Mobile elevating work platforms (MEWPs) consist of a work platform, extending structure, and chassis, and are used to move persons to working positions. MEWPs are useful but are composed of pieces of equipment, and accidents do occur owing to equipment defects. Among these defects, accidents caused by the fracture of bolts fixed to the extension structure and swing system are increasing. This paper presents a failure analysis of the fixing bolts of MEWP. Standard procedure for failure analysis was employed in this investigation. Visual inspection, chemical analysis, tensile strength measurement, and finite element analysis (FEA) were used to analyze the failure of the fixing bolts. Using this failure analysis approach, we found the root cause of failure and proposed a means for solving this type of failure in the future. First, the chemical composition of the fixing bolt is obtained by a spectroscopy chemical analysis method, which determined that the chemical composition matched the required standard. The tensile test showed that the tensile and yield strengths were within the required capacity. The stress analysis was carried out at five different boom angles, and it was determined that the fixing bolt of MEWP can withstand the loads at all the boom angles. The outcomes of the fatigue analysis revealed that the fixing bolt fails before reaching the design requirements. The results of the fatigue analysis showed primarily that the failure of the fixing bolt was due to fatigue. A visual inspection of the fractured section of the fixing bolt also confirmed the fatigue failure. We propose a method to prevent failure of the fixing bolt of the MEWP from four different standpoints: the manufacturer, safety certification authority, safety inspection agency, and owner.

This work investigates the stability conditions for linear systems with time-varying delays via augmented Lyapunov-Krasovskii functional(LKF). Two types of augmented LKFs with cross terms in integral are suggested to improve the stability conditions for interval time-varying linear systems. Through this work, the compositions of the LKFs are considered to enhance the feasible region of stability criterion for linear systems. Mathematical tools such as Wirtinger-based integral inequality(WBII), zero equalities, reciprocally convex approach, and Finsler’s lemma are utilized to solve the problem of stability criteria. Two sufficient conditions are derived to guarantee the asymptotic stability of the systems using linear matrix inequality(LMI). First, asymptotic stability criteria are induced by constructing the new augmented LKFs in Theorem 1. And then simplified LKFs in Corollary 1 are proposed to show the effectiveness of Theorem 1. Second, asymmetric LKFs are shown to reduce the conservatism and the number of decision variables in Theorem 2. Finally, the advantages of the proposed criteria are verified by comparing maximum delay bounds in two examples. Two numerical examples show that the proposed Theorem 1 and 2 obtained less conservative results than existing outcomes. Also, Example 2 shows that the asymmetric LKF methods of Theorem 2 can provide larger delay bounds and fewer decision variables than Theorem 1’s in some specific systems.

The phenolics concentrations of rapeseed are important because they are antinutritional com-pound or directly positive related to antioxidant actives. In this study, single nucleotide poly-morphisms (SNPs) identified from genotyping-by-sequencing (GBS), and genome-wide associa-tion study of phenolic contents were investigated in 95 rapeseed mutant lines derived from gamma rays and their original cultivar. A total of 3,196,318 SNPs were detected, identifying a set of 70,208 union SNPs used to perform association studies. Six phenolics and glucosinolate (pro-goitrin) were identified, sinapine was the major phenolic compound (91.2–99.2%) in all geno-types. The association study was conducted for six phenolic compounds, progoitrin, total sinap-ine content (TSC), total phenolic content (TPC) and seed yield. The association study identified 241 SNPs that were significantly associated with six phenolic compounds, progoitrin, TSC and TPC. Based on the detected SNP markers, BnaA06g31740D, a gene associated progoitrin, BnaC-nng39930D, a gene associated trans-sinapine 1, BnaA07g31720D, a gene associated trans-sinapine 2, BnaC03g31950D and BnaA06g09180D, a gene associated TSC, and BnaAnng27700D, a gene associ-ated TPC, were selected as candidate genes. The SNP makers associated major phenolic com-pounds identified and could be used as targets for breeding programs aimed at improving anti-oxidant contents and reducing antinutritional components.

Fresh-cut apple is commonly known as minimally processed agriculture products because of their convenience and ease of consumption. However, during storage, the quality of the apple rapidly changes after the cutting process due to enzymatic and non-enzymatic processes. This study aimed to monitor the quality changes of fresh-cut apples at various temperatures and different types of products in the application of a cold chain system during distribution and storage. The results showed that the total viable count in fresh-cut apples initially differed between apple only and mixed products (apple, orange, and tomato) during storage (p < 0.05). Moreover, there are no significant differences (p > 0.05) in physicochemicals except firmness, titratable acidity, and pH, which are highly correlated to microbial growth (total viable count and total coliform number). Furthermore, the optimal temperature for extending the shelf-life of fresh-cut apples was at 4°C.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

Background: Patients undergoing dual antiplatelet therapy (DAPT) may experience recurrent gastrointestinal bleeding (GIB). We investigated the clinical characteristics and risk factors for recurrent non-variceal upper gastrointestinal bleeding (NVUGIB) in patients who had experienced NVUGIB during receiving DAPT. Methods: We enrolled patients diagnosed with NVUGIB during receiving DAPT between 2006 and 2020. Definite bleeding was confirmed by esophagogastroduodenoscopy in all NVUGIB patients. Results: A total of 124 patients were diagnosed with NVUGIB during receiving DAPT. Male was predominant (n = 103, 83.1%), bleeding mostly from the stomach (n = 94, 75.8%) and peptic ulcers (n = 72, 58.1%). After successful hemostasis of NVUGIB, 36 patients (29.0%) experienced at least one episode of recurrent upper GIB, 19 patients (15.3%) died, and 7 (5.6%) patients had a bleeding-related death. Multivariate analysis showed that age was a significant factor for re-bleeding (odds ratio [OR],1.050; 95% confidence interval [CI]:1.001-1.102, P-value:0.047), all-cause mortality (OR,1.096; 95% CI:1.020-1.178, P=0.013), and re-bleeding related mortality (OR,1.187; 95% CI:1.032-1.364, P-value:0.016). In Kaplan-Meier analysis, the cumulative probabilities of re-bleeding, death, and bleeding-related death were significantly higher in patients aged 70 and older (P=0.008, <0.001, and 0.009, respectively). Conclusion: Clinicians should be cautious about re-bleeding and mortality when elderly patients who experienced NVUGIB during receiving DAPT.Keywords: dual antiplatelet therapy; upper gastrointestinal tract; bleeding; mortality

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

There is a lack of data comparing sugammadex with anticholinesterase for the quality of anaesthesia recovery, especially following a single bolus dose of rocuronium. Thus, we evaluated the influence of reversal with sugammadex or neostigmine on post-operative quality of recovery by using the Post-operative Quality Recovery Scale (PQRS). A total of 86 patients undergoing trans-pars plana vitrectomy (TPPV) under general anaesthesia were intubated following a single bolus dose of rocuronium (0.6 mg/kg). At the end of surgery, patients were received either neostigmine or sugammadex. The quality of recovery was assessed using the PQRS at 15 minutes and 40 minutes after surgery, and on post-operative day 1. The recovery rate in the physiological domain was higher in the sugammadex group at 15 minutes after surgery (P = 0.02). Though there were no significant differences in the overall cognitive recovery domain, patients in the sugammadex group could recall more numbers in reverse order. However, there were no significant differences between the groups in the other domains of the PQRS. The use of sugammadex may increase the quality of the post-operative physiological recovery at early post-operative periods compared with neostigmine use following a single bolus dose of rocuronium in patients undergoing TPPV with general anaesthesia.

In this paper, feasibility of the initial alignment of the gyro-free inertial navigation system (GF-INS) is investigated. Initial roll and initial pitch are obtained as the conventional INS since centripetal acceleration is very small. Relation between initial heading and accelerometers’ outputs of the gyro-free inertial measurement unit (GF-IMU) is derived. It is determined from the relation whether initial heading can be obtained in 15 GF-IMUs which have been presented in research literatures. The relationship between the accelerometer errors of GF-IMU and the initial heading error is derived. When gyros are additionally attached in one axis or two axes of the body frame, it is investigated that initial heading can be obtained. The initial heading error is also calculated from the accelerometer errors and the gyroscope errors. The results show that the initial heading from only accelerometer outputs of the GF-IMU cannot be used in the GF-INS since the error is too large. It can also be seen from the results that the initial heading can be used in the GF-INS if two gyroscopes are additionally attached to the roll and pitch axes of the body frame.

The global shrimp farming industry is impacted by various infectious diseases, leading to marked production losses. Virulent Vibrio parahaemolyticus strains (VPAHPND) and other Vibrio species cause acute hepatopancreatic necrosis disease (AHPND) in shrimp. We isolated a binary toxin PirA/B-bearing V. campbellii strain (HJ-2023) from a Korean shrimp farm. The biochemical characteristics and antibiotic susceptibility of HJ-2023 were analyzed and compared to those of PirA/B-bearing VPAHPND. Non-AHPND-causing V. campbellii was the control. The pathogenicity of each strain was analyzed in white-leg shrimp. Phylogenetic analysis classified the isolated HJ-2023 strain as V. campbellii. Biochemical tests confirmed distinct properties of HJ-2023, compared to the genetically similar V. harveyi group. The AHPND-causing toxin gene of HJ-2023 showed 100% similarity to the rpoD gene of VCAHPND. An antibiotic disc susceptibility test indicated that HJ-2023 showed resistance to ampicillin, clindamycin, lincomycin, and erythromycin, which is effective against gram-positive bacteria, and showed weak sensitivity to gentamycin. Furthermore, HJ-2023 was 25% less toxic than VPAHPND but could be lethal during aquaculture-related outbreaks. These results highlight the complexity and virulence of AHPND-causing strains through multiple pathways and confirm the pathogenicity of V. campbellii, which increases the risk posed by AHPND to shrimp aquaculture. Our findings could help prevent AHPND.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

Roses are one of the most important floricultural crops, and their essential oils have long been used for cosmetics and aromatherapy. We investigated the volatile compound compositions of 12 flower-color mutant variants and their original cultivars. Twelve rose mutant genotypes were developed by treatment with 70 Gy of 60Co gamma irradiation of six commercial rose cultivars. Essential oils from the flowers of the 18 genotypes were analyzed by gas chromatography–mass spectrometry. Seventy-seven volatile compounds were detected, which were categorized into five classes: hydrocarbons, terpenoids, alcohols, esters, and others. Hydrocarbons, alcohols, and esters were major components in all rose flowers. The mutant genotypes CR-S8 and CR-S9 showed higher contents of hydrocarbons than the original cultivar. In addition, CR-S1, CR-S3, and CR-S4 mutant genotypes showed higher ester contents than their original cultivar. Nonacosane, 2-methylhexacosane, and 2-methyltricosane were major volatile compounds among all genotypes. Hierarchical cluster analysis of the rose genotypes gave four groups according to grouping among the 77 volatile compounds. These findings will be useful for the selection of rose genotypes with improved volatile compounds.

