Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

In 2011-2012, Northern Vietnam suffered its first large scale hand foot and mouth disease (HFMD) epidemic. Two sets of official guidelines were issued during the outbreak to handle the HFMD crisis. The city of Hai Phong was therefore used as a model to analyze the impact of the guidelines release. 9621 HFMD cases were reported in Hai Phong city from April 2011 to December 2012. Three distinct waves of HFMD occurred. Enterovirus A71 and Coxackievirus A16 were successively associated to the epidemics. Two periods, before and after guidelines realease, could be distinguished which were characterized by different patient patterns Time to admission and severity changed notably. Guideline publication help the health system refocusing on the 0.5-3 years age group with highest incidence of the disease. The three waves showed different special distribution but main routes of infection were rivers and local secondary roads most likely through local trade and occupational movements of people.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

Flood frequency analysis at large scales, essential for the development of flood risk maps, is hindered by the uncertainty in outputs of process-based hydrological models and the scarcity of gauge flow data. We develop a Bayesian hierarchical model (BHM) based on the Generalized Extreme Value (GEV) distribution for regional flood frequency analysis at high resolution across North America. Our model leverages annual maximum flow data from ≈20000 gauged stations and a dataset of 130 static catchment-specific covariates to predict extreme flows at all catchments over the continent as well as their associated statistical uncertainty. Additionally, a modification is made to the data layer of the BHM to include daily gauge discharge data when available, which improves the precision of the discharge level estimates. We validated the model using a hold-out approach and found that its predictive power is very good for the GEV distribution location and scale parameters and improveable for the shape parameter, which is notoriously hard to estimate. The resulting discharge return levels yield satisfying agreement when compared with available design peak discharge from various government sources. Assessment of the covariates’ contributions to the model also informs on the most relevant underlying factors influencing flood-inducing peak flows. The key covariates in our model are temperature-related bioindicators, the catchment drainage area and geographical location.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

An HFMD outbreak spread over the city of Hải Phòng from Summer 2011 to Autumn 2012. This epidemic was chosen because it was the very first HFMD epidemic in North Vietnam, eliminating thus interferences with previous outbreaks. This epidemic displayed 3 separate waves. A complete dataset was collected for more than 9500 patients during this period, which enabled us to analyze this epidemic at different scales. Access to the healthcare system was crucial during this period, with a reorganization of the system in February-March 2012. An analysis at commune level enables us to track the epidemic along certain communication routes. The three-waves structure reveals a wide disparity at district level. We develop a mathematical model showing high accuracy at the adjustment of data for both the total number of cases and for the number of cases per week. As a consequence, the model was able to accurately determine the dates of beginning and end of each wave and to show that they overlapped. Using mathematical functions associated with this model, it was possible to calculate the probability for a patient to belong to a specific wave.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

This paper presents a comprehensive cost-benefit analysis of producing alternative phosphorus (P) fertilizers from recycled water treatment residuals (Fe-WTR) and cowshed effluents, under the umbrella of circular economy approach. Fe-WTR is compared to a synthetic adsorbent, layered double hydroxide (LDH). Dairy wastewater is used as a P source for both adsorbents. The cost of 1 ton P-Fe-WTR sums up to 329 Euro. In contrast, the use of synthetic adsorbents (P-LDH) incurs significantly higher costs, amounting to 3329 Euros per ton, underscoring the economic advantage of utilizing waste-derived materials. Adopting Fe-WTR fertilizer not only offers substantial cost savings by avoiding landfill fees (40-150 Euros per ton) and wastewater discharge fines (500 Euros per ton) but also reduces environmental impacts. This sustainable method mitigates eutrophication and pollution, presenting a dual benefit of cost-effectiveness and environmental protection. Although our results are based on a specific case study, they reflect the potential value of extending the circular economic approach to P production worldwide: Recycling P from waste streams can be economically viable and environmentally preferable at large, aligning with global sustainability goals and demonstrating the practicality of circular economy principles in environmental management.

To avoid loss of information and incorrect ranking, this paper proposes a method for ranking generalized fuzzy numbers, which guarantees both horizontal and vertical values are important parameters affecting the final ranking score. In this method, the normalized height coefficient is introduced to evaluate the influence of the height of fuzzy numbers on the final ranking score. The higher the normalized height coefficient of a fuzzy number is, the higher its ranking. The left area and the right area are presented to calculate the impact of vertical value on the final ranking score. The left area is considered the benefit area. The right area is considered the cost area. The fuzzy number is preferred if the benefit area is larger and the cost area is smaller. The proposed method can be employed to rank both normal and non-normal fuzzy numbers without normalization or height minimization. Numerical examples and comparison with other methods highlight the feasibility and robustness of the proposed method, which can overcome the shortcomings of some existing methods and can support decision-makers to select the best alternative.

A highly crystallized monoclinic-scheelite type BiVO4 powders were successfully synthesized by solvothermal method. The as-synthesized BiVO4 powders were characterized by XRD, FE-SEM, Raman spectroscopy, UV-vis DRS spectroscopy and TA-PL. From the XRD data and Raman spectra, the monoclinic-scheelite phase BiVO4 sample can be obtained at higher solvothermal synthesis temperature more than 140 oC. The preparation conditions such as, the Bi/V molar ratio and synthesis temperature, have significantly effects on the morphologies of the BiVO4 samples. BVO2 sample shows the highest PL peak, which has the highest formation rate of OH radicals and the highest photocatalytic activity. This result suggests that the formation rate of OH radicals shows a good correlation with the photocatalytic activity.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Microcystis aeruginosa is a common cyanobacteria found in water blooms and often causes ecological harm. Antibiotics are also increasingly used for the prevention and treatment of bacterial infections in aquaculture. However, since most antibiotics cannot be fully metabolized, they enter the water environment and cause ecological impacts. In this paper, the effects of the two quinolone antibiotics (enrofloxacin and ciprofloxacin) on the population density and microcystins (MCs) production of Microcystis aeruginosa were studied. It is of great significance for the ecological risk assessment of antibiotics to the water environment. The results showed that the 96h EC50 values of enrofloxacin and ciprofloxacin to Microcystis aeruginosa were 56.10mg/L and 49.80mg/L respectively, and the toxicity of ciprofloxacin to Microcystis aeruginosa was slightly stronger than that of enrofloxacin. With the increase of the two quinolone antibiotic concentration, the growth inhibition rate (IR) increased, but when the concentration reached a certain height, the IR would reach its threshold. Long-term exposure to low concentrations of these two quinolone antibiotics is not only more likely to lead to the outbreak of Microcystis aeruginosa, but also increase its toxin production capacity. The highest contents of MCs in enrofloxacin and ciprofloxacin groups were 95.539 μg/g and 93.720 μg/g, respectively. The MCs value of these three enrofloxacin treatment groups was more than above 51.8 times that of control group (CK) on the 4th day; from 8th day to 14th day, the MCs value of these three enrofloxacin treatment groups was more than above 3.2 times that of CK group. For another ciprofloxacin, the MCs value of the treatment group was more than 64.98 times that of the CK group on the 4th day, and from 8th day to 14th day, the MCs value of the treatment group was more than 2.7 times that of the CK group. These findings provide crucial management rationale.

The fundamental objective is to study the application of multivariate sets of data in Gaussian distribution. This paper examines broad measurements of structure for both Gaussian and non-Gaussian distributions, which shows that they can be described in terms of the infor-mation-theoretic between the given covariance matrix and correlated random variables (in terms of relative entropy). In order to develop the multivariate Gaussian distribution with entropy and mutual information, several significant methodologies are presented through the discussion supported by illustrations, both technically and statistically. The content obtained allows readers to better perceive concepts, comprehend techniques, and properly execute software programs for future study on the topic's science and implementations. It also helps readers grasp the themes' fundamental concepts. Involving the relative entropy and mutual information as well as the potential correlated covariance analysis based on differential equations, a wide range of information is addressed, including basic to application concerns.

The proton exchange membrane fuel cell (PEMFC) is a critical and essential component of zero-emission electro-hydrogen generators. An accurate prediction of its performance is important for optimal operation management and preventive maintenance of these generators. However, the prediction is not simple because the PEMFCs have complex electrochemical reactions with multiple nonlinear relations between operating variables as inputs and voltage as output. In this paper, we propose an efficient prediction approach based on XGBRegressor and Tree-structured Parzen Estimator. In addition, to better select relevant features, Kernel Principal Component Analysis and Mutual Information are jointly used. The proposed approach allows consideration of the dynamic operating conditions of the PEMFC. To test and validate the robustness of the proposed approach, a real data-set of ten PEMFCs was considered. Furthermore, a comparison study with traditional machine learning models, such as artificial neural networks and support vector machine regression, was investigated. The obtained results confirm that our model outperforms the considered traditionel machine learning models.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

Accelerators play a critical role in fostering innovative ecosystems and nurturing startups. The evaluation and selection of startups, particularly technology-based startups, for acceleration programs are essential in accelerator economy and management. Assessment of startups requires consideration of numerical and qualitative criteria such as sales, prior startup experience, demand validation, and product maturity. Startups must be ranked based on the varying importance of criteria, which can be identified as a fuzzy multi-criteria decision-making (MCDM) problem. MCDM methods have proven effective in managing complex problems. However, the use of MCDM techniques in startup selection and evaluation of criteria interrelationships from the accelerator perspective is yet to be researched. This study proposes a hybrid DEMATEL-ANP-based fuzzy PROMETHEE II model to rank startups and examine the interrelationships between factors. The final preference values are fuzzy numbers, making a fuzzy ranking method necessary for decision-making. An extension of ranking fuzzy numbers using a spread area-based relative maximizing and minimizing set is suggested to improve the flexibility of existing ranking MCDM methods. Algorithms and formulas are derived and a comparison demonstrates the merits of the proposed method. Finally, a numerical experiment is designed to address the viability of the hybrid DEMATEL-ANP-based fuzzy PROMETHEE II model.

