This paper presents a study on the thermal efficiency improvement of the user equipment room in the district heating system based on reinforcement learning [1], and suggests a general method of constructing a learning network(DQN)[2] using deep Q learning[3], which is a reinforcement learning algorithm that does not specify a model. In addition, we introduce the big data platform system and the integrated heat management system for the energy field in the massive data processing from the IoT sensor installed in large number of thermal energy control facilities.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

Radiotherapy for cancer has been known to affect the responses of immune cells, especially those of CD8+ T cells that play a pivotal role in anti-tumor immunity. Clinical success of immune checkpoint inhibitors led to an increasing interest into the ability of radiation to modulate CD8+ T cell responses. Recent studies that carefully analyzed the CD8+ T cell responses following radiotherapy suggest the beneficial roles of radiotherapy on anti-tumor immunity. In addition, numerous clinical trials that evaluate the efficacy of combining radiotherapy with immune checkpoint inhibitors are undergoing. In this review, we summarize the current status of knowledge regarding the changes of CD8+ T cells following radiotherapy from various preclinical and clinical studies. Furthermore, key biologic mechanisms that underlie such modulation, including both direct and indirect effects, are described. Lastly, we discuss the current evidence and essential considerations for harnessing radiotherapy as a combination partner for immune checkpoint inhibitors.

Sarcopenia becomes more common with age, being most prevalent among elderly individuals. According to the EWGSOP, muscle mass is one of the criteria for the evaluation of sarcopenia. The main methods for evaluating muscle mass are CT, MRI, and DXA, but these methods are difficult to apply in the field due to equipment costs, radioactivity, and lack of portability. BIVA and PhA are alternative approaches for assessing somatic cell mass and volume and do not require predictive equations. These variables are clinically relevant parameters that indicate cell health, especially cell membrane integrity and cell function. This study in sarcopenic and nonsarcopenic elderly volunteers aimed to determine the BIVA distribution pattern among individual sarcopenia patients; to evaluate the relationship between PhA and muscle strength, muscle quality, and physical function; and to find any correlates of PhA. The sample comprised 134 free-living elderly individuals of both sexes aged 69–91 years. Anthropometric parameters, grip strength, DXA findings, BIA results, and physical performance (the 6-meter walk test) were measured. Impedance vector distributions were evaluated in sarcopenia patients and healthy elderly individuals using BIVA. According to the AWGS criteria, sarcopenia was diagnosed according to DXA findings, grip strength and physical performance test results. Group differences were evaluated using the t test, Mann‒Whitney U test, and Hotelling's T2 test. Correlation analysis was performed to identify variables significantly associated with PhA. Linear regression analysis was performed to determine whether PhA was associated with muscle strength, muscle quality and physical function. BIVA detected a significant difference between the sarcopenia and non-sarcopenia groups (both sexes) due to higher R/H values and lower phase angles in a few individuals, whereas Xc/Ht values did not differ between the two groups. The sarcopenia group had a significantly lower PhA than the non-sarcopenia group among both males (p<0.01) and females (p<0.05). PhA was significantly correlated with age, ASM, HGS, and muscle quality in both sexes and significantly correlated with ASM/Ht2 and physical performance in males. PhA was a significant indicator of muscle strength in both males (β = 2.6; p<0.01) and females (β = 3.4; p<0.01), a significant indicator of muscle quality in both males (β = 0.07; p<0.05) and females (β = 0.17; p<0.01), and a significant indicator of physical performance in males (β = 0.3; p<0.01). BIVA can detect changes in muscle mass in individuals with sarcopenia and is a practical method for the assessment of sarcopenia in the field. PhA is a good indicator of muscle strength, muscle quality and physical performance (in males). These methods can help diagnose sarcopenia in elderly individuals with reduced mobility.

We present an automated system for nutrient solution management. Prior arts usually measure only pH and EC of the nutrient solutions for maintenance. When EC drops, they just simply add concentrated nutrient to the horticulture bed. Such approach can maintain the density of nutrient solution but cannot maintain the rates of individual ion particles. To prevent nutrition related disorders, fertilization methods with ion selective electrodes are widely introduced. This trend measures individual ion concentration of nutrient solution to maintain appropriate nutrient composition by supplying only insufficient ions. Many researchers have suggested ISE based automated fertilization systems. However, they failed to control a chemical artifact called ion interference effect, which becomes greater at higher density. Our system measures individual concentration of multiple ions and add only deficient nutrients, while handling the ion interference effect issue. To ensure the performance of ion selective electrodes, the system also performs fully automated 3-point calibration 24 times a day. A machine learning algorithm is applied on the sensory parts to remove ion interference effect which make measurement of complex solution with ISE almost impossible. With automated calibration and signal processing technology, the system robustly and continuously maintains nutrient condition for plants. We suggest applying this system on closed hydroponic systems such as smart farms or plant factory, to reduce water consumption and to provide more appropriate environment for the crops.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

Lindera obtusiloba Blume has several activities, such as anti-inflammatory, anti-allergic, anti-tumor, anti-wrinkle, and antioxidant activities. Interleukin-6 (IL-6) is a classic pro-inflammatory cytokine that is associated with various functions, such as proliferation, invasion, inflammatory responses and functions within antioxidant defence systems. In this study, we investigated IL-6-induced STAT3 activation of lignan compounds isolated from L. obtusiloba. The structures of the isolated compounds were elucidated via spectroscopic nuclear magnetic resonance (NMR) and electrospray ionization mass spectrometry (ESI-MS). As a result, seven lignans were identified from L. obtusiloba. All the isolated compounds (1-7) were evaluated for their IL-6-induced STAT3 inhibitory effects in Hep3B cells using a luciferase reporter assay. Of the isolates, compounds 1 and 5 showed inhibitory effects against IL-6-stimulated STAT3 activation. Furthermore, the mRNA expression levels of inflammation-related genes such as CRP, IL-1b, and SOCS3 were significantly reduced by exposure to compound 1 and 5. The protein levels of p-STAT3, p-JAK2 in IL-6 induced U266 cells were regulated in the presence of lignans derived from Lindera obtusiloba by western blot assay. Based on the results, this study of L. obtusiloba demonstrates that the species has promise as a bioactive candidate for the treatment of IL-6-induced STAT3-related disease.

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

Breath volatile organic compound analysis is a non-invasive tool for assessing health status; the compositional profile of these compounds in the breath of patients with chronic kidney disease is believed to change with decreasing renal function. We aimed to identify breath volatile organic compounds for recognizing patients with chronic kidney disease. Using thermal desorption-gas chromatography-mass spectrometry, untargeted analysis of breath markers was performed using breath samples of healthy controls (n=18) versus non-dialysis (n=21) and hemodialysis (n=12) patients with chronic kidney disease in this cross-sectional study. A total of 303 volatile organic compounds alongside 12 clinical variables were used to determine the breath volatile organic compound profile. Metabolomic analysis revealed that age, systolic blood pressure, and fifty-eight breath volatile organic compounds differed significantly between the chronic kidney disease group (non-dialysis + hemodialysis) and healthy controls. Thirty-six volatile organic compounds and two clinical variables that showed significant associations with chronic kidney disease in the univariate analysis were further analyzed. Different spectras of breath volatile organic compounds between the control and chronic kidney disease groups were obtained. Multivariate model incorporating age, 2-methyl-pentane, and cyclohexanone showed high performance (accuracy, 86%) in identifying patients with chronic kidney disease, with odds ratios (95% confidence interval) P-values of 0.18 (0.07-2.49) 0.013; 2.10 (0.94-2.24) 0.025; and 2.31 (0.88–2.64) 0.008, respectively. Hence, renal dysfunction-associated characteristic profiles of breath volatile organic substances can be used as non-invasive markers to screen for chronic kidney disease.

This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

Bacterial communities in rhizosphere and root nodules have significant contributions to the growth and productivity of the soybean (Glycine max L.). In this report, we analyzed the physiological properties and dynamics of bacterial community structure in rhizosphere and root nodules at different growth stages using BioLog EcoPlate and high-throughput sequencing technology, respectively. The BioLog assay found that the metabolic capability of rhizosphere is in increasing trend in the growth of soybeans as compared to the bulk soil. As a result of the Illumina sequencing analysis, the microbial community structure of rhizosphere and root nodules was found to be influenced by the variety and growth stage of the soybean. At the phylum level, Actinobacteria were the most abundant in rhizosphere at all growth stages, followed by Alphaproteobacteria and Acidobacteria and the phylum Bacteroidetes showed the greatest change. But, in the root nodules Alphaproteobacteria were dominant. The results of the OTU analysis exhibited the dominance of Bradyrhizobium during the entire stage of growth, but the ratio of non-rhizobial bacteria showed an increasing trend as the soybean growth progressed. These findings revealed that bacterial community in the rhizosphere and root nodules changed according to both the variety and growth stages of soybean in the field.

We investigate the behavior of the partial derivative approach to the change of scale formula and prove relationships among the analytic Wiener integral and the analytic Feynman integral of the partial derivative for the function space integral.

As a growing public interest in social health of elderly, studies focusing on social networks and interpersonal relationships of the elderly are needed. The present study was conducted to de-velop a structured interview to evaluate the interpersonal schema based on Self-Defining Memory of elderly. First, the word cues that the elderly often report on interpersonal events were con-firmed. Next, the indices and scoring rules were prepared, including Relationship frequency (RF), Conflict frequency (CF), Dominance mean (Dm), and Warmth mean (Wm). Healthy elderly peo-ple living alone (mean age = 71.81, SD = 3.95) were interviewed. Finally, the correlation between each index and Short form of Korean Inventory of Interpersonal Problems Circumplex Scales (KIIP-SC) was analyzed for criterion validity. The inter-rater reliability was substantial (Kappa = .61 ~ .66). Based on the analysis of criterion validity, the indices of CF, Dm, and Wm indices showed an appropriate level of criterion validity. This study developed a structural interview based on a novel system of reporting autobiographical memory and established indices with appropriate validity to evaluate interpersonal relationships. The interview is expected to identify the characteristics of interpersonal relationships of the elderly and contribute to the establishment of the elderly community, accordingly.

Abstract The aim of our study is to analyse the perception of the families and concerned social workers. The research was conducted in an underprivileged and disadvantaged microregion in North Hungary. The main focus was the perception on the available health, educational, child welfare and social services and supports. The starting point was to enquire the target group’s knowledge of these services. The study examines the extent to which social work is able to provide support to disadvantaged, marginalized families with children, and the way how the dysfunctional operation of the system contributes to the perpetuation of the clients’ life conditions. Analysing the quality of these services and supports is crucial to understand the social mobility chance of the children living in this microregion. The results show that without capability and talent development for the children and given the lack of welfare services, the mobility chance and opportunities of these families are extremely low in Hungary.

In this study, ozone oxidation experiment was carried out for the removal of fluorescent whitening agent which is widely used in textile dyeing and paper industry. The stilbene fluorescent whitening agent has been industrialized since the earliest, and the amount of current production is the highest. Due to the characteristics of the fluorescent whitening agent that cannot be removed by conventional wastewater treatment methods, the fluorescent whitening agent in wastewater treatment has difficulty in using as recycled water in the process. Pre-treatment ozone oxidation experiment was conducted prior to the introduction of Membrane Bio Reactor (MBR) treatment process by converting biodegradable materials into biodegradable materials. The removal efficiencies of fluorescent whitening agents, a diaminostilbene disulfonic acid derivative by ozone oxidation were evaluated by UV254 Scan, COD, T-N and color using a synthetic wastewater sample (COD=433.0 mg/ℓ) and paper and paper mill wastewater (COD=157.2 mg/ℓ).