In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation as that expressed in terms of total motions where the base shear force is applied for earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

The sensitivity of DNBR(Departure from Nucleate Boiling Ratio) values to approaches of subchannel control volume selection has been investigated for the TS01 and TS03 out of HIPER17 CHF(Critical Heat Flux) tests. In general, the coolant-centered subchannel method is applied to subchanel analyses for fuel bundle. When it comes to predicting for CHF of high quality region, however, the rod-centered subchannel method was better over high quality region. As a result, the rod-centered subchannel method were more suitable at a conservative point of view than the coolant-centered subchannel method comparing major properties. Also, it was confirmed that the radial subchannel locations at the minimum DNBR were similar when comparing both analysis results by two kind of methods.

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

This study aims to investigate the effects of chest mobilization and breathing exercises on respiratory function, trunk stability, and endurance in chronic stroke patients who have contracted coronavirus disease (COVID-19). Thirty inpatients of a tertiary hospital in South Korea, who had a history of COVID-19 and were diagnosed with stroke within the last 6 months were randomly assigned to either the Chest Mobilization Exercise with Breathing Exercise (CMEBE) or Conservative Physical Therapy with Breathing Exercise (CPTBE) groups. The respiratory function, trunk stability, and endurance were measured at baseline and 6 weeks after the interventions. Both CMEBE and CPTBE groups showed improvements in respiratory function, trunk stability, and endurance after the intervention (p<0.05). However, the CMEBE group showed significantly greater improvements in forced expiratory volume in 1 second (p<0.05), trunk stability (p<0.05), and endurance (p<0.05) than the CPTBE group. No significant intergroup difference was observed in forced vital capacity and peak expiratory flow. Conclusion: The combination of chest mobilization and breathing exercises improved respiratory muscle mobility and endurance, stabilized the trunk, and enhanced balance and transfer of weight. The findings suggest that this intervention could be beneficial in improving respiratory function and endurance in stroke patients.

Safety and the apprehension of crime persist as significant concerns in both urban and rural locales. Crime Prevention Through Environmental Design (CPTED) guidelines, an architectural approach to crime deterrence, mitigate the likelihood of criminal activity by implementing strategic defensive design plans, particularly through effective lighting schemes within urban settings, thereby alleviating fear of crime. This comprehensive set of principles serves to enhance overall quality of life. Additionally, within the realm of environmental crime prevention, enhanced street lighting has been identified as a crucial factor in diminishing both actual crime rates and the perceived risk of criminal activity in built environments. While current recommendations advocate for the installation of lighting in poorly lit areas for safety reasons, evaluating visibility solely based on the presence of existing streetlights proves insufficient for analyzing road surface luminance comprehensively. Thus, this study proposes establishing standardized illumination levels specifically tailored for facial recognition of potential criminal offenders. Furthermore, we advocate for defining specific thresholds for color temperature and colorimetric criteria to aid in distinguishing characteristics of individuals' attire. To analyze photometric safety and crime frequency in Seoul, Korea, new primary evaluation indicators were developed, including the Brightness index, Informatization index, and Safety index. By incorporating quantitative data into lighting design strategies, particularly within the framework of CPTED, there exists the potential to mitigate fear of crime during nighttime hours. These strategies facilitate the creation of well-lit environments conducive to the swift recognition and identification of potential perpetrators, thereby presenting a proactive approach to crime prevention. Consequently, this study introduces quantitative lighting standards to augment the efficacy of CPTED guidelines, ultimately contributing to the reduction of crime incidence.

The purpose of this study is to analyze the causes of cost variation in natural disaster prevention projects (NDPP) in Gyeongsangbuk-do and to develop effective cost and risk management strategies. The study collected data by conducting an online survey of 244 stakeholders. Binary logistic regression was used to analyze the impact of various variables on cost deviation, in-cluding project management risk (PMR), project costing and execution risk (PCER), project exe-cution strategy risk (PESR), construction project risk (CPR), project cost and schedule risk (PCSR), project management challenges (PMC), and construction project subcontractor and safety man-agement (CPSSM). The results showed that PMR (OR=3.744, 95% C.I. [1.657, 8.457]), PCER (OR=5.068, 95% C.I. [2.236, 11.484]), PESR (OR=3.447, 95% C.I. [1. 853, 6.413]), CPR (OR=2.292, 95% C.I. [1.020, 5.151]), PCSR (OR=4.817, 95% C.I. [2.250, 10.317]), PMC (OR=2.954, 95% C.I. [1.452, 6. 013]), and CPSSM (OR=2.419, 95% C.I. [1.297, 4.515]) had statistically significant effects on cost deviation. In particular, PMR, PCER, and PESR were identified as the main causes, and the effects of additional factors such as CPSSM were also important. The developed predictive model plays an important role in helping stakeholders of NDPP to manage risks in advance and take appro-priate preventive measures to ensure the success of the project. This study empirically supports the theoretical hypotheses of previous studies and provides a clear understanding of the causes of cost deviation in NDPP, which provides important insights for strategic decision-making and provides a new perspective on risk management.

The 2020 revision of South Korea’s Personal Information Protection Act (PIPA) updated procedures for the use of medical data for research. The PIPA provision allowing “pseudonymized information” to be used without the consent of the data subject for scientific research introduced ambiguity regarding the applicability of the PIPA versus the Bioethics and Safety Act (BSA), which allows “anonymized information” to be used for research only after data-subject consent and IRB approval for human-subject research are obtained. The main points requiring clarification include the distinction between “human-subject” and “scientific” research, the definition of anonymization and pseudonymization, the requirements for data-subject consent, and the procedures for institutional review boards (IRBs) and data review boards (DRBs). After reviewing the legal concepts and processes, this article recommends clarification of the guidelines for the use of medical data in research by distinguishing the concept and, in the long run, categorizing medical data based on the degree of risk.

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

For the elimination of radio-frequency interference (RFI) in a passive microwave radiometer, the threshold level is generally calculated from the mean value and standard deviation. However, a serious problem that can arise is an error in the retrieved brightness temperature from a higher threshold level owing to the presence of RFI. In this paper, we propose a method to detect and mitigate RFI contamination using the threshold level from statistical criteria based on a spectrogram technique. Mean and skewness spectrograms are created from a brightness temperature spectrogram by shifting the 2-D window to discriminate the form of the symmetric distribution as a natural thermal emission signal. From the remaining bins of the mean spectrogram eliminated by RFI-flagged bins in the skewness spectrogram for data captured at 0.1-s intervals, two distribution sides are identically created from the left side of the distribution by changing the standard position of the distribution. Simultaneously, kurtosis calculations from these bins for each symmetric distribution are repeatedly performed to determine the retrieved brightness temperature corresponding to the closest kurtosis value of three. The performance is evaluated using experimental data, and the error in the retrieved brightness temperature is observed to be less than approximately 3 K from a window with a size of 100 × 100 time-frequency bins according to the RFI levels and cases.

Background and Objectives: Although there has been growing interest in the association of ADHD with anxiety, depression, suicidal ideation, and self-esteem, there is a lack of consistent results and these associations remain unclear. This study investigated the differential patterns of anxiety, depression, suicidal ideation, and self-esteem with regard to the presence of ADHD. Materials and Methods: The subjects were divided into a patient group and a control group. The patient group included 49 patients diagnosed with ADHD at the department of psychiatry of one university hospital. For the control group, 3,727 students were invited to complete a questionnaire. Of the 1,717 students who responded to the questionnaire, 245 were selected for patient-controlled studies. All the subjects were instructed to complete the Beck Suicide Ideation Scale, Children's Depression Inventory, Beck’s Depression Inventory, State-Trait Anxiety Inventory, and Rosenberg Self-Esteem Scale. Results: ADHD subjects experienced more anxiety, depression, and suicidal ideation as well as lower self-esteem compared to the control group comprising participants without ADHD. Conclusions: These findings suggest that ADHD symptoms may contribute to greater suicidal ideation through experienced depression, anxiety, and low self-esteem in school-aged children. Therefore, appropriate ADHD symptom management is necessary to reduce suicidal ideation among school-aged children with ADHD symptoms.

Background: Idiopathic pulmonary fibrosis (IPF) is a progressive fibrotic lung disease with a poor prognosis. Pirfenidone is approved and widely used for the treatment of IPF and reduces lung function decline. The aim of this study was to evaluate the efficacy of different doses of pirfenidone for the prevention of disease progression in patients with IPF. Methods: This was a prospective, observational, single-center cohort study conducted in Haeundae Paik Hospital, Republic of Korea, from April 2021 to March 2023. IPF patients were assigned to three groups according to the dose of pirfenidone (600mg, 1,200mg, 1,800mg). The primary endpoint was the efficacy of pirfenidone according to dose for the prevention of disease progression over 12 months. The secondary endpoint was the role of Krebs von den Lungen-6 (KL-6) in predicting disease progression. Results: A total of 44 patients were enrolled, of whom 39 completed the study, with 13 patients assigned to each of the three groups. The median age was 71.7 years, and 79.5% of patients were men. The baseline characteristics were similar across groups, except the 600mg group was older (75.9 vs. 69.2 vs. 68.2 years, p = 0.016). Fourteen patients (35.9%) suffered disease progression. The rate of disease progression did not differ according to the dose of pirfenidone (38.5 vs. 38.5 vs. 30.8%, p = 1.000). In multivariable logistic regression analysis, KL-6 was not a statistically significant predictor of disease progression. Conclusions: In our study, regardless of dose, consistent pirfenidone use for 12 months resulted in similar efficacy for the prevention of disease progression in patients with IPF. Large-scale, randomized, double-blind, placebo-controlled clinical trials are needed.

This study focused on the development and implementation of an educational simulation program based on Korean Triage and Acuity Scale (KTAS) for nurses in emergency medical centers who completed KTAS training. We also examined its educational effects based on the evaluation of clinical decision-making ability, job satisfaction, and customer orientation. The study participants were 30 nurses in the emergency medical center of a general hospital. Data were collected from May 3 to 24, 2017, and analyzed using SPSS 22.0. There was a significant difference in the mean scores in clinical decision-making ability, job satisfaction, and customer orientation before and after simulation education. In other words, emergency nurses who received KTAS-based simulation education program improved their clinical decision making ability, job satisfaction, and customer orientation. Based on the results of this study, it is expected that it can be used for KTAS education, and it was found that simulation-based education is a useful learning method for triage nurses in emergency medical center.

