In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation as that expressed in terms of total motions where the base shear force is applied for earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91.

The sensitivity of DNBR(Departure from Nucleate Boiling Ratio) values to approaches of subchannel control volume selection has been investigated for the TS01 and TS03 out of HIPER17 CHF(Critical Heat Flux) tests. In general, the coolant-centered subchannel method is applied to subchanel analyses for fuel bundle. When it comes to predicting for CHF of high quality region, however, the rod-centered subchannel method was better over high quality region. As a result, the rod-centered subchannel method were more suitable at a conservative point of view than the coolant-centered subchannel method comparing major properties. Also, it was confirmed that the radial subchannel locations at the minimum DNBR were similar when comparing both analysis results by two kind of methods.

This study aims to investigate the effects of chest mobilization and breathing exercises on respiratory function, trunk stability, and endurance in chronic stroke patients who have contracted coronavirus disease (COVID-19). Thirty inpatients of a tertiary hospital in South Korea, who had a history of COVID-19 and were diagnosed with stroke within the last 6 months were randomly assigned to either the Chest Mobilization Exercise with Breathing Exercise (CMEBE) or Conservative Physical Therapy with Breathing Exercise (CPTBE) groups. The respiratory function, trunk stability, and endurance were measured at baseline and 6 weeks after the interventions. Both CMEBE and CPTBE groups showed improvements in respiratory function, trunk stability, and endurance after the intervention (p<0.05). However, the CMEBE group showed significantly greater improvements in forced expiratory volume in 1 second (p<0.05), trunk stability (p<0.05), and endurance (p<0.05) than the CPTBE group. No significant intergroup difference was observed in forced vital capacity and peak expiratory flow. Conclusion: The combination of chest mobilization and breathing exercises improved respiratory muscle mobility and endurance, stabilized the trunk, and enhanced balance and transfer of weight. The findings suggest that this intervention could be beneficial in improving respiratory function and endurance in stroke patients.

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

For the elimination of radio-frequency interference (RFI) in a passive microwave radiometer, the threshold level is generally calculated from the mean value and standard deviation. However, a serious problem that can arise is an error in the retrieved brightness temperature from a higher threshold level owing to the presence of RFI. In this paper, we propose a method to detect and mitigate RFI contamination using the threshold level from statistical criteria based on a spectrogram technique. Mean and skewness spectrograms are created from a brightness temperature spectrogram by shifting the 2-D window to discriminate the form of the symmetric distribution as a natural thermal emission signal. From the remaining bins of the mean spectrogram eliminated by RFI-flagged bins in the skewness spectrogram for data captured at 0.1-s intervals, two distribution sides are identically created from the left side of the distribution by changing the standard position of the distribution. Simultaneously, kurtosis calculations from these bins for each symmetric distribution are repeatedly performed to determine the retrieved brightness temperature corresponding to the closest kurtosis value of three. The performance is evaluated using experimental data, and the error in the retrieved brightness temperature is observed to be less than approximately 3 K from a window with a size of 100 × 100 time-frequency bins according to the RFI levels and cases.

Background and Objectives: Although there has been growing interest in the association of ADHD with anxiety, depression, suicidal ideation, and self-esteem, there is a lack of consistent results and these associations remain unclear. This study investigated the differential patterns of anxiety, depression, suicidal ideation, and self-esteem with regard to the presence of ADHD. Materials and Methods: The subjects were divided into a patient group and a control group. The patient group included 49 patients diagnosed with ADHD at the department of psychiatry of one university hospital. For the control group, 3,727 students were invited to complete a questionnaire. Of the 1,717 students who responded to the questionnaire, 245 were selected for patient-controlled studies. All the subjects were instructed to complete the Beck Suicide Ideation Scale, Children's Depression Inventory, Beck’s Depression Inventory, State-Trait Anxiety Inventory, and Rosenberg Self-Esteem Scale. Results: ADHD subjects experienced more anxiety, depression, and suicidal ideation as well as lower self-esteem compared to the control group comprising participants without ADHD. Conclusions: These findings suggest that ADHD symptoms may contribute to greater suicidal ideation through experienced depression, anxiety, and low self-esteem in school-aged children. Therefore, appropriate ADHD symptom management is necessary to reduce suicidal ideation among school-aged children with ADHD symptoms.

Mobile elevating work platforms (MEWPs) consist of a work platform, extending structure, and chassis, and are used to move persons to working positions. MEWPs are useful but are composed of pieces of equipment, and accidents do occur owing to equipment defects. Among these defects, accidents caused by the fracture of bolts fixed to the extension structure and swing system are increasing. This paper presents a failure analysis of the fixing bolts of MEWP. Standard procedure for failure analysis was employed in this investigation. Visual inspection, chemical analysis, tensile strength measurement, and finite element analysis (FEA) were used to analyze the failure of the fixing bolts. Using this failure analysis approach, we found the root cause of failure and proposed a means for solving this type of failure in the future. First, the chemical composition of the fixing bolt is obtained by a spectroscopy chemical analysis method, which determined that the chemical composition matched the required standard. The tensile test showed that the tensile and yield strengths were within the required capacity. The stress analysis was carried out at five different boom angles, and it was determined that the fixing bolt of MEWP can withstand the loads at all the boom angles. The outcomes of the fatigue analysis revealed that the fixing bolt fails before reaching the design requirements. The results of the fatigue analysis showed primarily that the failure of the fixing bolt was due to fatigue. A visual inspection of the fractured section of the fixing bolt also confirmed the fatigue failure. We propose a method to prevent failure of the fixing bolt of the MEWP from four different standpoints: the manufacturer, safety certification authority, safety inspection agency, and owner.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

This work investigates the stability conditions for linear systems with time-varying delays via augmented Lyapunov-Krasovskii functional(LKF). Two types of augmented LKFs with cross terms in integral are suggested to improve the stability conditions for interval time-varying linear systems. Through this work, the compositions of the LKFs are considered to enhance the feasible region of stability criterion for linear systems. Mathematical tools such as Wirtinger-based integral inequality(WBII), zero equalities, reciprocally convex approach, and Finsler’s lemma are utilized to solve the problem of stability criteria. Two sufficient conditions are derived to guarantee the asymptotic stability of the systems using linear matrix inequality(LMI). First, asymptotic stability criteria are induced by constructing the new augmented LKFs in Theorem 1. And then simplified LKFs in Corollary 1 are proposed to show the effectiveness of Theorem 1. Second, asymmetric LKFs are shown to reduce the conservatism and the number of decision variables in Theorem 2. Finally, the advantages of the proposed criteria are verified by comparing maximum delay bounds in two examples. Two numerical examples show that the proposed Theorem 1 and 2 obtained less conservative results than existing outcomes. Also, Example 2 shows that the asymmetric LKF methods of Theorem 2 can provide larger delay bounds and fewer decision variables than Theorem 1’s in some specific systems.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

The phenolics concentrations of rapeseed are important because they are antinutritional com-pound or directly positive related to antioxidant actives. In this study, single nucleotide poly-morphisms (SNPs) identified from genotyping-by-sequencing (GBS), and genome-wide associa-tion study of phenolic contents were investigated in 95 rapeseed mutant lines derived from gamma rays and their original cultivar. A total of 3,196,318 SNPs were detected, identifying a set of 70,208 union SNPs used to perform association studies. Six phenolics and glucosinolate (pro-goitrin) were identified, sinapine was the major phenolic compound (91.2–99.2%) in all geno-types. The association study was conducted for six phenolic compounds, progoitrin, total sinap-ine content (TSC), total phenolic content (TPC) and seed yield. The association study identified 241 SNPs that were significantly associated with six phenolic compounds, progoitrin, TSC and TPC. Based on the detected SNP markers, BnaA06g31740D, a gene associated progoitrin, BnaC-nng39930D, a gene associated trans-sinapine 1, BnaA07g31720D, a gene associated trans-sinapine 2, BnaC03g31950D and BnaA06g09180D, a gene associated TSC, and BnaAnng27700D, a gene associ-ated TPC, were selected as candidate genes. The SNP makers associated major phenolic com-pounds identified and could be used as targets for breeding programs aimed at improving anti-oxidant contents and reducing antinutritional components.

Toward the standardization of O. biennis sprout extract (OBS-E), we aimed to obtain indicator compounds, using a validated method. HPLC-UVD allowed simultaneous quantification of indicator compounds quercetin 3-glucuronide and ellagic acid. The method was validated in terms of specificity, linearity, precision, accuracy, and limit of detection/limit of quantification (LOD/LOQ). High specificity and linearity was demonstrated, with correlation coefficients of 1.0000 for quercetin 3-glucuronide and 0.9998 for ellagic acid. The LOD/LOQ values were 0.486/1.472 μg/mL for quercetin 3-glucuronide and 1.003/3.039 μg/mL for ellagic acid. Intra-day and inter-day variability tests produced relative standard deviation for each compound of &lt;2%, a generally accepted precision criterion. High recovery rate were also obtained, indicating accuracy validation. The OBS-E prepared using various concentrations of ethanol were then analyzed. The 50% ethanol extract had highest content of quercetin 3-glucuronide, whereas the 70% ethanol extract possessed the lowest. However, the ellagic acid content was highest in the 70% ethanol extract and lowest in the 90% ethanol extract. Thus, quercetin 3-glucuronide and ellagic acid can be used industrially as indicator compounds for O. biennis sprout products, and our validated method can be used to establish indicator compounds for other natural products.

Fresh-cut apple is commonly known as minimally processed agriculture products because of their convenience and ease of consumption. However, during storage, the quality of the apple rapidly changes after the cutting process due to enzymatic and non-enzymatic processes. This study aimed to monitor the quality changes of fresh-cut apples at various temperatures and different types of products in the application of a cold chain system during distribution and storage. The results showed that the total viable count in fresh-cut apples initially differed between apple only and mixed products (apple, orange, and tomato) during storage (p &lt; 0.05). Moreover, there are no significant differences (p &gt; 0.05) in physicochemicals except firmness, titratable acidity, and pH, which are highly correlated to microbial growth (total viable count and total coliform number). Furthermore, the optimal temperature for extending the shelf-life of fresh-cut apples was at 4°C.

A Micro holes in a diamond are presented by using a homemade femtosecond (fs) Yb:KGW laser. An fs laser source was used emitting pulse duration of 230 fs at 1030 nm wavelength, whereas the spot size amounted to 8.9 μm. Parameters like pulse energy, and pulse number were varied over a wide range in order to evaluate their influence both on the micro hole geometry like hole diameter, circularity, taper angle, and on the drilling quality. Hourglass-shaped micro holes whose diameters decrease and increase again after a certain depth have important applications. The results demonstrate the feasibility of extending the drilling of an hourglass-shaped hole in a diamond sample, which has similar diameters at the hole entrance (92 μm) and exit (95 μm), but a much smaller diameter (28 μm) at a certain waist section inside the hole.

