This paper introduces a chip-level oven-controlled system for improving the temperature stability of MEMS resonators. Wherein the resonator and the micro-hotplate are manufactured by MEMS technology, then wire-bounded in a package shell at the chip level. The proposed resonator is transduced by the AlN film, and its temperature is monitored by temperature-sensing resistors on both sides. The designed micro-hotplate is placed at the bottom of the resonator chip as a heater and insulated by airgel. The PID pulse width modulation (PWM) circuit controls the heater according to the temperature detection result to provide a constant temperature for the resonator. The proposed oven-controlled MEMS resonator (OCMR) exhibits a frequency drift of 3.5ppm in the range of -50°C to 125°C, and the method also can be applied to other MEMS devices that require temperature control.

There are two contrary opinions regarding the risk if mainland China (MC) moves away from its zero-COVID policy. Some experts think the risk shall be much lower than influenza as per MC’s own COVID-19 case fatality rate (CFR), while some other experts think the risk shall be much higher than influenza as per the COVID-19 CFRs of other regions. We elucidate here that this and multiple other striking differences in the CFR between various scenarios all support and substantially resulted from the view that good IDM is highly powerful to mitigate COVID-19, where IDM (isolation-disinfection-maintenance) means isolation of COVID-19 cases from other people, disinfection of their living environments, and health maintenance (e.g., rest, nutrition, breathing). The high effect of good IDM is also supported by the theoretic functions of IDM in minimizing co-infections and maintaining body functions, and the fact that all the 505 COVID-19 deaths reported in MC in 2022 before May 5 died directly of severe underlying diseases with COVID-19. Although it is tough for people in poverty to obtain good IDM, good IDM can be feasible at home for the most mild cases and in hospitals for the most severe cases. Therefore, good IDM can be crucial to mitigating COVID-19 worldwide. It also suggests that the risk for China to end its zero-COVID policy depends on China’s control policies or measures. Based on the effect of IDM, the cautious co-existence policy was proposed for COVID-19 control. This policy could reduce the whole death toll in MC because good IDM is non-specific and can reduce deaths of various other diseases. The cautious co-existence policy (non-specific) and the vaccination policy (specific) aid each other to mitigate COVID-19, and they cannot replace each other. Those who are qualified in health for vaccination should be vaccinated against COVID-19 timely.

This paper explores the use of different deep learning models for predicting precipitation in 56 meteorological stations in Jilin Province, China. The models used include Stacked-LSTM, Transformer, and SVR, and Gaussian noise is added to the data to improve their robustness. Results show that the Stacked-LSTM model performs the best, achieving high prediction accuracy and stability. The study also conducts variable attribution analysis using LightGBM and finds that temperature, dew point, precipitation in previous days, and air pressure are the most important factors affecting precipitation prediction, which is consistent with traditional meteorological theory. The paper provides detailed information on the data processing, model training, and parameter settings, which can serve as a reference for future precipitation prediction tasks. The findings suggest that adding Gaussian noise to the dataset can improve the model's generalization ability, especially for predicting days with zero precipitation. Overall, this study provides useful insights into the application of deep learning models in precipitation prediction and can contribute to the development of meteorological forecasting and applications.

High density of buildings and the large traffic volume of cities give rise to narrow spaces and high passenger flows in most subway stations. When evacuation is required during an emergency, these problems may trigger issues in operational safety. Therefore, it is imperative to comprehensively assess subway station emergency evacuation times and capacities during the operating process to ensure the design is safe, science-based, and rational. To further enhance safe evacuation capacity, this paper proposes an overall evacuation time model that considers the multielement charac-teristics of subway stations in multiple segments. The evacuation route is decomposed into five stages according to the critical nodes in the evacuation process. An overall emergency evacuation time model is established based on the diversity of bottlenecks in the five stages, integrating elements such as the horizontal movement velocity of passengers, subway equipment parameters, and human density. Taking Xi’an Wulukou Subway Station as an example, this paper verifies the outcomes of the theoretical model against the Pathfinder software and conducts additional anal-yses of the evacuation conditions of stairs and exits. The results show that the error between the theoretical emergency evacuation time and simulation evacuation time was 5.4%, The emergency evacuation model established in this study boasts strong robustness and stability.

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Human monkeypox, caused by monkeypox virus, has spread unprecedentedly to more than 100 countries since May 2022. Here we summarized the epidemiology of monkeypox through a literature review and elucidated the risks and elimination strategies of this outbreak mainly based on the summarized epidemiology. We demonstrated that monkeypox virus became more contagious and less virulent in 2022, which could result from the fact that the virus entered a special transmission network favoring close contacts (i.e., sexual behaviors of men who have sex with men outside Africa) and the possibility that the virus accumulated a few adaptive mutations. We gave the reasons to investigate whether cattle, goats, sheep, and pigs are susceptible to monkeypox virus and whether infection with monkeypox virus could be latent in some primates. We listed six potential scenarios for the future of the outbreak (e.g., the outbreak could lead to endemicity outside Africa with increased transmissibility or virulence). We also listed multiple factors aiding or impeding the elimination of the outbreak. We showed that the control measures strengthened worldwide after the World Health Organization declared the outbreak a public health emergency of international concern (PHEIC) could eliminate the outbreak in 2022. We clarified eight strategies, i.e., publicity and education, case isolation, vaccine stockpiling, risk-based vaccination or ring vaccination, importation quarantine, international collaboration, and laboratory management, for the elimination of the outbreak.

Mulberry is an economically significant crop for the sericulture industry worldwide. Stresses such as drought exposure have a significant influence on plant survival. Metabolome directly reflects plant physiological status; thus, a way to assess this impact is to perform a global metabolomic analysis. This study investigated the effect of drought stress on mulberry Yu-711 metabolic balance using a liquid chromatography-mass spectrometry (LC-MS) based on an untargeted metabolomic approach. For this objective, Yu-711 leaves were subjected to two weeks of drought stress treatment and control without drought stress. Multivariate and univariate statistical analyses highlighted numerous differentially-accumulated metabolic elements as a function of time and treatment. Drought stress led to a more differentiated metabolites response than the control. We found that the levels of total lipids and galactolipids, and phospholipids (PC, PA, PE) were significantly altered, producing 48% of the total differentially expressed metabolites. Fatty acyls were the most abundant lipids expressed and decreased considerably by 73.6%. Prenol lipids class of lipids increased in drought leaves. Other classes of metabolites, including polyphenols( flavonoids and cinnamic acid), organic acid (amino acids), carbohydrates, benzenoids, and organoheterocyclic, all had a dynamic trend in response to the drought stress. However, their levels under drought stress generally decreased significantly compared to the control. These results provide an overview of the metabolic profile of the mulberry plant through differentially-accumulated compounds and provide a better understanding of global plant metabolic changes in defense mechanisms.

Numerous studies have demonstrated that multiple intrinsic and extrinsic factors shape the structure and composition of gut microbiota in a host. The disorder of gut microbiota may trigger various host diseases. Here, we collected fecal samples from wild-caught Japanese geckos (Gekko japonicus) and captive conspecifics fed with mealworms (mealworm-fed geckos) and fruit flies (fly-fed geckos), aiming to examine dietary and sexual correlates of gut microbiota. We used the 16S rRNA gene sequencing technology to determine the composition of gut microbiota. The dominant phyla with a mean relative abundance higher than 10% were Verrucomicrobiota, Bacteroidota and Firmicutes. Gut microbial community richness was higher in mealworm-fed geckos than in fly-fed and wild geckos, and community diversity was higher in mealworm-fed geckos than in wild geckos. Neither alpha nor beta diversity of gut microbiota differed among wild, mealworm-fed and fly-fed geckos. The beta rather than alpha diversity of gut microbiota was sex-dependent. Based on the relative abundance of gut bacteria and its gene functions, we concluded that gut microbiota contributed more significantly to the host’s metabolic and immune functions. Higher diversity of gut microbiota in mealworm-fed geckos could result from higher chitin contents of insects of the order Coleoptera. This study not only provides basic information about the gut microbiota of G. japonicus, but also shows that gut microbiota correlates with dietary habit and sex in the species.

Heart regeneration after myocardial infarction remains challenging in reconstruction of blood resupply system. Here, we find that in zebrafish heart after resection of the ventricular apex, the local myocardial cells and the clotted blood cells undergo cell remodeling process via cytoplasmic exocytosis and nuclear reorganization within revascularization-based blastema. The regenerative processes are visualized by spatiotemporal expression of three blastema representative factors (alpha-SMA- which marks for fibrogenesis, Flk1for angiogenesis/hematopoiesis, and Pax3a for remusculogensis)，and two histone modifications (H3K9Ac and H3K9Me3 mark for chromatin remodeling). Using the cultured zebrafish embryonic fibroblasts we identify blastema fraction components and show that Krt5 peptide could link cytoskeleton network and BMP4 signaling pathway to regulate the transcription and chromatin accessibility at the blastema representative genes and bmp4 genes. Our study provides new mechanistic insights into the epithelial-dependent and revascularization-based blastema regeneration for potential myocardial infarction therapy.

In recent years, the taxonomy of the families of Phenuiviridae, Nairoviridae, and Peribunyavidae in Bunyavirales was updated frequently, because many novel viruses in these families have been identified and the species demarcation criteria of these families have been changed. As per these criteria and sequence analysis, we found that the taxonomy of 19 species in these families should be revised. We presented six proposals for optimizing virus species taxonomy using the examples from these families. First, the species demarcation criteria for the same family (e.g., Peribunyavidae) should be unified. Second, the methods and parameters for the taxonomic calculation in the same order (e.g., Bunyavirales) should be unified. Third, virus species taxonomy should be based on phylogenetic relationships, rather than a cutoff value of sequence identities that is a self-contradictory demarcation criterion, although sequence identities aid virus taxonomy greatly. Fourth, virus species taxonomy should be based on the phylogenetic relationship of a key viral gene (e.g., the RdRp gene of Bunyavirales), which is important for the taxonomy of virus recombinants or reassortants. Fifth, a virus can be demarcated without a species before its biomedical significance has been revealed. Sixth, names of all viruses and virus species should be constituted exclusively with common characters (English letters and Arab numbers), to minimize difficulty in spelling and communication. These proposals are rational, flexible, and can accommodate all known viruses. They can also bridge the taxonomy history and the future demands due to their flexibility.

