The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

Vector geographic data play an important role in the natural resources and environment sector and other location information services. This is also one of the types of data where the cost to create it is relatively large because of the difficulty in surveying, collecting, and authorizing. The rapid development of the Internet has created many advantages in the distribution, exploitation, and use of vector geographic data, but it also gives rise to many problems such as duplication, redistribution, forgery, and illegal data use. The theft on the Internet is becoming more and more sophisticated and the number of violations is increasing, showing the urgent need to research and develop an effective solution to protect the copyright of vector geographic data and prevent them from being illegally collected and used. Among the major studies and solutions, digital watermarking emerges as an effective method and is an active research area for copyright protection. Towards a good solution for copyright protection of vector geographic data, our study proposes a new algorithm with three main contributions, including: (1) generating short, pseudo-random meaningful watermarks to increase robustness and to enable automated as well as visual manual verifying; (2) building a uniformly distributed mapping between the vertex coordinates and the watermark bit indexes to increase the robustness of the watermarks; and (3) integrate two types of watermarks, namely, spatial domain-based watermarking and zero-watermarking to be resistant to most common attacks on geographic vector data. The algorithm also allows working on all types of vector geographic data, including points, polylines, and polygons.

With Internet of Things (IoT) gaining presence throughout different industries a lot of new technologies have been introduced to support this undertaking. Implications on one such technology, wireless systems allowed for the use of different communication methods to achieve the goal of transferring data reliably, with more cost efficiency and over longer distances. Anywhere from a single house with only a few IoT devices such as a smart light bulb or a smart thermostat connected to the network, all the way to a complex system that can control power grids throughout countries, IoT has been becoming a necessity in everyday lives. This paper presents an overview of the devices, systems and wireless technologies used in different IoT architectures (Healthcare, Vehicular Networks, Mining, Learning, Energy, Smart Cities, Behaviors and Decision Making), their upbringings and challenges to this date and some foreseen in the future.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

Flood frequency analysis at large scales, essential for the development of flood risk maps, is hindered by the uncertainty in outputs of process-based hydrological models and the scarcity of gauge flow data. We develop a Bayesian hierarchical model (BHM) based on the Generalized Extreme Value (GEV) distribution for regional flood frequency analysis at high resolution across North America. Our model leverages annual maximum flow data from ≈20000 gauged stations and a dataset of 130 static catchment-specific covariates to predict extreme flows at all catchments over the continent as well as their associated statistical uncertainty. Additionally, a modification is made to the data layer of the BHM to include daily gauge discharge data when available, which improves the precision of the discharge level estimates. We validated the model using a hold-out approach and found that its predictive power is very good for the GEV distribution location and scale parameters and improveable for the shape parameter, which is notoriously hard to estimate. The resulting discharge return levels yield satisfying agreement when compared with available design peak discharge from various government sources. Assessment of the covariates’ contributions to the model also informs on the most relevant underlying factors influencing flood-inducing peak flows. The key covariates in our model are temperature-related bioindicators, the catchment drainage area and geographical location.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

In 2011-2012, Northern Vietnam suffered its first large scale hand foot and mouth disease (HFMD) epidemic. Two sets of official guidelines were issued during the outbreak to handle the HFMD crisis. The city of Hai Phong was therefore used as a model to analyze the impact of the guidelines release. 9621 HFMD cases were reported in Hai Phong city from April 2011 to December 2012. Three distinct waves of HFMD occurred. Enterovirus A71 and Coxackievirus A16 were successively associated to the epidemics. Two periods, before and after guidelines realease, could be distinguished which were characterized by different patient patterns Time to admission and severity changed notably. Guideline publication help the health system refocusing on the 0.5-3 years age group with highest incidence of the disease. The three waves showed different special distribution but main routes of infection were rivers and local secondary roads most likely through local trade and occupational movements of people.

An HFMD outbreak spread over the city of Hải Phòng from Summer 2011 to Autumn 2012. This epidemic was chosen because it was the very first HFMD epidemic in North Vietnam, eliminating thus interferences with previous outbreaks. This epidemic displayed 3 separate waves. A complete dataset was collected for more than 9500 patients during this period, which enabled us to analyze this epidemic at different scales. Access to the healthcare system was crucial during this period, with a reorganization of the system in February-March 2012. An analysis at commune level enables us to track the epidemic along certain communication routes. The three-waves structure reveals a wide disparity at district level. We develop a mathematical model showing high accuracy at the adjustment of data for both the total number of cases and for the number of cases per week. As a consequence, the model was able to accurately determine the dates of beginning and end of each wave and to show that they overlapped. Using mathematical functions associated with this model, it was possible to calculate the probability for a patient to belong to a specific wave.

(1) Background: In orthognathic surgery, segmental Le Fort I osteotomies are a valuable method to correct maxillary deformities or transversal discrepancies. However, these procedures are technically challenging, and osteosynthesis can be prone to error. (2) Methods: In this retrospective, monocentric cohort study, patients were enrolled who underwent a virtually planned segmental maxillary osteotomy during their combined treatment. Positioning and osteosynthesis were achieved by either a 3D-printed splint and conventional mini plates or Patient-Specific Implants (PSI). The preoperative CT data, virtual planning data, and postoperative CBCT data were segmented. The deviation of all segments from the desired virtually planned position was measured using the analysis function of the IPS Case Designer. (3) Results: 28 Patients in the PSI Group and 22 in the conventional groups could be included. The PSI group showed significantly lower deviation from the planned position anteroposteriorly (-0.63±1.62mm vs. -1.3±2.54mm) and craniocaudally (-1.39±1.59mm vs. -2.7±3.1mm). For rotational deviations, the Pitch (0.64±2.59° vs. 2.91±4.08°) as well as the inward rotation of the lateral segments was positively influenced by PSI. (4). Conclusions: The presented data show that patient-specific osteosynthesis significantly reduces deviations from the preoperative plan in virtually planned cases. Especially transversal expansions and vertical positioning can be addressed better.

A highly crystallized monoclinic-scheelite type BiVO4 powders were successfully synthesized by solvothermal method. The as-synthesized BiVO4 powders were characterized by XRD, FE-SEM, Raman spectroscopy, UV-vis DRS spectroscopy and TA-PL. From the XRD data and Raman spectra, the monoclinic-scheelite phase BiVO4 sample can be obtained at higher solvothermal synthesis temperature more than 140 oC. The preparation conditions such as, the Bi/V molar ratio and synthesis temperature, have significantly effects on the morphologies of the BiVO4 samples. BVO2 sample shows the highest PL peak, which has the highest formation rate of OH radicals and the highest photocatalytic activity. This result suggests that the formation rate of OH radicals shows a good correlation with the photocatalytic activity.

An outbreak of novel coronavirus(2019-nCoV) that began in Wuhan, China, is rapidly spreading to all over China, and gradually to multiple countries. Regarding to put the epidemic prevention and spread under the control, early identification and diagnosis play a critical role. Patients with initially no or mild symptoms of Novel Coronavirus Pneumonia (2019-nCoV), namely “stealth” infection, often lack of typical clinical evidence to establish the diagnosis. Based on the clinical analysis of 4 cases in stealth infection, the results of this study highlight that early diagnosis requires a combination of epidemiological history, clinical manifestations, early chest CT examination, and 2019-nCoV RNA test (nucleic acid test), with particular emphasis on definite epidemiological history and early chest CT findings when positive nucleic acid tests lag behind.

Objectives: To compare the effects of high-velocity resistance training to slow-velocity re-sistance training on neuromuscular and functional parameters and to analyze the relationship between changes in walking speed and improvements in neuromuscular parameters following intervetions. Methods: 40 participants were randomly assigned to either a high-speed resistance training group (GHS, n = 18; age = 80.41 ± 10.12 years; BMI = 23.81 ± 3.45 kg/m²) or a low-speed resistance training group (GLS, n = 22; age = 82.89 ± 5.32 years; BMI = 23.81 ± 3.45 kg/m²). Before and after the interventions, gait speed (m/s) was assessed using a 10-minute walking test, and relative maximal force (Relative F max, N/kg) was evaluated during maximal voluntary isometric con-traction of the plantar flexors. From the force-time curve, early (0 – 50 ms) and late (100 – 200 ms) rates of force development (RFD) were extracted from the linear slopes (Δ force / Δ time). Results: Gait speed significantly improved in both groups (p < 0.05). However, the improvement was more pronounced in the GHS compared to the GLS (p < 0.05). Relative Fmax showed a more significant increase in the GLS than in the GHS (p < 0.05). Moreover, a significant 10% increase in early RFD in the GLS and a 20.1% increase in the GHS were observed (p < 0.05). The improvement in early RFD was greater in the GHS (p < 0.05). Additionally, late RFD improved significantly only in the GHS (+20.4%, p < 0.05). Conclusion: High-velocity resistance training appears particularly effective in improving the ability to rapidly generate force, which is essential for many daily activities re-quiring explosive movements and quick responses.

