Over the last ten years, the integrated pond aquaculture (IPA) has been developing rapidly as a new aquaculture mode, and mechanical power oxygenator is a common oxygenation device in this aquaculture mode. However, with the gradual expansion of the application range of this aquaculture mode, the problems of low efficiency, poor oxygenation uniformity, and low applicability of mechanical power oxygenators, which can produce water reflux and suction pollution accumulation, have gradually emerged. Therefore, we designed a new type of push-water aerator device (NPWAD) applicable to the integrated recirculating water aquaculture mode of ponds. Mainly, the specific parameters of the key components were clarified through the selection calculation and structural design, and the experiments were carried out in the self-constructed pond integrated aquaculture system at the experimental base. The experiments were carried out on the water in the tank for grass carp culture, and the oxygenation and water pushing effects of the type of push-water aerator device under 15 groups of different operating parameters were carried out by using multiple types of high-precision water quality monitoring sensors, with the rotational speed of the device, the operating time (0-30 min) and the height of the water (0.5-1.5 m) as the independent variables, and the oxygenation amount R, the oxygenation power efficiency E_s and the surface layer of the water as the evaluation indexes, average flow velocity V_f were used as its evaluation indexes of oxygenation and water pushing. The results show that the optimal parameters of the NPWAD are impeller water lifting component speed n_1=1000r/min, small-hole aeration component speed n_2=2280r/min. At this time, the average oxygen increase of this device is R=1.96mg/L, the average oxygenation power efficiency is E_s=3.8 kg·(h·kW)-1, the DO uniformity of the water M_1=95.3%, and the average flow velocity V_f=190.8mm/s, which can effectively promote the water directional flow and achieve the water circulation and layer exchange, and it is in line with the preferred swimming speed of grass carp at various growth stages. The new type of push-water aerator device is able to enhance the DO concentration of the water faster, but also to achieve the purpose of promoting the directional flow of the water and renewing the water in the tank, as well as in a short period of time to improve the uniformity of the DO of the water faster, for the improvement of the pond aquaculture production efficiency has practical significance.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Relative to several model bacteria, the ethanologenic bacterium Zymomonas mobilis is shown here to have an elevated resistance to exogenous antimicrobial peptides (AMPs) – both, with regard to peptide bulk concentration in the medium, and the numbers of peptide molecules per cell. By monitoring integration of the AMPs in the bacterial cell membrane and observing the resulting effect on membrane energy-coupling, it is concluded that the membranotropic effects of the tested AMPs in Z. mobilis and in Escherichia coli are comparable. The advantage of Z. mobilis over E. coli apparently results from its uncoupled mode of energy metabolism that, in contrast to E. coli, does not rely on oxidative phosphorylation, and hence, is less vulnerable to disruption of its energy-coupling membrane by AMPs. It is concluded that the high resistance to antimicrobial peptides (AMPs) observed in Z. mobilis not only proves crucial for its survival in its natural environment but also offers a promising platform for AMP production and sheds light on potential strategies for novel resistance development in clinical settings.

Clarifying the response of plant phenology to drought duration is helpful for accurately interpreting and predicting carbon sinks in ecosystems. Based on the response of different phenological periods of the dominant species Stipa krylovii to monthly, seasonal and semiannual time scale drought in the typical steppe of Inner Mongolia from 1983 to 2018, the results revealed that (1) the start of the growing season (SOS) was characterized by an advance-delay-advance pattern, and the heading stage (HOS), flowering stage (FOS) and end of the growing season (EOS) all showed consistent advanced trends, which provided additional insight into the conclusions of previous studies that found the SOS was advanced in arid and semiarid regions. (2) The response mechanism of the SOS to the timing of drought was not consistent. Among the response mechanism, the SOS was delayed because of January-February drought at different time scales, but advanced because of April drought at different time scales. The HOS/FOS was delayed by June-July drought at different time scales, and the EOS was advanced by August-September drought at different time scales. (3) More importantly, the SOS, HOS, FOS and EOS were affected by predrought and its persistence, and the effects were greater the closer to the phenological periods that drought occurred. (4) At the monthly scale, droughts in January, June and August were the critical drought periods affecting the SOS, HOS/FOS and EOS, while seasonal and semiannual scale droughts in February, June-July and September were the critical periods affecting the SOS, HOS/FOS and EOS. The results of this study enrich our understanding of how drought at different time scales affects different phenological periods, providing a basis for improving plant phenological models.

Impressively increasing availability of the mechanical circulatory/cardiac support systems (MCS) worldwide, together with the deepening of the knowledge of critical care medical practitioners, have inevitably led to the discussion about further improvements of intensive care associated to MCS. An appealing topic of the left ventricle (LV) overload related to VA ECMO support endangering myocardial recovery is being widely discussed within the scientific community. Unloading of LV leads to the reduction of LV end-diastolic pressure, reduction of pressure in the left atrium and decrease of the LV thrombus formation risk. Consequently, better conditions for myocardial recovery, with comfortable filling pressures and better oxygen delivery/demand ratio are achieved. The combination of VA ECMO and Impella device, also called ECPELLA seems to be a promising strategy which may bring the improvement of CS mortality rates. The series of presented trials and meta-analyses clearly showed potential benefits of this strategy. However, the ongoing research has brought a series of new questions, as whether Impella itself is the only appropriate unloading modality, or any other approach to unload LV would be beneficial in the same way? Benefits and potential risks of LV unloading and its timing are being discussed in current review.

The insufficient of fish meal has been become a prominent problem with the development of the aquaculture industry. Therefore, it is great significance that replacement fish meal using other protein sources for the sustainable development of aquaculture industry. In this study, fermented cottonseed meal (FCM) and fermented rapeseed meal (FRM) were used to replace fish meal in Chinese mitten crab. The ratio of FCM and FRM were set according to 1:2, 1:1, and 2:1, and were supplemented into 25% fish meal (FM-25) and 15% fish meal (FM-15) diets, respectively, to formulated 6 kinds of experimental diets. The feeding duration was 8 weeks. The results showed that the weight gain (WG) and specific growth rate (SGR) of crabs fed the diets containing 25% fish meal were significantly higher than crabs fed 15% fish meal diets. At 25% fish meal level, the WG and SGR of crabs fed the diet with 1FCM:1FRM were significantly higher than those fed the 1FCM:2FRM and 2FCM:1FRM diets. At 25% fish meal level, the crude lipid (CL) content of crabs fed the diet with 1FCM:2FRM were significantly higher than those fed the 2FCM:1FRM and 1FCM:1FRM. At 25% fish meal level, the activities of glutathione peroxidase (GPX) and peroxidase (POD) of crabs fed the diet with 1FCM:2FRM were significantly higher than those fed the 2FCM:1FRM and 1FCM:1FRM. At 25% fish meal level, the relative expression of peroxiredoxin (PRX) of crabs fed the diet with 1FCM:1FRM were significantly higher than those fed the 2FCM:1FRM and 1FCM:2FRM. In summary, diets supplemented with a mixture of fermented cotton meal and fermented rapeseed meal (1:1) can significantly improve the growth and antioxidant capacity of Chinese mitten crab.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

The main sources of intrinsic noise in excitable cells at the microcircuit and network levels are the stochastic characteristics of ion channel gating and activation of the synaptic conductance. Studies using in vivo, in vitro, and in silico methods to examine the effects of synaptic background activity were not adequately investigated in non-neuronal excitatory cells, where neurotransmitter-based innervation also occurs. We created a mathematical model to replicate the background synaptic noise dynamics in a non-neuronal cell. We utilized the stochastic Ornstein-Uhlenbeck process to represent excitatory synaptic conductance, which was incorporated into a whole-cell model to produce spontaneous and evoked cellular electrical activities. The single-cell model includes many biophysically detailed ion channels represented by a set of ordinary differential equations in Hodgkin-Huxley and Markov formalisms. This paradigm effectively induced irregular spontaneous depolarizations (SDs) and spontaneous action potential (sAP) resembling in vitro-like electrical activity in the cells. The input resistance decreased by multiple factors, and the spontaneous action potential firing rate elevated. The potential to reach the action potential threshold is altered. Background synaptic activity can alter the input/output characteristics of non-neuronal excitatory cells. Suppressing these baseline activities would facilitate the discovery of new pharmaceutical targets for different clinical diseases.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

With the rapid evolution of SARS-CoV-2, the emergence of new strains is an intriguing question. This paper presents an evolutionary theory to analyze the mutations of the virus and identify the conditions that lead to the generation of new strains. We represent the virus variants using a 4-letter sequence based on amino acid mutations on the spike protein and employ an n-distance algorithm to derive a variant phylogenetic tree. We show that the theoretically-derived tree aligns with experimental data on virus evolution. Additionally, we propose an A-X model, utilizing the set of existing mutation sites (A) and a set of randomly generated sites (X), to calculate the emergence of new strains. Our findings demonstrate that a sufficient number of random iterations can predict the generation of new macro-lineages when the number of sites in X is large enough. These results provide a crucial theoretical basis for understanding the evolution of SARS-CoV-2.

