We analyze the thermal convection thresholds and linear characteristics of the primary and secondary instabilities for viscoelastic fluids saturating a porous horizontal layer heated from below by a constant flux. Galerkin method is used to solve the eigenvalue problem by taking into account the elasticity of the fluid, the ratio between the viscosity of the solvent and the total viscosity of the fluid and the lateral confinement of the medium. For the primary instability, we found out that depending on the rheological parameters, two types of convective structures may appear when the basic conductive solution loses its stability: stationary long wavelength instability as for Newtonian fluids and oscillatory convection. The effect of the lateral confinement of the porous medium by adiabatic walls is to stabilize the oblique and longitudinal rolls and therefore selects transverse rolls at the onset of convection. In the range of the rheological parameters where stationary long wave instability develops first, we use a parallel flow approximation to determine analytically the velocity and temperature fields associated to the monocellular convective flow. The linear stability analysis of the monocellular flow is performed, and the critical conditions above which the flow becomes unstable are determined. The combined influence of the viscoelastic parameters and the lateral confinement on the characteristics of the secondary instability is quantified. The major new findings concerning the secondary instabilities may be summarized as follows: (i) For concentrated viscoelastic fluids, computations showed that the most amplified mode of convection corresponds to oscillatory transverse rolls which appears via a Hopf bifurcation. This pattern selection is independent of both the fluid elasticity and the lateral confinement of the porous medium; (ii) For diluted viscoelastic fluids, the preferred mode of convection is found to be oscillatory transverse rolls for a very laterally confined medium. Otherwise stationary or oscillatory longitudinal rolls may develop depending on the fluid elasticity. Results also showed the destabilizing effect of the relaxation fluid elasticity and the stabilizing effect of the viscosity ratio for the onset of both primary and secondary instabilities.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

Natural radioactivity of 238U, 232Th and 40K for liquid and solid samples collected from Sidi Salem dam (Tunisia) and Aïn Dalia dam (Algeria) were measured using TERRA detector of rays (gam-ma, beta, and alpha), Atomic adsorption and Gamma-ray spectrometry were used to analyze the levels of radionuclides and toxic heavy metals, respectively. Toxic heavy metals (Fe, Bb, Zn, Ni, Cu, Cr and Cd) and associated health risks in surface water and sediment of dams have been in-vestigated in this present study. The radioactivity mean rates in the water samples were 1.72±0.01, 0.068±0.01 and 94.6±1.04 Bql-1 for 238U, 232Th and 40K respectively (Tunisia dam) and were 1.9± 0.24, 0.09±0.01 and 131.43±1.03 Bql-1 for 238U, 232Th and 40K respectively (Algeria dam). The 238U, 232Th and 40K radioactivity mean concentration measured in the sediment samples were 2.67±0.01, 0.18±0.012 and 197.87±2.01 Bqkg-1 respectively (Tunisian dam) and were 4.34±0.05, 0.27±0.05 and 287.61±3.34 Bqkg-1 respectively (Algeria dam). The activity concentration of 40K was higher than that of 238U and 232Th for the water and sediment samples. The mean activity concen-trations follow the order 40K > 238U > 232Th. The cumulative impact can be a serious immediate radiological health burden on the ecosystem, environment and people's health in this study area and can be transposable to any other similar region. The good knowledge of monitoring quality and quantity for the transboundary water resources and the international collaborations are es-sential to safeguard human health (women’s breasts cancer, thyroid cancer, neurological im-pact…), and avoid the conflicts, especially during these climatic upheavals of drought.

Metal 3D printing technology is a promising manufacturing method, especially in the case of complex shapes. The quality of the printed product is still a challenging issue for mechanical applications. The anisotropy of the microstructure, imperfections, and residual stress are some of the issues that diminish the mechanical properties of the printed sample. The simulation could be used to investigate some technical details, and this research has tried to computationally study the metal 3D printing of austenitic stainless steel to address austenite microstructure and local yield strength. Two computational codes were developed in Visual basics 2015 to simulate the local heating/cooling curve and subsequent austenite microstructure. A stochastic computational code was developed to simulate austenite grain morphology based on calculated thermal history. Then Hall-Pitch equation was used to estimate the yield strength of the printed sample. These codes were used to simulate the effect of temperature of the printer’s chamber on microstructure and subsequent yield strength. The austenite grain topology is more columnar at a lower temperature. The percentage of the equiaxed zone will be increased at a higher chamber’s temperature. Almost a fully equiaxed austenite microstructure will be achieved at 800 C chamber’s temperature, but the last printed layer, which is columnar and can be removed by cutting then. The estimated local austenite grain size and the local yield strength in the equiaxed regions are in the range of 15 to 30 μm and 270 to 330 MPa at 800 C temperature of printer’s chamber, respectively.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

Computer simulation relies on well-defined experimental supported theories, models, and numerical methods. Computer simulation is an alternative to fill the gaps where the experiment is pricy or limited in engineering. Computer simulation is a high-fidelity computational technique that can work as an engineering innovation tool to try imaginative ideas beyond the available technologies. The accuracy of current computer simulation results is reliable enough to accelerate innovation for new materials and mechanical technologies without experimental validation. So, we may need to urge relying on computer simulation results without any experimental validation to accelerate engineering innovations. In addition, using high-fidelity computer simulation for engineering innovation acceleration without validation will be promoted if it is credited as a new classification. This subject and a related justification's classification in engineering have been discussed.

The Sol Hamed (SH) area is a part of the Arabian-Nubian Shield (ANS) ophiolites occurred within Onib-Sol Hamed suture zone in the southern Eastern Desert of Egypt. The ophiolitic assemblages in this area are represented by serpentinite, metagabbro and arc assemblages represented by metavolcanics. They later intruded by gabbroes and granites. Geochemically, the compatible trace elements (Cr=2426–2709 ppm, Ni=1657–2377 ppm and Co=117–167 ppm) enrichment in SH serpentinites indicate derivation from a depleted mantle peridotite source. They show affinity to the typical metamorphic peridotites. The normative compositions reflect harzburgitic mantle source. Their Al2O3 contents (0.05–1.02 wt. %) are akin to oceanic and active margin peridotites and Pan-African serpentinites. The Cr and TiO2 contents indicate supra-subduction zone (SSZ) environment. Their Al2O3/SiO2 and MgO/SiO2 ratios support the SSZ affinity and are similar to ANS peridotites with fore-arc setting. Moreover, their Al2O3 and CaO depletion is typical of fore-arc peridotites. Structurally, the area represents four deformational events can be well-known in the Neoproterozoic rocks (D1, D2, D3 and D4); D1: E–W thrust faults and related E–W (F1) folds; D2: NW–SE thrust faults and related NW–SE (F2) folds were formed; D3: conjugate NNW-trending sinistral and NNE-trending dextral transpression, as well as N–trending tight folds (F3) and D4: is E–W dextral strike-slip and dip-slip normal faults striking NNW–SSE to N–S and E–W may be related to Red Sea rifting. There are major three fault sets affected the area. The first set trend mainly NE-SW and is manifested in the volcanic-sedimentary assemblage and Gabal SH and have important role in mineralization. The second set trend E-W affecting all the basement rocks and disturbs the first fault set. The third set trend N-S affected all the rock units. Magnesite mineralization in SH serpentinites is cryptocrystalline formed due to hydrothermal alteration of the serpentinite host rocks. It is occur as snow-white veins and stock-works. These characteristics are typical of Kraubath type magnesite deposits. Gold mineralization is confined to malachite-bearing quartz veins, smoky quartz veins and alteration zones. Malachite-bearing quartz veins trending NW-SE cut through gabbroic rocks and exhibit mylonitic structure. They are fractured containing malachite and disseminated sulfide minerals. Smoky quartz veins trending NE-SW with SE steeply dipping intrude the meta-andesite. They are intensively sheared containing iron oxides in the fissures. The gold grades increase with arsenopyrite occurrences. On the other hand, the barren quartz veins are nearly vertical with E-W directions. Alteration zones with NW-SE trend and nearly vertical dip intrude metagabbros and metavolcanics. Hematite, limonite, goethite and fresh pyrite characterize these zones. They occur mainly neighboring the auriferous quartz veins.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

We present software on total energy calculation by quantum mechanics first principle method with a graphic user interface (GUI). Total energy calculation in this software is based on numerical analysis of time-dependent density functional (the used numerical method is finite difference time domain). QUMEC package has been equipped by common exchange-correlation energy terms with electron spin polarization calculation. With this package, users can calculate the total energy of the free particle, bulk materials, and materials with free surfaces at the atomic scale. The package is tested by several physical subjects, i.e., the surface energy of nano-LiCoO₂ and diffusion constant of lithium atoms in LiNi­_0.5Mn_1.5O₄.

This code provides computational facilities to simulate current versus time during the charging of Li-ion cells at desire constant voltage by considering multiscale physical phenomena. This code only considers a powder of active materials (at microscale or nanoscale) and a small part of electrolyte around it as a half cell. Then it is extended to a complete cell by applying correct boundary conditions. This code is very useful by modifying code parameters to understand the effect of the complex shape of active materials powder (surface area and powder size), kind of electrolyte, and the applied voltages on the charging response of Li-ion cell. As a summary, a microscale approach to the design of Li-ion cells has been provided via this code.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

Alzheimer's disease (AD) is a progressive neurodegenerative brain disorder. One of the important therapeutic approaches of AD is the inhibition of β‐site APP cleaving enzyme‐1 (BACE1). This enzyme plays a central role in the synthesis of the pathogenic β-amyloid peptides (Aβ) in Alzheimer's disease. A group of potent BACE1 inhibitors with known x-ray structures (PDB ID 5i3X, 5i3Y, 5iE1, 5i3V, 5i3W, 4LC7, 3TPP) were studied by molecular dynamics simulation and binding energy calculation employing MM_GB(PB)SA. The calculated binding energies gave Kd values 0.139 µM, 1.39 nM, 4.39 mM, 24.3 nM, 1.39 mM, 29.13 mM and 193.07 nM, respectively. These inhibitors showed potent inhibitory activities in enzymatic and cell assays. The Kd values were compared with experimental values, the structures were discussed in view of the energy contributions to binding. Drug likeness of these inhibitors is also discussed. Accommodation of ligands in the catalytic site of BACE1 is discussed depending on the type of fragment involved in each structure. Molecular dynamics (MD) simulations and energy studies were used to explore the recognition of the selected BACE1 inhibitors by Asp 32, Asp228 and the hydrophobic flap. The results show that selective BACE1 inhibition may be due to the formation of strong electrostatic interactions with Asp32 and Asp228 and a large number of hydrogen bonds, π-π and Van der Waals interactions with the amino acid residues located inside the catalytic cavity. Interactions with the ligands show a similar binding mode with BACE1. These results help to rationalize the design of selective BACE1 inhibitors.

