This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

Postoperative adhesive arachnoiditis is an inflammatory response of the spinal leptomeninges that occurs after surgery, resulting in scar formation in the avascular nature of the arachnoid layer. Clinical manifestations of this condition include pain, sensory deficits, motor dysfunction, reflex abnormalities, and bladder/bowel impairments. In MRI scans, the signs of postoperative adhesive arachnoiditis can vary, but some specific indicators can assist surgeons in locating the lesion and planning surgical interventions more accurately. In this report, we reported a 37-year-old man with postoperative adhesive arachnoiditis after two surgeries for Chiari I malformation, demonstrating that the gradually-forming the delta cord sign with sequential syringomyelia. During the intraoperative examination, we identified the presence of the delta cord sign, which was formed by an arachnoid scar that was tethering the dorsal spinal cord to the dura. This discovery allowed us to precisely pinpoint the location of the arachnoid scar, thereby providing valuable guidance to avoid any unnecessary exploration of innocent structures during the procedure. Other localization signs were also reviewed.

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

Streptococcal infection is a main infectious diseases for farmed grey mullet (Mugil cephalus). This study were to identify spreptococcal species in diseased farmed grey mullet and to investigate differences in susceptibility to 13 antibiotics and in genotypes between the stains from the grey mullet and non-grey mullet. 170 samples from diseased farmed grey mullet were collected from three county in 2013 -2016. Multiplex PCR identified L. garviea (146) as the main pathogen, S. agalactia (9), S. dysgalactiae (19), and double infection (5), but no S. iniae. The prevalence changed annually and differed among three counties. Pulsed-field gel electrophoresis (PFGE) analysis demonstrated identical genotype with an ApaI-digested DNA pattern. Disc diffusion results demonstrated differences in antibiotic susceptibility between the strains from grey mullet (146) and non-grey mullet (30). Almost all strains resisted to clindamycin and all strains were susceptible to six antibiotic in grey mullet and 4 antibiotics in non-grey mullet. The reduced susceptible strains was more in non-grey mullet than grey mullet group. The reduced susceptible strains were observed the highest in 2014 and in Chiayi county and decreased from 2014 to 2016. However, the strains with reduced susceptibility to ceftriaxone, cirpofoxacin, moxifloxacin, tetracycline for human treatment were observed.

When a microgrid is grid-tied to a distribution system, it can provide surplus power generation to the distribution system, if any abnormality or interruption occurs in the distribution system, the microgrid can operate in standalone mode to isolate the impact of the abnormality or interruption. However, if the microgrid can not collect enough information from the distribution system, it may cause the failure of generation transferring of distribution feeders, or even further influence the stability of the distribution system. In this paper, a strategy for the resilient control of a microgrid is proposed. It can solve the above-mentioned problem, reduce the duration of the outage of loads. This strategy is experimented in the microgrid in the Institute of Nuclear Energy Research (INER), the reliability is also analyzed to evaluate the unavailability of the microgrid in INER, and it is verified that the proposed strategy can reduce the duration of the outage of loads, and hence the reliability of a microgrid can be upgraded.

We introduce two symmetric concepts to physics: “distance” (space and time in one) and “wavematter” (electromagnetic wave packet and matter in one). We claim that physics has chosen the wrong concept of time: It is not aware that the time of a moving object flows in a direction other than my time. We provide 15 proofs for our claim by solving 15 mysteries of physics graphically! For example, we prove that length contraction and time dilation are actually geometrical effects in a 4D manifold that we call “Euclidean spacetime” (ES). We prove that the discrepancy in calculating the Hubble constant stems from a systematic error in the redshift measurement. We prove that what I deem wave, deems itself matter, which solves wave–particle duality. We even untangle quantum entanglement without the issue of non-locality. We finally understand why alternative theories of Euclidean relativity have failed: They are all based on four dimensions of space rather than distance. A huge amount of energy was injected into ES at a point that we take as origin. Ever since has this energy been moving radially away at the speed of light. We live in the 3D hypersurface of an expanding 4D hypersphere. Hyperspherical coordinates have the great advantage that they reduce all that is ever happening to just one formula. So, it is the Theory of Everything in these coordinates: “Energy is covering radial distance which, divided by Euclidean time, is equal to the speed of light.” Acceleration and force like gravitation emerge from a rotation of objects in ES and a subsequent projection to 3D space. Matching the symmetry simplifies physics.

The targeting-Her-2/neu therapy by passive application with trastuzumab is associated with acquired resistance and subsequent metastasis development, attributed to upregulation of tumoral PD-L1 expression and downregulation of Her-2/neu. We aimed to investigate this association, following active immunization with our recently constructed B cell–peptide based Her-2/neu vaccines in both preclinical and clinical settings. Immunohistochemistry (IHC), fluorescence in situ hybridization (FISH), and combined positive score (CPS), were applied to evaluate Her-2/neu and PD-L1 expression using a murine syngeneic tumor model for Her-2/neu lung metastases, and tumor biopsies from a gastric cancer patient with disease progression. A significant and concomitant reduction of Her-2/neu and upregulation of PD-L1 expression was observed in the vaccinated mice, after 7 but not after 4 weeks of metastases development. A significant increase of tumor-infiltrating B lymphocytes was observed at both time points. Downregulation of Her-2/neu and upregulation of PD-L1 were observed in a patient’s primary tumor at the disease progression time point but not prior to vaccination (Her-2/neu IHC: 3 to 0, FISH: 4.98 to 1.63; PD-L1 CPS: 0% to 5%). Our results further underline the need for combination therapy by targeting PD-L1 to prevent metastasis formation and immune evasion of Her-2/neu positive and PD-L1 negative tumor cells.

High-strength low-alloy steels (HSLAs) are widely used in the structural body components of many domestic motor vehicles owing to their better mechanical properties and greater resistance. The real production process of HSLA steelmaking can be regarded as a model that builds on the relationship between process parameters and product quality attributes. A surrogate modeling method is used, and the resulting production process model can be applied to predict the optimal manufacturing process parameters. We used different methods in this paper to build such a surrogate model, including linear regression, random forests, support vector regression, multilayer perception, and a simplified VGG model. We then applied three bio-inspired search algorithms, namely particle swarm optimization, the artificial bee colony algorithm, and the firefly algorithm, to search for the optimal controllable manufacturing process parameters. Through experiments on 9,000 test samples used for building the surrogate model, and 299 test samples for making the optimal process parameter selection, we found that the combination of a simplified VGG model and the firefly algorithm was the most successful at reaching a success rate of 100%—in other words, when the product quality attributes of all test samples satisfy the mechanical requirements of the end products.

This paper investigates the hydroelastic responses of offshore floating solar photovoltaic farms (OFPVs) to minimize structural motion. The OFPV usually occupies a large sea space in the order of hectares and due to its huge structural length-to-thickness ratio, the structural deformation under wave action has to be taken into consideration. The flexible deformation of the structure under hydrodynamic loading is termed the hydroelastic response. Due to the relatively long structural length with respect to the encountering wavelength, the diffraction and radiation of waves have to be taken into account to accurately represent the hydrodynamic loadings on the floating platform. The numerical model is first validated by comparing the eigenvalues and eigenvectors of the OFPV obtained from the proposed numerical scheme with their counterparts obtained from an established finite element software. This is followed by the investigation of the hydroelastic response of various OFPVs designed in varying layout configurations. The various layout configurations are obtained by altering the floating modular units’ dimensions as well as the spacing of the OFPVs when deployed adjacent to each other. The optimal configuration that gives the best performance in terms of the overall smallest response, known as compliance, is then suggested. The results suggest that a longish OFPV layout has a lower hydroelastic response and the motion could be further reduced by increasing the global flexural stiffness via layout arrangement.

