considered: (I) necessary not sufficient pre-condition for the yet-unaccomplished dependent problems of semantic content-based image retrieval (SCBIR) and semantics-enabled information/knowledge discovery (SEIKD) in multi-source EO big data cubes. (II) Synonym of EO Analysis Ready Data (ARD) format. (III) Equivalent to a horizontal policy for background developments in Space Economy 4.0. In compliance with the GEO-CEOS Quality Assurance Framework for EO Calibration/Validation guidelines, to contribute toward filling an analytic and pragmatic information gap from multi-sensor EO big data to timely, comprehensive and operational EO value-adding information products and services, this work presents an innovative AutoCloud+ CV software toolbox for cloud and cloud-shadow quality layer detection in ESA EO Level 2 product. In vision, spatial information dominates color information. Inspired by this true-fact, the inherently ill-posed AutoCloud+ CV software was conditioned, designed and implemented to be “universal”, meaning fully automated (no human-machine interaction is required), near real-time, robust to changes in input data and scalable to changes in MS imaging sensor’s spatial and spectral resolution specifications.

A series of nanospherical shaped silicates containing heteroatoms (Al, Zr or Ti) were successfully synthesized using TEOS or silica colloids as silicon source. These metallosilicate nanospheres were used as silicon nutrients to obtain silicalite zeolites having micro-mesoporosity with improved textural properties. The results demonstrated that TEOS acted as a suitable silicon source to produce amorphous silicates and a spherical-type hierarchical zeolite architecture with Zr and Ti heteroatoms included in their framework, with preferable particle size and crystallinity. The surface functionality of the mesostructured nanospheres and zeolite silicates provide active centers for the esterification of glycerol with acetic acid (EG) reaction. Besides, the dispersion of Cu or Fe entities on the surface of the nanospherical silicates and zeolites provided good catalytic performances in the esterification of glycerol to valuable acetins.

The contemporary discourse focuses on the fourth industrial revolution and its impact on compa-nies. An explicative, quantitative, questionnaire survey was conducted with managers of 101 companies in Hungary and 54 in Austria. Our study focused on assessing their preparedness for Industry 4.0 and the key factors they take into account when implementing Industry 4.0 initiatives. We also examined whether there is a correlation between the areas in which companies have made improvements to support Industry 4.0. To complement our quantitative analysis, we conducted a series of four semi-structured interviews with two Hungarian and two Austrian companies. The aim of the interviews was to further investigate the digital readiness of companies and to formulate recommendations for companies venturing into the field of digitalisation. A particular focus was put on comparing the digital maturity of these two neighbouring Central European countries, given the significant differences in their digital maturity as shown by the macro indicators of the Digital Economy and Society Index (DESI). Therefore, we conducted a micro-level analysis to investigate the extent to which DESI scores correspond to the digital performance of companies at the orga-nisational level.

Background: Dietary supplements (DS) represent a possible approach to improve sperm parameters and male fertility. A wide range of DS containing different nutrients is now available. Although many authors demonstrated benefits from some nutrients in male infertility, their real effectiveness is still under debate. The aim of this study was to critically review the composition of DS using the Italian market as sample. Materials & Methods: Active ingredients and their minimal effective daily dose (mFED) were identified through literature search. Thereafter, we created a formula to classify the expected efficacy of each DS. Considering active ingredients, their concentration and the recommended daily dose, DS were scored into three classes of expected efficacy: higher, lower and none. Results: Twenty-one DS were identified. Most of them had a large number of ingredients, frequently at doses below mFED or with unproven efficacy. Zinc was the most common ingredient of DS (70% of products), followed by selenium, arginine, coenzyme Q and folic acid. By applying our scoring system, 9.5% of DS fell in higher class, 71.4% in lower class and 19.1% in the class with no expected efficacy. Conclusions: DS marketed in Italy for male infertility frequently include effective ingredients but also a large number of substances at insufficient dose or with no proven efficacy. Manufacturers and physicians should better consider the scientific evidence on effective ingredients and their doses before formulating and prescribing these products.