Thought runs through the mind like blood runs through our body to keep us alive. Like the mind, the body does not stay inert and is in constant motion. Not a single cell in our body is left inert unless cell is under stress or dying. These scenarios are reflected upon when a person is sick, the person lies in bed with less movement; however, is active when the person is healthy. The topic of mechanical stimulation has emerged due to the increasing understanding of the physical stimulations we face each day. Further understanding of the mechanically-regulated mechanism can help us explore the pathological events in a disease. Here, we reviewed the role of sensory proteins in pathological events that are observed in cardiomyopathy, cancer, respiratory, renal, obesity, genetics, physical injury and bacterial infection. Taken together, sensory proteins are mechanically-activated which assist reception of external physical stimulation and convert into biochemical to trigger intracellular signaling cascade.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

The integration of nature-based solutions into land use optimization has emerged as a focal point of current research, primarily due to its efficacy in mitigating flooding impacts and fostering sus-tainable development in both urban and rural areas. Utilizing Shanghai Pujiang Country Park as a case study, this paper conducts a simulation analysis to assess the flood mitigation effectiveness of three distinct land use patterns (Natural scenario, Scenario N; Complete urbanization scenario, Scenario U; Country Park Planning scenario, Scenario P) under five stormwater scenarios with re-turn periods of 2, 5, 10, 20, and 50 years. The findings reveal that Scenario P exhibits superior flood mitigation performance, particularly under stormwater scenarios with a return period of less than 50 years. Building upon these results, the paper proposes recommendations for optimizing land use with a focus on mitigating the impact of flooding. This study is crucial for comprehending the mechanisms involved in urban stormwater logging mitigation through land use methods and holds significance for decision-making in land use and planning at the micro level.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

During prolonged standing, insufficient calf muscle pumping accompanies venous stasis and hypertension in the lower legs, resulting in valve dysfunction, venous wall problems, and subsequent inflammation. Compression therapy, which includes medical compression stockings (MCS) and mechanical intermittent pneumatic compression (IPC), is one of the most effective therapeutic interventions for treating chronic venous diseases. This study aimed to investigate the safety and efficacy of IPC and MCS, and the optimal protocol of compression therapy for chronic venous disease. This crossover trial was conducted for healthy, long standing workers (>8 h daily) with leg edema and pain. Four groups were established for each visit: group A (resting after work without MCS), group B (resting after work with MCS), group C (IPC after work without MCS), and group D (IPC after work with MCS). The primary outcome was the visual analogue scale (VAS) score for leg pain. The secondary outcomes were leg volume (mL), circumference (cm), extracellular fluid/total body fluid (ECF/TBF), and extracellular water/total body water (ECW/TBW) through bioimpedance analysis. Outcomes were assessed before work (T0), after work (T1), and 60 minutes after intervention (T2). We included 39 healthy volunteers, aged 30.03±7.56 years. All four groups had significantly increased leg pain after work (T0-1) but improved 60 minutes after intervention (T1-2), particularly group C (decreased VAS by 1.9). When leg swelling was compared at T0 and T1, groups A and C showed significant increases in leg volume and circumference, indicating significant work-induced edema, whereas groups B and D showed no change or even a decrease. After interventions, leg volume and circumference significantly decreased in groups A and C, although groups B and C did not show significant improvement. The ECF/TBF and ECW/TBW of all groups decreased after interventions. Leg pain and edema after prolonged standing in healthy adults were safely and effectively improved by IPC. Although MCS also reduced leg edema immediately after work, it did not show significant improvement in leg pain at T0-1–and T1-2, nor in swelling at T1-2.

The newly established virus family Phenuiviridae in Bunyavirales harbors viruses infecting three kingdoms of host organisms (animals, plants, and fungi), which is rare in known virus families. Many phenuiviruses are arboviruses and replicate in two distinct hosts (e.g., insects and humans or rice). Multiple phenuiviruses, such as Dabie bandavirus, Rift Valley fever phlebovirus, and Rice stripe tenuivirus, are highly pathogenic to humans, animals, or plants. They impose heavy global burdens on human health, livestock industry, and agriculture and are research hotspots. In recent years the taxonomy of Phenuiviridae has been expanded greatly, and researches on phenuiviruses have made significant progress. With these advances, this review drew a novel panorama regarding the biomedical significance, distribution, morphology, genomics, taxonomy, evolution, replication, transmission, pathogenesis, and control of phenuiviruses, to aid researchers in various fields to recognize this highly adaptive and very important virus family.

In order to make full use of the complementarity of existing navigation systems to improve the navigation and positioning accuracy, this paper investigates the visual/INS integrated navigation system based on the factor graph optimization (FGO) algorithm. In the traditional visual/INS integrated navigation system, there is often the problem of image blurring due to the rapid change of light and shadow captured by the vision sensor and the attitude change of the carrier, which leads to the decrease of the positioning accuracy of the combined navigation system. Therefore, this paper firstly introduces Retinex algorithm and BID algorithm to carry out the design of image de-blurring method; then implements the visual/INS integrated navigation algorithm based on the factor graph optimization method; finally, the experimental scheme is designed, comparative experiments are carried out, and the researched method is verified by using the public dataset. The experimental results show that the combined navigation algorithm realized in this paper has high accuracy, and its positioning accuracy is improved by 40% compared with visual positioning.

In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.

Regeneration of biological tissues in medicine is challenging, and 3D bioprinting offers an innovative way to create functional multicellular tissues. One common way in bioprinting is bioink which is one type of the cell-loaded hydrogel. For clinical application, however, the bioprinting still suffers from satisfactory performance, e.g. in vascularization, effective antibacterial, immunomodulation and regulation of collagen deposition. Many studies have incorporated different bioactive materials into the 3D printed scaffolds to optimize the bioprinting. Here, we review a variety of additives added to the 3D bioprinting hydrogel. The underlying mechanisms and methodology for biological regeneration are important and will provide useful basis for future research.

Reactions of Co(OAc)24H2O, N‚N'-bis(3-pyridylmethyl)oxalamide (L) and 4,4’-sulfonyldibenzoic acid (H2SDA) afforded four coordination polymers with the same mixed ligands, {[Co(L)(SDA)(H2O)2]·H2O·CH3OH}n, 1, {[Co(L)0.5(SDA)]·2H2O·0.5L}n, 2, {[Co(L)1.5(SDA)(H2O)]·H2O}n, 3, and {[Co2(L)1.5(SDA)2(H2O)2]·4H2O}n, 4, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 are 2D layers, revealing the topologies of sql, 2,6L1, (4,4)Ia and 6L12, respectively, and demonstrating that the metal to ligand ratio, solvent system and reaction temperature are important in determining the structural diversity. Immersion of these complexes into various solvents show that the structural types govern the chemical stabilities of 1 – 4. Reversible structural transformation can be shown for complexes 1 and 2 upon solvent removal and adsorption, while those of 3 and 4 are irreversible.

Many countries have implemented free early childhood education to solve the affordability and accessibility problems without considering the sustainability of policy; thus, they have to discontinue the policy. The city of Nanjing, China, is no exception. This case study adopted a mixed-methods approach to understanding how and why the policy was formulated, implemented, and failed in the city, using the “policy cycle” framework. Altogether 232 kindergarten principals and teaching/research staff were randomly sampled and surveyed, and 5 kindergarten principals and 5 teaching/researcher staff were interviewed. The results indicated that there were many obstacles to the policy’s sustainability, including the conflict of interest, the inefficient policy implementation, the insufficient funding, and more social inequality issues. And the policymakers made mistakes in the five domains of the policy cycle: the context of influence, the context of policy text production, the context of practice, the context of outcomes, and the context of political strategy. Finally, the lessons for a more sustainable policy decision process are discussed.

Three monoruthenium complexes 1(PF6)23(PF6)2 bearing a N(CH3)-bridged ligand have been synthesized and characterized. These complexes have a general formula of [Ru(bpy)2(L)](PF6)2, where L is a 2,5-di(N-methyl-N-(pyrid-2-yl)amino)pyrazine (dapz) derivative with various substituents and bpy is 2,2′-bipyridine. The photophyscial and electrochemical properties of these compounds have been examined. The solid-state structure of complex 3(PF6)2 is studied by single crystal X-ray analysis. These complexes show two well-separated emission bands centered at 451 and 646 nm (max = 195 nm) for 1(PF6)2, 465 and 627 nm (max = 162 nm) for 2(PF6)2, and 455 and 608 nm (max = 153 nm) for 3(PF6)2 in dilute acetonitrile solution, respectively. The emission maxima of the higher-energy emission bands of these complexes are similar, while the lower-energy emission bands are dependent on the electronic nature of substituents. These complexes display two consecutive redox couples owing to the stepwise oxidation of the N(CH3)-bridged ligand and ruthenium component. In addition, density functional theory (DFT) and time-dependent density functional theory (TD-DFT) calculations are carried out to elucidate these experimental findings.

Previous study demonstrated the reconstituted type I collagen matrix extracted from rabbit tendons enabled to regenerate the TMJ disc in the rabbit. The aim of this study was to investigate changes in the extracellular matrix (ECM) and mechanisms of regeneration in TMJ disc. In 36 New Zealand rabbits that underwent a partial discectomy, discs were replaced with reconstituted collagen templates for 3 months. A histological analysis showed that moderate to severe degeneration appeared in partially discectomized joints without implantation. In contrast, discs that received the reconstituted collagen template regenerated, and returned to normal to protect the joint. Cells in the regenerative tissue expressed ECM, and fibers became regular and compact due to tissue remodeling over time. Reparative cells differentiated into chondroblasts, and showed highly dense pericellular fibers. The morphology and collagen composition of the disc and condyle in the 3-month experimental group were similar to those of normal tissues. In conclusion, the reconstituted collagen template facilitated the regeneration of surgically discectomized discs. Type I and type II collagens play a crucial role in the regeneration of articular discs.

Metasurface constitutes one of the most promising technologies for holographic imaging; however, the work for terahertz (THz) metasurface holographic imaging is relatively limited. Here, we propose a THz dielectric geometric-propagation phase metasurface, which can operate dual-mode (reflection and transmission) and reconfigurable multifunctional holographic imaging. The dual-mode is realized by controlling the Fermi energy level (Ef) of the graphene integrated into the metasurface unit, and the reconfigurable three-channel holographic imaging in reflection or transmission mode are achieved by switching the feed polarization among left-handed circular polarization (LCP), right-handed circular polarization (RCP) and linear polarization (LP). The metasurface is designed based on the transmission mode, and a physical model for switching to the reflection mode is established. For the first time to the best of our knowledge, a reflection-transmission dynamic modulation THz holographic imaging metasurface has been developed. The holographic metasurface operates in transmission mode at Ef = 0.1 eV, and in reflection mode at Ef = 0.9 eV. Compared with recently published holographic imaging metasurfaces, the proposed metasurface offers the following advantages: high holographic efficiencies (42.5% to 49%), more holographic imaging channels, dynamic modulation dual-mode operations, and reconfigurability.

The process of preparing anti-glare thin films by spray-coating silica sol-gel to soda-lime glass was exclusively and statistically studied in this paper. The effects of sol-gel deliver pressure, air transport pressure, and spray gun displacement speed on the gloss, haze, arithmetic mean surface roughness, and total transmittance light were analyzed. The experimental results indicate that the factors of sol-gel deliver pressure, air transport pressure, and displacement speed exhibit significant effect on the haze, gloss, and Ra. In contrast, the variation of total transmittance light with these three factors are insignificant. Because the anti-glare property is predominantly determined by low gloss and high haze, therefore, we aim to minimize gloss and maximize haze to achieve high anti-glare. Central composite design and response rurface methodology are employed to analyze the main and interaction effects of the three factors through quadratic polynomial equations, which are confirmed by the analysis of variance and R². The response surface methodology predict the lowest gloss and highest haze are 9.2 GU and 57.0%, corresponding to the sol-gel deliver pressure, air-transport pressure, and displacement speed of 250 kPa, 560 kPa, and 140 mm/s, and 340 kPa, 620 kPa, and 20 mm/s, respectively. Comparing the predicted optimal data with the real experimental results validates the applicability of the mathematical model. This study provides an important basis for the subsequent production of anti-glare glass with different specifications to satisfy the market demand.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

Tourism activities generally have a ∩-type lock on the level of tourism ecological security in an area, but when applied to the border areas of China, there are certain specificities in the spatial evolution of tourism ecological security (TES) compared to traditional findings. This paper measures tourism ecological security in China’s border areas from 2009 to 2020 by using the DPSIR model with the superefficient SBM-DEA and analyzes the spatial differences, evolutionary characteristics, and driving factors of tourism ecological security in border areas by using Pearson’s correlation coefficients, center of gravity models, and geographic probes: (1) The overall tourism ecological security index of China’s border provinces is relatively good. Tourism activities do not completely affect the traditional “∩ lock” of the border provinces. The tourism ecological security level of the border provinces presents three spatial-temporal changes (“∩” type, “U” type, “\” type) and four evolution trends (“high–high–high”, “middle–middle–medium”, “medium–low–low”, and “low–low–low”). (2) The overall tourism ecological security level in border areas is polarized between high and low levels, and the ecological security efficiency of the three large areas is spatially characterized as “Southwest Area > Northeast Area > Northwest Area”, and the center of gravity of ecological security is mostly concentrated in Xinjiang, Tibet, and Neimenggu, where the ecological security level is higher. (3) Social and environmental factors are the main factors that influence tourism ecological security in border areas, while economic factors account for a smaller proportion. Accordingly, this thesis also proposes the driving mechanism of the ecological security of tourism sites in border areas in China with a view to providing theoretical support for policy formulation.

