The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

It is well known that human activities and climate change have increased steppe habitat loss and fragmentation in Northwest China. Carabid beetles are often used as bioindicators of environmental change because they are extremely sensitive to disturbance. We chose 42 landscapes (18 fragmented and 24 continuous) in both desert and typical steppes of Northwest China to examine the influence of habitat loss and fragmentation on carabid beetle communities. The results showed the largest correlation coefficient between carabid communities and landscape compositions within a 7-km spatial scale in both desert and typical steppes. Further, the response of carabid communities to habitat fragmentation was species-specific in both desert and typical steppes. Habitat fragmentation in the desert steppe had positive effects on the richness and abundance of carabid communities, while in the typical steppe, the effects were negative. Additionally, habitat fragmentation significantly decreased the abundance of two common carabid species in the desert steppe. Therefore, the effects of habitat fragmentation on carabid biodiversity differ with species characteristics and habitat traits, where plant communities, soil structure, and microclimate vary in the different steppe types. The results of this study provide experimental evidence and technical support for biodiversity conservation management in the steppes of Northwest China.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

(1) Background: The rapid development of information technology has changed the traditional concept of space, gradually shifting the "container space" to the "relational space" . The constraints of geographical spatial elements are diminishing, and the theory of virtual agglomeration is gaining attention. (2) Methods: In this study, we constructed an evaluation system for virtual agglomeration, comprising four primary indicators: virtual infrastructure level, virtual output level, virtual input level, and virtual service level. The TOPSIS method was used to calculate the virtual agglomeration level for each province, and the DEA-Malmquist method was employed to measure provincial total factor productivity (TFP) in China. Using panel data from 30 provincial regions in China from 2013 to 2021, we examined the mechanism and impact path of virtual agglomeration on TFP. (3) Result: There is an inverted U-shaped relationship between virtual agglomeration and TFP in China. The overall development level of virtual agglomeration is relatively low, within the range where the marginal effect of virtual agglomeration on TFP is positive but diminishing, indicating significant potential for further development. The impact of virtual agglomeration on TFP is stronger in the Yangtze River Economic Belt compared to non-Yangtze River areas, and the highest stable point of TFP is higher in central provinces than in eastern and western provinces. (4) Conclusions: This study provides a theoretical basis and practical reference for improving the level of virtual agglomeration.

Abstract: Microstructural and mechanical properties of the eutectic Sn58Bi and micro-alloyed Sn57.6Bi0.4Ag solder alloys were compared. With the addition of Ag micro-alloy, the tensile strength was improved and this is attributed to a combination of microstructure refinement and an Ag3Sn precipitation hardening mechanism. However, ductility is slightly deteriorated due to the brittle nature of the Ag3Sn intermetallic compounds (IMCs). Additionally, a board level reliability study of Ag micro-alloyed Sn58Bi solder joints produced utilising a surface-mount technology (SMT) process, were assessed under accelerated temperature cycling (ATC) conditions. Results reveal that micro-alloyed Sn57.6Bi0.4Ag has a higher characteristic lifetime with a narrower failure distribution. This enhanced reliability corresponds with improved bulk mechanical properties. It is postulated that Ag3Sn IMCs are located at the Sn-Bi phase boundaries and suppress the solder microstructure from coarsening during the temperature cycling, hereby extending the time to failure.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

Transverse momentum spectra of +, p, Λ, Ξ or ¯Ξ+, Ω or ¯Ω+ and deuteron (d) in different centrality intervals in Gold-Gold (Au-Au) and Lead-Lead (Pb-Pb) collisions at 62.4 GeV and 2.76 TeV respectively, are analyzed by the blast wave model with Boltzmann Gibbs statistics. We extracted Kinetic freeze out temperature,transverse flow velocity and kinetic freezeout volume from the transverse momentum spectra of the particles. It is observed that the non-strange and strange (multi-strange) particles freezeout separately due to different reaction cross-sections. While the freezeout volume and transverse flow velocity are mass dependent which decrease with the rest mass of the particles. The present work reveals the scenario of double kinetic freezeout in collisions at STAR and ALICE Collaborations. Furthermore, the kinetic freezeout temperature and freezeout volume are larger in central collisions than the peripheral collisions and they decrease from central to periphery. However the transverse flow velocity remains almost unchanged from central to peripheral collisions.

The main purpose of study is to identify the impact of COVID-19 pandemic on the green financing of banks and non-bank financial institutions (NBFIs) in an emerging economy such as Bangladesh. Also, this study shows the green banking activities of the banks and NBFIs during the pandemic. To analyze the impact of the pandemic on green financing, secondary data were obtained from the quarterly and annual reports of Bangladesh Bank (BB) on green financing as well as the annual reports and websites of 61 banks and 34 NBFIs in Bangladesh for the period 2021–2019. Subsequently, the study deployed dependent t-test statistics, growth rate (year-on-year), descriptive statistics, relative percentage changes, and varying tables and graphs to analyze the obtained secondary data. The empirical findings revealed that during the COVID-19 pandemic, there was an increase in green finance for all banks and NBFIs compared to before the epidemic, indicating that the pandemic had no negative impact on the total green finance growth of all banks and NBFIs. On the other hand, compared to the pre-pandemic period, bank-wise growth in green financing was higher for state-owned commercial banks (SOCBs), specialized banks (SDBs), and private commercial banks (PCBs) but lower for foreign-owned commercial banks (FCBs) during the COVID-19 epidemic. This suggests that the pandemic does not affect the expansion of green finance by SOCBs, SDBs and PCBs but significantly impacted the growth of green financing by FCBs. Furthermore, the research findings showed that the total outstanding and classified loans within the green finance investment decrease for both banks and NBFIs during the COVID-19 pandemic. The results indicated that the Bangladeshi banks’ level of automation towards green banking were satisfactory during the pandemic. Therefore, major policy implications for the green economic recovery by the government, BB, and managers of the banks and financial institutions in emerging economies like Bangladesh were discussed.

According to the model of proactive motivation, we constructed a moderated impact model to examine the relationship between employees perceived overqualification (POQ), transformational leadership (TL), constructive deviant behaviour (CDB), and the generational differences in their relationships. We examined research hypotheses using data of 525 individuals. Results revealed that POQ positively affects CDB, and TL strengthened the effect of POQ on positive toward CDB. Furthermore, the effect of POQ on CDB is strongest among individuals born in the 1980s, followed by those born in the 1990s, and the moderating effect of TL is strongest among individuals born in the 1980s, and not significant among those born in the 1990s. Implications, limitations, and future directions of the present study are discussed.

Tengchongite is a uranyl molybdate uranium mineral and it was found and named by Chen 1985.No more scholars studied on tengchongite after Chen’s work, The identification of this mineral has only been confirmed by single crystal X-ray diffraction. In the paper, micro laser Raman spectroscopy and infrared spectroscopy are used to identify the spectroscopy properties of tengchongite. The studies fill in the gaps of more than 30 years in terms of the molecular spectroscopy research of tengchongite. The mineral has an ideal model of Ca(UO₂)₆(MoO₄)₂O₅•12H₂O its bands attributed to the vibrating units are clearly identified in the Raman spectrum. Symmetric stretching modes at 812 cm^-1 and 839 cm^-1 are assigned to ν1 (UO₂)²⁺ ,The ν3 antisymmetric stretching modes of (UO₂)²⁺ are observed at 896 cm^-1, Symmetric stretching modes at 419^-1 and 440 cm^-1 are assigned to ν2 (UO₂)²⁺ .Symmetric stretching modes at 919cm-1 are assigned to ν1(MoO₄)^2-,The ν3 antisymmetric stretching modes of (MoO₄)^2- are observed at 752 cm^-1, the in-plane ν2(MoO₄)^2-and the out-of-plane ν4(MoO₄)^2- bending modes are at 169 cm^-1 and 254 cm^-1. IR spectrum of tengchongite shows the major uranyl band at 858 cm^-1 and 693 cm^-1, Mo-O bonds are observed at about 985 cm^-1 and 780 cm^-1, and H₂O groups are present with a wide range peaks from 3100 cm^-1 to 3500 cm^-1 and 1647 cm^-1, and the band at 1432.4 cm^-1 is probably due to the stretching vibration hydroxyl (OH^-1), therefore, tengchongite contains may include hydroxyl and its chemical formula needs to be modified .

Pipe leakage is an inevitable phenomenon in water distribution networks (WDNs), leading to energy waste and economic damage. Leakage events can be reflected quickly by pressure values, and the deployment of pressure sensors is significant for minimizing the leakage ratio of WDNs. Concerning the restriction of realistic factors, including project budgets, available sensor installation locations, and sensor fault uncertainties, a practical methodology is proposed in this paper to optimize pressure sensor deployment for leak identification in terms of these realistic issues. Two indexes are identified to evaluate the leak identification ability, that is, detection coverage rate (DCR) and total detection sensitivity (TDS), and the principle is to determine priority to ensure an optimal DCR and retain the largest TDS with an identical DCR. Leakage events are generated by a model simulation and the essential sensors for maintaining the DCR are obtained by subtraction. In the event of a surplus budget, and if we suppose the partial sensors have failed, then we can determine the supplementary sensors that can best complement the lost leak identification ability. Moreover, a typical WDN Net3 is employed to show the specific progress, and the result shows that the methodology is largely appropriate for real projects.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

In this study, a novel oral formulation of berberine hydrochloride (BBH) hydrogel was successfully synthesized through physical cross-linking using chitosan (CS) and carboxymethyl-β-cyclodextrin (CMCD). The characterization results confirmed the successful synthesis of CS/CMCD hydrogel and the subsequent loading of BBH into this composite (CS/CMCD/BBH) was effectively accomplished. BBH was used as a model drug and the resulting hydrogel demonstrated a sustained drug release profile. In addition to its improved solubility and sustained release characteristics, the hydrogel exhibited excellent antibacterial activity against common pathogens such as Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), and Candida albicans (C. albicans). Additionally, in vitro studies indicated that the hydrogel was not cytotoxic to NIH3T3 and HaCaT cells, suggesting its safety for biomedical applications. This lack of cytotoxic effects, combined with the mechanical strength, solubility improvements, and antibacterial properties of the hydrogel, positions the CS/CMCD/BBH hydrogel as a promising candidate for effective oral delivery of BBH. By addressing the solubility and delivery challenges of BBH, this hydrogel offers a viable solution for the oral administration of berberine hydrochloride, with potential applications in various biomedical fields.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

Excessive CO₂ emissions and alternative energy fuels are two major difficult issues. The utilization of CO₂ into fine chemicals is an optimal route. Diethyl carbonate (DEC) is an extremely versatile chemical intermediate. DEC is used in gasoline, pharmaceutical, chemical and other fields. DEC synthesis from CO₂ and ethanol is a typical green synthetic route. Ni-Cu@Na₃PW₁₂O₄₀ catalysts were synthesized by two novel methods of supported and mixed. The catalyst prepared by mixed method showed nice catalytic performance. It was confirmed that water removal was the key to improving conversion efficiency. In the presence of dehydrating agent of ethylene, ethanol conversion increased from ca. 3% to ca. 40%. Propylene oxide (PO) was participated in the reaction and ethanol conversion continued to reach to ca.90% while DEC selectivity dropped by half. Under optimal conditions, our Ni-Cu@Na₃PW₁₂O₄₀ catalyst effectively solved the two major issues above.