We present a precise and universal method for anticipating the thermodynamic characteristics of polyatomic molecules. Unlike conventional computational approaches that rely on numerous experimental spectroscopy or calorimetry data, our model only utilizes a small number of molecular constants. We accurately predicted the values of entropy, enthalpy, specific heat, and Gibbs free energy for boron trifluoride, which were in excellent accordance with the available experimental data. This investigation introduces a new approach to deal with the anharmonic vibrations of polyatomic molecules

Ferric uptake regulation protein is a repressor protein which binds an AT rich region of DNA (the iron box). Fur binds as a dimer in a helix turn helix mode and it is activated by iron(II) and other divalent transition metal ions at elevated concentrations in a process to regulate the ion uptake. Each transition metal ion induces certain conformational changes to aid the Fur binding, both the N-terminal and C-terminal domains take part in binding to DNA in addition to His 88 and His 86 residues. The process is discussed in view of experimental reports. Fe(II), Mn(II) and Co(II) activate Fur to bind DNA experimentally but Zinc plays a structural role and does not activate Fur to bind DNA.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

We present theoretical designs of high performance optical filters in integrated silicon photonic nanowire resonators. We use mode interference in formed by zig-zag waveguide coupled Sagnac loop reflectors (ZWC-SLRs), tailored to achieve diverse filtering functions with good performance. These include compact bandpass filters with improved roll-off, optical analogues of Fano resonances with ultrahigh spectral extinction ratios (ERs) and slope rates, and resonance mode splitting with high ERs and low free spectral ranges. The analysis verifies the feasibility of multi-functional integrated photonic filters based on ZWC-SLR resonators for flexible spectral engineering in diverse applications.

Deep Learning (DL) oriented document processing is widely used in different fields for extraction, recognition, and classification processes from raw corpora of data. The article examines the application of deep learning approaches, based on different neural network methods, including Gated Recurrent Unit (GRU), Long Short-Term Memory (LSTM), and Convolutional Neural Networks (CNN). The compared models were combined with two different word embedding techniques, namely: Bidirectional Encoder Representations from Transformers BERT and Gensim Word2Vec. The models are designed to evaluate the performance of architectures based on neural network techniques for the classification of CVs of Moroccan engineering students at ENSAK(National School of Applied Sciences of Kenitra, Ibn Tofail University). The used dataset included resumes collected from engineering students at ENSAK in 2023 for a project on the employability of Moroccan engineers in which new approaches were applied, especially machine learning, deep learning, and big data. Accordingly, 867 resumes were collected from five specialties of study (Electrical Engineering, Networks and Systems Telecommunications, Computer Engineering, Automotive Mechatronics Engineering, Industrial Engineering). The results revealed good performance of the proposed models based on the BERT embedding approach compared to models based on the Gensim Word2Vec embedding approach. Accordingly, the CNN-GRU/Bert model achieved slightly better accuracy with 0.9251 compared to other hybrid models.

We propose and theoretically investigate integrated photonic filters based on coupled Sagnac loop reflectors (SLRs) formed by a self-coupled wire waveguide. By tailoring coherent mode interference in the device, three different filter functions are achieved, including Fano-like resonances, wavelength interleaving, and varied resonance mode splitting. For each function, the impact of device structural parameters is analyzed to facilitate optimized performance. Our results theoretically verify the proposed device as a compact multi-functional integrated photonic filter for flexible spectral shaping.

We theoretically investigate integrated photonic resonators formed by two mutually coupled Sagnac loop reflectors (MC-SLRs). Mode interference in the MC-SLR resonators is tailored to achieve versatile filter shapes with high performance, which enable flexible spectral engineering for diverse applications. By adjusting the reflectivity of the Sagnac loop reflectors (SLRs) as well as the coupling strength between different SLRs, we achieve optical analogues of Fano resonance with ultrahigh spectral slope rates, wavelength interleaving / non-blocking switching functions with significantly enhanced filtering flatness, and compact bandpass filters with improved roll-off. In our designs the requirements for practical applications are considered, together with detailed analyses of the impact of structural parameters and fabrication tolerances. These results highlight the strong potential of MC-SLR resonators as advanced multi-functional integrated photonic filters for flexible spectral engineering in optical communications systems.

This paper presents a novel adaptive fault-tolerant neural-based control design for wind turbines with unknown dynamic and unknown wind speed. By utilizing the barrier Lyapunov function in the analysis of the Lyapunov direct method, the constrained behavior of the system is provided in which the rotor speed, its variation and generated power remain in the desired bounds. In addition, input saturation is also considered in terms of smooth pitch actuator bounding. Furthermore, by utilizing a Nussbaum-type function in designing the control algorithm, the unpredictable wind speed variation is captured without requiring accurate wind speed measurement, observation or estimation. Moreover, with the proposed adaptive analytic algorithms, together with the use of radial basis function neural networks, a robust adaptive and fault-tolerant control scheme is developed without the need for precise information about the wind turbine model nor the pitch actuator faults. Additionally, the computational cost of the resultant control law is reduced by utilizing a dynamic surface control technique. The effectiveness of the developed design is verified using theoretical analysis tools and illustrated by numerical simulations on a high-fidelity wind turbine benchmark model with different fault scenarios. Comparison of the achieved results to the ones that can be obtained via an available industrial controller shows the advantages of the proposed scheme.

Background: Twitter is a major tool for communication in emergencies such as natural disasters. This online social network allows the user to produce content, and it is not designed exclusively for news releases, as opposed to other service providers. Aim: The aim of this study is to investigate Twitter uses in natural disasters and pandemics. Methods: The included studies reported the role of Twitter in natural disasters. The studies that report in settings other than the natural disasters (such as man-made disasters) and other social media were excluded. Electronic databases for a comprehensive literature search including MEDLINE, Web of Science, CINAHL, PsycINFO, Cochrane Register of Controlled Trials (CENTRAL) and EMBASE were used to identify the records that match the mentioned inclusion criteria published till May 2020. The study characteristics were extracted from the qualified studies including year of publication, findings, and geographical location of the study conduct. A narrative synthesis for this literature review was used. Results: The search identified 822 articles of which 780 articles were removed, 256 were not available, 311 papers were not relevant, 16 were duplicated articles, and 197 were non-related to the emergencies. 45 articles met the selection criteria and were included in the review. eleven themes were found in the narrative synthesis including early warning, disseminating information and misinformation, advocacy, personal gains, assessment, various roles of organizations, public mood, geographical analysis, charity, using influencers, and trust. Conclusions: It is recommended that influential individuals be identified in each country and community before disasters occur so that the necessary information can be disseminated in response to disasters. Preventing the spread of misinformation is one of the most important issues in times of disaster, especially pandemics. Disseminating accurate, transparent, and prompt information from relief organizations and governments can help. Also, analyzing Twitter data can be a good source for understanding the mental state of the community, estimating the number of injured people, estimating the points affected by natural disasters, and modeling the prevalence of epidemics. Therefore, various groups such as politicians, the government, non-governmental organizations, aid workers, and the health system can use this information to plan and implement interventions.

Appeals to governments for implementing basic income are contemporary. The theoretical backgrounds of the basic income notion, only prescribe transferring equal amounts to individuals irrespective of their specific attributes. However, the most recent basic income initiatives all around the world are attached to certain rules with regard to the attributes of the households. This approach is facing significant challenges to appropriately recognize the vulnerable groups. A possible alternative for setting rules with regard to the welfare attributes of the households is to employ artificial intelligent algorithms that can process unprecedented amounts of data. Can integrating machine learning change the future of basic income by perdition of vulnerable to future poverty households? In this paper, we utilize a multidimensional and longitudinal welfare data comprising one and a half million individual data and a Bayesian beliefs network approach to examine the feasibility of predicting households’ vulnerability to future poverty based on the existing households’ welfare attributes.

Background: ChatGPT is becoming a new reality. Where do we go from here? Objective: to show how we can distinguish ChatGPT-generated publications from counterparts produced by scientist. Methods:By means of a new algorithm, called xFakeBibs, we show the significant difference between ChatGPT-generated fake publications and real publications. Specifically, we triggered ChatGPT to generate 100 publications that were related to Alzheimer’s disease and comorbidity. Using TF-IDF, using the real publications, we constructed a training network of bigrams comprised of 100 publications. Using 10-folds of 100 publications each, we also 10 calibrating networks to derive lower/upper bounds for classifying articles as real or fake. The final step was to test xFakeBibs against each of the ChatGPT-generated articles and predict its class. The algorithm successfully assigned the POSITIVE label for real ones and NEGATIVE for fake ones. Results: When comparing the bigrams of the training set against all the other 10 calibrating folds, we found that the similarities fluctuated between (19%-21%). On the other hand, the mere bigram similarity from the ChatGPT was only (8%). Additionally, when testing how the various bigrams generated from the calibrating 10-folds against ChatGPT we found that all 10 calibrating folds contributed (51%-70%) of new bigrams, while ChatGPT contributed only 23%, which is less than 50% of any of the other 10 calibrating folds. The final classification results using the xFakeBibs set a lower/upper bound of (21.96-24.93) number of new edges to the training mode without contributing new nodes. Using this calibration range, the algorithm predicted 98 of the 100 publications as fake, while 2 articles failed the test and were classified as real publications. Conclusions: This work provided clear evidence of how to distinguish, in bulk ChatGPT-generated fake publications from real publications. Also, we also introduced an algorithmic approach that detected fake articles with a high degree of accuracy. However, it remains challenging to detect all fake records. ChatGPT may seem to be a useful tool, but it certainly presents a threat to our authentic knowledge and real science. This work is indeed a step in the right direction to counter fake science and misinformation.

Lack of water resources in Iran, especially in recent years, has faced the agricultural sector as the most important consumer of water resources, with serious challenges. In Iran, the agricultural sector accounted for more than 90% of water consumption. However, the focus on domestic production and self-sufficiency policy in staples (wheat, barley, maize and rice) has been emphasized in general agriculture's policy. This study was conducted to estimate the imported virtual water from the imports of basic products in Iran using defined indicators during 1961-2013. Also this study investigated the possibility of achieving self-sufficiency due to the limited water resources in Iran. The results of this study showed with the increase in cereal imports, virtual water imports from 0.28 billion cubic meters in 1961 increased to 17.6 billion cubic meters in 2013 and on average about 60% of virtual water imports in strategic products is related to wheat imports during the past 53 years. Other products in cereal (barley, maize and rice) are also indicative of the general trend of increasing imports of virtual water in development plans. The estimated long-run elasticity of virtual water imports in the cereal group compared with the country's water resources also showed that with a one percent reduction in renewable water resources of the country, the virtual water import in the main cereal group will increase equivalent to 2.89 percent and the determination coefficient more than 90 percent also confirms this negative relationship. According to this result and the emphasis on the fact that renewable water resources per capita in the country is falling increasingly, it cannot be expected that domestic production could compensate for the imports of the cereal group and virtual water imports with current technology, without increasing the water productivity and without additional harm to water resources.

This paper presents the results of an experimental investigation about target detecting with passive sonar in Persian Gulf. Detecting propagated sounds in the water is one of the basic challenges of the researchers in sonar field. This challenge will be complex in shallow water (like Persian Gulf) and noise less vessels. Generally, in passive sonar the targets are detected by sonar equation (with constant threshold) which increase the detection error in shallow water. Purpose of this study is proposed a new method for detecting targets in passive sonars using adaptive threshold. In this method, target signal (sound) is processed in time and frequency domain. For classifying, Bayesian classification is used and prior distribution is estimated by Maximum Likelihood algorithm. Finally, target was detected by combining the detection points in both domains using LMS adaptive filter. Results of this paper has showed that proposed method has improved true detection rate about 27% compare other the best detection method.

Ion channels are integral membrane proteins that facilitate the movement of ions across cell membranes, playing a key role in a range of biological processes. The high cost and time required for wet lab experiments to characterize ion channels has spurred the development of computational methods for this purpose. In our previous work, we demonstrated the effectiveness of protein language models for ion channel prediction, using a logistic regression classifier to distinguish ion channels from non-ion channels (TooT-BERT-C) and transporters from non-transporters (TooT-BERT-T). In this study, we build upon this approach by using a combination of classical machine learning classifiers and a Convolutional Neural Network (CNN) with fine-tuned representations from ProtBERT, ProtBERT-BFD, and MembraneBERT to discriminate ion channels from non-ion channels. The results of our experiments demonstrate that TooT-BERT-CNN-C, a combination of the representations from ProtBERT-BFD and a CNN, outperforms existing state-of-the-art methods for predicting ion channels, with a Matthews Correlation Coefficient (MCC) of 0.86 and an accuracy of 98.35% on an independent test set.