The rapid development of China's economy has led to a rapid increase in energy production and use. Among them, the excessive consumption of coal in fossil energy consumption is the leading cause of air pollution in China. This paper incorporates renewable energy innovation, fossil energy consumption and air pollution into a unified analysis framework, and uses spatial measurement models to investigate the spatial effects of renewable energy green innovation and fossil energy consumption on air pollution in China, and decomposes the total impact into direct and indirect effects. influences. The empirical results show that China's air pollution, renewable energy green innovation and fossil energy consumption are extremely uneven in geographical space, generally showing the characteristics of high in the east and low in the west, and showing a strong spatial aggregation phenomenon. Fossil energy consumption will lead to increased air pollution, and the replacement of fossil fuels with clean and renewable energy is an important means of controlling pollution emissions. The direct and indirect effects of renewable energy green innovation on air pollution are significantly negative, indicating that renewable energy green innovation not only suppresses local air pollution, but also suppresses air pollution in neighboring areas. The consumption of fossil energy will significantly increase the local air pollution, and the impact on the SO2 and Dust&Smoke pollution in the adjacent area is not very obvious. It is recommended to strengthen investment in renewable energy green innovation, reduce the proportion of traditional fossil energy consumption, and pay attention to the spatial connection and spillover of renewable energy green innovation.

With the increase of global human activities, a large number of technogenic magnetic particles (TMPs) generated by industrial activities such as coal combustion, traffic and so on enter sediments on continental shelves. However, there is currently a lack of understanding of the spatiotemporal distribution of TMPs on continental shelves, as well as the sedimentary effects they cause. This review work comprehensively analyzes the source, morphology, composition, and spatiotemporal distribution characteristics of TMPs. Then it elucidates their magnetic contribution to sedimentary environments in continental shelf seas, as well as the influence of heavy metals and active iron. At the same time, the existing problems and future development directions of TMPs on continental shelves are summarized.

The author’s opinion is that the negative energy solutions of the Dirac equation mean that a particle can be of negative kinetic energy (NKE) besides positive kinetic energy (PKE). We think that NKE particles are dark ones and NKE matter is dark matter. In our previous works, the dark matter theory of the NKE version and the dark energy theory that matched dark matter theory were put forth. In this work, we investigate the topics related to the metamorphosis of objects between PKE and NKE. We first evaluate the collosions between a PKE and a NKE particles. A scenario of accelerating PKE particles is raised. We put forth the cosmic dark radiation background and gravity potential background. In the universe, negative energy is predominating. In the observable universe, substances constitute stable PKE systems. The total energy of every such system is negative. We propose a mechanism that NKE substances combine into stable PKE systems. Macroscopically, NKE objects can constitute stable PKE astrophysical systems by means of gravity between them. Microscopically, NKE particles can combine into stable PKE systems by means of attractive interactions between them, say, Coulomb attraction. Currently, people think that there are four ingrediants in the universe: photons \Omega_R0, matter \Omega_M0, dark matter \Omega_DM, and dark energy \Omega_\lambda0. We analyze the order of the appearance of the four ingredients and conclude that qualitatively, their proportions should be \Omega_\lambda0 > \Omega_DM > \Omega_M0 > \Omega_R0.

Acute lymphoblastic leukemia is the most common malignancy in children and is characterized by numerous genetic and epigenetic abnormalities. Epigenetic mechanisms, which involve DNA methylations and histone modifications, result in the heritable silencing of genes without a change in their coding sequence. Emerging studies are increasing our understanding of the epigenetic role of leukemogenesis and have demonstrated the potential of DNA methylations and histone modifications as a biomarker for lineage and subtypes classification, predicting relapse, and disease progression in ALL. Epigenetic abnormalities are relatively reversible when treated with some small molecule-based agents compared to genetic alterations. In this review, we conclude the genetic and epigenetic characteristics in ALL and discuss the future role of DNA methylation and histone modifications in predicting relapse, finally focus on the individual and precision therapy targeting epigenetic alterations.

The open burning of sugarcane residue is commonly used as a low-cost and fast method during pre-harvest and post-harvest periods. However, this practice releases various pollutants, including dioxins. This study aims to predict polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs, or dioxins) emissions using the Grey Model (GM (1,1)) and to map the annual flux spatial distribution at the provincial level from 2023 to 2028. Using the activity rate of dry crop residue from national agencies and literature, and following the guidelines set by the United Nations Environment Programme (UNEP), an annual emission inventory was developed at the provincial level. The distribution of emissions from 2016 to 2022 was then mapped. The average PCDD/Fs emission values exhibit significant variation among the provinces, averaging 309 pg TEQ/year. Spatially, in line sugarcane production, South Sumatra and East Jawa consistently show high emissions, often exceeding 400 pg/m². Emissions based on the UNEP emission factor tend to be higher compared to other factors, due to its generic nature and lack of regional specificity. The emission predictions using the Grey Model GM (1,1) indicate that North Sumatra is expected to experience a steady increase in PCDD/Fs emissions, whereas South Sumatra and Lampung are projected to see a slight decline. This forecast assumes there will be any changes in regional intervention strategies. Most regions in Jawa Island show a gradual increase in emissions, except for East Jawa, which is predicted to have a slight decline from 416 pg/year in 2023 to 397 pg/year in 2028. Additionally, regions like Gorontalo and parts of East Jawa are projected to remain "hotspots" with consistently high emissions, suggesting the need for targeted interventions. Future studies should consider developing monthly emissions profiles to account for local agricultural practices and seasonal conditions. The emission data generated in this study, which includes both spatial and temporal distributions, is valuable for air quality modeling studies. Utilizing this data can help assess the impact of current and future emissions on ambient air quality.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

Based on previous research results, we propose a new preprocessing HSS iteration method (PHSS) for the generalized Lyapunov equation. At the same time, the corresponding inexact PHSS algorithm (IPHSS) is given from the angle of application. All the new methods presented in this paper have given the corresponding convergence proof. The numerical experiments are carried out to compare the new method with the existing methods, and the improvement effect is obvious. The feasibility and effectiveness of the proposed method are proved from two aspects of theory and calculation.

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

An improved synthesis of glucosyl esters was reported here, avoiding the use of expensive Ag reagent as well as the hydrolysis of instable glucosyl bromide. Notably, ß-configuration product was exclusively obtained in good yield.

A spinning gyroscope precesses about the vertical due to a torque acting upon the wheel. The torque is generated by the shift of moment of force by gravity and it points to the vertical instead of the tangential direction of precession. This intuition offers an alternative and straightforward view of precession dynamics in comparison with the literature. It also presumes a dynamic balance of momentum between circular motions of the wheel spin and precession. Accordingly, the gyroscopic dynamics is then applied to the study of galactic motion of the solar system in space and the Galactic mass is calculated with the inclusion of gyroscopic effect of the solar planets. Results indicate that the gyroscopic effect of Mercury orbiting around the Sun can increase the calculated Galactic mass by 23% in comparison with the result obtained by the classic approach.

Ship detection in large-scene offshore synthetic aperture radar (SAR) images is crucial in civil and military fields, such as maritime management and wartime reconnaissance. However, the problems of low detection rates, high false alarm rates, and high missed detection rates of offshore ship targets in large-scene SAR images are due to the occlusion of objects or mutual occlusion among targets, especially for small ship targets. To solve this problem, this study proposes a target detection model (TAC_CSAC_Net) that incorporates a multi-attention mechanism for detecting marine vessels in large-scene SAR images. Experiments were conducted on two public datasets, the SAR-Ship-Dataset and high-resolution SAR image dataset (HRSID), with multi-scene and multi-size, and the results showed that the proposed TAC_CSAC_Net model achieves good performance for both small and occluded target detection. Experiments were conducted on a real large-scene dataset, LS-SSDD, to obtain the detection results of subgraphs of the same scene. Quantitative comparisons were made with classical and recently developed deep learning models, and the experiments demonstrated that the proposed model outperformed other models for large-scene SAR image target detection.

The compatibility of graphene or graphene oxide with its dispersion medium (polymer) plays a critical role in the formation nanocomposite materials with significant property improvements. Environmentally friendly miniemulsion polymerization, which allows a formation of nanoencapsulation in an aqueous phase and high molecular weight polymer/composite production is one promising method. In this study, we screened a series of amphiphilic modifiers and found that the quaternary ammonium (ar-vinyl benzyl) trimethyl ammonium chloride (VBTAC) pending carbon double bonds could effectively modify the graphene oxide (GO) to be compatible with the organophilic monomer. After that, free radical miniemulsion polymerization could successfully synthesize stable latex of exfoliated poly (methyl methacrylate) (PMMA)/ GO nanocomposite. The final latex had an extended storage life and a relatively uniform particle size distribution. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) analysis of this latex and its films indicated successful encapsulation of exfoliated nano-dimensional graphene oxide inside a polymer matrix.

Impervious surface mapping with high-resolution remote sensing imagery has attracted increasing interest as it can provide detailed information for urban structure and distribution. Previous studies have suggested that the combination of LiDAR data and high-resolution imagery for impervious surface mapping performs better than using only high-resolution imagery. However, due to the high cost of the acquisition of LiDAR data, it is difficult to obtain the multi-sensor remote sensing data acquired at the same acquisition time for impervious surface mapping. Consequently, real landscape changes between multi-sensor remote sensing data at different acquisition times would lead to the error of misclassification in impervious surface mapping. This issue has mostly been neglected in previous works. Furthermore, the observation differences generated from multi-sensor data, including the problems of misregistration, missing data in LiDAR data, and shadow in high-resolution images would also challenge the final mapping result in the fusion of LiDAR data and high-resolution images. In order to conquer these problems, we propose an improved impervious surface mapping method incorporating both LiDAR data and high-resolution imagery at different acquisition times in consideration of real landscape changes and observation differences. In the proposed method, a multi-sensor change detection by supervised multivariate alteration detection is employed to obtain changed areas and misregistration areas. The no-data areas in the LiDAR data and the shadow areas in the high-resolution imagery are extracted by independent classification yielded by its corresponding single sensor data. Finally, an object-based post-classification fusion is proposed to take advantage of independent classification results with single-sensor data and the joint classification result with stacked multi-sensor data. Experiments covering the study site in Buffalo, NY, USA demonstrate that our method can accurately detect landscape changes and obviously improve the performance of impervious surface mapping.

For solving the fractional differential equations in computational fluid dynamics (CFD), it’s complicated and difficult by the Laplace and Fourier transforms. Based on the Caputo fractional derivative, the analytical solutions for unsteady unidirectional flows of a generalized Oldroyd-B fluid are deduced by the separation of variables method. Results show that the analytical solutions are given easily, and have good university. For some specific parameter values, the well-known analytical solutions for the generalized second grade fluid, the generalized Upper-Convected Maxwell (UCM) fluid as well as the ordinary Oldroyd-B fluid can be obtained.

In this study, the decision-making process management of forest tending in the forestry business is decentralized, and forest tending decision-making activities at different points in time are integrated by decision makers at different geographical locations. The decision-making process was analyzed and optimized from a system perspective. Based on the optimized decision-making process, a forest tending business group decision support system (FTGDSS) was established. We first reviewed and discussed the characteristics and development of the forest tending business and forestry decision support system. Business Process Modeling Notation was used to draw a current state flow chart of the forest tending business, to identify and discover important decision points in the process of tending decision-making. We also analyzed the content and attributes of each decision point, and described the system structure, functional framework, knowledge base structure, and reasoning algorithm of FTGDSS in detail. Finally, FTGDSS was evaluated from the two dimensions of the technology adoption model. FTGDSS integrates different levels of time-space decision-making activities, historical tending data, business plans, decision-makers' management tendencies into the decision-making process and automatically extracts decision-making data from the forest business process management enterprise resource planning system (Smartforest) that improves the ease of use of the decision support system (DSS). It also improves the quality of forest tending decisions, and enables the DSS to better support multi-target management strategies.