(1) Background: This study aimed to investigate the effect of increased HER-2 expression on tumor-infiltrating lymphocytes (TILs) and determine its impact on the prognosis of colorectal cancer (CRC) patients; (2) Methods: HER-2, CD4, CD8, CD19, LY6G, CD56, CD68, CD11b, and EpCam expression in CRC tissues and adjacent paracancerous tissues were assessed using multiplex fluorescence immunohistochemical staining. The correlation between HER-2 expression and the number of TILs in CRC tissues was analyzed. Kaplan-Meier and Cox proportional hazards models were used to analyze survival outcomes; (3) Results: The expression of HER-2 in tumor tissues was higher than that in paracancerous tissues (1.31 ± 0.45 vs. 0.86 ± 0.20, P < 0.05). Additionally, there was an increase in the numbers of CD4+, CD8+, CD19+, and CD68+ cells in CRC tissues (14.11 ± 1.10 vs. 3.40 ± 0.18, P < 0.005; 0.16 ± 0.12 vs. 0.04 ± 0.04, P < 0.005; 0.71 ± 0.46 vs. 0.25 ± 0.13, P < 0.0005; 0.27 ± 0.24 vs. 0.03 ± 0.11, P < 0.05). The increase in HER-2 expression was positively correlated with an increase in CD4, CD8, and CD19 (p < 0.0001). In HER-2-positive CRC tissues, CD68 expression was increased (0.80 ± 0.55 vs. 0.25 ± 0.22, P < 0.05). In HER-2-upregulated CRC tissues, CD4, CD8, CD19, CD68, CD11b, Ly6G, and CD56 expressions were elevated (0.70 ± 0.37 vs. 0.32 ± 0.17, P = 0.03; 0.22 ± 0.13 vs. 0.09 ± 0.06, P = 0.03; 0.31 ± 0.19 vs. 0.12 ± 0.08, P = 0.02; 1.05 ± 0.62 vs. 0.43 ± 0.21, P < 0.01; 1.34 ± 0.81 vs. 0.53 ± 0.23, P < 0.01; 0.50 ± 0.31 vs. 0.19 ± 0.10, P < 0.01; 1.26 ± 0.74 vs. 0.52 ± 0.24, P < 0.01). Furthermore, increased HER-2 expression is an independent risk factor for recurrence-free survival (RFS) in patients (P < 0.01, HR = 3.421); (4) Conclusions: The increased expression of HER-2 and its relationship with immune cells will provide new insights for immunotherapy in CRC patients.

Since sensor-based perception systems are used in autonomous vehicle applications, validating such systems is imperative to guarantee the robustness of the systems before they are being put to use. In this study, a comprehensive corruption-related simulation-based robustness verification and enhancement process for sensor-based perception systems is proposed. Firstly, we present a methodology and scenario-based corruption generation tools for creating diverse simulated test scenarios that can analogously represent real-world traffic environments, especially considering corruption types related to safety concern. Then, an effective corruption similarity filtering algorithm is proposed to remove corruption types with high similarity and identify the representative corruption types to represent all considered corruption types. As a result, we can generate efficient corruption-related robustness test scenarios with less testing time and good scenario coverage. Subsequently, we perform the vulnerability analysis of object detection models to identify model weaknesses and construct an effective training dataset for model vulnerability enhancement. This enhances the tolerance of object detection models to weather and noise-related corruptions, ultimately improving the robustness of the perception system. We employ case studies to demonstrate the feasibility and effectiveness of the proposed robustness verification and enhancement procedures. Additionally, we explore the impact of different "similarity overlap threshold" parameter settings on scenario coverage, effectiveness, scenario complexity (size of training and testing datasets), and time costs.

Based on the major, trace element, and isotope data of the Cenozoic basalts in the study area, it is indicated that the basalts in this region can be classified into three distinct magma systems: alka-li basalts, tholeiite basalts, and Nushan alkali basalts. The geochemical characteristics observed in the studied basalts indicate that the mantle source in this region might have experienced met-asomatic processes prior to partial melting, which could be linked to an ancient subduction pro-cess. Combining the geochemical characteristics in the studied basalts with previous research, we propose that the underlying mantle source in Anhui province may have undergone metaso-matism due to the carbonatitic melts. These melts are believed to have originated from car-bonated eclogite, derived from subducted Pacific slab materials present in the deeper mantle. According to the Sr-Nd isotope data, it is suggested that the mantle source in the Nushan region could be derived from a depleted asthenospheric mantle, while the basaltic composition in the Niugang area may be representative of the mantle's end components associated with the EM-I enriched mantle source present in this study area. Therefore, we propose that the Anhui basalts may have originated from the partial melting of a mantle source representing a mixing of two end-members: DMM (Depleted MORB Mantle) and EM-Ⅰ (Enriched Mantle 1). The Anhui basal-tic magmas may have originated from the partial melting of EM-Ⅰ, potentially influenced by upwelling asthenospheric mantle or asthenospheric diapirism processes. The mantle source in the study area experiences partial melting at 1-5%, 15%, and 1-10%, resulting in the formation of parent magmas for alkali basalt, tholeiitic basalt, and Nushan alkali basalt. Subsequently, the parent magmas experienced fractional crystallization processes, which included minerals like olivine, pyroxene, and plagioclase. This led to the formation of various types of basalt in the study area.

In this study we used a non-autonomous Chua’s Circuit, and the fractional Lorenz chaos system together with a detection method from Extension theory to analyze the voltage signals. The measured bearing signals by acceleration sensor were introduced into the master and slave systems through a Chua’s Circuit. In a chaotic system minor differences can cause significant changes that generate dynamic errors, and extension matter-element models can be used to judge the bearing conditions. Extension theory can be used to establish classical and sectional domains using the dynamic errors of the fault conditions. The results obtained were compared with those from Discrete Fourier Transform analysis, Wavelet analysis and an integer order chaos system. The diagnostic ratio showed the fractional order master and slave chaos system calculations. The results show that the method presented in this paper is very suitable for monitoring the operational state of ball bearing system to be superior to the other methods. The diagnosis ratio was better and there were other significant advantages such as low cost and few.

Concussion, also known as mild traumatic brain injury (mTBI), commonly causes transient neurocognitive symptoms, but in some cases, it causes cognitive impairment, including working memory (WM) deficit, which can be long-lasting and impede a patient’s return to work. The predictors of long-term cognitive outcomes following mTBI remain unclear because abnormality is often absent in structural imaging findings. The purpose of the study was to determine whether machine learning-based models using functional magnetic resonance imaging (fMRI) biomarkers and demographic or neuropsychological measures at baseline could effectively predict 1-year cognitive outcomes of concussion. We conducted a prospective, observational study of patients with mTBI who were compared with demographically-matched healthy controls enrolled between September 2015 to August 2020. Baseline assessments were collected within the first week of injury, and follow-ups were conducted at 6 weeks, 3 months, 6 months, and 1 year. Potential demographic, neuropsychological, and fMRI features were selected according to the significance of correlation with the estimated changes in WM ability. The support vector machine classifier was trained using these potential features and estimated changes in WM between the predefined time periods. Patients demonstrated significant cognitive recovery at the third month, followed by worsened performance after 6 months, which persisted until 1 year after concussion. Approximately half of the patients experienced prolonged cognitive impairment at 1-year follow up. Satisfactory predictions were achieved for patients whose WM function did not recover at 3 months (accuracy=87.5%), 6 months (accuracy=83.3%), 1 year (accuracy=83.3%), and performed worse at 1-year follow-up compared to baseline assessment (accuracy=83.3%). This study demonstrated the feasibility of personalized prediction for long-term postconcussive WM outcomes based on baseline fMRI and demographic features, opening a new avenue for early rehabilitation intervention in selected individuals with possible poor long-term cognitive outcomes.