The emergence of the COVID-19 pandemic triggered a swift transition to online learning, remote work and an increased demand for proficiency in telehealth and digital health among health professions students as they prepare for their future careers. In responding to the question: “What are the essential constructs and the validity of a digital competence assessment scale for health professions students", this study sought to develop and validate a digital competence assessment scale (DigiCAS-HPS). The present study followed a mixed-methods approach: qualitative methods (phase 1) for generating and refining items in the scale through literature review on digital frameworks, pilot testing and expert review, and quantitative methods (phase 2) including exploratory and confirmatory factor analysis for its validation. The study revealed a two-factor structure, encompassing Digital Communication, Collaboration, and Online Security (Factor 1) and Digital Content Development and Software Mastery (Factor 2), demonstrating strong construct validity and reliability. Regarding differences in digital competence across groups, older and soon-to-graduate students exhibited higher proficiency in digital content development and software mastery. The two critical facets of DigiCAS-HPS scale could tailor training programs and ensure that health professions students are well-prepared for the evolving telehealthcare landscape. This promotes the growth and accessibility of telehealth, which is increasingly vital in the post-COVID-19 new normal era.

Cotton (Gossypium spp.) is the most important fibre crop worldwide. Black root rot and Fusarium wilt are two major diseases of cotton caused by soil-borne Berkeleyomyces rouxiae and Fusarium oxysporum f. sp. vasinfectum (Fov), respectively. Phenotyping plant symptoms caused by soil-borne pathogens has always been a challenge. To increase the uniformity of infection, we adapted a seedling screening method that directly uses liquid cultures to inoculate the plant roots and the soil. Four isolates each of B. rouxiae and Fov were collected from cotton fields in Australia and were characterised for virulence on cotton under controlled plant growth conditions. While the identity of all four B. rouxiae isolates were confirmed by multi-loci sequencing, only two of them were found to be pathogenic on cotton, suggesting variability in the ability of isolates of this species to cause disease. The four Fov isolates were phylogenetically clustered together with the other Australian Fov isolates and displayed both external and internal symptoms characteristic of Fusarium wilt on cotton plants. Furthermore, the isolates appeared to induce varied levels of plant disease severity indicating differences in their virulence on cotton. To contrast the virulence of the Fov isolates, four putatively non-pathogenic Fusarium oxysporum (Fo) isolates collected from cotton seedlings exhibiting atypical wilt symptoms were assessed for their ability to colonise cotton host. Despite the absence of Secreted In Xylem genes (SIX6, SIX11, SIX13 and SIX14) characteristic of Fov, all four Fo isolates retained the ability to colonise cotton and induce wilt symptoms. This suggests that slightly virulent strains of Fo may contribute to the overall occurrence of Fusarium wilt in cotton fields. Findings from this study will allow better distinction to be made between plant pathogens and endophytes and allow fungal effectors underpinning pathogenicity to be explored.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Due to its application as an anti-cancer drug, pazopanib (1) has attracted the interest of many researchers and several studies on pazopanib synthesis have been reported over the years. This paper provides a novel route for synthesizing N,2,3-trimethyl-2H-indazol-6-amine (5) which is a crucial building block in the synthesis of pazopanib from 3-methyl-6-nitro-1H-indazole (6). By alternating between the reduction and two methylation steps compound 5 was obtained in comparable yield (55.0%) to what has been reported (54%). Noteworthy, the last step of N2-methylation also yielded N,N,2,3-tetramethyl-2H-indazol-6-amine (5’) as a new compound ever reported. Furthermore, the data presented in this paper can serve as instrumental for future research aimed at further refining the synthesis process of pazopanib.

A convenient and fast multiresidue method for the efficient identification and quantification of 72 pesticides belonging to different chemical classes in red and white grape wines have been developed. The analysis was based on gas chromatography tandem quadrupole mass spectrometric determination (GC–MS/MS). An optimization strategy involved the selection of MWCNTs amount and cleanup procedure cycle times for m-PFC was performed to achieve ideal recoveries and reduce sample matrix compounds in the final extracts. The optimized procedure obtained consistent recoveries between 70.2 and 108.8% (70.2% and 108.8% for white wine, 72.3% and 106.0% for red wine) , with relative standard deviations (RSDs) generally lower than 8.3% at three spiking levels of 0.01, 0.05 and 0.2 mg/kg. Linearity was studied in the range between 0.005 and 0.2 mg/kg using pesticide standards prepared both in pure solvent and in the presence of matrix, showing coefficients of determination (R²) higher than 0.985 for all the pesticides. To improve accuracy, matrix matched calibration curves were used for calculating the quantification results. Finally, the method was used successfully in detecting pesticide residues in commercial gape wines.

The so-called “Chinese pyramids” are huge burial mounds covering the tombs of the Emperors of the Western Han dynasty. If we include also the mounds of the members of the royal families, these monuments sum up to more than 40, scattered throughout the western and the southern outskirts of modern Xi'an. They are mostly unexcavated and poorly known although, taken together, they form a fascinating sacred landscape, which was conceived as a perennial witness of one of the most magnificent Chinese dynasties. This sacred landscape is today encroached by the frenetic urban development of the Xi’an urban area. We discuss and elaborate here some of the results of a recent, new satellite-imagery survey of these monuments, highlighting the aspects which may contribute to solutions for a sustainable and compatible development within this important ancient landscape.

Wool quality and yield are important economic traits of livestock. In this study, the skin tissues of the upper scapula of Super Merino sheep (SM) and Small-Tailed Han sheep (STH) during the growing period were studied. Differentially expressed (DE) long non-coding RNAs (lncRNAs) and messenger RNAs (mRNA) were identified via histopathological observation and high-throughput RNA sequencing. Gene ontology (GO) and the Kyoto Encyclopedia of Genes and Genomes (KEGG) were used to analyze differentially expressed genes. Reverse transcription quantitative Polymerase Chain Reaction (RT-qPCR) was used to verify nine selected DE lncRNAs and five DE mRNAs. Significant differences were found in the expression levels of LOC114113396 (KRTAP15-1), CRABP1, KRT10, KRTAP1-3, KRTAP4.3, KRT2, FGF1, IGF-1, and KIT in SM and STH skin tissues. These results indicate that these mRNAs may play an important role in the growth and development of hair follicles and the regulation of hair fiber traits. Differentially expressed lncRNA target genes and mRNAs were mainly enriched in biological processes and pathways related to skin development and fiber traits, which is consistent with previous studies. LncRNA MSTRG.9225.1, MSTRG.124320.1, MSTRG.96951.1, MSTRG.91685.1, MSTRG.122229.1, MSTRG.89255.1, MSTRG.98769.1, and MSTRG.84658.1 may indirectly participate in the growth and development of sheep hair follicles and the regulation of hair fiber diameter by regulating the expression of their respective target genes. These candidate lncRNAs and mRNAs may provide a basis for the study of sheep hair follicle growth and development and hair fiber traits.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

The aim of this paper is to compare the taxonomic composition and species diversity of the macrozoobenthos in Maritsa River (Bulgaria) and Han River (South Korea). Samples were collected at 15 selected sites in each river, including some of their main tributaries in 2020 and 2021. The number of the taxa recorded in Maritsa River was more than twice as great as in Han River: 192 taxa belonging to 19 systematic groups compared to 88 taxa belonging to 18 groups respectively. The order Ephemeroptera had the highest species richness: 31 taxa in the Bulgarian rivers and 26 taxa in the South Korean ones. The macrozoobenthic communities responded and adapted to the various conditions and impacts in the water environment with changes in the species composition and structure. The analysis of the similarity in the taxonomic composition showed low resemblance between all study sites but displayed distinct separations between the rivers and the two years. In general, the species structure of the macrozoobenthic communities in Maritsa River and its studied tributaries was better than in Han River. In both years, high species diversity was recorded at the reference sites in the rivers, characterized by conditions closely resembling natural environments. The species richness and the evenness of macrozoobenthos were very low at sites downstream subjected to considerable anthropogenic pressure. Some of the communities in Han River were almost destroyed completely.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Verticillium wilt is a soil borne disease caused by distinct vegetative compatibility groups (VCG) of the fungus Verticillium dahliae. Two V. dahliae isolates were recovered from symptomatic cot-ton plants in Australian cotton fields and were assigned to two distinct vegetative compatibility groups (VCGs). One corresponding to the defoliating (VCG 1A) and the other non-defoliating (VCG 2A) pathotypes of Verticillium, have been transformed with Red and Green Fluorescent protein genes, respectively. The transformants maintained their ability to infect cotton and both strains were observed to colonise the xylem vessels of cotton plants. Moreover, we observed that the cotton V. dahliae strains could also infect some sampled non-Gossypium species found in the Australian landscape. The fluorescently labelled strains of V. dahliae will allow us to gain a thorough understanding of the infection processes of this important pathogen.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