The digital orthophoto is an image with geometric accuracy and no distortion. It is acquired through a top view of the scene and finds widespread applications in map creation, planning, and related fields.This paper classifies the algorithms for digital orthophoto generation into two groups: explicit methods and implicit methods. Explicit methods rely on traditional geometric methods, obtaining geometric structure presented by explicit parameters with Multi-View Stereo (MVS) theories, as seen in our proposed Top view constrained Dense Matching (TDM). Implicit methods rely on neural rendering, obtaining implicit neural representation of scenes through the training of neural networks, as exemplified by Neural Radiance Fields (NeRF). Both of them obtain digital orthophoto by rendering from a top view perspective. In addition, this paper conducts an in-depth comparative study between explicit and implicit methods. The experiments demonstrate that both algorithms meet the measurement accuracy requirements and exhibit a similar level of quality in terms of generated results. Importantly, the explicit method shows a significant advantage in terms of efficiency, with a time consumption reduction of two orders of magnitude under our latest CUDA version TDM algorithm. Although explicit and implicit methods differ significantly in their representation forms, they share commonalities in the implementation across algorithmic stages. These findings highlight the potential advantages of explicit methods in orthophoto generation, while also providing beneficial references and practical guidance for the fast digital orthophoto generation using implicit methods.

In nature and engineering applications, flexible fiber beds covering biological surfaces can play a role in reducing resistance. These fibers deform under the action of fluids, and this deformation affects the fluid flow state, forming a complex fluid-solid interaction phenomenon. To quantitatively analyze such issues, the physical model is simplified to the deformation problem of an soft hair bed caused by Stokes flow, and the deformation problem of a single fiber caused by Stokes flow is further studied. The deformation problem of an elastic single fiber in a channel caused by Stokes flow can be described by a nonlinear integral equation. We have obtained a new series solution, which has been compared with the previous perturbation method to verify the accuracy and effectiveness of the series solution. Meanwhile, we have further provided an extended form of flexible fiber deformation through experimental fitting. This fluid-solid interaction problem involves multiple fields and is very important in many natural and engineering systems. The research in this paper can not only help us better understand complex phenomena in nature but also delve into the interaction mechanism between fluids and solids, providing a theoretical basis for future scientific research and engineering applications.

Previous studies had shown that mRNA, miRNA and lncRNA were associated with cardiovascular diseases. The study was aimed to explore the differential expressions of mRNA, lncRNA and miRNA between coronary artery disease (CAD) and healthy control, and their interaction in CAD. We investigated the differential expression of ceRNA between CAD and healthy control through data collected from Gene Expression Omnibus (GEO) microarrays. Furthermore, we investigated the biological function of these differential expressions of ceRNAs by Gene Ontology (GO), Kyoto Encyclopedia of Genes and Genomes (KEGG) analyses. Protein-protein interaction (PPI) network was created to identify the hub genes. Biosystems and literature search were performed for signaling pathways and their function of the included differential expression ceRNAs. A total of 456 miRNA expression profiles, 16,325 mRNA expression profiles, and 2,869 lncRNA expression profiles were obtained. Eleven Go and KEGG pathways (count ≥9), top 15 of PPI network node connectivity rank, and top 15 of ceRNA network node degree centrality rank were achieved at the statistical significance level (P<0.05). We further identified that several differential expressions of ceRNAs and their signaling pathways were associated with CAD through biosystems and literature search. Based on eleven Go and KEGG pathways, top 15 of PPI network node connectivity rank, and top 15 of ceRNA network node degree centrality rank in CAD population, our findings would contribute to further exploration for the molecular mechanism of CAD.

BACKGROUND. The aims of this study was to compare differences in daytime sleepiness between genders and qualification levels in a cohort university Chinese soccer player under 0 Covid policy restrictions in the urban area of Shanghai. METHODS. 491 questionnaires of Epworth Sleepiness Scales (ESS) were compiled online by males and females Soccer Students (SS), Semi-professional players (SP) and professional players (PP) during the ongoing measures of Shanghai lockdown. ANOVA was performed for players levels and gender. RESULTS. Significant differences were found between the 3 levels and between males and females. PP showed a very low score in the ESS (5,97) well below the threshold of 8, while SS and SP showed an ESS score above the threshold. Female showed higher scores than males. CONCLUSIONS. This study present the first data on sleepiness in Chinese soccer players of different level of qualification in a lockdown condition. Professional players has been less affected by lockdown measures than SS and SP. We can hypothesize the reasons resides in the more ordered lifestyle of PP in comparison to SS and SP, which mitigated the effects of the lockdown. Measures to improve sleep in females’ soccer player should be adopted.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

The pop-in effect in nanoindentation of metals represents a major collective dislocation phenome-non that displays sensitivity in the local surface microstructure and residual stresses. To under-stand the deformation mechanisms behind pop-ins in metals, large scale molecular dynamics simulations are carried out to investigate the pop-in behavior and indentation size effect in unde-formed and deformed Cu single crystals. Tensile loading, unloading and reloading simulations are performed to create a series of samples subjected to a broad range of tensile strains with/without pre-existing dislocations. The subsequent nanoindentation simulations are con-ducted to study the coupled effects of pre-strain, the presence of resulting dislocations and surface morphology, as well as indenter size effects on the mechanical response in indentation processes. Our work provides detailed insights into the deformation mechanisms and microstruc-ture-property relationships of nanoindentation in the presence of residual stresses and strains.

Translation is spatiotemporally regulated and ER-associated mRNAs are generally in efficient translation. It is unclear whether the ER-associated mRNAs are deadenylated or degraded on the ER surface in situ or in the cytosol. Here, we showed that ER possessed active deadenylases, particularly the poly(A)-specific ribonuclease (PARN), in common cell lines and mouse tissues. Consistently, purified recombinant PARN exhibited a strong ability to insert into the Langmuir monolayer and liposome. ER-anchored PARN was found to be able to reshape the poly(A) length profile of the ER-associated RNAs by suppressing long poly(A) tails without significantly influencing the cytosolic RNAs. The shortening of long poly(A) tails did not affect global translation efficiency, suggesting that the non-specific action of PARN towards long poly(A) tails was beyond the scope of translation regulation on the ER surface. Transcriptome sequencing analysis indicated that the ER-anchored PARN trigged the degradation of a small subset of ER-enriched transcripts. The ER-anchored PARN modulated the translation of its targets by redistributing ribosomes to heavy polysomes, suggesting that PARN may play a role in dynamic ribosome reallocation. During DNA damage response, MK2 phosphorylated PARN-Ser557 to modulate PARN translocation from the ER to cytosol. By promoting the decay of ER-associated MDM2 transcripts with low ribosome occupancy, the ER-anchored PARN modulated DNA damage response and thereby cell viability. These findings revealed that a highly regulated communication between mRNA degradation rate and translation efficiency is present on the ER surface in situ and that PARN may contribute to this communication by modulating the dynamic ribosome reallocation between transcripts with low and high ribosome occupancies.

The arranged paths of dominoes have many shapes. The scaling law for the propagation speed of domino toppling has been extensively investigated. However, in all previous investigations, the scaling law for the velocity of domino toppling motion in curved lines was not taken into account. In the present work, the finite-element analysis (FEA) program ABAQUS was used to study the velocity of domino toppling motion in curved lines. It is shown that the domino propagation speed has a rising trend with increasing domino spacing in a straight line. It is also found that domino propagation speed is linearly proportional to the square root of domino separation. This research proved that the scaling law for the speed of domino toppling motion given by Sun (2020) is true [B-H. Sun, 2020. Scaling law for the propagation speed of domino toppling. AIP Advances, 10(9),095124.]. Moreover, the shape of domino arrangement paths has no influence on the scaling law for the propagation speed of dominoes but can affect the coefficient of the scaling law for the velocity. Therefore, the amendatory function for the propagation speed of dominoes in curved lines was formulated by the FEA data. The fitted amendatory function, $\varphi_{revise}$, provides the simple method for a domino player to quickly estimate the propagation speed of dominoes in curved lines.

This paper presents three types of tensor Conjugate-Gradient methods for solving large-scale linear discrete ill-posed problems based on the t-product between third-order tensors. An automatical determination strategy of a suitable regularization parameter is proposed for the tensor conjugate gradient (tCG) method. A truncated version and a preprocessed verion of the tCG method are further presented. The discrepancy principle is employed to determine a suitable regularization parameter. Several numerical examples are given to show the effectiveness of the proposed tCG methods in image and video restoration.

Abstract: There are a large number of cross-linked chemical bonds such as tight disulfide bonds, hydrogen bonds,and salt bonds in keratin, which makes it difficult to break the structural stability of the protein using conventional methods. The degradation of feather waste using keratinases produced by microorganisms has the advantage of being efficient and environmentally friendly. In this study, 23 strains capable of producing transparent circles were obtained via preliminary screening with skim milk as the sole carbon and nitrogen source, and 9 strains capable of degrading feathers were obtained via rescreening with feathers as the sole carbon and nitrogen source. Finally, through the determination of enzyme activity, the strain CY-A with a high ability to degrade feathers was obtained. The strain was identified as Bacillus tequilensis via morphological observation, physiological and biochemical identification, and 16 S rRNA molecular biology. The keratinase gene (bta) of Bacillus tequila was cloned, and its full-length gene sequence was 1110 bp, containing an open reading frame of 1089, encoding 369 amino acids (GeneBank accession number OR733336). The physicochemical properties, secondary structure, and tertiary structure of the recombinant protein were analyzed using bioinformatics tools such as ProtParm, SOPMA, MEGA, and SWISS-MODELS. It was found that the relative molecular mass was 37.953 kD and that the isoelectric point was 8.48. The protein was a hydrophilic protein. The keratinase bta gene was ligated to the expression vector pET28a(+) using T4 ligase, and the recombination expression plasmid pET28-bta was constructed and transformed into E. coli BL21(DE3) to obtain recombinant engineered bacteria. The expressed keratinase was purified using a Ni2+ affinity chromatography column to obtain recombinant bta keratinase bta with a molecular weight of 37.953 kD. The identification and characterization of this keratinase gene provides some theoretical basis for the further enhancement of keratinase activity by means of genetic engineering.

p53 is among the most frequently mutated tumor suppressor genes given its prevalence in >50% of all human cancers, including high grade serous endometrial cancers and ovarian cancers. In addition to loss of tumor suppression function, many mutated p53 (Mutp53) proteins acquire gain-of-function (GOF) activities as oncogenes to promote cancer progression, which manifest through aberrant expression of p53. As we have come to see, statins induce CHIP-mediated degradation of mutp53 by blocking the interaction between mutp53 and DNAJA1. Therefore, targeting critical downstream pathways of mutp53 provides an alternative strategy for treating cancers expressing mutp53. In this review, we summarize recent advances with Wee1 inhibitors and mevalonate pathway inhibitors, particularly statins, regarding their use in gynecological cancers with p53 mutations.