Lake Manzala, the largest of the northern Delta lakes of Egypt, has a great economic importance as a major natural resource of fish and salt. Unfortunately, the lake is suffering from the high inputs of pollutants from industrial, domestic, and agricultural sources. The present study aims to develop the proposed water quality management scenarios to assess and control lake pollution, the pollution sources as well as the pollution spread from the lake to the connected Mediterranean Sea. To apply study methodology, the work tasks divided into two main parts, the first part involved in modelling the lake environments by using Delft3D-WAQ hydrodynamic and water quality model to study the current status and predict the dynamic state of the Lake. This model was calibrated and validated by using various water quality datasets to simulate different scenarios. In the second part, the required lake water quality improvement scenarios were developed to solve the lake water quality problems. The study results showed that the first three developed scenarios that focusing on treatment drain effluent using primary, secondary treatment and surface wetland techniques respectively have a limited efficiency on lake water quality improvement. While the fourth scenario that involved on using biological biofilm techniques can improve lake water quality parameters. Moreover, the fifth scenario that proposed adding a new artificial inlet has a limitation due to the noted increases in lake salinity levels. The sixth scenario that proposed a diversion of some drains can improve lake water quality parameters but it can lead to a decrease in Lake water level. From water quality view point, the last scenario that applying a combination biological biofilm activated technique and also adding a new artificial inlet at northern lake region can represent the optimum scenario. Hopefully, this research will preserve the lake environment and contribute to the benefit of the man health as well. This approach could be extended to the hydrodynamic studies in similar large, shallow lakes anywhere in the world.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

A series of supported CuO-based nanoparticle catalysts were prepared by impregnation method and used for the synthesis of glycerol carbonate from glycerol and CO2 in the presence of 2-cyanopyridine as a dehydrant and DMF as a solvent. The effects of supports (activated alumina, silicon dioxide, graphene oxide, graphene, and activated carbon), CuO loading amount, calcination temperature, and reaction parameters on the catalytic activity of catalyst were investigated in detail. XRD, FTIR, SEM, BET, and CO2-TPD were used for the characterization of the prepared catalysts. It is found that CuO/Al2O3 shows a higher catalytic activity, which depends on the CuO loading amount and calcination temperature. The surface area and amount of basic sites of the catalyst exhibit crucial effect on the catalytic activity of CuO/Al2O3. Furthermore, there is a synergistic effect between the catalyst and 2-cyanopyridine that the former has higher activation ability for glycerol and the latter acts not only as a dehydrant, but also as a promoter for CO2 activation. Recycling experiments reveal that this catalyst can be reused at least five cycles without any inactivation. Based on the experiment results and FTIR characterization, a possible reaction mechanism for the carbonylation of glycerol and CO2 is proposed.

Introduction the outbreak of the Israel-Gaza conflict, initiated by a major attack on the civilian population in Israel provided a tragic opportunity to study the community wide association between severe emotional stressors related to acts of war and the incidence and clinical characteristics of Takotsubo cardiomyopathy (TCM) in this scenario. Methods Eight consecutive cases of TCM diagnosed during the first 50 days of the Israel-Gaza conflict were retrospectively collected from two southern medical centers who provided care to most of the war victims throughout the period of monitoring. The medical records were thoroughly reviewed and analyzed. Results During the monitoring period, the incidence of TCM increased substantially compared to the control period. Eight patients were included in the analysis. All patients were female and 100% of patients presented within the first 3 weeks of conflict whereas after this initial phase, despite the continuing war, the incidence of TCM reverted to pre-conflict levels. Two patients (25%) were under 50 years of age. All patients had hazardous clinical characteristics including severe left ventricular (LV) dysfunction (≤35%) and prolonged QTc interval (>500 ms). Five patients (62.5%) experienced complications. Nevertheless, no in-hospital mortality was reported. Conclusions Repeated exposure to severe emotional stress, on both personal and national level, due to mass crisis such as war is associated with an increased incidence of TCM potentially with high-risk phenotype in comparison to TCM following other, less potent, psychological insults.

The dynamics of suspended sediment involves inherent non-linearity and complexity as a result of the presence of both spatial variability of the basin characteristics and temporal climatic patterns. As a result of this complexity, the conventional sediment rating curve (SRC) and other empirical methods produce inaccurate predictions. Deep neural networks (DNNs) have emerged as one of the advanced modeling techniques capable of addressing inherent non-linearity in hydrological processes over the last few decades. DNN algorithms are used to perform predictive analysis and investigate the interdependencies among the most pivotal water quantity and quality parameters i.e., discharge, suspended sediment concentration (SSC), and turbidity. In this study, the Long short-term memory (LSTM) algorithm of DNNs is used to model the discharge-suspended sediment relationship for the Stony Clove Creek. The simulations were run using primary data on discharge, SSC and turbidity. For the development of the DNN models and examining the effects of input vectors, combinations of different input vectors (namely discharge, and SSC) for the current and previous days are considered. Furthermore, a suitable modelling approach with an appropriate model input structure is suggested based on model performance indices for the training and testing phases. The performance of developed models is assessed using statistical indices such as root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). Statistically, the performance of DNN-based models in simulating the daily SSC performed well with observed sediment concentration series data. The study demonstrates the suitability of the DNN approach for simulation and estimation of daily SSC, opening up new research avenues for applying hybrid soft computing models in hydrology.

Recent astronomical observations with respect to measurements in distant supernovas, cosmic microwave background and weak gravitational lensing confirm that the Universe is undergoing a phase of accelerated expansion and it has been proposed that this cosmological behavior is caused by a hypothetical dark energy which has a strong negative pressure that allows explain the expanding universe. Several theoretical ideas and models related dark the energy includes the cosmological constant, quintessence, Chaplygin gas, braneworld and tachyonic scalar fields. In this paper, we have obtained new relativistic stellar configurations considering an anisotropic fluid distribution with a charge distribution which could represents a potential model of a dark energy star. In order to investigate the effect of a quadratic equation of state in this anisotropic model we specify particular forms for the gravitational potential that allow solving the Einstein-Maxwell field equations. For these new solutions we checked that the radial pressure, metric coefficients, energy density, anisotropy factor, charge density , mass function are well defined and are regular in the interior of the star. The solutions found can be used in the development of dark energy stars models satisfying all physical acceptability conditions but the causality condition and strong energy condition are violated. We expect that these models have multiple applications in astrophysics and cosmology.

Marketing is the manner of how to make our sales the best in the market, our prices the most accessible, our clients satisfactory, and thus our brand is the largest distributed. This needs sophisticated and advanced understanding of the total network related. Indeed, marketing data may be seen in different forms such as qualitative and quantitative. However, in the literature, it is easily noticed that large bibliography may be collected about qualitative studies, against few studies on the quantitative point of view. This is a major drawback that makes the marketing science still focusing on the design, although the market is strongly depending on quantities such as money and time. Indeed, marketing data may be a time series such as brand sales per specified periods, brand related-prices over specified periods, market shares, ..., etc. The purpose of the present work is to investigate some marketing models based on time series due to brands. We will precisely study the effect of the time scale on the persistence of brands sales in the market and on the forecasting of such a persistence according to the characteristics of the brand and the related market competition or competitors. Our study is acted on a sample of Saudi brands during the period November 22, 2017 to December 30, 2021.

Motivated for improving the efficiency and reliability of wind turbine energy conversion, this paper presents an advanced control design that enhances the power regulation efficiency and re-liability. The constrained behaviour of the wind turbine is taken into account, by using the barrier Lyapunov function in the analysis of the Lyapunov direct method. This, consequently, guarantees that the generated power remains within the desired bounds to satisfy the grid power demand. Moreover, a Nussbaum-type function is utilized in the control scheme, to cope with the unpre-dictable wind speed. This eliminates the need for accurate wind speed measurement or estimation. Furthermore, via properly designed adaptive laws, a robust actuator fault-tolerant capability is integrated into the scheme, handling the model uncertainty. Numerical simulations are performed on a high-fidelity wind turbine benchmark model, under different fault scenarios, to verify the effectiveness of the developed design. Also, a Monte-Carlo analysis is exploited for the evaluation of the reliability and robustness characteristics against the model-reality mismatch, measurement errors and disturbance effects.

In the present paper, we investigate the impact of the timescale factor on the quality of life index behavior on specific time intervals characterized by the presence of socio-economic, political, and/or health severe movements such as pandemics and crises. We essentially aim to show that effectively the quality of life measuring based on a single index in the existing studies may be described more adequately by a variable index due to the social, political, economic, and also healthy environment. The variability discovered is expressed by the existence and the estimation of a multi-index instead of a single one relatively to many factors. Our focus is mainly on the effect of the COVID-19 pandemic on the quality of life. Our model is applied empirically to a sample corresponding to Saudi Arabia as a case of study during the period from January 1990 to December 2021 as the main period affected by the COVID-19 pandemic. The sample is based on social media conversations and texts discussing and describing the satisfaction with the quality of life. The study confirms effectively that the role of the timescale factor is more described when considering a multi-index rather than measurement on the whole time interval.

Long-term health consequences are influenced by circumstances that occur during pregnancy. The confluence of the maternal and fetal circulations occurs at the placenta, which is the first or-gan to develop. Placental pathology can provide an accurate diagnosis of inflammation inside the amniotic sac. The pathological alterations of preterm placentas provide evidence for the causes of numerous perinatal pathologies, including spontaneous preterm births. This retrospec-tive study aimed to re-examine placentas regarded as normal by the Obstetrics and Gynecology Department in our institution so that grading and staging of any evident inflammatory response could be evaluated and associated with baby gender. Eighty-four full-term placentas were col-lected after delivery. Placentas that were considered normal and were not sent to the histo-pathology department were taken. Morphological examination of fresh placenta was conducted. Full thicknesses of placenta samples were taken from central and marginal regions of placental disc. Fetal and maternal inflammatory responses syndrome were assessed. Villitis of unknown etiology (VUE) and chronic deciduitis also were evaluated in the placenta. Immunohistochemis-try (IHC) was also performed to evaluate patterns of inflammation in the placenta using an-ti-CD8 and anti-CD68 antibodies. The correlation between the silent pathologies and clinical complications or involvement of developing fetal inflammatory response syndrome was meas-ured. In this study, seventeen (20%) maternal inflammatory samples and ten (12%) fetal inflam-matory samples showed inflammatory responses. The frequency of chronic deciduitis and villi-tis of unknown etiology was more remarkable among Saudi pregnant women than the previ-ously reported findings in the literature of placental pathology. The prevalence of fetal and ma-ternal inflammatory response was greater in the placentas of mothers of males than in placentas of female mothers. Grading placental inflammation usually predict the degree of maternal an-ti-fetal cellular rejection. Fetal inflammatory response syndrome usually goes unnoticed in Sau-di Arabia. There are differences in the inflammatory response in the placenta based on the sex of the newborn. Increasing the number of placental samples that must be sent for microscopic in-spection may be preferable due to their significance in identifying the causes of chronic disor-ders.