This study aimed to characterize the long non-coding RNA (lncRNA) expression in the bovine mammary gland and to infer their functions in dietary response to 5% linseed oil (LSO) or 5% safflower oil (SFO). Twelve cows (six per treatment) in mid lactation were fed a control diet for 28 days followed by a treatment period (control diet supplemented with 5% LSO or 5% SFO) of 28 days. Mammary gland biopsies were collected from each animal on day-14 (D-14, control period), D+7 (early treatment period) and D+28 (late treatment period) and were subjected to RNA-Sequencing and subsequent bioinformatics analyses. Functional enrichment of lncRNA was performed via potential cis regulated target genes located within 50 Kb flanking regions of lncRNAs and having expression correlation of >0.7 with mRNAs. A total of 4955 lncRNAs (325 known and 4630 novel) were identified which potentially cis targeted 59 and 494 genes in LSO and SFO treatments, respectively. Enrichments of cis target genes of lncRNAs indicated potential roles of lncRNAs in immune function, nucleic acid metabolism and cell membrane organization processes as well as involvement in Notch, cAMP and TGF-β signaling pathways. Thirty-two and 21 lncRNAs were differentially expressed (DE) in LSO and SFO treatments, respectively. Six genes (KCNF1, STARD13, BCL6, NXPE2, HHIPL2 and MMD) were identified as potential cis target genes of six DE lncRNAs. In conclusion, this study indicated potential roles for lncRNAs in mammary gland immune functions and development and provided potential candidate genes and pathways via which lncRNAs can function in diet responses.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

Utilizing unmanned aerial vehicles (UAVs) to facilitate wireless communication has emerged as a viable and promising strategy aimed at enhancing both current and prospective wireless systems. This approach offers many advantages by establishing line-of-sight connections, optimizing operational efficiency, and enabling flexible deployment capabilities in various terrains. Thus, in this paper, we investigate UAV communication in a relaying network in which a UAV helps communication between a source and two destination users while flying to a location. To have a complete view of our proposed system, we consider both orthogonal multiple access as OFDM and non-orthogonal multiple access (NOMA) scenarios. Moreover, we apply successive convex optimization (SCO) and the Block-coordinate gradient descent (BCGD) for the sum-rate optimization problems to improve the system performance under constraints of total bandwidth and total power at the ground base station and UAV. The experimental results validate that the achievable secrecy rates are notably enhanced by using our proposed algorithms and show optimal trends for critical parameters, such as transmit powers, the flight trajectory and speed of UAV, and resource allocation of OFDM and NOMA.

The Giant Babax, an endemic bird in China and a nationally protected wildlife species of Class Ⅱ, is primarily distributed in southern and southeastern Tibet. To investigate the factors influencing nesting site selection, this study conducted research on nest characteristics and nesting site preferences at four sample sites around Lhasa from March to October 2023y, using systematic search methods, tracking methods, and sampling methods. The research findings are as follows: (1) The average nest depth was (7.70±1.47)cm, nest height was (19.58±2.97)cm, inner diameter was (10.64±1.73)cm, outer diameter was (24.65±4.8)cm, average weight was (162.3±13.5)g, and average nest spacing within the plot was 396.93m. (2) The nests of Giant Babax were predominantly found on vegetation such as Salix longistamina (38%), Hippophae gyantsensis (20%), Rosa sericea Lindl. (14%), and Populus szechuanica Schneid(11%). They showed a preference for artificial secondary forests as nesting sites. (3) Giant Babax exhibited a preference for habitats with robust trees that had high canopies while being distant from houses and roads, but close to water sources; moreover, the canopy of the nesting tree played a crucial role in their choice of nesting sites. (4) The reproductive success rate reached 76%, with key factors affecting it being the canopy coverage of the nesting tree and the number of helpers. These research results provide fundamental data support for population conservation efforts and ecological resource management strategies concerning the Giant Babax.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

Ce³⁺ and Dy³⁺ ions doped Ca₂Al₂SiO₇ (CAS) phosphors were prepared by the solid-state reaction at 12800C for 1h. X-ray diffraction patterns confirmed a tetragonal crystalline structure. The luminescent spectra of CAS: Ce³⁺, Dy³⁺ phosphors consist a board band with peaking at 420 nm corresponding to the luminescence of Ce³⁺ ions and narrow lines of Dy³⁺ ions. The energy transfer from Ce³⁺ ion to Dy³⁺ ion is presented and discussed

The last decade has seen a significant growth in low-cost air quality monitoring systems (LCAQMS) adoption, mostly driven by the spatial density limitations of traditional regulatory grade networks which restrict their effectiveness in several settings. The EU's regulatory framework advise for deploying one air quality monitoring unit per roughly 170,000 people or 15 square kilometers which is insufficient for capturing high spatio-temporal variance in complex urban scenarios. Often these settings are characterized by distributed emissions in small roads subjected to intense cars traffic, house heating driven emissions and frequently subjected to canyon effects. The Air Heritage project in Portici, funded by the EU's Urban Innovative Actions (UIA) program, addressed these challenges by integrating low-cost sensors with traditional monitoring systems and engaging the community in pervasive measurement strategies. The project highlights the importance of individualized sensor calibration and frequent recalibrations to maintain accuracy. It also showcases the benefits of citizen science approaches, IoT infrastructures, AI components, and geostatistical sensor fusion algorithms for mobile and opportunistic air quality measurements. This paper reports on the lessons learned and experiences from the Air Heritage project, aiming to guide future implementations in similar contexts. By sharing these insights along with the gathered datalake, we aim to inform stakeholders, including researchers, public authorities, and citizens, about effective strategies for deploying and utilizing LCAQMS to enhance air quality monitoring and public awareness.

We give a series of numerical examples of competitive evolution in the predation system, showing in some cases how the choice is made to increase the efficiency of the predation mechanism (or other significant parameters) to the detriment of populations (both of prey and predators). We then develop the mathematical theory that enables us to understand the causality involved, and identify a trend towards the emergence of the functional predation mechanism as such (and not of populations of the species involved). The realization of this trend only takes place when the conditions for it are offered by the hazards proposed to successive competitive choices. The logical structure of this trend is similar to that of the « tendency of rate of profit to fall » in certain economic models.

MicroRNAs (miRNAs) are small endogenous RNAs that regulate gene expression post-transcriptionally by targeting either the 3′ untranslated or coding regions of genes. They have been reported to play key roles in a wide range of biological processes. The recent remarkable developments of transcriptomics technologies, especially next-generation sequencing technologies and advanced bioinformatics tools, allow more in-depth exploration of messenger RNAs (mRNAs) and non-coding RNAs (ncRNAs) including miRNAs. These technologies have offered great opportunities for a deeper exploration of miRNA involvement in farm animal diseases, as well as livestock productivity and welfare. In this review, we provide an overview of the current knowledge of miRNA roles in farm animal diseases with a particular focus on diseases of economic importance. In addition, we discuss the steps and future perspectives of using miRNAs as biomarkers and molecular therapy for livestock disease management as well as the challenges and opportunities for understanding the regulatory mechanisms of miRNAs related to disease pathogenesis.

This paper examines the relationship between the ratio of independent board member to the financial performance of the company under the mediation of the three pillars of environment, society, and governance (ESG) in Taiwan. The study addresses a research gap between independent directors and corporate financial performance, an issue that is rarely discussed today. The author develops the hypotheses and tests them by applying panel data regression to the data tables taken from the Thomson Reuters Eikon database to analyze data on 173 Taiwanese companies that reported ESG from 2009 to 2021. The results show that the relationship between the ratio of independent directors and financial performance has a positive relationship. At the same time, the 3 pillars of ESG also clearly show the intermediary role in this relationship. Finally, this study provides additional insights into the relationship between the ratio of independent directors and financial performance in the Taiwan context.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

Nowadays, wearable devices for human health monitoring are increasingly become popular and widely used. Typically, the wearable device is small size and operates with batteries. Therefore, the wearable device acquires bio-signals and transfers to smartphones or personal computers (PC) via WiFi/ Bluetooth for processing data. To reduce power consumption is one of the most important challenges of designing wearable devices. To solve this problem, the proposed signal quality valuation (SQV) method can be select the high-quality signal and reduce the transfer time to other devices. In this paper, the proposed SQV and data compression method rely on real-time PPG signals analysis to retain important information of PPG signal, improve performance and power consumption of PPG devices. Besides, we also proposed Heuristic rules for heart rate (HR) estimation with compression data. The experimental results show that the highest compression ratio (CR) is 387.8 with BIDMC Physionet database (sampling frequencies of 125 Hz) and HR error as 1.43 bpm for averaging absolute error (avAE), the standard deviation absolute error (sdAE as 0.4) and relative error mean (avRE as 0.019). The proposed real-time PPG measurement system (sampling frequency as 100/ 200/ 400 Hz) reduce power consumption and open the new structure for healthcare application systems

Climate change is an important threat to orchard production at Mediterranean basin. Diversification seems to be implemented at a farm level as an important strategy to face these challenges. This paper aims to analyse farmer’s perceptions on crop diversification as a way to enhance farm’s adaptive capacity in a context of current and future climate changes impacts. Our case study is focused in orchards growers from French department of Vaucluse recently diversifying their activities through pistachio (Pistacia vera L.). We did in-depth semi-structured farmers’ interviews in 2021. The results show that diversification is supposed to enhance 3 main components of farms adaptative capacity: (1) strengthening robustness through improvement of buffering capacities to climate impacts (trough robust and adapted plants), economic uncertainties (by exploring local/niche markets) and labour scarcity (by lowering workforce requirements and mechanization); (2) Learning by experimenting, monitoring and exchanging with pairs and advisors (3) Cope with change related with societal demands and helps to increase personal satisfaction. Finally, promote farm’s diversification can contribute to enhance farm’s adaptive capacity under climate change impacts.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Arbuscular mycorrhizal fungi (AMF) are soil microorganisms living in symbiosis with most terrestrial plants. They are known to improve plant tolerance to numerous abiotic and biotic stresses through the systemic induction of resistance mechanisms. With the aim of developing a more sustainable agriculture, reducing the use of chemical inputs is becoming of a major concern. After providing an overview on the AMF history, phylogeny, development cycle and the symbiosis benefits, the current review aims at exploring the potential of AMF as biostimulants and/or biocontrol agents. Nowadays, AMF inoculums are already increasingly used as biostimulants, improving mineral nutrient plant acquisition. However, their role as promising tool into the biocontrol market, as alternative to chemical phytosanitary products, is underexplored and discussed. Thus, in the current review, we will address the mechanisms of mycorrhized plant resistance to biotic stresses induced by AMF, and highlight the various factors in favor of inoculum application, but also the challenges that remain to be overcame.