Thermal plasma is a versatile technology that can be used to treat various types of wastes, including vegetal and mineral oils, solvents, plastics, papers and cardboard, glasses, bricks and rocks, metals, clothes, and mixtures of these materials. In this study, we utilized a commercial plasma cutter as a thermal plasma source to decrease the volume of a simulated low-level radioactive mixed solid waste. The simulated waste included papers, plastics, clothes, gloves, metals and stable Co, Cs, Sr, and Ce additives as surrogates of 60Co, 137Cs, 90Sr, and 144Ce, the latter typical contaminants in nuclear LLW. As a result of the process two products were obtained, a solid phase in which we focused this work and a gaseous phase. To retain as much as possible surrogates in the solid final phase, crushed glass from broken bottles was included as a vitrification additive to the original waste. After undergoing heat treatment, a dense vitreous slag was produced and ashes. The process resulted in a volume reduction of 70%, indicating the successful gasification of organic excess materials. The surrogate elements were retained in the process and were found in the ashes composition: Co (3.4% w/w), Cs (37.7% w/w), Ce (0.6% w/w) and in the glass matrix composition of Co, Cs, Sr and Ce: 72.4 ± 14.7, 32 ± 18.2, 125.3 ± 31.6, 80 ± 13.1 % w/w respectively. For the actual experimental conditions, retention efficiencies were estimated for Cobalt (Co) at 72.4 ± 14.7%, Cerium (Ce) at 80 ± 13.1%, Strontium (Sr) at 125.3 ± 31.6%, and notably Cesium (Cs) at 32 ± 18.2%.

Latin binomials, popularised in the eighteenth century by the Swedish naturalist Linnaeus, have stood the test of time in providing a stable, clear and memorable system of nomenclature across biology. However, relentless and ever-deeper exploration and analysis of the microbial world has created an urgent unmet need for huge numbers of new names for Archaea and Bacteria. Manual creation of such names remains difficult and slow and typically relies on expert-driven nomenclatural quality control. Keen to ensure the legacy of Linnaeus lives on in the age of microbial genomics and metagenomics, we propose an automated approach, employing combinatorial concatenation of roots from Latin and Greek to create linguistically correct names for genera and species that can be used off the shelf as needed. As proof of principle, we document over a million new names for Bacteria and Archaea. We are confident that our approach provides a road map for how to create new names for decades to come.

As the emission regulations get more and more stringent in the different fields of energy and environmental systems, the electric and fuel cell vehicles (FCV) have attracted growing attention by automakers, governments, and customers. Research and development efforts have been focused on devising novel concepts, low-cost systems, and reliable electric/fuel cell powertrain. In fact, electric and fuel cell vehicles coupled with low-carbon electricity sources offer the potential for reducing greenhouse gas emissions and exposure to tailpipe emissions from personal transportation. In particular, Pedal Assisted Bicycles (PAB) popularity is rising in urban areas due to their low energy consumption and environmental impact. In fact, when electrically moved, they are zero emission vehicles with very low noise emissions, as well. These positive characteristics could be even improved by coupling a PAB with a fuel cell based power generation system, thus increasing the vehicle autonomy without influencing their emissions and consumption performances. In this paper, four types of vehicles are compared from an environmental and accessibility point of view: conventional car, bus, electric PAB and hydrogen fuel cell PAB; for such vehicles, the respective utilization stages are accounted for, i.e. without considering the manufacturing process. The analysis has been carried out comparing different vehicles performance along different routes of an Italian middle-size city, Viterbo, which represents a very good pilot case as its Municipality is adopting many solutions suggested by European Union (EU) through the planning tool called Sustainable Energy Action Plan (SEAP). The comparison is based on an ad-hoc developed mathematical procedure, which includes environmental (greenhouse gas and air pollution emissions), health (pollutants toxicity levels) and accessibility time (waiting times) indicators. According to this analysis, electric and fuel cell PAB exhibit interesting advantages over the other vehicles. However, the global economic efficiency of electric or fuel cell apparatus depends substantially on the exploited source of electrical energy.

Despite laws and directives for the regulation and restriction of pesticide in farming, the large use of Plant Protection Products (PPPs) in paddy fields is a relevant worldwide cause of contamination of the environment. The aim of this work is to evaluate the environmental impact due to the use of PPPs by using an integrated approach based on chemical analyses and ecotoxicological hazard assessment, supported by statistical tools, in order to overcome the issues related to the traditional tabular evaluation. Samples of soil and water of seven conventional and organic paddies located in Northern Italy have been examined for two years by extensive chemical and ecotoxicological analyses. The results evidenced a direct relationship between the presence of Oxadiazon in water and bioassays responses as the main cause of the toxicity measured. This phenomenon affected both biological and conventional rice fields, due to the free circulation of water through irrigation canals. Therefore, the implementation of organic districts with a water circulation isolated from conventional fields represents a simple and effective countermeasure to safeguard the agricultural practices of organic crops.