Sweet pepper is an important vegetable in the world. Bacterial leaf spot caused by the pathogen Xanthomonas perforans, is a limiting factor that significantly reduces the quality and yield of sweet pepper To control this disease, the use of chemical fungicides is currently the main disease control method. Thus, we want to develop an alternative method by using antagonistic microorganisms. Under this demand, Bacillus amyloliquefaciens PMB04 has strong antagonistic effects against pathogens and can inhibit the occurrence of diseases. B. amyloliquefaciens PMB04 has the potential for the development of a disease control product. Primarily, PMB04 revealed to contain a strong inhibitory effect against all isolated X. perforans strains. In the inoculation assay, the severity of bacterial spot disease on sweet peppers was reduced by PMB04 bacterial suspensions. To increase the convenience of field application for future prospects, the development of PMB04 fermentation liquid was carried out with different ratios of brown sugar and yeast extract in a 30-liter fermentation tank subsequently. Results exhibited that the fermentation liquid of 3-1 formula obtained the highest bacterial population in a 30-liter fermentation tank. The fermentation liquid of 0.5-0.5 formula was the most stable formula under two different conditions in terms of consistent bacterial population and sporulation. In addition, the 200-fold dilution of 3-1 and 0.5-0.5 fermentation liquids revealed best control efficacy on bacterial leaf spot of sweet pepper. Additionally, the results of the 0.5-0.5 fermentation liquid (PMB4FL) with different dilution concentrations also showed that the 200- and 500-fold dilutions had the best control efficacy. To understand the effect of commonly used copper-containing fungicides on sweet peppers on the application of microbial agent PMB4FL, the effects of copper hydroxide and tribasic copper sulfate on the growth of X. perforans strains and B. amyloliquefaciens PMB04 were assayed. The results exhibited that the above two fungicides did not have any inhibitory effect on the growth of PMB04, but had a strong inhibitory effect on the X. perforans strain. In the follow-up control experiment, the treatment of copper hydroxide had no synergistic effect with PMB4FL to control bacterial leaf spot. We concluded that the use of PMB4FL fermentation liquid alone on the leaves can effectively control the occurrence of bacterial leaf spot in sweet pepper crops.

The hydrogen evolution reaction (HER) has garnered attention to access sustainable energy generation with a pollutant-free combustion product in the form of H2 gas. Despite the utility of this pathway in the context of growing climate concerns, stable HER electrocatalysts which avoid the use of rare-earth platinum while retaining high catalytic performance and efficiency remains a challenge. In this work, we present the application of a binuclear nickel (II/III) Schiff base complex [Ni]2[L]2 2 for HER electrocatalysis. The design of the electrocatalyst provides optimal HER activity as the presence of electronegative heteroatoms in proximity to the metal centers augments proton affinity. As a result, the catalyst displays excellent HER activity with 100% faradaic efficiency (FE) at an onset potential of 0.4 V vs. reverse hydrogen electrode (RHE), sustained catalytic activity during prolonged electrolysis for greater than 17 hours, and provided a turn over number (TON) of 0.0006 s-1.

This paper proposes an approach for image data extraction and driving behavior analysis using geographic information and driving data. Information derived from geographic and global positioning systems was used for image data extraction. In addition, we used an onboard diagnostic II and a controller area network bus logger to record driving data for driving behavior analysis. Driving behavior was analyzed using sparse automatic encoders and data exploration to detect abnormal and aggressive behavior. A regression analysis was used to derive the relationship between aggressive driving behavior and road facilities. Several traffic improvements were proposed for specific intersections and roads. The results indicate that lane ratios without lane markings and with straight lane markings are important features that affect aggressive driving behaviors.

High Efficiency Video Coding (HEVC) uses an 8-point filter and a 7-point filter, which are based on the discrete cosine transform (DCT), for the 1/2-pixel and 1/4-pixel interpolations, respectively. In this paper, discrete sine transform (DST)-based interpolation filters (IF) are proposed. The first proposed DST-based IFs (DST-IFs) use 8-point and 7-point filters for the 1/2-pixel and 1/4-pixel interpolations, respectively. The final proposed DST-IFs use 12-point and 11-point filters for the 1/2-pixel and 1/4-pixel interpolations, respectively. These DST-IF methods are proposed to improve the motion-compensated prediction in HEVC. The 8-point and 7-point DST-IF methods showed average BD-rate reductions of 0.7% and 0.3% in the random access (RA) and low delay B (LDB) configurations, respectively. The 12-point and 11-point DST-IF methods showed average BD-rate reductions of 1.4% and 1.2% in the RA and LDB configurations for the Luma component, respectively.

Aluminum alloy (Al6061) sheet micro-hole processing is extensively used in smartphones, tablet PC, and smart wearable devices. The micro-hole processing is commonly performed using laser, micro drilling, microstamping, micro discharge, and chemical etching technologies. Micro-stamping technology is characterized by precision and rapid processing, but the precision positioning of the punch head and lower die is one of the major difficulties in micro-hole stamping, especially in manufacturing array micro-holes. This study used stamping without die technology. This technology uses an array punch head to punch the lower die holes on the base, then performs array micro-hole stamping. The experimental results show that a micro-hole array with 37 micro-holes were successfully manufactured and can be reproduced many times. Tapered array micro-holes with a high aspect ratio can be manufactured using this stamping without die technology; the micro-hole depth can be 260μm, the inlet diameter is 116μm, and the outlet diameter is 25μm. This study has successfully developed the feasibility of array micro-hole stamping technology.

Corrosive burns lead to progressive esophageal stricture and dysphagia. There are many trials to prevent Esophageal stricture formation after corrosive burn. This study aimed to access the effects of EW-7197 on prevention for esophageal stricture formation after corrosive esophageal burn. animal study were classified divided into three groups: a healthy group, a control group (corrosive burn without EW-7197), and a treatment group (corrosive burn with EW-7197). Corrosive esophageal burns were produced using 30% NaOH on the lower esophagus. For 3 weeks, the control group received vehicle and the treatment group received 20 mg/kg/day EW-7197. Treatment efficacy was assessed by measuring the stenosis ratio by esophagogram with contrast media on day 21. histologic staining was performed to evaluate the fibrosis area ratio, and western blotting was performed to evaluate fibrotic markers. Among 20 rats that underwent surgery, 14 survived. Three in the treatment group died because of esophageal perforation, and three in the control group died due to their debilitating status. The esophageal stenosis ratio was significantly lower in the treatment group than in the control group (12.1 ± 9.5% and 42.2 ± 8.3%, respectively; p = 0.001). The histologic fibrosis area ratio was also significantly lower in the treatment group (12.5 ± 3.0% and 21.6 ± 2.1%, respectively; p = 0.001). The treatment group showed lower expressions of profibrogenic proteins such as TGF-β1, pSmad3, and α-SMA. EW-7197 may be a good alternative for the prevention esophageal stricture formation after corrosive burn.

In this paper we present the exploration of indoor positioning technologies for UAVs, and navigation techniques for path planning and obstacle avoidance. The objective is to perform warehouse inventory tasks using a drone to search for barcodes or markers to identify the objects. For the indoor positioning techniques, we employ Visual-Inertial Odometry (VIO), Ultra-Wideband (UWB), AprilTag fiducial markers, and Simultaneous Localization and Mapping (SLAM). These algorithms encompass global positioning, local positioning, and pre-mapping positioning, comparing the merits and drawbacks of various techniques and trajectories. In UAV navigation, we combine SLAM-based RTAB-Map indoor mapping and navigation path planning of the ROS for indoor environments. This system enables precise drone positioning indoors and utilizes global and local path planners to generate flight paths that avoid dynamic, static, unknown, and known obstacles, demonstrating high practicality and feasibility. To achieve the warehouse inventory inspection, a reinforcement learning approach is proposed to recognize the markers by adjusting the UAV's viewpoint. We address several main problems in inventory management, including efficiently planning paths while ensuring a certain level of detection rate. Two reinforcement learning techniques, AC (Actor-Critic) and PPO (Proximal Policy Optimization), are implemented based on AprilTag identification. Testing is performed in both simulated and real-world environments, and the effectiveness of the proposed method is validated.Code is available at https://github.com/kellen080/Navigation and https://github.com/kellen080/Indoor\_Positioning.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

Intelligent systems are increasingly present in various areas of society, gaining special relevance in healthcare environments. In this work, grounded on previous developments proposed by the authors, the evolution and improvement of a novel intelligent system focused on the diagnosis of obstructive sleep apnea (OSA) is addressed. To do this, starting from two packages of information of a heterogeneous nature, and deploying a set of Machine Learning classification algorithms, focused each of them on different levels of the apnea-hypopnea index (AHI), as well as a set of cascaded expert systems, it is possible to obtain a series of risk metric pairs (Statistical Risk, Symbolic Risk) for each AHI level, understood as a warning forecast associated with the early detection of the pathology. The risk indicators of each pair are subsequently aggregated by means of a symbolic inference system, whose knowledge base was determined using the automatic rule generation approach proposed by Wang and Mendel. At the output of each inference system, a risk indicator is obtained for each AHI level, the Apnea Risk, whose interpretation makes it possible to discriminate between patients who could suffer OSA and those who do not, as well as to generate the appropriate recommendations. For the initial tests of the system, the design and development of a specific software artifact was carried out using data from 4,400 patients from the Álvaro Cunqueiro Hospital in Vigo, obtaining when applied to the test set AUC values within the range 0.74–0.88, which invites optimism and points to the benefits expected from the architecture of the proposed intelligent system.

