The study concentrates on researching possibilities of using computer image analysis and neural modeling in order to assess selected quality discriminants of spray-dried chokeberry powder. The aim of the paper is quality identification of chokeberry powders on account of their highest dying power, the highest bioactivity as well as technologically satisfying looseness of powder. The article presents neural models with vision technique backed up by devices such as digital camera as well as electron microscope. Reduction in size of input variables with PCA has influence on improving the processes of learning data sets, thus increasing effectiveness of identifying chokeberry fruit powders included in digital pictures, which is shown in the results of the conducted research. The effectiveness of image recognition are presented by classifying abilities as well as low Root Mean Square Error (RMSE), for which the best results are achieved with typology of network type Multi-Layer Perceptron (MLP). The selected networks type MLP are characterized by the highest degree of classification at 0.99 and RMSE at 0.11 at most at the same time.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

The article presents tests aimed to verify the possibility of making T-joints in TMCP steel using laser. The tests involved the use of 10 mm thick high yield point steel S700MC obtained in an industrial manufacturing process. The joints made in the tests were single and double-sided. Subsequent non-destructive tests revealed that the joints obtained in the tests represented quality level B in accordance with PN-EN ISO 13919-1. Single-sided welding performed using the laser beam having a power of 11 kW enabled the obtainment of 8 mm deep penetration without visibly deforming the web of the joint. The double-sided welded joints were characterised by proper geometry and the presence of gas pores in the welds not compromising the requirements of quality level B (strict requirements). The weld structure was bainitic-ferritic. The weld hardness was by approximately 60 HV1 higher than that of the base material (280 HV1). The HAZ area was slightly softer than the base material. The tests of thin foils performed using a high-resolution scanning transmission electron microscope revealed that, during welding, an increase in the content of the base material in the weld was accompanied by an increase in contents of alloying microagents Ti and Nb, particularly near the fusion line. The above-named alloying microagents, in the form of fine-dispersive (Ti,Nb)(C,N) type precipitates, could reduce plastic properties of joints.

The article’s goal is to overview challenges and problems on the way from the state of the art CUDA accelerated neural networks code to multi-GPU code. For this purpose, the authors describe the journey of porting the existing in the GitHub, fully-featured CUDA accelerated Darknet engine to OpenCL. The article presents lessons learned and the techniques that were put in place to make this port happen. There are few other implementations on the GitHub that leverage the OpenCL standard, and a few have tried to port Darknet as well. Darknet is a well known convolutional neural network (CNN) framework. The authors of this article investigated all aspects of the porting and achieved the fully-featured Darknet engine on OpenCL. The effort was focused not only on the classification with the use of YOLO1, YOLO2, and YOLO3 CNN models. They also covered other aspects, such as training neural networks, and benchmarks to look for the weak points in the implementation. The GPU computing code substantially improves Darknet computing time compared to the standard CPU version by using underused hardware in existing systems. If the system is OpenCL-based, then it is practically hardware independent. In this article, the authors report comparisons of the computation and training performance compared to the existing CUDA-based Darknet engine in the various computers, including single board computers, and, different CNN use-cases. The authors found that the OpenCL version could perform as fast as the CUDA version in the compute aspect, but it is slower in memory transfer between RAM (CPU memory) and VRAM (GPU memory). It depends on the quality of OpenCL implementation only. Moreover, loosening hardware requirements by the OpenCL Darknet can boost applications of DNN, especially in the energy-sensitive applications of Artificial Intelligence (AI) and Machine Learning (ML).

The aim of the study was to assess the relationship between the shape of the anterior-posterior curvature of the spine and body composition in school-children. The study included 257 children, aged 11-12. Correct spinal curvature was established in 106 (41.08%) subjects. Other types included: decreased kyphosis and correct lordosis - 40 participants (15.50%), correct kyphosis and decreased lordosis - 24 individuals (9.30%), increased kyphosis and correct lordosis - 17 subjects (6.59%), correct kyphosis and increased lordosis - 22 children (8.53%), decreased kyphosis and decreased lordosis - 32 people (12.40%), decreased kyphosis and increased lordosis - 4 of the examined subjects (1.55%), increased kyphosis and lordosis - 13 people (5.04%). In addition, 134 (51.94%) demonstrated scoliotic posture and 8 (3.10%) scoliosis. There were significant relationships between the shape of the anterior-posterior curvatures and body composition in school-children. Those with a strong body build (predominance of mesomorphs) were generally characterised by the correct formation of these curvatures. In contrast, lean people (with the predominance of ectomorphic factors) were more likely to experience abnormalities. No correlations with body composition were observed in the group with scoliotic posture or scoliosis.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

Cryptosporidiosis is a widespread disease caused by the parasitic protozoan Cryptosporidium spp., which infects various vertebrate species, including humans. Once unknown as a gastroenteritis-causing agent, Cryptosporidium spp. is now recognized as a pathogen causing life-threatening disease, especially in immunocompromised individuals such as AIDS patients. Advances in diagnostic methods and increased awareness have led to a significant shift in the perception of Cryptosporidium spp. as a pathogen. Nowadays, genomic and proteomic studies have played a main role in understanding the molecular biology of this complex-life-cycle parasite. Genomics has enabled the identification of numerous genes involved in the parasite's development and interaction with hosts. Proteomics has allowed for the identification of protein interactions, their function, structure, and cellular activity. The combination of these two approaches has significantly contributed to the development of new diagnostic tools, vaccines, and drugs for cryptosporidiosis. In this review, we summarize the major accomplishments in the field of Cryptosporidium research using genomics and proteomics.

Background and objectives: Patients with multiple sclerosis (MS) have many potential factors (spasticity, immobilization, glucocorticoids use) which can deteriorate the anthropometrical status and body composition and may have the potential impact on the functional mobility and basic motor skills improvement after physiotherapy. The aim of the study was to assess the functional mobility and basic motor skills in patients with MS and to correlate them with disability and anthropometrical status and body composition parameters. Materials and Methods: Timed Up-and-Go test (TUG), and six-minute walk test (6MWT) were performed in 36 patients with MS before and after 4 weeks of physiotherapy. Body mass index (BMI), waist to height ratio (W/HtR), and waist-to-hip ratio (WHR) were assessed in this group. Body composition was evaluated by bioelectrical impedance analysis (BIA) and fat mass (FAT), fat free mass (FFM), total body water (TBW) and predicted muscle mass (PMM) were expressed as percentage of body mass. Clinical status was assessed by EDSS and AI scales. Results: After physiotherapy, there was a significant improvement in functional mobility and basic motor skills assessed by total distance in 6MWT (p<0.001) and in TUG trials (p<0.001). Positive significant correlations were found between the results obtained in both tests (either before and after physiotherapy) vs. FFM, TBW and PMM, whilst worse results in functional mobility and basic motor skills correlated significantly with higher WHtR, WHR and FAT (p<0.05). Clinical status (EDSS) were significantly related to the WHtR and body composition parameters with the same manner as the results in the either 6MWT and TUG. However, there were no significant relationships between BMI vs. either clinical status (EDSS, AI) and functional mobility tests results in patients with MS. Conclusions: Functional mobility and basic motor skills may be significantly improved during the physiotherapy, but they are related to the anthropometrical status and body composition of MS patients. Moreover, disability status is also significantly related to this parameters. Body composition deterioration seems to be the important target for the therapeutic intervention in MS patients. For proper nutritional status assessment in patients with MS, body composition analysis or WHtR instead BMI should to be used.

The association between human and cat (F. catus) is well known. This domestic animal is also known for its malodorous urine and feces. The complexity of the odorous urine and feces impacts human life by triggering the human sensory organ in a negative way. The objective of this research was to identify the volatile organic chemicals (VOCs) and associated odors in cat urine and feces using gas chromatography-mass spectrometry and simultaneous sensory analysis of fresh and aged samples. The solid-phase microextraction (SPME) technique was used to pre-concentrate the VOCs emitted from urine or feces samples. Twenty-one compounds were identified as emitted from fresh urine, whereas 64 compounds were emitted from fresh feces. A contrasting temporal impact was observed on the emission of VOCs for urine and feces. On aging, the emission increased to 36 detected chemicals for stale urine, whereas only 17 chemicals were detected in stale feces. Not all compounds were malodorous; some compounds had a pleasant hedonic smell to the human nose. Although trimethylamine, low molecular weight organic acids, and ketones were contributors to the odor to some extent, phenolic compounds and aromatic heterocyclic organic N compounds generated the most intense odors and substantially contributed to the overall malodor, as observed by this study. This work might be useful to formulate cat urine and feces odor remediation approaches to reduce odor impacts.

Background: The assessment of the incidence and characteristic of acute and chronic post-operative endophthalmitis (POE) after cataract surgery in Poland during 2010 - 2015. Patients and methods: All hospitalizations of patients, in the National Database of Hospitalizations, who underwent cataract surgery alone or in combined procedures in Poland between January 2010 and December 2015, with a billing code of endophthalmitis, were selected. Acute endophthalmitis was identified if symptoms occurred within 1 - 42 days from the cataract surgery and chronic endophthalmitis if symptoms occurred ≥ 43 days after cataract surgery, respectively. Results: In total, 1331 cases of POE after 1,218,777 cataract extractions were identified. The overall incidence of POE decreased from 0.125% in 2010 to 0.066% in 2015. In multiple logistic regression analyses, increasing age was significantly associated with acute POE, while type II diabetes mellitus, extracapsular cataract extraction and one-day surgery were significantly associated with chronic POE. The combined cataract surgery and male sex were significant risk factors for both acute and chronic POE. A total of 62.51% of all eyes affected by POE received antibiotic treatment and 37.49% had vitrectomy treatment. Conclusions: During the study period, the total incidence of post-operative endophthalmitis after cataract surgery decreased significantly.

Urination on carpet and subflooring can develop into persistent and challenging to mitigate odor. Very little or no information is published on how these VOCs change over time when urine is deposited on the carpet covering a plywood-type subflooring. This research has investigated the VOCs emitted from carpet+subflooring (control), carpet+subflooring sprayed with water (control with moisture), and cat urine-contaminated carpet+subflooring (treatment) over time (day 0 and 15). In addition, the effect of popular cleaning products on VOCs emitted and evaluated their efficacy in eliminating those indoor odors over time (day 0 and 15). Carpet-subflooring with all treatments were also contaminated with Micrococcus luteus, nonmotile obligate aerobe commonly found in household dust, to observe the impact of the aerobe on carpet-subflooring VOCs emission. VOCs emitted from carpet+subflooring receiving different treatments were collected from headspace using solid-phase microextraction (SPME). The VOCs were analyzed using a multidimensional gas chromatography-mass spectrometer attached to an olfactometry (GC-MS-O). Many common VOCs were released from the carpet on day one and day fifteen, specifically from urine contamination. Cleaning products were effective in masking several potent odors of cat urine contaminated carpet VOCs on day one but unable to remove the odor appeared on day 15 in most cases.