Mediterranean Diet (MD), rich in minimally processed plant foods and in monounsaturated fats, but low in saturated fats, meat and dairy products, represents one of the most studied diets for cardiovascular health. It has been shown, from both observational and randomized controlled trials, that MD reduces body weight, improves cardiovascular disease surrogates such as waist-to-hip ratio, lipids, and inflammation markers, and even prevents the development of fatal and non-fatal cardiovascular disease, diabetes, obesity, and other diseases. However, it is unclear whether it offers cardiovascular benefits from its individual components or as a whole. Furthermore, limitations in the methodology of studies and meta-analyses have raised some concerns on its potential cardiovascular benefits. MD is also associated with characteristic changes in the intestinal microbiota, mediated through its constituents. These include increased growth of species producing short-chain fatty acids, such as Clostridium leptum and Eubacterium rectale, increased growth of Bifidobacteria, Bacteroides and Faecalibacterium prausnitzii species, and reduced growth of Firmicutes and Blautia species. Such changes are known to be favorably associated with inflammation, oxidative status, and overall metabolic health. This review will focus on the effects of MD on cardiovascular health through its action on gut microbioma.

This narrative review delves into the evolving landscape of fertility preservation techniques with a particular focus on their use in patients undergoing oncology treatment that carries a risk of ovarian insufficiency. Advances in established methods such as cryopreservation of oocytes and embryos are highlighted and the increasing use of gonadotropin-releasing hormone (GnRH) agonists is discussed. The review also addresses the complexities and controversies associated with these approaches, such as the 'flare-up' effect associated with GnRH agonists and the potential of GnRH antagonists to reduce the risk of ovarian hyperstimulation syndrome. Despite advances in fertility preservation, the report highlights the challenges we face, including the need for personalized treatment protocols and management of associated risks. It calls for continued research and collaboration between healthcare professionals to refine these techniques and ultimately improve reproductive outcomes for patients facing the prospect of fertility-impairing treatment.

New hybrid composites based on the inclusion of a vegetal extract, i.e., Boswellia Serrata extract (BSE), rich in boswellic acids, well known as a potent anti-inflammatory natural drug, in a lamellar solid layered double hydroxide (LDH), i.e. a Magnesium Aluminum Carbonate, were developed and characterized in the present work. The adopted LDH exhibits a layered crystal structure, comprised of positively charged hydroxide layers and interlayers composed of carbonate anions and water molecules, thus it was expected to embed negatively charged boswellic acids. In the present case, a calcination process was also adopted on LDH to increase organic acids loading, based on the replacement of original inorganic anions. An accurate investigation was carried out by TGA, PXRD, FT-IR/ATR, XPS and LC-MS to ascertain the nature, interaction, and quantifica-tion of the active molecules of the vegetal extract loaded in the developed hybrid materials. As a result, a significant disruption of the original layered structure was observed in LDH subjected to calcination (LDHc), and this material was able to include a higher amount of organic acids when its composite with BSE was prepared. However, in vitro tests on composites bioactivity, expressed in terms of antimicrobial and anti-inflammatory activity, evidenced LDH-BSE as a better material compared to BSE and to LDHc-BSE, thus suggesting that, though the embedded organic acids amount was lower, they could be more available since not firmly bound to the clay. The composite was able to significantly decrease the number of viable pathogens such as Escherichia Coli and Staphylococcus aureus, as well as the internalization of toxic active species into human cells imposed to oxidative stress in comparison to the BSE.

Heterojunctions based on metal halide perovskites (MHPs) are promising systems for photocatalytic hydrogen evolution reaction (HER). In this work, we coupled Cs3Bi2Br9 nanocrystals (NCs), obtained by wet ball milling synthesis, with g-C3N4 nanosheets (NSs) produced by thermal oxidation of bulk g-C3N4 in air. These methods are reproducible, inexpensive, and easy to scale up. Heterojunctions with different loadings of Cs3Bi2Br9 NCs were fully characterized and tested for HER. A relevant improvement of H2 production with respect to pristine carbon nitride was achieved at low NCs levels reaching values up to about 4600 µmol g-1 h-1. This work aims to provide insights on the synthesis of inexpensive and high performing heterojunctions using MHP for photocatalytic applications.