Raman spectroscopy is a type of inelastic scattering that provides rich information about a sub-stance based on the coupling of the energy levels of their vibrational and rotational modes with incident light. It has been applied extensively in many fields. As there is an increasing need for remote detection of chemicals in planetary exploration and anti-terrorism, it is urgent to develop a compact and easily transportable fully automated remote Raman detection system for trace detection and identification of information with high-level confidence about the target’s compo-sition and conformation in real-time and for real field scenarios. Here, we present an unmanned vehicle-based remote Raman system, which includes a 266 nm air-cooling passive Q-switched nanosecond pulsed laser of high-repetition frequency, a gated ICMOS, and an unmanned vehicle. This system obtains good spectral signals from remote distances ranging from 3 m to 10 m for simulating realistic scenarios, such as aluminum plate, woodblock, paperboard, black cloth, and leaves, and even for detected amounts as low as 0.1 mg. Furthermore, a CNN-based algorithm is implemented and packaged into the recognition software to achieve fast and more accurate de-tection and identification. This prototype provides a proof-of-concept for an unmanned vehicle with accurate remote substance detection in real-time, which can be helpful for remote detection and identification of hazardous gas, explosives, their precursors, and so forth.

This study explores the relationship between mental and physical therapeutic through three dimensions: man-environment relationships; a sense of place and symbolic landscapes. The study used a combination of qualitative and quantitative research methods. Local residents living in the coastal area of Xinglin Bay are the research objects. Quantitative data analysis revealed that the frequency of residents' visits was an important variable affecting their physical and treatment perceptions. In addition, the significance is higher for females than for males. The text analysis shows that the environment, especially the ecological restoration of water quality and migratory birds, is of great significance to the identity of local residents. Daily activities contribute to a sense of place and are what make the coast a place of therapeutic landscape function.

The phenomenon of interference is a characteristic of all waves. This paper reviews the interference of classical waves and of matter waves in quantum mechanics. In quantum mechanics, there are two interference mechanisms between identical particles. One is that the de Broglie wavelengths of two interference waves are the same, which is called the equal wavelength interference mechanism. The other is that the wavelengths of interference waves can also be different, in which case there should be an exchange term in additional to the direction term in the wave function. There is a fixed phase difference between the two terms, which causes interference. This is called exchange effect interference mechanism. We propose an experiment, which is simpler to what has been done, to show the exchange effect interference. There is a special case where two interference waves can satisfy both the two mechanisms. We propose an experiment to discriminate that in this case which mechanism plays a role on earth.

People have long had a problem: the equations of motion that reflect the laws of physics are invariance under time inversion, while there always are irreversible processes for gases compose of microscopic particles. This article solves this problem. The point is that we should distinguish between the concepts of the equation of motion and motion. We also need to distinguish between the concepts of time-inverse motion and reverse motion. The former is anticlockwise, which is a frictional motion, while the latter is clockwise. For the single-particle motions in classical mechanics and in quantum mechanics, we present mathematical expressions for time-inversion motion and reverse motion, respectively. We demonstrate that single-particle motion is irreversible. The definition of the reversibility of two-particle collisions is given. According to the definition, the two-particle collision as a microscopic motion processes is irreversible. Consequently, for a gas consisting of a large number of particles colliding with each other, its movement should be irreversible, unless the condition of detailed balance is met. We give a physical explanation for the detailed balance, which does not concern the meaning of microscopic reversibility. The detailed balance means that after a pair of reciprocal collisions occur, the distribution function of the particles remains unchanged. Therefore, microscopic two-particle collision events are irreversible, but the statistical average of a large number of collision events makes it possible for the macroscopic process of a gas to be reversible. Conclusively, we clarify the microscopic mechanism of the irreversible process of gases.

Up to now, Schrödinger equation, Klein-Gordon equation (KGE) and Dirac equation are believed the fundamental equations of quantum mechanics. Schrödinger equation has a defect that there is no NKE solutions. Dirac equation has positive kinetic energy (PKE) and negative kinetic energy (NKE) branches. Both branches should have low momentum, or nonrelativistic, approximations: one is Schrödinger equation and the other is NKE Schrödinger equation. KGE has two problems: it is an equation of second time derivative, and calculated density is not definitely positive. To overcome the problems, it should be revised as PKE and NKE decoupled KGEs. The fundamental equations of quantum mechanics after the modification have at least two merits. They are of unitary in that everyone contains the first time derivative and are symmetric with respect to PKE and NKE. This reflects the symmetry of the PKE and NKE matters, as well as matter and dark matter, of our universe. The problems of one-dimensional step potentials are resolved by means of the modified fundamental equations for a nonrelativistic particle.

This research develops the Osteoporosis Knowledge, Attitude, and Behaviors Questionnaire (OKABQ) with the intent to evaluate levels of osteoporosis knowledge, attitude and behavior change. The aims of the study were to develop and validate the OKABQ; and to establish a mediation model of the research. A quantitative, descriptive, and instrumental study was conducted in two phases: Phase I—development of the scale through Delphi Method by osteoporosis experts; Phase II—evaluation of the validity and reliability of the scale and construction of a mediation model using SmartPLS. In Phase I, the content validity index (CVI) of the questionnaire was higher than 0.96 and the inter-rater reliability (IRR) kappa was 1.00. In Phase II, exploratory factor analysis showed that two predominating factors of attitude as a mediation were addressed by the 26-item OKABQ. The indirect effect results from the estimated model indicates that attitude mediates the relationship between knowledge and behaviors (β = 0.114, t = 2.627, p < 0.001), which is positive and statistically significant. We concluded that the OKABQ is a valid measure of osteoporosis knowledge, attitude and behaviors for women with osteoporosis. These assessment results could assist healthcare providers in mitigating insufficiency on health education.

This research aims to study the ultimate limit state (ULS) behaviour of stiffened panel under longitudinal compression by non-linear finite element method (NLFEM). There are different types of stiffeners being used in shipbuilding i.e. T-bar, flat-bar and angle-bar. However, this research focuses on the ultimate compressive strength behaviour of flat-bar stiffened panel. A total of 420 of reliable scenarios of flat-bar stiffened panel are selected for numerical simulation by ANSYS NLFEM. The ultimate strength behaviours obtained were used as data for the development of closed form shape empirical formulation. Recently, Kim et al. [1] proposed for advanced empirical formulation for T-bar stiffened panel and the applicability of the proposed formulation to flat-bar stiffened panel will be confirmed by this study. The accuracy of the empirical formulation obtained for flat-bar stiffened panel has been validated by FE simulation results of statistical analysis (R2 = 0.9435). The outcome obtained will be useful for ship structural designers in predicting the ultimate strength performance of flat-bar type stiffened panel under longitudinal compression.

Forest-grass intercropping patterns of protected cultivation has been widely used to increase productivity and sustainability in modern agriculture. However, there have been few studies of wolfberry (L. barbarum) intercropping and it is cultivated mostly by clean tillage. This paper takes 10 kinds of wolfberry-forage intercropping patterns, compares the effects of different planting modes on the growth, yield, photosynthetic characteristics, nutritional quality, and the degree of occurrence of diseases and pests, which aims to make clear the effects of wolfberry-forage intercropping patterns on wolfberry. The results showed that different intercropping combinations had different effects on wolfberry. The overall effect of Wolfberry-forage intercropping patterns on the growth of wolfberry were promote the photosynthetic characteristics. Ryegrass could increase the branch number, Lvyuan 5 and mangel increase branch length; Mangel, clover, sweet sorghum, ryegrass and stipas could reduce the damage of powdery mildew by 69%, and alfalfa, stipa and ryegrass could reduce the occurrence of aphids by 67% (P<0.05). Intercropping could increase carotenoids, flavonoids and ascorbic acid contents to improve wolfberry quality by 21%, 53% and 127%, respectively (P<0.05). Among all the performances, wolfberry-mangel intercropping has absolute advantages in promoting wolfberry yield and quality increase. Therefore the best patterns of wolfberry-mangel, wolfberry-ryegrass, wolfberry-alfalfa and wolfberry-clover were chosen.

Celtis sinensis is an adaptable species that is widely grown in southern China. In June 2022, a leaf blotch disease of C. sinensis was observed in Nanjing, Jiangsu, China. Based on morphological characterization, three isolates were identified as Alternaria species. Phylogenetic analysis of combined ITS, GAPDH, TEF1-α, RPB2 and Alt a 1 sequences identified the three isolates we obtained as Alternaria alternata and Alternaria koreana. Koch’s postulates were fulfilled in the greenhouse, and the pathogenicity of A. alternata and A. koreana was determined by leaf inoculation tests on C. sinensis seedlings. The symptoms of indoor inoculation were consistent with those in the field. A. alternata and A. koreana can grow at 15-35 °C, with an optimal growth temperature of 25 °C. The results of fungicide sensitivity experiments indicated that A. alternata and A. koreana were the most sensitive to prochloraz, which may be a useful strategy for the future prevention and control management of A. alternata and A. koreana. This study provides the first step for further research on A. alternata and A. koreana as pathogens of C. sinensis and provides a theoretical basis for future control strategies.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

This experiment was conducted to study the effects of Cyfluthrin (Cy) exposure on neurobehaviour, hippocampal tissue and synaptic plasticity in Wistar rats. First, high-dose Cy exposure can cause nerve injury with symptoms such as deficits in learning and memory ability, spatial exploration and autonomic motor ability. Moreover, it was found that medium- and high-dose Cy exposure can cause disordered energy metabolism in hippocampal cells and an abnormal release of the neurotransmitter Glu. Second, pathological brain sections showed that the middle and high doses of Cy caused deformation, reduction and disorder of hippocampal pyramidal cells, a decrease in the number of Nissl bodies, pyknosis of the hippocampal cell nuclear membrane and serious damage to organelles, indicating that exposure to these doses of Cy may cause hippocampal tissue damage in rats. Third, with the increase in exposure dose, the morphological changes in hippocampal synapses were more obvious, including blurred synaptic spaces, decreased synaptic vesicles and a decreased number of synapses. Moreover, the expression levels of the key synaptic proteins PSD-95 and SYP also decreased in a dose-dependent manner, indicating obvious synaptic damage. Finally, the study found that medium and high doses of Cy could upregulate the expression of A2AR in the hippocampus, and the expression levels of inflammatory factors and apoptosis-related proteins increased in a dose-dependent manner. Moreover, the expression of A2AR mRNA was correlated with neurobehavioural indicators, inflammatory factors, synaptic plasticity factors and apoptosis factors, suggesting that Cy may cause nerve damage in rats and has a close relationship with A2AR.

In recent years, the AHRS has become an important research area. In order to improve the orientation measurement accuracy of AHRS, this paper first expounds the algorithm principle of the AHRS. Then, aiming at the problem of poor stability of the traditional gradient descent method under high dynamics or large magnetic field interference, a gain-scheduled anti-interference AHRS orientation algorithm is designed. By using the switching architecture designed with this algorithm for gain scheduling, it can ensure stable performance while being subjected to apparent acceleration and ferromagnetic interference. Finally, experimental verification is conducted, and the experimental results show that: in the presence of interference, the roll angle error is 0.0350°, the pitch angle error is 0.0277°, and the yaw angle error is 0.9611°, thereby verifying the strong anti-interference performance of the gain-scheduled AHRS orientation algorithm proposed in this paper.