To identify gender- and age-related associations between adult dental checkups and unmet dental care needs, we analyzed data of 14,000 participants, ages ≥ 19, from the 7th Korea National Health and Nutrition Examination Survey (2016–2018) (KNHANES VII). Data was collected via self-report questionnaires and interviews. Complex sample chi-square test and multiple logistic regression analysis indicated 31.7% of participants had unmet dental care needs; in the prior 12months, 67.1% had not utilized dental services, and 43.3% had not received dental checkups. Odds ratios (ORs) for dental checkups and unmet dental needs were 8.87 (CI:7.80–10.09, p < 0.001) for those who used dental services and 1.28 (CI: 1.13–1.44, p < 0.001) for those who had not. Significant age-dependent associations between those not receiving dental checkups and the rate of unmet dental care include men and women aged 50–59 years (OR: 1.77; CI = 1.22–2.58 and OR: 1.43; CI: 1.02–2.02; p = 0.040, respectively) and women ≥ 70 years (OR = 1.79, CI = 1.20–2.66, p = 0.004). Reducing unmet dental care needs requires greater public health promotion and education regarding regular dental checkups; additional practical strategies could enhance dental checkup compliance.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

The frame construction of an apartment complex that consists of multiple buildings encounters various uncertainties, owing to the complex relationships among units of work. Currently, the period of such a construction is calculated based on the number of floors of the highest building in the complex. This study quantitatively analyzes an apartment frame construction period using a queue model and evaluates the validity of the estimated period. In this regard, a methodology is proposed for analyzing the construction period by applying the concept of a customer and a server. A case study on the duration of an apartment frame construction is conducted with Korea Land and Housing Corporation, which has supplied the largest number of apartments in South Korea. It was found that the stable state of a queue system was observed when the rate of server utilization was applied to the basement and aboveground floors. However, a stable state was not reached on the ground floor. This study includes non-working days in its calculation and quantitatively analyzes uncertainty factors during construction. Therefore, the findings can be practically utilized to quantitatively plan the durations of work units in an apartment frame construction.

Liver receptor homolog-1 (LRH-1) has emerged as a regulator of hepatic glucose, bile acid, and mitochondrial metabolism. However, the functional mechanism underlying the effect of LRH-1 on lipid mobilization has not been addressed. This study investigated the regulatory function of LRH-1 in lipid metabolism during fasting. The wild-type (WT) and LRH-1 liver-specific knockout (LKO) mice were either fed or fasted for 24 h, and the liver and serum were isolated. During fasting, the LRH-1 LKO mice showed greater accumulation of triglycerides in the liver compared to that in WT mice. Interestingly, LRH-1 LKO liver decreased the perilipin 5 (PLIN5) expression and genes involved in β-oxidation. Additionally, the LRH-1 agonist dialauroylphosphatidylcholine also enhanced PLIN5 expression in human cultured HepG2 cells. To identify new target genes of LRH-1, these findings directed to analyze the PLIN5 promoter sequence, which revealed −1620/−1614 to be a putative binding site for LRH-1. This was confirmed by promoter activity and chromatin immuno-precipitation assays. Moreover, fasted WT primary hepatocytes showed increased co-localization of PLIN5 in lipid droplets (LDs) compared to that in fasted LRH-1 LKO primary hepatocytes. Overall, these findings suggest that PLIN5 might be a novel target of LRH-1 to mobilize LDs and manage the cellular needs.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Identifying the primary site of origin of metastatic cancer is vital for guiding treatment decisions, especially for patients with cancer of unknown primary (CUP). Despite advanced diagnostic techniques, CUP remains difficult to pinpoint and is responsible for a considerable number of cancer-related fatalities. Understanding its origin is crucial for effective management and potentially improving patient outcomes. This study introduces a machine learning framework ONCOfind-AI that leverages transcriptome-based gene set features to enhance the accuracy of predicting the origin of metastatic cancers. By ensuring compatibility between RNA-sequencing and micro-array data, we were able to construct a more comprehensive training dataset. Integrating data from different platforms improved the accuracy of our machine learning models for predicting cancer origins. Our method was validated using external data from clinical samples collected through Kangbuk Samsung Medical Center and the Gene Expression Omnibus. The external validation results demonstrated a top-1 accuracy ranging from 0.80 to 0.86, with a top-2 accuracy of 0.90. This study highlights that incorporating biological knowledge through curated gene sets can merge gene expression data from different platforms, enhancing the compatibility needed for more effective machine learning prediction models.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Recently, e-commerce companies have been adopting and continuously enhancing personalized product recommendation systems, and there is active research in this field within academia. However, personalized product recommendations in offline retail stores have not yielded significant outcomes thus far. Especially for small-format offline retail businesses like convenience stores, where customer information might be limited, providing personalized product recommendations poses even greater challenges. To address this issue, this study aimed to find a solution by shifting the perspective on recommendation methods and altering the target of recommendations in existing personalized recommendation models. In this study, recommending products that customers need in an offline store was defined as suggesting products that should be introduced and displayed within the store. In other words, the recommendation focus shifted from individuals to the stores themselves. This recommendation system proposes products that individual stores have not yet introduced but are anticipated to be purchased by customers among the products managed by the headquarters. Building upon this, we devised a store-based product recommendation system. The widely used user-based collaborative filtering model, a common technique in existing recommendation systems, was adapted into a store-based collaborative filtering model. Furthermore, various rules and logic pertinent to store operations and business considerations for convenience stores were integrated to implement this store product recommendation system. The accuracy and effectiveness of the system were demonstrated through its application in actual convenience stores. Results from the pilot implementation of the system showed that 88% of the newly recommended products in individual stores were sold based on one week of sales data, and the sales revenue was 1.75 times higher than the average sales revenue of those products across the entire company. Survey results on business owners' satisfaction yielded a score of 4.2 out of 5, indicating a high level of contentment. Additional observed effects included the expansion of product range and reduction in order lead times. However, 12% of the total recommended SKUs did not sell within one week, and 34% of the SKUs did not meet the overall average sales quantity. This research holds significance in extending the scope of personalized recommendation studies from primarily online platforms to offline retail businesses like convenience stores. It provides tangible methodologies and outcomes that can be implemented in real-world settings through the construction and validation of an actual system. The study also suggests avenues for future research to address some of the identified limitations.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

In this study, ozone oxidation experiment was carried out for the removal of fluorescent whitening agent which is widely used in textile dyeing and paper industry. The stilbene fluorescent whitening agent has been industrialized since the earliest, and the amount of current production is the highest. Due to the characteristics of the fluorescent whitening agent that cannot be removed by conventional wastewater treatment methods, the fluorescent whitening agent in wastewater treatment has difficulty in using as recycled water in the process. Pre-treatment ozone oxidation experiment was conducted prior to the introduction of Membrane Bio Reactor (MBR) treatment process by converting biodegradable materials into biodegradable materials. The removal efficiencies of fluorescent whitening agents, a diaminostilbene disulfonic acid derivative by ozone oxidation were evaluated by UV254 Scan, COD, T-N and color using a synthetic wastewater sample (COD=433.0 mg/ℓ) and paper and paper mill wastewater (COD=157.2 mg/ℓ).

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

Toward the standardization of O. biennis sprout extract (OBS-E), we aimed to obtain indicator compounds, using a validated method. HPLC-UVD allowed simultaneous quantification of indicator compounds quercetin 3-glucuronide and ellagic acid. The method was validated in terms of specificity, linearity, precision, accuracy, and limit of detection/limit of quantification (LOD/LOQ). High specificity and linearity was demonstrated, with correlation coefficients of 1.0000 for quercetin 3-glucuronide and 0.9998 for ellagic acid. The LOD/LOQ values were 0.486/1.472 μg/mL for quercetin 3-glucuronide and 1.003/3.039 μg/mL for ellagic acid. Intra-day and inter-day variability tests produced relative standard deviation for each compound of &lt;2%, a generally accepted precision criterion. High recovery rate were also obtained, indicating accuracy validation. The OBS-E prepared using various concentrations of ethanol were then analyzed. The 50% ethanol extract had highest content of quercetin 3-glucuronide, whereas the 70% ethanol extract possessed the lowest. However, the ellagic acid content was highest in the 70% ethanol extract and lowest in the 90% ethanol extract. Thus, quercetin 3-glucuronide and ellagic acid can be used industrially as indicator compounds for O. biennis sprout products, and our validated method can be used to establish indicator compounds for other natural products.

A Micro holes in a diamond are presented by using a homemade femtosecond (fs) Yb:KGW laser. An fs laser source was used emitting pulse duration of 230 fs at 1030 nm wavelength, whereas the spot size amounted to 8.9 μm. Parameters like pulse energy, and pulse number were varied over a wide range in order to evaluate their influence both on the micro hole geometry like hole diameter, circularity, taper angle, and on the drilling quality. Hourglass-shaped micro holes whose diameters decrease and increase again after a certain depth have important applications. The results demonstrate the feasibility of extending the drilling of an hourglass-shaped hole in a diamond sample, which has similar diameters at the hole entrance (92 μm) and exit (95 μm), but a much smaller diameter (28 μm) at a certain waist section inside the hole.

Three species of subfamily Cultrinae currently live in Korea, but Erythroculter erythropterus has been introduced into the Nakdonggang River and has taken over the habitat, reducing the habitat of Culter brevicauda. Only the endangered species C. brevicauda still lives in the Yeongsangang River, and it is necessary to be careful not to introduce E. erythropterus in the future. And Hemiculter eigenmanni is also found throughout the country. In order to effectively manage and conserve the species in its various habitats and against invasions, this study was initiated. The ultrastructure of the egg envelopes of three species of Cultrinae— E. erythropterus, C. brevicauda, and H. eigenmanni, inhabiting the Geumgang and Yeongsangang Rivers were observed. It was found that the zona radiata of the egg envelopes of all three species were divided into two layers–an outer and inner layer, with the outer surface having a non-structural form. This form is characteristic of fishes with muddy, stagnant habitats or spawning grounds. The number of pore canals on the surface of the egg envelopes was 83 for E. erythropterus, 75 for C. brevicauda, and 58 for H. eigenmanni per 10 ㎛2, and the thickness was 7.89±0.34 ㎛, 12.27±0.46 ㎛, and 7.42±0.24 ㎛, respectively. The shape of the micropyle demonstrated a funnel shape narrowing toward the inner diameter in all three species, and the size of the inner diameter was 6.62±0.29 (6.09~7.10) ㎛ in E. erythropterus, 4.19±0.39 (3.39~4.58) ㎛in C. brevicauda, and 3.98±0.46 (3.47~4.93) ㎛in H. eigenmanni. The differences between species were identified in the number of pore canals, thickness, and micropyle inner diameter of egg envelopes, which were species-specific. Our study revealed a morphological mechanism in the egg envelope that prevents the formation of interspecific hybrids, and these features can be taxonomic traits that clarify species names. It also provided useful data for the production (breeding) of the second generation in aquaculture.