Background: The proven efficacy of mTOR inhibitors (mTORI), tyrosine kinase inhibitors (TKI) or immune checkpoint inhibitors (ICI) therapies in metastatic renal cell carcinoma (RCC), suggested that these agents should be investigated as adjuvant therapy with the aim of eliminating any residual undetectable microscopic disease after curative resection. Our study aimed to compare the efficacy of these treatments through the application of an innovative method that reconstructs individual patient data. Methods: Nine phase III studies describing different treatment options for adjuvant RCC were selected. Individual patient data were reconstructed from Kaplan–Meier (KM) curves through the “IPDfromKM method”. Disease-free survival (DFS) were compared among combination treatments and control arm (placebo). Results were summarized as multi-treatment KM curves. Standard statistical testing was used, including hazard ratio and likelihood ratio tests for heterogeneity. Results: In the overall population, this study showed that two ICIs (pembrolizumab and nivolumab plus ipilimumab) and one TKI (sunitinib) showed superiority over placebo, whereas both TKI and mTORI did not. As we assessed DFS as the primary endpoint for the adjuvant comparison, the overall survival benefit remains unknown.. Conclusion: This novel approach to investigating survival has allowed us to conduct all of the indirect head-to-head comparisons between these agents in a context where no "real" comparative trials have been conducted.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

The company strategic procurement function makes a significant contribution to overall corporate success, and yet remains under-researched in terms of digitalisation and digital maturity. This research adopts an inductive case study approach, using qualitative data from in-depth inter-views with industry practitioners, to develop and apply a digital maturity model for the deployment of strategic procurement analytics. The research presents a snapshot of the digital maturity of the strategic procurement function of a global aircraft manufacturer, and finds that current exploitation of analytics remains constrained by a range of factors, including the need for close compliance with regulatory norms. Thematic analysis of the interview material provides the basis for the development of the maturity model, which - although geared to a specific industry context - is nevertheless of relevance in other business environments. The research thus con-tributes to the existing literature in this field, and will also be of interest to procurement professionals. However, the research clearly has its limitations, not least in that it is based on just one industry case, and cross-industry generalisations from the findings must therefore be treated with caution.

Solid state sensors having timing capabilities are becoming an absolute need in particle tracking techniques of future experiments at colliders. In this sense, silicon sensors having 3D structure are becoming an interesting solution, due to their intrinsic speed and radiation resistance. A characteristics of such devices is the strict dependence of their performance on their geometric structure, which can be widely optimised by design, thus requiring suitable tools for an accurate modeling of their behaviour. This paper illustrates the development, performance and use of the TCoDe simulator, specifically dedicated to the fast simulation of carrier transportation phenomena in solid state sensors. Some examples of its effectiveness in the design and analysis of 3D sensors is also given.

Motivated by the importance of entanglement and correlation indicators in the analysis of quantum systems, we study the equilibrium and the residual entropy in a two-species Bose Hubbard dimer when the spatial phase separation of the two species takes place. We consider both the zero and non-zero-temperature regime. We present different kinds of residual entropies (each one associated to a different way of partitioning the system), and we show that they strictly depend on the specific quantum phase characterizing the two species (supermixed, mixed or demixed) even at finite temperature. To provide a deeper physical insight into the zero-temperature scenario, we apply the fully-analytical variational approach based on su(2) coherent states and provide a considerbly good approximation of the entanglement entropy. Finally, we show that the effectiveness of residual entropy as a critical indicator at non-zero temperature is unchanged when considering a restricted combination of energy eigenstates.

CAMx-LPiG (Comprehensive Air Quality Model with Extensions – Linear Plume in Grid) is an online hybrid model, based on the Chemistry and Transport Model (CTM) CAMx, that includes a sub-grid scale module to simulate the dispersion of linear road traffic emissions, called LPiG. LPiG is a plume in grid module specifically developed by extending the capabilities of the Lagrangian puff sub-grid model available in CAMx. The online integration of the local scale model within the Eulerian CTM allows for a multiscale simulation of air quality from the regional scale to the urban scale, preserving a coherent description of the chemical state of the atmosphere at all spatial scales and avoiding any double counting of the emissions simulated by the sub-grid module. In this work the model is presented and evaluated against measured NO2 concentrations for the city of Milan for the month of January 2017. The model is able to introduce road traffic induced gradient in NO2 concentration at sub-grid resolution. Moreover, CAMx-LPiG is shown to reduce the bias compared to CAMx stand-alone simulations.