TRPOMI instrument aboard Sentinel-5P is a relatively new, high-resolution source of information about atmosphere composition. One of the primary atmospheric trace gases that we can observe through it is nitrogen dioxide. By now, we were using the chemical weather model (GEM-AQ) as a mean for estimating nitrogen dioxide concentration on a regional scale. Although well established in atmospheric science, the GEM-AQ simulations were always based on emission data, which in the case of the energy sector were reported by stack owners. In this paper, we attempted to compare the TROPOMI and GEM-AQ derived VCDs over Poland with a particular focus on large point emitters. We also checked how cloudy conditions influence TROPOMI results. Finally, we tried to link the NO2 column number densities with surface concentration using boundary layer height as an additional explanatory variable

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

The article presents a hybrid method for calculating the chemical composition of steel with the required hardness after cooling from the austenitizing temperature. Artificial neural networks and genetic algorithms were used to develop the model. Based on 550 diagrams of continuous cooling transformation (CCT) of structural steels available in the literature, a dataset of experimental data was created. Artificial neural networks were used to develop a hardness model describing the relationship between the chemical composition of the steel, the austenitizing temperature, and the hardness of the steel after cooling. A genetic algorithm was used to identify the chemical composition of the steel with the required hardness. The value of the objective function was calculated using the neural network model. The developed method for identifying the chemical composition was implemented in a computer application. Examples of calculations of mass concentrations of steel elements with the required hardness after cooling from the austenitizing temperature are presented. The model proposed in this study can be a valuable tool to support chemical composition design by reducing the number of experiments and minimizing research costs.

The presented results of simulations take into account the optical parameters of the selected sea region (from literature data on the southern Baltic Sea) and two optically extreme types of crude oil (from historical data) which exist in the form of a highly diluted oil-in-water emulsion (10 ppm). The spectral index was analyzed based on the results of modelling the radiance reflectance distribution for almost an entire hemisphere of the sky (zenith angle from 0 to 80o). The spectral index was selected and is universal for all optically different types of oil (wavelengths 650 and 412 nm). The possibility of detecting pollution in the conditions of the wavy sea surface (as a result of wind of up to 10 m/s) was studied. It has been also shown that if the viewing direction is close to a direction perpendicular to the sea surface, observations aimed at determining the spectral index are less effective than observation under the zenith angle of incidence of sunlight for all azimuths excluding the direction of sunlight specular reflection.

The history of health records (later also called medical records), including ones regarding individual patients, is thousands of years old. It finds it roots in the first ancient civilisations. Up until the 19^th century the records’ purpose was mainly an educational one. In the 19^th and 20^th century they started becoming significant in other roles as well, including those not strictly limited to medicine. In particular, to account for medical procedures, insurance proceeds or legal action. Currently we are living in a revolutionary era when it comes to health records, in which their character has changed from a “paper-based” to an electronic one. This paper presents the development of health records from the ancient to modern times, mainly in Europe and North America. Other cultures and civilisations, including China and India, are not discussed. An analysis of available sources was conducted, inter alia digital versions of manuscripts up to hundreds of years old. The analysis was based on PubMed and Google Scholar (several key words, all the available sources). Sources published in non-international languages (e.g. Dutch) were also investigated. Overall, approximately 600 articles were analysed, 158 of which were used and cited in this paper. The conclusions drawn from the analysis are as follows: (1) Health records, priorly used mostly for educational purposes, for about 100 years now have acquired a fully formal status. (2) We are currently facing the most revolutionary changes regarding the transformation of paper-based records into electronic ones. (3) The consequences of this process include systematic applications of solutions within the area of e-health, which allow us to make medical services more flexible, improve the health of individual patients and entire populations and potentially limit expenditure. (4) In the light of the ongoing COVID-19 pandemic, introducing electronic health records could be beneficial in terms of limiting the potential sources of contamination (physical copies of health records), saving time and resources, and improving the network of communication between medical centres.

This work addresses the problem of the application of artificial intelligence to the creation and maintenance of medical documentation and the use of big data in medicine to support efficient patient diagnosis and treatment. This study covers the latest advances in AI and big data, based on literature reviews and interviews with leading experts in these fields. The following conclusions were obtained: (1) Based on the needs of patients and providers of medical services, and given the latest technological advances, all medical documentation should be digital and the processes of its creation, access, sharing, and consistency checking should by supported by suitably designed AI systems. (2) The knowledge contained in medical documentation constitutes a resource of strategic importance for humanity, with almost unlimited potential. (3) All medical documentation should be anonymised and should be made widely available, just like data and research results in the field of experimental physics. (4) This will accelerate development of new treatments, best practice and help to identify new medical emergencies, such as Covid-19. In practice today, unfortunately, the design of medical record systems is fragmented between institutions and countries, often focusing discussions on narrow technical details, and forcing clinicians to waste time on filling up multiple pages of illness history. This leads to many inefficiencies and lost opportunities and necessitates a fundamentally new approach.

Polypropylene (PP) is commonly used in the polymer processing industry. Its feature is a good chemical resistance, it is non-toxic and not harmful to people. Polypropylene is widely used in the manufacturing of food packages, laboratory and medical equipment, electric cables insulators, automotive parts, toys and furniture. The application of this material enables us to obtain complicated shapes of big surfaces. It is also highly recyclable. Polylactide (PLA) is a product of the so called “green chemistry” because it is obtained from the renewable raw materials (biomass). As its price is higher compared to the traditional polymers, its repeated use (recycling) is of high interest. Due to the same reason (cost) the mixtures of PLA with other polymers are applied. In this paper the results of testing the PP/PLA mixtures of various mass ratio of the components are presented. Technical terms of preparing and processing such mixtures have been practically tested. Also the mechanical strength was determined based on the static tensile tests. The results showed that those mixtures can be repeatedly processed. Even five-times reprocessing does not cause essential drop of mechanical properties

Due to an urgent need for reducing the fast progressing climate changes, a rapid, standardized and replicable solution for the infrastructure restructuring of heat demand coverage of buildings at district and city level must be developed. As more and more communities in Europe, especially in Germany, are obligated to have plans for coverage of heat demand, city planners, energy agencies seek a tool, which will help them to design the first drafts of heating network routes, which can supply whole districts and cities with renewable energy. ArcGIS Pro Tools like Least-Cost-Path-Analysis (LCPA) and Closest Facility (CF) allow to find the shortest and “cheapest” way between the heat source and heat consumers in the analyzed areas. Starting from the community level, through the district, county, voivodeship and whole country levels, the replication of the methods for generating district heating (DH) network infrastructure can be achieved. The proposed LCPA and CF based methods help to design the most suitable and efficient DH networks in the analyzed areas. As only few open-source data input, like street networks and building footprints are needed, the methods can be implemented in all communities of the country of Poland. In this paper one example of one community of Wroclaw county, called Siechnice and surroundings is presented.

The correct classification of defects originating from partial discharges (PD) in medium-voltage (MV) switchgears with air insulation (AIS) remains a challenging research topic for scientists worldwide. In this article, the authors simulated four possible defects occurring in the power industry, including one that is a simultaneous combination of two commonly ones. In addition, the correctness of the algorithm was checked by adding a classification class without any fault. The measurement signals were recorded with TEV sensors. The effectiveness of various hy-brid-connected neural networks was tested and discussed: GoogleNet and SqueezeNet based on spectrograms, SAE with FNN, 2D-CNN with LSTM, and hybrid AE combined with CNN and LSTM. The highest effectiveness – approximately 97% – was demonstrated by the GoogleNet and SqueezeNet networks. The research results are expected to form the basis for the development of a universal and wireless capacitive sensor for monitoring the level of PD in switchgears.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

Background: To assess the incidence and characteristic of cataract surgery in Poland from 2010 to 2015 and to interpret these findings. Patients and methods: Data from all patients who underwent cataract surgery alone or in combined procedures in Poland between January 2010 and December 2015 were evaluated. Patient data were from the national database of hospitalizations maintained by National Health Fund, data on the population of Poland were obtained from Central Statistical Office of Poland. Results: In total 1,218,777 cataract extractions (alone or combined with other procedures) were performed in 1,081,345 patients during 2010 -2015. Overall, the incidence of cataract surgery increased from 5.22/1000 person-years in year 2010 to 6.17/1000 person-years in year 2015. Phacoemulsification was performed in 97.46% of cataract extractions, and 3.02% of cataract extractions were combined procedures. The rate of one-day procedures increased from 28.3% in year 2010 to 43.1% in year 2015. The probability of second-eye surgery 12 months after the first-eye surgery increased from 44% in 2010 to 73% in 2015 (log-rank test p<0.0001). Conclusion: In Poland, from 2010 to 2015 the total incidence of cataract surgery, the number of people who underwent surgery, and the numbers of one-day and combined cataract surgeries, increased significantly.

High PM10 concentrations are still a significant problem in many parts of the world. In many countries, including Poland, 50μg/m3 is the permissible threshold for a daily averaged PM10 concentration. The number of people affected by this threshold’s exceedance is challenging to estimate and requires high-resolution concentration maps. This paper presents an application of random forests for downscaling regional model air quality results. As policymakers and other end users are eager to receive a detailed resolution PM10 concentration maps, we propose a technique which utilizes the results of regional CTM (GEM-AQ, with 2.5km resolution) and local Gaussian plume model. As a result, we receive a detailed, 250-meter resolution PM10 distribution, which resembles the complex emission pattern in a foothill area in southern Poland. The random forest results are highly consistent with the GEM-AQ and observed concentration. We also discuss different strategies of data training random forest - using additional features and selecting target variables.

Reviewed are recent efforts leading to chemo-enzymatic syntheses of strongly fluorescent ribosides of nucleobase analogs, potentially applicable in analytical biochemistry and cell biology. Described are syntheses and properties of fluorescent purine, 8-azapurine and etheno-purine ribosides, obtained using various types of the purine nucleoside phosphorylase (PNP) as catalysts of ribosylation, and -ribose-1-phosphate (r1P) as a second substrate. In several instances, the ribosylation sites were different than the canonical purine N9. Some of the obtained ribosides show fluorescence yields close to 100%. Their main applications are assays of PNP, nucleoside hydrolases, and other enzyme activities both in vitro and, possibly, within the living cells, using fluorescence microscopy.

The article proposes an indirect measurement method based on a dimensional and shape analysis of forgings for the evaluation of the manufacture and the proper operation of the key elements of the crank press, in which after modernization, a quick tool assembly based on SMED (Single Minute Exchange of Die) was implemented. As a result of the introduced changes aiming at improving the forging aggregate and increasing the production efficiency, errors were observed on the manufactured products-forgings in the form of twists and joggles. The preliminary analysis showed that they can be clearances and dynamic deformation in the kinematic chain, the occurrence of side forces during automatic forging of the forging in a two-component system (a long, thin element), as well as the design and construction errors in the joining of the SMED instrument with the table tops of the press. In order to solve the presented problem, in the first place, a separate dimensional and shape analysis was made of selected elements of the press and the instrumentation with the use of the 3D scanning method with the purpose to analyze the construction tolerances of the key elements of the press geometry. Next, an evaluation of the effect of clearances and dynamic deformations of the press as well as the force distribution during the forging process was made through numerical modelling. Despite all of the above, such an approach did not make it possible to solve the problem. A proprietary method with the use of 3d reverse scanning was proposed, which allowed to solve the problem of forgings errors. Based on the measurement results and analyses for a few variants of production cycles the necessary changes was obtained, making it possible to minimize the errors and obtain proper products in respect of geometry and quality.