The classification of kidney tumors has undergone a remarkable evolution since the early 19th century, reflecting advances in medical science and technology. This historical overview traces the development of renal tumor classification, beginning with early clinical observations and macroscopic descriptions to the integration of molecular diagnostics in contemporary classifications. The establishment of international organizations like the World Health Organization (WHO) facilitated collaboration and standardization in tumor classification, leading to refined classifications and standardized nomenclature. Advancements in histological and molecular studies, particularly genetic analyses, revolutionized the understanding of renal cell carcinomas, enabling precise categorization based on molecular characteristics. The journey from rudimentary classifications to sophisticated systems based on detailed histological, immunohistochemical, and molecular criteria underscores the continuous evolution of kidney tumor classification. This article provides a comprehensive overview of this evolution, highlighting the contributions of scholars and the impact of technological advancements on our understanding and management of kidney tumors.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

In this paper, we present some new models for anisotropic compact stars within the framework of 5-dimensional Einstein-Gauss-Bonnet (EGB) gravity with a linear and nonlinear equation of state considering a metric potential proposed for Thirukkanesh and Ragel (2012) and generalized for Malaver (2014). The new obtained models satisfy all physical requirements of a physically reasonable stellar object. Variables as energy density, radial pressure and the anisotropy are dependent of the values of the Gauss-Bonnet coupling constant

In this paper, we found a new model for compact star with charged anisotropic matter distribution considering an extended version of the Chaplygin equation of state. We specify a particular form of the metric potential Z(x) that allows us to solve the Einstein-Maxwell field equations. The obtained model satisfies all physical properties expected in a realistic star such that the expressions for the radial pressure, energy density, metric coefficients, measure of anisotropy and the mass are fully well defined and are regular in the interior of star. The solution obtained in this work can have multiple applications in astrophysics and cosmology.

In this paper, we found new classes of exact models to the Einstein-Maxwell system of equations which describe the internal structure of a compact star made of strange matter considering the equation of state proposed by Rocha, Bernardo, de Avellar and Horvath in 2019. It has been assumed that this matter is composed of equal number of up, down and strange quarks and a small amount of electrons required to reaching the charge neutrality. If this hypothesis is correct, the neutron stars could be strange stars or hybrid stars with a thin crust of nuclei where the temperatures and pressures are capable of converting hadronic matter into this new stable phase of quarks. We have chosen a particular form of gravitational potential Z(x) that depends on an adjustable parameter related to degree of anisotropy of the models and the new solutions can be written in terms of elementary and polynomial functions. The obtained models satisfy all physical features expected in a realistic star and the expressions for mass, density and stellar radius are comparable with the experimental results.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Nanopeening treatment was applied to the AISI 420 steel to decrease its sensitivity to the tribocorrosion damage. Microstructural investigation highlighted that the Nanopeening treatment led to a high plastic deformation and nanostructured surface layer with 110 µm depth. . In order to study the combined effect of corrosion and mechanical wear, tribocorrosion tests were performed on non–treated and nanopeened samples in boric acid and lithium hydroxide solution, considering both continuous and intermittent sliding. It was found that the AISI 420 steel is sensitive the synergism between mechanical friction and electrochemical corrosion with a domination of abrasive wear. Adhesive wear was also detected in the wear track. Indeed, the mechanical wear was pronounced under intermittent sliding because of hard wear debris generation from the repassivated layer during rotating time. The Nanopeening treatment led to enhance mechanical performance and corrosion properties. Such improvement could be explained by the high plastic deformation resulting in the nano-structuration of grains and increasing hardness of AISI 420 steel.

New antibacterial agents are needed to overcome the increasing number of infectious diseases caused by pathogenic microorganisms due to the emergence of multi-drug resistant strains. In this context, halogens, especially Iodine is known since ages for its antimicrobial activity. Therefore, especially triiodides encapsulated in organometallic complexes can be helpful as new agents against microorganisms. The aims of this work was to study the biological activity of [Na(12-Crown-4)₂]I₃ against gram positive Streptococcus pyogenes, Streptococcus faecalis, the spore forming bacteria Bacillus subtilis and gram negative bacteria Escherichia coli, Proteus mirabilis, Pseudomonas aeruginosa and Klebsiella pneumoniae, as well as the yeast Candida albicans. The antimicrobial and antifungal activities of the triiodide were determined by zone of inhibition plate studies. [Na(12-Crown-4)₂]I₃ exhibited potent antimicrobial activity on gram positive Streptochocci and the yeast C. albicans. Furthermore, the gram negative bacteria P. aeruginosa and K. pneumoniae were less effectively inhibited, while E. coli and P. mirabilis proved to be even resistant.

Three different fields intersect in search of an understanding of the point-of-origin of modern-age diseases: 1) D-amino acids and their role under stress conditions; 2) evolutionary origin of the mitochondrion organelle in the eukaryotic cell; and 3) gut microbiota and human healthHere it is first suggested that D-amino acids function as universal signaling agents, after having evolved as prokaryotic communication, part of an organic communication process that governs the basic activities of all the cells and coordinates cell action.Mitochondria (symbiotic prokaryotic organelles), are creative source of D-amino acids as signaling agents in the central nervous system and in the neuroendocrine systems.Amino acids racemases catalyzes the conversion between the L-enantiomers ( protein building blocks) into D-enantiomers (signaling agents).It is suggested that hectic modern life may affect human health by causing stress to the gut microbiota. These affected, gut microbiota then secrete D-amino acids that enter the blood stream, as signaling agents, causing communication errors in the central nervous system, and in the neuroendocrine systems due to excessive quantity of D-amino acids.Treating gut microbiota with inhibitors of amino acids racemases or finding D-amino acid scavengers may be used in developing novel therapeutic strategies for diseases related to the central nervous system and neuroendocrine systems caused by stressed gut microbiota.

water resources in Morocco have been severely influenced by climate change (CC) and pro-longed drought, particularly, in the pre-Saharan zone. The Tafilalet region faces increasing pres-sure due to high demographic growth, increased demand for water, excessive groundwater con-sumption, and investment in agriculture. Using the Water Evaluation and Planning System (WEAP), this study assessed land cover and elevation and created future scenarios using the Standard Precipitation Index (SPI) and Standard Groundwater Level Index (SGI) to monitor hy-droclimate drought conditions in the Ziz watershed from 1989 to 2022. Results show decreasing precipitation, particularly from 2010-2020, with the last four years being the most challenging (SPI<-2). SPI and SGI have a high correlation, suggesting precipitation impacts groundwater in-dicators. Future scenarios predict a high risk of CC, with a 30% decrease in annual precipitation accumulation by 2100 under the optimistic scenario SSP126. Minimum temperature is expected to increase by 1.08°C (SSP126) and 2.61°C (SSP585), and maximum temperature by 1.05°C (SSP126) and 2.93°C (SSP585). Keywords: Climate Change, Water Resources, SPI, SGI, WEAP, Ziz watershed, Drought

The spread of the Coronavirus pandemic has been accompanied by an infodemic. The false information that is embedded in the infodemic affects people’s ability to have access to safety information and follow proper procedures to mitigate the risks. This research aims to target the falsehood part of the infodemic, which prominently proliferates in news articles and false medical publications. Here, we present NeoNet, a novel supervised machine learning text mining algorithm that analyzes the content of a document (news article, a medical publication) and assigns a label to it. The algorithm is trained by TFIDF bigram features which contribute a network training model. The algorithm is tested on two different real-world datasets from the CBC news network and Covid-19 publications. In five different fold comparisons, the algorithm predicted a label of an article with a precision of 97-99 %. When compared with prominent algorithms such as Neural Networks, SVM, and Random Forests NeoNet surpassed them. The analysis highlighted the promise of NeoNet in detecting disputed online contents which may contribute negatively to the COVID-19 pandemic.

There is a growing body of evidence supporting the significant role of bacterial biofilms in the pathogenesis of various human diseases including cancer. Biofilms are polymicrobial communities enclosed within an extracellular matrix composed of polysaccharides, proteins, extracellular DNA, and lipids. This complex matrix provides protection against antibiotics and host immune responses, enabling the microorganisms to establish persistent infections. Moreover, biofilms induce anti-inflammatory responses and metabolic changes in the host, further facilitating their survival. Many of these changes are comparable to those observed in cancer cells. This review will cover recent research on the role of bacterial biofilms in carcinogenesis, especially in colorectal (CRC) and gastric cancers, emphasizing the shared physical and chemical characteristics of biofilms and cancer. This review will also discuss the interactions between bacteria and the tumor microenvironment, which can facilitate oncogene expression and cancer progression. This information will provide insight into developing new therapies to identify and treat biofilm-associated cancers, such as utilizing bacteria as delivery vectors, using bacteria to upregulate immune function, or more selectively targeting biofilms and cancer for their shared traits.

Policing duties may inherently be dangerous due to stab, blunt trauma and ballistic threats. The addition of individual light armour vests (ILAVs) has been suggested as a means to protect officers. However, the addition of the extra load of the ILAV may affect officer ability to conduct occupational tasks. The purpose of this study was to determine if wearing any of 3 different ILAVs (ILAV A, ILAV B, & ILAV C) affected occupational task performance when compared to that in normal station wear. A prospective, within-subjects repeated measures design was employed, using a counterbalanced randomization in which each ILAV was worn for an entire day while officers completed a variety of occupationally relevant tasks. These tasks included a victim drag, car exit and 5 meter sprint, step down and marksmanship task. Results showed that performance in each task did not vary between any of the ILAV or normal station wear conditions. There was less variability in the marksmanship task with ILAV B, however. The results suggest that none of the ILAVs used in this study were heavy enough to significantly affect task performance in the assessed tasks when compared to wearing normal station wear.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

E-commerce is a rapidly evolving global trend that is having a significant impact on consumer behavior and business strategies. Despite its growing impact, e-commerce adoption by Moroccan firms remains low and research on this topic in this context is scarce. This study aims to fill this gap by investigating the main determinants influencing e-commerce adoption by Moroccan firms. We use logit, probit, and conditional mixed process-probit models to identify the critical factors driving e-commerce adoption. Our results reveal five key findings. First, newer firms that are more open to innovation and change are more likely to adopt e-commerce. Second, firms with a higher proportion of highly educated employees are more likely to adopt e-commerce. Third, the digital skills of new employees do not directly influence the likelihood of e-commerce adoption. Fourth, being listed on digital platforms increases the likelihood of e-commerce adoption. Finally, there is a positive relationship between firms engaged in innovation activities and e-commerce adoption. These findings highlight the need for additional investment in promoting modern organizational practices, reskilling workers, and implementing advanced technologies to facilitate effective e-commerce integration among Moroccan SMEs. By addressing these challenges, Moroccan firms can harness the full potential of e-commerce and contribute to the country’s economic growth and digital transformation.

