Sparse reward long horizon task is a major challenge for deep reinforcement learning algorithm. One of the key barriers is data-inefficiency. Even in the simulation environment, it usually takes weeks to training the agent. In this study, a data-efficiency training framework is proposed, where a curriculum learning is design for the agent in the simulation scenario. Different distributions of the initial state are set for the agent to get more informative reward during the whole training process. A fine-tuning of the parameters in the output layer of the neural network for value function is conduct to bridge the gap between sim-to-real. An experiment of UAV maneuver control is conducted in the proposed training framework to verify the method more efficient. We demonstrate that data-efficiency is different for the same data in different training stages.

Since the outbreak of 2019 novel coronavirus (2019-nCoV) at the hardest-hit city of Wuhan, the fast-moving spread has killed over three hundred people and infected more than ten thousands in China¹. There are more than one hundred cases outside of China, affecting a dozen of countries globally². The genome sequence of 2019-nCoV has been reported and fast diagnostic kits, effective treatment as well as preventive vaccines are rapidly being developed³. Initial fast-growing confirmed cases triggered lock-down of Wuhan as well as nearby cities in Hubei Province. Mathematical models have been proposed by scientists around the world to project the numbers of infected cases in the coming days ^4,5. However, major factors such as transportation and cultural customs have not been weighed enough. Our model is not set out for precise prediction of the number of infected cases, rather, it is meant for a glance of the dynamics under a public epidemic emergency situation and of different contributing factors. We hope that our model and simulation would provide more insights and perspective information to public health authorities around the globe for better informed prevention and containment solution.

The COVID19 coronavirus SARS-CoV2 spreading in Wuhan and now worldwide has been shown to use angiotensin-converting enzyme 2 ACE2 as its host cell receptor, like the severe acute respiratory syndrome coronavirus (SARS-CoV). Epidemiology studies found different sex and age groups have different susceptibility to infection, and very skewed severity and mortality of the virus infection, with male, old age, and comorbidity being the most inflicted. Here by analyzing GTEx and other public data in 30 tissues across thousands of individuals, we found significantly higher expression in Asian females compared to males and other ethnic groups, an age dependent ACE2 expression decrease and a highly significant decrease in type II diabetic patients. Consistently, the most significant expression quantitative loci (eQTLs) contributing to high ACE2 expression are close to 100% in East Asians, >30% higher than other ethnic groups. Together with the shockingly common enrichment of viral infection pathways among ACE2 anti-expressed genes, binding of virus infection-related transcription factors at ACE2 regulatory regions, the repression of ACE2 expression by inflammatory cytokines and by type 2 diabetes, and the induction by estrogen and androgen (both decrease with age) established a negative correlation between ACE2 expression and CovID19 fatality at both population and molecular levels. Our results will be instrumental when designing potential prevention and treatment strategies for ACE2 binding coronaviruses in general.

In this paper we investigate the differential topological properties of a subclass of singular space--subcarteisan spaces. First, we get further result on partition of unity for differential spaces. Second, we establish the tubular neighborhood theorem for subcartesian spaces with constant structural dimension. Third, we generalize the concept of Morse functions on smooth manifolds to differential spaces. For subcartesian space with constant structural dimension, we provide examples of Morse functions; With the assumption that the subcartesian space can be embedded as a bounded subset of an Euclidean space, we prove that smooth bounded functions on this space can be approximated by Morse functions; We study the infinitesimal stability of Morse functions on subcartesian spaces. Classical results on Morse functions on smooth manifolds can be treated directly as corollaries of our results here.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

Biotic and abiotic factors influence the formation of fungal-algal pairings in lichen symbiosis. It is poorly known which factors determine the specific associations, especially when distantly related fungi are considered. Here, we investigated the effect of different drivers on the association patterns of taxonomically diverse lichenized fungi and their trebouxioid symbiotic partners. In 200 samples collected across three biomes, we found 41 species of lichenized fungi, associating with 16 species of trebouxioid green algae, of which 62% were previously unreported. Species identity of the fungal and algal partner had the greatest effect on the outcome of the symbiosis compared with abiotic factors such as climatic variables and geographic distance. Partner specificity was found to be higher in tropical regions than in temperate and arctic regions. Co-phylogenetic analyses indicated congruent phylogenies of trebouxioid algae and associated fungi, rejecting their random associations. Evolutionary mechanisms contributing most to the observed phylogenetic patterns were ‘loss’ and ‘failure to diverge’ of the algal partners. This study broadens our knowledge of fungi-algae symbiotic patterns in view of Trebouxia-associated fungi.

With more companies entering the realm of electric vertical take-off and landing (eVTOL), and governments enacting policies to support the development of low-altitude economies, the commercial potential of eVTOL is being recognized by the public. However, true commercialization is still a long way off. This article analyzes the technologies, product features, potential markets, and government policies related to eVTOL, and constructs a four-stage, four-layer Policy-Technology Roadmap (P-TRM) model to guide the R&D process of eVTOL. Then transform it into a system structural model, and the Decision-making Trial and Evaluation Laboratory (DEMATEL) method is used to identify several key nodes in the R&D process. Utilizing the Technology Adoption Life Cycle (TALC) theory for interpretation and analysis, the article concludes by proposing strategies in product, technology, and policy support for how eVTOL can successfully cross the chasm. This preliminary analysis of the development path, key nodes, and necessary measures for crossing the chasm provides insights for the R&D and commercialization of eVTOL.

The so-called “Chinese pyramids” are huge burial mounds covering the tombs of the Emperors of the Western Han dynasty. If we include also the mounds of the members of the royal families, these monuments sum up to more than 40, scattered throughout the western and the southern outskirts of modern Xi'an. They are mostly unexcavated and poorly known although, taken together, they form a fascinating sacred landscape, which was conceived as a perennial witness of one of the most magnificent Chinese dynasties. This sacred landscape is today encroached by the frenetic urban development of the Xi’an urban area. We discuss and elaborate here some of the results of a recent, new satellite-imagery survey of these monuments, highlighting the aspects which may contribute to solutions for a sustainable and compatible development within this important ancient landscape.

Wool quality and yield are important economic traits of livestock. In this study, the skin tissues of the upper scapula of Super Merino sheep (SM) and Small-Tailed Han sheep (STH) during the growing period were studied. Differentially expressed (DE) long non-coding RNAs (lncRNAs) and messenger RNAs (mRNA) were identified via histopathological observation and high-throughput RNA sequencing. Gene ontology (GO) and the Kyoto Encyclopedia of Genes and Genomes (KEGG) were used to analyze differentially expressed genes. Reverse transcription quantitative Polymerase Chain Reaction (RT-qPCR) was used to verify nine selected DE lncRNAs and five DE mRNAs. Significant differences were found in the expression levels of LOC114113396 (KRTAP15-1), CRABP1, KRT10, KRTAP1-3, KRTAP4.3, KRT2, FGF1, IGF-1, and KIT in SM and STH skin tissues. These results indicate that these mRNAs may play an important role in the growth and development of hair follicles and the regulation of hair fiber traits. Differentially expressed lncRNA target genes and mRNAs were mainly enriched in biological processes and pathways related to skin development and fiber traits, which is consistent with previous studies. LncRNA MSTRG.9225.1, MSTRG.124320.1, MSTRG.96951.1, MSTRG.91685.1, MSTRG.122229.1, MSTRG.89255.1, MSTRG.98769.1, and MSTRG.84658.1 may indirectly participate in the growth and development of sheep hair follicles and the regulation of hair fiber diameter by regulating the expression of their respective target genes. These candidate lncRNAs and mRNAs may provide a basis for the study of sheep hair follicle growth and development and hair fiber traits.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

The aim of this paper is to compare the taxonomic composition and species diversity of the macrozoobenthos in Maritsa River (Bulgaria) and Han River (South Korea). Samples were collected at 15 selected sites in each river, including some of their main tributaries in 2020 and 2021. The number of the taxa recorded in Maritsa River was more than twice as great as in Han River: 192 taxa belonging to 19 systematic groups compared to 88 taxa belonging to 18 groups respectively. The order Ephemeroptera had the highest species richness: 31 taxa in the Bulgarian rivers and 26 taxa in the South Korean ones. The macrozoobenthic communities responded and adapted to the various conditions and impacts in the water environment with changes in the species composition and structure. The analysis of the similarity in the taxonomic composition showed low resemblance between all study sites but displayed distinct separations between the rivers and the two years. In general, the species structure of the macrozoobenthic communities in Maritsa River and its studied tributaries was better than in Han River. In both years, high species diversity was recorded at the reference sites in the rivers, characterized by conditions closely resembling natural environments. The species richness and the evenness of macrozoobenthos were very low at sites downstream subjected to considerable anthropogenic pressure. Some of the communities in Han River were almost destroyed completely.

The ADP-ribosylation factor 6 (Arf6), as the only member of the Arf family III protein, has been extensively studied for its diverse biological functions in animals. Previously, the Arf6 protein in Magnaporthe oryzae was found to be crucial for endocytosis and polarity establishment during asexual development. However, its role remains unclear in Sclerotinia sclerotiorum. Here, we identified and characterized SsArf6 in S. sclerotiorum using a reverse genetic approach. Deletion of SsArf6 impaired hyphal growth and development, and produced more branches. Interestingly, knockout of SsArf6 enhanced the tolerance of S. sclerotiorum to oxidative stress but the sensitivity to osmotic stress, and increased melanin accumulation, indicative of different roles of SsArf6 in various stress responses. Moreover, the appressorium formation was severely impaired, and fungal virulence to host plants was significantly reduced. Overall, our findings demonstrate the essential role of SsArf6 in hyphal development, stress responses, appressorium formation, and fungal virulence to host plants.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Green-space resources, in the context of urbanisation, cannot meet the actual needs of residents well, and the study of the balance of green-space resource allocation from the relationship between supply and demand is an urgent problem to be solved. This study quantitatively evaluates the green-space supply level from four dimensions by constructing a framework for assessment in the community life circle. It also evaluates the matching of green space supply and demand, resource distribution fairness, and distribution equilibrium under group differentiation through the supply–demand coupling matrix, Gini coefficient, and the Kruskal–Wallis H non-parametric rank-sum test, respectively. This study shows that (1) a significant spatial imbalance exists in green-space resource allocation in community life circles in different dimensions. (2) The comprehensive green-space supply level in the community life circle matched the total demand of residents to a low degree. (3) There was significant inequality in green-space resource allocation within the community life circle (the Gini coefficient of each evaluation perspective was > 0.4). Based on the study results, we were able to identify community life circles with spatial mismatches, different supply and demand, and other green-space resource allocation problems, which is of great significance to urban green-space research and planning practice under the "green justice" framework.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Mycophenolate mofetil was reported to have broad in vitro activity against different viruses and had been tried in combination with IFN-β in treating MERS infection. We tested the pharmacological activity of mycophenolate mofetil using SARS-CoV-2 infected Vero cells. The half-maximal effective concentration (EC₅₀) of mycophenolate mofetil against SARS-CoV-2 was 0.47 μM while that of remdesivir was 0.77 μM. Molecular docking results of mycophenolate mofetil to potential target proteins of COVID-19 suggested that mycophenolate mofetil might inhibit SARS-CoV-2 mainly by interacting with DHODH and IMPDH2. Furthermore, mycophenolate mofetil as an immunosuppressant may be a good therapeutic option for the management of hyperinflammation in patients with severe COVID-19. Based on its high potency against SARS-CoV-2 in Vero E6 cells, its good pharmacokinetics and clinical safety profile, mycophenolate mofetil deserves further exploration as potential treatment for COVID-19.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