The National Agrobiodiversity Center under the Rural Development Administration (RDA) in Jeonju, Republic of Korea, is the largest international genebank of Korea. The National Agrobi-odiversity Center has continuously been making efforts to introduce overseas genetic resources to its collection and has currently grown into a world-class PGR holding genebank. Currently, several steps are undertaken to, improve the accessibility of the collection to national as well as international researchers, improve data available on the resources and amend the passport in-formation of the accessions. With the implementation of the Nagoya Protocol, the origin of ge-netic resources is being highlighted as an important input in the passport information of germplasms. The RDA-Genebank actively responds to the Nagoya Protocol by supplementing passport data of resources lacking information on the origin of germplasm. In addition, a large number of conserved resources are continuously multiplied, and agronomic traits are investi-gated concurrently. With the traditional methods of characterization of the germplasm requiring a significant amount of time and effort, we have intiated high-throughput phenotyping using digital techniques to improve our germplasm data. Primarily, we have started adding seed phenotype information followed by measuring root phenotypes which are stored under agro-nomic traits. This may be the initial step for a germplasm center to use large-scale high-throughput techniques for their collection. In this shortcommunication, we aim to provide an introduction to the RDA- Genebank, adopted international standards, and establishment of high throughput phenotyping techniques for improvement of passport information.

The aim of this study was to analyze glucosinolates (GSLs) in germplasms that are currently conserved at the RDA-Genebank. The analysis focused on the glucosinolate diversity among the analyzed germplasms, with the goal of identifying those that would be most useful for future breeding efforts to produce nutritionally rich Choy sum plants..Twenty-three accessions of Choy sum which possessed ample background passport information were selected. By analyzing the glucosinolate content for 17 different glucosinolates, we observed aliphatic GSLs to be the most common. We identified one accession, IT228140 to synthesize high quantities of glucobrassi-canapin and progoitrin which have been reported to contain several therapeutic applications. Overall, this study highlights the importance of conserving and analyzing plant genetic re-sources, such as those held in national genebanks, for the purpose of developing new varieties of crops that are both nutritious and beneficial for human health. The identification of excellent germplasms for breeding material and the confirmation of the anticancer effects of glucosin-olates are significant contributions to the field of agricultural research and have the potential to positively impact public health.

In this paper, we define new kind of Daehee numbers, the degenerate Daehee numbers of the third kind, using degenerate log function as generating function. We obtain some identities for the degenerate Daehee numbers of the third kind associated with the Daehee, degenerate Daehee and degenerate Daehee numbers of the second kind. In addition, we derive a differential equation associated with the degenerate log function. We deduce some identities from the differential equation.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

Sea fog event over the Eastern Yellow Sea on 15–16 April 2012 was reproduced in the Weather Research and Forecasting (WRF) simulation with high-resolution to investigate the roles of phys-ical processes and synoptic-scale flows on advection fog with sea surface warming. Initially, longwave radiative cooling (LRC) with negative sensible heat flux (SHF) due to the turbulence af-ter sunset triggered a formation of cloud at the surface under the moist advection with a southerly wind. This is a conventional type of advection fog. At night, continuous cooling due to longwave radiation and SHF near the surface modulated the change of the SHF from negative to positive, resulting in a drastic increase in the latent heat flux (LHF) that provided sufficient moisture at lower atmosphere (self-moistening). This is a favorable condition for advection fog with sea sur-face heating (ssH), and this transition represents advection fog with ssH. Enhanced turbulent mixing driven by a buoyancy force increased the depth of the sea fog with a gradual rise in the marine atmospheric boundary layer (MABL) height, even at nighttime. In addition, cold advec-tion with a prevailing northerly wind at the top of the MABL led to a drastic increase in turbulent mixing and the MABL height, which resulted in rapid growth of the height of sea fog due to ver-tical diffusion. After sunrise, shortwave radiative warming in the fog layers offsetting the LRC near the surface weakened thermal instability, which contributed to the reduction in the MABL height, even during the daytime. In addition, dry advection of northerly wind induced dissipa-tion of the fog via evaporation. An additional sensitivity test of sea surface salinity showed weaker and shallower sea fog than the control due to the decrease in both the LHF and local self-moistening.

Background A mycotic aortic aneurysm is a rare type of aortic aneurysm that can cause serious and adverse outcomes. Most mycotic aneurysms originate from infectious sources, such as trauma, vegetation in the heart, and adjacent infectious sources. If a mycotic aneurysm is diagnosed, it should be treated simultaneously with the primary source of the infection. Case Report A 63-year-old male presented to the emergency room with a fever, the primary source of which had not been confirmed, and had not responded to antibiotic treatment for two weeks. Treatment was initiated for a mycotic aneurysm of the brachial artery that occurred suddenly while undergoing treatment for the fever. Further investigation revealed that a mycotic aneurysm of the brachial artery was the cause of the fever, followed by aneurysms in the abdomen and lower extremities, and even vegetation on the heart that was not initially present. The patient declined to undergo treatment for personal reasons. After five months, a contained rupture of the abdominal aortic aneurysm that was initially considered as normal aorta was diagnosed and was treated successfully. Conclusions A peripheral mycotic aneurysm may be associated with multiple aneurysms. Appropriate diagnosis and complete management are necessary to prevent fatal consequences.

A surgical microscope is large in size, which makes it impossible to be portable. The distance between the surgical microscope and the observation tissue is 15–30 cm, and the adjustment range of the right and left of the camera is a maximum of 30°. Therefore, the surgical microscope is generated attenuation (above 58%) of irradiation optical source owing to the long working distance. Moreover, the observation of tissue is affected because of dazzling by ambient light as the optical source power is strong (55 to 160 mW/cm2). Further, observation blind spot phenomena will occur due to the limitations in adjusting the right and left of the camera. Therefore, it is difficult to clearly observe the tumor. In this study, a compact pen-type probe with a portable surgical microscope is presented. The proposed surgical microscope comprises a small and portable pen-type probe that can adjust the working distance between the probe and the observed tissue. In addition, it allows the adjustment of the viewing angle and fluorescence brightness. The proposed probe has no blind spots or optical density loss.

A surgical microscope is large in size, making portability impossible. The distance between the surgical microscope and the observation tissue is 15 to 30 cm, while the maximum adjustment range of the camera to the right and left is 30°. Therefore, surgical microscopes cause attenuation (above 58%) of the irradiation optical source owing to the long working distance. Moreover, the observation of tissue was dazzled with ambient light because the optical power source was strong (50 to 160 mW/cm2). Owing to the limited ability to adjust the camera to the right and left, a blind spot occurs with a surgical microscope. Therefore, it is difficult to clearly observe a tumor. In this study, a compact pen-type probe with a portable surgical microscope is proposed. The pen-type probe is small with a portable shape, and is capable of adjusting the working distance between itself and the observed tissue. It is also possible to adjust the viewing angle and fluorescence brightness. The proposed pen-type probe has no blind spots or optical density loss.

Blockchain is the consensus-based technology to resolve the conflicts in Byzantine environments. Vehicles validate the messages received from the neighboring vehicles using Gradient Boosting Technique (GBT). Based on the validation results the message source vehicle generates the ratings that are to be uploaded to Road Side Units (RSUs) through that trust offset value can be calculated. All RSUs maintain the trust blockchain and each RSU tries to add their blocks to trust blockchain. We proposed a blockchain-based trust management model for VANET based on Tendermint. It eliminates the problem of malicious nodes entering the network and will also overcome the problem of power consumption. Simulation results also show that the proposed system is 7.8% and 15.6% effective and efficient in terms of Packet Delivery Ratio (PDR) and End-to-End Delay (EED) respectively to collect the trusted data between the vehicles.

For the effective utilization of rice husk, organosolv fractionation was investigated to separate three main components (glucan, xylose, and lignin) with low acid concentration. Reaction temperatures of 170–190 °C, ethanol concentrations of 50–70% (v/v), and sulfuric acid concentrations of 0–0.7% (w/v) were investigated, with the reaction time and liquid-to-solid ratio kept constant at 60 min and 10, respectively. The fractionation conditions for the efficient separation into the three components of rice husk were determined to be 180 °C, 60% (v/v) of ethanol, and 0.25% (w/v) of sulfuric acid. Under these fractionation conditions, 86.8% of the xylan and 77.5% of the lignin were removed from the rice husk, and xylose and lignin were obtained from the liquid in 67.6% and 49.8% yields, respectively. The glucan digestibility of the fractionated rice husk was 85.2% with an enzyme loading of 15 FPU (filter paper unit) of cellulase per g-glucan.

FMD is a highly contagious animal disease that occurs in cloven-hoofed animals including pigs. To prevent FMD, vaccines and adjuvants are used to induce an immune response, but it is not sufficient to show the effect of preventing viral infection. In this study, we conducted to evaluate the increasing effect of FMD vaccine SP antibody by administrating Zn-ASP to 100 pigs from three test pig farms with feed. FMD vaccine antibody titer and immunological index were analyzed using an enzyme-linked immunosorbent assay (ELISA) kit, and hematological and blood biochemical parameters were analyzed using an automatic blood analyzer. The titer of FMD vaccine SP antibody in the 0.2% Zn-ASP-administered group significantly increased compared to that in the positive control group only injected with FMD vaccine at 4 weeks after the first vaccination and at 4, 8 and 16 weeks after the second vaccination, respectively (p&lt;0.05). The FMD vaccine SP antibody positive rate was 100% until shipment. IFN-γ and IgA were significantly increased by Zn-ASP administration 4 weeks after the first vaccination and 4 weeks after the second vaccination (p&lt;0.05). On the other hand, serum AST, and CPK (p&lt;0.001) were significantly decreased by Zn-ASP. Our results show that the administration of Zn-ASP is effective in enhancing the antibody titer and immunity of the FMD vaccine by FMD vaccination, and it is thought that it can be used as an oral adjuvant (OrAd) to prevent viral diseases such as FMD.

Though melatonin is known to improve ultraviolet B (UVB)-induced oxidative damage and inflammatory conditions via blockade of nuclear factor (NF)-κB, interleukin (IL)-6, there is no report on anti-wrinkle effect of melatonin to date. Hence in the present study, anti-wrinkle mechanism of melatonin was elucidated in UVB treated HaCaT keratinocytes and hairless mice. Herein melatonin protected against a radical initiator tert-Butyl hydroperoxide (t-BOOH) induced reactive oxygen species (ROS) production, matrix metalloprotease 1 (MMP-1) and cytotoxicity in HaCaT keratinocytes. Also, melatonin suppressed the expression of sonic hedgehog (SHH) and GLI for hedgehog signaling, p-NF-kB, cyclooxygenase (COX-2), p-ERK for inflammatory responses in UVB treated HaCaT keratinocytes. Furthermore, melatonin protected skin from wrinkle formation, transdermal water loss in hairless mice irradiated by UVB for 8 weeks. Notably, melatonin prevented against epidermal thickness and dermal collagen degradation in UVB irradiated hairless mice by Hematoxylin & Eosin and Masson’s trichrome staining. Taken together, these findings suggest that melatonin reduces wrinkle formation via inhibition of ROS/SHH and inflammatory proteins such as NF-kB/COX-2/ERK/MMP1.