Two important types of metal oxide nanoparticle catalysts Copper (II) oxide (CuO) and Cerium oxide (CeO₂) are prepared by a suitable method which was traditional precipitation (PT) method at calcination temperature of 400^oC for 5h and used for the synthesis of glycerol carbonate GC (C₄H₆O₄) from the direct reaction by the carbonylation of Glycerol GL (C₃H₈O₃) with Carbone Dioxide. The precipitation (PT) was an important route for the preparation of nanoparticles catalyst. The effects of performance of (CuO and CeO₂) nanoparticle catalysts on the conversion of glycerol GL, yield of glycerol carbonate GC, selectivity of glycerol carbonate are researched. XRD, XPS, BET, FT-IR, CO₂-TPD, H₂-TPR are used for the characterization of the prepared catalysts. Comparing the optimal performance between them under reaction conditions were 150 ^oC, 4MPa (40 bar.), 5h, and both CuO and CeO₂ catalyst amount 37.6 % (based on ratio of glycerol weight) by using 2-pyridinecarbonitrate (C₆H₄N₂) as dehydrating agent and dimethylformamide (DMF), (C₃H₇NO) as solvent. The glycerol conversion (X_GL), glycerol carbonate yield (Y_GC) and glycerol carbonate selectivity (S_GC) over 0.7g CuO are 57.151%, 47.524%, and 83.156%, respectively, and glycerol carbonate yield over 0.7 CeO₂ is 36.2185% or 35.076%, and the yield of GC could reach as high as 78.234% over 1.73g CeO₂, the both catalysts could be easily regenerated by washing with methanol and water after a reaction and then dried at 60 ^oC overnight after that calcination at 400 ^oC for 5h without loss of activity after five recycling times, In addition to, the (ICP- MS) results confirmed that the leaching of CuO and CeO₂ was below the detection limit.

In response to growing industrial demands, necessitated by larger ships and increased cargo volumes, many port authorities worldwide are undertaking a significant expansion of their infrastructure to increase their capacity. Significant expansion raises challenges such as potential congestion and environmental concerns, especially for port located in urban area as the case study explored in this paper. To address these issues, the study employs a combination of scenario analysis developed in collaboration with the port authority and logistic system simulation. This approach assesses the capacity of existing access gates to handle the increased trucking traffic and optimizes the unloading process of construction trucks at a new terminal. Key findings suggest that while the current gate capacities are adequate, optimizing unloading times at the new terminal is critical to prevent road congestion in urban area before the gate and reduce negative impacts such as sound and atmospheric pollution. The study advocates for an appointment system during peak hours to manage traffic flow effectively and underscores the importance of collaboration between the city and port authorities in managing truck traffic to mitigate congestion on the city side. Nonetheless, the study recognizes certain constraints, including the incomplete evaluation of the influence of intermodal transport on truck traffic. Furthermore, the study emphasizes the need for future research to consider the correlation between vehicle numbers and service levels, aiming to effectively adjust the time in the system.

Abstract: The VSI represents a significant advancement in the assessment of gastrointestinal-specific anxiety among patients with Irritable Bowel Syndrome (IBS) and other Chronic Inflammatory Bowel Diseases (IBD). However, an Italian version of the instrument is not yet available for the reference population. This study utilized a national sample of 500 individuals, including healthy controls and patients with Ulcerative Colitis and Crohn's Disease, to test the validity and reliability of the Italian VSI. Using back-translation methodology to ensure translation fidelity, the research applied a questionnaire and the VSI through an online format to 500 participants. Data analysis revealed that the Italian VSI had excellent psychometric properties, demonstrating high internal consistency (Cronbach’s α = 0.95) and construct validity. The scale proved sensitive in detecting significant differences in visceral sensitivity among groups, highlighting its utility as a clinical and research assessment tool. Specifically, the Italian VSI exhibited a unidimensional factorial structure and maintained a strong correlation with other measures of anxiety and the severity of gastrointestinal symptoms, confirming its role in enhancing the understanding and management of IBS and IBD in Italy.

Fractal analysis of time series aims to extract the hidden or complex structures issued from the associated real data, such as scaling laws, non-stationary, dynamics, and so on. In the present work, the air quality index and its components are considered as time series owing fractal structures. To understand their underlying dynamics, wavelet multifractal approach is applied starting with a wavelet multifractal spectrum test to confirm the multifractality of the underlying data. Next, a new model is introduced improving the classical minmax one, provided with a statistical measure for the adequacy of the new model. The theoretical findings are applied to the north west Tabuk region of Saudi Arabia for environmental and climate data related to pollutants and factors involved in the estimation of the air quality index.

Dictionary Learning (DL) and Sparse Representation (SR) based Classifier have impacted greatly on the classification performance and has had good recognition rate on image data. In Video Semantic Analysis (VSA), the local structure of video data contains more vital discriminative information needed for classification. However, this has not been fully exploited by the current DL based approaches. Besides, similar coding findings are not being realized from video features with the same video category. Based on the issues stated afore, a novel learning algorithm, called Sparsity based Locality-Sensitive Discriminative Dictionary Learning(SLSDDL) for VSA is proposed in this paper. In the proposed algorithm, a discriminant loss function for the category based on sparse coding of the sparse coefficients is introduced into structure of Locality-Sensitive Dictionary Learning (LSDL) algorithm. Finally, the sparse coefficients for the testing video feature sample are solved by the optimized method of SLSDDL and the classification result for video semantic is obtained by minimizing the error between the original and reconstructed samples. The experiment results show that, the proposed SLSDDL significantly improves the performance of video semantic detection compared with the comparative state-of-the-art approaches. Moreover, the robustness to various diverse environments in video is also demonstrated, which proves the universality of the novel approach.

In the realm of the Internet of Things (IoT), a network of sensors and actuators collaborates to fulfill specific tasks. As the demand for IoT networks continues to rise, it becomes crucial to ensure the stability of this technology and adapt it for further expansion. Through an analysis of related works including Feedback-based Optimized Fuzzy Scheduling Approach (FOFSA) algorithm, Adaptive Task Allocation Technique (ATAT) and Osmosis Load Balancing algorithm (OLB), we identify their limitations in achieving optimal energy efficiency and fast decision-making. To address these limitations, this research introduces a novel approach to enhance the processing time and energy efficiency of IoT networks. The proposed approach achieves this by efficiently allocating IoT data resources in the Mist layer during the early stages. We apply the approach to our proposed system known as the Mist-based Fuzzy Healthcare System (MFHS) that demonstrates promising potential to overcome the existing challenges and pave the way for efficient Industrial Internet of Healthcare Things (IIoHT) of the future.

3D printing is commonly used to create complex objects at a low cost. It has also been applied in the fabrication of metamaterials and metasurfaces, which alter the propagation path of electromagnetic waves. These structures have diverse applications, including enhancing beam direction, improving antenna gain and signal-to-noise ratio, and creating filters and reflectors. Metasurfaces are cheap to fabricate and their use is expected to boost antenna efficiency in 5G telecommunications and beyond. However, accurately characterizing their profile remains a significant challenge. This paper presents a low-cost fully automated 4-axis instrument for microwave metasurface charac-terization, overcoming limitations of manual methods and offering an efficient and accurate approach. This research represents a significant advancement in microwave metasurface characterization, enabling sophisticated techniques to advance wireless communication technolo-gies, as it is the case of the future 5G and millimeter-wave communication systems. The equipment has an approximate cost of $1550 USD and was able to characterize a metalens with a focal distance of 20 cm designed for signals at 30 GHz. It was possible to create 2D and 3D profiles of the intensity distribution focused by the metalens and extract parameters such as the gain (8.05 dB), 3dB depth of focus (11 cm) and full width at half maximum (2.17 cm). The comparison of the measurements with the diffraction calculations of the metalens showed a very good agreement between the in-tensity distributions and the parameters of the metalens.

Rapid post-earthquake damage diagnosis of bridges can guide decision-making for emergency response management and recovery. This can be facilitated using digital technologies to remove the barriers of manual post-event inspections. Prior mechanics-based Finite Element (FE) models can be used for post-event response simulation using the measured ground motions at nearby stations; however, the damage assessment outcomes would suffer from uncertainties in structural and soil material properties, input excitations, etc. For instrumented bridges, these uncertainties can be reduced by integrating sensory data with prior models through a model updating approach. This study presents a sequential Bayesian model updating technique, through which a linear/nonlinear FE model, including soil-structure interaction effects, and the foundation input motions are jointly identified from measured acceleration responses. The efficacy of the presented model updating technique is first examined through a numerical verification study. Then, seismic data recorded from the San Rogue Canyon Bridge in California are used for a real-world case study. Comparison between the free-field and the foundation input motions reveals valuable information regarding the soil-structure interaction effects at the bridge site. Moreover, the reasonable agreement between the recorded and estimated bridge responses shows the potentials of the presented model updating technique for real-world applications. The updated FE model is considered as the digital twin of the bridge and can be used to analyze the bridge and monitor the structural response at element, section, and fiber levels to diagnose the location and severity of any potential damage mechanism.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Soil erosion seriously affects vineyards. In this study, the influence of two plant covers on soil moisture and the effect of different physiographic conditions on runoff and sediment yields were evaluated in a rainfed vineyard formed by four fields (NE Spain) during 15 months. One field had spontaneous vegetation as plant cover and three fields had a cover crop of common sainfoin. The vineyards’ rows were dry and stable, whereas the inter-row areas were wet although very variable, and the corridors were wet and very stable. Soil moisture in the inter-row areas with Common sainfoin was much higher than in the rows (62% - 70%) whereas this difference was lower with spontaneous vegetation (40%). Two runoff and sediment traps (STs) were installed in two ephemeral gullies, and 26 time-integrated surveys (TIS) done. The mean and maximum runoff yields were 9.8 and 30.7 l TIS^–1 in ST2 and 13.5 and 30.2 l TIS^–1 in ST3. The mean turbidity was 333 and 19 g l^–1, and the maximum sediment yields were 41,260 and 2,778 g TIS^–1 in ST2 and ST3. Changes in the canopy covers (grapevines and plant covers) and rainfall parameters explained the runoff and sediment dynamics.

This paper provides a structured and practical roadmap for practitioners to integrate Learning from Demonstration (LfD) into manufacturing tasks, with a specific focus on industrial manipulators. Motivated by the paradigm shift from mass production to mass customization, it is crucial to have an easy-to-follow roadmap for practitioners with moderate expertise, to transform existing robotic processes to customizable LfD-based solutions. To realize this transformation, we devise the key questions of "What to Demonstrate", "How to Demonstrate", "How to Learn", and "How to Refine". To follow through these questions, our comprehensive guide offers a questionnaire-style approach, highlighting key steps from problem definition to solution refinement. The paper equips both researchers and industry professionals with actionable insights to deploy LfD-based solutions effectively. By tailoring the refinement criteria to manufacturing settings, the paper addresses related challenges and strategies for enhancing LfD performance in manufacturing contexts.

Zinc finger proteins (ZFP) play important roles in cellular processes. The DNA binding region of ZFP consists of 3 zinc finger DNA binding domains connected by amino acid linkers, the sequence TGQKP connects ZF1 and ZF2, and TGEKP connects ZF2 with ZF3. Linkers act to tune the zinc finger protein in the right position to bind its DNA target, the type of amino acid residues and length of linkers reflect on ZF1-ZF2-ZF3 interactions and contribute to the search and recognition process of ZF protein to its DNA target. Linker mutations and the affinity of the resulting mutants to specific and nonspecific DNA targets were studied by MD simulations and MM_GB(PB)SA. The affinity of mutants to DNA varied with type and position of amino acid residue. Mutation of K in TGQKP resulted in loss in affinity due to the loss of positive K interaction with phosphates, mutation of G showed loss in affinity to DNA, WT protein and all linker mutants showed loss in affinity to a nonspecific DNA target, this finding confirms previous reports which interpreted this loss in affinity as due to ZF1 having an anchoring role, and ZF3 playing an explorer role in the binding mechanism. The change in ZFP-DNA affinity with linker mutations is discussed in view of protein structure and role of linker residues in binding.