Computer and Smart Device-assisted Learning (CSDL) has gained increasing attention from educational researchers and practitioners in recent years. However, it remains controversial whether student can benefit from CSDL and what moderator could affect the impact of CSDL. Within the specific context of Korea, where the interest in digital education is steadily increasing, the number of empirical studies exploring the causal effect of CSDL remains relatively scarce. The primary objective of this empirical study was to investigate the impact of CSDL on students' academic achievement in Korea. To achieve this objective, a two-way fixed effect model was employed, utilizing a panel dataset spanning three years derived from the 'Korean Education Longitudinal Study 2013'. The findings revealed a significant positive impact of CSDL on students’ Mathematics achievement. Notably, higher income levels, increased availability of computer resources provided by schools, and the implementation of more individualized education were identified as factors that moderate the effect of CSDL on students' achievement levels in Korean and English subjects. These findings underscore the need for an approach that optimizes the educational benefits of CSDL by considering subject-specific characteristics. Furthermore, this study highlights the importance of allocating educational resources, such as computers and smart devices, and integrating individualized educational activities within the classroom environment.

Ovarian cancer is the common cause of death among gynecological cancers. Although ovarian cancer initially responds to chemotherapy, the frequent recurrence in patients remains a therapeutic challenge. Pyruvate kinase M2 (PKM2) plays a pivotal role in regulating cancer cell survival. However, its therapeutic roles remain unclear. Here, we investigated the anticancer effects of compound 3K, a specific PKM2 inhibitor, on autophagic and apoptotic pathway regulation in SK-OV-3 (PKM2-overexpressing human ovarian adenocarcinoma cell line). The anticancer effect of compound 3K was examined using the MTT and colony formation assay in SK-OV-3. The results of tissue microarray showed that PKM2 expression positively correlated with the severity of the tumor. Moreover, the expression of pro-apoptotic proteins increased in SK-OV-3 following compound 3K treatment. Compound 3K induced AMPK activation, which was accompanied by the inhibition of mTOR. Additionally, this compound inhibited glycolysis, resulting in reduced proliferation in SK-OV-3. Compound 3K treatment suppressed tumor progression in vivo xenograft model. Our findings suggest that the inhibition of PKM2 by compound 3K affected Warburg effects and induced autophagic cell death. Therefore, the use of specific PKM2 inhibitors to block the glycolytic pathway and target cancer cell metabolism represents a promising therapeutic approach for treating PKM2-overexpressing ovarian cancer.

Definitive surgical resection is the preferred treatment for early-stage non-small-cell lung cancer (NSCLC). Research into genetic alterations, including epidermal growth factor receptor (EGFR) mutation, in early stage NSCLC remains insufficient. Here, we investigated the prevalence of genetic alterations in early-stage NSCLC and the association between EGFR mutation and recurrence after complete resection. Between January 2019 and December 2021, 659 patients with NSCLC who underwent curative surgical resection at a single regional cancer center were recruited. We compared the clinical and pathological data between the recurrence and non-recurrence groups. Multivariate logistic regression was used to predict the risk factors for recurrence. Among the 659 enrolled cases, the most common histology was adenocarcinoma (74.5%), followed by squamous cell carcinoma (21.7%). The prevalence of EGFR mutation was 43% (194/451). Among them, L858R point mutation and exon 19 deletion was 52.3% and 42%, respectively. ALK rearrangement was found at 5.7% (26/453), and ROS1 fusion was found at 1.6% (7/441). The recurrence rate of the entire population was 19.7%. In multivariate analysis, the presence of EGFR mutation, stage II or III (vs. stage I), and pathologic subtype (presence of solid type) were associated with recurrence. Among the recurred group, 86.5% of the patients with EGFR mutation experienced distant recurrence compared to only 66.7% of wild-type (p = 0.016), with no significant difference in median disease-free survival (p = 0.983). In conclusion, the prevalence of EGFR mutation, ALK rearrangement, and ROS1 fusion was 43.0%, 5.7%, and 1.6%, respectively in patients with early-stage NSCLC who underwent curative resection. Along with stage II/III and solid pathologic subtype, EGFR mutation was an independent risk factor for recurrence. In the recurrence group, the rate of distant metastasis was higher in patients with EGFR mutation than in those with wild-type.

If an algebra of type $A$ contains a subalgebra which is also an algebra of type $B$, then it is a Smarandache $B$-type $A$-algebra provided the subalgebra of type $B$ contains at least two elements. This generalizes the notion of Smarandache group, where the group of order $\geq 2$ is a subsemigroup of a semigroup. In this paper we investigate a number of such pairings and we deduce a number of conclusions as a consequence.

In this paper, we observe that if X is a set and (Bin(X), □) is the semigroup of binary systems on X, then its center ZBin(X) consists of the locally-zero-semigroups and that these can be modeled as (simple) graphs and conversely. Using this device we show that we may obtain many results of interest concerning groupoids by reinterpreting graph theoretical properties and at the same time results on graphs G may be obtained by considering them as elements of centers of the semigroups of binary systems (Bin(X), □) where X = V(G), the vertex set of G.

This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. By drawing an analogy from Kant’s incongruent counterparts, it posits two identical deterministic worlds -- one comprising a human agent and the other comprising a machine agent. These agents exhibit different types of information processing mechanisms despite their apparent sameness in a causal sense. By postulating the distinctiveness of human over machine intelligence, this paper resolves what it refers to as “the vantage point problem” – namely, how to legitimize a determinist’s assertion of determinism by placing the determinist within the universe.

The construction industry, characterized by its intricate network of stakeholders and diverse workforce, grapples with the challenge of managing information effectively. This study delves into this issue, recognizing the universal importance of safeguarding data, particularly amid rising concerns of unauthorized access and breaches. Aiming to harness the potential of blockchain technology to address these challenges, this study used a hypothetical biographical and safety data of construction workers and securely stored on a Hyperledger Fabric blockchain. Developed within the Amazon Web Services (AWS) cloud platform, this blockchain infrastructure emerged as a robust solution for enhancing data security and privacy. Anchored in the core principles of data security, the model emerges as a potent defender against the vulnerabilities of traditional data management systems. Beyond its immediate implications, this study exemplifies the marriage of blockchain technology and the construction sector, potentially reshaping workforce management, especially in high-risk projects, optimizing risk assessment, resource allocation, and safety measures to mitigate work-related injuries. Practical validation through transaction testing using Hyperledger Explorer validates the model's feasibility and operational effectiveness, serving as a blueprint for the industry's data management. Ultimately, this research not only showcases the promise of blockchain technology in addressing construction data security challenges but also underscores its practical applicability through comprehensive testing, heralding a new era of data management that harmonizes security and efficiency for stakeholders' benefit.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

The negative energy solutions of the Klein-Gordon and Dirac equations have been used to define the antiparticle with the positive energy from the Feynman - Stueckelberg interpretation in the standard model based on the 4-D Minkowski space with the relative time. The negative energy solutions of the Klein-Gordon and Dirac equations are used to define the antiparticles with the negative energy in the present 3-D quantized space model. Note that all the present results are based on the 4-D Euclidean space with the absolute time (t) and relative time (t_l). Then the particle with the positive energy and antiparticle with the negative energy have the 4-D P₄ = TCP = T_cP symmetry. The continuity equations are derived from the Klein-Gordon, Dirac and Schrodinger equations. The Klein-Gordon and Schrodinger equations with the potential barriers are solved. The Klein paradox is explained by using the pair production of the electron with the positive energy and positron with the negative energy under the P₄ = _TcP symmetry, The effective velocity ( c_eff=√2 " c " ) and effective energy ("Etl =" √2 E ) along the relative time axis (ctl) give the relative time momentum of "p_tl"=E_tl/c_eff =(√2 E)/(√2 c)=E/c=p_t=p_x. This indicates that the photons with the energy of E have the constant photon velocity of c and the constant photon momentum of "ptl"=E_tl/c_eff =(√2 E)/(√2 c)=E/c=p_t=p_x. For the negative energy particles, the space momentum directions are opposite to the particle velocity directions because the energy is negative. And the matter collapse to the photons at the very high particle velocity is discussed from the length expansion. It is, for the first time, proposed that the gamma ray burst is originated from the matter collapse to the photons near the black hole. Also, the wave function collapse is explained from the length expansion. The wave function collapse takes place when the measurement makes the particle velocity to be zero. It is concluded that the negative energy solutions of the Klein-Gordon and Dirac equations support the existence of the partner antimatter universe with the negative energy and negative time direction. Our matter universe has the positive energy and the positive time direction.

Human sepsis is one of the leading cause of death worldwide and is known to be a harmful damaging host inflammatory condition, primarily caused by endotoxin released by gram-negative bacteria. Despite antibiotics administration being widely used to treat disease, effective targeted therapeutic strategies for the sepsis are still lacking. Here, we demonstrate that CM1, a derivative of natural polyphenol chrysin, exerts anti-inflammatory activity by inducing the ubiquitin-editing protein TNFAIP3 and NAD-dependent deacetylase sirtuin 1 (SIRT1). We found that CM1 attenuated Toll-like receptor 4 (TLR4)-induced the generation of inflammatory cytokines by inhibiting the extracellular-signal-regulated kinase (ERK)/MAPK and nuclear factor kappa B (NF-κB) signaling pathway. In addition, the treatment of macrophages with CM1 induced the expression of TNFAIP3 and SIRT1 in TLR4-stimulated primary macrophages, however the anti-inflammatory properties of CM1 was disappeared by siRNA silencing of TNFAPI3 or by the genetic and pharmacologic inhibition of SIRT1. Importantly, intravenously administration of CM1 resulted in the decreased susceptibility to endotoxin-induced sepsis, leading to inhibition of the generation of proinflammatory cytokines and neutrophils infiltration into lung than control mice. Collectively, these findings suggest that CM1 has the potential to be a treatment candidate for diverse inflammatory diseases including sepsis.

The properties of the charged dark matters are discussed in terms of the new three-dimensional quantized space model. Because of the graviton evaporations, the very small Coulomb’s constant (k(dd)) of 10 ⁻⁴⁸ k and large gravitation constant (G_N(dd)) of 10⁶ G_N for the charged dark matters at the present time are expected. The tentative values of G and k are used for the explanation purpose. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle. Also, the gravitation constant has been changed with increasing of the time because of the graviton evaporation. In the present work, the B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = 0 are explained as the good candidates of the dark matters. Also, the particle creation, dark matters and dark energy could be deeply associated with the changing gravitation constants (G). It is expected that the changing process of the gravitation constant between the matters from G_N(mm) ≈ 10³⁶ G_N to G_N(mm) = G_N happened mostly near the inflation period. Therefore, during most of the universe evolution the gravitation constant could be taken as G_N(mm) = G_N. And the effective charges and effective rest masses of the particles are defined in terms of the fixed Coulomb’s constant (k) and fixed gravitation constant (G_N). Then, the effective charge of the B1 dark matter with EC = −2/3 e is (EC)_eff = −2/3·10⁻²⁴ e. It is concluded that the photons, gravitons and dark matters are the first particles created since the big bang. The particles can be created from the decay of the matter universe and the pair production of the particle and anti-particle with decreasing of the gravitation constant (G_N(mm)). Also, the weak force, strong force and dark matter force bosons are created from the interactions of the elementary particles with the T fluctuations of the vacuum energy.