Lectins, characterized by their carbohydrate-binding ability, have an extensive practical application. However, their industrial use is limited by low yields, and few active recombinant lectins have been reported. In this study, the algal lectin BPL-3 (Bryopsis plumosa lectin 3) was successfully produced using a bacterial expression system, BL21(DE3), with an artificial repeated structure (dimeric construct). Recombinant dimeric BPL3 (rD2BPL3) was confirmed by LC-MS/MS spectrometry. Expression efficiency was greater for the construct with the repeat structure (rD2BPL3) than the monomeric form (rD1BPL3). Optimal conditions for expression were 1 mM IPTG at 20 °C. Recombinant lectin was purified under denaturing conditions and refolded by the flash dilution method. Recombinant BPL3 was solubilized in 1× PBS containing 2 M urea. rD2BPL3 showed strong hemagglutination activity using human erythrocytes, similar to that of native BPL3. rD2BPL3 had a similar sugar specificity to that of the native protein, i.e., to N-acetyl-glucosamine (GlcNAc) and N-acetyl-galactosamine (GalNAc). Glycan array results showed that recombinant BPL3 and native BPL3 exhibited different binding properties. Both showed weak binding activity to α-Man-Sp. Native BPL3 showed strong binding specificity to the alpha conformation of amino sugars, and rD2BPL3 had binding activity to the beta conformation. The process developed in this study was suitable for the quality-controlled production of high amounts of soluble recombinant lectins.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

We simulated the glass-blowing process to model a shell resonator, which is a key component in MRIG (Micro Rate Integrating Gyroscope), using the finite elements method to solve a non-isothermal problem. We also calculated the mechanical characteristics of the modeled resonator, including effective mass, eigenfrequencies, angular gain, and energy loss, to predict the resonator's performance as a gyroscope. One key aspect we addressed is the bending of the resonator's rim toward the stem during glass-blowing process. This phenomenon occurs due to increased heat loss at the mold's edge and reduced heat flux at the side of the Gaussian heat source. To mitigate rim bending and the subsequent reduction in capacitance between the rim and 3D electrodes, which can degrade performance in micro glass-blown shell resonators for gyroscopes, we propose two potential mold solutions. The first is using a short-stem mold, which requires extensive polishing to eliminate the bent rim. The second solution is using a mold with a suitable chamfer at the edge, resulting in a straight rim. To quantitatively compare resonators created by these two types of molds, we calculated the noise factor for predicting its gyroscope performance. From these calculations, we find out that using the chamfered mold enables us to increase in the resonator's effective mass, eigenfrequency, angular gain, and quality factor, consequently reducing the noise factor compared to using the short-stem mold. This simulation process will assist us in getting insight into understanding a shell resonator as a gyroscope, designing a mold and determining experimental conditions.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

The number of fishers working on commercial fishing vessels worldwide is approximately 159,800 according to the Food and Agriculture Organization of the United Nations. The International Labour Organization estimates that the mean annual number of deaths during fishing is approximately 24,000. Most guidelines for the prevention of marine accidents have been developed with a focus on vessels involved in international navigation. As these guidelines may have parts that are unsuitable for application in small-scale boats operating in coastal areas, appropriate modifications are required. This study analyzed quantitative data on 1,790 marine accidents that occurred in trap fishery, a globally common type of fishery, and data obtained through a survey of 101 fishers in South Korea. A guideline to reduce the rate of fatal accidents was developed using the Bayesian network, a method used for the analysis of accidents, as suggested in the formal safety assessment protocol. The results of data analysis and the developed guidelines are expected to be beneficial to all fishers involved in trap fishery across many countries worldwide.

Software-based ultrasound imaging systems provide high flexibility that allows easy and fast adoption of newly developed algorithms. However, the extremely high data rate required for data transfer from sensors (e.g., transducers) to the ultrasound imaging systems is a major bottleneck in the software-based architecture, especially in the context of real-time imaging. To overcome this limitation, in this paper, we present a Binary cLuster (BL) code, which yields an improved compression ratio compared to the exponential Golomb code. Owing to the real-time encoding/decoding features without overheads, the universal code is a good solution to reduce the data transfer rate for software-based ultrasound imaging. The performance of the proposed method was evaluated using in vitro and in vivo data sets. It was demonstrated that the BL-beta code has a good stable lossless compression performance of 20 ~ 30% while requiring no auxiliary memory or storage.

In urban areas, deep excavation-induced ground deformation may damage adjacent existing structures and is conventionally evaluated by levelling at installed settlement points. However, a small number of measurements cannot represent the total change in ground deformation adjacent to excavation sites. Furthermore, significant local subsidence may occur in places where settlement points have not been installed and only noticed after an accident. For deep excavation sites located in urban areas, paved pedestrian sidewalks are often located adjacent to sites, and construction activity can cause these paving blocks to displace. This study introduces a method to detect paving block displacement adjacent to deep excavation sites using terrestrial photogrammetry. A digital camera creating point cloud data (PCD) and an acquisition method satisfying the frontal and side overlap requirements were demonstrated. To investigate the displacement detection and measurement capabilities by PCD analysis, an experimental program was conducted, including a PCD comparison containing the uplift, settlement, and horizontal paving block displacement and reference data. The cloud-to-cloud distance computation algorithm was adopted for PCD comparison. Paving block displacement was detected for displacements of 5, 7.5, and 10 mm in the uplift, settlement, and horizontal directions; however, the horizontal displacements were less clear. PCD analysis enabled satisfactory measurements between 0.024 and 0.881 mm for the vertical-displacement cases, but a significant error was observed for the horizontal-displacement cases owing to the cloud-comparison algorithm. The measurement blind spot of limited settlement points was overcome by the proposed method that detected and measured paving block displacement adjacent to excavation sites.

Eight compounds were isolated from the roots of Glycyrrhiza uralensis and tested for cholinesterase (ChE) and monoamine oxidase (MAO) inhibitory activities. Glycyrol (GC) effectively inhibited butyrylcholinesterase (BChE) and acetylcholinesterase (AChE) with IC50 values of 7.22 and 14.77 µM, respectively, and also moderately inhibited MAO-B (29.48 µM). Six of the other seven compounds only weakly inhibited AChE and BChE, whereas liquiritin apioside moderately inhibited AChE (IC50 = 36.68 µM). Liquiritigenin (LG) potently inhibited MAO-B (IC50 = 0.098 µM) and MAO-A (IC50 = 0.27 µM), and liquiritin, a glycoside of LG, weakly inhibited MAO-B (&gt; 40 µM). GC was a reversible, noncompetitive inhibitor of BChE with a Ki value of 4.47 µM, and LG was a reversible competitive inhibitor of MAO-B with a Ki value of 0.024 µM. Docking simulations showed that the binding affinity of GC for BChE (-7.8 kcal/mol) was greater than its affinity for AChE (-7.1 kcal/mol), and suggested that GC interacted with BChE at Thr284 and Val288 by hydrogen bonds (distances: 2.42 and 1.92 Å, respectively) beyond the ligand binding site of BChE, but that GC did not form hydrogen bond with AChE. The binding affinity of LG for MAO-B (-8.8 kcal/mol) was greater than its affinity for MAO-A (-7.9 kcal/mol). These findings suggest GC and LG should be considered promising compounds for the treatment of Alzheimer’s disease with multi-targeting activities.

Neurofibromatosis type 2 (NF2) is a genetic syndrome characterized by the growth of benign tumors in the nervous system, particularly bilateral vestibular schwannomas, meningiomas, and ependymomas. This review consolidates the current knowledge on NF2 syndrome, emphasizing the molecular pathology associated with the mutations in the gene of the same name, the NF2 gene, and the subsequent dysfunction of its product, the Merlin protein. Merlin, a tumor suppressor, integrates multiple signaling pathways that regulate cell contact, proliferation, and motility, thereby influencing tumor growth. The loss of Merlin disrupts these pathways, leading to tumorigenesis. We discuss the roles of another two proteins potentially associated with NF2-deficiency as well as Merlin: Yes-associated protein 1 (YAP), which may promote tumor growth, and Raf kinase inhibitory protein (RKIP), which appears to suppress tumor development. Additionally, this review discusses the efficacy of various treatments, such as molecular therapies that target specific pathways or inhibit neomorphic protein-protein interaction caused by NF2-deficiency. This overview not only expands on the fundamental understanding of NF2 pathophysiology but also explores the potential of novel therapeutic targets that affect the clinical approach to NF2 syndrome.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

The object of this study was to discover an alternative therapeutic agent with fewer side effects against acne vulgaris, which is one of the most common skin diseases. Acne vulgaris often associates with acne-related bacteria such as <i>Propionibacterium acnes</i>, <i>Staphylococcus epidermidis</i>, <i>Staphylococcus aureus</i> and <i>Pseudomonas aeruginosa</i>, some of which exhibit a resistant against commercial antibiotics used in the treatment of acne vulgaris (tetracycline, erythromycin, and lincomycin). In the current study, we evaluated <i>in vitro</i> antibacterial activity of chitosan-phytochemical conjugates against acne-related bacteria. Three of chitosan-phytochemical conjugates used in this study showed stronger antibacterial activity than that of chitosan (unmodified control). Chitosan-caffeic acid conjugate (CCA) exhibited the highest antibacterial activity against acne-related bacteria with minimum inhibitory concentration values of 8 μg/mL to 256 μg/mL. In addition, the MICs of antibiotics against antibiotic resistant <i>P. acnes</i> and <i>P. aeruginosa</i> strains were dramatically reduced in the combination with CCA, suggesting that CCA would restore the antibacterial activity of the antibiotics. The analysis of fractional inhibitory concentration indices clearly revealed a synergistic antibacterial effect between CCA and the antibiotics. Thus, the median ∑FIC values against the antibiotic resistant bacterial strains were ranged from 0.375 to 0.533 in the combination mode of CCA and antibiotics.

Background The Delta Neutrophil Index (DNI), a prodiagnostic marker for sepsis, utilizes leukocyte count. Platelet activation, similar to leukocytes, plays a crucial role in host defence against pathogens and may serve as a predictor of sepsis outcome. However, the combined evaluation of Mean Platelet Component (MPC) and DNI in assessing sepsis has been rarely used. Methods To assess the prodiagnostic validity of simultaneous utilization of DNI and MPC in cases of human febrile sepsis, we conducted measurements of cellular indices, including DNI and MPC, as well as molecular biomarkers such as procalcitonin (PCT) and C-reactive protein (CRP). This study was carried out on patients admitted to the emergency department with suspected sepsis. Results Using a cutoff value of 2.65%, the sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of DNI in sepsis were found to be 69%, 73.9%, 77.9%, and 64.1%, respectively. Furthermore, significant differences in DNI and MPC levels were observed between the sepsis and non-sepsis groups (6.7±7.8% versus 2.1±2.2%, P=0.000 and 26.0±1.9 g/dl versus 26.8±1.4 g/dl, P=0.002), respectively. Notably, there was a negative correlation between DNI and MPC, with the strength of the correlation varying based on the cause of sepsis. By setting the cutoff value for DNI at 6.2%, the sensitivity, specificity, and NPV improved to 100%, 80.3%, and 100%, respectively, although the PPV remained at 10.6%. Importantly, the DNI≥6.2 group exhibited a higher incidence of death (10.9%, 5/46) and multiorgan failure (19.6%, 9/46) compared to the DNI<6.2 group (0.0%, 0/46 and 0.0%, 0/167, respectively) (P=0.000 and P=0.000, respectively). Conclusions In our study, DNI demonstrates superior effectiveness compared to other molecular biomarkers such as CRP and procalcitonin in distinguishing febrile septic patients from febrile nonseptic patients and predicting prognosis. Additionally, there exists a negative correlation between MPC and DNI, making MPC a valuable marker for differentiating the etiology of sepsis. These findings hold significant clinical implications as DNI/MPC is a cost-effective and readily applicable approach in various impending sepsis scenarios. Notably, this study represents the first examination of the prodiagnostic validity of simultaneously employing DNI and MPC in human cases of febrile sepsis.