Plants of the genus Monochoria have long been utilized in food, cosmetics, and traditional herbal treatment. Thailand has the highest species diversity of this genus and a new member, Monochoria angustifolia (G. X. Wang) Boonkerd & Tungmunnithum has been recently described. This plant is called “Siam Violet Pearl” as a common name or “ไข่มุกสีม่วงแห่งสยาม” as its vernacular name in the same meaning in Thai language. Despite their importance, few researches on Monochoria species have been conducted. This study, thus, provided the results to fill in this gap by: i) determining flavonoids phytochemical profiles of 25 natural populations of M. angustifolia covering the whole floristic regions in Thailand, and ii) determining antioxidant activity using various antioxidant assays to investigate the probable mechanism. The results revealed that M. angustifolia presented a higher flavonoid content than the outgroup, M. hastata. Our results also revealed that flavonoids might be used to investigate Monochoria evolutionary connections and for botanical authentication. The various antioxidant assays revealed that M. angustifolia extracts preferentially act through a hydrogen atom transfer antioxidant mechanism. Pearson correlation analysis indicated significant correlations emphasizing that the antioxidant capacity is most probably the result of a complex phytochemical combinations rather than of a single molecule. Altogether, these results showed that this new species provide an attractive alternative starting material with phytochemical variety and antioxidant potential for the phytopharmaceutical industry.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

Red djulis (Chenopodium formosanum) is a native cereal plant in Taiwan; it contains abundant polyphenols, betalian and dietary fiber. The appearance of red djulis is bright red. Therefore, it is also called the “ruby of cereals”. The antioxidative activity of red djulis extract is well-understood. However, the antiaging function still remains unclear. This study examined the potential of red djulis extract for enhancing collagen secretion and preventing cutaneous aging using red djulis extracts. The red djulis extracts are comprised of an abundant active component that can effectively enhance the ability of collagen secretion of dermal fibroblasts, prevent the glycation of collagen and resist the damage of ultraviolet light exposure. After fibroblast treatment with red djulis extracts, TGM1, KRT1, KRT10 and SOD2 genes were up-regulated significantly by 2.3, 4.3, 4.4 and 27.3 times, respectively, compared to those of the control group. Additionally, it can increase COL1A2 gene expression by 43% and decrease MMP9 gene expression 33%. Therefore, it was demonstrated that red djulis extracts affect gene expressions related to the skin barrier, antioxidation and collagen. Moreover, we found positive effects on skin barrier integrity, endogenous antioxidant activity and skin collagen-preservation. The preparation of the red djulis extracts is environmental friendly and can promote the economic value of Chenopodium formosanum; thus, the proposed extract is suitable for applications in the development of food products, especially beverages, skin care and cosmetic products.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Carbapenemase-producing organisms (CPOs) present a major threat to public health, demanding precise diagnostic techniques their detection. Discrepancies among CPO tests have raised concerns, partly due to limitations in detecting bacterial diversity within host/specimen. We explored the impact of unbiased colony selection on carbapenemase testing and assessed its relevance on various tests. Based on "FirstAll" for unbiased colony selection to reduce bias, we compared modified carbapenem inactivation method/EDTA-modified carbapenem inactivation method (mCIM/eCIM), Carba5, the CPO panel, and multiplex PCR (M-PCR). Initially, we compared FirstAll to conventional colony selection for mCIM. Second, we used M-PCR as a reference, to evaluate test performance across seven CPO species. The results revealed that FirstAll selection improved carbapenemase detection, revising false-negative in 10.5% of K. pneumoniae isolates. In addition, 12.4% of CPOs tested positive for multiple carbapenemase genes. Both the Carba5 test and CPO panel showed suboptimal performance (sensitivity/specificity: Carba5 75.5%/89.0%, CPO panel 78.1%/74.0%). Carba5 test provided specific carbapenemase class assignments but CPO panel failed in 20.3% of cases. Carba5 test and the CPO panel results correlated well with ceftazidime-avibactam minimal inhibitory concentrations (MICs). Concordance for class A/D with MICs was 88.3% for Carba5 and 92.0% for the CPO panel; whereas for class B, it was 86.5% for Carba5 and 76.2% for the CPO panel. In conclusion, FirstAll as the unbiased colony selection impacted carbapenemase testing. With FirstAll, the diagnostic performance of either Carba5 or the CPO panel was compromised. The utilization of ceftazidime-avibactam guided by either the CPO panel or Carba5 was appropriate.

An oceanic radar altimeter such as TOPEX/Poseidon (T/P) is typically for observing elevation changes over the open oceans or large inland lakes/rivers, with limited applications over solid earth due to its large footprint and susceptibility to waveform contamination and slope effect. Here we demonstrate that it is possible to construct a long-term time series of glacier elevation change from T/P-series radar altimeters over two flat surfaces near a glacier terminus and an icefield (Sites A and B, with slopes of 2° and 0.8°) in Mt. Tanggula, Tibet, at elevations over 5400 m. We retracked radar waveforms using the subwaveform threshold algorithm, selected quality altimeter data (1/4 of the original) with nearly the same slope and adjusted the original elevations by fitting with a time-varying, 2nd order surface. The glacier elevation changes at the two sites from T/P (1993–2002) show seasonal elevation oscillations with linear rates at about −3 m/year and abnormal seasonal changes around the 1997–98 El Niño. Site A is over a deep valley in southern Tanggula. Its elevation dropped about 30 m over 1993–2002 (from T/P) and the glacier almost disappeared by 2016 (from altimeters and satellite images). Despite the sporadic Jason-2 and Jason-3 altimeter data, we also derived long-term rates of glacier elevation change over 1993–2017. Landsat-derived glacier area and elevation changes near the two sites confirm the rapid glacier thinning from the altimeters. The glacier meltwater near Site A supplied increasing source water to Chibuzhang Co west of Mt. Tanggula, contributing partially to its accelerated rising lake level. The glacier thinning at Site B (icefield) was correlated with the increased discharge of the Tuotuo River in eastern Mt. Tanggula, a source region of the Yangtze River. The successful detection of glacier thinning at the two sites shows that T/P-series altimeters can serve as a virtual station at a flat glacier spot to monitor long-term glacier elevation changes in connection to climate change. This virtual station concept is particularly useful for inaccessible glaciers, but its implementation faces two challenging issues: increasing the volume of quality altimeter data and improving the ranging accuracy over a targeted mountain glacier spot.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

Due to the rapid development and popularity of the Internet, cloud computing has become an indispensable application service. However, how to assign various tasks to the appropriate service nodes is an important issue. Based on the reason above, an efficient scheduling algorithm is necessary to enhance the performance of system. Therefore, a Three-Layer Cloud Dispatching (TLCD) architecture is proposed to enhance the performance of task scheduling. In first layer, the tasks need to be distinguished to different types by their characters. Subsequently, the Cluster Selection Algorithm is proposed to dispatch the task to appropriately service cluster in the secondly layer. Besides, a new scheduling algorithm is proposed to dispatch the task to a suitable server in a server cluster to improve the dispatching efficiency in the thirdly layer. Basically, the TLCD architecture can obtain better task completion time than previous works. Besides, our algorithm and can achieve load-balancing and reliability in cloud computing network.