We examined the effects of different malolactic bacteria fermentation techniques, including a spontaneous process – a variant with a high risk of undesirable metabolites – on the bioconversion of aromatic compounds in cool-climate grape wines. During three wine seasons, red and white grape wines were produced by three different methods of malolactic fermentation induction: coinoculation, sequential inoculation, and spontaneous malolactic fermentation. Volatiles (diacetyl and the products of its metabolism, as well as selected ethyl fatty acids esters) were extracted by solid phase microextraction. Compounds were identified with multidimensional gas chromatograph GCxGC-ToFMS with ZOEX cryogenic (N₂) modulator. Sensory evaluation of the wines was also performed. We found, that the fermentation-derived metabolites examined in this study were affected by the malolactic bacteria inoculation regime. Quantitatively, ethyl lactate, diethyl succinate and ethyl acetate dominated as esters with the largest increase in the concentration. The total concentration of ethyl esters was highest for the coinoculation scenario. Whereas the highest concentration of diacetyl was noted for the spontaneous processes. A controlled malolactic fermentation, especially using the coinoculation technique, can be proposed as a safe and efficient enological practice for producing quality, cool-climate grape wines enriched with fruity, fresh and floral aromas.

Primate vision is an active process that constructs a stable internal representation of the 3D world based on 2D sensory inputs that are inherently unstable due to incessant eye movements. We present here a mathematical framework for processing visual information for a biologically-mediated active vision stereo system with asymmetric conformal cameras. This model utilizes the geometric analysis on the Riemann sphere developed in the group-theoretic framework of the conformal camera, thus far only applicable in modeling monocular vision. The asymmetric conformal camera model constructed here includes the fovea’s asymmetric displacement on the retina and the eye’s natural crystalline lens tilt and decentration, as observed in ophthalmological diagnostics. We extend the group-theoretic framework underlying the conformal camera to the stereo system with asymmetric conformal cameras. Our numerical simulation shows that the 1 theoretical horopter curves in this stereo system are conics that well approximate the empirical longitudinal horopters of the primate vision system.

In this paper, a regression model between neutron star crust-core pressure and the symmetry energy characteristics was estimated using the Akaike information criterion and the adjusted coefficient of determination Radj2. Based on the obtained regression function, the most probable value of the transition density, which should characterize the crust-core environment of the sought physical neutron star model, was determined. An anti-correlation was found between this transition density and the main characteristic of the symmetry energy, i.e., its slope L.

The aim of the study is to assess enjoyment and intensity of physical exercise while practicing physical activity (PA) in immersive virtual reality (IVR) using innovative training devices (omni-directional Omni treadmill and Icaros Pro flight simulator). The study also contains the results of subjective research on the usefulness of such a form of PA in the opinion of users. In total, 61 adults (10 women and 50 men) took part in the study. To assess the enjoyment level (EL) Interest/Enjoyment subscale of Intrinsic Motivation Inventory (IMI) was used. Exercise intensity was assessed during 10-minute sessions of active video games (AVGs) in IVR based on heart rate (HR). The average enjoyment level during physical exercise in IVR on the tested training devices was relatively high (Omni 5.74 points, Icaros 5.60 points). In the opinion of the majority of participants, AVGs on IVR training devices constitute a sufficiently useful form of movement to meet the needs of PA practiced in free time, and they can even replace some of the classic forms of movement. Intensity of PA during games on training devices was at the level recommended for health benefits for 92% (Omni) and 84% (Icaros Pro) of its duration. Based on the conducted research, it can be assumed that AVGs in IVR using a multi-directional treadmill and a flight simulator can be an effective tool for increasing participation in health-oriented PA.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and &gt;115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

Early detection that results in early warning of forest fires occurrences in Indonesia, which are strongly related to land management practices (including peatlands), is necessary to mitigate land and forest fires in Indonesia. Riau has been chosen in this study because of its vulnerability to forest fires. The remoteness of this region is one reason for developing alternative warning tools using meteorological and social media information. This study identified tweets related to fires using carefully selected keywords, geoparsed to select messages relevant to fire occurrences, and binned within several Indonesian sub-regions in Riau Province. Content analysis was performed for 31 related online local newspapers. Assessment to study the correlation between meteorological and Twitter information with the forest fires was conducted. Existing approaches that the BMKG and other Indonesian agencies use to detect fire activities are reviewed, and a novel approach based on crowdsourcing of tweets is proposed. The results show a correlation between meteorological information and Twitter activity with satellites derived hotspot information. The policy implications of these results suggest that information should be included in the fire management system in Indonesia to support fire early detection as part of fire disaster mitigation efforts.

Previous reviews have investigated machine learning (ML) models used to predict the risk of developing preeclampsia but have not described how the ML models are intended to be deployed throughout pregnancy or feature performance. The aim of this study is to provide an overview of the existing ML models and their intended deployment patterns and performance along with identified features of high importance. This review used the Preferred Reporting Items for Systematic Reviews and Meta-Analyses 2020 guidelines. PubMed, Engineering Village, and the Association for Computing Machinery were searched between January and February 2024. A total of 86 studies were found of which 14 were included. Out of 12 studies, eight showed the intent to use the ML model as a single-use, two intended a dual-use, and two intended multiple-use. A total of seven studies listed the features of the highest importance. Systolic and diastolic blood pressure were listed along with mean arterial pressure to be of high importance. Out of four studies intending to use the ML model more than a single-use, three of them were conducted in the years 2023 and 2024, whereas the remaining study is from 2011. No ML model emerged as superior across the subgroups of PE. Utilizing body mass index and either mean arterial pressure or diastolic blood pressure and systolic blood pressure may benefit the performance. The deployment patterns are mainly single use being within the gestation weeks 11+0 to 14+1.

The forming mechanism of clinch joints, for various materials arrangement, using a punch and a rigid die, is well known. The basic technological parameter of the process is the parameter X – the minimal thickness of the embossment. Usually, the lower the X parameter, the greater the joint interlock. This paper presents the possibility of forming a pressed joint for two 1.5 [mm] thick sheets made of HX340 steel. The joint was formed using an additional deformable steel rivet with a hardness of 400HV1. Different values of rivet pressing below the initial surface of the upper sheet were chosen: 0, 0.15, 0.30, 0.45 and 0.60 (in [mm]). The punch positioning accuracy was 0.01 [mm]. For the mentioned rivet pressing distances, forming tests were performed using an ‘‘SKB’’ die with three die depths: 1.45, 1.60 and 1.75 (in [mm]). Observations and measurements of the characteristic geometric dimensions of the interlock were made. Furthermore, the strength of the clinch-riveted joints was analysed. The greater the rivet pressing distance, the larger the interlock parameters. Furthermore, depending on the size of the rivet pressing distance, different failure mechanisms of the lap joint were observed in the tensile shear tests.

Based on the example of wintering waterbirds in the Baltic Sea, we show a method that is useful in setting priorities for species management. The Value Factor (VF) shows which species in the region are the most valuable and on which ones conservation measures need to focus. Every year 4,400,000 waterbirds winter in the Baltic. Among which the highest priority species are velvet scoter Melanitta fusca (VS, VF=153) and long-tailed duck Clangula hyemalis (LTD, VF=204): 74% and 40%, respectively, of the world populations and over 90% of the EU populations of both species spend the winter there. Management plans (MP) regulating the protection of marine Natura 2000 sites (MPA) and dedicated to the protection of VS and LTD have been implemented in 65% and 51%, respectively, of MPAs in the Baltic. Poland, a key country for the survival of these species, has not implemented a single MP despite the existence of documentation confirming their crucial importance for seaducks, and on the pressures occurring there. We suggest using the VF concept to define priority species. On this basis, it will be possible to identify gaps in the protection of the most seriously threatened species and implement conservation measures in the most appropriate sites

The aim of this study was to identify the differences in functional fitness and quality of life among women over 60 years of age depending on their level of objectively measured physical activity (PA) according to Global Recommendations on Physical Activity for health. The study used cross-sectional design with 213 volunteered women over 60 years of age. Physical activity was monitored for 7 days of the week using Actigraph Gt3x monitor. The Senior Fitness Test battery and Hand-grip strength tests were performed to assess functional fitness. Quality of life was self-reported using short version of WHOQOL-brief questionnaire. Women who met the PA recommendations achieved slightly better results in most functional tests and all domain of quality of life. The significant differences were found in upper body strength, dynamic balance and social relationships domain of quality of life. Physical activity programs developed on the basis of WHO recommendations have the potential to improve functional capacity and quality of life. However, further experimental studies in this area are required.

Timely mitosis is critically important for the early embryo development. It is regulated by the activity of the ubiquitously conserved CDK1 kinase. The dynamics of CDK1 activation must be precisely controlled to assure physiologic and timely entry into mitosis. Recently, a known S-phase regulator CDC6 emerged as a key player in the mitotic CDK1 activation cascade in early embryonic divisions, operating together with Xic1 as a CDK1 inhibitor upstream of the Aurora A- and PLK1 kinases, both CDK1 activators. Herein we review the molecular mechanisms that underlie the control of the mitotic timing, with special emphasis on how CDC6/Xic1 function impacts CDK1 regulatory network. We focus on the presence of two independent mechanisms inhibiting the dynamics of CDK1 activation: Wee1/Myt1- and CDC6/Xic1-dependent, and how they cooperate with CDK1 activating mechanisms. As a result we propose a comprehensive model integrating CDC6/Xic1-dependent inhibition into the CDK1-activation cascade. The physiological dynamics of CDK1 activation appear to be tuned by the system of multiple inhibitors and activators and their integrated modulation ensures concomitantly both the robustness and certain flexibility of the control of this process. Identification of multiplied activators and inhibitors of CDK1 activation upon M-phase entry allows a better understanding of why cells divide at a specific time, and how the pathways involved in the timely regulation of the cell division are all integrated to precisely tune the control of mitotic events.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

Mushroom production in Poland is an important and dynamically developing element of diverse agriculture. Mushroom spent compost (MSC) is major waste generated during production, i.e., MSC: mushrooms is ~5:1. To date, the main use of MSC is soil application as organic fertilizer. To date, several methods of MSC treatment have been researched and developed including production of compost, bioethanol, biogas, enzyme lactase, xylo-saccharides, and hydrogen. Torrefaction may be considered a novel approach for biomass valorization. Thus, we are pioneering the potential use of MSC valorization via torrefaction. We explored valorizing the waste biomass of MSC via thermal treatment – torrefaction (‘roasting’) to produce biochar with improved fuel properties. Here for the first time, we examined and summarized the MSC torrefaction thermogravimetric analyses, fuel properties data of raw biomass of MSC and biochars generated from MSC via torrefaction. The effects of torrefaction temperature (200~300 °C), process time (20~60 min), on fuel properties of the resulting biochars were summarized. The dataset contains results of thermogravimetric analysis (TGA) as well as proximate analyses of MSC and generated biochars. The presented data are useful in determining MSC torrefaction reaction kinetics, activation energy and to further techno-economical modeling of the feasibility of MSC valorization via torrefaction. MSC torrefaction could be exploited as part of valorization resulting from a synergy between an intensive mushroom production with the efficient production of high-quality renewable fuel.

Cadherins are a group of membrane proteins responsible for cell adhesion. They are crucial for cell sorting and recognition during the morphogenesis, but also play many other roles such as assuring tissue integrity and resistance to stretching, mechanotransduction, cell signaling, regulation of cell proliferation, apoptosis, survival, carcinogenesis, etc. Within the cadherin superfamily, the E- and N-cadherin have been especially well studied. They are involved in many aspects of sexual development and reproduction, such as germline development and gametogenesis, gonad development and functioning, and fertilization. E-cadherin is expressed in the primordial germ cells, (PGCs) and also participates in PGC migration to the developing gonads where they become enclosed by the N-cadherin-expressing somatic cells. The differential expression of cadherins is also responsible for the establishment of the testis or ovary structure. In the adult testes, the N-cadherin is responsible for the integrity of the seminiferous epithelium, regulation of sperm production, and the establishment of the blood-testis barrier. Sex hormones regulate the expression and turnover of N-cadherin influencing the course of spermatogenesis. In the adult ovaries, E- and N-cadherin assure the integrity of ovarian follicles and the formation of corpora lutea. Cadherins are expressed in the mature gametes, and facilitate the capacitation of sperm in the female reproductive tract, and gamete contact during fertilization. The germ cells and accompanying somatic cells express a series of different cadherins, however, their role in gonads and reproduction is still unknown. In this review, we show what is known and unknown about the role of cadherins in the germline and gonad development, and suggest the topics for future research.

