In this work, the structural, magnetic, and mechanical properties of Nd16Fe76-xCoxB8 alloys varying the Co content at x = 0, 10, 20 and 25, were experimentally investigated by X-Ray Diffraction (XRD), Mössbauer Spectrometry (MS), Vibrating Sample Magnetometry (VSM) at room temperature (RT), and microhardness test were performed too. The system presents the hard Nd2Fe14B and the Nd1.1Fe4B4 phases for samples with x = 0 and 10. When concentration increases to x= 20 and 25, the CoO phase appears. All MS show the ferromagnetic behavior (eight sextets: sites 16k1, 16k2, 8j1, 8j2, 4c, 4e, sb) associated to the hard and soft magnetic phases, and one paramagnetic component (doublet: site d) associated to the minority Nd1.1Fe4B4 phase, which was not identified by XRD. All samples are magnetically hard present a hard magnetic behavior. The increase of Co content in these samples did not improve the hard magnetic behavior, but increased the critical temperature of the system and decrease the crystallite size of the hard phase. The hysteresis loop showed that predominates the Nd2Fe14B hard magnetic phase. There is a general tendency to increase microhardness with cobalt content, attributable to cobalt doping reduces the lattice parameters and porosities in the sample improving it hardness.

In a 1.5°C warmer world, the Northeastern (NE) South America’s ecosystems will experience more severe droughts, associated with decreasing rainfall. The severity of flash drought events based on vegetation and surface soil moisture has not been identified over the Caatinga ecosys-tem. This study aimed to characterize the impact of flash drought events on vegetation response via soil moisture over NE South America during the first two decades of the 2000s. Three drought indices were used to characterize flash droughts: the Standardized Difference Vegetation Index (SDVI) derived from Meteosat Second Generation (MSG), the Standardized Precipitation Index (SPI) from ground-data, and the Surface Soil Moisture (SSM) product-based Soil Moisture and Ocean Salinity (SMOS). Results revealed dramatic impacts of flash drought events on vegetation dynamics that caused abrupt changes in the regional vegetation phenology. The regional patterns of flash drought events in 2012 over NE South America were identified and had a severe impact on its Caatinga-like vegetation-dependent moisture response. In 2012, anomalously long dry spells with negative rainfall anomalies in the non-rainy season and persistent on vege-tation greenness and rapidly decreased soil moisture were prominent, thus identifying NE South America to the impacts of flash drought events. Additionally, the results from the trends analysis of radiance fluxes estimated from the MSG satellites over 18 years revealed that an overall drying trend in the NE South America semiarid ecosystem during the last two decades. Here, flash drought events were identified as the conse-quent rainfall deficiency at SPI-3< −1 for a period of five consecutive weeks or more, which the soil moisture content dropping from the 40th percentile to below the 20th percentile, with the NDVI lower than 0.30 unit. These results could be useful to guide flash-droughts early warning systems in NE South America.

The microstructure of the coating during hot-dip galvanizing under industrial conditions of two structural steels, a low-silicon ASTM A36 steel and a high-silicon Q345B steel, both of commercial quality, have been characterized for industrial-relevant times. For both cases it is noted that the formation of the Fe-Zn phases begins in early stages during the heating of the steel, a situation in which all the phases are in the solid state. The characterization was carried out through traditional metallographic techniques including SEM-EDS and DRX equipment. The evolution in time of the microstructure of both steels is examined, being able to observe that the mechanism by which silicon accelerates the formation of Fe-Zn phases in galvanizing is related to the change in the energy of the interfaces caused by a silicon accumulation in the liquid phase in contact with the ζ layer. These results provided us with a deeper understanding of the phase evolution in the hot-dip galvanizing of high silicon steels.

Topology optimization has become a very popular design tool when an optimum design with a concrete objective and subjected to several restrictions is searched. However, the resultant shape of the optimization process isn’t usually easy to manufacture with a typical manufacturing method as machining, being necessary an interpretation and validation of the result; besides, some parameters can be chosen, and the final shape is directly dependent on them. In this paper, a sensitivity analysis of the main parameters involved in 3D topology optimization, the penalization and the filter radius, is carried out for the concrete case of the density-based method, analyzing how manufacturable the results are for 3 axis machining. Also, a new filter and method is proposed for obtaining highly manufacturable and low interpretable parts. The main aim of the study is to help designers to choose the more appropriate parameters and showing what they must have into account for obtaining the desired optimized shapes. Note that the density-based topology optimization method has been chosen due to its popularity in commercial packages, so the conclusions may have direct applications in designers’ work. Finally, the results of the study are verified through different cases for checking the validity of the conclusions.

Mild Cognitive Impairment (MCI) may progress to severe forms of dementia, so therapy is needed to maintain cognitive abilities. The neural circuitry for oculomotor control is closely linked to that which controls cognitive behavior. In this study, we tested whether training the oculomotor system with gaze-controlled video games could improve cognitive behavior in MCI patients. Patients played a simple game for a month while a control group played the same game using a mouse. Cognitive improvement was assessed using the MoCA screening test and CANTAB. We also measured eye pupil and vergence responses in an oddball paradigm. The results showed an increased score on the MoCA test specifically for the visuospatial domain and on the Rapid Visual Information Processing test of the CANTAB battery. Pupil responses also increased to target stimuli. Patients in the control group did not show significant improvements. This pilot study provides evidence for the potential cognitive benefits of gaze-controlled gaming in MCI patients.

Background: Cognitive-behavioral alterations can occur after an acquired brain injury. It is a stressful situa-tion for patient and relatives. Objectives: To develop and evaluate a synchronous online training program on emotional intelligence (EI) for caregivers of adult patients with cognitive-behavioral impairment due to acquired brain injury. Methods: A quasi-experimental study was designed, a target population of ten caregivers attended to a one-month virtual synchronous course about EI. The emotional status of caregivers was registered one-month-previous and one-month-post program using comparative measures: The Trait Meta-Mood Scale (TMMS-24) and the Positive and Negative Affect Schedule (PANAS). Results: Median age of the ten caregivers was 48 years, 80% of women with a median care-time of 6 years. 50% of them were spouses of the patients. 60% of the patients were affected by stroke (hemorrhagic or ischemic cause). The main cognitive impairment of the patients reported by relatives was memory deficit. After re-ceiving training, favorable changes were found regarding emotional affect measured with the PANAS, both positive (increase) and negative (decrease), as well as with the TMMS-24-mood-repair area (p < 0.05). Conclusions: Training in EI helps caregivers to make their mood more positive and improve aspects of their emotional intelligence such as emotional regulation.

Many buildings built before the energy performance regulations are in a situation of thermal discomfort and energy inefficiency. The creation of intelligent environments advances towards new opportunities, based on real-time monitoring and on the development of sensors and technologies. Furthermore, the standards for building automation and electronic systems enable interoperability and interconnection between control devices and systems. The application of soft computing has significantly improved the energy efficiency, however, requires prior assessment to design the automation functions. Temperature, humidity, air quality, occupancy and energy consumption are the most common measured parameters, but the relationship with other operational variables such as occupancy or some building states remains as a research challenge. This article presents a methodology to develop the automatization of an existing large public building. The methodology consists of three stages: 1. Assessment and diagnosis to set appropriate actions using EN ISO 52120-1. 2. EN 50090 for open communication networks, and EN ISO 52120-1 to assign the technical building management. 3. System control deploying of low-cost and low-consumption input and output devices. It has been proved that it is possible to effectively automate an obsolete building with a low cost, open source system that can be easily applied in other buildings.

This article theoretically derives the magnetic field and vector potential produced by a steady current I flowing in an arbitrary plane loop at an arbitrary point r. Numerical examples are presented to demonstrate the behavior of the magnetic field produced by loops of various shapes such as polygons, circles, ellipses, and p-norm balls. Taking the limit as the loop shrinks to a point and the current I grows to infinity so that the magnetic dipole moment m of the loop (defined as the current I times the vector area of the loop) is kept constant, the magnetic field and vector potential are theoretically shown to converge to those of an ideal point magnetic dipole m.

Abstract: Background: Surgery on varicose veins (crossectomy and stripping) leads to recurrence and has clinical and socio-economic repercussions. Their etiopathogenesis has yet to fully under-stood. Objective: Study the expression of endoglin and other molecules involved in the neovascu-larisation process in patients suffering from this disease. Methods: 43 patients that have undergone surgery for varicose veins (24 primary and 19 recurrent). They were identified on the venous wall (proximal -saphenofemoral junction- and distal), via real-time RT-PCR, and in serum, via ELISA: Endoglin (Eng), Vascular Endothelial Growth Factor (VEGF-A), its receptors 1 and 2 (VEGFR1 or FLT1), (VEGFR2 or FLK), and the Hypoxia-Inducible Factor (HIF-1A). All the patients signed a con-sent form. Results: The recurrent group recorded a higher expression of Eng, VEGF-A, VEGFR1 and VEGFR2 at the level of proximal venous wall compared to the primary group. HIF-1A did not record any differences. As regards the determination of the distal venous wall, no markers recorded differ-ences between the groups. Among the serum determinations, only sFLT1 recorded a significant drop among the patients with recurrent varicose veins. Conclusions: Patients with recurrent vari-cose veins record a higher expression of endoglin and other markers of angiogenesis in proximal veins. Endoglin in the blood (sEng) has not proven to be of any use in recurrent varicose veins.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

The study of photonic crystals has emerged as an attractive area of research in nanoscience in the last years. In this work we study the properties of a two-dimensional photonic crystal composed of dielectric rods. The unit cell of the system is composed of six rods organized on the sites of a C6 triangular lattice. We induce a topological phase by introducing an angular perturbation ϕ in the pristine system. The topology of the system is then determined by using the so-called k.p perturbed model. Our results show that the system presents a topological and a trivial phases, depending on the sign of the angular perturbation ϕ. The topological character of the system is probed by evaluating the electromagnetic energy density and analyzing its distribution in the real space, in particular on the maximal Wyckoff points. We also find two edge modes at the interface between the trivial and topological photonic crystals, which present a pseudospin topological behavior. By applying the Bulk-Edge correspondence, we study the pseudospin edge modes and conclude that they are robust against defects, disorder and reflection. Moreover, the localization of the edge modes leads to the confinement of light and the interface behaves as a waveguide for the propagation of electromagnetic waves. Finally, we show that the two edge modes present energy flux propagating in opposite directions, which is the photonic analogue of the quantum spin Hall effect.

In this review, we present the latest exclusion limits obtained with astroparticles for Lorentz Invariance Violation (LIV) in the photon sector. We discuss the techniques known as energy-dependent time delay or time lag, subluminal pair production threshold shift, superluminal photon decays and superluminal photon splitting. Perspectives for future results in LIV with the next generation of experiments are also addressed.

In this paper a dynamic relationship between the CO2 emissions in Finland, Norway and Sweden is presented. With the help of a VAR(2) model, and using the Granger terminology, it is shown that the emissions in Finland are affecting those in Norway and Sweden. Other aspects of this dynamic relationship are presented as well.

3D printing with earth-based mortar is still under development and faces challenges. Optimizing the mortar mixture, improving structural strength, determining the relationship between printing speed and the amount of extruded material, and ensuring long-term durability are areas that are still being refined. Additionally, regulatory and certification issues must also be considered to ensure the safety and compliance of 3D printed structures. This paper presents for discussion the records, analyses, studies, and considerations regarding the initial initiatives involving 3D printing with the extrusion of earth-based mortar developed at the Faculty of Engineering of the University of Porto - FEUP. Through this work, it is possible to strengthen and reaffirm that 3D printing with earth-based mortar has significant potential in the construction industry and that the incorporation of dispersed kraft paper fibres from the recycling of cement bags is an excellent resource to achieve good constructability in 3D printing with earth-based mortar.

Precipitation processes are technologies commonly used in hydrometallurgical plants to recover metals or to treat wastewaters. Moreover, solid-liquid separation technologies, such as thickening or filtering, are relevant unit operations, included in the precipitation technologies. These methods are strongly dependent on the characteristics of the solid precipitates formed during the specific precipitation reaction. One of these characteristics is the particle size distribution (PSD) of the solid precipitates which are fed into a solid-liquid separation process. Therefore, PSD determination is a typical practice for the characterization of the slurries generated in a precipitation plant. Furthermore, the precipitates generated in these processes have a colloidal or aggregation behavior, depending on the operational conditions. Nevertheless, the conventional methods used to estimate PSD (e.g., laser diffraction and/or ciclosizer) have not been designed to measure particles that tend to aggregate or disaggregate, since they include external forces (e.g., centrifugal, agitation, pumping and sonication). These forces affect the true size of the aggregates formed in a unit operation, thereby losing representativity in terms of aggregates particle size. This study presents an alternative method of measuring the size distribution of particles with aggregation behavior, particularly, by using non-invasive microscopy and image processing and analysis. The samples used have been obtained from an experimental precipitation process by applying sulfidization to treat the cyanide-copper complexes contained in a cyanidation solution. This method has been validated with statistical tools and compared with a conventional analysis based on laser diffraction. Our results show significant differences between the methods analyzed, demonstrating that image processing and analysis by microscopy is an excellent and non-invasive alternative to obtaining size distribution of aggregates in precipitation processes.