In the last three decades the presence of phospholipids in the nucleus has been shown and thoroughly investigated. A great interest raised about nuclear inositol lipids mainly because of their role in signalling acting. Here we review the main issues of nuclear phospholipid localization and the role of nuclear inositol lipids and their related enzymes in cellular signaling both in physiological and pathological conditions.

In this study, the resource blocks (RB) are allocated to user equipment (UE) according to the evolutional algorithms for long term evolution (LTE) systems. Particle Swarm Optimization (PSO) algorithm is one of the evolutionary algorithms, based on the imitation of a flock of birds foraging behavior through learning and grouping the best experience. In previous work, the Simple Particle Swarm Optimization (SPSO) algorithm was proposed for RB allocation to enhance the throughput of Device-to-Device (D2D) communications and improve the system capacity performance. In simulation results, with less population size of M = 10, the SPSO can perform quickly convergence to sub-optimal solution in the 100^th generation and obtained sub-optimum performance with more 2 UEs than the Rand method. Genetic algorithm (GA) is one of the evolutionary algorithms, based on Darwinian models of natural selection and evolution. Therefore, we further proposed a Refined PSO (RPSO) and a novel GA to enhance the throughput of UEs and to improve the system capacity performance. Simulation results show that the proposed GA with 100 populations, in 200 generations can converge to suboptimal solutions. Therefore, with comparing with the SPSO algorithm the proposed GA and RPSO can improve system capacity performance with 1.8 and 0.4 UEs, respectively.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

The requirements for efficient replacement of fossil fuel, combined with the growing energy crisis, put hydrogen production into focus. Efficient and cost-effective electrocatalysts are needed for H2 production, and novel strategies for their discovery must be developed. Here we utilized Kinetic Monte Carlo (KMC) simulations to demonstrate that hydrogen evolution reaction (HER) can be boosted via hydrogen spillover to the support when the catalyst surface is largely covered by adsorbed hydrogen under operating conditions. Based on the insights from KMC, we synthesized a series of reduced graphene oxide-supported catalysts and compared their activities towards HER in alkaline media with that of corresponding pure metals. For Ag, Au, and Zn, the support effect is negative, but for Pt, Pd, Fe, Co, and Ni, the presence of the support enhances HER activity. The HER volcano, constructed using calculated hydrogen binding energies and measured HER activities, shows a positive shift of the strong binding branch. This work demonstrates the possibilities of metal|support interface engineering for producing effective HER catalysts and provides general guidelines for choosing novel catalyst-support combinations for electrocatalytic hydrogen production.

Background. Recent studies revealed that differentiation of valvular interstitial cell into myofibroblasts played an important role in pathological valve remodeling in rheumatic valvular disease. Objective. To investigate effects of atorvastatin, olmesartan, and resveratrol on Transforming Growth Factor β1-induced fibrosis. Methods. Valvular interstitial cell was isolated from 12-weeks male New Zealand rabbit (Oryctolagus cuniculus). Culture cells was divided into 4 groups, control group, group I (0.5 mg/mL Atorvastatin), group II (100 nmol/L Olmesartan), group III (50 μM/L Resveratrol) and group IV (combinations). All group were exposed to 100 nM Transforming Growth Factor β1 for 24 hours. Results. Immunochemical staining demonstrated that cells were completely differentiated into myofibroblasts with mean expression of α-smooth muscle actin 24522.64±4566.994. Atorvastatin, olmesartan, resveratrol, and its combination significantly reduced α-smooth muscle actin expression (6823±1735.3, 6942.7±2455.9, 14176.2±3343.3, 5051.8±1612.2 respectively (p&lt;0.001). Conclusion. Our data showed atorvastatin, olmesartan, resveratrol, and its combination significantly reduce Transforming Growth Factor β1-induced valvular fibrosis.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

The anti-inflammatory effect of ginsenoside Rh2 (GRh2) is one of the most important ginsenosides. The purpose of this study is to identify the anti-inflammatory and antioxidant effects of GRh2 after LPS challenge lung injury animal model. GRh2 reduced LPS-induced NO, TNF-α, IL-1, IL-4, IL-6 and IL-10 productions in lung tissues. GRh2 treatment decreased the histological alterations in the lung tissues and BALF protein content and total cells number also diminished in LPS-induced lung injury mice. Moreover, GRh2 blocked iNOS, COX-2, the phosphorylation of IκB-α, ERK, JNK, p38, Raf-1 and MEK protein expression which is corresponded to the growth of HO-1, Nrf-2, catalase, SOD and GPx expressions in LPS-induce lung injury. An experimental study has suggested that GRh2 has provided with anti-inflammatory effects in vivo, and its potential therapeutic efficacy in major anterior segment lung diseases.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Background: Idiopathic pulmonary fibrosis (IPF) is a progressive fibrotic lung disease with a poor prognosis. Pirfenidone is approved and widely used for the treatment of IPF and reduces lung function decline. The aim of this study was to evaluate the efficacy of different doses of pirfenidone for the prevention of disease progression in patients with IPF. Methods: This was a prospective, observational, single-center cohort study conducted in Haeundae Paik Hospital, Republic of Korea, from April 2021 to March 2023. IPF patients were assigned to three groups according to the dose of pirfenidone (600mg, 1,200mg, 1,800mg). The primary endpoint was the efficacy of pirfenidone according to dose for the prevention of disease progression over 12 months. The secondary endpoint was the role of Krebs von den Lungen-6 (KL-6) in predicting disease progression. Results: A total of 44 patients were enrolled, of whom 39 completed the study, with 13 patients assigned to each of the three groups. The median age was 71.7 years, and 79.5% of patients were men. The baseline characteristics were similar across groups, except the 600mg group was older (75.9 vs. 69.2 vs. 68.2 years, p = 0.016). Fourteen patients (35.9%) suffered disease progression. The rate of disease progression did not differ according to the dose of pirfenidone (38.5 vs. 38.5 vs. 30.8%, p = 1.000). In multivariable logistic regression analysis, KL-6 was not a statistically significant predictor of disease progression. Conclusions: In our study, regardless of dose, consistent pirfenidone use for 12 months resulted in similar efficacy for the prevention of disease progression in patients with IPF. Large-scale, randomized, double-blind, placebo-controlled clinical trials are needed.

Introduction. Recent studies revealed that differentiation of valvular interstitial cell into myofibroblasts played an important role in pathological valve remodeling in rheumatic valvular disease. Objective. To investigate effects of atorvastatin, olmesartan, and resveratrol on Transforming Growth Factor β1-induced fibrosis. Methods. Valvular interstitial cell was isolated from 12-weeks male New Zealand rabbit (Oryctolagus cuniculus). Culture cells was divided into 4 groups, control group, group I (0.5 mg/mL Atorvastatin), group II (100 nmol/L Olmesartan), group III (50 μM/L Resveratrol) and group IV (combinations). All group were exposed to 100 nM Transforming Growth Factor β1 for 24 hours. Results. Immunochemical staining demonstrated that cells were completely differentiated into myofibroblasts with mean expression of α-smooth muscle actin 24522.64±4566.994. Atorvastatin, olmesartan, resveratrol, and its combination significantly reduced α-smooth muscle actin expression (6823±1735.3, 6942.7±2455.9, 14176.2±3343.3, 5051.8±1612.2 respectively (p<0.001). Conclusion. Our data showed atorvastatin, olmesartan, resveratrol, and its combination significantly reduce Transforming Growth Factor β1-induced valvular fibrosis.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Importance: Because of the high prevalence of myopia in Taiwan, understanding the risk factors for its development and progression is important to public health. Background: This study investigated the risk factors for myopia and their influence on the progression of myopia in schoolchildren in Taiwan. Design: Patients’ clinical records were obtained retrospectively from ophthalmologists. Questionnaires were given to collect demographic information, family background, hours spent on daily activities, myopia progression, and treatment methods. Participants: A total of 522 schoolchildren with myopia from a regional medical hospital in northern Taiwan participated the study. Written informed consent was obtained from the participants of legal age or the parents or legal guardians. Methods: Multivariable regression analyses were performed. Myopia measured in dioptres was analysed, controlling for patients’ family and demographic information as well as their daily behaviours. Main Outcome Results: Children with high myopic parents were more myopic. Earlier onset age of myopia was associated with a higher level of myopia and greater annual myopic progression. Children reporting more near work activities had higher levels of myopia and greater progression of myopia. Lower levels of myopia were associated with more exercise, longer periods of sleep, and better vision care knowledge in children and parents. Intake of food supplements had no effect on myopia. Conclusions and Relevance: In addition to genetics, education, environment, and near work activity can influence the development of myopia. Health policies for schoolchildren should promote protective activities and vision care knowledge in order to protect the eyesight of schoolchildren.