ABSTRACT Background It is important to be able to predict, for each individual patient, the likelihood of later metastatic occurrence, because the prediction can guide treatment plans tailored to a specific patient to prevent metastasis and to help avoid under- or over-treatment. Deep Neural Network (DNN) learning, commonly referred to as deep learning, has become popular due to its success in image detection and prediction, but questions such as whether deep learning outperforms other machine learning methods when using non-image clinical data remain unanswered. Grid search has been introduced to deep learning hyperparameter tunning for the purpose of improving its prediction performance, but the effect of grid search on other machine learning methods are under-studied. In this research, we take the empirical approach to study the performance of deep learning and other machine learning methods when using non-image clinical data to predict the occurrence of breast cancer metastasis (BCM) 5, 10, or 15-years after the initial treatment. We developed DNN models as well as models using 9 other machine learning methods including Naive Bayes (NB), Logistic Regression (LR), Support Vector Machine (SVM), LASSO, Decision Tree (DT), k-Nearest Neighbors (KNN), Random Forrest (RF), AdaBoost (ADB), and XGBoost (XGB). We used grid search to tune hyperparameters for all methods. We then compared the deep learning models to the models trained using the 9 other machine learning methods. Results Based on the mean test AUC results, DNN ranks 6th, 4th, and 3rd when predicting 5-year, 10-year, and 15-year BCM respectively, out of 10 machine learning methods. The top performing methods in predicting 5-year BCM are XGB(1^st), RF(2^nd), and KNN(3^rd). For predicting 10-year BCM the top performers are XGB (1^st), RF(2^nd), and NB(3^rd) . Finally, for 15-year BCM the top performers are SVM (1^st), LR and LASSO (tied for 2^nd), and DNN (3^rd). The ensemble methods RF and XGB outperform other methods when data are less balanced, while SVM, LR, LASSO, and DNN outperform other methods when data are more balanced. Our statistical testing results show that at a significance level of 0.05 DNN overall performs no worse than other machine learning methods when predicting 5-year, 10-year, and 15-year BCM. Conclusions Our results show that deep learning with grid search overall performs at least as well as other machine learning methods when using non-image clinical data. It is interesting to note that some of the other machine learning methods such as XGB, RF, and SVM are very strong competitors of DNN when incorporating grid search. It is also worth noting that the computation time required to do grid search with DNN is way more than that required to do grid search with the other 9 machine learning methods.

Litsea cubeba, an important medicinal plant, is widely used as traditional Chinese medicine and spice. Using cytotoxicity-guided fractionation, nine new lignans (1-9) and eleven known analogues (10-19) were obtained from the EtOH extract of the twigs of L. cubeba. Their structures were assigned by extensive 1D and 2D NMR experiments, and the absolute configurations were resolved by specific rotation and a combination of experimental and theoretically calculated electronic circular dichroism (ECD) spectra. In the cytotoxicity assay, 7',9-epoxylignans with feruloyl or cinnamoyl group (7-9, 13 and 14) were selectively cytotoxic against NCI-H1650 cell line, while the dibenzylbutyrolactone lignans (17-19) exerted cytotoxicities against HCT-116 and A2780 cell lines. The results highlighted the structure-activity relationship importance of a feruloyl or a cinnamoyl moiety at C-9′ or/and C-7 ketone in 7',9-epoxylignans. Furthermore, compound 11 was moderate active toward protein tyrosine phosphatase 1B (PTP1B) with an IC50 value of 13.5 μM, and compounds 4-6, 11 and 12 displayed inhibitions against LPS-induced NO production in RAW264.7 macrophages, with IC50 values of 46.8, 50.1, 58.6, 47.5, and 66.5 μM, respectively.

The astro-structures with the shape of comet and semi-circle, are found in the electronegative inductively coupled plasmas (ICPs), e.g., Ar/O2 and Ar/SF6. They are formed by means of the self-coagulation theory. This theory is built and based on two-dimensional fluid model simulation dynamic data of the above ICP sources. Concretely, quasi-Helmholtz equation is constructed through the free diffusion transport component and a novel negative chemical source term. The absolute value of recombination rate is higher than the attachment rate and so the net source of simulated anion is negative. This is quite a new chemical phenomenon in the electronegative and gaseous discharging plasmas when compared to the previously reported normal positive chemical source that will generate ambi-polar diffusion potential. In electronegative plasma, the self-coagulation is ambi-polar to sustain the electrical neutrality. Besides, when the anions are accelerated by ambi-polar potential before self-coagulated, the self-coagulation is again advective which leads to the formation of blue sheath. At the ambi-polar self-coagulation of high electronegativity, the electrons dynamics are relatively decoupled from ions and meanwhile they have their own relatively weak, spontaneous, and monopolar self-coagulation in the periphery of astro-structure. At the ambi-polar self-coagulation, both the anion and cation are individually treated as mass point models that carry charge (point charge models, more precisely). When the charge amounts of two individual astr-structures, e.g., semi-circle SF3+ and Ar+, are equal, the coagulated profile of heavy species SF3+ collapses by the expelling effect of Coulomb force that exists between the two point-charges. This is an anti-collective behavior of astro-structure, instead of the collective interaction of plasma, since the collapse of coagulated heavy species creates spatially dispersed charge density that cannot be shielded. The simulation shows that the lighter the species, the easier it self-coagulates, determined by the inertial effect of density quantity. The discharge picture of electronegative plasma is combined by a dynamic continuum transport (e.g., forming the ellipse background) and the mechanical balance contained in the static self-coagulation process (proven by dimensional analysis of continuity equation). The popular astro-structure of electronegative ICP source awaits urgently for the validation of experiment.

This paper presents the findings of an exploratory study on the continuously generating Big Data on Twitter related to the sharing of information, news, views, opinions, ideas, knowledge, feedback, and experiences about the COVID-19 pandemic, with a specific focus on the Omicron variant, which is the globally dominant variant of SARS-CoV-2 at this time. A total of 12028 tweets about the Omicron variant were studied, and the specific characteristics of tweets that were analyzed include - sentiment, language, source, type, and embedded URLs. The findings of this study are manifold. First, from sentiment analysis, it was observed that 50.5% of tweets had the ‘neutral’ emotion. The other emotions - ‘bad’, ‘good’, ‘terrible’, and ‘great’ were found in 15.6%, 14.0%, 12.5%, and 7.5% of the tweets, respectively. Second, the findings of language interpretation showed that 65.9% of the tweets were posted in English. It was followed by Spanish or Castillian, French, Italian, Japanese, and other languages, which were found in 10.5%, 5.1%, 3.3%, 2.5%, and <2% of the tweets, respectively. Third, the findings from source tracking showed that “Twitter for Android” was associated with 35.2% of tweets. It was followed by “Twitter Web App”, “Twitter for iPhone”, “Twitter for iPad”, “TweetDeck”, and all other sources that accounted for 29.2%, 25.8%, 3.8%, 1.6%, and <1% of the tweets, respectively. Fourth, studying the type of tweets revealed that retweets accounted for 60.8% of the tweets, it was followed by original tweets and replies that accounted for 19.8% and 19.4% of the tweets, respectively. Fifth, in terms of embedded URL analysis, the most common domains embedded in the tweets were found to be twitter.com, which was followed by biorxiv.org, nature.com, wapo.st, nzherald.co.nz, recvprofits.com, science.org, and other URLs. Finally, to support similar research and development in this field centered around the analysis of tweets, we have developed an open-access Twitter dataset that comprises tweets about the SARS-CoV-2 omicron variant since the first detected case of this variant on November 24, 2021.

Energy Measurement and Verification (M&V) aims to make inferences about the savings achieved in energy projects, given the data and other information at hand. Traditionally, a frequentist approach has been used to quantify these savings and their associated uncertainties. We demonstrate that the Bayesian paradigm is an intuitive, coherent, and powerful alternative framework within which M&V can be done. Its advantages and limitations are discussed, and two examples from the industry-standard International Performance Measurement and Verification Protocol (IPMVP) are solved using the framework. Bayesian analysis is shown to describe the problem more thoroughly and yield richer information and uncertainty quantification than the standard methods while not sacrificing model simplicity. We also show that Bayesian methods can be more robust to outliers. Bayesian alternatives to standard M&V methods are listed, and examples from literature are cited.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Forest ecosystems make a greater contribution to carbon (C) stocks than any other terrestrial ecosystem. To understand the role of regional forest ecosystems in global climate change and carbon exchange, forest C stock and its spatial distribution within the small (2,300 km2) Liuxihe River basin were analyzed to determine the different contributors to the C stock. Forest C stocks were quantified by measuring the biomass of trees, understory vegetation, litter and roots, as well as soil organic C, using data from field samples and laboratory experiments. The results showed that forests stored 38.04 Tg C in the entire basin, with secondary and planted forests accounting for 89.82% and 10.18%, respectively, of the stored C. Five types of forests, a subtropical evergreen broad-leaved forest, a subtropical coniferous and broad-leaved mixed forest, a subtropical coniferous forest, a timber forest, and a non-wood forest, stored 257.55 ± 15.01, 218.92 ± 9.59, 195.24 ± 18.29, 177.42 ± 17.55, and 117.86 ± 6.04 Mg C ha−1, respectively. In the forest ecosystem C stocks of the basin, soils averagely contribute about 73.78%, not including root underground biomass. It provides a comprehensive method for forest ecosystem carbon investigation and forest management in small basin scale.