The ATP synthase is a mitochondrial complex embedded in the inner mitochondrial membrane. The enzyme is under the double genetic control of the mitochondrial DNA (mtDNA) and nuclear DNA (nDNA). Fatal human diseases have been associated with defects in ATP synthase (Complex V) activity linked to mtDNA or nDNA pathogenetic variants in genes encoding structural subunits or assembly factors. Mitochondrial post-translational modifications of key amino acids, reduced/increased subunit expression, or protein to protein ATP synthase interaction, are also some of the mechanisms involved in the age-related disease pathway. All the major neurodegenerative diseases: Parkinson’s, Alzheimer’s and motor neuron diseases such as Amyotrophic Lateral Sclerosis highlight an impaired ATP generation in a mechanism involving the permeability transition pore that triggers a cellular homeostasis failure responsible for different forms of regulated cell death. In this review, we will explore ATP synthase assembly and function in physiological and pathological conditions by referring to the recent cryo-EM studies and by exploring human diseases models.

Asthma is a significant public health concern. This study identified the provinces with the highest morbidity and mortality rates due to asthma among the working-age population (15-69 years) in the Republic of Ecuador. The secondary objective was to explain the possible differences attribut-able to occupational exposure. This nationwide ecological and exploratory study was conducted in 24 provinces between 2016 and 2019. Government databases were used as sources of infor-mation. Standardized rates were calculated for codes the J45 and J46. The hospitalization mor-bidity rate for asthma decreased from 6.51 to 5.76 cases per 100,000 working-age population, and the mortality rate has consistently been low and stable from 0.14 to 0.15 deaths per 100,000 working-age population. Geographic differences between the provinces were evident. The risk of hospitalization and death due to asthma was higher in the Pacific coast (five provinces) and the Andean region (two provinces). The high rates observed in provinces with greater agricultural and industrial development could be the main determinants of national heterogeneity and could act as occupational risk factors. The contribution of occupational hazards in each province should be examined in depth through ad hoc studies. These findings provide valuable information for creating public policies aimed at promoting and safeguarding the respiratory health of the popu-lation, particularly that of workers.

We investigated the role of the human medio-temporal complex (hMT+) in the memory encoding and storage of a sequence of four coherently moving RDKs by applying repetitive transcranial magnetic stimulation (rTMS) during an early or late phase of the retention interval. Moreover, in a second experiment we also tested whether disrupting the functional integrity of hMT+ during the early phase impaired the precision of the encoded motion directions. Overall, results showed that both recognition accuracy and precision were worse in middle serial positions, suggesting the occurrence of primacy and recency effects. We found that rTMS delivered during the early (but not the late) phase of the retention interval was able to impair not only recognition of RDKs, but also the precision of the retained motion direction. However, such impairment occurred only for RDKs presented in middle positions along the presented sequence, where performance was already closer to chance level. Altogether these findings suggest an involvement of hMT+ in the memory encoding of visual motion direction. Given that both position sequence and rTMS modulated not only recognition but also precision of the stored information, these findings are in support of a model of visual short-term memory with a variable resolution of each stored item, consistent with the assigned amount of memory resources, and that such item-specific memory resolution is supported by the functional integrity of area hMT+.

Abstract: Urban population growth and the expansion of the built environment, pollution, overexploitation of water, inequality in water distribution, and the impacts of climate change in future availability of water, are all elements that jeopardize urban water security. Due to the complexity of urban water systems and their relevance for urban life, a holistic and integrative perspective is therefore needed to address such challenges. In this paper, Urban Water Metabolism (UWM) has been used for comprehensively understanding water (in)security in the City of Puebla (Mexico) and its metropolitan area. Water inflows and outflows have been estimated using a Material Flow Analysis (MFA) method with data either obtained from official sources or simulated with the Monte Carlo method. Our findings show that the UWM configuration in the City of Puebla and its metropolitan area is effective for generating profits to service providers and water related business, yet ineffective to guarantee citizens’ Human Right to Water and Sanitation (HRWS), a right recognized in the Constitution of Mexico. We conclude that to advance towards an inclusive and sustainable provision of water, economic interests must be reconsidered and therefore adjusted so they can be in line with such aspirational socioecological goals. UWM accounting can therefore inform new water governance arrangements, those based on both the best available knowledge and a vibrant participation of all relevant stakeholders.