1) Background: A survey of biogenic amines profile in opened wine bottles has been established. Opened bottles of red and white wine were submitted to different temperature as well as different kind of stopper (screw cap, cork stopper) and use of vacuum devices. A total of six wine made from different variety of grapes were obtained from Polish vineyard places in different region of Poland; 2) Results: DLLME-GC-MS procedure for biogenic amines determination was validated and applied for wine samples analysis. The total content of BAs in white wines ranged from 442 µg/L to 929 µg/L, while in red wines ranged from 669 µg/L to 2244 µg/L the set of just opened wine samples. The most abundant biogenic amines in the six analysed wines were histamine and putrescine; 3) Conclusion: Considering the commercial availability of the analysed wines, there was no relationship between the presence of biogenic amines in a given wine and their availability on the market. However, it was observed that the different storage conditions employed in this experiment affect not only the biogenic amines profile, but also the pH. The results were confirmed by chemometric analysis.

Background: Retinal vascular abnormalities may be associated with glaucomatous damage. Adaptive optics (AO) is a new technology that enables analysis of retinal vasculature at the cellular level in vivo. The purpose of this study is to evaluate retinal arteriolar parameters using the adaptive optics fundus camera (AO -FC) rtx1 in patients with primary open-angle glaucoma (POAG) at different stages and to investigate the relationship between these parameters and changes in optical coherence tomography (OCT) and perimetry. We wanted to assess whether vascular changes could be a cause or effect of glaucomatous damage. Methods: Parameters of retinal supratemporal and infratemporal arterioles (wall thickness (WT), lumen diameter (LD), total diameter (TD), wall-to-lumen ratio (WLR), and cross-sectional area of the vascular wall (WCSA)) were analysed with the rtx1 in 111 POAG eyes, divided into three groups according to the severity of disease and 70 healthy eyes in correlation of structural defects in retinal nerve fibre layer and visual fields defects. Results: Compared with the control group, the POAG groups showed significantly smaller TD and LD values (p<0,05) and significantly higher WLR and WT values (p<0,05) for supratemporal and infratemporal arterioles. Rtx1 parameters significantly correlated with OCT parameters (retinal nerve fibre layer, ganglion cell complex and rim area) and visual field parameters (mean deviation and pattern standard deviation) (p<0.05). Conclusion:  The results suggest that vascular dysfunction may be involved in POAG pathogenesis and neurodegenerative damage, even at the very early stage of glaucoma, without visual field defects.

Background: With the increasing global incidence of diabetes mellitus (DM), diabetic retinopathy (DR) has become one of the leading causes of blindness in developed countries. DR leads to changes in retinal neurons and microcirculation. Rtx1TM (Imagine Eyes, France) is a microscope that allows histological visualisations of cones and retinal microcirculation throughout the DM duration. Objective: This study aimed to analyse the cones and retinal microvascular changes in 50 diabetic individuals and 18 healthy volunteers. The patients participated in the initial visit and two fol-low-up appointments: one and two years after the study, beginning with rtx1 image acquisition, visual acuity assessment, macular OCT scans and blood measurements. Results: The study revealed significant differences in the cone density, mosaic arrangement and vascular morphology between healthy and diabetic patients. The final measurements have shown decreased photoreceptor and microvascular parameters in the DR group compared to the control group. Furthermore, in the 2-year follow-up, both groups' rtx1-acquired morphological changes were statistically significant. Conclusions: Rtx-1 technology was successfully used as a non-invasive method of photoreceptors and retinal vasculature assessment over time in patients with diabetic retinopathy. The study has revealed a trend toward more vascular morphological changes occurring over time in diabetic patients.

The use of swine manure as a source of plant nutrients is one alternative to synthetic fertilizers. However, conventional manure application with >90% water and a low C:N ratio results in soil C loss to the atmosphere. Our hypothesis was to use biochar as a manure nutrient stabilizer that would slowly release nutrients to plants upon biochar-swine manure mixture application to soil. The objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and plant-available macro and micronutrients in greenhouse-cultivated corn (Zea mays L.) and soybean (Glycine max (L.) Merr.). Neutral pH red oak (RO), highly alkaline autothermal corn stover (HAP), and mild acidic Fe-treated autothermal corn stover (HAPE) biomass were pyrolyzed to prepare biochars. Each biochar was surface-applied to swine manure at a 1:4 (biochar wt/manure wt) ratio to generate mixtures of manure and respective biochars (MRO, MHAP, and MHAPE). Conventional manure (M) control and manure-biochar mixtures were then applied to the soil at a recommended rate. Corn and soybean were grown under these controls and treatments (S, M, MRO, MHAP, and MHAPE) to evaluate the manure-biochar impact on soil quality, plant biomass yield, and nutrient uptake. Soil OM significantly (<0.05) increased in all manure-biochar treatments; however, no change in soil pH or N was observed under any treatment. No difference in soil ammonium between treatments was identified. There was a significant decrease in soil M3-P and soil NO₃^- for all manure-biochar treatments compared to the conventional M. However, the plant biomass nutrient concentrations were not significantly different from control manure. Moreover, an increasing trend of N and decreasing trend of P in the plant under all biochar-manure treatments than the controls were noted. This observation suggests that the presence of biochar is capable of influencing the soil N and P in such a way as not to lose those nutrients at the early growth stages of the plant. In general, no statistical difference in corn or soybean biomass yield and plant nutrient uptake for N, P, and K was observed. Interestingly, manure-biochar application to soil significantly diluted the M3-extractable soil Cu and Zn concentrations. The results attribute that manure-biochar has the potential to be a better soil amendment than conventional manure application to the soil.

The link between scoliotic deformity and bone metabolism in adolescent idiopathic scoliosis (AIS) has not been well researched. Moreover, the data concerning the cross-talk between fat tissue content/hormonal activity and bone markers in this group of patients are lacking. The objective of this study was to correlate the extent of scoliotic-curve severity with the bone turnover vs. leptin level and nutritional status in girls with AIS. The study encompassed 77 AIS girls, aged 14.7 ± 2.17 years. Scoliotic curve severity assessed by Cobb’s angle was categorized as mild (10-19o) moderate (20-39º) or severe (≥40º). Corrected height, weight, waist and hip circumferences were measured and body mass index (BMI), corrected height Z-score, BMI Z-score and waist/height ratio (WHtR) were calculated for the entire group. Body composition parameters: fat mass (FAT), fat-free mass (FFM) and predicted muscle mass (PMM) were determined using a bioelectrical impedance analyzer. Bone turnover markers (osteocalcin (OC) and amino terminal of collagen cross-links NTx) and leptin levels were assessed in serum. Multiple regression analysis showed that, OC, NTx (negatively with p<0.05) and leptin (positively with p<0.01) were significantly associated with curve severity in AIS girls. Moreover, Cobb’s angle was positively correlated with W/HtR (p<0.01)and FAT (p<0.05). One-way analysis of variance (ANOVA) revealed significant differences in leptin (p<0.05 vs. mild only), OC (p<0.05 vs. mild and moderate)) and W/HtR (p<0.01 and p<0.05 vs. mild and moderate respectively) between the three AIS severity subgroups. OC was significantly lower in the severe AIS subgroup, while leptin and W/HtR were significantly higher. Significant correlations between leptin and anthropometrical parameters as BMI z-score and W/HtR were shown. Leptin level correlated also significantly with BMI z score (p<0.001), W/HtR (p<0.0001) and body composition parameters (p<0.000001). Moreover, there was a significant negative correlation between NTx and leptin level (p<0.05). Bone metabolism in AIS girls seems to be altered and significantly related to the scoliotic curve severity. Leptin may be a crucial link in the cross-talk between bone turnover and body composition in this group of patients. Further studies concerning this topic are needed.

In Poland, the mountainous and hilly regions until recently were territories with unbalanced and poor diet quality, especially in early spring. Wild edible plants were or still are influential in supplementing a human diet. One of the earliest wild edible plants to appear in the growing season, characteristic of a broad swath of Europe from Ukraine to Germany, remains wild (bear) garlic (Allium ursinum L.). This paper assesses the impact of the vegetation site and preservation methods on selected parameters of the chemical composition of bear garlic. In addition, the connection between its genome pattern and chemical composition was assessed. The plants were collected in three locations in the Carpathian foothills, and the reference sample was plants collected in the lowlands. The site from which the raw material was harvested has a statistically significant effect on the chemical composition of the preserved leaves of bear garlic. The profiles of the analysed components differed in the material from a different site. Bear garlic leaves from mountainous areas had more analyzed components than those obtained from the lowland sites. Moreover, the material from the lowlands had a different genetic pattern from the leaves from the mountainous areas..

Biowaste generated in the process of Oxytree cultivation and logging represents a potential source of energy. Torrefaction (a.k.a. low-temperature pyrolysis) is one of the methods proposed for the valorization of woody biomass. Still, energy is required for the torrefaction process during which the raw biomass becomes biochar with fuel properties similar to lignite coal. In this work, models describing the influence of torrefaction temperature and residence time on the resulting fuel properties (mass and energy yields, energy densification ratio, organic matter and ash content, combustible parts, lower and higher heating values, CHONS content, H:C and O:C ratios) were proposed according to the Akaike criterion. The degree of the models’ parameters matching the raw data expressed as the determination coefficient (R²) ranged from 0.52 to 0.92. Each model parameter was statistically significant (p<0.05). Estimations of the value and quantity of the produced biochar from 1 Mg of biomass residues were made based on two models and a set of simple assumptions. The value of torrefied biochar (€123.4·Mg^-1) was estimated based on the price of commercially available coal fuel and its lower heating value (LHV) for biomass moisture content of 50%, torrefaction for 20 min at 200 °C. This research could be useful to inform techno-economic analyses and decision-making process pertaining to the valorization of pruned biomass residues.

Part II, like Part I, discusses geometry, kinematics and statics in detail without taking into account power losses in meshing. The main goal of Part II, however, is to prove that there are complex and structurally coupled planetary gear systems, i.e. containing a closed circuit in which no circulation of power flow is generated. The power flow analysis is also carried out using the direct method, with a slight modification in the way of writing the equations identifying active and passive gears, i.e. at the same time the directions of power flow on all transmission paths. The analysed planetary gear system (PGS) is characterised by mobility equal to 1, i.e. single degree of freedom (DoF). It consists of three subsystems in the form of the 2KH type planetary units connected in series-parallel, specially selected to demonstrate the thesis of this paper. It consists of three subsystems in the form of single planetary subsystems of the 2KH type connected series-parallel, specially chosen to illustrate the thesis of this paper.