Europium (Eu)-doped fluorapatite (FA) nanorods has a similar biocompatibility with hydroxyapatite (HA) in terms, attracted much attention as cell imaging biomaterials due to their luminescent property. Here, we will discuss the new feature of europium doped fluorapatite (Eu-FA) nanorods as anticancer drug carrier. Eu-FA nanorods was prepared using a hydrothermal method. The morphology, crystal structure, fluorescence and composition are investigated. The specific crystal structure, enabling an effective loading of drug molecules. Doxorubicin (DOX), used as an anticancer model drug, was shown to be effectively loaded onto the surface of the nanorods. The DOX release was fairly pH-dependent, occurring more rapidly at pH 5.5 than pH 7.4 was observed. The intracellular penetration of the DOX-loaded Eu-FA nanorods (Eu-FA/DOX) can be imaged in situ due to the self-fluorescence property. Treatment of melanoma A375 cells with Eu-FA/DOX elicited a more effective apoptosis rate than direct DOX treatment. Overall, Eu-FA show great promise for tracking and treating tumor, may potentially useful as a multifunctional carrier system to effectively load and sustainably deliver drugs.

The selectin of a demand forecasting method is critical for companies aiming to avoid manufacturing overproduction or shortages in pursuit of sustainable development. Various qualitative and quantitative criteria with different weights must be considered during the evaluation of a forecasting method. The qualitative criteria and criteria weights are usually assessed in linguistic terms. Aggregating these various criteria and linguistic weights for evaluating and selecting demand forecasting methods in sustainable manufacturing is a major challenge. This paper proposes an extension of fuzzy Elimination and Choice Translating Reality (ELECTRE) I to resolve this problem. In the proposed method, fuzzy weighted ratings are defuzzified with the signed distance to develop a crisp ELECTRE I model. Moreover, an extension to ELECTRE I is developed by suggesting an extended modified discordance matrix and a closeness coefficient for ranking alternatives. The proposed extension can overcome the problem of information loss which can lead to incorrect ranking result when using the Hadamard product to combine concordance and modified discordance matrices. A comparison is conducted to show the advantage of the proposed extension. Finally, a numerical example is used to demonstrate the feasibility of the proposed method; furthermore, a numerical comparison is made to display the advantage of the proposed method.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

An emerging picture in cancer biology is that, paradoxically, chemotherapy can actively induce changes that favor cancer progression. These pro-cancer changes can be either inside (intrinsic) or outside (extrinsic) the cancer cells. In this review, we will discuss the extrinsic pro-cancer effect of chemotherapy; that is, the effect of chemotherapy on the non-cancer host cells to promote cancer progression. We will focus on metastasis, and will first discuss recent data from mouse models of breast cancer. Intriguingly, despite reducing the size of primary tumors, chemotherapy changes the tumor microenvironment, resulting in an increased escape of cancer cells into the blood stream. Furthermore, chemotherapry changes the tissue microenvironment at the distant sites, making it more hospitable to cancer cells upon their arrival. We will then discuss the idea and evidence that these devastating pro-metastatic effects of chemotherapy can be explained in the context of stress response. At the end, we will discuss the potential relevance of these mouse data to human breast cancer and their implication on chemotherapy in the clinic.

Obsessive-Compulsive Disorder (OCD) is a mental health condition marked by recurrent intrusive thoughts or sensations that compel individuals to perform repetitive behaviors or mental acts. Obsessions and compulsions significantly disrupt daily life and cause considerable distress. Early identification and intervention improve long-term outcomes. This study aimed to evaluate the ability of four advanced artificial intelligence models (ChatGPT-3.5, ChatGPT-4, Claude, and Bard) to accurately recognize OCD compared to human professionals and to assess recommended therapies and stigma attributions. This study was conducted during March 2024 utilizing 12 vi-gnettes. Each vignette depicted a client, either a young adult or a middle-aged male or female, attending an initial therapy session. Each vignette was evaluated ten times, resulting in 480 evaluations. The results were compared with those of a human sample of 514 psychotherapists, as reported by Canavan. Significant differences were found. AI models demonstrated higher OCD recognition rates and confidence levels than human professionals and showed 100% confidence in recognition, compared to 87% among psychotherapists. AI models also recommended evi-dence-based interventions more frequently, with ChatGPT-3.5 and Claude at 100%, ChatGPT-4 at 90%, and Bard at 60%, compared to 61.9% among psychotherapists. Additionally, AI models ex-hibited significantly lower stigma and danger estimations, though both AI and psychotherapists demonstrated high willingness to treat the described cases. The findings suggest that AI models surpass human professionals in recognizing OCD and recommending evidence-based treatments while also demonstrating lower stigma. These results highlight the potential of AI tools to enhance OCD diagnosis and treatment in clinical settings.

Motivation: there is a paradox at the heart of informatics where practical implementation generally fails to understand the socio-technical impact of novel technologies and disruptive innovation when adopted in `real-world’ systems. This phenomenon, termed technological determinism, is manifested in a time-lag between the adoption of novel technologies and an understanding of the underlying theory which develops following research into their adoption. Methods: we consider informatics theory as it relates to: social informatics and how humans’ function in society, the relationship between society and technology, information systems, information systems design, and human-computer interactions. The challenges posed by novel technologies and disruptive innovation are considered as they relate to information systems and information systems design. Open research questions with directions for future research are discussed with an introduction to and our proposed approach to socio-technical information system design. Significance: we conclude that the adoption of disruptive innovation presents both opportunities and threats for all stakeholders in computerised systems. However, determinism is a topic requiring research to generate a suitable level of understanding and technological determinism remains a significant challenge.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

BackgroundIntracranial hemorrhage (ICH) in pregnancy, estimated at 1 in 10,000 cases, presents significant diagnostic challenges prenatally despite advanced imaging techniques such as ultrasound (US) and MRI. Detecting ICH is crucial for pregnancy management and future treatment decisions aimed at improving fetal survival and reducing brain damage. This report presents the diagnosis and outcomes of two cases of prenatal ICH.Cases presentationThe first case involves a 30-year-old pregnant woman with irregular prenatal care diagnosed with ICH at 32 weeks of gestation via US and MRI. She chose to continue the pregnancy, delivering a 3160g male infant at 36 weeks via cesarean section. Following NICU care including resuscitation and ventriculoperitoneal shunt placement, the infant was discharged. Subsequent examinations showed a reduction in ventricle size. In the second case, a 27-year-old woman taking acenocoumarol for a mechanical heart valve developed fetal subdural hemorrhage detected by US and MRI. She opted to terminate the pregnancy, resulting in a stillborn male infant weighing 1530g.ConclusionFetal ICH presents with varying severity and prognostic implications, diagnosed and graded using US. Fetal cranial MRI may help clarify the etiology. Management remains controversial, with termination of pregnancy potentially warranted in severe cases due to poor prognosis. Further research is needed to refine management and improve outcomes in fetal ICH.

In this paper, we propose a method to find all efficient solutions of an interval multiple objective linear programming (IMOLP) problem with interval coefficients in the objective functions, the constraint matrix and the right-hand side vector. The set of all efficient solutions of an IMOLP problem can completely supply information to the decision makers in finding their most preferred solutions but, up to now, not all efficient solutions of an IMOLP problem can be found by known methods. A numerical example is given to illustrate the working of the proposed method.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

Visual-inertial integrated navigation system (VINS) has been extensively studied over the past decades to provide accurate and low-cost positioning solutions for autonomous systems. Satisfactory performance can be obtained in an ideal scenario with sufficient and static environment features. However, there are usually numerous dynamic objects in deep urban areas, and these moving objects can severely distort the feature tracking process which is fatal to the feature-based VINS. The well-known method mitigates the effects of dynamic objects is to detect the vehicles using deep neural networks and remove the features belongs to the surrounding vehicle. However, excessive exclusion of features can severely distort the geometry of feature distribution, leading to limited visual measurements. Instead of directly eliminating the features from dynamic objects, this paper proposes to adopt the visual measurement model based on the quality of feature tracking to improve the performance of VINS. Firstly, a self-tuning covariance estimation approach is proposed to model the uncertainty of each feature measurements by integrating two parts: 1) the geometry of feature distribution (GFD), 2) the quality of feature tracking. Secondly, an adaptive M-estimator is proposed to correct the measurement residual model to further mitigate the impacts of outlier measurements, such as the dynamic features. Different from the conventional M-estimator, the proposed method effectively alleviates the reliance of excessive parameterization of M-estimator. Experiments are conducted in a typical urban area of Hong Kong with numerous dynamic objects, and the results show that the proposed method could effectively mitigate the effects of dynamic objects and improved accuracy of VINS is obtained when compared with the conventional method.

In this article, we introduce some multi-messenger studies of blazars. Main contents contain the following parts, 1. the subclasses of blazars and the observational characteristics, 2. emission variabilities from the multi-messenger observations, 3. the physical origin for the multi-messenger studies. Based on mid-IR observations collected from the $WISE$ database, we collect two sources (BZQ J1700+6830 and BZQ J1842+6809) to analyze the mid-IR variabilities. \\ (1) For BZQ J1700+6830, the period is $P\approx$ 42 hr at the four bands ($W1$, $W2$, $W3$, $W4$); for BZQ J1842+6809, the period is $P\approx$ 123 hr at the two bands ($W1$, $W2$). \\ (2) Using the periodicities, we calculate that the central black hole mass ($BH$) should be $M = (5.44\sim33.0)\times10^8M_{\odot}$ for BZQ J1700+6830 and $M = (1.13\sim6.88)\times10^9M_{\odot}$ for BZQ J1842+6809.\\ (3) For the two sources, during the flaring stage, we find anti-clockwise variation trends based on the time-based relations built by the spectral indices ($\alpha$) and flux densities ($F$).\\ (4) We calculate the Doppler factor ($\delta$) when the sources are in the dimming or brightening stages, and find that with the frequency increasing, the Doppler factor become stronger.