Whether and how P2X7 receptor knockout (KO) modulates central post-stroke pain (CPSP) induced by lesions of the ventrobasal complex (VBC) of the thalamus regarding behavioral, molecular, and electrical recording parameters remains unclear. Following the experimental protocols of a rat hemorrhage CPSP model, the VBC of the thalamus of wild-type and P2X7 receptor KO mice was injected with 10 mU/0.2 μl type IV collagenase to produce an animal model of stroke-like thalamic hemorrhage. Behavioral data showed that the CPSP group induced thermal and mechanical pain, while the P2X7 receptor KO group showed reduced thermal and mechanical pain behaviors. Molecular assessments revealed that the CPSP group had lower expression of NeuN and KCC2 and higher expression of GFAP, IBA1, and BDNF. The P2X7 KO group showed lower expression of GFAP, IBA1, and BDNF and higher expression of KCC2 than the CPSP group. The expression of NKCC1, GABAa receptor, and TrkB did not differ significantly between the control, CPSP, and P2X7 receptor KO groups. Muscimol application increased multiunit numbers and [Cl-] influx in the membrane in the CPSP group, while P2X7 receptor KO reduced multiunit activity and [Cl-] outflux. P2X4 receptor expression was significantly decreased in the 100 kb but not the 50 kb site in the P2X7 receptor KO group. Altogether, the P2X7 hypothesis of CPSP was proposed, wherein P2X7 receptor KO changed the CPSP pain behavior, numbers of astrocytes and microglia, CSD amplitude of the anterior cingulate cortex and the medial dorsal thalamus, BDNF and KCC2 expression, [Cl-], and P2X4 activation in 100 kb with P2X7 receptors. The present findings have implications for the clinical treatment of CPSP symptoms.

Postprandial plasma glucose between 4 and 7.9 hours is associated with the diagnosis of diabetes, diabetes mortality, and cardiovascular mortality. However, it is unknown whether 2-hour plasma glucose during the oral glucose tolerance test conducted in this postprandial period (4–7.9 hours), termed as 2-h PGOGTT@4–7.9h, can accurately classify diabetes diagnosis and predict mortality risks. This study aimed to address these questions using 2,347 adult participants. Diabetes was defined as HbA1c ≥6.5%, and the ability of 2-h PGOGTT@4–7.9h to classify diabetes was analyzed using receiver operating characteristic curves. Cox proportional hazards models were employed to estimate mortality hazard ratios (HRs) and 95% confidence intervals (CIs). The results showed that 2-h PGOGTT@4–7.9h could classify diabetes with 92% accuracy. Participants were followed up for a mean of 21.4 years. A 1-natural-log higher 2-h PGOGTT@4–7.9h was associated with an increased risk of mortality from diabetes (adjusted HR, 21.1; 95% CI, 9.2–48.0) and cardiovascular disease (adjusted HR, 1.47; 95% CI, 1.13–1.91). Simulation analysis indicated that future studies may require at least 100 participants to investigate 2-h PGOGTT@4–7.9h for diabetes diagnosis. In conclusion, 2-h PGOGTT@4–7.9h may be useful for diabetes classification and prediction of mortality risk.

As a typical visual positioning system, monocular ranging is widely used in various fields. However, when the distance increases, there is a greater error. YOLOv8 network has the advantages of fast recognition speed and high accuracy. This paper proposes a method by combining YOLOv8 network recognition with a monocular ranging method to achieve target localization and grasping for the NAO robots. By establishing a visual distance error compensation model and applying it to correct the estimation results of the monocular distance measurement model, the accuracy of the NAO robot's long-distance monocular visual positioning is improved. Additionally, a grasping control strategy based on pose interpolation is proposed. Throughout, the proposed method's advantage in measurement accuracy was confirmed via experiments, and the grasping strategy has been implemented to accurately grasp the target object.

This paper explores the application of wavelet analysis, a multiscale approach for enhancing visual clarity, in the context of image denoising, which reduces the impact of noisy pixels, caused by various factors such as electronic sensor limitations, low-light conditions, or transmission errors in digital imaging systems. This paper introduces some common noise types like Gaussian noise and processes of image denoising, eliciting the strength of wavelet analysis. As a powerful image denoising technology, wavelet analysis needs five steps to process the image, and the key step is thresholding. There are many kinds of wavelet, and each wavelet has different advantages and functions, which makes it suitable for different applications. Hence, wavelet analysis also makes a contribution in various fields beyond signal processing and data analysis, such as Biomedical Imaging and Geophysics and Seismology, where preserving image quality is essential for accurate analysis and interpretation. In short, this research highlights the promise of wavelet analysis, emphasizing the use of high- quality image data.

Urban morphology exhibits fractal characteristics, which can be described by multifractal scaling. Multifractal parameters under positive moment orders primarily capture information about cen-tral areas with relatively stable growth, while those under negative moment orders mainly reflect information about marginal areas with more active growth. However, effectively utilizing mul-tifractal spectrums to uncover the spatio-temporal variations of urban growth remains a challenge. To addresses this issue, this paper proposes a multifractal measurement by combining theoretical principles and empirical analysis. To capture the difference between growth stability in central areas and growth activity in marginal areas, an index based on generalized correlation dimension Dq is defined. This index takes the growth rate of Dq at extreme negative moment order as the numerator, and that at extreme positive moment order as the denominator. During the stable stage of urban growth, the index demonstrates a consistent pattern over time. While during the active stage, the index may exhibit abnormal fluctuations or even jumps. This indicates that the index can reveal spatio-temporal information about urban evolution that cannot be directly observed through multifractal spectrums alone. By integrating this index with multifractal spectrums, we can more comprehensively characterize the evolutionary characteristics of urban spatial structure.

The purpose of this study is to examine the relationship between the institutional investors which can affect financial performance for corporate sustainability on the income smoothing. Therefore, this study focus on the connection between the nature of stock rights and income smoothing in China. For this study, hypotheses were established on the relationship each state-controlled companies, income smoothing, and information equilibrium of individual investors, and empirical analysis was conducted through related variables. The analysis results are summarized in three categories as follows. First, this research finds that state-controlled firms (CONTs) prefer income smoothing activities compared to non-state-controlled firms for the long-term sustainable development of firms using data from 2011 to 2019. Second, this study found out that Institutional investors support the behavior of CONTs to smooth their earnings because this behavior is seen as an attempt by CONTs to convey valuable private information to other investors. Third, we was able to discover that institutional investors' monitoring effect is predominantly driven by pressure-resistant institutional investors. This research complements the lack of empirical research on income smoothing and enable to give a guideline that the type of stock rights is a critical key determinant of participation in income smoothing activities for stable growth and sustainability in the future.

Rhododendron is well-known for the colorful corolla. Molecular marker systems have the potentials to elucidate genetic diversity as well as to assess the genetic fidelity in rhododendrons. In the present study, the reverse transcription domains of long terminal repeat retrotransposons were cloned from rhododendrons and used to develop inter-retrotransposon amplified polymorphism (IRAP) marker system. Subsequently, 198 polymorphic loci were generated from the IRAP and inter-simple sequence repeat (ISSR) markers, of which 119 were derived from the IRAP markers. It was justified that in rhododendrons, IRAP markers were superior to the ISSRs in some polymorphic parameters such as the average number of polymorphic loci (14.88 versus 13.17). In comparison with the single one, the combination of IRAPs and ISSRs systems was more discriminative for detecting 46 rhododendron accessions. Further, IRAP markers demonstrated more efficiency in genetic fidelity detection of in vitro R. bailiens, an endangered species just recorded in Guizhzhou Province, China. The available evidences revealed the distinct properties of IRAP and ISSR markers in the rhododendron-associated applications, and highlighted the availability of highly informative ISSR and IRAP markers in the genetic diversity evaluation and the genetic fidelity assessment of rhododendrons, which may facilitate the preservation and genetic breeding in rhododendron plants.

The shape of the knee is a chain-like structure of an ellipsoid. This suggests that, in the latest study, in addition to rolling, there is slippage in the motion of the knee. This paper selects a mechanical braking model for cattle based on two mechanical structures in different directions at the joints. The experimental results show that the modified dynamical system has strong chaotic properties. This can be one of the basis for judging various health states.

An automatic recognizing system of white blood cells can assist hematologists in the diagnosis of many diseases, where accuracy and efficiency are paramount for computer-based system. In this paper, we present a new image processing system to recognize the five types of white blood cells in peripheral blood with marked improvement in efficiency when juxtaposed against mainstream methods. The prevailing deep learning segmentation solutions often utilize millions of parameters to extract high-level image features and neglect the incorporation of prior domain knowledge, which consequently consume substantial computational resources and increase the risk of overfitting, especially when limited medical image samples are available for training. To address these challenges, we propose a novel memory-efficient strategy that exploits graph structures derived from the images. Specifically, we introduce a lightweight superpixel-based Graph Neural Network (GNN) and break new ground by introducing superpixel metric learning to segment nucles and cytoplasm. Remarkably, our proposed segmentation model (SMGNN) achieves state-of-the-art segmentation performance while utilizing at most 10000$\times$ less than the parameters compared to existing approaches. The subsequent segmentation-based cell type classification processes show satisfactory results that such automatic recognizing algorithms are accurate and efficient to execeute in hematological laboratories.