Microcystis aeruginosa is a common cyanobacteria found in water blooms and often causes ecological harm. Antibiotics are also increasingly used for the prevention and treatment of bacterial infections in aquaculture. However, since most antibiotics cannot be fully metabolized, they enter the water environment and cause ecological impacts. In this paper, the effects of the two quinolone antibiotics (enrofloxacin and ciprofloxacin) on the population density and microcystins (MCs) production of Microcystis aeruginosa were studied. It is of great significance for the ecological risk assessment of antibiotics to the water environment. The results showed that the 96h EC50 values of enrofloxacin and ciprofloxacin to Microcystis aeruginosa were 56.10mg/L and 49.80mg/L respectively, and the toxicity of ciprofloxacin to Microcystis aeruginosa was slightly stronger than that of enrofloxacin. With the increase of the two quinolone antibiotic concentration, the growth inhibition rate (IR) increased, but when the concentration reached a certain height, the IR would reach its threshold. Long-term exposure to low concentrations of these two quinolone antibiotics is not only more likely to lead to the outbreak of Microcystis aeruginosa, but also increase its toxin production capacity. The highest contents of MCs in enrofloxacin and ciprofloxacin groups were 95.539 μg/g and 93.720 μg/g, respectively. The MCs value of these three enrofloxacin treatment groups was more than above 51.8 times that of control group (CK) on the 4th day; from 8th day to 14th day, the MCs value of these three enrofloxacin treatment groups was more than above 3.2 times that of CK group. For another ciprofloxacin, the MCs value of the treatment group was more than 64.98 times that of the CK group on the 4th day, and from 8th day to 14th day, the MCs value of the treatment group was more than 2.7 times that of the CK group. These findings provide crucial management rationale.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

The dynamic factors in the environment violate the static environment assumption of the SLAM algorithm, leading to a decrease in the accuracy of camera positioning. In recent years, many studies have attempted to address dynamic objects by combining semantic constraints and geometric constraints, but issues such as poor real-time performance, the potential for mistakenly treating humans as rigid objects, and subpar performance in high-dynamic scenes still persist. This paper proposes a dynamic scene visual SLAM algorithm called Dynamic SLAM based on target tracking and multi-view geometry (TKG-SLAM), based on object detection, Kalman filters, and multi-view geometry. This algorithm takes into consideration both real-time performance and algorithm accuracy. It combines semantic constraints and multi-view geometry constraints, selectively running the algorithm in different scenarios, filtering and preserving static points for camera pose estimation. Experimental results demonstrate that, compared to current state-of-the-art dynamic SLAM methods, our approach achieves optimal performance in some scenarios and exhibits stronger real-time capabilities.

The Asian hornet, Vespa velutina, is an invasive species that has not only expanded its range in Asia but also invaded European countries, incurring significant costs on the local honey and bee industry. This phylogeographic study aims to trace the evolutionary trajectory of V. velutina and its close relatives, aiming to identify features that characterize an invasive species. The last successful invasion of Vespa velutina into France occurred in 2002.40, and into South Korea in 2002.77, estimated by fitting a logistic equation to the number of observations over time. The instantaneous rate of increase is 1.3667 for V. velutina in France and 0.2812 in South Korea, consistent with the interpretation of little competition in France and strong competition from local hornet species in South Korea. The invasive potential of two sister lineages can be compared by their distribution area when proper statistical adjustments are made to account for differences in sample size. V. velutina has a greater invasive potential than its sister lineage. The ancestor of V. velutina split into two lineages, one found in Indonesia/Malaysia and the other colonizing the Asian continent. The second lineage split into a sedentary clade inhabiting Pakistan and India, and an invasive lineage colonizing much of Southeast Asia. This latter lineage gave rise to subspecies V. v. nigrithorax that invaded France, South Korea, and Japan. My software PGT, which generates geophylogenies and computes geographic areas for individual taxa, is useful for understanding biogeography in general and invasive species in particular. I discussed the conceptual formulation of an index of invasiveness for comparison between sister lineages.

ABSTRACT Background Ubiquitination plays an important role in protein post-translational processes and has been found to be involved in a number of regulatory functions including proteasome degradation, DNA repair, transcription, signal transduction, endocytosis, and sorting. As the identification of ubiquitination site is critical to furthering our understanding of the mechanism of ubiquitination, various experimental and machine learning methods have been used to conduct this task. It has been an important but challenging task to improve the accuracy of ubiquitination site prediction. In this research, we explore the possibility of improving the prediction performance of machine learning by incorporating grid search in the training process. Method We developed grid search procedures for each of six widely used machine learning methods including NB, LR, DT, SVM, LASSO, and KNN, and applied them to ubiquitination site prediction using the six PCP datasets that were previously developed. For each of the ML methods, we developed a set of values for each of the tunable hyperparameters available to the method. These sets of values then can be combined to form a large grid of hyperparameter settings, and each of these settings is used in the grid search. We integrated 5-fold cross-validation in grid search to train and test ML models and applied an additional independent validation procedure by conducting a pre-training 80-20 sample split. We evaluated the performance of the six methods by comparing them side by side for each of the six datasets. We also compared the grid search results with the results that were previously published without doing grid search. To optimize the prediction performance, we trained 1.1 million ML models in total through grid search. Results We compared the overall prediction performance of these six methods, as well as their prediction performance when working with balanced vs. imbalanced data, and large-scale vs. small-scale data. From the perspective of dataset, we find that the overall performance of every PCP dataset has been significantly improved in this study compared to the previous study, with the percentage increase of the average AUC of all six datasets ranging from 7.9% (PCP-4) up to 17.0% (PCP-1). From the perspective of method, we find that three out of four methods significantly benefit from grid search comparing to their previously published non-grid search results, with the maximum AUC improvement as high as 47% (LASSO on PCP-5), 43.3% (NB on PCP-1), and 33.7% (SVM on PCP-6). SVM overall ranks number one, followed by KNN as the number two performer based on their average AUCs on all datasets. But these two also ranked the top two (KNN 76 days and SVM 15 days) in terms of the total running time that they need to do grid search. We also find that SVM, KNN, and DT tend to handle small-scale and imbalanced datasets better, while LR, and LASSO are doing well with large-scale and balanced datasets. NB is more sensitive to data imbalance while less sensitive to the size of a dataset. Conclusions Our results show that using grid search has improved the performance of ubiquitination prediction significantly. We find that the performance of a method is closely related to its hyperparameter setting and the type of data it handles. Even though SVM is on average an outperformer, none of the methods can provide the best performance for all datasets. When sufficient computing resources are well accessible, grid search is an effective way to identify both a top performing model for a machine learning method and a suitable machine learning method for a particular dataset.

Permanent magnet brushless DC motor (BLDCM) is usually controlled by six step commutation method, and flux-weakening method is used to make the motor run higher above the base speed. For now, it is considered that the weak magneto-electric angle range is 0-pi/3, and that of deep weakening is pi/3-pi/2. In the field- weakening control, the forward shift of commutation point will form inverter circulating current in the three-phase bridge of inverter and the stator winding of the motor. In this paper, the principle of inverter circulating current formed by inverter is analyzed. Through magnetic potential analysis and Simulink simulation, it is concluded that flux-weakening control will generate inverter circulating current in the inverter and motor stator winding. The inverter circulating current affects the magnetic potential of motor, and magnetic potential will move to the rotating direction of motor rotor. When the forward shift angle of inverter commutation point is 0-pi/6 electrical angle, the movement amplitude of current circulating current of inverter is less than pi/6, which plays the role of weakening magnetic field and driving effect; when the forward moving angle is pi/6-pi/3, the movement amplitude of inverter circulating current exceeds pi/6, which plays the role of magnetic weakening and braking. When the braking effect occurs, the reverse torque will appear, resulting in the decrease of motor torque and efficiency. Therefore, the range of weak magneto-electric angle should be between 0-pi/6.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Real estate industry is related to the national economy and people's livelihood，characterized by a high degree of financial intensity. The enterprises in this industry need certain financial ability and large shareholder controlling ability to support their survival. However，due to the multiple adverse impacts of current state policies，banks and private capital，the credit crunch，the sudden decrease in withdrawn funds and the limitation of internal financing，the problem of capital restraint of real estate enterprises has become more and more serious. From the perspective of corporate governance，this paper studies the interaction among financial constraints，ownership concentration and corporate performance under different shareholding states by analyzing the quantitative characteristics of equity structure，and looks for the appropriate range of the largest shareholder holding ratio，which has considered the financial performance and risk. It is found that raising the ownership concentration can effectively ease the financing constraints and improve the performance of enterprises，both of which are significant under the state of high ownership concentration， while the financial constraints play a significant intermediary effect under the State of absolute holding， while in the decentralized state of ownership，there is a significant regulatory effect，and the interaction of the three will be different due to the size of the enterprise.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

Aim: We estimated the correlation between serum bilirubin concentrations and insulin resistance in advanced maternal age without diabetes mellitus. Method: The cross-sectional study involved consecutive 50 women of advanced maternal age without diabetes mellitus, and insulin resistance (IR) was diagnosed according to the homeostatic model assessment insulin resistant (HOMA-IR) formula and the cut-off point was set to more than 2.5. Serum bilirubin and HOMA-IR were compared between the IR (+) and IR (-) groups. Results: We found that serum bilirubin levels in the IR subjects were significantly decreased compared to those without IR (p = 0.0252). Serum bilirubin concentrations were negatively correlated with the weight and the fasting insulin concentrations in all subjects (r=−0.282, p=0.047, r=-0.424, p=0.002). Additionally, serum bilirubin had a negatively correlation with HOMA-IR (r = -0.410, p = 0.003) in all subjects. The multiple linear regression analysis found that serum total bilirubin levels were independently correlated with HOMA-IR (beta = -0.392, p= 0.015) in these subjects. Conclusions: The study demonstrated that serum bilirubin concentrations had negatively correlation with insulin resistance in advanced pregnant women without diabetes mellitus, and decreased serum bilirubin may forebode increased gestational diabetes mellitus risk in our study population.

This study analyzes the effect of economic growth and income distribution on health inequality using data from the Organization for Economic Cooperation and Development (OECD). A panel analysis was conducted by combining 21 years of data (from 2000 to 2020) from 38 OECD countries. Life expectancy and avoidable mortality were set as the dependent variables; gross domestic product and poverty gap were set as the independent variables; body mass index, consumption, smoking rate, healthcare personnel, number of beds in health service facilities, national medical expenses, and unemployment were set as control variables. First, economic growth and poverty gap significantly affect life expectancy and avoidable mortality. It has been confirmed that to resolve health inequality, growth during growth and distribution must be prioritized. Second, it has been confirmed that as the poverty gap increases, life expectancy increases and the avoidable mortality rate decreases. A mechanism different from the existence of a medical security system targeting the lowest class or an increase in the welfare of society worked. In conclusion, as a policy proposal to alleviate health inequality, this study suggests that policy intervention is necessary to block or alleviate the negative impact of income inequality in health care policies.