The application of 16S rRNA gene pyrosequencing has expanded our knowledge about the respiratory tract microbiome originally obtained using conventional, culture-based methods. In this study, we employed DNA-based molecular techniques for examining the sputum microbiome in bronchiectasis patients in relation to disease severity. Of 63 study subjects, 42 had mild and 21 had moderate or severe bronchiectasis, which was classified by calculating the FACED score based on FEV₁ (forced expiratory volume in 1 s, %) (F, 0–2 points), age (A, 0–2 points), chronic colonization by Pseudomonas aeruginosa (C, 0-1 point), radiographic extension (E, 0–1 point), and dyspnoea (D, 0–1 point). Bronchiectasis was defined as mild at 0–2 points, moderate at 3–4 points, and severe at 5–7 points. The mean age was 68.0 ± 9.3 years; 33 patients were women. Haemophilus (p=0.005) and Rothia (p=0.043) were significantly more abundant in the mild bronchiectasis group, whereas Pseudomonas (p=0.031) was significantly more abundant in the moderate or severe group. However, the alpha or beta diversity did not significantly differ among sputum microbiota, i.e. the same dominating genera were found in all samples. Further large-scale studies are needed to investigate the sputum microbiome in bronchiectasis.

The National Agrobiodiversity Center under the Rural Development Administration (RDA) in Jeonju, Republic of Korea, is the largest international genebank of Korea. The National Agrobi-odiversity Center has continuously been making efforts to introduce overseas genetic resources to its collection and has currently grown into a world-class PGR holding genebank. Currently, several steps are undertaken to, improve the accessibility of the collection to national as well as international researchers, improve data available on the resources and amend the passport in-formation of the accessions. With the implementation of the Nagoya Protocol, the origin of ge-netic resources is being highlighted as an important input in the passport information of germplasms. The RDA-Genebank actively responds to the Nagoya Protocol by supplementing passport data of resources lacking information on the origin of germplasm. In addition, a large number of conserved resources are continuously multiplied, and agronomic traits are investi-gated concurrently. With the traditional methods of characterization of the germplasm requiring a significant amount of time and effort, we have intiated high-throughput phenotyping using digital techniques to improve our germplasm data. Primarily, we have started adding seed phenotype information followed by measuring root phenotypes which are stored under agro-nomic traits. This may be the initial step for a germplasm center to use large-scale high-throughput techniques for their collection. In this shortcommunication, we aim to provide an introduction to the RDA- Genebank, adopted international standards, and establishment of high throughput phenotyping techniques for improvement of passport information.

The aim of this study was to analyze glucosinolates (GSLs) in germplasms that are currently conserved at the RDA-Genebank. The analysis focused on the glucosinolate diversity among the analyzed germplasms, with the goal of identifying those that would be most useful for future breeding efforts to produce nutritionally rich Choy sum plants..Twenty-three accessions of Choy sum which possessed ample background passport information were selected. By analyzing the glucosinolate content for 17 different glucosinolates, we observed aliphatic GSLs to be the most common. We identified one accession, IT228140 to synthesize high quantities of glucobrassi-canapin and progoitrin which have been reported to contain several therapeutic applications. Overall, this study highlights the importance of conserving and analyzing plant genetic re-sources, such as those held in national genebanks, for the purpose of developing new varieties of crops that are both nutritious and beneficial for human health. The identification of excellent germplasms for breeding material and the confirmation of the anticancer effects of glucosin-olates are significant contributions to the field of agricultural research and have the potential to positively impact public health.

In this paper, we define new kind of Daehee numbers, the degenerate Daehee numbers of the third kind, using degenerate log function as generating function. We obtain some identities for the degenerate Daehee numbers of the third kind associated with the Daehee, degenerate Daehee and degenerate Daehee numbers of the second kind. In addition, we derive a differential equation associated with the degenerate log function. We deduce some identities from the differential equation.

The economic development and infrastructure of a nation are closely interrelated. In addition, public trust in national infrastructure facilities is closely linked to the preservation of the advantages provided by these facilities to the public. Since the 1970s, Korea has achieved exponential economic growth over a short period of time and the number of infrastructure facilities has increased correspondingly. This compressed economic development has been underpinned by the national infrastructure, whose safety and usability have been excluded from the scope of the development. However, after around 30 years, structural deterioration coupled with general insensitivity to safety in today’s society has considerably reduced public trust in using the infrastructure. Realistically, policies that mainly focus on developing new technologies related to infrastructure construction have led to practical limitations that discourage the development of technologies for maintenance or inspection. Furthermore, current maintenance works face certain limitations caused by various reasons: insufficient budget, increasing number of infrastructure facilities requiring maintenance, shortage of manpower, and rapidly increasing number of aging infrastructure facilities. To overcome these limitations, a new approach is required that is different from general inspection methods under the existing rules and regulations. In this context, this study aimed to explore the efficiency of bridge inspection and maintenance by unmanned aerial vehicles (UAVs) that could observe inaccessible areas, could be conveniently and easily controlled, and could offer high economic benefits. To this end, various tests were performed on elevated bridges, and suitable UAV images were obtained. The obtained UAV images were inspected by using machine vision technology, thereby excluding subjective evaluations by humans. Methods for enhancing the objectivity of the inspection were also discussed. The test results showed that both the efficiency and objectivity of the proposed method were better than those of the existing bridge maintenance and inspection methods.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

Sea fog event over the Eastern Yellow Sea on 15–16 April 2012 was reproduced in the Weather Research and Forecasting (WRF) simulation with high-resolution to investigate the roles of phys-ical processes and synoptic-scale flows on advection fog with sea surface warming. Initially, longwave radiative cooling (LRC) with negative sensible heat flux (SHF) due to the turbulence af-ter sunset triggered a formation of cloud at the surface under the moist advection with a southerly wind. This is a conventional type of advection fog. At night, continuous cooling due to longwave radiation and SHF near the surface modulated the change of the SHF from negative to positive, resulting in a drastic increase in the latent heat flux (LHF) that provided sufficient moisture at lower atmosphere (self-moistening). This is a favorable condition for advection fog with sea sur-face heating (ssH), and this transition represents advection fog with ssH. Enhanced turbulent mixing driven by a buoyancy force increased the depth of the sea fog with a gradual rise in the marine atmospheric boundary layer (MABL) height, even at nighttime. In addition, cold advec-tion with a prevailing northerly wind at the top of the MABL led to a drastic increase in turbulent mixing and the MABL height, which resulted in rapid growth of the height of sea fog due to ver-tical diffusion. After sunrise, shortwave radiative warming in the fog layers offsetting the LRC near the surface weakened thermal instability, which contributed to the reduction in the MABL height, even during the daytime. In addition, dry advection of northerly wind induced dissipa-tion of the fog via evaporation. An additional sensitivity test of sea surface salinity showed weaker and shallower sea fog than the control due to the decrease in both the LHF and local self-moistening.

Background A mycotic aortic aneurysm is a rare type of aortic aneurysm that can cause serious and adverse outcomes. Most mycotic aneurysms originate from infectious sources, such as trauma, vegetation in the heart, and adjacent infectious sources. If a mycotic aneurysm is diagnosed, it should be treated simultaneously with the primary source of the infection. Case Report A 63-year-old male presented to the emergency room with a fever, the primary source of which had not been confirmed, and had not responded to antibiotic treatment for two weeks. Treatment was initiated for a mycotic aneurysm of the brachial artery that occurred suddenly while undergoing treatment for the fever. Further investigation revealed that a mycotic aneurysm of the brachial artery was the cause of the fever, followed by aneurysms in the abdomen and lower extremities, and even vegetation on the heart that was not initially present. The patient declined to undergo treatment for personal reasons. After five months, a contained rupture of the abdominal aortic aneurysm that was initially considered as normal aorta was diagnosed and was treated successfully. Conclusions A peripheral mycotic aneurysm may be associated with multiple aneurysms. Appropriate diagnosis and complete management are necessary to prevent fatal consequences.

A surgical microscope is large in size, which makes it impossible to be portable. The distance between the surgical microscope and the observation tissue is 15–30 cm, and the adjustment range of the right and left of the camera is a maximum of 30°. Therefore, the surgical microscope is generated attenuation (above 58%) of irradiation optical source owing to the long working distance. Moreover, the observation of tissue is affected because of dazzling by ambient light as the optical source power is strong (55 to 160 mW/cm2). Further, observation blind spot phenomena will occur due to the limitations in adjusting the right and left of the camera. Therefore, it is difficult to clearly observe the tumor. In this study, a compact pen-type probe with a portable surgical microscope is presented. The proposed surgical microscope comprises a small and portable pen-type probe that can adjust the working distance between the probe and the observed tissue. In addition, it allows the adjustment of the viewing angle and fluorescence brightness. The proposed probe has no blind spots or optical density loss.

A surgical microscope is large in size, making portability impossible. The distance between the surgical microscope and the observation tissue is 15 to 30 cm, while the maximum adjustment range of the camera to the right and left is 30°. Therefore, surgical microscopes cause attenuation (above 58%) of the irradiation optical source owing to the long working distance. Moreover, the observation of tissue was dazzled with ambient light because the optical power source was strong (50 to 160 mW/cm2). Owing to the limited ability to adjust the camera to the right and left, a blind spot occurs with a surgical microscope. Therefore, it is difficult to clearly observe a tumor. In this study, a compact pen-type probe with a portable surgical microscope is proposed. The pen-type probe is small with a portable shape, and is capable of adjusting the working distance between itself and the observed tissue. It is also possible to adjust the viewing angle and fluorescence brightness. The proposed pen-type probe has no blind spots or optical density loss.

Blockchain is the consensus-based technology to resolve the conflicts in Byzantine environments. Vehicles validate the messages received from the neighboring vehicles using Gradient Boosting Technique (GBT). Based on the validation results the message source vehicle generates the ratings that are to be uploaded to Road Side Units (RSUs) through that trust offset value can be calculated. All RSUs maintain the trust blockchain and each RSU tries to add their blocks to trust blockchain. We proposed a blockchain-based trust management model for VANET based on Tendermint. It eliminates the problem of malicious nodes entering the network and will also overcome the problem of power consumption. Simulation results also show that the proposed system is 7.8% and 15.6% effective and efficient in terms of Packet Delivery Ratio (PDR) and End-to-End Delay (EED) respectively to collect the trusted data between the vehicles.