Administration of crude polysaccharides extract from natural product is a promising gut microbiota-targeted approach to preventing obesity and associated metabolic disorders. Dietary restrictions can change the type and number of gut bacteria, which is an important factor in delaying the onset and burden of diseases. This study aimed to investigate the effects of high-yield crude polysaccharides from Cordyceps militaris (CMP) on high-fat diet (HFD) mice model and the gut microbiota community assembly, and to identify whether selenium (Se) addition would improve CMP action mode during cultivation. We found that the CMP treatment ameliorated adipose and liver pathologic morphology and fat accumulation in obese mice, while, SeCMP intervention was not superior than CMP in body mass gain, but notably decreasing serum triglyceride level increased by HFD. The upregulated expression of gene Cyp7a1 in liver and protein UCP1 in brown adipose tissue (BAT) preliminary indicated that the effect might relate to bile acids (BAs) metabolism pathway and thermogenesis. In addition, CMP showed a drastic decrease in the gut microbes which positively correlated with dyslipidemia parameters. Our result reveals the potential of CMP to be used as functional food in the prevention of diet-induced adipose and liver steatosis, so does SeCMP has outstanding capacity of improving dyslipidemia.

Background: Cancer patients require cross-professional care during the diagnosis and treatment periods. Therefore, methods for effectively carrying out case management are essential to tumor care. Purpose: To investigate the effects of using the community software LINE Official Ac-count on oral cancer case management. Methods: An experimental design was used; 100 patients were randomly divided into two groups by using a computer-generated random number table. The experimental group used LINE Official Account, which gave them self-care information, timely messages, and one-on-one health-care consultations. The control group followed standard healthcare practices. Results: The experimental group was satisfied with the self-care information provided by LINE Official Account (86.9%), patients regularly checked the self-care information (89.4%) and would check the information when receiving a push notification (54.3%). Ten patients used the one-on-one consultation(20.0%). LINE Official Account had a significant effect on the rate of participation in support groups. Generalized estimating equations indicated a significant difference between the two groups regarding the overall quality of life over 7 days (P = 0.023). Conclusion: Community software applications used in oncological case management can improve self-management and empower, also enable tracking of long-term follow-up effectiveness and reinforce the case manager’s role as a family therapist. Therefore, this study recommends that case manager systems be incorporated into mobile applications to increase the sustainable management, accessibility, effectiveness, and satisfaction of oncological management systems. This study also provides the value of Sustainable Development Goals (SDGs) with Good Health and Well-being, and decreased social withdrawal among patients with oral cancer.

This article explores the relationship between Wang Yangming's philosophy and the new quality productivity, revealing how the new quality productivity, while inheriting the core ideas of Yangming's philosophy, achieves a higher level through innovation and development. The new quality productivity emphasizes the integration and innovation of knowledge, technology, and information, characterized by knowledge-driven innovation, information technology support, sustainable green development, and global collaborative development. The fusion of Yangming's philosophy and the new quality productivity holds significant theoretical and practical implications.

Two 2,2':6',2''-terpyridine-based Schiff bases (TPySSB and TPySB) have been synthesized. The TPySSB shows remarkable selective ‘off-on’ fluorescence for Al³⁺ by photoinduced electron transfer (PET) mechanism of sensing. Chemosensor TPySSB binds Al³⁺ in a 1:2 ratio with an association constant 6.8×10⁵ (R²=0.98) and this 1:2 stoichiometric model is established on Job’s plot and ¹H NMR. Compared TPySSB and TPySB, it is of great importance of the existence of salicylidene unit due to its strong binding abilities of both phenol and C=N structure to the Al³⁺.

The epidemic of Coronavirus Disease 2019 (Covid-19) has brought many changes to people's life. This study aims to analysis Chinese people's psychological change and life after quarantining Wuhan and explore the influencing factors. Based on data from a web-survey after quarantining Wuhan (N=3268), the principal-component-analysis (PCA), multiple-linear-regression (MLR), propensity-score-matching (PSM) were used to explore the psychological change of people in China and the influencing factors. 83.3% of the respondents said that the impact of the epidemic on their life had increased after quarantining Wuhan. A considerable proportion of people's anxiety increased, being reflected in negative emotion, behavioral response and physiological response. The proportion of people who said their anxiety had increased in Wuhan was higher than that in other regions (p <0.05). The anxiety of people who were in medical isolation increased less than those who were not (p <0.05). All three aspects of people’s anxiety were positively related with time of medical isolation and degree of the attention on the epidemic (p＜0.05) except the effect of attention degree on the physiological response (p＝0.06). The measure of medical isolation at home should be advocated. Yet people should reduce the concern for the epidemic while paying attention to self-protection.

Self-sustained learning (SSL) is considered a crucial factor in promoting students’ long-term learning and development in a sustainable society. To deepen the understanding of SSL, especially in the context of learning English as a second language, the current study examined the influence of intercultural communicative skills, language mindset, and positive L2 self on SSL in English learning among 1,238 college students in China. The results showed that students not only had a strong language mindset, positive L2 self, and intercultural communicative skills but also scored higher in long-term self-sustained English learning. Findings from the Structural Equation Modeling indicated that both language mindset and intercultural communicative skills positively predicted positive L2 self and self-sustained English learning. Furthermore, language mindset and intercultural communicative skills had an indirect impact on self-sustained English learning through positive L2 self. These findings suggest that to promote English learners’ SSL, instructors should help facilitate students’ intercultural communicative skills and foster a growth language mindset, as well as positive language learning beliefs.

We fabricated high-quality MAPbBr3 single crystals (SC) by introducing moderate amount electron-rich poly(propylene glycol bis(2-aminopropyl ether) (PEA) additives with an inverse temperature crystallization (ITC) method. The intramolecular vibrations and defective states of prepared MAPbBr3 single crystals were systemically studied by the in situ variable-temperature Fourier Transform Infrared (FTIR) Spectroscopy, X-ray photoelectron spectroscopy (XPS), and the synchrotron-based X-ray absorption near edge structure (XANES), et al. We infer that the proper amount of PEA additives would prevent the formation of intermediate states and crystal boundaries, passivating the density of defective states. The X-ray detection properties of single-crystal MAPbBr3 crystals were investigated, using both high dose and low dose X-ray photons at 40keV in synchrotron beamlines. The photocurrent of optimized PEA-treated MAPbBr3 single crystals demonstrate better performance compared with the as-prepared single crystals. Meanwhile, the decay time of MAPbBr3 single crystal is decreased from 460 ns to 210 ns by Time-resolved photoluminescence (TRPL) decay measurement, owing to the defect passivation by 0.5wt% PEA additives. The PEA-treated single crystals possess much faster decay time than the commercialized Ce:YAG scintillator (>500ns). These results help elucidate the passivation of defective states and contribute paths to manufacture high-quality single crystal perovskites for next-generation optoelectronic devices.

Since the development of CBCT had been utilized in dentistry, the images of the CBCT can assist the surgeon to evaluate the anatomy carefully. Despite the value of the radiology evaluation, the implant procedures may require additional consideration rather than only evaluating the anatomical factors. The purpose of this study is to evaluate the predictability of using CBCT alone to plan for implant placement on the edentulous patient digitally CBCT images were analyzed by clinicians, measuring the ridge heights and widths of 4 selected implant sites in the maxillary and 2 selected implant sites in the mandibular arches for 91 patients planning for the implant-supported overdenture. (A total of 47 patients out of the 91 had completed the implant placement on the edentulous ridge, contributing to 55 upper and/or lower arches (136 dental implants). . Both predictabilities are low, implying the CBCT planning for implant placement on the edentulous ridge is not a good index and is insufficient to predict the surgical procedures as a solo method. The finding of this study indicates that digital planning by CBCT is insufficient to serve as an individual tool to predict implant procedures. Further information and evaluation must be considered for implant placement on the edentulous ridge.

Biological neural network (BNN) is the core brain for creature to accomplish its intelligent behaviors through unique network structure and mechanisms. It also inspires controlling human-designed autonomous agents including robots to generate more advanced intelligent behaviors by mimicking the neural control mechanism of creatures at a deeper and more interactive level. Here, we constructed a whole-brain neural network model of Caenorhabditis elegans (C. elegans), which characterizes the electrochemical processes at the level of cellular synapse. The neural network simulation integrates computational programming and visualization of neurons and synapse connections of C. elegans, containing the specific controllable circuits summarization with their dynamic characteristics within the whole network. To illustrate its particular intelligent control capability in terms of robotics, we introduce the first innovative methodology for applying the BNN model to a 12-legged robot’s movement control based on the established numerical simulation platforms. We accomplished and designed two methods and corresponding encoding processes, one involving orientation control and the other involving locomotion generation, to demonstrate the intelligent control performance of BNN. Both simulation and experiment results indicate that the robot exhibits stronger autonomy and more intelligent moving performance under the control of BNN. We then summarized the contributions for digitalizing the C. elegans’ whole-brain neural network in real-time and utilizing it to control robot in a closed loop to validate its advanced intelligence control ability in terms of a scientific robot.

One of the most leading causes of death worldwide is Colorectal cancer(CRC). Polyp segmentation is the most important detected measure for preventing CRC. However, there is still a missing rate for diminutive polyps and multiple ones. In order to solve the phenomenon, we propose to introduce auxiliary attention module(AAM) that can enhance the learning of features related to multiple and diminutive polyps by focusing more on the located and detailed information. Meanwhile, we design to decrease missed rate of multiple and diminutive polyps by implementing an area adaptive loss(AAL) which adapts the weight according to the area and the number of polyps. Our proposed novel AAM and AAL concentrates on training with hard examples and localized information. To evaluate the effectiveness and generalization ability of our proposed model, We utilize three different datasets of variable sizes and a cross dataset. Our proposed method achieves the best results on the Kvasir-SEG dataset, the CVC-ClinicDB dataset and the cross dataset, particularly for the Kvasir-Sessile dataset consisting of small,flat and diminutive polyps. Extensive experimental results show that our proposed DoubleAANet surpass the performance of all existing state-of-the-art segmentation methods.

In this paper, PEN3 electronic nose was used to detect and recognize fresh and moldy apples (inoculated with Penicillium expansum and Aspergillusniger) taken Golden Delicious apples as model subject. Firstly, the apples were divided into two groups: apples only inoculated with different molds (Group A) and mixed apples of inoculated apples with fresh apples (Group B). Then the characteristic gas sensors of the PEN3 electronic nose that were most closely correlated with the flavor information of the moldy apples were optimized and determined, which can simplify the analysis process and improve the accuracy of results. Four pattern recognition methods, including linear discriminant analysis (LDA), backpropagation neural network (BPNN), support vector machines (SVM) and radial basis function neural network (RBFNN), were then applied to analyze the data obtained from the characteristic sensors, respectively, aiming at establishing the prediction model of flavor information and fresh/moldy apples. The results showed that only the gas sensors of W1S, W2S, W5S, W1W and W2W in the PEN3 electronic nose exhibited strong signal response to the flavor information, indicating were most closely correlated with the characteristic flavor of apples and thus the data obtained from these characteristic sensors was used for modeling. The results of the four pattern recognition methods showed that BPNN presented the best prediction performance for the training and validation sets for both the Group A and Group B, with prediction accuracies of 96.29% and 90.00% (Group A), 77.70% and 72.00% (Group B), respectively. Therefore, it first demonstrated that PEN3 electronic nose can not only effectively detect and recognize the fresh and moldy apples, but also can distinguish apples inoculated with different molds.

Folk residence in the cold region of Northeast China is an important part of China's traditional folk residence, with significant geographical representation. In this paper, we take the residential compounds of villages and towns in the cold region of Northeast China as the research object, summarize four typical layout forms of residential compounds of villages and towns in the cold region of Northeast China, simulate the wind environment of compounds of different layout forms in winter by using the computer numerical simulation software Fluent, and then analyze and evaluate the wind environment of compounds by combining with the evaluation standard of wind speed ratio and considering the area of wind shadows, number of vortices and other factors.

