A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

As symbionts of fungi and algae, lichens produce a variety of secondary products which pharmacological activities. This study aimed to investigate the anti-inflammatory activities of Heterodermia hypoleuca and its main compound, atraric acid. The results confirmed that atraric acid could regulating induced pro-inflammatory cytokine, nitric oxide, induced nitric oxide synthase and cyclooxygenase-2 expression by lipopolysaccharide (LPS)-stimulated RAW264.7 cells. Means while, atraric acid down-regulated expression of phosphorylated IκB, ERK and nuclear factor kappa B (NFκB) signaling pathway to exhibit anti-inflammatory effects in LPS-stimulated RAW264.7 cells. Based on these results, the anti-inflammatory effect of atraric acid during LPS-induced endotoxin shock in a mouse model was confirmed. In the atraric acid treated-group, cytokine production was decreased in the peritoneum and serum, and each organ damaged by LPS-stimulation was recovered. These results show that atraric acid has an anti-inflammatory effect and its molecular mechanism may be involved in the inactivation of the ERK/NFκB signaling pathway, demonstrating its value as a potential therapeutic for inflammatory diseases.

In this study, the literature on varnish contamination is investigated among the various con-taminations of lubricant. As the period of use of lubricant increases, the lubricant deteriorates and becomes contaminated. The varnish causes filter plugging, sticking of hydraulic valves and fuel injection pumps, obstruction of flow, reduction of clearance, poor heater and cooler perfor-mance, and increase of friction and wear in various lubrication systems. These problems also cause mechanical system failure, performance degradation, and increased maintenance and re-pair cost. To improve the problems causes by the varnish, an adequate understanding of varnish is required. Therefore, in this literature review, definitions and characteristics, generating ma-chinery, generating mechanisms, causes, measurement methods, and prevention or removal methods are summarized. Most of the data are reports of companies related to lubricant and machine maintenance, and are included in some papers. We hope that this summary of varnish will be helpful to those who are engaged in reducing or preventing varnish problems.

Background: To date, FM using middle ear packing has rarely reported. In this study, we hypothesized that middle ear packing with dexamethasone soaked gelfoam and fibrin glue over the fat graft could promote the success rate of TMP closure regardless of perforation size. Methods: Between January 2005 and July 2020, a total of 209 patients who underwent fat myringoplasty due to chronic TMP at tertiary referral center were encountered and analyzed. The success rate and audiologic outcome was analyzed. Results: The mean successful TM closure rate was 88.0 %. The success rate by different age generation was not significant difference. The size of the perforation grade showed no significant difference. The perforation site by anterior or posterior was not significant. The preoperative mean threshold of AC, BC and ABG were 55.71, 12.98 and 42.73 dB respectively. The postoperative mean threshold of AC, BC and ABG were 23.67, 12.98 and 10.69 dB. The change of preoperative and postoperative hearing showed statistically significant. Conclusion: From our results, the simple trimming of the perforation edge and middle ear packing with external ear canal packing using fibrin glue induced the stable adhesion between the remnant TM and the fat graft.

This study explores the application of numerical analysis and material models to predict ice impact loads on ships and offshore structures operating in polar regions. An explicit finite element analysis (FEA) approach was employed to simulate an ice and steel plate collision experiment conducted in a cold chamber. The pressure and strain history during the ice collision were calculated and compared with the experimental results. Various material model configurations were applied to the FEA to account for the versatile behavior of ice—whether ductile or brittle—its elastic-plastic yield criteria, and its dynamic strain rate dependency. In addition to the standard linear elastic perfectly plastic and linear elastic-plastic relationships, this study incorporated the crushable foam and Drucker-Prager models, based on the specific ice yield criteria. Considering the ice’s strain rate dependency, collision simulations were conducted for each yield criteria model to compute the strain and reaction force of the plate specimens. By comparing the predicted pressures for each material model combination with the pressures from ice collision experiments, our study proposes material models that consider the yielding, damage, and behavioral characteristics of ice. Lastly, our study proposes a combination of ice material properties that can accurately predict collision force.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

This research deals with risk assessment for human life, man-made infrastructure, and agriculture in a landslide-prone area using GIS-based spatial methods. The study area landslide inventory map was prepared based on previous landslide information, aerial photograph analysis, and several field observations. A total of 550 landslides have been included with 182 debris flow and 368 soil slides. All included landslides were classified into two groups by random selection; half were used for model calibration and the rest were used for cross-validation. In the analysis, fourteen causative factors were vastly used, such as aspect, slope, curvature, elevation, topographic wetness index, forest timber diameter, forest type, forest crown density, forest age, land-use, geology, soil drainage, soil depth, and soil texture. Moreover, to identify the interaction between occurred landslides and causative factors, the affected pixels were divided into different sub-classes using a frequency ratio method. Based on the total dataset, three landslide susceptibility maps were constructed using Bayesian prediction, likelihood ratio, and fuzzy set method. By evaluating cross-validation and success rate curve, model susceptibility results were plotted with a receiver operating characteristic (ROC) curve and the area under the curve (AUC) was estimated. In addition, for risk assessment, each social data layer such as agriculture, house, industry, business, road, river, population intensity, monetary value, and vulnerability level was added based on the local standard and incident time and was converted into US dollars. During the analysis, each method hazard map was used with a specific group of thematic data layers. Subsequently, for preparing the probability table, study area total pixels and predictive landslide affected pixels were considered. Matching with the affected pixels, a standard of 5000 pixels was selected to run the final evaluation. Based on the results, the agricultural field showed the highest vulnerability and estimated risk of US $ 16.3 million. Further, the man-made infrastructure map showed a risk of US $ 31.3 million. The total estimated population casualties were 6.77, which was relatively similar to the published data.

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

(1) Background: Ferric carboxymaltose (FCM) is an intravenous (IV) high-dose iron that is effective in the treatment of iron deficiency anemia. This study was to determine if preoperative IV FCM administration could improve recovery from postoperative anemia in patients undergoing revision total joint arthroplasty. (2) Methods: This prospective randomized controlled study analyzed 82 patients undergoing revision total joint arthroplasty during a single hospitalization. Patients in the iron group (n = 41) were administered 1000 mg of IV FCM two weeks preoperatively, while those in the control group (n = 41) were not. Moreover, patients with anemia defined as a preoperative suboptimal Hb concentration <13.0 g/dl were compared according to IV FCM administration. The absolute Hb levels and changes in Hb levels, iron profiles, transfusion rate, and EuroQOL 5-dimension (EQ-5D) scores were compared. (3) Results: There were no significant differences in recovery of Hb levels at each timepoint between the two groups; however, the changes in Hb levels from baseline to four weeks postoperatively showed marginally significant differences favoring the iron group (p = 0.052). However, for preoperatively anemic patients, the change in hemoglobin (Hb) levels between baseline and four weeks postoperatively was significantly better in the iron group than in the control group (iron group [n = 26], −0.3 ± 0.7 g/dL vs. control group [n = 27], −0.9 ± 0.8 g/dL; p = 0.040), although the absolute Hb levels, transfusion rates, and patient quality of life were comparable (all p > 0.05). The iron group showed improved iron metabolite levels including serum ferritin and transferrin saturation four weeks postoperatively, and no adverse events associated with IV FCM administration occurred in either group. (4) Conclusions: Preoperative IV FCM in anemic individuals undergoing revision joint arthroplasty was effective in accelerating recovery from surgery-related anemia by improving Hb levels without any adverse events, despite similar actual Hb levels between the groups. Our findings are clinically relevant and can facilitate determination of the suitability of IV FCM as a safe and reliable protocol for iron supplementation for anemia correction.

Submucosal invasion is a critical step in gastric cancer (GC) progression, which greatly enhances metastasis risk. Cancer stem cells are responsible for invasion, metastasis, and tumor growth. To identify stem cell-related markers associated with submucosal invasion in GCs, we investigated the expression of candidate cancer stem cell (CSC) markers (CD133, CD44, and ALDH1A) and intestinal stem cell (ISC) markers (EPHB2, OLFM4, and LGR5) in early GCs with submucosal invasion. Remarkably, expression of all ISC markers and CD133 was frequently confined to the basal area of the lamina propria (basal pattern) in mucosal cancer. The proportion of stem cell marker-positive cells substantially increased during submucosal invasion. Given that ISC markers are restricted to the crypt base of the normal intestinal mucosa, these findings suggest that many early GCs may retain hierarchical characteristics. CD44 expression showed a focal pattern, ALDH1A was predominantly expressed diffusely, and there was no expansion of CD44 or ALDH1A expression in the submucosal cancer cells. RSPO2 from muscularis mucosa seem to be partly responsible for the increased expression of ISC markers in GC cells at the basal areas. We also found that ISC markers were correlated with CDX2 expression in GCs, indicating that ISC markers are involved in the intestinal differentiation in GCs. Interestingly, ISC markers (EPHB2 and OLFM4) and CD133 showed a positive impact on clinical outcomes. In particular, the prognostic value of EPHB2 was significant for intestinal-type GCs in a multivariate analysis. In summary, ISC markers and CD133 showed a basal distribution pattern along with enhanced expression in submucosal invading cells in early GCs. EPHB2 was an independent prognostic marker in intestinal-type GCs.

In recent years, integration of electric vehicles (EVs) has increased dramatically due to their lower carbon emissions and reduced fossil fuel dependency. However, charging EVs could have significant impacts on the electrical grid. One promising method for mitigating these impacts is the use of renewable energy systems. Renewable energy systems can also be useful for charging EVs where there is no local grid. This paper proposes a new strategy for designing a renewable energy charging station consisting of wind turbines, a photovoltaic system, and an energy storage system to avoid the use of diesel generators in remote communities. The objective function is considered to be the minimization of the total net present cost, including energy production, components setup, and financial viability. The proposed approach, using stochastic modeling, can also guarantee profitable operation of EVs and reasonable effects on renewable energy sizing, narrowing the gap between real-life daily operation patterns and the design stage. The proposed strategy should enhance the efficiency of conventional EV charging stations. The key point of this study is the efficient use of excess electricity. The infrastructure of the charging station is optimized and modeled.

The association between the choice of general anesthetic agents and the risk of acute kidney injury (AKI) and long-term renal function after nephrectomy has not yet been evaluated. We reviewed 1087 cases of partial or radical nephrectomy. The incidence of postoperative AKI, new-onset chronic kidney disease (CKD) stage 3a and CKD upstaging were compared between different general anesthetic agent groups: propofol, sevoflurane, and desflurane. Four different propensity score analyses were performed to minimize confounding for each pair of comparison (propofol vs sevoflurane; propofol vs desflurane; sevoflurane vs desflurane; propofol vs volatile agents). Study outcomes were compared before and after matching. Kaplan-Meier survival curve analysis was performed to compare renal survival determined by the development of CKD stage 3a between groups up to 36 months after nephrectomy before and after matching. Propofol was associated with a lower incidence of AKI, CKD upstaging and a higher three-year renal survival after nephrectomy compared to sevoflurane or desflurane group after matching (AKI: propofol 23.2% vs. sevoflurane 39.5%, P=0.004, vs. desflurane 34.3%, P=0.031; CKD upstaging: propofol 27.2% vs. sevoflurane 58.4%, P<0.001, vs. desflurane 48.6%, P=0.017; Log-rank test propofol vs. sevoflurane P<0.001, vs. desflurane P=0.015). Propofol was also associated with a lower incidence of new-onset CKD after nephrectomy compared to sevoflurane after matching (P<0.001). However, there were no significant differences between sevoflurane and desflurane. In conclusion, propofol, compared to volatile agents, may be the reasonable choice of general anesthetic agent for nephrectomy to attenuate postoperative renal dysfunction. Randomized prospective trials are warranted to test this hypothesis.