Roses are one of the most important floricultural crops, and their essential oils have long been used for cosmetics and aromatherapy. We investigated the volatile compound compositions of 12 flower-color mutant variants and their original cultivars. Twelve rose mutant genotypes were developed by treatment with 70 Gy of 60Co gamma irradiation of six commercial rose cultivars. Essential oils from the flowers of the 18 genotypes were analyzed by gas chromatography–mass spectrometry. Seventy-seven volatile compounds were detected, which were categorized into five classes: hydrocarbons, terpenoids, alcohols, esters, and others. Hydrocarbons, alcohols, and esters were major components in all rose flowers. The mutant genotypes CR-S8 and CR-S9 showed higher contents of hydrocarbons than the original cultivar. In addition, CR-S1, CR-S3, and CR-S4 mutant genotypes showed higher ester contents than their original cultivar. Nonacosane, 2-methylhexacosane, and 2-methyltricosane were major volatile compounds among all genotypes. Hierarchical cluster analysis of the rose genotypes gave four groups according to grouping among the 77 volatile compounds. These findings will be useful for the selection of rose genotypes with improved volatile compounds.

Abstract: Global ecological concern regarding the transfer of fouling organisms to ship hulls is increasing. This study investigated the species composition, dominant species, distribution patterns, community structure, and life-cycle differences of hull-fouling macroinvertebrates on five research vessels (R/Vs: Isabu, Onnuri, Eardo, Jangmok 1, and Jangmok 2) operated by the Korea Institute of Ocean Science and Technology (KIOST). Hull-fouling macroinvertebrates were collected three to five times on quadrats from the upper and middle sectors of the hull sides, bottom, and niche areas (the propellers and shafts and the thrusters). A total of 47 macroinvertebrate species were identified, represented by 8,519 individuals(ind.)/m2 and a biomass of 1,967 gWWt/m2 on the five vessels. The number of species, density, and biomass were greater on the coastal vessels the Eardo, Jangmok 1, and Jangmok 2 than on the ocean-going vessels the Isabu and Onnuri. Among the coastal vessels, barnacles were the most abundant and had the greatest density, while mollusks had the highest biomass. Differences between hull sectors showed that the highest species abundance and density appeared on all hulls in ports and bays where the Jangmok 1 operated, while the highest species abundance, density, and biomass were identified in the niche areas of the Eardo, which operated farther from the coast. The hull-fouling macroinvertebrates that exceeded 1% of all organisms were the barnacles Amphibalanus amphitrite, Balanus trigonus, and Amphibalanus improvisus; the polychaete Hydroides ezoensis; the bivalves Magallana gigas and Mytilus galloprovincialis; and the amphipod Jassa slatteryi. The dominant species were cosmopolitan and globally distributed, and many of them were cryptogenic. Six native species were identified: M. gigas, H. ezoensis, the amphipod Melita koreana, the isopod Cirolana ko-reana, and the barnacle B. trigonus and F. kondakovi. Eight non-indigenous species (NIS) were de-tected: barnacles A. amphitrite and A. improvisus, the bivalve M. galloprovincialis, the polychaete Perinereis nuntia, amphipods J. slatteryi and Caprella californica, and bryozoans Bugulina californica and Bugula neritina. Of the fouling macroinvertebrates found on the vessel hulls, 13% were native and 17% were NIS. The nMDS ordination analysis of the five vessels showed four clusters of fouling macroinvertebrate communities: two ocean clusters (the Isabu and Onnuri), one coastal cluster (the Eardo and Jangmok 2), and one local cluster (the Jangmok 1). More diverse communities developed on the hulls of vessels that operated locally rather than globally or in deep oceans. Spearman rank correlation showed that biological indices such as number of species, density, and biomass correlated highly and positively with the numbers of days on coastal operations and negatively with the number days on ocean operations. The species diversity index correlated positively with the total number of anchoring days and coastal operation days and negatively with the total number of operation days and ocean operation days. The macroinvertebrates differed by the area of operation, the port of anchorage, the number of days in operation and at anchor, and the hull sectors. There is no previous research data on hull-fouling macroinvertebrates in the Republic of Korea, and this study provides a basis for future studies to identify introduced species and their differences based on operation area.

Krill oil (KO) shows promise as a natural marine-derived ingredient for improving skin health. This study investigated its antioxidant, anti-inflammatory, anti-wrinkle, and moisturizing effects on skin cells and UVB-induced skin photoaging in hairless mice. In vitro assays on HDF, HaCaT, and B16/F10 cells, and in vivo experiments on 66 hairless mice, were conducted. Mice received oral KO administration (100, 200, or 400 mg/kg) once a day for 15 weeks and UVB radiation three times a week. In vitro, KO significantly countered UVB-induced oxidative stress, reduced wrinkles, and prevented skin water loss by enhancing collagen and hyaluronic synthesis. In vivo, all KO dosages showed dose-dependent inhibition of oxidative stress-induced inflammatory photoaging-related skin changes. Skin mRNA expressions for hyaluronan synthesis and collagen synthesis genes also increased dose-dependently after KO treatment. Histopathological analysis confirmed that Krill Oil (KO) ameliorated the damage caused by UVB-irradiated skin tissues. These findings suggest that KO may be a valuable intervention to mitigate UVB-induced skin photoaging and address various skin concerns.

Space-based Interferometric Synthetic Aperture Radar (InSAR) applications have been widely used to monitor the cryosphere over past decades. Because of temporal decorrelation, interferometric coherence often severely degrades on fast moving glaciers. In addition, higher sensitivity ambiguity occurs in large baseline configurations, which are needed for extracting topographic information over low relief areas such as the surface of a glacier. TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) observations, which overcome the temporal decorrelation because of their simultaneous measurements by two satellite constellations, have used a short baseline sufficient for generation of excellent digital elevation models in most locations around the world. However, it remains difficult to estimate detailed topographic characteristics over low slope glacier surfaces because of the relatively less sensitive height ambiguity from the small baselines. In this study, we used the TanDEM-X pursuit monostatic mode with large baseline formation following a scientific phase timeline to develop highly sensitive topographic elevation models of the Petermann Glacier of Northwest Greenland. As expected, coherent interferometric phases (> 0.8) were well maintained over the glaciers despite their fast movement thanks to the nearly simultaneous TanDEM‐X measurements. The height ambiguity, which defined as the altitude difference correspondent to phase change of flattened interferogram, of the dataset was 10.63 m, which is favorable for extracting topography in a low relief region. We validated the TanDEM‐X derived glacial topography by comparing it to the SAR/Interferometric radar altimeter observations acquired by CryoSat‐2 and the IceBridge Airborne Topographic Mapper laser altimeter measurements. Both observations showed very good correlation within a few meters of the offsets (‐12.5 – ‐3.1 m) with respect to the derived glacial topography. Because of highly sensitive ambiguity, we could successfully extract detailed geomorphological features on the glaciers. Routine TanDEM-X observations will be very useful to better understand the dynamics of glacial movements and topographic change.

In this paper, feasibility of the initial alignment of the gyro-free inertial navigation system (GF-INS) is investigated. Initial roll and initial pitch are obtained as the conventional INS since centripetal acceleration is very small. Relation between initial heading and accelerometers’ outputs of the gyro-free inertial measurement unit (GF-IMU) is derived. It is determined from the relation whether initial heading can be obtained in 15 GF-IMUs which have been presented in research literatures. The relationship between the accelerometer errors of GF-IMU and the initial heading error is derived. When gyros are additionally attached in one axis or two axes of the body frame, it is investigated that initial heading can be obtained. The initial heading error is also calculated from the accelerometer errors and the gyroscope errors. The results show that the initial heading from only accelerometer outputs of the GF-IMU cannot be used in the GF-INS since the error is too large. It can also be seen from the results that the initial heading can be used in the GF-INS if two gyroscopes are additionally attached to the roll and pitch axes of the body frame.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Stem cells derived from dental tissues—dental stem cells—are flavored due to their easy acquisition. Among them, dental pulp stem cells (DPSCs) extracted from the dental pulp have many advantages such as high proliferation and highly purified population. Although their ability for neurogenic differentiation has been highlighted and neurogenic differentiation using electrospun nanofibers (NFs) has been performed, graphene-incorporated NFs have never been applied for DPSC neurogenic differentiation. Here reduced graphene oxide (RGO)-polycaprolactone (PCL) hybrid electrospun NFs were developed and applied for enhanced neurogenesis of DPSCs. First, RGO-PCL NFs were fabricated by electrospinning with incorporation of RGO and alignments, and their chemical and morphological characteristics were evaluated. Furthermore, in vitro NF properties such as influence on the cellular alignments and cell viability of DPSCs were also analyzed. The influences of NFs on DPSCs neurogenesis was also analyzed. The results confirmed that an appropriate concentration of RGO promoted better DPSC neurogenesis. Furthermore, the use of random NFs facilitated contiguous junctions of differentiated cells, whereas the use of aligned NFs facilitated aligned junction of differentiated cells along the direction of NF alignments. Our findings showed that RGO-PCL NFs can be a useful tool for DPSC neurogenesis, which will help regeneration in neurodegenerative and neurodefective diseases.

Purpose: Therapeutic targeting of RAF1 is promising, but it requires further investigation for the relation between clinical features and RAF1 aberrations regarding the MAPK signaling pathway in various solid tumors to realize the precision medicine. Methods: Between October 2019 and June 2023, Samsung Medical Center, 3,895 patients with metastatic cancer patients received a next-generation sequencing (NGS) using TruSight Oncology 500 (TSO500) assay as a routine clinical practice. We surveyed the incidence of RAF1 aberration including mutation (single-nucleotide variant [SNV]), amplification (copy-number variation), and fusion. Results: In 3,895 metastatic cancer patients, 77 (2.0%) had RAF1 aberrations in their tumor specimen. Of 77 patients, 44 (1.1%) had RAF1 mutations (SNV), 25 (0.6%) had RAF1 amplification and 10 (0.3%) had RAF1 fusions. Among 10 patients with RAF1 fusion, concurrent RAF1 amplification and RAF1 mutation were detected in one patient each. The most common tumor types were bladder cancer (11.5%), followed by ampulla of Vater (AoV) cancer (5.3%), melanoma (3.0%), gallbladder (GB) cancer (2.6%), and gastric cancer (2.3%). Microsatellite instability high (MSI-H) tumors were found in 5 out of 76 patients (6.6%) with RAF1 aberration, while MSI-H tumors were found only in 2.1% of patients with wild-type RAF1 cancer (p < 0.0001). Conclusion: We showed that when patients with metastatic solid cancer receive NGS test, approximately 2.0% have RAF1 aberrations in their tumor specimen.