The exponential growth of digital media content has introduced new challenges in managing and classifying internet traffic. Digital media traffic is composed of various applications such as video, audio, social media, and search, and its data structure is complex, incorporating a vast array of features. The classification of traffic data is a crucial aspect of internet traffic management and network security, and it forms the basis for several scenarios, including content distribution, advertising recommendations, and data analysis. Traditional classification methods rely mainly on deep packet inspection and port-based techniques, which have become increasingly ineffective due to the rapid evolution of network traffic. To address this issue, this study proposes a machine learning-based traffic classification method aimed at enhancing the accuracy and efficiency of digital media traffic classification to meet the current needs of traffic management and network security. The paper also analyzes and evaluates the classification effect and prediction capability of various algorithms under different training set sizes to validate the feasibility and effectiveness of the proposed method. The result demonstrates that the neural network algorithm has superior classification and prediction capabilities compared to the decision tree and support vector machine algorithms. Furthermore, our proposed method achieves the highest accuracy of 96.88% with a large training sample of 40,000 data streams, proving its superiority in handling high-dimensional data and complex datasets. The research results are significant for the development of digital media traffic classification and prediction methods and are expected to be applied in practical scenarios.

With the continuous development of Artificial Intelligence technology and Internet of Things engineering, more and more driver-less vehicles have been developed and put into the industrial production. The birth of driver-less vehicles undoubtedly brings new vitality to a large amount of industries, particularly in transportation. For the mining industry, transportation is undoubtedly an extremely important link in the whole production process. If the driver-less vehicles can be applied to the underground mines, it can not only improve the production and transportation capacity of the whole mine, but also can reduce the occurrence of many mine safety accidents. ZigBee WSN technology can play a greater role in the narrow environment like underground mines according to the relevant literature, this concept paper just like a engineering project plan mainly tries to integrate the ZigBee WSN technology and the communication-based train control (CBTC) system to explore the possibility of the driver-less vehicles to be used in the underground mines, which aims to solve practical engineering problems for the engineering projects. As the mining engineers, we put forward the concept of this integrated system in this concept paper, but we need to continue to work hard for the future of the underground mines. This concept paper serves just as a guide to the Tossing out a brick to get a jade gem, has a few implications for the development of underground mine transportation.

Lung cancer is almost the most common cause of cancer death in the world. Clinically, the conventional therapy to eradicate the cancer cells is chemotherapy but a better drug remains required. In this study, the effects of three bufadienolides, kalantuboside B, kalantuboside A and bryotoxin C, isolated from Kalanchoe tubiflora (Harvey) were evaluated and characterized in CL1-5 highly metastatic human lung cancer cells. Contrary to the apoptosis-promoting activity in other cancer cells, these three bufadienolides did not induce apoptosis in CL1-5 cancer cells. Instead, they activated an autophagy pathway, as indicated by the increase of autophagosomes formation. The induction of autophagy by these three bufadienolides was demonstrated to link to down-regulation of p-mTOR as well as up-regulation of LC3-II, ATG5, ATG7, Beclin-1. Moreover, among these three compounds, kalantuboside B in which a monosaccharide is attached at the bufadienolide aglycon, exhibited a better autophagy induction. Our findings revealed an alternative mechanism of drug action by bufadienolides in lung cancer cells and provided evidence for the possibility of treating highly metastatic human lung cancer through an autophagy pathway.

Visual question answering (VQA) is receiving increasing attention from researchers in both the computer vision and natural language processing fields. There are two key components in the VQA task: feature extraction and multi-modal fusion. For feature extraction, we introduce a novel co-attention scheme by combining Sentence-guide Word Attention (SWA) and Question-guide Image Attention (QIA) in a unified framework. To be specific, the textual attention SWA relies on the semantics of the whole question sentence to calculate contributions of different question words for text representation. For the multi-modal fusion, we propose a “Cross-modal Multistep Fusion (CMF)” network to generate multistep features and achieve multiple interactions for two modalities, rather than focusing on modeling complex interactions between two modals like most current feature fusion methods. To avoid the linear increase of the computational cost, we share the parameters for each step in the CMF. Extensive experiments demonstrate that the proposed method can achieve competitive or better performance than the state-of-the-art.

A new approach for the preparation of polymer brush was developed via the union of controlled/“living” radical polymerization and click chemistry. The application of the approach realized the more quickly and accurate design and synthesis of the polymer brushes. A novel functional polymer brush of poly(acrylonitrile-g-glycidyl methacrylate) with tremendous application potential in the field of biology has been successfully synthesized via the new approach. The reaction conditions of click chemistry were optimized with the reaction time and the reactant ratio and judged from UV-vis spectra. Under the optimum of click chemistry, the novel functional polymer brushes were prepared. The GPC, FTIR analyses, 1H NMR spectrum and TGA were employed to ensure the successful synthesis of poly(acrylonitrile-g-glycidyl methacrylate) polymer brushes.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

This paper presents the experimental implementations of the mathematical models and algorithms developed in Part I. Two experiments are carried out. The first experiment aims at the determinations of the correction coefficients of the mathematical model. The dot grid target is measured and the measurement data are processed by our developed and validated algorithms introduced in Part I. The values of the coefficients are indicated and analysed. Uncertainties are evaluated with implementation of the Monte Carlo method. The second experiment measures a different area of the dot grid target. The measurement results are corrected according to the coefficients determined in the first experiment. The mean residual between the measured points and their corresponding certified values reduced 29.6% after the correction. The sum of squared errors reduced 47.7%. The methods and the algorithms for raw data processing, such as data partition, fittings of dots’ centres, K-means clustering, etc., are the same for both two experiments. The experimental results demonstrate that our method for the correction of the errors produced by the movement of lateral stage of confocal microscope is meaningful and practicable.

Eco-innovation denotes developing green practices using environmentally friendly innovative approaches or technologies. Although, eco-innovation has been broadly applied in different in-dustries, such as low-carbon production and manufacturing, how to implement such innovation in education for sustainable development (ESD) has rarely been studied. Therefore, this research considered a reflective and cooperative learning approach to science, technology, engineering, arts, and math (STEAM) education. A case study examined Wanluan Township of Pingtung County in southern Taiwan. Four departments’ students and teachers at Meiho University were involved in situated learning. Students of hospitality management played farm owners who en-gaged in organic agriculture to produce food and beverages. These agricultural products were farm-to-table, cooked and served for customers in a natural dining setting through the students’ teamwork. Students of tourism, sports & leisure management, and food science & nutrition played tourists in a self-guided travel context, who engaged in acts such as visiting buildings to understand heritage while observing that the houses were still in use a dwelling. This encouraged reflection on the importance of cultural preservation. According to the results from the role-play farm owners and tourists, eco-innovation can represent a sustainable marketing strategy for im-proving the local-community economy and can be implemented in a practical situation in STEAM. The goal of ESD for 2030 — societal transformation — is to foster students’ responsible behavior and attitudes in a personally authentic manner, thereby fostering sustainability learning and understanding.

Autophagy is an evolutionarily conserved mechanism for degrading and recycling different cellular components in both normal development and stress conditions. Our recent research demonstrated that autophagy-mediated compartmental cytoplasmic deletion is essential for pollen germination. However, how autophagy regulates pollen germination to ensure its fertility remains largely unknown. Here, we applied multi-omic analyses to investigate the downstream pathways of autophagy in the process of pollen germination. Although ATG2 and ATG5 play similar roles in regulating pollen germination, high-throughput transcriptomic analysis reveals that silencing ATG5 has greater impact on the transcriptome than silencing ATG2. Cross-comparisons of transcriptome and proteome analysis reveal that gene expression at mRNA level and protein level are differentially affected by autophagy. Furthermore, high-throughput metabolomics analysis demonstrates that pathways related amino acid metabolism and aminoacyl-tRNA biosynthesis can be affected by both ATG2 and ATG5 silencing. Collectively, our multi-omic analyses reveal a central role of autophagy in cellular metabolism, which is critical for the initiation of pollen germination and the guarantee of pollen fertility.

The phycobilisome (PBS) is the major light-harvesting apparatus in cyanobacteria and red algae, a large multi-subunit protein complex of several megadaltons that is found on the stromal side of thylakoid membranes in orderly arrays. Chromophore lyases catalyse the thioether bond between apoproteins and phycobilins of PBSs. Depending on the species, composition, spatial assembly and, especially, the functional tuning of different phycobiliproteins mediated by linker proteins, PBSs can absorb light between 450 and 650 nm, making them efficient and versatile light-harvesting systems. However, basic research and technological innovations are needed, not only to understand their role in photosynthesis but also to realise the potential applications of PBSs. Synthetic biology provides an innovative approach to expand our understanding of the distinctive properties that make the PBS such an efficient light-harvesting system and to explore its heterologous synthesis, photosynthetic functions and potential medical applications. Focusing on these topics, this review describes the essential components needed for PBS assembly, the functional basis of PBS photosynthesis and the applications of phycobiliproteins. Moreover, key technical challenges for heterologous biosynthesis of phycobiliproteins in chassis cells are discussed.

The existences of the N→C dative bonds in the complexes between N-containing molecules and fullerenes have been verified both theoretically and experimentally. However, finding stable N→C dative bonds is still a highly challenging task. In this work, we investigated computationally the N→C dative bonds in the complexes formed by fullerene C60 with 1,2,5-chalcogenadiazoles, 2,1,3-benzochalcogenadiazoles and 1,2,4,5-chalcogenatriazoles, respectively. It was found that the N→C dative bonds are formed along with the formation of the N–Ch···C (Ch = S, Se, Te) chalcogen bonds. In the gas phase, from S-containing complexes through Se-containing complexes to Te-containing complexes, the intrinsic interaction energies become more and more negative, which indicates that the N–Ch···C chalcogen bonds can facilitate the formation of the N→C dative bonds. The intrinsic interaction energies are compensated by the large deformation energy of fullerene C60. The total interaction energies of Te-containing complexes are negative, while both of the total interaction energies of S-containing complexes and Se-containing complexes are positive. This means that the N→C dative bonds in the Te-containing complexes are more easily observed in experiments in comparison with those in the S-containing complexes and Se-containing complexes. This study provides a new theoretical perspective on the experimental observation of the N→C dative bonds in the complexes involving fullerenes. Further, the formation of stable N→C dative bonds in the complexes involving fullerenes can significantly change the properties of fullerenes, which will greatly simulate and expand the application range of fullerenes.

Objectives To determine the effects of omega-3 polyunsaturated fatty acids (ω-3 PUFA) from animal and plant sources on glucolipid metabolism and lipoprotein subfractions in type 2 diabetic patients with dyslipidemia. Methods Participants were recruited from the diabetes clinic at the Guanlin Hospital, Yixing City in Jiangsu province, China, from March 2017 through June 2017. Ninety participants were randomly assigned to take 3g/day fish oil (FO, containing EPA and DHA), 3g/day perilla oil (PO, containing ALA), or 3g/day blend oil containing fish oil and linseed oil (BO, containing EPA, DHA and ALA) for 3 months. The levels of serum glucose, glycated hemoglobin (HbA1c), C-peptide, triglyceride (TG), total cholesterol (TC), high-density lipoprotein (HDL), low-density lipoprotein (LDL), non-HDL, apolipoprotein A1 (Apo A1), apolipoprotein B (Apo B), lipoprotein a (Lp(a)), and free fatty acids were determined at baseline and after the 3 months. In addition, four fatty acids in serum and red blood cells membranes (RBCm) were analyzed using gas chromatography-mass spectrometry. The Lipoprint System was used to determine the lipoprotein subfractions. Results All 90 participants completed the final 3-month follow-up at the end of the study. After three months of intervention, blood glucose and HbA1c levels in the PO group were significantly lower than those at the baseline (p < 0.05). On the other hand, in the BO group, the HbA1c, non-HDL, Apo A1 and Lp(a) levels were significantly lower, while the C-peptide levels were significantly higher after intervention compared to the baseline (p < 0.05). In the FO group, the HbA1c and TG levels were significantly lower after the intervention compared to the baseline (p < 0.05). In addition, at the end of the study, there was significant increase in the levels of DPA and DHA in serum and RBCm of the FO group (p < 0.05), while in the BO group, there was significant increase in the levels of EPA, DPA and DHA in RBCm (p < 0.05). Finally, the FO group had the highest levels of large HDL subfractions compared to the BO and PO groups, but had the lowest levels of small HDL subfractions among the three groups. Conclusion For patients with diabetes, plant-derived ω-3 PUFAs are more effective at controlling blood glucose than animal-derived ω-3 PUFAs. However, animal-derived ω-3 PUFAs play a critical role in controlling blood lipids. Particularly, fish oil can effectively increase the beneficial large HDL subfractions and reduce the nonbeneficial small HDL subfractions. Both the animal- and plant-derived ω - 3 PUFAs have practical value in improving glucose and lipids metabolism in T2DM patients with dyslipidemia.