Glial cell line-derived neurotrophic factor GDNF is among the strongest dopamine neuron function and survival promoting factors known. Due to this reason, it has clinical relevance in dopamine disorders such as Parkinson’s disease and Schizophrenia. In the striatum, GDNF is exclusively expressed in interneurons which make up only about 0.6% of striatal cells. Despite clinical significance, histological analysis of striatal GDNF system arborization and relevance to incoming dopamine axons, which bear its receptor RET, has remained enigmatic. This is mainly due to the lack of antibodies able to visualize GDNF and RET positive cellular processes; here we overcome this problem by using knock-in marker alleles. We find that GDNF neurons chemoattract RET+ axons at least 7 times longer in distance than medium spiny neurons (MSNs), which make up 95% of striatal neurons. Furthermore, we provide evidence that tyrosine hydroxylase, the rate limiting enzyme in dopamine synthesis, is enriched towards GDNF neurons in the dopamine axons. Finally, we find that GDNF neuron arborizations occupy approximately twelve times less striatal volume than 135 times more abundant MSNs. Collectively, our results improve our understanding of how endogenous GDNF affects striatal dopamine system function.

Infant malnutrition remains as an important cause of death and disability, Haiti has the highest prevalence in America, so preventive strategies are needed. Our objective was to assess infant and young children malnutrition in Haiti and to study an association to World Health Organization (WHO) recommended feeding practices adherence. Cross-sectional study of children younger than 2 years old, recruited at Saint Espri Health Center, Port Au Prince (August to September 2014). We registered feeding practices, social and demographic data, and performed anthropometry (WHO-2006 standard). We evaluated 278 infants and young children, 8.08 ± 6.5 months old, 53.2% female. 18.35% had underweight; 13.31% were stunted and 13.67% had moderate or severe wasting. Malnutrition was associated to male gender, older age, lower education of mothers and higher number of siblings. The adherence to WHO recommended practices for breastfeeding was from 11.8 to 97.9% and was related to a lower prevalence of malnutrition. For complementary food, adherence was 9.7 to 90.3%, also associated to lower malnutrition. Conclusion: Prevalence of infant and young children malnutrition in this Haitian Health Center population was high, related to some risk factors. The adherence to WHO recommended feeding practices was associated to a better nutritional status.

CAD-CAE software companies have introduced numerous tools aimed at facilitating topology optimization through Finite Element Simulation, thereby enhancing accessibility for designers via user-friendly interfaces. However, the imposition of intricate constraint conditions or additional restrictions during calculations may introduce instability into the resultant outcomes. In this paper, an algorithm for updating the design variables called Adaptive Variable Design is proposed to keep the final design space volume of the optimized part always under the target value while giving the main algorithm multiple chances to update the optimization parameters and search for a valid design. This algorithm aims to producing results that are more conducive to manufacturability and potentially more straightforward in interpretation. A comparison between several commercial software and the proposed algorithm, implemented in MATLAB, is carried out to prove the robustness of the latter. By simulating identical parts under similar conditions, we seek to generate comparable results and underscore the advantages stemming from the adoption and comprehension of the proposed topology optimization methodology. Our findings reveal that the integrated enhancements within MATLAB pertaining to the topology optimization process yield favourable outcomes with respect to discretization, and the manufacturability of resultant geometries. Furthermore, we assert that the methodology evaluated within MATLAB holds promise for potential integration into commercial packages, thereby enhancing the efficiency of topology optimization processes.

From the aerial parts of Salvia ballotiflora, eleven diterpenoids were isolated, among them, four icetexanes, and one abietane (1–5), which are first reported. Their structures were established by spectroscopic means, mainly ¹H and ¹³C NMR, including 1D and 2D homo- and hetero-nuclear experiments. Most of the isolated diterpenoids were tested for their antiproliferative, anti-inflammatory, and radical scavenging activities using the sulforhodamine B assay on six cancer cell lines, the TPA induced ear edema test in mice, and the reduction of the DPPH assay, respectively. Some diterpenoids showed anti-proliferative activity, these being icetexanes 6 and 3, which were the most active with IC₅₀ (µM) = 0.27 ± 0.08 and 1.40 ± 0.03, respectively, for U251 (human glioblastoma) and IC₅₀ (µM) = 0.0.46 ± 0.05, and 0.82 ± 0.06 for SKLU-1 (human lung adenocarcinoma), when compared with adriamycin (IC₅₀ (µM) = 0.08 ± 0.003, and 0.05 ± 0.003, as the positive control, respectively. Compounds 3 and 10 showed significant reduction of the induced ear edema of 37.4 ± 2.8 and 25.4 ± 3.0% (at 1.0 µmol/ear), respectively. Compound 4 was the sole active diterpenoid in the antioxidant assay (IC₅₀ = 98. 4 ± 3.3), using α-tocopherol as positive control, IC₅₀ (µM) = 31.7 ± 1.04. The diterpenoid profile found is of chemotaxonomic relevance and reinforces the evolutionary link of S. ballotiflora with other members of the section Tomentellae.

The mechanisms underlying the establishment of asymmetric structures during development remain elusive. The wing of Drosophila is asymmetric along the Anterior-Posterior (AP) axis, despite that its growth signals that drive its growth are presumably symmetric. Here, we investigated the contribution of cell recruitment, a process that drives wing fate differentiation in Drosophila, to the asymmetric shape and pattern of the adult wing. Genetic impairment of cell recruitment results in a significant reduction in adult wing asymmetry, primarily affecting the region between longitudinal vein 5 and the wing margin (L5-M). Morphometric analysis reveals that the lack of cell recruitment results in a more symmetric wing with respect to the AP, suggesting a contribution of cell recruitment to the establishment of asymmetry in the adult wing. A close examination of the expression of the wing selector gene vestigial (vg) in wing disc does not support this hypothesis. However, the circularity of the Vg pattern significantly increase in recruitment-impaired wing disc, suggesting that while the decrease of the L5-M region in the adult wing may not be attributed to cell recruitment, it could contribute to the overall asymmetry of the adult wing. We conclude that cell recruitment, a widespread mechanism that participates in growth and patterning of several developing systems, could drive, at least partially, the asymmetric shape of the Drosophila wing.

Building deep learning models proposed by third parties can become a simple task when specialized libraries are used. However, a great deal of mystery still surrounds the design of new models or the modification of existing ones. These tasks require in-depth knowledge of the different components or building blocks as well as their dimensions. This information is limited and broken up in different literature. In this article, we collect and explain in-depth the building blocks to design deep learning models, starting from the artificial neuron to the concepts involved in building deep neural networks. Furthermore, the implementation of each building block is exemplified using the Keras library.

A study of the water quality of the Adolfo López Mateos Reservoir (ALMD) was developed through different indicators from a spatial and seasonal perspective. Variables related to the general characteristics of water quality, trophic level and ecological risk were assessed through the water Quality Index (WQI_NSF-BROWN), Trophic State Index (TSI_CARLSON) and the Ecological Risk Index (RI_HAKANSON). Using data from physical, chemical and biological parameters obtained from four sampling points in the ALMD, the water quality was assessed in each model used. The results indicated that the reservoir presents a water quality classified as “medium” (WQI_NSF-BROWN = 70), where significant variations in the concentrations of some parameters are observed. The reservoir showed a general trophic state classified as “Mesotrophic” (TSI_{GENERAL-AVERAGE} = 43.04). The ecological risk analysis achieved the best classification of the methodology, discarding contamination by heavy metals in surface waters. Through this type of applied methodologies will help as decision making tools in the dam, as well as for application in other dams in the region.

Eating disorders (ED) are characterized by alterations in eating behavior. The genetic factors shared between ED diagnoses have been underexplored. The present study aimed to perform a genome-wide association study on individuals with disordered eating behaviors in the Mexican population, blood methylation quantitative trait loci (blood-meQTL) analysis, and in silico function prediction by different algorithms. The analysis included a total of 1803 individuals. Genome-wide association study and blood-meQTL analysis were performed by logistic and linear regression. In silico functional variant prediction, phenome-wide, and transcriptome-wide association studies by different algorithms were analyzed. In the genome-wide association study, we identified 44 single-nucleotide polymorphisms (SNP) associated at a nominal value and 7 blood-meQTL at a genome-wide umbral. The SNPs were enriched in genome-wide associations of the metabolic and immunologic domains. In the in silico analysis, the SNP rs10419198 located on an enhancer mark could change the expression of PRR12 on blood, adipocytes, and brain areas that regulate food intake. The present study supports the previous associations of genetic variation in the metabolic domain with ED.

Non-coding RNAs (ncRNAs) comprise a diverse class of non-protein coding transcripts that regulate critical cellular processes associated with cancer. Advances in RNA-sequencing (RNA-Seq) have led to the characterization of non-coding RNA expression across different types of human cancers. Through comprehensive RNA-Seq profiling, a growing number of studies demonstrate that ncRNAs, including long non-coding RNA (lncRNAs) and microRNAs (miRNA), play central roles in progenitor B-cell Acute Lymphoblastic Leukemia (B-ALL) pathogenesis. Furthermore, due to their central roles in cellular homeostasis and their potential as biomarkers, the study of ncRNAs continues to provide new insight into the molecular mechanisms of B-ALL. This article reviews the ncRNA signatures reported for all B-ALL subtypes, focusing on technological developments in transcriptome profiling and recently discovered examples of ncRNAs with biologic and therapeutic relevance in B-ALL.

A remarkable strengths of deep neural networks lies in their ability to discover patterns and representations from complex data. Deep learning models can learn and refine features at different levels of abstraction, enabling them to handle complex tasks in computer vision recognition, natural language processing, and speech recognition. The ability to generalize from examples, coupled with the capacity to process vast amounts of data, empowers deep learning to achieve state-of-the-art results across a wide spectrum of applications. An argument for this ability is based on similarities between deep neural networks and the nervous system. In this report, we argue that despite the remarkable performance of deep learning, there are still gaps between deep learning and the nervous system that needs to be closed to enable deep learning doing tasks that currently only the nervous system can perform

Pyrolysis is a combustion process of woody biomass conducted under low or no oxygen conditions. New innovations and the need to limit open burning has resulted in numerous mobile and fixed plant pyrolysis methods that burn a variety of woody residues. Production technologies that reduce the need for open burning, the main source of potential pollutants, fall under the regulations in the Clean Air Act of 1990. This Act is the legal instrument to regulate air pollution at its source across the United States of America and it is implemented and enforced through the Environmental Protection Agency, in coordination with sister agencies. One newer innovation for reducing woody residues and emissions is an air curtain incinerator. Currently, the Clean Air Act regulates stationary solid waste incinerators, and this is also applied to mobile air curtain incinerators burning woody biomass. However, other woody biochar production methods (e.g., flame cap kilns) are not subject to these regulations. Discrepancies in the interpretation of definitions related to incineration and pyrolysis and the myriad of differences related to stationary and mobile air curtain incinerators, type of waste wood from construction activities, forest residues, and other types of clean wood make the permitting regulations confusing as permits can vary by jurisdiction. This review summarizes the current policies, regulations, and directives related to in-woods biochar production and the required permits.

Pencil-beam Doppler scatterometers are a promising remote sensing tool for measuring ocean vector winds and currents from space. While several point designs exist in the literature, these designs have been constrained by the hardware they inherited, and the design is sub-optimal. Here, I present guidelines to optimize the design of these instruments starting from the basic sensitivity equations. Unlike conventional scatterometers or pencil-beam imagers, appropriate sampling of the Doppler spectrum and optimizing the radial velocity error lead naturally to a design that incorporates a pulse-to-pulse separation and pulse length that vary with scan angle. Including this variation can improve radial velocity performance significantly and the optimal selection of system timing and bandwidth is derived. Following this, optimization of the performance based on frequency, incidence angle, antenna length, and spatial sampling strategy are considered. It is shown that antenna length influences the performance most strongly, while the errors depend only on the square root of the transmit transmit power. Finally, a set of example designs and associated performance are presented.