: As antibiotic resistance undermines efforts to treat bacterial infections, phage therapy is being increasingly considered as an alternative in clinical settings and agriculture. However, a major concern in using phages is that pathogens will develop resistance to the phage. Due to the constant evolutionary pressure by phages, bacteria have evolved numerous mechanisms to block infection. If we determine the most common among them, we could use this knowledge to guide phage therapeutics. Here we compile data from 88 peer-reviewed studies where phage resistance was experimentally observed and linked to a bacterial gene, then assessed these data for patterns. In total, 141 host genes were identified to block infection against one or more of 80 phages (representing five families of the Caudovirales) across 16 microbial host genera. These data suggest that bacterial phage resistance is diverse, but even well-studied systems are understudied, and there are gaping holes in our knowledge of phage resistance across lesser-studied regions of microbial and viral sequence space. Fortunately, scalable approaches are newly available that, if broadly adopted, can provide data to power ecosystem-aware models that will guide harvesting natural variation towards designing effective, broadly applicable phage therapy cocktails as an alternative to antibiotics.

This study presents a method for the rapid and accurate generation of two-dimensional (2D) orthomosaic maps using selected image data collected by drone-captured video. The focus is on developing a real-time method capable of creating maps more quickly than image selection. The scale-invariant feature transform (SIFT) algorithm is applied to drone images to extract features in various scale regions. For feature point matching, a matching method based on the fast library for approximate nearest neighbors (FLANN) was adopted. A comparison of the computational speed of the FLANN with that of the k-nearest neighbors (KNN) and brute force matcher during the matching process revealed FLANN's superior capability for real-time data processing. The random sample consensus (RANSAC) algorithm was employed to enhance the accuracy of the matching by removing outliers, effectively identifying and eliminating mismatches, and reinforcing the reliability of feature point matching. The combination of SIFT, FLANN, and RANSAC algorithms demonstrates the capacity to process drone-captured image data in real time, facilitating the generation of precise 2D orthomosaic maps. The proposed method was assessed and validated using imagery obtained as the drone executed curvilinear and straight flight paths, confirming its accuracy and operational efficiency concurrently with the image capture process.

This paper proposes an algorithm for transmitting and reconstructing the estimated point cloud using temporally estimating a dynamic point cloud sequence. When a non-rigid 3D point cloud sequence (PCS) is input, the sequence is divided into groups of point cloud frames (PCF), and a key PCF is selected. After the 3D skeleton is predicted through 3D pose estimation, the motion of the skeleton is estimated by analyzing the joints and bones of the 3D skeleton. For the deformation of the non-rigid human PC, the 3D PC model is transformed into a mesh model, and the key PCF is rigged using the 3D skeleton. After deforming the key PCF into the target PCF utilizing the motion vector of the estimated skeleton, the residual PC between the motion compensation PCF and the target PCF is generated. If there is a key PCF, the motion vector of the target PCF, and a residual PC, the target PCF can be reconstructed. Just as compression is performed using pixel correlation between frames in a 2D video, this paper compresses 3D PCF by estimating the non-rigid 3D motion of a 3D object in a 3D PC. The proposed algorithm can be regarded as an extension of the 2D motion estimation of a rigid local region in a 2D plane to the 3D motion estimation of a non-rigid object (human) in 3D space. Experimental results show that the proposed method can successfully compress 3D PC sequences. If it is used together with a PC compression technique such as MPEG PCC (point cloud compression) in the future, a system with high compression efficiency may be configured.

Reinforcement Learning (RL) has demonstrated considerable potential in solving challenges across various domains, notably in autonomous driving. Nevertheless, implementing RL in autonomous driving comes with its own set of difficulties, such as the overestimation phenomenon, extensive learning time, and sparse reward problems. Although solutions like Hindsight Experience Replay (HER) have been proposed to alleviate these issues, the direct utilization of RL in autonomous vehicles remains constrained due to the intricate fusion of information and the possibility of system failures during the learning process. In this paper, we present a novel RL-based autonomous driving system technology that combines Obstacle Dependent Gaussian (ODG) RL, Soft Actor-Critic (SAC), and meta-learning algorithms. Our approach addresses key issues in RL, including the overestimation phenomenon and sparse reward problems, by incorporating prior knowledge derived from the ODG algorithm. We evaluated our proposed algorithm on official F1 circuits, using high-fidelity racing simulations with complex dynamics. The results demonstrate exceptional performance, with our method achieving up to 89% faster learning speed compared to existing algorithms in these environments.

This paper presents a study aimed at enhancing the performance of quantum dot light-emitting didoes (QLEDs) by employing a solution-processed molybdenum oxide (MoO3) nanoparticle (NP) as a hole injection layer (HIL). The study investigates the impact of varying the concentrations of the MoO3 NP layer on device characteristics and explores the underlying mechanisms responsible for the observed enhancements. Experimental techniques such as an X-ray diffraction and field-emission transmission electron microscopy were employed to confirm the formation of MoO3 NPs during the synthesis process. Ultraviolet photoelectron spectroscopy is employed to analyze the electron structure of the QLEDs. The QLED with an 8 mg/mL concentration of MoO3 nanoparticles achieves remarkable improvements in device performance, with a maximum luminance of 69,240.7 cd/cm2, maximum current efficiency of 56.0 cd/A, and maximum external quantum efficiency (EQE) of 13.2%. The obtained results signify a notable progress in comparison to QLED without HIL and those utilizing the widely used poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) HIL. They exhibit a remarkable enhancement of 59.5% and 26.4% in maximum current efficiency, respectively, as well as a significant improvement of 42.7% and 20.0% in maximum EQE, respectively. This study opens up new possibilities for the selection of HIL and the fabrication of solution-processed QLEDs, contributing to the potential commercialization of these devices in the future.

Dengue fever is a persistent public health issue in tropical regions, including Vietnam, where climate variability plays a crucial role in disease transmission dynamics. This study focuses on developing climate-based machine learning models to forecast dengue outbreaks in Ba Ria Vung Tau (BRVT) province, Vietnam, using meteorological data from 2003 to 2022. We utilized four predictive models—Negative Binomial Regression (NBR), Seasonal AutoRegressive Integrated Moving Average with Exogenous Regressors (SARIMAX), Extreme Gradient Boosting (XGBoost), and Long Short-Term Memory (LSTM)—to predict weekly dengue incidence. Key climate variables, including temperature, humidity, precipitation, and wind speed, were integrated into these models, with lagged variables included to capture delayed climatic effects on dengue transmission. The NBR model demonstrated the best performance in terms of predictive accuracy, achieving the lowest Mean Absolute Error (MAE) compared to other models. The inclusion of lagged climate variables significantly enhanced the model’s ability to predict dengue cases. SARIMAX and LSTM models, although effective in capturing seasonal trends, struggled with overfitting and failed to accurately predict short-term outbreaks. XGBoost exhibited moderate predictive power but was sensitive to overfitting, particularly without fine-tuning. Our findings confirm that climate-based machine learning models, particularly the NBR model, offer valuable tools for forecasting dengue outbreaks in BRVT. However, improving the models’ ability to predict short-term peaks remains a challenge. The integration of meteorological data into early warning systems is crucial for public health authorities to plan timely and effective interventions. This research contributes to the growing body of literature on climate-based disease forecasting and underscores the need for further model refinement to address the complexities of dengue transmission in highly endemic regions.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

Intra-abdominal pressure (IAP) elevation during capnoperitoneum can cause adverse cardiovascular and respiratory effects. This study aimed to determine if a sequentially increased IAP affects cardiovascular and respiratory variables in anesthetized dogs and evaluate the effects of constant rate infusion of dexmedetomidine (Dex) on cardiovascular and respiratory variables with increased IAP. Five dogs were anesthetized, instrumented, and the Veress needle was equipped to adjust the IAP using a carbonic anhydrase insufflator. Stabilization was conducted for 1 h, and physiological variables were measured in IAPs of 0, 5, 10, 15, and 20 mmHg and after desufflation. After the washout period, the dogs underwent similar procedures along with constant rate infusion of dexmedetomidine. Cardiovascular effects of increased IAP up to 20 mmHg were not significant in healthy beagle dogs and those administered with dexmedetomidine. In the control group, the arterial pressure slightly increased, but not statistically significant, at an IAP of 20 mmHg compared with that at baseline (mean arterial blood pressure, p = 0.399; systolic arterial blood pressure, p = 0.293; diastolic arterial blood pressure, p = 0.141). When comparing the control and dexmedetomidine groups, overall significant effects of dexmedetomidine were noted on heart rate, cardiac output, and systemic vascular resistance during the experiment. Respiratory effects were not affected by abdominal insufflation when compared between different IAPs and between the two groups. Overall, an increased IAP of until 20 mmHg did not significantly affect cardiovascular and respiratory variables in both control and dexmedetomidine groups. This study suggests that dexmedetomidine infusion administration is applicable in laparoscopic procedures in healthy dogs.

Background: Idiopathic pulmonary fibrosis (IPF) is a progressive fibrotic lung disease with a poor prognosis. Pirfenidone is approved and widely used for the treatment of IPF and reduces lung function decline. The aim of this study was to evaluate the efficacy of different doses of pirfenidone for the prevention of disease progression in patients with IPF. Methods: This was a prospective, observational, single-center cohort study conducted in Haeundae Paik Hospital, Republic of Korea, from April 2021 to March 2023. IPF patients were assigned to three groups according to the dose of pirfenidone (600mg, 1,200mg, 1,800mg). The primary endpoint was the efficacy of pirfenidone according to dose for the prevention of disease progression over 12 months. The secondary endpoint was the role of Krebs von den Lungen-6 (KL-6) in predicting disease progression. Results: A total of 44 patients were enrolled, of whom 39 completed the study, with 13 patients assigned to each of the three groups. The median age was 71.7 years, and 79.5% of patients were men. The baseline characteristics were similar across groups, except the 600mg group was older (75.9 vs. 69.2 vs. 68.2 years, p = 0.016). Fourteen patients (35.9%) suffered disease progression. The rate of disease progression did not differ according to the dose of pirfenidone (38.5 vs. 38.5 vs. 30.8%, p = 1.000). In multivariable logistic regression analysis, KL-6 was not a statistically significant predictor of disease progression. Conclusions: In our study, regardless of dose, consistent pirfenidone use for 12 months resulted in similar efficacy for the prevention of disease progression in patients with IPF. Large-scale, randomized, double-blind, placebo-controlled clinical trials are needed.

The Hwangdo tidal flat is an intertidal landform located in Cheonsu Bay, Taean-gun, Chungcheongnam-do, on the west coast of Korea. The topographical characteristics of the semi-enclosed bay on the eastern side of the study area include waterways, sandbars, small islands, and tidal flats. In this study, data were acquired from tide gauges installed on the Hwangdo Bridge, and the height of the ellipsoid was measured using a real-time kinematics global positioning system (RTK-GPS). Digital elevation model (DEM) using Matrice 300 drone data were also acquired after processing. The geochemical sediment characteristics in the study area were analyzed, together with tidal-flat exposure-time characteristics based on environmental factors. Sediment data (n = 107) collected from October 25 to 28, 2022 (Korean local time) were used to classify sediment particles according to Folk and Ward (1957). Sedimentary facies ranged from coarse sand (sand:mud ratio = 9:1) to sandy silt (sZ) followed by muddy sand (mS) and slightly gravelly sandy mud ((g)sM). Total organic carbon (TOC) in the surface sediments were also characterized based on a particle-size analysis. The mean change in tidal height measured at Hwangdo Bridge during the sampling period was ~7.53 m (minimum: –3.86 m, maximum: +3.67 m). Based on the Boryeong's sea level measurement tide data in 2022, the tidal area in the drone images ranged from 6.362 m² (0.006 km²) at DEM +4.0 to 4,841,078 m² (4.841 km²) at DEM –4.0 m, indicating an increase in the tidal-flat area according to the tidal level of up to ~800-fold. The daily average exposure time was 9.0 h (minimum: 1.5 h, maximum: 17.9 h). Based on the results of multivariate analysis using exposure times and a geochemical dataset, four groups were identified: upper, middle, and lower intertidal zones and regions with a relatively high organic-matter concentration. A determination of the main characteristics of the Hwangdo tidal flat according to their spatial distribution showed that, among various environmental factors, changes in the sand or clay sediment composition were determined by community factors. The results of this study demonstrate the four statistically processed groups of marine environmental characteristics in the Hwangdo tidal flats. Changes in sedimentary patterns, rather than in the exposure time, accounted for the differences in the sediment compositions of the upper, middle, and lower stations, a response that is expected to continue.