Initial periods of adsorption kinetics play an important role in estimating the initial adsorption rate and rate constant of adsorption process. Several adsorption processes rapidly occur, and the experimental data of adsorption kinetics under the initial periods can contain potential errors. The pseudo-second-order (PSO) kinetic model has been popularly applied in the field of adsorption. The use of the nonlinear optimization method to obtain the parameters of the PSO model can minimize error functions during modelling compared to the linear method. However, the nonlinear method has limitations in that it cannot directly recognize potential errors in the experimental points of time-dependent adsorption, especially under the initial periods. In this study, for the first time, the different linear types (Types 1–6) of the PSO model are applied to discover the error points under the initial periods. The result indicated that the fitting method using its linear equations (Types 2–5) is really helpful for identifying the error (doubtful) experimental points from the initial periods of adsorption kinetics. The imprecise points lead to low adjusted R2 (adj-R2), high reduced χ2 (red-χ2), and high Bayesian information criterion (BIC) values. After removing those points, the experimental data were adequately fitted with the PSO model. statistical analyses demonstrated that the nonlinear method must be used for modelling the PSO model because its red-χ2 and BIC were lower than the linear method. Type 1 has been extensively applied in the literature because of its very high adj-R2 (0.9999) and its excellent fitting to experimental points. However, its application should be limited because the potential errors from experimental points were not identified by this type. For comparison, the other kinetic models (i.e., pseudo-first-order, pseudo-nth-order, Avrami, and Elovich) are applied. The modelling result using the nonlinear forms of those models indicated that the fault experimental points from the initial periods were not detected.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

As e-commerce services and Internet technology have rapidly developed in recent years, many services and applications integrating these technologies can now be completed online. These commercial activities include online auctions, online ticketing and online payments. The client shops from the store online, andthe store delivers the goods to the client. The goods can be divided into digital products without entities, as well as actual entities. If it is a physical product, the store will deliver the package to the client through itslogistics. However, there have been many cases of switched goods purchased by clients in recent years. Earlier, some scholars proposed a security mechanism with a subliminal channel for E-cash and digital content. Only the sender and the receiver would know that the secret information was hidden in the signature. So the privacy of this subliminal message couldbe ensured. We apply this concept to the logistics environment to design secure logistics architecture with subliminal messages. The client can check the subliminal message of the received package, and know whether the package has been switched by malicious people. In addition, the proposed scheme also applies sensor technology;the client can check the GPS location, the temperature and humidity at any time during the delivery process. So intelligent logisticswouldthereby be achieved. This paper proposes an intelligent and secure package sensoring logistics system based on a subliminal channel. The proposed architecture uses the related mechanisms tosolve the problems of a logistics system, including how to achieve mutual authentication, data integrity, anti-switch package, package location and status tracing, resisting replay attacks, forward and backward secrecy, and non-repudiation issues.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

A new optical steganography scheme is proposed that transmits a stealth optical code-division multiple-access (OCDMA) signal through a public binary phase-shift keying (BPSK) channel. Polarization beam splitters and arrayed waveguide gratings are used to implement a spectral-polarization coding (SPC) system with an incoherent optical source. We employ a Walsh–Hadamard code as the signature code of the user who wants to transmit stealth information using the system. A free space optical link applied to this system maintains the polarization states of light during propagation. The secret data is extracted using correlation detection and balanced subtraction in the OCDMA decoder of the intended receiver, and the other signal from the public channel is reduced by the OCDMA decoder. At the demodulator of the public channel, BPSK demodulation eliminates the stealth signal so that the public channel is not affected by the stealth signal. The two signals cannot interfere with each other. The results of this study show that our proposed optical steganography system is highly secure. The stealth signal can be favorably hidden in the public channel when the average source power of the stealth signal, public noise, and public signal are −5, −3, and 0 dBm, respectively.

3D-mapping-aided (3DMA) global navigation satellite system (GNSS) positioning that improves positioning performance in dense urban areas has been under development in the recent years, but it still faces many challenges. This paper details a new algorithm that explores the potential of using building boundary for positioning. Rather than applying complex simulations to analyze and correct signal reflections by buildings, the approach utilizes a convolutional neural network to differentiate between the sky and building in a sky-pointing fisheye image. A new skymask matching algorithm is then proposed to match the segmented fisheye images with skymasks generated from a 3D building model. Each matched skymask holds a latitude and longitude coordinate to determine the precise location of the fisheye image. The results are then compared with the conventional GNSS and advanced 3DMA GNSS positioning methods. The aims of the proposed algorithm are to increase positioning and heading accuracy in a rich urban environment.

ZrO2-YO1.5-TaO2.5(ZYTO) composite ceramic is considered to be the candidate of next generation of thermal barrier coatings as its excellent thermal stability and low thermal conductivity in high temperature, however, the mechanical properties and fracture tougheness of ZYTO system may be the shortcomings compared with the 8YSZ. In this study, ZYTO composite ceramics were successfully prepared by chemical coprecipitation reaction, the microsture of resulting composites were studied as a function of doping of M-YTaO4. Mechanical properties, including the density, porosity, hardness and Young's modulus, are determinate; the toughening mechanism were verified by the crack growth behavior of Vickers indentation test Results suggested that M-YTaO4 refines the fluorite phase grain and strengthens the grain interface in the composite ceramic. The thermal mismatch between the second phase and matrix produces residual stress in the bulk and affects the crack propagation behavior. With the increase of M-YTaO4 doping, the grain coarsening and ferroelastic domains are observed in the experiments. The ferroelastic domains with orthogonal polarization directions near crack tip evidences the ferroelastic toughening mechanism. The competition among these crack behaviors, such as cracks deflection, bridging and bifurcation, dominates the actual fracture toughness of the composite. The best toughening formula is determinate in the two-phase region and the highest fracture toughness is about to 3.1MPa·m1/2. Above all, mechanical properties of ZYTO composite ceramics look potential for thermal barrier coatings materials.

Fibromyalgia (FM) is a complex, chronic, widespread pain syndrome that can cause significant health and economic burden. Emerging evidence has shown that neuroinflammation is an underlying pathological mechanism in fibromyalgia. Toll-like receptors (TLRs) are key mediators of the immune system. TLR4 is expressed primarily in microglia and regulates downstream signaling pathways, such as MyD88/NF-κB and TRIF/IRF3. It remains unknown whether electroacupuncture (EA) has therapeutic benefit in attenuating fibromyalgia pain and what role the TLR4 pathway may play in this effect. We compared EA with sham EA to eliminate the placebo effect due to acupuncture. We demonstrated that intermittent cold stress significantly induced an increase in mechanical and thermal FM pain in mice (mechanical: 2.48 ± 0.53 g; thermal: 5.64 ± 0.32 s). EA but not sham EA has analgesic effect on FM mice. TLR4 and inflammatory mediators-related molecules were increased in FM mice’s thalamus, medial prefrontal cortex, somatosensory cortex, and amygdala, indicating neuroinflammation and microglial activation. These molecules were reduced by EA but not sham EA. Furthermore, a new chemogenetics method was used to precisely inhibit SSC activity displayed an anti-nociceptive effect through TLR4 pathway. Our results imply that the analgesic effect of EA is associated with TLR4 downregulation. We provide novel evidence that EA can modulate the TLR4 signaling pathway, revealing potential therapeutic targets for FM pain.

The bimetallic (Ta/(Ti, V, Co, Nb) mesoporous MCM-41 nanoparticles were obtained by direct synthesis and hydrothermal treatment. The obtained mesoporous materials were characterized by XRD, XRF, N2 adsorption/desorption, SEM, TEM, XPS, Raman, UV-Vis, PL spectroscopy. A more significant effect was observed on mesoporous structure, typi-cally for MCM-41, and optic properties if the second metal (Ti, Co) does not belong to the same Vb group with Ta as V, Nb. The obtained new nanoparticles were used as catalysts for oxidation with H2O2 of olefinic compounds (1,4 cyclohexadiene, cyclohexene, styrene) and photodegradation of organic pollutants (phenol, methyl orange) from water. The re-sults showed improving of activity and selectivity in oxidation reactions by addition of the second metal to Ta-MCM-41 catalyst. The slow addition of H2O2 was also be benefit for the selectivity in epoxide products and stability of the catalysts. The band gap energy values decrease in the presence of the second metal and the band edge diagram evidenced posi-tive potential for all the conduction band of the bimetallic samples except TaTi-MCM-41. The higher photocatalytic degradation was obtained for samples with TaTi and TaV.

The aim of this work is to synthesis and characterize the Ta/TaN multilayer thin film coatings on 52100 tool steel under three different levels of N2 gas flow rate. The High Power Impulse Magnetron Sputtering (HiPIMS) technique was used for the deposition of Ta/TaN thin film multilayers on the substrate. Microstructure, coating thickness, composition, hardness and tribological properties of Ta/TaN multilayer coatings were characterized using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester and pin-on-disc tester, respectively. Adhesion property was evaluated via scratch testing of the thin film thin film layer. The lowest coefficient of friction was observed with the thin film layer of higher N2 gas flow rate due to the highest adhesion value of the coating on the surface. The obtained results on hardness, adhesion and coefficient of friction properties demonstrated that this Ta/TaN multilayer thin film coating can be used for tribological applications.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with a different N₂ flow rate of 0, 12, 17, 25, 38, 58 sccm. The effects of N₂ flow rate on the electrical properties, crystal structure, elemental composition and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of the N₂ flows. On the other hand, the resistivity increases, the crystal size decreases, and the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta₃N₅ (130,040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N₂ flow rates, and dependent on the crystal size and crystal phase structure.