Nowadays, digitalization and automation in both industrial and research activities is a driving force for innovations. In recent years, Machine Learning (ML) techniques - the subset of Artificial Intelligence - have been widely applied as a key tool to automize and digitalize numerous in-dustrial processes. ML models can predict specific features, like materials' lifetime in a heating device, based on recently trained algorithms with applied input data. The results of ML algorithms are easy to interpret and can significantly decrease the time of research and decision-making, thus, substituting the trial-error approach. This work presents the state of the art in the application of Machine Learning in the investigation of MgO-C refractories for the steel industry. Also, the work presents an overview of the most commonly used ML algorithms in refractory engineering. So far published results confirm the high performance of ML, e.g., for prediction of oxidation behaviour, optimum graphite content and wear rate of MgO-C refractories, or for clustering materials based on various fused and sintered MgO sources into groups with similar corrosion resistance, thus, permitting to reduce expensive fused raw materials content. Most of the presented works were positively validated via experiment.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.

Doxorubicin, a member of the anthracycline family, is a common anticancer agent often used as a first line treatment for the wide spectrum of cancers. Doxorubicin-based chemotherapy, although effective, is associated with serious side effects, such as irreversible cardiotoxicity or nephrotoxicity. Those often life-threatening adverse risks, responsible for the elongation of the patients' recuperation period and increasing medical expenses, have prompted the need for creating novel and safer drug delivery systems. Among many proposed concepts, polymeric nanocarriers are shown to be a promising approach, allowing for controlled and selective drug delivery simultaneously enhancing its activity towards cancerous cells and reducing toxic effects on healthy tissues. This article is a chronological examination of the history of the work progress on polymeric nanostructures, designed as efficient doxorubicin nanocarriers, with the emphasis on the main achievements of 2010-2020. Numerous publications have been reviewed to provide an essential summation of the nanopolymer types and their essential properties, mechanisms towards efficient drug delivery, as well as active targeting stimuli-responsive strategies that are currently utilized in the doxorubicin transportation field.

Downwind odor characteristics can be very different depending upon the size of the upwind point-source, interim topography, and wind conditions. At one extreme, the downwind odor plume from a relatively large, confined animal feeding operation (CAFO), located on a flat open plain and under stable, near-straight-line wind conditions can be rather broad, sustained and predictable relative to a fixed receptor site downwind. In contrast, the plume from a small point-source (e.g., a roof vent stack) located on irregular topography and under rapidly shifting wind conditions can be intermittent and fleeting. These transient odor events can be surprisingly intense and offensive, in spite of their fleeting occurrence and perception. This work reports on efforts to optimize an environmental odor sampling strategy, which is optimized for the challenges of (1) sampling of such transient odor 'spikes' and (2) the prioritization of odors/odorants from multiple, closely co-located point-sources, under such transient event conditions. Protocol refinement has emerged by way of 2 environmental odor assessment projects which have been undertaken on behalf of the Missouri Department of Natural Resources. The challenge of transient odor events has been mitigated utilizing rapid, odor cued whole-air grab capture sampling into metalized-FEP gas sampling bags, followed by immediate adsorption transfer onto SPME fibers or sorbent tubes for stabilization during the shipment and storage interval between collection and final analysis. Initial results demonstrated approximately 11 fold increases in target odorant yields for 900 mL sorbent tube transfers from 2-3 second 'burst' odor event bag-captures, as compared to equivalent direct collections at the same downwind receptor location but during perceived (stable) odor 'lull' periods. Results-to-date targeting refinement and field trials of this integrated environmental odor assessment strategy are presented. Preliminary application targeting general odor sampling and point-source differentiation utilizing tracer gases is also presented.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Tetrathiolate zinc fingers are potential targets of oxidative assault under cellular stress conditions. We used the synthetic 37-residue peptide representing the tetrathiolate zinc finger domain of the DNA repair protein XPA, acetyl-DYVICEECGKEFMSYLMNHFDLPTCDNCRDADDKHK-amide (XPAzf) as a working model to study the reaction of its Zn(II) complex (ZnXPAzf) with hydrogen peroxide and S-nitrosoglutathione (GSNO), as oxidative and nitrosative stress agents, respectively. We also used the Cd(II) substituted XPAzf (CdXPAzf) to assess the situation of cadmium assault, which is accompanied by oxidative stress. Using electrospray mass spectrometry (ESI-MS), HPLC, and UV-vis and circular dichroism spectroscopies we demonstrated that even very low levels of H2O2 and GSNO invariably cause irreversible thiol oxidation and concomitant Zn(II) release from ZnXPAzf. In contrast, CdXPAzf was more resistant to oxidation, demonstrating the absence of synergy between cadmium and oxidative stresses. Our results indicate that GSNO cannot act as a reversible modifier of XPA, and rather has a deleterious effect on DNA repair.

Comparisons of power flows and efficiencies in two structurally quite similar cylindrical series-parallel planetary gear systems (PGSs) were performed in three separate parts of this paper. Each of these single degree of freedom (DoF) systems consists of three different 2KH subsystems connected in series-parallel. The main goal was to prove that apart from complex, structurally and dynamically coupled PGSs, there are also complex and only structurally coupled PGSs, in which the phenomenon of power flow circulation inside closed loops does not occur. Such a half-coupled type of PGS is herein called pseudo-coupled. Therefore, Part I discusses in detail the geometry, kinematics and statics of coupled PGSs in order to determine power flow paths. A comparison of the directions of power flow in both types of PGSs can be made in Part II after determining the power flow paths in the second planetary gear in a similar way. The directions of power flow in both types of PGSs were determined in a relatively simple way, thanks to the distinction between active and passive torques and thus active and passive shafts of individual subsystems. The efficiency comparison made in Part III will show whether power circulation has an influence on the efficiency value, at least in these two types of PGSs.

The aim of the paper is to identify the most likely factors that determine the demand for Renewa-ble Energy Consumption (R.E.C.) in European countries. Although in Europe a high environmen-tal awareness is omnipresent, countries differ in scope and share of R.E.C. due to historical ener-getic policies and dependencies, investments into renewable and traditional energetic sectors, R&D development, structural changes required by energetic policy change, and many other fac-tors. The study refers to a set of macroeconomic, institutional, and social factors affecting energetic renewable policy and R.E.C. in selected European countries in two points of time: i.e., before and after the Paris Agreement. The Bayesian Average Classical Estimates (BACE) is applied to indicate the most likely factors affecting R.E.C. in 2015 and 2018. The comparison of the results reveals that the G.D.P. level, nuclear and hydro energy consumption were the determinants significant in both analyzed years. Furthermore, it became clear that in 2015 the R.E.C. depended strongly on the energy consumption structure, while in 2018, the foreign direct investment and trade openness played their role in increasing renewable energy consumption. The direction of changes is positive and complies with sustainable development goals (S.D.G.s).

Introduction. Congenital muscular torticollis (CMT) is an asymmetrical head positioning resulting from structural changes in the sternocleidomastoid muscle (SCM) that occurs early in a child’s development period or due to perinatal trauma. Children with CMT exhibit a marked imbalance in tension between the SCMs. When the clinical picture is typical, an ultrasound scan is performed to reveal characteristic lesions, such as tissue fibrosis or post-traumatic changes. Early diagnosis of CMT in newborns and implementation of treatment offer the chance of a complete cure. Torticollis treatment aims to rebuild the SCM's normal function by restoring its anatomical length, normal cervical spine mobility and muscle flexibility to enable regular head movements. Surgical treatment is performed when conservative methods fail to improve the patient’s condition. Indications for surgery include marked shortening of the SCM, persistent fibrosis in the muscle, constant head and facial asymmetry, and rotation or lateral flexion in the cervical spine restricted by > 15°. After hip dislocations and foot deformities, pediatric orthopedics addresses torticollis as the third most common congenital anomaly. Aim. This study was a retrospective analysis of 111 children diagnosed and treated due to CMT. Methods. The following were determined: the relationship between the side of CMT location and the type of delivery (cc vs. natural), between the body weight at birth and the side of CMT location, between the extent of SCM thickening and the type of delivery, and the incidence of CMT depending on the order of delivery. Results and conclusions. The analysis showed that CMT was more common in boys 61(54%) than in girls 51(46%), which may be related to the greater birth weight in boys. Of the pediatric patients with CMT, 76% were primiparous. More often, children born via natural delivery had left-sided torticollis with a more significant broadening of the SCM on ultrasound scans than right-sided torticollis. Theories of torticollis development pathophysiology should be deepened, systematized, and further researched.

This paper investigates the theoretical foundation for developing renewable geothermal resources locally. For this reason, we pay attention to the role of communities in geothermal development. This study presents arguments for a framework that approaches the geothermal resources as an endogenous factor of community development. To analyse it, we create a model that explains the local economic characters of the geothermal exploitation beyond its geological conditions. It aims to conceptualise a community based geothermal development standard referring to the endogeneity principle. Geothermal energy is given attention since the characteristics of this resource determine its use locally. We argue that the role of communities in geothermal exploitation is pivotal in the process of green growth for further expansion of geothermal energy use.

As the global demand for renewable energy continues to rise, biogas technology has emerged as a promising solution for sustainable energy generation. This review article presents the advantages of biogas technologies and extensively discusses the main principles of biogas production in the methane fermentation process. In this respect, the main parameters of the process, which require monitoring and are at the same time decisive for its course and efficiency are described, the principles of substrate selection are discussed and the necessity and advantages of the use of organic waste according to the model of a circular economy and the concept of sustainable development, are indicated. The part on biogas production is summarised with an explanation of the necessity to treat and purify biogas, taking into account the share of methane extracted. A special place in this paper is devoted to the design, construction, functioning and operation of biogas plants, based on both scientific and practical aspects. In conclusion of this chapter, the economic aspects and profitability of operating biogas plants are discussed, taking into account, in a theoretical balance sheet – in addition to investment and operating costs and the availability and cost of raw materials – the possibilities of producing and using electricity and heat, as well as environmental and social benefits. The article concludes with a discussion of opportunities and barriers to the development of biogas plants, pointing to: financial issues, access to feedstock, political regulations, public awareness and the geopolitical situation as key factors issues related to biogas plants – in different regions of the world.

Atopic dermatitis (AD) is common inflammatory dermatosis, typically with chronic and recurrent course, which significantly reduces the quality of life. Sleep disturbances are considered to be remarkably burdensome ailments in the patients with AD, and are routinely included during assessment of disease severity. Therefore, endogenous substances engaged in the control of circadian rhythms might be important in pathogenesis of AD and, possibly, be used as biomarkers of disease severity or even in development of novel therapies. Melatonin (MT), the indoleamine produced by pineal gland (but also by multiple other tissues, including skin), plays a pivotal role in maintaining the sleep/wake homeostasis. Additionally, it possess strong antioxidant and anti-inflammatory properties, which might directly link chronic skin inflammation and sleep abnormalities characteristic of AD. The objective of this work is to systematically present and summarize the results of studies (both experimental and clinical) that investigated the role of MT in the AD, with focus on the antioxidant and immunomodulatory effects of MT.

The study examined the effect of noninvasive crown retrieval/reuse process using erbium-doped yttrium aluminum garnet laser (Er:YAG). Twenty-six extracted human teeth were prepared for a crown. The crown was milled using lithium disilicate (LD) and zirconia (Z) materials, n=13 per group, 3 for scanning electron microscopy (SEM). The crown was luted using composite resin cement and subjected to a laser retrieval process. After the retrieval process, the crown was cleaned, recemented and laser-retrieved two more times, without and with additional tooth reduction mimicking clinical refreshment of dentin. Retrieval time and temperature were analyzed using analysis of variance (ANOVA). Surface changes were observed through SEM. The retrieval times were 267.1±130.43, 220±79.09, 277.1±126.44, 368.4±136.14, 355±159.39, and 419.2±121.36 seconds for first, second, third LD and Z groups, respectively (p=.009). The maximal temperatures were 23.95.1±1.89°C, 24.86±2.01°C, 24.17±1.53°C, 22.88±1.51°C, 24.03±1.74°C, and 21.99±1.32°C for for first, second, third LD and Z groups, respectively (p=.006). Er:YAG laser crown removal is an effective retrieval tool for all-ceramic crowns. Minimal changes to teeth and crowns were observed following laser irradiation.