This study was conducted on elderly over 65 years of age to verify that healing garden activities control stress in the elderly. The experimental group performed garden activities once a week for 12 weeks, 2 hours each, and the control group continued their daily lives. Each group's cumulative stress at the beginning and end, total power (TP), the standard deviation of the normal-to-normal interval (SDNN), and root mean square differences of successive R-R intervals (RMSSD) were measured using a stress index meter, u-bio MACPA. As a result of the analysis, the experimental group had a statistically significant decrease in cumulative stress compared to the control group, and TP significantly increased compared to the control group. SDNN and RMSSD of the experimental group increased, respectively, and the control group decreased, respectively, but it was not statistically significant. The fact that cumulative stress decreased, and stress evaluation indicators increased shows that daily stress can be controlled through healing garden activities. This confirms that the value of the garden can extend to healing.

To determine the mode of action of the effects of phytoalexins in soybeans, we analyzed enzyme inhibition kinetics using Michaelis–Menten plots and the Lineweaver–Burk plots. The results showed that glyceollin showed competitive inhibition, genistein showed noncompetitive, daidzein was uncompetitive, and luteolin showed a mixed mode of action. The Ki values were determined using a Dixon plot as: glyceollin, 18.99; genistein, 15.42; luteolin, 16.81; and daidzein, 9.99 μM, respectively. Furthermore, potential synergistic effects between glyceollin and the three designated polyphenols were investigated. A combination of glyceollin and luteolin (the ratio of 3:7 of glyceollin and luteolin) had synergistic effects on α-glucosidase inhibition according to combination index (CI)-isobologram equation. Collectively, these results showed that a combination of glyceollin and luteolin has the potential to inhibit α-glucosidase activity via a synergistic mode of action.

Goal-conditioned reinforcement learning (RL) holds promise for addressing intricate control challenges by enabling agents to learn and execute desired skills through separate decision modules. However, the irregular occurrence of required skills poses a significant challenge to effective learning. In this paper, we demonstrate the detrimental effects of this imbalanced skill(sub-goal) distribution and propose a novel training approach, Classified Experience Replay (CER), designed to mitigate this challenge. We demonstrate that adapting our method to conventional RL methods significantly enhances the performance of the RL agent. Considering the challenges inherent in tasks such as driving, characterized by biased occurrences of required sub-goals, our study demonstrates the improvement in trained outcomes facilitated by the proposed method. In addition, we introduce a specialized framework tailored for self-driving tasks on highways, integrating Model Predictive Control (MPC) into our RL trajectory optimization training paradigm. Our approach, utilizing CER with the suggested framework, yields remarkable advancements in trajectory optimization for RL agents operating in highway environments.

Driven by industrialization and urbanization, urban air pollution can increase respiratory, heart, and cerebrovascular diseases, and thus mortality rates; as such, it is necessary to improve air quality through the consideration of individual pollutants and emissions sources. In South Korea, national and local governments have installed urban and roadside air quality monitoring systems. However, stations are lacking outside metropolitan regions, and roadside stations are sparsely distributed, limiting comparisons of pollutant concentrations with vehicle traffic and floating population levels. Local governments have begun using mobile laboratories (MLs) to supplement the fixed measurement network and investigate road pollution source characteristics based on their spatiotemporal distribution; however, the collected data cannot be used effectively if they are not visualized. Here, we propose a method to collect and visualize global information system (GIS)-based air quality data overlayed with environmental variables to support air quality management measures. Spatiotemporal analyses of ML-derived data from Bucheon, Korea, confirmed that particulate and gaseous pollutant concentrations were high during typical commuting hours, at intersections, and at a specially managed road. During commuting hours, the maximum PM10 concentration reached 200.7 µg/m³ in the Nae-dong, Gyeongin-ro, and Ojeong-dong ready-mix concrete complex areas, and the maximum PM_2.5 concentration was 161.7 µg/m³. The maximum NOx, NO₂, and NO levels of 1.34 ppm, 0.18 ppm, and 1.18 ppm, respectively, were also detected during commuting hours. These findings support the need for targeted management of air pollution in this region, and highlight the benefit of comprehensively comparing road levels, driving speed, and traffic levels when identifying hotspots of air pollution. Such analyses will contribute to the development of air quality management measures customized to regional characteristics.

Quorum sensing (QS) is a sophisticated bacterial cell-to-cell communication mechanism that allows bacteria to sense population density through the secretion and detection of diffusible small molecular signals. This process leads to the coordinated expression of specific genes at the transcriptional level. Over time, continuous research has elucidated the genetic elements and regulatory principles of QS. Recently, synthetic biology has leveraged these insights to construct genetic circuits incorporating QS components, enabling both intra-species and inter-species artificial communication. These QS-based genetic circuits hold significant potential for applications in biotechnology and biomedicine. This paper reviews several well-characterized microbial QS systems and their functional roles, while also introducing the application of QS-based genetic circuits in cellular communication across species. The paper further discusses the role of QS in the development of biological computing tools, population density regulation, and metabolic flux control, offering a forward-looking perspective on future advancements. For intra-species communication, the focus is on the use of QS systems in constructing biological computing tools, including toggle switches, biosensors, and logic gates in synthetic biology. These tools, designed on the QS mechanism, can more precisely coordinate cellular behavior by integrating biological control circuits to achieve spatial, temporal, and population-level regulation. In the context of inter-species communication, the introduction of QS systems plays a pivotal role in population density control and metabolic flow regulation. By recombining metabolic networks, QS enables the redistribution of metabolic flux in desired pathways, facilitating the regulation of population density and the co-culture of mixed strains. Moreover, combining QS with oscillator models has shown great potential in synchronizing microbial communities. In summary, in-depth research into QS mechanisms and their applications not only lays a solid foundation for understanding microbial ecological competition and dynamic balance, but also offers promising avenues for regulating pathogenic bacteria and developing innovative disease control strategies.

Candida albicans, a prominent constituent of the human microbiota, poses a significant health threat due to its opportunistic pathogenicity and adept biofilm-forming capabilities. This research delves into the antifungal attributes and biofilm inhibition potential of Tea Tree Oil (Melaleuca alternifolia) cultivated in Vietnam. Renowned for its bioactive compounds, including terpinen-4-ol, 1,8-cineole, and terpinolene, the essential oil of Melaleuca alternifolia, commonly referred to as tea tree oil (TTO), is scrutinized for its impact on Candida albicans. The study meticulously determines the Minimum Inhibitory Concentration (MIC) and Minimum Fungicidal Concentration (MFC) of TTO against Candida albicans in both planktonic and biofilm states. Additionally, it assesses the biofilm-forming capacity of Candida albicans and establishes the Minimum Biofilm Inhibitory Concentration (MBIC) and Minimum Biofilm Eradication Concentration (MBEC) of TTO. Employing a liquid culture dilution method within a defined concentration range of 0.1 μL/mL to 10 μL/mL, the experimental approach adheres to established protocols. The outcomes reveal a noteworthy MIC and MIC₈₀ of 0.1 μL/mL and 2 μL/mL, respectively, and an MFC of 10 μL/mL for TTO against Candida albicans. Furthermore, TTO exhibits an MBIC of 2 μL/mL, showcasing its efficacy in inhibiting biofilm formation. However, the MBEC of TTO remains uncertain, possibly due to insufficient concentration tested, which may not effectively disrupt over 50% of the pre-formed biofilm mass within 24 hours. These results underscore the promising potential of TTO as a potent antifungal agent and biofilm inhibitor against Candida albicans, offering valuable insights for the innovation of novel therapeutic strategies in the realm of fungal infections.

Background: Identifying genetic mutations that lead to spermatogenic impairment is essential for offering patients informed genetic counseling and preventing the transmission of genetic defects to their offspring, often through the use of advanced reproductive technologies. Objectives: The purpose of this study was to identify potential single nucleotide polymorphisms (SNPs) associated with male infertility. Methods and Materials: Genetic variants that may cause infertility are identified by combining targeted next generation sequencing (NGS) panel and whole exome sequencing (WES). The validation step of Sanger sequencing adds confidence to the identified variants. Results: Our analysis revealed five distinct affected genes covering seven SNPs: based on targeted NGS panel and WES data, namely SPATA16 (rs16846616, 1515442, 1515441), CFTR (rs213950), KIF6 (rs2273063), STPG2 (r2903150) and DRC7 (rs3809611). Infertile men have a higher mutation rate than fertile men, especially those with azoospermia. Discussion and Conclusions: These findings strongly support the hypothesis that dysfunction of microtubule-related and spermatogenesis-specific genes contributes to idiopathic male infertility. The SPATA16, CFTR, KIF6, STPG2 and DRC7 mutations are associated with male infertility, specifically azoospermia, further examination of this genetic function is required.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

The Korean Pathfinder Lunar Orbiter (KPLO)-MAGnetometer (KMAG) consists of three triaxial fluxgate sensors (MAG1, MAG2, and MAG3) to measure the magnetic field around the Moon. The three sensors are mounted in the order of MAG3, MAG2, and MAG1 inside a 1.2 m long boom away from the satellite body. Before it arrived on the Moon, we compared the magnetic field measurements taken by DSCOVR and KPLO in the solar wind to verify the measurement performance of the KMAG instrument. We found that there were artificial disturbances in the KMAG measurement data, such as step-like and spike-like disturbances, which were produced by the spacecraft body. To remove spacecraft-generated disturbances, we applied a multi-sensor method, employing the gradiometer technique and principal component analysis and using KMAG magnetic field data and confirmed the successful elimination of spacecraft-generated disturbances. This indicates that the multi-sensor method is able to clean the magnetic field data measured onboard the KPLO.

In this study, ozone oxidation experiment was carried out for the removal of fluorescent whitening agent which is widely used in textile dyeing and paper industry. The stilbene fluorescent whitening agent has been industrialized since the earliest, and the amount of current production is the highest. Due to the characteristics of the fluorescent whitening agent that cannot be removed by conventional wastewater treatment methods, the fluorescent whitening agent in wastewater treatment has difficulty in using as recycled water in the process. Pre-treatment ozone oxidation experiment was conducted prior to the introduction of Membrane Bio Reactor (MBR) treatment process by converting biodegradable materials into biodegradable materials. The removal efficiencies of fluorescent whitening agents, a diaminostilbene disulfonic acid derivative by ozone oxidation were evaluated by UV254 Scan, COD, T-N and color using a synthetic wastewater sample (COD=433.0 mg/ℓ) and paper and paper mill wastewater (COD=157.2 mg/ℓ).

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

Excessive oxidative stress and exercise-induced fatigue reduce physical performance and can lead to dysfunction in antioxidant systems within muscular and hepatic tissues. Integrating natural substances with exercise may mitigate fatigue via anti-oxidant effects. This study aims to compare and evaluate the effects of exercise and supplementation with Sundarbans honey vs energy drinks on the strength, anxiety physiological profiles, and hepatic antioxidant capacity in mice undergoing extraneous exercise and fatigue. Forty-eight four-week-old Swiss albino mice were randomly assigned to one of eight groups: (1) Control, (2) Speed™ (Sp), (3) Royal Tiger™ (RT), (4) Sundarbans Honey (SH), (5) Exercise (Ex), (6) Exercise + Sundarbans Honey (Ex+SH), (7) Exercise + Speed™ (Ex+Sp), and (8) Exercise + Royal Tiger™ (Ex+RT). Supplements were administered via oral gavage: Sp (2.5 ml/kg BW), RT (2.5 ml/kg BW), and SH (1 g/kg BW), four times a week for 60 days. Mice in the Ex, Ex+SH, Ex+Sp, and Ex+RT groups underwent daily swimming and running. The strength, fatigue, anxiety levels, lipid profiles, and antioxidant biomarkers were evaluated post-treatment. The SH, Ex, and Ex+SH groups exhibited significantly enhanced physical performance (p<0.05). Plasma lipid profiles, including LDL, triglycerides, total cholesterol, and fatigue-related biomarkers (ALP, AST, ALT, LDH, CK, LA, BUN, and glucose) were markedly increased in the Sp and RT groups but decreased in the SH, Ex, and Ex+SH groups compared to control (p<0.05). Exercise-induced fatigue elevated the Nrf2/HO-1 antioxidant defense system in liver tissue. IL-6 levels were reduced in the SH, Ex, and Ex+SH groups (p<0.05). These findings indicate that regular exercise combined with SH supplementation increases strength and improves lipid profiles, reducing exercise-induced oxidative stress and fatigue via modulation of the Nrf2/HO-1 pathway in liver tissue. These results highlight SH supplementation’s potential as a complementary strategy to enhance exercise outcomes and mitigate exercise-induced stress.