Fructus Amomi (FA) is usually regarded as the dried ripe fruits of Amomum villosum Lour. (FAL) or Amomum villosum Lour. var. xanthioides T. L.Wu et Senjenis (FALX) However, FAL, which always has a much higher price because of its better quality, is confused with FALX in the market. As volatile oil is the main constituent of FA, a strategy of chromatography-mass spectrometry (GC-MS) and chemometric approches was applied to compare the chemical composition of FAL and FALX. The results showed that the oil yield of FAL was significantly higher than that of FALX. Total ion chromatograph (TIC) showed that cis-nerolidol existed only in FALX. Bornyl acetate and camphor, could be considered as the most important ones in FAL and FALX respectively. Moreover, hierarchical cluster analysis (HCA) and principal component analysis (PCA) successfully distinguished the chemical constitutes of the volatile oils in FAL and FALX. Additionally, bornyl acetate, α-cadinol, linalool, β-myrcene, camphor, d-limonene, terpinolene and endo-borneol were selected as the potential markers for discriminating FAL and FALX by partial least squares discrimination analysis (PLS-DA). In conclusion, this present study first developed a scientific approach to separate FAL and FALX based on volatile oils by GC-MS combined with chemometric techniques.

Both ricin and R. communis agglutinin (RCA120), belonging to the type II ribosome-inactivating proteins (RIPs-Ⅱ), are derived from the seeds of castor bean plant. They share very similar amino acid sequences, but ricin is much more toxic than RCA120. It is urgently necessary to distinguish ricin and RCA120 in response to public safety. Currently, mass spectrometric assays are well established for unambiguous identification of ricin by accurate analysis of differentiated amino acid residues after trypsin digestion. However, diagnostic peptides are relatively limited for unambiguous identification of trace ricin, especially in complex matrices. Here, we demonstrate a digestion strategy of multiple proteinases to produce novel peptide markers for unambiguous identification of ricin. LC-HRMS was used to verified the resulting peptides, among which only the peptides with uniqueness and good MS response were selected as peptide markers. Seven novel peptide markers were obtained from tandem digestion of trypsin and endoproteinase Glu-C in PBS buffer. From the chymotrypsin digestion under reduction and non-reduction conditions, eight and seven novel peptides were selected respectively. Using pepsin under pH 1~2 and proteinase K digestion, 6 and 5 peptides were selected as novel peptide markers. In conclusion, the obtained novel peptides from the established digestion methods can be recommended for the unambiguous identification of ricin during the investigation of illegal use of the toxin.

As China put forward its “carbon emissions peak and carbon neutrality” goals, how to achieve carbon reduction had become a key for China’s goal. The manufacturing industry is an important source of carbon dioxide emissions. For a manufacturing country like China, adjustments in various aspects of the industry would have a huge impact on carbon emissions. As an important reform of contemporary production mode, the process of production automation in China will inevitably affect China's carbon emissions. Therefore, the analysis of the impact of production automation on carbon dioxide emissions was an important basis for judging the future carbon reduction in China. Refer to the traditional study of carbon Kuznets curve, this paper analyzed the impact of average wage on production automation and the role of production automation in the carbon Kuznets curve(CKC). This paper proposed that production automation plays a mediating role in the process of carbon emissions, and gives a verification model of the mediating role. By analyzing the relationship between average wage and production automation process, the U-shaped curve relationship between them was verified. By examining the relationship between carbon dioxide emission data and production automation industry in China, we verified that production automation plays a partial mediating role in the change of carbon Kuznets curve. Combined with the analysis of the two parts, this paper believed that with the continuous development of China's intelligent manufacturing industry, China's carbon reduction prospects were more optimistic, and there was a good industrial foundation to achieve the “carbon peaking and carbon neutrality” goals. Finally, this paper proposes policy suggestions as increase research investment in production automation, help promote the application of production automation, encourage the research and application development of low-carbon technology, especially encourage modular design, so as to give full play to the role of production automation in the process of carbon neutrality in China.

Skeletal muscle atrophy is one of the major side effects of high dose or sustained usage of glucocorticoids. Pyroptosis is a novel form of pro-inflammatory programmed cell death that may contribute to skeletal muscle injury. Trimetazidine, a well-known anti-anginal agent, can also improve skeletal muscle performance both in human and mice. We here showed that dexamethasone induced atrophy, evidenced by the increase of muscle atrophy F-box (Atrogin-1) and muscle ring finger 1 (MuRF1) expression , and the decrease of myotube diameter in C2C12 myotubes. Dexamethasone also induced pyroptosis, indicated by upregulated pyroptosis-related protein NLRP3, Caspase-1 and GSDMD. Knockdown of NLRP3 or GSDMD attenuated dexamethasone-induced myotube pyroptosis and atrophy. Trimetazidine administration ameliorated dexamethasone-induced muscle atrophy both in vivo and in vitro. Moreover, trimetazidine improved exercise tolerance, as evidenced by increased running distance and running time, as well as increased skeletal muscle mass in dexamethasone-treated mice. Mechanically, trimetazidine could reverse dexamethasone-induced activation of pyroptosis both in C2C12 myotubes and in mice. Taken together, our present study demonstrated that NLRP3/GSDMD pathway-mediated pyroptosis was involved in dexamethasone-induced skeletal muscle atrophy. Trimetazidine could partially alleviate dexamethasone-induced skeletal muscle atrophy, and increase the diameter of C2C12 myotubes via inhibiting pyroptosis. Thus, trimetazidine might be a potential therapeutic compound for the prevention of muscle atrophy in glucocorticoid-treated patients.

Understanding how industrial agglomeration affects agricultural green production efficiency is essential for green agricultural development. This study uses the super-efficient EBM-GML to measure and analyze the spatial and temporal evolution characteristics and core sources of dynamics of agricultural green production efficiency in China by using panel data from 30 Chinese provinces from 2006 to 2020. It also empirically investigates the relationships between industrial agglomeration, land transfer, and agricultural production efficiency. By using fixed, intermediary, and threshold effects models, the internal links between the industrial agglomeration, land transfer, and agricultural green production efficiency are examined. The findings indicate that the green production efficiency of Chinese agriculture exhibits the regional characteristics of being “high in the west and low in the east, high in the south and low in the north” in terms of space; in terms of time series, the overall trend is that of growing, with an average annual growth rate of 11.45%, and the growth primarily depends on the “single-track drive” of green technological progress. By promoting land transfer, industrial agglomeration can increase the agricultural green production efficiency and decomposition index. Land transfer has a double-threshold effect on the influence of industrial agglomeration on agricultural green production efficiency. As a result, this study suggests adhering to the idea of synergistic development, promoting agricultural green development, strengthening the development of industrial agglomerations, promoting the quality and efficiency of industry, improving land-transfer mechanisms, and placing a focus on resource efficiency improvements, as well as other policy recommendations.

Endoscopic retrograde cholangiopancreatography (ERCP) is a routinely used therapeutic procedure for the biliary and pancreatic diseases. Population aging may increase the typical indications of ERCP and come with more complexity and difficulties, especially in cannulation. This study aimed to evaluate the incidence, causes, and management of difficult biliary cannulation during ERCP in super-aged patients and the role of difficult cannulation as a risk factor for adverse events. A total of 614 patients, underwent ERCP, were prospectively studied as a cohort and divided into two groups based on their age. There were 146 patients aged 80 years or older in group A and 468 patients aged less than 80 years in group B. The primary outcome measures were the difficulty grade of papilla cannulation, clinical outcomes, and ERCP-related complications in the two groups. The adverse events were analyzed using logistic regression for patient age, co-morbidities, indications, and cannulation difficulty grade variables. There was no difference in the incidence of difficult cannulation between the two groups (32.9% vs. 34.4%, p=0.765) though, as expected, super-aged Group A had a higher prevalence of periampullary diverticulum (29.5% vs. 16.7%, p=0.001). The technical cannulation success rate was (96.6% vs. 96.8%, p= 0.54). All used cannulation techniques in the elderly group were efficient and safe. Logistic regression showed that age ≥80 was not associated with increased adverse events; however, difficult cannulation (adjusted odds ratio [AOR]=3.478; 95% confidence interval [CI]=1.877, 6.442; p<0.001) and CCI ≥2 (AOR=1.824; 95% CI=0.993, 3.349; p=0.045) were more likely to have adverse events. Age ≤65 (AOR=3.460; 95% CI=1.511, 7.922; p=0.003), female gender (AOR=2.362; 95% CI=1.089, 5.124; p=0.030), difficult cannulation (AOR=4.527; 95% CI=2.078, 9.860; p<0.001), and patients with cholangitis (AOR=3.261; 95% CI=1.204, 8.832; p=0.020) were strongly associated with increasing Post-ERCP Pancreatitis (PEP). Advanced age has not proved to be a risk factor of difficult cannulation, and secondary cannulation techniques can be safely and efficaciously utilized for this group. CCI ≥2 and difficult cannulation are associated with increased overall adverse events rate while age ≥80 factor is not.

Promoting close and sustainable cooperation between schools, enterprises, and government has become an important concern in many countries. Based on evolutionary game theory, this paper constructs a tripartite evolutionary game model of schools, enterprises, and government in order to analyze the stability of strategies of the different players. The results show that the main factor that influences the stability of the strategies of schools and enterprises is the reward of positive cooperation from sources other than the government, and the main factor that influences the stability of the strategy of the government is the benefit of positive cooperation strategy under the scenario where schools cooperate with enterprises. Therefore, the government should focus on implementing more effective policies, such as increasing the incentives and penalties, improving the mechanism for managing conflicts, ensuring the fairness of benefits distribution, and clarifying the responsibilities of different departments; schools should focus on providing more practical curricula and programs for students, training high-quality teachers, and perfecting talent cultivation to meet the needs of enterprises; and enterprises should focus on providing job experiences for students and transforming the results of schools’ teaching and theoretical research into practical productivity.

Fasudil, a potent Rho kinase (ROCK) inhibitor, can ameliorate LPS-induced acute lung injury (ALI) in mice, but the mechanism remains obscure. In this study, a mice model of ALI was established by intra-tracheal instillation of LPS. Histological changes, cytokine levels, lung permeability, and endothelial apoptosis were determined to evaluate the effects of fasudil on lung injury. The cellular and molecular biological mechanisms were explored by culturing human pulmonary microvascular endothelial cells (PMECs). The results showed that fasudil reduced LPS-induced lung inflammation, pulmonary hyperpermeability, and endothelial apoptosis in mice. In cultured human PMECs, fasudil inhibited LPS-induced caspse-3 cleavage and cell apoptosis. It also decreased LPS-induced hyperpermeability of human PMECs monolayer by reversing the down-regulation of intercellular junctions. Moreover, fasudil inhibited LPS-induced overexpression of chemokines and intercellular adhesion molecule (ICAM)-1 in human PMECs, which in turn suppressed neutrophil chemotaxis and neutrophil-endothelial adhesion. Further molecular researches showed fasudil inhibited LPS-induced activation of ROCK, NF-κB, and p38 in human PMECs. Our findings demonstrated that fasudil alleviated LPS-induced ALI by protecting endothelial function via inhibiting endothelial apoptosis, maintaining endothelial barrier integrity, and reducing endothelial inflammation. These effects of fasudil could be attributed to the inhibition of ROCK and its downstream NF-κB and p38 signaling pathways.