Ongoing climate change causes abnormal climate events worldwide such as increasing temperatures and changing rainfall patterns. With South Korea facing growing damage from the increased frequency of localized heavy rains, the country is not an exception. In particular, its steep slope lands, including mountainous areas, are vulnerable to damage from landslides and debris flows. In addition, localized short-term heavy rains that occur in urban areas with extremely high intensity tend to lead a sharp increase in damage from soil-related disasters and cause huge losses of life and property. Currently, South Korea predicts landslides and debris flows using the standards for forecasting landslides and heavy rains. However, as the forecasting is conducted separately for rainfall intensity and accumulated rainfall, this lacks a technique that reflects both amount and intensity of rainfall in an episode of localized heavy rainfall. This study, therefore, aims to develop such a technique by collecting past cases of debris flow occurrences and rainfall events that accompanied debris flows to calculate the rainfall triggering index (RTI) reflecting accumulated rainfall and rainfall intensity. In addition, the RTI is converted into the critical accumulated rainfall (Rc) to use precipitation information and provide real-time forecasting. The study classifies the standards for flow debris forecasting into three levels: ALERT (10%–50%), WARNING (50%–70%), and EMERGENCY (70% or higher), to provide a nomogram for 6 hr, 12 hr, and 24 hr. As a result of applying this classification into the actual cases of Seoul, Chuncheon, and Cheongju, it is found that about 2–4 hr of response time is secured from the point of the Emergency level to the occurrence of debris flows.

The spin magnetic moments and spin g factors (g_s = -2) of electron, muon and tau are explained based on the electric charges (EC) and lepton charges (LC) in terms of the three-dimensional quantized space model. The spin g factors of electron, muon and tau are g_s = -2 which is the sum of the EC g factor (g_EC = -1) and the LC g factor (g_LC = -1). The spin g factor (g_s = -2) of the electron is predicted by the Dirac’s equation. The orbit g factors of electron, muon and tau are g_L = g_EC = -1 from the EC g factor (g_EC = -1) without the contribution of the LC g factor (g_LC = -1). The spin g factors of the elementary fermions are calculated from the equation of g_s = g_EC + g_LC + g_CC where g_EC = EC/|EC|, g_LC = LC/|LC| and g_CC = CC/|CC|. For example, the spin g factors of the neutrinos and dark matters are g_s = -1. The spin g factors of the u and d quarks are g_s = 0 and g_s = -2, respectively. The g factor problem of neutrinos with the non-zero LC charges are solved by the LC Coulomb force of F_c(LC) ≈0. It is, for the first time, proposed that the binary motion (fluctuations) of the m_EC and m_LC masses for the electron, muon and tau leptons make the anomalous g factor. This binary motion could be originated from the virtual particle processes including the photons. Also, the weak force (beta) decay is closely related to the binary motion of the m_EC and m_LC for the electron, muon and tau leptons.

The properties of the dark matter, dark energy, graviton and photon are discussed in terms of the new three-dimensional quantized space model. Three new particles (bastons) with the electric charges (EC) are proposed as the dark matters. It is proposed that the EC, LC and CC charges are aligned along the time axes but not along the space axes. The photon is confined on its corresponding three-dimensional quantized space. However, the graviton can be evaporated into other three-dimensional quantized spaces. The rest mass of the electron neutrino (n_e) of 3.494·10⁻³ eV/c² is obtained from the experimental vacuum energy density in terms of quantum field theory (QFT). The rest mass and force range of the massive g(0,0,0) graviton with the Planck size are m_g = 3.1872·10⁻³¹ eV/c² and x_r = 3.0955·10²³ m = 10.0 Mpc, respectively, based on the experimental rest mass and rms charge radius of the proton. The possible diameter (10 Mpc) of the largest galaxy cluster is remarkably consistent with the gravitational force range (10 Mpc). Then, the diameter of the largest dark matter distribution related to the largest galaxy cluster is 9.2865·10²³ m = 30 Mpc equal to the force range of the massive g(0) graviton with the rest mass of 1.0624·10⁻³¹ eV/c². Because of the huge number (N) of the evaporated gravitons, the very small Coulomb’s constant of about 10⁻⁴⁸k and large gravitation constant of 10⁶G_N are expected for the charged dark matters. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = 0 for the proton-like particle. The proposed weak gravitational force between the dark matters and normal matters explains the observed dark matter distributions of the bullet cluster, Abell 1689 cluster and Abell 520 cluster. The transition from the galaxy without the dark matters to the galaxy with the dark matters are explained. Also, the accelerated space expansion is caused by the new space quanta created by the evaporated gravitons into the x1x2x3 space and repulsive electromagnetic force between dark matters corresponding to the dark energy. The decreasing coupling constant of the strong force, neutron lifetime anomaly and the pressure distribution inside the proton are explained by the unobservable proton and hadronization. And the rest mass of 1.4 TeV/c² is assigned to the Le particle with the EC charge of −2e. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. Also, the gravitation constant has been changing with the time because of the graviton evaporation.

The time symmetry of T_c = CT is redefined based on the 4-D Euclidean space. The time inversion symmetry of T_c = CT changes the signs of the charge (q) and absolute time (ct) of the particle. The P symmetry changes the signs of the space momenta and handedness of the particle. The T_c symmetry changes the signs of the time momentum (P_t=E/c) and charges. The handedness are classified as the left-handedness and right-handedness on the 3-D space. The charges (|q| = cDt) and energies (E= cDtDV) of the particles are originated from the upward warping (q>0) and downward warping (q<0) of the particles along the time axis. The evolution of our matter universe with P_t > 0 since the big bang can be interpreted based on the CTP symmetry with the partner antimatter universe with p_t < 0. The photon space is called as the vacuum space. Then the E and M waves are the space fluctuations, and the gravitational G wave is the time fluctuations. And the E, M and G fields are newly explained. The zero E and M fields of the photon space indicates that the photon space and gamma ray are the 2EM waves. The rest mass energy of the particle is the 4-D space volume of the warped photon space. In the present work, the quantum wave function is considered as the 4-D vector with the space wave function and time axis wave function in the 4-D Euclidean space. The warped photon space corresponds to the squared wave function which is the probability density. It is concluded that, in the quantum mechanics, the imaginary number concept is introduced in the quantum wave functions instead of the time axis component of the 4-D wave function vector. The left-handed neutrino puzzle is explained from the handedness partner relation with the right-handed dark matters. Finally, the modified Lorentz transformations derived in the 4-D Euclidean space are compared with the Lorentz transformations of the special and general relativity theories in the 4-D Minkowski space.

In the present work, the charged B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = k(lq) = 0 are explained as the good candidates of the dark matters. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. The missing neutrinos are newly explained by using the dark matters and lepton charge force. The neutrino excess anomaly of the MinibooNE data is explained by the B1 dark matter scattering within the Cherenkov detectors. And the rest masses of 1.4 TeV/c² and 42.7 GeV/c² are assigned to the Le particle and the B2 dark matter, respectively, from the cosmic ray observations. In the present work, the Q1 baryon decays are used to explain the anti-Helium cosmic ray events. Because of the graviton evaporation and photon confinement, the very small Coulomb’s constant (k(dd)) of 10^x-54k and gravitation constant (G_N(dd)) of 10^xG_N for the charged dark matters at the present time are proposed. The x value can have the positive, zero or negative value around zero. Therefore, F_c(mm) > F_g(dd) (?) F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle.

In the present work, the charged dark matters of B1, B2 and B3 bastons are explained as the right-handed partners of the left-handed neutrinos. The new Higgs mechanism of SU(2)_DM×SU(2)_Weak×SU(2)_Strong including electromagnetic and gravitational forces is applied. And the rest masses of the elementary particles depend on their charge configurations. The left-handed neutrinos have only the lepton charges (LC) and the right-handed dark matters have only the electric charges (EC). This explains the fact that the rest masses of the left-handed neutrinos are so small, and the rest masses of the right-handed dark matters are relatively very large. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. The missing neutrinos are newly explained by using the dark matters and lepton charge force. The neutrino excess anomaly of the MinibooNE data is explained by the B1 dark matter scattering within the Cherenkov detectors. The quark mixing and neutrino mixing are not required in the present model. It is shown that our matter universe and its partner antimatter universe can be created from the big bang in the point of view of time -, charge -, space -, and quantum state – symmetric universe evolution.

Origins of the time, mass, electric charges and magnetic monopoles are explained. The energies, electric charges and magnetic charges of the particles are defined as E = cDtDV and |q| = cDt = E/DV, and |q_m| = c²Dt, respectively, for the 3-D quantized spaces warped along the time axis direction of ct in the 4-D Euclidean space. The energy (or mass) and charges (or electric charges and magnetic charges) are the vectors along the time axis of ct in the 4-D Euclidean space. This new concept is closely connected to the wave function of the quantum mechanics. The electric charges, magnetic charges and energies have the property of the space direction independence. Magnetic monopoles (charges) are the force carrying bosons with the inside electric field time loop. Electric monopoles are the elementary fermions. Photon space fluctuations are explained with the quantized magnetic charges.

Space-time evolution of our universe is explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (E = cDtDV), charges and energy density (|q| = r = cDt) and absolute time (ct) are newly defined based on the 4-D Euclidean space. The photon flat space with the constant energy density of r = cDt_q is proposed as the dark energy (DE). The dark energy is separated into the n DE and photon DE which create the new photon spaces with the constant energy density of r = cDt_q. The v DE is from the n pair production by the CPT symmetry and the photon DE is from the photon space pair production by the T symmetry. The vacuum energy crisis and Hubble’s constant puzzle are explained by the photon space with the n DE and photon DE. The big bang and inflation of the primary black hole is connected to the accelerated space expansion and big collapse of the photon space through the universe evolution. The big bang from the nothing is the pair production of the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry. Our universe is the matter universe with the negative charges of electric charge (EC), lepton charge (LC) and color charge (CC). This first universe is made of dark matter -, lepton -, and quark - primary black holes with the huge negative charges which cause the Coulomb repulsive forces much bigger than the gravitational forces. The huge Coulomb forces induce the inflation of the primary black holes, that decay to the super-massive black holes and particles.

The relative force strengths of the Coulomb forces, gravitational forces, dark matter forces, weak forces and strong forces are compared for the dark matters, leptons, quarks, and normal matters (p and n baryons) in terms of the 3-D quantized space model. The quark confinement and asymptotic freedom are explained by the CC merging to the A(CC=-5)₃ state. The proton with the (EC,LC,CC) charge configuration of p(1,0,-5) is p(1,0) + A(CC=-5)₃. The A(CC=-5)₃ state has the 99.6% of the proton mass. The three quarks in p(1,0,-5) are asymptotically free in the EC and LC space of p(1,0) and are strongly confined in the CC space of A(CC=-5)₃. This means that the lepton beams in the deep inelastic scattering interact with three quarks in p(1,0) by the EC interaction and weak interaction. Then, the observed spin is the partial spin of p(1,0) which is 32.6 % of the total spin (1/2) of the proton. The A(CC=-5)₃ state has the 67.4 % of the proton spin. This explains the proton spin crisis. The EC charge distribution of the proton is the same to the EC charge distribution of p(1,0) which indicates that three quarks in p(1,0) are mostly near the proton surface. From the EC charge distribution of neutron, the 2 lepton system (called as the koron) of the koron is, for the first time, reported in the present work.