The global shrimp farming industry is impacted by various infectious diseases, leading to marked production losses. Virulent Vibrio parahaemolyticus strains (VPAHPND) and other Vibrio species cause acute hepatopancreatic necrosis disease (AHPND) in shrimp. We isolated a binary toxin PirA/B-bearing V. campbellii strain (HJ-2023) from a Korean shrimp farm. The biochemical characteristics and antibiotic susceptibility of HJ-2023 were analyzed and compared to those of PirA/B-bearing VPAHPND. Non-AHPND-causing V. campbellii was the control. The pathogenicity of each strain was analyzed in white-leg shrimp. Phylogenetic analysis classified the isolated HJ-2023 strain as V. campbellii. Biochemical tests confirmed distinct properties of HJ-2023, compared to the genetically similar V. harveyi group. The AHPND-causing toxin gene of HJ-2023 showed 100% similarity to the rpoD gene of VCAHPND. An antibiotic disc susceptibility test indicated that HJ-2023 showed resistance to ampicillin, clindamycin, lincomycin, and erythromycin, which is effective against gram-positive bacteria, and showed weak sensitivity to gentamycin. Furthermore, HJ-2023 was 25% less toxic than VPAHPND but could be lethal during aquaculture-related outbreaks. These results highlight the complexity and virulence of AHPND-causing strains through multiple pathways and confirm the pathogenicity of V. campbellii, which increases the risk posed by AHPND to shrimp aquaculture. Our findings could help prevent AHPND.

Hf1-xZrxO2 (HZO) thin films are versatile materials suitable for advanced ferroelectric semiconductor devices. Previous studies have shown that the ferroelectricity of HZO thin films, can be stabilized by doping them with group III elements at low concentrations. While doping with Y improves the ferroelectric properties, there has been limited research on Y-HZO thin films fabricated using atomic layer deposition (ALD). In this study, we investigated the effects of Y doping cycles on the ferroelectric and electrical properties of as-deposited Y-HZO thin films with vaying compositions fabricated through ALD. The Y-HZO thin films were stably crystallized without the need for post-thermal treatment and exhibited transition behavior depending on the Y-doping cycle and initial composition ratio of the HZO thin films. These Y-HZO thin films offer several advantages, including enhanced dielectric constant, leakage current density, and improved endurance. Moreover, the optimized Y-doping cycle induced a phase transformation that resulted in Y-HZO thin films with improved ferroelectric properties, exhibiting stable behavior without fatigue for up to 1010 cycles. These as-deposited Y-HZO thin films show promise for applications in semiconductor devices that require high ferroelectric properties, excellent electrical properties, and reliable performance with a low thermal budget.

Coronary artery disease (CAD) is a prevalent cardiovascular condition characterized by the accumulation of plaque within coronary arteries. This plaque accumulation obstructs blood flow to the heart, resulting in a heart attack. While distinct features of CAD have been identified, its causes remain largely unclear, with the exception of environmental and nutritional factors. This study aimed to investigate the connection between genetic factors and CAD, focusing on the thymidylate synthase (TS) gene, a gene involved in one-carbon metabolism. Therefore, our research targeted single nucleotide polymorphisms that could potentially impact TS gene expression and lead to dysfunction. Our findings strongly associate the TS 1100T&gt;C and 1170A&gt;G genotypes with CAD susceptibility. We observed that TS 1100T&gt;C polymorphisms increased disease susceptibility in several groups, while the TS 1170A&gt;G polymorphism displayed a decreasing trend for disease risk when interacting with clinical factors. Furthermore, our results demonstrate the potential contribution of the TS 1100/1170 haplotypes to disease susceptibility, indicating a synergistic interaction with clinical factors in disease occurrence. Based on these findings, we propose that polymorphisms in the 3'-UTR miRNA binding site of the TS gene could serve as clinically useful biomarkers for the prevention, prognosis, and management of CAD.

We report the use of four-layer graphene (4LG) as a highly reliable transparent conductive electrode (TCE) for polymer-dispersed liquid crystal (PDLC)-based smart window devices. The adhesion between 4LG and the substrate was successfully improved through a water-induced interface-cleaning (WIIC) process. We compared the performance of a device with a WIIC-processed 4LG electrode with that of devices with a conventional Indium tin oxide (ITO) electrode and a 4LG electrode without a WIIC. With the application of the WIIC process, the PDLC smart window with a 4LG electrode exhibited reduced turn-on voltage and haze compared to 4LG without the WIIC process and characteristics comparable to those of the ITO electrode. Based on our observations, we conclude that 4LG with WIIC is a promising TCE for flexible smart windows.

We investigated the efficacy of a Rumex crispus and Cordyceps sinensis mixture made using the Beopje (Korea traditional processing method to remove anti-nutrients and enhance phytochemicals) method to regulate immune cell responses toward nitric oxide (NO) production, pro-inflammatory cytokines, and inflammation related genes in mice splenocytes. The six experimental groups were as follows: control (control), Rc-Cs (Rumex crispus (Rc) and Cordyceps sinensis (Cs) mixture, 6:4), TMC (Taemyeongcheong, commercial healthy drink containing Rc-Cs), LPS (lipopolysaccharide), LPS+Rc-Cs, and LPS+TMC. The Rc-Cs mixture reduced nitric oxide (NO) production in LPS-induced splenocytes. Moreover, Rc-Cs enhanced production of the pro-inflammatory cytokines TNF-α, IFN-γ, IL-1β, and IL-6 compared to the control (no treatment). However, Rc-Cs inhibited production of pro-inflammatory cytokines in LPS-induced splenocytes. In addition, LPS+Rc-Cs also significantly suppressed mRNA expression of IL-1β and IL-6 compared to LPS treatment. Interestingly, Rc-Cs did not increase mRNA levels of iNOS and COX-2, which are inflammation related genes compared to the control, while LPS+Rc-Cs reduced mRNA levels of iNOS and COX-2 compared LPS alone (p < 0.05). TMC showed a similar pattern compared to Rc-Cs. Therefore, Rc-Cs treatment in splenocytes enhanced NO production and pro-inflammatory cytokines compared to the control, whereas Rc-Cs treatment in LPS-induced splenocytes reduced NO production, pro-inflammatory cytokines, and inflammation related genes. Thus, Rc-Cs regulated immune cells responses by increasing pro-inflammatory cytokines in splenocytes and reducing toxin (LPS)-induced inflammation. These results indicate that a Rumex crispus and Cordyceps sinensis mixture (Rc-Cs) and TMC containing Rc-Cs promote immune cells responses and anti-inflammatory activities.

Ras homolog enriched in brain (Rheb1 and Rheb2), a small GTPase, regulates neuronal activity and has drawn attention for its implications in cancer development, especially breast cancer. This study explores the multifaceted role of Rheb1 in cancer, elucidating its involvement in crucial cel-lular processes such as proliferation, apoptosis resistance, migration, invasion, metastasis, and inflammatory responses. Despite these acknowledged connections, a comprehensive understanding of the intricate interplay between Rheb1 and cancer remains elusive. This review consolidates cur-rent knowledge on the impact of Rheb1 on cancer hallmarks and examines the potential of Rheb1 as a therapeutic target in cancer treatment. The review underscores the need for a more profound comprehension of the molecular mechanisms underlying Rheb1-mediated oncogenic processes. Furthermore, the review emphasizes the exploration of Rheb1 inhibitors as a promising avenue for cancer therapy. This study, by bringing to light the complex associations between Rheb1/Rheb2 and cancer, delivers valuable insights to the scientific community. These insights are instrumental in guiding the identification of novel targets and advancing the development of effective therapeu-tic strategies for treating cancer.

This study was conducted to determine whether overcrowding in the emergency department (ED) affects the occurrence of a return visit (RV) within 72 hours. The crowding indicator of index visit was the average number of total patients, patients under observation, and boarding patients during the first 1 and 4 hours from ED arrival time and the last 1 hour before ED departure. Logistic regression analysis was conducted to determine whether each indicator affects the occurrence of RV and post-RV admission. Of the 87,360 discharged patients, 3,743 (4.3%) returned to the ED within 72 hours. Of the crowding indicators pertaining to total patients, the last 1 hour significantly affected decrease in RV (p=0.0046). Boarding patients were found to increase RV occurrence during the first 1 hour (p=0.0146) and 4 hours (p=0.0326). Crowding indicators that increased the likelihood of admission post-RV were total number of patients during the first 1 hour (p=0.0166) and 4 hours (p=0.0335) and evaluationg patients during the first 1 hour (p=0.0059). Overcrowding in the ED increased the incidence of RV and likelihood of post-RV admission. However, overcrowding at the time of ED departure was related to reduced RV.

Honey bees are vital organisms that provide ecological and economic value to humans. However, in recent years, the increase in honey bee losses due to various environmental factors, including pesticides, has become a growing concern. In Europe, neonicotinoid pesticides that are banned are being used without restrictions in the domestic setting, leading to ongoing damages as a result. Ongoing research is continually being conducted to demonstrate the risks associated with neonicotinoid pesticides. However, validation of the actual damages and impact in the field remains absent. Therefore, in this study, we observed changes in honey bee (Apis mellifera) colonies located near rice cultivation areas as they progressed beyond the rice pesticide application period. Furthermore, we collected honey bees exposed to the clothianidin and analyzed their stress-related gene expression. The results showed that the foraging behavior of honey bee colonies located near rice cultivation areas did not exhibit significant differences between the treatment site (Cheongyang and Gimje) and the control site (Wanju) during the experimental period. However, it was observed that the expression levels of stress-related genes in honey bees collected from the treatment group were significantly higher than those in the control. Most of the stress-related genes were associated with detoxification processes in response to pesticides. As a result, pesticide treatment in proximity to rice cultivation areas did not cause direct damage to honey bees but had an indirect impact, suggesting the potential for ongoing chronic damage.

Phosphate (Pi) starvation is a critical factor limiting crop growth, development, and productivity. Rice (Oryza sativa) R2R3-MYB transcription factors function in the transcriptional regulation of plant responses to various abiotic stresses and micronutrient deprivation, but little is known about their roles in Pi starvation signaling and Pi homeostasis. Here we identified the R2R3-MYB transcription factor gene OsMYB58, which shares high sequence similarity with AtMYB58. OsMYB58 expression was induced more strongly by Pi starvation than by other micronutrient deficiencies. Overexpressing OsMYB58 in Arabidopsis thaliana and rice inhibited plant growth and development under Pi-deficiency conditions. In addition, overexpression of OsMYB58 in plants exposed to Pi deficiency strongly affected root development, including seminal root, lateral root, and root hair formation. Overexpressing OsMYB58 strongly decreased the expression of the rice microRNAs, OsmiR399a and OsmiR399j. By contrast, overexpressing OsMYB58 strongly increased the expression of rice PHOSPHATE 2 (OsPHO2), whose expression is repressed by miR399 during Pi starvation signaling. OsMYB58 functions as a transcriptional repressor of the expression of its target genes, as determined by a transcriptional activity assay. These results demonstrate that OsMYB58 negatively regulates OsmiR399-dependent Pi starvation signaling by enhancing OsmiR399s expression.