Influenced by the quasi-stationary Mei-yu front and the development of mesoscale low vortices on the Mei-yu front, a torrential rain event occurred in Suzhou on July 6, 2020. The 24-hour rainfall recorded by the automatic station exceeded 200 millimeters, with the highest hourly intensity surpassing 70 millimeters, accompanied by thunderstorms and strong winds. This heavy precipitation process was characterized by suddenness, extremity, long duration, high precipitation efficiency, and backward propagation. Using various data sources such as the European ERA5 reanalysis data, ground-based automatic stations, sounding, Doppler weather radar, and wind profile radar, this paper analyzed in detail the circulation characteristics and radar echo structures of this torrential rain event, and further studied the triggering, feature evolution, and maintenance mechanisms of the heavy precipitation.The results show: (1) The continuously strengthening low-level jet stream propagates downward forming an ultra-low-level jet stream. Heavy precipitation is located on the left front side of the jet exit area, where strong convergence and lifting in the boundary layer overlap with the ascending branch of the secondary circulation above the shear line, resulting in heavy precipitation. (2) A supercell storm with intense precipitation produced this heavy rainfall event, characterized by a low centroid of strong echo; echo-free vault, bounded weak echo region, and other supercell structural features. During this event, the high reflectivity factor areas corresponded to high KDP value areas, indicating a large amount of liquid water content. Vertically, the KDP column can track the rainwater mixing ratio well, and its location corresponds to the vicinity of the short-term heavy precipitation occurrence. The high KDP value area mainly consists of numerous precipitation particles, and the vertical vortex wind field structure causes rapid growth of precipitation particles through continuous rolling. Furthermore, it can be found through correlation coefficients (CC) that there are always high-value areas for CC since they correspond to areas of intense precipitation. (3) Continuous triggering of mesoscale convective cloud clusters on the east-west ground convergence line leads to new development and forms a "train effect." Strong frontogenesis in both horizontal and vertical directions triggers and sustains this heavy precipitation event. The significant increase in liquid water and water vapor density has indicative significance for the occurrence of heavy precipitation.

The intestinal microbiota, comprised of bacteria, archaea, and phages, inhabits the gastrointestinal tract of the organism. Male reproductive sterility is currently a prominent topic in medical research. Increasing research suggests that gut microbiota dysbiosis can result in various reproductive health problems. This article specifically investigates the impact of gut microbiota dysbiosis on male reproductive infertility development. Gut microbiota imbalances can disrupt the immune system and immune cell metabolism, affecting testicular growth and sperm production. This dysfunction can compromise the levels of hormones produced and secreted by the endocrine glands, affecting male reproductive health. Furthermore, imbalance of the gut microbiota can disrupt the gut-brain-reproductive axis, resulting in male reproductive infertility. This article will explore how the imbalance of the gut microbiota impacts male reproductive infertility through immune regulation, endocrine regulation, and interactions of the gut-brain-reproductive axis, concluding with recommendations for prevention and treatment.

Periostracum cicadae, the cast-off shell of the cicada Cryptotympana pustulata Fabricius, is used in traditional Chinese medicine for its diaphoretic, anticonvulsive, sedative, antipyretic, and antiallergic effects. However, the exact pathogenesis of immunoglobulin A nephropathy (IgAN) remains unclear, thereby hindering investigations to identify novel therapeutic agents. A rat IgAN model was established by administration of bovine serum albumin, lipopolysaccharide, and carbon tetrachloride, which simultaneously established blood stasis and a heat syndrome model. The animals were sacrificed to detect changes in protein levels in urine and blood. Immunofluorescence was performed to assess IgA deposition in the glomeruli. Tumor necrosis factor-α (TNF-α), interleukin-1β (IL-1β), and interleukin 6 (IL-6) levels were measured in bronchoalveolar lavage fluid (BALF) by enzyme-linked immunosorbent assay. Hematology and eosin, periodic acid-Schiff, TUNEL, and immunohistochemical staining were performed to evaluate histopathological changes in kidney tissues. Additionally, target-related proteins were measured by western blotting. Periostracum cicadae resulted in a reduction in blood and urine protein levels. Serum TNF-α, IL-1β, and IL-6 levels significantly decreased in the periostracum cicadae-treated groups compared to the IgAN group. Furthermore, a reduction in MCP-1, TLR4, and IgA expression levels and a dose- dependent increase in caspace-3 expression were observed in response to periostracum cicadae treatment. TGF-β1 levels decreased, whereas that of Fas increased in the kidney tissues of the periostracum cicadae-treated groups. The findings of the present study indicate that periostracum cicadae induces apoptosis and improves kidney inflammation and fibrosis in IgA nephropathy rat models.

New antimicrobial approaches are essential to counter antimicrobial resistance. The drug development pipeline is exhausted with emergence of resistance resulting in unsuccessful trials. The lack of an effective drug developed from the conventional drug portfolio has mandated the introspection into the list of potentially effective unconventional alternate antimicrobial molecules. Alternate therapies, that are clinically explicable forms include monoclonal antibodies, antimicrobial peptides, aptamers and phages. Clinical diagnostics optimizes the drug delivery. In the era of diagnostic-based applications, it is logical to draw diagnostic based treatment for infectious diseases. Selection criteria of alternate therapeutics in infectious disease include detection, monitoring of response and resistance mechanism identification. Integrating these diagnostic applications is disruptive to the traditional therapeutic development. The challenges and mitigation methods need to be noted. Applying the goals of clinical pharmacokinetics that include enhancing efficacy and decreasing toxicity of drug therapy this review analyses the strong correlation of alternate antimicrobial therapeutics in infectious diseases. The relationship between drug concentration and the resulting effect defined by the pharmacodynamic parameters are also analyzed. This review analyzes the perspectives of aligning diagnostic initiatives into the use of alternate therapeutics with a particular focus on companion diagnostic applications in infectious diseases.

Background: During pregnancy, major physiological changes occur in every system. Understanding the hemodynamic changes in different stages of pregnancy can help to identify abnormal states during pregnancy. Harmonic analysis could be a useful tool in monitoring the state of the ventricular-arterial system during pregnancy. The aim of this study was to investigate the specific statistical relationships between changes in harmonic indices during different stages of pregnancy. Methods: A Total of 380 women (190 pregnant women and 190 age-matched non-pregnant women), with ages ranging from 20 to 45, were enrolled in the study. The visit measured the subject’s hemodynamic parameters including heart rate, systolic blood pressure (SBP), diastolic blood pressure (DBP) and photoplethysmography (PPG). SBP and DBP were evaluated by an automatic blood pressure monitor. PPG signal were continuously recorded for 12-seconds using a PPG sensor. Spectrum analysis of the PPG signal was performed to evaluate the first five harmonic components (C1 – C5) and harmonic phases (P1 – P5). Result: A comparison between pregnant women and non-pregnant women showed that the non-pregnant women had lower DBP, C3, C5 and P5 (p<0.05). Waist Circumference, Heart rate, C2, C4 and P2 were higher in pregnant women. Logistic regression analysis was used to determine the associations between pregnancy and harmonics indices. C2, C4 and P3 were positively and P1 and P4 were negatively associated with pregnancy after controlling age, BMI, waist circumference, heart rate, SBP and DBP. Conclusion: The results of this study provide information on the changes in the harmonic frequency components during various stages of pregnancy. The harmonic components of the PPG signal have independent predictive value for changes in a woman's physiology during pregnancy. Since non-invasive PPG measurements can be performed frequently and easily, in the future, it is possible that the hemodynamic changes from some pregnancy-related disorders could be studied by harmonic analysis.

Multi-gap Resistive Plate Chamber has been attracting increasing attention and has been studied in recent decades because of its good efficiency, high time resolution and relatively low cost. It has become a new standard technology for the Time of Flight system in particle and high energy physics experiments. In this paper, we introduce the operation principle and structure of the MRPC detector and review the applications on the Time of Flight system in several famous experiments, such as STAR, CBM and SoLID. The performances including time resolution and particle identification are discussed in detail. Some recent advances and perspectives with regard to the future development of the next generation MRPC are also outlined.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

Ammonia-oxidizing microorganism communities are abundant and functionally efficacious in nitrification. However, ammonia-oxidizing archaea (AOA) and ammonia-oxidizing bacteria (AOB) groups complicate this process in subtropical streams. This study investigates the abundance of ammonia-oxidizing communities south of the Dabie Mountains, China, using quantitative polymerase chain reaction (qPCR). Clone libraries were utilized to analyze the abundance and microbial structures of AOA and AOB in sediments. Such analysis may provide strong evidence reflecting the links within the environment. The results show that AOB had a lower abundance of copies of the ammonia-oxidizing gene (amoA) than AOA. Interestingly, the AOA and AOB community compositions were correlated with ecological characteristics. The dissolved oxygen (DO) and oxidation-reduction potential (ORP) had significant positive correlations, whereas the phosphorus within the structure had a negative correlation with the abundance of both groups. Our study shows that it might adopt some species related to Nitrosotalea clusters that can resist comparably higher pH (toward pH 6.5). Together, these results imply that the physiological adaptation of microbial guilds to environmental pressures in ammonia-oxidizing archaea might allow them to have a more substantial function of ammonia-oxidizing communities in natural habitats.

Hyperspectral images (HSI) contain abundant spectral information. Efficient extraction and utilization of this information for image classification remain prominent research topics. Previously, hyperspectral classification techniques primarily relied on statistical attributes and mathematical models of spectral data. Deep learning classification techniques have recently been extensively utilized for hyperspectral data classification, yielding promising outcomes. This study proposes a deep learning approach that uses polarization feature maps for classification. Initially, the polar coordinate transformation method is employed to convert the spectral information of all pixels in the image into spectral feature maps. Subsequently, the proposed Deep Context Feature Fusion Network (DCFF-NET) is utilized to classify these feature maps. The model is validated using three open-source hyperspectral datasets: Indian Pines, Pavia University, and Salinas. The experimental results indicated that DCFF-NET achieves excellent classification performance. Experimental results on three public HSI datasets demonstrate that the proposed method accurately recognizes different objects with an overall accuracy (OA) of 86.68%, 94.73%, and 95.14% based on the pixel method, and 98.15%, 99.86%, and 99.98% based on the pixel-patch method.

To prepare an edible coating with a good preservative effect on sweet cherries, carboxymethyl chitosan (CMCS) and gelatin (GL) were selected as the film-forming matrix in this experiment, and CaCl2 and ascorbic acid (AA) were added as crosslinking agents and antioxidants, respectively. First, the film was prepared by the casting method, and the film formula with better mechanical and barrier performance was filtered out by one-factor and response surface optimization test, and the differences in the preservation effect of different film formulations (CMCS-GL, CaCl2- CMCS-GL, AA -CaCl2- CMCS-GL) on sweet cherries were compared. and then the different film formulations were compared. The difference in film formulation on the preservation effect of sweet cherries was investigated. The results showed that the optimal formulation for an edible film based on CMCS-GL with good performance was CMCS: GL (w:w)=2:1, with the additional amount of 1% glycerol, 2% CaCl2, 0.1% Tween-20, 2% AA, the tensile strength, elongation at break, oxygen permeability and water vapor permeability of the film obtained with this formula were: 16.28 MPa, 71.46%, 1.39×10-12 g- cm/(cm2-s-Pa), 5.10×10-11 cm3-cm/(m2-s-Pa), respectively. In the preservation of sweet cherries, all three film formulations effectively reduced the rotting rate and weight loss during storage while preserving the high hardness and skin color of the fruit. Among them, the formulation AA -CaCl2- CMCS-GL showed the best preservation effect and can be used as a new method for postharvest preservation of sweet cherries.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.