Exposure to cadmium sulfate (CdSO4) can lead to neurotoxicity. Nevertheless, the precise molec-ular mechanisms underlying this phenomenon remain unclear, and effective treatment strategies are scarce. This study explored the protective effects of ellagic acid (EA), a natural polyphenolic compound, against CdSO4 exposure-induced neurotoxicity in HT22 cells. Additionally, the inves-tigation sought to elucidate the molecular mechanisms underlying this phenomenon. Our findings demonstrated that exposure of HT22 cells to CdSO4 resulted in apoptosis, which was effectively reversed by EA supplementation. EA supplementation also decreased reactive oxygen species (ROS) and mitochondrial ROS productions, reduced malondialdehyde (MDA) levels, and restored the activities of superoxide dismutase (SOD) and catalase (CAT). Additionally, EA supplementation at 5–20 μM significantly counteracted Cd-induced mitochondrial membrane potential and ATP losses and reduced the ratio of Bax/Bcl-2 and cleaved-caspase-3 protein expression. Furthermore, EA supplementation upregulated Nrf2 and HO-1 protein expression while downregulating the phosphorylation of JNK and p38 proteins. Pharmacological inhibition of JNK partially inhibited CdSO4-induced Nrf2/HO-1 activation and exacerbated its cytotoxicity. In conclusion, our results indicate that EA supplementation provides protection against CdSO4-induced cell apoptosis in HT22 cells by inhibiting oxidative stress and activating the Nrf2 pathway. Activation of the JNK pathway plays a protective role in CdSO4-induced cell apoptosis in HT22 cells.

Dengue fever remains one of the most significant public health challenges globally, particularly in tropical and subtropical regions. Traditional early warning systems (EWS) for dengue outbreaks, based on retrospective epidemiological data, suffer from delays and limited predictive accuracy. Modern systems, leveraging real-time data, artificial intelligence (AI), and machine learning (ML), improve accuracy but can be costly and difficult to implement in resource-constrained settings. This paper proposes a novel hybrid model that integrates the strengths of both traditional and modern EWS, with real-world examples from Brazil, and Malaysia. The hybrid model balances accuracy, scalability, and cost-effectiveness, making it a feasible option for low- and middle-income countries.

Background and aim. The study aimed to assess the efficacy of the treatment of Kan Jang®, a fixed combination of Andrographis paniculata (Burm. F.) Wall. ex. Nees and Eleutherococcus senticosus (Rupr. & Maxim.) Maxim in patients with mild symptoms of COVID-19. Methods. One hundred forty patients received six capsules of Kan Jang® (n = 68, daily dose of andrographolides – 90 mg) or placebo (n=72) and supportive treatment (paracetamol) for 14 consecutive days in a randomized, quadruple-blinded, placebo-controlled, two-parallel-group design. The efficacy outcomes were the rate of cases turning to severe, the detection rate of SARS-CoV-2 virus over the time of treatment, the duration and the severity of symptoms (sore throat, runny nose, cough, headache, fatigue, loss of smell, taste, pain in muscles) in the acute phase of the disease. Other efficacy measures included improving cognitive and physical performance, quality of life, and the levels of inflammatory blood markers - IL-6, c-reactive protein, and D-dimer. Results. Kan Jang® significantly (p < 0.05) reduced the rate of cases turning to severe (5.36%) compared to placebo (17.86%) and decreased the detection rate of SARS-CoV-2 virus over the time of treatment. The statistical difference in the rates of patients with clinical deterioration in the Kan Jang treatment and placebo control groups was significant (p = 0.0176) both in 112 patients included per protocol (IPP) analysis and in 140 patients included per intention to treat (ITT) analysis (p = 0.0236); the absolute risk reduction of cases by Kan Jang treatment was 12.5%, and the number Needed to Treat by Kan Jang was 8. The patient's recovery time (Number of sick days at the home/clinic) was shorter in the Kan Jang group compared with the placebo group. The rate of resolution of inflammatory symptoms in the Kan Jang® group was significantly higher compared with the placebo group, and relief of the severity of cough, sore throat/pain, runny nose, and muscle soreness. Kan Jang® significantly decreased the Wisconsin Upper Respiratory Symptoms scores compared to placebo in the sample size of 140 patients. However, the relief of fatigue and headache and the decrease of IL-6 in the blood was observed only in a subset of the 86 patients infected during the second three waves of the pandemic. Kan Jang® significantly increased physical activity and workout; however, it did not affect cognitive functions (attention and memory), Quality of life Score, inflammatory markers D-dimer, and c-reactive protein compared with the placebo group. Conclusions. Overall, the results of this study suggest that Kan Jang® is effective in treating mild and moderate COVID-19 irrespective of SARS-Cov-2 variants infection.

Six solvent fractions isolated from flower bud and leaf ethanolic extracts of Cleistocalyx operculatus were analyzed for their phytochemical contents including phenolics, flavonoids, saponins, tannins, and alkaloids. Antioxidant activities were measured using the ABTS, DPPH, and FRAP assays. The results showed that flower bud aqueous fraction (BAF) and leaf aqueous fraction (LAF) rich in phenolic content (768.18 and 490.74 mg GAE/g dry extract, respectively) exhibited significantly higher antioxidant activities than other fractions. Flower bud hexane fraction (BHF) had remarkably high flavonoid and saponin contents (134.77 mg QE/g and 153.33 mg OA/g dry extract, respectively), followed by that of leaf hexane fraction (LHF) (76.54 mg QE/g and 88.25 mg OA/g dry extract, respectively). BHF and LHF were found to have extremely high antibacterial activity against two H. pylori strains ATCC 51932 and 43504 (MICs of 125 µg/ml). Interestingly, DMC (2’,4’-Dihydroxy-6’-methoxy-3’,5’-dimethylchalcone) isolated from BHF displayed greater antibacterial activity against the bacterial strains (MICs of 25–50 µg/ml) than those of the fractions. In addition, DMC presented potent inhibitory effects on H. pylori-urease (IC50 of 3.2 µg/ml) and α-amylase (IC50 of 83.80 µg/ml), but no inhibition against α-glucosidase. It was also demonstrated that DMC showed its pronounced inhibitory effects on urease activity and biofilm formation of H. pylori, and could increase the membrane permeability of the bacterial cells. Scanning electron micrographs depict that BHF and DMC had strong effects on the cell shape and significantly induced distortion and damage of the cell membrane. The fractions and DMC showed no significant toxicity to four tested human cell lines. Efforts to reduce antibiotic use indicate the need for further researches of the flower buds and DMC as potential products to prevent or treat gastric H. pylori infections.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

This study reports rapid hydrolysis, acylation, and lipolysis with lipase B from Candida antarctica (CalB) and nanofructosome encapsulated CalB (CalB@NF) enzymes immobilized on silica-coated magnetic nanoparticles (Si-MNPs). Enzymatic hydrolysis was confirmed for conversion to p-nitrophenol (p-NP, λex=400 nm) from p-nitrophenyl butyrate (p-NPB, λex=270 nm), and various catalytic parameters such as Km, Vmax, and Kcat were calculated from Michaelis-Menten and Lineweaver-Burk plot. Efficiency of enzymatic hydrolysis was in the order of CalB > Si-MNPs@CalB > CalB@NF > Si-MNPs@CalB@NF, and reusability was much better with the enzyme immobilized on Si-MNPs than with the native enzyme. Enzymatic acylation was confirmed by the formation of benzyl benzoate (λex=229 nm) from benzoic anhydride (λex=240 nm), and efficiency exceeded 99% in all samples. Finally, enzymatic lipolysis was confirmed by the decomposition of olive oil to fatty acid such as oleic acid (λex=230 nm) using thin-layer chromatography (TLC), column chromatography, and proton nuclear magnetic resonance (1H -NMR). The lipases immobilized on Si-MNPs have the advantage of good thermal stability and reusability and are thus applicable to a wide range of industries.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Microbial production is a promising method that can overcome major limitations in conventional methods of lycopene production, such as low yields and variations in product quality. Significant efforts have been made to improve lycopene production by engineering either the 2-C-methyl-D-erythritol 4-phosphate (MEP) pathway or mevalonate (MVA) pathway in microorganisms. To further improve lycopene production, it is critical to utilize metabolic enzymes with high specific activities. Two enzymes, 1-deoxy-D-xylulose-5-phosphate synthase (Dxs) and farnesyl diphosphate synthase (IspA), are required in lycopene production using MEP pathway. Here, we evaluated the activities of Dxs and IspA of Vibrio sp. dhg, a newly isolated and fast-growing microorganism. Considering that the MEP pathway is closely related to the cell membrane and electron transport chain, the activities of the two enzymes of Vibrio sp. dhg were expected to be higher than the enzymes of E. coli. We found that Dxs and IspA in Vibrio sp. dhg exhibited 1.08-fold and 1.38-fold higher catalytic efficiencies, respectively. Consequently, the heterologous overexpression improved the specific lycopene production by 1.88-fold. Our findings could be widely utilized to enhance production of lycopene and other carotenoids.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

The vascular endothelium is key target for immune, and thrombotic responses that has to be controlled in successful xenotransplantation. Several genes were identified that if induced or overexpressed help to regulate the inflammatory response and preserve the transplanted organ function and metabolism. However, few studies addressed combined expression of such genes. The aim of this work was to evaluate in vivo the effects of the simultaneous expression of a three human genes in a mouse generated using the multi-cistronic F2A technology. Male 3-month-old mice that express human heme oxygenase 1 (hHO-1), ecto-5’-nucleotidase (hE5NT), and ecto-nucleoside triphosphate diphosphohydrolase 1 (hENTPD1) (Transgenic) were compared to wild-type FVB mice (Control). Background analysis include extracellular nucleotide catabolism enzymes profile on the aortic surface, blood nucleotide concentration and serum L-arginine metabolites. Furthermore, inflammatory stress induced by LPS in transgenic and control mice was used to characterize interleukin 6 (IL-6) and adhesion molecules endothelium permeabil-ity responses. Transgenic mice had significantly higher rates of extracellular adenosine triphosphate and adenosine monophosphate hydrolysis on the aortic surface in comparison to control. Increased levels of blood AMP and adenosine were also noticed in transgenics. Moreover, transgenic ani-mals demonstrated the decrease in serum monomethyl-L-arginine level and a higher L-arginine/ monomethyl-L-arginine ratio. Importantly, significantly decreased serum IL-6, and adhesion mol-ecule levels were observed in transgenic mice in comparison to control after LPS treatment. Fur-thermore, reduced endothelial permeability in the LPS-treated transgenic mice was noted as com-pared to LPS-treated control. The human enzymes (hHO-1, hE5NT, hENTPD1) simultaneously encoded in transgenic mice demonstrated benefits in sev-eral biochemical and functional aspects of endothelium. This is consistent in use of this approach in the context of xenotransplantation.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

In this study, the influence of graphene oxide nanoparticles on the bond-slip behavior of fiber and fly ash based geopolymer paste was examined. Geopolymer paste incorporating graphene oxide nanoparticles solution was cast in half briquetted specimens and embedded with a fiber. Three types of fibers were used: steel, polypropylene, and basalt. The pullout test was performed at two distinct speeds: 1 mm/second and 3 mm/second. Results showed that the addition of graphene oxide increased the compressive strength of geopolymer by about 7%. The bond-slip responses of fibers embedded in geopolymer mixed with graphene oxide exhibited higher peak stress and toughness as compared to those embedded in normal geopolymer. Each fiber type also showed different mode of failure. Both steel and polypropylene fibers showed full bond-slip responses due to their high ductility. Basalt fiber, on the other hand, because of its brittleness, failed by fiber fracture mode which showed no-slip in pull out responses. Both bond strength and toughness were found to be rate sensitive. The sensitivity was higher in graphene oxide/geopolymer than in conventional geopolymer.