It is expected that due to the new UE regulation focus on waste management, managing kitchen waste will become more important in the future, especially in households. It is, therefore, crucial to develop user-friendly and odor-free containers to store kitchen waste. The study aimed to test the effectiveness of compost biochar in reducing noxious odors and volatile organic compounds (VOCs) released during kitchen waste storage. Varying quantities of compost biochar (0%, 1%, 5%, and 10%) were added to food waste samples and incubated for seven days at 20℃. VOCs released were analyzed on days 1, 3, and 7 of the storage simulation process. The results indicated that adding 5-10% of composts’ biochar to kitchen waste significantly reduced emissions in 70% of detected VOCs compounds. Additionally, Compost's biochar can be used to eliminate potential odor components and specific dangerous VOCs such as ethylbenzene, o-xylene, acetic acid, and naphthalene. A new composts’ biochar with a unique composition was particularly effective in reducing VOCs and could be an excellent solution for eliminating odors in kitchen waste con-tainers.

Experimental optimization of analytical methods based on solid-phase microextraction (SPME) is a complex and labor-intensive process associated with uncertainties. Using the theoretical basics of SPME and finite element analysis software for the optimization proved to be an efficient alternative. In this study, an improved finite element analysis-based model for SPME of volatile organic compounds (VOCs) by porous coatings was developed mainly focussing on the mass transport in coatings. Benzene and the Carboxen/polydimethylsiloxane (Car/PDMS) coating were used as the model VOC and a porous SPME coating, respectively. It has been established that in the coating, volumetric fractions of Carboxen, PDMS, and air are 33, 42 and 24%, respectively. Knudsen diffusion in micropores can slow down a mass transport of analytes in the coating. When PDMS was considered as the solid part of the coating, lower root-mean-square deviation of the modeling results from experimental data was observed. It has been shown that the developed model can be used to model the extraction of VOCs from air and water samples encountered in a typical SPME development method procedure. It was possible to determine system equilibration times and use them to optimize sample volume and Henry’s law constant. The developed model is relatively simple, fast, and can be recommended for optimization of extraction parameters for other analytes and SPME coatings. The diffusivity of analytes in a coating is an important property needed for improved characterization of existing and new SPME polymers and analytical method optimization.

Plant and animal agriculture is a part of a larger system where the environment, soil, water, nutrient management interact. Biochar (a pyrolyzed biomass) has been shown to affect the single components of this complex system positively. Biochar is a soil amendment, which has been documented for its benefits as soil enhancer particularly to increase soil carbon, improve soil fertility, and better nutrient retention. These effects have been documented in the literature. Still, there is a need for a broader examination of these single components and effects that aims at the complementarity and synergy attainable with biochar and the animal and crop production system. Thus, we report a comprehensive dataset documenting the interactions of biochar with manure, soil, and plants. We evaluated three biochars mixed with manure alongside both manure and soil controls for improvement in soil quality, reduction in nutrient movement, and increase in plant nutrient availability. We explain the experiments and the dataset which contains the physicochemical properties of each biochar-manure mixture, the physicochemical properties of soil amended with each biochar-manure mixture, and the biomass and nutrient information of plants grown in biochar-manure mixture amended soil. This dataset is useful for continued research examining both the short and long-term effects of biochar-manure mixtures on both plant and soil systems. In addition, these data will be beneficial to extent the findings to field settings for practical and realized gains.

Selection of efficient corrosion inhibitors requires detailed knowledge regarding interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. Position of functional groups between different isomers is often overlooked but not less important since factors like steric hinderance may significantly affect the adsorption mechanism. In this study we have presented how different dihydroxybenzene isomers interact with aluminium alloy 5754 surface, reducing its corrosion rate in bicarbonate buffer (pH = 11). We have shown the highest inhibition efficiency among tested compounds belongs to catechol at 10 mM concentration, although differences were moderate. Utilization of novel impedance approach to adsorption isotherm determination allowed to confirm that while resorcinol chemisorbs on aluminium surface, catechol and quinol follows ligand exchange model of adsorption. Unlike catechol and quinol, the protection mechanism of resorcinol is bound to interaction with insoluble aluminium corrosion products layer and was only found efficient at concentration of 100 mM (98.7%). The aforementioned studies were confirmed with scanning electron microscopy and x-ray photoelectron spectroscopy analyses. There is a significant increase of the corrosion resistance offered by catechol at 10 mM after 24 h exposure in electrolyte: from 63 to 98%, with only negligible changes in inhibitor efficiency observed for resorcinol at the same time. However, in the case of resorcinol a change in electrolyte color was observed. We have revealed that the differentiating factor is the keto-enol tautomerism. The NMR studies of resorcinol indicate the keto form in structure in presence of NaOH, while the chemical structure of catechol does not change significantly in alkaline environment.

Equine metabolic syndrome (EMS) is a major health threat in veterinary endocrinology medicine worldwide, and there is growing interest in utilizing molecular agents for modulation of hepatocyte function for potential clinical applications with recent studies showing promising results in the inhibition of PTP1B on adipose-derived stromal cells. In this study, we investigated the effects of MSI-1436 on equine hepatic progenitor cells (HPCs) in terms of their proliferative activity, glucose uptake, and mitochondrial morphogenesis under lipotoxic condition. Our study found that MSI-1436 promotes the entry of HPCs in the cell cycle and rescues them from palmitate-induced apoptosis by regulating mitochondrial dynamics and biogenesis. MSI-1436 also increases glucose uptake and protects HPCs from palmitate-induced stress by reorganizing the morphological architecture of the cells. Additionally, our findings suggest that MSI-1436 enhances the 2-NBDG internalization by increasing the expression of SIRT1, which is associated with liver insulin sensitivity, and promotes mitochondrial dynamics by modulating their number and morphotype through PINK1, MFN1, and MFN2 increased expression. Our study provides evidence that MSI-1436 has a positive impact on equine hepatic progenitor cells, indicating its potential therapeutic value in the treatment of EMS and insulin dysregulation.

The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

The purpose of this work is to determine the possibility of using an automated SkyWatcher Virtuoso system to analyze distribution of sky luminance. The article presents the procedure for measuring the sky luminance distribution defined according to CIE using a manual luminance meter cooperating with the SkyWatcher system. The use of matrix luminance meter was also analyzed.

Understanding the phenomena underlying the non-selective susceptibility to ischemia of py-ramidal neurons in the CA3 area of the hippocampus is important from the point of view of elu-cidating the mechanisms of memory loss and the development of post-ischemic dementia. We used an ischemic model of Alzheimer's disease to study changes in amyloid protein precursor gene expression, its cleavage enzymes and tau protein in the CA3 area of the hippocampus af-ter a 10-minute brain ischemia with 12, 18, and 24-month survival. Quantitative reverse tran-scriptase PCR assay showed that the expression of all the genes that contribute to amyloid pro-duction was dysregulated within 2 years in the CA3 area of the hippocampus after ischemia. The expression of the amyloid protein precursor gene was above the control values at all times of the study. The expression of the α-secretase gene also exceeded the control values throughout the study. In contrast, the expression of the β-secretase gene reaching its maximum increase 12 months after ischemia, was below control values after 18 months and again above control values after 24 months of survival. Presenilin 1 and 2 gene expression was significantly elevated throughout the follow-up period, with peak expression of both genes occurring 12 months after ischemia. This suggests that the genes studied are involved in the non-amyloidogenic processing of amyloid protein precursor. Also, tau protein gene expression was significantly elevated throughout the observation period, and peak gene expression was present 12 months after is-chemia. Data indicate that an episode of brain ischemia with long-term survival causes damage and death of pyramidal neurons in the CA3 area of the hippocampus in a manner dependent on modified tau protein. Thus defining a new and important mechanism of pyramidal neuronal death in the CA3 area after ischemia. In addition tau protein gene modification after brain is-chemia is useful in identifying ischemic mechanisms occurring in Alzheimer's disease.

Cardiovascular diseases (CVDs) constitute the first cause of death among the population of developing and developed countries. Atherosclerosis, which is a disorder with multifactorial etiopathogenesis, underlies most CVDs. The available literature includes ample research studies on the influence of classic cardiovascular (CV) risk factors. However, environmental exposure to heavy metals, among other substances, is still an unappreciated risk factor of CVDs. This study aimed to assess the concentration of some heavy metals (copper (Cu), zinc (Zn), manganese (Mn), cobalt (Co), and iron (Fe)) in the blood serum of postmyocardial infarction (post-MI) patients and patients free from myocardial infarction (MI) as well as estimate the relationship between the occurrence of MI and increased concentration of heavy metals. The concentration of heavy metals (Cu, Zn, Mn, Co, and Fe) was assessed using the inductively coupled plasma mass spectrometry technique in a group of 146 respondents divided into two groups: post-MI group (study group (SG), n = 74) and group without cardiovascular event (CVE) having a low CV risk (control group (CG), n = 72). The concentration of the analyzed heavy metals was higher in SG. All the heavy metals showed a significant diagnostic value (p < 0.001). The highest value of area under the curve (AUC) was observed for manganese (Mn) (0.955; 95% confidence interval (CI) = 0.922–0.988), while the lowest value was found for zinc (Zn) (0.691; 95% CI = 0.599–0.782). In one-dimensional models, high concentrations of each of the analyzed heavy metals significantly increased the chances of having MI from 7-fold (Cu) to 128-fold (Mn). All the models containing a particular metal showed a significant and high discrimination value for MI occurrence (AUC 0.72–0.92). Higher concentrations of Cu, Zn, Mn, Co, and Fe were found to considerably increase the chances of having MI. Considering the increasingly higher environmental exposure to heavy metals in recent times, their concentrations can be distinguished as a potential risk factor of CVDs.

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH3, and other gases (GHGs, O3 – sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO2-based photocatalyst. Treated gas airflow (0.25 to 0.76 m3/s) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to i) 63% of odor, ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p-cresol, and indole, respectively, iii) 14% of nitrous oxide (N2O), iv) 100% of O3, and 26% generation of CO2. Under UV-C (185+254 nm) photocatalysis, the percent reductions of target gases were up to i) 54% and 47% for p-cresol and indole, respectively, ii) 25% of N2O, iii) 71% of CH4, and 46% & 139% generation of CO2 & O3, respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns.