This work addresses the challenge of EEG visual multiclass classification into 40 classes for Brain-Computer interface applications, by using deep learning architectures. The visual multiclass classification approach offers BCI applications a significant advantage, since it allows the supervision of more than one BCI interaction, considering that each class label supervises a BCI task. However, because of the nonlinearity and nonstationarity of EEG signals, performing multiclassifiers based on EEG features remains a significant challenge for BCI systems. In the present work, mutual information-based discriminant channel selection and Minimum-Norm Estimate algorithms are implemented to select discriminant channels and enhance EEG data. Hence, deep EEGNet and Convolutional-recurrent neural networks are implemented separately to classify EEG data of image visualization into 40 labels. By using the k-fold cross-validation approach, average classification accuracies of 94.8% and 89.8% were obtained by implementing the aforementioned network architectures, respectively. Satisfactory results obtained with this method offer a new implementation opportunity for multi-task BCI applications by utilizing a reduced number of channels (&lt;50%), compared to those presented in the related literature where the whole set of channels is used.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

The importance of knowing the advance time in drip irrigation lines lies in its precision, as this influences the proper management of water and nutrients delivery. The mathematical calculation to determine the advance time is based on the general hydraulic flow equation, which relates the fluid velocity and the cross-sectional area of the pipe to the volume of water flowing through it. However, in irrigation pipes, where the flow is a mixture of dripper properties, its pressure, the approach to solving the advance time is different, as it is the sum of individual advance times for each segment. To address this issue, Python 3.11 was used along with various libraries such as Pandas, NumPy, Matplotlib, Seaborn, and Scikit-learn to create a modeling environment and run algorithms that could predict outcomes. A program was developed that calculates the advance time for each segment of the drip line using partial velocities, and a dataset was generated that was used to train and test machine learning models. Several machine learning algorithms such as Linear Regression, Support Vector Machines (SVM), K-Nearest Neighbors (KNN), Decision Trees, and Random Forests were implemented to predict the advance time. Additionally, SciPy optimize was used to obtain multivariable equations that describe the advance time in drip irrigation lines. Results showed that the dripper flow has the greatest influence on the advance time, followed by the diameter and distance. Decision Tree and SVM models had the best accuracy with scores above 98%. Equations were found to calculate the advance time in the complete drip line and in 95% of its length, with coefficients of determination close to 99.33%. This study demonstrated the importance of understanding the relationship between dripper parameters and travel time in drip irrigation, as well as the utility of machine learning and optimization tools for predicting and modeling this phenomenon.

The aim of the present study was to investigate whether chronic undernutrition modifies the response to rostafuroxin in juvenile rats. Chronic undernutrition was induced in male rats using a multideficient diet known as Regional Basic Diet (RBD), mimicking alimentary habits in impoverished regions worldwide. Animals were given RBD – or a control/CTRL normal diet for rodents – from weaning to 90 days, and rostafuroxin (1 mg/kg body mass) or vehicle were orally administered during the last 30 days. Undernourished rats became hypertensive at 55–60 days of age (tail-cuff recording). During the last two days, the rats were hosted in metabolic cages to measure food/energy, water, Na⁺ ingestion, and urinary volume. Blood and kidneys were collected after euthanasia. Rostafuroxin increased food/energy and Na⁺ intake in CTRL and RBD rats but had opposite effects on Na⁺ balance (intake minus urinary excretion): negative in CTRL and positive in RBD. The drug normalized the decreased plasma Na⁺ concentration found in RBD rats, increased urinary volume in RBD but not in CTRL, and decreased and increased urinary Na⁺ concentration in the RBD and CTRL groups, respectively. Rostafuroxin decreased the ouabain-sensitive (Na⁺+K⁺)ATPase and increased the ouabain-resistant, furosemide-sensitive Na⁺-ATPase from proximal tubule cells in both groups, and normalized the systolic blood pressure in RBD without effect in CTRL rats. We conclude that chronic undernutrition modifies the response of blood pressure, caloric metabolism, Na⁺ distribution in liquid compartments, mobilization of Na⁺ from non-osmotic compartments, Na⁺ and water balance, and activity of renal Na⁺-transporting ATPases to rostafuroxin.

Exercise induced bronchoconstriction (EIB) is a common complication of athletes and individuals who exercise regularly. It is estimated that about 90% of patients with underlying asthma experience EIB. Sex differences in the prevalence of asthma have been widely reported, with higher rates in boys vs. girls before puberty, and higher rates in women than men after puberty. Because atopy has been reported to occur at higher rates in athletes than in non-athletes, in this study we investigated sex differences in EIB and atopy in athletes. A systematic literature review identified 60 studies evaluating EIB and/or atopy in post-pubertal adult athletes (n=7501). Collectively, these studies reported: 1) a 23% prevalence of EIB in athletes; 2) a higher prevalence of atopy in male athletes vs. females; 3) a higher prevalence of atopy in athletes with EIB; and 4) a significantly higher rate of atopic EIB in male vs. female athletes. Our analysis indicates that the physiological changes that occur during exercise may differentially affect male and female athletes, and suggest an interaction between male sex, exercise, and atopic status in the course of EIB. Understanding these sex differences is important to provide personalized management plans to athletes with underlying asthma and/or atopy.

The stimulus-secretion coupling of glucose-induced release is generally attributed to the metabolism of the hexose in the β-cells in the glycolytic pathway and the citric acid cycle. Glucose metabolism generates an increased cytosolic concentration of ATP and of the ATP/ADP ratio that closes the ATP-dependent K+-channel at the plasma membrane by the interaction of ATP with the regulatory Kir6.2 channel subunit The resultant depolarization of the β-cells opens voltage-dependent Ca2+-channels at the plasma membrane that allow an increase of the cytosolic cation concentration that triggers the exocytosis of insulin secretory granules. The resultant secretory response evolves in time as a biphasic secretion with a first and transient peak of approximately 10 minutes duration followed by a sustained phase of secretion lasting as long as the stimulus. Whereas the first transient peak can be reproduced by a simple depolarization of β-cells with high extracellular KCl maintaining the KATP-channels open with diazoxide, the sustained phase is agreed to depend on the participation of some metabolic signal that remains to be determined Our group has been investigating for several years the participation of β-cell GABA metabolism, together with that of glucose (the β-cell “specific” nutrient secretagogue) and some other “metabolic” secretagogues (branched-chain alpha-ketoacids and a mixture of L-Leucine + L-glutamine, at supraphysiological concentrations) in their mechanism of stimulation of insulin secretion. All three types of stimuli promote the flux in the GABA shunt of rat islets by different metabolic pathways that end in the production of α-ketoglutarate. This citric acid cycle intermediary is preferentially derived to the GABA shunt instead of its continuous oxidation in the citric acid cycle. Islet content of GABA is significantly suppressed by all the stimuli and blocking the GABA shunt with gabaculine, or ϒ-vinyl-GABA (GABAT inhibitors), diminish the insulin secretory responses as well as total ATP and the ATP/ADP ratio. It is concluded that GABA metabolism is increased in parallel to glucose metabolism and is significantly contributing to the magnitude of the insulin secretory response. Its possible implication in β-cells degradation in type-2 (perhaps also in type 1) diabetes is suggested.

New flaxseed cultivars differing in seed mucilage content (MC) with low hull content (HC) represent an attractive option to simultaneously target the food and feed markets. Here, a genome-wide association study (GWAS) was conducted for MC and HC in 200 diverse flaxseed accessions genotyped with 1.7 million SNP markers. The data obtained for MC and HC indicated a broad phenotypic variation and high (~70%) and a moderate (~49%) narrow sense heritability, respectively. MC and HC did not differ statistically between fiber and oil morphotypes, but yellow-seeded accessions had 2.7% less HC than brown-seeded ones. The genome wide linkage disequilibrium (LD) decayed to r2 = 0.1 at a physical distance of ~100 Kb. Seven and four QTL were identified for MC and HC, respectively. Promising candidate genes included Linum usitatissimum orthologs of the Arabidopsis thaliana genes TRANSPARENT TESTA 8, SUBTILISIN-LIKE SERINE PROTEASE, GALACTUROSYL TRANSFERASE-LIKE 5, MUCILAGE-MODIFIED 4, AGAMOUS-LIKE MADS-BOX PROTEIN AGL62, GLYCOSYL HYDROLASE FAMILY 17 and UDP-GLUCOSE FLAVONOL 3-O-GLUCOSYLTRANSFERASE that have been shown to play a role in mucilage synthesis and release, seed coat development and anthocyanin biosynthesis in A. thaliana were identified. The favorable alleles will be useful in flaxseed breeding towards the goal of achieving the ideal flaxseed cultivars for food and feed by genomic-based breeding.

The Mexican Soil Mesh (MSMx) web service emerges as a pivotal tool for researchers, farmers, and policymakers in the efficient management of extensive soil databases. Built on a responsive and intelligent web design, MSMx synchronizes seamlessly with the SQL language, allowing users to selectively download variables tailored to their studies at the desired spatial scale. The programmatic structure enhances query speed, optimizes development times, and incorporates satellite programming modules for effective handling of the vast soil dataset. This paper high-lights the key features, benefits, and applications of MSMx, emphasizing its role in facilitating data-driven decision-making processes and promoting sustainable soil management practices on the continental shelf of Mexico.

Chronic obstructive pulmonary disease (COPD) is a multifactorial lung inflammatory disease affecting 174 million people worldwide, with a recently reported increased incidence in female patients. Patients with COPD are especially vulnerable to the detrimental effects of environmental exposures, especially from air particulate and gaseous pollutants. Exposure to air pollution severely influences COPD outcomes, resulting in acute exacerbations, hospitalizations, and death. In the current study, we conducted a review of the literature addressing air pollution induced acute exacerbations of COPD (AECOPD) in order to determine whether air pollution affects COPD patients in a sex-specific manner. We found that while the majority of studies enrolled both male and female patients, only a few reported results disaggregated by sex. Most studies had a higher enrollment of male patients, only four compared AECOPD outcomes between sexes, and only one study identified sex differences in AECOPD, with females displaying higher rates. Overall, our analysis of the literature confirmed that air pollution exposure is a trigger for AECOPD hospitalizations and revealed a significant gap in our knowledge of sex-specific effects of air pollutants on COPD outcomes, highlighting the need for more studies considering sex as a biological variable.

UNESCO highlights socio-emotional, cognitive, and behavioral learning as critical for advancing sustainability. As major events, sports generate significant social, economic, and environmental impacts. This study analyzed how academic background, gender, age, sport type, and modality influenced elite Colombian Olympic and Paralympic athletes' socio-emotional competencies. Methods: Colombian elite athletes who were members of the “Support to the Excellence Coldeportes Athlete” participated in the study. The total population studied included 334 Colombian elite athletes: mean age 27.10 ± 6.57 years old with 13.66 ± 6.37 years practicing his/her sports modality. The socio-emotional competencies of the participants were assessed using the Socio-emotional Competencies Scale (SECS). Results: Men scored higher in interpersonal regulation, self-awareness, conflict resolution, and emotional regulation. Younger athletes (≤25 years) had higher self-consciousness. Individual versus team sports did not differ. Paralympians showed higher motivation, self-awareness, teamwork, and emotional regulation. University educated athletes scored higher in motivation, self-awareness, teamwork, and empathy. All competencies positively correlated. Conclusion: Individualized interventions targeting improved socio-emotional performance are vital for sustainability and should account for differences across gender, age, education, and disability status.

The aim of the present study was to investigate whether chronic undernutrition modifies the response to rostafuroxin in juvenile rats. Chronic undernutrition was induced in male rats using a multideficient diet known as Regional Basic Diet (RBD), mimicking alimentary habits in impoverished regions worldwide. Animals were given RBD – or a control/CTRL normal diet for rodents – from weaning to 90 days, and rostafuroxin (1 mg/kg body mass) or vehicle were orally administered during the last 30 days. Undernourished rats became hypertensive at 55–60 days of age (tail-cuff recording). During the last two days, the rats were hosted in metabolic cages to measure food/energy, water, Na+ ingestion, and urinary volume. Blood and kidneys were collected after euthanasia. Rostafuroxin increased food/energy and Na+ intake in CTRL and RBD rats but had opposite effects on Na+ balance (intake minus urinary excretion): negative in CTRL and positive in RBD. The drug normalized the decreased plasma Na+ concentration found in RBD rats, increased urinary volume in RBD but not in CTRL, and decreased and increased urinary Na+ concentration in the RBD and CTRL groups, respectively. Rostafuroxin decreased the ouabain-sensitive (Na++K+)ATPase and increased the ouabain-resistant, furosemide-sensitive Na+-ATPase from proximal tubule cells in both groups, and normalized the systolic blood pressure in RBD without effect in CTRL rats. We conclude that chronic undernutrition modifies the response of blood pressure, caloric metabolism, Na+ distribution in liquid compartments, mobilization of Na+ from non-osmotic compartments, Na+ and water balance, and activity of renal Na+-transporting ATPases to rostafuroxin.

We aimed to delineate cardiopulmonary interactions in acute bronchiolitis and to evaluate the capacity of a combined cardiopulmonary ultrasonography to predict the need for respiratory support. This was a prospective observational single-center study that includes infants < 12 month of age admitted to a hospital due to acute bronchiolitis. All the included patients under-went clinical, laboratory and cardiopulmonary ultrasonographic evaluation at the same time point within 24 hours of hospital admission. The existence of significant correlation between car-diac and respiratory parameters was the primary outcome. The association of different cardio-pulmonary variables with the need of respiratory support higher than O2, the length of stay hos-pitalization, the PICU stay, and the duration of respiratory support were a secondary outcome. We enrolled 112 infants (median age 1 (0.5-3) months; 62% males) hospitalized with acute bron-chiolitis. Increased values of the pulmonary variables (BROSJOD score, pCO2 and LUS) showed moderate correlations with NT-proBNP and all echocardiographic parameters indicative of pulmonary hypertension and myocardial dysfunction. Up to 36 (32%) infants required respira-tory support during the hospitalization. This group presented with higher lung ultrasound score (p<0.001), and increased values of Tei index (p<0.001) and pulmonary artery pressures (p<0.001). All the analyzed respiratory and cardiac variables showed moderate to strong correlations with the LOS hospitalization and the time of respiratory support. Lung ultrasound and echocardiog-raphy showed a moderate to strong predictive accuracy for the need of respiratory support in the ROC analysis, with AUC varying from 0.74 to 0.87. Conclusion: Those cases of bronchiolitis with a worse pulmonary status presented with a more impaired cardiac status. Cardiopulmonary ul-trasonography could be a good strategy to easily identify high-risk population for a complicated acute bronchiolitis hospitalization.