This study aimed to compare the prognosis and characteristics of patients with advanced hepatocellular carcinoma treated with first-line atezolizumab plus bevacizumab (AB) combination therapy and hepatic artery infusion chemotherapy (HAIC). We retrospectively assessed 179 and 72 patients treated with HAIC and AB combination therapy, respectively, between January 2018 and January 2023. The progression-free survival of patients treated with HAIC was significantly superior than that of patients treated with AB (P&lt;0.05), but there was no significant difference in overall survival and objective response rate (ORR) between the two groups (P=0.1056 and P=0.137, respectively). After propensity score matching (PSM), our data revealed that there was no significant difference in PFS between patients who received AB combination therapy and HAIC therapy (P=0.8888). However, patients who received AB combination therapy had significantly better overall survival than those who received HAIC therapy (P=0.0133). In addition, after PSM, significant differences in ORR and disease control rate were not observed. In conclusion, our propensity score study reveals that patients treated with AB therapy have a significantly longer OS than those treated with HAIC.

Ongoing climate change causes abnormal climate events worldwide such as increasing temperatures and changing rainfall patterns. With South Korea facing growing damage from the increased frequency of localized heavy rains, the country is not an exception. In particular, its steep slope lands, including mountainous areas, are vulnerable to damage from landslides and debris flows. In addition, localized short-term heavy rains that occur in urban areas with extremely high intensity tend to lead a sharp increase in damage from soil-related disasters and cause huge losses of life and property. Currently, South Korea predicts landslides and debris flows using the standards for forecasting landslides and heavy rains. However, as the forecasting is conducted separately for rainfall intensity and accumulated rainfall, this lacks a technique that reflects both amount and intensity of rainfall in an episode of localized heavy rainfall. This study, therefore, aims to develop such a technique by collecting past cases of debris flow occurrences and rainfall events that accompanied debris flows to calculate the rainfall triggering index (RTI) reflecting accumulated rainfall and rainfall intensity. In addition, the RTI is converted into the critical accumulated rainfall (Rc) to use precipitation information and provide real-time forecasting. The study classifies the standards for flow debris forecasting into three levels: ALERT (10%–50%), WARNING (50%–70%), and EMERGENCY (70% or higher), to provide a nomogram for 6 hr, 12 hr, and 24 hr. As a result of applying this classification into the actual cases of Seoul, Chuncheon, and Cheongju, it is found that about 2–4 hr of response time is secured from the point of the Emergency level to the occurrence of debris flows.

Explainable AI (XAI) has emerged as a pivotal tool in healthcare diagnostics, offering much-needed transparency and interpretability in complex AI models. XAI techniques, such as SHAP, Grad-CAM, and LIME, enable clinicians to understand AI-driven decisions, fostering greater trust and collaboration between human and machine in clinical settings. This review explores the key benefits of XAI in enhancing diagnostic accuracy, personalizing patient care, and ensuring compliance with regulatory standards. However, despite its advantages, XAI faces significant challenges, including balancing model accuracy with interpretability, scaling for real-time clinical use, and mitigating biases inherent in medical data. Ethical concerns, particularly surrounding fairness and accountability, are also discussed in relation to AI's growing role in healthcare. The review emphasizes the importance of developing hybrid models that combine high accuracy with improved interpretability and suggests that future research should focus on explainable-by-design systems, reducing computational costs, and addressing ethical issues. As AI continues to integrate into healthcare, XAI will play an essential role in ensuring that AI systems are transparent, accountable, and aligned with the ethical standards required in clinical practice.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Hepatocellular carcinoma (HCC) is currently the third leading cause of malignancy-related mortalities worldwide. Natural killer (NK) cells are involved in the critical role of first line immunological defense against cancer development. Defects in NK cell functions are recognized as important mechanisms for immune evasion of tumor cells. NK cell function appears to be attenuated in HCC, and many previous reports suggested that NK cells play a critical role in controlling HCC, suggesting that boosting the activity of dysfunctional NK cells can enhance tumor cell killing. However, the detailed mechanisms of NK cell dysfunction in tumor microenvironment of HCC remain largely unknown. A better understanding of the mechanisms of NK cell dysfunction in HCC will help in the NK cell-mediated eradication of cancer cells and prolong patient survival. In this review, we describe the various mechanisms underlying NK cell dysfunction in HCC. Further, we summarize current advances in the approaches to enhance endogenous NK cell function and in adoptive NK cell therapies, to cure this difficult-to-treat cancer.

Trans-arterial radioembolization (TARE) is a form of radiation therapy performed for hepatocellular carcinoma (HCC) via selective intra-arterial injection of Yttrium-90 loaded microspheres. This was a multicenter retrospective study of consecutive patients with HCC who underwent TARE between July 2009 and May 2019. Using pre-treatment computed tomography imaging, the total cross-sectional area (cm2) of the abdominal skeletal muscle at the third lumbar vertebra was measured. The skeletal muscle index (SMI) was calculated by normalizing the muscle area to patient height. In total, 347 patients (median age, 65 years; 284 male) were included in the study. A total of 108 (31.1%) patients had portal vein tumor thrombus (PVTT) and 126 (36.3%) were classified as sarcopenic. The median overall survival (OS) was 28.1 months (95% CI, 24.8-35.7) and median progression-free survival was 8.0 months (95% CI, 6.4-9.4). Multivariate Cox regression analysis revealed that sarcopenia (hazard ratio [HR], 1.36; 95% CI, 1.00-1.85, p = 0.05), PVTT (HR, 1.82; 95% CI, 1.33-2.49, p &lt; 0.01), alpha-fetoprotein (AFP) (≥200 ng/mL) (HR 1.41; 95% CI, 1.04-1.92, p = 0.03), and albumin-bilirubin grade (2-3) (HR 1.74; 95% CI, 1.24-2.43, p &lt; 0.01) were independently associated with poor OS. TARE provided favorable long-term outcomes for patients with advanced HCC. Pre-treatment sarcopenia independently associated with survival, suggesting its utility as a surrogate biomarker for identifying TARE candidates.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

This paper examines the moral community thesis in the secular context of China. Using multilevel logistic regression, we test (1) whether both individual- (measured by affiliation with institutional religion) and aggregate-level religiosity (measured by the number of religious sites per 10,000 people in province) are inversely related to law and rule violations at the individual level and (2) whether the province-level religiosity enhances the inverse relationship between individual religiosity and the deviant behaviors. Results from analyzing data from the 2010 China General Social Survey and the Spatial Explorer of Religions show that both individual- and aggregate-level religiosity are inversely related to the odds of violating the law and various rules of government, transportation, workplace, and other organizations. However, the cross-level interactions are not significant across models, indicating that the contextual religiosity does not increase the effect of individual-level religiosity on deviance. Implications of findings for the moral community thesis are discussed.

Kim(2015) introduced the degenerate Cauchy numbers of the second kind and gave some identities of them. In this paper, by using the modified polyexponential functions which are introduced by Kim-Kim(2019), we define the degenerate poly-Cauchy polynomials of the second kind and investigate some properties of them. Furthermore, we consider the degenerate unipoly-Cauchy polynomials of the second kind and discuss some properties of them.

Objectives: Stress urinary incontinence (SUI) negatively affects the quality of life and sexual function in women. This study aimed to evaluate the efficacy of radiofrequency (RF) therapy in reducing SUI symptoms and its impact on sexual function. Methods: Thirty-four women with SUI were enrolled and underwent a single RF treatment session using the Viveve® System (Viveve Medical Inc., USA) with parameters of 90 J/cm² and 220 pulses per hour. Assessments at baseline and 6 months post-treatment included perineal ultrasound and personal interviews to evaluate lower urinary tract symptoms and sexual function. Urodynamic studies, voiding diaries, and questionnaires such as the Female Sexual Function Index (FSFI), Overactive Bladder Symp-tom Score (OABSS), Urogenital Distress Inventory-6 (UDI-6), Incontinence Impact Question-naire-7 (IIQ-7), and International Consultation on Incontinence Questionnaire-Short Form (ICIQ-SF) measured outcomes. Results: RF therapy significantly improved sexual function, with higher FSFI scores in all domains except pain at 6 months. SUI symptoms were significantly re-duced, as indicated by improved scores on OABSS, UDI-6, IIQ-7, and ICIQ-SF, alongside better voiding diary results. Anatomical changes included reduced bladder neck mobility, decreased vaginal width, and a reduced rotation angle of the proximal urethra. Conclusions: RF therapy is effective and safe for treating mild to moderate SUI and enhances sexual function, potentially due to changes in vaginal topography. These results suggest RF therapy as a viable non-surgical op-tion for managing SUI and improving sexual health.

Various therapeutic approaches have been developed for neglect. Many studies have demonstrated the effect of Digital therapeutics(DTx) on neglect. By contrast, only a few studies have reported on the effects of DTx on egocentric and allocentric neglect. In this article, seven studies on DTx of egocentric and allocentric neglect were reviewed. DTx, which was employed in these studies, could be classified as follows: 1) software adaptation in traditional treatment, 2) VR game using the head-mount display as treatment, and 3) development of new digital program like ReMoVES. In addition, more studies and effective results were reported on egocentric neglect than allocentric neglect. In future studies, each effect on egocentric and allocentric neglect should be identified in detail through the appropriate use of differential evaluation and long-term application of independent digital therapeutics.

In this paper, we study a generalised CIR process with externally-exciting and self-exciting jumps, and focus on the distributional properties and applications of this process and its aggregated process. The first and second moments of this jump-diffusion process are used to calculate the insurance premium based on mean-variance principle. The Laplace transform of the aggregated process is derived, and this leads to an application for pricing default-free bonds which could capture the impacts of both exogenous and endogenous shocks. Illustrative numerical examples and comparisons with other models are also provided.

This paper presents a bibliometric analysis of highly cited papers published in the journal Sustainability between 2009 and 2023. The aim is to identify influential countries, authors, and papers, as well as patterns in authorship and citation trends. The analysis focuses on frequently cited sources, the most cited research papers and references within the journal, and trends in author keywords. The analysis shows that Sustainability is a leading publication in sustainability research, with an annual growth rate of 53.57%. The selected papers, published between 2013 and 2022, have an average age of 2.11 years and an average of 88.12 citations each. The study highlights the most influential countries in sustainability research published in Sustainability, with China leading, followed by the United States and Germany. The most prolific authors are from China, Spain, and Italy. Interdisciplinary collaboration is essential to address complex sustainability challenges, as shown in the papers published in Sustainability. The study emphasizes the importance of staying informed about emerging trends and research directions in the field of sustainability published in this journal Sustainability. It underscores the significance of fostering international collaborations and partnerships to address complex sustainability challenges facing our world today, as evidenced by the papers published in Sustainability. Overall, this bibliometric analysis provides valuable insights into the current state of sustainability research published in Sustainability and its implications for policy and practice. It highlights key areas for future research and underscores the need for interdisciplinary collaboration to address complex sustainability challenges, as demonstrated by the papers published in Sustainability. These findings have important implications for policymakers, researchers, and practitioners interested in promoting sustainable development in the field of sustainability., as published in Sustainability.

Since first described by Dr. Tomisaku Kawasaki in 1967, the clinical diagnosis of Kawasaki disease (KD) has remained relatively unchanged. However, studies since then have suggested that diagnoses using only that original clinical criteria may lead to underdiagnosis. In this review, updated KD diagnostic methods, diagnostic methods for “atypical” KD, diagnostic pitfalls, and other differential diagnoses are discussed. Peripheral blood eosinophil showed important in distinguishing KD from febrile children. We review herein the current literature regarding new biomarkers, scoring systems, and microRNA panels that may aid in the diagnosis of KD, the importance of eosinophil and treatment updates.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

The growing threat of antibiotic pollution in water systems demands innovative and sustainable remediation strategies. Nanocellulose-based magnetic metal-organic frameworks (MOFs) represent a cutting-edge solution for the adsorption and removal of antibiotics, leveraging their high porosity, magnetic properties, and environmentally friendly nature. This paper provides an in-depth review of recent advancements in nanocellulose-based MOFs, focusing on their synthesis, adsorption mechanisms, and applications in environmental remediation between 2020 and 2024. By summarizing key studies, we highlight their performance in targeting widely used antibiotics such as tetracyclines and fluoroquinolones. The integration of nanocellulose with MOFs not only enhances adsorption capacity but also offers easy recovery, recyclability, and environmental compatibility. This review explores their adsorption mechanisms, practical applications, and future research directions, contributing to the advancement of scalable and sustainable water treatment technologies.