Ischemic neuron loss contributes to brain dysfunction in patients with cardiac arrest (CA). Histidine–tryptophan–ketoglutarate (HTK) solution is a preservative used during organ transplantation. Can HTK also protect neurons from severe hypoxia (SH) following CA? We isolated rat primary cortical neurons and induced SH with or without HTK. Changes in caspase-3, hypoxia-inducible factor 1-alpha (HIF-1α), and NADPH oxidase-4 (NOX4) expression were evaluated at different time points till 72 h. Using a rat asphyxia model, we induced CA-mediated brain damage and then completed resuscitation. HTK or sterile saline was administered into the left carotid artery. Neurological deficit scoring and mortality were evaluated for 3 days. Then the rats were sacrificed for evaluating NOX4 and H2O2 level in blood and brain. In the in vitro study, HTK attenuated SH- and H2O2-mediated cytotoxicity in a volume- and time-dependent manner, associated with persisted HIF-1α expression, reductions in procaspase-3 activation and NOX4 expression. The inhibition of HIF-1α abrogated HTK’s effect on NOX4. In the in vivo study, neurological scores were significantly improved by HTK. H2O2 level, NOX4 activity and NOX4 gene expression were all decreased in the brain specimen of HTK-treated rats. Our results suggest that HTK acts as an effective neuroprotective solution.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

The nuclear factor-ĸB (NF-ĸB) transcriptional system is a major effector pathway involved in inflammatory responses. Previous studies found that a Gardenia decoction (GD) inhibited the expression of NF-κB in a lipopolysaccharide (LPS)-stimulated mouse intestinal injury model. Herein, we hypothesized that geniposide (GE), a component of Gardenia jasminoides Ellis, also exerts anti-inflammatory effects and inhibits NF-ĸB activity in LPS-induced intestinal epithelial cells (IEC-6). IEC-6 cells were stimulated with LPS, following which the effects of GE on NF-ĸB signaling in the IEC-6 cells were examined by western blotting to detect IĸB phosphorylation/degradation. The expression of NF-κB was determined by immunofluorescence assay (IFA). Enzyme-linked immunosorbent assay (ELISA) was used to detect the inhibitory effect of GE on the release of tumor necrosis factor-α (TNF-α), interleukin-6 (IL-6) and interleukin-1β (IL-1β) activated by LPS in IEC-6 cells. In addition, the migration ability of IEC-6 cells was observed by the scratch method. These results showed that GE dose-dependently downregulated levels of the proinflammatory cytokines TNF-α, IL-6 and IL-1β that had been upregulated by LPS and suppressed the phosphorylation of IĸB and NF-ĸB induced by LPS. Our findings indicated that GE could reduce LPS-induced NF-ĸB signaling and proinflammatory expression in IEC-6 cells and significantly enhance the migration of IEC-6 cells. Moreover, GE inhibited the expression of NF-κB, nuclear transfer, and transcriptional activity in IEC-6 cells. GE could block the synthesis of inflammatory factors of IEC-6 cells by inhibiting activation of the IĸB/NF-κB signaling pathway induced by LPS.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Background: This retrospective study evaluates the survival effects of metronomic maintenance therapy with fluoropyrimidine in patients with stage III colorectal cancer (CRC) according to epidermal growth factor receptor (EGFR) expression. Methods: We enrolled 197 patients with stage III CRC who had undergone radical resection and FOLFOX regimen adjuvant chemotherapy. The clinicopathological features and effects of metronomic maintenance therapy on survival according to treatment group and EGFR expression were analyzed. By conducting an in vitro cell line study and in vivo study through knockdout of EGFR gene, we analyzed the capacities of cell proliferation and migration. Results: Postoperative relapse and mortality were significantly more common in the FOLFOX group. Metronomic maintenance therapy was a significantly independent predictive factor of postoperative relapse and mortality, as well as a prognostic factor of disease-free survival and overall survival. The significant differences of survival between the two groups were only observed in patients with positive EGFR expression. Conclusions: The present study suggested EGFR expression as the prognostic factor in patients with stage III CRC receiving metronomic maintenance therapy. By analyzing EGFR expression, we can identify the potential candidates with optimal survival benefit from metronomic maintenance therapy in patients with stage III CRC.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

The increased consumption of high fat-containing foods has been linked to the prevalence of obesity and abnormal metabolic syndromes. Rhizopus oligosporus, a fungus in the family Mucoraceae, is widely used as a starter for homemade tempeh. Although R. oligosporus can prevent the growth of other microorganisms, it grows well with lactic acid bacteria (LAB). Lactobacillus plantarum can produce β-glucosidase, which catalyzes the hydrolysis of glucoside isoflavones into aglycones (with greater bioavailability). Therefore, the development of a soybean-based functional food by the co-inoculation of R. oligosporus and L. plantarum is a promising approach to increase the bioactivity of tempeh. In this study, the ameliorative effect of L. plantarum in soy tempeh on abnormal carbohydrate metabolism in high-fat diet (HFD)-induced hyperglycemic rats was evaluated. The co-incubation of L. plantarum with R. oligosporus during soy tempeh fermentation reduced the homeostatic model assessment of insulin resistance, HbA1c, serum glucose, total cholesterol, triglyceride, free fatty acid, insulin, and low-density lipoprotein contents and significantly increased the high-density lipoprotein content in HFD rats. It also increased the LAB counts as well as the bile acid, cholesterol, triglyceride, and short-chain fatty acid contents in the feces of HFD rats. Our results suggested that the modulation of serum glucose and lipid levels by LAB occurs via alterations in the internal microbiota, leading to the inhibition of cholesterol synthesis and promotion of lipolysis. Tempeh, produced with both L. plantarum and R. oligosporus, may be a beneficial dietary supplement for individuals with abnormal carbohydrate metabolism.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

This study aims to develop an elderly care system for improving the interpersonal relationship of the elderly with mild cognitive impairment (MCI) by employing the speaker recognition technique and association functionality of social network platforms. Firstly, the speaker recognition units based on the Gaussian Mixture Model (GMM) and Gaussian Mixture Model-Universal Background Model (GMM-UBM) are implemented to identify the visitor via individual input utterance. After the visitor is identified, the proposed system will be linked to the private database and social network platforms to extract the associated message of two parties. Experimental results indicate that the speaker recognition unit based on GMM-UBM achieves the best performance. Finally, five elderly persons are invited to measure the usability of the proposed system. A questionnaire is used to survey the five elderly persons, and the result indicates that the proposed system is highly potentially applicable in improving the interpersonal relationship of the elderly with MCI.