Chi-squared automatic interaction detector (CHAID) algorithm is considered to be one of the mostly used supervised learning methods as it is adaptable to solving any kind of problem at hand. We have been starkly aware of CHAID maps non-linear relationships quite well, and it can empower predictive models with stability. But we don’t know how high its accuracy is precisely. To find out the perfect scope CHAID algorithm fits into, this paper presents the analysis of the accuracy of the CHAID algorithm. We introduce the causes, applicable conditions and application scope of CHAID algorithm at first, and then highlight the difference of branching principal between the CHAID algorithm and several other common decision tree algorithms, which is our first step towards basic analysis on CHAID algorithm. We next employee an actual branching case to help us understand CHAID algorithm better. Specifically, we use vehicle customer satisfaction data to compare multiple decision tree algorithms, and cite some factors that affecting the accuracy and some corresponding countermeasures which are more conducive to us to obtain accurate results. The results show that CHAID can analyze the data very well, and detect the significantly correlated factors surely. In this paper, we learn the clear information required to understand CHAID algorithm, thereby make better choices when we need to use decision tree algorithms.

This general review assesses the impact of physical exercise on oxidative and nitrosative stress and the counteractive role of antioxidants, drawing from a systematic literature search up to March 2024 in databases like PubMed and Web of Science. The review highlights studies on the effect of exercise on the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) and antioxidant responses in both human and animal models based on rigorous inclusion and exclusion criteria. Due to the variety of exercise types and participants' characteristics, a narrative synthesis approach was adopted. The findings indicate that moderate exercise boosts antioxidant defenses, known as hormesis, whereas excessive physical activity may increase oxidative and nitrosative damage. The review also explores the complex effects of antioxidant supplementation, revealing that while natural dietary antioxidants support health, high-dose supplements could potentially hinder positive adaptations to exercise. Recommendations for athletes and the general active population highlight the importance of balancing exercise and dietary intake to optimize health benefits. The review concludes with a call for more detailed research on tailored exercise and nutrition plans to dissect these intricate relationships further.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

Spider silk has excellent strength and elasticity in natural, researchers have been working for decades try to achieve natural spider silk outstanding mechanical properties using recombinant spider silk protein (spidroin) through artificial spinning. In this work, we chose wet spinning method to explore the relationship between concentration of coagulation bath and fiber performance. It was found that the concentration of methanol has important effect on fiber continuity, diameter and mechanical properties. Lower concentration favors spinning continuous thinner, fibers with high strain. Secondary stretching benefits spinning silk fibers with stable mechanical properties, and thermal stability. Through applying different methanol concentration and additional stretching, we obtained silk fibers with Young’s modulus of 3.052± 2.626 GPa, stress of 25.3944 ± 17.48 MPa, and strain of 140 ± 95.4%.

Based on the major, trace element, and isotope data of the Cenozoic basalts in the study area, it is indicated that the basalts in this region can be classified into three distinct magma systems: alka-li basalts, tholeiite basalts, and Nushan alkali basalts. The geochemical characteristics observed in the studied basalts indicate that the mantle source in this region might have experienced met-asomatic processes prior to partial melting, which could be linked to an ancient subduction pro-cess. Combining the geochemical characteristics in the studied basalts with previous research, we propose that the underlying mantle source in Anhui province may have undergone metaso-matism due to the carbonatitic melts. These melts are believed to have originated from car-bonated eclogite, derived from subducted Pacific slab materials present in the deeper mantle. According to the Sr-Nd isotope data, it is suggested that the mantle source in the Nushan region could be derived from a depleted asthenospheric mantle, while the basaltic composition in the Niugang area may be representative of the mantle's end components associated with the EM-I enriched mantle source present in this study area. Therefore, we propose that the Anhui basalts may have originated from the partial melting of a mantle source representing a mixing of two end-members: DMM (Depleted MORB Mantle) and EM-Ⅰ (Enriched Mantle 1). The Anhui basal-tic magmas may have originated from the partial melting of EM-Ⅰ, potentially influenced by upwelling asthenospheric mantle or asthenospheric diapirism processes. The mantle source in the study area experiences partial melting at 1-5%, 15%, and 1-10%, resulting in the formation of parent magmas for alkali basalt, tholeiitic basalt, and Nushan alkali basalt. Subsequently, the parent magmas experienced fractional crystallization processes, which included minerals like olivine, pyroxene, and plagioclase. This led to the formation of various types of basalt in the study area.

Hydrogen sulfide (H₂S) is a novel gasotransmitter, sucrose (SUC) is both cellular energy and signaling molecule. However, their signaling interaction in maize thermotolerance is poorly known. In this study, using maize seedlings as materials, metabolic and functional interaction of H₂S and SUC in maize thermotolerance was investigated. Data show that under heat stress survival rate and tissue viability were increased by exogenous SUC, while malondialdehyde content and electrolyte leakage were decreased by SUC, indicating SUC could upraise maize thermotolerance. Also, SUC-upraised thermotolerance was enhanced by H₂S, while weakened by inhibitor (propargylglycine) and scavenger (hypotaurine) of H₂S and SUC-transport inhibitor (N-ethylmaleimide). To figure out underlying mechanism of H₂S-SUC interaction-upraised thermotolerance, redox parameters in mesocotyls of maize seedlings were measured before and after heat stress. The data display that activity and gene expression of H₂S-metabolizing enzymes were up-regulated by SUC, whereas H₂S had no significant effect on activity and gene expression of SUC-metabolizing enzymes. Besides, activity and gene expression of catalase, glutathione reductase, ascorbate peroxidase, peroxidase, dehydroascorbate reductase, monodehydroascorbate reductase, and superoxide dismutase were reinforced by H₂S, SUC, and their combination under non-heat and heat conditions in varying degrees. Similarly, content of ascorbic acid, flavone, carotenoid, and polyphenol was increased by H₂S, SUC, and their combination, whereas production of superoxide radical and hydrogen peroxide level were impaired by these treatments to different extent. These results imply that the metabolic and functional interaction of H₂S and sucrose exists in the formation of maize thermotolerance through redox homeodynamics.

We propose a novel plasmon nano-optical antenna that consists of three vertically superimposed discs with different materials. Two symmetrical nanometer-scale Yagi antenna elements with gold-material are embedded into the surface of the middle disc with silicon dioxide. Based on plasmon theory and Yagi antenna principle, we explore the properties of the far-field radiation and near-field transmission of the antenna in near infrared band. It is found that the pattern of the xoy plane in the antenna can be adjusted in arbitrary direction. The far-field pattern and near-field transmission spectrum can be reconfigured by changing the angle a of the Yagi antenna elements in the middle disc. Moreover, we also discuss the influences of the widths and lengths of the elements on the near-field transmission spectrum when a is fixed at 0 degree.

This study aimed to examine the association of blood triglyceride levels with fasting blood glucose levels and type 2 diabetes (T2D) prevalence in Chinese adults with normal triglyceride levels (<1.7 mmol/L), using linear regression and binary logistic regression, respectively. This cross-sectional study included 16,706 Chinese adults, among which 1,067 had T2D. Triglycerides were positively associated with fasting plasma glucose after multivariate adjustment (β=0.034, P<0.001). One natural log unit increase in blood triglycerides was associated with a 61% higher multivari-ate-adjusted risk of T2D (odds ratio [OR], 1.61; 95% confidence interval [CI], 1.19-2.17; P=0.002). The positive associations remained when participants who were treated with lipid-lowering or an-ti-diabetic drugs were excluded. The optimal cut-off of triglycerides for T2D was 1.09 mmol/L (obtained using Receiver Operating Characteristic curve analysis). Participants with triglycerides of ≥1.09 mmol/L had a 28% higher risk of T2D (OR, 1.28; 95% CI, 1.07-1.53; P=0.006) compared to those with triglycerides below the cut-off. In conclusion, this study showed that, in people with normal triglyceride levels, triglycerides at the upper normal range correlated with increased T2D diagnosis risk, with an optimal cut-off of 1.09 mmol/L. Therefore, adults with high “normal” triglyceride levels (1.09-1.69 mmol/L) may need to be closely monitored for the development of T2D.

The joint extraction of entities and relations is a critical task in information extraction, and its performance directly affects the performance of downstream tasks. However, existing joint extraction models based on deep learning exhibit weak processing capabilities for the phenomenon of multiple pronunciations of one character and multiple characters of one pronunciation when processing Chinese texts, resulting in performance loss. To address these issues, this paper introduces part-of-speech (POS) and pinyin features to aid the model in learning semantic features that are more contextually appropriate. A Chinese Joint Entity and Relation Extraction Model based on Progressive Contrastive Learning and Heterogeneous Feature Fusion is proposed (CJE-PCHF). During model training, an interactive fusion network based on progressive contrastive learning is employed to learn the dependencies between pinyin, POS, and semantic features. This guides the model in heterogeneous feature fusion, capturing higher-order semantic associations between heterogeneous features. On the commonly used DuIE evaluation dataset for joint extraction, this model achieved a significant improvement, with the F1 score increasing by 5.4% compared to the benchmark model CasRel.

The steel grid structure with bolted ball joints is gaining popularity in offshore platforms and aquaculture cages, but the corrosion resistance of these joints is a critical safety concern. This article introduces an innovative method to enhance the sealing performance of bolted ball joints, preventing seawater ingress and corrosion. The approach involves creating a sealed surface within the contact gap between the sleeve and connecting components. Circular grooves and sealing washers are added to both ends of the sleeve. A two-dimensional finite element analysis model of the bolted ball joint with the sealing structure was created using SOLIDWORKS and ANSYS. The study analyzes the sealing gasket's contact pressure at various compression levels and evaluates its performance with bubble tests for air tightness. Research results show a linear relationship between contact pressure and compression rate, with a sealing pressure of 5.95MPa achieved at a 14% compression rate. This simple, cost-effective sealing method effectively prevents corrosion from seawater, making it ideal for marine environments.