3,4-Dihydroquinolin-2(1H)-ones represent a class of valuable bioactive compounds with six-membered nitrogen-containing heterocyclic structures. The development of simple, mild and efficient synthetic methods has been widely concerned by synthetic chemists. In this review, we have summarized a series of different synthetic strategies for the synthesis of dihydroquinoline-2(1H)-ones via catalytic annulation of α,β-unsaturated N-arylamides in the past decade, including covering electrophilic cyclization, radical initiated cyclization and photochemical cyclization reactions. Besides, the substrate scope and mechanistic details are also discussed. This paper will provide a useful reference for the development of diverse synthesis methodologies of 3,4-dihydroquinolin-2(1H)-ones.

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P < 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

The surging electricity demand driven by a growing global population, coupled with the increasing electrification of industries, transportation, and power-intensive appliances, poses a substantial challenge to electricity systems worldwide. This challenge is further compounded by the pressing issue of climate change. To address climate change and mitigate the environmental consequences of fossil fuel use, renewable energy sources are expected to play a pivotal role. However, certain renewable sources, such as wind and solar, exhibit stochastic behavior, resulting in unpredictable power output and significant fluctuations. This intermittency presents a challenge in maintaining a stable and reliable power supply. To overcome this challenge and ensure a balanced electricity grid, the strategic deployment of energy storage devices throughout the power system becomes critically important. Energy storage technologies play a vital role in mitigating the mismatch between renewable power generation and consumption. Additionally, they enable the storage of surplus energy generated from renewable sources during periods of high production for later use during periods of low or no generation. Each technology possesses unique characteristics and applications, providing flexibility and diversity in energy storage solutions. This work provides an overview of different energy storage technologies and explores their role in establishing a sustainable power system.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

This paper outlines evidence-based practice in the context of professionalism, and highlights the contribution evidence-based practice can make to the professional practice of higher education course managers. Implications of the changing HE landscape for the status of academics as professionals are reviewed, and evidence-based practice is proposed as a solution for both enhanced course management and to remedy perceived deprofessionalisation. Finally, questions regarding researching professional practice within one’s own institution are addressed.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

It is expected that scholars will continue to strengthen the depth and breadth of theoretical research on RIS, so as to provide a higher theoretical upper bound for the engineering application of RIS. While making breakthroughs in academic research, great progress has been made in engineering application research and industrialization promotion. This article will provide an overview of RIS engineering applications, mainly including the typical features, typical classifications, and typical deployment scenarios of RIS. Then the challenges and candidate solutions of the RIS are systematically and deeply analyzed, involving the cascade channel decoupling for solving the RIS beamforming, the influences and solutions of RIS regulation constraints, RIS system architecture of network controlled mode, the integrated channel regulation and information modulation, TDD mechanism used for RIS. Future trends and challenges are also provided.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

We present here seven new zircon (U-Th)/He (ZHe) ages and three new zircon fission track ages (ZFT) analyzed from an age-elevation profile (Machu Picchu, Peru). ZFT data present older ages in comparison with the other thermochronological data, whereas the ZHe data interestingly present similar ages than the ones obtained with apatite (U-Th)/He (AHe). It has been proposed that He retention in zircon is linked to the damage dose, with an evolution of the closure-temperature from low values associated to low α-dose (<1016 α/g), subsequently increasing before decreasing again at very high α-dose (>1018 α /g). Studies have been focused on the He diffusion behavior at high α-dose, but little is known at low dose. We propose that the ZHe closure temperature at α-dose ranging from 0.6×1015 to 4×1016 α/g is in the range of ~60-80°C. This value is lower than the one proposed in the current damage model ZRDAAM and demonstrates that the ZHe and AHe methods could have similar closure temperatures at low α-dose (i.e. similar ages). These new data strengthen our previous geological conclusions and even highlight an about twice more important cooling rate than the one deduced from AHe and apatite fission-track data alone registered at Machu Picchu.

Thyroid nodules (TNs) are common thyroid lesions in older population. Few studies focused on the prevalence of TNs and its relationship to lifestyle characteristics and dietary habits in centenarians. The current study aimed to determine the prevalence of TNs in Chinese centenarians using high-resolution ultrasound equipment and investigate its relationship to lifestyles and dietary habits. The current study was part of China Hainan Centenarian Cohort Study (CHCCS) which conducted in Hainan, an iodine sufficient region in China. A total of 874 permanent residents aged 100 years or older (mean age, 102.8 ± 2.8 years) without any missing data were included in the analysis. Among the participants, 649 of them were detected at least one thyroid nodule under the ultrasound examinations. The overall prevalence rate of TNs was 74.3%. The prevalence of TNs was higher in participants who were females, hypertension, diabetes, and underweight than their counterparts. Multivariate logistic regression analyses showed that being female, hypertension, diabetes, betel quid consumption, red meat consumption were independent risk factors, while being underweight, and nut consumption were independent protective factors for TNs. Our findings indicate that the presence of thyroid nodules was highly prevalent in Chinese centenarians, particularly in females. In addition to gender, hypertension, diabetes, and underweight, the presence of TNs was independently associated with betel quid, red meat, and nut consumptions. Further prospective studies are warranted to verify these associations in population from different age strata, races, cultures, and iodine backgrounds.

Bacteria and archaea participate in and are influenced by processes of substance circulation and energy exchanges in natural environment. Generally, the community changes of bacteria and archaea in sediment are mainly driven by seasonality in mid-latitude regions. But in our study, water diversion to Fen river played a more important role on OTU number, diversity and community structure of bacteria and archaea in sediment than seasonal variation, which was found by 16S rRNA high-throughput sequencing technology. This phenomenon might be caused by external transferred water on the physicochemical water environment and accelerated release of positive nitrogen from sediment caused by rise of water level. Changes of carbon-nitrogen cycle and increase of electrical conductivity (EC) value induced more diversion-responders than season-responders both for bacteria and archaea. Seasonal changes have been influencing bacteria and archaea mildly throughout the whole study reach. After water diversion, the environment indicators relating to bacteria community obviously changed from nutrients to salinity while that for archaea almost disappeared. Our research showed the effects of human activities on the communities of bacteria and archaea outweigh the forcing from natural seasonal changes in mid-latitude regions and revealed the mechanism, highlighting different responses of bacteria and archaea to environmental changes.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

In the paper, a fully discrete compact difference scheme with $O(\tau^{2}+h^{4})$ precision is established by considering the numerical approximation of the one-dimensional Allen-Cahn equation. The numerical solutions satisfy discrete maximum principle under reasonable step ratio and time step constraint is proved. And the energy stability for the fully discrete scheme is investigated. An example is finally presented to show the effectiveness of scheme.

A mathematical model is proposed to analyze the spreading dynamics of COVID-19. By using the parameters of the model, namely the basic reproduction number (R0) and the attenuation constant (k), the daily number of infections (DNI) and the cumulative number of infections (CNI) are deduced and shown to be in good agreement with experimental data. This model effectively addresses three key issues: explaining the waveform pattern of DNI, predicting the occurrence of the second wave of infection, and understanding the competitive spread of two viruses in a region. The findings demonstrate that these significant challenges can be comprehensively tackled using a simple mathematical framework. The theoretical insights derived from this model hold potential in guiding the estimation of the severity of an infection wave and formulating effective strategies for the control and mitigation of epidemic outbreaks.

Phenacoccus manihoti (Hemiptera: Pseudococcidae), is an invasive pest that is very detrimental to cassava cultivation in Indonesia. Control efforts by utilizing natural enemies of the parasitoid have succeeded in overcoming the cassava mealybug in 25 countries such as in Africa and Thailand. The purpose of this study was to specifically evaluate the potential for parasitoid species associated with the mealybug P. manihoti by (1) determining the level of parasitization against mealybugs on various varieties of cassava, (2) determining parasitoid preference for P. manihoti instars, and (3) determining the type of parasitoid. This study was undertaken in the field to re-evaluate the kinds of parasitoids associated with cassava pests, and in the laboratory to assess the amount of parasitization, predilection, and functional response of parasitoids to P. manihoti population density. The findings revealed three of parasitoids linked with P. manihoti in the field: Anagyrus lopezi, Acerophagus sp., and Blepyrus sp. The parasitoid A. lopezi had the greatest parasitization rate in the field, which was 18.67 %. Furthermore, the parasitoids A. lopezi and Blepyrus sp. preferred 3rd instar nymphs, but Acerophagus sp. preferred 2nd instar nymphs. The parasitoid A. lopezi demonstrated a type-III functional response, while Acerophagus sp. and Blepyrus sp. demonstrated a type-II functional response. The handling capacity (Th) of A. lopezi is the shortest at 3.42 minutes. This work is a comprehensive study of the parasitoid A. lopezi's potential as a biological agent, highlighting how it effectively suppresses P. manihoti on various cassava varieties in Bali, providing an inexpensive, environmentally friendly, and applicable control in tropical countries.