Apoptosis, the programmed and intentional death of senescent, damaged, or otherwise superfluous cells, is the natural end-point for most cells within multicellular organisms. Apoptotic cells are not inherently damaging, but if left unattended they can lyse through secondary necrosis. The resulting release of intracellular contents drives inflammation in the surrounding tissue and can lead to autoimmunity. These negative consequences of secondary necrosis are avoided by efferocytosis—the phagocytic clearance of apoptotic cells. Efferocytosis is a product of both apoptotic cell and efferocyte mechanisms, which cooperate to ensure the rapid and complete removal of apoptotic cells. Herein, the processes used by apoptotic cells to ensure their timely removal, and the receptors, signaling, and cellular processes used by efferocytes to identify, remove, and process the apoptotic cells, are reviewed.

To avoid loss of information and incorrect ranking, this paper proposes a method for ranking generalized fuzzy numbers, which guarantees both horizontal and vertical values are important parameters affecting the final ranking score. In this method, the normalized height coefficient is introduced to evaluate the influence of the height of fuzzy numbers on the final ranking score. The higher the normalized height coefficient of a fuzzy number is, the higher its ranking. The left area and the right area are presented to calculate the impact of vertical value on the final ranking score. The left area is considered the benefit area. The right area is considered the cost area. The fuzzy number is preferred if the benefit area is larger and the cost area is smaller. The proposed method can be employed to rank both normal and non-normal fuzzy numbers without normalization or height minimization. Numerical examples and comparison with other methods highlight the feasibility and robustness of the proposed method, which can overcome the shortcomings of some existing methods and can support decision-makers to select the best alternative.

Lipid nanoparticles have an interesting part of drug delivery system. In this study, the modification of the convention nano-lipid based soybean lecithin was demonstrated. Ginger oil derived Zingiber officinale was used along with lecithin, cholesterol and span 80 to fabricate nano-lipid (GL nano-lipid) using thin-film method. Through TEM and confocal microscope, GL nano-lipid exposes the liposome- like morphology. The average size of the resultant nanoparticles was 249.1nm with monodistribution (PDI= 0.021). The ζ-potential of GL nano-lipid was negative as similar to as prepared nano-lipid based lecithin. GL nano-lipid express the highly stable over 60 days of storage at room temperature in term of size, ζ-potential. A shift of pH value from alkaline to acid was detected in lecithin nano-lipid, while with the incorporation of ginger oil, pH value of nano-lipid dispersion was around 7.0. Furthermore, due to the rich of shogaol-6 and other active compounds in ginger oil, the GL nano-lipid is endowed with intrinsic antibacterial feature. In addition, the sulforhodamine B (SRB) assay and live/dead imaging revealed the excellent biocompatibility of GL nano-lipid. Notably, GL nano-lipid was capable to carry the hydrophobic agents as curcumin and perform a pH-dependent release profile. A subsequent characterization are a suitable potential for drug delivery system.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

This paper presents the findings of an exploratory study on the continuously generating Big Data on Twitter related to the sharing of information, news, views, opinions, ideas, knowledge, feedback, and experiences about the COVID-19 pandemic, with a specific focus on the Omicron variant, which is the globally dominant variant of SARS-CoV-2 at this time. A total of 12028 tweets about the Omicron variant were studied, and the specific characteristics of tweets that were analyzed include - sentiment, language, source, type, and embedded URLs. The findings of this study are manifold. First, from sentiment analysis, it was observed that 50.5% of tweets had the ‘neutral’ emotion. The other emotions - ‘bad’, ‘good’, ‘terrible’, and ‘great’ were found in 15.6%, 14.0%, 12.5%, and 7.5% of the tweets, respectively. Second, the findings of language interpretation showed that 65.9% of the tweets were posted in English. It was followed by Spanish or Castillian, French, Italian, Japanese, and other languages, which were found in 10.5%, 5.1%, 3.3%, 2.5%, and <2% of the tweets, respectively. Third, the findings from source tracking showed that “Twitter for Android” was associated with 35.2% of tweets. It was followed by “Twitter Web App”, “Twitter for iPhone”, “Twitter for iPad”, “TweetDeck”, and all other sources that accounted for 29.2%, 25.8%, 3.8%, 1.6%, and <1% of the tweets, respectively. Fourth, studying the type of tweets revealed that retweets accounted for 60.8% of the tweets, it was followed by original tweets and replies that accounted for 19.8% and 19.4% of the tweets, respectively. Fifth, in terms of embedded URL analysis, the most common domains embedded in the tweets were found to be twitter.com, which was followed by biorxiv.org, nature.com, wapo.st, nzherald.co.nz, recvprofits.com, science.org, and other URLs. Finally, to support similar research and development in this field centered around the analysis of tweets, we have developed an open-access Twitter dataset that comprises tweets about the SARS-CoV-2 omicron variant since the first detected case of this variant on November 24, 2021.

Perception of flavor is a dynamic process during which the concentration of aroma molecules at the olfactory epithelium varies with time as they are released progressively from the food in the mouth during consumption. The release kinetics depends on the food matrix itself, but also on food oral processing, such as mastication behavior and food bolus formation with saliva, for which huge inter-individual variations exist due to physiological differences. Sensory methods, such as time-intensity (TI), or the more recent methods temporal dominance of sensations (TDS) and temporal check-all-that-apply (TCATA), are used to account for the dynamic and time-related aspects of flavor perception. Direct injection mass spectrometry (DIMS) techniques that measure in real-time aroma compounds directly in the nose (nosespace), aimed at obtaining data that reflect the pattern of aroma release in real-time during food consumption, supposed to be representative of perception, have been developed since 25 years. Examples obtained with MS operated in chemical ionization mode at atmospheric or sub-atmospheric pressure (atmospheric pressure chemical ionization APCI or proton transfer reaction PTR) will be given, with emphases on studies conducted with simultaneous dynamic sensory evaluation. Inter-individual variations in terms of aroma release and their relevance for understanding flavor perception will be discussed, as well as evidenced cross-modal interactions.

High-throughput research on bimetallic nanoparticles brought a vast overview of their characteristics and catalytic activities.¹ However, traditional bimetallic nano-allloy quantification methods serving catalyst preparations are not suitable for the fast and robust data output of high-throughput experiments. Hence, this work designed and validated a more fast, more neat, and reliable quantitative analysis using X-ray fluorescence spectroscopy for bimetallic nanoparticles synthesized by high-throughput setups. The results demonstrated this method to be accurate with high precision. Furthermore, the agreement to qualitative results from an energy-dispersive X-ray spectrometer equiped on a scanning electron microscope provided an option to quantify a bimetallic nano-alloy by just analyzing one of the two composing elements. Thus, this method is proved to be highly compatible with high-throughput experiments.

A complete MAPLE procedure is designed to implement effectively an algorithm for approximating the trigonometric functions. The algorithm gives a piecewise polynomial approximation on an arbitrary interval, presenting a special partition that we can get its parts, subintervals with ending points of finite rational numbers, together with corresponding approximate polynomials. The procedure takes a sequence of pairs of interval-polynomial as its output that we can easily explore in some useful ways. Examples on calculating approximate values of the sine function with arbitrary accuracy for both of rational and irrational arguments as well as drawing the graph of the piecewise approximate functions will be presented. Moreover, from the approximate integration of integrands of the form $x^m\sin x$ on $[a,b]$, another MAPLE procedure is proposed to find the desired polynomial estimates in norm for the best $L^2$-approximation of the sine function in the vector space $\mathcal{P}_{\ell}$ of polynomials of degree at most $\ell$, a subspace of $L^2(a,b)$.

Vietnam is the second largest coffee producer in the world, mostly from the Central Highlands region where water has been becoming a scarce resource. Since 2014, drought has been strongly affecting Central Highlands’ agriculture, particularly coffee production. The drought leads to changes in flowering, ripening and thus harvesting times of coffee. Coffee productivity has reduced about 50 percent. Ultimately, coffee quantity and quality is jeopardized which endangers coffee farmers who occupy 90 per cent of population and their livelihoods mainly rely on coffee. Most of coffee farmers have had to develop alternative strategies to respond to the drought. Based on quantitative and qualitative data collected from 50 coffee households in a community in the Central Highlands, this research has indicated that farmers had to find the ways to adapt as well as to cope with drought. The ways of adaptation and coping were diverse, including short, medium and long-term plans. To strengthen the adaptation and coping strategies of farmers with drought in the short term, it is recommended that authorities provide more technical and financial support to farmers. Furthermore, longer term strategies need to focus on land use planning, investment in irrigation schemes, and consolidated afforestation schemes in appropriate areas.