This study aimed to characterize the long non-coding RNA (lncRNA) expression in the bovine mammary gland and to infer their functions in dietary response to 5% linseed oil (LSO) or 5% safflower oil (SFO). Twelve cows (six per treatment) in mid lactation were fed a control diet for 28 days followed by a treatment period (control diet supplemented with 5% LSO or 5% SFO) of 28 days. Mammary gland biopsies were collected from each animal on day-14 (D-14, control period), D+7 (early treatment period) and D+28 (late treatment period) and were subjected to RNA-Sequencing and subsequent bioinformatics analyses. Functional enrichment of lncRNA was performed via potential cis regulated target genes located within 50 Kb flanking regions of lncRNAs and having expression correlation of >0.7 with mRNAs. A total of 4955 lncRNAs (325 known and 4630 novel) were identified which potentially cis targeted 59 and 494 genes in LSO and SFO treatments, respectively. Enrichments of cis target genes of lncRNAs indicated potential roles of lncRNAs in immune function, nucleic acid metabolism and cell membrane organization processes as well as involvement in Notch, cAMP and TGF-β signaling pathways. Thirty-two and 21 lncRNAs were differentially expressed (DE) in LSO and SFO treatments, respectively. Six genes (KCNF1, STARD13, BCL6, NXPE2, HHIPL2 and MMD) were identified as potential cis target genes of six DE lncRNAs. In conclusion, this study indicated potential roles for lncRNAs in mammary gland immune functions and development and provided potential candidate genes and pathways via which lncRNAs can function in diet responses.

Adlay (Coix lachryma-jobi L. var. ma-yuen Stapf) contains various phytonutrients for treating many diseases in Asia. To investigate whether orally administered of adlay bran oil (ABO) can cause drug interactions, the effects of ABO on the pharmacokinetics of five cytochrome P450 (CYP) probe drugs were evaluated. Rats were given a single oral dose (2.5 mL/kg BW) of ABO 1 h before administration of a drug cocktail either orally or intravenously, and blood was collected at various time points. A single oral dose of ABO administration did not affect the pharmacokinetics of five probe drugs when given as a drug cocktail intravenously. However, ABO increased plasma theophylline, dextromethorphan, and diltiazem when co-administered an oral drug cocktail. After 7-days of feeding with an ABO-containing diet, plasma concentrations of theophylline and chlorzoxazone were increased after oral administration of drug cocktail. The major CYP enzyme activities in liver and intestinal were not affected by ABO treatment. Results from this study indicate that a single oral dose or short-term administration of ABO may increase plasma drug concentrations when ABO is given concomitantly with drugs. ABO is likely to enhance intestinal drug absorption. Therefore, caution is needed to avoid food-drug interactions between ABO and co-administered drugs.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

Tantalum doped ZnO structures (ZnO:Ta) were synthesized and some of their characteristics were studied. ZnO material was deposited on silicon substrates by using a hot filament chemical vapor deposition (HFCVD) reactor. The raw materials were a pill made of a mixture of ZnO and Ta₂O₅ powders, and molecular hydrogen was used as a reactant gas. Percentage of tantalum was varied from 0 to 500 mg by varying the percentage of tantalum oxide in the mixture of the pill source, by holding a fixed amount of 500 mg of ZnO in all experiments. X-ray diffractograms confirmed the presence of zinc oxide in the wurtzite phase and metallic zinc with a hexagonal structure, and no other phase was detected. Displacements to lower angles of reflection peaks, compared with those from samples without contamination, were interpreted as the inclusion of the Ta atoms in the matrix of the ZnO. This fact was confirmed by EDS and XRD measurements. From SEM images from undoped samples exhibited mostly micro sized semi-spherical structures while doped samples displayed a trend to grown as nanocrystalline rods. The presence of tantalum during the synthesis affects the way of the growth. Green photoluminescence at naked eye was observed when Ta doped samples were illuminated by ultraviolet radiation and confirmed by PL spectra. PL intensity on Ta doped ZnO varied from those undoped samples up to 8 times.

Siliceous sandstones used in Khmer temples such as the Prasat Basset, Wat Ek Phnom, Phnom Banan temples in Battambang Province, Phnom Chisor and Ta Prohm temples in Ta Keo Province, and Wat Nokor Bachey temple in Kampong Cham Province in Cambodia were investigated in this study. Chemical composition analyses and magnetic susceptibility measurements were conducted for the sandstone blocks used in these temples. Siliceous sandstone is a primary construction material in all investigated temples. Two types of siliceous sandstone, pale brown and red, were found. Pale brown siliceous sandstone was used for the construction of all the investigated temples. In contrast, red siliceous sandstone was found only in the Wat Ek Phnom, Prasat Basset, and Phnom Banan temples. It is suggested that the pale brown siliceous sandstone originated from the Phra Wihan Formation within the Khorat Group. Based on the chemical composition analysis, the pale brown siliceous sandstone in the Ta Prohm temple at Tonle Bati and the Wat Nokor Bachey temple may have been sourced from the lower level of the Phra Wihan Formation. In contrast, the pale brown siliceous sandstone used in the Prasat Basset, Wat Ek Phnom, and Phnom Banan temples was likely sourced from the upper level. The origin of the red siliceous sandstone is proposed to be from the Sao Khua Formation, which is situated above the Phra Wihan Formation.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Pipe leakage is an inevitable phenomenon in water distribution networks (WDNs), leading to energy waste and economic damage. Leakage events can be reflected quickly by pressure values, and the deployment of pressure sensors is significant for minimizing the leakage ratio of WDNs. Concerning the restriction of realistic factors, including project budgets, available sensor installation locations, and sensor fault uncertainties, a practical methodology is proposed in this paper to optimize pressure sensor deployment for leak identification in terms of these realistic issues. Two indexes are identified to evaluate the leak identification ability, that is, detection coverage rate (DCR) and total detection sensitivity (TDS), and the principle is to determine priority to ensure an optimal DCR and retain the largest TDS with an identical DCR. Leakage events are generated by a model simulation and the essential sensors for maintaining the DCR are obtained by subtraction. In the event of a surplus budget, and if we suppose the partial sensors have failed, then we can determine the supplementary sensors that can best complement the lost leak identification ability. Moreover, a typical WDN Net3 is employed to show the specific progress, and the result shows that the methodology is largely appropriate for real projects.

In emergency scenarios service vehicles must identify potential route(s) and use the best available route. However, route identification requires intelligent decision-support systems which generally use non-traditional approaches with tools characterised by flexible non-hierarchical structures. Conventional models using group decision-support systems have been applied; however, when used in smart urban environments, emergency response services have limitations in their ability to identify unobstructed paths (routes) in dynamic operating environments. In this paper we introduce a novel path planning method for autonomous vehicle control in emergency situations. The proposed model uses self-organizing maps in an integrated Spiral STC algorithm termed the: Hybrid SOM-Spiral STC model which uses hedge algebras and \emph{Kansei} evaluation in group decision-support. The proposed model has been designed to quantify qualitative factors using sensor derived data processed with human sensibilities and preferences in emergency decision support. The experimental results show that the proposed model achieves significant improvements in group decision-support under dynamic uncertainty. We posit that our novel approach holds the prospect of improvements in the provision of emergency services.

Robotic decision-support systems must facilitate a robots interactions with their environment, this demands adaptability. Adaptability relates to awareness of the environment and `self-awareness', human behaviour exemplifies the concept of awareness to arrive at an optimal choice of action or decision based on reasoning and inference with learned preferences. A similar conceptual approach is required to implement awareness in autonomous robotic systems which must adapt to the current dynamic environment (the context of use). By incorporating `self-awareness' with knowledge of a Robot's preferences (in decision making) the decision maker interface should adapt to the current context of use. This paper proposes a novel approach to enable an autonomous robotics which implements path planning combining adaptation with knowledge reasoning techniques and hedge algebra to enable an autonomous robot to realise optimal coverage path planning under dynamic uncertainty. The results for a cleaning robot show that using our proposed approach demonstrated the capability to avoid both static and dynamic obstacles while achieving optimal path planning with increased efficiency. The proposed approach achieves the multiple decision-making objectives (path planning) with a high-coverage and low repetition rates. Compared to other current approaches, the proposed approach has demonstrated improved performance over the conventional robot control algorithms.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

Accurate localization of road agents is the basis of intelligent transportation systems, which is still difficult to achieve for GNSS positioning in urban areas due to the signal interferences from buildings. Various collaborative positioning techniques are recently developed to improve the positioning performance by the aid from neighboring agents. However, it is still challenging to study their performances comprehensively. The GNSS measurement error behavior is complicated in urban areas and unable to be represented by naive models. On the other hand, real experiment requiring numbers of devices is hard to be conducted, especially for a large-scale test. Therefore, a GNSS realistic urban measurement simulator is developed to provide measurements for collaborative positioning studies. The proposed simulator employs a ray-tracing technique searching for all possible interferences in the urban area. Then, it categorizes them into direct, reflected, diffracted, and multipath signal to simulate the pseudorange, carrier-phase, 〖C/N〗_0, and Doppler shift measurements correspondingly. The performance of the proposed simulator is validated through real experimental comparisons with different scenarios. The proposed simulator is also applied with different positioning algorithms, which verifies it is sophisticated enough for the collaborative positioning studies in the urban area.