The origins of the stellar mass neutron black holes and supermassive dark matter black holes without the singularities are reported based on the 4-D Euclidean space. The neutron black holes with the mass of m_BH = 5 – 15 m_sun are made by the 6-quark merged states (N_6q) of two neutrons with the mass (m(N_6q) = 10 m(n)) of 9.4 GeV/c² that gives the black hole mass gap of m_BH = 3 – 5 m_sun. Also, the supermassive black holes with the mass of m_SMBH = 10⁶ – 10¹¹ msun are made by the merged 3-D states (J(B1B2B3)₃ particles) of the dark matters. The supermassive black hole at the center of the Milky way galaxy has the mass of mSMBH = 4.1 10⁶ m_sun that is consistent with m_SMBH = 2.08 - 6.23 10⁶ m_sun calculated from the 3-D states (J(B1B2B3)₃ particles) of the dark matters with the mass of m(J) = 1.95 10¹⁵ eV/c². In other words, this supports the existence of the B1, B2 and B3 dark matters with the proposed masses. The first dark matter black hole (primary black hole) was created at the big bang. This first dark matter black hole decayed to the supermassive dark matter black holes through the secondary dark matter black holes that are explained by the merged states of the J(B1B2B3)₃ particles. The universe evolution is closely connected to the decaying process of the dark matter black holes since the big bang. The dark matter cloud states are proposed at the intermediate mass black hole range of m_IMBH = 10² – 10⁵ msun. This can explain why the dark matter black holes are not observed at the intermediate mass black hole range of m_IMBH = 10² – 10⁵ m_sun.

Due to advances in power electronics technology and the evolution of automation devices, the number of electrical devices that are sensitive to power quality is rapidly increasing, and for this reason, users are increasing their demand for high quality. To meet power quality demands, many power conversion devices are used, including dynamic voltage restorers (DVRs). DVRs are rec-ognized as devices that can effectively manage problems such as voltage segment, swells, and harmonics. DVR control requires many samples for harmonic compensation, which has the dis-advantage of being complicated to implement due to fast digital signal processing computation and the application of the cyclic discrete Fourier transform. In this paper, a high-precision DVR system configuration is proposed that compensates for harmonics using a periodically equivalent time-interval sampling technique and a novel circular structured memory filter. The proposed circular structured multi-pointer memory filter is an effective filter algorithm for high-precision input voltage measurement because it can remove noise and compensate for the delay of the phase angle of the filter in voltage measurement. A simulation and DVR prototype system was built, and the feasibility and effectiveness of the phase angle multi-filter voltage detection method and the compensation method were verified by experiments.

Our matter universe is made up of four components of dark energy (DE), dark matters (DMs), leptons and quarks which are created from the decay of the primary black hole through the inflation after big bang. In the three-dimensional quantized space model, the sum (DER) of the dark energy (DE) and radiations (R) is the flat photon space and there are 39 particles of 3 dark matters, 9 leptons and 27 quarks. Generally speaking, the mass ratio of the quarks with the 27 particles is smallest and the mass ratio of the DER photon space with the 1 massless photon is largest. Therefore, the mass ratios of DER, DMs, leptons and quarks are inversely proportional to the particle numbers of DER, DMs, leptons and quarks as the first assumption. This simple rule is called as the universe mass ratio golden rule in Fig. 12. This simple rule is successfully applied to the observed mass ratios of the Planck and WMAP missions. The best particle number combination (1, 3, 9, 27) of the four components (DER, DMs, Leptons, Quarks) to explain the Planck 2018 and WMAP results is the same as the particle number combination (1, 3, 9, 27) of the 3-dimensional quantized space model. The calculated mass ratios of DER, DMs, leptons and quarks are 67.5 %, 22.5 %, 7.5 % and 2.5 %, respectively. And the calculated mass ratios of neutrinos and ordinary matters are 5.0 % and 5.0 %, respectively. The mass ratios of the dark energy (68.47(23) %) and matters (31.53(23) %) obtained from the Planck 2018 results are consistent with the calculated mass ratios of the DER (67.5 %) and matters (32.5 %). The mass ratio of the dark energy (72.1(15) %) obtained from the WMAP 9 year results is explained as the summed mass ratio (72.5 %) of DER (67.5 %) and neutrinos (5.0 %). The universe evolution including the super-massive black holes (SMBHs) is shown in Fig. 4. The accelerated space expansion of our universe requires the addition of the new dark energy. If this new dark energy is added, the mass ratio of the dark energy is a little bit increased. The difference (0.97 %) between the observed value (68.47(23) %) and calculated value (67.5 %) is explained by adding the new dark energy in Figs. 2, 4, 7, 8, 9, 10 and 11. The corrected mass ratios of DER, DMs, leptons and quarks are 68.47 %, 21.8286 %, 7.2762 % and 2.4254 %, respectively. The corrected mass ratios of the neutrinos (called as cosmic background neutrinos) and ordinary matters (OMs) are 4.8508 % and 4.8508 %, respectively. These corrected mass ratios can explain the mass ratios obtained from the WMAP and Planck missions. In other words, the mass ratios calculated from the best particle number combination support the elementary particles, dark matters and dark energy (photon space) proposed by the three-dimensional quantized space model based on the 10-D Euclidean space.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (mass), charges and absolute time are newly defined based on the 4-D Euclidean space. The photons and gravitons are understood as the 2-D space fluctuations along the space axes and 1-D time fluctuations along the time axis, respectively. This indicates that the electromagnetic (EM) and gravitational (G) waves can be unified into the so called gravityelectromagnetic (GEM) wave which has both space and time fluctuations. The photon with zero force fields is the 2EM wave because an EM wave corresponds to a charged fermion. The dark matter bosons, weak force bosons, strong force bosons are the 1-D time fluctuations which can be expressed by the G waves. This indicates that all five forces are unified by the GEM wave. It is called as the super unification theory in the present work. And the force carrying bosons and mesons are, for the first time, proposed as the possible candidates of the magnetic monopoles like the fermions and baryons are the electric monopoles. The signs of the magnetic charges quantized as q_m=cq are newly defined. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry.

Three-dimensional quantized space model is newly introduced. Quantum mechanics and relativity theory are explained in terms of the warped three-dimensional quantized spaces with the quantum time width (Dt=t_q). The energy is newly defined as the 4-dimensional space-time volume of E = cDtDV in the present work. It is shown that the wave function of the quantum mechanics is closely related to the warped quantized space shape with the space time-volume. The quantum entanglement and quantum wave function collapse are explained additionally. The special relativity theory is separated into the energy transition associated with the space-time shape transition of the matter and the momentum transition associated with the space-time location transition. Then, the quantum mechanics and the general relativity theory are about the 4-dimensional space-time volume and the 4-dimensional space-time distance, respectively.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (E=cDtDV), charges (|q|= cDt) and absolute time (ct) are newly defined based on the 4-D Euclidean space. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry. Our universe is the matter universe with the negative charges of electric charge (EC), lepton charge (LC) and color charge (CC). This first universe is made of three dark matter -, lepton -, and quark - primary black holes with the huge negative charges which cause the Coulomb repulsive forces much bigger than the gravitational forces. The huge Coulomb forces induce the inflation of the primary black holes, that decay to the super-massive black holes. The dark matter super-massive black holes surrounded by the normal matters and dark matters make the galaxies and galaxy clusters. The spiral arms of galaxies are closely related to the decay of the 3-D charged normal matter black holes to the 1-D charged normal matter black holes. The elementary leptons and quarks are created by the decay of the normal matter charged black holes, that is caused by the Coulomb forces much stronger than the gravitational forces. The Coulomb forces are very weak with the very small Coulomb constants (k₁(EC) = k_dd(EC) ) for the dark matters and very strong with the very big Coulomb constants (k₂(EC) = k_nn(EC)) for the normal matters because of the non-communication of the photons between the dark matters and normal matters. The photons are charge dependent and mass independent. But the dark matters and normal matters have the similar and very weak gravitational forces because of the communication of the gravitons between the dark matters and normal matters. The gravitons are charge independent and mass dependent. Note that the three kinds of charges (EC, LC and CC) and one kind of mass (m) exist in our matter universe. The dark matters, leptons and quarks have the charge configurations of (EC), (EC,LC) and (EC,LC,CC), respectively. Partial masses of elementary fermions are calculated, and the proton spin crisis is explained. The charged black holes are not the singularities.

The absolute time and relative time are defined in terms of the 4-D Euclidean space. Our universe is the 3-D x₁x₂x₃ quantized photon space which follows the absolute time simultaneity when the universe moves along the absolute time axis of ct. The length expansion of Dx = gDx₀ is derived under the condition of the absolute time (ct) simultaneity. From the similarity between this length expansion of Dx = gDx₀ and the energy increasing of E = gE₀, it is assumed that the energy is proportional to the particle size of Dx. The extension of this assumption to the 4-D Euclidean space gives the new definition that the particle energy (E) is the 4-D volume. Then, the particle mass energy is defined as E= mc² = cDtDV = gE₀. The masses of the elementary particles are originated from the 4-D warped volume of the photon space because the particle is the warped photon space with the velocity of v < c. Therefore, the Higgs boson concept in the standard model (SM) is not needed in the present 3-D quantized space model (TQSM). The scalar boson with the spin of zero, photon with the spin of 1 and graviton with the spin of 2 are the two-boson states. Therefore, the observed Higgs boson is reinterpreted as the two-boson state of the scalar boson with the spin of zero. The cosmic muon observation and twin paradox are explained by using the absolute time and relative time. The relative time is the observed time in the twin paradox and cosmic muon observation. In the twin paradox, a person who travels the long distance is more aged than a person on the earth in terms of the relative time ages because of the space and time conversion effect (STCE effect) of the moving space distance (x). But twins are in the same ages in terms of the absolute time without STCE effect. The fast-moving cosmic muon has the expanded half-life from the time expansion of the relative time. Also, the quantum entanglement and Pauli exclusion principle are explained. The quantum base of the photon space line connects two entangled particles. Two particles and quantum base system is fluctuated along the absolute time axis by the time clicking when one particle is measured. Another particle is instantly selected by the time clicking. This is called as the quantum entanglement. The photons which are the flat photon space with the constant speed of c along the space axis and absolute time axis have the 4-D photon velocity of c_eff = 2^0.5 c. Total 10-D Euclidean space including three 3-D quantized spaces and one absolute time axis is required for the electric charges (EC), lepton charges (CC) and color charges (CC) of the elementary particles. The 3-D photon space is very stiff along the absolute time (ct) axis and very soft along the space axes. The Coulomb force through the photons (2EM waves) of the space fluctuations is much stronger than the Gravitational force through the gravitons (G waves) of the time fluctuations between two electrons.