Two isolates of Acinetobacter were isolated from the soil samples of motorbike repairing workshop floors in Vietnam, where motorcycle/scooter repairs generate various types of hazardous waste, including mainly used waste oil and fluids. Two isolates were Gram-stain-negative, coccobacilli-shaped, aerobic, non-motile, non-hemolytic, oxidase-negative, and catalase-positive, designated strains VNH17T and VNK23T. Growth of strains was inhibited by NaCl concentrations above 3% and grew at an optimal temperature of 20-35°C. Phylogenetic analysis based on 16S rRNA gene sequences revealed that two isolated strains formed a lineage within the family Moraxellaceae and clustered as members of the genus Acinetobacter. The predominant respiratory quinones of VNH17T and VNK23T are ubiquinone 9 and ubiquinone 8, and the polar lipids are mainly composed of diphosphatidyl glycerol, phosphatidylglycerol, and phosphatidylethanolamine. The major cellular fatty acids are C18:1ω9c, C16:0 and summed feature 3 (C16:1ω7c and/or C16 : 1ω6c). The DNA G+C content of VNH17T and VNK23T was 42.07% and 41.75%, respectively. In addition, the average nucleotide identity and in silico DNA-DNA hybridization relatedness values between VNH17T and VNK23T as well as between they and phylogenetically related type strains were below the threshold values used for species delineation. Based on genomic, chemotaxonomic, phenotypic and phylogenomic analyses, the isolated strains represent novel species in the genus Acinetobacter, for which the names Acinetobacter thutiue sp. nov. (type strain VNH17T = KACC 23003 = CCTCC AB 2023063), Acinetobacter kontum sp. nov. (type strain VNK23T = KACC 23002 = CCTCC AB 2023064) are proposed.

The goals of the Agenda 2030 require a significant effort to educate and train new generations on sustainability issues. This article presents an initiative in favor of the evolution of the contents and the pedagogy of economics at the University level. We present the new “Ecological Money and Finance” textbook developed by SDSN France. We detail the assumptions, contents and learning objectives proposed in this new textbook. Then, we describe how it can be used in the framework of an experiential pedagogy of economics, taking as a case study the fundamental economics course of the Grande Ecole program at KEDGE BS.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

This paper reports aligned activities to promote energy and resource-efficient construction practice in Vietnam. First, the governance framework is introduced, including government decrees and technical standards. Then, a laboratory with building physics measurement technology is designed and partly set up at the local partner Vietnam Institute for Building Materials (VIBM), which can be used to determine the essential characteristic values required for the implementation of energy standards. The basis for the prioritization of the characteristic values are the requirements of the National technical regulation on energy efficient buildings of Vietnam – QCVN09:2017/BXD. Furthermore, basic characteristic values from international standards are described, which can also be used for calculations to optimize the energy consumption of buildings. In order to be able to carry out transient hygrothermal computer simulations, special characteristic values were also included. These are particularly useful for the research and development of new building materials and the evaluation of entire buildings in terms of thermal and moisture protection In order to communicate the material properties to the market and enable informed decision making by the stakeholders, a labeling system has been developed. Thereby, the practical means for implementing governance instruments are provided, and the related technical applications are supported.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

Quaternion and biquaternion symmetry transformations have been applied to non-Cartesian reference systems of direct and reciprocal crystal lattices. The transformations performed directly in the sets of crystal reference axes simplify the calculations, eliminate the need for orthogonalization, permit the use of crystallographic vectors for defining the directions of rotations and perform the computations directly in the crystal coordinates. The applications of the general quaternion transformations are envisioned for physical, chemical, crystallographic and engineering applications. The general quaternion multiplication rules for any symmetry-unrestricted lattices have been derived for the triclinic crystallographic system and have been applied to the biquaternion representations of all point-group symmetry elements, including the crystallographic hexagonal system. Cayley multiplication matrices for point groups, based on the biquaternion symbols of proper and improper symmetry elements, have been exemplified.

Protein import into the endoplasmic reticulum (ER) is the first step in the biogenesis of about 10,000 different soluble and membrane proteins in humans. It involves co- or post-translational targeting of precursor polypeptides to the ER and their subsequent membrane insertion or translocation. So far, three pathways for ER targeting of precursor polypeptides plus four pathways for ER targeting of mRNAs were described. Typically, these pathways deliver their substrates to the Sec61 polypeptide-conducting channel in the ER membrane. Next, the precursor polypeptides are inserted into the ER membrane or translocated into the ER lumen, which may involve auxiliary translocation components, such as the TRAP and Sec62/Sec63 complexes, or auxiliary membrane protein insertases, such as EMC and the TMCO1 complex. Recently, the PEX19/PEX3-dependent pathway, which has a well-known function in targeting and inserting various peroxisomal membrane proteins into pre-existent peroxisomal membranes, was also found to act in targeting and, putatively, inserting monotopic hairpin proteins into the ER. These either remain in the ER as resident ER membrane proteins or are pinched off from the ER as components of new lipid droplets. Therefore, the question arose if this pathway may play a more general role in ER protein targeting, i.e. represents a fourth pathway for ER targeting of precursor polypeptides. Thus, we addressed the client spectrum of the PEX19/PEX3-dependent pathway in both PEX3-depleted HeLa cells and PEX3-deficient Zellweger patient fibroblasts by an established approach, which involves label-free quantitative mass spectrometry of the total proteome of depleted or deficient cells and differential protein abundance analysis. The negatively affected proteins included twelve peroxisomal proteins and two hairpin proteins of the ER, thus confirming two previously identified classes of putative PEX19/PEX3-clients in human cells. Interestingly, fourteen collagen-related proteins with signal peptides or N-terminal transmembrane helices and belonging to the secretory pathway were also negatively affected by PEX3-deficiency, which may suggest compromised collagen biogenesis as a hitherto unknown contributor to organ failures in the respective Zellweger patients.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

The Samenta study was conducted in 2009 in the Greater Paris area to estimate the prevalence of psychiatric disorders among the homeless. A cross-sectional survey was performed with a three-stage random sample of homeless people (n = 859), including users of day services, emergency shelters, hot meal distribution, long-term rehabilitation centres and social hotels. Information was collected by a lay interviewer, using the Mini International Neuropsychiatric Interview, and completed by a psychologist through an open clinical interview. In the end, a psychiatrist assessed the psychiatric diagnosis according to the ICD10. One third of the homeless in the Paris area had at least one severe psychiatric disorder: psychotic disorders (13%), anxiety disorders (12%) or severe mood disorders (7%). One in five was alcohol dependent and 18% were drug users. Homeless women had significantly higher prevalence of anxiety disorders and depression and men were more likely to suffer from psychotic disorders. Homeless people of French origin were at higher risk of SPD, as well as people who experienced various adverse life events before the age of 18 (running away, sexual violence, parental disputes, and/or addictions) and those who experienced homelessness for the first time before the age of 26. The prevalence rates of main psychiatric disorders within the homeless population of our study are consistent with those reported in other Western cities. Our results advocate for an improvement in detection, housing and care of psychiatric homeless.

Postpartum haemorrhage remains a significant contributor to maternal mortality and morbidity worldwide, particularly in low- and middle-income countries. PPH continues to pose challenges in both developed and developing nations despite being preventable. This review examines the current state of knowledge regarding PPH within the context of Vietnam, a country with its unique healthcare landscape. This review identifies critical areas for improvement and future research directions based on a comprehensive literature analysis, including epidemiological insights, risk factors, prevention strategies, and management approaches. Discrepancies in PPH definitions and prevalence rates across regions highlight the need for tailored interventions and policies. Understanding the specific challenges and opportunities related to PPH in Vietnam is crucial for informing evidence-based interventions and policies to improve maternal health outcomes. This review contributes to the broader global effort to reduce maternal mortality by addressing gaps in knowledge and proposing strategies to enhance PPH prevention and management in Vietnam.

Aim: We estimated the correlation between serum bilirubin concentrations and insulin resistance in advanced maternal age without diabetes mellitus. Method: The cross-sectional study involved consecutive 50 women of advanced maternal age without diabetes mellitus, and insulin resistance (IR) was diagnosed according to the homeostatic model assessment insulin resistant (HOMA-IR) formula and the cut-off point was set to more than 2.5. Serum bilirubin and HOMA-IR were compared between the IR (+) and IR (-) groups. Results: We found that serum bilirubin levels in the IR subjects were significantly decreased compared to those without IR (p = 0.0252). Serum bilirubin concentrations were negatively correlated with the weight and the fasting insulin concentrations in all subjects (r=−0.282, p=0.047, r=-0.424, p=0.002). Additionally, serum bilirubin had a negatively correlation with HOMA-IR (r = -0.410, p = 0.003) in all subjects. The multiple linear regression analysis found that serum total bilirubin levels were independently correlated with HOMA-IR (beta = -0.392, p= 0.015) in these subjects. Conclusions: The study demonstrated that serum bilirubin concentrations had negatively correlation with insulin resistance in advanced pregnant women without diabetes mellitus, and decreased serum bilirubin may forebode increased gestational diabetes mellitus risk in our study population.