Drone and aerial remote sensing images are widely used, but their imaging environment is complex and prone to image blurring. Existing CNN deblurring algorithms usually use multi-scale fusion to extract features in order to make full use of aerial remote sensing blurred image information, but images with different degrees of blurring use the same weights, leading to increasing errors in the feature fusion process layer by layer. Based on the physical properties of image blurring, this paper proposes an adaptive multi-scale fusion blind deblurred generative adversarial network (AMD-GAN), which innovatively applies the degree of image blurring to guide the adjustment of the weights of multi-scale fusion, effectively suppressing the errors in the multi-scale fusion process and enhancing the interpretability of the feature layer. The research work in this paper reveals the necessity and effectiveness of a priori information on image blurring levels in image deblurring tasks. By studying and exploring the image blurring levels, the network model focuses more on the basic physical features of image blurring. Meanwhile, this paper proposes an image blurring degree description model, which can effectively represent the blurring degree of aerial remote sensing images. The comparison experiments show that the algorithm in this paper can effectively recover images with different degrees of blur, obtain high-quality images with clear texture details, outperform the comparison algorithm in both qualitative and quantitative evaluation, and can effectively improve the object detection performance of aerial remote sensing blurred images. Moreover, the average PSNR of this paper's algorithm tested on the publicly available dataset RealBlur-R reached 41.02dB, surpassing the latest SOTA algorithm.

With the rapid development of the Internet of Things, massive amounts of data will be generated at the network edge, resulting in increased latency of the traditional cloud computing model. Cloud service providers deploy edge servers near the users to improve the quality of service. Due to the large scale of networks, the inefficiency of edge server deployment and task scheduling will result in excessive latency and severe workload imbalance among edge servers. In this paper, we propose a Server Deployment and Task Scheduling (SDTS) framework in multi-edge collaborative computing, which can effectively reduce latency and ensure workload balancing. First, a metropolitan area network (MAN) is divided into dense candidate regions (DCRs) based on the density characteristics of mobile end devices, and then servers are deployed independently in each sub-region. Then, a two-step clustering algorithm is designed to deploy servers as close as possible to the mobile devices. Finally, a task scheduling algorithm is presented based on an edge scheduling layer in DCRs, which can leverage collaboration between edge servers to improve the performance of the entire edge computing system. The experimental results based on the Cellular Base Station (CBS) dataset of Shanghai Telecom indicate that the proposed approach outperforms several representative strategies in terms of latency and workload balancing.

The hyper-arid environment is characterized by high inter-annual climatic fluctuations. The yearly average rainfall can change substantially for several years, forming wet or dry sub-periods. Observing rainfall trends over a sub-period can lead to a false perception of a change in the trend but may in fact represent a periodic cycle when examined on a larger time scale. We aimed to better characterize the rainfall regime prevailing in the hyper-arid Arava Valley (Israel/Jordan), and to examine the response of vegetation to annual rainfall. We hypothesized that annual and perennial vegetation would respond differently to wet and dry sub-periods, and that grazing activities will impact vegetation growth. We used a time series of monthly rainfall, from which we calculated Standard Precipitation Index (SPI), and calculated proxies of perennial and annual vegetation over the last four decades using Landsat-derived Normalized Difference Vegetation Index (NDVI). We found no clear trend in rainfall amounts during this period, however we did identify wet and dry sub-periods which were statistically distinct in rain and in vegetation patterns from each other. The highest levels of correlation between rainfall and the NDVI derived proxies were found when examining average rainfall over a period of two- three years for the annual vegetation and over four years for perennial vegetation. Using the Mann-Kendall test, we identified a time lag of two to four years, with the proxies of annual vegetation responding faster than the proxies of perennial vegetation, to shifts between wet and dry sub-period. In addition, we found a consistent difference between natural vegetation cover in Jordan (grazed) and Israel (non-grazed), favoring the development of natural vegetation on the Israeli side. We conclude that integrating between long-term remote sensing satellite imagery and climatic records revealed the greater resilience of perennial vegetation in the hyper-arid region to climatic fluctuation, and enabled us to identify the vegetation’s sensitivity to anthropogenic impact.

Based on the 2014-2015 China Education Panel Survey (CEPS) and using the propensity score matching method, we studied the causal relationship between physical exercise and prosocial behavior of junior middle school students in China. Ordinary least squares regression and propensity score matching estimation results showed that participation in physical exercise significantly increases students’ prosocial behavior by more than 0.2 standard points. The results of this study were tested and found to be robust.

This study describes KPC-204, a novel variant of Klebsiella Pneumoniae carbapenemase, characterized by a KDD amino acid insertion at Ambler position 269 deviates from KPC-2. This variant was identified in an ST11-type clinical isolate of carbapenem-resistant Klebsiella Pneumoniae from China. Notably, KPC-204 exhibits resistance to both ceftazidime-avibactam and carbapenems. Genetic analysis revealed that blaKPC-204 was located on a highly mobile IncFII/IncR plasmid within a complex genetic structure that facilitates its spread. Functional analysis, achieved through cloning into E. coli DH5α, validates KPC-204's contribution to increased resistance to ceftazidime-avibactam. The kinetic parameters showed that KPC-204 exhibited similar affinity to KPC-2 toward ceftazidime and reduced sensitivity to avibactam. Mating experiments demonstrated the resistance's transmissibility. This investigation underscores the evolving diversity of KPC variants affecting ceftazidime-avibactam resistance, highlighting the necessity for continuous monitoring.

A two-step, one-pot synthesis of 3-substituted 1H-dibenzo[e,g]indazoles in good to high yields via a LiOtBu-promoted intramolecular cyclization of 2’-alkynyl-biaryl-2-aldehyde N-tosylhydrazones, formed in situ by the reactions of 2’-alkynyl-biaryl-2-aldehydes with p-methylbenzenesulfonohydrazide was developed. Two kinds of hydrogen bonds forming in several products were observed in DMSO-d6 solution in 1H NMR spectroscopic data, which were assigned to the formation of solvated products and dimers of products, supported by the studies of density functional theory (DFT).

The COVID-19 pandemic resulted in government restrictions that altered the lifestyle of people worldwide. Studying the impact of these restrictions on exercise behaviors will improve our understanding of environmental factors that influence individuals’ PA. We conducted a retrospective analysis using an index of government pandemic stringency developed by Oxford and a wearable device for runners to compare strictness of lockdowns and exercise habits, using digitally-logged PA data from more than 7,000 runners on a global scale. Additionally, time-of-day of PA globally and levels of PA in 14 countries are compared between the pre-pandemic year of 2019 and the first pandemic year of 2020. We found that during the pandemic the time-of-day that people exercised experienced a major shift, with significantly more activities logged during standard working hours on workdays (p<0.001) and fewer during the same time frame on weekends (p<0.001). Of the countries examined, Italy and Spain had among the most strict lockdowns and suffered the largest decreases in activity counts, whereas France experienced a minimal decrease in activity counts despite enacting a similarly strict lockdown. This study suggests that there are several factors affecting PA, including government policy, workplace policy, and cultural norms.

The current urban environment is faced with the potential threat of frequent natural disasters, and the sustainable development of post-disaster community has become a global issue. As an intrinsic motivation influencing the social interaction and capital operation of community, social network is an important mechanism promoting such sustainable development. However, the difference in social network caused by different member structure, spatial arrangement and management mechanism of post-disaster communities in different reconstruction modes has influenced such sustainable development process. Therefore, reasonable selection of reconstruction mode is crucial. This paper applied analytic hierarchy process to comprehensively measure and compare the social network strength in post-disaster communities in the four reconstruction modes adopted by the government of China, i.e. unified planning and unified construction, unified planning and independent construction, in situ reconstruction and relocation resettlement, with communities after the 2008 Sichuan earthquake in Chengdu, China as study objects from the perspective of three social relations (the relations between residents and residents, residents and managers, and residents and servers). The results showed that strong connections are generally presented in the social network of post-disaster communities in unified planning modes, that the strength is significantly higher than that of those in non-unified planning modes, and that the strength of UPIC communities is the highest. Meanwhile, government intervention, residents’ free participation and market operation are positively correlated to government trust, community interaction and community service respectively. The positive impact of government intervention is the most significant, but it has a peak value. No government management and excessive government intervention will exert negative impacts. The coordination of government, society and market is the key contents of post-disaster community reconstruction. The reconstruction modes based on “government leadership, resident participation and market operation” may become a feasible path for such sustainable development.

In present work, the effects of bioflavonoids (ginkgetin and sciadopitysin) on stimulus-induced superoxide generation, tyrosyl and serine/threonine phosphorylation of proteins in human neutrophils, and the translocation of cytosolic compounds (p47phox, p67phox and Rac) to cell membrane were studied, which were isolated from the needles of Taxus media var. Hicksii. Meanwhile, three normal flavonoids (apigenin, quercetin and isoquercetin) were involved as contrasts. The results indicated that ginkgetin and sciadopitysin were capable of concentration-dependently inhibitory effects on the superoxide generation induced by N-formyl-methionyl-leucyl-phenylalanine (fMLP), arachidonic acid (AA) and phorbol-12-myristate 13-acetate (PMA). And they also suppressed fMLP- and AA- induced tyrosyl or PMA-induced serine/threonine phosphorylation and the translocation of cytosolic compounds (p47phox, p67phox and Rac) to cell membrane, which were in parallel with the suppression of the stimulus-induced superoxide generation. The effect of these compounds on the radical-scavenging was also investigated. Ginkgetin and sciadopitysin did not show remarkable effect on DPPH radical-scavenging activity, and they didn’t display the radical-scavenging activity on superoxide anion generated by phenagine methoxysulfate (PMS)-NADH system. Apparently, ginkgetin and sciadopitysin had great performance in pharmacological value and they are worthy of in-depth study.