Background: With the trend of intelligent display, the interface design of in-vehicle HUD is an expanding research field; Methods: To solve the subjectivity and uncertainty in the optimization of HUD interface design schemes, this paper proposed a hybrid scheme evaluation and optimization method based on entropy weight and VIKOR. The entropy weight method was used to reduce the subjectivity the decision-maker's weighting and obtain the objective weight of each indicator; The VIKOR method was used to obtain the best ranking of alternative schemes, and then the optimal interface design scheme was selected; Results: The evaluation of in-vehicle HUD interface design schemes were taken as an example for verification and calculation. The results showed that this method considers the subjectivity and uncertainty of the decision-making process in the optimization of design scheme, which can effectively improve the objectivity and accuracy of the evaluation results, and provide a reference for designers to optimize interface design schemes.

Water resources are threatened nowadays by pollution that comes from domestic, industrial and agricultural discharges without prior treatment. This pollution causes the degradation of water quality. Surface pollutants can seep through the soil into water tables. The objective of our work is to assess and control the physicochemical quality of the Chari Baguirmi groundwater, to protect human health. The quality of 83 boreholes was assessed, while performing analysis for 12 physicochemical parameters at the National Water Laboratory and at the Center for Quality Control of Foodstuffs in Chad. These parameters are: pH, EC, Ca2+, Mg2+, Na+, K+, Cl-, SO42-, NH4+ and NO3- , Fe2+ and HCO3-. Also, the results obtained were compared with WHO standards. The geochemical statistical approach has made it possible to characterize the hydro geochemical properties and to understand the major processes of the mineralization of groundwater resources in Chari Baguirmi region in Chad. Some of its waters are acidic and weakly mineralized, rich in Fe2+ and NH4+. The origin of the mineralization is due to the alteration of the host rocks and to the hydrolysis of silicate and ferromagnesian minerals as well as anthropogenic pollution. The ammonium concentrations in N’Djamena boreholes are higher than WHO standards, indicating the presence of pollution which may come from organic waste. These results constitute a preliminary step in understanding hydro geochemical functioning and a basis for monitoring the physicochemical quality of the water in the study area.

Asian giant hornet, Vespa mandarinia, is an invasive species that could potentially destroy local honeybee industry in North America. It has been observed to nest in the coastal regions of British Columbia in Canada and Washington State in USA. What is the source population of the immigrant hornets? The identification of the source population can not only shed light on the route of immigration, but also on the similarity between the native habitat and the potential new habitat in the Pacific Northwest. We analyzed mitochondrial COX1 sequences of specimens sampled from multiple populations in China, South Korea, Japan and the Russian Far East. V. mandarinia exhibits phylogeographic patterns, forming monophyletic clades for 16 specimens from China, six specimens from South Korea and two specimens from Japan. The two mitochondrial COX1 sequences from Nanaimo, British Columbia are identical to the two sequences from Japan. The COX1 sequence from Blaine, Washington State, clustered with those from South Korea, and is identical to one sequence from South Korea (GenBank accession MN716828). Our geophylogeny, which allows visualization of genetic variation over time and space, provides evolutionary insights on the evolution and speciation of three closely related vespine species (V. tropica, V. soror and V. mandarinia). The geophylogeny also highlights a strong insufficiency in sample collection in China. The existing sequenced specimens from mainland China with geographic coordinates were represent only four provinces, missing populations along the coastal regions in East China. One therefore cannot exclude the possibility that the Asian giant hornet found in Canada and USA may also be identical to V. mandarinia in Eastern China. We strongly recommend more extensive DNA barcoding data with geographic information and longer DNA barcode (e.g., the entire mitochondrial genome) so that critical questions on invasive species and environmental conservation can be addressed more accurately than what is possible with existing data.

Aiming at the problem of hypersonic morphing vehicle avoiding no-fly zones and reaching the target, an improved predictor-corrector guidance method is proposed. Firstly, the aircraft motion model and the constraint model are established. Then, the basic algorithm is given, the Q-learning method is used to design the attack angle and sweep angle scheme to ensure that the aircraft can fly over the low-altitude zones. The B-spline curve is used to design the location of flight path points and the bank angle scheme is designed according to the predictor-corrector method, so that the aircraft can fly around to avoid high-altitude zones. Next, Monte Carlo reinforcement learning(MCRL) method is used to improve predictor-corrector method and Deep Neural Network(DNN) is used to fit reward function. The improved method can generate trajectory with better performance. Simulation results verify the effectiveness of the proposed algorithm.

Natural disasters are showing an increase in the magnitude, frequency, and geographic distribution. Studies have shown that individuals’ self-sufficiency, which largely depends on household preparedness, is very important for hazard mitigation in at least the first 72 hours following a disaster. However, for factors that influence a household’s disaster preparedness, though there are many studies trying to identify from different aspects, we still lack an integrative analysis on how these factors contribute to a household’s preparation. This paper aims to build a classification model to predict whether a household has prepared for a potential disaster based on their personal characteristics and the environment they located. We collect data from the Federal Emergency Management Agency’s National Household Survey in 2018 and train four classification models - logistic regression, decision trees, support vector machines, and multi-layer perceptron classifier models- to predict the impact of personal characteristics and the environment they located on household prepare for the potential natural disaster. Results show that the multi-layer perceptron classifier model outperforms others with the highest scoring on both recall (0.8531) and f1 measure (0.7386). In addition, feature selection results also show that among other factors, a household’s accessibility to disaster-related information is the most critical factor that impacts household disaster preparation. Though there is still room for further parameter optimization, the model gives a clue that we could support disaster management by gathering publicly accessible data.

In this paper, a class of nonlinear ordinary differential equations with impulses at variable times is considered. The existence and uniqueness of solution are given. At the same time, modifying the classical definitions of continuous dependence and Ga^teaux differentiability, some results on continuous dependence and Ga^teaux differentiable of solution relative to the initial value also are presented in new topology sense. For the autonomous impulsive system, the periodicity of solution is given. As an application, properties of solution for a type of controlled nonlinear ordinary differential equation with impulses at variable times is obtained. These results are foundation to study optimal control problems of systems governed by the differential equations with impulses at variable times.

The critical period (CP) phenomenon in language development ranks among the 125 conundrums facing scientists in the 21st century, according to Science. While the phenomenon itself has been noncontroversial in first language acquisition, it still warrants an adequate explanation. Predicated on language acquisition as a complex process, questions among the first to be raised include: How do children accomplish this remarkable feat in such a short amount of time? And how do nature and nurture come together to influence language learning? In second language acquisition, however, both the notion of CP, albeit popular, and its empirical evidence have remained contested to this date - among the questions, whether the observed evidence counts as CP-specific and/or whether or not it warrants an isomorphic attribution to maturational constraints. Entwined in this debate are two well-established facets of inter-learner differential attainment. The first is that there exists a stark difference in ultimate attainment between younger and older learners. A second facet is the vast differences in ultimate attainment among older learners. In this article, adopting a social physics approach, we mathematically establish both the relationship between nature and nurture contributions and the presence of a critical period, and, at once, tender a parsimonious and probable theory for the twin phenomena of inter-learner differential attainment.

The rapid development of the Industrial Internet of Things (IIoT) has brought enormous opportunities to the industrial environment but has also posed significant challenges to network security, especially the physical layer security challenges,which is crucial for the reliable transmission of messages interconnected devices and sensors. Focus on the enhancing the physical layer security in the IIoT communication, this paper proposed a mechanism of Spatial Secrecy Outage Probability (SSOP) to ensure the secure transmission of data. The SSOP algorithm assumes that the location of legitimate device is known, while eavesdropper on the random distribution of device locations, forming the SSOP model related to device locations from the perspective of insecure regions (ISR) and secure regions (SR), and deduce the closed-form expression for its upper bound. Subsequently under the constraint of SSOP conditions, establish an optimization model with the objective of system throughput maximization based on Spatial Secrecy Outage Probability(SRM-SSOP). By optimizing the transmission rate of legitimate channels or controlling the transmission power, the maximization of system throughput can be achieved, thus reducing the consumption of communication resources. Through sophisticated modeling and simulation in the MATLAB, we verified the accuracy of the definition and derived upper bound of SSOP. The experimental results also show that SSOP algorithm gradually converges to a specific value as the number of antenna elements increases. In addition, we observed that when the receiver device is aligned with the normal direction of the transmit antenna array, the SSOP reaches a minimum value. These performance are crucial for understanding and optimizing the security performance of IIoT communication systems.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Sedimentary microfacies division is the basis of oil and gas exploration research. The traditional sedimentary microfacies division mainly depends on human experience, which is greatly influenced by human factor and is low in efficiency. Although deep learning has its advantage in solving complex nonlinear problems, there is no effective deep learning method to solve sedimentary microfacies division so far. Therefore, this paper proposes a deep learning method based on DMC-BiLSTM for intelligent division of well-logging—sedimentary microfacies. First, the original curve is reconstructed multi-dimensionally by trend decomposition and median filtering, and spatio-temporal correlation clustering features are extracted from the reconstructed matrix by Kmeans. Then, taking reconstructed features, original curve features and clustering features as input, the prediction types of sedimentary microfacies at current depth are obtained based on BiLSTM. Experimental results show that this method can effectively classify sedimentary microfacies with its recognition efficiency reaching 96.84%.

Sclerotinia sclerotiorum is a devastating fungal pathogen that causes severe crop losses worldwide. It is of vital importance to understand its pathogenic mechanism for disease control. Through a forward genetic screen combined with next-generation sequencing, a putative protein kinase, SsCak1, was found to be involved in growth and pathogenicity of S. sclerotiorum. Knockout and complementation experiments confirmed that deletions in SsCAK1 caused defects in mycelium and sclerotia development, as well as appressoria formation and host penetration, leading to complete loss of virulence. These findings suggest that SsCak1 is essential for growth, development and pathogenicity of S. sclerotiorum. Therefore, SsCak1 could serve as a potential target for the control of S. sclerotiorum infection through host-induced gene silencing (HIGS), which could increase crop resistance to the pathogen.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Until now, crystalline NiCo2S4 and its composites have demonstrated improve performances in supercapacitor applications, compared to their oxide analogous, due to their relatively higher electrical conductivity, and multifaceted redox reaction. However, amorphous phase materials have recently shown promise in electrochemical energy storage systems. In this work, urea-assisted amorphous NiCo2S4 on nickel foam (referred to as aNCS) with high nitrogen atom% content, was obtained via hydrothermal method. In comparison to the crystalline NiCo2S4 (referred to as cNCS), aNCS exhibited superior electrochemical performance with specific capacitance of ~3506 F g-1 which is higher than cNCS specific capacitance of ~2185 F g-1 at 2 A g-1. Additionally, aNCS in two-electrode asymmetry supercapacitor exhibited specific capacitance and energy density of ~196 F g-1 and 56 Wh kg-1, respectively.