Ocean surface currents and winds are tightly coupled essential climate variables, and, given their short time scales, observing them at the same time and resolution is of great interest. DopplerScatt is an airborne Ka-band scatterometer that has been developed under NASA's Instrument Incubator Program (IIP) to provide a proof of concept of the feasability of measuring these variables using pencil-beam scanning Doppler scatterometry. In the first half of this paper, we present the Doppler scatterometer measurement and processing principles, paying particular attention to deriving a complete measurement error budget. Although Doppler radars have been used for the estimation of surface currents, pencil-beam Doppler Scatterometry offers challenges and opportunities that require separate treatment. The calibration of the Doppler measurement to remove platform and instrument biases has been a traditional challenge for Doppler systems, and we introduce several new techniques to mitigate these errors when conical scanning is used. The use of Ka-band for airborne Doppler scatterometry measurements is also new, and, in the second half of the paper, we examine the phenomenology of the mapping from radar cross section and radial velocity measurements to winds and surface currents. To this end, we present new Ka-band Geophysical Model Functions (GMF's) for winds and surface currents obtained from multiple airborne campaigns. We find that the wind Ka-band GMF exhibits similar dependence to wind speed as that for Ku-band scatterometers, such as QuikSCAT, albeit with much greater upwind-crosswind modulation. The surface current GMF at Ka-band is significantly different from that at C-band, and, above 4.5 m/s has a weak dependence on wind speed, although still dependent on wind direction. We examine the effects of Bragg-wave modulation by long waves through a Modululation Transfer Function (MTF), and show that the observed surface current dependence on winds is consistent with past Ka-band MTF observations. Finally, we provide a preliminary validation of our geophysical retrievals, which will be expanded in subsequent publications. Our results indicate that Ka-band Doppler scatterometry could be a feasible method for wide-swath simultaneous measurements of winds and currents from space.

Databases are by far the most valuable asset of companies. Since the need was seen not only to count but also to have some type of record of elements such as crops, animals, money, properties and that this record could be consulted and modified according to the situation, that is where the first database was born. , and after that, these databases cannot be disorganized, they also need to be managed and administered under established standards that facilitate their understanding and management not only by their creators but by the other people who subsequently administer them. Databases and database management systems have an interesting evolutionary history that deserves to be analyzed and this is the objective of this document, where it is sought to understand. Along with databases and their management systems, data mining or Data mining arises that in order not to extend ourselves so much, it is the job of finding common patterns in various data sources and in what way they can be used to predict situations or results of various circumstances; We also focus on the other topic that we will present, Oracle data mining, which roughly is to merge data mining with Oracle, which makes it a powerful tool for obtaining information and predicting results based on statistics.In this article we will study and analyze the ideas, concepts and basic examples that make up SGBD and Data Mining and, we will try to go deeper into this topic, the use of decision techniques such as advanced statistical algorithms. We also present a fictitious example of the application of these techniques: predicting which products can be sold based on their relationship with others. we will give a brief explanation of association rules, data mining cycle and the types of learning and the evolution that data mining has had.

In a constantly changing environment brought about by the climate crisis and escalated anthropogenic perturbations driven by the growing population, harmful algal bloom dynamics and their impacts are expected to shift, necessitating adaptive management strategies and comprehensive research efforts. Similar to primary productivity, HABs have been thought to be driven primarily by major nutrients such as N, P, and Si. However, recent investigations on the role and importance of micronutrients as limiting factors in aquatic environments have been highlighted. This paper provides a review of metal and phytoplankton interactions, with a specific emphasis on pertinent information on the influence of trace nutrients on growth, toxin production, and other underlying mechanisms related to the dynamics of HABs. Low to near-depleted levels of essential nutrients including Fe, Cu, Zn, Se, Mn, Co, and Mo, negatively impact cell growth and proliferation of various marine and freshwater HAB species. However, evidence shows that at elevated levels, these trace elements along with other non-essential ones, could still cause toxic effects to certain HAB species manifested by decreased photosynthetic activities, oxidative stress, ultrastructure damage, and cyst formation. Interestingly, while elevated levels of these metals mostly result in increased toxin production, Co (i.e., yessotoxins, gymnodimine, and palytoxins) and Mn (i.e., isodomoic acid, okadaic and diol esters) enrichments revealed otherwise. In addition to toxin production, releasing dissolved organic matter (DOM) including dissolved organic carbon (DOC) and humic substances was observed as an adaptation strategy, since these organic compounds have been proven to chelate metals in the water column, thereby reducing metal-induced toxicity. Whilst current research center on free metal toxicity of specific essential elements such as in Cu and Zn, a comprehensive account of how trace metals contribute to the growth, toxin production, and other metabolic processes under conditions reflective of in-situ scenarios of HAB-prone areas, would yield new perspectives on the roles of trace metals in HABs. With the growing demands of the global population for food security and sustainability, substantial pressure is exerted on the agriculture and aquaculture sector, highlighting the need for effective communication of information regarding the interactions of macro- and micronutrients with HABs to improve existing policies and practices.

Corruption is a legal and moral contravention that generates great concern among nations due to its erosive effects on economic growth, democracy, governance, social equity and the integrity of culture. Therefore, it is necessary to know more about the multiple variables that produce and maintain this phenomenon. This article reports the results of an experimental investigation that sought to provide elements of judgment on the influence of the structure of personal values ​​on the willingness to bribe. For this, 12 couples of young university students of both sexes interacted through a game that simulated a relationship between a corrupter and a corruptible agent, with the help of a real-time communication system, mediated by an online platform, which allowed instant and bidirectional interaction. The couples were randomly constituted and played with each other under double blind. However, the interacting members of the dyad could share values ​​or vary in their axiological structure in such a way that, while one of them could manifest anti-corruption principles, the other's commitment was not so obvious. The results confirm the importance of the axiological structure of people in the facilitation or containment of the corrupt behavior. This article also reflects on the theoretical connotations of the relationships shown.

In this article, we propose a circuit to imitate the behavior of a Reward-Modulated Spike-Timing-Dependent Plasticity synapse. When two neurons in adjacent layers produce spikes, each spike modifies the thickness of the common synapse. As a result, the synapse’s ability to conduct impulses is controlled, leading to an unsupervised learning rule. By introducing a reward signal, reinforcement learning is enabled by redirecting the growth and shrinkage of synapses based on signal feedback from the environment. The proposed synapse manages the convolution of the emitted spike signals to promote either the strengthening or weakening of the synapse, which is represented as the resistance value of a memristor device. As memristors have a conductance range that may differ from the available current input range of typical CMOS neuron designs, the synapse circuit can be adjusted to regulate the spike’s amplitude current to comply with the neuron. The circuit described in this work allows for the implementation of fully interconnected layers of neuron analog circuits. This is achieved by having each synapse reconform the spike signal, thus removing the burden of providing enough power from the neurons to each memristor. The synapse circuit was tested using a CMOS analog neuron described in the literature. Additionally, the article provides insight into how to properly describe the hysteresis behavior of the memristor in Verilog-A code. The testing and learning capabilities of the synapse circuit are demonstrated in simulation using the Skywater-130nm process. The article’s main goal is to provide the basic building blocks for Deep Neural Neural Networks relying on spiking neurons and memristors as the basic processing elements to handle spike generation, propagation, and synaptic plasticity.

The present work aims at the comprehensive application of stochastic and optimization tools with the support of Information and Communication Technologies (ICT) through a case study in a logistics process for electronic goods; simulation and Response Surface Methodology (RSM) are applied for this purpose. The problem to be evaluated is to define an optimal distribution cost for products shipped to wholesale customers located in different cities in Mexico from a manufacturing plant in Tijuana, Mexico. The factors under study are the product allocation for each distribution center, finished good inventory level and on time deliveries, which are supposed to be significant to get the objective. The methodology applied for this problem considers the design of a discrete event simulation model to represent virtually the real life of logistics process, which is considered a complex system due to different activities are interrelated to carry it out. This model is used to execute the different experiments proposed by the RSM. The results obtained from simulation model were analyzed with the RSM to define the mathematical model that allows identifying the parameters of the factors in order to optimize the process. The findings prove how the ICT facilitate the application of stochastic tools with the purpose of process optimization.

Abstract: Nowadays, there is an increasing interest in the development of novel bioresorbable membranes for Guided Bone Regeneration (GBR). Hydroxyapatite of different resources in com-bination with chitosan has been used successfully. In this work, armored catfish (Pterygoplich-thys spp) bone as a source of hydroxyapatite is proposed; it was isolated through bone calcina-tion at a temperature of 1000 °C. The hydroxyapatite obtained was analyzed for its chemical composition by means of Energy Dispersive Spectroscopy (EDS), its functional groups by Fouri-er Transform Infrared Spectroscopy (FT-IR), its crystallographic structures were analyzed by X-ray diffraction (DRX) and Scanning electron microscopy (SEM) was used to observe the mor-phology of the particle. The composed membrane presents a major roughness morphology sur-face than the pristine chitosan membrane. The hydroxyapatite particles added to the polymeric matrix increased the mechanical tensile properties of the membrane. These findings confirm that armored catfish bones are a viable, economic, and environmentally friendly source of hydroxy-apatite, which combined with chitosan, is a suitable alternative to develop biocompatible GBR membranes after it is combined with chitosan.

Oyster mushroom (Pleurotus ostreatus), nopal (Opuntia ficus-indica) and amaranth (Amaranthus spp.) are pre-hispanic foods widely consumed in Mexico. However, there are no standard products developed with these ingredients as functional cookies. This study evaluated the impact of partial replacement (50%) of whole-wheat flour (WWF) with three formulations of P. ostreatus, nopal and amaranth flours (POF, NF and AF, respectively) in the nutritional/antioxidant properties of fortified cookies. The proportion of flours´ ingredients (WWF:AF:NF:POF) were 100% WWF (traditional cookies), 50:35:10:5 (formulation 1), 50:30:15:5 (formulation 2) and 50:40:5:5 (formulation 3). Proximal composition, phenolic/flavonoid contents, and ABTS+ scavenging activity were determined in flours and cookies. POF, NF and AF possess a high nutritional value comprising polyphenols/flavonoids and a significant antioxidant potential. Total protein, ashes and flavonoids were higher in fortified cookies than controls. Cookies prepared with Formulation 2 -highest nopal level- contained 5.29% of dietary fiber and 5-times higher polyphenol content than control cookies. The ABTS+ scavenging ability was similar in the three enriched cookies (87.73-89.58%) but higher than traditional cookies (75.60%). Applicability of POF/NF/AF for replacing up to 50% of WWF in production of functional cookies was demonstrated. The research promotes renewable local bioresouces for a sustainable agri-food chain, especially edible mushrooms.

Since its initial characterization in 2016, the interferon stimulated gene Shiftless (SHFL) has proven to be a critical piece of the innate immune response to viral infection. SHFL expression stringently restricts the replication of multiple DNA, RNA, and retroviruses with an extraordinary diversity of mechanisms that differ from one virus to the next. These inhibitory strategies include the negative regulation of viral RNA stability, translation, and even the manipulation of RNA granule formation during viral infection. Even more surprisingly, SHFL is the first human protein found to directly inhibit the activity of the -1 programmed ribosomal frameshift, a translation recoding strategy utilized across nearly all domains of life and a several human viruses. Recent literature has shown that SHFL expression also significantly impacts viral pathogenesis in mouse models, highlighting its in-vivo efficacy. To help reconcile the many mechanisms by which SHFL restricts viral replication, we provide here a comprehensive review of this complex ISG, its influence over viral RNA fate, and the implications of its functions on the virus-host arms race for control of the cell.

Parallel manipulators with multiple end-effectors bring us interesting advantages over conventional parallel manipulators such as improved manipulability, workspace and avoidance of singularities. In this work the kinematics of a five-bar planar parallel manipulator equipped with two end-effectors is approached by means of the theory of screws. As an intermediate step the displacement analysis of the robot is also investigated. The input-output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. In that regard the Klein form of the Lie algebra se(3) of the Euclidean group SE(3) plays a central role. In order to exemplify the method of kinematic analysis, a case study is included. Furthermore, the numerical results obtained by means of the theory of screws are confirmed with the aid of special software like ADAMS.^TM

The advent of immunotherapy has revolutionized the treatment of advanced non-small cell lung cancer (NSCLC), improving the prognosis of this disease and becoming a key part of the treatment, especially in the population without an oncogenic driver mutation. Two different groups of immune checkpoint inhibitors (ICIs) are used in lung cancer: Anti- Cytotoxic T-lymphocyte antigen-4 (Anti-CTLA 4) and Anti- T-cell receptor programmed cell death-1 or its ligand (Anti-PD-1 and Anti PD-L1). Here in, we review an uptodate on the use of immunotherapy for advanced NSCLC.