This paper introduces in general the conservation work of the Nara Palace Site in Japan carried out by Japanese conservation experts. Concerning conservation theory, this paper focused on the international conventions in which the 1994 Nara Document on Authenticity plays an important role in contributing to Japanese cultural heritage conservation achievements with the expansion of Cultural diversity and Heritage diversity, the Values and Authenticity conceptions which proposed a new orientation in terms of awareness and openness broader vision in identifying architectural heritage values. Regarding, based on the 1994 Nara Document on Authenticity, the 1964 Venice Charter, and the 1999 Bura Charter, we try to propose a new concept of the so-called “Architectural Heritage DNA” and its potential structure, providing a simple formula for the authentic values appraisal of the heritage conservation works. In addition, we also try to supplement the concept of Inheritance between Conservation and Development which is the lack of international conventions of cultural heritage conservation. The viewpoints expressed in this paper are based on the most common concepts of international conventions but interpreted in a new-understandable, practical, and highly applicable way possible to the current socio-political situation and in the future, as well.

(1) This study aimed to examine the prevalence of depression and its correlation with acculturative Stress and Social Connectedness among domestic and overseas students in Japan International University. (2) Methods: A Web-based survey was distributed among students of International University, which resulted in 263 responses. On the survey together with socio-demographic data, a nine-item tool from the Patient Health Questionnaire (PHQ-9), was used to measure the prevalence of Depression and its relationship with socio-demographic data, Social Connectedness Scale was used to measure Social Connectedness, and Acculturative Stress Scale for International Students (ASSIS) was used to measured acculturative stress. (3) Results: Depression was significantly high in international and domestic students (37.81% and 29.85% respectively). English language proficiency and students age (20 years old) showed a significant correlation with depression among domestic students (β=-1.63, p=0.038 and β=2.24, p=0.048). Stay length (third year) also displayed a significant correlation with depression among international students (β=1.08, p=0.032). Among international and domestic students statistically significant positive correlation between depression and acculturative stress, negative associations of social connectedness with depression and acculturative stress were also found. Suicidal or self-hurting ideation thoughts are found among around 20% of all students. (4) Conclusions: These findings indicate a relatively high prevalence of depression among students of International University, and overseas students are more affected. Depression, Acculturation stress and Social Connectedness show statistically strong intercorrelation, which highlights the need of host University to recognise the role of Acculturation and Social Connectedness in the development of Depression among students.

Obesity has become a global epidemic, contributing to the development of numerous chronic diseases, including diabetes, chronic kidney disease (CKD) and cardiovascular disorders. MicroRNAs (miRNAs) have emerged as key regulators in various biological processes, including metabolism, inflammation, and tissue remodeling, making them pivotal players in obesity-related pathologies. This review aims to provide comprehensive insights into the roles of miRNAs in obesity, with a particular emphasis on their involvement in the pathogenesis of CKD and cardiovascular disorders. We highlight the involvement of specific miRNAs in adipose tissue development, energy homeostasis, inflammation, and insulin resistance, contributing to the pathogenesis of obesity. Moreover, we explore the impact of miRNAs on renal fibrosis, and inflammation, giving clues on their roles in the development and progression of CKD. Additionally, we discuss the influence of miRNAs on endothelial dysfunction, atherosclerosis, and cardiac remodeling, emphasizing their contribution to obesity-related cardiovascular disorders. Understanding the regulatory functions of miRNAs in these interconnected conditions holds promise for improved diagnosis, prognosis, and therapeutic interventions. Indeed, miRNAs are potential diagnostic biomarkers for obesity-related diseases although challenges remain to be elucidated before their clinical translation. Furthermore, we highlight the emerging strategies that target miRNAs as therapeutic interventions to mitigate the detrimental effects of obesity on kidney and cardiovascular health.

This study analyzes the effect of economic growth and income distribution on health inequality using data from the Organization for Economic Cooperation and Development (OECD). A panel analysis was conducted by combining 21 years of data (from 2000 to 2020) from 38 OECD countries. Life expectancy and avoidable mortality were set as the dependent variables; gross domestic product and poverty gap were set as the independent variables; body mass index, consumption, smoking rate, healthcare personnel, number of beds in health service facilities, national medical expenses, and unemployment were set as control variables. First, economic growth and poverty gap significantly affect life expectancy and avoidable mortality. It has been confirmed that to resolve health inequality, growth during growth and distribution must be prioritized. Second, it has been confirmed that as the poverty gap increases, life expectancy increases and the avoidable mortality rate decreases. A mechanism different from the existence of a medical security system targeting the lowest class or an increase in the welfare of society worked. In conclusion, as a policy proposal to alleviate health inequality, this study suggests that policy intervention is necessary to block or alleviate the negative impact of income inequality in health care policies.

The aim of this study was to evaluate the Hapo ms, a passive upper limbs exoskeleton developed to assist workers for tasks with arms in front of the body. Twelve participants had to perform a static task, a manual handling task and a load carrying task two times: with and without the exoskeleton. In all cases subjective (perceived effort in arm and back areas, comfort) and objective (muscular activity, postural balance) criteria were evaluated. Results have shown a decrease in anterior deltoid (-12 to -18% depending of the task) and in biceps brachii (-19% to -33% depending of the task) muscular activity. No significant difference was pointed out in back muscle and postural balance was not significantly perturbed due to the wear of the exoskeleton. Finally, perceived effort reduction was observed during the three tasks (except in back area for task 1). To conclude, the Hapo ms seems well adapted to assist upper arms during tasks with arms in front of the body.

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

The critical period (CP) phenomenon in language development ranks among the 125 conundrums facing scientists in the 21st century, according to Science. While the phenomenon itself has been noncontroversial in first language acquisition, it still warrants an adequate explanation. Predicated on language acquisition as a complex process, questions among the first to be raised include: How do children accomplish this remarkable feat in such a short amount of time? And how do nature and nurture come together to influence language learning? In second language acquisition, however, both the notion of CP, albeit popular, and its empirical evidence have remained contested to this date - among the questions, whether the observed evidence counts as CP-specific and/or whether or not it warrants an isomorphic attribution to maturational constraints. Entwined in this debate are two well-established facets of inter-learner differential attainment. The first is that there exists a stark difference in ultimate attainment between younger and older learners. A second facet is the vast differences in ultimate attainment among older learners. In this article, adopting a social physics approach, we mathematically establish both the relationship between nature and nurture contributions and the presence of a critical period, and, at once, tender a parsimonious and probable theory for the twin phenomena of inter-learner differential attainment.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Until now, crystalline NiCo2S4 and its composites have demonstrated improve performances in supercapacitor applications, compared to their oxide analogous, due to their relatively higher electrical conductivity, and multifaceted redox reaction. However, amorphous phase materials have recently shown promise in electrochemical energy storage systems. In this work, urea-assisted amorphous NiCo2S4 on nickel foam (referred to as aNCS) with high nitrogen atom% content, was obtained via hydrothermal method. In comparison to the crystalline NiCo2S4 (referred to as cNCS), aNCS exhibited superior electrochemical performance with specific capacitance of ~3506 F g-1 which is higher than cNCS specific capacitance of ~2185 F g-1 at 2 A g-1. Additionally, aNCS in two-electrode asymmetry supercapacitor exhibited specific capacitance and energy density of ~196 F g-1 and 56 Wh kg-1, respectively.

Radio-dynamic therapy (RDT), as an emerging cancer treatment method, has attracted attention due to its remarkable therapeutic efficacy using low-dose, high-energy radiation (such as X-rays), and has shown significant potential in cancer treatment. The RDT system typically consists of scintillators and photosensitizers. Scintillators absorb X-rays and convert them to visible light, activating nearby photosensitizers to generate cytotoxic reactive oxygen species (ROS). Challenges faced by the two-component strategy, including low loading capacity and inefficient energy transfer, hinder its final effectiveness. In addition, the tumor microenvironment (TME) with hypoxia and immunosuppression limits the efficacy of RDTs. Recent advances introduce one-component RDT systems based on nanomaterials with high-Z metal elements, which effectively inhibit deep-seated tumors. These novel RDT systems exhibit immune enhancement and immune memory, potentially eliminating both primary and metastatic tumors. This review comprehensively analyzes recent advances in the rational construction of RDTs, exploring their mechanisms and its application in the treatment of deep-seated tumors. Aimed at providing a practical resource for oncology researchers and practitioners, the review offers new perspectives for potential future directions in RDT research.