Radio-dynamic therapy (RDT), as an emerging cancer treatment method, has attracted attention due to its remarkable therapeutic efficacy using low-dose, high-energy radiation (such as X-rays), and has shown significant potential in cancer treatment. The RDT system typically consists of scintillators and photosensitizers. Scintillators absorb X-rays and convert them to visible light, activating nearby photosensitizers to generate cytotoxic reactive oxygen species (ROS). Challenges faced by the two-component strategy, including low loading capacity and inefficient energy transfer, hinder its final effectiveness. In addition, the tumor microenvironment (TME) with hypoxia and immunosuppression limits the efficacy of RDTs. Recent advances introduce one-component RDT systems based on nanomaterials with high-Z metal elements, which effectively inhibit deep-seated tumors. These novel RDT systems exhibit immune enhancement and immune memory, potentially eliminating both primary and metastatic tumors. This review comprehensively analyzes recent advances in the rational construction of RDTs, exploring their mechanisms and its application in the treatment of deep-seated tumors. Aimed at providing a practical resource for oncology researchers and practitioners, the review offers new perspectives for potential future directions in RDT research.

There is a growing consensus that culture influences the perception of facial expressions of emotion. However, little is known about whether and how culture shapes the production of emotional facial expressions, and even less so about whether culture differentially shapes the production of posed versus spontaneous expressions. Drawing on prior work on cultural differences in emotional communication, we tested the prediction that people from the Netherlands (a historically heterogeneous culture where people are prone to low-context communication) produce facial expressions that are more distinct across emotions compared to people from China (a historically homogeneous culture where people are prone to high-context communication). Furthermore, we examined whether the degree of distinctiveness varies across posed and spontaneous expressions. Dutch and Chinese participants were instructed to either pose facial expressions of anger and disgust, or to share autobiographical events that elicited spontaneous expressions of anger or disgust. Using the complementary approaches of supervised machine learning and information-theoretic analysis of facial muscle movements, we show that posed and spontaneous facial expressions of anger and disgust were more distinct when produced by Dutch compared to Chinese participants. These findings shed new light on the role of culture in emotional communication by demonstrating, for the first time, effects on the distinctiveness of production of facial expressions.

Since large articulated vehicles have uncertainties in trailer articulation angle as well as dynamic complexity, it is not easy to accurately establish a reliable motion plan. In this paper, two geometric path plans constructed based on the empirical rules of driving experts are presented so that articulated vehicles can automatically perform perpendicular parking on a reverse path. By analyzing the empirical parking methods of professional drivers, these path plans were constructed by appropriately combining several standardized simple basic motions to facilitate implementation in real vehicles. In addition, path plans included appropriate complementary motions to effectively respond to uncertainties arising from articulation angles, etc. The complementary motions developed in this study are based on the results of qualitative analysis on the behavior of articulated vehicles. The usefulness of the proposed articulated vehicle parking method has been proven through hundreds of experimental tests using a 1:10 ratio model automated vehicle.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

A robust guaranteed cost preview repetitive controller is proposed for a class of polytopic uncertain discrete-time systems. In order to improve the tracking performance, the repetitive controller combined with preview compensator is inserted in the forward channel. By using the L-order forward difference operator, an augmented dynamic system is constructed. Then, the guaranteed cost preview repetitive control problem is transformed into the guaranteed cost control problem for the augmented dynamic system. For given performance index, the sufficient condition of asymptotic stability for the closed-loop system is derived by combining parameter-dependent Lyapunov function method with linear matrix inequality (LMI) techniques. By incorporating the controller obtained into the original system, the guaranteed-cost preview repetitive controller is derived. A numerical example is also included to show the effectiveness of the proposed method.

In this letter we investigate if SARS-CoV-2 RNA is involved in the increased ageing of alveolar cells. Our in silico study is explorative. With the results we are able to outline experiments with AEC2 repair of bleomycin damaged alveolar cells. If AEC2 repair capability is diminished by spike RNA then perhaps this result provides a first step on a route to treat immortal lung cancer cells.

Lectins, characterized by their carbohydrate-binding ability, have an extensive practical application. However, their industrial use is limited by low yields, and few active recombinant lectins have been reported. In this study, the algal lectin BPL-3 (Bryopsis plumosa lectin 3) was successfully produced using a bacterial expression system, BL21(DE3), with an artificial repeated structure (dimeric construct). Recombinant dimeric BPL3 (rD2BPL3) was confirmed by LC-MS/MS spectrometry. Expression efficiency was greater for the construct with the repeat structure (rD2BPL3) than the monomeric form (rD1BPL3). Optimal conditions for expression were 1 mM IPTG at 20 °C. Recombinant lectin was purified under denaturing conditions and refolded by the flash dilution method. Recombinant BPL3 was solubilized in 1× PBS containing 2 M urea. rD2BPL3 showed strong hemagglutination activity using human erythrocytes, similar to that of native BPL3. rD2BPL3 had a similar sugar specificity to that of the native protein, i.e., to N-acetyl-glucosamine (GlcNAc) and N-acetyl-galactosamine (GalNAc). Glycan array results showed that recombinant BPL3 and native BPL3 exhibited different binding properties. Both showed weak binding activity to α-Man-Sp. Native BPL3 showed strong binding specificity to the alpha conformation of amino sugars, and rD2BPL3 had binding activity to the beta conformation. The process developed in this study was suitable for the quality-controlled production of high amounts of soluble recombinant lectins.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

Next-generation sequencing (NGS) has actualized human papillomavirus (HPV) virome profiling for in-depth investigation of viral evolution and pathogenesis. However, viral computational analysis remains a bottleneck due to semantic discrepancies between computational tools and curated reference genomes. To address this, we developed and tested automated workflows for HPV taxonomic profiling and visualization using a customized Papillomavirus database in CLC Microbial Genomics Module. HPV genomes from Papilloma Virus Episteme were customized and incorporated into CLC “ready-to-use” workflows for stepwise data processing to include: 1) Taxonomic Analysis, 2) Estimate Alpha/Beta Diversities, and 3) Map Reads to Reference. Low-grade (n = 95) and high-grade (n = 60) Pap smears were tested with ensuing collective runtimes: Taxonomic Analysis (36 min); Alpha/Beta Diversities (5 sec); Map Reads (45 min). Tabular output conversion to visualizations entailed 1-2 keystrokes. Biodiversity analysis between low- (LSIL) and high-grade squamous intraepithelial lesions (HSIL) revealed loss of species richness and gain of dominance by HPV-16 in HSIL. Integrating clinically relevant, taxonomized HPV reference genomes within automated workflows proved to be an ultra-fast method of virome profiling. The entire process named “HPV DeepSeq” provides a simple, accurate and practical means of NGS data analysis for a broad range of applications in viral research.

Frequently Asked Questions (FAQs) systems rely on semantic symmetry similarity measuring between two sentences. To address the challenges of insufficient training data and limited domain-specific understanding in low-resource FAQs, this paper proposes a general framework, PDAMF-FAQ, to solve these issues. Firstly, we propose a paraphrasing-based data augmentation model that integrates syntactic information and edit vectors. Using a rule-based approach, it retrieves template sentences from a corpus and masks relevant words with special characters. Edit vectors between the original and paraphrase sentences are added to a pre-trained model's encoding layer to enhance the model's ability to learn the differences between the original and reference paraphrase sentences. Additionally, this paper presents a mixed-feature semantic matching model based on SimBERT. The model extracts keyword features from the text, replacing these keywords with special characters to construct intent features. These intent features, along with the user question and keyword features, are then concatenated to form the model's input. Experiments were conducted respectively on the paraphrasing-based data augmentation model, mixed-feature semantic matching model and their comprehensive application in a low-resource domain-specific FAQ. The experimental results show that the proposed framework effectively improve the performance of domain-specific FAQ system.

Background: Colorectal cancer (CRC) patients experienced multiple chemotoxicity affecting treatment compliance, survival, and quality of life (QOL). Prior research shows clinician-reported chemotoxicity (i.e., grading scales or diagnostic codes) predicts rehospitalization and cancer survival. However, a comprehensive synthesis of clinician-reported chemotoxicity is still lacking. Objectives: We conducted a systematic review and meta-analysis to determine the chemotoxicity's prevalence and risk factors in CRC. Methods: A systematic search from 2009 to 2024 yielded 30 studies for review, with 25 included in the meta-analysis. Results: Pooled prevalences of overall, non-hematological, and hematological moderate-to-severe toxicities were 45.7%, 39.2%, and 25.3%, respectively. The most common clinician-reported chemotoxicities were gastrointestinal (GI) toxicity (22.9%) and neuropathy or neutropenia (17.9%). Significant risk factors at baseline were malnutritional status, frailty, impaired immune or hepato-renal functions, short telomere lengths, low gut lactobacillus levels, age, female sex, aggressive chemotherapy, and low QOL. Age was associated with neutropenia (β: -1.44) and GI toxicity (β:1.85) (Ps 65 y.o.) had higher prevalences of overall (OR: 1.14) and GI (OR: 1.65) toxicities, but a lower prevalence of neutropenia (OR: 0.65) than younger adults (Ps

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Previous studies had shown that mRNA, miRNA and lncRNA were associated with cardiovascular diseases. The study was aimed to explore the differential expressions of mRNA, lncRNA and miRNA between coronary artery disease (CAD) and healthy control, and their interaction in CAD. We investigated the differential expression of ceRNA between CAD and healthy control through data collected from Gene Expression Omnibus (GEO) microarrays. Furthermore, we investigated the biological function of these differential expressions of ceRNAs by Gene Ontology (GO), Kyoto Encyclopedia of Genes and Genomes (KEGG) analyses. Protein-protein interaction (PPI) network was created to identify the hub genes. Biosystems and literature search were performed for signaling pathways and their function of the included differential expression ceRNAs. A total of 456 miRNA expression profiles, 16,325 mRNA expression profiles, and 2,869 lncRNA expression profiles were obtained. Eleven Go and KEGG pathways (count ≥9), top 15 of PPI network node connectivity rank, and top 15 of ceRNA network node degree centrality rank were achieved at the statistical significance level (P<0.05). We further identified that several differential expressions of ceRNAs and their signaling pathways were associated with CAD through biosystems and literature search. Based on eleven Go and KEGG pathways, top 15 of PPI network node connectivity rank, and top 15 of ceRNA network node degree centrality rank in CAD population, our findings would contribute to further exploration for the molecular mechanism of CAD.