The main scope of the presented paper is an assessment of the potential repellent effect of selected essential oils (EOs) against Alphitobius diaperinus, which can cause economic losses in storages and poultry industry. Due to development of pesticide resistance in A. diaperinus populations, as well as an attempt to limit extensive usage of potentially harmful pesticides in food-related industries, there is a strong need for development of alternative methods of management of A. diaperinus infestations. Because of cost-effectiveness, availability and low vertebrate toxicity EOs are promising agents in pest management. In presented paper four of-the-shelf EOs: mint, vanilla, lemon and citronella (and their mixtures) were tested as a potential repellents. Moreover, novel preference assay providing an extended analysis of preference and the locomotor response was used. The most effective EOs were, respectively: citronella and lemon. EOs mixtures were generally more repellent than single EOs, with lemon and vanilla 1:1 mixture acting as the strongest repellent. Few of tested EOs caused significant alterations in locomotor activity, although direct relation wasn’t observed. In conclusion, EOs can be potentially used as a repellent agents in A. diaperinus management. Additionally, data on locomotor activity may lead to better design of pull-push strategies in pest management.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

Solving environmental odor issues can be confounded by many analytical, technological, and socioeconomic factors. Considerable know-how and technologies can fail to properly identify odorants responsible for the downwind nuisance odor and mitigate it for the affected citizenry. We propose enabling solutions to environmental odor issues by utilizing troubleshooting techniques developed for the food, beverage, and consumer products industries. We showed that the downwind odorant impact-priority ranking process can be definable and relatively simple. The initial challenge is the prioritization of environmental odor character from the perspective of the impacted citizenry downwind. In this research, we aim at summarizing three natural models of the rolling unmasking effect (RUE) and discuss them more systematically in the context of the proposed downwind environmental odor prioritization approach. Regardless of the size and reach of an odor source, a simplification of odor character and composition typically develops with downwind dilution. The extreme odor simplification-upon-dilution was demonstrated for two plant varieties, prairie verbena and Virginia pepperweed. Their downwind odor frontal boundaries were dominated by single, character-defining odorants; p-cresol-dominated ‘barnyard’ odor, and benzyl mercaptan-dominated ‘burnt match’ odor, respectively. The P.T. porcupine downwind odor frontal boundary was dominated by two potent, character-defining odorants: (1) ‘onion’/‘body odor’ odorant #1 and (2) ‘onion’/‘grilled’ odorant #2. In contrast with their downwind boundary simplicities, each odor source presented considerable compositional complexity and composite character difference near the source. The proposed RUE approach’s ultimate significance is the illustration of naturally occurring phenomena that explain why some environmental odors and their sources can be challenging to identify and mitigate using the analytical only approach (focused on compound identities and concentrations). These approaches rarely move beyond comprehensive lists of compounds being emitted by the source.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of analytes concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23-ga Car/PDMS assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 x 0.75 mm i.d. SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The developed model offers new insight into optimization of air and gas sampling using SPME.

Biochar application to the soil can improve soil quality and nutrient leaching loss. Recent studies have reported that surficial application of biochar to stored swine manure can reduce emissions of odorous compounds and reduce the volatilization loss of ammonia. Our working hypothesis was that the biochar-treated manure application to the soil would decrease nutrient leaching from manure and increase plant-available nutrients. The study objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and other major and minor nutrients. Three biochars (i) neutral pH red-oak (RO), (ii) highly alkaline autothermal corn (Zea mays) stover (HAP), and (iii) mild acidic Fe-treated autothermal corn stover (HAPE) were incubated with swine manure for a month. The biochar-manure mixture was applied in triplicate to soil columns with application rate determined by the P₂O₅-P content in manure or manure-biochar mixtures after the incubation. The ammonium (NH₄⁺), nitrate (NO₃^-), and reactive P concentrations in soil column leachates were recorded for eight leaching events. Soil properties and plant-available nutrients were compared between treatments and control manure & soil. Manure-(HAP&HAPE) biochar treatments significantly increased soil organic matter (OM) and increased soil total C, N, and improved soil bulk density. Concentrations of KCl-extractable NH₄⁺ and NO₃^- significantly increased in HAPE column leachates during this 4-week study and in the soil after the experiment. A significant reduction in soil Mehlich3 Cu was also observed for the manure-HAPE mixture compared with the control. Overall, the manure-biochar incubation enabled biochar to sorb nutrients from manure, and the subsequent manure-biochar mixture application to soil improved soil quality and plant nutrient availability in comparison to conventional manure application to soil. This proof-of-the-concept study suggests that biochars could be used to solve both environmental and agronomic challenges and further improve the sustainability of animal and crop production agriculture.

This study evaluated the use of filtration and UV-A photocatalysis for the reduction of particulate matter (PM) and airborne bacterial pathogens in swine barns. Two MERV filters (8 and 15) were used to mitigate PM concentrations measured at the PM 1, PM 2.5, respirable PM, and PM 10 ranges. Filtration was also used to generate different levels of airborne pathogens to be treated by UV-A. Results show that MERV 8 and 15 filters effectively reduced PM concentrations (96-98%) in air exhausted from a swine barn (p ranged from < 0.01 to 0.04). UV-A photocatalysis did not mitigate PM concentrations. UV-A photocatalysis treatment reduced measured colony-forming units (CFUs) by 15-95%. The CFU percent reduction was higher when airborne PM concentration was low. The numeric results suggested a real mitigation effect despite p-values that did not meet the usual statistical cut-off of <0.05 for significance due to the large variability of the CFU control samples. Normalization of measured airborne pathogen concentrations by smaller PM size range concentrations led to emerging significant treatment differences for CFUs. A significant decrease (~60% reduction; p < 0.03) in the concentration of viable airborne bacteria was shown for all PM below the 10-micron range.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the analysis as well as theoretical considerations concerning to design of gear size ranges. This analysis consists in decomposition of the designed artefact (a gear) according to the rule “from general to details view”. The basics of the object-oriented analysis were formulated. Furthermore, design phases and the objects related to theses phases were discussed. The following models have been considered: hierarchical model, entity-relationship model, data-flow model and object model. Analysis is additionally connected with interactions between particular design phases.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

Keywords: flow mediated skin fluorescence; FMSF technique; NADH fluorescence, microcirculation, flowmotion, reactive hyperemia response, RHR, hypoxia sensitivity, HS, normoxia oscillatory index, NOI

Public funding of land consolidation projects is an instrument of the Common Agricultural Policy of the European Union (CAP). The execution of systematic land consolidation programmes focused on optimising the spatial structure of agricultural areas presents a possibility to improve agricultural production conditions and maximise the efficiency of agriculture on a local, regional, national and international level. However, due to limited access to financial resources, it is necessary to delimit the priority areas for land consolidation. A contemporary practice based on the assessment of the social support percentage of potential land consolidation projects in individual villages does not represent a real necessity for action. This problem leads to ineffective utilisation of financial resources and reduces the efficiency of the implemented programmes. We proposed a new algorithm for assessing real needs for land consolidation based on a detailed multi-faceted analysis of the spatial structure of agricultural areas. The research method involved factors describing the spatial structure defectiveness of farms as well as those determining land quality in correspondence to investment’s profitability. Another factor verifying the potential economic rationale of land consolidation was transaction prices mostly reflecting the agricultural value of the land. The analysis showed that land consolidation in areas with defective spatial structure and a relatively high market value should be a priority. This approach will contribute to maximising profits by increasing the productivity of areas featuring the highest agricultural suitability.

Volatile fatty acids (VFAs) are a group of common metabolites with a potential of universal infochemicals dedicated to transferring of information between higher organisms and bacteria either from microbiome or external environment. VFAs are common substances among various insect orders, there are numerous studies exploring their influence on the behavior of different insect species. In relation to papers published by J. E. McFarlane, we assess the effects of formic, acetic, propionic, butyric, valeric acids on spatial preference of common stored food grain products, and poultry industry pest – lesser mealworm (Alphitobius diaperinus). We present novel method of continuous, simultaneous assessment of site preference as well as travelled distance in constant-flow olfactometer. All tested VFAs except valeric had a significant repellent effect with formic acid being effective in the lowest concentration. Additionally, VFAs significantly altered distance travelled by insects. Obtained results indicate a potential role of VFAs in the olfactory guided behavior of A. diaperinus, we speculate that reaction to the presence if VFAs may deviate form specificity of species’ original habitat.

The thermal decomposition of siderite and its decomposition products in a vacuum atmosphere was investigated for the first time using in situ high-temperature transmission Mössbauer spectroscopy. These measurements were supported by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, and magnetic measurements. In situ Mössbauer spectra were collected from room temperature (RT) to 750 oC with a temperature step of 50 oC. After that, the sample was cooled down to RT with step 100 oC. Raw siderite samples contain siderite as the only iron-bearing mineral, and after heating the samples at high temperatures, hematite and magnetite are only Fe-bearing phases. In the temperature range of 300 oC - 500 oC, siderite decomposition occurs. The analysis shows that siderite transforms directly into magnetite, and then hematite generation occurs as long as siderite is present in the sample. Changing hyperfine parameters like isomer shift, quadrupole splitting, or hyperfine magnetic field versus temperature were obtained for siderite and iron oxides (hematite, magnetite). The measurements also show that magnetite formed during the decomposition of siderite is a composition of particles of various sizes and a low degree of crystallization.

Recently, there has been a trend towards healthy food. Consumers are looking for products that have health-promoting properties in addition to their taste. Actinidia fruit, apart from being tasty, contains valuable nutrients. They are high in vitamin C, polyphenols, and pectins and low in calories. These pro-health properties allow kiwiberry fruit to qualify in the group of so-called superfoods. All tested cultivars belong to two species of Actinidia, well tolerating conditions of moderate climate with negative temperatures in winter. The cultivars differed significantly in mineral content, color, firmness, weight and content of antioxidant substances. Summer pruning (lightening) increased the content of N, P, K, extract, and NO3 and resulted in darker fruit color. However, it slightly decreased the content of polyphenols. 'Sientiabrskaja' can be recommended for consumption as the cultivar richest in polyphenols and with the highest health-promoting values.

Porcine reproductive and respiratory syndrome virus (PRRSV) infections cause significant economic losses to swine producers every year. Aerosols containing infectious PRRSV are an important route of transmission, and proper treatment of air could mitigate the airborne spread of the virus within and between barns. Previous bioaerosol studies focused on the microbiology of PRRSV aerosols; thus, the current study addressed the engineering aspects of virus aerosolization and collection. Specific objectives were to (1) build and test a virus aerosolization system, (2) achieve a uniform and repeatable aerosol generation and collection throughout all replicates, (3) identify and minimize sources of variation, (4) verify that the collection system (impingers) performed similarly. The system for virus aerosolization was built and tested (Obj. 1). The uniform airflow distribution was confirmed using a physical tracer (<12% relative standard deviation) for all treatments and sound engineering control of flow rates (Obj. 2). Theoretical uncertainty analyses and mass balance calculations showed <3% loss of air mass flow rate between the inlet and outlet (Obj. 3). A comparison of TCID₅₀ values among impinger fluids showed no statistical difference between any two of the three trials (p-value = 0.148, 0.357, 0.846) (Obj. 4). These results showed that the readiness of the system for research on virus aerosolization and treatment (e.g., by ultraviolet light), as well as its potential use for research on other types of airborne pathogens and their mitigation on a laboratory scale.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FR). Significant amounts of FR are usually required to effectively affect the polymer burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC) and pentaerythritol (PER) and its composites containing additionally short basalt fibers (BF). Composites manufactured by twin-screw extrusion were subjected to four reprocessing cycles by injection molding, comprehensively analyzing structural, mechanical, and fire behavior changes in each cycle. The obtained results confirmed the safety of using the proposed flame-retardant system for polyamide, processed under the recommended process parameters, without the risk of significant changes in the structure despite the partial increase in flammability caused mainly by the degradation of the polymer.