Electricity generation from renewable energy sources is emerging as a result of global carbon emission reduction policies. However, most renewable energy sources are non-dispatchable and cannot be adjusted to meet the fluctuating electricity demands of society. A flexible operation process has been proposed as an effective solution to compensate for the unstable nature of renewable energy sources. Thermal load fluctuations during flexible operation may cause creep-fatigue damage to the high-temperature components of thermal power plants, as they are designed with a focus on creep damage under a constant power level. This study investigated the residual life of high-temperature components, such as a superheater tube and a reheater header, to failure under flexible operation conditions using finite element analysis and empirical models. First, we determine an analytical solution for the straightened superheater tube under thermal conditions and compare it with the numerical solution to verify the numerical models. Through the verified finite element model, the creep-fatigue life of the reheater header is estimated by considering flexible operation factors and employing the Coffin-Manson and Larson-Miller models. Although fatigue damage increases with decreasing minimum load and ramp rate, we confirmed that creep damage significantly affects the residual life during flexible operation. In addition, a surrogate model was proposed to evaluate the residual life of the reheater as a function of the flexible operation factors using the machine learning methodology, based on the results of finite element methods. It can be used to predict its residual life without performing complex thermal-structure analysis and relying on empirical models for fatigue and creep life. We expect our findings to contribute to the efficient operation of thermal power plants by optimizing the flexible operation factors.

This study was conducted to investigate the prevalence of Coxiella burnetii infection according to cattle breeds and growth types. A total of 491 cattle [cattle breed: 216 dairy cattle and 275 beef cattle; according to growth type: indoor housing (n = 294) and grazing (n = 197)] were tested for the presence of C. burnetii DNA and antibodies against C. burnetii using a commercial enzyme-linked immunosorbent assay (ELISA). Overall, 10.8% and 8.8% of the cattle were positive by PCR and for C. burnetii antibodies, respectively. The prevalence of C. burnetii was significantly higher in beef cattle than in dairy cattle using PCR (13.6% vs 7.4%; P = 0.032) and ELISA (14.6% vs 1.4%; P = 0.000), respectively. The overall infection rate of C. burnetii was significantly high in grazing cattle (PCR: 24.9%, ELSIA: 21.3%; P = 0.000) compared with housing cattle (PCR: 1.4%, ELISA: 0.3%). The results indicate that beef cattle have a significantly higher risk of contracting C. burnetii infection compared with dairy cattle (21.5% vs. 7.9%, χ2 = 5.82, P = 0.000, odds ratio = 3.197, 95% CI: 1.80-5.67). In addition, the infection of C. burnetii was significantly associated with grazing (P = 0.000). Moreover, a risk of contracting C. burnetii infection in grazing cattle was increased by 32.57-fold (95% CI: 12.84-82.60, P = 0.000) compared with indoor housed cattle. The phylogenetic analysis based on the IS111 gene revealed that our isolates were grouped together with humans, ticks, goats, and cattle isolates found in several countries. C. burnetii isolates circulating in the Republic of Korea exhibit genetic variations. Consequently, our results suggest that cattle are potential reservoirs for C. burnetii infection and most importantly, grazing acts as a high risk factor for the occurrence and transmission of this infection.

Arthrospira platensis is the widely available source of spirulina and contains distinctive natural pigments including carotenoids and C-phycocyanin (C-PC). In this study, the major carotenoid and C-PC contents were determined in seven commercially available spirulina powder products and laboratory-prepared A. platensis trichomes (AP-1) by an LC-DAD method and a UV-Visible spectrometry, respectively. The correlation of these two pigment content levels with Hunter color coordinates and antioxidant activity was also evaluated. The L* value failed to show a significant correlation with pigment content, but a positive correlation was observed between a* values and the contents of total carotenoid and C-PC. As b* values decreased, the total carotenoid and C-PC contents increased. AP-1 exhibited the highest content of total carotenoids, chlorophyll a and C-PC, and antioxidant activities among the samples. This observation could be related to degradation of these pigments during the mass production process. The carotenoid profiles suggested that the commercial spirulina powders originated from two different sources, A. platensis and A. maxima. Total carotenoid and C-PC content exhibited positive significant correlations with antioxidant activities measured by DPPH and ABTS assays. These results provide a strong scientific foundation for the establishment of standards for the commercial distribution of quality spirulina products.

Rapeseed (Brassica napus L.) is one of the most oil crop, and its commercial value is contingent upon its agronomic characteristics and oil quality. In this study, 73,226 single nucleotide polymorphisms (SNPs) across 95 rapeseed mutant lines derived from gamma rays and their original cultivar (‘Tamra’) obtained from genotyping-by-sequencing (GBS) was investigated gene ontology (GO) analysis and genome-wide association study (GWAS). GWAS was conducted on agronomic (plant height, ear length, thousand seed weight and seed yield) and oil (fatty acid and crude fat) traits. GO analysis showed that many genes displaying SNPs were involved in cellular processes, intracellular anatomical structures and organic cyclic compound binding. A total of 149 significant SNPs were associated with the agronomic traits (76 SNPs) and oil traits (73 SNPs). Bna.A05p02350D (SFGH) and Bna.C02p22490D (MDN1) were selected as novel candid genes for thousand seed weight. In addition, Bna.C03p14350D (EXO70) and Bna.A09p05630D (PI4Kα1) were selected as novel candidate genes for the erucic acid and crude fat content, respectively. These findings could facilitate the identification of optimal genotypes for breeding new cultivars, and association studies represent an economically efficient tool for mutant screening and the selection of elite rapeseed-breeding lines.

Background: Patients undergoing dual antiplatelet therapy (DAPT) may experience recurrent gastrointestinal bleeding (GIB). We investigated the clinical characteristics and risk factors for recurrent non-variceal upper gastrointestinal bleeding (NVUGIB) in patients who had experienced NVUGIB during receiving DAPT. Methods: We enrolled patients diagnosed with NVUGIB during receiving DAPT between 2006 and 2020. Definite bleeding was confirmed by esophagogastroduodenoscopy in all NVUGIB patients. Results: A total of 124 patients were diagnosed with NVUGIB during receiving DAPT. Male was predominant (n = 103, 83.1%), bleeding mostly from the stomach (n = 94, 75.8%) and peptic ulcers (n = 72, 58.1%). After successful hemostasis of NVUGIB, 36 patients (29.0%) experienced at least one episode of recurrent upper GIB, 19 patients (15.3%) died, and 7 (5.6%) patients had a bleeding-related death. Multivariate analysis showed that age was a significant factor for re-bleeding (odds ratio [OR],1.050; 95% confidence interval [CI]:1.001-1.102, P-value:0.047), all-cause mortality (OR,1.096; 95% CI:1.020-1.178, P=0.013), and re-bleeding related mortality (OR,1.187; 95% CI:1.032-1.364, P-value:0.016). In Kaplan-Meier analysis, the cumulative probabilities of re-bleeding, death, and bleeding-related death were significantly higher in patients aged 70 and older (P=0.008, &lt;0.001, and 0.009, respectively). Conclusion: Clinicians should be cautious about re-bleeding and mortality when elderly patients who experienced NVUGIB during receiving DAPT.Keywords: dual antiplatelet therapy; upper gastrointestinal tract; bleeding; mortality

The microstructure and hardness along the thickness direction of a water quenched, high-strength thick plate with a thickness of 40 mm were investigated with three specimens from the thick plate: surface, 1/4t, and 1/2t (center) thickness, and the phase transformation behavior of the thick plate according to the cooling rate was analyzed through dilatometric experiments. Finally, the cooling rate for each thickness of the thick plate was estimated by comparing the microstructure and hardness of the thick plate along the thickness with those of the dilatometric specimens. Martensite microstructure was observed on the surface of the water quenched thick plate due to the fast cooling rate. On the other hand, an inhomogeneous microstructure was transformed inside the thick plate due to the relatively slow cooling rate and central segregation of Mn. A small fraction of bainite was shown at 1/4t thickness. A banded microstructure with martensite and bainite resulting from Mn segregation was developed at 1/2t; that is, the full martensite microstructure was transformed in the Mn-enriched area even at a slow cooling rate due to high hardenability, but a bainite microstructure was formed in the Mn-depleted area owing to relatively low hardenability. A portion of martensite with fine cementite at the surface and 1/4t was identified as auto-tempered martensite with a Bagaryatskii orientation relationship between the ferrite matrix and cementite. The microstructure and hardness as well as dilatation were investigated at various cooling rates through a dilatometric experiment, and a continuous cooling transformation (CCT) diagram was finally presented for the thick plate. Comparing the microstructure and hardness at the surface, 1/4t, and 1/2t of the thick plate with those of dilatometric specimens cooled at various cooling rates, it was estimated that the surface of the thick plate was cooled at more than 20 oC/s, whereas the 1/4t region was cooled at approximately 5 ~ 10 oC/s during water quenching.

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

There is a lack of data comparing sugammadex with anticholinesterase for the quality of anaesthesia recovery, especially following a single bolus dose of rocuronium. Thus, we evaluated the influence of reversal with sugammadex or neostigmine on post-operative quality of recovery by using the Post-operative Quality Recovery Scale (PQRS). A total of 86 patients undergoing trans-pars plana vitrectomy (TPPV) under general anaesthesia were intubated following a single bolus dose of rocuronium (0.6 mg/kg). At the end of surgery, patients were received either neostigmine or sugammadex. The quality of recovery was assessed using the PQRS at 15 minutes and 40 minutes after surgery, and on post-operative day 1. The recovery rate in the physiological domain was higher in the sugammadex group at 15 minutes after surgery (P = 0.02). Though there were no significant differences in the overall cognitive recovery domain, patients in the sugammadex group could recall more numbers in reverse order. However, there were no significant differences between the groups in the other domains of the PQRS. The use of sugammadex may increase the quality of the post-operative physiological recovery at early post-operative periods compared with neostigmine use following a single bolus dose of rocuronium in patients undergoing TPPV with general anaesthesia.

This study provides a comprehensive analysis of global patent trends in battery recycling, focusing on secondary batteries and related technologies across Korea, China, and the United States. The data, collected from various patent databases, was quantitatively analyzed to identify technology trends and direct future development. The analysis reveals distinct emphases on technologies such as lithium-ion and waste battery recycling, highlighting notable differences in patent activities among key companies and countries. China's large number of patents in battery manufacturing processes contrasts with the USA's focus on electrochemical cell construction and storage systems, while Korea shows significant activity in waste battery technology. The study underscores the competitive landscape and innovation efforts in the battery recycling sector, providing insights into the technological focuses and priorities of each country. It also identifies key challenges, such as the need for consistent innovation and broader geographic coverage in Korea, enhancing patent influence and international presence in China, and ensuring high patent quality and fostering innovation in lagging sectors in the United States. Addressing these challenges through enhanced collaboration, increased R&D investments, and supportive policies is crucial for strengthening the global position and driving further innovation in the battery recycling sector.