The structure characterization of two new polysaccharides from Agrocybe aegerita (AA-P) and Hygrophorus olivaceoalbus (HO-P) by HPGPC, GC-MS, NMR and FT-IR indicated that AA-P was composed of Galactose, Glucose and Arabinose, in the ratio of 3:2:1. Its skeleton structure was consisted of (1→4)-Arap, (1→4,6)-Glup and (1→6)-Galp with one branched chain. The HO-P was consisted of mannose, galactose and glucose in a ratio of 1:1:2. Its skeleton structure was consisted of (1→6)-Galactose residues, (→1)-glucose residues, (1→4)-glucose residues and (1→4,6)-D-mannose residues. There were two branched chains connected to the main chain. AA-P and HO-P had the best stimulation effect on B cells and RAW264.7 cells, respectively, and could both mainly by impacting and reducing G0/G1 phase which lead to a significant proliferation of B cells, T cells and RAW264.7 cells. In addition, AA-P and HO-P could significantly promote the secretion of TNF-α from T cells, the secretion of IgA, IgD, IgE, IgG and IgM from B cells, and the secretion of TNF-α from RAW264.7 cells, but neither of them could impact the secretion of IL-1β from RAW264.7 cells.

The purpose of this study was to detect mind-wandering experienced by pre-service teachers while learning video lecture on physics. The lecture was videotaped and consisted of a live lecture in a classroom. The lecture was about Gauss's law on physics. We investigated whether oculomotor data and eye movements could be used as a marker to indicate the learner’s mind-wandering. Each data was collected in a study in which 24 pre-service teachers (16 females and 8 males) reported self-caught mind-wandering while learning physics video lecture during30 minutes. A Tobii Pro Spectrum (sampling rate: 300Hz) was used to capture their eye-gaze during learning Gauss's law course video. After watching video lecture, we interviewed pre-service teachers about their mind-wandering experience. We first used the self-caught method to capture the mind-wandering timing of pre-service teachers while learning from video lectures. We detected more accurate mind-wandering segments by comparing fixation duration and saccade count. We investigated two types of oculomotor data (blink count, pupil size) and nine eye movements (average peak velocity of saccades; maximum peak velocity of saccades; standard deviation of peak velocity of saccades; average amplitude of saccades; maximum amplitude of saccades; total amplitude of saccades; saccade count/s; fixation duration; fixation dispersion). The result was that the blink count could not be used as a marker for mind-wandering during learning video lectures among them (oculomotor data and eye movements), unlike previous literatures. Based on the results of this study, we identified elements that can be used as mind-wandering markers while learning from video lectures that are similar to real classes, among the oculomotor data and eye movement mentioned in previous literatures. Also, we found that most participants focused on past thoughts and felt unpleasant after experiencing mind-wandering through interview analysis.

This study focused on the development and implementation of an educational simulation program based on Korean Triage and Acuity Scale (KTAS) for nurses in emergency medical centers who completed KTAS training. We also examined its educational effects based on the evaluation of clinical decision-making ability, job satisfaction, and customer orientation. The study participants were 30 nurses in the emergency medical center of a general hospital. Data were collected from May 3 to 24, 2017, and analyzed using SPSS 22.0. There was a significant difference in the mean scores in clinical decision-making ability, job satisfaction, and customer orientation before and after simulation education. In other words, emergency nurses who received KTAS-based simulation education program improved their clinical decision making ability, job satisfaction, and customer orientation. Based on the results of this study, it is expected that it can be used for KTAS education, and it was found that simulation-based education is a useful learning method for triage nurses in emergency medical center.

Owing to their unique physicochemical properties, nanoparticles are used in a variety of ways in the field of cancer treatment, including imaging, drug delivery, and photothermal and photodynamic therapies. The fascinating properties of nanoparticles are determined by their size, morphology, and constituent elements, and various synthetic methods and post-synthetic techniques have been applied to control these factors. Herein, we present examples of shape and composition control through galvanic replacement, a technique that exploits redox potential differences between elements to induce spontaneous ion-exchange and highlight its specific contributions to cancer treatment applications. The present article identifies the recent advances in nanoparticle formation techniques and discusses the future outlook of the field.

This study aimed to identify the utility of diffusion-weighted magnetic resonance (MR) imaging with an apparent diffusion coefficient (ADC) map as a predictor of the intrahepatic response of hepatocellular carcinoma (HCC) to cisplatin-based hepatic arterial infusion chemotherapy (HAIC). We retrospectively evaluated 113 consecutive patients with HCC who underwent gadoxetic acid-enhanced and diffusion-weighted MR imaging. The appropriate cutoff for the tumor-to-liver ADC ratio was determined to be 0.741. Of the 113 patients, 51 (45%) presented with a tumor-to-liver ADC ratio < 0.741. Evaluation of the intrahepatic treatment response after 2-3 cycles of HAIC in these 51 patients revealed that 20 patients (39%) experienced an objective response to HAIC. On the other hand, only 10 of the 62 patients with a tumor-to-liver ADC ratio ≥ 0.741 (16%) experienced an objective response. Thus, the objective response rate was significantly higher in patients with a tumor-to-liver ADC ratio < 0.741 than in those with a tumor-to-liver ADC ratio ≥ 0.741 (P = 0.006). Multivariate logistic regression analysis using parameters including perfusion alteration, percentage of a non-enhancing portion, and tumor-to-liver ADC ratio revealed that a tumor-to-liver ADC ratio < 0.741 (odds ratio 3.03; P = 0.015) is the sole predictor of an objective response to HAIC. Overall survival rates were significantly higher in patients with objective responses to HAIC than in those without objective responses (P = 0.001 by log-rank test). In conclusion, patients with unresectable HCC with a tumor-to-liver ADC ratio < 0.741 showed a favorable intrahepatic response to HAIC. Therefore, diffusion-weighted MR imaging can play a critical role as a predictor of response to cisplatin-based HAIC in unresectable HCC.

Biofilm formation in unicellular eukaryotes, such as Candida albicans and Saccharomyces cerevisiae, represents a significant challenge in various sectors, including healthcare, agriculture, and industry. These biofilms are resistant to conventional antimicrobial treatments due to their protective extracellular matrix and complex regulatory mechanisms, such as quorum sensing (QS) and cyclic AMP (cAMP) signaling. Recent advances in the understanding of biofilm formation pathways have led to the identification of novel compounds that target these regulatory mechanisms. This review highlights breakthroughs from 2024 research, focusing on the inhibition of quorum sensing, disruption of extracellular matrix synthesis, and transcriptional/post-transcriptional regulation of biofilm-related genes. The application of these discoveries in Vietnam is particularly promising, given the country's challenges with biofilm-related infections in healthcare and productivity losses in agriculture and aquaculture. Natural product-based approaches, especially those derived from Vietnam's marine biodiversity, offer environmentally sustainable solutions for biofilm control. However, translating these laboratory findings into scalable, cost-effective applications faces challenges such as resistance development, environmental sustainability, and regulatory constraints. This review provides a comprehensive overview of compounds targeting biofilm regulatory mechanisms, evaluates their potential applications in Vietnam, and discusses future research directions, emphasizing the need for interdisciplinary collaboration to address the complexities of biofilm control.

To identify gender- and age-related associations between adult dental checkups and unmet dental care needs, we analyzed data of 14,000 participants, ages ≥ 19, from the 7th Korea National Health and Nutrition Examination Survey (2016–2018) (KNHANES VII). Data was collected via self-report questionnaires and interviews. Complex sample chi-square test and multiple logistic regression analysis indicated 31.7% of participants had unmet dental care needs; in the prior 12months, 67.1% had not utilized dental services, and 43.3% had not received dental checkups. Odds ratios (ORs) for dental checkups and unmet dental needs were 8.87 (CI:7.80–10.09, p < 0.001) for those who used dental services and 1.28 (CI: 1.13–1.44, p < 0.001) for those who had not. Significant age-dependent associations between those not receiving dental checkups and the rate of unmet dental care include men and women aged 50–59 years (OR: 1.77; CI = 1.22–2.58 and OR: 1.43; CI: 1.02–2.02; p = 0.040, respectively) and women ≥ 70 years (OR = 1.79, CI = 1.20–2.66, p = 0.004). Reducing unmet dental care needs requires greater public health promotion and education regarding regular dental checkups; additional practical strategies could enhance dental checkup compliance.

Pneumococcal disease, caused by Streptococcus pneumoniae is the leading cause of high mortality in children worldwide. The tremendous direct cost of hospital admissions and significant indirect costs from productivity loss contributed considerably to the economic burden, with vaccination being the only efficient way against the illness. Our study aims to summarize the cost-effectiveness of the pneumococcal conjugate vaccine (PCV) implemented in the pediatric population. Employing online databases from Pubmed, Embase, and Medline, we looked for economic evaluation from 2018 until March 2024. The Incremental Cost-Effectiveness Ratios (ICER) and Quality-Adjusted-Life-Years (QALY) were the primary outcomes for measuring PCV's cost-effectiveness. A 28-item CHEERS 2022 checklist was applied to assess the quality of collected studies. Of the 16 papers found, 9/16 discussed the lower-valent vaccine (PCV13, PCV10) and 7/16 examined the higher-valent vaccine. (PCV20, PCV15). PCV13 and PCV10 required more cost and generated more QALY compared to no vaccination. Both PCV15 and PCV20 averted substantial healthcare costs and yielded greater quality of life than PCV13. Additionally, PCV20 was a dominant strategy compared to PCV15. Utilizing PCV13 is a very cost-effective option compared to not getting vaccinated. Transitioning from PCV13 to PCV20 would result in higher QALY gain and more cost-saving than switching to PCV15.

As most Korean OTT subscribers use mobile devices as their primary medium for watching OTT video content, mobile network traffic is soaring. However, the existing build-out of mobile communication technology – such as deploying more base stations or expanding the network bandwidth – is struggling to keep pace with the enormous increased demands of mobile network traffic. Accordingly, wireless device-to-device (D2D) caching networks are considered one of the most reliable alternatives for reducing the overload from mobile network traffic caused by streaming video content online. However, wireless D2D caching networks have pros and cons, like any other technology. Thus, this study aims to examine the practical decision-making process of mobile OTT service users in response to the application of wireless D2D caching networks on their mobile devices. An online survey of 94 respondents was conducted in South Korea during 19–23 May 2022; the data obtained were analyzed using the analytic hierarchy process (AHP) approach. The study finds that it was the risks, rather than the situational conditions and benefits, that mostly affected mobile OTT service users’ behavioral intentions and strategies. Streaming video content using mobile data or Wi-Fi was perceived as the most viable option. Mobile OTT service users were also willing to take the leap of shifts towards downloading video content in advance rather than adopting wireless D2D caching networks on a mobile device. However, mobile OTT service users’ decisions are heavily dependent on situational conditions related to use of mobile OTT services that make the quality of service consumption different. As one of the first to examine the responses of mobile OTT service users, this study provides meaningful implications for a timely and sensitive issue.

The main purpose of this paper is to evaluate electrical treeing degradation for cable insulation. To effectively deal with the currently facing issues, I endeavor to find the most optimal methods by means of applying signal process. First, we made three type models of electrical tree for PD generation to show the distribution characteristics and applied voltage to acquire data by using a PD detecting system. These acquired data presented distribution and four 2D distributions. Hn(q), Hn(), Hqn(), and Hqmax() were derived from the distribution of partial discharge. From the analysis of these distributions, each PD model is proved to hold its unique characteristics and the results were then applied as basic specific qualities for insulation conditions. In order to recognize the progresses of an electrical tree, we proposed methods using scale parameter by means of Weibull distribution. We measured the time of tree propagation for 16 specimens of each model from initiation stage, middle stage, and breakdown respectively, using these breakdown data, we estimated the shape parameter, scale parameter and MTTF(Mean Time To Failure). The results of this study recognize the sources of PD by applying acquired data from PD signals to pre-acquired data. If the cause of PD is degradation, in other words, electrical tree, we can determine the replacement time of devices at the initiation stage of tree growth progress or no later than the middle stage and use it as a basic methods analysis diagnosis system. That is, pattern recognition and Weibull distribution can be employed to get the reliability of diagnosis.