For the effective utilization of rice husk, organosolv fractionation was investigated to separate three main components (glucan, xylose, and lignin) with low acid concentration. Reaction temperatures of 170–190 °C, ethanol concentrations of 50–70% (v/v), and sulfuric acid concentrations of 0–0.7% (w/v) were investigated, with the reaction time and liquid-to-solid ratio kept constant at 60 min and 10, respectively. The fractionation conditions for the efficient separation into the three components of rice husk were determined to be 180 °C, 60% (v/v) of ethanol, and 0.25% (w/v) of sulfuric acid. Under these fractionation conditions, 86.8% of the xylan and 77.5% of the lignin were removed from the rice husk, and xylose and lignin were obtained from the liquid in 67.6% and 49.8% yields, respectively. The glucan digestibility of the fractionated rice husk was 85.2% with an enzyme loading of 15 FPU (filter paper unit) of cellulase per g-glucan.

FMD is a highly contagious animal disease that occurs in cloven-hoofed animals including pigs. To prevent FMD, vaccines and adjuvants are used to induce an immune response, but it is not sufficient to show the effect of preventing viral infection. In this study, we conducted to evaluate the increasing effect of FMD vaccine SP antibody by administrating Zn-ASP to 100 pigs from three test pig farms with feed. FMD vaccine antibody titer and immunological index were analyzed using an enzyme-linked immunosorbent assay (ELISA) kit, and hematological and blood biochemical parameters were analyzed using an automatic blood analyzer. The titer of FMD vaccine SP antibody in the 0.2% Zn-ASP-administered group significantly increased compared to that in the positive control group only injected with FMD vaccine at 4 weeks after the first vaccination and at 4, 8 and 16 weeks after the second vaccination, respectively (p&lt;0.05). The FMD vaccine SP antibody positive rate was 100% until shipment. IFN-γ and IgA were significantly increased by Zn-ASP administration 4 weeks after the first vaccination and 4 weeks after the second vaccination (p&lt;0.05). On the other hand, serum AST, and CPK (p&lt;0.001) were significantly decreased by Zn-ASP. Our results show that the administration of Zn-ASP is effective in enhancing the antibody titer and immunity of the FMD vaccine by FMD vaccination, and it is thought that it can be used as an oral adjuvant (OrAd) to prevent viral diseases such as FMD.

The tumor microenvironment of colorectal cancer (CRC) is heterogenous; thus, it is likely that multiple immune-related and inflammatory markers are simultaneously expressed in the tumor. The aim of this study was to identify immune-related and inflammatory markers expressed in freshly frozen CRC tissues and to investigate whether they are related to the clinicopathological features and prognosis of CRC. Seventy patients with CRC who underwent curative surgical resection between December 2014 and January 2017 were included in this study. Tissue samples were obtained from tumor and non-tumor areas in the patients’ colons. The concentrations of immune-related markers (APRIL/TNFSF13, BAFF, LAG-3, PD-1, PD-L1, and CTLA-4) and inflammatory markers (CHIT, MMP-3, osteocalcin, pentraxin-3, sTNF-R1, and sTNF-R2) in the samples were measured using the Bio-plex Multiplex Immunoassay system. The concentrations of APRIL/TNFSF13, BAFF, and MMP-3 in the samples were significantly high; thus, we conducted analyses based on the cutoff values for these three markers. The high APRIL/TNFSH13 expression group showed a significantly higher rate of metastatic lesions than the low expression group, whereas the high MMP-3 expression group had higher CEA levels, more lymph node metastases, and more advanced disease stages than the low expression group. The five-year disease-free survival of the high MMP-3 expression group was significantly shorter than that of the low expression group (65.1% vs. 90.2%, p=0.033). This study provides evidence that the APRIL/TNFSF13, BAFF, and MMP-3 pathway is overexpressed CRC tissues and is associated with unfavorable clinicopathological features and poor prognosis in CRC patients. These markers could serve as diagnostic or prognostic biomarkers for CRC.

Abstract: (1) Background: existing treatment methods for neglect are concentrated on egocentric neglect and lead to various problems, such as cost/space constraints and portability. Therefore, this study seeks to determine how treatment (a.k.a., Twins Therapy, TT) can improve an existing problem in relation to neglect in stroke patients; (2) Method: The research design was a pre-post test control group design and both groups maintained existing rehabilitation treatment and added TT intervention only to the experimental group. TT intervention was conducted for a total of 20 sessions (1 session 30 min/day, 5 days/week for 4 weeks); (3) Result: as a result of comparison be-fore and after the TT intervention, there was no significant difference in MFT and MBI items (p>.05). However, the score and execution time of the Apple Cancellation Test showed significant reduction only in the experimental group (p<.05); (4) Conclusion: as a result of the study, TT im-proved not only egocentric neglect, but also allocentric neglect symptoms in stroke patients

Alopecia refers to the continuous shedding of hair from the scalp or other areas. Genetic factors are the most common of the variety of causes of alopecia. Male pattern baldness, also known as androgenic alopecia, is prevalent. Recently, the interest in hair loss treatment has increased due to the growing number of people experiencing anxiety and stress related to hair loss. Nepenthes kampotiana Lecomte is known for its anticancer effects, but its potential for preventing hair loss has not been researched. Therefore, this study focused on the hair loss prevention effects of N. kampotiana Lecomte ethanol extract (Nk-EE). The results showed that Nk-EE has a proliferative effect on human follicle dermal papilla cells and inhibited cell death. In vivo experiments using androgenic areata models showed that Nk-EE had a positive effect on a variety of biomarkers such as hair-to-skin ratio, hair type frequency, and hair thickness. The results of this study suggest that Nk-EE has the potential to be an effective treatment for androgenic alopecia.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

Though melatonin is known to improve ultraviolet B (UVB)-induced oxidative damage and inflammatory conditions via blockade of nuclear factor (NF)-κB, interleukin (IL)-6, there is no report on anti-wrinkle effect of melatonin to date. Hence in the present study, anti-wrinkle mechanism of melatonin was elucidated in UVB treated HaCaT keratinocytes and hairless mice. Herein melatonin protected against a radical initiator tert-Butyl hydroperoxide (t-BOOH) induced reactive oxygen species (ROS) production, matrix metalloprotease 1 (MMP-1) and cytotoxicity in HaCaT keratinocytes. Also, melatonin suppressed the expression of sonic hedgehog (SHH) and GLI for hedgehog signaling, p-NF-kB, cyclooxygenase (COX-2), p-ERK for inflammatory responses in UVB treated HaCaT keratinocytes. Furthermore, melatonin protected skin from wrinkle formation, transdermal water loss in hairless mice irradiated by UVB for 8 weeks. Notably, melatonin prevented against epidermal thickness and dermal collagen degradation in UVB irradiated hairless mice by Hematoxylin & Eosin and Masson’s trichrome staining. Taken together, these findings suggest that melatonin reduces wrinkle formation via inhibition of ROS/SHH and inflammatory proteins such as NF-kB/COX-2/ERK/MMP1.

Background: This study aimed to present the development process and characteristics of the Korean Registry of Acute Myocardial Infarction for Regional Cardiocerebrovascular Centers (KRAMI-RCC). Methods: We developed KRAMI-RCC, a web-based registry for patients with AMI. Patients from 14 RCCs were registered for more than 3 years from July 2016. It includes an automatic error-checking system, and user training and on-site monitoring are performed to manage data quality. Results: A total of 11,700 AMI patients were registered in KRAMI-RCC over 3 years (73.9% men). The proportions of patients with ST-elevation and non-ST-elevation myocardial infarction at discharge were 43.4% and 56.6%, respectively. Of the total 3-year patients, 5.6% died in the hospital and 4.4% died 12 months after discharge. The case fatality within 12 months was 9.7%. Prehospital care data showed delayed arrival time after onset of symptoms (median 153 min) and low transportation rate by public ambulance (25.2%). Post-hospital care data showed lower participation rate in the second rehabilitation program (16.8%). Conclusions: The recently developed KRAMI-RCC registry has been more focused on pre-hospital and post-hospital data, which will be helpful in understanding the current state of AMI disease management and in making policy decisions to reduce case fatality in Korea.

Background: We aimed to assess the risk of chemotherapy- and radiotherapy-related cognitive impairment in colorectal cancer patients. Methods: We randomly selected 40% of colorectal cancer patients from Korean National Health Insurance Database (NHID), 2004-2018 (N=148,848). Patients with one or more ICD-10 diagnostic codes for dementia or mild cognitive impairment was defined as cognitive impairment cases. Patients who were aged 18 or younger, diagnosed with cognitive impairment before colorectal cancer (N=8,225) and did not receive primary resection (N=45,320) were excluded. The effects of each chemotherapy agent on cognitive impairment were estimated. We additionally estimated the effect of radiotherapy in rectal cancer patients. Time-dependent competing risk Cox regression was conducted to estimate overall and age-specific hazard ratios (HR) separately for colon and rectal cancer. Results: In colon cancer, capecitabine and irinotecan was associated with higher cognitive im-pairment, while 5-fluorouracil was not. In rectal cancer, no chemotherapy agents increased the risk of cognitive impairment, nor did radiotherapy. Hazardous association of irinotecan was estimated larger in elderly patients compared with younger counterparts. Conclusion: Heterogeneous associations between various chemotherapy agents and cognitive impairment were observed. Elderly patients were more vulnerable to possible adverse cognitive effects. Radiotherapy did not increase the risk of cognitive impairment.

Very poor oral health, common among older adults, is associated with cognitive decline.This study aimed to investigate the association between denture use, chewing ability, and cognitive function in Korean middle-aged adults using samples representing middle-aged people at the national level. This longitudinal study included 9,998 middle-aged adults via Korea Longitudinal Study of Aging 7th special survey data. Denture use, chewing ability, health-related factors, and general characteristics were assessed by the Computer Assisted Personal Interview. After controlling general characteristics using a generalized estimating equation model, the association of denture use and MMSE scores with chewing ability of those with or without dentures and MMSE scores were analysed. Twenty-four percent of participants wore dentures among them, 35.1% complained of difficulty chewing when wearing dentures. Among participants who did not wear dentures, 16.4% complained of difficulty chewing. MMSE scores were lower among denture-wearers than non-denture wearers (β = -0.026, p < 0.001). In both groups, MMSE scores decreased with chewing difficulty and were significantly reduced among non-denture wearers (p < 0.05). Chewing ability was closely associated with cognitive function. Given the negative effect of difficulty chewing on cognitive function, maintaining chewing ability should be of great concern.

Regulatory macrophages (Mregs) are unique in that they have anti-inflammatory and immunosuppressive properties. Thus, treating inflammatory diseases using Mregs is an area of active research. Human Mregs are usually generated by culturing peripheral blood monocytes stimulated by macrophage colony-stimulating factor with interferon (IFN)-. Here, we generated Mregs with an elongated cell morphology from THP-1 cells stimulated with phorbol 12-myristate 13-acetate and cultured with arginylglycylaspartic acid and vitamin D3. These Mregs regulated macrophage function, and respectively downregulated and upregulated the expression of pro-inflammatory and immunosuppressive mediators. They also expressed Mregs-specific marker, such as dehydrogenase/reductase 9, even when exposed to inflammatory stimulants such as IFN-, lipopolysaccharide, purified xenogeneic antigen, and xenogeneic cells. The Mregs also exerted anti- inflammatory and anticoagulatory actions in response to xenogeneic cells and immunosuppressive effects on mitogen-induced Jurkat T-cell proliferation. Our method of generating functional Mregs in vitro without cytokines is simple and cost-effective.