Since the recent legalization of medical and recreational use of cannabis (Cannabis sativa L.) in many regions worldwide, there has been high demand for research to improve yield and quality. With the paucity of scientific literature on the topic, this study investigated the relationships between light intensity (LI) and photosynthesis, inflorescence yield, and inflorescence quality of cannabis grown in an indoor environment. After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈ 425 μmol·m-2·s-1 and an 18-h light/6-h dark photoperiod, plants were grown for 12 weeks in a 12-h light/12-h dark ‘flowering’ photoperiod under canopy-level PPFDs ranging from 120 to 1800 μmol·m-2·s-1 provided by light emitting diodes. Leaf light response curves varied both with localized (i.e., leaf-level) PPFD and temporally, throughout the flowering cycle. Therefore, it was concluded that the leaf light response is not a reliable predictor of whole- plant responses to LI, particularly crop yield. This may be especially evident given that dry inflorescence yield increased linearly with increasing canopy-level PPFD up to 1800 μmol·m-2·s-1, while leaf-level photosynthesis saturated well below 1800 μmol·m-2·s-1. The density of the apical inflorescence and harvest index also increased linearly with increasing LI, resulting in higher-quality marketable tissues and less superfluous tissue to dispose of. There were no LI treatment effects on cannabinoid potency, while there were minor LI treatment effects on terpene potency. Commercial cannabis growers can use these light response models to determine the optimum LI for their production environment to achieve the best economic return; balancing input costs with the commercial value of their cannabis products.

Background/Objectives: Vitamin B12 deficiency can cause variable symptoms, which may be irreversible if not diagnosed and treated in a timely manner. We aimed to develop a widely accepted expert consensus to guide the practice of diagnosing and treating B12 deficiency. Methods: We conducted a scoping review of the literature published in PubMed since January 2003. Data were used to design a two-round Delphi survey to study the level of consensus among 42 experts. Results: The panelists agreed on the need for educational and organizational changes in the current medical practices for diagnosing and treating B12 deficiency. Recognition of clinical symptoms should receive the highest priority in establishing the diagnosis. There is agreement that the serum B12 concentration is useful as a screening marker, whereas methylmalonic acid or homocysteine can support the diagnosis. Patient lifestyle, disease history and medications can provide clues to the cause of B12 deficiency. Regardless of the cause of the deficiency, initial treatment with parenteral B12 was regarded as the first choice for patients with acute and severe manifestations of B12 deficiency. The use of high-dose oral B12 at different frequencies may be considered for long-term treatment. Prophylactic B12 supplementation should be considered for specific high-risk groups. Conclusions: There is a consensus that clinical symptoms need to receive more attention in establishing a diagnosis. B12 laboratory markers can support the diagnosis. The severity of clinical symptoms, the causes of B12 deficiency and the treatment goals govern decisions regarding the route and dose of B12 therapy.

It is commonly believed that exposing Cannabis sativa (cannabis) plants to ultraviolet (UV) radiation can enhance Δ⁹-tetrahydrocannabinol (Δ⁹-THC) concentrations in female inflorescences and associated foliar tissues. However, a lack of published scientific studies has left knowledge-gaps in the effects of UV on cannabis that must be elucidated before UV can be utilized as a horticultural management tool in commercial cannabis production. In this study we investigated the effects of UV exposure level on photosynthesis, growth, inflorescence yield, and secondary metabolite composition of two indoor-grown cannabis cultivars: ‘Low Tide’ (LT) and ‘Breaking Wave’ (BW). After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈225 μmol·m^–2·s^–1 in an 18-h light/6-h dark photoperiod, plants were grown for 9 weeks in a 12-h light/12-h dark “flowering” photoperiod under a canopy-level PPFD of ≈400 µmol·m^–2·s^–1 and 3.5 h·d^–1 of supplemental UV radiation with UV photon flux densities (UV-PFD) ranging from 0.01 to 0.8 μmol·m^–2·s^–1 provided by light-emitting diodes (LEDs) with a peak wavelength of 287 nm (i.e., biologically-effective UV doses of 0.16 to 13 kJ·m^–2·d^–1). The severity of UV-induced morphology (e.g., whole-plant size and leaf size reductions, leaf malformations, and stigma browning) and physiology (e.g., reduced leaf photosynthetic rate and reduced F_v/F_m) symptoms worsened as UV exposure level increased. While the proportion of dry inflorescence yield that was derived from apical tissues decreased in both cultivars with increasing UV exposure level, total dry inflorescence yield only decreased in LT. The equivalent Δ⁹-THC and cannabidiol (CBD) concentrations also decreased in LT inflorescences with increasing UV exposure level. While the total terpene content in inflorescences decreased with increasing UV exposure level in both cultivars, the relative concentrations of individual terpenes varied by cultivar. The potential for using UV to enhance cannabis quality must still be confirmed before it can be used as a production tool for modern, indoor-grown cannabis cultivars.

The World Health Organization identifies alcohol as a cause in several neoplasias of the oro-pharynx cavity, esophagus, gastrointestinal tract, larynx, liver, or female breast. This study re-views ethanol's nonoxidative and oxidative metabolism and one-carbon metabolism that en-compasses both redox and transfer reactions that influence crucial cell proliferation machinery. Ethanol favors the uncontrolled production and action of free radicals that interfere with the maintenance of essential cellular functions. We focus on the generation of protein, DNA, and lipid adducts that interfere with the cellular processes related to growth and differentiation. Ethanol's effects on stem cells responsible for building and repairing tissues are reviewed. Cancer stem cells suffer disturbances related to the expression of cell surface markers, enzymes, and transcription factors after ethanol exposure with consequent dysregulation of mechanisms related to cancer metastasis or resistance to treatments. Our analysis aims to underlie and discuss potential targets that show more sensitivity to ethanol's action and identify specific metabolic routes and metabolic realms that may be corrected to recover metabolic homeostasis after pharmacological interven-tion. Specifically, research should pay attention to reestablish metabolic fluxes by fine-tuning the functioning of specific pathways related to one-carbon metabolism and antioxidant processes.

This study evaluates inequalities in the use of dental services according to place of birth before and after the economic crisis in Spain. A cross-sectional study was performed in the population aged 18 to 65 years in Spain. We used data from three Spanish National Health Surveys for years 2006 (before the crisis), 2014 and 2017 (after the crisis). Log-binomial regression was used to quantify the association between region of origin and use of dental care services before and after controlling for the selected covariates. In 2006, we found a greater probability of not using dental care services in immigrants from Asia (PR:1.36, 95% CI:1.10–1.67) and Africa (PR:1.16; 95% CI:1.05–1.28) compared to the natives. For 2014, the probability of not using dental care services was greater for all immigrants compared to the natives, with the greatest odds for those from Africa (PR:1.71; 95% CI:1.46–2.01) and Asia (PR:1.3; 95% CI:1.23–1. 47). The associations for 2017 were weaker in magnitude than the ones observed for 2014, although stronger than for 2006. This study suggests that the economic recovery did not have the same impact for natives and immigrants regardless of regions of origin, given the observed inequalities in use of dental services.

National heatwave plans are aimed at reducing the avoidable human health consequences due to heatwaves, by providing warnings to and improving communication between relevant stakeholders. The aim of this study was to assess the perceptions of key stakeholders within plans in Belgium and the Netherlands on their responsibilities, the partnerships, and the effectiveness of the local implementation in Brussels and Amsterdam. Key informant interviews were held with stakeholders that had an important role in development of the heatwave plan in these countries, or its implementation in Brussels or Amsterdam. Care organisations, including hospitals and elderly care organisations, had a lack of familiarity with the national heatwave plan in both cities, and prioritised heat the lowest. Some groups of individuals, specifically socially isolated individuals, are not sufficiently addressed by the current national heatwave plans and most local plans. Stakeholders reported that responsibilities were not clearly described and that the national plan does not describe tasks on a local level. We recommend to urgently increase awareness on the impact of heat on health among care organisations. More emphasis needs to be given to the variety of heat risk groups. Stakeholders should be involved in the development of updates of the plans.

Overweight/obesity is a growing pandemic nowadays that affects many organs and tissues. We have investigated whether a high-lipid diet provokes an imbalance between type 1 and type 2 angiotensin II (Ang II) receptors signaling, leading to liver alterations associated with previously described cardiovascular and kidney disturbances. Chronic administration of a high-lipid diet can provoke an hepatocardiorenal syndrome as the result of activation of the Ang II→type 1 receptor axis, which is completely counteracted by Ang-(3–4) the allosteric enhancer of the Ang II→type 2 receptor pathway.

We aimed to provide a comprehensive assessment of exercise physiology of adult Fontan patients (FP) and factors limiting functional capacity (FC). A prospective single-centre study of 37 FP aged ≥16years and 19 healthy-controls (HC), who underwent CPET on cycle-ergometer in February-March 2022. Lung function was impaired in FP, mostly mild restrictive pattern (56.8%). Mean peakVO2 was 21±5.4ml/kg/min, 55% predicted. Morphologically left-single ventricle showed higher peakVO2%predicted (57.4±14.4% vs 43.4±8.1%, p=0.045). A lower peakVO2%predicted was observed in patients with an early flattened and/or descending O2 pulse at maximal exertion (52±14% vs 62±12.5, p=0.04 and 47.6±9% vs 60±14 respectively, p=0.018) and chronotropic insufficiency (53±12% vs 69.8±20%, p=0.008). Strong positive correlation was observed between %OUES and peakVO2%predicted (r=0.726, p>0.001). PeakVO2%predicted was progressively higher as the level of physical activity increased (low-level 49.5±14%, moderate-level 55±12%, intense-level 69±20%). FP showed lower inspiratory muscle strength compared to HC but it was no statistically associated with either peakVO2 or VE/VCO2 slope. In FP OUES is a useful submaximal parameter in those who fail to reach maximal exertion. Chronotropic insufficiency and early flattened or descending oxygen pulse slope were factors associated with low peakVO2. Regular intense physical activity improves FC. Although FP have inspiratory muscle weakness, its impact on FC is unclear.

The importance of rare earth elements as the basis in the development of new technologies or the improvement of the used ones, made of a necessity its recovery, besides that from raw materials, from waste materials. In this recovery, Hydrometallurgy and its derivative Solvometallurgy, play a key role due to its operational characteristics, which are emphasized with the use of ionic liquids. The manuscript reviewed the most recent advances (2023 and 2024 years) about the use of ionic liquids in the unit operations (leaching and separation technologies) aimed to the recovery of these valuable and strategic metals. Moreover, a comprehensive review about the use of these chemicals in the development of advanced materials containing some of these rare earth elements is presented.

Generative AI has gained enormous interest nowadays due to new applications like chatGPT, DALL E, Stable Difussion and Deep Fake. Particularly DALL E, Stable Difussion and others (Adobe Firefly, ImagineArt...) are able to create images from a text prompt and are also able to recreate real photographs. Due to this fact, intense research has arisen to create new image forensics applications able to distinguish between real captured images and videos and artificial ones. Detecting forgeries made with Deep Fake is one of the most researched issues. This paper is about another kind of forgery detection. The purpose of this research aims to detect photo realistic AI created images versus real photos coming from a physical camera. For this purpose, techniques that perform a pixel level feature extraction are used. First one is Photo Response Non-Uniformity (PRNU). PRNU is a special noise due to imperfections on the camera sensor that is used for source camera identification. The underlying idea is that AI images will have a different PRNU pattern. Second one is Error level analysis (ELA). This is other type of feature extraction traditionally used for detecting image editions. In fact, ELA is being used nowadays by photographers to detect manually AI created images. Both kinds of features are used to train Convolutional Neural Networks to differentiate between AI images and real photographs. Good results are obtained achieving accuracy rates over 95%. Both extraction methods are carefully assessed by computing precision/recall and F1-score measurements.

The impact of the presence of Microplastics (Mp's) has become popular due to its presence in all environments, however, its transportation, accommodation and destination is still unknown. This study developed a laboratory-scale experiment, using eco-technologies for the treatment of domestic wastewater and reused for agriculture. A Constructed Wetland System of horizontal subsurface flow conditioned with substrate gravel and with two types of ornamental plants Hippeastrum Hybridum Hort and Heliconia Bihai Marginata, obtained an average 90% efficiency in the removal of pollutants COD, TDS, NH4, NT, PO4 , NO2 and PT; directing water through a drip irrigation system for irrigation of the Phaseolus vulgaris crop, selected for its nutritional importance (36% of daily protein intake), grown in two Growth Beds; The crop irrigated with treated water presented a greater relationship between growth and number of pods; finally identify the presence of Mp's through Fourier transform infrared spectroscopy (FTIR) analysis in the different types of water (domestic waste, treated waste and well) and determine the quality of the fruit for consumption with safety tests. Escherichia coli and Salmonella.