This study aims to identify the factors determining the income of forestry household in South Korea. We examine an empirical analysis using 3-year panel data conducted by the Korea Forest Service charged with maintaining South Korea's forest lands. The hypothesized factors determining the income of forestry household are classified into four types of assets and three types of livelihood strategies. We divided the income of forestry household (IFH) into three elements: forestry income (FI), non-forestry income (NFI), and transfer income (TI). We assessed the influences of household assets and livelihood strategies on each income. A random effect model was used as a statistical analysis with valid 979 of forestry household for three years. We found that household head's age, labor hours, savings, business category, cultivated land size, and region are significantly associated with IFH. Also, FI is influenced by labor capacity, cultivated size, business category, forestry business portfolio, and region while NFI is determined by household head's age, household head's gender, forestry business portfolio, and savings. TI is affected by household head's age, household head's education level, forestry business portfolios, savings, and region. The effect sizes and directions vary across different types of income (IFH, FI, NFI, and TI). The findings show that forestry in South Korea is highly dependent on sustainable assets and strategies. It is therefore expected that the effectiveness of forest policies to increase the income of forestry household would be differed by the source of each income. The results of this study draw attention to the need for an income support policy that should consider the characteristics of household assets and livelihood strategies in order to enhance IFH in South Korea.

Resistive random-access memory has emerged as a promising non-volatile memory technology, garnering substantial attention due to its potential for high operational performance, low power consumption, and scalability. Two-dimensional nanostructured materials play a pivotal role in RRAM devices, offering enhanced electrical properties and physical attributes that contribute to overall device improvement. In this study, self-rectifying switching behavior in RRAM devices is proposed based on molybdenum disulfide nanocomposites decorated with palladium on SiO2/Si substrates. The integration of Pd and MoS2 at the nanoscale effectively mitigates leakage currents decreasing from cross-talk in the RRAM array, eliminating the need for a separate selector device. The successful demonstration of the expected RRAM switching behavior follows the application of a Pd nanoparticle coating. The fabricated Pd-MoS2 synaptic device showed a high current ratio for forward/reverse current higher than 60 at a low resistance state and observed a memory on/off ratio of 103 performing stable resistance switching behavior.

The exponential growth of multimodal content across social media platforms, comprising text, images, audio, and video, has catalyzed substantial interest in artificial intelligence, particularly in multi-modal sentiment analysis (MSA). This study presents a comprehensive survey of 30 research papers published between 2020 and 2024 by eminent publishers such as Elsevier, ACM, IEEE, Springer, and others indexed in Google Scholar. Our analysis primarily focuses on exploring multimodal fusion techniques and features, with specific emphasis on the integration of text and image data. Additionally, the article offers an overview of the evolution, definition, and historical context of MSA. It delves into the current challenges and potential advantages of MSA, investigating recent datasets and sophisticated models. Furthermore, the study provides insights into prospective research directions. Notably, this review offers valuable recommendations for advancing research and developing more robust MSA models, thus serving as a valuable resource for both academic and industry researchers engaged in this burgeoning field.

This paper designs and fabricates a small-type permanent-magnet linear motor and driver for automation applications. It covers structural design, magnetic circuit analysis, control strategies, and hardware development. Magnetic circuit analysis software JMAG is used for flux density distribution, back electromotive force(back-EMF), and electromagnetic force analysis. To address end effects and cogging force, auxiliary core structures and control strategies are proposed. The motor has a three-phase, six-coil, seven-pole configuration, achieving a peak phase voltage of 3.621 V at 1.0 m/s with a total harmonic distortion(THD) of 0.49 % and the voltages of each phase are balancing a phase voltage error of -0.002 V. The average electromagnetic force is 5.46 N/A. The driver uses a three-phase inverter with voltage space vector pulse width modulation(VSVPWM), dq-axes current closed-loop control, electromagnetic force control, and S-curve motion trajectory control. Simulations with JMAG-RT models in MATLAB/Simulink verify the control strategies. A microcontroller (TMS320F280045) serves as the control core, and a magnetic encoder with a 488 nm resolution provides position feedback. Each phase winding has an equivalent resistance of approximately 3.0 Ω and an inductance of approximately 1.98 mH. The S-curve motion trajectory control achieves a maximum position error of approximately 5.0 μm and a speed ripple of approximately 0.03 m/s at steady speed. With cogging force improvement, the maximum electromagnetic force is 4.90 N, and the q-axis current compensates around 1.05 A based on mover position. S-curve motion trajectory control results in highly stable and responsive performance. Practical tests show that the designed small-type permanent-magnet linear motor and its driver provide efficient, stable, and high-precision solutions for automation applications.

Abstract: (1) Background: existing treatment methods for neglect are concentrated on egocentric neglect and lead to various problems, such as cost/space constraints and portability. Therefore, this study seeks to determine how treatment (a.k.a., Twins Therapy, TT) can improve an existing problem in relation to neglect in stroke patients; (2) Method: The research design was a pre-post test control group design and both groups maintained existing rehabilitation treatment and added TT intervention only to the experimental group. TT intervention was conducted for a total of 20 sessions (1 session 30 min/day, 5 days/week for 4 weeks); (3) Result: as a result of comparison be-fore and after the TT intervention, there was no significant difference in MFT and MBI items (p>.05). However, the score and execution time of the Apple Cancellation Test showed significant reduction only in the experimental group (p<.05); (4) Conclusion: as a result of the study, TT im-proved not only egocentric neglect, but also allocentric neglect symptoms in stroke patients

Most research findings in Ghana and all over the globe lay much emphasis on the technical knowledge of plastics; especially giving preference to the biodegradable over the synthetic/Single-Use plastics. Questionnaires were administered to about 200 respondents in the Ho Municipality out of which 163 responses were filled and returned. Results showed that of all the variables tested only Legislative Framework has a meaningful impact on the behaviour of Ho indigenes. Awareness level: (Synthetic Plastics and Biodegradable Plastics) as well as Attitudinal Change do not influence people’s behaviour when using plastics. Findings from this study are further discussed and recommendations were proffered to instil eco-friendly behaviour among people.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Marine vessels operating on the Arctic Sea route are constantly prone to collisions and friction with ice. This study discusses the wear of the hull plate caused by the collision of ice against vessels operating in Arctic Sea routes. The abrasive wear of the hull due to ice impact was numerically assessed based on both the incident behavior of ice particles interacting with the flow around the hull and the wear loss of the hull surface caused by the contact force of ice particles. A multi-phase approach was adopted to account for the behavior of ice particles continuously affected by the fluid force around the hull. The fluid force acting on the ice floe was evaluated using computational fluid dynamics (CFD) and the dynamic motion of the drift ice was evaluated using the discrete element method (DEM). The motion of the floating ice particles was updated in real time by iteratively coupling the fluid force and the motion of the ice floe at each time step of the numerical simulation. The results of the wear simulation models were presented in terms of the shape change of the hull surface due to wear. At first, the wear was evaluated for cases in which only the surface paint of the hull was damaged. Thereafter, a computation model considering the shape change of the hull surface experiencing long-term friction of ice particles was introduced. Finally, the numerical procedures to predict the abrasive wear of the hull surface by ice impact were discussed.

Medical institutions, where several patients are treated and medical workers engaged, are always exposed to secondary viral and bacterial infections. It is critical to prevent infection transmission by indirect as well as direct contact through air or splash. The infections of most diseases can be transmitted through the air. HEPA filters installed in air conditioning equipment are used to prevent infection transmission through air in medical institutions, but air circulation takes a long time in a large space. Virus and bacteria smaller than 0.3 μm cannot be removed by the HEPA filter; hence, those microbes remain alive throughout the air ventilation. A plasma sterilizer has the capability to provide environmental friendly sterilization by employing reactive oxide species and reactive nitrogen species at a low cost. We developed an excellent plasma sterilizer by using a non-thermal atmospheric-pressure biocompatible plasma (NBP). Ozone concentration in plasma sources has been derived by Kuhn et al. [1]. The diffusion coefficients inside (D₀) and outside (D₁) the plasma sterilizer have been calculated to be 0.0641 m² s^-1 and 0.717 m² s^-1, respectively. To sustain high O₃ concentrations over 121 ppm inside the plasma source and low O₃ concentrations below 0.05 ppm outside the sterilizer, it is necessary to keep O₃ concentrations at the exit of plasma sterilizer below 0.28 ppm. so that diffusion coefficient D₁ has been designed to be as large as 11 times of D₀.

The continuing development of industrialization and increasing population density has led to the emergence of noise as an increasingly common problem, requiring various types of sound absorption and insulation methods to address it. Meanwhile, the recycling of resources to ensure a sustainable future for the planet and mankind is also required. Therefore, this study investigates the potential of corrugated cardboard as a resource for noise reduction. The sound absorption and insulation performance of non-perforated corrugated cardboard (NPCC) were measured, and modified corrugated boards were fabricated by drilling holes either through the surface of the corrugated board alone or through the corrugated board in its entirety. The sound absorption/insulation performance both of perforated corrugated cardboard (PCC), and perforated corrugated cardboard with multi frequency resonators (PCCM) were measured using the transfer function method and the transmission matrix method. To determine the effectiveness of NPCC, PCC, and PCCM in noise reduction, the sound pressure level was analyzed by applying it to a home blender. The results showed PCCM’s sound absorption and insulation performance to be excellent. On the basis of these findings, we propose the use of PMMC as an eco-friendly noise reduction material.

The purpose of this study is to identify the different effects exerted by planting density and nitrogen fertilization on high-salinity Reclaimed Paddy Fields(RPF) and General Paddy Fields(GPF), and to find the amount of fertilization and the planting density suitable for the growth of forage rice in each paddy field. In both experimental locations, there was no significant change in the soil due to N treatment, but in the case of RPF, electrical conductivity(EC) decreased significantly from more than 5dS/m to up to 2.87dS/m during the yellow ripe stage due to the influence of floods and concentrated precipitation on the fields. In all soils, as both the amount of N treatment and the planting density increased, there was a proportional relationship in which the number of tillers and the dry weight also increased, with the occurrence of lodging also being increased. The dry weight, as expected, was 1.5 times higher at a planting distance of 10 cm, rather than 16 cm. In addition, in both locations N treatment led to an increase in the dry weight, but when N treatment reached 400kg/ha (2.0), the dry weight decreased instead. Moreover, although there was no clear difference in feed value according to N treatment, in RPF, neutral detergent fiber(NDF) was higher than 60%, RFV was less than 98, and TDN was also low, confirming that the quality of rice was higher in GPF.

This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

Background and objectives: TSC1 is a crucial component of the mTOR pathway, impacting cell growth, proliferation, and autophagy, while TSC2 is a tumor suppressor gene that regulates cell growth and is associated with the mTOR signaling pathway. In the present study, we analyzed TSC1 and TSC2 mRNA expression levels in rectal cancer, and evaluated the clinicopathological and prognostic characteristics of TSC1 and TSC2. Materials and Methods: TSC1 and TSC2 mRNA expression was examined in various cancer types. We further evaluated survival to determine the prognostic significance of TSC1 and TSC2 mRNA in CRC using The Cancer Genome Atlas (TCGA) data. Results: The study focused on rectal cancer, as it exhibited the most promising results. The patients were split into two subgroups, each comprising 50% of the total, based on the TSC gene expression levels. This division was made to assess the clinical characteristics associated with the expression of TSC1 and TSC2 genes. In the study, lower TSC1 expression was linked to venous invasion in rectal cancer patients, and there was also a related trend with lymphatic invasion, although it didn't reach statistical significance. Lower TSC2 expression was observed in younger patients and had some associations with sex and M stage, but these correlations were not statistically significant. When it came to survival analysis, TSC1 expression did not significantly impact overall survival, while higher TSC2 expression was associated with a poorer prognosis in rectal cancer. To enhance our comprehension, additional research, especially in larger case studies, is needed to explore the molecular mechanisms and clinical characteristics of TSC genes in colorectal cancer.