Hydrogen sulfide and ammonia are always a concern in the livestock industries, especially when farmers try to clear their manure storage pits. Agitation of manure can cause dangerously high concentrations of harmful agents such as H₂S and NH₃ to be emitted into the air. Biochar has the ability to sorb these gases. We hypothesized that applying biochar on top of manure can create an effective barrier to protect farmers and animals from exposure to NH₃ and H₂S. In this study, two kinds of biochar were tested, highly alkaline, and porous (HAP, pH 9.2) biochar made from corn stover and red oak biochar (RO, pH 7.5). Two scenarios of (6 mm) 0.25” and (12 mm) 0.5” thick layers of biochar treatments were topically applied to the manure and tested on a pilot-scale setup, simulating a deep pit storage. Each setup experienced 3-min of agitation using a transfer pump, and measurements of the concentrations of NH₃ and H₂S were taken in real-time and measured until the concentration stabilized after the sharp increase in concentration due to agitation. The results were compared with the control in the following 3 situations: 1. The maximum (peak) flux 2. Total emission from the start of agitation until the concentration stabilized, and 3. The total emission during the 3 min of agitation. For NH₃, 0.5” HAP biochar treatment significantly (p<0.05) reduced maximum flux by 63.3%, overall total emission by 70%, and total emissions during the 3-min agitation by 85.2%; 0.25” HAP biochar treatment significantly (p<0.05) reduced maximum flux by 75.7%, overall, total emission by 74.5%, and total emissions during the 3-min agitation by 77.8%. 0.5” RO biochar treatment significantly reduced max by 8.8%, overall total emission by 52.9%, and total emission during 3-min agitation by 56.8%; 0.25” RO biochar treatment significantly reduced max by 61.3%, overall total emission by 86.1%, and total emission during 3-min agitation by 62.7%. For H₂S, 0.5” HAP biochar treatment reduced the max by 42.5% (p=0.125), overall total emission by 17.9% (p=0.290), and significantly reduced the total emission during 3-min agitation by 70.4%; 0.25” HAP treatment reduced max by 60.6% (p=0.058), and significantly reduced overall and 3-min agitation’s total emission by 64.4% and 66.6%, respectively. 0.5” RO biochar treatment reduce the max flux by 23.6% (p=0.145), and significantly reduced overall and 3-min total emission by 39.3% and 62.4%, respectively; 0.25” RO treatment significantly reduced the max flux by 63%, overall total emission by 84.7%, and total emission during 3-min agitation by 67.4%.

The aim of the study was to verify whether a 20 and 40% reduction of nitrogen (N) fertilization rate will be sufficient to maintain soil basic chemical features, fertility, and yielding in monoculture maize cultivation in the no-tillage (NT) system versus the traditional plowing (PL) system. In addition, it was examined which tillage system (PL, NT) allows reduction of fertilization while maintaining good yields of the tested soils. Two fields (10 ha each) were established for PL and NT maize cultivation and soils (0-20 cm) were sampled two times per year - in spring (before maize sowing) and in autumn (after maize harvesting). A broad range of chemical and biological parameters (i.e. pH, forms of nitrogen, phosphorus and carbon, content of selected macronutrients and humic substances, respiration activity) were monitored during the experiment. It was evidenced that the 20% reduction in N fertilization does not have an adverse effect on the chemical and biological characteristics of soils. In turn, the maize yield was mainly the result of both the tillage system and the N rate, i.e. it was significantly higher in the PL system.

Maximal heart rate (HRmax) is a widely used measure of cardiorespiratory fitness. Prediction of HRmax is an alternative to cardiopulmonary exercise testing (CPET), but its accuracy among endurance athletes (EA) requires evaluation. This study aimed to externally validate HRmax prediction models in the EA independently for running and cycling CPET. 4043 runners (age=33.58 (8.12) years; 83.53% males; BMI=23.66 (2.54) kg·m−2) and 1026 cyclists (age=36.88 (9.03) years; 89.67% males; BMI=24.04 (2.65) kg·m−2) underwent maximum CPET. Student t-test, mean absolute percentage error (MAPE), mean absolute error (MAE), and root mean square error (RMSE) were applied to externally validate 8 running and 5 cycling HRmax equations. HRmax was 184.60 (9.79) beats·min−1 and 182.66 (10.28) beats·min−1 respectively for running and cycling, p=0.001. Measured and predicted HRmax differed significantly (p=0.001) for 9 of 13 (69.23%) models. HRmax was overestimated by 8 (61.54%) and underestimated by 5 (38.46%) formulae. Overestimated HRmax ranged 0.08-4.94 beats·min−1 and underestimated HRmax ranged 0.03-4.90 beats·min−1. MAE and RMSE were 0.18-4.94 beats·min−1 and 9.13-10.47, respectively. MAPE ranged 3.95-4.69%. Prediction models do not allow for accurate estimation of HRmax. HRmax was more often underestimated than overestimated. Predicted HRmax can be implemented for EA as a supplemental method but CPET is the preferable approach.

The aim of the study was to verify whether a reduced nitrogen (N) fertilization rate according to the EU recommendation (“From field to table” directive) may guarantee good yields and will be sufficient to maintain soil fertility in monoculture maize cultivation in the no-tillage (NT) system versus the traditional plowing (P) system. Two fields (10 ha each) were established for P and NT maize cultivation where the following N doses were applied: 0.0; 69.0, 92.0, and 115.0 kg ha-1. Soils (0-20 cm) were sampled two times per year - in spring (before maize sowing) and in autumn (after maize harvesting). A broad range of chemical (reaction, water holding capacity, total and easily degradable carbon, ammonium, nitrates, magnesium, calcium, potassium, sulfur) and biological (respiration, humic acids) parameters were monitored during the experiment. The vast majority of these factors had higher values in autumn than in spring. Although the role of reduced fertilization was not shown to be significant, the correlation analysis revealed some relationships between yield and nutrient availability. The 20% reduction in N fertilization does not have an adverse effect on the chemistry and biological characteristics of soils and does not worsen their chemical and biological quality.

Purpose: Surgical site infection (SSI) is a significant complication of non-reconstructive and reconstructive breast. This study aimed to assess SSI after breast surgery over 5 years in a single center in Poland. The microorganisms responsible for SSI and their antibiotic susceptibility were determined. Materials/methods: Data of 2129 patients acquired over 5 years postoperatively by the [center] were analyzed. Results: SSI was diagnosed in 132 patients (6.2%) and was an early infection in most cases (65.2%). The incidence of SSI was highest in patients who underwent subcutaneous amputation with simultaneous reconstruction using an artificial prosthesis (14.6%) and breast reconstruction via the TRAM flap method (14.3%). Gram-positive bacteria were responsible for SSI in most cases (72.1%), and these were mainly Staphylococcus strains (53.6%). These strains were 100% susceptible to all beta-lactam antibiotics (except penicillin), but were less susceptible to macrolides and lincosamides. Conclusions: SSI is a serious problem, and attention should be focused on its prevention. Reconstruction using an artificial prosthesis or via the TRAM flap method is connected to increased SSI incidence. Further studies are required to prevent SSI following breast surgery.

Tin (IV) oxide nanoparticles (SnO2 NPs) have received a lot of interest because of their interesting features. SnO2 NPs have proven productive in a range of fields, including water purification, supercapacitors, batteries, antibacterial and antioxidant agents, and others. SnO2-based nanoparticles found a wide range of applications after incorporating materials with varying chemical compositions. SnO2 NPs and their nanocomposites have been used effectively as antibacterial agents against various pathogenic bacteria, photocatalysts for dye degradation, and electrode materials for supercapacitors (SCs). This article covers the characteristics of SnO2 NPs, SnO2 nanocomposite materials, applications of SnO2 NPs and their composite materials, including antibacterial, energy storage, and photocatalysis, as well as some significant recent studies.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

The mutation in NF2 is the most common alteration associated with meningioma oncogenesis, and it is related to the loss of a suppressing protein called merlin. At the same time, alterations in energy production are visible in cancer cells where increased demand for energy is observed. Fatty acid oxidation could be one of the ways cancer cells obtain energy. This metabolic pathway uses the acylcarnitine shuttle system, which is responsible for the acylation of fatty acids and their transport through mitochondria. Therefore, this study aimed to profile acylcarnitines with short-, medium- and long-acyl chain length in meningiomas to assess their changes in tumors with different NF2 mutation statuses. For the analysis, solid-phase microextraction (SPME) coupled with liquid chromatography high resolution mass spectrometry (LC-HRMS) was used. The presented sampling method enables low invasive and easy collection of the analytes from the studied lesions, which can be crucial for future analysis of potential biomarkers in the surgery room. It was observed that higher levels of these analytes characterized meningiomas with NF2 mutation. Moreover, increased energy consumption and elevated levels of acylcarnitines show that these analytes can be considered as a marker of increased fatty acid oxidation in NF2 mutated cells.

A 36-year-old professional marathon runner reported sudden heart palpitations occurring during competitions, with heart rates (HR) of 230 bpm recorded on sports HR monitor (HRM) over 4 years. These episodes subsided upon the cessation of exercise. Electrocardiograms, echocardiography, and cardiac magnetic resonance imaging results were borderline for athlete's heart. Because an electrophysiology study and standard exercise tests provoked no arrhythmia, doctors suspected Munchhausen syndrome. Ultimately, an exercise test that simulated the physical effort during a competition provoked tachyarrhythmia consistent with the HRM readings. This case demonstrates the diagnostic difficulties related to exercise-induced arrhythmia and the diagnostic usefulness of sports HRMs.

Brain tumors are neoplasms with one of the highest mortality rates. Therefore, the availability of methods that allow the quick and effective diagnosis of brain tumors and selection of appropriate treatments is of critical importance for patient outcomes. In this study, coated blade spray-mass spectrometry (CBS-MS), which combines the features of microextraction and fast ionization methods, is applied for the analysis of brain tumors. In this approach, a sword-shaped probe is coated with a sorptive material to enable the extraction of analytes from biological samples. The analytes are then desorbed using only a few microliters of solvent, followed by the insertion of the CBS device into the interface on the mass spectrometer source. The results of this proof-of-concept experiment confirmed that CBS coupled to high-resolution mass spectrometry (HRMS) enables the rapid differentiation of two histologically different lesions: meningiomas and gliomas. Moreover, quantitative CBS-HRMS/MS analysis of carnitine, the endogenous compound, previously identified as discriminating metabolite showed good reproducibility with the variation below 10% when using a standard addition calibration strategy and deuterated internal standards for correction. The resultant data show that the proposed CBS-MS technique can be useful for on-site qualitative and quantitative assessments of brain tumor metabolite profiles.

The main aim of this study is to investigate the optimization of the technological process for selective laser melting (SLM) additive manufacturing. The group of process parameters considered was selected from the first-stage parameters identified in preliminary research. Samples manufactured using three different sets of parameter values were subjected to static tensile and compression tests. The samples were also subjected to dynamic Split–Hopkinson tests. To verify the microstructural changes after the dynamic tests, microstructural analyses were conducted. Additionally, the element deformation during the tensile tests was analyzed using digital image correlation (DIC). To analyze the influence of the selected parameters and verify the layered structure of the manufactured elements, sclerometer scratch hardness tests were carried out on each sample. Basing on the research results it was possible to observe the porosity growth mechanism and its influence on the material strength (including static and dynamic tests). Parameters modifications that caused 20% lower energy density, elongation of the elements during tensile testing decreased twice, which was strictly connected with porosity growth. An increase of energy density by almost three times caused a significant reduction of force fluctuations differences between both tested surfaces (parallel and perpendicular to the building platform) during sclerometer hardness testing. That kind of phenomenon had been taken into account in the microstructure investigations before and after dynamic testing where it had been spotted a positive impact on material deformations based on fused material grains formation after SLM processing.