Synthetic chalcomenite-type cupric selenite CuSeO₃∙2H₂O has been studied at room temperature under compression up to pressures of 8 GPa by means of single-crystal X-ray diffraction, Raman spectroscopy, and density-functional theory. According to X-ray diffraction, the orthorhombic phase undergoes an isostructural phase transition at 4.0(5) GPa with the thermodynamic character being first-order. This conclusion is supported by Raman spectroscopy studies which have detected the phase transition at 4.5(2) GPa and by the first-principles computing simulations. The structure solution at different pressures has provided information on the change with pressure of unit-cell parameters as well as on the bond and polyhedral compressibility. A Birch-Murnaghan equation of state has been fitted to the unit-cell volume data. We found that chalcomenite is highly compressible with a bulk modulus of 42 – 49 GPa. The possible mechanism driving changes in the crystal structure is discussed, being the behavior of CuSeO₃∙2H₂O mainly dominated by the large compressibility of the coordination polyhedron of Cu. On top of that, an assignation of Raman modes is proposed based upon density-functional theory and the pressure dependence of Raman modes discussed. Finally, the pressure dependence of phonon frequencies is also reported.

There is significant need for development of a new environmentally friendly, extraction-free sample collection medium that can effectively preserve and protect genetic material for point-of-care, and/or self-collection, home-collection, and mail-back testing. Systematic Evolution of Ligands by Exponential Enrichment (SELEX) was used to create anti-ribonuclease (RNase) Deoxyribonucleic acid (DNA) aptamers against purified RNase A conjugated to paramagnetic carboxylated beads. Following 8 rounds of SELEX carried out under various stringency conditions, e.g., selection using Xtract-Free™ (XF) specimen collection medium, and elevated ambient temperature of 28 ºC, a panel of 5 aptamers was chosen following bioinformatic analysis using next-generation sequencing. The efficacy of aptamer inactivation of RNase was assessed by monitoring Ribonucleic acid (RNA) integrity by fluorometric and real-time RT-PCR analysis. Inclusion of aptamers in reaction incubations resulted in an 8,800 to 11,200-fold reduction of RNase activity, i.e., digestion of viral RNA compared to control. Thus, anti-RNase aptamers integrated into XF collection medium as well as other commercial reagents and kits have great potential for ensuring quality intact RNA for subsequent genomic analysis.

The carbapenemase OXA-244 is a derivate of OXA-48, and its detection is very difficult in laboratories. Here we report the identification and genomic analysis of an Escherichia coli isolate (28Eco12) harbouring the bla_OXA-244 gene identified in Colombia, South America. The 28Eco12 isolate was identified during a retrospective study and it was recovered from a patient treated in Colombia. The complete nucleotide sequence was established using the PacBio platform. A comparative genomics analysis with other bla_OXA-244–harbouring Escherichia coli strains was performed. The 28Eco12 isolate belonged to sequence type (ST) 38 and its genome was composed of two molecules, a chromosome of 5,343,367 bp and a plasmid of 92,027 bp, which belonged to the incompatibility group IncY and did not harbour resistance genes. The bla_OXA-244 gene was chromosomally-encoded and mobilized by an ISR1-related Tn6237 composite transposon. Notably, this transposon was inserted and located within a new genomic island. For our knowledge this is the first report of a bla_OXA-244–harbouring Escherichia coli isolate in American continent.Our results suggest that the introduction of the OXA-244-producing E. coli isolate was through clonal expansion of the ST38 pandemic clone. Other isolates producing OXA-244 could be circulating silently on the American continent.

As sessile organisms, plants face a wide range of abiotic stresses, with salinity being a prominent constraint affecting their growth, development, and productivity, particularly in arid and semi-arid regions. This study focused on understanding how salinity impacts Jatropha curcas, an important oilseed plant for biodiesel production. By examining the anatomy and ultrastructure of stomata and chloroplasts, we investigated the effects of prolonged salinity stress on J. curcas. This stress led to changes in stomatal density, stomatal index, and ostiole aperture, which case an imbalance of water conductivity in the xylem. Through transmission electron microscopy, we explored the subcellular organization of J. curcas chloroplasts and their contribution to plant photosynthetic efficiency, providing insights into their role in this process. Notably, salinity treatment resulted in a significant increase in starch granules accumulation, leading to impaired the granal and stromal grana lamellae, destroying this ultrastructure. Our findings indicate that the anatomy and ultrastructure of chloroplasts play a crucial role in influencing photosynthetic efficiency and hydraulic conductivity. This study offers new perspectives on the structure and function of chloroplasts in J. curcas, presenting innovative opportunities to develop strategies that enhance biofuel production in areas with high soil salinity.

The focus of this work lies in the construction of monitoring system designed in the form of a patch using a long-lasting potentiometric electrolyte concentration sensor from metal electrodes, in a galvanic cell configuration Mg(s)|NaCl(aq)|Cu(s). Initially, a mathematical analysis was conducted on the expected sensor output through the Nernst equation. The experimental phase involved conducting controlled tests in the laboratory using various molar concentrations of sodium chloride (NaCl) in aqueous solution. Results showed that the electrolyte sensor allows for monitoring electrolyte levels in NaCl in the range of 0.02 to 1 M/L, with electrode lifespan exceeding 10 days. On the other hand, when patch is using human sweat during controlled exercise routines, it showed the sensor's capability for monitoring changes in the subjects' hydration levels in real time. The sensor output potential is greater than 1.7 volts when the sensor electrodes are in contact with human sweat, which is equivalent to measuring molar concentrations at normal hydration and moderately high hydration levels. Sensor results indicate that the system can function in a self-powered manner without external batteries. Additionally, the extended lifespan of its electrodes allows for continuous monitoring of imbalances in the human body, showcasing the system capability for long-term health assessment.

In this article, we give a brief review of the origin of the neutrino mass in some interesting non-linear supersymmetric models with R-symmetry. These models are able to address and solve the most important problems of the particle physics and provide mechanisms for neutrino mass generation and their mixing parameters in agreement with the current experimental data. Their prediction could be experimentally tested in the near future by collider experiments.

The practice of physical activity is an effective non-pharmacological strategy for preventing and treating chronic diseases. A large body of evidence has contributed to establishing a positive correlation between a physically active lifestyle and health benefits, including enhanced vaccination responses, lower numbers of senescent T-cells, increased T-cell proliferative capacity, lower levels of inflammatory cytokines, and improved neutrophil and macrophage function. While females are generally thought to exert more robust immune responses than males in response to a variety of challenges, and both male and female sex hormones have been suggested as mediators of immune function, research on this topic has not always been designed with a sex-specific lens. The goal of this review is to summarize the available experimental and clinical evidence linking exercise and immune function in male and female subjects, with an emphasis on sex differences and sex-specific mechanisms. Overall, the available evidence indicates that moderate exercise and physical activity improves immune function in both sexes, whereas prolonged and high-intensity exercise temporarily impairs immune responses at a higher degree in females. A role of male and female sex hormones in these sex-specific effects is also discussed.

Autophagy is an essential mechanism to maintain cellular homeostasis. Besides its role in controlling the quality of cytoplasmic components, it participates in nutrient obtaining and lipid mobilization under stressful conditions. Furthermore, autophagy is involved in the regulation of systemic metabolic, a function mainly performed by neuronal populations of the arcuate nucleus of the hypothalamus. Several studies have shown that blockade of autophagy in these neurons can affect central regulation of metabolism and impact body energy balance. Moreover, hypothalamic autophagy can be altered during obesity. However, neurons are not the only cell type involved in the central regulation of metabolism. Astrocytes, essential cells for brain homeostasis, are key metabolic regulators. They can sense metabolic signals in the hypothalamus and modulate systemic functions as glucose homeostasis and feeding response. Moreover, the response of astrocytes to obesity has been widely studied. Astrocytes are important mediators of brain inflammation and can be affected by increased levels of saturated fatty acids associated to obesity. Although autophagy plays important roles for astrocyte homeostasis and functioning, the contribution of astrocyte autophagy to systemic metabolism has not been analysed. Furthermore, how obesity can impact astrocyte autophagy is poorly understood. More studies are needed in other to understand the contribution of astrocyte autophagy to metabolism.

By virtue of the knowledge of the beneficial effect of the warm and dry storage, for the growth of the chincuya seed embryo, defined as morphological dormancy. The effect of the same type of storage was studied for the seed viability and germination by soaking gibberellic acid. Also, fatty acids and their kinetics were identified during the warm and dry storage. The following treatments were evaluated: storage time (0, 3, 6, 9 and 12 months), seed soaking in gibberellic acid at 350 mg L-1, and for the control, imbibition in distilled water, both for 72 h. The seed viability was evaluated through the stain test with tetrazolium chloride. The embedded seeds were germinated on absorbent paper towels and incubated at different temperatures of 30 ° C during the day and 25 ° C at night and 12 hours of photoperiod. The lipid profile was developed by gas chromatography. Seeds were held at constant temperature of 25 ± 3 ° C, in darkness, during the storage time. Results demon-strated that the high initial viability was maintained until the ninth month, when it decreases and is statisti-cally different from the other treatments. The smaller germination percentage (26.1 %) was observed in the freshly harvested seeds and, the higher one corresponded to the six months (65.6 %), with these differences being statistically significant. Regarding the identified fatty acids and their average content, it was found that 33.41 % corresponded to palmitic acid, 7.72 % to stearic acid; the arachidic acid with 1.30 %, making a total of saturated fatty acids of 42.44 %. The detected unsaturated fatty acids were: palmitoleic acid 1.52 %, oleic acid 43.37 % and linoleic acid 7.24 %, in total, 52.15 %. No significative changes were observed in the fatty acids content that are the largest part of the total seed reserves; although the higher concentrations matched with the longest germination (three months), with an average of 92.84 % total fatty acids. Specified regressions indi-cated with statistical robustness that palmitoleic and palmitic acids increased while the oleic acid decreased during the dry storage. The arachidic acid showed a slightly downward trend. Also, the concentrations of fat-ty acids were significatively different between unstored and unincubated seeds (intact) and unstored and in-cubated, but without germinating seeds (dormant), in the latter, the total fatty acids content was significantly lower. Given that the application of gibberellic acid and warm dry storage favored germination, as well as the change in fatty acid content during warm dry storage, added to the results already reported on morphological changes and embryonic growth as an effect of the same type of storage, it is established that Annona purpurea seeds present morphophysiological dormancy, also this is the first identification report of arachidic and pal-mitoleic acids in chincuya seeds and the higher germination percentage reported (65.6 %).

Alginate-gelatin hydrogels are extensively used in bioengineering. However, despite different formulations being utilized for growing different cell types in vitro, their pH and its effect, together with the crosslinking ions, of those formulations are still infrequently assessed. In this work we studied how these elements can affect hydrogel stability and printability and influence U2OS and NIH/3T3 cell viability and metabolism on the resulting 3D prints. In this context, 6% alginate + 2% gelatin hydrogels were prepared with 0.1 M MES buffer with pH 5.5, 6.5, 7.0 or 8.0, printed by extrusion-based 3D printing, and crosslinked immediately after printing with either CaCl2 or BaCl2. Our results showed that both the buffer pH and the crosslinking ion (Ca2+ or Ba2+) influence the swelling and degradation rates of the prints. Moreover, the buffer pH influenced the printability of the hydrogel in air, but when printed directly in a fluid-phase CaCl2 or BaCl2 crosslinking bath. In addition, both U2OS and NIH/3T3 cells showed greater cell metabolic activity on one-layer prints crosslinked with Ca2+. Besides, Ba2+ increased cell death of NIH/3T3 cells while had no effect on the U2OS cell viability. The pH of the buffer also caused an important impact on the cell behaviour. U2OS cells showed a 2.25-fold cell metabolism increase on one-layer prints prepared at pH 8.0 in comparison to those prepared at pH 5.5. Whereas, NIH/3T3 cells showed greater metabolism on one-layer prints with pH 7.0. Finally, we observed a difference on cell arrangement of the U2OS cells growing on prints prepared from hydrogels with acidic buffer in comparison to cells growing on those prepared using neutral or basic buffer. These results show that both pH and crosslinking ion influence hydrogel strength and cell behaviour.

The addition of flaxseed and amaranth on the physicochemical, functional and microstructural changes of instant-extruded cereals was evaluated. Six different mixtures were made with additions of amaranth (30%–50%) and flaxseed (10% and 15%) using maize grits and minor additives as supplementary ingredients and then extruded in a twin-screw extruder. The extrudates evaluated, had insoluble and soluble fiber contents increased with the proportion of amaranth and flaxseed. The mixture 4 (higher flaxseed content) presented highest soluble fiber percentage (1.9%). Extruded cereals had the lowest viscosity (<99.5 cp) and highest hardness values (5.2 N) whereas the dietary fiber content was highest. Fiber content increase, resulted in a higher water solubility index (WSI) (0.5) and decrease the water absorption index (WAI) (2.5). Amaranth and flaxseed incorporation increased crystallinity, resulting in a larger, and more compact laminar structure. Amaranth and flaxseed addition resulted in extruded cereals with acceptable physicochemical and functional properties.