The study’s objective is to analyse the mechanical properties of steel pipe piles as a part of a trestle bridge subjected to five years of natural marine corrosion degradation. Sixteen tensile specimens were extracted from the steel pipe piles in the splash, tidal, and immersion zones. The experimental tensile test results are used to establish regression equations defining elastic modulus, yield strength, strain hardening index, and strength coefficient for the true stress-strain curves of the three regions. A non-linear time-dependent mathematical model is exploited to identify the corrosion degradation using the data from one single corrosion degradation measurement campaign. The analysis indicated that the splash zone experiences the most severe corrosion degradation, and there are progressive losses in the mechanical properties of each zone as the corrosion degradation progresses. The established relationships of the mechanical properties, as a function of the ratio of corroded plate thickness to the as-built one, can be used as a fast-engineering approach to identify the mechanical properties of severely corroded piles. The corrosion degradation allowance is also defined using the First Order Reliability Method, accounting for existing uncertainties covered by the partial safety factors. By examining the impact of marine corrosion on the mechanical properties of marine structures and developing predictive models to assess the corrosion’s effect on material strength and corrosion allowance, the study aims to improve offshore structures’ safety, design, and maintenance.

Soil temperature reflects the impact of local factors，such as vegetation，soil and the atmosphere of a region. Therefore, it is important to understand the regional variation of soil temperature. However, lack of observations with adequate spatial and/or temporal coverage, it would be difficult to use the observation data to study the regional variation. Based on the observation data from Nanchang and Ganzhou stations and ERA-Interim/Land reanalysis data, this study analyzed the temporal-spatial distribution characteristics of soil temperature over Poyang Lake Basin. The results showed close correlations between observation data and reanalysis data at different depths. Reanalysis data could mainly reproduce the temporal-spatial distributions of soil temperature over the Poyang Lake Basin, but generally underestimate their magnitudes. Temporally, there is an obvious warming trend in the basin. Seasonally, the temperature raised fastest in spring and slowest in summer, except for the ST4, which rising fastest in spring and slowest in winter. In terms of depths, the temperature of ST1 rises fastest. For the other layers, the warming trend is almost similar. An abrupt change of annual soil temperature at all depths occurred in 1997, and annual soil temperatures at all depths were abnormally low in 1984. Spatially, annual soil temperature decreased with latitude, except for the summer ST1. Because of the high temperature and precipitation in summer, the ST1 are higher around the lake and the river. The climatic trend of soil temperature presents the general increase trend from south to north, opposite to the distribution of soil temperature. The findings provide a basis for understanding and assessing the variation of the soil temperature over the Poyang Lake Basin.

Colleges and universities play a crucial role in fostering innovation, making it essential to explore effective strategies for promoting innovation at the institutional policy level. This paper focuses on the establishment of intellectual property (IP) model cities as a starting point and conducts an empirical analysis using innovation data from 234 cities and 942 colleges and universities between 2007 and 2017. By constructing a multi-temporal double-difference model, this study reveals that the establishment of IP model cities effectively fosters innovation in colleges and universities. Further analysis demonstrates that this promotion effect is particularly significant in the western region, key cities, key colleges and universities, as well as in the fields of invention and utility model patents. These conclusions withstand a series of robustness tests, confirming their validity. In terms of the underlying mechanisms, it is found that the national IP pilot city policy has a substantial impact on university innovation by promoting research and development (R&D) investment and strengthening innovation cooperation. The insights provided by this study offer valuable policy recommendations for leveraging the innovation potential of the IP model city policy, thereby driving economic transformation, upgrading, and fostering innovation development in China.

We describe a novel system for online prediction of lead seizures from long-term intracranial electroencephalogram (iEEG) recordings for canines with naturally occurring epilepsy. This study adopts new specification of lead seizures, reflecting strong clustering of seizures in observed data. This clustering results in fewer lead seizures (~7 lead seizures per dog), and hence new challenges for online seizure prediction, that are addressed in the proposed system. In particular, machine learning part of the system is implemented using the Group Learning method suitable for modeling sparse and noisy seizure data. In addition, several modifications for the proposed system are introduced to cope with non-stationarity of noisy iEEG signal. They include: (1) periodic re-training of SVM classifier using most recent training data; (2) removing samples with noisy labels from training data; (3) introducing new adaptive post-processing technique for combining many predictions made for 20-second windows into a single prediction for 4 hr segment. Application of the proposed system requires only 2 lead seizures for training the initial model, and results in high prediction performance for all four dogs (with mean 0.84 sensitivity, 0.27 time-in-warning, and 0.78 false-positive rate per day). Proposed system achieves accurate prediction of lead seizures during long-term test periods, 3–16 lead seizures during 169–364 days test period, whereas earlier studies did not differentiate between lead vs. non-lead seizures and used much shorter test periods (~few days long).

Background: After allogeneic hematopoietic stem cell transplantation (allo-HSCT), acute leukemia relapse is common, and asymmetric bone marrow recurrence hasn’t been reported. Because the anatomical distribution of acute leukemia clones in the bone marrow after allo-HSCT is presumed to be diffuse, bone marrow aspirations are performed in single site. Case presentation: We identified two acute leukemia patients, whose leukemic burden in bilateral bone marrow specimens differed significantly. The first case was a 20-year-old man who was diagnosed with acute myelomonocytic leukemia and received haploidentical allo-HSCT. He had been in complete remission for two years and off immunosuppressive medications for a year, with normal peripheral blood count. Routine bone marrow biopsy of his left posterior iliac bone marrow showed 52% leukemia blasts, while the right side had 0% blasts ten days later. Due to the discordant results, the patient refused further intervention and died of high leukocyte syndrome four months later. The second case was a 23-year-old woman who was diagnosed with acute B lymphoblastic leukemia and received HLA-identical sibling allo-HSCT. Although 62% of blasts were found in her left iliac marrow on day +122, 0 % of blasts were found on a sample obtained from the right iliac crest on day +128. Whole-body 18F-FDG PET/CT scans confirmed that the leukemic infiltration in her bone marrow was asymmetric. Considering the higher leukemic burden on the left, we chose the left posterior iliac crest aspiration for further response evaluation. After chemotherapy combined with donor lymphocyte infusion, she achieved transient hematologic complete remission. She died of septic shock with heart failure at +258 days after allo-HSCT before infusion of anti-CD19 donor chimeric antigen receptor T cells. Conclusions: To our knowledge, these are the first case reports of asymmetric bone marrow infiltration of blasts in acute leukemia patients after allo-HSCT. Bilateral posterior iliac crest aspirations or 18F-FDG-PET/CT scans may help distinguish such distribution. If discordant bone marrow specimens are observed, physicians should restrict future bone marrow studies to the more involved side.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

In recent years, there has been a notable rise in the incidence of breast cancer among young patients, who exhibit worse survival outcomes and distinct characteristics compared to the intermediate and elder patients. Therefore, it’s imperative to identify identify the specific features unique to young patients, which could offer insights into potential therapeutic strategies and improving survival outcomes. In our study, we performed an integrative analysis of bulk transcriptional and genomic data from extensive clinical cohorts to identify prognostic factors. Additionally, we analyzed the single-cell transcriptional data and conducted in vitro experiments. Our work confirmed that young patients exhibited higher grading, worse disease-free survival (DFS), a higher frequency of mutations in TP53 and BRCA1, a lower frequency of mutations in PIK3CA, and upregulation of eight metabolic pathways. Notably, galactose metabolism pathway showed upregulation in young patients and was associated with worse DFS. Further analysis and experiments indicated that galactose metabolism pathway may regulate the stemness of cancer cells and ultimately contribute to worse survival outcomes. In summary, our finding identified distinct clinicopathological, transcriptional, and genomics features and revealed a correlation between galactose metabolism pathway, stemness, and poor disease-free survival of breast cancer in young patients.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

A number of epidemiological studies have implicated elevated iron levels with higher risks of cardiometabolic diseases, including the metabolic syndrome (MetS). MetS is a pathologic clustering of metabolic derangements characterized by central obesity, insulin resistance, hypertension, and dyslipidemia, which can all lead to increased cardiovascular disease morbidity and mortality. However, it remains unclear whether a causal association exists between higher iron status and MetS and its associated risk components. Using the data from the Taiwan Biobank (TWB) (19,012 males; 42,340 females) and of the European Whites from the UK Biobank (UKB) (128,549 males; 142,817 females), we first constructed ethnic- and sex-specific hemoglobin-polygenic risk scores (Hb-PRS) as instrumental variable (IV) for iron status with the Hb-associated SNPs we previously identified from genome-wide association studies (GWAS). We then conducted Mendelian randomization (MR) analyses to elucidate the causal role of elevated iron (either Hb-PRS quintiles or continuous Hb-PRS) on various metabolic components. MR-Egger regressions determined the potential pleiotropic effects of the constructed Hb-PRSs, while the causal relationship of Hb-PRS with anemia served as a control in the analyses. The mean Hb concentration range corresponding to the Hb-PRS quintiles is relatively narrow in both UKB (14.91-15.21 g/dL for males and 13.39-13.71 g/dL for females) and TWB (14.79-15.28 g/dL for males and 12.78-13.21 g/dL for females). In these windows of Hb-PRSs, we found differential associations of Hb-PRS with diabetes (T2D) or hyperglycemia (HGY) as compared to other MetS components. The highest quintiles of Hb-PRSs were causally associated with greater risks of hypertension (HTN) and hypertriglyceridemia (DLP) (i.e., [Taiwanese HC males: Q5 vs. Q1 ORHTN = 1.10 (1.00–1.21), p = 0.0473, Q4 vs. Q1 ORDLP = 1.10 (1.00–1.22), p = 0.0485; European White males: ORHTN = 1.05 (1.01–1.09), p = 0.0194, ORDLP = 1.04 (1.00–1.08), p = 0.0468]). Interestingly, we obtained a consistent negative causal association between increasing Hb-PRS quintiles and T2D or HGY risk across all sex subgroups (i.e., [Taiwanese HC females: ORHGY = 0.89 (0.84–0.95), 0.88 (0.83–0.94), 0.87 (0.82–0.93), 0.86 (0.81–0.92) from Q2 to Q5; European White females: ORHGY = 0.92 (0.87–0.98), 0.91 (0.86–0.97), 0.93 (0.87–0.98), 0.87 (0.82–0.93) from Q2 to Q5; all p &lt; 0.05]. The positive causal relationships between Hb-PRSs and diastolic blood pressure (DBP) and triglycerides (TG) but inverse causal association with glucose (GLU) and glycated hemoglobin (HbA1c) further corroborated such findings. There is, however, a lack of causal association with central obesity (CO), while a U-shaped type of causality was observed for gout (GT) or hyperuricemia (HUA). Sensitivity analyses, which excluded subjects based on self-reports of health conditions or medications and hospital episode statistics data, revealed similar results. Our MR studies confirm a modest causal relationship between propensity of elevated iron status and increased risk of HTN and DLP. We have further observed that modestly lower iron levels causally contribute to the development of T2D. Further validation and elucidation of the underlying biological mechanisms are highly warranted.