This study aimed to use biomineralization technology to improve the bond strength of fiber-reinforced lightweight aggregate concrete (LWAC) after exposure to temperatures of 300 °C and 500 °C. The specimens of a control group (Group A) and two experimental groups (Group B and Group C) were prepared. These specimens healed themselves in different ways after exposure to high temperatures and pull-out tests. The self-healing method of Group A involved placing the specimen into an incubator. The self-healing method of Group B was the same as that of Group A. The self-healing method of Group C involved immersing the specimen in a mixed solution of urea and calcium acetate for two days, then taking it out and placing it in an incubator for two days. A cycle of four days was undertaken until the desired age was reached. After the specimens were healed to the planned age, the first and secondary pull-out tests and repair compound identification were carried out. After exposure to a temperature of 300 °C and self-healing for 90 days, compared with the specimens in Group A, the relative bond strength ratios of the secondary pull-out tests of the specimens in Group C increased by 20.3%. This indicates that biomineralization can effectively improve the bond strength of LWAC after high-temperature damage.

Due to the recent trend of unmanned economy, retail stores have gradually reduced their service and cashier manpower. The retail product recognition becomes one of key issues for unmanned shopping. Although the success of deep neural networks has made object recognition feasible in a variety of applications, it still struggles to perform well on a large number of classes of retail products. In this paper, we propose an improved ensemble learning-based approach for retail product recognition. In the proposed approach, the object classification network is first improved through feature extraction and block attention. An ensemble model is then built by integrating multiple network models and using loss selection as model weights. In the experiments, the feasibility of our ensemble learning-based approach has been evaluated through many production items. The results demonstrate the effectiveness of the proposed approach compared with previous retail product recognition methods.

Bone Scan Index (BSI) is an image biomarker for quantification on bone metastasis of cancers. To compute BSI, not only the hotspots (metastasis) but also the bones have to be segmented. Most related researches focus on binary classification on bone scintigraphy: having metastasis or none. Rare studies focus on pixelwise segmentation. In this study we compare three advanced convolutional neural network (CNN) based models to explore the bone segmentation on dataset in house. The best model is Mask R-CNN, which reaches the precision, sensitivity and F1-score: 0.93, 0.87, 0.90 for prostate cancer patients and 0.92, 0.86, 0.88 for breast cancer patients, respectively. The results are the average of 10-fold cross-validation, which reveals the reliability for clinical use on bone segmentation.

Background and Aims: Of all primary liver tumors, primary hepatic angiosarcoma (PHA) is a rare and aggressive malignant vascular tumor. The standard therapeutic care for hepatic angiosarcoma remains unclear. This study compared the survival outcomes of aggressive treatment (resection and liver transplant) and nonaggressive treatment (chemotherapy, transarterial chemoembolization [TACE], and conservative treatments) for patients with PHA and analyzed the prognostic factors influencing survival. Materials and Methods: Data of patients diagnosed as having PHA at our facility were retrospectively reviewed. The primary outcome was survival time. The secondary outcome was calculated baseline characteristics. Results: We included a total of 19 patients, who were divided into 2 treatment groups: aggressive (8 patients had undergone resection or transplants) and nonaggressive (11 patients had undergone TACE, chemotherapy, or conservative treatment). The mean survival time was 233.1 ± 189.7 days in the aggressive treatment group and 146.5 ± 115.8 days in the nonaggressive treatment group. A Kaplan-Meier plot revealed no significant difference in survival time between the 2 treatment groups (P = .3256). Conclusions: The survival time of patients receiving aggressive treatment was longer than that of those receiving nonaggressive treatment. The long term survival time in some selective cases of aggressive treatment will be achieved. Thought a difference was not significant between the groups. Because the number of patients was limited, more cases are required to confirm these findings.

Hyperuricemia (HC) was one of the important risk factors for gout, arteriosclerosis, and cardiovascular disease. Animal studies have shown that Lactobacillus plantarum can improve the microbiota, immune regulation, and inhibit the uric acid production. However, it was not clear whether L. plantarum can improve HC and intestinal microbiota. We used potassium oxonate (PO) to induce HC in male SD rats, and then treated L. plantarum TCI227 in a dose dependent (HC+LD, HC+MD, HC+HD) for 4 weeks, and examined weight organs, biochemical examination of blood and urine, and analyzed the intestinal microbiota in feces by 16s rDNA sequence analysis. In this study, TCI227 improved body weight, decreased creatinine, serum uric acid, and increased urine uric acid compared to the HC group. Furthermore, TCI227 increased short-chain fatty acids (SCFAs). In fecal microbiota (family), TCI227 increased the level of Lactobacillaceae, and then decreased the level of Deferribacteres and Prevotellaceae compared to the HC group. Finally, in fecal microbiota (genus), TCI227 decreased the level of Prevotella, and then increased the level of Lactobacillus and Ruminococcus compared to the HC group. This study suggested that TCI227 can improve HC and change the compositions of the intestinal microbiota in PO induced male HC SD rats.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

When an aircraft malfunctions, quickly and accurately identifying the faulty unit is essential for ensuring normal operation. Unfortunately, maintenance engineers often struggle to acquire the necessary fault-related knowledge due to poor management and utilization of aircraft fault documents. To address this issue, we introduce knowledge graph technology into the field of aircraft fault diagnosis, exploring its construction and application for effective knowledge management. Our work starts by analyzing the critical knowledge elements required for aircraft fault diagnosis and designing a schema layer for fault knowledge graphs. We then we then combine deep learning and heuristic rules to extract fault knowledge from both structured and unstructured data, enabling the construction of aircraft fault knowledge graphs. Finally, we develop a fault question-answering system based on fault knowledge graphs that can accurately give solutions to questions posed by maintenance engineers. Our practice demonstrates that knowledge graphs provide an effective means of managing aircraft fault knowledge, assisting engineers in locating fault reasons accurately and quickly.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

The association between normal-range triglycerides and diabetes mortality remains unclear. This cohort study aimed to elucidate this relationship by examining 19,010 US adult participants with fasting serum triglycerides below 150 mg/dL. Cox proportional hazards models were employed to estimate mortality hazard ratios (HRs) and 95% confidence intervals (CIs). Participants were followed up for a mean of 15.3 years, during which 342 diabetes deaths were recorded. A 1-natural-log-unit increase in triglycerides was associated with a 57% higher risk of diabetes mortality (adjusted HR, 1.57; 95% CI, 1.04–2.38). Comparable results were obtained when triglycerides were analyzed in quartiles. Receiver operating characteristic curve analysis identified an optimal triglyceride cutoff of 94.5 mg/dL for diabetes mortality; individuals with triglyceride levels above this threshold faced a greater risk of diabetes mortality (adjusted HR, 1.43; 95% CI, 1.12–1.83). Further investigation revealed a positive association between normal triglyceride levels and all-cause mortality, though no association was observed between normal triglycerides and mortality from hypertension or cardiovascular disease. In conclusion, elevated triglycerides within the normal range were associated with an increased risk of diabetes mortality. Individuals with triglyceride levels of 95 mg/dL or higher may require vigilant monitoring for diabetes and its associated complications.

Upper mesophilic temperature acclimation of halophilic, hydrogen-producing bacteria from salt fields was investigated in this study, along with the changes in microbial abundance during an-aerobic digestion (AD) process. Genomic approaches such as PCR-denaturing gradient gel elec-trophoresis (DGGE) and next-generation sequencing (NGS) were performed to profile the mi-crobial communities. During AD, there was a significant abundance of Halanaerobacter lacunarum at 48°C followed by the increase in hydrogen yield, signifying potential contribution from the halophile in the hydrogen production. A decrease in the dominance of H. lacunarum and Halan-aerobium fermentans at 42°C, likely due to an increase in other bacterial species, was noted but their dominance significantly increased at temperatures of 45°C and 48°C. This investigation provides valuable insights in highlighting the potential of Halanaerobium sp. and the other halo-philic bacteria to adapt under upper mesophilic temperature conditions and synthesizing hy-drogen. The findings in the present study also underscore the importance of optimizing temper-ature and pH conditions to maximize hydrogen yield during high-salt anaerobic digestion.