Dietary factors are one of the risk factors that can impact the brain chemistry, which leads to mental distress. Based on our data mining approach, we found that mental distress in men is associated with eating unhealthy food. Our aim in this paper is to apply results from our big data analytics approach to inform system dynamics (SD) modeling to investigate the causal relationships between brain structures, nutrients from food and dietary supplements, and mental health. We perform descriptive analysis based on a large data set to estimate the SD modeling parameters. Finally, we calibrate the model towards a time series data collected for individuals on their dietary and distress patterns. The results reveal that bridging these different methodologies leads to further insights from the SD model and decreases the error of calibrated parameter values. Future research is needed to validate our initial results for investigating the relationship between mental distress and dietary intake.

All living cells maintain a charge distribution across their cell membrane (membrane potential) by carefully controlled ion fluxes. These bioelectric signals regulate cell behavior (such as migration, proliferation, differentiation) as well as higher-level tissue and organ patterning. Thus, voltage gradients represent an important parameter for diagnostics as well as a promising target for therapeutic interventions in birth defects, injury, and cancer. However, despite much progress in cell and molecular biology, little is known about bioelectric states in human stem cells. Here, we present simple methods to simultaneously track ion dynamics, membrane voltage, cell morphology, and cell activity (pH and ROS), using fluorescent reporter dyes in living human neurons derived from induced neural stem cells (hiNSC). We developed and tested functional protocols for manipulating ion fluxes, membrane potential, and cell activity, and tracking neural responses to wounding and re-innervation in vitro. Finally, using morphology sensor, we tested and quantified the ability of physiological actuators (neurotransmitters and pH) to manipulate nerve wound re-innervation. These methods are not specific to a particular cell type and should be broadly applicable to the study of bioelectrical controls across a wide range of combinations of models and endpoints.

model checking techniques are often used for the verification of software systems. Such techniques are accompanied with several advantages. However, state space explosion is one of the drawbacks to model checking. During recent years, several methods have been proposed based on evolutionary and meta-heuristic algorithms to solve this problem. In this paper, a hybrid approach is presented to cope with the SSE problem in model checking of systems modeled by GTS with an ample state space. Most of existence proposed methods that aim to verify systems are applied to detect deadlocks by graph transformations. The proposed approach is based on the fuzzy genetic algorithm and is designed to decline the safety property by verifying the reachability property and detecting deadlocks. In this solution, the state space of the system is searched by a fuzzy genetic algorithm to find the state in which the specified property is refuted/verified. To implement and evaluate the suggested approach, GROOVE is used as a powerful designing and model checking toolset in GTS. The experimental results indicate that the presented hybrid fuzzy method improves speed and performance by comparing other techniques

Polymer electrolyte was used as a medium for testing the performance of microband electrodes under conditions of linear diffusion. Cyclic voltammetry and chronoamperometry experiments were performed in such viscous medium, where diffusion rates are much slower than in fluid solutions. Confirmation of the existence of such conditions from the log i vs. log v or log i vs. log t relationships in the current equation always yielded values lower than the expected value of 0.5. This could indicate impure linear diffusion profile, i. e. some contribution from radial diffusion (edge effect). However, performing these tests in monomeric solvents of similar viscosities, such as glycerol or propylene glycol, gave the desired value of 0.5. These results lead to the conclusion that current equations which are based on Fick’s laws may not be applicable for polymer electrolytes, where various obstruction to diffusion make it a more complicated process than in monomeric solvents.

This paper presents a novel method for automatic modulation classification (AMC) for cognitive radio (CR) networks based on a simple classifier that is trained with high-order cumulant. The proposed method focuses on the statistical behavior of modulated signals and includes analog modulation and digital schemes, which received less attention in the literature. The effectiveness of the proposed method is demonstrated through simulation results using high-quality generated signals under different signal-to-noise ratios (SNRs) and channel conditions. The classification performance achieved by the proposed method is superior to that of the more complex deep learning methods, making it well-suited for deployment in end units of CR networks, particularly in military and emergency service applications. The proposed method offers a cost-effective, high-quality solution for AMC that meets the stringent requirements of these critical applications.

Recently we have seen a relaxation of the historic restrictions on the use and subsequent research on the Cannabis plants, generally classified as Cannabis sativa and Cannabis indica. What research has been performed to date has centered on chemical analysis of plant flower products, namely cannabinoids and various terpenes that directly contribute to phenotypic characteristics of the female flowers. In addition, we have seen many groups recently completing genetic profiles of various plants of commercial value. To date, no comprehensive attempt has been made to profile the proteomes of these plants. We report herein our progress on constructing a comprehensive draft map of the Cannabis proteome. To date we have identified over 17,000 potential protein sequences. Unfortunately, no annotated genome of Cannabis plants currently exists. We present a method by which “next generation” DNA sequencing output and shotgun proteomics data can be combined to produce annotated FASTA files, bypassing the need for annotated genetic information altogether in traditional proteomics workflows. The resulting material represents the first comprehensive annotated protein FASTA for any Cannabis plant. Using this annotated database as reference we can refine our protein identifications, resulting in the confident identification of 13,000 proteins with putative function. Furthermore, we demonstrate that post-translational modifications play an important role in the proteomes of Cannabis flower, particularly lysine acetylation and protein glycosylation. To facilitate the evolution of analytical investigations into these plant materials, we have created a portal to host resources we have developed from proteomic and metabolomic analysis of Cannabis plant material as well as our results integrating these resources. All data for this project is available to view or download at www.CannabisDraftMap.Org

Several factors influence traffic congestion and overall traffic dynamics. Simulation modeling has been utilized to understand the traffic performance parameters during traffic congestions. This paper focuses on driver behavior of route selection by differentiating three distinguishable decisions, which are shortest distance routing, shortest time routing and less crowded road routing. This research generated 864 different scenarios to capture various traffic dynamics under collective driving behavior of route selection. Factors such as vehicle arrival rate, behaviors at system boundary and traffic light phasing were considered. The simulation results revealed that shortest time routing scenario offered the best solution considering all forms of interactions among the factors. Overall, this routing behavior reduces traffic wait time and total time (by 69.5% and 65.72%) compared to shortest distance routing.

Background: The genetic variants identified by three large genome-wide association studies (GWAS) of educational attainment were used to test a polygenic selection model. Methods: Average frequencies of alleles with positive effect (polygenic scores or PS) were compared across populations (N=26) using data from 1000 Genomes. A null model was created using frequencies of random SNPs. Results: Polygenic selection signal of educational attainment GWAS hits is high among a handful of SNPs within genomic regions replicated across GWAS publications. A polygenic score comprising 9 SNPs predicts population IQ (r=0.88), outperforming 99% of the polygenic scores obtained from sets of random SNPs (Monte Carlo p= 0.011). Its predictive power remains unaffected after controlling for spatial autocorrelation (Beta= 0.83). The largest polygenic score (161 SNPs) exhibits similar predictive power (Beta=0.8). Random polygenic scores are moderate predictors of population IQ (thanks to spatial autocorrelation), and their predictive power increases logarithmically with the number of SNPs, indicating an exponential reduction in noise. Conclusion: This study provides guidance for using GWAS hits together with random SNPs for testing polygenic selection using Monte Carlo simulations.

By studying game theory, we find that the Nash equilibrium does not exist in some games or, if there is in one, does not describe a real event. Here we show that the matching pennies game with pure strategy has the solution, but this solution is a game that happens simultaneously with this game. Using this solution, we will answer the Brookings Institution's question of boycotting the elections whether the opposition's boycott of elections is, in different circumstances, a defeated strategy. A strategy that its result in most cases is a failure or political suicide and the least possible consequence by the opposition. The findings of this article show that in general, it can be concluded that the election boycott strategy is a dominated strategy, and most of the opposition groups that have used it have failed and they donated the playground to the ruling group.

Marfan syndrome is an autosomal dominant genetic connective tissue disorder that results from mutations in the fibrillin-1 gene located on chromosome band 15q 15–21. Fibrillin, a glycoprotein, is widely expressed throughout the body and contribute to elasticity and force-bearing capacity of connective tissue. In the eye, fibrillin is a key constituent of the ciliary zonules, which suspend the crystalline lens in place. The zonular defect leads to ectopia lentis that is hallmark of Marfan ocular abnormalities and occurs in 60 to 80% of cases. Other less common ocular features of Marfan syndrome are increased axial length, astigmatism, and flat cornea. Visual function in Marfan syndrome could be affected in several ways: ectopia lentis, refractive error, amblyopia, retinal detachment, cataract, and glaucoma. Management of subluxated lens starts with correction of refractive error with eyeglasses in mild cases. In more severe cases, especially when lens bisects the pupil, complete correction of refractive error is impossible without removing subluxated lens. The best method for visual rehabilitation after lens extraction is still debated. Aphakic Artisan implantation at the time of subluxated lens removal results in good visual outcomes with acceptable safety profile. Studies with longer term follow up and larger sample populations are needed to evaluate the safety of this procedure in patients with Marfan syndrome.

Cancer is one of the leading causes of death, making timely diagnosis and prognosis very important. Utilization of AI (artificial intelligence) enables providers to organize and process patient data in a way that can lead to better overall outcomes. This review paper aims to look at the varying uses of AI for diagnosis and prognosis and clinical utility. PubMed and EBSCO databases were utilized for finding publications from January 1, 2013, to December 22, 2023. Articles were collected using key search terms such as “artificial intelligence” and “machine learning.” Included in the collection were studies of the application of AI in determining cancer diagnosis and prognosis using multi-omics data, radiomics, pathomics, clinical and laboratory data. The resulting 89 studies were categorized into eight sections based on the type of data utilized and then further subdivided into two subsections focusing on cancer diagnosis and prognosis, respectively. 8 studies integrated more than one form of omics, namely genomics, transcriptomics, epigenomics, and proteomics. Incorporating AI into cancer diagnosis and prognosis alongside omics and clinical data represents a significant advancement. Given the considerable potential of AI in this domain, ongoing prospective studies are essential to enhance algorithm interpretability and to ensure safe clinical integration.

Purpose: To compare the therapeutic efficacy and safety of dorzolamide/timolol fixed-combination in newly diagnosed primary open angle glaucoma patients. Methods: In this prospective, interventional case series, newly diagnosed primary open angle glaucoma (POAG) patients that had not been treated for glaucoma were included. Patients were started on Cosopt twice a day (BID) for 1 month and then switched to three times a day (TDS) for additional 1 month. Patients underwent comprehensive ophthalmic examination, diurnal intraocular pressure (IOP), blood pressure (BP) and 24-hours heart rate (HR) measurements at baseline, month 1( BID), and month 2( TDS). IOP, systolic and diastolic pressures were measured at 8:00 AM,12:00 AM, 4:00 PM, 8:00 PM and 12:00 PM. Throughout the study, all adverse events were recorded and monitored by the investigators. Results: In 31 POAG patients that completed the study ,mean baseline IOP was 23.1±3.15 mmHg . IOP was decreased significantly 16.5 ± 2.21 at 1 month (P < 0.0001) and 13.9 ± 2.23 mmHg at 1 and 2 month follow up. (P < 0.0001) IOP was significantly lower in month 2 compared to month 1 (P = 0.0004). While Cosopt BID significantly reduced the mean 24-hour systolic BP and mean 24-hour HR from baseline (P < 0.0001), the mean 24-hour systolic BP and HR remained unchanged 2ith Cosopt TDS compared to BID (P = 0.62). Conclusions: Cosopt TDS has a superior IOP-lowering effect than Cosopt BID in POAG patients with comparable safety profile.