Hip fractures are the most frequently treated fractures in the world. Of these, intertrochanteric fractures (ITFs) account for almost 50%. After surgical fixation of ITFs, nonunion is rare. Nonunions are commonly produced from mal-reduction (in varus) and/or inadequate stability of the bone-implant construct and/or fatigue failure of the implants. Other causes of nonunion include posteromedial comminution and osteoporosis. The published incidence of ITF nonunion is 1%-2%. Mechanical complications of ITFs include cut-out, excessive shortening of the proximal femur, delayed union, nonunion, early implant fracture, nail toggle and cut through/medial migration. That is why a fundamental goal in the treatment of ITFs is to achieve stable fixation in osteoporotic bone, allowing early weight bearing. Intraoperative determination of fracture stability is essential. The American Academy of Orthopedic Surgeons (AAOS) clinical practice guidelines for the management of intertrochanteric fractures (ITF) in patients older than 55 years are the following: 1) In patients with stable ITF, the use of either a sliding hip screw (SHS) or a cephalomedullary nail (CMN) is advised (strong strength of evidence). 2) In patients with reverse obliquity fractures, a CMN is recommended (strong strength of evidence). 3) Patients with unstable ITF should be treated with a CMN (strong strength of evidence). 4) In patients with ITF, a short or long CMN may be considered (limited strength of evidence).

The manuscript delves into the intricacies of food production chains, offering a comprehensive breakdown of their components. Moreover, it sheds light on the initiatives orchestrated by government agencies to endorse sustainable practices and fortify areas of opportunity for producer organizations. While the context paints a broad picture, we contend that, to the best of our knowledge, there exists no comparable publication that succinctly encapsulates the role of government in bolstering food production chains. The document unfolds with a detailed exploration of the interaction mechanisms among the various components of the chain. Subsequently, it introduces a set of twelve elements meticulously outlining the multifaceted role of the government. Each element undergoes thorough scrutiny, fostering a nuanced understanding of the intricate relationship between the food production chain and the government's pivotal role in enhancing stability and efficiency. In conclusion, the manuscript not only lays bare the structural elements of food production chains but also presents a unique and in-depth analysis of the government's role, encapsulated within the framework of twelve essential elements.

The health emergency caused by Covid 19 highlighted the food dependency of many cities in the world and Cali and the cities of Valle del Cauca were no exception as they depended on food flows from other regions and countries, so these Entities are part of the corporate food system, to which their rulers delegated food security for their inhabitants. In the same territory and for the last nine years, a second-level organization has been consolidating that brings together 14 peasant agroecological markets and that despite strict confinement measures was able to continue supplying food to consumers in the municipalities of influence that have supported this initiative. The foregoing leads to think that said organization can become a platform for an agroecological food system of regional scope, for which the characteristics that said system should have according to a model based on the principles of agroecology were evaluated.

In contrast to animals, adult organs in plants are not determined during embryogenesis but gen-erated from meristematic cells as plants advance through development. Plant development in-volves a succession of different phenotypic stages and the transition between these stages is termed phase transition. Phase transitions need to be tightly regulated and coordinated to ensure they occur under optimal seasonal, environmental conditions. Polycarpic perennials transition through vegetative stages and the mature, reproductive stage many times during their lifecycles and, in both perennial and annual species, environmental factors and culturing methods can re-verse the otherwise unidirectional vector of plant development. Epigenetic factors regulating gene expression in response to internal cues and external (environmental) stimuli influencing the plant’s phenotype and development have been shown to control phase transitions. How develop-mental and environmental cues interact to epigenetically alter gene expression and influence these transitions are not well understood and understanding this interaction is important considering the current climate change scenarios, since epigenetic maladaptation could have catastrophic con-sequences for perennial plants in natural and agricultural ecosystems. Here we review studies focussing on the epigenetic regulators of the vegetative phase change and highlight how these mechanisms might act in exogenously induced plant rejuvenation and regrowth following stress.

Injury to the central nervous system (CNS), in most vertebrate animals, results in permanent damage and lack of function, due to their limited regenerative capacities. In contrast, echinoderms can fully regenerate their radial nerve cord (RNC) following transection, with little or no scarring. Investigators have associated the regenerative capacity of some organisms with the stress response and inflammation produced by the injury. Here we explore the gene activation profile of the stressed holothurian CNS. To do this, we performed RNA sequencing on isolated RNC explants submitted to the stress of transection and enzyme dissection and compared them to explants kept in culture for 3 days following dissection. We describe stress-associated genes, including members of heat-shock families, ubiquitin-related pathways, transposons, and apoptosis that were differentially expressed. Surprisingly, the stress response does not induce apoptosis in this system. Other genes associated with stress in other animal models, such as hero proteins and those associated with the integrated stress response, were not found to be differentially expressed either. Our results provide a new viewpoint on the stress response in the nervous system of an organism with an amazing regenerative capacity. This is the first step to deciphering the molecular processes that allow echinoderms to undergo fully functional CNS regeneration while also providing a comparative view for students of the stress response in other organisms.

Metabolic syndrome is a growing global health problem. Evidence suggests that diets rich in phytochemical-containing herbs and spices can contribute to reduced risk of chronic disease. This review assesses the scope of evidence supporting the use of herbs and spices in the diet for prevention or treatment of metabolic syndrome and associated health conditions. A search of PubMed and Scopus databases was carried out to assess the available clinical or cohort evidence for culinary doses of commonly used herbs and spices. Trials that were measuring health factors related to metabolic disorders or the health of individuals with metabolic syndrome or associated diseases were included. Out of a total of 1742 papers identified, there were 146 relevant studies on black pepper, chilli, cardamom, cinnamon, coriander, cumin, fennel, fenugreek, garlic, ginger, Nigella seed, rosemary, sage and turmeric. No relevant research was found for cloves, mint, oregano, parsley or thyme. Cinnamon, fenugreek and ginger were the herbs/spices with the most published trials on them and showed promise for glycaemic control. Cardamom appears to have potential to reduce inflammatory markers, and cinnamon, ginger and turmeric for blood lipids. Patients with type 2 diabetes were the population most likely to be included in studies, but the preventative benefits of herbs/spices in healthy populations were also investigated, particularly for chilli, ginger and cinnamon. There is evidence for the beneficial effect of culinary doses of many common herbs/spices in the prevention and treatment of metabolic syndrome and associated disorders.

The aim was to examine the sociodemographic predictors associated with changes in movement behaviours (physical activity, screen time and sleep) among toddlers and pre-schoolers during the early stages of the coronavirus disease 2019 pandemic in Chile. Caregivers of 1- to 5-year-old children completed an online survey between March 30th and April 27th, 2020. Information about the child's movement behaviours before (retrospectively) and during the pandemic, as well as family characteristics were reported. In total, 3,157 participants provided complete data (mean children age: 3.1±1.38 years). During early stages of the pandemic, time spent in physical activity decreased, recreational screen time and sleep duration increased, and sleep quality declined. Toddlers and pre-schoolers with space to play at home and living in rural areas experienced an attenuated impact of the pandemic restrictions on their physical activity levels, screen time, and sleep quality. Older children, those whose caregivers had a higher educational level, and children living in apartments had greater changes, mainly a decrease in total physical activity and increase in screen time. This study has shown the significant impact of the pandemic restrictions on movement behaviours in toddlers and pre-schoolers in Chile.

In this article, we have tried to answer the questions of how an entire city's fiction was created for the development of Japanese American internment camps and in which way contributions of sustainable crafts and even art could have interceded. To this aim, we have searched the literature and reviewed archives, primarily from the American West Coast. We have found that beyond adaptation to the circumstances, the visual representation of the city's settlement, founding, and daily activities, instead of typical panoptic or somber prisons’ imagery, are depicted in the selected images and that their use precisely fostered its sustainability. This leads us to deduce that a "city fiction" was necessary for such survival and endurance and that its artistic representation was primarily involved in the state's ideological apparatus. On the other hand, fissures subtly seethed the violence exerted in the camps by stealth and in a hidden fashion. We have concluded that artistic activity justified the city's fiction, together with other examples, highlighting the conditions of systemic violence and oppression for the inmates. In this framework, the artworks generated constitute a historical document of sustainability.

TThe XPRIZE Foundation designs and operates multi-million-dollar, global competitions to incentivize the development of technological breakthroughs that accelerate humanity toward a better future. To combat the COVID-19 pandemic, the Foundation coordinated with several organizations to make available data sets about different facets of the disease and to provide the computational resources needed to analyze those data sets. This is paper is a case study of the requirements, design, and implementation of the XPRIZE Data Collaborative, a cloud-based infrastructure that enables the XPRIZE to meet its COVID-19 mission and host future data-centric competitions. We examine how a Cloud Native Application can use an unexpected variety of Cloud technologies, ranging from containers, serverless computing, to even older ones like Virtual Machines. We also search and document the effects that the pandemic had on application development in the Cloud. We include our experiences of having users successfully exercise the Data Collaborative, detailing the challenges encountered and areas for improvement and future work.

Photobiomodulation (PBM) is a procedure that uses light to modulate cellular functions and bio-logical processes. Over the past decades, PBM has gained considerable attention for its potential in various medical applications due to its non-invasive nature and minimal side effects. This narrative review article examines the existing literature on PBM, encompassing research studies, clinical trials, and technological developments. This review highlights the mechanisms of action underlying PBM, including the interaction with cellular chromophores and the activation of in-tracellular signaling pathways. The evidence from clinical trials and experimental studies to evaluate the efficacy of PBM in clinical practice is summarized with a special emphasis on der-matology. Furthermore, advancements in PBM technology, such as novel light sources and treat-ment protocols, are discussed in the context of optimizing therapeutic outcomes and improving patient care. This narrative review underscores the promising role of PBM as a non-invasive therapeutic approach with broad clinical applicability. Despite the need for further research to develop standard protocols, PBM holds great potential for addressing a wide range of medical conditions and enhancing patient outcomes in modern healthcare practice.

The first diastereoselective synthesis of (–)-1-epi-lentiginosine stars from a common chiral trans-epoxyamide derived from 2-pyridincarbaldehyde is reported. This methodology involves a sequential oxirane ring opening and intramolecular 5-exo-tet cyclization of tosylate tras-epoxyalcohol to afford a diastereomeric mixture of indolizinium salts in a one-pot fashion, followed by regio- and diastereospecific pyridinium ring reduction.

In studies of dynamic stability and power quality, it is necessary to know the mechanical parameters that determine the transient response of a wind turbine. The exact value of these parameters is not as decisive as the power curve can be, but an estimate that is far from reality can distort or even invalidate the simulation results. Despite its importance, this information, especially the inertia, but also the stiffness and damping constant of the drive-train, is hardly available for the turbine model under investigation. In this work, the different bibliographical sources that provide values of blade inertia in kg·m2 will be reviewed, and above all, those that provide a distribution of masses along the span of the blade. With this, different reliable relations will be obtained that allow calculating the inertia of the turbine rotor, based on the mass and length of the blade. When the center of gravity is also available, a very correlated expression is provided to obtain the inertia. The even rarer references to the stiffness and damping constant of the drive-train will also be reviewed.

Carbon (C) is one of the most abundant elements. It is part of all living organisms and is found in all states of matter (solid, liquid, gas, and plasma). It can take the form of one of the hardest and transparent materials (diamond) or it can be flexible and dark ( graphite), with many carbonaceous materials at both extremes. In gaseous form, C is a component of several greenhouse gas emitted during the combustion of fossil fuels. Carbon movement between the atmosphere, land (biosphere and lithosphere), and ocean (hydrosphere) can alter total amounts in each pool. Human activities accelerate C movement into the atmosphere, causing increases in climate change. This shift from terrestrial and oceanic C pools to the atmosphere cause an increase in the intensity and duration of droughts, hurricanes, snowstorms, and other natural phenomenon. Although society hears about C emissions there is a lack of understanding of its importance and the need to decrease C in the atmospheric pool to avoid exacerbating climate change. Forests and biochar are two biological methods to retain C in the terrestrial pool for long time and at very low cost. This review details where C comes from, its relationship with forests, and biochar and their roles in increasing carbon sequestration to limit the impacts of climate change and continue having future sustainable forests and ecosystems services that we enjoy today.