The 2020 revision of South Korea’s Personal Information Protection Act (PIPA) updated procedures for the use of medical data for research. The PIPA provision allowing “pseudonymized information” to be used without the consent of the data subject for scientific research introduced ambiguity regarding the applicability of the PIPA versus the Bioethics and Safety Act (BSA), which allows “anonymized information” to be used for research only after data-subject consent and IRB approval for human-subject research are obtained. The main points requiring clarification include the distinction between “human-subject” and “scientific” research, the definition of anonymization and pseudonymization, the requirements for data-subject consent, and the procedures for institutional review boards (IRBs) and data review boards (DRBs). After reviewing the legal concepts and processes, this article recommends clarification of the guidelines for the use of medical data in research by distinguishing the concept and, in the long run, categorizing medical data based on the degree of risk.

The purpose of this study is to analyze the causes of cost variation in natural disaster prevention projects (NDPP) in Gyeongsangbuk-do and to develop effective cost and risk management strategies. The study collected data by conducting an online survey of 244 stakeholders. Binary logistic regression was used to analyze the impact of various variables on cost deviation, in-cluding project management risk (PMR), project costing and execution risk (PCER), project exe-cution strategy risk (PESR), construction project risk (CPR), project cost and schedule risk (PCSR), project management challenges (PMC), and construction project subcontractor and safety man-agement (CPSSM). The results showed that PMR (OR=3.744, 95% C.I. [1.657, 8.457]), PCER (OR=5.068, 95% C.I. [2.236, 11.484]), PESR (OR=3.447, 95% C.I. [1. 853, 6.413]), CPR (OR=2.292, 95% C.I. [1.020, 5.151]), PCSR (OR=4.817, 95% C.I. [2.250, 10.317]), PMC (OR=2.954, 95% C.I. [1.452, 6. 013]), and CPSSM (OR=2.419, 95% C.I. [1.297, 4.515]) had statistically significant effects on cost deviation. In particular, PMR, PCER, and PESR were identified as the main causes, and the effects of additional factors such as CPSSM were also important. The developed predictive model plays an important role in helping stakeholders of NDPP to manage risks in advance and take appro-priate preventive measures to ensure the success of the project. This study empirically supports the theoretical hypotheses of previous studies and provides a clear understanding of the causes of cost deviation in NDPP, which provides important insights for strategic decision-making and provides a new perspective on risk management.

In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

In this work, polyacrylic acid-functionalized MCM-41 was synthesized, which was further interacted with calcium ions, to realize enhanced pH-responsive nanocarrier for sustained drug release. First, mesoporous silica nanoparticles (MSNs) were prepared by the sol-gel method. Afterward, (3-trimethoxysilyl)propyl methacrylate (TMSPM) modified surface was prepared by using the post-grafting method, then polymerization of acrylic acid was proceeded. After adding calcium chloride solution, polyacrylic acid-functionalized MSNs with calcium-carboxyl ionic bonds in the polymeric layer, which can prevent the cargo from leaking out of the mesopore, were prepared. The structure and morphology of the modified nanoparticles (PAA-MSNs) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, etc. The controlled release of guest molecules was studied by using 5-fluorouracil (5-FU). The drug molecules-incorporated nanoparticles showed different releasing rates under different pH conditions. It is considered that our current materials have the potential as pH-responsive targeted nanocarriers in the field of medical treatment.

In this paper, we investigate the effects of certain variants of the commutative laws on properties of several families of algebras which are in general not commutative, such as groups, linear algebras, or actually quite anti-commutative, such as $BCK$-algebras and $d$-algebras among others. From results obtained it becomes clear that by considering these variants in the presence of yet other axioms it is to be expected that a quite rich and varied set of results may be obtained both in the general and the particular setting of which what has been accomplished in this paper is a substantial sample.

As climate is not only a valuable tourism resource but also a factor influencing travel experience, estimating climate change can provide implications to sustainable development of the tourism industry. This study develops Climate Volatility Index (CVI) using GARCH model and estimates the relationship between CVI and Japanese tourism demand for Korea using a tourism demand model, based on data from January 2000 to December 2013. Time lag is applied based on a decision making process regarding travel destinations. The result shows that an increase in volatility of climate change leads to a decrease in tourism demand.

Penile augmentation using filler injections is a growing trend; however, the foreign body reaction can cause complications such as ulcer and necrosis of the penis, which can requires reconstruction. The existing method of reconstruction of the penis focused on filling the deficit. We report a case involving a scrotal flap and autologous augmentation using a de-epithelialization technique for a soft tissue defect caused by delayed infection after a penile filler injection. The defect was reconstructed and an augmentation effect was achieved. The patient was a 41-year-old man who received an injection of Aquafilling® (Biomedica, Prague, Czech Republic) 7 years previously and developed a delayed infection. After debridement, the penile defect spanned the entire shaft, and the circumference of the penis was 7.5 cm. Using a bilateral scrotal flap technique, the inferior margins of both flaps were rolled inward after de-epithelialization to achieve autologous augmentation. No infection or flap necrosis occurred during the 3-month follow-up period after surgery. Additionally, the penis circumference was expanded to 12 cm, and the patient indicated that he was very satisfied with the result. This surgical technique can be widely applied as treatment for penile defects.

To solve the problem that sampling-based Rapidly-exploring Random Tree (RRT) method is difficult to guarantee optimality. This paper proposed the Post Triangular Processing of Midpoint Interpolation method minimized the planning time and shorter path length of the sampling-based algorithm. The proposed Post Triangular Processing of Midpoint Interpolation method makes a closer to the optimal path and somewhat solves the sharp path problem through the interpolation process. The experiments were conducted to verify the performance of the proposed method. Applying the method proposed in this paper to the RRT algorithm increases the efficiency of optimization compared to the planning time.

Background: Brain-derived neurotrophic factor (BDNF) has attracted increasing attention as a therapeutic agent because of its potentially biological activities, including osteogenesis. However, the molecular mechanisms involved in the osteogenic activity of BDNF have not been fully investigated. This study aimed to investigate the action of BDNF on the osteoblast differentiation in bone marrow stromal cells, and its influence on signaling pathways. Methods: Preosteoblast cells (MC3T3-E1), bone marrow-derived stromal cells (ST2), and a direct 2D co-culture system were treated with BDNF. The effect of BDNF on cell proliferation was determined using the CCK-8 assay. Osteoblast differentiation was assessed based on alkaline phosphatase (ALP) activity and staining and the protein expression of multiple osteoblast markers. Calcium accumulation was examined by Alizarin red S staining. Results: BDNF significantly increased ALP activity, calcium deposition, and the expression of osteoblast differentiation-related proteins, such as ALP, osteopontin, etc. in both ST-2 and the MC3T3-E1 and ST-2 co-culture system. Moreover, the effect of BDNF on osteogenic differentiation was diminished by blocking tropomyosin receptor kinase B as well as inhibiting c-Jun N-terminal kinase and p38 MAPK signals. Conclusion: Our study results showed positive effect of BDNF on osteogenesis. It provides essential evidence for clinical applications of BDNF in treating osteoporosis.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

Knowledge-intensive business services (KIBS) are professional services that create new added value by creating, accumulating, and disseminating new knowledge. When it comes to conducting business involving new technology, KIBS play the roles of innovator, user, and producer of new technology that has led to technological innovation. This study aimed to determine the role of KIBS as a tool for innovation in a country’s economic system. Specifically, the degree and role of their impact on the Korean economy were analyzed and compared for the entire KIBS sector, T-KIBS (a new technology-based professional service), P-KIBS (a traditional professional service), and every subsector. For this purpose, the demand-inducement model, supply inducement model, and interlinkage effects method were applied using the 2019 input-output table published in 2022. The analysis showed that the indirect production inducement effect of the entire KIBS industry on other industries was 0.800 KRW, the indirect added value inducement effect was 0.330 KRW, and the supply disruption effect was 1.144 KRW. For T-KIBS, the indirect production inducement effect was 0.687 KRW, the indirect added value inducement effect was 0.272 KRW, and the supply disruption effect was 0.730 KRW. For P-KIBS, the indirect production inducement effect was 1.472 KRW, the indirect added value inducement effect was 0.646 KRW, and the supply disruption effect was 2.657 KRW. Finally, regarding the economic ripple effect of the KIBS subsector, legal and management support services and advertisements corresponding to P-KIBS showed higher figures than the T-KIBS subsectors in all sectors, including production inducement, the added value inducement effect, and the supply disruption effect. These results revealed that in the South Korean economic system, KIBS contribute to production and value addition across all industrial sectors. It is apparent that the absence of supply significantly disrupts other industries. Furthermore, production inducement effects are evenly distributed among all the KIBS subsectors in the secondary and tertiary sectors, while the value-added effects have a greater impact on the tertiary sector. In terms of the supply shortage effects, the secondary sector experiences a more significant impact. This underscores the crucial role of KIBS in sustaining and enhancing overall economic activity in South Korea. This study is significant in that it not only investigated KIBS as an industry group using the advantages provided by industry linkage analysis but also examined and compared detailed subsectors, thereby elaborately evaluating the influence relationship between KIBS and other industries. Therefore, the results presented in this study are expected to be useful for fostering the KIBS industrial sector and establishing economic innovation policies using KIBS.

Recently, smart mobility intelligent traffic services have become a critical task in Intelligent Transportation Systems (ITS). This involves not only the use of advanced sensors and controllers but also the ability to respond to real-time traffic situations at intersections, alleviate congestion, and generate policies to prevent traffic jams. DRL (Deep Reinforcement Learning) provides a natural framework for processing tasks. In DRL, each intersection can control itself and coordinate with neighbors to achieve optimal network-wide policies. However, comparing approaches remains a challenging task due to the existence of numerous possible configurations. This research performs a critical comparison of various traffic controllers found in the literature. It demonstrates that using a nonlinear approximator for coordination mechanisms and enhancing observability at each intersection are key performance drivers.

This study has investigated the effect of nutrition labeling on consumer guilt, in situations where consumers ingest products that have an unhealthy image. The first investigation has examined the effects of types of nutrition labeling (adding healthy ingredients/reducing unhealthy ingredients). The second investigation has examined the influence of two goal-activation types(utilitarian and hedonic) and nutrition labeling on consumer guilt. The findings reveal that the utilitarian-goal-activation group felt less guilty about consuming a product with a reduced unhealthy ingredient than they did about consuming a product with an added healthy ingredient. In addition, there were interactions between the two variables, since consumer goal activation had more effect on consumer guilt about products with reduced unhealthy ingredients than on products with added healthy ingredients. Based on these results, the academic and practical implications of the present study are discussed. and proposes several directions for future research.