Our previous retrospective observational study demonstrated the safety of laparoscopically assisted subtotal colectomy with ileorectal anastomosis and preservation of the superior rectal artery (SRA), without instances of leakage, in patients with slow-transit constipation (STC). Thus, we extended the enrollment period and enlarged the sample size to detect the differences in the post-operative complications, and surgical and functional outcomes between patients who underwent laparoscopically assisted subtotal colectomy with and without SRA preservation. We conducted a retrospective single-center analysis of patients with STC who underwent laparoscopically assisted subtotal colectomy between 2016 and 2020. The diagnosis of STC was based on the colonic transit and anal functional tests, and barium enema to exclude secondary causes. Patients were divided into group A that underwent surgery with SRA preservation, and group B that underwent ligation of the SRA during surgery. Outcome assessments for both groups included the incidence of anastomotic breakdown, intraoperative complications, length of hospital stay, estimated blood loss, time to first flatus, and complications. Propensity-score matching allocated 34 patients to groups A and B each. Postoperative bowel function, including time to first flatus, stool, and oral intake, recovered better in group A than that in group B. Anastomotic leakage, a significant postoperative complication, was less frequent in patients with SRA preservation. Preservation of the SRA in patients undergoing laparoscopically assisted subtotal colectomy with ileorectal anastomosis for STC is associated with favorable postoperative bowel function recovery and lower anastomotic leakage rates.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

Traveling salesman problems (TSPs) are well-known combinatorial optimization problems, and most existing algorithms are challenging for solving TSPs when its scale is large. To improve the efficiency of solving large-scale TSPs, this work presents a novel adaptive layered clustering framework with improved genetic algorithm (ALC\_IGA). The primary idea behind ALC\_IGA is to break down a large-scale problem into a series of small-scale problems. First, the $k$-means and improved genetic algorithm are used to segment the large-scale TSPs layer by layer and generate the initial solution. Then, the developed two phases simplified $2$-opt algorithm is applied to further improve the quality of the initial solution. The analysis reveals that the computational complexity of the ALC\_IGA is between $O(n\log n)$ and $O(n^2)$. The results of numerical experiments on various TSP instances indicate that, in most situations, the ALC\_IGA surpasses the state-of-the-art algorithms in convergence speed, stability, and solution quality. Specifically, the ALC\_IGA can solve instances with $2 \times 10^5$ nodes within 0.15h, $1.4 \times 10^6$ nodes within 1h, and $2 \times 10^6$ nodes in three dimensions within 1.5h.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

The key issue in the post-genomic era is how to systematically describe the association between small molecule transcripts or translations inside cells. With the rapid development of high-throughput “omics” technologies, the achieved ability to detect and characterize molecules with other molecule targets opens up the possibility of investigating the relationships between different molecules from a global perspective. In this article, a Molecular Associations Network(MAN) is constructed and comprehensively analyzed by integrating the associations among miRNA, lncRNA, protein, drug, and disease, in which any kind of potential associations can be predicted. More specifically, each node in MAN can be represented as a vector by combining two kinds of information including the attributes of the node itself (e.g. sequences of ncRNAs and proteins, semantics of diseases and molecular fingerprints of drugs) and the manner of the node in the complex network (associations with other nodes). Random Forest classifier is trained to classify and predict new interactions or associations between biomolecules. In the experiment, the proposed method achieves a superb performance with 0.9735 AUC in 5-fold cross-validation, which show that the proposed method can provide new insight for exploration of the molecular mechanisms of disease and valuable clues for disease treatment.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&amp;S), (ii) mechanical alloying with press and sintering (MA + P&amp;S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting &lt; MA + P&amp;S &lt; BE + P&amp;S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.

MicroRNAs (miRNAs) are small endogenous RNAs that regulate gene expression post-transcriptionally by targeting either the 3′ untranslated or coding regions of genes. They have been reported to play key roles in a wide range of biological processes. The recent remarkable developments of transcriptomics technologies, especially next-generation sequencing technologies and advanced bioinformatics tools, allow more in-depth exploration of messenger RNAs (mRNAs) and non-coding RNAs (ncRNAs) including miRNAs. These technologies have offered great opportunities for a deeper exploration of miRNA involvement in farm animal diseases, as well as livestock productivity and welfare. In this review, we provide an overview of the current knowledge of miRNA roles in farm animal diseases with a particular focus on diseases of economic importance. In addition, we discuss the steps and future perspectives of using miRNAs as biomarkers and molecular therapy for livestock disease management as well as the challenges and opportunities for understanding the regulatory mechanisms of miRNAs related to disease pathogenesis.

Tourism Geographers in Anglo-American geographical departments migrate to teach and research tourism in applied schools and departments such as business, resource and environment, and even cultural and creative industry. Under national research assessment and funding pressures, tourism geographers are not encouraged to keep on undertaking serious theoretical researches related to their mother discipline and transferred to research applied researches and publish in hybrid journals. Such changes in tourism geographers` research behavior have not been tested and reported in Asian academic contexts, especially Taiwan while frequently being discussed internationally. This research aims to investigate the differences in the research behavior of tourism geographers between those who are staffed in geography departments and those who migrate to applies departments such as tourism and recreation, resource and environment, and others in terms of publishing journals, paradigmatic approaches, research types(qualitative, quantitative, and mixed), research methods and geographical scales conducted based on content analysis of articles published by tourism geographers in geography and tourism and recreation departments. This study revealed that there are significant differences in the research behavior of tourism geographers between different department. Finally, this paper explains the differences in terms of Taiwan changing social and economic conditions, academic traditions and politics of geography and applied departments, research habits and preferences of tourism geographers among departments and other aspects. This study can help international tourism geography academic circles to understand the complexity and diversity of tourism geography academic landscape of the Chinese language.

Comprehensively understanding the spatial ecology and habitat preferences of endangered species is essential for population restoration and conservation. We investigated the home range and movement of the endangered Amur soft-shell turtle (Pelodiscus maackii) in the Ussuri River, Heilongjiang Province, Northeastern China. The study involved tracking 19 Amur soft-shell turtles from late June to mid-October, 2022, resulting in complete and partial home range size data for eight subadults and two adults, respectively. The primary analysis focused on eight subadults, and the models that best described daily movement were identified. We also explored the potential factors influencing home range size. Mean movement rate ranged from 39.18 ± 20.04 m to 72.45 ± 29.36 m and was positively correlated with the linear home range and water temperature. The most insightful home range estimate was a 95% kernel density estimate, employing likelihood cross-validation smoothing with constraints set to the river boundaries. The mean home range size was 1.02 ha and was not correlated with body size. Subadults tended to establish well-defined home ranges over time; whereas, defining home ranges for adults proved challenging. This research addresses a gap regarding the ecology of the Amur soft-shell turtle and provides a foundation for future conservation plans.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

We employed the Riemannian Face Manifold (RFM) as an alternative approach to the conventional linear Euclidean space for explaining the atypicality bias in face likeliness judgments. The RFM posits that the mental representation of faces is better captured as a manifold of stable states, accounting for the nonlinearity in the physical properties of faces. To examine the relationship between physical and psychological distance of morph and typical/atypical faces, we manipulated the parameter k and incorporated a weight function in the Riemannian metric. Our results indicate that the psychological distance between the morph and typical face was longer than that between the morph and atypical face, consistent with prior research on the atypicality bias in perceptual similarity. The RFM approach provides mathematical support and is a powerful tool for studying face perception and recognition, offering potential implications for explaining the other-race effect. Future research can utilize the RFM to investigate individual differences in face recognition abilities and expertise, and how they impact psychological distance and face processing.

Most machine learning and deep learning algorithms can only use low-dimensional data as input, but the data that must be processed in practical applications is diverse and irregular. There are two main problems with big dynamic data. (1) The size of the embedding table grows linearly with the vocabulary size, resulting in massive memory consumption. (2) For different newly added vocabularies. To solve these two problems, this paper proposes a novel embedding algorithm that can learn attribute associations with entities based on deep and hash algorithms. Taking movie data as an example, the encoding method and the specific flow of the algorithm are presented in detail, and the effect of dynamic reuse of data models is realized. Compared with the four existing embedding algorithms which can fuse entity attribute information, the deep hash embedding algorithm proposed in this paper has obvious optimization of time and space complexity.

Despite the ecological importance of forest tree species, our study was motivated by scarce data on dendrochronology studies limited to the northwestern part of Tajikistan due to lack of access to such a part of the country which is difficult to access. Current studies on Junipers in the northwestern part of Tajikistan identified that tree ring-based climate reconstruction is possible. Cores of Juniperus Turkestanica from Taboshar area, Sogd province were developed into 176-year tree-ring width chronology. In the current study a summer (June-September) minimum temperature reconstruction spanning AD 1840–2016 was developed, which can explain 30.0% of the instrumental variableness for the period of 1940–2015. Five warmest (1856–1866, 1869–1871, 1907–1916, 1923–1935, 1988–2016) and four coldest time periods (1840–1855, 1872–1906, 1917–1922, 1940–1984) were identified. The developed reconstruction coincides with cold and warm periods with prior investigations from tree-rings in China, Mongolia, Kyrgyzstan, Kazakhstan and Tajikistan. Spatial correlation analysis with the gridded minimum temperature data shows that the temperature reconstruction covers geographical representation over High Asia. Significant correlation was found between temperature reconstruction with summer SST, which suggests strong linkages of regional temperature variability with Indian-Ocean climate system. The obtained spectral peaks from the spectral analysis of the summer temperature reconstruction were significantly at 84.7-year (90%), 2.9-year (99%), 2.6-year (99%), 2.5-year (99%), 2.4-year (99%) and 2.2-year (99%).

The shift towards lean production is gradually replacing traditional mass production, and lean accounting is also being mentioned to evaluate operational efficiency based on the lean philosophy, eliminating waste, and simplifying direct cost aggregation along the value stream to improve productivity, distribution, quality, and service. This study aims to evaluate the impact of various factors on the adoption of lean accounting in Vietnamese garment firms, based on data collected from 242 survey questionnaires completed by managers and accountants of Vietnamese garment firms. Through Cronbach's Alpha test, EFA test, and multiple regression analysis to verify and forecast information, eight determinants affecting the adoption of Lean Accounting in Vietnamese garment firms are arranged in descending order of influence, including Leadership, Size, Cost of implementation, Resources, Accounting department, Education and training, Culture, and Competitive pressure. Based on the findings, recommendations are proposed to management businesses and agencies to address shortcomings in the process of applying lean accounting, contributing to making it one of the most effective tools in promoting product development and continuous improvement, enhancing quality and production efficiency.