Gross strap muscle invasion (gSMI) in patients with differentiated thyroid cancer (DTC) was defined as high-risk recurrent group in the 2015 American Thyroid Association guidelines. However, controversy persists because several studies suggested gSMI had little effect on disease outcome. Herein, a systematic review and meta-analysis was conducted to investigate impact of gSMI on outcome of DTC. Methods: A systematic search of electronic databases (PubMed, EMBASE, Cochrane Library, and MEDLINE) for studies published until February 2020 was performed. Case-control studies and randomized controlled trials that studied the impact of gSMI on outcome of DTC were included. Results: Six studies (all retrospective studies) involving 13639 patients met final inclusion criteria. Compared with no extrathyroidal extension (ETE), patients with gSMI were associated with increased risk of recurrence (P=0.0004,OR, 1.46; 95% CI: 1.18 to 1.80) and lymph node metastasis (LNM) (P<0.00001,OR 4.19;95% CI. 2.53 to 6.96). For mortality (P=0.34,OR 1.47;95% CI:0.67 to 3.25), ten-year disease-specific survival (P=0.80, OR 0.91;95% CI:0.44 to 1.88) and distant metastasis (DM) (P=0.21, OR 2.94;95% CI. 0.54 to 15.93), there was no significant difference between gSMI and no ETE group. In contrast with maximal ETE, patients with gSMI were associated with decreased risk of recurrence (P<0.0001,OR, 0.58; 95% CI: 0.44 to 0.76) , mortality (P=0.0003,OR 0.20;95% CI:0.08 to 0.48), LNM (P=0.0003,OR 0.64;95% CI. 0.50 to 0.81) and DM (P=0.0009,OR 0.28;95% CI. 0.13 to 0.59). Conclusions: DTC patients with gSMI had a higher risk of recurrence and LNM than those without ETE. However, in contrast with maximal ETE, a much better prognosis was observed in DTC patients with only gSMI. The findings of our meta-analysis provide supportive evidence for the validity of the T category changes in the 8th edition American Joint Committee on Cancer system. The actual impact of gSMI should be re-evaluated and revised in the recurrent risk stratification system in the future.

In order to solve the problem of many constraints and complex navigation environment in the path planning of unmanned surface vehicle(USV), an improved Sparrow search algorithm com-bining Cubic chaotic map and Gaussian random walk strategy was proposed to plan it. Firstly, in the population initialization stage, Cubic chaotic map was used to replace the random generation method of the traditional sparrow search algorithm to optimize the uneven initial distribution of the population and improve the global search ability of the population. Secondly, in the late it-eration of the algorithm, the standard deviation of fitness is introduced to determine whether the population is trapped in the local optimum. If true, the Gaussian random walk strategy is used to perturb the optimal individual and assist the algorithm to escape the local optimum. Thirdly, the chosen water environment is modeled, and the navigation information of the original inland electronic navigation chart(ENC) is preprocessed, gridized, and the obstacle swelling is processed. Finally, the path planning experiments of USV are carried out in inland ENC grid environment. The experimental results show that, compared with the traditional sparrow search algorithm, the average fitness value of the path planned by improved sparrow search algorithm is reduced by 14.8%, and the variance is reduced by 49.9%. The path planned by the algorithm is of good quality and high stability, and combined with ENC, it can provide a reliable path for USV.

Orchids are often a mystery because of their close and complex relationships with various microorganisms in the natural environment. Orchids rely on microorganisms to obtain nutrients, affecting their seed germination, protocorm, and adult plant growth. Currently, the majority of relevant research is concentrated on isolating and identifying environmental microorganisms that support orchid development and growth. With the development of metagenomic technology, our understanding of orchid mycorrhizal fungi (OMF) and root-associated bacteria (RAB) has been expanded. New research results and discoveries have emerged, which require a comprehensive assessment to provide a reference for studying microorganisms related to orchids. Therefore, we present a comprehensive summary, identifying significant inadequacies of present methodologies while providing ideas for further research.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

In light of the accelerated pace of economic growth and urbanisation, the transformation of green buildings has emerged as a prominent area of re-search. A considerable number of existing buildings have been constructed and are still in use. However, the energy consumption and environmental impact throughout the entire life cycle of these buildings are not adequately considered in the renovation design. This results in high energy consumption and poor indoor comfort. In this work, we include improving the thermal insulation of buildings, such as thickening the insulation of external walls and replacing energy-efficient windows to reduce energy losses caused by temperature differences between in-door and outdoor buildings; Adopt energy-efficient HVAC systems to reduce en-ergy consumption and improve indoor air quality by upgrading equipment effi-ciency, optimizing duct design, and intelligent control systems; At the same time, we will introduce renewable energy sources such as solar energy, and we will not only install solar photovoltaic panels to generate electricity, but also use solar thermal collector systems to provide hot water and heating, so as to achieve di-versified and sustainable use of energy. Combined, these measures can effec-tively reduce the overall energy consumption of the building, reduce carbon emissions, and improve the comfort and health of the indoor environment. During the experimental analysis, the energy consumption and indoor comfort before and after the renovation were evaluated, and the results showed that the energy consumption was significantly reduced and living comfort was improved.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

Global climate change, dominated by climate warming, is seriously affecting the balance of global ecosystems, but the risk of species extinction is particularly high in low-altitude mountain areas. To clarify the response of the endemic and critically endangered species Ilex nanchuanensis to climate change, this study used the MaxEnt model to simulate and predict the potential habitat of I. nanchuanensis during the Last Interglacial, Last Glacial Maximum, the current period, and two future periods (the 2050s and 2070s). The results showed that the hottest monthly minimum temperature is the most important climatic factor affecting the geographical distribution of I. nanchuanensis. Furthermore, I. nanchuanensis will be at risk of population shrinkage and extinction in the future, with the center of mass moving further northwest as concentrations of greenhouse gases increase, especially in the 2070s, when its geographical distribution shrinks the most under the RCP6 scenario. Global warming is causing habitat degradation for many species and will continue to migrate to higher altitudes and latitudes in the future, seriously affecting the global ecosystem balance. Therefore, to actively respond to the impacts of climate change, protected areas should be established around the geographical distribution centers of species, and core, buffer, and experimental areas should be scientifically and rationally delineated for the conservation and cultivation of germplasm resources.

Late onset Pompe disease is a recessive lysosomal storage disease. Clinical features include skeletal muscles deficiency and diaphragm weakness. Clinical management relies on supportive treatment and mechanical ventilation in patents with chronic respiratory failure. M mode ultrasound and tissue Doppler imaging can be used to assess and to follow up diaphragm function.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

Glaucoma, a global leading cause of blindness, necessitates accurate segmentation of the optic disc (OD) and optic cup (OC) for effective screening. However, existing segmentation methods based on convolutional neural networks (CNNs) suffer from high computational complexity and long inference times. In this paper, we propose an end-to-end segmentation method for the OD and OC using a lightweight MobileNetv3 as the feature extraction network. Our approach incorporates boundary branches and an adversarial learning network to achieve multi-label segmentation of the OD and OC. We evaluate the proposed method on three publicly available datasets: Drishti-GS, RIM-ONE-r3, and REFUGE. The experimental results demonstrate segmentation accuracies of 0.974/0.900, 0.966/0.875, and 0.962/0.880 for the OD and OC on the respective datasets, while significantly reducing inference time.

(1) Background: In most cases, passive isolation control methods are commonly used for the seismic isolation design of bridge engineering. However, for passive seismic isolation devices, due to their non-adjustable performance parameters, it is challenging to achieve a good seismic isolation effect for structures under random and variable seismic loads in the wide frequency range of 0 Hz to 20 Hz; (2) Methods: the sensitivity of the design parameters of the seismic isolation bearing was analyzed using the optimization center gradient method, and an improved genetic algorithm was employed to quickly optimize and obtain the optimal design parameters; (3) Results: the effectiveness of the three-dimensional seismic isolation bearing was validated through experiments. (4) Conclusions: The multi-factor sensitivity analysis approach used in this study for designing novel isolation bearings is applicable not only to seismic design in bridges but also serves as a reference for parameter design in isolation bearings requiring medium to high precision in seismic performance.

Utilizing ecological engineering to manage pests by enhancing the biological control function of natural predators through the selection of high-efficiency bank plants and the establishment of bank plant systems within agricultural ecosystems is an optimal strategy. While bank plant systems have found widespread use in greenhouse crop cultivation, their application in rice fields remains limited. This study aimed to assess the efficacy of Leersia sayanuka as a bank plant for controlling planthoppers and to explore the potential of sesame as a complementary plant to enhance the effectiveness of the bank plant system through field trials. The findings revealed that planting a strip of L. sayanuka, at least 50 cm wide and extending over 1 m in length, had a notable impact on planthopper control in paddy fields. Moreover, the incorporation of Sesamum indicum, a nectar plant, into the bank plant system consisting of L. sayanuka, Nilaparvata muiri, and Anagrus nilaparvatae, led to a significant increase in the population of Anagrus spp. in rice fields. This increase was accompanied by a rise in the egg parasitism rate targeting rice planthoppers, resulting in a marked improvement in overall rice planthopper control in paddy fields. Thus, the combined system demonstrated efficiency as an effective bank plant system for managing rice planthoppers.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

In order to better plan new or update sewer pipe condition assessment protocols, this paper presents systematic comparisons of four most widely-used sewer condition assessment protocols, including the fourth edition of Sewer Rehabilitation Manual (SRM-4) in UK, Pipeline Assessment and Certification Program (PACP) in America, Sewer Physical Condition Grading Protocols (SPCCM) in Canada, and Technical Specification for Inspection and Evaluation of Urban Sewer (TSIEUR) in China. In qualitative comparison, the defects, deduct values and assessment methods of the four protocols were analyzed; in quantitative comparison, protocols were used to evaluate the same 182 sewer pipe segments based on field data and the assessment results were compared. It was found that SRM-4 are the most optimistic with 59% pipes being Grade 1 and Grade 2, while SPCCM gives the most pessimistic results with 62% pipes being Grade 3 and Grade 4. Assessment results by PACP and TSIEUR are in the middle. The main reasons for the different evaluation results were due to the different weight of defect and evaluation methods used.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (&gt;0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (&lt;0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size &gt;100 μm, and soil structure was the most stable.

This paper extends the concept of weighted graphs to matrix weighted graphs. The consensus algorithms dictate that all agents reach consensus when the weighted graph is connected. However, it is not always the case for matrix weighted graphs. The conditions leading to different types of consensus have been extensively analysed based on the properties of matrix-weighted Laplacians and graph theoretic methods. However, in practice, there is concern on how to pick matrix-weights to achieve some desired consensus, or how the change of elements in matrix weights affects the consensus algorithm. By selecting the elements in the matrix weights, different clusters may be possible. In this paper, we map the roles of the elements of the matrix weights in the systems consensus algorithm. We explore the choice of matrix weights to achieve different types of consensus and clustering. Our results are demonstrated on a network of three agents where each agent has three states.