: Sputtering of silicon in a Helium magnetron discharge (MS) has been reported as a bottom-up procedure to obtain He-charged silicon films (i.e. He nanobubbles encapsulated in a silicon matrix). The incorporation of heavier noble gases is demonstrated in this work with a synergistic effect producing increased Ne and Ar incorporations when using He-Ne and He-Ar gas mixtures in the MS process. Microstructural and chemical characterizations are reported by ion beam analysis (IBA) and scanning and transmission electron microscopies (SEM and TEM). In addition to gas incorporation, helium promotes the formation of larger nanobubbles. For the case of Ne high resolution X-ray photoelectron and absorption spectroscopies (XPS and XAS) are reported with remarkable dependence of the Ne 1s photoemission and the Ne K-edge absorption on the nanobubbles size and composition. The gas (He, Ne, Ar) charged thin films are proposed as “solid” targets for the characterization of spectroscopic properties of noble gases in a confined state without the need for cryogenics or high-pressure anvils devices. Also their use as targets for nuclear reaction studies is foreseen.

Wobbling motion as an exotic collective mode in nuclei without axial symmetry, was intensively discussed during the last few years. The observation of the newly proposed transverse wobbling, first reported in $^{135}$Pr and soon after in nuclei from other mass regions, was considered as a significant discovery in low-spin nuclear structure. However, both the reported experimental results and the proposed theoretical models were lively questioned in a series of works devoted to the investigation of the low-spin wobbling mode in the same nucleus. The electromagnetic properties of the $\Delta I=1$ transitions connecting the one- to zero-phonon and the two- to one-phonon wobbling bands in $^{135}$Pr were recently remeasured, demonstrating their predominant $M1$ magnetic character which is in contradiction with the wobbling motion interpretation. These new experimental observables being well reproduced by both quasiparticle-plus-triaxial-rotor model and interacting boson-fermion model calculations, are against the previously proposed wobbling characteristics of the low-spin bands in $^{135}$Pr. On the other hand, we obtained conclusive experimental evidence for the theoretically suggested transverse wobbling bands at medium spin in $^{136}$Nd. The comparison of the experimental data with calculations utilizing the triaxial projected shell model and a new developed particle-rotor model with frozen orthogonal geometry of the active nucleons, supports the description in terms of transverse wobbling of medium-spin bands in triaxial even-even nuclei.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

This work is a natural extension of the author’s previous work: “Multiple scattering theory for heterogeneous elastic continua with strong property fluctuation: theoretical fundamentals and applications” (arXiv:1706.09137 [physics.geo-ph]), which established the foundation for developing multiple scattering model for heterogeneous elastic continua with either weak or strong fluctuations in mass density and elastic stiffness. Polycrystalline material is another type of heterogeneous materials that widely exists in nature and extensively used in industry. In this work, the corresponding multiple scattering theory for polycrystalline materials with randomly oriented anisotropic crystallites is developed. To validate the theory, the theoretical results for a series of materials such as OFHC copper, 304 stainless steel, and Inconel 600 are compared to experimental measurements and the numerical results obtained using finite element simulations. Detailed analysis shows that the new theory is capable of predicting the dispersion and attenuation of polycrystals with satisfactory accuracy. The results also show the new model can give an estimate on the average grain size with a relative error equal to or less than ten percent. As applications in ultrasonic nondestructive evaluation, we calculated the dispersion and attenuation coefficient of one of the most important polycrystalline materials in aeronautics engineering: high-temperature titanium alloys. The effects of grain symmetry, grain size, and alloying elements on the dispersion and attenuation behaviors are examined. Key information is obtained which has significant implications for quantitatively evaluating the average grain size, monitoring the phase transition, and even estimating gradual change in chemical composition of titanium components in gas turbine engines. For applications in seismology, the velocities and Q-factors for both hexagonal and cubic polycrystalline iron models for the Earth’s uppermost inner core are obtained in the whole frequency range. Using the realistic material parameters of iron under the high temperature and high-pressure conditions calculated from ab initio simulations, the numerical results show that the Q-factors range from 0.001 to 0.05, which shows good agreement with that inferred from real seismic data. The new model predicts the velocity of longitudinal waves varies between ± 1% to ± 5 % relative to the Voight average velocity, while the velocity of transverse waves varies from ± 10% to ± 20%, which gives promising explanation to the abnormally slow transverse velocity observed in practical measurements. The numerical results support the conjecture that the Earth’s uppermost inner core is a solid polycrystalline medium. The comprehensive numerical examples show the new model is capable of capturing the most important scattering features of both ultrasonic and seismic waves with satisfactory accuracy. This work provides a universal, quantitative model for characterization of a large variety of polycrystalline materials. It also can be extended to incorporate more complicated microstructures, including ellipsoidal grains with or without textures, and even multi-phase polycrystalline materials. The new model demonstrates great potential of applications in ultrasonic nondestructive evaluation and inspection of aerospace and aeronautic structures. It also provides a theoretical framework for quantitative seismic data explanation and inversion for the material composition and structural formations of the Earth’s inner core.

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous elastic continua with strong property fluctuation and obtained the exact solution to the dispersion equation under the first-order smoothing approximation. The model establishes an accurate quantitative relation between the microstructural properties and the coherent wave propagation parameters and can be used for characterization or inversion of microstructures. Starting from the elastodynamic differential equations, a system of integral equation for the Green functions of the heterogeneous medium was developed by using Green’s functions of a homogeneous reference medium. After properly eliminating the singularity of the Green tensor and introducing a new set of renormalized field variables, the original integral equation is reformulated into a system of renormalized integral equations. Dyson’s equation and its first-order smoothing approximation, describing the ensemble averaged response of the heterogeneous system, are then derived with the aid of Feynman’s diagram technique. The dispersion equations for the longitudinal and transverse coherent waves are then obtained by applying Fourier transform to the Dyson equation. The exact solution to the dispersion equations are obtained numerically. To validate the new model, the results for weak-property-fluctuation materials are compared to the predictions given by an improved weak-fluctuation multiple scattering theory. It is shown that the new model is capable of giving a more robust and accurate prediction of the dispersion behavior of weak-property-fluctuation materials. Numerical results further show that the new model is still able to provide accurate results for strong-property-fluctuation materials while the weak-fluctuation model is completely failed. As applications of the new model, dispersion and attenuation curves for coherent waves in the Earth’s lithosphere, the porous and two-phase alloys, and human cortical bone are calculated. Detailed analysis shows the model can capture the major dispersion and attenuation characteristics, such as the longitudinal and transverse wave Q-factors and their ratios, existence of two propagation modes, anomalous negative dispersion, nonlinear attenuation-frequency relation, and even the disappearance of coherent waves. Additionally, it helps gain new insights into a series of longstanding problems, such as the dominant mechanism of seismic attenuation and the existence of the Mohorovičić discontinuity. This work provides a general and accurate theoretical framework for quantitative characterization of microstructures in a broad spectrum of heterogeneous materials and it is anticipated to have vital applications in seismology, ultrasonic nondestructive evaluation and biomedical ultrasound.

The geometry of mesoscopic inhomogeneities plays an important role in determining the macroscopic propagation behaviors of elastic waves in a heterogeneous medium. Non-equiaxed inhomogeneities can lead to anisotropic wave velocity and attenuation. Developing an accurate scattering theory to describe the quantitative relation between the microstructure features and wave propagation parameters is of fundamental importance for seismology and ultrasonic nondestructive characterization. This work presents a multiple scattering theory for strongly scattering elastic media with general tri-axial heterogeneities. A closed analytical expression of the shape-dependent singularity of the anisotropic Green’s tensor for the homogeneous reference medium is derived by introducing a proper non-orthogonal ellipsoidal coordinate. Renormalized Dyson’s equation for the coherent wave field is then derived with the help of Feynman’s diagram technique and the first-order-smoothing approximation. The exact dispersion curves and the inverse Q-factors of coherent waves in several representative medium models for the heterogeneous lithosphere are calculated numerically. Numerical results for small-scale heterogeneities with the aspect ratio varying from 1 to 7 show satisfactory agreement with those obtained from real earthquakes. The results for velocity dispersion give rise to a novel explanation to the formation mechanism of different seismic phases. The new model has potential applications in seismology and ultrasonic microstructure characterization.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

The paper studies some cases in physics such as Galilean inertia motion and etc., and presents a logical schema of recursive abduction, from which we can derive the universality of physical laws in an effective logical path without requiring infinite inductions. Recursive abduction provides an effective logical framework to connect a universal physical law with finite empirical observations based on both quasi-law tautologies and suitable recursive dimensions, two new concepts introduced in this paper. Under the viewpoint of recursive abduction, the historical difficulty from Hume’s problem naturally vanishes. In Hume’s problem one always misunderstood a time-recursive issue as an infinitely inductive problem and, thus, sank into an inescapable quagmire. With this new effective logical schema, the paper gives a concluding discussion to Hume’s problem and justifies the validity of probability argument for natural laws.