REV-ERBα and its paralog, REV-ERBβ encoded by NR1D1 and NR1D2 genes, are key nuclear receptors that link the circadian timing system and metabolic homeostasis. Since heme is an endogenous ligand, REV-ERBs have been considered key components of the circadian molecular clock that can be pharmacologically targeted to treat various circadian rhythm-related diseases, such as cardiometabolic, inflammatory, and neuropsychiatric diseases, as well as cancer. REV-ERBs are believed to be functionally redundant and compensatory, although they often affect the expression of gene subsets in an isoform-specific manner. Therefore, this study aimed to identify the redundant and distinct roles of each isoform in controlling its target genes by comparing the transcriptome profiles of a panel of mutant U2OS human osteosarcoma cells in which either NR1D1 or NR1D2 was ablated. Indeed, our transcriptomic analyses revealed that most REV-ERB-regulated genes were controlled by redundant or even additive actions. However, the RNA expression profiles of each single mutant cell line also provided strong evidence for isoform-dependent actions. For example, REV-ERBα were more responsible for regulating the NF-κΒ signaling pathway, whereas a group of extracellular matrix components required REV-ERBβ to maintain their expression. We found that REV-ERBs have isoform-selective functions in the regulation of certain circadian output pathways, despite their overlapping roles in the circadian molecular clock. Thus, the development of isoform-selective REV-ERB modulators may help treat metabolic disturbances and certain types of cancer.

Though Moracin D derived from Morus alba was known to have anti-inflammatory and antioxidant activities, the underlying antitumor mechanism of Moracin D was never unveiled so far. Thus, in the recent study, the apoptotic mechanism of Moracin D was elucidated in breast cancer cells. Herein, Moracin D exerted significant cytotoxicity in MDA-MB231 and MCF7 cells. Also, Moracin D increased sub G1 population, cleaved poly (ADP-ribose) polymerase (PARP) and attenuated the expression of pro-cysteine aspartyl-specific protease (procaspase 3), c-Myc, cyclin D1, B-cell lymphoma 2 (Bcl-2),and X-linked inhibitor of apoptosis protein (XIAP) in MDA-MB231 cells. Of note, Moracin D reduced expression of Forkhead box M1 (FOXM1), β-catenin, Wnt3a, and upregulated glycogen synthase kinase 3 beta (GSK 3β) on Tyr216 along with disturbed binding of FOXM1 with β-catenin in MDA-MB-231 cells. Conversely, GSK3β inhibitor SB216763 reversed the apoptotic ability of Moracin D to reduce expression of FOXM1, β-catenin, pro-caspase3 and pro-PARP in MDA-MB-231 cells. Overall, these findings provide novel insight that Moracin D inhibits proliferation and induces apoptosis via suppression of Wnt3a/FOXM1/β-catenin signaling and activation of caspase and GSK3β

In applied mathematics, statistics, operation research, physics, and engineering mathematics, confluent representations of hypergeometric functions in one and two variables are known to exist, and their occurrence in a variety of applications is also well recognised. In this article, we intend to present a new derivation of the extended Watson summation theorem for the Kim et al. given series 4F3. We assessed four attractive integrals involving generalized hypergeometric function as an application. With a few particular cases, this note will come to an end. In the results given above, symmetry appears on its own.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

Interstitial lung disease (ILD) is one of the most serious extra-articular complications of rheu-matoid arthritis (RA), which increases the mortality of RA. Because the pathogenesis of RA-ILD remains poorly understood, appropriate therapeutic strategies and biomarkers have not yet been identified. Thus, the goal of this review was to summarize and analyze the reported data on the etiology and pathogenesis of RA-ILD. The incidence of RA-ILD increases with age, and is also generally higher in men than in women and in patients with specific genetic variations and eth-nicity. Lifestyle factors associated with an increased risk of RA-ILD include smoking and exposure to pollutants. The presence of an anti-cyclic citrullinated peptide antibody, high RA disease activity, and rheumatoid factor positivity also increase the risk of RA-ILD. We also explored the roles of biological processes (e.g., fibroblast–myofibroblast transition, epithelial–mesenchymal transition, and immunological processes), signaling pathways (e.g., JAK/STAT and PI3K/Akt), and the his-topathology of RA involved in RA-ILD pathogenesis based on published preclinical and clinical models of RA-ILD in animal and human studies.

Laser shock peening is a process which can reduce stress corrosion cracking and improve fatigue life by forming compressive residual stress on the surface of the material. In a computational FE simulation of laser shock peening, during applying the pressure load generated by the laser pulse to the surface of simulation geometry, the peening is simulated by explicit analysis and then convert to implicit analysis to dissipate the dynamic energy remaining in the geometry. In this study, static damping is applied to dissipate residual dynamic energy without converting it into an implicit analysis. The compressive residual stress distribution is compared between the simulation results for the stainless steel 304 material and the same material subjected to actual laser shock peening. The laser shock peening parameters were 4.2J laser pulse energy, 50% overlap of 3mm diameter of the laser beam and water as a confinement layer. As a result, the compressive residual stress from the surface to the depth direction is similar to both the simulation and the experimental result measured by the hole drilling method.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

Hutchison-Gilford progeria syndrome (HGPS) is an extremely rare genetic disorder caused by the mutant protein progerin, which is expressed by the abnormal splicing of LMNA gene. HGPS affects systemic levels, except cognition or brain development in children, showing that cellular aging can occur in the short term. However, the causes of aging that humanity is working to overcome remain poorly understood. Studying progeria could be useful for unraveling the causes of human aging (as well as fatal age-related disorders). Elucidating the clear cause of HGPS or the development of a therapeutic medicine will provide inconceivable comfort for young patients and enable them to live a normal life. This review aimed to: i) briefly describe how progerin was discovered as the causative agent of HGPS, ii) elucidate the puzzling observation of the absence of primary neurological disease in HGPS, iii) present several studies showing the deleterious effects of progerin and the beneficial effects of its inhibition, and iv) summarize research to develop a therapy for HGPS, and introduce clinical trials for its treatment.

Accumulating reports have suggested that an inability to clear dead cells is a cause of inflammation and cancer and that the fascia is associated with cancer metastasis. Novel corpuscle-connected filiform structures (CCFSs) entangled on the fascia of the internal organs of rats were selectively visualized with high repeatability (93%) under vital staining with Janus Green B (JGB). Serial sections of CCFSs stained with haematoxylin and eosin and with Mattson Trichrome were microscopically examined. In parallel, the immunohistochemistry with CD31, Lyve 1, scanning electron microscopy, and transmission electron microscopy (TEM) were also used to investigate the novel properties of the CCFSs. All of the CCFSs enclosed JGB-stained granules, which was verified by the impromptu coupling of stereo and light microscopes and fluorescence-activated cell sorting. The functions of the CCFSs were discovered under fluorescence microscopy and confocal laser scanning microscopy to be implicated in cell death: fragmented DNAs and f-actins with extracellular DNAs. The dead cells in the CCFSs were verified by using terminal deoxynucleotidyl transferase dUTP nick end labelling and TEM. Moreover, the CCFS had a relatively-high concentration of calcium, a main element for cell death in tissue, which was measured in 2-dimensionally images using time-of-flight secondary ion mass spectrometry. Taken these results, we report for the first time that novel reticular CCFSs are widely entangled on the fascia of the internal organs of rats with the implication for cell death.

Objectives: To assess clinical implications of increased nuchal translucency (INT) in twin pregnancies based on the chorionicity. Methods: This was a retrospective review of the twin pregnancies who underwent first trimester ultrasound with nuchal translucency (NT) measurement at 11-13 weeks of gestation from January 2006 to December 2014. Data were collected using the OB database and the chart review. Pregnancy outcomes including gestational weeks at the delivery, abnormal fetal karyotypes, fetal structural anomalies, twin specific complications were analyzed. Results: A total of 1,622 twin pregnancies with INT≥95th percentile in one or both fetuses were identified. In all twin pregnancies with INT, abnormal fetal karyotypes were identified in 17 (8.6%) patients (odds ratio=13.28, CI=5.990-29.447, P=0.000) and twin-specific complications were identified in 23 (11.6%) patients (odds ratio=2.398, CI=1.463-3.928, P=0.001) compared to those with normal NT. Among the INT group, when the groups were subdivided into monochorionic (MC) and dichorionic (DC) pregnancies, 14.8% and 29.6% of the MC pregnancies had structural anomalies in one or both fetuses (odds ratio=5.774, 95% CI=1.445-23.071, P=0.01) and twin-specific complications (odds ratio=4.379, 95% CI=1.641-11.684, P=0.03), respectively, compared to DC pregnancies. The prevalence of abnormal fetal karyotypes was not statistically different in patients with INT when compared between MC and DC pregnancies (P=0.329). Conclusions: INT was associated with a higher rate of twin-specific complications and fetal structural anomalies in MC twin pregnancies rather than abnormal fetal karyotype. Therefore, NT measurement in MC twin pregnancies can be a useful tool for prediction of adverse pregnancy outcomes. Appropriate counseling and surveillance based on the chorionicity is imperative in prenatal care of twin pregnancies.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

The purpose of this study is to develop and evaluate a self-microemulsifying drug delivery system (SMEDDS) to improve the oral absorption of poorly water-soluble Olaparib. Through the solubility test of Olaparib in various oils, surfactants and co-surfactants, pharmaceutical excipients for use in SMEDDS manufacturing were selected. Self-emulsifying regions were identified by mixing the selected materials at various ratios, and a pseudoternary phase diagram was constructed by synthesizing these results. Various physicochemical properties of microemulsion incorporating Olaparib were confirmed by investigating the particle morphology, particle size, zeta potential, drug content and stability. In addition, the improved dissolution and oral absorption of Olaparib were also confirmed through a dissolution test and a pharmacokinetic study. An optimal microemulsion was generated in the formulation of Capmul MCM EP/NF 10%, Labrasol 80% and PEG 400 10%. Fabricated nano-sized microemulsions were well-dispersed in aqueous solutions, and it was also confirmed that it was maintained well without any problems of either physical or chemical stability. The 5 min initial dissolution of Olaparib in fabricated formulations was improved by 10.6 times (pH1.2), 14.8 times (pH6.8) and 14.8 times (distilled water) compared to the values of Olaparib powder. The dissolution at 120min was 45.4±4.0%(pH1.2), 53.5±1.1% (pH6.8) and 58.1±1.00% (distilled water) in Olaparib powder but has been significantly improved by 1.7 times (74.8±1.9%), 1.6 times (84.2±0.3%) and 1.5 times (81.2±0.7%) in SMEDDS. Associated with the high dissolutions of Olaparib in fabricated microemulsions, the pharmacokinetic parameters were also greatly improved. The Cmax and AUCinf of Olaparib in the prepared microemulsion were increased 4.2- and 3.2-fold, respectively, compared to powder. Taken together with the results mentioned above, the microemulsion system could be an effective tool as an oral delivery formulation for Olaparib. Additionally, our results demonstrate that the SMEDDS systems comprising Capmul MCM, Labrasol and PEG 400 could be a useful option for improvement of several other poorly water-soluble drugs with physico-chemical properties similar to Olaparib.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

The aim of this study was to analyze whether the respiratory variation in ECG standard lead II R-wave amplitude (ΔRDII) could be used to assess intravascular volume status following inferior vena cava (IVC) clamping. This clamping causes an acute decrease in cardiac output during liver transplantation (LT). We retrospectively compared ΔRDII and related variables before and after IVC clamping in 34 recipients. Receiver operating characteristic (ROC) curve and area under the curve (AUC) analyses were used to derive a cutoff value of ΔRDII for predicting pulse pressure variation (PPV). After IVC clamping, cardiac output significantly decreased while ΔRDII significantly increased (P = 0.002). The cutoff value of ΔRDII for predicting a PPV >13% was 16.9% (AUC: 0.685) with a sensitivity of 57.9% and specificity of 77.6% (95% confidence interval 0.561 – 0.793, P = 0.015). Frequency analysis of ECG also significantly increased in the respiratory frequency band (P = 0.016). Although significant changes in ΔRDII during vena cava clamping were found at norepinephrine doses < 0.1 μg/kg/min (P = 0.014), such changes were not significant at norepinephrine doses > 0.1 μg/kg/minP = 0.093). ΔRDII could be a noninvasive dynamic parameter in LT recipients presenting with hemodynamic fluctuation. Based on our data, we recommended cautious interpretation of ΔRDII may be requisite according to vasopressor administration status.