This investigation introduces an efficient method for assessing the reliability of semi-rigid steel frame connections in existing buildings, explicitly targeting the Top Angle and Seat Pad (TA-SP) semi-rigid connection commonly used in Australian cities' high-rise buildings. The moment capacity of these connections was examined through parameter power model testing, meticulously considering the bending, shear, and prying forces actions to determine the weakest elements in the connection system. A plastic hinge model was applied to ensure computational efficiency and accuracy in assessing the connections' ultimate strength. Comparatively, the finite element (F.E) method M−θ curves were introduced to scrutinise the nonlinear behaviour of the connection, providing validation for the predicted analytical approach. Further emphasis was placed on identifying the reliability of the weakest elements in the connection system, employing the First-Order and Second-Order Reliability Methods models to estimate their reliability index. The correlation between the model's failure probability and a percentile error was also explored, utilising Monte Carlo simulation reference for refined validation. Novel formulas and methodologies were introduced to compute the locked-chain-series system reliability, which accounts for the inherent material and geometric variability. The findings highlight the critical significance of the weakest element in determining the overall reliability of the existing TA-SP connection.

Garnet-type Ta-doped Li7La3Zr2O12 (LLZO) ceramic solid electrolytes with Ga2O3 additive were synthesized via a conventional solid-state reaction process. When the amounts of Ga2O3 additive were below 2 mol %, the sintered sample has a dense structure composed of grains with the averaged size of 5 to 10 μm, while 3 mol % or more Ga2O3 addition causes the significant increase in grain size above several 10 to 100 μm, due to the sintering with large amount of liquid Li-Ga-O phase at high temperature. The highest total (bulk + grain-boundary) ionic conductivity of 1.1 mS cm1 at room temperature was obtained in the sample with 5 mol % Ga2O3 addition. However, in galvanostatic testing of the symmetric cell with Li metal electrodes, this sample was shorted by Li dendrite growth into solid electrolyte at current density below 0.2 mA cm2. The tolerance for Li dendrite growth is maximized in sample sintered with 2 mol % Ga2O3 addition, which was shorted at 0.8 mA cm2 in the symmetric cell. Since the interfacial resistance between Li metal and solid electrolyte was nearly identical among the all samples, the difference in tolerance for Li dendrite growth is mainly attributed to the difference in microstructure of sintered samples depending on the amounts of Ga2O3.

The pandemic SARS-CoV-2 continues to evolve to give rise to variants of concern that can escape vaccine-induced immunity. As such, more effective vaccines are urgently needed. In this study, we evaluated virus-like particle (VLP) as a vaccine platform for SAS-CoV-2. The spike, envelope, and membrane proteins of the SARS-CoV-2 Wuhan strain were expressed by a single recombinant baculovirus BacMam and assembled into VLPs in cell culture. The morphology and size of the SARS-CoV-2 VLP as shown by transmission electron microscopy was found to be similar to the authentic SARS-CoV-2 virus particle. In a mouse trial, two intramuscular immunizations of the VLP BacMam with no adjuvant elicited spike-specific binding antibodies in both sera and bronchoalveolar lavage fluids. Importantly, BacMam VLP -vaccinated mouse sera showed neutralization activity against SARS-CoV-2 spike pseudotyped lentivirus. Our results indicated that the SARS-CoV-2 VLP BacMam stimulated spike-specific immune responses with neutralization activity.

During the Covid-19 pandemic in Taiwan, analytical tools of PEST (political, economic, social-cultural, and technological), SWOT (strength, weakness, opportunity, threat), nine building blocks of a business model canvas, and knowledge management were combined to develop a theoretical framework, and used to assess business, smart and sustainable management of two case companies: Tung Sheng Company Limited and its subsidiary, Strong Basic Enterprise Limited. A heuristic inquiry research design was adopted. In addition to secondary data from the two case companies, major top managers were interviewed to reveal constructive questions about the existing business models and to re-interpret strategy. The results showed that case companies own capabilities of R &amp; D (research and development) as a foundation to further apply new smart ICT (information and communication technology) and execute green manufacturing. Additionally, strong key partnerships are used to diversify business investment for leveraging on limited resources given current insufficient qualified employees. Resilient practices adopted new and green technology to help mitigate the negative impacts of the Covid-19 pandemic. This study provides a useful framework and practical information about how to examine business models, smart and sustainable management processes of the two case companies and to make adjustments in strategies for the future.

Cervical cancer is a common malignancy in women and has a poor prognosis.More and more studies have shown that autophagy disorder is closely related to the occurrence of tumors. However, the prognostic role of autophagy gene in cervical cancer is still unclear. In this study, we constructed the risk signatures of autophagy related genes to predict the prognosis of cervical cancer. The expression profiles and clinical information of autophagy gene sets were downloaded from the TCGA and GES52903 queues as training sets and validation sets. The cervical normal tissue expression profile data from UCSC XENA website is GTEx data as a supplement to TCGA normal cervical tissue. Univariate COX regression analysis of 17 different autophagy genes with the Consensus approach tumor samples from the TCGA is divided into six subtypes, and the clinical traits in the six subtypes have different distribution, with further then absolute shrinkage and selection operator (LASSO) and multiariable COX regression method finally got seven autophagy genetic risk model is constructed, in the training set, the survival rate of high risk group is lower than the low risk group (p < 0.0001), the validation set,The AUC area of the receiver operating characteristic (ROC) curve, the training set is 0.894, and the verification set is 0.736. We find that the high and low risk score is closely related to the TMN stage (All P is less than 0.05).The nomogram shows that the risk score combined with other indicators such as age, G,T,M, and N better predicts 1-year, 2-year, 3-year survival, and the DCA curve shows that the risk model combined with other indicators produces better clinical efficacy.Then immune cells in 28 in the enrichment score, there were statistically significant differences, high and low risk most GSEA enrichment analysis, the main enrichment in G2 / M checkpoint high-risk score, Genes defining epithelial and mesenchymal transition, raised in response to the low oxygen levels (hypoxia) gene, gene is important to the mitotic spindle assembly, these are closely related with the occurrence of tumor . In conclusion, our constructed autophagy risk signature may be a prognostic tool for cervical cancer.

In this paper, we shall introduce the interval-valued spatial error model. Based on the idea of least square method of single-valued case, we give the parameter estimator for interval-valued spatial error model. The theoretical properties of the proposed estimator are proved. Finally, we give the numerical analysis and a real example.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

Protein import into the endoplasmic reticulum (ER) is the first step in the biogenesis of about 10,000 different soluble and membrane proteins in humans. It involves co- or post-translational targeting of precursor polypeptides to the ER and their subsequent membrane insertion or translocation. So far, three pathways for ER targeting of precursor polypeptides plus four pathways for ER targeting of mRNAs were described. Typically, these pathways deliver their substrates to the Sec61 polypeptide-conducting channel in the ER membrane. Next, the precursor polypeptides are inserted into the ER membrane or translocated into the ER lumen, which may involve auxiliary translocation components, such as the TRAP and Sec62/Sec63 complexes, or auxiliary membrane protein insertases, such as EMC and the TMCO1 complex. Recently, the PEX19/PEX3-dependent pathway, which has a well-known function in targeting and inserting various peroxisomal membrane proteins into pre-existent peroxisomal membranes, was also found to act in targeting and, putatively, inserting monotopic hairpin proteins into the ER. These either remain in the ER as resident ER membrane proteins or are pinched off from the ER as components of new lipid droplets. Therefore, the question arose if this pathway may play a more general role in ER protein targeting, i.e. represents a fourth pathway for ER targeting of precursor polypeptides. Thus, we addressed the client spectrum of the PEX19/PEX3-dependent pathway in both PEX3-depleted HeLa cells and PEX3-deficient Zellweger patient fibroblasts by an established approach, which involves label-free quantitative mass spectrometry of the total proteome of depleted or deficient cells and differential protein abundance analysis. The negatively affected proteins included twelve peroxisomal proteins and two hairpin proteins of the ER, thus confirming two previously identified classes of putative PEX19/PEX3-clients in human cells. Interestingly, fourteen collagen-related proteins with signal peptides or N-terminal transmembrane helices and belonging to the secretory pathway were also negatively affected by PEX3-deficiency, which may suggest compromised collagen biogenesis as a hitherto unknown contributor to organ failures in the respective Zellweger patients.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

The need to address climate change and establish sustainable urban environments has driven increased efforts in Europe to develop climate-neutral cities. This study highlights the importance of integrating solar energy technologies and nature-based solutions as key strategies to achieve climate neutrality. By examining current practices, emerging trends, and case examples, it explores the benefits, challenges, and prospects associated with the integration of solar energy and nature-based solutions in urban contexts. The study presents a pioneering approach to assess the urban heat and climate change mitigation benefits of combining building-integrated photovoltaics and nature-based solutions specifically within the European context. The results emphasize the synergistic relationship between nature-based components and solar conversion technology, identifying effective combinations for different climatic zones. In warmer regions of Southern Europe, strategies like rooftop photovoltaics on cool roofs, photovoltaics shadings, green walls, and urban trees have demonstrated effectiveness. Conversely, mid- and high-latitude European cities have seen positive impacts through the integration of rooftop photovoltaics and photovoltaics facades with green roofs and green spaces. As solar cell conversion efficiency improves, the environmental impact of photovoltaics is expected to decrease, facilitating their integration into urban environments. The study emphasizes the importance of incorporating water bodies, cool pavements, spaces with high sky-view factors, and effective planning in urban design to maximize resilience benefits. It also highlights the significance of prioritizing mitigation actions in low-income regions and engaging citizens in the development of social photovoltaics positive energy houses, resilient neighbourhoods, and green spaces. By adopting these recommendations, European cities can lead the way in creating climate-neutral urban environments that prioritize clean energy, nature-based solutions, and the overall well-being of residents. The findings underscore the need for a multidisciplinary approach that combines technological innovation, urban planning strategies, and policy frameworks to effectively achieve climate neutrality in European cities.

A enantioselective tandem transformation concerning asymmetric allylic decarboxylative addition and cyclization of N-nosylimines with vinylethylene carbonates (VECs) in the presence of [Rh(C2H4)2Cl]2, chiral sulfoxide-N-olefin tridentate ligand has been developed. The reaction of VECs with various substituted N-nosylimines proceeded smoothly under mild conditions, giving highly functionalized oxazolidine frameworks in good to high yields with good to excellent enantioselectivity.