This paper proposes a cognitive radio engine platform for making exploitation of available frequency channels usable for a tactical wireless sensor network in presence of incumbent communication devices known as the primary user (PU) required to be protected from undesired harmful interference. In the field of tactical communication networks, it is desperate to find available frequencies for opportunistic and dynamic access to channels in which PU is in active. This paper introduces a cognitive engine plaform for determining available channels on the basis of case-based reasoning technique deployable as core functionality on cognitive radio engine to enable dynamic spectrum access (DSA) with high fidelity. Towards this, this paper introduces a plausible learning engine to characterize channel usage pattern to extract best channel candiates for the tactical cognitive radio node (TCRN). Performance of the proposed cognitive engine is verified by conducting simulation tests which confirm the reliability in functional aspect of the proposed cognitive engine covering the learning engine as well as the case-based reasoning engine with showing how well TCRN can avoid the collision against the PU operation considered as the etiquette secondary user (SU) should have.

Lectins, characterized by their carbohydrate-binding ability, have an extensive practical application. However, their industrial use is limited by low yields, and few active recombinant lectins have been reported. In this study, the algal lectin BPL-3 (Bryopsis plumosa lectin 3) was successfully produced using a bacterial expression system, BL21(DE3), with an artificial repeated structure (dimeric construct). Recombinant dimeric BPL3 (rD2BPL3) was confirmed by LC-MS/MS spectrometry. Expression efficiency was greater for the construct with the repeat structure (rD2BPL3) than the monomeric form (rD1BPL3). Optimal conditions for expression were 1 mM IPTG at 20 °C. Recombinant lectin was purified under denaturing conditions and refolded by the flash dilution method. Recombinant BPL3 was solubilized in 1× PBS containing 2 M urea. rD2BPL3 showed strong hemagglutination activity using human erythrocytes, similar to that of native BPL3. rD2BPL3 had a similar sugar specificity to that of the native protein, i.e., to N-acetyl-glucosamine (GlcNAc) and N-acetyl-galactosamine (GalNAc). Glycan array results showed that recombinant BPL3 and native BPL3 exhibited different binding properties. Both showed weak binding activity to α-Man-Sp. Native BPL3 showed strong binding specificity to the alpha conformation of amino sugars, and rD2BPL3 had binding activity to the beta conformation. The process developed in this study was suitable for the quality-controlled production of high amounts of soluble recombinant lectins.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

This paper studies a multihop amplify-and-forward (AF) simultaneous wireless information and power transfer (SWIPT) relaying system. Each relaying node harvests energy using power splitting (PS) scheme from a part of its received signal to amplify and forward the rest the received signal to the next relay. Based on this system model and signal flow, we derived and solved the convex energy minimization problem with optimal PS ratio. The influence of processing cost was then investigated for the AF-SWIPT system with the decode-and-forward SWIPT as benchmark, where AF-SWIPT was found to be superior.

Marine algae have been considered as abundant source of bioactive compounds with cosmeceutical potential. Recently, a great deal of interest has focused on the health-promoting effects of marine bioactive compounds. Carbohydrate is a major and abundant constitute of marine algae that have been utilized in cosmetic formulations, such as moisturizing and thickening agents. In addition, marine carbohydrates have been suggested as promising bioactive biomaterials for various skin beneficial properties, such as anti-oxidant, anti-melanogenic and anti-skin aging. Therefore, marine algae carbohydrates have potential of skin health benefits for value-added cosmeceutical application. The present review focused on the various biological capacities and potential skin health benefits of bioactive marine carbohydrates.

Radiotherapy for cancer has been known to affect the responses of immune cells, especially those of CD8+ T cells that play a pivotal role in anti-tumor immunity. Clinical success of immune checkpoint inhibitors led to an increasing interest into the ability of radiation to modulate CD8+ T cell responses. Recent studies that carefully analyzed the CD8+ T cell responses following radiotherapy suggest the beneficial roles of radiotherapy on anti-tumor immunity. In addition, numerous clinical trials that evaluate the efficacy of combining radiotherapy with immune checkpoint inhibitors are undergoing. In this review, we summarize the current status of knowledge regarding the changes of CD8+ T cells following radiotherapy from various preclinical and clinical studies. Furthermore, key biologic mechanisms that underlie such modulation, including both direct and indirect effects, are described. Lastly, we discuss the current evidence and essential considerations for harnessing radiotherapy as a combination partner for immune checkpoint inhibitors.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

We simulated the glass-blowing process to model a shell resonator, which is a key component in MRIG (Micro Rate Integrating Gyroscope), using the finite elements method to solve a non-isothermal problem. We also calculated the mechanical characteristics of the modeled resonator, including effective mass, eigenfrequencies, angular gain, and energy loss, to predict the resonator's performance as a gyroscope. One key aspect we addressed is the bending of the resonator's rim toward the stem during glass-blowing process. This phenomenon occurs due to increased heat loss at the mold's edge and reduced heat flux at the side of the Gaussian heat source. To mitigate rim bending and the subsequent reduction in capacitance between the rim and 3D electrodes, which can degrade performance in micro glass-blown shell resonators for gyroscopes, we propose two potential mold solutions. The first is using a short-stem mold, which requires extensive polishing to eliminate the bent rim. The second solution is using a mold with a suitable chamfer at the edge, resulting in a straight rim. To quantitatively compare resonators created by these two types of molds, we calculated the noise factor for predicting its gyroscope performance. From these calculations, we find out that using the chamfered mold enables us to increase in the resonator's effective mass, eigenfrequency, angular gain, and quality factor, consequently reducing the noise factor compared to using the short-stem mold. This simulation process will assist us in getting insight into understanding a shell resonator as a gyroscope, designing a mold and determining experimental conditions.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

Anesthetic management for pregnant suffering from airway pathology poses unique challenges. The presence of bilateral vocal cord granuloma adds further complexity to the management, as it can potentially cause airway compromise and respiratory distress. This case presents a pregnant patient with bilateral vocal cord granuloma who underwent anesthesia using high-flow nasal cannula (HFNC) oxygenation and oxygen reserve index (ORi) monitoring. A 33-year-old pregnant woman, who had undergone intubation six month ago, experienced hoarseness and was ultimately diagnosed with bilateral granuloma. Due to the significant airway obstruction, neither intubation nor ventilation was feasible, thereby requiring a surgical intervention. Before the surgical removal, the patient’s oxygenation was ensured using HFNC oxygenation. After confirming sufficient oxygenation of the patient with ORi of 0.38, the operation commenced and as it lasted approximately 3 minutes, the patient was able to tolerate the brief period without additional oxygen supply. Post-surgical excision, mask bagging and HFNC oxygenation was resumed, driving ORi to 0.39, then the operation was resumed. Throughout the procedure, SpO2 remained above 98. The combination of HFNC and ORi ensured adequate oxygenation and allowed for early detection of hypoxemia during the procedure. This approach may be a good option for managing granuloma.

The number of fishers working on commercial fishing vessels worldwide is approximately 159,800 according to the Food and Agriculture Organization of the United Nations. The International Labour Organization estimates that the mean annual number of deaths during fishing is approximately 24,000. Most guidelines for the prevention of marine accidents have been developed with a focus on vessels involved in international navigation. As these guidelines may have parts that are unsuitable for application in small-scale boats operating in coastal areas, appropriate modifications are required. This study analyzed quantitative data on 1,790 marine accidents that occurred in trap fishery, a globally common type of fishery, and data obtained through a survey of 101 fishers in South Korea. A guideline to reduce the rate of fatal accidents was developed using the Bayesian network, a method used for the analysis of accidents, as suggested in the formal safety assessment protocol. The results of data analysis and the developed guidelines are expected to be beneficial to all fishers involved in trap fishery across many countries worldwide.

Software-based ultrasound imaging systems provide high flexibility that allows easy and fast adoption of newly developed algorithms. However, the extremely high data rate required for data transfer from sensors (e.g., transducers) to the ultrasound imaging systems is a major bottleneck in the software-based architecture, especially in the context of real-time imaging. To overcome this limitation, in this paper, we present a Binary cLuster (BL) code, which yields an improved compression ratio compared to the exponential Golomb code. Owing to the real-time encoding/decoding features without overheads, the universal code is a good solution to reduce the data transfer rate for software-based ultrasound imaging. The performance of the proposed method was evaluated using in vitro and in vivo data sets. It was demonstrated that the BL-beta code has a good stable lossless compression performance of 20 ~ 30% while requiring no auxiliary memory or storage.

1-[5-(4-methylphenyl)-1,3,4-oxadiazol-2-yl]methanamine compound has been successfully synthesized by reacting p-Toluic hydrazide and glycine via polyphosphoric acid condensation route. The course of the reaction was found to be high yielding and the title compound was spectroscopically characterized by FT-IR, DSC, 13C/1H-NMR and Mass spectrometric techniques.

In daily living environments, an individual’s state influences spatial perception. The current study, based on Attention Restoration Theory, aimed to explore differences in the health utility of nature according to individual differences in spatial perception. Cognitive mapping and the Perceived Restorativeness Scale (PRS) were used to assess spatial perception ranges and the restorative effect of the environment. Two spatial perceptual groups were defined: one describing only the internal area of a green space, and another illustrating the external area of this green space on a larger scale. The former had higher overall PRS, Being Away, Fascination, and Compatibility scores. The latter had higher scores only on the Coherence subscale. These results illustrate that frequency of nature visits and time spent traveling to do so differently influence the two groups’ attentional restoration, which has great implications for landscape planning in highly stressful urban environments.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

In urban areas, deep excavation-induced ground deformation may damage adjacent existing structures and is conventionally evaluated by levelling at installed settlement points. However, a small number of measurements cannot represent the total change in ground deformation adjacent to excavation sites. Furthermore, significant local subsidence may occur in places where settlement points have not been installed and only noticed after an accident. For deep excavation sites located in urban areas, paved pedestrian sidewalks are often located adjacent to sites, and construction activity can cause these paving blocks to displace. This study introduces a method to detect paving block displacement adjacent to deep excavation sites using terrestrial photogrammetry. A digital camera creating point cloud data (PCD) and an acquisition method satisfying the frontal and side overlap requirements were demonstrated. To investigate the displacement detection and measurement capabilities by PCD analysis, an experimental program was conducted, including a PCD comparison containing the uplift, settlement, and horizontal paving block displacement and reference data. The cloud-to-cloud distance computation algorithm was adopted for PCD comparison. Paving block displacement was detected for displacements of 5, 7.5, and 10 mm in the uplift, settlement, and horizontal directions; however, the horizontal displacements were less clear. PCD analysis enabled satisfactory measurements between 0.024 and 0.881 mm for the vertical-displacement cases, but a significant error was observed for the horizontal-displacement cases owing to the cloud-comparison algorithm. The measurement blind spot of limited settlement points was overcome by the proposed method that detected and measured paving block displacement adjacent to excavation sites.