The Capital Asset Pricing Model is a widely applied model to describe risky markets and to deduce their systematic risk. Its estimation, therefore, remains an important task in Econo-financial studies. Empirically, it focuses on the impact of return interval on the betas. Existing studies somehow turn around the same idea of measuring the value of the beta according to the uniform intervals of time during a fixed period. However, it is noticed easily, and especially in the last decade that many factors such as socio-political, and Econo-environmental ones have led to a perturbation in the timeline of the worldwide development, and especially in countries and regions having political changes. This led us to introduce a new idea of risk estimation taking into account the non-uniform changes in markets by introducing a non-uniform wavelet analysis. We aim to explain the Econo-political situation of Arab spring countries and the effect of the revolutions on the market beta. The main novelty is firstly the construction of a dynamic backward-forward model for missing data, and next the application of random non-uniform wavelets. The proposed procedure will be acted empirically on a sample corresponding to TUNINDEX stock as a representative index of the Tunisian market actively traded over the period January 14, 2016, to January 13, 2021. The chosen 5-years period is important as it constitutes the first 5-years-after the revolution and depends strongly on the Socio-Econo-political stability in the revolutionary countries.

In this paper, a model of the hub covering the location-routing problem with simultaneous delivery and pickup should be designed in order to minimize the total costs, minimize the maximum vehicles travel time and minimize the amount of CO_2 gas emissions. Two-stage stochastic programming is used in this paper to control the uncertainty parameters of the problem. The mathematical model aims to decide the appropriate location of hubs and vehicle routing for simultaneous delivery and pickup of products. In this regard, the results obtained from the LP-Metric method show that there is a conflict between the objective functions, and with the reduction of the amount of CO_2 gas emissions and the reduction of the maximum vehicles travel time, the total costs have increased. On the other hand, by examining the economical factor, it was observed that by reducing this factor, the robustness factors are changed and the total costs of the network are reduced. MOIWO and MOALO were used to solve the problem in large scale, the result of which was the existence of a significant difference between the calculation time averages. Also, the efficiency of these methods was very high compared to the LP-Metric method and the maximum relative difference was less than 2.83%. The results of numerical examples show a higher efficiency of the MOALO than the MOIWO.

Responsible, efficient, and environmentally conscious energy consumption practices are increasingly essential for ensuring the reliability of the modern electricity grid. This study focuses on leveraging time series analysis to improve forecasting accuracy, crucial for various application domains where real-world time series data often exhibit complex, non-linear patterns. Our approach advocates for utilizing Long Short Term Memory (LSTM) and Bidirectional LSTM (BiLSTM) models for precise time series forecasting. To ensure a fair evaluation, we compare the performance of our proposed approach with traditional neural networks, time-series forecasting methods, and conventional decline curves. Additionally, individual models based on LSTM, Bi-LSTM, and other machine learning methods are implemented for a comprehensive assessment. Experimental results consistently demonstrate that our proposed model outperforms all benchmarking methods in terms of mean absolute error (MAE) across most datasets. Addressing the imbalance between activations by consumer and prosumer groups, our predictions show superior performance compared to several traditional forecasting methods, such as the Autoregressive Integrated Moving Average model (ARIMA) and Seasonal Autoregressive Integrated Moving Average model (SARIMA). Specifically, the root mean square error (RMSE) of Bi-LSTM is 5.35%, 46.08%, and 50.6% lower than LSTM, ARIMA, and SARIMA, respectively, on the May test data.

Streptococcus mutans is a key bacterium in dental caries- one of the most prevalent chronic infectious diseases. Conventional treatment both fails to specifically target the pathogenic bacteria and at-tempts to eradicate commensal bacteria as well. Thus, caries remains one of most common and challenging diseases. The use of bacterial viruses as anti-bacterial agents, is gaining interest worldwide. Hardly any phages were described against S. mutans. The objective of this study was to isolate anti-S. mutans phages and to characterize their antimi-crobial properties. Human saliva samples were filtered and screened for potential phages. Standard double-layered agar method was used for isolation. Whole genome sequence analysis and morphology visualization by TEM, were used for anti-S. mutans phage identification. Antibacterial properties were evaluated using clinical strains and ATCC strains of S. mutans in various states. Antibacterial effect was also tested on human cariogenic dentin. One phage against S. mutans was isolated and termed SMHBZ8. This phage showed effective lytic activity in vitro against both planktonic and biofilm S. mutans cultures. Moreover, the phage showed antibacterial effect when used on cariogenic dentin. The isolation and characterization of SMHBZ8 may be the first step in developing a potential phage therapy for dental caries.

Ocular drug delivery is one of the most challenging administration routes due to the very low drug bioavailability. In this work, we produce and characterize mucoadhesive mixed polymeric micelles (PMs) made of chitosan and poly(vinyl alcohol) backbones graft-hydrophobized with short poly(methyl methacrylate) blocks and use them to encapsulate cannabidiol (CBD), an anti-inflammatory cannabinoid. CBD-loaded mixed PMs are physically stabilized by ionotropic crosslinking of the CS domains with sodium tripolyphoshate and spray-drying. These mixed PMs display CBD loading capacity of 20% w/w and sizes of 100-200 nm, and spherical morphology (cryogenic-transmission electron microscopy). The good compatibility of the unloaded and CBD-loaded PMs is assessed in a human corneal epithelial cell line. Then, we confirm the permeability of CBD-free PMs and nanoencapsulated CBD in cornea cell monolayers under liquid-liquid and air-liquid conditions. Overall, our results highlight the potential of these polymeric nanocarriers for ocular drug delivery.

This paper presents a new method for approximating the classical arcsine function. The proposed approximating methodology is simpler in its approach than other classical approaches and undeniably innovative. It is based on matrix representation besides the basic interpolation to approximate the inverse trigonometric function. It provides an efficient model which allows for reliable and precise calculations. The results are as per our knowledge unseen results in the previous literature.

The present paper is concerned with the study of the quality of life index. Such an index has become an important index for measuring the well-being of individuals. However, the quality of life index is always a subjective, intangible, and often hard to quantify with precision due to the lack of quantitative models dealing with. The main goal of the present paper is thus to propose a mathematical, quantitative model for the measurement of a quality of life index. The main novelty is firstly the construction of a wavelet dynamic multiscale model to quantify and investigate the effect of time scale on the quality of life index measuring. The proposed procedure is acted empirically on a sample corresponding to Saudi Arabia as a case of study during the period from 2003 to 2020 as part of the 2030-vision plan. Saudi Arabia has implemented the so-called 2030-vision plan where the quality of life improvement is one of the main goals to be attempted. The findings show that wavelets are capable to localize the time-wise behavior of the index contrarily to classical studies which estimate a global view of the index. Moreover, the study shows the link between the quality of life behavior and many other indices.

The relative operating characteristic (ROC) curve is a popular diagnostic tool in forecast verification, with the area under the ROC curve (AUC) used as a verification metric measuring the discrimination ability of a forecast. Along with calibration, discrimination is deemed as a fundamental probabilistic forecast attribute. In particular, in ensemble forecast verification, AUC provides a basis for the comparison of potential predictive skill of competing forecasts. While this approach is straightforward when dealing with forecasts of common events (e.g. probability of precipitation), the AUC interpretation can turn out to be oversimplistic or misleading when focusing on rare events (e.g. precipitation exceeding some warning criterion). How should we interpret AUC of ensemble forecasts when focusing on rare events? How can changes in the way probability forecasts are derived from the ensemble forecast affect AUC results? How can we detect a genuine improvement in terms of predictive skill? Based on verification experiments, a critical eye is cast on the AUC interpretation to answer these questions. As well as the traditional trapezoidal approximation and the well-known bi-normal fitting model, we discuss a new approach which embraces the concept of imprecise probabilities and relies on the subdivision of the lowest ensemble probability category.

Recent years have seen dramatic growth in the number of scholarly scientific works dedicated to the topic of Artificial Intelligence (AI), banking, and finance. With the development of scientometric tools, it is now possible to map, visualize, analyze, and assess scientific activities in many fields of engineering and social sciences including Islamic banking and finance. Based on data retrieved from the Scopus database and using a qualitative method, this study investigates, evaluates, and identifies significant development, trends, and players in the application of AI in Islamic banking and finance using the Visualization Of Similarities Method (VOS) between objects in VOSviewer. From 2006 to 2022, 387 documents were retrieved from the Scopus database; Results revealed that the top five most active countries in terms of publications are Malaysia (117 documents), Indonesia (89 documents), the United Kingdom (36 documents), the USA (24 documents), and Saudi Arabia and Bahrain (24 documents each). The International Islamic University Malaysia and Universitas Indonesia came out on top of active institutions while the top funding source came from the Ministry of Higher Education, Malaysia. The comprehensive findings and analysis reported in this study serve as a roadmap for future academics to create theory and practice for applying AI in Islamic banking and finance.

Glucosamine is the most common nutrition supplement used in the United States. It is promoted not only as a pain reliever but also a therapy to slow osteoarthritis. Although studies with 3,800 patients with osteoarthritis of the knee or hip found that glucosamine was no better than placebo, it continues to be used for these two indications due to its perceived safety. However, reports of an increased intraocular pressure are alarming, especially in glaucoma. Glycosaminoglycans play a key role in the physiology of the cornea, conventional outflow of aqueous humor and the retina. In theory, long-term treatment with glucosamine could reach a concentration that impacts the morphology and function of ocular tissues. We recommend ophthalmologists counsel glaucoma patients about the potential risks of glucosamine and encourage cessation in uncontrolled intraocular pressure.

Sulfated polysaccharides from seaweed are highly active natural substances having valuable applications. In the present paper, attempts have been made to discuss the physicochemical and structural features of polysaccharides isolated from red marine alga Alsidium corallinum (ACPs) and its protective effect in hepatic impairments induced by tebuconazole (TBZ) in rats. Structural features were determined using High performance liquid chromatography, Fourier transformed infrared, and solid state ¹H and ¹³C-Nuclear magnetic resonance analysis. ACPs are found to be hetero-sulfated-anionic polysaccharides that contained carbohydrates, sulfate groups and uronic acids. In vitro biological activities suggested the effective antioxidant and antimicrobial capacities of ACPs. For antioxidant testing in vivo, the biochemical analysis and plasma profiles displayed that oral administration of ACPs could mitigate blood lipid indicators, including total cholesterol, triglyceride, low and high density lipoprotein cholesterol, bilirubin, liver function indexes involving alanine aminotransferase and aspartate aminotransferase, showed that ACPs possessed obvious antioxidant activities. Besides, the intervention of ACPs potentially inhibited lipid peroxidation, protein oxidation, key enzymes of lipid metabolism (<0.001) and increased levels and antioxidant status (<0.05). Histomorphological observation confirmed that ACPs intervention could partially repair liver injuries caused by TBZ. The computational results showed that A. corallinum monosaccharides bound 1JIJ, 1HD2 and 1WL4 receptors with acceptable affinities, which together with deep embedding and molecular interactions support the antioxidant, antimicrobial and hypolipidemic outlined effects in the in vitro and in vivo findings. In view of their prominent antioxidant effects, ACPs stand for promising candidates in liver diseases and need be considered in pharmaceutical applications.

The realization of a BRST cohomology of the 4D topological gauge-affine gravity is established in terms of a superconnection formalism. Identification of fields in the quantized theory is occurred directly as usual in terms of superconnection and its supercurvature components with the double covering of the general affine group GA¯(4,R). Then, by means of an appropriate decomposition of the metalinear double-covering group SL¯(5,R) with respect to the general linear double-covering group GL¯(4,R) one can easily obtain the enlargements of the fields while remaining consistent with the BRST algebra. This leads to the descent equations allowing us to build the observables of the theory by means of the BRST algebra constructed using a sa¯(5,R) algebra-valued superconnection. In particular, we discuss the construction of topological invariants with torsion.