The digital orthophoto is an image with geometric accuracy and no distortion. It is acquired through a top view of the scene and finds widespread applications in map creation, planning, and related fields.This paper classifies the algorithms for digital orthophoto generation into two groups: explicit methods and implicit methods. Explicit methods rely on traditional geometric methods, obtaining geometric structure presented by explicit parameters with Multi-View Stereo (MVS) theories, as seen in our proposed Top view constrained Dense Matching (TDM). Implicit methods rely on neural rendering, obtaining implicit neural representation of scenes through the training of neural networks, as exemplified by Neural Radiance Fields (NeRF). Both of them obtain digital orthophoto by rendering from a top view perspective. In addition, this paper conducts an in-depth comparative study between explicit and implicit methods. The experiments demonstrate that both algorithms meet the measurement accuracy requirements and exhibit a similar level of quality in terms of generated results. Importantly, the explicit method shows a significant advantage in terms of efficiency, with a time consumption reduction of two orders of magnitude under our latest CUDA version TDM algorithm. Although explicit and implicit methods differ significantly in their representation forms, they share commonalities in the implementation across algorithmic stages. These findings highlight the potential advantages of explicit methods in orthophoto generation, while also providing beneficial references and practical guidance for the fast digital orthophoto generation using implicit methods.

Electric energy has become essential nowadays not only for the daily life of each of us but also for the economy of different countries. The dissemination of geographic information plays an important role in national development as it facilitates communication between managers, investors, and consumers in this sector. Since the management of electricity network data was previously done in Tunisia based on paper maps and plans, the purpose of this article is to present a case of planning based on GIS, Web, and 3D Web GIS, which would have significant positive consequences on this sector from a technical and financial sides with an improvement in customer satisfaction and the creation of an intelligent electricity network which will be a real decision-making tool. This work draws up an inventory of the network MV (Medium Voltage)/LV (Low Voltage) of the region of Medjez El Bab which routes electricity to the big centers of consumption with access to MV/LV subscribers. The analysis of the network's impedance allowed carrying out different scenarios to optimize performance and obtain more realistic routes. Many thematic maps were produced as part of this project (Slope map, Land use map, map of the MV voltage domains, map of the MV/LV transformer stations power, etc.). A three-dimensional virtual city has been developed to visualize the graphical and attribute data for the study area. A Web and 3D Web GIS applications that allows the publication of the interactive maps on the Web as well as the database information have been developed to offer users the possibility of consulting the produced products by internet. Finally, a website related to the study was developed.

Translation is spatiotemporally regulated and ER-associated mRNAs are generally in efficient translation. It is unclear whether the ER-associated mRNAs are deadenylated or degraded on the ER surface in situ or in the cytosol. Here, we showed that ER possessed active deadenylases, particularly the poly(A)-specific ribonuclease (PARN), in common cell lines and mouse tissues. Consistently, purified recombinant PARN exhibited a strong ability to insert into the Langmuir monolayer and liposome. ER-anchored PARN was found to be able to reshape the poly(A) length profile of the ER-associated RNAs by suppressing long poly(A) tails without significantly influencing the cytosolic RNAs. The shortening of long poly(A) tails did not affect global translation efficiency, suggesting that the non-specific action of PARN towards long poly(A) tails was beyond the scope of translation regulation on the ER surface. Transcriptome sequencing analysis indicated that the ER-anchored PARN trigged the degradation of a small subset of ER-enriched transcripts. The ER-anchored PARN modulated the translation of its targets by redistributing ribosomes to heavy polysomes, suggesting that PARN may play a role in dynamic ribosome reallocation. During DNA damage response, MK2 phosphorylated PARN-Ser557 to modulate PARN translocation from the ER to cytosol. By promoting the decay of ER-associated MDM2 transcripts with low ribosome occupancy, the ER-anchored PARN modulated DNA damage response and thereby cell viability. These findings revealed that a highly regulated communication between mRNA degradation rate and translation efficiency is present on the ER surface in situ and that PARN may contribute to this communication by modulating the dynamic ribosome reallocation between transcripts with low and high ribosome occupancies.

The efficient extraction of phthalate acid esters (PAEs) is challenging due to their extremely low concentration, complicated matrices and hydrophilicity. Herein, hol-low microspheres, as an ideal coating, possesses significant potential for solid-phase microextraction (SPME) due to their fascinating properties. In this study, multi-walled carbon nanotubes hollow microspheres (MWCNTs-HMs) were utilized as a fiber coating for the SPME of PAEs from tea beverages. MWCNTs-HMs were ob-tained by dissolving the polystyrene (PS) cores with organic solvents. Interestingly, MWCNTs-HMs well maintain the morphology of the precursors MWCNTs@PS. The layer-by-layer (LBL) assembly of MWCNTs on PS microsphere templates was ac-quired through electrostatic interactions. Six PAEs, di-ethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-2-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DOP), were se-lected as target analytes for assessing the efficiency of the coating for SPME. The stirring rate, sample solution pH and extraction time were optimized by using the Box-Behnken design. Under optimal working conditions, the proposed MWCNTs-HMs/SPME was coupled with gas chromatography-tandem mass spec-trometry (GC-MS/MS) to achieve high enrichment factors (118–2137), wide linearity (0.0004-10 μg L-1), low limits of detection (0.00011-0.0026 μg L-1) and acceptable recovery (80.2%-108.5%) for the detection of PAEs. Therefore, the MWCNTs-HMs coated fibers are promising alternatives in the SPME method for the sensitive detec-tion of PAEs at trace levels in tea beverages.

Cloud Manufacturing (CMfg) has attracted lots of attention from scholars and practitioners. The purpose of quality of service (QoS)-aware manufacturing cloud service composition (MCSC), as one of the key issues in CMfg, is to combine different available manufacturing cloud services(MCSs) to generate an optimized MCSC that can meet diverse requirements of customers. However, many available MCS, deployed in the CMfg platform, have same function but different QoS attributes. It is a great challenge to achieve optimal MCSC with high QoS. In order to obtain better optimization results efficiently for the QoS-MCSC problems, a whale optimization algorithm(WOA) with adaptive weight, Lévy flight, and adaptive crossover strategies (ASWOA) is proposed. In the proposed ASWOA, the adaptive crossover inspired by the genetic algorithm is developed to balance the exploration and exploitation. The Lévy flight is designed to expand the search space of WOA and accelerate the convergence of WOA with adaptive crossover. The adaptive weight is developed to extend the search scale of the exploitation. Simulation and comparison experiments are conducted on different scale QoS-MCSC problems. The experimental results demonstrate that the proposed ASWOA outperforms other compared cutting-edge algorithms.

Research has shown that the consumption of herbal teas is linked with positive effects on the regulation of postprandial blood glucose level. In this study, a comparative analysis of aqueous and ethanol extractions is performed on four herbal teas (Mallotus, Cyclocarya, Rubus, Vine) to evaluate their phytochemical profiles and functional activities. Investigations of phytochemical contents, antioxidant activities, α-glucosidase inhibitory activities and chemical compositions are carried out through colorimetric analyses and UPLC-Q-Orbitrap HRMS/MS, respectively. Results showed that among the studied herbal teas, Vine exhibited the highest glucose re-gulating abilities under both aqueous and ethanol extractions. Overall, ethanol extracted samples yielded higher phytochemicals content, but the compositions of the phytochemicals varied. Meanwhile, aqueous extracts showed surprisingly strong antioxidant activities and comparable α-glucosidase inhibitory activities with ethanol extracts. Phytochemicals contents presented a positive correlation with antioxidant activities and α-glucosidase inhibitory activities. Nevertheless, antioxidant activities displayed a weak positive correlation with α-glucosidase inhibitory activities. Results from this study provided evidence that aqueous extracts from herbal teas possessed valuable phytochemicals composition for antioxidants and the hyperglycemic populations, and are promising candidates for potential applications as functional ingredients with health promoting effects and as natural additives to boost the nutritional value of herbal food products.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

This paper provides the numerical investigation of two-dimensional stochastic Navier-Stokes equation driven by additive white noises. The vorticity-stream function method is presented to calculate the incompressible fluid flow. In order to solve the formulation of steam function equation, we propose a Crank-Nicolson Fourier pseudo-spectral method. Numerical results obviously show that the presence of stochastic forcing can have an impact upon the shapes of vortex in fluid flow. To a certain extent, the phenomenon of eddy shedding and the formation of some new vortex in a random medium can be observed, which make it possible for us to conduct optimal control experiments in the development of vortex structures.

Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the causative agent of coronavirus disease 2019 (COVID-19) continues to wreak havoc threatening the public health services and imposing economic collapse worldwide. Tailoring public health responses to the SARS-CoV-2 pandemic depends on understanding the mechanism of viral replication, disease pathogenesis, and accurately identifying acute infections and mapping the spreading risk of hotspots across the globe. However, effective identification and isolation of persons with asymptomatic and mild SARS-CoV-2 infections remain the major obstacles to efforts in controlling the SARS-CoV-2 spread and hence the pandemic. Understanding the mechanism of persistent viral shedding, reinfection, and the post-acute sequalae of SARS-CoV-2 infection (PASC) is crucial in our efforts to combat the pandemic and provide better care and rehabilitation to survivors. Here we present a living literature review on SARS-CoV-2 viral persistence, reinfection and PASC. We also highlight potential areas of research to uncover putative links between viral persistence, intra-host evolution, host immune status, and protective immunity to guide and direct future basic science and clinical research priorities.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

Panax notoginseng (Burk.) F. H. Chen, a valuable Chinese herb in Yunnan Province, is susceptible to leaf spot caused by Boeremia linicola. Nonetheless, effective control methods against leaf spot in P. notoginseng are lacking. We surveyed understorey P. notoginseng bases in Lincang, Lancang, and Xundian, with incidence rate reaching 80% and an average disease index of 25 in severe cases. We found that pathogenic bacteria overwinter in infected leaves and soil, with conidia and conidiophores serving as the primary infection source. The strain B. linicola LYB-2 showed the best growth at 20°C and pH 5.0. We also screened control agents using the plate and face-off culture methods. Tetramycin exhibited 38.56–74.67% inhibition with an EC50 of 0.60 mg/L. Copper abietate showed 3.10–34.76% inhibition with an EC50 of 3,120.05 mg/L. Trichoderma atroviride and T. harzianum exhibited inhibition rates of 52.48% and 44.19%, respectively, while Bacillus subtilis reached 78.45%. Field tests demonstrated significant control effects with 20% copper abresinate, B. subtilis, T. virenceae BH-10 preparation, and 0.3% tetramycin, achieving 82.57%, 72.56%, 71.3%, and 70.2% inhibition, respectively. These findings support their eco-friendly use for preventing and controlling leaf spot disease in P. notoginseng forests; we provide vital scientific evidence for disease prediction and green control strategies.

An essential step in solving any topology optimization problem is determining the sensitivities of the objective function and optimization constraints. Unfortunately, these sensitivities are usually derived and implemented manually. Nontrivial objective functions and constraints, especially with the involvement of material and geometric nonlinearities, need strenuous mathematical derivation, leading to error-prone implementation. Another intriguing approach to finding sensitivities is automatic differentiation. This paper uses the automatic differentiation and adjoint method to find the sensitivities for two multiphysics topology optimization problems: 1) thermoelasticity and 2) piezoelectricity. This approach is not limited to these examples and can be easily extended to other single- or multi-physics topology optimization problems.

Soft set theory is a mathematical tool for dealing with uncertainty. This paper investigates limits of interval type of soft sets (for short, it-soft sets). The concept of it-soft sets is first introduced. Then, limits of it-soft sets are proposed and their properties are obtained. Next, point-wise continuity of it-soft sets and continuous it-soft sets are discussed. Finally, an application for rough sets is given.

Pruning is one of the most important tree fruit production activities, which is highly dependent on human labor. Skilled labor is in short supply, and the increasing cost of labor is becoming a big issue for the tree fruit industry. Growers are motivated to seek mechanical or robotic solutions for reducing the amount of hand labor required for pruning. This paper reviews the research and development of sensing and automated systems for branch pruning for tree fruit production. Horticultural advancements, pruning strategies, 3D structure reconstruction of tree branches, as well as practice mechanisms or robotics are some of the developments that need to be addressed for an effective tree branch pruning system. Our study summarizes the potential opportunities for automatic pruning with machine-friendly modern tree architectures, previous studies on sensor development, and efforts to develop and deploy mechanical/robotic systems for automated branch pruning. We also describe two examples of qualified pruning strategies that could potentially simplify the automated pruning decision and pruning end-effector design. Finally, the limitations of current pruning technologies and other challenges for automated branch pruning are described, and possible solutions are discussed.

Dual quaternions have wide applications in automatic differentiation, computer graphics, mechanics and others. Due to its application in control theory, the matrix equation AXB=C has been extensively studied. However, there is currently limited information on matrix equation AXB=C over the dual quaternion algebra. In this paper, we provide the necessary and sufficient conditions for the solvability of the dual quaternion matrix equation AXB=C, and present the expression for the general solution when it is solvable. As an application, we derive the ϕ-Hermitian solutions for the dual quaternion matrix equation AXAϕ=C, where the ϕ-Hermitian extends the concepts of Hermiticity and η-Hermiticity. Lastly, we present a numerical example to verify the main research results of this paper.

In this work,the wave behaviour propagation of single-walled fluid conveying carbon nanotubes (SWCNT) under longitudinal magnetic fields and elastic foundations is studied, based on the nonlocal strain gradients theory(NSGT). With considertion of surface effect, the governing differential equation are obtained utilising Timoshenko beam theory and Hamilton's variational principle. The influence of small-scale parameters, fluid density, magnetic flux, surrounding elastic medium and surface effects on wave behaviour characteristics of carbon nanotubes are discussed in detail. The numerical results illustrated that with the magnetic flux increase，the phase velocities of the carbon nanotube will increase. When the fluid effects inside the carbon nanotube, the wave frequencies of the system reduces with increase in the non-local coefficient, while promotes with increase in the strain gradient coefficient. In addition, fluid density, surrounding elastic medium and surface effects have meaningful influence on the phase velocity of the system.

Up-conversion nanoparticles (UCNP) under near-infrared (NIR) light irradiation have been well investigated in the field of bio-imaging. However, the low up-conversion luminescence (UCL) intensity limits applications. Plasmatic modulation has been proposed as an effective tool to adjust the luminescence intensity and lifetime. In this study discrete dipole approximation (DDA) was explored concerning guiding the design of UCNP@mSiO2-Au structures with enhanced UCL intensity. The extinction effects of gold shells could be changed by adjusting the distance between the UCNPs and the Au NPs by synthesized tunable mesoporous silica (mSiO2) spacers. Enhanced UCL was obtained under 808 nm irradiation. Theoretical predictions could not be demonstrated to full extend by experimental data, indicating that better models for simulation need to better take into account inhomogeneities in particle morphologies.

This paper addresses the problem of assessing and optimizing acoustic positioning system for underwater target localization with range measurements only. We present a new three-dimensional assessment model to assess the optimal geometric beacon formation whether meet user needs. For the sake of mathematical tractability, it is assumed that the measurements of the range between the target and beacons are corrupted with white Gaussian noise with variance is distance-dependent. Then by adopting dilution of precision (DOP) parameters in the assessment model, the relationship between DOP parameters and positioning accuracy is derived. In addition, the optimal geometric beacon formation that will yield the best performance is achieved by minimizing the values of geometric dilution of precision (GDOP) on condition that the position of target is known and fixed. Next, in order to make sure whether the estimate positioning accuracy over interesting region satisfy the precision needed by the users, geometric positioning accuracy (GPA), horizonal positioning accuracy (HPA) and vertical positioning accuracy (VPA) are utilized to assess the optimal geometric beacon formation. Simulation examples are designed to illustrate the exactness of the conclusion. Unlike other work which only use GDOP to optimize the formation and cannot assess the performance of the specified dimensions, this new three-dimensional assessment model can assess the optimal geometric beacon formation in each dimension for any point in three-dimensional space, which can provide users with guidance advices to optimize performance of every specified dimension.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Currently, an interactive environmental planning analysis system platform based on " Three Lines One Permit " (TLOP) is being developed to support environmental planning, construction project approval, and the application of TLOP outcome data in Guangzhou. The main objective is to provide governments, businesses and the public with environmental planning analysis tools to determine the site of construction projects. The platform is using the system architecture of the browser and server. Its core functions are interactive environmental planning analysis tool for construction project and the results display tool supporting map viewing. It provides users with a large number of detailed geospatial data and TLOP results data access and environmental planning analysis functions. This article describes the system architecture and implementation of the system platform and has a case study illustrating the system functionality. At present, the platform has been deployed and trial-operated. The content of the analysis framework is constantly expanding. This promotes the matching of environmental planning and analysis with local conditions. This will implement the application of TLOP and improve the efficiency of project construction and the level of ecological environment planning and management.

Neural decoding from spiking activity is an essential tool for understanding the information encoded in population neurons, especially in applications like brain-computer interface (BCI). Various quantitative methods have been proposed and have shown superiorities under different scenarios respectively. From the machine learning perspective, the decoding task is to map the high-dimensional spatial &amp; temporal neuronal activity to the low-dimensional physical quantities (e.g., velocity, position). Because of the complex interactions and the abundant dynamics among neural circuits, good decoding algorithms usually have the capability of capturing flexible spatiotemporal structures embedded in the input feature space. Recently, the Transformer-based models are widely used in processing natural languages and images due to its superior performances in handling long-range and global dependencies. Hence, in this work we examine the potential applications of Transformers in neural decoding and introduce two Transformer-based models. Besides adapting the Transformer to neuronal data, we also propose a data augmentation method for overcoming the data shortage issue. We test our models on three experimental datasets and their performances are comparable to the previous state-of-the-art (SOTA) RNN-based methods. In addition, Transformer-based models show increased decoding performances when the input sequences are longer, while LSTM-based models deteriorate quickly. Our research suggests that Transformer-based models are important additions to the existing neural decoding solutions, especially for large datasets with long temporal dependencies.