Eight compounds were isolated from the roots of Glycyrrhiza uralensis and tested for cholinesterase (ChE) and monoamine oxidase (MAO) inhibitory activities. Glycyrol (GC) effectively inhibited butyrylcholinesterase (BChE) and acetylcholinesterase (AChE) with IC50 values of 7.22 and 14.77 µM, respectively, and also moderately inhibited MAO-B (29.48 µM). Six of the other seven compounds only weakly inhibited AChE and BChE, whereas liquiritin apioside moderately inhibited AChE (IC50 = 36.68 µM). Liquiritigenin (LG) potently inhibited MAO-B (IC50 = 0.098 µM) and MAO-A (IC50 = 0.27 µM), and liquiritin, a glycoside of LG, weakly inhibited MAO-B (&gt; 40 µM). GC was a reversible, noncompetitive inhibitor of BChE with a Ki value of 4.47 µM, and LG was a reversible competitive inhibitor of MAO-B with a Ki value of 0.024 µM. Docking simulations showed that the binding affinity of GC for BChE (-7.8 kcal/mol) was greater than its affinity for AChE (-7.1 kcal/mol), and suggested that GC interacted with BChE at Thr284 and Val288 by hydrogen bonds (distances: 2.42 and 1.92 Å, respectively) beyond the ligand binding site of BChE, but that GC did not form hydrogen bond with AChE. The binding affinity of LG for MAO-B (-8.8 kcal/mol) was greater than its affinity for MAO-A (-7.9 kcal/mol). These findings suggest GC and LG should be considered promising compounds for the treatment of Alzheimer’s disease with multi-targeting activities.

Neurofibromatosis type 2 (NF2) is a genetic syndrome characterized by the growth of benign tumors in the nervous system, particularly bilateral vestibular schwannomas, meningiomas, and ependymomas. This review consolidates the current knowledge on NF2 syndrome, emphasizing the molecular pathology associated with the mutations in the gene of the same name, the NF2 gene, and the subsequent dysfunction of its product, the Merlin protein. Merlin, a tumor suppressor, integrates multiple signaling pathways that regulate cell contact, proliferation, and motility, thereby influencing tumor growth. The loss of Merlin disrupts these pathways, leading to tumorigenesis. We discuss the roles of another two proteins potentially associated with NF2-deficiency as well as Merlin: Yes-associated protein 1 (YAP), which may promote tumor growth, and Raf kinase inhibitory protein (RKIP), which appears to suppress tumor development. Additionally, this review discusses the efficacy of various treatments, such as molecular therapies that target specific pathways or inhibit neomorphic protein-protein interaction caused by NF2-deficiency. This overview not only expands on the fundamental understanding of NF2 pathophysiology but also explores the potential of novel therapeutic targets that affect the clinical approach to NF2 syndrome.

Cardiovascular disease is the leading cause of death worldwide. A key factor in assessing the risk of cardiovascular disease is left ventricular functional evaluation. Left ventricular (LV) systolic function is evaluated by measuring the left ventricular ejection fraction (LVEF) using echocardiography data. Therefore, quick and accurate left ventricle segmentation is important for estimating the LVEF. However, it is difficult to accurately segment the left ventricle due to changes in the shape and area of the left ventricle during cardiac cycles. In this study, we proposed a framework that considers changes in the shape and area of the left ventricle during the cardiac cycle by applying the convolutional long short-term memory (CLSTM) approach. In addition, we evaluated the left ventricular segmentation and multidimensional quantification of the proposed system in comparison to manual and automated segmentation methods. In addition, to assess the validity of CLSTM, the values of multi-dimensional quantification metrics were compared and analyzed using graphs and Bland–Altman plots on a frame-by-frame basis. We demonstrated that the CLSTM method effectively segments the left ventricle by considering the LV activity. In conclusion, we demonstrated that LV segmentation based on our framework may be utilized to accurately estimate LVEF values.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

The object of this study was to discover an alternative therapeutic agent with fewer side effects against acne vulgaris, which is one of the most common skin diseases. Acne vulgaris often associates with acne-related bacteria such as <i>Propionibacterium acnes</i>, <i>Staphylococcus epidermidis</i>, <i>Staphylococcus aureus</i> and <i>Pseudomonas aeruginosa</i>, some of which exhibit a resistant against commercial antibiotics used in the treatment of acne vulgaris (tetracycline, erythromycin, and lincomycin). In the current study, we evaluated <i>in vitro</i> antibacterial activity of chitosan-phytochemical conjugates against acne-related bacteria. Three of chitosan-phytochemical conjugates used in this study showed stronger antibacterial activity than that of chitosan (unmodified control). Chitosan-caffeic acid conjugate (CCA) exhibited the highest antibacterial activity against acne-related bacteria with minimum inhibitory concentration values of 8 μg/mL to 256 μg/mL. In addition, the MICs of antibiotics against antibiotic resistant <i>P. acnes</i> and <i>P. aeruginosa</i> strains were dramatically reduced in the combination with CCA, suggesting that CCA would restore the antibacterial activity of the antibiotics. The analysis of fractional inhibitory concentration indices clearly revealed a synergistic antibacterial effect between CCA and the antibiotics. Thus, the median ∑FIC values against the antibiotic resistant bacterial strains were ranged from 0.375 to 0.533 in the combination mode of CCA and antibiotics.

Inflammatory bowel diseases (IBD), including Crohn's disease and ulcerative colitis, is a disease of chronic inflammatory conditions of the intestinal tract due to disturbance of the inflammation and immune system. Symptoms of IBD include abdominal pain, diarrhea, bleeding, reduced weight, and fatigue. In IBD, the immune system attacks the intestinal tract's inner wall, causing chronic inflammation and tissue damage. In particular, IL-6 and IL-17 act on immune cells, including T cells and macrophages, to amplify the immune responses so that tissue damage and morphological changes occur. Of note, excessive calorie intake and obesity also affect the immune system due to inflammation caused by lipotoxicity and changes in lipids supply. Similarly, individuals with IBD have alterations in liver function after sustained high-fat diet feeding. In addition, excess dietary fat intake, along with alterations in primary and secondary bile acids in the colon, can affect the onset and progression of IBD because inflammatory cytokines contribute to insulin resistance; the factors include the release of inflammatory cytokines, oxidative stress, and changes in intestinal microflora, which may also contribute to the disease progression. However, interfering with de novo fatty acid synthase by deleting the enzyme acetyl-CoA-carboxylase 1 in intestinal epithelial cells leads to the deficiency of epithelial crypt structures and tissue regeneration, which seems to be due to Lgr5+ intestinal stem cell function. Thus, conflicting reports exist regarding high-fat diet effects on IBD animal models. This review will focus on the pathological basis of the link between dietary lipids intake and IBD and cover currently available pharmacological approaches.

Arthroscopic capsular release (ACR) is used for persistent shoulder stiffness after an index surgery. No cases of post-ACR humeral head osteonecrosis have been reported to date. A 56-year-old male patient underwent open reduction and internal fixation using a hook plate for acromioclavicular joint dislocation. Despite hardware removal, the patient presented with unresolved shoulder pain and range-of-motion (ROM) limitation. He had a history of hypertension, chronic hepatitis B infection, and alcohol consumption. Preoperative ROM was forward flexion 90°and internal rotation sacral level. Preoperative functional status was visual analog scale (VAS) score 4, American Shoulder and Elbow Surgeons (ASES) score 51, and Constant–Murley (CMS) score 48, and normal radiography and magnetic resonance imaging. Standard ACR was performed with 360° release of the joint capsule via electrocautery ablation. Six-months post-ACR, ROM (forward flexion: 135°, abduction: 135°, external rotation: 70°, internal rotation: T10 vertebra) and functional outcomes (VAS 2; ASES79; CMS 75) were significantly improved, without interval change in radiographic assessment. However, 21 months later, he had recurrent shoulder pain and decreased ROM. Radiography revealed humeral head osteonecrosis. Patients with intrinsic or extrinsic risk factors related to humeral head circulation disturbance should be monitored for humeral head osteonecrosis post-ACR.

This paper proposes a hybrid medium access control (MAC) protocol for wireless sensor network (WSN) data gathering, employing unmanned aerial vehicles (UAV). The UAV sends a beacon frame periodically to inform sensor nodes regarding its presence. Afterward, each sensor node which receives beacon frame contends to send registration frame to the UAV. The UAV will transmit the second beacon frame to the registered nodes to notify their transmission schedule. The time-slot scheme is used for the transmission schedule. The transmission schedule of each sensor is determined based on their priority. Specifically, the priority of each sensor is determined during the registration process. Furthermore, the architecture of UAV-WSN data gathering system is introduced in this paper. Simulations are performed, showing that the proposed MAC protocol achieves fairness while enhancing network performance.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Background The Delta Neutrophil Index (DNI), a prodiagnostic marker for sepsis, utilizes leukocyte count. Platelet activation, similar to leukocytes, plays a crucial role in host defence against pathogens and may serve as a predictor of sepsis outcome. However, the combined evaluation of Mean Platelet Component (MPC) and DNI in assessing sepsis has been rarely used. Methods To assess the prodiagnostic validity of simultaneous utilization of DNI and MPC in cases of human febrile sepsis, we conducted measurements of cellular indices, including DNI and MPC, as well as molecular biomarkers such as procalcitonin (PCT) and C-reactive protein (CRP). This study was carried out on patients admitted to the emergency department with suspected sepsis. Results Using a cutoff value of 2.65%, the sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of DNI in sepsis were found to be 69%, 73.9%, 77.9%, and 64.1%, respectively. Furthermore, significant differences in DNI and MPC levels were observed between the sepsis and non-sepsis groups (6.7±7.8% versus 2.1±2.2%, P=0.000 and 26.0±1.9 g/dl versus 26.8±1.4 g/dl, P=0.002), respectively. Notably, there was a negative correlation between DNI and MPC, with the strength of the correlation varying based on the cause of sepsis. By setting the cutoff value for DNI at 6.2%, the sensitivity, specificity, and NPV improved to 100%, 80.3%, and 100%, respectively, although the PPV remained at 10.6%. Importantly, the DNI≥6.2 group exhibited a higher incidence of death (10.9%, 5/46) and multiorgan failure (19.6%, 9/46) compared to the DNI<6.2 group (0.0%, 0/46 and 0.0%, 0/167, respectively) (P=0.000 and P=0.000, respectively). Conclusions In our study, DNI demonstrates superior effectiveness compared to other molecular biomarkers such as CRP and procalcitonin in distinguishing febrile septic patients from febrile nonseptic patients and predicting prognosis. Additionally, there exists a negative correlation between MPC and DNI, making MPC a valuable marker for differentiating the etiology of sepsis. These findings hold significant clinical implications as DNI/MPC is a cost-effective and readily applicable approach in various impending sepsis scenarios. Notably, this study represents the first examination of the prodiagnostic validity of simultaneously employing DNI and MPC in human cases of febrile sepsis.