With the continuous improvement of people's quality of life and aesthetics, furniture products have higher requirements. Excellent solid wood chairs are the most representative products in furniture to enhance space and taste and whose design may significantly impact consumers' emo-tional experience and purchase decisions. This study aims to evaluate how the modeling imagery of solid wood chairs affects user preferences and emotional experiences. The development of the current era is inseparable from the analysis of big data. Firstly, a representative sample was ob-tained by multidimensional scaling (MDS), and the sample was analyzed and evaluated by fac-tor analysis. Moreover, five groups of adjective vocabulary were selected to describe the model-ing imagery of solid wood chairs, such as "balanced and coordinated", "unique and novel", "prac-tical and simple", "quality and detailed" and "traditional and plain". Further, the triangular fuzzy theory was applied to analyze and discuss the 12 types of solid wood chairs in the five groups of adjective vocabulary. Then the study verified that the differences in the evaluations of the 12 sam-ples in the "unique and novel" and "quality and detailed" groups were significant, but more minor differences in the groups of "traditional and plain", "balanced and coordinated" and "practical and simple". Through comprehensive comparison, five groups with similar modeling imagery were created, and solid wood chairs with different modeling imagery should be placed in suita-ble spaces. According to the results of this study, the evaluation of the modeling imagery of solid wood chairs can not only rely on subjective judgments but can be reasonably described through data analysis and mathematical algorithms. It can scientifically and effectively reflect the poten-tial perception needs of consumers on the modeling imagery of solid wood chairs, as well as help to improve the design efficiency of the furniture product development stage.

Since large articulated vehicles have uncertainties in trailer articulation angle as well as dynamic complexity, it is not easy to accurately establish a reliable motion plan. In this paper, two geometric path plans constructed based on the empirical rules of driving experts are presented so that articulated vehicles can automatically perform perpendicular parking on a reverse path. By analyzing the empirical parking methods of professional drivers, these path plans were constructed by appropriately combining several standardized simple basic motions to facilitate implementation in real vehicles. In addition, path plans included appropriate complementary motions to effectively respond to uncertainties arising from articulation angles, etc. The complementary motions developed in this study are based on the results of qualitative analysis on the behavior of articulated vehicles. The usefulness of the proposed articulated vehicle parking method has been proven through hundreds of experimental tests using a 1:10 ratio model automated vehicle.

Relationships between geoheritage and cultural heritage are increasingly becoming a topic of study, especially in urban contexts. Their integrated reading adds value for educational and urban geotourism purpose, being the latter an emerging sector of sustainable tourism. The case study of the monumental complex of San Francesco le Moniche, built in the ancient Norman county Aversa, in the northern Campania (Italy), is analyzed here. The cultural heritage of the monumental complex and the additional value associated with the natural heritage (geological and geomorphological context, building stones) have been linked. The building stratification of the complex has been read not only from documentary sources, but also from the distribution and architecture of the existing underground cavities, the building stones, from ancient images and even postcards, integrating disciplines such as geosciences, architecture, archaeology, speleology, engineering. The results provide a clear example of a geoheritage-cultural heritage interface and the importance of an integrated approach in the valorization of the cultural and natural heritage of urban areas. The results allowed us to improve the knowledge of the study site and provide useful tools for the planning of future targeted investigations.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

Ca-bentonite (CB) alone and in a mixture with limestone (L), tobacco biochar (TB) and zeolite (Z) on the fixation, geochemical fractions and absorption of Cd and Zn by Chinese cabbage in smelter heavily polluted (S-HP) and smelter low polluted (S-LP) soils were investigated. The results showed that the CB+TB and CB+L+TB treatments significantly immobilized Cd up to 22.03% and 29.68%, respectively, and reduced uptake by Chinese cabbage shoot to 35.98% with CB+Z+L and 61.35% with CB+L in S-HP and S-LP soils compared with the control. The CB+ Z+ L+TB treatment mobilized Cd up to 4.45% and increased absorption in the shoot by 9.85% in S-HP soil. The greatest immobilization of Zn was 53.18% and 58.20% with the CB+Z+L+TB treatment, which reduced Zn uptake in the plant shoot by 9.94% with CB + L and 58.04 with CB+Z+L+TB in S-HP and S-LP soils. The CB+Z+TB and CB+TB treatments mobilized Zn up to 35.40% and 4.80%, respectively, in both soils. Furthermore, the uptake of Zn in plant shoot was observed by 58.96% and 7.82% with application of CB+Z and CB+TB treatments, respectively, in S-HP and S-LP soils. Overall, our results suggest that Ca-bentonite alone and in mixtures with different amendments can be used to reduce the phyto-extraction of Cd and Zn in Zn-smelter polluted soils.

In this letter we investigate if SARS-CoV-2 RNA is involved in the increased ageing of alveolar cells. Our in silico study is explorative. With the results we are able to outline experiments with AEC2 repair of bleomycin damaged alveolar cells. If AEC2 repair capability is diminished by spike RNA then perhaps this result provides a first step on a route to treat immortal lung cancer cells.

CO₂ geological storage in deep saline aquifers was recently developed at industrial scale mainly in sandstone formations. Experiences on CO₂ injections in carbonates aquifers for permanent trapping are quite limited, mostly from US projects such as AEP Mountaineer, Michigan and Williston Basin. The behavior of fractures in carbonates plays a key role in those reservoirs in which porous matrix permeability is very poor, which drives the CO₂ plume migration through the fracture network where hydromechanics and geochemical effects take place due to injection. Hontomín (Spain) is the actual on-shore injection pilot in Europe (EP Resolution of 14 January 2014), whose reservoir is comprised of fractured carbonates. Existing experiences from field scale tests conducted on site have supported to better understand the behavior of this type of reservoirs for CO₂ geological storage. Innovative CO₂ injection strategies are being carried out in ENOS Project (EU H2020 Programme, http://www.enos-project.eu). First results based on field tests conducted at Hontomín, and the advanced modelling developed so far will be analyzed and discussed in this article, as well as, the description of future works. The evolution of operating parameters such as flow rate, pressure and recovery term during the tests confirm the CO₂ migration through the fractures.

A simple and sensitive liquid chromatography-tandem mass spectrometry (LC– MS/MS) method has been developed for the simultaneous determination of atorvastatin (ATOR), ezetimibe (EZM) and their three metabolites including o-hydroxyl atorvastatin (o-OH ATOR), p-hydroxyl atorvastatin (p-OH ATOR), and ezetimibe-glucuronide (EZM-G) in human plasma using benzyl paraben (BP) as internal standard (IS). The analytes and IS were ionized using ESI positive ion mode (ATOR, o-OH ATOR, and p-OH ATOR), ESI negative ion mode (EZM, EZM-G, and BP), and operated in multiple reaction monitoring (MRM) mode. They were next extracted by salting-out assisted liquid–liquid extraction with acetonitrile, and then analyzed by liquid chromatography on a reversed-phase chromatographic column (50 mm × 4.6 mm; 3.5 µm), using a mixture of ac-etonitrile and an acetic acid solution (0.5%) as the mobile phase, showing high extraction effi-ciency (>70%), and a minimized matrix effect. The method was satisfactorily validated, and showed excellent linearity over wide concentration ranges of 0.06–15 ng/mL, 0.6–150 ng/mL, 0.4–100 ng/mL, 0.12–30 ng/mL, and 0.05–3 ng/mL for EZM, EZM-G, ATOR, o-OH ATOR, and p-OH ATOR, respectively.

Lectins, characterized by their carbohydrate-binding ability, have an extensive practical application. However, their industrial use is limited by low yields, and few active recombinant lectins have been reported. In this study, the algal lectin BPL-3 (Bryopsis plumosa lectin 3) was successfully produced using a bacterial expression system, BL21(DE3), with an artificial repeated structure (dimeric construct). Recombinant dimeric BPL3 (rD2BPL3) was confirmed by LC-MS/MS spectrometry. Expression efficiency was greater for the construct with the repeat structure (rD2BPL3) than the monomeric form (rD1BPL3). Optimal conditions for expression were 1 mM IPTG at 20 °C. Recombinant lectin was purified under denaturing conditions and refolded by the flash dilution method. Recombinant BPL3 was solubilized in 1× PBS containing 2 M urea. rD2BPL3 showed strong hemagglutination activity using human erythrocytes, similar to that of native BPL3. rD2BPL3 had a similar sugar specificity to that of the native protein, i.e., to N-acetyl-glucosamine (GlcNAc) and N-acetyl-galactosamine (GalNAc). Glycan array results showed that recombinant BPL3 and native BPL3 exhibited different binding properties. Both showed weak binding activity to α-Man-Sp. Native BPL3 showed strong binding specificity to the alpha conformation of amino sugars, and rD2BPL3 had binding activity to the beta conformation. The process developed in this study was suitable for the quality-controlled production of high amounts of soluble recombinant lectins.

Frequently Asked Questions (FAQs) systems rely on semantic symmetry similarity measuring between two sentences. To address the challenges of insufficient training data and limited domain-specific understanding in low-resource FAQs, this paper proposes a general framework, PDAMF-FAQ, to solve these issues. Firstly, we propose a paraphrasing-based data augmentation model that integrates syntactic information and edit vectors. Using a rule-based approach, it retrieves template sentences from a corpus and masks relevant words with special characters. Edit vectors between the original and paraphrase sentences are added to a pre-trained model's encoding layer to enhance the model's ability to learn the differences between the original and reference paraphrase sentences. Additionally, this paper presents a mixed-feature semantic matching model based on SimBERT. The model extracts keyword features from the text, replacing these keywords with special characters to construct intent features. These intent features, along with the user question and keyword features, are then concatenated to form the model's input. Experiments were conducted respectively on the paraphrasing-based data augmentation model, mixed-feature semantic matching model and their comprehensive application in a low-resource domain-specific FAQ. The experimental results show that the proposed framework effectively improve the performance of domain-specific FAQ system.