Climate change has become a major agenda item in international relations and in national energy policy-making circles around the world. This article studies the surprising evolution of the energy policy, and more particularly the energy transition, currently happening in the Arabian Gulf region, which features some of the world’s largest exporters of oil and gas. Qatar, Saudi Arabia and other neighboring energy exporters, plan to export blue and green hydrogen across Asia as well as towards Europe in the years and decades to come. Although poorly known and understood abroad, this recent strategy doesn’t threaten the current exports of oil and gas (still needed for a few decades) but prepares the evolution of their national energy industries towards the future decarbonized energy demand of their main customers in East and South Asia, and beyond. The world’s largest exporters of Liquefied Natural Gas, Qatar, has established industrial policies and projects to upscale CCUS, which can enable blue hydrogen production, as well as natural carbon sinks domestically via afforestation projects.

This study presents the consecutive modification of orange peel (OP) by NaOH and sodium dodecyl sulfate (SDS) for simultaneous elimination of basic dyes from the binary system and modeling the adsorption process using an intelligent tool. The natural and modified biosorbents were characterized by variety of analyses such as: field emission scanning electron microscopy with energy dispersive X-ray, N2 physisorption and Fourier transform infrared spectroscopy techniques. The influence of various variables on dye removal like pH, the quantity of biosorbents, dyes concentration, contact time, and temperature in the binary system were investigated and optimized by an artificial neural network (ANN) model as an intelligent tool. The optimum quantity of the sorbent was found to be 0.30 g for orange peel (OP) and 0.25 g for NaOH-treated OP (NOP) and SDS-decorated NOP (SNOP) at pH = 7. The kinetics and thermodynamics investigations showed that the removal of dyes obeyed the pseudo-second-order kinetic model and were spontaneous and exothermic in nature. Moreover, in order to describe the mechanism of sorption process, desorption studies of dyes were carried out. The desorption percentages of methylene blue (MB) in water and HCl were found to be in the range of 1.93%–4.76% and 18.87%–28.76%, respectively; in addition, the desorption percentages of crystal violet (CV) in water and HCl were obtained to be in the range of 4.11%–7.41% and 32.84%–43.00%, respectively; which could be a recommendation ion exchange or electrostatic attachment of dyes onto biosorbents. The ANN predictions matched with the experimental data very well (0.95308 < R2 < 0.99191 and 0.98335 < R2 < 0.99773 for MB and CV, respectively) which indicated high accuracy of the ANN model. In addition, the relative importance of each parameter was calculated by Garson’s equation.

We seek to examine effective collaboration when engaging in value cocreation with the customer for mobile financial services in EMs. Our study is a motivation for multi-stakeholder engagement in value cocreation with financial inclusion of all consumers including marginalized populations. Furthermore, our work discovers that social sustainability is a product of social creativity and results in financial inclusion. We apply a qualitative descriptive methodology utilizing exemplars from extant research and phenomenology to analyze the data from the contexts of Ghana and Kenya. The results show that value is co-created for mobile financial services in networks in emerging markets when actors integrate resources for social and environmental sustainability as essential elements for mobile financial inclusion.

Helicobacter pylori is the most common human gastric infection. H. pylori stool antigen lateral flow immunochromatography assay (HpSA-LFIA) is considered one of the most cost-effective and rapid non-invasive assays (active tests). The evaluation of this test is crucial for accuracy and utility assurance. This study aimed to evaluate the polyclonal antibody-based HpSA-LFIA in comparison to a monoclonal antibody-based ELISA kit. Methodology: Stool samples were collected from 200 gastric patients for HpSA-LFIA and semi-quantitative HpSA-ELISA. Statistical analysis of the diagnostic values was performed using MedCalc software. Chi-square tests were used to determine the effects of gender and age. Results: The obtained results found that HpSA-LFIA achieved promising sensitivity (93.75%) and NPV (98.00%). However, it had poor specificity, PPV, and accuracy, respectively, 59.76%, 31.25%, and 65.31%. LR+ & LR- were 2.33% & 0.1%, respectively. Gender had no significance on the di-agnostic parameters of HpSA-LFIA. Age groups had irrelevant sensitivity; however, specificity was significantly higher in patients over 45 years. Conclusion: It was concluded that HpSA-LFIA was not accurate enough to be the sole test for di-agnosis and needs other confirmatory tests in case of positive conditions

In arid and semi-arid regions like Tunisia, irrigation water is typically saline, posing a soil and crop salinization risk and yield reduction. This research aims to study the combined effects of soil matric and osmotic potential stresses on tomato root water uptake. Plants were grown in pot and field experiments in loamy-clay soils and were irrigated with three different irrigation water qualities: 0, 3.5, and 7 dS/m. The Hydrus-1D model was used to simulate the combined dynamics of subsurface soil water and salts. Successful calibration and validation of the model against measured water and salt profiles enabled the examination of the combined effects of osmotic and matric potential stresses on root water uptake. Relative yields, indirectly estimated from actual and potential transpiration, indicated that the multiplicative stress response model effectively simulated measured yields and the impact of saline water irrigation on crop yields. The gradual salinization of the root zone further evidenced this effect. The scenario considering a temperature increase of 2°C had no significant impact on crop yields in the pot and field experiments.

Background: Studies have demonstrated the link between vitamin D-related genetic variations and non-skeletal outcomes. We aimed to identify all available data on the association of vitamin D-related genetic variations with non-alcoholic fatty liver disease (NAFLD). Methods: Potentially eligible studies were identified from Embase and Medline databases from inception to June 2022 using search strategy that comprised terms for “Vitamin D” and “NAFLD”. Eligible study must report the association between vitamin D-related genetic variations and presence, severity or response to treatment of NAFLD. Data were extracted from each eligible study. Results: A total of 3,495 articles were identified. After systematic review, twelve studies were in-cluded. A total of 26 genetic variations were identified. Presence of NAFLD was associated with variations of GC (rs222054, rs222020, rs10011000, rs7041), VDR (rs2228570, rs11168287, rs10783219, rs4752), CYP24A1 (rs3787557, rs6068816, rs2296241, rs2248359) and CYP27B1 (rs4646536). Severity of NAFLD was associated with variations of GC (rs4588), VDR (rs2228570, rs4334089), CYP2R1 (rs10741657), DHCR7 (rs1544410, rs3829251, rs12785878) and CYP24A1 (rs3787557, rs6068816, rs6097809, rs6127119, rs2248359, rs3787554, rs4809960, rs6022999). Response to calcitriol treatment was associated with variation of VDR (rs10735810). Conclusions: Multiple vitamin D-related genetic variations were associated with NAFLD, indi-cating the role of vitamin D in the pathogenesis of NAFLD.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

Natural gas plays a significant role in Tunisia's energy mix. Tunisia imports 66% of natural gas (NG) from Algeria (ANG), and the rest is provided by local gas fields mainly Miskar gas (MNG). To counteract this deficit, the Power-to-Gas approach emerges as a promising solution, given Tunisia's abundant renewable energy resources. By blending green hydrogen into the NG network, it is possible to (i) address the current energy crisis, (ii) lower the carbon intensity of the gas grid, and (iii) encourage sector coupling through the use of various renewable energy sources. This study presents an overview of various interchangeability indicators and investigates accordingly the allowable ratios for hydrogen blending with two types of natural gas distributed in Tunisia (ANG and MNG). It also explores the impact of hydrogen injection on the energy content variation and various combustion parameters. The results confirm that both ANG and MNG can withstand a maximum hydrogen blend of up to 20%. The article concludes with recommendations for further experimental testing of the findings and emphasizes the need to look into infrastructure and safety requirements with regards to the Natural gas network in Tunisia. This research serves as a critical step towards harnessing the potential of green hydrogen in Tunisia.

The shoulder region has the highest incidence of acute injuries in the sport of surfing. Little is known about the strength profile at the shoulder in a surfing cohort. The primary aim of this study was to establish the reliability of a rotator cuff strength testing procedure for surfers with a secondary aim of providing a profile of internal (IR) and external rotation (ER) strength in a competitive surfing cohort. Shoulder IR and ER isometric strength was measured using a hand-held dynamometer in 13 competitive surfers. Intra-class coefficient values ranged from 0.97 to 0.98 for intra rater reliability and were lower for inter rater reliability ranging from 0.80 to 0.91. Normalised force (N/Kg) for IR strength was significantly greater than ER strength bilaterally (dominant, p= 0.007, non-dominant, p<0.001). No significant differences (p< 0.79) were found in IR strength (N/Kg) between the dominant and non-dominant arms. ER strength (N/Kg) was significantly weaker on the non-dominant arm compared with the dominant arm (p<0.02). The non-dominant arm ER to IR ratio (0.82 ± 0.15) was significantly (p=0.025) lower than the dominant (0.88 ± 0.14) The current procedure is reliable with the same clinician, results indicate musculature asymmetry specific to the external rotators.

Air quality and environmental fairness have always been an area of prime interest across the globe. The significance low-cost air quality sensing and practices spikes during the time of pan-demic and epidemics when the air becomes a threat to living beings especially human beings. The gradual innovation and enrichment in low-cost air quality sensing sensors, nodes or devices, and systems are exponentially increasing for the last three decades. This work reviews the major contributions in a) low-cost scalable air quality assessment; b) low-cost air quality sensors, sensing approaches and technologies; c) low-cost state-of-the-art gas sensors fabrication methods (MEMS and CMOS); d) low-cost gas sensors measurement configurations and assemblies; and e) low-cost air quality sensors calibration and testing systems. A systematic review of past work with a goal to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies has been rendered in this work. Starting from sensors electrodes to IoT based mobile smart nodes; all have been introduced in this article.

Since 2012, the northeast of Tunisia has been experiencing an emergence of dog rabies. Published data revealed that the disease is widespread in the north of Tunisia. Even with studies on rabies, lacking knowledge on the associated risk factors was highlighted. Therefore, we conducted a case-control study on dog rabies in northeast Tunisia to identify potential risk factors for dog rabies occurrence. The cases group (n=77) included positive dog rabies confirmed at the referral laboratory using Fluorescent Antibody Test (FAT) in 2014 and 2018. The controls group (n=77) involved all negative cases received at the laboratory and 15-days quarantine dogs that received a certificate of absence of rabies after the observation period. Univariate and multivariate logistic regression was conducted to explore the risk factors (age, sex, breed, confinement, vaccination status, presence of bites, owned or not and origin of dogs, sector, presence of rabies cases, and slaughterhouses, etc.…) related to the occurrence of rabies. The final logistic regression model revealed that unconfined dogs were almost twice as likely to be affected as confined dogs (OR=1.9; 95% CI: 1.17 to 3.27). The odds of rabies occurrence were 25 times higher in areas where rabies cases have been reported between 3 months and 1 year compared to the uninfected areas (25.7; 95% CI: 3.02-219.14). Similarly, the risk of rabies is significantly higher in dogs born in the home to the owner bitch (OR=2.41; 95% CI: 1.14-5.13). Living in areas with rabies cases in the last three months increases by 2.8 times the risk of getting rabies (2.8; 95% CI: 1.16-6.77). However, vaccination reduces by 1.6 times the risk of contracting rabies (0.6; 95% CI: 0.38-0.97). Our findings provide reliable data on dog rabies that will be very useful for decision-makers and could contribute to improving the ongoing national control program of rabies.