Objective: To explore the inflammatory markers for the development of obliterative bronchiolitis (OB) after adenovirus infection in children. Methods: In this retrospective study, the medical data of 62 children with adenovirus pneumonia treated in our hospital between February 2020 and November 2021 were collected and assigned to an OB group (n = 30) or non-OB group (n = 32) according to the presence of OB. Clinical characteristics of patients included gender, age, prematurity, underlying disease, length of hospitalization, type of adenovirus infection, ventilator use, length of ventilator use, and laboratory index levels. Results: Children with OB were associated with higher serum ferritin levels versus those without (P < 0.05). There were no significant differences in the immunoglobulin E (IgE), interleukin-6 (IL-6), partial arterial pressure of oxygen (PaO₂), D-dimer, lactate dehydrogenase (LDH), and lymphocyte absolute values between the two groups of children (P > 0.05). Logistic multifactorial regression analysis revealed that the length of ventilator use and serum ferritin level were inflammatory markers for the development of OB in children with adenovirus pneumonia. Conclusion: The length of ventilator use and serum ferritin levels are inflammatory markers for the development of OB after adenovirus infection in children, and timely measurement of the above indicators in children is instrumental in predicting the prognosis of children.

In considering knowledge graphs in a diverse range of domains of interest, graph neural networks have demonstrated significant improvements in node classification and prediction when applied to graph representation with learning node embedding to effectively represent hierarchical properties of graphs. DiffPool is a deep-learning approach using a differentiable graph pooling technique that generates hierarchical representations of graphs. In operation DiffPool is a differentiable graph pooling technique that generates hierarchical representations of graphs. DiffPool learns a differentiable soft cluster assignment for nodes at each layer of a deep graph neural network with nodes mapped sets of clusters. However, control of the learning process is difficult given the complexity and large number of parameters on an `end-to-end’ model. To address this difficulty we propose an novel approach termed FPool which is predicated on the basic approach adopted in DiffPool (where pooling is applied directly to node representations). Methods designed to enhance data classification have been developed and evaluated using a number popular and publicly available sensor data sets. Experimental results for FPool demonstrate improved classification and prediction performance when compared to alternative methods. Moreover, FPool shows an important reduction in the training time over the basic DiffPool framework.

Robotic path planning is a field of research which is gaining traction given the broad domains of interest to which path planning is an important systemic requirement; the aim being to optimise the efficacy of robotic movements in a defined operational environment. For example, robots have been employed in many domains including: cleaning robots (such as vacuum cleaners), automated paint spraying robots, window cleaning robots, forest monitoring robots, agricultural robots (often driven using satellite and geostationary positional satellite data). Additionally, mobile robotic systems have been utilised in disaster areas and locations hazardous to humans (such as war zones in mine clearance). The coverage path planning problem describes an approach which is designed to determine the path that traverses all points in a defined operational environment while avoiding static and dynamic (moving) obstacles. In this paper we present our proposed Smooth-STC model, the aim of the model being to identify an optimal path, avoid all obstacles, prevent (or at least minimise) backtracking, and maximise the coverage in any defined operational environment. The experimental results in a simulation show that, in uncertain environments, our proposed smooth STC method achieves an almost absolute coverage rate and demonstrates improvement when measured against alternative conventional algorithms.

Precision and accuracy estimation is an important index used to reflect the measurement performance and quality of a measurement system. To reveal the significance and connotations of the precision and accuracy estimation index of a close-range photogrammetry system, several common precision and accuracy estimation methods used in close-range photogrammetry are explained from a theoretical perspective, and the mechanism of the internal coincidence precision estimation and the external coincidence accuracy estimation are deduced, respectively. Through detailed experimental design and testing, the validity and reliability of the proposed precision and accuracy estimation methods are verified, which provides strong evidence for the quality control, optimisation, and evaluation of the measurement results from a close-range photogrammetry system. At the same time, it has significance for the further development of precision and accuracy estimation analysis of close-range photogrammetry systems.

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from the zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration induced flow, which has been challenging due to its unsteady nature. Validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field induced around a cylindrical micropillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micropillar becomes stationary, and the result was converted to the Eulerian frame to compare them with the experimental results. The present approach enables to avoid the introduction of moving boundary or small perturbation approximation. The flow field obtained by the micro particle image velocimetry (PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in the microfluidic systems.

The irradiation biology of the brown marmorated stink bug (BMSB, Halyomorpha halys Stål) treated at the nymphal stage was investigated to determine its application for sterile insect technique (SIT). Fifth instar males of BMSB were exposed to gamma-radiation 60Co at different doses of 12, 16, 20, 24 and 64 Gy. Irradiated males were mated with non-irradiated virgin females to assess the longevity of both sexes, female fecundity and fertility of their offspring until the egg stage of the F2 generation. The mortality of each of the developmental stages of the F1 and eggs of the F2 generation was observed to determine whether negative effects from exposure to radiation was inherited. The data indicated that irradiation significantly reduced the lifespan of male insects at doses above 20Gy. Irradiated males did not affect the longevity and fecundity of their female partners, nor either sex of their resulting progeny, but it did reduce the hatch rate of the eggs at all doses tested. The sterility rates of F1 eggs were 55.6%, 73.3%, 74.1% and 74.1% at doses of 12Gy, 16Gy, 20Gy and 24Gy respectively. Eggs were completely sterile (100%) at a dose of 64Gy with no egg hatch recorded. A low hatch rate of F2 eggs illustrated that negative effects from radiation was inherited by the subsequent generation. The results support the potential for the use of SIT for BMSB management by irradiating the fifth instar male nymphs at 16-64Gy.

INTRODUCTION: The purpose of the study was to determine (a) the overall preclinical character; (b) the cumulative cutoff values and the risk ratio, and (c) the factors associated with severity by a unidimensional and multidimensional analysis on 2173 Sars-Cov2 patients. METHODS: The machine learning study population consisted of 2173 patients (1587 mild and non symptoms patients, 377 moderate patients, 209 severe patients). The status of the patients was recorded from September 2021 to March 2022. RESULTS: The Covid19 Severity directly links with a significant correlation to Age, Score index of the chest X-ray, percentage and quantity of neutrophils, Albumin, C reactive protein, and ratio of Lymphocytes. Their important cut off values (from regression analysis) respectively are: 77.56 years old (the mild-moderate group), 5.53 (the mild-moderate group) and 10.51 (the moderate-severe group), 84.80% (the mild-moderate group) and 87.74%(the moderate-severe group), 11.77G/L (the moderate-severe group), 29.73g/L (the moderate-severe group), 7.46mg/dL (the mild-moderate group), 6.32% (the moderate-severe group). Their significant (p<0.0001) R score correlation with the severity of Covid19, are: 0.44, 0.52 and 0.52, 0.33 and 0.44, 0.42, -0.43, 0.40, -0.41. Their significant risk ratio (p<0.00001) from the meta-analysis, respectively are: 4.19 [3.58-4.95], 3.29 [2.76-3.92] and 3.03 [2.4023;3.8314], 3.18 [2.73-3.70] and 3.32 [2.6480;4.1529], 3.15 [2.6153;3.8025], 3.4[2.91-3.97], 0.46 [0.3650;0.5752] (p<0.00001), 0.34 [0.2743;0.4210]. The pair ALT – Leucocytes and Transferrin – Anion Chloride get the most important correlation shift. ALT – Leucocytes show the important negative link (R=-1, p<0.00001) in the mild group to the significant positive correlation in the moderate group (R=1, p<0.00001). Transferrin–anion Chloride has an important positive association (R=1, p<0.00001) in the mild group with a significant negative correlation in the moderate group (R=-0.59, p<0.00001). The network map and HCA show that in the mild-moderate group, the closest neighbors with the Covid19 severity are ferritins, Age. Then there is C-reactive protein, SI of X-ray, Albumin, and Lactate dehydrogenase, which are the next close neighbors of these three factors. In the moderate-severe group, the closest neighbors with the Covid19 severity are Ferritin, Fibrinogen, Albumin, the quantity of Lymphocytes, SI of X-ray, white blood cells count, Lactate dehydrogenase, and quantity of neutrophils. CONCLUSIONS: Complete multidimensional study in 2173 Covid19 patients in Vietnam shows the whole picture of all the preclinical factors, which may become the clinical reference marker for surveillance and diagnostic management

14-Deoxy-11,12-didehydroandrographolide (deAND), a diterpenoid in Andrographis paniculata (Burm. f.) Nees, acts as a bioactive phytonutrient that can treat many diseases. To investigate the protective effects of deAND on reducing fatty liver disease, male mice were fed a high-fat and high-cholesterol (HFHC) diet without or with 0.05% and 0.1% deAND supplementation. Cholesterol accumulation, antioxidant and anti-inflammatory activities in liver and liver injury were evaluated after deAND treatment. The results show that deAND treatment for 7 weeks reduced plasma alanine aminotransferase activity and lowered hepatic cholesterol accumulation, tumor nuclear factor-α, and histological lesions. 0.1% deAND treatment reduced HFHC diet-induced apoptosis by lowering the caspase 3/pro-caspase 3 ratio. After 11-weeks of deAND treatment, increased NOD-like receptor protein 3 (NLRP3), capase-1, and interleukin-1β protein levels in liver were suppressed by deAND treatment. In addition, nuclear factor erythroid 2-related factor 2 (Nrf2) mRNA expression, heme oxygenase-1 protein expression, and the activities of glutathione peroxidase and glutathione reductase were increased in mice fed the HFHC diet. However, those activities of antioxidant enzymes or proteins were also upregulated by 0.1% deAND treatment. Furthermore, deAND treatment tended to lower hepatic lipid peroxides. Finally, deAND treatment reversed the depletion of hepatic glutamate level induced by HFHC diet. These results indicate that deAND may ameliorate HFHC diet-induced steatohepatitis and liver injury by increasing antioxidant and anti-inflammatory activities.