In this paper, we consider a make-to-order supply chain which satisfies demand that is dependent on both price and quoted lead -time. The manufacturer chooses the lead -time and the order quantity, and the retailer sets the revenue shares. The interactions between the manufacturer and the retailer are modelled as a Nash Game, and the existence and uniqueness of pure strategy equilibrium are demonstrated. A mechanism that enables the supply chain to coordinate the decisions of the members is developed. Lastly, we also analyze how the supply chain system parameters impact the optimal supply chain decisions and the supply chain performance.

A modular switched-capacitor (SC) DC-DC converter (MSCC) is introduced in this paper. It is designed to boost a low input voltage to a high voltage level and can be applied for photovoltaics and electric vehicles. This topology has high extensibility for high voltage gain output. The merits of the converters also lie in the fault tolerance operation and the voltage regulation with a minimum change in the duty ratio. Those features are built in when designing the modules and then integrating these into the DC-DC converter. Converter performance including voltage gain, voltage and current stress are focused and tested. The converter is modelled analytically, and its control algorithm is analyzed in detailed. Both simulation and experiment are carried out to verify the topology under normal operation and fault mode operation.

Bearings are widely used in various types of electrical machinery and equipment. As their core components, failures will often cause serious consequences . At present, most methods of parameter adjustment are still manual adjustment of parameters. This adjustment method is susceptible to prior knowledge and easy to fall into the local optimal solution, failing to obtain the global optimal solution and requires a lot of resources.Therefore, this paper proposes a new method of bearing fault diagnosis based on wavelet packet transform and convolutional neural network optimized by simulated annealing algorithm.The experimental results show that the method proposed in this paper has a more accurate effect in feature extraction and fault classification compared with traditional bearing fault diagnosis methods. At the same time, compared with the traditional artificial neural network parameter adjustment, this paper introduces the simulated annealing algorithm to automatically adjust the parameters of the neural network, thereby obtaining an adaptive bearing fault diagnosis method. To verify the effectiveness of the method, the Case Western Reserve University bearing database was used for testing, and the traditional intelligent bearing fault diagnosis method was compared. The results show that the method proposed in this paper has good results in bearing fault diagnosis. Provides a new way of thinking in the field of bearing fault diagnosis in parameter adjustment and fault classification algorithms

The apple leaf-curling midge, Dasineura mali Kieffer (Diptera: Cecidomyiidae), is an invasive pest of apple. To provide crucial information for its pest risk analysis, forecast and management, we investigated the effects of temperatures (5, 10, 15, 20 and 25°C) and daylengths (10, 11, 12, 13, 14 and 15 hrs) on its development and survival. The midge could not complete its development at 10°C or lower. After transferred from 20°C to 10°C, mature larvae could survive for about two months and develop to adults. Pupation and emergence rates were significantly higher at 20°C than at 10°C and 25°C. Daylength had no effect on these parameters. The low temperature threshold and thermal requirement to complete development from eggs to adults were 3.7°C and 627 degree-days, respectively. The midge had significantly lower thermal requirement for completion of its lifecycle at 20°C (614.5 degree-days) than at 15°C (650.1 degree-days) and 25°C (634.8 degree-days). The thermal model developed in this study provided accurate predictions of the number of D. mali generations and adult emergence time in each generation in different regions of New Zealand. We suggest that the model could be used to predict population dynamics of this pest in other parts of the world.

Despite the rapid adoption of bilingual programs (English-Chinese) in China's higher education institutions (HEIs), concerns have been raised on perceived language hindrance to students’ academic comprehension and then performance. In response to this, this paper investigates the effects of bilingual instruction on content-based learning and provides empirical evidence after testing related influential factors in bilingual environment. Analyzing a sample of 498 undergraduate students enrolling in a fundamental business course in a sample university in China, we find insignificant statistical difference in students' academic performance between bilingual and L1 classes. We attribute this to the English language support provided by the university and show that learning competence can help students to minimize language barrier and furthermore solve the common learning problems confronted by both bilingual and L1 students. Overall, our paper aims to identify key determinants of students' academic performance in bilingual instruction and provide policy implication for developing desirable bilingual programs in HEIs.

Vein segmentation and projection correction constitute the core algorithms of auxiliary venipuncture device, responding to the accurate venous positioning to assist puncture and reduce the number of punctures and pain of patients. This paper proposes an improved U-Net for segmenting vein and a coaxial correction for image alignment in the self-build vein projection system. The proposed U-Net is embedded by Gabor convolution kernels in the shallow layers to enhance segmentation accuracy. Additionally, to mitigate the semantic information loss caused by channel reduction, the network model is lightweighted by the mean of replacing conventional convolutions with inverted residual blocks. During the visualization process, a method that combining coaxial correction and homography matrix is proposed to address the non-planarity of the dorsal hand in this paper. First, use a hot mirror to adjust the light paths of both projector and camera to be coaxial, and then align the projected image with dorsal hand using a homography matrix. Using this approach, the device requires only a single calibration before use. With the implementation of the improved segmentation method, an accuracy rate of 95.12% is achieved by the dataset. The intersection over union ratio between the segmented and original images is reached at 90.07%. The entire segmentation process is completed in a 0.09 second, and the largest distance error of vein projection onto dorsal hand is 0.53mm. Experiments show that the device has reached practical accuracy and has the value of research and application.

This paper proposes an encryption scheme for high pixel density images. Based on the application of the quantum random walk algorithm, the Long short-term memory (LSTM) can effectively solve the problem of low efficiency of the quantum random walk algorithm in generating large-scale pseudorandom matrices, and further improve the statistical properties of the pseudorandom matrices required for encryption. The LSTM is then divided into columns and fed into the LSTM in order for training. Due to the randomness of the input matrix, the LSTM cannot be trained effectively, so the output matrix is predicted to be highly random. The LSTM prediction matrix of the same size as the key matrix is generated based on the pixel density of the image to be encrypted, which can effectively complete the encryption of the image. In the statistical performance test, the proposed encryption scheme achieves an average information entropy of 7.9992, an average number of pixels changed rate (NPCR) of 99.6231%, an average uniform average change intensity (UACI) of 33.6029% and an average correlation of 0.0032. Finally, various noise simulation tests are also conducted to verify its robustness in real-world applications where common noise and attack interference are encountered.

Avian Influenza viruses (AIVs) has posed a significant pandemic threat since their discovery. This review mainly focuses on the epidemiology, virology, and pathogenesis, and treatments of avian influenza viruses. We delve into the global spread, past pandemics, clinical symptoms, severity, and immune response related to AIVs. The review also discusses various control measures, including antiviral drugs, vaccines, and potential future directions in influenza treatment and prevention. Lastly, by summarizing the insights from the previous pandemic control, this review aims to direct effective strategies for managing future influenza pandemics.

In real financial markets, the certainty equivalent rate is an important factor for investors to consider. From the value of a specific company’s certainty equivalent rate, investors can judge if this company is worth investing in. In this paper, we will explore how to obtain the value of the certainty equivalent rate so that we can evaluate a given company. First, we will introduce the theoretical support of this paper, which is put-call parity. From put-call parity, we will derive the mathematical expression for the certainty equivalent rate. Second, we will use the mathematical expression for the certainty equivalent rate to perform an empirical study. We will consider some extreme examples, including some of the best- and worst-performing stocks up to this point in 2023. Based on these stocks’ data, we will visualize the performance of these stocks and explain the meaning of the data. Finally, we will apply the results to a very popular industry—the electric vehicle industry—to explore the current electric vehicle market situation in the U.S.A.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

Abstract: The Micro-Electro-Mechanical System (MEMS) LiDAR point cloud in autonomous vehicles has a large deflection range, which results in slow registration speed and poor applicability. To maximize speed, an improved NDT (Normal Distribution Transform) method that integrates point cloud density features has been proposed. First, the point cloud is reduced using a modified voxel filter and a pass-through filter. Next, the ISS (Intrinsic Shape Signature) algorithm is utilized to analyze the point cloud features and extract keypoints, the 4PCS (4-Point Congruent Sets) algorithm is then employed to calculate the initial pose under the constraints of the keypoint set to complete the coarse registration. Finally, the self-adaptive segmentation model is constructed by using KD-tree to obtain the density features of keypoints, and the NDT algorithm is combined with this model to form an SSM-NDT algorithm, which is used for fine registration. Each algorithm was compared on the autonomous vehicle dataset PandaSet and actual collected data sets, the results show that the novel method increases the speed by at least 60% and takes into account good registration accuracy and strong anti-interference.