This study aims to assess the operational capabilities of disaster and emergency management re-sources (DEMRs), which are pivotal in mitigating risks and minimizing losses amid the increas-ing frequency of disasters. The research constructs an effective operational capability evaluation system for DEMRs, encompassing four key aspects: resource planning, organizational manage-ment capability, resource support capability, and information processing capability. It focuses on identifying the factors that influence the effective operational capability of DEMRs in China and Korea, comparing and analyzing the relative importance and priority of each evaluation domain and indicator within these countries to enhance DEMRs' operational effectiveness. The method-ology involves calculating and ranking the weight of the four domains, with findings indicating that organizational management capability is most significant in China, whereas resource sup-port capability is prioritized in Korea. A comparative analysis of the local weight of indicators within each domain revealed the largest discrepancy between China and Korea in the infor-mation processing capability domain. The study concludes by calculating global weights, identi-fying fast response capability and resource allocation capability as the most impactful factors on DEMRs' operational capability, highlighting their critical role in disaster and emergency man-agement.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. The results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

The object of this study was to discover an alternative therapeutic agent with fewer side effects against acne vulgaris, which is one of the most common skin diseases. Acne vulgaris often associates with acne-related bacteria such as <i>Propionibacterium acnes</i>, <i>Staphylococcus epidermidis</i>, <i>Staphylococcus aureus</i> and <i>Pseudomonas aeruginosa</i>, some of which exhibit a resistant against commercial antibiotics used in the treatment of acne vulgaris (tetracycline, erythromycin, and lincomycin). In the current study, we evaluated <i>in vitro</i> antibacterial activity of chitosan-phytochemical conjugates against acne-related bacteria. Three of chitosan-phytochemical conjugates used in this study showed stronger antibacterial activity than that of chitosan (unmodified control). Chitosan-caffeic acid conjugate (CCA) exhibited the highest antibacterial activity against acne-related bacteria with minimum inhibitory concentration values of 8 μg/mL to 256 μg/mL. In addition, the MICs of antibiotics against antibiotic resistant <i>P. acnes</i> and <i>P. aeruginosa</i> strains were dramatically reduced in the combination with CCA, suggesting that CCA would restore the antibacterial activity of the antibiotics. The analysis of fractional inhibitory concentration indices clearly revealed a synergistic antibacterial effect between CCA and the antibiotics. Thus, the median ∑FIC values against the antibiotic resistant bacterial strains were ranged from 0.375 to 0.533 in the combination mode of CCA and antibiotics.

Prompt removal of misfolded membrane proteins and misassembled membrane protein complexes is essential for membrane homeostasis. However, the elimination of these toxic proteins from the hydrophobic membrane environment has high energetic barriers. Transmembrane FtsH is the only known ATP-dependent protease responsible for this task, unlike other well-studied soluble ATP-dependent proteases. The mechanisms by which FtsH recognizes, unfolds, translocates, and proteolyzes its substrates remain unclear. Here, we report the crystal structures of the Thermotoga maritima FtsH periplasmic domain (PD) in an associative trimeric state at a 1.5-1.95 Å resolution. We also describe the pH-dependent oligomerization states of the isolated PD using dynamic light scattering. These observations help us understand how FtsH recognizes membrane-anchored misfolded proteins.

In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

As human activities of the countries in the East Asia have been remarkably expanding over recent decades, various problems in relation to ships, such as oil spill and many other coastal marine pollution, are continuously occurring in the coastal region. In order to conserve marine resources and prepare for possible ship accidents in advance, the need for efficient ship management is increasing over time. Multi-satellite, multi-sensor, multi-wavelength or multi-frequency observations make it possible to monitor a variety of vessels in the coastal region. This study presents the results of ship detection methodology applied to multi-spectral satellite images in the seas around Korean Peninsula based on optical, hyperspectral, and microwave remote sensing. To detect ships from hyperspectral images with a few hundreds of spectral channels, spectral matching algorithms are used to investigate similarity between the spectra and in-situ measurements. In the case of SAR (Synthetic Aperture Radar) images, the Constant False Alarm Rate (CFAR) algorithm is used to discriminate the vessels from backscattering coefficients of Sentinel-1 SAR and ALOS-2 PALSAR2 images. The present ship detection methods can be extensively utilized for optical, hyperspectral, and SAR images for comprehensive coastal management purposes toward perpetual sustainability in the future.

The investigation by the integrated approach newly introduced for this study indicates that insulin resistance (IR) would develop first preferentially in the muscle tissue with a relatively low cell turnover and then progress in sequence to the subcutaneous adipose tissue, to the visceral adipose tissue, and to the liver with higher cell turnovers. Moreover, metabolic disruptions due to IR vary widely from tissue to tissue, contrary to the conventional notion that IR merely impairs glucose uptake in the whole body. This warrants that IR be divided better into four distinct tissue specific IRs: muscle insulin resistance (MIR), subcutaneous adipose insulin resistance (s-AIR), visceral adipose insulin resistance (v-AIR), and hepatic insulin resistance (HIR). Tissue-specific IRs developing in the order of MIR, s-AIR, v-AIR, and HIR – producing tissue specific metabolic disruptions – would amount to nothing but the whole body insulin resistance (WBIR) evolving in four distinctively insulin resistant stages. The four stage metabolic evolution from rapid weight gain to visceral obesity to rapid weight loss to full blown diabetes not only complies well with the natural development history of diabetes but also resolves most of the controversies regarding obesity or diabetes, including visceral obesity, obesity paradox, and dawn phenomenon that have long remained metabolic puzzles. In addition, the four-stage WBIR evolution model refutes the entrenched notion of the lipid-induced insulin resistance (LIIR) but supports instead the glycation-induced insulin resistance (GIIR) proposed in this study. A speculation is that the glycation reaction activated ever more with WBIR evolving may serve as the common thread connecting each other a cluster of disorders or diseases that are often collectively referred to as the metabolic syndrome, such as obesity, diabetes, cardio/cerebral vasculopathy, nephropathy, neuropathy, and retinopathy.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

This study proposed to use wearable EEG to study the impact of vipassana mindfulness practice on beginner's physiological and neurological responses. Mindfulness meditation has been shown to have numerous benefits, including stress reduction, improved attention and cognitive function, and enhanced emotional regulation. The roots of mindfulness meditation in Buddhism emphasize cultivating present-moment awareness and insight. However, the neural mechanisms together with physiological mechanism and their interaction underlying these benefits remain poorly understood. Method: One middle age man (50 years old) participated in this longitudinal study using wearable EEG to investigate the neurophysiological change during a one-month consecutive vipassana mindfulness practice. Both EEG and heart rate responses were recorded each time, before (5 minutes), during (20 minutes), and after (5 minutes) meditation sessions. The EEG and HR data were analyzed by Matlab and EEGlab to examine changes in brainwave activity and heart rate. Results: alpha peak frequency (APF) is significantly lower after mindfulness meditation, as shown by comparison of APF before mindfulness (pre-5) and during mindfulness practice (med-20), and comparison between APF of pre-5 and after mindfulness practice (post-5). The same is with the beta peak power. While for theta peak frequency, it is significant lower during mindfulness meditation (med-20), when comparing to either pre-5 or post-5. See figure 1a. However, peak power index is not so sensitive, and it is more obvious in theta wave band. That is, the theta power peak is significantly lower after meditation, as can be observed in comparison between pre-5 and med-20, also between pre-5 and med-20. See figure 1b. STATE Heart-mean (bpm) Heart-std(bmp) pre-5 69.88 3.88 med-20 68.36 2.81 post-5 69.55 4.13 t-value test (pre-med) 0.0694 0.0003 t-value test (pre-post) 0.7934 0.3656 t-value test (post-med) 0.3193 0.0001 Table 1. The difference of Heart rate (mean and SD) in before (pre-5), during (med-20) and after (post-5)mindfulness meditation. We find significant change in standard deviation (SD) of heart rate between meditation and non-meditation mental states, as shown in table 1. The study provides insights into the underlying neurophysiological mechanisms of mindfulness meditation using wearable EEG devices. It demonstrates that in term of EEG measurement, spectrum frequency can be more sensitive than spectrum power; also heart rate variability as measured by SD is more sensitive to mean of HR. The proposed study contributes to the literature by using wearable EEG devices to collect data in a more accessible and convenient manner.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

This study focused on the precise detection and concordant analysis of circulating tumor cells (CTCs) to verify the usefulness of CTCs as promising clinical markers. CTCs are traditionally achieved using immune-fluorescence and morphological techniques. By combining two prostate cancer-specific genes (PSA and PSMA) and two epithelial-specific genes (EpCAM and KRT19), the CTC detection efficiency can be enhanced. The detection rates of localized prostate cancer (LPC), locally advanced prostate cancer (LAPC), metastatic hormone-sensitive prostate cancer (mHSPC), and metastatic castration-resistive prostate cancer (mCRPC) were 63.04 % (29/46), 70.59% (34/51), 94.34% (50/53), and 90% (126/140), respectively. Subsequent correlation analysis between the four genes, baseline PSA, and CTC count revealed that only the CTC count correlated with baseline PSA in the localized stages of prostate cancer, whereas all four genes were correlated with baseline PSA and CTC count in the metastatic stages of prostate cancer. The precise detection of CTCs using both numerical and transcriptomic analyses can improve the accuracy of biomarker investigations. This study provides valuable insights into the limitations of serum PSA testing and offers a promising alternative to diagnose and manage prostate cancer via the CTC number and specific genes for prostate cancer.

This study focused on the development and implementation of an educational simulation program based on Korean Triage and Acuity Scale (KTAS) for nurses in emergency medical centers who completed KTAS training. We also examined its educational effects based on the evaluation of clinical decision-making ability, job satisfaction, and customer orientation. The study participants were 30 nurses in the emergency medical center of a general hospital. Data were collected from May 3 to 24, 2017, and analyzed using SPSS 22.0. There was a significant difference in the mean scores in clinical decision-making ability, job satisfaction, and customer orientation before and after simulation education. In other words, emergency nurses who received KTAS-based simulation education program improved their clinical decision making ability, job satisfaction, and customer orientation. Based on the results of this study, it is expected that it can be used for KTAS education, and it was found that simulation-based education is a useful learning method for triage nurses in emergency medical center.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

The conserved MYST proteins form the largest family of histone acetyltransferases (HATs) that acetylate lysines within the N-terminal tails of histone, enabling active gene transcription. Here, we have investigated the biological and regulatory functions of the MYST family HAT Sas3 in the opportunistic human pathogenic fungus Aspergillus fumigatus using a series of genetic, biochemical, pathogenic, and transcriptomic analyses. The deletion of sas3 results in drastically reduced colony growth, asexual development, spore germination, response to stresses, and the fungal virulence. Genome-wide expression analyses have revealed that the sas3 mutant showed 2,402 significant differentially expressed genes; 1,147 up-regulated and 1,255 down-regulated. The representative up-regulated gene resulting from sas3 is hacA predicted to encode a bZIP transcription factor, whereas the UV-endonuclease UVE-1 was significantly down-regulated by sas3. Furthermore, our Western blot analyses suggest that Sas3 likely catalyzes acetylation of H3K9, K3K14, and H3K29 in A. fumigatus. In conclusion, Sas3 is associated with diverse biological processes and can be a potential target for controlling pathogenic fungi.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

Anesthetic management for pregnant suffering from airway pathology poses unique challenges. The presence of bilateral vocal cord granuloma adds further complexity to the management, as it can potentially cause airway compromise and respiratory distress. This case presents a pregnant patient with bilateral vocal cord granuloma who underwent anesthesia using high-flow nasal cannula (HFNC) oxygenation and oxygen reserve index (ORi) monitoring. A 33-year-old pregnant woman, who had undergone intubation six month ago, experienced hoarseness and was ultimately diagnosed with bilateral granuloma. Due to the significant airway obstruction, neither intubation nor ventilation was feasible, thereby requiring a surgical intervention. Before the surgical removal, the patient’s oxygenation was ensured using HFNC oxygenation. After confirming sufficient oxygenation of the patient with ORi of 0.38, the operation commenced and as it lasted approximately 3 minutes, the patient was able to tolerate the brief period without additional oxygen supply. Post-surgical excision, mask bagging and HFNC oxygenation was resumed, driving ORi to 0.39, then the operation was resumed. Throughout the procedure, SpO2 remained above 98. The combination of HFNC and ORi ensured adequate oxygenation and allowed for early detection of hypoxemia during the procedure. This approach may be a good option for managing granuloma.