In this paper, a positive answer to the open question of Fabino et al. is given, and the concept of I\c sik type set valued contractions is introduced and fixed point theorem for such contractions is established. Examples to support main theorems are given, and an application to integral inclusion is given.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

Identifying the primary site of origin of metastatic cancer is vital for guiding treatment decisions, especially for patients with cancer of unknown primary (CUP). Despite advanced diagnostic techniques, CUP remains difficult to pinpoint and is responsible for a considerable number of cancer-related fatalities. Understanding its origin is crucial for effective management and potentially improving patient outcomes. This study introduces a machine learning framework ONCOfind-AI that leverages transcriptome-based gene set features to enhance the accuracy of predicting the origin of metastatic cancers. By ensuring compatibility between RNA-sequencing and micro-array data, we were able to construct a more comprehensive training dataset. Integrating data from different platforms improved the accuracy of our machine learning models for predicting cancer origins. Our method was validated using external data from clinical samples collected through Kangbuk Samsung Medical Center and the Gene Expression Omnibus. The external validation results demonstrated a top-1 accuracy ranging from 0.80 to 0.86, with a top-2 accuracy of 0.90. This study highlights that incorporating biological knowledge through curated gene sets can merge gene expression data from different platforms, enhancing the compatibility needed for more effective machine learning prediction models.

Background: Idiopathic pulmonary fibrosis (IPF) is a progressive fibrotic lung disease with a poor prognosis. Pirfenidone is approved and widely used for the treatment of IPF and reduces lung function decline. The aim of this study was to evaluate the efficacy of different doses of pirfenidone for the prevention of disease progression in patients with IPF. Methods: This was a prospective, observational, single-center cohort study conducted in Haeundae Paik Hospital, Republic of Korea, from April 2021 to March 2023. IPF patients were assigned to three groups according to the dose of pirfenidone (600mg, 1,200mg, 1,800mg). The primary endpoint was the efficacy of pirfenidone according to dose for the prevention of disease progression over 12 months. The secondary endpoint was the role of Krebs von den Lungen-6 (KL-6) in predicting disease progression. Results: A total of 44 patients were enrolled, of whom 39 completed the study, with 13 patients assigned to each of the three groups. The median age was 71.7 years, and 79.5% of patients were men. The baseline characteristics were similar across groups, except the 600mg group was older (75.9 vs. 69.2 vs. 68.2 years, p = 0.016). Fourteen patients (35.9%) suffered disease progression. The rate of disease progression did not differ according to the dose of pirfenidone (38.5 vs. 38.5 vs. 30.8%, p = 1.000). In multivariable logistic regression analysis, KL-6 was not a statistically significant predictor of disease progression. Conclusions: In our study, regardless of dose, consistent pirfenidone use for 12 months resulted in similar efficacy for the prevention of disease progression in patients with IPF. Large-scale, randomized, double-blind, placebo-controlled clinical trials are needed.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

Background The purpose of this study was to evaluate the prevalence of velamentous cord insertion (VCI) and the actual association between pathologically confirmed VCI and perinatal outcomes in twins based on the chorionicity. Methods All twin pregnancies who received prenatal care at a specialty clinic for multiple pregnancies, from less than 12weeks of gestation until delivery in a single institution between 2015 and 2018 were included in this retrospective cohort study. Results A total of the 941 twins were included in the study. The prevalence of VCI in dichorionic (DC) twins and monochorionic diamniotic (MCDA) twins was 5.8% and 7.8%, respectively (p=0.251). In all study population, the prevalence of vasa previa and placenta accreta were higher in VCI group compared to that of non-VCI group (p=0.008 and 0.022). In MCDA twins with VCI, birth weight, 1 and 5-minute Apgar score were lower compared to DC twins with VCI (p=0.010, 0.002 and 0.000). There was no significant association between VCI and selective fetal growth restriction (p=0.708), twin-to-twin transfusion syndrome (p=0.400) and birth-weight discordance (>20% and >25%) (p= 0.378 and 0.161) in MCDA twins. Conclusion VCI in twins was not a risk factor for adverse perinatal outcomes and twin-specific complications.

(1) Background: Multiple alterations of cellular metabolism have been documented in experimental studies of autosomal dominant polycystic kidney disease (ADPKD) and are thought to contribute to its pathogenesis. (2) Methods: To elucidate the molecular pathways and transcriptional regulators associated with the metabolic changes of renal cysts in ADPKD, we compared global gene expression data from human PKD1 renal cysts, minimally cystic tissues (MCT) from the same patients, and healthy human kidney cortical tissue samples. (3) Results: We found PKD1 renal cysts displayed the Warburg effect with gene pathway changes favoring increased cellular glucose uptake and lactate production, instead of pyruvate oxidation. Additionally, mitochondrial energy metabolism was globally depressed, associated with downregulation of gene pathways related to fatty acid oxidation (FAO), branched-chain amino acid (BCAA) degradation, the Krebs cycle, and oxidative phosphorylation (OXPHOS) in renal cysts. Activation of mTORC1 and its two target proto-oncogenes, HIF-1α and MYC, was predicted to drive the expression of multiple genes involved in the observed metabolic reprogramming (e.g., GLUT3, HK1/HK2, ALDOA, ENO2, PKM, LDHA/LDHB, MCT4, PDHA1, PDK1/3, MPC1/2, CPT2, BCAT1, NAMPT); indeed, their predicted expression patterns were confirmed by our data. Conversely, we found AMPK inhibition was predicted in renal cysts. AMPK inhibition was associated with decreased expression of PGC-1α, a transcriptional coactivator for transcription factors PPARα, ERRα, and ERRγ, all of which play a critical role in regulating oxidative metabolism and mitochondrial biogenesis. (4) Conclusions: These data provide a comprehensive map of metabolic pathway reprogramming in ADPKD and highlight nodes of regulation that may serve as targets for therapeutic intervention.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

The continuous advancement of Artificial Intelligence (AI) technology depends on the efficient processing of unstructured data, encompassing text, speech, and video. Traditional serial computing systems based on the von Neumann architecture, employed in information and communication technology development for decades, not suitable for the concurrent processing of massive unstructured data tasks with relatively low-level operations. As a result, there arises a pressing need to develop novel parallel computing systems. Recently, there has been a burgeoning interest among developers in emulating the intricate operations of the human brain, which efficiently processes vast datasets with remarkable energy efficiency. This has led to the proposal of neuromorphic computing systems. Of these, Spiking Neural Networks (SNNs), designed to closely resemble the information processing mechanisms of biological neural networks, are subjects of intense research activity. Nevertheless, a comprehensive investigation into the relationship between spike shapes and Spike-Timing-Dependent Plasticity (STDP) to ensure efficient synaptic behavior remains insufficiently explored. In this study, we systematically explore various input spike types to optimize the resistive memory characteristics of Halfnium-based Ferroelectric Tunnel Junction (FTJ) devices. Among the various spike shapes investigated, the square-triangle (RT) spike exhibited good linearity and symmetry, and a wide range of weight values could be realized depending on the offset of the RT spike. These results indicate that the spike shape serves as a crucial indicator in the alteration of synaptic connections, representing the strength of the signals.

Alopecia refers to the continuous shedding of hair from the scalp or other areas. Genetic factors are the most common of the variety of causes of alopecia. Male pattern baldness, also known as androgenic alopecia, is prevalent. Recently, the interest in hair loss treatment has increased due to the growing number of people experiencing anxiety and stress related to hair loss. Nepenthes kampotiana Lecomte is known for its anticancer effects, but its potential for preventing hair loss has not been researched. Therefore, this study focused on the hair loss prevention effects of N. kampotiana Lecomte ethanol extract (Nk-EE). The results showed that Nk-EE has a proliferative effect on human follicle dermal papilla cells and inhibited cell death. In vivo experiments using androgenic areata models showed that Nk-EE had a positive effect on a variety of biomarkers such as hair-to-skin ratio, hair type frequency, and hair thickness. The results of this study suggest that Nk-EE has the potential to be an effective treatment for androgenic alopecia.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

Mitochondria are highly dynamic organelles that continuously change their shape. Their main function is ATP production; however, they are additionally involved in a variety of cellular phenomena, such as apoptosis, cell cycle, proliferation, differentiation, reprogramming, and aging. The change in mitochondrial morphology is closely related to the functionality of mitochondria. Normal mitochondrial dynamics are critical for cellular function, embryonic development, and tissue formation. Thus, defect in proteins involved in mitochondrial dynamics that control mitochondrial fusion and fission can affect cellular differentiation, proliferation, cellular reprogramming, and aging. Here we review the processes and proteins involved in mitochondrial dynamics and its various associated cellular phenomena.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

This study delves into the critical domain of public procurement, specifically focusing on Sustainable Public Procurement (SPP) and Environmental, Social, and Governance (ESG) considerations within the context of South Korea. The aim of this research is to empirically scrutinize the factors influencing the impact index of SPP, with a particular emphasis on services related to labor standards. The investigation spans three years, from January 1, 2019, to July 31, 2021, encompassing state agency orders and post-implementation legal changes. Leveraging the comprehensive Korea On-line E-Procurement Sys-tem(KONEPS) platform, we meticulously collected data, ultimately culminating in 21,573 services meeting our criteria, from which 250 cases underwent an in-depth analysis. The study sheds light on the influence of social responsibility evaluation cri-teria on overall procurement scores, while also uncovering the moderating effects of various factors. The outcomes of this study offer valuable insights into the impact index of social responsibility evaluation criteria within South Korea's public procurement landscape. Factors including procurement year, classification, service period, and estimated price were identified as significant influencers. Moreover, the number and location of evalu-ation criteria items, inclusion of sincerity elements, and the evaluating agency were deemed pivotal determinants of the influence index. These findings hold profound implications for policymakers, procurement practitioners, and researchers and provide a roadmap for optimizing the utilization of social responsibility evaluation criteria to advance responsible and sustainable procurement practices. Future research avenues include conducting further study of additional moderat-ing variables, expanding datasets to encompass a broader spectrum of procurement contexts, and evaluating the long-term repercussions of social responsibility evaluation on procurement outcomes. These endeavors promise to further refine and advance public procurement practices in South Korea and beyond.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.