In the early stage of new vehicle development, the requirements of maximum performance of the air conditioning (AC) system are obtained through Amesim software simulation, but the calibration control of the AC system is usually carried out in the prototype-build vehicle test stage, and the test time is spanned up to 10 months after spring (autumn), summer and winter, of which up to 2 months are for environment chamber tests. Due to the long calibration cycle of AC control in the road test, which seriously affects the vehicle launch time, virtual calibration technology of air conditioning system is developed to shorten the calibration cycle of AC systems and ensure the quality of vehicles. In the project development stage, the calibration control of the vehicle AC system can be realized to carry out the functional test of the AC system in advance. In that, the grade of maturity for the AC system control can be improved, the on-road calibration test cycle can be shortened, and the development cost can be saved.

Arthropods, the most abundant group in ecosystems, play crucial roles in human production. Soil physicochemical properties reflect soil health and are linked to arthropods through cascading effects. Gravel-sand mulching, commonly practiced in dry farming regions, initially aids in water retention and temperature regulation. However, long-term cultivation can lead to land degradation and habitat fragmentation. This study aimed to investigate field systems using multiple comparison, linear, and nonlinear correlation analyses to explore the effects of different tillage durations on soil properties and arthropod diversity under gravel-sand mulching. Results indicate that arthro-pod diversity was lower while the fields maintained better soil fertility than the desert steppe. Both soil fertility and arthropod diversity declined significantly with increased years of cultivation. Mantel tests revealed no significant response of desert steppe arthropods to the altered soil properties of gravel-sand mulched fields. However, the Generalized Additive Model analysis indicated significant linear correlations between arthropod occurrence and total nitrogen (positive), available phosphorus, and water content (negative). Arthropod abundance showed significant nonlinear correlations with total potassium, alkali hydrolyzable nitrogen, and organic matter (OM), with OM changes having the most pronounced impact. Thus, gravel-sand mulching can maintain soil fertility over time but at the expense of local arthropod diversity.

The risk of lung exposure to silica nanoparticles (SiNPs) and related lung inflammatory injury is increasing with the wide application of SiNPs in a variety of industries. A growing body of research has revealed that cyclooxygenase (COX)-2/ prostaglandin E2 (PGE2) up-regulated by SiNPs toxicity has a role during pulmonary inflammation. The detailed mechanisms underlying SiNPs-induced COX-2 expression and PGE2 synthesis remain unknown. The present study aims to dissect the molecular components involved in COX-2/PGE2 up-regulated by SiNPs in human pulmonary alveolar epithelial cells (HPAEpiCs) which are one of the major targets while SiNPs are inhaled. In the present study, we demonstrated that SiNPs induced COX-2 expression and PGE2 release, which were inhibited by pretreatment with a reactive oxygen species (ROS) scavenger (edaravone) or the inhibitors of proline-rich tyrosine kinase 2 (Pyk2, PF-431396), epidermal growth factor receptor (EGFR, AG1478), phosphatidylinositol 3‑kinase (PI3K, LY294002), protein kinase B (Akt, Akt inhibitor VIII), p38 mitogen-activated protein kinase (MAPK) (p38 MAPK inhibitor VIII), c-Jun N-terminal kinases (JNK)1/2 (SP600125), Forkhead Box O1 (FoxO1, AS1842856), and activator protein 1 (AP-1, Tanshinone IIA). In addition, we also found that SiNPs induced ROS-dependent Pyk2, EGFR, Akt, p38 MAPK, and JNK1/2 activation in these cells. These signaling pathways induced by SiNPs could further cause c-Jun and FoxO1 activation and translocation from the cytosol to the nucleus. AP-1 and FoxO1 activation could increase COX-2 and PGE2 levels induced by SiNPs. Finally, the COX-2/PGE2 axis might promote the inflammatory responses in HPAEpiCs. In conclusion, we suggested that SiNPs induced COX-2 expression accompanied by PGE2 synthesis mediated via ROS/Pyk2/EGFR/PI3K/Akt/p38 MAPK- and JNK1/2-dependent FoxO1 and AP-1 activation in HPAEpiCs.

Stress relaxation tests in cantilever bending were performed on the C7025 and C7035 alloys at 298K and 393K，respectively. The effect of stress-relief treatments on stress relaxation properties was investigated. The structural changes associated with the stress relaxation process were examined using transmission electron microscope. The stress relaxation curve fits well to empirical formula σ*=[Kˊln(t+α₀)+C]^-n for stress relaxation. The curves can be split into two stages. The stress relax quickly in the first stage, slows down in the second stage, and tends to be a certain limit value after a long time. The curve and microstructure reveals that the C7035 alloy has a lower rate of stress relaxation and a higher anti-stress relaxation capacity than the C7025. The first reason is that the movement of vacancies required by spinodal decomposition is inhibited, and the quantity of cobalt -containing vacancies decreases dramatically in the C7035 alloy. The other reason is that the precipitated phases became uniformly diffused in the C7035 alloy. The precipitate phase uniformly distributes in the grain boundaries and the matrix, during the relaxed condition, and thus the dislocations moving is blocked by the precipitates.

EGFR mutations are heterogenous but all carry the same weighting in the Lung-molGPA. The aim of this study was to elucidate the different prognostic implications of molecular subtypes and frontline TKIs in EGFR-mutated lung adenocarcinoma with synchronous brain metastases (BM) using the Lung-molGPA. Medical records were searched in hospital databases from 2011 to 2015. Patients with EGFR-mutated adenocarcinoma and brain metastases who received TKIs were included. The Kaplan-Meier method was used to estimate survival, and multivariate Cox proportional hazard models were used to estimate adjusted hazard ratios (HRs) and 95% confidence intervals (CIs). A total of 256 patients were included with a median overall survival (OS) of 17.2 months. In multivariate analysis of OS, only age (70 versus &lt;70 years, HR:1.71, 95% CI:1.25-2.35, p&lt;0.001), KPS (&lt;70 versus 70, HR:1.71, 95% CI:1.26-2.31, p&lt;0.001), and rare mutations (other versus exon 19 deletions, HR:1.78, 95% CI:1.04-3.05, p=0.037) remained statistically significant. In patients with a Lung-molGPA score 2.5, EGFR molecular subtypes had different median OS (exon 19 deletions versus Leu858Arg versus other, 18.8 vs 12.4 vs 12.1 months, p=0.021). In conclusion, different molecular subtypes treated with frontline TKIs have different prognostic implications in the Lung-molGPA. Further prospective studies are warranted to validate these findings.

Smart health applications have received significant attention in recent years. Novel applications hold significant promise to overcome many of the inconveniences faced by persons with disabilities throughout daily living. For people with blindness and low vision (BLV), environmental perception is compromised, creating myriad difficulties. Precise localization is still a gap in the field and is critical to safe navigation. Conventional GNSS positioning cannot provide satisfactory performance in urban canyons. 3D mapping-aided (3DMA) GNSS may serve as an urban GNSS solution, since the availability of 3D city models has widely increased. As a result, this study developed a real-time 3DMA GNSS-positioning system based on state-of-the-art 3DMA GNSS algorithms. Shadow matching was integrated with likelihood-based ranging 3DMA GNSS, generating positioning hypothesis candidates. To increase robustness, the 3DMA GNSS solution was then optimized with Doppler measurements using factor graph optimization (FGO) in a loosely-coupled fashion. This study also evaluated positioning performance using an advanced wearable system’s recorded data in New York City. The real-time forward processed FGO can provide a root-mean-square error (RMSE) with about 21 m. The RMSE drops to 16 m when the data is post-processed with FGO in a combined direction. Overall results show that the proposed loosely-coupled 3DMA FGO algorithm can provide a better and more robust positioning performance for the multi-sensor integration approach used by this wearable for persons with BLV.

Ca-bentonite (CB) alone and in a mixture with limestone (L), tobacco biochar (TB) and zeolite (Z) on the fixation, geochemical fractions and absorption of Cd and Zn by Chinese cabbage in smelter heavily polluted (S-HP) and smelter low polluted (S-LP) soils were investigated. The results showed that the CB+TB and CB+L+TB treatments significantly immobilized Cd up to 22.03% and 29.68%, respectively, and reduced uptake by Chinese cabbage shoot to 35.98% with CB+Z+L and 61.35% with CB+L in S-HP and S-LP soils compared with the control. The CB+ Z+ L+TB treatment mobilized Cd up to 4.45% and increased absorption in the shoot by 9.85% in S-HP soil. The greatest immobilization of Zn was 53.18% and 58.20% with the CB+Z+L+TB treatment, which reduced Zn uptake in the plant shoot by 9.94% with CB + L and 58.04 with CB+Z+L+TB in S-HP and S-LP soils. The CB+Z+TB and CB+TB treatments mobilized Zn up to 35.40% and 4.80%, respectively, in both soils. Furthermore, the uptake of Zn in plant shoot was observed by 58.96% and 7.82% with application of CB+Z and CB+TB treatments, respectively, in S-HP and S-LP soils. Overall, our results suggest that Ca-bentonite alone and in mixtures with different amendments can be used to reduce the phyto-extraction of Cd and Zn in Zn-smelter polluted soils.

Corals are an important habitat for a diverse fauna which is especially rich in branching species. Each colony harbors several species and dozens of individuals forming an integrated symbiotic community. Factors affecting the diversity and abundance of coral symbionts are poorly understood. The present study tested experimentally the relationship between the population density of coral Pocillopora verrucosa and the diversity and abundance of symbionts in planted coral fragments exposed during three months. Colony size and bleaching were also considered as two additional factors. We demonstrated that even at the early stage of the colonies’ formation, the diversity of obligate symbiontson on these corals was higher than in any other studied local faunas of the World Ocean.Species richness and abundance of symbionts were positively related to colony size and density, while no impact of bleaching was found. Species richness and abundance of obligate symbionts increased along with the host population density, while in facultative symbionts, these indexes decreased. We hypothesized that the negative effect of the host density on species richness and abundance of facultative symbionts is caused by the competitive pressure of obligates, which increases with their abundance. Reasons for the different responses of obligate and facultative symbionts to host density were considered.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.