The present study was conducted to evaluate encapsulated essential oils as an alternative anticoccidial in coccidiosis vaccine challenged broiler chickens. A total of 600 day-old male broiler chicks were provided with no-added corn-soybean meal-based control diet or diets that contained either salinomycin or EO at 60 and 120 mg per kg of diet. On day 21, half of the control groups were orally challenged with a coccidiosis vaccine at 25 times higher than the recommended vaccine dose. During 22 to 28 days (i.e., one-week post coccidiosis vaccine challenge), the challenged chickens had decrease (P < 0.05) in body weight gain and feed intake but increase in feed conversion ratio compared with the non-challenged, naïve control chickens. However, dietary EO significantly counteracted (P < 0.05) coccidiosis vaccine-induced depression in body weight gain and feed intake. Increasing dietary EO linearly decreased (P < 0.05) the concentrations of the volatile fatty acids. Dietary SAL and EO affected gut morphology in chickens at 20 days posthatch. Increasing dietary EO linearly (P = 0.073) increased serum catalase activity. Collectively, our study shows that dietary EO increased coccidiosis vaccine-induced growth depression and altered gut physiology in broiler chickens.

Radiator reliability is crucial in environments characterized by high temperatures and friction, where prompt interventions are often required to prevent system failures. This study introduces a proactive approach to radiator fault diagnosis, leveraging the integration of Gaussian Mixture Model (GMM) and Long-Short Term Memory (LSTM) autoencoders. Vibration signals from radiators were systematically collected through randomized durability vibration bench tests, resulting in four operating states—two normal, one unknown, and one faulty. Time-domain statistical features of these signals were extracted and subjected to Principal Component Analysis (PCA) to facilitate efficient data interpretation. Subsequently, this study discusses the comparative effectiveness of GMM and LSTM in fault detection. GMMs are deployed for initial fault classification, leveraging their clustering capabilities, while LSTM autoencoders excel in capturing time-dependent sequences, facilitating advanced anomaly detection for previously unencountered faults. This alignment offers a potent and adaptable solution for radiator fault diagnosis, particularly in challenging high-temperature or high-friction environments. Consequently, the proposed methodology not only provides a robust framework for early-stage fault diagnosis but also effectively balances diagnostic capabilities during operation. Additionally, this study presents the foundation for advancing reliability life assessment in accelerated life testing, achieved through dynamic threshold adjustments using both the absolute log-likelihood distribution of the GMM and the reconstruction error distribution of the LSTM autoencoder model.

This paper examines the relationship between the ratio of independent board member to the financial performance of the company under the mediation of the three pillars of environment, society, and governance (ESG) in Taiwan. The study addresses a research gap between independent directors and corporate financial performance, an issue that is rarely discussed today. The author develops the hypotheses and tests them by applying panel data regression to the data tables taken from the Thomson Reuters Eikon database to analyze data on 173 Taiwanese companies that reported ESG from 2009 to 2021. The results show that the relationship between the ratio of independent directors and financial performance has a positive relationship. At the same time, the 3 pillars of ESG also clearly show the intermediary role in this relationship. Finally, this study provides additional insights into the relationship between the ratio of independent directors and financial performance in the Taiwan context.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Very poor oral health, common among older adults, is associated with cognitive decline.This study aimed to investigate the association between denture use, chewing ability, and cognitive function in Korean middle-aged adults using samples representing middle-aged people at the national level. This longitudinal study included 9,998 middle-aged adults via Korea Longitudinal Study of Aging 7th special survey data. Denture use, chewing ability, health-related factors, and general characteristics were assessed by the Computer Assisted Personal Interview. After controlling general characteristics using a generalized estimating equation model, the association of denture use and MMSE scores with chewing ability of those with or without dentures and MMSE scores were analysed. Twenty-four percent of participants wore dentures among them, 35.1% complained of difficulty chewing when wearing dentures. Among participants who did not wear dentures, 16.4% complained of difficulty chewing. MMSE scores were lower among denture-wearers than non-denture wearers (β = -0.026, p < 0.001). In both groups, MMSE scores decreased with chewing difficulty and were significantly reduced among non-denture wearers (p < 0.05). Chewing ability was closely associated with cognitive function. Given the negative effect of difficulty chewing on cognitive function, maintaining chewing ability should be of great concern.

Several studies in computer vision have examined specular removal, which is crucial for object detection and recognition. This research has traditionally been divided into two tasks: specular highlight removal, which focuses on removing specular highlights on object surfaces, and reflection removal, which deals with specular reflections occurring on glass surfaces. In reality, however, both types of specular effects often coexist, making it a fundamental challenge that has not been adequately addressed. Recognizing the necessity of integrating specular components handled in both tasks, we constructed a Specular-Light (S-Light) DB for training single-image-based deep learning models. Moreover, considering the absence of benchmark datasets for quantitative evaluation, the Multi-Scale Normalized Cross Correlation (MS-NCC) metric, which considers the correlation between specular and diffuse components, was introduced to assess the learning outcomes.

Recently, two respiratory syncytial virus (RSV) vaccines based on the prefusion F (pre-F) antigen were approved in the United States. We developed and validated an enzyme-linked immunosorbent assay (ELISA)-based protocol for the practical and large-scale evaluation of RSV vaccines. Two modified pre-F proteins (DS-Cav1 and SC-TM) were produced by genetic recombination and replication using an adenoviral vector. The protocol was established by optimizing the concentrations of the coating antigen (pre-F proteins), secondary antibodies, and choice of blocking buffer. To validate the protocol, we examined its accuracy, precision, and specificity using serum samples from 150 participants across various age groups and the standard serum provided by the National Institute of Health. In the linear correlation analysis, coating concentrations of 5 and 2.5 μg/mL of DS-Cav1 and SC-TM, respectively, showed high coefficients of determination (r2 = 0.90). Concentrations of secondary antibodies (alkaline phosphatase-conjugated anti-human immunoglobulin G, diluted 1:2000) and blocking reagents (5% skim milk/PBS-T) were optimized to minimize non-specific reactions. High accuracy was observed for DS-Cav1 (r2 = 0.90) and SC-TM (r2 = 0.86). Further, both antigens showed high precision (coefficient of variation &lt; 15%). Inhibition ELISA revealed cross-reactivity of antibodies against DS-Cav1 and SC-TM but not with the attachment protein.

This study is the first to investigate the asymmetric effects of oil price volatility on stock returns for the Ho Chi Minh Stock Exchange (HOSE). We utilized weekly series of VN30-Index, WTI crude oil prices, geopolitical risks (GPR) index and gold prices spanning from 6 February 2012 to 31 December 2023 as data sources. Using a nonlinear Autoregressive Distributed Lag (NARDL) bounds testing approach, we found that in the short-term, oil price volatility has negative asymmetric effects on the market returns. Specifically, in the short-term, a one percent increase in oil price volatility immediately leads to a 2,6868 percent decrease in the market returns while a similar magnitude decrease in oil price volatility is associated with 6.3180 percent increase in the market returns. In addition, the results obtained from the NARDL model indicated that, in the long-term, the negative and positive changes of oil price volatility have significantly negative effects on the market returns. Finally, the findings derived from the error correction model (ECM) show that 98.21 percent of the disequilibria from the previous week are converged and corrected back to the long-term equilibrium in the current week.

Rotorcrafts operate HUMS for fault diagnosis, but the capabilities of HUMS analysts are important due to the complex mechanical configuration of rotorcraft and the difficulty of analysis. Accordingly, an advanced algorithm is needed to identify faults, and flight data can be used to develop the algorithm. However, flight data contains abnormal or missing data due to problems such as sensor defects, which can be a major problem in algorithm development. Therefore, in this paper, we study a gap filling method using MLP to obtain normal data when there are problems such as abnormal or missing data in rotorcraft flight data. Existing methods typically fill the gap through interpolation or curve fitting using the before and after values of missing data. However, in this study, normal values were estimated using the values of other parameters at the moment of missing or abnormal data occurred. As a result of evaluating the performance of the trained MLP using normal data, it was confirmed that the output of the model well estimates the changing trend of the target. And when abnormal data was applied to the trained model, it was confirmed that point outliers were eliminated and appropriate values were found in the case of missing data.

Although global life expectancy has increased over the past 20 years due to improvements in managing infectious diseases, one in five people still succumbs to infections. Humanity is tirelessly working towards developing vaccines and antimicrobial agents in response to this ongoing threat. However, pathogens continue to acquire numerous resistance mechanisms and proliferate. Meanwhile, the COVID-19 pandemic has prompted us to recognize that focusing solely on the killing strategies of immunology and microbiology in complex and multisystemic infectious diseases is insufficient for understanding survival. In essence, there is a need for a treatment approach centered on disease tolerance, capable of alleviating pathology and/or promoting physiological functions in conjunction with the existing strategies of host immune response and pathogen destruction. Against this backdrop, this narrative review comprehends and introduces microbiome therapeutics, which recently garnered attention as next-generation treatments regarding two defense strategies against infectious diseases. First, we delineate the application of existing probiotics and then the microbiome in infectious diseases. Subsequently, we expand this concept to encompass host microbiome crosstalk and present related microbiome therapeutics' current status and direction. Ultimately, the review presents a fresh perspective on understanding microbiome therapeutics in infectious diseases based on a cooperative defense system.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

Robot-assisted gait training (RAGT) is a promising treatment for stroke rehabilitation. Although the coordination between the upper and lower limbs is important for locomotor training, commercially available robotics for gait training mainly focus on the restoration of lower limb function. We aimed to evaluate the feasibility and usability of complex upper and lower limb RAGT in stroke patients using the GTR-A®, end effector-type robotic device. Patients with subacute stroke (N=9) received 30-minute RAGT thrice a week for two weeks (six sessions). Functionally, the hand grip strength (HGS), Functional Ambulatory Categories, modified Barthel Index, muscle strength test sum score, Berg Balance Scale, Timed Up and Go test, and Short Physical Performance Battery were used. The heart rate and a structured questionnaire were used to evaluate cardiorespiratory fitness and the usability of RAGT. Among the nine patients, all functional parameters between the baseline and post-training were significantly improved after RAGT, except for HGS and the muscle strength test. The questionnaire’s mean scores for each domain were as follows: safety 4.40±0.35, effects 4.23±0.31, efficiency 4.22±0.77, and satisfaction 4.41±0.25. The GTR-A® is a feasible and safe robotic device for patients with gait impairment after stroke. It showed functional improvement with endurance training effects.

In this paper, we introduce the partially degenerate Changhee-Genocchi polynomials and numbers and investigated some identities of these polynomials. Furthermore, we investigate some explicit identities and properties of the partially degenerate Changhee-Genocchi arising from the nonlinear dierential equations.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

The growing population meet the challenge for agricultural production. CRISPR/Cas9 technology is based on plant research for the development of the new varieties as well as disease resistance crops. In addition the deletion of significant characters makes the new alleles from the CRISPR/Cas9. Recent and reliable molecular scissor for genetic engineering. The review is focused on the various application of the CRISPR/Cas9 technology in plant enhancement of plant disease resistance, stress burden in plant, nutritional improvement, and quality of crops from the CRISPR/Cas9 system. The clustered regularly interspaced short palindromic repeat (CRISPR)-associated protein9 (cas9) is adopted from the prokaryotic type II system. CRISPR/Cas9 is simplicity and efficiency than ZENs and TALENs for the genome engineering. Due to rapid growing of the CRISPR/Cas9 system has been formulate the adaptation of many plant species. The current advancement of plants and future schemes of improve of CRISPR technology has been presented in contest of multiplex editing, knowledge on induced mutation whether the factor effect in CRISPR/Cas9 technology in plant. Remarkable perspective and challenges of CRISPR/Cas9 technology in significance of plant genetic modification.