A portable urea sensor for use in the fast flow condition was fabricated using porous polytetrafluoroethylene (PTFE) membranes coated with amine-functionalized parylene, parylene-A, by vapor deposition. To generate a specific electrochemical sensor signal from urea, the urea-hydrolyzing enzyme urease was immobilized on the parylene-A-coated PTFE membranes via chemical crosslinking using glutaraldehyde. The urease-immobilized membranes were assembled in a polydimethylsiloxane (PDMS) fluidic chamber, and a screen-printed carbon three-electrode system was used for electrochemical measurements. The success of urease immobilization was confirmed using fluorescence microscopy, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The optimum concentration of urease for immobilization on the parylene-A-coated PTFE membranes was determined to be 48 mg/mL, and the optimum number of membranes in the PDMS chamber was found to be 8. Using these optimized conditions, we fabricated the urea biosensor and monitored urea samples under various flow rates ranging from 0.5 to 10 mL/min in the flow condition using chronoamperometry. To test the applicability of the sensor for physiological samples, we used it for monitoring urea concentration in the waste peritoneal dialysate of a patient with chronic renal failure, at a flow rate of 0.5 mL/min.

The Advanced Meteorological Image (AMI) onboard GEOKOMPSAT 2A (GK-2A) enables the retrieval of dust aerosol optical depth (DAOD) from geostationary satellites using infrared (IR) channels. IR observations allow the retrieval of DAOD and the dust layer altitude (24 hour) over surface properties, particularly over deserts. In this study, dust events in northeast Asia from 2020 to 2021 were investigated using five GK-2A thermal IR bands (8.7, 10.5, 11.4, 12.3, and 13.3 μm). For the dust cloud, the observed brightness temperature differences (BTDs) of 10.5 and 12.3 μm were found to be always negative, while the BTD of 8.7 and 10.5 μm varies relying on the dust intensity. Making the best use of optical properties, a physical approach for DAOD lookup tables (LUTs) was developed using IR channels to retrieve the DAOD. This study simulated the characteristics of thermal radiation transfer using the forward model and dust aerosols can explain by BTD (10.5, 12.3 μm), which is an intrinsic characteristic of dust aerosol. The DAOD and property of dust can be gained from the brightness temperature (BT) of 10.5 μm and the BTD of 10.5, 12.3 μm. Additionally, the cumulative distribution function (CDF) was employed to strengthen the continuity of 24-hour DAOD, which was applied to the algorithm by calculating the conversion value coefficient for the DAOD error correction of the IR with daytime visible aerosol optical depth (VAOD) as the true value. The results show that DAOD product can be successfully used during both daytime and nighttime to continuously monitor the flow of yellow dust from the GK-2A satellite in northeast Asia. In particular, the validation result of IR DAOD was similar to that of the active satellite product (CALIPSO/CALIOP), which showed a tendency similar to that for IR DAOD at night.

Background and Objectives: The novel double-pigtail catheter (DPC) has an additional pigtail coiling at the mid-shaft with centripetal multiple side holes. The aim of the present study was to investigate the advantages and efficacy of DPC in overcoming the complications of conventional single-pigtail catheters (SPC) used to drain pleural effusion. Materials and Methods: Between July 2018 and December 2019, 382 pleural effusion drainage procedures were reviewed retrospectively (DPC, n = 156; SPC without multiple side holes, n = 110; SPC with multiple side holes [SPC+M], n = 116). All patients showed shifting pleural effusion in the decubitus view of chest radiography. All catheters were 10.2 Fr in diameter. One interventional radiologist performed all procedures and used the same anchoring technique. Complications (dysfunctional retraction, complete dislodgement, blockage, and atraumatic pneumothorax) were compared among the catheters using chi-square and Fisher’s exact tests. Clinical success was defined as improvement in pleural effusion within 3 days without additional procedures. A survival analysis was performed for calculating the indwelling time. Results: The dysfunctional retraction rate of DPC was significantly lower than that of the other catheters (p < .001). Complete dislodgement did not occur in any of the DPC cases. The clinical success rate of DPC (90.1%) was the highest. The estimated indwelling times were nine (95% confidence interval [CI]: 7.3–10.7), eight (95% CI: 6.6–9.4), and seven (95% CI: 6.3–7.7) days for SPC, SPC+M, and DPC, respectively, with DPC showing a significant difference (p < .05). Conclusions: DPC had a lower dysfunctional retraction rate compared to conventional drainage catheters. Furthermore, DPC were efficient for pleural effusion drainage with a shorter indwelling time.

Abstract: Global ecological concern regarding the transfer of fouling organisms to ship hulls is increasing. This study investigated the species composition, dominant species, distribution patterns, community structure, and life-cycle differences of hull-fouling macroinvertebrates on five research vessels (R/Vs: Isabu, Onnuri, Eardo, Jangmok 1, and Jangmok 2) operated by the Korea Institute of Ocean Science and Technology (KIOST). Hull-fouling macroinvertebrates were collected three to five times on quadrats from the upper and middle sectors of the hull sides, bottom, and niche areas (the propellers and shafts and the thrusters). A total of 47 macroinvertebrate species were identified, represented by 8,519 individuals(ind.)/m2 and a biomass of 1,967 gWWt/m2 on the five vessels. The number of species, density, and biomass were greater on the coastal vessels the Eardo, Jangmok 1, and Jangmok 2 than on the ocean-going vessels the Isabu and Onnuri. Among the coastal vessels, barnacles were the most abundant and had the greatest density, while mollusks had the highest biomass. Differences between hull sectors showed that the highest species abundance and density appeared on all hulls in ports and bays where the Jangmok 1 operated, while the highest species abundance, density, and biomass were identified in the niche areas of the Eardo, which operated farther from the coast. The hull-fouling macroinvertebrates that exceeded 1% of all organisms were the barnacles Amphibalanus amphitrite, Balanus trigonus, and Amphibalanus improvisus; the polychaete Hydroides ezoensis; the bivalves Magallana gigas and Mytilus galloprovincialis; and the amphipod Jassa slatteryi. The dominant species were cosmopolitan and globally distributed, and many of them were cryptogenic. Six native species were identified: M. gigas, H. ezoensis, the amphipod Melita koreana, the isopod Cirolana ko-reana, and the barnacle B. trigonus and F. kondakovi. Eight non-indigenous species (NIS) were de-tected: barnacles A. amphitrite and A. improvisus, the bivalve M. galloprovincialis, the polychaete Perinereis nuntia, amphipods J. slatteryi and Caprella californica, and bryozoans Bugulina californica and Bugula neritina. Of the fouling macroinvertebrates found on the vessel hulls, 13% were native and 17% were NIS. The nMDS ordination analysis of the five vessels showed four clusters of fouling macroinvertebrate communities: two ocean clusters (the Isabu and Onnuri), one coastal cluster (the Eardo and Jangmok 2), and one local cluster (the Jangmok 1). More diverse communities developed on the hulls of vessels that operated locally rather than globally or in deep oceans. Spearman rank correlation showed that biological indices such as number of species, density, and biomass correlated highly and positively with the numbers of days on coastal operations and negatively with the number days on ocean operations. The species diversity index correlated positively with the total number of anchoring days and coastal operation days and negatively with the total number of operation days and ocean operation days. The macroinvertebrates differed by the area of operation, the port of anchorage, the number of days in operation and at anchor, and the hull sectors. There is no previous research data on hull-fouling macroinvertebrates in the Republic of Korea, and this study provides a basis for future studies to identify introduced species and their differences based on operation area.

Agaricus bisporus is well known as a source of polysaccharides that could improve human health. The objective of this study was to explore anti-obesity effect of A. bisporus extract (H2Oslim®) abundant in polysaccharides and its underlying mechanism. Pancreatic lipase inhibitory activity in vitro was determined after treatment with H2Oslim® and chitosan. Treatment with H2Oslim® and chitosan significantly decreased pancreatic lipase activity. Five-week-old male SD rats were randomly divided into three groups for acute feeding with vehicle, H2Oslim® at 80 mg/kg body weight (BW)/day, and H2Oslim® at 160 mg/kg BW/day. H2Oslim® does-dependently increased plasma lipid clearance in an oral lipid tolerance test. Five-week-old male C57BL/6N mice were fed a control diet (CD), a high fat diet (HFD), an HFD with H2Oslim® at 80 mg/kg BW/day, H2Oslim® at 160 mg/kg BW/day, or chitosan at 160 mg/kg BW/day for eight weeks. HFD-fed mice showed significant increases of body weight, fat mass, white adipose tissue, average lipid droplet size, and serum levels of glucose, triglyceride, ALT, and AST compared to those in the CD group. However, H2Oslim® or chitosan administration ameliorated these increases. H2Oslim® or chitosan signifi-cantly reduced dietary efficiency and increased fecal excretion levels of lipid, triglyceride, and total cholesterol. These in vitro and in vivo findings suggest that H2Oslim® might act as an anti-obesity agent by inhibiting pancreatic lipase-mediated lipid absorption, at least in part.

Krill oil (KO) shows promise as a natural marine-derived ingredient for improving skin health. This study investigated its antioxidant, anti-inflammatory, anti-wrinkle, and moisturizing effects on skin cells and UVB-induced skin photoaging in hairless mice. In vitro assays on HDF, HaCaT, and B16/F10 cells, and in vivo experiments on 66 hairless mice, were conducted. Mice received oral KO administration (100, 200, or 400 mg/kg) once a day for 15 weeks and UVB radiation three times a week. In vitro, KO significantly countered UVB-induced oxidative stress, reduced wrinkles, and prevented skin water loss by enhancing collagen and hyaluronic synthesis. In vivo, all KO dosages showed dose-dependent inhibition of oxidative stress-induced inflammatory photoaging-related skin changes. Skin mRNA expressions for hyaluronan synthesis and collagen synthesis genes also increased dose-dependently after KO treatment. Histopathological analysis confirmed that Krill Oil (KO) ameliorated the damage caused by UVB-irradiated skin tissues. These findings suggest that KO may be a valuable intervention to mitigate UVB-induced skin photoaging and address various skin concerns.