Background: Trigeminal neuralgia associated to vascular compression, by aberrant or ectopic arterial or venous vessels, is a frequent condition in clinical practice. Management with microvascular decompression through a Minimal invasive retrosigmoidal has shown high rates of pain control, with low complication rates and excellent therapeutic results. Objective: To describe the surgical technique and clinical outcomes in terms of pain relief after microvascular decompression for trigeminal nerve, through a minimal invasive retrosigmoidal parasterional burr-hole technique. Methods: A group of patients with trigeminal neuralgia refractory to medical management who underwent microvascular decompression considering outcomes based on Visual Analogue Scale (VAS), and Barrow Neurological Institute Pain Scale (BNIPS). Added to a technical note of the surgical technique for a minimal invasive retrosigmoidal parasterional burr-hole. Results: Twenty-two patients were evaluated, clinical assessment after surgical intervention showed a decrease pain according to VAS, resulting from an average preoperative state of 9.5 ± 0.37 to a postoperative condition of 1.32 ± 1.28, exhibiting statistically significant changes (p < 0.0001, d = 9.356). On the other hand, in relation to the BNIPS scale, a decrease from an average preoperative status of 4.55 ± 0.25, to a postoperative status at 12 months of 1.73 ± 0.54 was also demonstrated, showing significant changes (p < 0.0001, d = 3.960). Conclusion: Microvascular decompression of the trigeminal nerve through a minimal invasive retrosigmoidal parasterional burr-hole is feasible and can be a safe and effective technique for the management of pain.

Plant extracts have been evaluated to determine their bioactivities and their potential use in wound healing. In this study, a conductive composite material, based on graphene oxide (GO), nanocellulose (CNF) and tannins (TA) from pine bark, reduced using polydopamine (PDA), was developed for wound dressing. The amount of CNF and TA was varied in the composite material and a complete characterization including SEM, FTIR, XRD, XPS, TGA was performed. Also, the conductivity, mechanical properties, cytotoxicity, and in vitro wound healing of the materials were evaluated. The results showed a successful physical interaction between CNF, TA and GO. In-creasing the CNF amount in the composite reduced the thermal properties, surface charge and conductivity of the material, but its strength, cytotoxicity and wound healing performance were improved. The TA incorporation slightly reduced the cell viability and migration, which may be associated with the doses used and the chemical composition of the extracts. However, the in vitro obtained results demonstrated that these composite materials can be suitable for wound healing.

Although genome-wide association studies (GWAS) have identified several hundred loci associated with autoimmune diseases, their mechanistic insights are still poorly understood. The human genome is more complex than common single nucleotide polymorphisms (SNPs) that are interrogated by GWAS arrays. Some structural variants such as insertions-deletions, copy number variations, and minisatellites that are not very well tagged by SNPs cannot be fully explored by GWAS. Therefore, it is possible that some of these loci may have large effects on autoimmune disease risk. In addition, other layers of regulations such as gene-gene interactions, epigenetic-determinants, gene and environmental interactions also contribute to the heritability of autoimmune diseases. This review focuses on discussing why studying these elements may allow us to gain a more comprehensive understanding of the aetiology of complex autoimmune traits.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

In this paper, the active front-end (AFE) converter topology for the total harmonic distortion (THD) reduction in a wind energy system (WES) is used. A higher THD results in serious pulsations in the wind turbine (WT) output power and in several power losses at the WES. The AFE converter topology improves capability, efficiency and reliability in the energy conversion devices; by modifying a conventional back-to-back converter, from using a single voltage source converter (VSC) to use pVSC connected in parallel the AFE converter is generated. The THD reduction is done by applying a different phase shift angle at the carrier of digital sinusoidal pulse width modulation (DSPWM) switching signals of each VSC. To verify the functionality of the proposed methodology, the WES simulation in Matlab-Simulink® is analyzed, and the experimental laboratory tests using the concept of rapid control prototyping and the real-time simulator Opal-RT® Technologies is achieved. The obtained results show a type-4 WT with total output power of 6MVA, generating a THD reduction up to 5.5 times at the WES.

Over the last 20 years, begomoviruses have emerged as devastating pathogens, limiting the production of different crops worldwide. Weather conditions increase vector populations, with negative effects on crop production. In this work we evaluated the relationship between the in-cidence of begomovirus and climatic conditions before and during the crop cycle. Soybean and bean fields from the northwest (NW) of Argentina were monitored for 14 years and classified as moderate (≤50%) and severe (> 50%) according to the relative incidence. Two hundred bio-meteorological variables were constructed, summarizing meteorological data in 10-day peri-ods from June to March of each crop year. The studied variables included temperature, precipi-tation, relative humidity, wind (speed and direction), pressure, cloudiness and visibility. For bean, high maximum winter temperatures, low spring humidity and precipitation 10 days before planting correlated with severe incidence. In soybeans, high late winter and pre-planting tem-peratures, and low spring precipitations were found to be good predictors of high incidence of begomovirus presence. The results suggest that temperature and pre-sowing precipitations can be used to predict incidence status [predictive accuracy: 82% (bean) and 75% (soybean)]. Thus, these variables can be incorporated in early warning systems for crop management deci-sion-making to reduce the virus impact on bean and soybean crops.

The effect of individual and combined supplementation of FA and GPM on physiological variables, productive performance, and carcass characteristics of finishing pigs under heat stress conditions were investigated. Forty Yorkshire x Duroc pigs (80.23 kg) were individually housed and randomly distributed into 4 groups under a 2 x 2 factorial arrangement (n=10): Control (basal diet, BD); FA, BD + 25 mg FA; GPM, BD with 2.5% GPM; and MIX, BD with 25 mg FA and 2.5% GPM. Additives were supplemented for 31 days. The inclusion of FA or GPM did not modify rectal temperature and respiratory rate. An interaction effect (P &lt;0.05) was observed on FI, while average daily gain (ADG) and feed conversion (FC) were not affected by treatments (P &gt;0.05). The inclusion of FA improved hot and cold carcass weight and carcass yields, while the addition of GPM decreased the marbling (P &lt;0.05), and GPM tended to increase loin area (P &lt;0.10). GPM increased liver weight (p &lt;0.05). The addition of GPM and FA can improve some carcass characteristics under heat stress conditions. It is necessary to continue investigating different levels of inclusion of GPM and FA, to demonstrate their potential growth promoting effect in finishing pigs.

Ulcerative colitis (UC) is a chronic autoimmune disorder affecting the colonic mucosa. UC is a subtype of inflammatory bowel disease along with Crohn’s disease and presents with varying extraintestinal manifestations. No single etiology for UC has been found, but a combination of genetic and environmental factors is suspected. Research has focused on the role of intestinal dysbiosis in the pathogenesis of UC, including the effects of dysbiosis on the integrity of the colonic mucosal barrier, priming and regulation of the host immune system, chronic inflammation, and progression to tumorigenesis. Characterization of key microbial taxa and their implications in the pathogenesis of UC and colitis-associated cancer (CAC) may present opportunities for modulating intestinal inflammation through microbial-targeted therapies. In this review, we will discuss the microbiota-immune crosstalk in UC and CAC, as well as the evolution of microbiota-based therapies.

In this work a research on pulsed electrochemical micromachining of Stainless Steel is presented. A suitable equipment to study the process is described as well as a fitting procedure to machine and measure the variables involved. A tool of Tungsten with a tip of about 5 mm diameter sunk in an electrolyte of NaNO₃ is used for the process. The pulse on-time must be maintained in the order of ns to achieve a good current confinement, since the tool is active. Some experiments were made to assess the most important variables of the process, as current confinement, surface roughness, material removal rate and efficiency. It is observed that the current confinement get worse when the pulse on-time increases, as well as surface roughness. The material removal rate and the efficiency increase with the voltage amplitude and the pulse on-time. The voltage amplitude must be higher than 12 V so that the phenomenon of passivation disappears. There is a compromise in the choice of the variables, so a suitable combination of parameters is determined so that a good material removal rate with an acceptable result is achieved.

A critical discussion on the computation of the dispersion diagram in periodic one-dimensional guiding structures is carried out. In particular, an analysis is presented of the pros and cons of combined methods that make use of full-wave simulations done with commercial software packages with further analytical post-processing based on simplifications brought by an equivalent circuit model of the structure. Some of the most common methods reported in the literature are reviewed and their advantanges and limitations highlighted. Our discussion is complemented with several selected numerical examples in order to discuss the most relevant aspects that a potential user of these methods should be aware of. Special attention is paid to the relevant role played by the high-order coupling between the two halves of a symmetric unit cell of the periodic structure.

It has been known that the performance of the High-Pressure Grinding Rolls (HPGR) varies as a function of method used to confine laterally the rolls, their diameter/length (aspect) ratio as well as their condition, if new or worn. However, quantifying these effects through direct experimentation in machines with reasonably large dimensions is not straightforward given the challenge, among others, of guaranteeing that the feed material remains unchanged. The present work couples the discrete element method (DEM) to multibody dynamics (MBD) and a novel particle replacement model (PRM) to simulate the performance of pilot-scale HPGRs grinding pellet feed. It shows that rotating side plates, in particular when fitted with studs, allow reaching more uniform forces along the bed, which also translates in a more constant product size along the rolls as well as higher throughput. It also shows that the edge effect is relatively constant with roll length, leading to substantially larger proportional edge regions for high-aspect ratio rolls. On the other hand, the product from the center region of such rolls was found to be finer when pressed at identical specific forces. Finally, rolls were found to have higher throughput, but generate a coarser product when worn following the commonly observed trapezoidal profile. The approach used in industry to compensate for roller wear by increasing the specific force and roll speed has then been demonstrated to be effective to maintain and potentially even increase product fineness and throughput, as long as the minimum safety gap is not reached.

The calculation of the global shear capacity of steel-concrete composite downstand cellular beams with precast hollow-core units is important as it affects the span to depth ratios and the amount of material used, hence affects the embodied CO2 calculation when designers are deciding on the floor grids. This paper presents a reliable tool that can be used by designers to alter and optimise grip options during the preliminary design stages, without the need to run onerous calculations. The global shear capacity prediction formula is developed using five machine learning models. First, a finite element model database is developed. The influence of the opening diameter, web opening spacing, tee-section height, concrete topping thickness, the interaction degree, and the number of shear studs above the web opening are investigated. Reliability analysis is conducted to assess the design method and propose new partial safety factors. The Catboost Regressor algorithm presented better accuracy compared to the other algorithms. An equation to predict the shear capacity of composite cellular beams with hollow-core units is proposed by Gene Expression Programming. In general, the partial safety factor for resistance, according to the reliability analysis, varied between 1.25 and 1.26.

To determine the ethical-attitudinal profile of university students in the education career during the pandemic with a tendency towards a new normality. University students of the education career were surveyed online, in an ethical key (axiological attitude, moral attitude and attitude towards new normality). The research was descriptive of univariate hypothesis, with non-probabilistic snowball sampling, reaching a sample of 480 participants. The Ethical-Attitudinal Profile Scale (EPEA) was designed, whose reliability was 0.93 in Lawshe's formula and 0.89 in Cronbach's Alpha. In the axiological attitude, values were obtained more frequently: respect with 79%, sincerity with 73%, prudence with 72%. In the moral attitude, a polar result is contrasted between laxity (67%) and kindness (45%); while, in the attitude towards new normality, there was no spike in frequencies, being distributed more homogeneously between indicators, with a low resilience index. There is an adequate evaluative profile of the university students of the education career despite the context of the pandemic and the trend towards a new normality; having a moral attitude of laxity inferred by the circumstances of uncertainty that are experienced in adverse contexts.

Companies have been increasing the amount of data that they collect from their systems and processes, considering the decrease in the cost of memory and storage technologies in recent years. The emergence of technologies such as Big Data, Cloud Computing, E-Science, and the growing complexity of information systems made evident that traceability and provenance are promising approaches. Provenance has been successfully used in complex domains, like health sciences, chemical industries, and scientific computing, considering that these areas require a comprehensive semantic traceability mechanism. Based on these, we investigate the use of provenance in the context of Software Process (SP) and introduce a novel approach based on provenance concepts to model and represent SP data. It addresses SP provenance data capturing, storing, new information inferencing and visualization. The main contribution of our approach is PROV-SwProcess, a provenance model to deal with the specificities of SP and its ability in supporting process managers to deal with vast amounts of execution data during the process analysis and data-driven decision-making. A set of analysis possibilities were derived from this model, using SP goals and questions. A case study was conducted in collaboration with a software development company to instantiate the PROV-SwProcess model (using the proposed approach) with real-word process data. This study showed that 87.5% of the analysis possibilities using real data was correct and can assist in decision-making, while 62.5% of them are not possible to be performed by the process manager using his currently dashboard or process management tool.

This work presents a new algorithm to resolve the problem of distribution network reconfiguration using the Tabu Search metaheuristic and voltage drop. The proposed method presents a different way to obtain the initial solution using the voltage drop, as well as a new way to generate a neighborhood of candidate solutions, based on randomness and the voltage drop, to perform a smooth and steady descent execution of the algorithm. The proposed algorithm has the main objective to reduce the active power losses in distribution networks, but it also achieves an refinement in the voltage profile. The proposed method was tested in two distribution systems, the 33-Bus and 94-Bus systems, commonly found and tested in the literature. The results of the tests show that the proposed method presents a low computational cost, achieves good solutions, and is better than the other methods found in the literature.