In the context of global climate change, the frequency of sudden natural disasters is increasing. Assessing traffic road damage post-disaster is crucial for emergency decision-making and disaster management. Traditional ground observation methods for evaluating traffic road damage are limited by the timeliness and coverage of data updates. Relying solely on these methods does not adequately support rapid assessment and emergency management during extreme natural disasters. Social media, a major source of big data, can effectively address these limitations by providing more timely and comprehensive disaster information. Motivated by this, we utilized multi-source heterogeneous data to assess the damage to traffic roads under extreme conditions and established a new framework for evaluating traffic roads in cities prone to flood disasters caused by rainstorms. The approach involves several steps: First, extracting the surface area affected by precipitation using a threshold method constrained by confidence intervals derived from microwave remote sensing images; Second, collecting disaster information from the Sina Weibo platform, where social media information is screened and cleaned. A quantification table for road traffic loss assessment was defined, and a social media disaster information classification model combining text convolutional neural networks and attention mechanisms was proposed (TextCNN-Attention Disaster Classification); Finally, matching traffic road information on social media with basic geographic data, visualizing the classification of traffic road disaster risk levels, and completing the assessment of traffic road disaster levels based on multi-source heterogeneous data. Using the "7.20" rainstorm event in Henan Province as an example, this study categorizes the disaster impact on traffic roads into five levels: particularly severe, severe, moderate, mild, and affected, as interpreted from remote sensing images. The evaluation framework for flood disaster traffic roads based on multi-source heterogeneous data provides important data support and methodological support for enhancing disaster management capabilities and systems.

To explore the relevant factors that affect the efficacy of consciousness-regaining therapy (CRT)for prolonged disorder of consciousness(pDOC),a retrospective analysis was conducted on the case data of 114 patients with pDOC admitted to department of functional neurosurgery of Tianjin Huanhu Hospital from January 2019 to January 2022. Basic information on the cases,data on pDOC disease assessment, consciousness-regaining therapy methods, and efficacy evaluation were collected. A total of 114 patients were grouped and compared based on the efficacy at the end of treatment. Among them, there were 61 cases in the ineffective group and 53 cases in the effective group. There was no statistically significant difference (P&gt;0.05) between the two groups in terms of gender, age, etiology, acute cerebral herniation, emergency craniotomy surgery, emergency decompressive craniectomy, time from onset to start of consciousness-regaining therapy , and duration of consciousness-regaining therapy(P&gt;0.05). However, there were statistically significant differences (P&lt;0.05) in terms of secondary hydrocephalus, , consciousness-regaining therapy methods, CRS-R grading before treatment, and GOSE score at 6 months after treatment. Binary logistic regression analysis showed that the type of therapy (OR=0.169, 95% CI: 0.057-0.508) was a related factor affecting the efficacy of consciousness-regaining therapy (P&lt;0.05).Compared with non-invasive therapy, personalized awakening therapy using various invasive consciousness-regaining therapy methods can help improve the efficacy of therapy for pDOC.

In-situ observation on the austenite grain growth and martensite transformation in a developed NM500 wear-resistant steel were conducted on a Confocal Laser Scanning High-temperature Microscope (CSLM). Results indicated that the martensite nucleation did not synchronously proceed during quenching process. The selective prenucleation dominated in martensite nucleation, which dividing untransformed austenite into several regions, and resulting in the larger size of fresh martensite. Martensite can not only nucleate at parent austenite grain boundaries, but also nucleate in the preformed martensite laths and twins. Smaller constraint in the martensite growth was achieved in a larger parent austenite grain size, leading to the longer fresh martensite and secondary martensite. Besides, the transformation kinetics of martensite was accelerated in a higher quenching temperature. Moreover, the martensitic laths presented in parallel laths (0~2°) based on the pre-formed lath or distributed in triangle, parallelogram or hexagon with an angle of 60° or 120°. Interestingly, martensitic lath also traversed the unstable new parent austenitic grain boundaries. In addition, the size of austenite grains increased with the quenching temperature, and austenite grains coarsened in a short time at a higher quenching temperature of 1160 ℃. Furthermore, a large amount fine dispersed particles redissolved and ripped at 1160 ℃, resulting in the many large and visible carbonitrides.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Abstract Background: Parkinson's disease (PD) is a neurodegenerative disorder featured with motor and non-motor deficits. Using 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine (MPTP) induced dopamine neuron degeneration has been widely used to produce reliable animal models of the PD. However, most of previous preclinical studies focused on the motor dysfunctions, few non-motor symptoms were evaluated. So far there is a lack of comprehensive investigation of the non-motor symptoms in animal models. Objectives: In this study, we aim to use a battery of behavioral methods to evaluate the non-motor symptoms in MPTP-induced non-human primate PD models. Methods: Cognitive functions, sleep and psychiatric behaviors were evaluated in MPTP-treated cynomolgus monkeys. The tests consisted of delayed matching-to-sample (DMTS), physical activity monitor (PAM), apathy feeding task (AFT), human intruder test (HIT), novel fruit test (NFT) and predator confrontation test (PCT). In addition, we tested whether the dopamine receptor agonist pramipexole (PPX) will improve these non-motor symptoms. Results: The present results show that the MPTP-treated monkeys exhibited cognitive deficits, abnormal sleep, and anxiety-like behaviors as compared to the control monkeys. These symptoms were relieved partially by PPX. Conclusions: These results suggest that MPTP-induced PD monkeys displayed non-motor symptoms that were similar to those found in PD patients. PPX treatment showed moderate therapeutic effects on these non-motor symptoms. This battery of behavioral tests may provide a valuable model for future preclinical research.

This study investigated the efficiency of scale-propellers, typically used on small drones. A scale-propeller is accepted as having a diameter of 7 to 21 inches. The Ukraine War has demonstrated the utility of relatively small, low-cost first-person view (FPV) drones, which are attritable. This investigation outlines the development of a MATLAB optimisation code, based on minimum induced loss propeller theory, which calculates the optimal chord and twist distribution for a chosen propeller operating in known flight conditions. The MATLAB code includes a minimum Reynolds number functionality, which provides the option to alter the chord distribution to ensure the entire propeller is operating above a set threshold value of Reynolds (&gt;100,000), as this has been found to be a transition point between low and high section lift-to-drag ratios. Additional functions allow plotting of torque and thrust distributions along the blade. The results have been validated on experimental data taken from an APC ‘Thin Electric’ 10” x 7” propeller, where it was found that both the chord and twist distributions were accurately modelled. The MATLAB code resulted in a 16% increase in the maximum propulsive efficiency. Further work will investigate a direct interface to SolidWorks to aid rapid propeller manufacturing capability.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

Autophagy is an evolutionarily conserved mechanism for degrading and recycling different cellular components in both normal development and stress conditions. Our recent research demonstrated that autophagy-mediated compartmental cytoplasmic deletion is essential for pollen germination. However, how autophagy regulates pollen germination to ensure its fertility remains largely unknown. Here, we applied multi-omic analyses to investigate the downstream pathways of autophagy in the process of pollen germination. Although ATG2 and ATG5 play similar roles in regulating pollen germination, high-throughput transcriptomic analysis reveals that silencing ATG5 has greater impact on the transcriptome than silencing ATG2. Cross-comparisons of transcriptome and proteome analysis reveal that gene expression at mRNA level and protein level are differentially affected by autophagy. Furthermore, high-throughput metabolomics analysis demonstrates that pathways related amino acid metabolism and aminoacyl-tRNA biosynthesis can be affected by both ATG2 and ATG5 silencing. Collectively, our multi-omic analyses reveal a central role of autophagy in cellular metabolism, which is critical for the initiation of pollen germination and the guarantee of pollen fertility.

Panax ginseng C. A. Meyer (P. ginseng), has been widely used in traditional Chinese medicine (TCM). It contains a number of chemical components and possesses a variety of pharmacological activities. Alzheimer's disease (AD) is neurodegenerative disease that creates a huge burden on the lives and health of individuals. In recent years, studies have indicated that the chemical components of P. ginseng, especially ginsenosides, play a pronounced positive role in the prevention and treatment of neurological diseases. This review aimed to summarize currently studies on chemical components and the mechanisms action in AD intervention treatment of P. ginseng, especially ginsenosides. In this review, the components of P. ginseng and their respective active effects were first introduced. Then the key molecular mechanisms and signaling pathways of P. ginseng were introduced, and its different active ingredients in the prevention and treatment of Alzheimer's disease-related pathogenesis were also summarized from the pathogenesis of AD Aβ generation and aggregation, hyperphosphorylation of tau protein，oxidant stress，neuroinflammation，mitochondrial damage，disorder of neurotransmitter and gut microbiota. Signaling pathway networks related to the action of ginseng active ingredients was constructed, which could serve as a therapeutic target for Alzheimer's disease. In addition to a detailed report on P. ginseng in improving Alzheimer's disease-related pathogenesis, the application of the current technology, spatial metabonomics in AD therapeutics and diagnostics were later discussed. Spatial metabonomics could be applied to investigate the multi-target intervention of P. ginseng on Alzheimer's disease. Research perspectives for the study of P. ginseng in the treatment of Alzheimer's disease were provided for further studies.

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

With the increase of global human activities, a large number of technogenic magnetic particles (TMPs) generated by industrial activities such as coal combustion, traffic and so on enter sediments on continental shelves. However, there is currently a lack of understanding of the spatiotemporal distribution of TMPs on continental shelves, as well as the sedimentary effects they cause. This review work comprehensively analyzes the source, morphology, composition, and spatiotemporal distribution characteristics of TMPs. Then it elucidates their magnetic contribution to sedimentary environments in continental shelf seas, as well as the influence of heavy metals and active iron. At the same time, the existing problems and future development directions of TMPs on continental shelves are summarized.

The porous structure is an important three-dimensional morphological feature of the peripheral nerve guidance conduit (NGC), which permits infiltration of cells, nutrients, and molecular signals, and the discharge of metabolic waste. Porous structures with precisely customised pore sizes, porosities, and connectivities were used to construct fully permeable, semi-permeable, and asymmetric peripheral NGCs to replace traditional nerve autografts in treatment of long-segment peripheral nerve injury. In this review, the features of porous structures and classification of NGCs based on these characteristics are discussed. Common methods for constructing 3D porous NGCs in current research are described, as well as the pore characteristics and the parameters used to tune the pores. The effects of the porous structure on the physical properties of NGCs including biodegradation, mechanical performance, and permeability were analysed. Pore structure affects the biological behaviour of Schwann cells, macrophages, fibroblasts, and vascular endothelial cells during peripheral nerve regeneration. Construction of ideal porous structures is a significant advancement in the regeneration of peripheral nerve tissue engineering materials. The purpose of this review is to generalise, summarise, and analyse the preparation methods for porous NGCs and their biological functions in promoting peripheral nerve regeneration to guide development of medical nerve repair materials.