This review explores the combination of renewable energy production and agriculture through agrivoltaic, with a focus on its impact on fruit crops. As the world seeks alternatives to fossil fuels, agrivoltaics offers a promising solution by integrating solar panels with farming practices. The study examines various agrivoltaic configurations with different fruit crops, emphasizing their influence on microclimatic conditions beneath the panels and the effects on crop produc-tion. In particular, it underscores the need for tailored solutions to balance energy yield and crop productivity and quality, with different shading levels affecting fruit quality/production. De-spite ongoing research, a comprehensive understanding of agrivoltaics' potential benefits and challenges remains crucial for its successful application and implementation in sustainable ag-riculture.

Cities have witnessed a booming interest in cycling in recent years. However, the implementation of cycling networks rarely followed a strategy to make them more accessible to specific social groups, such as women. To address this gap in knowledge, this paper provides a holistic perspective of women’s cycling mobility. Specifically, the study’s goal is to look into the social and environmental implications of cycling for women in Turin, Italy. Hence, this paper provides insights for ensuring a woman-friendly cycling system in a city and ensuring women’s participation as vital stakeholders in promoting a bike-friendly identity. We clarify women’s perceptions of cycling and outline the requirements for more inclusive bike infrastructures. Thus, we identify strategies to improve women’s access to bike lanes and investigate the environmental benefits of reduced air pollution by such a bike system. All this information is intended to define a more socially inclusive and environmental-friendly transport system in Turin for everyone, as depicted in Goal 11 of Sustainable Development Goals (SDGs).

Radon (²²²Rn) is the second most common type of lung cancer after smoking. As radon poses a significant risk to human health, radon-affected areas should be to ensure people’s awareness of risk and remediation. The primary goal of this research was to investigate the local natural radioactivity (in soils, water and indoors) because of the presence of tuff outcrops (from middle lower Pleistocene volcanic activity) that naturally produce radioactive gas radon at Cerveteri (Rome, Central Italy). The study area is characterized by the presence of several funerary sites pertaining to the Etruscan Necropolis of Cerveteri, which extends over a volcanic rock plateau. The results of the radon survey highlighted moderate (>16000 Bq/m³) but localized anomalies in soils and medium low (< 200 Bq/m³) values of indoor radon excepting some cases exceeding the threshold (> 300 Bq/m³) recommended by 2013/59 Euratom Directive. Although for thoron (²²⁰Rn) effects on human health, there exist no clinical data, the study of ²²⁰Rn average activity concentration in the soil gas survey has revealed new insights for the interpretation of radon sources that can affect dwellings, even taking into account the considerable difference in the half-lives of the ²²²Rn and ²²⁰Rn.

There is a major problem with the rising occurrence of highly virulent and multiply-resistant strains, including methicillin-resistant Staphylococcus aureus (MRSA), because of their difficult treatment. This study aimed to evaluate the antibacterial and antibiofilm effect of new enterocins (Ent) against potential pathogenic MRSA strains isolated from rabbits. Staphylococci (n =110) were identified with PCR and screened for methicillin/oxacillin/cefoxitin resistance (MR) using the disk diffusion method and the PBP2' Latex Agglutination Test Kit. Enzyme production, hemolysis, DNase activity, slime production, and biofilm formation were tested in MRSA strains. The susceptibility of MRSA to eight partially-purified enterocins (Ent) produced by E. faecium and E. durans strains was checked using agar spot tests. The antibiofilm activity of Ents was tested using a quantitative plate assay. Out of 14 MRSA, PBP testing confirmed MR in 8 strains. The majority of MRSA showed DNase activity and β-hemolysis. Slime production and moderate biofilm formation were observed in all strains. MRSA were susceptible to tested Ents (100–12800 AU/mL; except Ent4231). The antibiofilm effect of Ents (except Ent4231) was noted in the high range (64.9-97.0%). These results indicate that enterocins offer a promising option for the prevention and treatment of bacterial infections caused by biofilm-forming MRSA.