Graphene foam prepared by chemical vapor deposition method is a promising thermal interfacial material. However, the thermal properties of graphene foam highly depend on the experimental fabrication conditions during the chemical vapor deposition process. Aiming to reveal how to prepare the appropriate graphene foam for the various thermal management scenarios, the influence of experimental conditions on thermal properties of graphene foam is investigated. Furthermore, the contribution of thermal conductivity and thermal radiation to the effective thermal coefficient of graphene foam is carried out for comparison. Research results show that, the porosity and the cross-section shape of struts of growth template are two critical factors to affect the thermal transport of graphene foam, especially with the increase of temperature. In addition, the deposition time of graphene determines the wall thickness and affects the thermal conductivity directly. The thermal radiation contributes more than thermal conductivity when the temperature climbs continuously. Comparatively, the effective thermal coefficient of graphene foam composite with high porosity and circular shape struts is much superior to others at high temperature. The research findings can provide important guidance for the graphene foam fabrication and its applications in the field of thermal management.

Roadway accidents significantly contribute to intermittent congestion and increased CO2 emissions on freeways. This research introduces a statistical approach designed to predict the rise in CO2 emissions resulting from traffic disturbances or jams triggered by such incidents. It also assesses the influence of varying levels of accident management effectiveness in different situations. To construct these scenarios, the study employs VISSIM, a traffic modeling software, incorporating diverse factors such as traffic volume, vehicle types, incident durations, and freeway lane counts. It then produces traffic flow characteristics in the form of vehicle paths. The emission estimates are derived by correlating these simulated vehicle paths with emission rates from the MOVES model. The study then applies a regression analysis to examine the connection between the increase in emissions and various influencing factors. The findings indicate that this approach efficiently reflects the impact of variables like accident duration, vehicle mix, and traffic volume on CO2 emissions across different lane configurations. The accuracy of these predictions is also confirmed. The outcomes suggest the model's potential usage in guiding efforts to lower emissions and determining the optimal duration of incident management, particularly in terms of lane closure, to mitigate emission impacts. This paper also discusses the limitations of the model and the future improvement direction.

Change detection with heterogeneous remote sensing images (Hete-CD) plays an important role in practical applications, especially when homogenous remote sensing images are unavailable. However, bitemporal heterogeneous remote sensing images (HRSIs) cannot compare directly to measure change magnitude, and many deep learning methods require large amounts of samples to train the module. Moreover, labeling many samples for land cover change detection with HRSIs is time-consuming and labor-intensive. Therefore, acquiring satisfactory performance of Hete-CD remains a challenge for deep learning networks with very small training samples. In this study, we promote a novel deep-learning framework for Hete-CD to obtain satisfactory performance while the initial samples are very small. We initially design a multiscale network with select kernel-attention module to focus on capturing different change targets with various sizes and shapes. Then, a simple yet effective non-parametric sample-enhanced algorithm based on the Pearson correlation coeffi-cient is promoted to explore potential samples around each initial sample. Finally, the proposed network and sample-enhanced algorithm are fused into one iterative framework to improve the change detection performance with very small samples. Experimental results conducted on four pairs of actual HRSIs indicated that the proposed framework can achieve competitive accuracies with very small samples for initialization when compared with some state-of-the-art methods. For example, the improvement is approximately 3.38% and 1.99% when compared with the selected traditional methods and deep learning methods, respectively.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Rural landscapes are acknowledged for their potential to restore human health due to their natural characteristics. However, few studies have systematically analysed the impact of naturalness, landscape types, and combinations of landscape elements on restorativeness using both subjective and objective measurements. This study investigated the restorative effects of various rural landscapes in Guangzhou, employing electroencephalography and eye-tracking technologies to record physiological responses and using the Restorative Components Scale and the Perceived Restorativeness and Naturalness Scale to evaluate psychological responses. The results indicated the following: (1) There was a significant positive correlation between perceived naturalness and restorativeness, surpassing the impact of actual naturalness. (2) Different landscape types had a varying impact on mental health at the equal perceived naturalness. Natural forest landscapes and artificial forest landscapes exhibited the most substantial restorative effects among the natural and semi-natural landscapes examined, respectively, while settlement landscapes showed the highest restorative potential among the artificial landscapes. (3) Restorative properties varied across landscape elements, with identical elements yielding different benefits in different environments. Trees and water significantly enhanced restorativeness, whereas constructed elements such as roads and infrastructure reduced it. This study provides a scientific basis for restorative rural landscape design to enhance mental health and well-being.

An all-dielectric metasurface composed of orthogonal-slit silicon disks is proposed in this study. By modifying the unit structure of the metasurface with the bound states in the continuum (BIC) theory, a sharp Fano resonance can be generated. The resonance properties of the metasurface are investigated by analyzing the effects of the structural parameters on the resonance using the eigenmode analysis method. The Q factor and the resonance wavelength can be adjusted by varying the slit width, the disk thickness, and the disk radius. The electromagnetic characteristics and mechanism of the toroidal dipole-BIC (TD-BIC) are explored in depth through an analysis of the multipole expansion of the scattered power, along with the electromagnetic field and the current distribution at resonance. This research provides a novel approach for excitation of a strong TD-BIC resonance and proposes potential applications in optical switches, high-sensitivity optical sensors, and related areas.

Solute carrier (SLC) proteins transport a wide range of substrates across biological membranes and more than 400 proteins are considered as SLCs based on its sequence. Despite it has important potential applications in drug development, the SLC superfamily is still understudied. Drosophila blot, an orphan SLC protein, regulates F-actin organization in the syncytial blastoderm and the Malpighian tubules. However, the molecular mechanism was unknown. In this study, we found Blot was localized at the furrow canal, the front of the invaginating membrane during cellularization process. Blot is required for maintaining proper morphology of furrow canal and cellularization process. By affinity purification and mass spectrometry we identified RhoGEF ELMO/DOCK complex was required for Blot-mediated F-actin organization and cellularization. Further analysis revealed that ELMO localization depends on Blot. Taken together, we propose Blot plays a role in F-actin organization as an upstream factor of ELMO by recruiting ELMO to the target membrane compartments.

The early Paleozoic is a crucial period in the formation and evolution of the Eastern Kunlun Orogenic Belt (EKOB), and is of great significance for understanding the evolutionary history of the Proto-Tethyan Ocean. This paper presents new petrography, geochemistry, zircon U–Pb dating, and Lu–Hf isotopic research on the Yuejingshan gabbro from the eastern segment of the EKOB. Zircon U–Pb data suggests that the gabbro formed in the Early Silurian (435 ± 2 Ma). All samples have relatively low TiO₂ contents (0.45–2.97%), widely varying MgO (6.58–8.41%) and Mg^# (58–65) contents, and are rich in large ion lithophile elements (LILE such as Rb, Ba, Th, and U) and light rare earth elements (LREE). This indicates that it has a similar geochemical composition to island arc basalt. The major element features indicate that the formation of this gabbro underwent fractional crystallization of clinopyroxene, olivine, and plagioclase. The depletion of high field strength elements (HFSE, such as Nb, Ta, and Ti), and a slightly positive Hf isotope (with εHf_(t) ranging from 1.13 to 2.45) may be related to the partial melting of spinel-bearing peridotite, led by slab fluid metasomatism. The gabbro likely represents magmatic records of the latest period of the early Paleozoic oceanic crust subduction in the Eastern Kunlun. Therefore, the final closure of the Proto-Tethyan Ocean and the beginning of collisional orogeny occurred before the Early Silurian.

In recent years, frequent occurrences of low temperature disasters due to global climate change have significantly impacted the normal growth of crops. Research has indicated that inorganic selenium (which is more toxic) can not only enhance the effects of low temperature stress but also increase selenium content on plants; however, there is a scarcity of studies investigating the impacts of organic selenium and nano-selenium on crops. In order to investigate whether organic selenium and nano-selenium can enhance low-temperature tolerance and increase selenium content in pak choi (Brassica chinensis var. pekinensis. cv. ‘Suzhouqing’), different concentrations (0, 5, 10, 20 mg L-1) of exogenous selenium were applied in this experiment to assess their effects on plant growth, nutritional quality and antioxidant properties. RNA-Seq technology was used to sequence the transcriptome of the leaves. Based on the transcriptome data, a Weighted Gene Co-expression Network Analysis (WGCNA) was employed to construct a network that associates with physiological traits related to stress resistance. Two highly correlated gene co-expression modules were identified, and within them, nine hub genes associated with endocytosis, antioxidant stress, absorption, transport, and metabolism of selenium were discovered. The results indicated that the beneficial effects on yield and total selenium content under low temperature were attributed to (1) protection of photosynthetic pigments for enhancing photosynthetic capacity by the up-regulation of LHca2, LHcb1, LHca1, LHcb4 in KEGG pathway: photosynthesis-antenna proteins; (2) activation of antioxidant system for efficient ROS homeostasis such as SOD, POD and CAT by the genes such as Superoxide dismutase, Monodehydroascorbate and (3) selenium absorption by endocytosis, seleninum transportation by ABC transporter gene family and selenium metabolism related genes such as Cysteine synthase, Glutaredoxin. These findings provide a foundation for further investigation into the molecular mechanisms underlying the effects of organic selenium and nano-selenium on cyanochloride production at low temperatures.