Retinal vein cannulation involves puncturing an occluded vessel on the micron scale. Even single millinewton force can cause permanent damage. An ophthalmic robot with a piezo-driven injector is precious enough to perform this delicate procedure, but the uncertain viscoelastic characteristics of the vessel makes it difficult to achieve the desired contact force without harming the retina. The paper utilizes a viscoelastic contact model to explain the mechanical characteristics of retinal blood vessels in order to tackle this issue. The uncertainty in the viscoelastic properties is considered an internal disturbance of the contact model, and an active disturbance rejection controller is then proposed to precisely control the contact force. The experimental results show that this method can precisely adjust the contact force at the millinewton level even when the viscoelastic parameters vary significantly (up to 403.8%). The root mean square (RMS) and maximum value of steady-state error are 0.32 mN and 0.41 mN. The response time below 2.51 s with no obvious overshoot.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

Using the Super-SBM method, this study calculates the carbon emission efficiency (CEE) of 30 provinces in mainland China from 2011 to 2019. Then, using the systematic GMM model, spatial Durbin model, and mediating effect model, it examines the direct effect, spatial effect, and influence mechanism of the digital economy (DE) on CEE. It was found that (1) the DE significantly promoted regional CEE, but had a negative effect on CEE in provinces with high economic correlation; (2) mechanism studies showed that the DE improved CEE by reducing energy intensity, promoting industrial upgrading and green technology innovation; (3) regional heterogeneity analysis found that the DE significantly improved CEE in eastern provinces, but not in central and western provinces. DE improves CEE in provinces with high level of economic development, but decreases CEE in provinces with low level of economic development.This paper provides some empirical and theoretical references for the development of DE to improve CEE.

Bipolar disorder is a severe mood disorder and is one of the top 20 reasons of disability in the world. It causes a huge burden on society. In this study, the prediction models of bipolar disorder were constructed based on the concept of knowledge distillation. The input data consisted of patients of bipolar disorder and matched controls, all of which were selected from the open database MIMIC. The method of kernel density estimation (KDE) was exploited to generate probability density functions (PDF) which identify distributions of input data. The PDF values referred to as the soft labels were combined with the input data to construct the prediction models of bipolar disorder using decision tree and artificial neural network respectively. According to the evaluation results, indicators for identifying positive samples of bipolar disorder were improved. Meanwhile, the indicators for identifying negative samples have also been advanced. In addition, the branching attributes selected by the decision trees can be mapped back to specific disease diagnoses, which are all associated with bipolar disorder. In conclusion, using KDE to generate the soft label information of the input data can make knowledge distillation work and has improved the performances of prediction models for bipolar disorder.

We present a method to study the interannual variability of the annual cycle. The method consists of first determining the amplitude and phase of segments of 12 monthly means at all spatial points, resulting in one complex number per grid point and per year. The complex fields, once per year, are then subject to a complex EOF (CEOF) analysis. We consider as an example the barotropic stream function in the South China Sea as simulated with an ocean general circulation model across 6 decades of years, driven my realistic (NCEP) weather forcing. We find 3 to 4 to “significant” CEOFs, which account for about 53 to 62% of variance. These CEOFs go with large-scale patterns. Their time coefficients are mostly stationary, but point to some inhomogeneities related to instationarities in the forcing. In particular, the simulation since 1950-1958 deviates from the remainder of the simulation. The first CEOF describes variations in the center of the South China Sea. Its principal component describes a systematic, albeit noisy shift by almost 180o from 1960 to about the year 2000. When overlaid the long-term mean annual mean, the overall change consists of an amplification of the annual cycle in the 1960s and 1990s, whereas In the 1970s, the amplitude was reduced. Phase shifts in the anomaly (given by the CEOFs) have a small effect, because of the dominance of the mean annual cycle. These variations are not related to ENSO variability but may origin in variations of the Southeast monsoon. The second EOF represents strong changes, both in terms of intensity and phase, in the Luzon strait.

Taiwan’s Chi Mei Medical Center has a vision of becoming a sustainable organization. They found they violated the sustainable development goal (SDG) 13 (“Climate Action”) since its workflows consume excessive tangible resources and waste much operation time. To fulfill the vision, the Chi Mei Medical Center first introduced electronic invoicing. Implementing this electronic invoicing included adopting cloud E-invoice data and creating a software robot for auditing them. This study presents this software robot and its contributions. The software robot replaces an internal auditor to log into Taiwan’s E-invoice platform, download cloud E-invoice data, and detect the inconsistency between these cloud and on-premise data. Internal auditors of the Chi Mei Medical Center only needed to confirm the detection results. They welcome this software robot since it significantly reduces their work burdens. They approved more software robots for assisting other workflows. Besides, the Chi Mei Medical Center earned profits after eliminating paper invoices. This elimination helped release less carbon. This study concludes that chasing a sustainable organization is unnecessarily equivalent to the requirement of more costs. A software robot represents the last puzzle for constructing a paperless workflow since it can resolve the resistance of existing workers to a new workflow.

Streets are an essential element of urban safety governance and urban design, but they are designed with little regard for possible gender differences. This study proposes a safety perception evaluation method from the female perspective based on street view images (SVIs) and mobile phone data, taking the central city of Guangzhou as an example. The method relies on crowdsourced data and uses a machine learning model to predict the safety perception map. It combines the simulation of women's walking commuting paths to analyse the areas that need to be prioritised for improvement. Multiple linear regression was used to explain the relationship between safety perception and visual elements. The results showed the following: 1) There were differences in safety perceptions across genders. Women gave overall lower safety scores and more dispersed distribution of scores. 2) Approximately 11% of the streets in the study area showed weak perceived safety, and approximately 3% of these streets have high pedestrian flows and require priority improvements. 3) Safe visual elements in SVIs included the existence of roads, sidewalks, cars, railways, people, skyscrapers, and trees. Our findings can help urban designers determine how to evaluate urban safety and where to optimise key areas. Both have practical implications for urban planners seeking to create urban environments that promote greater safety.

Drought and water scarcity are significant factors limiting the development of China's maize industry. Deep sowing, as a method to mitigate drought and preserve soil moisture and seedlings, can effectively mitigate the adverse effects of drought stress on their growth. However, deep sowing can influence the emergence of maize seedlings and has a certain impact on their growth and development. To investigate the physiological and transcriptomic changes in maize inbred lines under deep sowing stress, and the alleviation effects of exogenous hormones, this study investigated the response of mesocotyl in deep-seeding tolerant maize inbred line Qi319 and deep-seeding sensitive maize inbred line Zi330 to deep-seeding stress under exogenous MeJA treatment. The physiological and transcriptomic mechanisms underlying the alleviation of deep-seeding stress by exogenous MeJA were elucidated. Results showed that compared to normal sowing depth, mesocotyl length (MES), mesocotyl and coleoptile length (MESCOL) significantly increased under deep-seeding stress for both inbred lines, while seedling length (SDL) was significantly inhibited. However, after adding 1.5 μmol·L^-1 MeJA, MES, MESCOL, and SDL significantly increased compared to deep-seeding stress alone. Exogenous MeJA promoted cell elongation, enhanced mesocotyl length, and improved seedling emergence ability. RNA-Seq sequencing revealed differentially expressed genes (DEGs). Under deep-seeding stress compared to normal sowing depth conditions, 1248 DEGs were identified in Qi319 and 1288 DEGs were identified in Zi330. After adding exogenous MeJA under deep-seeding stress compared to normal sowing depth with exogenous MeJA treatment conditions, 538 DEGs were identified in Qi319 and 2284 DEGs were identified in Zi 330. GO enrichment analysis showed that differentially expressed genes were mainly concentrated in biological processes, cell components and molecular functions. KEGG enrichment analysis showed that differentially expressed genes were mainly concentrated in transport and catabolism, signal transduction, amino acid metabolism and lipid metabolism processes. Compared with the deep-seeded treatment, 12 differentially expressed genes were co-expressed in the two inbred lines under exogenous MeJA treatment, and 10 key genes, including ornithine decarboxylase, terpene synthase 7 and ethylene reaction transcription factor 11, were screened out. Our findings elucidate the molecular mechanism underlying maize's tolerance response to deep seeding and offer valuable insights into candidate gene resources for improving deep seeding tolerance in maize.

Alzheimer’s disease and related dementias (ADRD) remain a public health challenge in developing counties. We developed a needs-based essential care service package (ECSP) for care planning of persons living with dementia (PLWD) using a cross-sectional survey among PLWD in institutions in six cities in China (n= 1,299). Face-to-face interviews were conducted with caregivers of PLWD by trained staff between 2018 and 2019. Care service needs and utilization by the level of cognitive impairment were summarized. The average age of PLWD was 80.7 years. 76% of participants had severe cognitive impairment. The needs-based ECSP with 30 service items would be sufficient in supporting care services of PLWD in China, of which seven items are core care. The selection plan for ECSP at different levels is designed as “General Care Services + Selective Care Services”, in which service items for low-, mid-and high-level care for PLWD are 7+3, 7+6, and 7+10, respectively. The findings provide the first large-scale data on service needs and utilization of PLWD in mainland China. The ECSP for PLWD advanced in the paper was a practicable and effective quantitative management means. It is deserved to application in a large scale.

Water splitting technology is an efficient approach to generate hydrogen (H2) energy, which can well address the problems of environmental deterioration and energy shortage, as well as establishment of a clean and sustainable hydrogen economy powered by renewable energy sources due to the green reaction of H2 with O2. While the efficiency of H2 production by water splitting technology is intimately related with the reactions on electrode. Nowadays, the efficient electrocatalysts in water splitting reactions are the precious metal-based materials, i.e., Pt/C, RuO2 and IrO2. Ni (Co, Fe)-based layered double hydroxides (LDH) 2D materials are the typical non-precious metal-based materials in water splitting with advantages of low cost, excellent electrocatalytic performance and simple preparation methods, which exhibits a great potential for the substitution for precious metal-based materials. This review summarizes the recent progress of Ni (Co, Fe)-based LDH 2D materials for water splitting, which mainly focuses on discussing and analyzing the different strategies to modify LDH materials towards high electrocatalytic performance. We also discuss the recent achievements including their electronic structure, electrocatalytic performance, catalytic center, preparation process and catalytic mechanism. Furthermore, the characterization progress in revealing electronic structure and catalytic mechanism of LDH is highlighted in this review. Finally, we put forward some future perspectives related to design and explore advanced LDH catalysts in water splitting.