Aromatic azo compounds have -N=N- double bonds as well as larger π electron conjugation system, which endows aromatic azo compounds with wide applications in the fields of functional materials. The properties of aromatic azo compounds are closely related to the substituents on their aromatic rings. However, traditional synthesis methods, such as the coupling of diazo salts, have a great limitation on the structural design of aromatic azo compounds. Therefore, many scientists have devoted their efforts to developing new synthetic methods. Moreover, recent advances in the synthesis of aromatic azo compounds led to the improvement of design and preparation of light-response materials at molecular level. This review summarizes the important synthetic progress of aromatic azo compounds in recent years, with an emphasis on the pioneering contribution of functional nanomaterials in the field.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Prunus tenella is a rare and precious relict plant in China. It is an important genetic resource for almond improvement and an indispensable material in ecological protection and landscaping. However, the research of molecular breeding and genetic evolution has been severely restricted, due to the lack of genome information. In this investigation, we created a chromosome-level genomic pattern of P. tenella, 231Mb in length with a contig N50 of 18.1 Mb by Hi-C techniques and high-accuracy PacBio HiFi sequencing. The present assembly predicted 32088 protein-coding genes, and an examination of the genome assembly indicated that 94.7% among all assembled transcripts were alignable to the genome assembly; most (97.24%) were functionally annotated. By phylogenomic genome comparison, we found that P. tenella is an ancient group that diverged approximately 13.4 million years ago (Mya) from 13 additional closely related species and about 6.5 Mya from the cultivated almond. Collinearity analysis revealed that P. tenella is highly syntenic and has high sequence conservation with almond and peach. However, this species also exhibit many presence/absence variants. Moreover, a large inversion at the 7,588 kb position of chromosome 5 was observed, which may have a significant association with phenotypic traits. Lastly, population genetic structure analysis in eight different populations indicated a high genetic differentiation among the natural distribution of P. tenella. This high-quality genome assembly provides critical clues and comprehensive information for the systematic evolution, genetic characteristics, and functional gene research of P. tenella. Moreover, it provides a valuable genomic resource for in-depth study in protecting, developing, and utilizing P. tenella germplasm resources.

Compressed Sensing (CS) MRI has shown great potential in enhancing time efficiency. Deep learning techniques, specifically Generative Adversarial Networks (GANs), have emerged as potent tools for speedy CS-MRI reconstruction. Yet, as the complexity of deep learning recon-struction models increases, this can lead to prolonged reconstruction time and challenges in achieving convergence. In this study we present a novel GAN-based model that delivers superior performance without escalating model complexity. Our generator module, built on the U-net architecture, incorporates dilated residual (DR) networks, thus expanding the network's receptive field without increasing parameters or computational load. At every step of the downsampling path, this revamped generator module includes a DR network, with the dilation rates adjusted according to the depth of the network layer. Moreover, we have introduced a channel attention mechanism (CAM) to distinguish between channels and reduce background noise, thereby fo-cusing on key information. This mechanism adeptly combines global maximum and average pooling approaches to refine channel attention. We conducted comprehensive experiments with the designed model using public domain MRI datasets of the human brain. Ablation studies af-firmed the efficacy of the modified modules within the network. Compared to other relevant models, our proposed model exhibits exceptional performance, achieving not only excellent sta-bility but also outperforming other networks in terms of Peak Signal-to-Noise Ratio (PSNR) and Structural Similarity Index (SSIM). The model presents a promising pathway for enhancing the efficiency and quality of CS-MRI reconstruction.

In this study, 3-trimethoxy-silylpropane-1-thiol (MPTMS) was used as a surface modifier for Al2O3 powder to systematically analyze the effects of MPTMS concentration on the rheological properties, photocuring characteristics, and 3D printing performance of photocurable composite slurries. MPTMS concentration significantly influenced the rheological behavior of the slurry. Slurries containing 2 wt.% and 5 wt.% MPTMS exhibited a wide linear viscoelastic range (LVR). However, at concentrations of 10 wt.% and 20 wt.%, the LVR range narrowed, which led to reduced dispersion stability. In dispersion stability tests, the slurry with 2 wt.% MPTMS showed the most stable dispersion, while the 5 wt.% MPTMS concentration exhibited the highest photocuring rate. In 3D printing experiments, the 5 wt.% MPTMS concentration resulted in the most stable printed structures, whereas printing failures occurred with the 2 wt.% concentration. At 10 wt.% and 20 wt.%, internal cracking was observed, leading to structural defects. In conclusion, MPTMS forms silane bonds on the Al2O3 surface, significantly impacting the stability, rheological properties, and printing quality of Al2O3-acrylate composite slurries. An MPTMS concentration of 5 wt.% was found to be optimal, contributing to the formation of stable and robust structures.

In this paper, we present a full coverage path planning (CPP) algorithm for the marine surveys conducted in the convex polygon shaped search area. The survey is supposed to carry out by torpedo-type AUVs (autonomous underwater vehicles). Due to their nonholonomic mechanical characteristics, these vehicles have nonzero minimum turning radius. For any given polygon shaped search area, it can always be partitioned into one or more convex polygons. With this in mind, this paper proposes a novel search algorithm called CbSPSA (Calculation based Shortest Path Search Algorithm) for full coverage of any given convex polygon shaped search area. By aligning the search inter-tracks alongside the edge with the minimum height, we can guarantee the minimum number of the vehicle’s turns. In addition, the proposed method can guarantee the planned path is strictly located inside the polygon area without overlapped or crossed path lines, and also has the total path length as short as possible. Considering the vehicle’s nonzero minimum turning radius, we also propose a sort of smoothing algorithm to smooth the waypoint path searched by CbSPSA so as for the vehicle to exactly follow it. The smoothed path is also guaranteed to be strictly located inside the polygon. Numerical simulation analyses are also carried out to verify the effectiveness of the proposed schemes.

Surface defect detection is a crucial step in the process of automotive wheel production. However, the task possesses challenges due to complex background and a wide range of defect types. In order to detect the defects on the wheel surface accurately and quickly, this paper proposes a YOLOv5-based algorithm for automotive wheel surface defect detection. The algorithm trains and tests the YOLOv5s model using the self-created automotive wheel surface defect dataset, which contains four kinds of defects: linear, dotted, sludge, pinhole. The extensive experimental results demonstrate that the deep learning network trained by our method can achieve an average accuracy of 71.7% and 57.14 FPS. Our findings prove that this detection algorithm performs better than other common target detection algorithms and meets the real-time requirements of industrial applications.

This paper investigates the leader–follower formation tracking control of underactuated surface vessels (USVs) with input saturation. Each vessel is subject to the uncertainties induced by model uncertainties and environmental disturbances. At first, an event-trigged extended state observer (ETESO) is used to recover the velocity, yaw rate and the uncertainties. Then, an estimator is used to estimate velocity of the leader. An event-trigged controller (ETC) is constructed based on the estimator, the observer and extra variables. Specifically, extra variables are used to solve the underactuated problem and input saturation. Stability analysis of control system is given to prove all signals are bounded. Simulations demonstrate that the ETESO can estimate accurately the uncertainties, the velocity and yaw rate; the ETC can largely reduce the action times of actuator.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

The assessment of water quality consists of counting bacteria indicating fecal contamination or detecting the presence of pathogenic bacteria using standardized or validated methods of classical microbiology. Our present study aims to determine the bacteriological quality of drilling water in the Tandjilé region of Chad. Our method used was based on qualitative and quantitative research on suspected total coliforms, Echerichia Coli and fecal enterococci were analyzed according to the standard routine methods of the French Association for Normalization (AFNOR). Microbiological analysis shows the presence of indicators of fecal contamination such as total coliforms, Escherichia coli and fecal enterococci. The number of strains detected in 100 ml were E. coli (7 /29 samples), fecal Streptococcus (6 /29 samples) and total coliforms (29/29 samples), respectively from borehole water. The contamination rate of E. coli is 24.13%, total coliforms 100% and 20.68% of fecal enterococci in boreholes. The high number of these microorganisms is more than the values recommended by the WHO for the quality of drinking water. Corrective and urgent measures are needed to improve the quality of these water resources, rich in pathogens, which are health risks, and the causes of infectious diseases such as gastroenteritis, diarrhea, typhoid and skin diseases.

Music therapy has served as complementary and alternative medicine for various neurological disorders. Five Phases Music Therapy (FPMT) employs the theory of five phases and five music scales or tones (宫Gong (do), 商Shang (ri), 角Jue (mi), 徵Zhi (so) and 羽Yu (la)) to analyze and treat mind-body illness. In Chinese Medicine (CM), the five music scales are used to connect the human body and the universe, interpret personalities and constitution and analyze the influences of climatic changes on health. FPMT has a self-contained theory and routine of practice application. Large amounts of clinical and fundamental reports have been available and clinical benefits have been obtained. However more systemic clinic research esp. evidence-based and random controlled trials must be performed to validate and optimize its routines and biological and neurological mechanism must be further explored. It’s reasonable to believe that the effective music therapy will attract more attention from the world outside China with the introduction of FPMT.

This study examines Tim Rowett's YouTube channel, "Grand Illusions," which captures and maintains positive viewer engagement in the digital domain. Through a comprehensive YouTube channel analysis, this paper identifies key factors contributing to its success, including collaboration and influence, educational impact, legacy and continuity, personal style, and community engagement. Rowett, known for his extensive toy collection and in-depth knowledge of their mechanics and history, employs an educational and engaging presentation style that fosters a positive and inclusive online community. His approach entertains and educates, making him a valuable digital resource that inspires viewers of all ages. This research proposes the CECCE (Collaboration, Education, Continuity, Community Engagement) model as a framework for content creators seeking to replicate the success of "Grand Illusions." The study emphasizes the potential of tailored, passionate content to cultivate healthy digital communities and underscores the significant role of digital content creators in shaping online culture. The proposed framework will guide creators to achieve similar success.