Characters are one of the most important elements in composing digital animation. The appear-ance and voice of a character should be designed to express the personality and values of the character. However, it is not easy for animation producers to harmoniously match the appear-ance and voice of a character. Advances in deep learning technology have made it possible to overcome this limitation. To achieve this, firstly, an audio-visual dataset of characters is required. In this study, we construct and verify a Korean audio-visual dataset consisting of frontal face im-ages of various characters and short voice clips. We developed an application that can automati-cally extract the frontal face image and a short voice clip of a character by collecting videos up-loaded to YouTube. Through this, a dataset consisting of a total of 1,522 face images and a total of 7,999 seconds of voice clips was built based on 490 characters. Furthermore, we automatically la-bel characters by gender and age to validate the dataset. The dataset built in this study is expected to be used in various deep learning fields, such as classification, generative adversarial networks, and speech synthesis.

Aims TRAIL is a promising anticancer agent that has the potential to sensitize a wide variety of cancer or transformed cells by inducing apoptosis. However, resistance to TRAIL is a growing concern. Current manuscript aimed to employing combination treatment to investigate resveratrol induced TRAIL sensitization in NSCLC. Method A549 and HCC-15 cells were used in experimental design. Cell viability was determined by morphological image, crystal violet staining and MTT assay. Apoptosis was evaluated by LDH assay, Annexin V and DAPI staining. Autophagy and apoptosis indicator protein were examined by western blotting. TEM and puncta assay were carried out to evaluate the autophagy. MTP and ROS activity were evaluated by JC-1 and H₂DCFDA staining. Findings Resveratrol is a polyphenolic compound capable of activation of tumor suppressor p53 and its pro-apoptotic modulator PUMA. Herein, we showed the p53-independent apoptosis by decrease the expression of phosphorylated Akt-mediated suppression of NF-κB that is also substantiated with the downregulation of anti-apoptotic factors Bcl-2 and Bcl-xl in NSCLC, resulting in an attenuation of TRAIL resistance in combined treatment. Furthermore, apoptosis was induced in TRAIL-resistant lung cancer cells with a co-treatment of resveratrol and TRAIL assessed by the loss of MMP, ROS generations which resulting the translocation of cytochrome c from the mitochondria into the cytosol due to mitochondrial dysfunction. Moreover, autophagy flux was not affected by resveratrol-induced TRAIL-mediated apoptosis in NSCLC. Significance Overall, targeting the NF-κB (p65) pathway via resveratrol attenuates TRAIL resistance and induces TRAIL-mediated apoptosis which could be the effective TRAIL-based cancer therapy regimen.

To identify gender- and age-related associations between adult dental checkups and unmet dental care needs, we analyzed data of 14,000 participants, ages ≥ 19, from the 7th Korea National Health and Nutrition Examination Survey (2016–2018) (KNHANES VII). Data was collected via self-report questionnaires and interviews. Complex sample chi-square test and multiple logistic regression analysis indicated 31.7% of participants had unmet dental care needs; in the prior 12months, 67.1% had not utilized dental services, and 43.3% had not received dental checkups. Odds ratios (ORs) for dental checkups and unmet dental needs were 8.87 (CI:7.80–10.09, p < 0.001) for those who used dental services and 1.28 (CI: 1.13–1.44, p < 0.001) for those who had not. Significant age-dependent associations between those not receiving dental checkups and the rate of unmet dental care include men and women aged 50–59 years (OR: 1.77; CI = 1.22–2.58 and OR: 1.43; CI: 1.02–2.02; p = 0.040, respectively) and women ≥ 70 years (OR = 1.79, CI = 1.20–2.66, p = 0.004). Reducing unmet dental care needs requires greater public health promotion and education regarding regular dental checkups; additional practical strategies could enhance dental checkup compliance.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

FMD is a highly contagious animal disease that occurs in cloven-hoofed animals including pigs. To prevent FMD, vaccines and adjuvants are used to induce an immune response, but it is not sufficient to show the effect of preventing viral infection. In this study, we conducted to evaluate the increasing effect of FMD vaccine SP antibody by administrating Zn-ASP to 100 pigs from three test pig farms with feed. FMD vaccine antibody titer and immunological index were analyzed using an enzyme-linked immunosorbent assay (ELISA) kit, and hematological and blood biochemical parameters were analyzed using an automatic blood analyzer. The titer of FMD vaccine SP antibody in the 0.2% Zn-ASP-administered group significantly increased compared to that in the positive control group only injected with FMD vaccine at 4 weeks after the first vaccination and at 4, 8 and 16 weeks after the second vaccination, respectively (p&lt;0.05). The FMD vaccine SP antibody positive rate was 100% until shipment. IFN-γ and IgA were significantly increased by Zn-ASP administration 4 weeks after the first vaccination and 4 weeks after the second vaccination (p&lt;0.05). On the other hand, serum AST, and CPK (p&lt;0.001) were significantly decreased by Zn-ASP. Our results show that the administration of Zn-ASP is effective in enhancing the antibody titer and immunity of the FMD vaccine by FMD vaccination, and it is thought that it can be used as an oral adjuvant (OrAd) to prevent viral diseases such as FMD.

We attempted to establish an objective method to accurately evaluate the motility of bull sperm and examined the effects of media for sperm suspensions and frame rates on data of computer-assisted sperm motility analysis (CASA). Sperm incubated in Brackett and Oliphant medium (BO) more clearly showed hyperactivation-like motility than those in synthetic oviductal fluid. Sperm images captured at 150 frames per second (fps) showed a trajectory that was closer to the real pathway than those at other frame rates (30, 50, and 75 fps). We then examined the characteristics of sex-sorted and non-sorted semen using a cluster analysis followed by a discriminant analysis of sperm motility in BO at 150 fps. The results indicated that sex-sorted semen contained sperm with hyperactivation-like motility as the main subpopulation immediately after thawing and this subpopulation decreased after 2-h incubation. The main subpopulation in non-sorted semen had progressive motility that was maintained during incubation. In conclusion, usage of BO for sperm suspensions and capturing sperm motility at 150 fps by CASA were appropriate for evaluating bovine sperm motility. A discriminant analysis using data from a cluster analysis of motile sperm has the ability to accurately describe differences in the structures of sperm motility subpopulations.

We analyzed signal transduction of three constitutively activating mutants (M410T, L469R, and D590Y) and two inactivating mutants (D417N and Y558F) of the eel luteinizing hormone receptor (eel LHR), known to occur in human LHR. The objective of this study was to assess the functional effects of these mutations in signal transduction and cell surface loss of receptor. Mutant receptors were transiently expressed in Chinese hamster ovary (CHO-K1) cells. Eel LH-stimulated accumulation of cyclic adenosine monophosphate (cAMP) was measured by homogeneous time-resolved fluorescence (HTRF) assays. The loss of receptors from the cells surface was measured using an enzyme-linked immunosorbent assay (ELISA) in human embryonic kidney (HEK) 293 cells. The cAMP response in cells expressing the wild type eel LHR was increased in a dose-dependent manner using eel LH ligand stimulation. Compared with the wild type, cells expressing the activating mutants (M410T, L469R, and D590Y), exhibited a 4.0-, 19.1-, and 7.8-fold increase in basal cAMP response without agonist stimulation, respectively. Their maximal responses to agonist stimulation were approximately 65%, 52%, and 98%, respectively, of those of the wild type. The inactivating mutants (D417N and Y558F) did not completely impair signal transduction, and their maximal responses were only 33% and25 % of those of wild type. These data clearly showed that the eel LHR-L469R and D590Y, activating mutants enhanced the rate of the loss of cell surface receptors following treatment with eel LH. Thus, the loss of cell surface receptors in cells expressing mutant eel LHRs was consistent with the eel LH agonist-induced production of cAMP. Our results suggested that the activation of the eel LHR requires appropriate loss of LHR-ligand complexes from the cell surface.

There are two major proposed forms of dark energy: the cosmological constant and the quintessence scalar field. However, the former has the cosmological constant problem and the latter does not have observational evidence to support the theory. In this paper, we propose a dark energy paradigm to solve the cosmological constant problem and to predict lepton masses as evidence. The dark energy paradigm is a unified dark sector that is based on Planck's dimensional analysis, Lambda CDM, energy conservation, and force equilibrium. We find that dark energy can vary from the cosmological constant to the Planck scale. We find that the predicted values of lepton masses based on the dark energy paradigm agree with the observed values to 1% (or within error ranges).

Recently, e-commerce companies have been adopting and continuously enhancing personalized product recommendation systems, and there is active research in this field within academia. However, personalized product recommendations in offline retail stores have not yielded significant outcomes thus far. Especially for small-format offline retail businesses like convenience stores, where customer information might be limited, providing personalized product recommendations poses even greater challenges. To address this issue, this study aimed to find a solution by shifting the perspective on recommendation methods and altering the target of recommendations in existing personalized recommendation models. In this study, recommending products that customers need in an offline store was defined as suggesting products that should be introduced and displayed within the store. In other words, the recommendation focus shifted from individuals to the stores themselves. This recommendation system proposes products that individual stores have not yet introduced but are anticipated to be purchased by customers among the products managed by the headquarters. Building upon this, we devised a store-based product recommendation system. The widely used user-based collaborative filtering model, a common technique in existing recommendation systems, was adapted into a store-based collaborative filtering model. Furthermore, various rules and logic pertinent to store operations and business considerations for convenience stores were integrated to implement this store product recommendation system. The accuracy and effectiveness of the system were demonstrated through its application in actual convenience stores. Results from the pilot implementation of the system showed that 88% of the newly recommended products in individual stores were sold based on one week of sales data, and the sales revenue was 1.75 times higher than the average sales revenue of those products across the entire company. Survey results on business owners' satisfaction yielded a score of 4.2 out of 5, indicating a high level of contentment. Additional observed effects included the expansion of product range and reduction in order lead times. However, 12% of the total recommended SKUs did not sell within one week, and 34% of the SKUs did not meet the overall average sales quantity. This research holds significance in extending the scope of personalized recommendation studies from primarily online platforms to offline retail businesses like convenience stores. It provides tangible methodologies and outcomes that can be implemented in real-world settings through the construction and validation of an actual system. The study also suggests avenues for future research to address some of the identified limitations.