This purpose of the study presented in this article is to comparing different service quality measurements between Kano and TRIZ that plays the critical roles in the catering industrial. Data collected from a DINESERV questionnaire comprises service-quality standards to increase customer satisfaction of mobile dining car. Finally, the TRIZ is standardized measure designed to improve the idealization of strategy for selecting the most appropriate service quality model. In addition, the preferences of more than one decision maker are internally aggregated into the TOPSIS procedure. All these things provide several important theoretical and practical implications for developing a successful mobile catering app.

Malignant cells cultured in three-dimensional (3D) models have been found to be phenotypically and biochemically different from their counterparts cultured conventionally. Since most of these studies employed solid tumor types, how 3D culture affects multiple myeloma (MM) cells is not well understood. Here, we compared MM cells (U266 and RPMI8226) in a 3D culture model with those in conventional culture. While the conventionally cultured cells were present in single cells or small clusters, MM-3D cells grew in large spheroids. We discovered that STAT3 was the pathway that was more activated in 3D in both cell lines. The active form of STAT3 (phospho-STAT3 or pSTAT3), which was absent in MM cells cultured conventionally, became detectable after 1-2 days in 3D culture. This elevated pSTAT3 level was dependent on the 3D environment, since it disappeared after transferring to conventional culture. STAT3 inhibition using a pharmacological agent, Stattic, significantly decreased the cell viability of MM cells and sensitized them to bortezomib in 3D culture. Using an oligonucleotide array, we found that 3D culture significantly increased the expression of several known STAT3 downstream genes implicated in oncogenesis. Since most primary MM tumors are naturally STAT3-active, studies of MM in 3D culture can generate results that are more representative of the disease.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

The Yixian Formation (Lower Cretaceous) of China is famous worldwide for its fossils of early angio-sperms, but there is only one record of flower bud hitherto. A previous fossil record of flower bud just showed the appearance and lacked any internal details. Such a lacuna in knowledge of flower buds hin-ders our understanding of the evolution of flowers. Our new specimen was collected from an outcrop of the Yixian Formation (the Barremian-Aptian, Lower Cretaceous) near Dawangzhangzi, Lingyuan, Liao-ning, China. The specimen was observed and photographed using a Sony ILCE-7 digital camera and a Nikon SMZ1500 stereomicroscope, and details were observed using a TESCAN MAIA3 SEM. Our ob-servations document a fossil flower bud, Archaebuda cretaca sp. nov, from the Lower Cretaceous of China. The occurrence of two species of Archaebuda in the Yixian Formation not only confirms the ex-istence of the expected gynoecium (and possible androecium) in a flower bud, but also underscores the occurrence of typical flowers in the Early Cretaceous.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

The foot-mounted inertial navigation system is an important application of pedestrian navigation as it in principle does not rely any external assistance. A real-time range decomposition constraint method is proposed in this paper to combine the information of dual foot-mounted inertial navigation systems. It is well known that low-cost inertial sensors with ZUPT (zero-velocity update) and range decomposition constraint perform better than in either single way. This paper recommends that the distance of separation between the position estimates of feet-mounted inertial navigation systems be restricted in the ellipsoidal constraint which relates to the maximum step and leg height. The performance of the proposed method is studied utilizing experimental data. The results indicate that the method can effectively correct the dual navigation systems’ position over the existing spherical constraint.

Open-vocabulary learning has recently gained prominence as a means to enable image segmentation for arbitrary categories based on textual descriptions. This advancement has extended the applicability of segmentation systems to a broader range of generally purpose scenarios. However, current methods often revolve around specialized architectures and parameters tailored to specific segmentation tasks, resulting in a fragmented landscape of segmentation models. In response to these challenges, we introduce OVAMTSeg, a versatile framework designed for Open-Vocabulary and Multitask Image Segmentation. OVAMTSeg harnesses adaptive prompt learning to empower the model to capture category-sensitive concepts, enhancing its robustness across diverse multi-task and scenario contexts. Text prompts are employed to effectively capture semantic and contextual features of the text, while cross-attention and cross-modal interactions enable the fusion of image and text features. Furthermore, a transformer-based decoder is incorporated for dense prediction. Extensive experimental results underscore the effectiveness of OVAMTSeg, showcasing its state-of-the-art performance and superior generalization capabilities across three segmentation tasks. Notable achievements include a 47.5 mIoU in referring expression segmentation, 51.6 mIoU on Pascal-VOC with four unseen classes, 46.6 mIoU on Pascal-Context in zero-shot segmentation, 65.9 mIoU on Pascal-5i, and 35.7 mIoU on COCO-20i datasets for one-shot segmentation.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

There is limited evidence for the association between malnutrition and hospital mortality as well as Intensive Care Unit length-of-stay (ICU-LOS) in critically ill patients. We aimed to examine the aforementioned associations by conducting a prospective cohort study in an ICU of a Singapore tertiary hospital. Between August 2015 and October 2016, all adult patients with ≥24 h of ICU-LOS were included. The 7-point Subjective Global Assessment (7-point SGA) was used to determine patients’ nutritional status within 48 hours of ICU admission. Multivariate analyses were conducted in two ways: 1) presence versus absence of malnutrition, and 2) dose-dependent association for each 1-point decrease in the 7-point SGA. There were 439 patients of which 28.0% were malnourished, and 29.6% died before hospital discharge. Malnutrition was associated with an increased risk of hospital mortality [adjusted-RR 1.39 (95%CI: 1.10–1.76)], and this risk increased with a greater degree of malnutrition [adjusted-RR 1.09 (95%CI: 1.01–1.18) for each 1-point decrease in the 7-point SGA]. No significant association was found between malnutrition and ICU-LOS. Conclusion: There was a clear association between malnutrition and higher hospital mortality in critically ill patients. The association between malnutrition and ICU-LOS could not be replicated and hence requires further evaluation.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

Observe the synergistic effect and dose-effect relationship of Trimethoprim (TMP) on bactericidal activity with Flos Lonicerae in vitro. Microamount chessboard dilution method was conducted to determine the minimal inhibitory concentration (MIC) of Trimethoprim, Flos Lonicerae, as well as the combination of Trimethoprim and Flos Lonicerae separately against Staphylococcus aureus, Escherichia coli in vitro and Salmonella. The pour plate count method was used to determine the combined bactericidal activity of Flos Lonicerae combined with Different concentrations TMP. The results showed that the MIC values of the combination of Flos Lonicerae with TMP was much less than the MIC values of the independent use of Flos Lonicerae or TMP, The FIC values of the combination of Flos Lonicerae with TMP were between 0.5 and 1, there was additive effect between them. The bactericidal rates were fitted with least square method, the 95% confidence intervals of the optimal blending quantity about the combination of Flos Lonicerae with TMP on the test organisms were 231μg·mL^-1-249μg·mL^-1, 237μg·mL^-1-259μg·mL^-1, and 235 -259μg·mL^-1

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

This work focuses on addressing the dynamic positioning and trajectory tracking problem for a 4 degree-of-freedom (DOF) unmanned underwater vehicle (UUV) in the presence of nonlinear dynamics, parametric uncertainties, system constraints, and time-varying external disturbances. To tackle this problem, a disturbance observer-based control (DOBC) scheme is proposed. The scheme is structured around the model predictive control (MPC) method integrated with an extended active observer (EAOB). Compared to the conventional disturbance observer, the EAOB has the unique ability to handle both external disturbances and system/measurement noises simultaneously. The EAOB leverages a combination of sensor measurements and a system dynamic model to estimate disturbances in real-time, which allows continuous estimation and compensation of time-varying disturbances back to the controller. The proposed disturbance observer-based MPC (DOBMPC) is implemented by feeding the estimated disturbances back into the MPC’s prediction model, which forms a robust adaptive controller with a parameter-varying model. The proposed control strategy is validated through simulations in a Gazebo and Robot Operating System (ROS) environment. The results show that it can effectively reject unpredictable disturbances and improve the UUV’s control performance.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P &lt; 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P &lt; 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P &lt; 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.