This research presents the Cross-Cultural Intelligent Language Learning System (CILS), a novel approach integrating Artificial Intelligence (AI) into language education to enhance cross-cultural communication. CILS utilizes advanced AI technologies to provide adaptive, personalized learning experiences that cater to the unique linguistic and cultural backgrounds of each learner. By dynamically adjusting content and methodology, CILS significantly improves linguistic proficiency and cultural understanding, essential for effective global interactions. The implementation of CILS in platforms such as Busuu and HelloTalk has demonstrated marked improvements in engagement and communication skills among learners. Empirical studies validate the system's effectiveness in real-world settings, showing enhanced learner performance and increased intercultural competence. Additionally, the Technology Acceptance Model (TAM) applied confirms that the usability and perceived usefulness of AI-driven systems strongly influence learner acceptance and sustained use. This study not only underscores the potential of AI in transforming language education but also highlights the critical role of cultural sensitivity in designing educational technologies.

Well-annotated gene and genomic sequences serve as a foundation for making inferences in molecular biology and evolution, and can directly impact public health. The first SARS-CoV-2 genome was submitted to GenBank and used to develop the two successful vaccines. Conserved protein domains are often chosen as targets for developing antiviral medicines or vaccines. Mutation and substitution patterns provide crucial information not only on functional motifs and genome/protein interactions but also for characterizing phylogenetic relationships among viral strains. These patterns, together with the collection time of viral samples, serve as the basis for addressing the question of when and where the host-switching event occurred. Unfortunately, viral genomic sequences submitted to GenBank undergo little quality control, and critical information in the annotation is frequently changed without being recorded. Researchers often have no choice but to hold blind faith in the accuracy of the sequences. There have been reports of incorrect genome annotation but no report that casts doubt on the genomic sequences themselves because it seems theoretically impossible to identify genomic sequences that may not be authentic. This paper takes an innovative approach to show that some SARS-CoV-2 genomes submitted to GenBank cannot be possibly authentic. Specifically, some SARS-CoV-2 genomic sequences deposited in GenBank with collection time in 2023 and 2024, isolated from saliva, nasopharyngeal, sewage, and stool are identical to the reference genome of SARS-CoV-2 (NC_045512). The probability for such occurrence is effectively 0. I also compile SARS-CoV-2 genomes with changed sample collection time. One may led astray in bioinformatic analysis without being aware of errors in sequences and sequence annotation.

Increasing efforts have been devoted to promoting sustainable demolition waste management (DWM) from a life cycle-thinking perspective. To this end, facilitating sustainability-oriented de-cision-making for DWM planning requires a sustainability assessment framework for assessing multifaceted criteria. This study develops a BIM-based DWM sustainability assessment ap-proach to facilitate the life cycle assessment (LCA) and decision-making by coupling the enriched IFC model with hybrid Multi-Criteria Decision-Aiding (MCDA) methods using Dynamo visual scripting. To streamline the data-intensive LCA process, this study enriched the BIM properties and accommodated them into the LCA data template to enhance data interoperability, thus achieving seamless data transfer. Moreover, hybrid MCDA methods are integrated into the deci-sion-making workflow for DWM scenario ranking. A pilot study is employed to verify the ap-plicability of the decision-aiding framework. The results unveil that the sustainability score ascended with the recycling rate. The optimal DWM alternative with the highest recycling rate yields the highest sustainability score at 91.63. Conversely, a DWM alternative reflecting the ‘status quo’ in China’s recycling industry has the lowest score at 8.37, significantly lower than the baseline scenario with a 50% recycling rate. It is worth noting that the ‘growth curve’ of the sustainability score continuously flattens as the target recycling rate escalates. The increment in recycling rate from the “Australian standard” scenario to the optimal scenario is 18.4%, while the sustainability score merely increases by 2.3%, signal-ling that the former scenario arrived at an optimum point for maximising the cost-efficiency of DWM under the predefined framework and contexts.

In this paper, the preparation methods of porous silicon nitride materials with controllable dielectric constant and pore structure were systematically studied. By using microwave sintering technology, porous silicon nitride materials with high closed pore ratio were prepared by adjusting the content of sintering additives and sintering process parameters, and controlling the grain boundary phase and pore structure and size. The effects of sintering conditions on the total porosity, closed porosity, pore structure and dielectric properties of materials were systematically studied.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

Based on panel data of 31 provincial-level administrative units (excluding Hong Kong, Macao and Taiwan) in China from 2015 to 2019, using fixed effect model and mediation effect model, this paper makes an empirical analysis on the interaction among digital economy, industrial structure upgrade and high-quality economic development. The results show that, from the overall effect, the digital economy can significantly promote the high-quality development of the economy, and there are regular regional differences, and the relationship between the promotion intensity and the development level of the digital economy is proportional. From the mediation effect, in the relationship between digital economy and high-quality economic development, the upgrade of industrial structure has played a significant part of the mediation effect, the proportion of mediation effect is 25.17% . In addition, the mediation effect of industrial structure upgrade has obvious regional difference, the western area is the strongest, the eastern area is the second, the central area is the weakest. Based on the above research,the concrete policy suggestions are given to promote the development of digital economy and upgrade the level of industrial structure to promote the high-quality development of economy.

The present study provides molecular insight into the mechanisms underlying energy dissipation and lubrication of a smooth contact lubricated by an ionic liquid. We have performed normal and lateral force measurements with a surface forces apparatus and by colloidal probe atomic force microscopy on following model systems: 1-ethyl-3-methyl imidazolium bis-(trifluoro-methylsulfonyl)imide, in dry state and in equilibrium with ambient (humid) air; the surface was either bare mica or functionalized with a polymer brush. The velocity-dependence of the friction force reveals two different regimes of lubrication, boundary-film lubrication, with distinct characteristics for each model system, and fluid-film lubrication above a transition velocity V*. The underlying mechanisms of energy dissipation are evaluated with molecular models for stress-activated slip and flow, respectively. The stress-activated slip assumes that two boundary layers (composed of ions/water strongly adsorbed to the surface) slide pass each; the bond dynamics and the strength of the interaction at the slip plane dictate the change in friction -decreasing, increasing or remaining constant- with velocity in the boundary-film lubrication regime. Above a transition velocity V*, friction monotonically increases with velocity in the three model systems. Here, layers of ions slide past each (“flow”) under a shear stress and friction depends on a shear-activation volume that is significantly affected by confinement. The proposed friction model provides a molecular perspective of the lubrication of smooth contacts by ionic liquids and allows identifying the physical parameters that control friction.

This study measures the noise levels in a baseball stadium and analyzes baseball fans’ attitude of effect of recreational noise exposure on their hearing. In the baseball stadium, noise levels were measured in four seating sections using a sound level meter during the games. The LAeq average of the 16 measures produced 91.7 dBA, showing a significantly high noise level in the red and navy sections. As a function of frequency by LZeq analysis, the noise levels were significantly higher in low frequencies than other frequencies. For the survey sample, 688 randomly selected participants completed a 16-question survey on their noise exposure during the game and on the potential risk of hearing loss. Despite the very high noise levels, 70% of the respondents preferred sitting in either the red or the navy section to be closer to the cheerleaders and to obtain a good view. Most respondents reported that they did not consider wearing earplugs, and one-third experienced hearing muffled speech after the game. We conclude that the noise levels in baseball stadiums are high enough to cause hearing damage and/or tinnitus later, but expect these results to improve public education regarding safe noise exposure during popular sports activities.

The power system vulnerability leads to faults and the severity of the fault may lead to prolonged load-shedding. The power system needs to be configured in extreme failure scenarios for protecting the network from further contingencies and prolonged load-shedding. Distributed generation resources (DGs) can be useful to form intentional islands after faults to maintain the continuity of power supply to loads based on their weightage during faulty periods and to reduce overall load shedding duration. Power system is bound to collapses and secondary collapse in the formed island is possible. This research represents a novel method of impedance based path finding for intentional islanding, which adapts itself with the changes in the demands, DGs outputs or further severities during restoration period. In this adaptive islanding approach, network adjusts itself with the changes in either the load demands or renewable DGs outputs and rearranges the restoration plan by curtailing or adding some of the loads through controllable switches. Further a secondary collapse in the existing island is studied by injecting multiple faults at various positions of the network to validate the system resilience to cope with severities. A short-term load forecasting approach is used to predict changes in load demands and variations in DG outputs during the islanding scheme. During the restoration period, these variations are tracked and the islands are modified accordingly. In order to minimize the overall generation cost by using less fuel, an economical approach is used in the selection of controllable DGs. The proposed approach is formulated as a multi-objective, that incorporates several operational constraints and simulation is carried out using the modified IEEE 69-bus distribution system to assess the efficacy of the proposed model.

The chitin synthase B gene is a key enzyme in the chitin synthesis of insect peritrophic matrix (PM), affecting insects' feeding behavior. The chitin synthase B gene has been cloned from the transcription library of Heortia vitessoides Moore. RT-qPCR showed that HvChsb was highly expressed in the larval stage of H. vitessoides, especially on the first day of the prepupal stage, and in the midgut of larvae and the abdomen of adults. After starvation treatment, HvChsb was found to be significantly inhibited with time. After 48 h of starvation, the feeding experiment showed that HvChsb increased with the prolongation of the refeeding time. The experimental data showed that feeding affected the expression of HvChsb. HvChsb was effectively silenced by RNA interference, so its function was lost, significantly decreasing the survival rate of H. vitessoides. The survival rate from larval-to-pupal stages was only 43.33%, accompanied by abnormal phenotypes. It can be seen that HvChsb plays a key role in the average growth and development of H. vitessoides.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

The primary aim of this study was to investigate the variations in cognitive load as self-efficacy gradually increases and examine the potential within-mediating effect of state anxiety between self-efficacy and cognitive load. The experiment manipulated the self-efficacy of 49 adult participants through the false feedback paradigm, employing a within-subject experimental design and using facial expression recognition as the experimental task. The data were analyzed using Hierarchical Linear Modeling. The results revealed that self-efficacy negatively predicted state anxiety and cognitive load, while state anxiety positively predicted cognitive load. Moreover, state anxiety played a complete mediating role at multiple levels in this process.

To date, viral RNA detection is almost the only way to confirm SARS-CoV-2infectionin practice.However, variousreasons can cause low sensitivity for RNA detection, and thisposes aserious challenge to disease control. We tested the performance of detecting total antibody(Ab) and IgM levels in serum by the methods of chemiluminescence, enzyme-linked immunosorbent assay (ELISA), and colloidal golddetection. The datashowed that the sensitivity and specificity for detecting total Ab and IgM levels were high by all three methods, and the sensitivity was higher for detecting total Ab than for detecting IgM. Evidence from studieshas shown thatviral RNA testingcombinedwith serological testing could increase the diagnostic sensitivity while maintaining a high specificity. Specific serology testsfor SARS-CoV-2 havegreat value for clinical practice and public health.