Background: Diffuse large B-cell lymphoma is the most common type of non-Hodgkin's lymphoma. Due to the variety of clinical manifestations, accurate diagnosis can be challenging. Here, we present a case of DLBCL that was initially misdiagnosed as a hematoma, highlighting the importance of considering malignancy in the setting of non-responsive soft tissue swelling. Methods: A 76-year-old man presented to the emergency department with right periorbital swelling and ecchymosis. The symptoms first appeared after an injury and did not resolve spontaneously. The patient was taking warfarin for atrial fibrillation. A facial bone CT revealed a large irregular homogeneous mass. An extraconal hematoma was suspected based on clinical history and radiologic findings. Incision and drainage were performed, resulting in evacuation of old blood. Despite continued drainage, the patient's symptoms worsened. A comparison with the previous CT revealed an increase in the size of the lesion. As a result, a surgical excisional biopsy was performed. Results: Biopsy of the mass showed a diffuse infiltrate of lymphocytes around the tissue. The diagnosis of diffuse large B-cell lymphoma was confirmed pathologically. The patient was referred to hematology for further management. Conclusions: DLBCL is a rare disease associated with a poor prognosis. Due to the previous injury and the use of anticoagulants, the patient was initially misdiagnosed as having a hematoma. This delayed the prompt diagnosis and affected the timing of treatment initiation. We must be aware that a malignant mass is a potential cause of unresponsive soft tissue swelling.

The aim of this study is to propose and validate the state space mode decomposition technique for precise mode separation of non-classical damping systems and closely distributed modal systems. To assess the reliability and applicability of this technique, a 40-story building with a tuned mass damper is investigated, and acceleration responses measured by the building's health monitoring system are used for the verification of the technique. The mode separation results reveal that the separated modal power spectrum becomes distorted at neighboring natural frequency ranges when the performance index only considers the concentration of power spectral energy at the target natural frequency. However, by introducing an augmented performance index that includes a constraint condition to account for distortion, more accurate mode decomposition can be achieved.

Mobile elevating work platforms (MEWPs) consist of a work platform, extending structure, and chassis, and are used to move persons to working positions. MEWPs are useful but are composed of pieces of equipment, and accidents do occur owing to equipment defects. Among these defects, accidents caused by the fracture of bolts fixed to the extension structure and swing system are increasing. This paper presents a failure analysis of the fixing bolts of MEWP. Standard procedure for failure analysis was employed in this investigation. Visual inspection, chemical analysis, tensile strength measurement, and finite element analysis (FEA) were used to analyze the failure of the fixing bolts. Using this failure analysis approach, we found the root cause of failure and proposed a means for solving this type of failure in the future. First, the chemical composition of the fixing bolt is obtained by a spectroscopy chemical analysis method, which determined that the chemical composition matched the required standard. The tensile test showed that the tensile and yield strengths were within the required capacity. The stress analysis was carried out at five different boom angles, and it was determined that the fixing bolt of MEWP can withstand the loads at all the boom angles. The outcomes of the fatigue analysis revealed that the fixing bolt fails before reaching the design requirements. The results of the fatigue analysis showed primarily that the failure of the fixing bolt was due to fatigue. A visual inspection of the fractured section of the fixing bolt also confirmed the fatigue failure. We propose a method to prevent failure of the fixing bolt of the MEWP from four different standpoints: the manufacturer, safety certification authority, safety inspection agency, and owner.

Abstract: (1) Background: existing treatment methods for neglect are concentrated on egocentric neglect and lead to various problems, such as cost/space constraints and portability. Therefore, this study seeks to determine how treatment (a.k.a., Twins Therapy, TT) can improve an existing problem in relation to neglect in stroke patients; (2) Method: The research design was a pre-post test control group design and both groups maintained existing rehabilitation treatment and added TT intervention only to the experimental group. TT intervention was conducted for a total of 20 sessions (1 session 30 min/day, 5 days/week for 4 weeks); (3) Result: as a result of comparison be-fore and after the TT intervention, there was no significant difference in MFT and MBI items (p>.05). However, the score and execution time of the Apple Cancellation Test showed significant reduction only in the experimental group (p<.05); (4) Conclusion: as a result of the study, TT im-proved not only egocentric neglect, but also allocentric neglect symptoms in stroke patients

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

To address the challenges of climate change and food security, the establishment of smart farm complexes is necessary. While there have been numerous studies on the productivity and environmental control of individual greenhouses, research on greenhouse complexes is considerably limited. Conducting environmental studies during the design phase of these complexes poses financial constraints and practical limitations in terms of on-site experiments. To identify potential issues that may arise when developing large-scale greenhouse complexes, it is possible to utilize modeling techniques using Computational Fluid Dynamics (CFD) to assess environmental concerns and location issues before constructing the facilities. Consequently, simulating large-scale CFD models that incorporate multiple greenhouses and atmospheric conditions simultaneously presents significant numerical challenges. The objective of this study was to develop a guideline for verifying CFD models for a large-scale Venlo greenhouse, where acquiring field data before construction is not feasible for designing a greenhouse complex. The verification processes of the CFD models were conducted using 2D and 3D iterative simulations of a 2-hectare greenhouse model, using the improved Grid Independence Test (GIT) and wall Y+ approaches. Subsequently, the aerodynamic characteristics were analyzed in a 3D greenhouse model to access its performance when the wind direction was 90° in summer season. The findings revealed that a grid resolution of 0.8 meters and a first layer height of 0.04 meters were suitable for developing large-scale greenhouse models, resulting in a low Root Mean Square Error (RMSE) of 3.9% and a high coefficient of determination (R2) of 0.968. This process led to a significant reduction of 38% in the number of grid cells. These results will serve as design standards for large-scale greenhouses.

Autophagy, an alternative cell death mechanism, is also termed programmed cell death type II. Autophagy in cancer treatment needs to be regulated. In our study, autophagy inhibition by desipramine or the autophagy inhibitor chloroquine (CQ) enhanced tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) receptor-2 [death receptor (DR5)] expression and subsequently TRAIL-induced apoptosis in TRAIL-resistant A549 lung cancer cells. Genetic inhibition of DR5 substantially reduced desipramine-enhanced TRAIL-mediated apoptosis, proving that DR5 was required to increase TRAIL sensitivity in TRAIL-resistant cancer cells. Desipramine treatment upregulated p62 expression and promoted conversion of light chain 3 (LC3)-I to its lipid-conjugated form, LC3-II, indicating that autophagy inhibition occurred at the final stages of autophagic flux. Transmission electron microscopy analysis showed the presence of condensed autophagosomes, which resulted from the late stages of autophagy inhibition by desipramine. TRAIL, in combination with desipramine or CQ, augmented the expression of apoptosis-related proteins cleaved caspase-8 and cleaved caspase-3. Our results contributed to the understanding of the mechanism underlying the synergistic anti-cancer effect of desipramine and TRAIL and presented a novel mechanism of DR5 upregulation. These findings demonstrated that autophagic flux inhibition by desipramine potentiated TRAIL-induced apoptosis, suggesting that appropriate regulation of autophagy is required for sensitizing TRAIL-resistant cancer cells to TRAIL-mediated apoptosis.

Three species of subfamily Cultrinae currently live in Korea, but Erythroculter erythropterus has been introduced into the Nakdonggang River and has taken over the habitat, reducing the habitat of Culter brevicauda. Only the endangered species C. brevicauda still lives in the Yeongsangang River, and it is necessary to be careful not to introduce E. erythropterus in the future. And Hemiculter eigenmanni is also found throughout the country. In order to effectively manage and conserve the species in its various habitats and against invasions, this study was initiated. The ultrastructure of the egg envelopes of three species of Cultrinae— E. erythropterus, C. brevicauda, and H. eigenmanni, inhabiting the Geumgang and Yeongsangang Rivers were observed. It was found that the zona radiata of the egg envelopes of all three species were divided into two layers–an outer and inner layer, with the outer surface having a non-structural form. This form is characteristic of fishes with muddy, stagnant habitats or spawning grounds. The number of pore canals on the surface of the egg envelopes was 83 for E. erythropterus, 75 for C. brevicauda, and 58 for H. eigenmanni per 10 ㎛2, and the thickness was 7.89±0.34 ㎛, 12.27±0.46 ㎛, and 7.42±0.24 ㎛, respectively. The shape of the micropyle demonstrated a funnel shape narrowing toward the inner diameter in all three species, and the size of the inner diameter was 6.62±0.29 (6.09~7.10) ㎛ in E. erythropterus, 4.19±0.39 (3.39~4.58) ㎛in C. brevicauda, and 3.98±0.46 (3.47~4.93) ㎛in H. eigenmanni. The differences between species were identified in the number of pore canals, thickness, and micropyle inner diameter of egg envelopes, which were species-specific. Our study revealed a morphological mechanism in the egg envelope that prevents the formation of interspecific hybrids, and these features can be taxonomic traits that clarify species names. It also provided useful data for the production (breeding) of the second generation in aquaculture.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

The weakness of the dispersion-managed link combined with optical phase conjugation to compensate for optical signal distortion caused by chromatic dispersion and nonlinear Kerr effect of standard single mode fiber is its limited structural flexibility. We propose dispersion map that can simultaneously compensate for the distorted wavelength division multiplexed signal while increasing the configurational flexibility. Each residual dispersion per span (RDPS) in the former half of the proposed link is randomly determined, and in the latter half, the arrangement order of RDPS is the same as or inverted in the former half. We confirm that the dispersion maps in which the RDPS distribution pattern in the latter half is opposite to the arrangement order in the former half are more effective in compensation, and rather, the compensation effect is better than in the dispersion map of the conventional scheme. The notable result of this paper is that the increase of flexibility can be achieved through random arrangement of RDPS in the former half, and the compensation improvement can be achieved by through inverse arrangement in the latter half which make the distribution profile of each half link roughly symmetric with respect to the midway optical phase conjugator.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. Initial results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Artificial Intelligence and especially machine learning have noticed rapid advancement on image processing operations. However, its involvement in the architectural design is still in its initial stages compared to other disciplines. Therefore, this paper addresses the issues of developing an integrated bottom up digital design approach and details a research framework for the incorporation of Deep Convolutional Generative Adversarial Network (GAN) for early stage design exploration and generation of intricate and complex alternative facade designs for urban infill. This paper proposes a novel building facade design by merging two neighboring building’s architecture style, size, scale, openings, as reference to create a new building design in the same neighborhood for urban infill. This newly produced building contains the outline, style and shape of the parent buildings. A 2D urban infill building design is generated as a picture where 1) neighboring buildings are imported as a reference using mobile phone and 2)iFACADE decode their spatial adjacency. It is depicted the iFACADE will be useful for designers in the early design stage to generate new façades depending on existing buildings in a short time that will save time and energy. Besides, building owners can use iFACADE to show their architects their preferred architecture facade by mixing two building styles and generating a new building. Therefore, it is depicted that iFACADE can become a communication platform in the early design stages between architects and owners. Initial results properly define a heuristic function for generating abstract design facade elements and sufficiently illustrate the desired functionality of our developed prototype.

Let ${\mathcal{SR}}^*$ be the class of starlike functions with real coefficients, i.e., the class of analytic functions $f$ which satisfy the condition $f(0)=0=f'(0)-1$, Re{z f'(z) / f (z)} > 0, for $z\in\mathbb{D}:=\{z\in\mathbb{C}:|z|<1 \}$ and $a_n:=f^{(n)}(0)/n!$ is real for all $n\in\mathbb{N}$. In the present paper, the sharp estimates of the third Hankel determinant $H_{3,1}$ over the class ${\mathcal{SR}}^*$ are computed.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).