We tested the use of mosquito traps as an alternative to insecticide spraying in Camargue (France) following the significant impacts observed on the non-target fauna through Bti persistence and trophic perturbations. In a village of 600 inhabitants, 16 Techno-Bam traps emitting CO₂ and using octenol lures were set from April to November 2016. Trap performance was estimated at 70% overall based on mosquito landing on human baits in areas with and without traps. Reduction of Ochlerotatus caspius and Oc. detritus, the two species targeted by Bti spraying, was respectively 74 and 98%. Traps were less efficient against Anopheles hyrcanus (46%), which was more attracted by lactic-acid than octenol lures based on previous tests. Nearly 300 000 mosquitoes from nine species were captured, with large variations among traps, emphasizing that trap performance is also influenced by surrounding factors. Environmental impact, based on the proportion of non-target insects captured, was mostly limited to small chironomids attracted by street lights. Breeding success of a house martin colony was not significantly affected by trap use, in contrast to Bti spraying. Our experiment confirms that deployment of mosquito traps can offer a cost-effective alternative to Bti spraying for protecting local populations from mosquito nuisance in sensitive natural areas.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

Wireless Sensor Networks are critical for modern applications ranging from environmental monitoring to smart city infrastructures. This research proposes a novel optimization learning and deployment strategy for Wireless Sensor Networks (WSNs) by 3D WUSN model is uniformly distributed M sensor nodes across diverse terrains, with clusters representing 20% of sensors, showcasing its ability to balance power consumption and extend network longevity, grounded in fuzzy clustering based protocol using the Fuzzy C-Means (FCM) method, called FCM-3DWUSN. Comparative analysis against established models including LEACH-C, K-Means and LEACH emphasized FCM-3DWUSN's outperformed performance, with average power consumption such as 134.990, 341.790, 143.895, and 192.984; respectively. The experimental result shows that FCM protocol in the 3D WUSN model can reduce energy consumption and improve the network lifetime to gather data and send the information.

This paper presents the latest developments in microCT, both globally and locally, for supporting the additive manufacturing industry. There are a number of recently developed capabilities which are especially relevant to the non-destructive quality inspection of additive manufactured parts; and also for advanced process optimization. These new capabilities are all locally available but not yet utilized to their full potential, most likely due to a lack of knowledge of these capabilities. The aim of this paper is therefore to fill this gap and provide an overview of these latest capabilities, showcasing numerous local examples.

The interaction between nanoparticles and cells has been studied extensively, but most research has focused on the effect of various nanoparticle characteristics, such as size, morphology, and surface charge, on the cellular uptake of nanoparticles. In contrast, there have been very few studies to assess the influence of cellular factors, such as growth factor responses, on the cellular uptake efficiency of nanoparticles. The aim of this study was to clarify the effects of epidermal growth factor (EGF) on the uptake efficiency of polystyrene nanoparticles (PS NPs) by A431 cells, a human carcinoma epithelial cell line. The results showed that EGF enhanced the uptake efficiency of A431 cells for PS NPs. In addition, inhibition and localization studies of PS NPs and EGF receptors (EGFRs) indicated that cellular uptake of PS NPs is related to the binding of EGF-EGFR complex and PS NPs. Different pathways are used to enter the cells depending on the presence or absence of EGF. In the presence of EGF, cellular uptake of PS NPs is via clathrin-mediated endocytosis, whereas in the absence of EGF, uptake of PS NPs does not involve clathrin-mediated endocytosis. Our findings indicate that EGF enhances cellular uptake of PS NPs by clathrin-mediated endocytosis. This result could be important for developing safe nanoparticles and their safe use in medical applications.

Introduction: SARS-CoV-2 infection was first reported in 2019 and has since spread throughout the world. This is a cross-sectional study in cooperation with 118 Department of Pre-Hospital and Territorial Emergency (118 SET) of Taranto City and the University of Bari, Aldo Moro, and the School of Medicine from Italy. We conducted a study on how the COVID-19 epidemics evolved and how it was contained by different countermeasures by taking into account data showing socio-demographic and that older persons, as well as individuals with comorbidities and poor metabolic health, and people coming from economically depressed areas with lower quality of life in general, are more likely to develop severe COVID-19 infection. Objective: Examine the association between county-level socio-demographic risk factors and COVID-19 incidence and mortality, determining the possible emo-biological markers, ferritin, and lymphocytes, that could be indicative of SARS-CoV-2 infection. Methods: Descriptive cross-sectional study on 600 patients examined and treated at general hospital Ninh Thuan from January to September 2022. Results: 33/600 patients were confirmed to be infected with SARS-CoV-2 (5.5%), males 4.8% and females 5.8%, the median age of infected patients is 36 years. Most infections were mild (75.8%). Our results revealed that the structure and the spatial arrangement of socio-demographic arrangements are important either as epidemiological determinants or as disease markers. Conclusion: Approximately 5.5% of patients infected with SARS-CoV-2 come to examination and treatment at the hospital, these findings suggested that possible infection rate in the burden of the COVID-19 pandemic, the sociodemographic risk factors, and their root causes must be addressed. In addition, lab results obtained from affected patients showed that lymphocytes and ferritin could be considered traits of mild COVID-19 infection.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

In addition to absorbing nitrogen from the soil, legumes have the ability to use atmospheric N2 through symbiotic nitrogen fixation. Therefore, legumes have developed mechanisms regulating nodulation in response to the amount of nitrate in the soil; in the presence of high nitrate concentrations, nodulation is inhibited while low nitrate concentrations stimulate nodulation and nitrogen fixation. This allows the legumes to switch from soil nitrogen acquisition to symbiotic nitrogen fixation. Recently, a particular interest has been given to the nitrate transporters, such as NPF or NRT2, having a role in the functioning of nodules. Nitrate transporters of the two model plants, Lotus japonicus and Medicago truncatula, shown to have a positive and/or a negative role in nodule functioning, depending on nitrate concentration, are presented in this review. Also, by exploiting available genomic and transcriptomic data in the literature we have identified the complete PsNPF family in Pisum sativum (69 sequences previously described and 21 new that we have annotated) and putative nitrate transporters candidate for playing a role in nodule functioning in P. sativum.

In this paper, we investigate the accuracy and robustness of three classes of methods for solving two-phase incompressible flows on a staggered grid. Here, the unsteady two-phase flow equations are simulated by finite volumes and penalty methods using implicit and monolithic approaches (such as the augmented Lagrangian and the fully coupled methods), where all velocity components and pressure variables are solved simultaneously (as opposed to segregated methods). The interface tracking is performed with a Volume-of-Fluid (VOF) method, using the Piecewise Linear Interface Construction (PLIC) technique. The home code Fugu is used for implementing the various methods. Our target application is the simulation of two-phase flows at high density and viscosity ratios, which are known to be challenging to simulate. The resulting strategies of monolithic approaches will be proven to be considerably better suited for these two-phase cases, they also allow to use larger time step than segregated methods.

Background. To describe the characteristics of anterior mediastinal masses on conventional magnetic resonance imaging (MRI) and to assess the role of the Apparent Diffusion Coefficient (ADC) value in distinguishing benign from malignant mediastinal lesions. Methods. We conducted a retrospective cross-sectional study on 55 patients with anterior mediastinal mass who performed MRI before treatment. Biopsy and histopathological assessments were done after that. A radiologist evaluates the changes of signal intensity on these sequences: T1- weighted VIBE DIXON pre and post-contrast with Gadolinium, T2 HASTE, T2 TIRM, DWI/ADC, to determine the size, margin of the lesion, the presence of fat, cystic in it. ADCs values were calculated from the ADC maps which were constructed from b = 0 and b = 2000 Results. The study was composed of 55 patients, with 5 benign lesions and 50 malignant lesions. The ADCmean, ADCmedian, ADC10, and ADC90 in the histogram-based approach and hot-spot-ROI-based mean ADC for the malignant lesions was significantly lower than those found in benign lesions (P-value <0.05). The hot-spot-ROI-based mean ADC had the highest value in differentiation between benign and malignant mediastinal lesions, between group A (benign lesions, thymoma A, AB, B1) and group B (thymoma B2, B3 and other malignant lesions). The cut-off point of the ADC value differentiating malignant from benign mediastinal lesions was 1,17x10-3mm2/s with sensitivity of 80%, and specificity of 80%. The cut off point of the ADC value differentiating group A from group B was 0.99 x10-3mm2/s with sensitivity of 78,4%, and specificity of 88.9%. The cut-off point of the ADC value differentiating lymphoma from other malignant lesions was 0,91 x10-3mm2/s with sensitivity of 100%, and specificity of 60.5%. Conclusion. Diffusion-weighted MRI and measurement of ADC value in histogram-based approach and hot-spot-ROI-based mean ADC are very helpful in the differentiation between benign and malignant anterior mediastinal lesions.