Identifying locations of landslide slip surfaces provides critical information for understanding the volume of landslides and the scale of disasters, which is essential for formulating disaster preparedness and mitigation strategies. Based on hydrogeological survey data from 24 deep-seated landslide-prone sites in Taiwan's mountainous regions, this study first developed the hydraulic conductivity potential index (HCPI) using principal component analysis to quantify hydraulic properties of disturbed rock formation with six geological factors. Then, The regression analysis was performed to construct a permeability estimation model for the geological environment of landslides. Finally, the established model was utilized to develop an identification method for potential slip depths in landslide-prone sites. Results indicated a strong relation between HCPI and hydraulic conductivity with a determination coefficient of 0.895. The relation equation confirmed that its generated data concerning the depths of significant changes in hydraulic conductivity could be used to identify potential slip surfaces. Additionally, this study successfully establishes a rule for identifying potential slip zones by summarizing data concerning the generated hydraulic conductivity profiles, stratigraphic lithology, existing inclinometer slip depth records, and groundwater level of landslide sites. This identification method was then applied to predict potential slip depths for ten landslide sites where slip surfaces have not yet occurred. These findings offer a new alternative to having early information on potential sliding depths for timely disaster management and control implementation.

Background Hokkaido is the northernmost, least populous, and coldest of the Japanese islands. It was the first prefecture to be affected by COVID-19, while Kanagawa is home to one of the most populous areas of Japan, namely the Tokyo metro area. The Japanese government responded early during the pandemic by identifying infected patients, contact tracing, and performing PCR analysis on anyone who was suspected of having been exposed to SARS-CoV-2. The government has also been publishing information about each individual who tested positive for the virus. Both Hokkaido and Kanagawa started recording COVID-19 cases in the winter of 2020 and have detailed records of thousands of patients, thus providing an invaluable resource for the transmission and behavior of the virus. Methods The current study analyzed the COVID-19 registry data from the Hokkaido and Kanagawa prefectures. The Hokkaido registry contained 1,269 cases (674 (53%) females and 595 (47%) males) recorded between February 14 and July 22, 2020. The Kanagawa registry had 3,123 cases (1,346 (43%) females and 1,777 (57%) males. The final data contained a total of 4,392 cases (2,020 (46%) females and 2,372 (54%) males). By leveraging the information on viral transmission paths available in the registry data, we performed exponential random graph model (ERGM) network analysis to examine demographic and symptomological homophilies of the SARS-CoV-2 viral transmission networks. Results We observed age, symptomatic, and asymptomatic homophilies in both prefectures. Furthermore, those patients who contracted the virus through secondary or tertiary contacts were more likely to be asymptomatic than those who contracted it from primary infection cases. The transmission networks showed that transmission occurred significantly in healthcare settings, as well as in families, although the size of the networks was small in the latter. Most of the transmissions stopped at the primary and secondary levels and no transmission beyond quaternary was observed. We also observed a higher level of asymptomatic transmission in Kanagawa than in Hokkaido. Conclusions Symptom homophilies are an important component of COVID-19 and suggest that nuanced genetic differences in the virus may affect its epithelial cell type range and can thus result in the diversity of symptoms seen in individuals infected by SARS-CoV-2. Moreover, environmental variables such as temperature and humidity may also be playing an important role in the overall pathogenesis of the virus.

Abstract: Based on the survey data of 5 large grain-producing provinces in China, this paper studies the effect of agricultural production trusteeship on agricultural carbon emission reduction by using a propensity score matching method. The empirical results show that the carbon emission of wheat reduces by 7.107kg/mu, with a decrease rate of 15.5% after participating in agricultural production trusteeship. Among them, chemical fertilizers, manpower input, agricultural chemicals and diesel oil respectively reduces with rates of 14.2%, 27.7%, 14.1%, and 6%. However, there are differences in the facilitation effects of different trusteeship services, with the best promotion effect of field management services, followed by cultivation, planting and harvest services, and then agricultural material supply services, the ATT is -6.160, -5.732 and -5.530, respectively. Meanwhile, there are differences in the promotion effects for farm households with different factor endowments. The promotion effect is better for small farm households with 1 type of agricultural machinery or less, and an operation scale of 7 mus or less. Therefore, in order to better play the role of agricultural production trusteeship on agricultural carbon emission reduction, the government should vigorously support its development and guide more smallholders to choose agricultural production trusteeship.

We studied surface enhanced Raman spectra of amino acids D-alanine and DL-serine and their mixture on silver nanoisland films (SNF), immersed in phosphate buffer saline solution at millimolar amino acid concentrations. It is shown that the spectra from the amino acid solutions differ from the reference spectra for microcrystallites due to electrostatic orientation of amino acid zwitterions by the metal nanoisland film. Moreover, non-additive peaks are observed in the spectrum of the mixture of amino acids adsorbed on SNF, which means that intermolecular interactions between adsorbed amino acids are very significant. The results indicate the need for a thorough analysis of the Raman spectra from amino acid solutions in the presence of a nanostructured metal surface, and may also be of interest for studying molecular properties and intermolecular interactions.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

Artificial Intelligence (AI) is poised to revolutionize the architectural design and energy management of green buildings, offering significant advancements in sustainability and efficiency. This paper explores the transformative impact of AI on improving energy efficiency and reducing carbon emissions in commercial buildings. By leveraging AI algorithms, architects can optimize building performance through advanced environmental analysis, automation of repetitive tasks, and real-time data-driven decision-making. AI facilitates precise energy consumption forecasting and integration of renewable energy sources, enhancing the overall sustainability of buildings. Our study demonstrates that AI can reduce energy consumption and CO2 emissions by approximately 8% and 19%, respectively, in typical mid-size office buildings by 2050 compared to conventional methods. Further, the combination of AI with energy efficiency policies and low-emission energy production is projected to yield reductions of up to 40% in energy consumption and 90% in CO2 emissions. This paper provides a systematic approach for quantifying AI's benefits across various building types and climate zones, offering valuable insights for decision-makers in the construction industry.

The construction industry is an important part of the national economic market of various countries; since 2013, the construction industry's added value in the gross domestic product has been more than 6%, reaching 6.89% in 2022, and is a pillar industry of the national economy. Intelligent construction is the realistic demand to promote the high-quality development of China's construction industry. It is the key focus of transforming and upgrading the traditional construction industry to information, digital, and intelligent. As a new production factor, construction robots have become the key to promoting intelligent construction. Under the guidance of various national and industry policies, thanks to China's huge construction market volume and rich application scenarios, many innovative and entrepreneurial entities have entered the field of construction robots. Architectural visualization is a crucial aspect of architectural design and communication. With the development of science and technology, artificial intelligence (AI) technology is increasingly becoming an essential tool for architectural visualization and communication. The emergence of AI technology has provided architects with more flexible and creative ways to present design ideas. All along, designers who love architecture have been passionate about exploring better solutions for architecture, but there is never an optimal solution for architectural design; AI is the fire of the future era; it brings us more opportunities but also forces us to face new challenges from the future.

It is very difficult to accurately divide farmland and woodland in Gaofen 2 (GF-2) remote sensing image, because their single plant coverage is very small, and their spectra are very similar. The ratio of spatial resolution and one plant’s coverage area must be fully taken into account when designing the Convolutional Neural Network structure for extracting them from GF-2 image. We establish a Convolutional Encode Neural Networks model (CENN), The first layer has two sets of convolution kernels to learn the characteristics of farmland and woodland respectively, while the second layer is the encoder to encode the characteristics by transfer function, which can map the results to the corresponding category number. In the training stage, samples of farmland, woodland, and other categories are categorically used to train CENN, as soon as training is accomplished, CENN would acquire enough ability to accurately extract farmland and woodland from remote sensing images. The final extraction result is obtained by implementing per-pixel segmentation of images used to train the CENN. CENN is compared and analyzed with others such as Deep Belief Network (DBN), Full Convolutional Network (FCN), Deeplab Model. The results of experiments show that CENN can more accurately mine the characteristics of farmland and woodland, and it achieves its goal of extracting farmland and woodland with high precision from GF-2 images.

With the development of artificial intelligence, the ability of capturing the background characteristics of hyperspectral imagery (HSI) is improved and promising performance in hyperspectral anomaly detection (HAD) tasks is yielded. However, existing methods proposed in recent years still suffer from certain limitations: 1) constraints are lacking in the deep feature learning process in terms of the issue for absence of prior background and anomaly information. 2) hyperspectral anomaly detectors with traditional self-supervised deep learning methods fail to ensure prioritized reconstruction of the background. 3) architectures of fully connected deep network in hyperspectral anomaly detectors lead to low utilization of spatial information and destruction for original spatial relationship of hyperspectral imagery, and disregard spectral correlation between adjacent pixels. 4) hypotheses or assumptions for background and anomaly distributions restrict the performance of many hyperspectral anomaly detectors because the distributions of background land covers are usually complex and not assumable in real-world hyperspectral imagery. With the consideration of above problems, in this paper, we propose a novel fully convolutional auto-encoder based on dual clustering and latent feature adversarial consistency (FCAE-DCAC) for HAD which is carried out in a self-supervised learning-based processing. Firstly, the density-based spatial clustering of applications with noise algorithm and connected component analysis are utilized for successive spectral and spatial clustering to obtain more precise prior background and anomaly information, which facilitates the separation between background and anomaly samples during the training of our method. Subsequently, a novel fully convolutional auto-encoder (FCAE) integrated with spatial-spectral joint attention (SSJA) is proposed to enhance the utilization of spatial information and augment feature expression. In addition, a latent feature adversarial consistency network is proposed to achieve pure background reconstruction with the ability of learning actual background distribution in hyperspectral imagery. Finally, a triplet loss is introduced to enhance the separability between background and anomaly, and the reconstruction residual serves as the anomaly detection result. We evaluate the proposed method on seven groups of real-world hyperspectral datasets, and the experimental results confirmed the effectiveness and superior performance of the proposed method versus nine state-of-the-art methods.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

The shift towards autonomous excavators in construction and mining is a significant leap towards enhancing operational efficiency and ensuring worker safety. However, it presents challenges such as the need for sophisticated decision-making and environmental perception due to complex terrains and diverse conditions. Our study introduces the E-GTN framework, a novel approach tailored for autonomous excavation that leverages advanced multisensor fusion and a custom-designed convolutional neural network to address these challenges. Results demonstrate that GridNet effectively processes grid data, enabling the reinforcement learning algorithm to make informed decisions, thereby ensuring efficient and intelligent autonomous excavator performance. The study concludes that the E-GTN framework offers a robust solution for the challenges in unmanned excavator operations, providing a valuable platform for future advancements in the field.