Beaches are among the habitats most frequented by migratory birds for breeding and/or wintering. However, threats such as human pressure and sea level rise can reduce the availability of these habitats for different species. The presence of alternative areas, such as salt pans and brackish habitats, is essential for many migratory shorebird populations. This study addresses the post-breeding dispersal of the Kentish plover (Charadrius alexandrinus) in the Iberian Peninsula by analysing C and N isotopes in feathers. The study was conducted at six locations along the Iberian coast, which were categorized in three areas: NW Atlantic coast, the Atlantic coast of Andalusia and the Mediterranean coast. Although linear mixed models did not reveal any significant effects of sex or coastal area on isotopic levels, the variability in the data suggests different habitat-use strategies in the post-reproductive period. Birds from the northwest of the Iberian Peninsula exhibit greater fidelity to a single habitat type, i.e. coastal beaches, while populations from the Mediterranean coast and the Atlantic coast of Andalusia show different individual dispersal strategies, occupying coastal habitats and freshwater wetlands. The lack of alternative habitats for the northwest Iberian population, the reduction in available habitat due to rising sea levels and human pressure together pose a serious threat to the survival of this species, already with an unfavourable conservation status.

This paper deals with the analysis of the cognitive functions of the cerebral cortex or cortex in the evolutionary context. The triune brain model is presented given its notorious popularity in fields that are not strictly neuroscientific, and its limitations and inaccuracies are also shown. Although it is an outdated theory, this one represented the passage to a new era, because it really was the model of the movement towards understanding the brain in evolutionary terms. Next, the paper illustrates the different areas of the cortex and their functions, as well as the evolution of the brain and the cortex in vertebrates. To date, the expansion of the cortex with the amniotes was placed 300 million years ago, although recent studies place it in the lampreys more than 500 million years ago. Evolutionary changes in mammalian brain and cortex size are discussed, showing the evolution from three to six cell layers and trends in different groups of mammals. Finally, the most recent contributions in the field of research are illustrated, such as the role of neurogenesis and the evolution of the connectivity of the cortex.

This paper aims to present the method of producing visual media for communicating the Asinara Island National Park plan. These products are landscape visualizations able to foster landscape preservation both from the point of view of the management of the landscape and of the citizen's involvement in the communication of the historical and environmental values of the landscape. Starting from landscape information gathering, the research has experimented with an operative method for processing different graphic representations from the same geographic database, calibrating the outputs to different audiences, their needs, objectives, and literacy skills. Three different types of products are presented: the first is a digital, dynamic and multisectoral decision-making GIS tool for park management. The second is a 3D model, aimed to the virtual fruition. The third is a map of the zoning park plan drawn to be easily readable to the non-expert public. This case study emerges as a replicable method to process the landscape information to make different visualization tools from a single geographic model, to meet the different requirements that arise from a complex landscape planning process.

The energy efficiency of ice hockey arenas is a central concern for the administrations, as these buildings are well known to consume a large amount of energy. Since they are composite, complex systems, solutions to such a problem can be approached from many different areas, from managerial to technological to more strictly physical. In this paper we consider heat transfer processes in an ice hockey hall, during operating conditions, with a bottom-up approach based upon on-site measurements. Detailed heat flux, relative humidity and temperature data for the ice pad and the indoor air are used for a heat balance calculation in the steady-state regime, which quantifies the impact of each single heat source. We then solve the heat conduction equation for the ice pad in transient regime, and obtain a generic analytical formula for the temperature profile that can be used in practical applications. We then apply this formula to the resurfacing process for validation, and find good agreement with an analogous numerical solution. Since it is given with implicit initial condition and boundary conditions, it can be used not only in ice hockey halls, but in a large variety of engineering applications.

Oxidative stress plays an essential role in the pathological processes that trigger various chronic liver diseases and contributes to the development of hepatocarcinogenesis. Antioxidants from natural sources trap free radicals by converting them into non-harmful products and minimize oxidative stress, playing a crucial function in the treatment of free radical-induced diseases. However, the activity of these antioxidants is limited due their poor bioavailability, which is why various nano-drug delivery systems have been developed to improve their stability, promote smooth release, and targeted delivery for liver cancer treatment. Specifically, this review aims to report recent scientific findings of novel nano-formulations containing natural antioxidant molecules targeted for the treatment of liver cancer.